From a7aea373b4ca428f1be2c1fedd2f26c8e3f2864d Mon Sep 17 00:00:00 2001
From: "Ira W. Snyder" <iws@ovro.caltech.edu>
Date: Thu, 23 Apr 2009 16:17:54 -0700
Subject: [PATCH 0001/1153] fsldma: use PCI Read Multiple command

By default, the Freescale 83xx DMA controller uses the PCI Read Line
command when reading data over the PCI bus. Setting the controller to use
the PCI Read Multiple command instead allows the controller to read much
larger bursts of data, which provides a drastic speed increase.

The slowdown due to using PCI Read Line was only observed when a PCI-to-PCI
bridge was between the devices trying to communicate.

A simple test driver showed an increase from 4MB/sec to 116MB/sec when
performing DMA over the PCI bus. Using DMA to transfer between blocks of
local SDRAM showed no change in performance with this patch. The dmatest
driver was also used to verify the correctness of the transfers, and showed
no errors.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 drivers/dma/fsldma.c | 10 ++++++++--
 drivers/dma/fsldma.h |  1 +
 2 files changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c
index f18d1bde043..a1cb25e277b 100644
--- a/drivers/dma/fsldma.c
+++ b/drivers/dma/fsldma.c
@@ -12,6 +12,11 @@
  *   also fit for MPC8560, MPC8555, MPC8548, MPC8641, and etc.
  *   The support for MPC8349 DMA contorller is also added.
  *
+ * This driver instructs the DMA controller to issue the PCI Read Multiple
+ * command for PCI read operations, instead of using the default PCI Read Line
+ * command. Please be aware that this setting may result in read pre-fetching
+ * on some platforms.
+ *
  * This is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
@@ -49,9 +54,10 @@ static void dma_init(struct fsl_dma_chan *fsl_chan)
 	case FSL_DMA_IP_83XX:
 		/* Set the channel to below modes:
 		 * EOTIE - End-of-transfer interrupt enable
+		 * PRC_RM - PCI read multiple
 		 */
-		DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, FSL_DMA_MR_EOTIE,
-				32);
+		DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr, FSL_DMA_MR_EOTIE
+				| FSL_DMA_MR_PRC_RM, 32);
 		break;
 	}
 
diff --git a/drivers/dma/fsldma.h b/drivers/dma/fsldma.h
index 4f21a512d84..dc7f2686579 100644
--- a/drivers/dma/fsldma.h
+++ b/drivers/dma/fsldma.h
@@ -38,6 +38,7 @@
 
 /* Special MR definition for MPC8349 */
 #define FSL_DMA_MR_EOTIE	0x00000080
+#define FSL_DMA_MR_PRC_RM	0x00000800
 
 #define FSL_DMA_SR_CH		0x00000020
 #define FSL_DMA_SR_PE		0x00000010
-- 
GitLab


From be30b226f2ae618cd719e40267d9923db1db9001 Mon Sep 17 00:00:00 2001
From: Ira Snyder <iws@ovro.caltech.edu>
Date: Thu, 28 May 2009 09:20:42 +0000
Subject: [PATCH 0002/1153] fsldma: enable external start for the 83xx
 controller

The 83xx controller has external start capability, but lacks external pause
capability. Hook up the external start function pointer for the 83xx
controller.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 drivers/dma/fsldma.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c
index a1cb25e277b..10bcf0cb0ef 100644
--- a/drivers/dma/fsldma.c
+++ b/drivers/dma/fsldma.c
@@ -877,9 +877,9 @@ static int __devinit fsl_dma_chan_probe(struct fsl_dma_device *fdev,
 
 	switch (new_fsl_chan->feature & FSL_DMA_IP_MASK) {
 	case FSL_DMA_IP_85XX:
-		new_fsl_chan->toggle_ext_start = fsl_chan_toggle_ext_start;
 		new_fsl_chan->toggle_ext_pause = fsl_chan_toggle_ext_pause;
 	case FSL_DMA_IP_83XX:
+		new_fsl_chan->toggle_ext_start = fsl_chan_toggle_ext_start;
 		new_fsl_chan->set_src_loop_size = fsl_chan_set_src_loop_size;
 		new_fsl_chan->set_dest_loop_size = fsl_chan_set_dest_loop_size;
 	}
-- 
GitLab


From 43a1a3ed6bf5a1b9ae197b4f5f20033baf19db61 Mon Sep 17 00:00:00 2001
From: Ira Snyder <iws@ovro.caltech.edu>
Date: Thu, 28 May 2009 09:26:40 +0000
Subject: [PATCH 0003/1153] fsldma: do not clear bandwidth control bits on the
 83xx controller

The 83xx controller does not support the external pause feature. The bit
in the mode register that controls external pause on the 85xx controller
happens to be part of the bandwidth control settings for the 83xx
controller.

This patch fixes the driver so that it only clears the external pause bit
if the hardware is the 85xx controller. When driving the 83xx controller,
the bit is left untouched. This follows the existing convention that mode
registers settings are not touched unless necessary.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 drivers/dma/fsldma.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c
index 10bcf0cb0ef..6e60c77a145 100644
--- a/drivers/dma/fsldma.c
+++ b/drivers/dma/fsldma.c
@@ -147,10 +147,11 @@ static void dma_start(struct fsl_dma_chan *fsl_chan)
 	if (fsl_chan->feature & FSL_DMA_CHAN_PAUSE_EXT) {
 		DMA_OUT(fsl_chan, &fsl_chan->reg_base->bcr, 0, 32);
 		mr_set |= FSL_DMA_MR_EMP_EN;
-	} else
+	} else if ((fsl_chan->feature & FSL_DMA_IP_MASK) == FSL_DMA_IP_85XX) {
 		DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr,
 			DMA_IN(fsl_chan, &fsl_chan->reg_base->mr, 32)
 				& ~FSL_DMA_MR_EMP_EN, 32);
+	}
 
 	if (fsl_chan->feature & FSL_DMA_CHAN_START_EXT)
 		mr_set |= FSL_DMA_MR_EMS_EN;
-- 
GitLab


From 04a820ead0838c76e9c1242feb5e71048bf3e9dc Mon Sep 17 00:00:00 2001
From: Andres Salomon <dilinger@collabora.co.uk>
Date: Tue, 30 Jun 2009 02:14:00 -0400
Subject: [PATCH 0004/1153] olpc_battery: Fix up eeprom read function

The eeprom read function was placing values into the wrong place in
'buf'; we were starting from buf[off], rather than buf[0].

Also, the for loop that we were using was much uglier than it needed to
be.  This cleans it up a bit.

Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
---
 drivers/power/olpc_battery.c | 17 +++++++++--------
 1 file changed, 9 insertions(+), 8 deletions(-)

diff --git a/drivers/power/olpc_battery.c b/drivers/power/olpc_battery.c
index 5fbca2681ba..9c216dd4155 100644
--- a/drivers/power/olpc_battery.c
+++ b/drivers/power/olpc_battery.c
@@ -8,6 +8,7 @@
  * published by the Free Software Foundation.
  */
 
+#include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/err.h>
 #include <linux/platform_device.h>
@@ -334,21 +335,21 @@ static ssize_t olpc_bat_eeprom_read(struct kobject *kobj,
 		struct bin_attribute *attr, char *buf, loff_t off, size_t count)
 {
 	uint8_t ec_byte;
-	int ret, end;
+	int ret;
+	int i;
 
 	if (off >= EEPROM_SIZE)
 		return 0;
 	if (off + count > EEPROM_SIZE)
 		count = EEPROM_SIZE - off;
 
-	end = EEPROM_START + off + count;
-	for (ec_byte = EEPROM_START + off; ec_byte < end; ec_byte++) {
-		ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1,
-				&buf[ec_byte - EEPROM_START], 1);
+	for (i = 0; i < count; i++) {
+		ec_byte = EEPROM_START + off + i;
+		ret = olpc_ec_cmd(EC_BAT_EEPROM, &ec_byte, 1, &buf[i], 1);
 		if (ret) {
-			printk(KERN_ERR "olpc-battery:  EC command "
-					"EC_BAT_EEPROM @ 0x%x failed -"
-					" %d!\n", ec_byte, ret);
+			pr_err("olpc-battery: "
+			       "EC_BAT_EEPROM cmd @ 0x%x failed - %d!\n",
+			       ec_byte, ret);
 			return -EIO;
 		}
 	}
-- 
GitLab


From 8f7e57985fa794ab6afdcd3642581d9e1fe6de31 Mon Sep 17 00:00:00 2001
From: Andres Salomon <dilinger@collabora.co.uk>
Date: Tue, 30 Jun 2009 02:16:17 -0400
Subject: [PATCH 0005/1153] olpc_battery: Ensure that the TRICKLE bit is
 checked

There are times when the battery is present but trickle charging,
and the EC sets only the TRICKLE bit. So we must check for the bit
when we're checking the charging/present status.

Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
---
 drivers/power/olpc_battery.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/power/olpc_battery.c b/drivers/power/olpc_battery.c
index 9c216dd4155..58e419299cd 100644
--- a/drivers/power/olpc_battery.c
+++ b/drivers/power/olpc_battery.c
@@ -36,6 +36,7 @@
 #define BAT_STAT_AC		0x10
 #define BAT_STAT_CHARGING	0x20
 #define BAT_STAT_DISCHARGING	0x40
+#define BAT_STAT_TRICKLE	0x80
 
 #define BAT_ERR_INFOFAIL	0x02
 #define BAT_ERR_OVERVOLTAGE	0x04
@@ -90,7 +91,7 @@ static char bat_serial[17]; /* Ick */
 static int olpc_bat_get_status(union power_supply_propval *val, uint8_t ec_byte)
 {
 	if (olpc_platform_info.ecver > 0x44) {
-		if (ec_byte & BAT_STAT_CHARGING)
+		if (ec_byte & (BAT_STAT_CHARGING | BAT_STAT_TRICKLE))
 			val->intval = POWER_SUPPLY_STATUS_CHARGING;
 		else if (ec_byte & BAT_STAT_DISCHARGING)
 			val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
@@ -220,7 +221,8 @@ static int olpc_bat_get_property(struct power_supply *psy,
 	   It doesn't matter though -- the EC will return the last-known
 	   information, and it's as if we just ran that _little_ bit faster
 	   and managed to read it out before the battery went away. */
-	if (!(ec_byte & BAT_STAT_PRESENT) && psp != POWER_SUPPLY_PROP_PRESENT)
+	if (!(ec_byte & (BAT_STAT_PRESENT | BAT_STAT_TRICKLE)) &&
+			psp != POWER_SUPPLY_PROP_PRESENT)
 		return -ENODEV;
 
 	switch (psp) {
@@ -230,7 +232,8 @@ static int olpc_bat_get_property(struct power_supply *psy,
 			return ret;
 		break;
 	case POWER_SUPPLY_PROP_PRESENT:
-		val->intval = !!(ec_byte & BAT_STAT_PRESENT);
+		val->intval = !!(ec_byte & (BAT_STAT_PRESENT |
+					    BAT_STAT_TRICKLE));
 		break;
 
 	case POWER_SUPPLY_PROP_HEALTH:
-- 
GitLab


From bfdb46ce8494eae30dbaae65c81e684e6db6228b Mon Sep 17 00:00:00 2001
From: Ryan Mallon <ryan@bluewatersys.com>
Date: Thu, 18 Jun 2009 11:26:26 +1200
Subject: [PATCH 0006/1153] Add ds2782 battery gas gauge driver

This patch adds a driver for ds2782 battery devices.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
---
 drivers/power/Kconfig          |   7 +
 drivers/power/Makefile         |   1 +
 drivers/power/ds2782_battery.c | 330 +++++++++++++++++++++++++++++++++
 3 files changed, 338 insertions(+)
 create mode 100644 drivers/power/ds2782_battery.c

diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index 7eda34838bf..bdbc4f73fcd 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -43,6 +43,13 @@ config BATTERY_DS2760
 	help
 	  Say Y here to enable support for batteries with ds2760 chip.
 
+config BATTERY_DS2782
+	tristate "DS2782 standalone gas-gauge"
+	depends on I2C
+	help
+	  Say Y here to enable support for the DS2782 standalone battery
+	  gas-gauge.
+
 config BATTERY_PMU
 	tristate "Apple PMU battery"
 	depends on PPC32 && ADB_PMU
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index daf3179689a..380d17c9ae2 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_APM_POWER)		+= apm_power.o
 obj-$(CONFIG_WM8350_POWER)	+= wm8350_power.o
 
 obj-$(CONFIG_BATTERY_DS2760)	+= ds2760_battery.o
+obj-$(CONFIG_BATTERY_DS2782)	+= ds2782_battery.o
 obj-$(CONFIG_BATTERY_PMU)	+= pmu_battery.o
 obj-$(CONFIG_BATTERY_OLPC)	+= olpc_battery.o
 obj-$(CONFIG_BATTERY_TOSA)	+= tosa_battery.o
diff --git a/drivers/power/ds2782_battery.c b/drivers/power/ds2782_battery.c
new file mode 100644
index 00000000000..da14f374cb6
--- /dev/null
+++ b/drivers/power/ds2782_battery.c
@@ -0,0 +1,330 @@
+/*
+ * I2C client/driver for the Maxim/Dallas DS2782 Stand-Alone Fuel Gauge IC
+ *
+ * Copyright (C) 2009 Bluewater Systems Ltd
+ *
+ * Author: Ryan Mallon <ryan@bluewatersys.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/swab.h>
+#include <linux/i2c.h>
+#include <linux/idr.h>
+#include <linux/power_supply.h>
+
+#define DS2782_REG_RARC		0x06	/* Remaining active relative capacity */
+
+#define DS2782_REG_VOLT_MSB	0x0c
+#define DS2782_REG_TEMP_MSB	0x0a
+#define DS2782_REG_CURRENT_MSB	0x0e
+
+/* EEPROM Block */
+#define DS2782_REG_RSNSP	0x69	/* Sense resistor value */
+
+/* Current unit measurement in uA for a 1 milli-ohm sense resistor */
+#define DS2782_CURRENT_UNITS	1563
+
+#define to_ds2782_info(x) container_of(x, struct ds2782_info, battery)
+
+struct ds2782_info {
+	struct i2c_client	*client;
+	struct power_supply	battery;
+	int			id;
+};
+
+static DEFINE_IDR(battery_id);
+static DEFINE_MUTEX(battery_lock);
+
+static inline int ds2782_read_reg(struct ds2782_info *info, int reg, u8 *val)
+{
+	int ret;
+
+	ret = i2c_smbus_read_byte_data(info->client, reg);
+	if (ret < 0) {
+		dev_err(&info->client->dev, "register read failed\n");
+		return ret;
+	}
+
+	*val = ret;
+	return 0;
+}
+
+static inline int ds2782_read_reg16(struct ds2782_info *info, int reg_msb,
+				    s16 *val)
+{
+	int ret;
+
+	ret = swab16(i2c_smbus_read_word_data(info->client, reg_msb));
+	if (ret < 0) {
+		dev_err(&info->client->dev, "register read failed\n");
+		return ret;
+	}
+
+	*val = ret;
+	return 0;
+}
+
+static int ds2782_get_temp(struct ds2782_info *info, int *temp)
+{
+	s16 raw;
+	int err;
+
+	/*
+	 * Temperature is measured in units of 0.125 degrees celcius, the
+	 * power_supply class measures temperature in tenths of degrees
+	 * celsius. The temperature value is stored as a 10 bit number, plus
+	 * sign in the upper bits of a 16 bit register.
+	 */
+	err = ds2782_read_reg16(info, DS2782_REG_TEMP_MSB, &raw);
+	if (err)
+		return err;
+	*temp = ((raw / 32) * 125) / 100;
+	return 0;
+}
+
+static int ds2782_get_current(struct ds2782_info *info, int *current_uA)
+{
+	int sense_res;
+	int err;
+	u8 sense_res_raw;
+	s16 raw;
+
+	/*
+	 * The units of measurement for current are dependent on the value of
+	 * the sense resistor.
+	 */
+	err = ds2782_read_reg(info, DS2782_REG_RSNSP, &sense_res_raw);
+	if (err)
+		return err;
+	if (sense_res_raw == 0) {
+		dev_err(&info->client->dev, "sense resistor value is 0\n");
+		return -ENXIO;
+	}
+	sense_res = 1000 / sense_res_raw;
+
+	dev_dbg(&info->client->dev, "sense resistor = %d milli-ohms\n",
+		sense_res);
+	err = ds2782_read_reg16(info, DS2782_REG_CURRENT_MSB, &raw);
+	if (err)
+		return err;
+	*current_uA = raw * (DS2782_CURRENT_UNITS / sense_res);
+	return 0;
+}
+
+static int ds2782_get_voltage(struct ds2782_info *info, int *voltage_uA)
+{
+	s16 raw;
+	int err;
+
+	/*
+	 * Voltage is measured in units of 4.88mV. The voltage is stored as
+	 * a 10-bit number plus sign, in the upper bits of a 16-bit register
+	 */
+	err = ds2782_read_reg16(info, DS2782_REG_VOLT_MSB, &raw);
+	if (err)
+		return err;
+	*voltage_uA = (raw / 32) * 4800;
+	return 0;
+}
+
+static int ds2782_get_capacity(struct ds2782_info *info, int *capacity)
+{
+	int err;
+	u8 raw;
+
+	err = ds2782_read_reg(info, DS2782_REG_RARC, &raw);
+	if (err)
+		return err;
+	*capacity = raw;
+	return raw;
+}
+
+static int ds2782_get_status(struct ds2782_info *info, int *status)
+{
+	int err;
+	int current_uA;
+	int capacity;
+
+	err = ds2782_get_current(info, &current_uA);
+	if (err)
+		return err;
+
+	err = ds2782_get_capacity(info, &capacity);
+	if (err)
+		return err;
+
+	if (capacity == 100)
+		*status = POWER_SUPPLY_STATUS_FULL;
+	else if (current_uA == 0)
+		*status = POWER_SUPPLY_STATUS_NOT_CHARGING;
+	else if (current_uA < 0)
+		*status = POWER_SUPPLY_STATUS_DISCHARGING;
+	else
+		*status = POWER_SUPPLY_STATUS_CHARGING;
+
+	return 0;
+}
+
+static int ds2782_battery_get_property(struct power_supply *psy,
+				       enum power_supply_property prop,
+				       union power_supply_propval *val)
+{
+	struct ds2782_info *info = to_ds2782_info(psy);
+	int ret;
+
+	switch (prop) {
+	case POWER_SUPPLY_PROP_STATUS:
+		ret = ds2782_get_status(info, &val->intval);
+		break;
+
+	case POWER_SUPPLY_PROP_CAPACITY:
+		ret = ds2782_get_capacity(info, &val->intval);
+		break;
+
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		ret = ds2782_get_voltage(info, &val->intval);
+		break;
+
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		ret = ds2782_get_current(info, &val->intval);
+		break;
+
+	case POWER_SUPPLY_PROP_TEMP:
+		ret = ds2782_get_temp(info, &val->intval);
+		break;
+
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static enum power_supply_property ds2782_battery_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_TEMP,
+};
+
+static void ds2782_power_supply_init(struct power_supply *battery)
+{
+	battery->type			= POWER_SUPPLY_TYPE_BATTERY;
+	battery->properties		= ds2782_battery_props;
+	battery->num_properties		= ARRAY_SIZE(ds2782_battery_props);
+	battery->get_property		= ds2782_battery_get_property;
+	battery->external_power_changed	= NULL;
+}
+
+static int ds2782_battery_remove(struct i2c_client *client)
+{
+	struct ds2782_info *info = i2c_get_clientdata(client);
+
+	power_supply_unregister(&info->battery);
+	kfree(info->battery.name);
+
+	mutex_lock(&battery_lock);
+	idr_remove(&battery_id, info->id);
+	mutex_unlock(&battery_lock);
+
+	i2c_set_clientdata(client, info);
+
+	kfree(info);
+	return 0;
+}
+
+static int ds2782_battery_probe(struct i2c_client *client,
+				const struct i2c_device_id *id)
+{
+	struct ds2782_info *info;
+	int ret;
+	int num;
+
+	/* Get an ID for this battery */
+	ret = idr_pre_get(&battery_id, GFP_KERNEL);
+	if (ret == 0) {
+		ret = -ENOMEM;
+		goto fail_id;
+	}
+
+	mutex_lock(&battery_lock);
+	ret = idr_get_new(&battery_id, client, &num);
+	mutex_unlock(&battery_lock);
+	if (ret < 0)
+		goto fail_id;
+
+	info = kzalloc(sizeof(*info), GFP_KERNEL);
+	if (!info) {
+		ret = -ENOMEM;
+		goto fail_info;
+	}
+
+	info->battery.name = kasprintf(GFP_KERNEL, "ds2782-%d", num);
+	if (!info->battery.name) {
+		ret = -ENOMEM;
+		goto fail_name;
+	}
+
+	i2c_set_clientdata(client, info);
+	info->client = client;
+	ds2782_power_supply_init(&info->battery);
+
+	ret = power_supply_register(&client->dev, &info->battery);
+	if (ret) {
+		dev_err(&client->dev, "failed to register battery\n");
+		goto fail_register;
+	}
+
+	return 0;
+
+fail_register:
+	kfree(info->battery.name);
+fail_name:
+	i2c_set_clientdata(client, info);
+	kfree(info);
+fail_info:
+	mutex_lock(&battery_lock);
+	idr_remove(&battery_id, num);
+	mutex_unlock(&battery_lock);
+fail_id:
+	return ret;
+}
+
+static const struct i2c_device_id ds2782_id[] = {
+	{"ds2782", 0},
+	{},
+};
+
+static struct i2c_driver ds2782_battery_driver = {
+	.driver 	= {
+		.name	= "ds2782-battery",
+	},
+	.probe		= ds2782_battery_probe,
+	.remove		= ds2782_battery_remove,
+	.id_table	= ds2782_id,
+};
+
+static int __init ds2782_init(void)
+{
+	return i2c_add_driver(&ds2782_battery_driver);
+}
+module_init(ds2782_init);
+
+static void __exit ds2782_exit(void)
+{
+	i2c_del_driver(&ds2782_battery_driver);
+}
+module_exit(ds2782_exit);
+
+MODULE_AUTHOR("Ryan Mallon <ryan@bluewatersys.com>");
+MODULE_DESCRIPTION("Maxim/Dallas DS2782 Stand-Alone Fuel Gauage IC driver");
+MODULE_LICENSE("GPL");
-- 
GitLab


From daf4219dbcbb2efcd638fcd3c29a622e1c18cc38 Mon Sep 17 00:00:00 2001
From: Dan Williams <dan.j.williams@intel.com>
Date: Wed, 1 Jul 2009 16:12:53 -0700
Subject: [PATCH 0007/1153] dmaengine: move HIGHMEM64G restriction to
 ASYNC_TX_DMA

On HIGHMEM64G systems dma_addr_t is known to be larger than (void *)
which precludes async_xor from performing dma address conversions by
reusing the input parameter address list.  However, other parts of the
dmaengine infrastructure do not suffer this constraint, so the
HIGHMEM64G restriction can be down-levelled.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 crypto/async_tx/async_xor.c | 2 +-
 drivers/dma/Kconfig         | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/crypto/async_tx/async_xor.c b/crypto/async_tx/async_xor.c
index 95fe2c8d6c5..90dd3f8bd28 100644
--- a/crypto/async_tx/async_xor.c
+++ b/crypto/async_tx/async_xor.c
@@ -300,7 +300,7 @@ EXPORT_SYMBOL_GPL(async_xor_zero_sum);
 
 static int __init async_xor_init(void)
 {
-	#ifdef CONFIG_DMA_ENGINE
+	#ifdef CONFIG_ASYNC_TX_DMA
 	/* To conserve stack space the input src_list (array of page pointers)
 	 * is reused to hold the array of dma addresses passed to the driver.
 	 * This conversion is only possible when dma_addr_t is less than the
diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index 3b3c01b6f1e..babf214a509 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -4,7 +4,7 @@
 
 menuconfig DMADEVICES
 	bool "DMA Engine support"
-	depends on !HIGHMEM64G && HAS_DMA
+	depends on HAS_DMA
 	help
 	  DMA engines can do asynchronous data transfers without
 	  involving the host CPU.  Currently, this framework can be
@@ -100,7 +100,7 @@ config NET_DMA
 
 config ASYNC_TX_DMA
 	bool "Async_tx: Offload support for the async_tx api"
-	depends on DMA_ENGINE
+	depends on DMA_ENGINE && !HIGHMEM64G
 	help
 	  This allows the async_tx api to take advantage of offload engines for
 	  memcpy, memset, xor, and raid6 p+q operations.  If your platform has
-- 
GitLab


From 8b712cd58adfe6aeeb0be4ecc011dc35620719e7 Mon Sep 17 00:00:00 2001
From: Jeff Mahoney <jeffm@suse.com>
Date: Tue, 7 Jul 2009 17:22:12 -0400
Subject: [PATCH 0008/1153] ocfs2: Fixup orphan scan cleanup after failed mount

If the mount fails for any reason, ocfs2_dismount_volume calls
ocfs2_orphan_scan_stop. It requires that ocfs2_orphan_scan_init
be called to setup the mutex and work queues, but that doesn't
happen if the mount has failed and we oops accessing an uninitialized
work queue.

This patch splits the init and startup of the orphan scan, eliminating
the oops.

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/journal.c | 8 +++++++-
 fs/ocfs2/journal.h | 1 +
 fs/ocfs2/super.c   | 4 +++-
 3 files changed, 11 insertions(+), 2 deletions(-)

diff --git a/fs/ocfs2/journal.c b/fs/ocfs2/journal.c
index f033760ecbe..c48b93ac6b6 100644
--- a/fs/ocfs2/journal.c
+++ b/fs/ocfs2/journal.c
@@ -1954,10 +1954,16 @@ void ocfs2_orphan_scan_init(struct ocfs2_super *osb)
 	os->os_osb = osb;
 	os->os_count = 0;
 	os->os_seqno = 0;
-	os->os_scantime = CURRENT_TIME;
 	mutex_init(&os->os_lock);
 	INIT_DELAYED_WORK(&os->os_orphan_scan_work, ocfs2_orphan_scan_work);
+}
 
+void ocfs2_orphan_scan_start(struct ocfs2_super *osb)
+{
+	struct ocfs2_orphan_scan *os;
+
+	os = &osb->osb_orphan_scan;
+	os->os_scantime = CURRENT_TIME;
 	if (ocfs2_is_hard_readonly(osb) || ocfs2_mount_local(osb))
 		atomic_set(&os->os_state, ORPHAN_SCAN_INACTIVE);
 	else {
diff --git a/fs/ocfs2/journal.h b/fs/ocfs2/journal.h
index 5432c7f79cc..81e8abcd246 100644
--- a/fs/ocfs2/journal.h
+++ b/fs/ocfs2/journal.h
@@ -145,6 +145,7 @@ static inline void ocfs2_inode_set_new(struct ocfs2_super *osb,
 
 /* Exported only for the journal struct init code in super.c. Do not call. */
 void ocfs2_orphan_scan_init(struct ocfs2_super *osb);
+void ocfs2_orphan_scan_start(struct ocfs2_super *osb);
 void ocfs2_orphan_scan_stop(struct ocfs2_super *osb);
 void ocfs2_orphan_scan_exit(struct ocfs2_super *osb);
 
diff --git a/fs/ocfs2/super.c b/fs/ocfs2/super.c
index 7efb349fb9b..63af2e36d83 100644
--- a/fs/ocfs2/super.c
+++ b/fs/ocfs2/super.c
@@ -1182,7 +1182,7 @@ static int ocfs2_fill_super(struct super_block *sb, void *data, int silent)
 	wake_up(&osb->osb_mount_event);
 
 	/* Start this when the mount is almost sure of being successful */
-	ocfs2_orphan_scan_init(osb);
+	ocfs2_orphan_scan_start(osb);
 
 	mlog_exit(status);
 	return status;
@@ -1981,6 +1981,8 @@ static int ocfs2_initialize_super(struct super_block *sb,
 	snprintf(osb->dev_str, sizeof(osb->dev_str), "%u,%u",
 		 MAJOR(osb->sb->s_dev), MINOR(osb->sb->s_dev));
 
+	ocfs2_orphan_scan_init(osb);
+
 	status = ocfs2_recovery_init(osb);
 	if (status) {
 		mlog(ML_ERROR, "Unable to initialize recovery state\n");
-- 
GitLab


From 17ae26b669886efe237b77439e43eb390fceb119 Mon Sep 17 00:00:00 2001
From: Jeff Liu <jeff.liu@oracle.com>
Date: Tue, 7 Jul 2009 15:51:40 +0800
Subject: [PATCH 0009/1153] ocfs2: trivial fix for s/migrate/migration/ in
 dlmrecovery.c logging

in dlmrecovery.c:1121, replace 'migrate' to 'migration' to keep the consistency
by comparing to other lines with the similar log info in the same file.

Signed-off-by: Jeff Liu <jeff.liu@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/dlm/dlmrecovery.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/ocfs2/dlm/dlmrecovery.c b/fs/ocfs2/dlm/dlmrecovery.c
index bcb9260c373..43e6e328056 100644
--- a/fs/ocfs2/dlm/dlmrecovery.c
+++ b/fs/ocfs2/dlm/dlmrecovery.c
@@ -1118,7 +1118,7 @@ static int dlm_send_mig_lockres_msg(struct dlm_ctxt *dlm,
 
 	mlog(0, "%s:%.*s: sending mig lockres (%s) to %u\n",
 	     dlm->name, res->lockname.len, res->lockname.name,
-	     orig_flags & DLM_MRES_MIGRATION ? "migrate" : "recovery",
+	     orig_flags & DLM_MRES_MIGRATION ? "migration" : "recovery",
 	     send_to);
 
 	/* send it */
-- 
GitLab


From 812e7a6a43fc34bc8f70c2b80db4ea5997d66ea8 Mon Sep 17 00:00:00 2001
From: Wengang Wang <wen.gang.wang@oracle.com>
Date: Fri, 10 Jul 2009 13:26:04 +0800
Subject: [PATCH 0010/1153] ocfs2: log the actual return value of
 ocfs2_file_aio_write()

in ocfs2_file_aio_write(), log_exit() could don't log the value
which is really returned. this patch fixes it.

Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/file.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/fs/ocfs2/file.c b/fs/ocfs2/file.c
index 62442e413a0..a49fa44aea1 100644
--- a/fs/ocfs2/file.c
+++ b/fs/ocfs2/file.c
@@ -1918,8 +1918,10 @@ out_sems:
 
 	mutex_unlock(&inode->i_mutex);
 
+	if (written)
+		ret = written;
 	mlog_exit(ret);
-	return written ? written : ret;
+	return ret;
 }
 
 static int ocfs2_splice_to_file(struct pipe_inode_info *pipe,
-- 
GitLab


From 832cc28d5bc676331e6376d940ae45d5937aa688 Mon Sep 17 00:00:00 2001
From: Florian Mickler <florian@mickler.org>
Date: Mon, 13 Jul 2009 18:40:32 +0800
Subject: [PATCH 0011/1153] drm/i915: Set lvds dual channel according to
 register from vbios

Vbios will set lvds register correctly based on
current algorithm for lingle/dual Channel LVDS when
system boot, so we can accept this configuration
directly, regardless of LVDS enable status.

It fixed freedesktop.org bug #22262

Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_display.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 508838ee31e..3371cb0ba81 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -645,7 +645,7 @@ intel_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
 	int err = target;
 
 	if (IS_I9XX(dev) && intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) &&
-	    (I915_READ(LVDS) & LVDS_PORT_EN) != 0) {
+	    (I915_READ(LVDS)) != 0) {
 		/*
 		 * For LVDS, if the panel is on, just rely on its current
 		 * settings for dual-channel.  We haven't figured out how to
-- 
GitLab


From 8a90523639f49dc4b4fa7ae47bb9c8ed73ea8577 Mon Sep 17 00:00:00 2001
From: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Sat, 11 Jul 2009 16:48:03 -0400
Subject: [PATCH 0012/1153] drm/i915: refactor error detection & collection

This patch refactors the existing error detection and collection code,
placing most of it in i915_handle_error(). Additionally, we introduce a
work queue for scheduling post-crash tasks such as generating a uevent.
Using the uevent facility, userspace should be able to capture a
post-mortem dump for diagnostics.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/i915_drv.h         |   1 +
 drivers/gpu/drm/i915/i915_gem_debugfs.c |   2 +
 drivers/gpu/drm/i915/i915_irq.c         | 232 ++++++++++++++++--------
 3 files changed, 161 insertions(+), 74 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index d0875287588..b05b44dd3bf 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -229,6 +229,7 @@ typedef struct drm_i915_private {
 
 	spinlock_t error_lock;
 	struct drm_i915_error_state *first_error;
+	struct work_struct error_work;
 
 	/* Register state */
 	u8 saveLBB;
diff --git a/drivers/gpu/drm/i915/i915_gem_debugfs.c b/drivers/gpu/drm/i915/i915_gem_debugfs.c
index 9a44bfcb813..cb3b97405fb 100644
--- a/drivers/gpu/drm/i915/i915_gem_debugfs.c
+++ b/drivers/gpu/drm/i915/i915_gem_debugfs.c
@@ -343,6 +343,8 @@ static int i915_error_state(struct seq_file *m, void *unused)
 
 	error = dev_priv->first_error;
 
+	seq_printf(m, "Time: %ld s %ld us\n", error->time.tv_sec,
+		   error->time.tv_usec);
 	seq_printf(m, "EIR: 0x%08x\n", error->eir);
 	seq_printf(m, "  PGTBL_ER: 0x%08x\n", error->pgtbl_er);
 	seq_printf(m, "  INSTPM: 0x%08x\n", error->instpm);
diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index 7ba23a69a0c..f340b3fd54e 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -290,6 +290,35 @@ irqreturn_t igdng_irq_handler(struct drm_device *dev)
 	return ret;
 }
 
+/**
+ * i915_error_work_func - do process context error handling work
+ * @work: work struct
+ *
+ * Fire an error uevent so userspace can see that a hang or error
+ * was detected.
+ */
+static void i915_error_work_func(struct work_struct *work)
+{
+	drm_i915_private_t *dev_priv = container_of(work, drm_i915_private_t,
+						    error_work);
+	struct drm_device *dev = dev_priv->dev;
+	char *event_string = "ERROR=1";
+	char *envp[] = { event_string, NULL };
+
+	DRM_DEBUG("generating error event\n");
+
+	kobject_uevent_env(&dev->primary->kdev.kobj, KOBJ_CHANGE, envp);
+}
+
+/**
+ * i915_capture_error_state - capture an error record for later analysis
+ * @dev: drm device
+ *
+ * Should be called when an error is detected (either a hang or an error
+ * interrupt) to capture error state from the time of the error.  Fills
+ * out a structure which becomes available in debugfs for user level tools
+ * to pick up.
+ */
 static void i915_capture_error_state(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
@@ -325,12 +354,137 @@ static void i915_capture_error_state(struct drm_device *dev)
 		error->acthd = I915_READ(ACTHD_I965);
 	}
 
+	do_gettimeofday(&error->time);
+
 	dev_priv->first_error = error;
 
 out:
 	spin_unlock_irqrestore(&dev_priv->error_lock, flags);
 }
 
+/**
+ * i915_handle_error - handle an error interrupt
+ * @dev: drm device
+ *
+ * Do some basic checking of regsiter state at error interrupt time and
+ * dump it to the syslog.  Also call i915_capture_error_state() to make
+ * sure we get a record and make it available in debugfs.  Fire a uevent
+ * so userspace knows something bad happened (should trigger collection
+ * of a ring dump etc.).
+ */
+static void i915_handle_error(struct drm_device *dev)
+{
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	u32 eir = I915_READ(EIR);
+	u32 pipea_stats = I915_READ(PIPEASTAT);
+	u32 pipeb_stats = I915_READ(PIPEBSTAT);
+
+	i915_capture_error_state(dev);
+
+	printk(KERN_ERR "render error detected, EIR: 0x%08x\n",
+	       eir);
+
+	if (IS_G4X(dev)) {
+		if (eir & (GM45_ERROR_MEM_PRIV | GM45_ERROR_CP_PRIV)) {
+			u32 ipeir = I915_READ(IPEIR_I965);
+
+			printk(KERN_ERR "  IPEIR: 0x%08x\n",
+			       I915_READ(IPEIR_I965));
+			printk(KERN_ERR "  IPEHR: 0x%08x\n",
+			       I915_READ(IPEHR_I965));
+			printk(KERN_ERR "  INSTDONE: 0x%08x\n",
+			       I915_READ(INSTDONE_I965));
+			printk(KERN_ERR "  INSTPS: 0x%08x\n",
+			       I915_READ(INSTPS));
+			printk(KERN_ERR "  INSTDONE1: 0x%08x\n",
+			       I915_READ(INSTDONE1));
+			printk(KERN_ERR "  ACTHD: 0x%08x\n",
+			       I915_READ(ACTHD_I965));
+			I915_WRITE(IPEIR_I965, ipeir);
+			(void)I915_READ(IPEIR_I965);
+		}
+		if (eir & GM45_ERROR_PAGE_TABLE) {
+			u32 pgtbl_err = I915_READ(PGTBL_ER);
+			printk(KERN_ERR "page table error\n");
+			printk(KERN_ERR "  PGTBL_ER: 0x%08x\n",
+			       pgtbl_err);
+			I915_WRITE(PGTBL_ER, pgtbl_err);
+			(void)I915_READ(PGTBL_ER);
+		}
+	}
+
+	if (IS_I9XX(dev)) {
+		if (eir & I915_ERROR_PAGE_TABLE) {
+			u32 pgtbl_err = I915_READ(PGTBL_ER);
+			printk(KERN_ERR "page table error\n");
+			printk(KERN_ERR "  PGTBL_ER: 0x%08x\n",
+			       pgtbl_err);
+			I915_WRITE(PGTBL_ER, pgtbl_err);
+			(void)I915_READ(PGTBL_ER);
+		}
+	}
+
+	if (eir & I915_ERROR_MEMORY_REFRESH) {
+		printk(KERN_ERR "memory refresh error\n");
+		printk(KERN_ERR "PIPEASTAT: 0x%08x\n",
+		       pipea_stats);
+		printk(KERN_ERR "PIPEBSTAT: 0x%08x\n",
+		       pipeb_stats);
+		/* pipestat has already been acked */
+	}
+	if (eir & I915_ERROR_INSTRUCTION) {
+		printk(KERN_ERR "instruction error\n");
+		printk(KERN_ERR "  INSTPM: 0x%08x\n",
+		       I915_READ(INSTPM));
+		if (!IS_I965G(dev)) {
+			u32 ipeir = I915_READ(IPEIR);
+
+			printk(KERN_ERR "  IPEIR: 0x%08x\n",
+			       I915_READ(IPEIR));
+			printk(KERN_ERR "  IPEHR: 0x%08x\n",
+			       I915_READ(IPEHR));
+			printk(KERN_ERR "  INSTDONE: 0x%08x\n",
+			       I915_READ(INSTDONE));
+			printk(KERN_ERR "  ACTHD: 0x%08x\n",
+			       I915_READ(ACTHD));
+			I915_WRITE(IPEIR, ipeir);
+			(void)I915_READ(IPEIR);
+		} else {
+			u32 ipeir = I915_READ(IPEIR_I965);
+
+			printk(KERN_ERR "  IPEIR: 0x%08x\n",
+			       I915_READ(IPEIR_I965));
+			printk(KERN_ERR "  IPEHR: 0x%08x\n",
+			       I915_READ(IPEHR_I965));
+			printk(KERN_ERR "  INSTDONE: 0x%08x\n",
+			       I915_READ(INSTDONE_I965));
+			printk(KERN_ERR "  INSTPS: 0x%08x\n",
+			       I915_READ(INSTPS));
+			printk(KERN_ERR "  INSTDONE1: 0x%08x\n",
+			       I915_READ(INSTDONE1));
+			printk(KERN_ERR "  ACTHD: 0x%08x\n",
+			       I915_READ(ACTHD_I965));
+			I915_WRITE(IPEIR_I965, ipeir);
+			(void)I915_READ(IPEIR_I965);
+		}
+	}
+
+	I915_WRITE(EIR, eir);
+	(void)I915_READ(EIR);
+	eir = I915_READ(EIR);
+	if (eir) {
+		/*
+		 * some errors might have become stuck,
+		 * mask them.
+		 */
+		DRM_ERROR("EIR stuck: 0x%08x, masking\n", eir);
+		I915_WRITE(EMR, I915_READ(EMR) | eir);
+		I915_WRITE(IIR, I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT);
+	}
+
+	schedule_work(&dev_priv->error_work);
+}
+
 irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
 {
 	struct drm_device *dev = (struct drm_device *) arg;
@@ -372,6 +526,9 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
 		pipea_stats = I915_READ(PIPEASTAT);
 		pipeb_stats = I915_READ(PIPEBSTAT);
 
+		if (iir & I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT)
+			i915_handle_error(dev);
+
 		/*
 		 * Clear the PIPE(A|B)STAT regs before the IIR
 		 */
@@ -409,80 +566,6 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
 			I915_READ(PORT_HOTPLUG_STAT);
 		}
 
-		if (iir & I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT) {
-			u32 eir = I915_READ(EIR);
-
-			i915_capture_error_state(dev);
-
-			printk(KERN_ERR "render error detected, EIR: 0x%08x\n",
-			       eir);
-			if (eir & I915_ERROR_PAGE_TABLE) {
-				u32 pgtbl_err = I915_READ(PGTBL_ER);
-				printk(KERN_ERR "page table error\n");
-				printk(KERN_ERR "  PGTBL_ER: 0x%08x\n",
-				       pgtbl_err);
-				I915_WRITE(PGTBL_ER, pgtbl_err);
-				(void)I915_READ(PGTBL_ER);
-			}
-			if (eir & I915_ERROR_MEMORY_REFRESH) {
-				printk(KERN_ERR "memory refresh error\n");
-				printk(KERN_ERR "PIPEASTAT: 0x%08x\n",
-				       pipea_stats);
-				printk(KERN_ERR "PIPEBSTAT: 0x%08x\n",
-				       pipeb_stats);
-				/* pipestat has already been acked */
-			}
-			if (eir & I915_ERROR_INSTRUCTION) {
-				printk(KERN_ERR "instruction error\n");
-				printk(KERN_ERR "  INSTPM: 0x%08x\n",
-				       I915_READ(INSTPM));
-				if (!IS_I965G(dev)) {
-					u32 ipeir = I915_READ(IPEIR);
-
-					printk(KERN_ERR "  IPEIR: 0x%08x\n",
-					       I915_READ(IPEIR));
-					printk(KERN_ERR "  IPEHR: 0x%08x\n",
-						   I915_READ(IPEHR));
-					printk(KERN_ERR "  INSTDONE: 0x%08x\n",
-						   I915_READ(INSTDONE));
-					printk(KERN_ERR "  ACTHD: 0x%08x\n",
-						   I915_READ(ACTHD));
-					I915_WRITE(IPEIR, ipeir);
-					(void)I915_READ(IPEIR);
-				} else {
-					u32 ipeir = I915_READ(IPEIR_I965);
-
-					printk(KERN_ERR "  IPEIR: 0x%08x\n",
-					       I915_READ(IPEIR_I965));
-					printk(KERN_ERR "  IPEHR: 0x%08x\n",
-					       I915_READ(IPEHR_I965));
-					printk(KERN_ERR "  INSTDONE: 0x%08x\n",
-					       I915_READ(INSTDONE_I965));
-					printk(KERN_ERR "  INSTPS: 0x%08x\n",
-					       I915_READ(INSTPS));
-					printk(KERN_ERR "  INSTDONE1: 0x%08x\n",
-					       I915_READ(INSTDONE1));
-					printk(KERN_ERR "  ACTHD: 0x%08x\n",
-					       I915_READ(ACTHD_I965));
-					I915_WRITE(IPEIR_I965, ipeir);
-					(void)I915_READ(IPEIR_I965);
-				}
-			}
-
-			I915_WRITE(EIR, eir);
-			(void)I915_READ(EIR);
-			eir = I915_READ(EIR);
-			if (eir) {
-				/*
-				 * some errors might have become stuck,
-				 * mask them.
-				 */
-				DRM_ERROR("EIR stuck: 0x%08x, masking\n", eir);
-				I915_WRITE(EMR, I915_READ(EMR) | eir);
-				I915_WRITE(IIR, I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT);
-			}
-		}
-
 		I915_WRITE(IIR, iir);
 		new_iir = I915_READ(IIR); /* Flush posted writes */
 
@@ -830,6 +913,7 @@ void i915_driver_irq_preinstall(struct drm_device * dev)
 	atomic_set(&dev_priv->irq_received, 0);
 
 	INIT_WORK(&dev_priv->hotplug_work, i915_hotplug_work_func);
+	INIT_WORK(&dev_priv->error_work, i915_error_work_func);
 
 	if (IS_IGDNG(dev)) {
 		igdng_irq_preinstall(dev);
-- 
GitLab


From 5e4d6fa72619aeea271d2ad704757717b06e291a Mon Sep 17 00:00:00 2001
From: Keith Packard <keithp@keithp.com>
Date: Sun, 12 Jul 2009 23:53:17 -0700
Subject: [PATCH 0013/1153] drm/i915: Allow frame buffers up to 4096x4096 on
 915/945 class hardware

The 915 and 945 scanout engines can handle frame buffers up to 4096 pixels
wide. Pre-9xx hardware has an 8192 byte stride limit, and so we leave the
existing 2048 max in place.

I'm not sure why we limit the height to the same value; there's no intrinsic
hardware limit in the scanout engine.

Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_display.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 3371cb0ba81..984645e26a2 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -3148,6 +3148,9 @@ void intel_modeset_init(struct drm_device *dev)
 	if (IS_I965G(dev)) {
 		dev->mode_config.max_width = 8192;
 		dev->mode_config.max_height = 8192;
+	} else if (IS_I9XX(dev)) {
+		dev->mode_config.max_width = 4096;
+		dev->mode_config.max_height = 4096;
 	} else {
 		dev->mode_config.max_width = 2048;
 		dev->mode_config.max_height = 2048;
-- 
GitLab


From ed8c754b292f02d0550596481527b7bf2b52d024 Mon Sep 17 00:00:00 2001
From: Tormod Volden <debian.tormod@gmail.com>
Date: Mon, 13 Jul 2009 22:26:48 +0200
Subject: [PATCH 0014/1153] drm/i915: ignore lvds on AOpen Mini PC MP-915

This motherboard thinks it has an LVDS connected, so without this
patch the screen goes blank on the connected VGA monitor. More
information (for the non-KMS case) in fd.o bug #18004.

Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_lvds.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c
index 9ab38efffec..43c7d9aa59c 100644
--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -778,6 +778,14 @@ static const struct dmi_system_id intel_no_lvds[] = {
 			DMI_MATCH(DMI_PRODUCT_NAME, "i965GMx-IF"),
 		},
 	},
+	{
+		.callback = intel_no_lvds_dmi_callback,
+		.ident = "AOpen Mini PC MP915",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "AOpen"),
+			DMI_MATCH(DMI_BOARD_NAME, "i915GMx-F"),
+		},
+	},
 	{
 		.callback = intel_no_lvds_dmi_callback,
 		.ident = "Aopen i945GTt-VFA",
-- 
GitLab


From dff33cfcefa31c30b72c57f44586754ea9e8f3e2 Mon Sep 17 00:00:00 2001
From: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue, 14 Jul 2009 10:15:56 -0700
Subject: [PATCH 0015/1153] drm/i915: FIFO watermark calculation fixes

I discovered several bugs in the FIFO code that was recently applied.
Some of them fell into the "how did this ever work" category, since in
some cases we were using the wrong FIFO size values, and the
calculations ended up being way off.

This patch fixes all the bugs I found, and works well on my GM45, 915GM
and 855GM test machines; but as usual with these sorts of patches
broader testing is definitely requested (in particular this patch
affects 830, 845 and 865 for which I don't have test hardware).

Overall, the patch clarifies the watermark calculation function by
adding some comments and debug info, and making the variable names a
bit clearer.  The "get FIFO size" portion of the code has also been
corrected, so we should be able to properly detect the FIFO allocations
for each pipe, for use in the watermark calculation.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/i915_reg.h      |   2 +-
 drivers/gpu/drm/i915/intel_display.c | 186 ++++++++++++++++-----------
 2 files changed, 113 insertions(+), 75 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 6c085848409..897a116cad1 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -1618,7 +1618,7 @@
 #define I830_FIFO_LINE_SIZE	32
 #define I945_FIFO_SIZE		127 /* 945 & 965 */
 #define I915_FIFO_SIZE		95
-#define I855GM_FIFO_SIZE	255
+#define I855GM_FIFO_SIZE	127 /* In cachelines */
 #define I830_FIFO_SIZE		95
 #define I915_MAX_WM		0x3f
 
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 984645e26a2..3fa0d63c83b 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -1623,44 +1623,67 @@ static struct intel_watermark_params igd_cursor_hplloff_wm = {
 	IGD_FIFO_LINE_SIZE
 };
 static struct intel_watermark_params i945_wm_info = {
-	I915_FIFO_LINE_SIZE,
+	I945_FIFO_SIZE,
 	I915_MAX_WM,
 	1,
-	0,
-	IGD_FIFO_LINE_SIZE
+	2,
+	I915_FIFO_LINE_SIZE
 };
 static struct intel_watermark_params i915_wm_info = {
-	I945_FIFO_SIZE,
+	I915_FIFO_SIZE,
 	I915_MAX_WM,
 	1,
-	0,
+	2,
 	I915_FIFO_LINE_SIZE
 };
 static struct intel_watermark_params i855_wm_info = {
 	I855GM_FIFO_SIZE,
 	I915_MAX_WM,
 	1,
-	0,
+	2,
 	I830_FIFO_LINE_SIZE
 };
 static struct intel_watermark_params i830_wm_info = {
 	I830_FIFO_SIZE,
 	I915_MAX_WM,
 	1,
-	0,
+	2,
 	I830_FIFO_LINE_SIZE
 };
 
+/**
+ * intel_calculate_wm - calculate watermark level
+ * @clock_in_khz: pixel clock
+ * @wm: chip FIFO params
+ * @pixel_size: display pixel size
+ * @latency_ns: memory latency for the platform
+ *
+ * Calculate the watermark level (the level at which the display plane will
+ * start fetching from memory again).  Each chip has a different display
+ * FIFO size and allocation, so the caller needs to figure that out and pass
+ * in the correct intel_watermark_params structure.
+ *
+ * As the pixel clock runs, the FIFO will be drained at a rate that depends
+ * on the pixel size.  When it reaches the watermark level, it'll start
+ * fetching FIFO line sized based chunks from memory until the FIFO fills
+ * past the watermark point.  If the FIFO drains completely, a FIFO underrun
+ * will occur, and a display engine hang could result.
+ */
 static unsigned long intel_calculate_wm(unsigned long clock_in_khz,
 					struct intel_watermark_params *wm,
 					int pixel_size,
 					unsigned long latency_ns)
 {
-	unsigned long bytes_required, wm_size;
+	unsigned long entries_required, wm_size;
+
+	entries_required = (clock_in_khz * pixel_size * latency_ns) / 1000000;
+	entries_required /= wm->cacheline_size;
+
+	DRM_DEBUG("FIFO entries required for mode: %d\n", entries_required);
 
-	bytes_required = (clock_in_khz * pixel_size * latency_ns) / 1000000;
-	bytes_required /= wm->cacheline_size;
-	wm_size = wm->fifo_size - bytes_required - wm->guard_size;
+	wm_size = wm->fifo_size - (entries_required + wm->guard_size);
+
+	DRM_DEBUG("FIFO watermark level: %d\n", wm_size);
 
 	if (wm_size > wm->max_wm)
 		wm_size = wm->max_wm;
@@ -1799,8 +1822,37 @@ static void igd_enable_cxsr(struct drm_device *dev, unsigned long clock,
 	return;
 }
 
-const static int latency_ns = 5000; /* default for non-igd platforms */
+const static int latency_ns = 3000; /* default for non-igd platforms */
+
+static int intel_get_fifo_size(struct drm_device *dev, int plane)
+{
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	uint32_t dsparb = I915_READ(DSPARB);
+	int size;
+
+	if (IS_I9XX(dev)) {
+		if (plane == 0)
+			size = dsparb & 0x7f;
+		else
+			size = ((dsparb >> DSPARB_CSTART_SHIFT) & 0x7f) -
+				(dsparb & 0x7f);
+	} else if (IS_I85X(dev)) {
+		if (plane == 0)
+			size = dsparb & 0x1ff;
+		else
+			size = ((dsparb >> DSPARB_BEND_SHIFT) & 0x1ff) -
+				(dsparb & 0x1ff);
+		size >>= 1; /* Convert to cachelines */
+	} else {
+		size = dsparb & 0x7f;
+		size >>= 1; /* Convert to cachelines */
+	}
+
+	DRM_DEBUG("FIFO size - (0x%08x) %s: %d\n", dsparb, plane ? "B" : "A",
+		  size);
 
+	return size;
+}
 
 static void i965_update_wm(struct drm_device *dev)
 {
@@ -1817,101 +1869,87 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock,
 			   int planeb_clock, int sr_hdisplay, int pixel_size)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
-	uint32_t fwater_lo = I915_READ(FW_BLC) & MM_FIFO_WATERMARK;
-	uint32_t fwater_hi = I915_READ(FW_BLC2) & LM_FIFO_WATERMARK;
-	int bsize, asize, cwm, bwm = 1, awm = 1, srwm = 1;
-	uint32_t dsparb = I915_READ(DSPARB);
-	int planea_entries, planeb_entries;
-	struct intel_watermark_params *wm_params;
+	uint32_t fwater_lo;
+	uint32_t fwater_hi;
+	int total_size, cacheline_size, cwm, srwm = 1;
+	int planea_wm, planeb_wm;
+	struct intel_watermark_params planea_params, planeb_params;
 	unsigned long line_time_us;
 	int sr_clock, sr_entries = 0;
 
+	/* Create copies of the base settings for each pipe */
 	if (IS_I965GM(dev) || IS_I945GM(dev))
-		wm_params = &i945_wm_info;
+		planea_params = planeb_params = i945_wm_info;
 	else if (IS_I9XX(dev))
-		wm_params = &i915_wm_info;
+		planea_params = planeb_params = i915_wm_info;
 	else
-		wm_params = &i855_wm_info;
-
-	planea_entries = intel_calculate_wm(planea_clock, wm_params,
-					    pixel_size, latency_ns);
-	planeb_entries = intel_calculate_wm(planeb_clock, wm_params,
-					    pixel_size, latency_ns);
+		planea_params = planeb_params = i855_wm_info;
 
-	DRM_DEBUG("FIFO entries - A: %d, B: %d\n", planea_entries,
-		  planeb_entries);
+	/* Grab a couple of global values before we overwrite them */
+	total_size = planea_params.fifo_size;
+	cacheline_size = planea_params.cacheline_size;
 
-	if (IS_I9XX(dev)) {
-		asize = dsparb & 0x7f;
-		bsize = (dsparb >> DSPARB_CSTART_SHIFT) & 0x7f;
-	} else {
-		asize = dsparb & 0x1ff;
-		bsize = (dsparb >> DSPARB_BEND_SHIFT) & 0x1ff;
-	}
-	DRM_DEBUG("FIFO size - A: %d, B: %d\n", asize, bsize);
+	/* Update per-plane FIFO sizes */
+	planea_params.fifo_size = intel_get_fifo_size(dev, 0);
+	planeb_params.fifo_size = intel_get_fifo_size(dev, 1);
 
-	/* Two extra entries for padding */
-	awm = asize - (planea_entries + 2);
-	bwm = bsize - (planeb_entries + 2);
-
-	/* Sanity check against potentially bad FIFO allocations */
-	if (awm <= 0) {
-		/* pipe is on but has too few FIFO entries */
-		if (planea_entries != 0)
-			DRM_DEBUG("plane A needs more FIFO entries\n");
-		awm = 1;
-	}
-	if (bwm <= 0) {
-		if (planeb_entries != 0)
-			DRM_DEBUG("plane B needs more FIFO entries\n");
-		bwm = 1;
-	}
+	planea_wm = intel_calculate_wm(planea_clock, &planea_params,
+				       pixel_size, latency_ns);
+	planeb_wm = intel_calculate_wm(planeb_clock, &planeb_params,
+				       pixel_size, latency_ns);
+	DRM_DEBUG("FIFO watermarks - A: %d, B: %d\n", planea_wm, planeb_wm);
 
 	/*
 	 * Overlay gets an aggressive default since video jitter is bad.
 	 */
 	cwm = 2;
 
-	/* Calc sr entries for one pipe configs */
+	/* Calc sr entries for one plane configs */
 	if (!planea_clock || !planeb_clock) {
+		/* self-refresh has much higher latency */
+		const static int sr_latency_ns = 6000;
+
 		sr_clock = planea_clock ? planea_clock : planeb_clock;
-		line_time_us = (sr_hdisplay * 1000) / sr_clock;
-		sr_entries = (((latency_ns / line_time_us) + 1) * pixel_size *
-			      sr_hdisplay) / 1000;
-		sr_entries = roundup(sr_entries / wm_params->cacheline_size, 1);
-		if (sr_entries < wm_params->fifo_size)
-			srwm = wm_params->fifo_size - sr_entries;
+		line_time_us = ((sr_hdisplay * 1000) / sr_clock);
+
+		/* Use ns/us then divide to preserve precision */
+		sr_entries = (((sr_latency_ns / line_time_us) + 1) *
+			      pixel_size * sr_hdisplay) / 1000;
+		sr_entries = roundup(sr_entries / cacheline_size, 1);
+		DRM_DEBUG("self-refresh entries: %d\n", sr_entries);
+		srwm = total_size - sr_entries;
+		if (srwm < 0)
+			srwm = 1;
 	}
 
 	DRM_DEBUG("Setting FIFO watermarks - A: %d, B: %d, C: %d, SR %d\n",
-		  awm, bwm, cwm, srwm);
+		  planea_wm, planeb_wm, cwm, srwm);
 
-	fwater_lo = fwater_lo | ((bwm & 0x3f) << 16) | (awm & 0x3f);
-	fwater_hi = fwater_hi | (cwm & 0x1f);
+	fwater_lo = ((planeb_wm & 0x3f) << 16) | (planea_wm & 0x3f);
+	fwater_hi = (cwm & 0x1f);
+
+	/* Set request length to 8 cachelines per fetch */
+	fwater_lo = fwater_lo | (1 << 24) | (1 << 8);
+	fwater_hi = fwater_hi | (1 << 8);
 
 	I915_WRITE(FW_BLC, fwater_lo);
 	I915_WRITE(FW_BLC2, fwater_hi);
 	if (IS_I9XX(dev))
-		I915_WRITE(FW_BLC_SELF, FW_BLC_SELF_EN | (srwm & 0x3f));
+		I915_WRITE(FW_BLC_SELF, (srwm & 0x3f));
 }
 
 static void i830_update_wm(struct drm_device *dev, int planea_clock,
 			   int pixel_size)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
-	uint32_t dsparb = I915_READ(DSPARB);
 	uint32_t fwater_lo = I915_READ(FW_BLC) & MM_FIFO_WATERMARK;
-	unsigned int asize, awm;
-	int planea_entries;
-
-	planea_entries = intel_calculate_wm(planea_clock, &i830_wm_info,
-					    pixel_size, latency_ns);
-
-	asize = dsparb & 0x7f;
+	int planea_wm;
 
-	awm = asize - planea_entries;
+	i830_wm_info.fifo_size = intel_get_fifo_size(dev, 0);
 
-	fwater_lo = fwater_lo | awm;
+	planea_wm = intel_calculate_wm(planea_clock, &i830_wm_info,
+				       pixel_size, latency_ns);
+	fwater_lo = fwater_lo | planea_wm;
 
 	I915_WRITE(FW_BLC, fwater_lo);
 }
@@ -1984,7 +2022,7 @@ static void intel_update_watermarks(struct drm_device *dev)
 	if (enabled <= 0)
 		return;
 
-	/* Single pipe configs can enable self refresh */
+	/* Single plane configs can enable self refresh */
 	if (enabled == 1 && IS_IGD(dev))
 		igd_enable_cxsr(dev, sr_clock, pixel_size);
 	else if (IS_IGD(dev))
-- 
GitLab


From ed10f95d60d41033d356fdcf88c240d7065bd5b4 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Mon, 29 Jun 2009 18:29:11 +1000
Subject: [PATCH 0016/1153] drm/radeon/kms: fix some GART table entry bugs.

1. rv370 can accept 40-bit addresses - also at 24-bit shift not 4 bits
2. rs480 table can be in 40-bit space. - 4 bit shift for top 8 bits
3. rs480 table entries can be in 40-bit space.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r100.c        |  2 +-
 drivers/gpu/drm/radeon/r300.c        |  4 +++-
 drivers/gpu/drm/radeon/radeon_gart.c |  2 +-
 drivers/gpu/drm/radeon/rs400.c       | 13 +++++++++++--
 4 files changed, 16 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index c550932a108..1b23106f955 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -110,7 +110,7 @@ int r100_pci_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr)
 	if (i < 0 || i > rdev->gart.num_gpu_pages) {
 		return -EINVAL;
 	}
-	rdev->gart.table.ram.ptr[i] = cpu_to_le32((uint32_t)addr);
+	rdev->gart.table.ram.ptr[i] = cpu_to_le32(lower_32_bits(addr));
 	return 0;
 }
 
diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c
index e2ed5bc0817..cd9ea98e9c6 100644
--- a/drivers/gpu/drm/radeon/r300.c
+++ b/drivers/gpu/drm/radeon/r300.c
@@ -150,7 +150,9 @@ int rv370_pcie_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr)
 	if (i < 0 || i > rdev->gart.num_gpu_pages) {
 		return -EINVAL;
 	}
-	addr = (((u32)addr) >> 8) | ((upper_32_bits(addr) & 0xff) << 4) | 0xC;
+	addr = (lower_32_bits(addr) >> 8) |
+	       ((upper_32_bits(addr) & 0xff) << 24) |
+	       0xc;
 	writel(cpu_to_le32(addr), ((void __iomem *)ptr) + (i * 4));
 	return 0;
 }
diff --git a/drivers/gpu/drm/radeon/radeon_gart.c b/drivers/gpu/drm/radeon/radeon_gart.c
index d343a15316e..2977539880f 100644
--- a/drivers/gpu/drm/radeon/radeon_gart.c
+++ b/drivers/gpu/drm/radeon/radeon_gart.c
@@ -177,7 +177,7 @@ int radeon_gart_bind(struct radeon_device *rdev, unsigned offset,
 			return -ENOMEM;
 		}
 		rdev->gart.pages[p] = pagelist[i];
-		page_base = (uint32_t)rdev->gart.pages_addr[p];
+		page_base = rdev->gart.pages_addr[p];
 		for (j = 0; j < (PAGE_SIZE / 4096); j++, t++) {
 			radeon_gart_set_page(rdev, t, page_base);
 			page_base += 4096;
diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c
index cc074b5a8f7..3275de4b6e3 100644
--- a/drivers/gpu/drm/radeon/rs400.c
+++ b/drivers/gpu/drm/radeon/rs400.c
@@ -164,7 +164,9 @@ int rs400_gart_enable(struct radeon_device *rdev)
 		WREG32(RADEON_BUS_CNTL, tmp);
 	}
 	/* Table should be in 32bits address space so ignore bits above. */
-	tmp = rdev->gart.table_addr & 0xfffff000;
+	tmp = (u32)rdev->gart.table_addr & 0xfffff000;
+	tmp |= (upper_32_bits(rdev->gart.table_addr) & 0xff) << 4;
+
 	WREG32_MC(RS480_GART_BASE, tmp);
 	/* TODO: more tweaking here */
 	WREG32_MC(RS480_GART_FEATURE_ID,
@@ -201,10 +203,17 @@ void rs400_gart_disable(struct radeon_device *rdev)
 
 int rs400_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr)
 {
+	uint32_t entry;
+
 	if (i < 0 || i > rdev->gart.num_gpu_pages) {
 		return -EINVAL;
 	}
-	rdev->gart.table.ram.ptr[i] = cpu_to_le32(((uint32_t)addr) | 0xC);
+
+	entry = (lower_32_bits(addr) & PAGE_MASK) |
+		((upper_32_bits(addr) & 0xff) << 4) |
+		0xc;
+	entry = cpu_to_le32(entry);
+	rdev->gart.table.ram.ptr[i] = entry;
 	return 0;
 }
 
-- 
GitLab


From 4c9bc75cbc6f2f447a38a123aa6e0605fab3cb7a Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Mon, 29 Jun 2009 18:29:12 +1000
Subject: [PATCH 0017/1153] drm/radeon/kms: mmio base/size should be
 resource_size_t.

Unsigned long is incorrect for 64-bit resources on 32-bit hw.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index d61f2fc61df..e7662ba9abf 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -594,8 +594,8 @@ struct radeon_device {
 	struct radeon_object		*fbdev_robj;
 	struct radeon_framebuffer	*fbdev_rfb;
 	/* Register mmio */
-	unsigned long			rmmio_base;
-	unsigned long			rmmio_size;
+	resource_size_t			rmmio_base;
+	resource_size_t			rmmio_size;
 	void				*rmmio;
 	radeon_rreg_t			mm_rreg;
 	radeon_wreg_t			mm_wreg;
-- 
GitLab


From 6cdf65855cf884712532fc72770baaef7bdf1b9a Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Mon, 29 Jun 2009 18:29:13 +1000
Subject: [PATCH 0018/1153] drm/radeon/kms: remove IB flushing trick.

If there is a problem then this is hiding it, we shouldn't
ever need to flush the IB. Either the buffers are:

WB - caching just works.
WC - no need to do explicit flush, the MB + readback will do it

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_ring.c | 15 +--------------
 1 file changed, 1 insertion(+), 14 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_ring.c b/drivers/gpu/drm/radeon/radeon_ring.c
index a853261d188..60d159308b8 100644
--- a/drivers/gpu/drm/radeon/radeon_ring.c
+++ b/drivers/gpu/drm/radeon/radeon_ring.c
@@ -126,32 +126,19 @@ static void radeon_ib_align(struct radeon_device *rdev, struct radeon_ib *ib)
 	}
 }
 
-static void radeon_ib_cpu_flush(struct radeon_device *rdev,
-				struct radeon_ib *ib)
-{
-	unsigned long tmp;
-	unsigned i;
-
-	/* To force CPU cache flush ugly but seems reliable */
-	for (i = 0; i < ib->length_dw; i += (rdev->cp.align_mask + 1)) {
-		tmp = readl(&ib->ptr[i]);
-	}
-}
-
 int radeon_ib_schedule(struct radeon_device *rdev, struct radeon_ib *ib)
 {
 	int r = 0;
 
 	mutex_lock(&rdev->ib_pool.mutex);
 	radeon_ib_align(rdev, ib);
-	radeon_ib_cpu_flush(rdev, ib);
 	if (!ib->length_dw || !rdev->cp.ready) {
 		/* TODO: Nothings in the ib we should report. */
 		mutex_unlock(&rdev->ib_pool.mutex);
 		DRM_ERROR("radeon: couldn't schedule IB(%lu).\n", ib->idx);
 		return -EINVAL;
 	}
-	/* 64 dwords should be enought for fence too */
+	/* 64 dwords should be enough for fence too */
 	r = radeon_ring_lock(rdev, 64);
 	if (r) {
 		DRM_ERROR("radeon: scheduling IB failled (%d).\n", r);
-- 
GitLab


From 4162338a1dab388474d4115289d1d7071623f04d Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Thu, 9 Jul 2009 15:04:19 +1000
Subject: [PATCH 0019/1153] drm/radeon/kms: set crtc and cursor offsets
 correctly on legacy chips.

The crtc and cursor offsets on the legacy chips are offset from
DISPLAY_BASE_ADDR. The code worked if display base addr was at 0,
but otherwise falls to pieces.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_cursor.c      |  2 +-
 drivers/gpu/drm/radeon/radeon_legacy_crtc.c | 11 +++++++----
 drivers/gpu/drm/radeon/radeon_mode.h        |  1 +
 3 files changed, 9 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_cursor.c b/drivers/gpu/drm/radeon/radeon_cursor.c
index 5232441f119..5f8ce370c4f 100644
--- a/drivers/gpu/drm/radeon/radeon_cursor.c
+++ b/drivers/gpu/drm/radeon/radeon_cursor.c
@@ -113,7 +113,7 @@ static void radeon_set_cursor(struct drm_crtc *crtc, struct drm_gem_object *obj,
 		WREG32(AVIVO_D1CUR_SURFACE_ADDRESS + radeon_crtc->crtc_offset, gpu_addr);
 	else
 		/* offset is from DISP(2)_BASE_ADDRESS */
-		WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, gpu_addr);
+		WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, (gpu_addr-radeon_crtc->legacy_display_base_addr));
 }
 
 int radeon_crtc_cursor_set(struct drm_crtc *crtc,
diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
index 8086ecf7f03..14c1a5107fc 100644
--- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
+++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
@@ -244,7 +244,12 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y,
 	if (radeon_gem_object_pin(obj, RADEON_GEM_DOMAIN_VRAM, &base)) {
 		return -EINVAL;
 	}
-	crtc_offset = (u32)base;
+	/* if scanout was in GTT this really wouldn't work */
+	/* crtc offset is from display base addr not FB location */
+	radeon_crtc->legacy_display_base_addr = rdev->mc.vram_location;
+
+	base -= radeon_crtc->legacy_display_base_addr;
+
 	crtc_offset_cntl = 0;
 
 	pitch_pixels = crtc->fb->pitch / (crtc->fb->bits_per_pixel / 8);
@@ -303,11 +308,9 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y,
 
 	base &= ~7;
 
-	/* update sarea TODO */
-
 	crtc_offset = (u32)base;
 
-	WREG32(RADEON_DISPLAY_BASE_ADDR + radeon_crtc->crtc_offset, rdev->mc.vram_location);
+	WREG32(RADEON_DISPLAY_BASE_ADDR + radeon_crtc->crtc_offset, radeon_crtc->legacy_display_base_addr);
 
 	if (ASIC_IS_R300(rdev)) {
 		if (radeon_crtc->crtc_id)
diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h
index 9173b687462..86f766e868e 100644
--- a/drivers/gpu/drm/radeon/radeon_mode.h
+++ b/drivers/gpu/drm/radeon/radeon_mode.h
@@ -185,6 +185,7 @@ struct radeon_crtc {
 	uint64_t cursor_addr;
 	int cursor_width;
 	int cursor_height;
+	uint32_t legacy_display_base_addr;
 };
 
 #define RADEON_USE_RMX 1
-- 
GitLab


From 3e43d82125952826202a8cd20ba84a66f3ff8808 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Thu, 9 Jul 2009 15:04:18 +1000
Subject: [PATCH 0020/1153] drm/radeon/kms: respect TOM on rs100->rs480 IGP
 variants.

Normally we are free to place VRAM where we want in the GPUs
memory address space, however on IGP chips the VRAM is actual RAM,
and no special translation or aperture is used inside the GPU MC.

So when you move the VRAM aperture away from the TOM register,
you actually move it into main memory and can trash things quite badly.

This commit makes the code respect the TOM location for MC_FB_LOCATION.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r100.c  | 5 ++++-
 drivers/gpu/drm/radeon/rs400.c | 6 ++++--
 2 files changed, 8 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index 1b23106f955..a3db56bb013 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -215,7 +215,6 @@ int r100_mc_init(struct radeon_device *rdev)
 	r100_pci_gart_disable(rdev);
 
 	/* Setup GPU memory space */
-	rdev->mc.vram_location = 0xFFFFFFFFUL;
 	rdev->mc.gtt_location = 0xFFFFFFFFUL;
 	if (rdev->flags & RADEON_IS_AGP) {
 		r = radeon_agp_init(rdev);
@@ -1265,6 +1264,8 @@ void r100_vram_info(struct radeon_device *rdev)
 		/* read NB_TOM to get the amount of ram stolen for the GPU */
 		tom = RREG32(RADEON_NB_TOM);
 		rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16);
+		/* for IGPs we need to keep VRAM where it was put by the BIOS */
+		rdev->mc.vram_location = (tom & 0xffff) << 16;
 		WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size);
 	} else {
 		rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE);
@@ -1275,6 +1276,8 @@ void r100_vram_info(struct radeon_device *rdev)
 			rdev->mc.vram_size = 8192 * 1024;
 			WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size);
 		}
+		/* let driver place VRAM */
+		rdev->mc.vram_location = 0xFFFFFFFFUL;
 	}
 
 	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c
index 3275de4b6e3..a18d053065c 100644
--- a/drivers/gpu/drm/radeon/rs400.c
+++ b/drivers/gpu/drm/radeon/rs400.c
@@ -235,7 +235,6 @@ int rs400_mc_init(struct radeon_device *rdev)
 	rdev->mc.gtt_location = rdev->mc.vram_size;
 	rdev->mc.gtt_location += (rdev->mc.gtt_size - 1);
 	rdev->mc.gtt_location &= ~(rdev->mc.gtt_size - 1);
-	rdev->mc.vram_location = 0xFFFFFFFFUL;
 	r = radeon_mc_setup(rdev);
 	if (r) {
 		return r;
@@ -305,7 +304,10 @@ void rs400_vram_info(struct radeon_device *rdev)
 	rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16);
 	WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size);
 
-	/* Could aper size report 0 ? */
+	/* RS480 IGPs don't seem to translate to main RAM, they
+	 * just reserve and scan out of it. So setting VRAM location
+	 * to say 0, will actually trash the OS. */
+	rdev->mc.vram_location = (tom & 0xffff) << 16;
 	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
 	rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0);
 }
-- 
GitLab


From 531369e62649bb8f31217cc0bf33ee6f89f1dff6 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Mon, 29 Jun 2009 11:21:25 +1000
Subject: [PATCH 0021/1153] drm/radeon: fix support for vline relocations.

Userspace sends us a special relocation type to sync video/exa
to vlines to avoid tearing, this deals with the relocation
in the kernel, it picks the correct crtc and avoids issues
where crtcs are disabled.

This version also parses the wait until to make sure it isn't
trying to do anything evil.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r100.c     | 105 ++++++++++++++++++++++++++++++
 drivers/gpu/drm/radeon/r300.c     |  13 +++-
 drivers/gpu/drm/radeon/r500_reg.h |   2 +
 drivers/gpu/drm/radeon/rv515.c    |  23 +++++--
 4 files changed, 137 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index a3db56bb013..154648a2c02 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -751,6 +751,102 @@ int r100_cs_packet_parse(struct radeon_cs_parser *p,
 	return 0;
 }
 
+/**
+ * r100_cs_packet_next_vline() - parse userspace VLINE packet
+ * @parser:		parser structure holding parsing context.
+ *
+ * Userspace sends a special sequence for VLINE waits.
+ * PACKET0 - VLINE_START_END + value
+ * PACKET0 - WAIT_UNTIL +_value
+ * RELOC (P3) - crtc_id in reloc.
+ *
+ * This function parses this and relocates the VLINE START END
+ * and WAIT UNTIL packets to the correct crtc.
+ * It also detects a switched off crtc and nulls out the
+ * wait in that case.
+ */
+int r100_cs_packet_parse_vline(struct radeon_cs_parser *p)
+{
+	struct radeon_cs_chunk *ib_chunk;
+	struct drm_mode_object *obj;
+	struct drm_crtc *crtc;
+	struct radeon_crtc *radeon_crtc;
+	struct radeon_cs_packet p3reloc, waitreloc;
+	int crtc_id;
+	int r;
+	uint32_t header, h_idx, reg;
+
+	ib_chunk = &p->chunks[p->chunk_ib_idx];
+
+	/* parse the wait until */
+	r = r100_cs_packet_parse(p, &waitreloc, p->idx);
+	if (r)
+		return r;
+
+	/* check its a wait until and only 1 count */
+	if (waitreloc.reg != RADEON_WAIT_UNTIL ||
+	    waitreloc.count != 0) {
+		DRM_ERROR("vline wait had illegal wait until segment\n");
+		r = -EINVAL;
+		return r;
+	}
+
+	if (ib_chunk->kdata[waitreloc.idx + 1] != RADEON_WAIT_CRTC_VLINE) {
+		DRM_ERROR("vline wait had illegal wait until\n");
+		r = -EINVAL;
+		return r;
+	}
+
+	/* jump over the NOP */
+	r = r100_cs_packet_parse(p, &p3reloc, p->idx);
+	if (r)
+		return r;
+
+	h_idx = p->idx - 2;
+	p->idx += waitreloc.count;
+	p->idx += p3reloc.count;
+
+	header = ib_chunk->kdata[h_idx];
+	crtc_id = ib_chunk->kdata[h_idx + 5];
+	reg = ib_chunk->kdata[h_idx] >> 2;
+	mutex_lock(&p->rdev->ddev->mode_config.mutex);
+	obj = drm_mode_object_find(p->rdev->ddev, crtc_id, DRM_MODE_OBJECT_CRTC);
+	if (!obj) {
+		DRM_ERROR("cannot find crtc %d\n", crtc_id);
+		r = -EINVAL;
+		goto out;
+	}
+	crtc = obj_to_crtc(obj);
+	radeon_crtc = to_radeon_crtc(crtc);
+	crtc_id = radeon_crtc->crtc_id;
+
+	if (!crtc->enabled) {
+		/* if the CRTC isn't enabled - we need to nop out the wait until */
+		ib_chunk->kdata[h_idx + 2] = PACKET2(0);
+		ib_chunk->kdata[h_idx + 3] = PACKET2(0);
+	} else if (crtc_id == 1) {
+		switch (reg) {
+		case AVIVO_D1MODE_VLINE_START_END:
+			header &= R300_CP_PACKET0_REG_MASK;
+			header |= AVIVO_D2MODE_VLINE_START_END >> 2;
+			break;
+		case RADEON_CRTC_GUI_TRIG_VLINE:
+			header &= R300_CP_PACKET0_REG_MASK;
+			header |= RADEON_CRTC2_GUI_TRIG_VLINE >> 2;
+			break;
+		default:
+			DRM_ERROR("unknown crtc reloc\n");
+			r = -EINVAL;
+			goto out;
+		}
+		ib_chunk->kdata[h_idx] = header;
+		ib_chunk->kdata[h_idx + 3] |= RADEON_ENG_DISPLAY_SELECT_CRTC1;
+	}
+out:
+	mutex_unlock(&p->rdev->ddev->mode_config.mutex);
+	return r;
+}
+
 /**
  * r100_cs_packet_next_reloc() - parse next packet which should be reloc packet3
  * @parser:		parser structure holding parsing context.
@@ -824,6 +920,15 @@ static int r100_packet0_check(struct radeon_cs_parser *p,
 	}
 	for (i = 0; i <= pkt->count; i++, idx++, reg += 4) {
 		switch (reg) {
+		case RADEON_CRTC_GUI_TRIG_VLINE:
+			r = r100_cs_packet_parse_vline(p);
+			if (r) {
+				DRM_ERROR("No reloc for ib[%d]=0x%04X\n",
+						idx, reg);
+				r100_cs_dump_packet(p, pkt);
+				return r;
+			}
+			break;
 		/* FIXME: only allow PACKET3 blit? easier to check for out of
 		 * range access */
 		case RADEON_DST_PITCH_OFFSET:
diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c
index cd9ea98e9c6..656d9238bb0 100644
--- a/drivers/gpu/drm/radeon/r300.c
+++ b/drivers/gpu/drm/radeon/r300.c
@@ -44,6 +44,7 @@ int r100_gui_wait_for_idle(struct radeon_device *rdev);
 int r100_cs_packet_parse(struct radeon_cs_parser *p,
 			 struct radeon_cs_packet *pkt,
 			 unsigned idx);
+int r100_cs_packet_parse_vline(struct radeon_cs_parser *p);
 int r100_cs_packet_next_reloc(struct radeon_cs_parser *p,
 			      struct radeon_cs_reloc **cs_reloc);
 int r100_cs_parse_packet0(struct radeon_cs_parser *p,
@@ -972,7 +973,7 @@ static inline void r300_cs_track_clear(struct r300_cs_track *track)
 
 static const unsigned r300_reg_safe_bm[159] = {
 	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
-	0xFFFFFFBF, 0xFFFFFFFF, 0xFFFFFFBF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
 	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
 	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
 	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
@@ -1029,6 +1030,16 @@ static int r300_packet0_check(struct radeon_cs_parser *p,
 	ib_chunk = &p->chunks[p->chunk_ib_idx];
 	track = (struct r300_cs_track*)p->track;
 	switch(reg) {
+	case AVIVO_D1MODE_VLINE_START_END:
+	case RADEON_CRTC_GUI_TRIG_VLINE:
+		r = r100_cs_packet_parse_vline(p);
+		if (r) {
+			DRM_ERROR("No reloc for ib[%d]=0x%04X\n",
+					idx, reg);
+			r100_cs_dump_packet(p, pkt);
+			return r;
+		}
+		break;
 	case RADEON_DST_PITCH_OFFSET:
 	case RADEON_SRC_PITCH_OFFSET:
 		r = r100_cs_packet_next_reloc(p, &reloc);
diff --git a/drivers/gpu/drm/radeon/r500_reg.h b/drivers/gpu/drm/radeon/r500_reg.h
index 9070a1c2ce2..036691b38cb 100644
--- a/drivers/gpu/drm/radeon/r500_reg.h
+++ b/drivers/gpu/drm/radeon/r500_reg.h
@@ -445,6 +445,7 @@
 #define AVIVO_D1MODE_DATA_FORMAT                0x6528
 #       define AVIVO_D1MODE_INTERLEAVE_EN       (1 << 0)
 #define AVIVO_D1MODE_DESKTOP_HEIGHT             0x652C
+#define AVIVO_D1MODE_VLINE_START_END            0x6538
 #define AVIVO_D1MODE_VIEWPORT_START             0x6580
 #define AVIVO_D1MODE_VIEWPORT_SIZE              0x6584
 #define AVIVO_D1MODE_EXT_OVERSCAN_LEFT_RIGHT    0x6588
@@ -496,6 +497,7 @@
 #define AVIVO_D2CUR_SIZE                        0x6c10
 #define AVIVO_D2CUR_POSITION                    0x6c14
 
+#define AVIVO_D2MODE_VLINE_START_END            0x6d38
 #define AVIVO_D2MODE_VIEWPORT_START             0x6d80
 #define AVIVO_D2MODE_VIEWPORT_SIZE              0x6d84
 #define AVIVO_D2MODE_EXT_OVERSCAN_LEFT_RIGHT    0x6d88
diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c
index ffea37b1b3e..d1384d3991a 100644
--- a/drivers/gpu/drm/radeon/rv515.c
+++ b/drivers/gpu/drm/radeon/rv515.c
@@ -509,9 +509,9 @@ int rv515_debugfs_ga_info_init(struct radeon_device *rdev)
 /*
  * Asic initialization
  */
-static const unsigned r500_reg_safe_bm[159] = {
+static const unsigned r500_reg_safe_bm[219] = {
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
 	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
-	0xFFFFFFBF, 0xFFFFFFFF, 0xFFFFFFBF, 0xFFFFFFFF,
 	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
 	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
 	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
@@ -549,11 +549,24 @@ static const unsigned r500_reg_safe_bm[159] = {
 	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
 	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFF80FFFF,
 	0x00000000, 0x00000000, 0x00000000, 0x00000000,
-	0x0003FC01, 0x3FFFFCF8, 0xFE800B19,
+	0x0003FC01, 0x3FFFFCF8, 0xFE800B19, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
+	0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF,
 };
 
-
-
 int rv515_init(struct radeon_device *rdev)
 {
 	rdev->config.r300.reg_safe_bm = r500_reg_safe_bm;
-- 
GitLab


From d1724078d6a01177c1db4ea0b75fda1ca8a73d57 Mon Sep 17 00:00:00 2001
From: Thomas Hellstrom <thellstrom@vmware.com>
Date: Wed, 24 Jun 2009 19:57:35 +0200
Subject: [PATCH 0022/1153] ttm: Make messages more readable.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 include/drm/ttm/ttm_module.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/drm/ttm/ttm_module.h b/include/drm/ttm/ttm_module.h
index 889a4c7958a..d1d433834e4 100644
--- a/include/drm/ttm/ttm_module.h
+++ b/include/drm/ttm/ttm_module.h
@@ -33,7 +33,7 @@
 
 #include <linux/kernel.h>
 
-#define TTM_PFX "[TTM]"
+#define TTM_PFX "[TTM] "
 
 enum ttm_global_types {
 	TTM_GLOBAL_TTM_MEM = 0,
-- 
GitLab


From ae3e8122cbf8f9301369f276f4179aa6ec1b5b9c Mon Sep 17 00:00:00 2001
From: Thomas Hellstrom <thellstrom@vmware.com>
Date: Wed, 24 Jun 2009 19:57:34 +0200
Subject: [PATCH 0023/1153] ttm: Fix caching mode selection.

A bug caused a new caching state to be selected on each buffer object
validation regardless of the current caching state.
Moreover, a caching state could be selected that wasn't supported by
the memory type.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/ttm/ttm_bo.c | 51 +++++++++++++++++++++++++++---------
 1 file changed, 39 insertions(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c
index c1c407f7cca..a753598a5e3 100644
--- a/drivers/gpu/drm/ttm/ttm_bo.c
+++ b/drivers/gpu/drm/ttm/ttm_bo.c
@@ -655,31 +655,52 @@ retry_pre_get:
 	return 0;
 }
 
+static uint32_t ttm_bo_select_caching(struct ttm_mem_type_manager *man,
+				      uint32_t cur_placement,
+				      uint32_t proposed_placement)
+{
+	uint32_t caching = proposed_placement & TTM_PL_MASK_CACHING;
+	uint32_t result = proposed_placement & ~TTM_PL_MASK_CACHING;
+
+	/**
+	 * Keep current caching if possible.
+	 */
+
+	if ((cur_placement & caching) != 0)
+		result |= (cur_placement & caching);
+	else if ((man->default_caching & caching) != 0)
+		result |= man->default_caching;
+	else if ((TTM_PL_FLAG_CACHED & caching) != 0)
+		result |= TTM_PL_FLAG_CACHED;
+	else if ((TTM_PL_FLAG_WC & caching) != 0)
+		result |= TTM_PL_FLAG_WC;
+	else if ((TTM_PL_FLAG_UNCACHED & caching) != 0)
+		result |= TTM_PL_FLAG_UNCACHED;
+
+	return result;
+}
+
+
 static bool ttm_bo_mt_compatible(struct ttm_mem_type_manager *man,
 				 bool disallow_fixed,
 				 uint32_t mem_type,
-				 uint32_t mask, uint32_t *res_mask)
+				 uint32_t proposed_placement,
+				 uint32_t *masked_placement)
 {
 	uint32_t cur_flags = ttm_bo_type_flags(mem_type);
 
 	if ((man->flags & TTM_MEMTYPE_FLAG_FIXED) && disallow_fixed)
 		return false;
 
-	if ((cur_flags & mask & TTM_PL_MASK_MEM) == 0)
+	if ((cur_flags & proposed_placement & TTM_PL_MASK_MEM) == 0)
 		return false;
 
-	if ((mask & man->available_caching) == 0)
+	if ((proposed_placement & man->available_caching) == 0)
 		return false;
-	if (mask & man->default_caching)
-		cur_flags |= man->default_caching;
-	else if (mask & TTM_PL_FLAG_CACHED)
-		cur_flags |= TTM_PL_FLAG_CACHED;
-	else if (mask & TTM_PL_FLAG_WC)
-		cur_flags |= TTM_PL_FLAG_WC;
-	else
-		cur_flags |= TTM_PL_FLAG_UNCACHED;
 
-	*res_mask = cur_flags;
+	cur_flags |= (proposed_placement & man->available_caching);
+
+	*masked_placement = cur_flags;
 	return true;
 }
 
@@ -723,6 +744,9 @@ int ttm_bo_mem_space(struct ttm_buffer_object *bo,
 		if (!type_ok)
 			continue;
 
+		cur_flags = ttm_bo_select_caching(man, bo->mem.placement,
+						  cur_flags);
+
 		if (mem_type == TTM_PL_SYSTEM)
 			break;
 
@@ -779,6 +803,9 @@ int ttm_bo_mem_space(struct ttm_buffer_object *bo,
 					  proposed_placement, &cur_flags))
 			continue;
 
+		cur_flags = ttm_bo_select_caching(man, bo->mem.placement,
+						  cur_flags);
+
 		ret = ttm_bo_mem_force_space(bdev, mem, mem_type,
 					     interruptible, no_wait);
 
-- 
GitLab


From 848577ee27f704231b1860ae987a1be78b88b06e Mon Sep 17 00:00:00 2001
From: Alex Deucher <alexdeucher@gmail.com>
Date: Wed, 8 Jul 2009 16:15:30 -0400
Subject: [PATCH 0024/1153] drm/radeon/kms: fix quirk for MSI laptop

The line mux for the connector in the bios tables
is used for enumerating drm connectors.  Since
this laptop has a quirk where the same line much is
listed for both VGA and LVDS, the connectors get
combined.  Setting the line mux on LVDS to an unused
value prevents both encoders from being combined into
the same connector.  This should fix bko bug 13720.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_atombios.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_atombios.c b/drivers/gpu/drm/radeon/radeon_atombios.c
index 1f5a1a49098..fcfe5c02d74 100644
--- a/drivers/gpu/drm/radeon/radeon_atombios.c
+++ b/drivers/gpu/drm/radeon/radeon_atombios.c
@@ -103,7 +103,8 @@ static inline struct radeon_i2c_bus_rec radeon_lookup_gpio(struct drm_device
 static bool radeon_atom_apply_quirks(struct drm_device *dev,
 				     uint32_t supported_device,
 				     int *connector_type,
-				     struct radeon_i2c_bus_rec *i2c_bus)
+				     struct radeon_i2c_bus_rec *i2c_bus,
+				     uint8_t *line_mux)
 {
 
 	/* Asus M2A-VM HDMI board lists the DVI port as HDMI */
@@ -127,8 +128,10 @@ static bool radeon_atom_apply_quirks(struct drm_device *dev,
 	if ((dev->pdev->device == 0x5653) &&
 	    (dev->pdev->subsystem_vendor == 0x1462) &&
 	    (dev->pdev->subsystem_device == 0x0291)) {
-		if (*connector_type == DRM_MODE_CONNECTOR_LVDS)
+		if (*connector_type == DRM_MODE_CONNECTOR_LVDS) {
 			i2c_bus->valid = false;
+			*line_mux = 53;
+		}
 	}
 
 	/* Funky macbooks */
@@ -526,7 +529,7 @@ bool radeon_get_atom_connector_info_from_supported_devices_table(struct
 
 		if (!radeon_atom_apply_quirks
 		    (dev, (1 << i), &bios_connectors[i].connector_type,
-		     &bios_connectors[i].ddc_bus))
+		     &bios_connectors[i].ddc_bus, &bios_connectors[i].line_mux))
 			continue;
 
 		bios_connectors[i].valid = true;
-- 
GitLab


From 2007d633d639c896396e4c4b53b38068f3831307 Mon Sep 17 00:00:00 2001
From: Alex Deucher <alexdeucher@gmail.com>
Date: Wed, 8 Jul 2009 16:17:23 -0400
Subject: [PATCH 0025/1153] drm/radeon/kms: get lvds info for DIG LVTMA and
 UNIPHY encoders
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Noticed by Rafał Miłecki on dri-devel.  On r6xx/r7xx hardware, laptop
panels can be driven by KLDSCP_LVTMA or UNIPHY.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_encoders.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_encoders.c b/drivers/gpu/drm/radeon/radeon_encoders.c
index c8ef0d14ffa..ea15284e758 100644
--- a/drivers/gpu/drm/radeon/radeon_encoders.c
+++ b/drivers/gpu/drm/radeon/radeon_encoders.c
@@ -1700,8 +1700,14 @@ radeon_add_atom_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t su
 	case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_LVTMA:
 	case ENCODER_OBJECT_ID_INTERNAL_UNIPHY1:
 	case ENCODER_OBJECT_ID_INTERNAL_UNIPHY2:
-		drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS);
-		radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder);
+		if (radeon_encoder->devices & (ATOM_DEVICE_LCD_SUPPORT)) {
+			radeon_encoder->rmx_type = RMX_FULL;
+			drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_LVDS);
+			radeon_encoder->enc_priv = radeon_atombios_get_lvds_info(radeon_encoder);
+		} else {
+			drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS);
+			radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder);
+		}
 		drm_encoder_helper_add(encoder, &radeon_atom_dig_helper_funcs);
 		break;
 	}
-- 
GitLab


From e7168cab5bbac0a0e5413fd55ba0e92555bf860d Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Thu, 9 Jul 2009 16:01:42 +1000
Subject: [PATCH 0026/1153] drm/radeon/kms: fix vram vs aper size check.

Fix this to be correct like the DDX code, looks like a typo
on transfer to the kernel.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_device.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c
index f97563db4e5..332911267eb 100644
--- a/drivers/gpu/drm/radeon/radeon_device.c
+++ b/drivers/gpu/drm/radeon/radeon_device.c
@@ -552,7 +552,7 @@ int radeon_device_init(struct radeon_device *rdev,
 	 * for RN50/M6/M7 - Novell bug 204882 ?
 	 */
 	if (rdev->mc.vram_size < rdev->mc.aper_size) {
-		rdev->mc.aper_size = rdev->mc.vram_size;
+		rdev->mc.vram_size = rdev->mc.aper_size;
 	}
 	/* Add an MTRR for the VRAM */
 	rdev->mc.vram_mtrr = mtrr_add(rdev->mc.aper_base, rdev->mc.aper_size,
-- 
GitLab


From 5176fdc4c5873e52f9cb6e166d80e843847e7eb4 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Tue, 30 Jun 2009 11:47:14 +1000
Subject: [PATCH 0027/1153] drm/radeon/kms: drop zero length CS indirect
 buffers.

If userspace sends a zero length IB, it really shouldn't have bothered
so EINVAL it.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_cs.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/radeon_cs.c b/drivers/gpu/drm/radeon/radeon_cs.c
index b843f9bdfb1..a169067efc4 100644
--- a/drivers/gpu/drm/radeon/radeon_cs.c
+++ b/drivers/gpu/drm/radeon/radeon_cs.c
@@ -127,17 +127,23 @@ int radeon_cs_parser_init(struct radeon_cs_parser *p, void *data)
 				       sizeof(struct drm_radeon_cs_chunk))) {
 			return -EFAULT;
 		}
+		p->chunks[i].length_dw = user_chunk.length_dw;
+		p->chunks[i].kdata = NULL;
 		p->chunks[i].chunk_id = user_chunk.chunk_id;
+
 		if (p->chunks[i].chunk_id == RADEON_CHUNK_ID_RELOCS) {
 			p->chunk_relocs_idx = i;
 		}
 		if (p->chunks[i].chunk_id == RADEON_CHUNK_ID_IB) {
 			p->chunk_ib_idx = i;
+			/* zero length IB isn't useful */
+			if (p->chunks[i].length_dw == 0)
+				return -EINVAL;
 		}
+
 		p->chunks[i].length_dw = user_chunk.length_dw;
 		cdata = (uint32_t *)(unsigned long)user_chunk.chunk_data;
 
-		p->chunks[i].kdata = NULL;
 		size = p->chunks[i].length_dw * sizeof(uint32_t);
 		p->chunks[i].kdata = kzalloc(size, GFP_KERNEL);
 		if (p->chunks[i].kdata == NULL) {
-- 
GitLab


From 77bd36f014bc5a3f28507a4e86a81b2b3d2439c3 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Fri, 10 Jul 2009 09:33:00 +1000
Subject: [PATCH 0028/1153] drm/radeon/kms: don't swap PCIEGART PTEs in VRAM.

On powerpc, since we aren't using any hw swappers, this will
get flipped around by default in hw.

tested on a G5 + rv515.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r300.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c
index 656d9238bb0..6435d659cbd 100644
--- a/drivers/gpu/drm/radeon/r300.c
+++ b/drivers/gpu/drm/radeon/r300.c
@@ -154,7 +154,10 @@ int rv370_pcie_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr)
 	addr = (lower_32_bits(addr) >> 8) |
 	       ((upper_32_bits(addr) & 0xff) << 24) |
 	       0xc;
-	writel(cpu_to_le32(addr), ((void __iomem *)ptr) + (i * 4));
+	/* on x86 we want this to be CPU endian, on powerpc
+	 * on powerpc without HW swappers, it'll get swapped on way
+	 * into VRAM - so no need for cpu_to_le32 on VRAM tables */
+	writel(addr, ((void __iomem *)ptr) + (i * 4));
 	return 0;
 }
 
-- 
GitLab


From 61b576dbbe6a19d102c025ebc102a0749e2d3c80 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Michel=20D=C3=A4nzer?= <daenzer@vmware.com>
Date: Wed, 24 Jun 2009 00:12:55 +1000
Subject: [PATCH 0029/1153] drm/radeon: Endianness fixes for radeondrmfb.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

For now handle it via r/g/b offsets and disallow 16 bpp modes on big endian
machines.

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_fb.c | 53 ++++++++++++++++++++++++++++--
 1 file changed, 50 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c
index 9e8f191eb64..260870a29d8 100644
--- a/drivers/gpu/drm/radeon/radeon_fb.c
+++ b/drivers/gpu/drm/radeon/radeon_fb.c
@@ -101,9 +101,10 @@ static int radeonfb_setcolreg(unsigned regno,
 				break;
 			case 24:
 			case 32:
-				fb->pseudo_palette[regno] = ((red & 0xff00) << 8) |
-					(green & 0xff00) |
-					((blue  & 0xff00) >> 8);
+				fb->pseudo_palette[regno] =
+					(((red >> 8) & 0xff) << info->var.red.offset) |
+					(((green >> 8) & 0xff) << info->var.green.offset) |
+					(((blue >> 8) & 0xff) << info->var.blue.offset);
 				break;
 			}
 		}
@@ -154,6 +155,7 @@ static int radeonfb_check_var(struct fb_var_screeninfo *var,
 		var->transp.length = 0;
 		var->transp.offset = 0;
 		break;
+#ifdef __LITTLE_ENDIAN
 	case 15:
 		var->red.offset = 10;
 		var->green.offset = 5;
@@ -194,6 +196,28 @@ static int radeonfb_check_var(struct fb_var_screeninfo *var,
 		var->transp.length = 8;
 		var->transp.offset = 24;
 		break;
+#else
+	case 24:
+		var->red.offset = 8;
+		var->green.offset = 16;
+		var->blue.offset = 24;
+		var->red.length = 8;
+		var->green.length = 8;
+		var->blue.length = 8;
+		var->transp.length = 0;
+		var->transp.offset = 0;
+		break;
+	case 32:
+		var->red.offset = 8;
+		var->green.offset = 16;
+		var->blue.offset = 24;
+		var->red.length = 8;
+		var->green.length = 8;
+		var->blue.length = 8;
+		var->transp.length = 8;
+		var->transp.offset = 0;
+		break;
+#endif
 	default:
 		return -EINVAL;
 	}
@@ -600,6 +624,7 @@ int radeonfb_create(struct radeon_device *rdev,
 		info->var.transp.offset = 0;
 		info->var.transp.length = 0;
 		break;
+#ifdef __LITTLE_ENDIAN
 	case 15:
 		info->var.red.offset = 10;
 		info->var.green.offset = 5;
@@ -639,7 +664,29 @@ int radeonfb_create(struct radeon_device *rdev,
 		info->var.transp.offset = 24;
 		info->var.transp.length = 8;
 		break;
+#else
+	case 24:
+		info->var.red.offset = 8;
+		info->var.green.offset = 16;
+		info->var.blue.offset = 24;
+		info->var.red.length = 8;
+		info->var.green.length = 8;
+		info->var.blue.length = 8;
+		info->var.transp.offset = 0;
+		info->var.transp.length = 0;
+		break;
+	case 32:
+		info->var.red.offset = 8;
+		info->var.green.offset = 16;
+		info->var.blue.offset = 24;
+		info->var.red.length = 8;
+		info->var.green.length = 8;
+		info->var.blue.length = 8;
+		info->var.transp.offset = 0;
+		info->var.transp.length = 8;
+		break;
 	default:
+#endif
 		break;
 	}
 
-- 
GitLab


From ad49f501867cba87e1e45e5ebae0b12435d68bf1 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@linux.ie>
Date: Fri, 10 Jul 2009 22:36:26 +1000
Subject: [PATCH 0030/1153] drm/ttm/radeon: add dma32 support.

This add support for using dma32 memory on gpus that really need it.

Currently IGPs are left without DMA32 but we might need to change
that unless we can fix rs690.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon.h        |  1 +
 drivers/gpu/drm/radeon/radeon_device.c | 17 +++++++++++++++--
 drivers/gpu/drm/radeon/radeon_ttm.c    |  3 ++-
 drivers/gpu/drm/ttm/ttm_bo.c           |  7 ++++++-
 drivers/gpu/drm/ttm/ttm_tt.c           |  9 +++++++--
 include/drm/ttm/ttm_bo_driver.h        |  5 ++++-
 6 files changed, 35 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index e7662ba9abf..3060ce14071 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -624,6 +624,7 @@ struct radeon_device {
 	bool				gpu_lockup;
 	bool				shutdown;
 	bool				suspend;
+	bool				need_dma32;
 };
 
 int radeon_device_init(struct radeon_device *rdev,
diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c
index 332911267eb..27a5ac96995 100644
--- a/drivers/gpu/drm/radeon/radeon_device.c
+++ b/drivers/gpu/drm/radeon/radeon_device.c
@@ -450,6 +450,7 @@ int radeon_device_init(struct radeon_device *rdev,
 		       uint32_t flags)
 {
 	int r, ret;
+	int dma_bits;
 
 	DRM_INFO("radeon: Initializing kernel modesetting.\n");
 	rdev->shutdown = false;
@@ -492,8 +493,20 @@ int radeon_device_init(struct radeon_device *rdev,
 		return r;
 	}
 
-	/* Report DMA addressing limitation */
-	r = pci_set_dma_mask(rdev->pdev, DMA_BIT_MASK(32));
+	/* set DMA mask + need_dma32 flags.
+	 * PCIE - can handle 40-bits.
+	 * IGP - can handle 40-bits (in theory)
+	 * AGP - generally dma32 is safest
+	 * PCI - only dma32
+	 */
+	rdev->need_dma32 = false;
+	if (rdev->flags & RADEON_IS_AGP)
+		rdev->need_dma32 = true;
+	if (rdev->flags & RADEON_IS_PCI)
+		rdev->need_dma32 = true;
+
+	dma_bits = rdev->need_dma32 ? 32 : 40;
+	r = pci_set_dma_mask(rdev->pdev, DMA_BIT_MASK(dma_bits));
 	if (r) {
 		printk(KERN_WARNING "radeon: No suitable DMA available.\n");
 	}
diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c
index 1227a97f516..4ca9aa9203d 100644
--- a/drivers/gpu/drm/radeon/radeon_ttm.c
+++ b/drivers/gpu/drm/radeon/radeon_ttm.c
@@ -442,7 +442,8 @@ int radeon_ttm_init(struct radeon_device *rdev)
 	/* No others user of address space so set it to 0 */
 	r = ttm_bo_device_init(&rdev->mman.bdev,
 			       rdev->mman.mem_global_ref.object,
-			       &radeon_bo_driver, DRM_FILE_PAGE_OFFSET);
+			       &radeon_bo_driver, DRM_FILE_PAGE_OFFSET,
+			       rdev->need_dma32);
 	if (r) {
 		DRM_ERROR("failed initializing buffer object driver(%d).\n", r);
 		return r;
diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c
index a753598a5e3..e55e7972c89 100644
--- a/drivers/gpu/drm/ttm/ttm_bo.c
+++ b/drivers/gpu/drm/ttm/ttm_bo.c
@@ -224,6 +224,9 @@ static int ttm_bo_add_ttm(struct ttm_buffer_object *bo, bool zero_alloc)
 	TTM_ASSERT_LOCKED(&bo->mutex);
 	bo->ttm = NULL;
 
+	if (bdev->need_dma32)
+		page_flags |= TTM_PAGE_FLAG_DMA32;
+
 	switch (bo->type) {
 	case ttm_bo_type_device:
 		if (zero_alloc)
@@ -1332,7 +1335,8 @@ EXPORT_SYMBOL(ttm_bo_device_release);
 
 int ttm_bo_device_init(struct ttm_bo_device *bdev,
 		       struct ttm_mem_global *mem_glob,
-		       struct ttm_bo_driver *driver, uint64_t file_page_offset)
+		       struct ttm_bo_driver *driver, uint64_t file_page_offset,
+		       bool need_dma32)
 {
 	int ret = -EINVAL;
 
@@ -1369,6 +1373,7 @@ int ttm_bo_device_init(struct ttm_bo_device *bdev,
 	INIT_LIST_HEAD(&bdev->ddestroy);
 	INIT_LIST_HEAD(&bdev->swap_lru);
 	bdev->dev_mapping = NULL;
+	bdev->need_dma32 = need_dma32;
 	ttm_mem_init_shrink(&bdev->shrink, ttm_bo_swapout);
 	ret = ttm_mem_register_shrink(mem_glob, &bdev->shrink);
 	if (unlikely(ret != 0)) {
diff --git a/drivers/gpu/drm/ttm/ttm_tt.c b/drivers/gpu/drm/ttm/ttm_tt.c
index 75dc8bd2459..81ab81f030a 100644
--- a/drivers/gpu/drm/ttm/ttm_tt.c
+++ b/drivers/gpu/drm/ttm/ttm_tt.c
@@ -131,10 +131,15 @@ static void ttm_tt_free_page_directory(struct ttm_tt *ttm)
 
 static struct page *ttm_tt_alloc_page(unsigned page_flags)
 {
+	gfp_t gfp_flags = GFP_HIGHUSER;
+
 	if (page_flags & TTM_PAGE_FLAG_ZERO_ALLOC)
-		return alloc_page(GFP_HIGHUSER | __GFP_ZERO);
+		gfp_flags |= __GFP_ZERO;
+
+	if (page_flags & TTM_PAGE_FLAG_DMA32)
+		gfp_flags |= __GFP_DMA32;
 
-	return alloc_page(GFP_HIGHUSER);
+	return alloc_page(gfp_flags);
 }
 
 static void ttm_tt_free_user_pages(struct ttm_tt *ttm)
diff --git a/include/drm/ttm/ttm_bo_driver.h b/include/drm/ttm/ttm_bo_driver.h
index 62ed733c52a..ea83dd23a4d 100644
--- a/include/drm/ttm/ttm_bo_driver.h
+++ b/include/drm/ttm/ttm_bo_driver.h
@@ -121,6 +121,7 @@ struct ttm_backend {
 #define TTM_PAGE_FLAG_SWAPPED         (1 << 4)
 #define TTM_PAGE_FLAG_PERSISTANT_SWAP (1 << 5)
 #define TTM_PAGE_FLAG_ZERO_ALLOC      (1 << 6)
+#define TTM_PAGE_FLAG_DMA32           (1 << 7)
 
 enum ttm_caching_state {
 	tt_uncached,
@@ -429,6 +430,8 @@ struct ttm_bo_device {
 	 */
 
 	struct delayed_work wq;
+
+	bool need_dma32;
 };
 
 /**
@@ -648,7 +651,7 @@ extern int ttm_bo_device_release(struct ttm_bo_device *bdev);
 extern int ttm_bo_device_init(struct ttm_bo_device *bdev,
 			      struct ttm_mem_global *mem_glob,
 			      struct ttm_bo_driver *driver,
-			      uint64_t file_page_offset);
+			      uint64_t file_page_offset, bool need_dma32);
 
 /**
  * ttm_bo_reserve:
-- 
GitLab


From 2a0f8918fc34713ecaeb900ffb9afa61df4cb08e Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@linux.ie>
Date: Sat, 11 Jul 2009 04:44:47 +1000
Subject: [PATCH 0031/1153] drm/radeon/kms: fix VRAM sizing like DDX does it.

Doing this like the DDX seems like the most sure fire way to avoid
having to reinvent it slowly and painfully. At the moment we keep
getting things wrong with aper vs vram, so we know the DDX does it right.

booted on PCI r100, PCIE rv370, IGP rs400.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r100.c          | 65 +++++++++++++++++++++++++-
 drivers/gpu/drm/radeon/r300.c          |  4 +-
 drivers/gpu/drm/radeon/r520.c          |  4 +-
 drivers/gpu/drm/radeon/radeon.h        |  2 +
 drivers/gpu/drm/radeon/radeon_device.c |  7 +--
 drivers/gpu/drm/radeon/rs400.c         | 14 +-----
 drivers/gpu/drm/radeon/rv515.c         |  6 +--
 7 files changed, 71 insertions(+), 31 deletions(-)

diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index 154648a2c02..97c9229b929 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -1360,9 +1360,50 @@ static void r100_vram_get_type(struct radeon_device *rdev)
 	}
 }
 
-void r100_vram_info(struct radeon_device *rdev)
+static u32 r100_get_accessible_vram(struct radeon_device *rdev)
 {
-	r100_vram_get_type(rdev);
+	u32 aper_size;
+	u8 byte;
+
+	aper_size = RREG32(RADEON_CONFIG_APER_SIZE);
+
+	/* Set HDP_APER_CNTL only on cards that are known not to be broken,
+	 * that is has the 2nd generation multifunction PCI interface
+	 */
+	if (rdev->family == CHIP_RV280 ||
+	    rdev->family >= CHIP_RV350) {
+		WREG32_P(RADEON_HOST_PATH_CNTL, RADEON_HDP_APER_CNTL,
+		       ~RADEON_HDP_APER_CNTL);
+		DRM_INFO("Generation 2 PCI interface, using max accessible memory\n");
+		return aper_size * 2;
+	}
+
+	/* Older cards have all sorts of funny issues to deal with. First
+	 * check if it's a multifunction card by reading the PCI config
+	 * header type... Limit those to one aperture size
+	 */
+	pci_read_config_byte(rdev->pdev, 0xe, &byte);
+	if (byte & 0x80) {
+		DRM_INFO("Generation 1 PCI interface in multifunction mode\n");
+		DRM_INFO("Limiting VRAM to one aperture\n");
+		return aper_size;
+	}
+
+	/* Single function older card. We read HDP_APER_CNTL to see how the BIOS
+	 * have set it up. We don't write this as it's broken on some ASICs but
+	 * we expect the BIOS to have done the right thing (might be too optimistic...)
+	 */
+	if (RREG32(RADEON_HOST_PATH_CNTL) & RADEON_HDP_APER_CNTL)
+		return aper_size * 2;
+	return aper_size;
+}
+
+void r100_vram_init_sizes(struct radeon_device *rdev)
+{
+	u64 config_aper_size;
+	u32 accessible;
+
+	config_aper_size = RREG32(RADEON_CONFIG_APER_SIZE);
 
 	if (rdev->flags & RADEON_IS_IGP) {
 		uint32_t tom;
@@ -1383,10 +1424,30 @@ void r100_vram_info(struct radeon_device *rdev)
 		}
 		/* let driver place VRAM */
 		rdev->mc.vram_location = 0xFFFFFFFFUL;
+		 /* Fix for RN50, M6, M7 with 8/16/32(??) MBs of VRAM - 
+		  * Novell bug 204882 + along with lots of ubuntu ones */
+		if (config_aper_size > rdev->mc.vram_size)
+			rdev->mc.vram_size = config_aper_size;
 	}
 
+	/* work out accessible VRAM */
+	accessible = r100_get_accessible_vram(rdev);
+
 	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
 	rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0);
+
+	if (accessible > rdev->mc.aper_size)
+		accessible = rdev->mc.aper_size;
+
+	if (rdev->mc.vram_size > rdev->mc.aper_size)
+		rdev->mc.vram_size = rdev->mc.aper_size;
+}
+
+void r100_vram_info(struct radeon_device *rdev)
+{
+	r100_vram_get_type(rdev);
+
+	r100_vram_init_sizes(rdev);
 }
 
 
diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c
index 6435d659cbd..0e0e094da50 100644
--- a/drivers/gpu/drm/radeon/r300.c
+++ b/drivers/gpu/drm/radeon/r300.c
@@ -585,10 +585,8 @@ void r300_vram_info(struct radeon_device *rdev)
 	} else {
 		rdev->mc.vram_width = 64;
 	}
-	rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE);
 
-	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
-	rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0);
+	r100_vram_init_sizes(rdev);
 }
 
 
diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c
index 570a244bd88..b6bd3758db6 100644
--- a/drivers/gpu/drm/radeon/r520.c
+++ b/drivers/gpu/drm/radeon/r520.c
@@ -227,8 +227,6 @@ static void r520_vram_get_type(struct radeon_device *rdev)
 void r520_vram_info(struct radeon_device *rdev)
 {
 	r520_vram_get_type(rdev);
-	rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE);
 
-	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
-	rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0);
+	r100_vram_init_sizes(rdev);
 }
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index 3060ce14071..248e3341a98 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -541,6 +541,8 @@ union radeon_asic_config {
 	struct r300_asic	r300;
 };
 
+/* r100 */
+void r100_vram_init_sizes(struct radeon_device *rdev);
 
 /*
  * IOCTL.
diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c
index 27a5ac96995..cdef6eb01ba 100644
--- a/drivers/gpu/drm/radeon/radeon_device.c
+++ b/drivers/gpu/drm/radeon/radeon_device.c
@@ -561,12 +561,7 @@ int radeon_device_init(struct radeon_device *rdev,
 	}
 	/* Get vram informations */
 	radeon_vram_info(rdev);
-	/* Device is severly broken if aper size > vram size.
-	 * for RN50/M6/M7 - Novell bug 204882 ?
-	 */
-	if (rdev->mc.vram_size < rdev->mc.aper_size) {
-		rdev->mc.vram_size = rdev->mc.aper_size;
-	}
+
 	/* Add an MTRR for the VRAM */
 	rdev->mc.vram_mtrr = mtrr_add(rdev->mc.aper_base, rdev->mc.aper_size,
 				      MTRR_TYPE_WRCOMB, 1);
diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c
index a18d053065c..daf24e85cba 100644
--- a/drivers/gpu/drm/radeon/rs400.c
+++ b/drivers/gpu/drm/radeon/rs400.c
@@ -292,24 +292,12 @@ void rs400_gpu_init(struct radeon_device *rdev)
  */
 void rs400_vram_info(struct radeon_device *rdev)
 {
-	uint32_t tom;
-
 	rs400_gart_adjust_size(rdev);
 	/* DDR for all card after R300 & IGP */
 	rdev->mc.vram_is_ddr = true;
 	rdev->mc.vram_width = 128;
 
-	/* read NB_TOM to get the amount of ram stolen for the GPU */
-	tom = RREG32(RADEON_NB_TOM);
-	rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16);
-	WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size);
-
-	/* RS480 IGPs don't seem to translate to main RAM, they
-	 * just reserve and scan out of it. So setting VRAM location
-	 * to say 0, will actually trash the OS. */
-	rdev->mc.vram_location = (tom & 0xffff) << 16;
-	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
-	rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0);
+	r100_vram_init_sizes(rdev);
 }
 
 
diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c
index d1384d3991a..677929ed8ed 100644
--- a/drivers/gpu/drm/radeon/rv515.c
+++ b/drivers/gpu/drm/radeon/rv515.c
@@ -395,10 +395,8 @@ static void rv515_vram_get_type(struct radeon_device *rdev)
 void rv515_vram_info(struct radeon_device *rdev)
 {
 	rv515_vram_get_type(rdev);
-	rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE);
-
-	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
-	rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0);
+	
+	r100_vram_init_sizes(rdev);
 }
 
 
-- 
GitLab


From b995e4330de0d8b1b8b9e49ce10cc6dc78e2cbba Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@linux.ie>
Date: Tue, 14 Jul 2009 02:02:32 +1000
Subject: [PATCH 0032/1153] drm/radeon/kms: block RN50 from using 3D engine.

RN50/ES1000 is a cut-down rv100 chip used in the server market.
The 3D engine on these is either not there or unverified so refuse
any attempt to configure registers on it.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r100.c   | 5 +++++
 drivers/gpu/drm/radeon/radeon.h | 2 ++
 2 files changed, 7 insertions(+)

diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index 97c9229b929..0d05909f03f 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -973,6 +973,11 @@ static int r100_packet0_check(struct radeon_cs_parser *p,
 		case R300_TX_OFFSET_0+52:
 		case R300_TX_OFFSET_0+56:
 		case R300_TX_OFFSET_0+60:
+			/* rn50 has no 3D engine so fail on any 3d setup */
+			if (ASIC_IS_RN50(p->rdev)) {
+				DRM_ERROR("attempt to use RN50 3D engine failed\n");
+				return -EINVAL;
+			}
 			r = r100_cs_packet_next_reloc(p, &reloc);
 			if (r) {
 				DRM_ERROR("No reloc for ib[%d]=0x%04X\n",
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index 248e3341a98..7f007185e7f 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -673,6 +673,8 @@ void r100_pll_errata_after_index(struct radeon_device *rdev);
 /*
  * ASICs helpers.
  */
+#define ASIC_IS_RN50(rdev) ((rdev->pdev->device == 0x515e) || \
+			    (rdev->pdev->device == 0x5969))
 #define ASIC_IS_RV100(rdev) ((rdev->family == CHIP_RV100) || \
 		(rdev->family == CHIP_RV200) || \
 		(rdev->family == CHIP_RS100) || \
-- 
GitLab


From d0e275a90a81b37409a0cfbca77581e3d235f5cf Mon Sep 17 00:00:00 2001
From: Alex Deucher <alexdeucher@gmail.com>
Date: Mon, 13 Jul 2009 11:08:18 -0400
Subject: [PATCH 0033/1153] drm/radeon/kms: add PLL flag to prefer frequencies
 <= the target freq

This is needed when using fractional feedback dividers on some IGP
chips.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_display.c | 6 +++++-
 drivers/gpu/drm/radeon/radeon_mode.h    | 1 +
 2 files changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/radeon_display.c b/drivers/gpu/drm/radeon/radeon_display.c
index 3efcf1a526b..bc312f3d9a0 100644
--- a/drivers/gpu/drm/radeon/radeon_display.c
+++ b/drivers/gpu/drm/radeon/radeon_display.c
@@ -491,7 +491,11 @@ void radeon_compute_pll(struct radeon_pll *pll,
 					tmp += (uint64_t)pll->reference_freq * 1000 * frac_feedback_div;
 					current_freq = radeon_div(tmp, ref_div * post_div);
 
-					error = abs(current_freq - freq);
+					if (flags & RADEON_PLL_PREFER_CLOSEST_LOWER) {
+						error = freq - current_freq;
+						error = error < 0 ? 0xffffffff : error;
+					} else
+						error = abs(current_freq - freq);
 					vco_diff = abs(vco - best_vco);
 
 					if ((best_vco == 0 && error < best_error) ||
diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h
index 86f766e868e..38c1dd08244 100644
--- a/drivers/gpu/drm/radeon/radeon_mode.h
+++ b/drivers/gpu/drm/radeon/radeon_mode.h
@@ -124,6 +124,7 @@ struct radeon_tmds_pll {
 #define RADEON_PLL_PREFER_LOW_POST_DIV  (1 << 8)
 #define RADEON_PLL_PREFER_HIGH_POST_DIV (1 << 9)
 #define RADEON_PLL_USE_FRAC_FB_DIV      (1 << 10)
+#define RADEON_PLL_PREFER_CLOSEST_LOWER (1 << 11)
 
 struct radeon_pll {
 	uint16_t reference_freq;
-- 
GitLab


From eb1300bcd70b3bffbefb6ae0eab13a571255ee93 Mon Sep 17 00:00:00 2001
From: Alex Deucher <alexdeucher@gmail.com>
Date: Mon, 13 Jul 2009 11:09:56 -0400
Subject: [PATCH 0034/1153] drm/radeon/kms: enable frac fb divs on
 rs600/rs690/rs740

Allows us to hit dot clocks much closer, especially on
chips with non-27 Mhz reference clocks like most IGP chips.
This fixes most flickering and blanking problems with
non-exact dot clocks on these chips.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/atombios_crtc.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c
index c0080cc9bf8..e64a199b5ee 100644
--- a/drivers/gpu/drm/radeon/atombios_crtc.c
+++ b/drivers/gpu/drm/radeon/atombios_crtc.c
@@ -203,6 +203,12 @@ void atombios_crtc_set_pll(struct drm_crtc *crtc, struct drm_display_mode *mode)
 	if (ASIC_IS_AVIVO(rdev)) {
 		uint32_t ss_cntl;
 
+		if ((rdev->family == CHIP_RS600) ||
+		    (rdev->family == CHIP_RS690) ||
+		    (rdev->family == CHIP_RS740))
+			pll_flags |= (RADEON_PLL_USE_FRAC_FB_DIV |
+				      RADEON_PLL_PREFER_CLOSEST_LOWER);
+
 		if (ASIC_IS_DCE32(rdev) && mode->clock > 200000)	/* range limits??? */
 			pll_flags |= RADEON_PLL_PREFER_HIGH_FB_DIV;
 		else
-- 
GitLab


From c836e862803b2aa2bd9a354e151316d2b42c44ec Mon Sep 17 00:00:00 2001
From: Alex Deucher <alexdeucher@gmail.com>
Date: Mon, 13 Jul 2009 13:51:03 -0400
Subject: [PATCH 0035/1153] drm/radeon/kms: fix hotspot handling on pre-avivo
 chips

Need to adjust CUR_OFFSET for yorigin

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_cursor.c | 9 +++++++--
 drivers/gpu/drm/radeon/radeon_mode.h   | 1 +
 2 files changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_cursor.c b/drivers/gpu/drm/radeon/radeon_cursor.c
index 5f8ce370c4f..b13c79e38bc 100644
--- a/drivers/gpu/drm/radeon/radeon_cursor.c
+++ b/drivers/gpu/drm/radeon/radeon_cursor.c
@@ -111,9 +111,11 @@ static void radeon_set_cursor(struct drm_crtc *crtc, struct drm_gem_object *obj,
 
 	if (ASIC_IS_AVIVO(rdev))
 		WREG32(AVIVO_D1CUR_SURFACE_ADDRESS + radeon_crtc->crtc_offset, gpu_addr);
-	else
+	else {
+		radeon_crtc->legacy_cursor_offset = gpu_addr - radeon_crtc->legacy_display_base_addr;
 		/* offset is from DISP(2)_BASE_ADDRESS */
-		WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, (gpu_addr-radeon_crtc->legacy_display_base_addr));
+		WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, radeon_crtc->legacy_cursor_offset);
+	}
 }
 
 int radeon_crtc_cursor_set(struct drm_crtc *crtc,
@@ -245,6 +247,9 @@ int radeon_crtc_cursor_move(struct drm_crtc *crtc,
 		       (RADEON_CUR_LOCK
 			| ((xorigin ? 0 : x) << 16)
 			| (yorigin ? 0 : y)));
+		/* offset is from DISP(2)_BASE_ADDRESS */
+		WREG32(RADEON_CUR_OFFSET + radeon_crtc->crtc_offset, (radeon_crtc->legacy_cursor_offset +
+								      (yorigin * 256)));
 	}
 	radeon_lock_cursor(crtc, false);
 
diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h
index 38c1dd08244..ba89b59f6e5 100644
--- a/drivers/gpu/drm/radeon/radeon_mode.h
+++ b/drivers/gpu/drm/radeon/radeon_mode.h
@@ -187,6 +187,7 @@ struct radeon_crtc {
 	int cursor_width;
 	int cursor_height;
 	uint32_t legacy_display_base_addr;
+	uint32_t legacy_cursor_offset;
 };
 
 #define RADEON_USE_RMX 1
-- 
GitLab


From 5381837f125cc62ad703fbcdfcd7566fc81fd404 Mon Sep 17 00:00:00 2001
From: Tom Peng <tom_peng@usish.com>
Date: Wed, 1 Jul 2009 20:37:26 +0800
Subject: [PATCH 0036/1153] [SCSI] libsas: reuse the original port when
 hotplugging phys in wide ports

There's a hotplug problem in the way libsas allocates ports: it loops over the
available ports first trying to add to an existing for a wide port and
otherwise allocating the next free port.  This scheme only works if the port
array is packed from zero, which fails if a port gets hot unplugged and the
array becomes sparse.  In that case, a new port is formed even if there's a
wide port it should be part of.  Fix this by creating two loops over all the
ports:  the first to see if the phy should be part of a wide port and the
second to form a new port in an empty port slot.

Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/scsi/libsas/sas_port.c | 19 +++++++++++++++----
 1 file changed, 15 insertions(+), 4 deletions(-)

diff --git a/drivers/scsi/libsas/sas_port.c b/drivers/scsi/libsas/sas_port.c
index e6ac59c023f..fe8b74c706d 100644
--- a/drivers/scsi/libsas/sas_port.c
+++ b/drivers/scsi/libsas/sas_port.c
@@ -56,7 +56,7 @@ static void sas_form_port(struct asd_sas_phy *phy)
 		}
 	}
 
-	/* find a port */
+	/* see if the phy should be part of a wide port */
 	spin_lock_irqsave(&sas_ha->phy_port_lock, flags);
 	for (i = 0; i < sas_ha->num_phys; i++) {
 		port = sas_ha->sas_port[i];
@@ -69,12 +69,23 @@ static void sas_form_port(struct asd_sas_phy *phy)
 			SAS_DPRINTK("phy%d matched wide port%d\n", phy->id,
 				    port->id);
 			break;
-		} else if (*(u64 *) port->sas_addr == 0 && port->num_phys==0) {
-			memcpy(port->sas_addr, phy->sas_addr, SAS_ADDR_SIZE);
-			break;
 		}
 		spin_unlock(&port->phy_list_lock);
 	}
+	/* The phy does not match any existing port, create a new one */
+	if (i == sas_ha->num_phys) {
+		for (i = 0; i < sas_ha->num_phys; i++) {
+			port = sas_ha->sas_port[i];
+			spin_lock(&port->phy_list_lock);
+			if (*(u64 *)port->sas_addr == 0
+				&& port->num_phys == 0) {
+				memcpy(port->sas_addr, phy->sas_addr,
+					SAS_ADDR_SIZE);
+				break;
+			}
+			spin_unlock(&port->phy_list_lock);
+		}
+	}
 
 	if (i >= sas_ha->num_phys) {
 		printk(KERN_NOTICE "%s: couldn't find a free port, bug?\n",
-- 
GitLab


From 390c4dd448b1a5f04ea497c20f5ff664f8eeed01 Mon Sep 17 00:00:00 2001
From: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu, 16 Jul 2009 13:01:01 -0700
Subject: [PATCH 0037/1153] drm/i915: handle FIFO oversubsription correctly

If you're pushing a plane hard (i.e. you need most or all of the FIFO
entries just to cover your frame refresh latency), the watermark level
may end up being negative.  So fix up the signed vs. unsigned math in
the calculation function to handle this correctly, giving all available
FIFO entries to such a configuration.

Reported-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_display.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 3fa0d63c83b..890f7108e72 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -1674,7 +1674,7 @@ static unsigned long intel_calculate_wm(unsigned long clock_in_khz,
 					int pixel_size,
 					unsigned long latency_ns)
 {
-	unsigned long entries_required, wm_size;
+	long entries_required, wm_size;
 
 	entries_required = (clock_in_khz * pixel_size * latency_ns) / 1000000;
 	entries_required /= wm->cacheline_size;
@@ -1685,9 +1685,10 @@ static unsigned long intel_calculate_wm(unsigned long clock_in_khz,
 
 	DRM_DEBUG("FIFO watermark level: %d\n", wm_size);
 
-	if (wm_size > wm->max_wm)
+	/* Don't promote wm_size to unsigned... */
+	if (wm_size > (long)wm->max_wm)
 		wm_size = wm->max_wm;
-	if (wm_size == 0)
+	if (wm_size <= 0)
 		wm_size = wm->default_wm;
 	return wm_size;
 }
-- 
GitLab


From 2a2430f4542467502d39660bfd66b0004fd8d6a9 Mon Sep 17 00:00:00 2001
From: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu, 16 Jul 2009 13:01:02 -0700
Subject: [PATCH 0038/1153] drm/i915: correct self-refresh calculation in
 "everything off" case

If no planes are enabled, the self-refresh calculation may end up doing
a divide by zero.  This patch should prevent that by making sure at
least one of the CRTCs had a valid hdisplay value.

Reported-by: Eric Anholt <eric@anholt.net>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_display.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 890f7108e72..a58bfadabd6 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -1906,7 +1906,7 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock,
 	cwm = 2;
 
 	/* Calc sr entries for one plane configs */
-	if (!planea_clock || !planeb_clock) {
+	if (sr_hdisplay && (!planea_clock || !planeb_clock)) {
 		/* self-refresh has much higher latency */
 		const static int sr_latency_ns = 6000;
 
@@ -1921,6 +1921,8 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock,
 		srwm = total_size - sr_entries;
 		if (srwm < 0)
 			srwm = 1;
+		if (IS_I9XX(dev))
+			I915_WRITE(FW_BLC_SELF, (srwm & 0x3f));
 	}
 
 	DRM_DEBUG("Setting FIFO watermarks - A: %d, B: %d, C: %d, SR %d\n",
@@ -1935,8 +1937,6 @@ static void i9xx_update_wm(struct drm_device *dev, int planea_clock,
 
 	I915_WRITE(FW_BLC, fwater_lo);
 	I915_WRITE(FW_BLC2, fwater_hi);
-	if (IS_I9XX(dev))
-		I915_WRITE(FW_BLC_SELF, (srwm & 0x3f));
 }
 
 static void i830_update_wm(struct drm_device *dev, int planea_clock,
-- 
GitLab


From 14d87e6c399f3942d63dff41447ff08a615d9a6b Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Fri, 17 Jul 2009 10:28:19 -0700
Subject: [PATCH 0039/1153] sparc: Fix cleanup crash in bbc_envctrl_cleanup()
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

If kthread_run() fails or never gets to run we'll have NULL
or a pointer encoded error in kenvctrld_task, rather than
a legitimate task pointer.

So this makes bbc_envctrl_cleanup() crash as it passed this
bogus pointer into kthread_stop().

Reported-by: BERTRAND Joël <joel.bertrand@systella.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/sbus/char/bbc_envctrl.c | 11 ++++++++---
 1 file changed, 8 insertions(+), 3 deletions(-)

diff --git a/drivers/sbus/char/bbc_envctrl.c b/drivers/sbus/char/bbc_envctrl.c
index 15dab96d05e..7c815d3327f 100644
--- a/drivers/sbus/char/bbc_envctrl.c
+++ b/drivers/sbus/char/bbc_envctrl.c
@@ -537,8 +537,12 @@ int bbc_envctrl_init(struct bbc_i2c_bus *bp)
 	}
 	if (temp_index != 0 && fan_index != 0) {
 		kenvctrld_task = kthread_run(kenvctrld, NULL, "kenvctrld");
-		if (IS_ERR(kenvctrld_task))
-			return PTR_ERR(kenvctrld_task);
+		if (IS_ERR(kenvctrld_task)) {
+			int err = PTR_ERR(kenvctrld_task);
+
+			kenvctrld_task = NULL;
+			return err;
+		}
 	}
 
 	return 0;
@@ -561,7 +565,8 @@ void bbc_envctrl_cleanup(struct bbc_i2c_bus *bp)
 	struct bbc_cpu_temperature *tp, *tpos;
 	struct bbc_fan_control *fp, *fpos;
 
-	kthread_stop(kenvctrld_task);
+	if (kenvctrld_task)
+		kthread_stop(kenvctrld_task);
 
 	list_for_each_entry_safe(tp, tpos, &bp->temps, bp_list) {
 		list_del(&tp->bp_list);
-- 
GitLab


From eb9069119d1c4bc856b4c1339abcad0105691e71 Mon Sep 17 00:00:00 2001
From: Haojian Zhuang <haojian.zhuang@marvell.com>
Date: Wed, 15 Jul 2009 19:47:24 +0800
Subject: [PATCH 0040/1153] [ARM] pxa: fix gpio issue in zylonite

WARNING: at drivers/gpio/gpiolib.c:83 gpio_ensure_requested+0x58/0xbc()
 autorequest GPIO-71
 Modules linked in:
 [<c0028bd0>] (unwind_backtrace+0x0/0xe8) from [<c003c328>] (warn_slowpath_common+0x48/0x78)
 [<c003c328>] (warn_slowpath_common+0x48/0x78) from [<c003c394>] (warn_slowpath_fmt+0x28/0x38)
 [<c003c394>] (warn_slowpath_fmt+0x28/0x38) from [<c0146128>] (gpio_ensure_requested+0x58/0xbc)
 [<c0146128>] (gpio_ensure_requested+0x58/0xbc) from [<c0146308>] (gpio_direction_input+0x80/0xf4)
 [<c0146308>] (gpio_direction_input+0x80/0xf4) from [<c000c668>] (zylonite_pxa300_init+0x108/0x214)
 [<c000c668>] (zylonite_pxa300_init+0x108/0x214) from [<c000c4e4>] (zylonite_init+0x8/0x84)
 [<c000c4e4>] (zylonite_init+0x8/0x84) from [<c00097cc>] (customize_machine+0x18/0x24)
 [<c00097cc>] (customize_machine+0x18/0x24) from [<c00222e0>] (do_one_initcall+0x30/0x1b0)
 [<c00222e0>] (do_one_initcall+0x30/0x1b0) from [<c00083f4>] (kernel_init+0xa4/0x11c)
 [<c00083f4>] (kernel_init+0xa4/0x11c) from [<c0023f3c>] (kernel_thread_exit+0x0/0x8)
 ---[ end trace 1b75b31a2719ed1c ]---

This issue is caused by using gpio pin without request. Add gpio_request()
into zylonite. To simplify the code, error checking is omitted since this
is being performed early.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
---
 arch/arm/mach-pxa/zylonite_pxa300.c | 2 ++
 arch/arm/mach-pxa/zylonite_pxa320.c | 2 ++
 2 files changed, 4 insertions(+)

diff --git a/arch/arm/mach-pxa/zylonite_pxa300.c b/arch/arm/mach-pxa/zylonite_pxa300.c
index cefd1c0a854..84095440a87 100644
--- a/arch/arm/mach-pxa/zylonite_pxa300.c
+++ b/arch/arm/mach-pxa/zylonite_pxa300.c
@@ -197,10 +197,12 @@ static void __init zylonite_detect_lcd_panel(void)
 	for (i = 0; i < NUM_LCD_DETECT_PINS; i++) {
 		id = id << 1;
 		gpio = mfp_to_gpio(lcd_detect_pins[i]);
+		gpio_request(gpio, "LCD_ID_PINS");
 		gpio_direction_input(gpio);
 
 		if (gpio_get_value(gpio))
 			id = id | 0x1;
+		gpio_free(gpio);
 	}
 
 	/* lcd id, flush out bit 1 */
diff --git a/arch/arm/mach-pxa/zylonite_pxa320.c b/arch/arm/mach-pxa/zylonite_pxa320.c
index cc5a2283360..60d08f23f5e 100644
--- a/arch/arm/mach-pxa/zylonite_pxa320.c
+++ b/arch/arm/mach-pxa/zylonite_pxa320.c
@@ -176,10 +176,12 @@ static void __init zylonite_detect_lcd_panel(void)
 	for (i = 0; i < NUM_LCD_DETECT_PINS; i++) {
 		id = id << 1;
 		gpio = mfp_to_gpio(lcd_detect_pins[i]);
+		gpio_request(gpio, "LCD_ID_PINS");
 		gpio_direction_input(gpio);
 
 		if (gpio_get_value(gpio))
 			id = id | 0x1;
+		gpio_free(gpio);
 	}
 
 	/* lcd id, flush out bit 1 */
-- 
GitLab


From ecf763c5677faee04d47333e6ed8e9539a427770 Mon Sep 17 00:00:00 2001
From: Marek Vasut <marek.vasut@gmail.com>
Date: Thu, 16 Jul 2009 19:37:29 +0200
Subject: [PATCH 0041/1153] [ARM] pxa: add STUART MFP config for PalmTX,T5,LD

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
---
 arch/arm/mach-pxa/palmld.c | 4 ++++
 arch/arm/mach-pxa/palmt5.c | 4 ++++
 arch/arm/mach-pxa/palmtx.c | 4 ++++
 3 files changed, 12 insertions(+)

diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c
index ed70f281dd0..169fcc18154 100644
--- a/arch/arm/mach-pxa/palmld.c
+++ b/arch/arm/mach-pxa/palmld.c
@@ -128,6 +128,10 @@ static unsigned long palmld_pin_config[] __initdata = {
 	GPIO38_GPIO,	/* wifi ready */
 	GPIO81_GPIO,	/* wifi reset */
 
+	/* FFUART */
+	GPIO34_FFUART_RXD,
+	GPIO39_FFUART_TXD,
+
 	/* HDD */
 	GPIO98_GPIO,	/* HDD reset */
 	GPIO115_GPIO,	/* HDD power */
diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c
index aae64a12a73..33f726ff55e 100644
--- a/arch/arm/mach-pxa/palmt5.c
+++ b/arch/arm/mach-pxa/palmt5.c
@@ -111,6 +111,10 @@ static unsigned long palmt5_pin_config[] __initdata = {
 	/* PWM */
 	GPIO16_PWM0_OUT,
 
+	/* FFUART */
+	GPIO34_FFUART_RXD,
+	GPIO39_FFUART_TXD,
+
 	/* MISC */
 	GPIO10_GPIO,	/* hotsync button */
 	GPIO90_GPIO,	/* power detect */
diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c
index 6c15d84bde5..83d02087958 100644
--- a/arch/arm/mach-pxa/palmtx.c
+++ b/arch/arm/mach-pxa/palmtx.c
@@ -127,6 +127,10 @@ static unsigned long palmtx_pin_config[] __initdata = {
 	GPIO76_LCD_PCLK,
 	GPIO77_LCD_BIAS,
 
+	/* FFUART */
+	GPIO34_FFUART_RXD,
+	GPIO39_FFUART_TXD,
+
 	/* MISC. */
 	GPIO10_GPIO,	/* hotsync button */
 	GPIO12_GPIO,	/* power detect */
-- 
GitLab


From e5d490b252423605a77c54b2e35b10ea663763df Mon Sep 17 00:00:00 2001
From: Mel Gorman <mel@csn.ul.ie>
Date: Wed, 15 Jul 2009 12:23:11 +0100
Subject: [PATCH 0042/1153] profile: Suppress warning about large allocations
 when profile=1 is specified

When profile= is used, a large buffer is allocated early at
boot. This can be larger than what the page allocator can
provide so it prints a warning. However, the caller is able to
handle the situation so this patch suppresses the warning.

Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Linux Memory Management List <linux-mm@kvack.org>
Cc: Heinz Diehl <htd@fancy-poultry.org>
Cc: David Miller <davem@davemloft.net>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1247656992-19846-3-git-send-email-mel@csn.ul.ie>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/profile.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/kernel/profile.c b/kernel/profile.c
index 69911b5745e..419250ebec4 100644
--- a/kernel/profile.c
+++ b/kernel/profile.c
@@ -117,11 +117,12 @@ int __ref profile_init(void)
 
 	cpumask_copy(prof_cpu_mask, cpu_possible_mask);
 
-	prof_buffer = kzalloc(buffer_bytes, GFP_KERNEL);
+	prof_buffer = kzalloc(buffer_bytes, GFP_KERNEL|__GFP_NOWARN);
 	if (prof_buffer)
 		return 0;
 
-	prof_buffer = alloc_pages_exact(buffer_bytes, GFP_KERNEL|__GFP_ZERO);
+	prof_buffer = alloc_pages_exact(buffer_bytes,
+					GFP_KERNEL|__GFP_ZERO|__GFP_NOWARN);
 	if (prof_buffer)
 		return 0;
 
-- 
GitLab


From cefcb800fa9536bb6f29485c53e6c82a65b0c022 Mon Sep 17 00:00:00 2001
From: Goldwyn Rodrigues <rgoldwyn@gmail.com>
Date: Sat, 11 Jul 2009 10:57:27 -0500
Subject: [PATCH 0043/1153] ocfs2: Initialize count in aio_write before
 generic_write_checks

generic_write_checks() expects count to be initialized to the size of
the write.  Writes to files open with O_DIRECT|O_LARGEFILE write 0 bytes
because count is uninitialized.

Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/file.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/fs/ocfs2/file.c b/fs/ocfs2/file.c
index a49fa44aea1..aa501d3f93f 100644
--- a/fs/ocfs2/file.c
+++ b/fs/ocfs2/file.c
@@ -1851,6 +1851,7 @@ relock:
 		if (ret)
 			goto out_dio;
 
+		count = ocount;
 		ret = generic_write_checks(file, ppos, &count,
 					   S_ISBLK(inode->i_mode));
 		if (ret)
-- 
GitLab


From 44d8e4e1e9b941065eb7578669fe51eb65c73e63 Mon Sep 17 00:00:00 2001
From: Subrata Modak <subrata@linux.vnet.ibm.com>
Date: Tue, 14 Jul 2009 01:19:31 +0530
Subject: [PATCH 0044/1153] ocfs2: Fix compilation warning for fs/ocfs2/xattr.c
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

gcc 4.4.1 generates the following build warning on i386:

CC [M]  fs/ocfs2/xattr.o
fs/ocfs2/xattr.c: In function ‘ocfs2_xattr_block_get’:
fs/ocfs2/xattr.c:1055: warning: ‘block_off’ may be used uninitialized in this function

The following fix is based on a similar approach by David Howells
few days back: http://lkml.org/lkml/2009/7/9/109,

Signed-off-by: Subrata Modak<subrata@linux.vnet.ibm.com>,
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/xattr.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/fs/ocfs2/xattr.c b/fs/ocfs2/xattr.c
index ba320e25074..d1a27cda984 100644
--- a/fs/ocfs2/xattr.c
+++ b/fs/ocfs2/xattr.c
@@ -1052,7 +1052,8 @@ static int ocfs2_xattr_block_get(struct inode *inode,
 	struct ocfs2_xattr_block *xb;
 	struct ocfs2_xattr_value_root *xv;
 	size_t size;
-	int ret = -ENODATA, name_offset, name_len, block_off, i;
+	int ret = -ENODATA, name_offset, name_len, i;
+	int uninitialized_var(block_off);
 
 	xs->bucket = ocfs2_xattr_bucket_new(inode);
 	if (!xs->bucket) {
-- 
GitLab


From cbfa9639aea5007313b75ec43b689d5f9e0c037d Mon Sep 17 00:00:00 2001
From: Wengang Wang <wen.gang.wang@oracle.com>
Date: Mon, 13 Jul 2009 11:38:23 +0800
Subject: [PATCH 0045/1153] ocfs2: Fix error return in ocfs2_write_cluster()

A typo caused ocfs2_write_cluster() to return 0 in some error cases.
Fix it.

Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/aops.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/ocfs2/aops.c b/fs/ocfs2/aops.c
index b2c52b3a148..25aced3b0c7 100644
--- a/fs/ocfs2/aops.c
+++ b/fs/ocfs2/aops.c
@@ -1301,7 +1301,7 @@ static int ocfs2_write_cluster(struct address_space *mapping,
 		if (tmpret) {
 			mlog_errno(tmpret);
 			if (ret == 0)
-				tmpret = ret;
+				ret = tmpret;
 		}
 	}
 
-- 
GitLab


From 1f4cea3790bf44137192f441ee84af256e3bf809 Mon Sep 17 00:00:00 2001
From: Wengang Wang <wen.gang.wang@oracle.com>
Date: Mon, 13 Jul 2009 11:38:58 +0800
Subject: [PATCH 0046/1153] ocfs2: Fail ocfs2_get_block() immediately when a
 block needs allocation

ocfs2_get_block() does no allocation.  Hole filling for writes should
have happened farther up in the call chain.  We detect this case and
print an error, but we then continue with the function.  We should be
exiting immediately.

Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/aops.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/fs/ocfs2/aops.c b/fs/ocfs2/aops.c
index 25aced3b0c7..e511df10145 100644
--- a/fs/ocfs2/aops.c
+++ b/fs/ocfs2/aops.c
@@ -193,6 +193,7 @@ static int ocfs2_get_block(struct inode *inode, sector_t iblock,
 			     (unsigned long long)OCFS2_I(inode)->ip_blkno);
 			mlog(ML_ERROR, "Size %llu, clusters %u\n", (unsigned long long)i_size_read(inode), OCFS2_I(inode)->ip_clusters);
 			dump_stack();
+			goto bail;
 		}
 
 		past_eof = ocfs2_blocks_for_bytes(inode->i_sb, i_size_read(inode));
-- 
GitLab


From 3c5e10683e684ef45614c9071847e48f633d9806 Mon Sep 17 00:00:00 2001
From: Tao Ma <tao.ma@oracle.com>
Date: Tue, 21 Jul 2009 15:42:05 +0800
Subject: [PATCH 0047/1153] ocfs2: Add extra credits and access the modified bh
 in update_edge_lengths.

In normal tree rotation left process, we will never touch the tree
branch above subtree_index and ocfs2_extend_rotate_transaction doesn't
reserve the credits for them either.

But when we want to delete the rightmost extent block, we have to update
the rightmost records for all the rightmost branch(See
ocfs2_update_edge_lengths), so we have to allocate extra credits for them.
What's more, we have to access them also.

Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/alloc.c | 44 +++++++++++++++++++++++++++++++++++++++-----
 1 file changed, 39 insertions(+), 5 deletions(-)

diff --git a/fs/ocfs2/alloc.c b/fs/ocfs2/alloc.c
index 9edcde4974a..11085af7124 100644
--- a/fs/ocfs2/alloc.c
+++ b/fs/ocfs2/alloc.c
@@ -2476,15 +2476,37 @@ out_ret_path:
 	return ret;
 }
 
-static void ocfs2_update_edge_lengths(struct inode *inode, handle_t *handle,
-				      struct ocfs2_path *path)
+static int ocfs2_update_edge_lengths(struct inode *inode, handle_t *handle,
+				     int subtree_index, struct ocfs2_path *path)
 {
-	int i, idx;
+	int i, idx, ret;
 	struct ocfs2_extent_rec *rec;
 	struct ocfs2_extent_list *el;
 	struct ocfs2_extent_block *eb;
 	u32 range;
 
+	/*
+	 * In normal tree rotation process, we will never touch the
+	 * tree branch above subtree_index and ocfs2_extend_rotate_transaction
+	 * doesn't reserve the credits for them either.
+	 *
+	 * But we do have a special case here which will update the rightmost
+	 * records for all the bh in the path.
+	 * So we have to allocate extra credits and access them.
+	 */
+	ret = ocfs2_extend_trans(handle,
+				 handle->h_buffer_credits + subtree_index);
+	if (ret) {
+		mlog_errno(ret);
+		goto out;
+	}
+
+	ret = ocfs2_journal_access_path(inode, handle, path);
+	if (ret) {
+		mlog_errno(ret);
+		goto out;
+	}
+
 	/* Path should always be rightmost. */
 	eb = (struct ocfs2_extent_block *)path_leaf_bh(path)->b_data;
 	BUG_ON(eb->h_next_leaf_blk != 0ULL);
@@ -2505,6 +2527,8 @@ static void ocfs2_update_edge_lengths(struct inode *inode, handle_t *handle,
 
 		ocfs2_journal_dirty(handle, path->p_node[i].bh);
 	}
+out:
+	return ret;
 }
 
 static void ocfs2_unlink_path(struct inode *inode, handle_t *handle,
@@ -2717,7 +2741,12 @@ static int ocfs2_rotate_subtree_left(struct inode *inode, handle_t *handle,
 	if (del_right_subtree) {
 		ocfs2_unlink_subtree(inode, handle, left_path, right_path,
 				     subtree_index, dealloc);
-		ocfs2_update_edge_lengths(inode, handle, left_path);
+		ret = ocfs2_update_edge_lengths(inode, handle, subtree_index,
+						left_path);
+		if (ret) {
+			mlog_errno(ret);
+			goto out;
+		}
 
 		eb = (struct ocfs2_extent_block *)path_leaf_bh(left_path)->b_data;
 		ocfs2_et_set_last_eb_blk(et, le64_to_cpu(eb->h_blkno));
@@ -3034,7 +3063,12 @@ static int ocfs2_remove_rightmost_path(struct inode *inode, handle_t *handle,
 
 		ocfs2_unlink_subtree(inode, handle, left_path, path,
 				     subtree_index, dealloc);
-		ocfs2_update_edge_lengths(inode, handle, left_path);
+		ret = ocfs2_update_edge_lengths(inode, handle, subtree_index,
+						left_path);
+		if (ret) {
+			mlog_errno(ret);
+			goto out;
+		}
 
 		eb = (struct ocfs2_extent_block *)path_leaf_bh(left_path)->b_data;
 		ocfs2_et_set_last_eb_blk(et, le64_to_cpu(eb->h_blkno));
-- 
GitLab


From f7b1aa69be138ad9d7d3f31fa56f4c9407f56b6a Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Mon, 20 Jul 2009 12:12:36 +0200
Subject: [PATCH 0048/1153] ocfs2: Fix deadlock on umount

In commit ea455f8ab68338ba69f5d3362b342c115bea8e13, we moved the dentry lock
put process into ocfs2_wq. This causes problems during umount because ocfs2_wq
can drop references to inodes while they are being invalidated by
invalidate_inodes() causing all sorts of nasty things (invalidate_inodes()
ending in an infinite loop, "Busy inodes after umount" messages etc.).

We fix the problem by stopping ocfs2_wq from doing any further releasing of
inode references on the superblock being unmounted, wait until it finishes
the current round of releasing and finally cleaning up all the references in
dentry_lock_list from ocfs2_put_super().

The issue was tracked down by Tao Ma <tao.ma@oracle.com>.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/dcache.c | 35 +++++++++++++++++++++++++++--------
 fs/ocfs2/dcache.h |  3 +++
 fs/ocfs2/ocfs2.h  | 22 ++++++++++++++++++----
 fs/ocfs2/super.c  | 25 ++++++++++++++++++++++---
 4 files changed, 70 insertions(+), 15 deletions(-)

diff --git a/fs/ocfs2/dcache.c b/fs/ocfs2/dcache.c
index b574431a031..2f28b7de2c8 100644
--- a/fs/ocfs2/dcache.c
+++ b/fs/ocfs2/dcache.c
@@ -310,22 +310,19 @@ out_attach:
 	return ret;
 }
 
-static DEFINE_SPINLOCK(dentry_list_lock);
+DEFINE_SPINLOCK(dentry_list_lock);
 
 /* We limit the number of dentry locks to drop in one go. We have
  * this limit so that we don't starve other users of ocfs2_wq. */
 #define DL_INODE_DROP_COUNT 64
 
 /* Drop inode references from dentry locks */
-void ocfs2_drop_dl_inodes(struct work_struct *work)
+static void __ocfs2_drop_dl_inodes(struct ocfs2_super *osb, int drop_count)
 {
-	struct ocfs2_super *osb = container_of(work, struct ocfs2_super,
-					       dentry_lock_work);
 	struct ocfs2_dentry_lock *dl;
-	int drop_count = DL_INODE_DROP_COUNT;
 
 	spin_lock(&dentry_list_lock);
-	while (osb->dentry_lock_list && drop_count--) {
+	while (osb->dentry_lock_list && (drop_count < 0 || drop_count--)) {
 		dl = osb->dentry_lock_list;
 		osb->dentry_lock_list = dl->dl_next;
 		spin_unlock(&dentry_list_lock);
@@ -333,11 +330,32 @@ void ocfs2_drop_dl_inodes(struct work_struct *work)
 		kfree(dl);
 		spin_lock(&dentry_list_lock);
 	}
-	if (osb->dentry_lock_list)
+	spin_unlock(&dentry_list_lock);
+}
+
+void ocfs2_drop_dl_inodes(struct work_struct *work)
+{
+	struct ocfs2_super *osb = container_of(work, struct ocfs2_super,
+					       dentry_lock_work);
+
+	__ocfs2_drop_dl_inodes(osb, DL_INODE_DROP_COUNT);
+	/*
+	 * Don't queue dropping if umount is in progress. We flush the
+	 * list in ocfs2_dismount_volume
+	 */
+	spin_lock(&dentry_list_lock);
+	if (osb->dentry_lock_list &&
+	    !ocfs2_test_osb_flag(osb, OCFS2_OSB_DROP_DENTRY_LOCK_IMMED))
 		queue_work(ocfs2_wq, &osb->dentry_lock_work);
 	spin_unlock(&dentry_list_lock);
 }
 
+/* Flush the whole work queue */
+void ocfs2_drop_all_dl_inodes(struct ocfs2_super *osb)
+{
+	__ocfs2_drop_dl_inodes(osb, -1);
+}
+
 /*
  * ocfs2_dentry_iput() and friends.
  *
@@ -368,7 +386,8 @@ static void ocfs2_drop_dentry_lock(struct ocfs2_super *osb,
 	/* We leave dropping of inode reference to ocfs2_wq as that can
 	 * possibly lead to inode deletion which gets tricky */
 	spin_lock(&dentry_list_lock);
-	if (!osb->dentry_lock_list)
+	if (!osb->dentry_lock_list &&
+	    !ocfs2_test_osb_flag(osb, OCFS2_OSB_DROP_DENTRY_LOCK_IMMED))
 		queue_work(ocfs2_wq, &osb->dentry_lock_work);
 	dl->dl_next = osb->dentry_lock_list;
 	osb->dentry_lock_list = dl;
diff --git a/fs/ocfs2/dcache.h b/fs/ocfs2/dcache.h
index faa12e75f98..f5dd1789acf 100644
--- a/fs/ocfs2/dcache.h
+++ b/fs/ocfs2/dcache.h
@@ -49,10 +49,13 @@ struct ocfs2_dentry_lock {
 int ocfs2_dentry_attach_lock(struct dentry *dentry, struct inode *inode,
 			     u64 parent_blkno);
 
+extern spinlock_t dentry_list_lock;
+
 void ocfs2_dentry_lock_put(struct ocfs2_super *osb,
 			   struct ocfs2_dentry_lock *dl);
 
 void ocfs2_drop_dl_inodes(struct work_struct *work);
+void ocfs2_drop_all_dl_inodes(struct ocfs2_super *osb);
 
 struct dentry *ocfs2_find_local_alias(struct inode *inode, u64 parent_blkno,
 				      int skip_unhashed);
diff --git a/fs/ocfs2/ocfs2.h b/fs/ocfs2/ocfs2.h
index c9345ebb849..39e1d5a3950 100644
--- a/fs/ocfs2/ocfs2.h
+++ b/fs/ocfs2/ocfs2.h
@@ -224,10 +224,12 @@ enum ocfs2_mount_options
 	OCFS2_MOUNT_GRPQUOTA = 1 << 10, /* We support group quotas */
 };
 
-#define OCFS2_OSB_SOFT_RO	0x0001
-#define OCFS2_OSB_HARD_RO	0x0002
-#define OCFS2_OSB_ERROR_FS	0x0004
-#define OCFS2_DEFAULT_ATIME_QUANTUM	60
+#define OCFS2_OSB_SOFT_RO			0x0001
+#define OCFS2_OSB_HARD_RO			0x0002
+#define OCFS2_OSB_ERROR_FS			0x0004
+#define OCFS2_OSB_DROP_DENTRY_LOCK_IMMED	0x0008
+
+#define OCFS2_DEFAULT_ATIME_QUANTUM		60
 
 struct ocfs2_journal;
 struct ocfs2_slot_info;
@@ -490,6 +492,18 @@ static inline void ocfs2_set_osb_flag(struct ocfs2_super *osb,
 	spin_unlock(&osb->osb_lock);
 }
 
+
+static inline unsigned long  ocfs2_test_osb_flag(struct ocfs2_super *osb,
+						 unsigned long flag)
+{
+	unsigned long ret;
+
+	spin_lock(&osb->osb_lock);
+	ret = osb->osb_flags & flag;
+	spin_unlock(&osb->osb_lock);
+	return ret;
+}
+
 static inline void ocfs2_set_ro_flag(struct ocfs2_super *osb,
 				     int hard)
 {
diff --git a/fs/ocfs2/super.c b/fs/ocfs2/super.c
index 63af2e36d83..f2893878f8a 100644
--- a/fs/ocfs2/super.c
+++ b/fs/ocfs2/super.c
@@ -1213,14 +1213,27 @@ static int ocfs2_get_sb(struct file_system_type *fs_type,
 			   mnt);
 }
 
+static void ocfs2_kill_sb(struct super_block *sb)
+{
+	struct ocfs2_super *osb = OCFS2_SB(sb);
+
+	/* Prevent further queueing of inode drop events */
+	spin_lock(&dentry_list_lock);
+	ocfs2_set_osb_flag(osb, OCFS2_OSB_DROP_DENTRY_LOCK_IMMED);
+	spin_unlock(&dentry_list_lock);
+	/* Wait for work to finish and/or remove it */
+	cancel_work_sync(&osb->dentry_lock_work);
+
+	kill_block_super(sb);
+}
+
 static struct file_system_type ocfs2_fs_type = {
 	.owner          = THIS_MODULE,
 	.name           = "ocfs2",
 	.get_sb         = ocfs2_get_sb, /* is this called when we mount
 					* the fs? */
-	.kill_sb        = kill_block_super, /* set to the generic one
-					     * right now, but do we
-					     * need to change that? */
+	.kill_sb        = ocfs2_kill_sb,
+
 	.fs_flags       = FS_REQUIRES_DEV|FS_RENAME_DOES_D_MOVE,
 	.next           = NULL
 };
@@ -1819,6 +1832,12 @@ static void ocfs2_dismount_volume(struct super_block *sb, int mnt_err)
 
 	debugfs_remove(osb->osb_ctxt);
 
+	/*
+	 * Flush inode dropping work queue so that deletes are
+	 * performed while the filesystem is still working
+	 */
+	ocfs2_drop_all_dl_inodes(osb);
+
 	/* Orphan scan should be stopped as early as possible */
 	ocfs2_orphan_scan_stop(osb);
 
-- 
GitLab


From 1bec1aed1e7e632b3cc43b6807c2b4dcd1572e28 Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Wed, 22 Jul 2009 09:59:00 -0400
Subject: [PATCH 0049/1153] Btrfs: fix definition of struct
 btrfs_extent_inline_ref

use __le64 instead of u64 in on-disk structure definition.

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/ctree.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h
index a404ecc53eb..da0763135bf 100644
--- a/fs/btrfs/ctree.h
+++ b/fs/btrfs/ctree.h
@@ -483,7 +483,7 @@ struct btrfs_shared_data_ref {
 
 struct btrfs_extent_inline_ref {
 	u8 type;
-	u64 offset;
+	__le64 offset;
 } __attribute__ ((__packed__));
 
 /* old style backrefs item */
-- 
GitLab


From bf1fb512a58d7aeb41aaa40d6d2d2d29e08e506a Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Wed, 22 Jul 2009 09:59:00 -0400
Subject: [PATCH 0050/1153] Btrfs: properly update space information after
 shrinking device.

Change 'goto done' to 'break' for the case of all device extents have
been freed, so that the code updates space information will be execute.

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/volumes.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c
index 3ab80e9cd76..f057730a72b 100644
--- a/fs/btrfs/volumes.c
+++ b/fs/btrfs/volumes.c
@@ -2007,7 +2007,7 @@ int btrfs_shrink_device(struct btrfs_device *device, u64 new_size)
 			goto done;
 		if (ret) {
 			ret = 0;
-			goto done;
+			break;
 		}
 
 		l = path->nodes[0];
@@ -2015,7 +2015,7 @@ int btrfs_shrink_device(struct btrfs_device *device, u64 new_size)
 		btrfs_item_key_to_cpu(l, &key, path->slots[0]);
 
 		if (key.objectid != device->devid)
-			goto done;
+			break;
 
 		dev_extent = btrfs_item_ptr(l, slot, struct btrfs_dev_extent);
 		length = btrfs_dev_extent_length(l, dev_extent);
-- 
GitLab


From e457afec60fdbd86b963d36f4a8a9285088c6043 Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Wed, 22 Jul 2009 09:59:00 -0400
Subject: [PATCH 0051/1153] Btrfs: fix double increment of path->slots[0] in
 btrfs_next_leaf

if 1 is returned by btrfs_search_slot, the path already points to the
first item with 'key > searching key'. So increasing path->slots[0] by
one is superfluous in that case.

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/ctree.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c
index 60a45f3a4e9..7bb66c65ddf 100644
--- a/fs/btrfs/ctree.c
+++ b/fs/btrfs/ctree.c
@@ -4146,7 +4146,8 @@ again:
 	 * advance the path if there are now more items available.
 	 */
 	if (nritems > 0 && path->slots[0] < nritems - 1) {
-		path->slots[0]++;
+		if (ret == 0)
+			path->slots[0]++;
 		ret = 0;
 		goto done;
 	}
-- 
GitLab


From 33c66f430bfa3a033e70470e4c93f967156b696d Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Wed, 22 Jul 2009 09:59:00 -0400
Subject: [PATCH 0052/1153] Btrfs: fix locking issue in btrfs_find_next_key

When walking up the tree, btrfs_find_next_key assumes the upper level tree
block is properly locked. This isn't always true even path->keep_locks is 1.
This is because btrfs_find_next_key may advance path->slots[] several times
instead of only once.

When 'path->slots[level] >= btrfs_header_nritems(path->nodes[level])' is found,
we can't guarantee the original value of 'path->slots[level]' is
'btrfs_header_nritems(path->nodes[level]) - 1'. If it's not, the tree block at
'level + 1' isn't locked.

This patch fixes the issue by explicitly checking the locking state,
re-searching the tree if it's not locked.

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/ctree.c      | 95 ++++++++++++++++++++++++++++---------------
 fs/btrfs/relocation.c |  3 ++
 2 files changed, 65 insertions(+), 33 deletions(-)

diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c
index 7bb66c65ddf..fdd423a550d 100644
--- a/fs/btrfs/ctree.c
+++ b/fs/btrfs/ctree.c
@@ -1701,6 +1701,7 @@ int btrfs_search_slot(struct btrfs_trans_handle *trans, struct btrfs_root
 	struct extent_buffer *b;
 	int slot;
 	int ret;
+	int err;
 	int level;
 	int lowest_unlock = 1;
 	u8 lowest_level = 0;
@@ -1737,8 +1738,6 @@ again:
 			p->locks[level] = 1;
 
 		if (cow) {
-			int wret;
-
 			/*
 			 * if we don't really need to cow this block
 			 * then we don't want to set the path blocking,
@@ -1749,12 +1748,12 @@ again:
 
 			btrfs_set_path_blocking(p);
 
-			wret = btrfs_cow_block(trans, root, b,
-					       p->nodes[level + 1],
-					       p->slots[level + 1], &b);
-			if (wret) {
+			err = btrfs_cow_block(trans, root, b,
+					      p->nodes[level + 1],
+					      p->slots[level + 1], &b);
+			if (err) {
 				free_extent_buffer(b);
-				ret = wret;
+				ret = err;
 				goto done;
 			}
 		}
@@ -1793,41 +1792,45 @@ cow_done:
 		ret = bin_search(b, key, level, &slot);
 
 		if (level != 0) {
-			if (ret && slot > 0)
+			int dec = 0;
+			if (ret && slot > 0) {
+				dec = 1;
 				slot -= 1;
+			}
 			p->slots[level] = slot;
-			ret = setup_nodes_for_search(trans, root, p, b, level,
+			err = setup_nodes_for_search(trans, root, p, b, level,
 						     ins_len);
-			if (ret == -EAGAIN)
+			if (err == -EAGAIN)
 				goto again;
-			else if (ret)
+			if (err) {
+				ret = err;
 				goto done;
+			}
 			b = p->nodes[level];
 			slot = p->slots[level];
 
 			unlock_up(p, level, lowest_unlock);
 
-			/* this is only true while dropping a snapshot */
 			if (level == lowest_level) {
-				ret = 0;
+				if (dec)
+					p->slots[level]++;
 				goto done;
 			}
 
-			ret = read_block_for_search(trans, root, p,
+			err = read_block_for_search(trans, root, p,
 						    &b, level, slot, key);
-			if (ret == -EAGAIN)
+			if (err == -EAGAIN)
 				goto again;
-
-			if (ret == -EIO)
+			if (err) {
+				ret = err;
 				goto done;
+			}
 
 			if (!p->skip_locking) {
-				int lret;
-
 				btrfs_clear_path_blocking(p, NULL);
-				lret = btrfs_try_spin_lock(b);
+				err = btrfs_try_spin_lock(b);
 
-				if (!lret) {
+				if (!err) {
 					btrfs_set_path_blocking(p);
 					btrfs_tree_lock(b);
 					btrfs_clear_path_blocking(p, b);
@@ -1837,16 +1840,14 @@ cow_done:
 			p->slots[level] = slot;
 			if (ins_len > 0 &&
 			    btrfs_leaf_free_space(root, b) < ins_len) {
-				int sret;
-
 				btrfs_set_path_blocking(p);
-				sret = split_leaf(trans, root, key,
-						      p, ins_len, ret == 0);
+				err = split_leaf(trans, root, key,
+						 p, ins_len, ret == 0);
 				btrfs_clear_path_blocking(p, NULL);
 
-				BUG_ON(sret > 0);
-				if (sret) {
-					ret = sret;
+				BUG_ON(err > 0);
+				if (err) {
+					ret = err;
 					goto done;
 				}
 			}
@@ -4042,10 +4043,9 @@ out:
  * calling this function.
  */
 int btrfs_find_next_key(struct btrfs_root *root, struct btrfs_path *path,
-			struct btrfs_key *key, int lowest_level,
+			struct btrfs_key *key, int level,
 			int cache_only, u64 min_trans)
 {
-	int level = lowest_level;
 	int slot;
 	struct extent_buffer *c;
 
@@ -4058,11 +4058,40 @@ int btrfs_find_next_key(struct btrfs_root *root, struct btrfs_path *path,
 		c = path->nodes[level];
 next:
 		if (slot >= btrfs_header_nritems(c)) {
-			level++;
-			if (level == BTRFS_MAX_LEVEL)
+			int ret;
+			int orig_lowest;
+			struct btrfs_key cur_key;
+			if (level + 1 >= BTRFS_MAX_LEVEL ||
+			    !path->nodes[level + 1])
 				return 1;
-			continue;
+
+			if (path->locks[level + 1]) {
+				level++;
+				continue;
+			}
+
+			slot = btrfs_header_nritems(c) - 1;
+			if (level == 0)
+				btrfs_item_key_to_cpu(c, &cur_key, slot);
+			else
+				btrfs_node_key_to_cpu(c, &cur_key, slot);
+
+			orig_lowest = path->lowest_level;
+			btrfs_release_path(root, path);
+			path->lowest_level = level;
+			ret = btrfs_search_slot(NULL, root, &cur_key, path,
+						0, 0);
+			path->lowest_level = orig_lowest;
+			if (ret < 0)
+				return ret;
+
+			c = path->nodes[level];
+			slot = path->slots[level];
+			if (ret == 0)
+				slot++;
+			goto next;
 		}
+
 		if (level == 0)
 			btrfs_item_key_to_cpu(c, key, slot);
 		else {
diff --git a/fs/btrfs/relocation.c b/fs/btrfs/relocation.c
index 00839793477..e71264d1c2c 100644
--- a/fs/btrfs/relocation.c
+++ b/fs/btrfs/relocation.c
@@ -670,6 +670,8 @@ again:
 			err = ret;
 			goto out;
 		}
+		if (ret > 0 && path2->slots[level] > 0)
+			path2->slots[level]--;
 
 		eb = path2->nodes[level];
 		WARN_ON(btrfs_node_blockptr(eb, path2->slots[level]) !=
@@ -1609,6 +1611,7 @@ static noinline_for_stack int merge_reloc_root(struct reloc_control *rc,
 		BUG_ON(level == 0);
 		path->lowest_level = level;
 		ret = btrfs_search_slot(NULL, reloc_root, &key, path, 0, 0);
+		path->lowest_level = 0;
 		if (ret < 0) {
 			btrfs_free_path(path);
 			return ret;
-- 
GitLab


From 4a8c9a62d7f7f058eed4b8a6f2c890a887778093 Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Wed, 22 Jul 2009 10:07:05 -0400
Subject: [PATCH 0053/1153] Btrfs: make sure all dirty blocks are written at
 commit time

Write dirty block groups may allocate new block, and so may add new delayed
back ref. btrfs_run_delayed_refs may make some block groups dirty.

commit_cowonly_roots does not handle the recursion properly, and some dirty
blocks can be left unwritten at commit time. This patch moves
btrfs_run_delayed_refs into the loop that writes dirty block groups, and makes
the code not break out of the loop until there are no dirty block groups or
delayed back refs.

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/extent-tree.c | 70 +++++++++++++++++++++++++-----------------
 fs/btrfs/transaction.c |  9 +-----
 2 files changed, 42 insertions(+), 37 deletions(-)

diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index a5aca3997d4..62a332d34fd 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -2387,13 +2387,29 @@ fail:
 
 }
 
+static struct btrfs_block_group_cache *
+next_block_group(struct btrfs_root *root,
+		 struct btrfs_block_group_cache *cache)
+{
+	struct rb_node *node;
+	spin_lock(&root->fs_info->block_group_cache_lock);
+	node = rb_next(&cache->cache_node);
+	btrfs_put_block_group(cache);
+	if (node) {
+		cache = rb_entry(node, struct btrfs_block_group_cache,
+				 cache_node);
+		atomic_inc(&cache->count);
+	} else
+		cache = NULL;
+	spin_unlock(&root->fs_info->block_group_cache_lock);
+	return cache;
+}
+
 int btrfs_write_dirty_block_groups(struct btrfs_trans_handle *trans,
 				   struct btrfs_root *root)
 {
-	struct btrfs_block_group_cache *cache, *entry;
-	struct rb_node *n;
+	struct btrfs_block_group_cache *cache;
 	int err = 0;
-	int werr = 0;
 	struct btrfs_path *path;
 	u64 last = 0;
 
@@ -2402,39 +2418,35 @@ int btrfs_write_dirty_block_groups(struct btrfs_trans_handle *trans,
 		return -ENOMEM;
 
 	while (1) {
-		cache = NULL;
-		spin_lock(&root->fs_info->block_group_cache_lock);
-		for (n = rb_first(&root->fs_info->block_group_cache_tree);
-		     n; n = rb_next(n)) {
-			entry = rb_entry(n, struct btrfs_block_group_cache,
-					 cache_node);
-			if (entry->dirty) {
-				cache = entry;
-				break;
-			}
+		if (last == 0) {
+			err = btrfs_run_delayed_refs(trans, root,
+						     (unsigned long)-1);
+			BUG_ON(err);
 		}
-		spin_unlock(&root->fs_info->block_group_cache_lock);
 
-		if (!cache)
-			break;
+		cache = btrfs_lookup_first_block_group(root->fs_info, last);
+		while (cache) {
+			if (cache->dirty)
+				break;
+			cache = next_block_group(root, cache);
+		}
+		if (!cache) {
+			if (last == 0)
+				break;
+			last = 0;
+			continue;
+		}
 
 		cache->dirty = 0;
-		last += cache->key.offset;
+		last = cache->key.objectid + cache->key.offset;
 
-		err = write_one_cache_group(trans, root,
-					    path, cache);
-		/*
-		 * if we fail to write the cache group, we want
-		 * to keep it marked dirty in hopes that a later
-		 * write will work
-		 */
-		if (err) {
-			werr = err;
-			continue;
-		}
+		err = write_one_cache_group(trans, root, path, cache);
+		BUG_ON(err);
+		btrfs_put_block_group(cache);
 	}
+
 	btrfs_free_path(path);
-	return werr;
+	return 0;
 }
 
 int btrfs_extent_readonly(struct btrfs_root *root, u64 bytenr)
diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c
index 2dbf1c1f56e..81f7124c305 100644
--- a/fs/btrfs/transaction.c
+++ b/fs/btrfs/transaction.c
@@ -444,9 +444,6 @@ static int update_cowonly_root(struct btrfs_trans_handle *trans,
 
 	btrfs_write_dirty_block_groups(trans, root);
 
-	ret = btrfs_run_delayed_refs(trans, root, (unsigned long)-1);
-	BUG_ON(ret);
-
 	while (1) {
 		old_root_bytenr = btrfs_root_bytenr(&root->root_item);
 		if (old_root_bytenr == root->node->start)
@@ -457,9 +454,8 @@ static int update_cowonly_root(struct btrfs_trans_handle *trans,
 					&root->root_key,
 					&root->root_item);
 		BUG_ON(ret);
-		btrfs_write_dirty_block_groups(trans, root);
 
-		ret = btrfs_run_delayed_refs(trans, root, (unsigned long)-1);
+		ret = btrfs_write_dirty_block_groups(trans, root);
 		BUG_ON(ret);
 	}
 	free_extent_buffer(root->commit_root);
@@ -495,9 +491,6 @@ static noinline int commit_cowonly_roots(struct btrfs_trans_handle *trans,
 		root = list_entry(next, struct btrfs_root, dirty_list);
 
 		update_cowonly_root(trans, root);
-
-		ret = btrfs_run_delayed_refs(trans, root, (unsigned long)-1);
-		BUG_ON(ret);
 	}
 	return 0;
 }
-- 
GitLab


From 29c5e8ce01f9dad7e24b99c21e4f836d6b0289e0 Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Wed, 22 Jul 2009 16:49:00 -0400
Subject: [PATCH 0054/1153] Btrfs: convert nested spin_lock_irqsave to
 spin_lock

If spin_lock_irqsave is called twice in a row with the same second
argument, the interrupt state at the point of the second call overwrites
the value saved by the first call.  Indeed, the second call does not need
to save the interrupt state, so it is changed to a simple spin_lock.

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/async-thread.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/fs/btrfs/async-thread.c b/fs/btrfs/async-thread.c
index 6e4f6c50a12..019e8af449a 100644
--- a/fs/btrfs/async-thread.c
+++ b/fs/btrfs/async-thread.c
@@ -424,11 +424,11 @@ int btrfs_requeue_work(struct btrfs_work *work)
 	 * list
 	 */
 	if (worker->idle) {
-		spin_lock_irqsave(&worker->workers->lock, flags);
+		spin_lock(&worker->workers->lock);
 		worker->idle = 0;
 		list_move_tail(&worker->worker_list,
 			       &worker->workers->worker_list);
-		spin_unlock_irqrestore(&worker->workers->lock, flags);
+		spin_unlock(&worker->workers->lock);
 	}
 	if (!worker->working) {
 		wake = 1;
-- 
GitLab


From 3acada49c2794c5aac21849e2ea05790c6dd2faa Mon Sep 17 00:00:00 2001
From: David Woodhouse <dwmw2@infradead.org>
Date: Wed, 22 Jul 2009 16:49:01 -0400
Subject: [PATCH 0055/1153] Btrfs: Remove broken sanity check from
 btrfs_rmap_block()

It was never actually doing anything anyway (see the loop condition),
and it would be difficult to make it work for RAID[56].

Even if it was actually working, it's checking for the wrong thing
anyway. Instead of checking whether we list a block which _doesn't_ land
at the relevant physical location, it should be checking that we _have_
listed all the logical blocks which refer to the required physical
location on all devices.

This function is only called from remove_sb_from_cache() to ensure that
we reserve the logical blocks which would reside at the same physical
location as the superblock copies. So listing more blocks than we need
is actually OK.

With RAID[56] we're going to throw away an entire stripe for each block
we have to ignore, so we _are_ going to list blocks other than the
ones which actually contain the superblock.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/volumes.c | 20 --------------------
 1 file changed, 20 deletions(-)

diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c
index f057730a72b..55c37276a29 100644
--- a/fs/btrfs/volumes.c
+++ b/fs/btrfs/volumes.c
@@ -2795,26 +2795,6 @@ int btrfs_rmap_block(struct btrfs_mapping_tree *map_tree,
 		}
 	}
 
-	for (i = 0; i > nr; i++) {
-		struct btrfs_multi_bio *multi;
-		struct btrfs_bio_stripe *stripe;
-		int ret;
-
-		length = 1;
-		ret = btrfs_map_block(map_tree, WRITE, buf[i],
-				      &length, &multi, 0);
-		BUG_ON(ret);
-
-		stripe = multi->stripes;
-		for (j = 0; j < multi->num_stripes; j++) {
-			if (stripe->physical >= physical &&
-			    physical < stripe->physical + length)
-				break;
-		}
-		BUG_ON(j >= multi->num_stripes);
-		kfree(multi);
-	}
-
 	*logical = buf;
 	*naddrs = nr;
 	*stripe_len = map->stripe_len;
-- 
GitLab


From 33c17ad5717c887568c1de61f15e5d58ed66d189 Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Wed, 22 Jul 2009 16:49:01 -0400
Subject: [PATCH 0056/1153] Btrfs: adjust NULL test

Move the call to BUG_ON to before the dereference of the tested value.

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/inode.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c
index a48c084f6d3..3ea827ddf0f 100644
--- a/fs/btrfs/inode.c
+++ b/fs/btrfs/inode.c
@@ -2607,8 +2607,8 @@ noinline int btrfs_truncate_inode_items(struct btrfs_trans_handle *trans,
 	if (root->ref_cows)
 		btrfs_drop_extent_cache(inode, new_size & (~mask), (u64)-1, 0);
 	path = btrfs_alloc_path();
-	path->reada = -1;
 	BUG_ON(!path);
+	path->reada = -1;
 
 	/* FIXME, add redo link to tree so we don't leak on crash */
 	key.objectid = inode->i_ino;
-- 
GitLab


From c271b492419a18908ba19ee02b231fb305a27023 Mon Sep 17 00:00:00 2001
From: Daniel Cadete <danielcadete10@gmail.com>
Date: Wed, 22 Jul 2009 16:52:13 -0400
Subject: [PATCH 0057/1153] Btrfs: remove of redundant btrfs_header_level

This removes the continues call's of btrfs_header_level. One call of
btrfs_header_level(c) its enough.

Signed-off-by Daniel Cadete <danielncadete10@gmail.com>

Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/print-tree.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/fs/btrfs/print-tree.c b/fs/btrfs/print-tree.c
index 6d6523da0a3..0d126be22b6 100644
--- a/fs/btrfs/print-tree.c
+++ b/fs/btrfs/print-tree.c
@@ -309,7 +309,7 @@ void btrfs_print_tree(struct btrfs_root *root, struct extent_buffer *c)
 	}
 	printk(KERN_INFO "node %llu level %d total ptrs %d free spc %u\n",
 	       (unsigned long long)btrfs_header_bytenr(c),
-	       btrfs_header_level(c), nr,
+	      level, nr,
 	       (u32)BTRFS_NODEPTRS_PER_BLOCK(root) - nr);
 	for (i = 0; i < nr; i++) {
 		btrfs_node_key_to_cpu(c, &key, i);
@@ -326,10 +326,10 @@ void btrfs_print_tree(struct btrfs_root *root, struct extent_buffer *c)
 					btrfs_level_size(root, level - 1),
 					btrfs_node_ptr_generation(c, i));
 		if (btrfs_is_leaf(next) &&
-		    btrfs_header_level(c) != 1)
+		   level != 1)
 			BUG();
 		if (btrfs_header_level(next) !=
-			btrfs_header_level(c) - 1)
+		       level - 1)
 			BUG();
 		btrfs_print_tree(root, next);
 		free_extent_buffer(next);
-- 
GitLab


From 83121942b28daffc9526b14b7843d8cdbd3db641 Mon Sep 17 00:00:00 2001
From: David Woodhouse <dwmw2@infradead.org>
Date: Wed, 22 Jul 2009 16:52:13 -0400
Subject: [PATCH 0058/1153] Btrfs: Fix crash on read failures at mount

If the tree roots hit read errors during mount, btrfs is not properly
erroring out.  We need to check the uptodate bits after
reading in the tree root node.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/disk-io.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c
index 0d50d49d990..55d9d188e69 100644
--- a/fs/btrfs/disk-io.c
+++ b/fs/btrfs/disk-io.c
@@ -1783,6 +1783,11 @@ struct btrfs_root *open_ctree(struct super_block *sb,
 					   btrfs_super_chunk_root(disk_super),
 					   blocksize, generation);
 	BUG_ON(!chunk_root->node);
+	if (!test_bit(EXTENT_BUFFER_UPTODATE, &chunk_root->node->bflags)) {
+		printk(KERN_WARNING "btrfs: failed to read chunk root on %s\n",
+		       sb->s_id);
+		goto fail_chunk_root;
+	}
 	btrfs_set_root_node(&chunk_root->root_item, chunk_root->node);
 	chunk_root->commit_root = btrfs_root_node(chunk_root);
 
@@ -1810,6 +1815,11 @@ struct btrfs_root *open_ctree(struct super_block *sb,
 					  blocksize, generation);
 	if (!tree_root->node)
 		goto fail_chunk_root;
+	if (!test_bit(EXTENT_BUFFER_UPTODATE, &tree_root->node->bflags)) {
+		printk(KERN_WARNING "btrfs: failed to read tree root on %s\n",
+		       sb->s_id);
+		goto fail_tree_root;
+	}
 	btrfs_set_root_node(&tree_root->root_item, tree_root->node);
 	tree_root->commit_root = btrfs_root_node(tree_root);
 
-- 
GitLab


From 2ded9e2747d0a390d281bb5b16ff7f640ec85f78 Mon Sep 17 00:00:00 2001
From: "ling.ma@intel.com" <ling.ma@intel.com>
Date: Thu, 16 Jul 2009 17:23:09 +0800
Subject: [PATCH 0059/1153] drm/i915: hdmi detection according by reading edid

According to investigations from windows team ,hw team,
and our test results on all 4x platofrms available
(gm45, g45b, q45, g45a, g45c, g41a, and g41), we find
currently Hot plug live status and Hot plug interrupt
detection are not reliable, sometime the results from
the two approaches are contradicts. So we chose edid
detection for hdmi output.

Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_hdmi.c | 64 ++-----------------------------
 1 file changed, 4 insertions(+), 60 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 9e30daae37d..1842290cded 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -130,16 +130,17 @@ static bool intel_hdmi_mode_fixup(struct drm_encoder *encoder,
 }
 
 static enum drm_connector_status
-intel_hdmi_edid_detect(struct drm_connector *connector)
+intel_hdmi_detect(struct drm_connector *connector)
 {
 	struct intel_output *intel_output = to_intel_output(connector);
 	struct intel_hdmi_priv *hdmi_priv = intel_output->dev_priv;
 	struct edid *edid = NULL;
 	enum drm_connector_status status = connector_status_disconnected;
 
+	hdmi_priv->has_hdmi_sink = false;
 	edid = drm_get_edid(&intel_output->base,
 			    intel_output->ddc_bus);
-	hdmi_priv->has_hdmi_sink = false;
+
 	if (edid) {
 		if (edid->input & DRM_EDID_INPUT_DIGITAL) {
 			status = connector_status_connected;
@@ -148,65 +149,8 @@ intel_hdmi_edid_detect(struct drm_connector *connector)
 		intel_output->base.display_info.raw_edid = NULL;
 		kfree(edid);
 	}
-	return status;
-}
-
-static enum drm_connector_status
-igdng_hdmi_detect(struct drm_connector *connector)
-{
-	struct intel_output *intel_output = to_intel_output(connector);
-	struct intel_hdmi_priv *hdmi_priv = intel_output->dev_priv;
-
-	/* FIXME hotplug detect */
-
-	hdmi_priv->has_hdmi_sink = false;
-	return intel_hdmi_edid_detect(connector);
-}
 
-static enum drm_connector_status
-intel_hdmi_detect(struct drm_connector *connector)
-{
-	struct drm_device *dev = connector->dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_output *intel_output = to_intel_output(connector);
-	struct intel_hdmi_priv *hdmi_priv = intel_output->dev_priv;
-	u32 temp, bit;
-
-	if (IS_IGDNG(dev))
-		return igdng_hdmi_detect(connector);
-
-	temp = I915_READ(PORT_HOTPLUG_EN);
-
-	switch (hdmi_priv->sdvox_reg) {
-	case SDVOB:
-		temp |= HDMIB_HOTPLUG_INT_EN;
-		break;
-	case SDVOC:
-		temp |= HDMIC_HOTPLUG_INT_EN;
-		break;
-	default:
-		return connector_status_unknown;
-	}
-
-	I915_WRITE(PORT_HOTPLUG_EN, temp);
-
-	POSTING_READ(PORT_HOTPLUG_EN);
-
-	switch (hdmi_priv->sdvox_reg) {
-	case SDVOB:
-		bit = HDMIB_HOTPLUG_INT_STATUS;
-		break;
-	case SDVOC:
-		bit = HDMIC_HOTPLUG_INT_STATUS;
-		break;
-	default:
-		return connector_status_unknown;
-	}
-
-	if ((I915_READ(PORT_HOTPLUG_STAT) & bit) != 0)
-		return intel_hdmi_edid_detect(connector);
-	else
-		return connector_status_disconnected;
+	return status;
 }
 
 static int intel_hdmi_get_modes(struct drm_connector *connector)
-- 
GitLab


From 1d3e216f1d303878d7204de94dee251bc2702175 Mon Sep 17 00:00:00 2001
From: Mike Rapoport <mike@compulab.co.il>
Date: Tue, 21 Jul 2009 17:09:52 +0300
Subject: [PATCH 0060/1153] [ARM] pxa/em-x270: fix compile failure when
 CONFIG_APM_EMULATION=n

If CONFIG_APM_EMULATION=n em-x270 build fails with linker error:

arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_critical': em-x270.c:(.text+0x12c0): undefined reference to `apm_queue_event'
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_low': em-x270.c:(.text+0x12c8): undefined reference to `apm_queue_event'
make: *** [.tmp_vmlinux1] Error 1

Fix it.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
---
 arch/arm/mach-pxa/em-x270.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c
index 63b10d9bb1d..9cd09465a0e 100644
--- a/arch/arm/mach-pxa/em-x270.c
+++ b/arch/arm/mach-pxa/em-x270.c
@@ -1141,12 +1141,16 @@ struct power_supply_info em_x270_psy_info = {
 
 static void em_x270_battery_low(void)
 {
+#if defined(CONFIG_APM_EMULATION)
 	apm_queue_event(APM_LOW_BATTERY);
+#endif
 }
 
 static void em_x270_battery_critical(void)
 {
+#if defined(CONFIG_APM_EMULATION)
 	apm_queue_event(APM_CRITICAL_SUSPEND);
+#endif
 }
 
 struct da9030_battery_info em_x270_batterty_info = {
-- 
GitLab


From e3d433040ee6077e33d4ad22e2f60a38b085786d Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Sun, 28 Jun 2009 09:26:20 -0700
Subject: [PATCH 0061/1153] drivers/dma/fsldma.c: Remove unnecessary semicolons

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 drivers/dma/fsldma.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c
index 6e60c77a145..ef87a898414 100644
--- a/drivers/dma/fsldma.c
+++ b/drivers/dma/fsldma.c
@@ -142,7 +142,7 @@ static int dma_is_idle(struct fsl_dma_chan *fsl_chan)
 
 static void dma_start(struct fsl_dma_chan *fsl_chan)
 {
-	u32 mr_set = 0;;
+	u32 mr_set = 0;
 
 	if (fsl_chan->feature & FSL_DMA_CHAN_PAUSE_EXT) {
 		DMA_OUT(fsl_chan, &fsl_chan->reg_base->bcr, 0, 32);
-- 
GitLab


From c019894efc9c9ba5939948caa78c133b1ec8ae63 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Sun, 28 Jun 2009 09:26:21 -0700
Subject: [PATCH 0062/1153] drivers/dma: Remove unnecessary semicolons

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 drivers/dma/dmatest.c | 2 +-
 drivers/dma/mv_xor.c  | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c
index fb7da5141e9..cec1ec0b7d0 100644
--- a/drivers/dma/dmatest.c
+++ b/drivers/dma/dmatest.c
@@ -114,7 +114,7 @@ static void dmatest_init_srcs(u8 **bufs, unsigned int start, unsigned int len)
 			buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK);
 		for ( ; i < start + len; i++)
 			buf[i] = PATTERN_SRC | PATTERN_COPY
-				| (~i & PATTERN_COUNT_MASK);;
+				| (~i & PATTERN_COUNT_MASK);
 		for ( ; i < test_buf_size; i++)
 			buf[i] = PATTERN_SRC | (~i & PATTERN_COUNT_MASK);
 		buf++;
diff --git a/drivers/dma/mv_xor.c b/drivers/dma/mv_xor.c
index ddab94f5122..3f23eabe09f 100644
--- a/drivers/dma/mv_xor.c
+++ b/drivers/dma/mv_xor.c
@@ -1176,7 +1176,7 @@ static int __devinit mv_xor_probe(struct platform_device *pdev)
 	if (dma_has_cap(DMA_MEMSET, dma_dev->cap_mask))
 		dma_dev->device_prep_dma_memset = mv_xor_prep_dma_memset;
 	if (dma_has_cap(DMA_XOR, dma_dev->cap_mask)) {
-		dma_dev->max_xor = 8;                  ;
+		dma_dev->max_xor = 8;
 		dma_dev->device_prep_dma_xor = mv_xor_prep_dma_xor;
 	}
 
-- 
GitLab


From 0a2ff57d6fba92842272889b4bca447344cd9d36 Mon Sep 17 00:00:00 2001
From: Nicolas Ferre <nicolas.ferre@atmel.com>
Date: Fri, 3 Jul 2009 19:26:51 +0200
Subject: [PATCH 0063/1153] dmaengine: dmatest: add a maximum number of test
 iterations

The dmatest usually waits for the killing of its kthreads to stop
running tests.  This patch adds a parameter that sets a maximum
number of test iterations.

This feature is quite interesting for debugging when you set a lot of
traces in your dmaengine controller driver.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 drivers/dma/dmatest.c | 15 ++++++++++++++-
 1 file changed, 14 insertions(+), 1 deletion(-)

diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c
index cec1ec0b7d0..2d973d60e7b 100644
--- a/drivers/dma/dmatest.c
+++ b/drivers/dma/dmatest.c
@@ -38,6 +38,11 @@ module_param(max_channels, uint, S_IRUGO);
 MODULE_PARM_DESC(max_channels,
 		"Maximum number of channels to use (default: all)");
 
+static unsigned int iterations;
+module_param(iterations, uint, S_IRUGO);
+MODULE_PARM_DESC(iterations,
+		"Iterations before stopping test (default: infinite)");
+
 static unsigned int xor_sources = 3;
 module_param(xor_sources, uint, S_IRUGO);
 MODULE_PARM_DESC(xor_sources,
@@ -270,7 +275,8 @@ static int dmatest_func(void *data)
 
 	flags = DMA_CTRL_ACK | DMA_COMPL_SKIP_DEST_UNMAP | DMA_PREP_INTERRUPT;
 
-	while (!kthread_should_stop()) {
+	while (!kthread_should_stop()
+	       && !(iterations && total_tests >= iterations)) {
 		struct dma_device *dev = chan->device;
 		struct dma_async_tx_descriptor *tx = NULL;
 		dma_addr_t dma_srcs[src_cnt];
@@ -416,6 +422,13 @@ err_srcbuf:
 err_srcs:
 	pr_notice("%s: terminating after %u tests, %u failures (status %d)\n",
 			thread_name, total_tests, failed_tests, ret);
+
+	if (iterations > 0)
+		while (!kthread_should_stop()) {
+			DECLARE_WAIT_QUEUE_HEAD(wait_dmatest_exit);
+			interruptible_sleep_on(&wait_dmatest_exit);
+		}
+
 	return ret;
 }
 
-- 
GitLab


From f1aef8b6e6abf32a3a269542f95a19e2cb319f6c Mon Sep 17 00:00:00 2001
From: Nicolas Ferre <nicolas.ferre@atmel.com>
Date: Mon, 6 Jul 2009 18:19:44 +0200
Subject: [PATCH 0064/1153] dmaengine: dmatest: correct thread_count while
 using multiple thread per channel

It seems that thread_count is not properly calculated in dmatest.
In fact the thread count number that is returned from dmatest_add_threads() is
not correctly added to the thread_count and thus not properly printed.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 drivers/dma/dmatest.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c
index 2d973d60e7b..d93017fc787 100644
--- a/drivers/dma/dmatest.c
+++ b/drivers/dma/dmatest.c
@@ -508,11 +508,11 @@ static int dmatest_add_channel(struct dma_chan *chan)
 
 	if (dma_has_cap(DMA_MEMCPY, dma_dev->cap_mask)) {
 		cnt = dmatest_add_threads(dtc, DMA_MEMCPY);
-		thread_count += cnt > 0 ?: 0;
+		thread_count += cnt > 0 ? cnt : 0;
 	}
 	if (dma_has_cap(DMA_XOR, dma_dev->cap_mask)) {
 		cnt = dmatest_add_threads(dtc, DMA_XOR);
-		thread_count += cnt > 0 ?: 0;
+		thread_count += cnt > 0 ? cnt : 0;
 	}
 
 	pr_info("dmatest: Started %u threads using %s\n",
-- 
GitLab


From dc78baa2b90b289590911b40b6800f77d0dc935a Mon Sep 17 00:00:00 2001
From: Nicolas Ferre <nicolas.ferre@atmel.com>
Date: Fri, 3 Jul 2009 19:24:33 +0200
Subject: [PATCH 0065/1153] dmaengine: at_hdmac: new driver for the Atmel AHB
 DMA Controller

This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.

This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip.  On other products, it will be used
also for peripheral DMA transfer (slave API support to come).

I used dmatest client without problem in different configurations to test it.

Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 arch/arm/mach-at91/include/mach/at_hdmac.h |   26 +
 drivers/dma/Kconfig                        |    8 +
 drivers/dma/Makefile                       |    1 +
 drivers/dma/at_hdmac.c                     | 1009 ++++++++++++++++++++
 drivers/dma/at_hdmac_regs.h                |  386 ++++++++
 5 files changed, 1430 insertions(+)
 create mode 100644 arch/arm/mach-at91/include/mach/at_hdmac.h
 create mode 100644 drivers/dma/at_hdmac.c
 create mode 100644 drivers/dma/at_hdmac_regs.h

diff --git a/arch/arm/mach-at91/include/mach/at_hdmac.h b/arch/arm/mach-at91/include/mach/at_hdmac.h
new file mode 100644
index 00000000000..21a5554f9cb
--- /dev/null
+++ b/arch/arm/mach-at91/include/mach/at_hdmac.h
@@ -0,0 +1,26 @@
+/*
+ * Header file for the Atmel AHB DMA Controller driver
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef AT_HDMAC_H
+#define AT_HDMAC_H
+
+#include <linux/dmaengine.h>
+
+/**
+ * struct at_dma_platform_data - Controller configuration parameters
+ * @nr_channels: Number of channels supported by hardware (max 8)
+ * @cap_mask: dma_capability flags supported by the platform
+ */
+struct at_dma_platform_data {
+	unsigned int	nr_channels;
+	dma_cap_mask_t  cap_mask;
+};
+
+#endif /* AT_HDMAC_H */
diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index babf214a509..bc8fb41cd62 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -46,6 +46,14 @@ config DW_DMAC
 	  Support the Synopsys DesignWare AHB DMA controller.  This
 	  can be integrated in chips such as the Atmel AT32ap7000.
 
+config AT_HDMAC
+	tristate "Atmel AHB DMA support"
+	depends on ARCH_AT91SAM9RL
+	select DMA_ENGINE
+	help
+	  Support the Atmel AHB DMA controller.  This can be integrated in
+	  chips such as the Atmel AT91SAM9RL.
+
 config FSL_DMA
 	tristate "Freescale Elo and Elo Plus DMA support"
 	depends on FSL_SOC
diff --git a/drivers/dma/Makefile b/drivers/dma/Makefile
index 2e5dc96700d..d7bc5fd17d8 100644
--- a/drivers/dma/Makefile
+++ b/drivers/dma/Makefile
@@ -7,4 +7,5 @@ obj-$(CONFIG_INTEL_IOP_ADMA) += iop-adma.o
 obj-$(CONFIG_FSL_DMA) += fsldma.o
 obj-$(CONFIG_MV_XOR) += mv_xor.o
 obj-$(CONFIG_DW_DMAC) += dw_dmac.o
+obj-$(CONFIG_AT_HDMAC) += at_hdmac.o
 obj-$(CONFIG_MX3_IPU) += ipu/
diff --git a/drivers/dma/at_hdmac.c b/drivers/dma/at_hdmac.c
new file mode 100644
index 00000000000..64dbf0ce128
--- /dev/null
+++ b/drivers/dma/at_hdmac.c
@@ -0,0 +1,1009 @@
+/*
+ * Driver for the Atmel AHB DMA Controller (aka HDMA or DMAC on AT91 systems)
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ *
+ * This supports the Atmel AHB DMA Controller,
+ *
+ * The driver has currently been tested with the Atmel AT91SAM9RL
+ * and AT91SAM9G45 series.
+ */
+
+#include <linux/clk.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include "at_hdmac_regs.h"
+
+/*
+ * Glossary
+ * --------
+ *
+ * at_hdmac		: Name of the ATmel AHB DMA Controller
+ * at_dma_ / atdma	: ATmel DMA controller entity related
+ * atc_	/ atchan	: ATmel DMA Channel entity related
+ */
+
+#define	ATC_DEFAULT_CFG		(ATC_FIFOCFG_HALFFIFO)
+#define	ATC_DEFAULT_CTRLA	(0)
+#define	ATC_DEFAULT_CTRLB	(ATC_SIF(0)	\
+				|ATC_DIF(1))
+
+/*
+ * Initial number of descriptors to allocate for each channel. This could
+ * be increased during dma usage.
+ */
+static unsigned int init_nr_desc_per_channel = 64;
+module_param(init_nr_desc_per_channel, uint, 0644);
+MODULE_PARM_DESC(init_nr_desc_per_channel,
+		 "initial descriptors per channel (default: 64)");
+
+
+/* prototypes */
+static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx);
+
+
+/*----------------------------------------------------------------------*/
+
+static struct at_desc *atc_first_active(struct at_dma_chan *atchan)
+{
+	return list_first_entry(&atchan->active_list,
+				struct at_desc, desc_node);
+}
+
+static struct at_desc *atc_first_queued(struct at_dma_chan *atchan)
+{
+	return list_first_entry(&atchan->queue,
+				struct at_desc, desc_node);
+}
+
+/**
+ * atc_alloc_descriptor - allocate and return an initilized descriptor
+ * @chan: the channel to allocate descriptors for
+ * @gfp_flags: GFP allocation flags
+ *
+ * Note: The ack-bit is positioned in the descriptor flag at creation time
+ *       to make initial allocation more convenient. This bit will be cleared
+ *       and control will be given to client at usage time (during
+ *       preparation functions).
+ */
+static struct at_desc *atc_alloc_descriptor(struct dma_chan *chan,
+					    gfp_t gfp_flags)
+{
+	struct at_desc	*desc = NULL;
+	struct at_dma	*atdma = to_at_dma(chan->device);
+	dma_addr_t phys;
+
+	desc = dma_pool_alloc(atdma->dma_desc_pool, gfp_flags, &phys);
+	if (desc) {
+		memset(desc, 0, sizeof(struct at_desc));
+		dma_async_tx_descriptor_init(&desc->txd, chan);
+		/* txd.flags will be overwritten in prep functions */
+		desc->txd.flags = DMA_CTRL_ACK;
+		desc->txd.tx_submit = atc_tx_submit;
+		desc->txd.phys = phys;
+	}
+
+	return desc;
+}
+
+/**
+ * atc_desc_get - get a unsused descriptor from free_list
+ * @atchan: channel we want a new descriptor for
+ */
+static struct at_desc *atc_desc_get(struct at_dma_chan *atchan)
+{
+	struct at_desc *desc, *_desc;
+	struct at_desc *ret = NULL;
+	unsigned int i = 0;
+	LIST_HEAD(tmp_list);
+
+	spin_lock_bh(&atchan->lock);
+	list_for_each_entry_safe(desc, _desc, &atchan->free_list, desc_node) {
+		i++;
+		if (async_tx_test_ack(&desc->txd)) {
+			list_del(&desc->desc_node);
+			ret = desc;
+			break;
+		}
+		dev_dbg(chan2dev(&atchan->chan_common),
+				"desc %p not ACKed\n", desc);
+	}
+	spin_unlock_bh(&atchan->lock);
+	dev_vdbg(chan2dev(&atchan->chan_common),
+		"scanned %u descriptors on freelist\n", i);
+
+	/* no more descriptor available in initial pool: create one more */
+	if (!ret) {
+		ret = atc_alloc_descriptor(&atchan->chan_common, GFP_ATOMIC);
+		if (ret) {
+			spin_lock_bh(&atchan->lock);
+			atchan->descs_allocated++;
+			spin_unlock_bh(&atchan->lock);
+		} else {
+			dev_err(chan2dev(&atchan->chan_common),
+					"not enough descriptors available\n");
+		}
+	}
+
+	return ret;
+}
+
+/**
+ * atc_desc_put - move a descriptor, including any children, to the free list
+ * @atchan: channel we work on
+ * @desc: descriptor, at the head of a chain, to move to free list
+ */
+static void atc_desc_put(struct at_dma_chan *atchan, struct at_desc *desc)
+{
+	if (desc) {
+		struct at_desc *child;
+
+		spin_lock_bh(&atchan->lock);
+		list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+			dev_vdbg(chan2dev(&atchan->chan_common),
+					"moving child desc %p to freelist\n",
+					child);
+		list_splice_init(&desc->txd.tx_list, &atchan->free_list);
+		dev_vdbg(chan2dev(&atchan->chan_common),
+			 "moving desc %p to freelist\n", desc);
+		list_add(&desc->desc_node, &atchan->free_list);
+		spin_unlock_bh(&atchan->lock);
+	}
+}
+
+/**
+ * atc_assign_cookie - compute and assign new cookie
+ * @atchan: channel we work on
+ * @desc: descriptor to asign cookie for
+ *
+ * Called with atchan->lock held and bh disabled
+ */
+static dma_cookie_t
+atc_assign_cookie(struct at_dma_chan *atchan, struct at_desc *desc)
+{
+	dma_cookie_t cookie = atchan->chan_common.cookie;
+
+	if (++cookie < 0)
+		cookie = 1;
+
+	atchan->chan_common.cookie = cookie;
+	desc->txd.cookie = cookie;
+
+	return cookie;
+}
+
+/**
+ * atc_dostart - starts the DMA engine for real
+ * @atchan: the channel we want to start
+ * @first: first descriptor in the list we want to begin with
+ *
+ * Called with atchan->lock held and bh disabled
+ */
+static void atc_dostart(struct at_dma_chan *atchan, struct at_desc *first)
+{
+	struct at_dma	*atdma = to_at_dma(atchan->chan_common.device);
+
+	/* ASSERT:  channel is idle */
+	if (atc_chan_is_enabled(atchan)) {
+		dev_err(chan2dev(&atchan->chan_common),
+			"BUG: Attempted to start non-idle channel\n");
+		dev_err(chan2dev(&atchan->chan_common),
+			"  channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n",
+			channel_readl(atchan, SADDR),
+			channel_readl(atchan, DADDR),
+			channel_readl(atchan, CTRLA),
+			channel_readl(atchan, CTRLB),
+			channel_readl(atchan, DSCR));
+
+		/* The tasklet will hopefully advance the queue... */
+		return;
+	}
+
+	vdbg_dump_regs(atchan);
+
+	/* clear any pending interrupt */
+	while (dma_readl(atdma, EBCISR))
+		cpu_relax();
+
+	channel_writel(atchan, SADDR, 0);
+	channel_writel(atchan, DADDR, 0);
+	channel_writel(atchan, CTRLA, 0);
+	channel_writel(atchan, CTRLB, 0);
+	channel_writel(atchan, DSCR, first->txd.phys);
+	dma_writel(atdma, CHER, atchan->mask);
+
+	vdbg_dump_regs(atchan);
+}
+
+/**
+ * atc_chain_complete - finish work for one transaction chain
+ * @atchan: channel we work on
+ * @desc: descriptor at the head of the chain we want do complete
+ *
+ * Called with atchan->lock held and bh disabled */
+static void
+atc_chain_complete(struct at_dma_chan *atchan, struct at_desc *desc)
+{
+	dma_async_tx_callback		callback;
+	void				*param;
+	struct dma_async_tx_descriptor	*txd = &desc->txd;
+
+	dev_vdbg(chan2dev(&atchan->chan_common),
+		"descriptor %u complete\n", txd->cookie);
+
+	atchan->completed_cookie = txd->cookie;
+	callback = txd->callback;
+	param = txd->callback_param;
+
+	/* move children to free_list */
+	list_splice_init(&txd->tx_list, &atchan->free_list);
+	/* move myself to free_list */
+	list_move(&desc->desc_node, &atchan->free_list);
+
+	/* unmap dma addresses */
+	if (!(txd->flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
+		if (txd->flags & DMA_COMPL_DEST_UNMAP_SINGLE)
+			dma_unmap_single(chan2parent(&atchan->chan_common),
+					desc->lli.daddr,
+					desc->len, DMA_FROM_DEVICE);
+		else
+			dma_unmap_page(chan2parent(&atchan->chan_common),
+					desc->lli.daddr,
+					desc->len, DMA_FROM_DEVICE);
+	}
+	if (!(txd->flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
+		if (txd->flags & DMA_COMPL_SRC_UNMAP_SINGLE)
+			dma_unmap_single(chan2parent(&atchan->chan_common),
+					desc->lli.saddr,
+					desc->len, DMA_TO_DEVICE);
+		else
+			dma_unmap_page(chan2parent(&atchan->chan_common),
+					desc->lli.saddr,
+					desc->len, DMA_TO_DEVICE);
+	}
+
+	/*
+	 * The API requires that no submissions are done from a
+	 * callback, so we don't need to drop the lock here
+	 */
+	if (callback)
+		callback(param);
+
+	dma_run_dependencies(txd);
+}
+
+/**
+ * atc_complete_all - finish work for all transactions
+ * @atchan: channel to complete transactions for
+ *
+ * Eventually submit queued descriptors if any
+ *
+ * Assume channel is idle while calling this function
+ * Called with atchan->lock held and bh disabled
+ */
+static void atc_complete_all(struct at_dma_chan *atchan)
+{
+	struct at_desc *desc, *_desc;
+	LIST_HEAD(list);
+
+	dev_vdbg(chan2dev(&atchan->chan_common), "complete all\n");
+
+	BUG_ON(atc_chan_is_enabled(atchan));
+
+	/*
+	 * Submit queued descriptors ASAP, i.e. before we go through
+	 * the completed ones.
+	 */
+	if (!list_empty(&atchan->queue))
+		atc_dostart(atchan, atc_first_queued(atchan));
+	/* empty active_list now it is completed */
+	list_splice_init(&atchan->active_list, &list);
+	/* empty queue list by moving descriptors (if any) to active_list */
+	list_splice_init(&atchan->queue, &atchan->active_list);
+
+	list_for_each_entry_safe(desc, _desc, &list, desc_node)
+		atc_chain_complete(atchan, desc);
+}
+
+/**
+ * atc_cleanup_descriptors - cleanup up finished descriptors in active_list
+ * @atchan: channel to be cleaned up
+ *
+ * Called with atchan->lock held and bh disabled
+ */
+static void atc_cleanup_descriptors(struct at_dma_chan *atchan)
+{
+	struct at_desc	*desc, *_desc;
+	struct at_desc	*child;
+
+	dev_vdbg(chan2dev(&atchan->chan_common), "cleanup descriptors\n");
+
+	list_for_each_entry_safe(desc, _desc, &atchan->active_list, desc_node) {
+		if (!(desc->lli.ctrla & ATC_DONE))
+			/* This one is currently in progress */
+			return;
+
+		list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+			if (!(child->lli.ctrla & ATC_DONE))
+				/* Currently in progress */
+				return;
+
+		/*
+		 * No descriptors so far seem to be in progress, i.e.
+		 * this chain must be done.
+		 */
+		atc_chain_complete(atchan, desc);
+	}
+}
+
+/**
+ * atc_advance_work - at the end of a transaction, move forward
+ * @atchan: channel where the transaction ended
+ *
+ * Called with atchan->lock held and bh disabled
+ */
+static void atc_advance_work(struct at_dma_chan *atchan)
+{
+	dev_vdbg(chan2dev(&atchan->chan_common), "advance_work\n");
+
+	if (list_empty(&atchan->active_list) ||
+	    list_is_singular(&atchan->active_list)) {
+		atc_complete_all(atchan);
+	} else {
+		atc_chain_complete(atchan, atc_first_active(atchan));
+		/* advance work */
+		atc_dostart(atchan, atc_first_active(atchan));
+	}
+}
+
+
+/**
+ * atc_handle_error - handle errors reported by DMA controller
+ * @atchan: channel where error occurs
+ *
+ * Called with atchan->lock held and bh disabled
+ */
+static void atc_handle_error(struct at_dma_chan *atchan)
+{
+	struct at_desc *bad_desc;
+	struct at_desc *child;
+
+	/*
+	 * The descriptor currently at the head of the active list is
+	 * broked. Since we don't have any way to report errors, we'll
+	 * just have to scream loudly and try to carry on.
+	 */
+	bad_desc = atc_first_active(atchan);
+	list_del_init(&bad_desc->desc_node);
+
+	/* As we are stopped, take advantage to push queued descriptors
+	 * in active_list */
+	list_splice_init(&atchan->queue, atchan->active_list.prev);
+
+	/* Try to restart the controller */
+	if (!list_empty(&atchan->active_list))
+		atc_dostart(atchan, atc_first_active(atchan));
+
+	/*
+	 * KERN_CRITICAL may seem harsh, but since this only happens
+	 * when someone submits a bad physical address in a
+	 * descriptor, we should consider ourselves lucky that the
+	 * controller flagged an error instead of scribbling over
+	 * random memory locations.
+	 */
+	dev_crit(chan2dev(&atchan->chan_common),
+			"Bad descriptor submitted for DMA!\n");
+	dev_crit(chan2dev(&atchan->chan_common),
+			"  cookie: %d\n", bad_desc->txd.cookie);
+	atc_dump_lli(atchan, &bad_desc->lli);
+	list_for_each_entry(child, &bad_desc->txd.tx_list, desc_node)
+		atc_dump_lli(atchan, &child->lli);
+
+	/* Pretend the descriptor completed successfully */
+	atc_chain_complete(atchan, bad_desc);
+}
+
+
+/*--  IRQ & Tasklet  ---------------------------------------------------*/
+
+static void atc_tasklet(unsigned long data)
+{
+	struct at_dma_chan *atchan = (struct at_dma_chan *)data;
+
+	/* Channel cannot be enabled here */
+	if (atc_chan_is_enabled(atchan)) {
+		dev_err(chan2dev(&atchan->chan_common),
+			"BUG: channel enabled in tasklet\n");
+		return;
+	}
+
+	spin_lock(&atchan->lock);
+	if (test_and_clear_bit(0, &atchan->error_status))
+		atc_handle_error(atchan);
+	else
+		atc_advance_work(atchan);
+
+	spin_unlock(&atchan->lock);
+}
+
+static irqreturn_t at_dma_interrupt(int irq, void *dev_id)
+{
+	struct at_dma		*atdma = (struct at_dma *)dev_id;
+	struct at_dma_chan	*atchan;
+	int			i;
+	u32			status, pending, imr;
+	int			ret = IRQ_NONE;
+
+	do {
+		imr = dma_readl(atdma, EBCIMR);
+		status = dma_readl(atdma, EBCISR);
+		pending = status & imr;
+
+		if (!pending)
+			break;
+
+		dev_vdbg(atdma->dma_common.dev,
+			"interrupt: status = 0x%08x, 0x%08x, 0x%08x\n",
+			 status, imr, pending);
+
+		for (i = 0; i < atdma->dma_common.chancnt; i++) {
+			atchan = &atdma->chan[i];
+			if (pending & (AT_DMA_CBTC(i) | AT_DMA_ERR(i))) {
+				if (pending & AT_DMA_ERR(i)) {
+					/* Disable channel on AHB error */
+					dma_writel(atdma, CHDR, atchan->mask);
+					/* Give information to tasklet */
+					set_bit(0, &atchan->error_status);
+				}
+				tasklet_schedule(&atchan->tasklet);
+				ret = IRQ_HANDLED;
+			}
+		}
+
+	} while (pending);
+
+	return ret;
+}
+
+
+/*--  DMA Engine API  --------------------------------------------------*/
+
+/**
+ * atc_tx_submit - set the prepared descriptor(s) to be executed by the engine
+ * @desc: descriptor at the head of the transaction chain
+ *
+ * Queue chain if DMA engine is working already
+ *
+ * Cookie increment and adding to active_list or queue must be atomic
+ */
+static dma_cookie_t atc_tx_submit(struct dma_async_tx_descriptor *tx)
+{
+	struct at_desc		*desc = txd_to_at_desc(tx);
+	struct at_dma_chan	*atchan = to_at_dma_chan(tx->chan);
+	dma_cookie_t		cookie;
+
+	spin_lock_bh(&atchan->lock);
+	cookie = atc_assign_cookie(atchan, desc);
+
+	if (list_empty(&atchan->active_list)) {
+		dev_vdbg(chan2dev(tx->chan), "tx_submit: started %u\n",
+				desc->txd.cookie);
+		atc_dostart(atchan, desc);
+		list_add_tail(&desc->desc_node, &atchan->active_list);
+	} else {
+		dev_vdbg(chan2dev(tx->chan), "tx_submit: queued %u\n",
+				desc->txd.cookie);
+		list_add_tail(&desc->desc_node, &atchan->queue);
+	}
+
+	spin_unlock_bh(&atchan->lock);
+
+	return cookie;
+}
+
+/**
+ * atc_prep_dma_memcpy - prepare a memcpy operation
+ * @chan: the channel to prepare operation on
+ * @dest: operation virtual destination address
+ * @src: operation virtual source address
+ * @len: operation length
+ * @flags: tx descriptor status flags
+ */
+static struct dma_async_tx_descriptor *
+atc_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
+		size_t len, unsigned long flags)
+{
+	struct at_dma_chan	*atchan = to_at_dma_chan(chan);
+	struct at_desc		*desc = NULL;
+	struct at_desc		*first = NULL;
+	struct at_desc		*prev = NULL;
+	size_t			xfer_count;
+	size_t			offset;
+	unsigned int		src_width;
+	unsigned int		dst_width;
+	u32			ctrla;
+	u32			ctrlb;
+
+	dev_vdbg(chan2dev(chan), "prep_dma_memcpy: d0x%x s0x%x l0x%zx f0x%lx\n",
+			dest, src, len, flags);
+
+	if (unlikely(!len)) {
+		dev_dbg(chan2dev(chan), "prep_dma_memcpy: length is zero!\n");
+		return NULL;
+	}
+
+	ctrla =   ATC_DEFAULT_CTRLA;
+	ctrlb =   ATC_DEFAULT_CTRLB
+		| ATC_SRC_ADDR_MODE_INCR
+		| ATC_DST_ADDR_MODE_INCR
+		| ATC_FC_MEM2MEM;
+
+	/*
+	 * We can be a lot more clever here, but this should take care
+	 * of the most common optimization.
+	 */
+	if (!((src | dest  | len) & 3)) {
+		ctrla |= ATC_SRC_WIDTH_WORD | ATC_DST_WIDTH_WORD;
+		src_width = dst_width = 2;
+	} else if (!((src | dest | len) & 1)) {
+		ctrla |= ATC_SRC_WIDTH_HALFWORD | ATC_DST_WIDTH_HALFWORD;
+		src_width = dst_width = 1;
+	} else {
+		ctrla |= ATC_SRC_WIDTH_BYTE | ATC_DST_WIDTH_BYTE;
+		src_width = dst_width = 0;
+	}
+
+	for (offset = 0; offset < len; offset += xfer_count << src_width) {
+		xfer_count = min_t(size_t, (len - offset) >> src_width,
+				ATC_BTSIZE_MAX);
+
+		desc = atc_desc_get(atchan);
+		if (!desc)
+			goto err_desc_get;
+
+		desc->lli.saddr = src + offset;
+		desc->lli.daddr = dest + offset;
+		desc->lli.ctrla = ctrla | xfer_count;
+		desc->lli.ctrlb = ctrlb;
+
+		desc->txd.cookie = 0;
+		async_tx_ack(&desc->txd);
+
+		if (!first) {
+			first = desc;
+		} else {
+			/* inform the HW lli about chaining */
+			prev->lli.dscr = desc->txd.phys;
+			/* insert the link descriptor to the LD ring */
+			list_add_tail(&desc->desc_node,
+					&first->txd.tx_list);
+		}
+		prev = desc;
+	}
+
+	/* First descriptor of the chain embedds additional information */
+	first->txd.cookie = -EBUSY;
+	first->len = len;
+
+	/* set end-of-link to the last link descriptor of list*/
+	set_desc_eol(desc);
+
+	desc->txd.flags = flags; /* client is in control of this ack */
+
+	return &first->txd;
+
+err_desc_get:
+	atc_desc_put(atchan, first);
+	return NULL;
+}
+
+/**
+ * atc_is_tx_complete - poll for transaction completion
+ * @chan: DMA channel
+ * @cookie: transaction identifier to check status of
+ * @done: if not %NULL, updated with last completed transaction
+ * @used: if not %NULL, updated with last used transaction
+ *
+ * If @done and @used are passed in, upon return they reflect the driver
+ * internal state and can be used with dma_async_is_complete() to check
+ * the status of multiple cookies without re-checking hardware state.
+ */
+static enum dma_status
+atc_is_tx_complete(struct dma_chan *chan,
+		dma_cookie_t cookie,
+		dma_cookie_t *done, dma_cookie_t *used)
+{
+	struct at_dma_chan	*atchan = to_at_dma_chan(chan);
+	dma_cookie_t		last_used;
+	dma_cookie_t		last_complete;
+	enum dma_status		ret;
+
+	dev_vdbg(chan2dev(chan), "is_tx_complete: %d (d%d, u%d)\n",
+			cookie, done ? *done : 0, used ? *used : 0);
+
+	spin_lock_bh(atchan->lock);
+
+	last_complete = atchan->completed_cookie;
+	last_used = chan->cookie;
+
+	ret = dma_async_is_complete(cookie, last_complete, last_used);
+	if (ret != DMA_SUCCESS) {
+		atc_cleanup_descriptors(atchan);
+
+		last_complete = atchan->completed_cookie;
+		last_used = chan->cookie;
+
+		ret = dma_async_is_complete(cookie, last_complete, last_used);
+	}
+
+	spin_unlock_bh(atchan->lock);
+
+	if (done)
+		*done = last_complete;
+	if (used)
+		*used = last_used;
+
+	return ret;
+}
+
+/**
+ * atc_issue_pending - try to finish work
+ * @chan: target DMA channel
+ */
+static void atc_issue_pending(struct dma_chan *chan)
+{
+	struct at_dma_chan	*atchan = to_at_dma_chan(chan);
+
+	dev_vdbg(chan2dev(chan), "issue_pending\n");
+
+	if (!atc_chan_is_enabled(atchan)) {
+		spin_lock_bh(&atchan->lock);
+		atc_advance_work(atchan);
+		spin_unlock_bh(&atchan->lock);
+	}
+}
+
+/**
+ * atc_alloc_chan_resources - allocate resources for DMA channel
+ * @chan: allocate descriptor resources for this channel
+ * @client: current client requesting the channel be ready for requests
+ *
+ * return - the number of allocated descriptors
+ */
+static int atc_alloc_chan_resources(struct dma_chan *chan)
+{
+	struct at_dma_chan	*atchan = to_at_dma_chan(chan);
+	struct at_dma		*atdma = to_at_dma(chan->device);
+	struct at_desc		*desc;
+	int			i;
+	LIST_HEAD(tmp_list);
+
+	dev_vdbg(chan2dev(chan), "alloc_chan_resources\n");
+
+	/* ASSERT:  channel is idle */
+	if (atc_chan_is_enabled(atchan)) {
+		dev_dbg(chan2dev(chan), "DMA channel not idle ?\n");
+		return -EIO;
+	}
+
+	/* have we already been set up? */
+	if (!list_empty(&atchan->free_list))
+		return atchan->descs_allocated;
+
+	/* Allocate initial pool of descriptors */
+	for (i = 0; i < init_nr_desc_per_channel; i++) {
+		desc = atc_alloc_descriptor(chan, GFP_KERNEL);
+		if (!desc) {
+			dev_err(atdma->dma_common.dev,
+				"Only %d initial descriptors\n", i);
+			break;
+		}
+		list_add_tail(&desc->desc_node, &tmp_list);
+	}
+
+	spin_lock_bh(&atchan->lock);
+	atchan->descs_allocated = i;
+	list_splice(&tmp_list, &atchan->free_list);
+	atchan->completed_cookie = chan->cookie = 1;
+	spin_unlock_bh(&atchan->lock);
+
+	/* channel parameters */
+	channel_writel(atchan, CFG, ATC_DEFAULT_CFG);
+
+	dev_dbg(chan2dev(chan),
+		"alloc_chan_resources: allocated %d descriptors\n",
+		atchan->descs_allocated);
+
+	return atchan->descs_allocated;
+}
+
+/**
+ * atc_free_chan_resources - free all channel resources
+ * @chan: DMA channel
+ */
+static void atc_free_chan_resources(struct dma_chan *chan)
+{
+	struct at_dma_chan	*atchan = to_at_dma_chan(chan);
+	struct at_dma		*atdma = to_at_dma(chan->device);
+	struct at_desc		*desc, *_desc;
+	LIST_HEAD(list);
+
+	dev_dbg(chan2dev(chan), "free_chan_resources: (descs allocated=%u)\n",
+		atchan->descs_allocated);
+
+	/* ASSERT:  channel is idle */
+	BUG_ON(!list_empty(&atchan->active_list));
+	BUG_ON(!list_empty(&atchan->queue));
+	BUG_ON(atc_chan_is_enabled(atchan));
+
+	list_for_each_entry_safe(desc, _desc, &atchan->free_list, desc_node) {
+		dev_vdbg(chan2dev(chan), "  freeing descriptor %p\n", desc);
+		list_del(&desc->desc_node);
+		/* free link descriptor */
+		dma_pool_free(atdma->dma_desc_pool, desc, desc->txd.phys);
+	}
+	list_splice_init(&atchan->free_list, &list);
+	atchan->descs_allocated = 0;
+
+	dev_vdbg(chan2dev(chan), "free_chan_resources: done\n");
+}
+
+
+/*--  Module Management  -----------------------------------------------*/
+
+/**
+ * at_dma_off - disable DMA controller
+ * @atdma: the Atmel HDAMC device
+ */
+static void at_dma_off(struct at_dma *atdma)
+{
+	dma_writel(atdma, EN, 0);
+
+	/* disable all interrupts */
+	dma_writel(atdma, EBCIDR, -1L);
+
+	/* confirm that all channels are disabled */
+	while (dma_readl(atdma, CHSR) & atdma->all_chan_mask)
+		cpu_relax();
+}
+
+static int __init at_dma_probe(struct platform_device *pdev)
+{
+	struct at_dma_platform_data *pdata;
+	struct resource		*io;
+	struct at_dma		*atdma;
+	size_t			size;
+	int			irq;
+	int			err;
+	int			i;
+
+	/* get DMA Controller parameters from platform */
+	pdata = pdev->dev.platform_data;
+	if (!pdata || pdata->nr_channels > AT_DMA_MAX_NR_CHANNELS)
+		return -EINVAL;
+
+	io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!io)
+		return -EINVAL;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	size = sizeof(struct at_dma);
+	size += pdata->nr_channels * sizeof(struct at_dma_chan);
+	atdma = kzalloc(size, GFP_KERNEL);
+	if (!atdma)
+		return -ENOMEM;
+
+	/* discover transaction capabilites from the platform data */
+	atdma->dma_common.cap_mask = pdata->cap_mask;
+	atdma->all_chan_mask = (1 << pdata->nr_channels) - 1;
+
+	size = io->end - io->start + 1;
+	if (!request_mem_region(io->start, size, pdev->dev.driver->name)) {
+		err = -EBUSY;
+		goto err_kfree;
+	}
+
+	atdma->regs = ioremap(io->start, size);
+	if (!atdma->regs) {
+		err = -ENOMEM;
+		goto err_release_r;
+	}
+
+	atdma->clk = clk_get(&pdev->dev, "dma_clk");
+	if (IS_ERR(atdma->clk)) {
+		err = PTR_ERR(atdma->clk);
+		goto err_clk;
+	}
+	clk_enable(atdma->clk);
+
+	/* force dma off, just in case */
+	at_dma_off(atdma);
+
+	err = request_irq(irq, at_dma_interrupt, 0, "at_hdmac", atdma);
+	if (err)
+		goto err_irq;
+
+	platform_set_drvdata(pdev, atdma);
+
+	/* create a pool of consistent memory blocks for hardware descriptors */
+	atdma->dma_desc_pool = dma_pool_create("at_hdmac_desc_pool",
+			&pdev->dev, sizeof(struct at_desc),
+			4 /* word alignment */, 0);
+	if (!atdma->dma_desc_pool) {
+		dev_err(&pdev->dev, "No memory for descriptors dma pool\n");
+		err = -ENOMEM;
+		goto err_pool_create;
+	}
+
+	/* clear any pending interrupt */
+	while (dma_readl(atdma, EBCISR))
+		cpu_relax();
+
+	/* initialize channels related values */
+	INIT_LIST_HEAD(&atdma->dma_common.channels);
+	for (i = 0; i < pdata->nr_channels; i++, atdma->dma_common.chancnt++) {
+		struct at_dma_chan	*atchan = &atdma->chan[i];
+
+		atchan->chan_common.device = &atdma->dma_common;
+		atchan->chan_common.cookie = atchan->completed_cookie = 1;
+		atchan->chan_common.chan_id = i;
+		list_add_tail(&atchan->chan_common.device_node,
+				&atdma->dma_common.channels);
+
+		atchan->ch_regs = atdma->regs + ch_regs(i);
+		spin_lock_init(&atchan->lock);
+		atchan->mask = 1 << i;
+
+		INIT_LIST_HEAD(&atchan->active_list);
+		INIT_LIST_HEAD(&atchan->queue);
+		INIT_LIST_HEAD(&atchan->free_list);
+
+		tasklet_init(&atchan->tasklet, atc_tasklet,
+				(unsigned long)atchan);
+		atc_enable_irq(atchan);
+	}
+
+	/* set base routines */
+	atdma->dma_common.device_alloc_chan_resources = atc_alloc_chan_resources;
+	atdma->dma_common.device_free_chan_resources = atc_free_chan_resources;
+	atdma->dma_common.device_is_tx_complete = atc_is_tx_complete;
+	atdma->dma_common.device_issue_pending = atc_issue_pending;
+	atdma->dma_common.dev = &pdev->dev;
+
+	/* set prep routines based on capability */
+	if (dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask))
+		atdma->dma_common.device_prep_dma_memcpy = atc_prep_dma_memcpy;
+
+	dma_writel(atdma, EN, AT_DMA_ENABLE);
+
+	dev_info(&pdev->dev, "Atmel AHB DMA Controller ( %s%s), %d channels\n",
+	  dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask) ? "cpy " : "",
+	  dma_has_cap(DMA_SLAVE, atdma->dma_common.cap_mask)  ? "slave " : "",
+	  atdma->dma_common.chancnt);
+
+	dma_async_device_register(&atdma->dma_common);
+
+	return 0;
+
+err_pool_create:
+	platform_set_drvdata(pdev, NULL);
+	free_irq(platform_get_irq(pdev, 0), atdma);
+err_irq:
+	clk_disable(atdma->clk);
+	clk_put(atdma->clk);
+err_clk:
+	iounmap(atdma->regs);
+	atdma->regs = NULL;
+err_release_r:
+	release_mem_region(io->start, size);
+err_kfree:
+	kfree(atdma);
+	return err;
+}
+
+static int __exit at_dma_remove(struct platform_device *pdev)
+{
+	struct at_dma		*atdma = platform_get_drvdata(pdev);
+	struct dma_chan		*chan, *_chan;
+	struct resource		*io;
+
+	at_dma_off(atdma);
+	dma_async_device_unregister(&atdma->dma_common);
+
+	dma_pool_destroy(atdma->dma_desc_pool);
+	platform_set_drvdata(pdev, NULL);
+	free_irq(platform_get_irq(pdev, 0), atdma);
+
+	list_for_each_entry_safe(chan, _chan, &atdma->dma_common.channels,
+			device_node) {
+		struct at_dma_chan	*atchan = to_at_dma_chan(chan);
+
+		/* Disable interrupts */
+		atc_disable_irq(atchan);
+		tasklet_disable(&atchan->tasklet);
+
+		tasklet_kill(&atchan->tasklet);
+		list_del(&chan->device_node);
+	}
+
+	clk_disable(atdma->clk);
+	clk_put(atdma->clk);
+
+	iounmap(atdma->regs);
+	atdma->regs = NULL;
+
+	io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	release_mem_region(io->start, io->end - io->start + 1);
+
+	kfree(atdma);
+
+	return 0;
+}
+
+static void at_dma_shutdown(struct platform_device *pdev)
+{
+	struct at_dma	*atdma = platform_get_drvdata(pdev);
+
+	at_dma_off(platform_get_drvdata(pdev));
+	clk_disable(atdma->clk);
+}
+
+static int at_dma_suspend_late(struct platform_device *pdev, pm_message_t mesg)
+{
+	struct at_dma	*atdma = platform_get_drvdata(pdev);
+
+	at_dma_off(platform_get_drvdata(pdev));
+	clk_disable(atdma->clk);
+	return 0;
+}
+
+static int at_dma_resume_early(struct platform_device *pdev)
+{
+	struct at_dma	*atdma = platform_get_drvdata(pdev);
+
+	clk_enable(atdma->clk);
+	dma_writel(atdma, EN, AT_DMA_ENABLE);
+	return 0;
+
+}
+
+static struct platform_driver at_dma_driver = {
+	.remove		= __exit_p(at_dma_remove),
+	.shutdown	= at_dma_shutdown,
+	.suspend_late	= at_dma_suspend_late,
+	.resume_early	= at_dma_resume_early,
+	.driver = {
+		.name	= "at_hdmac",
+	},
+};
+
+static int __init at_dma_init(void)
+{
+	return platform_driver_probe(&at_dma_driver, at_dma_probe);
+}
+module_init(at_dma_init);
+
+static void __exit at_dma_exit(void)
+{
+	platform_driver_unregister(&at_dma_driver);
+}
+module_exit(at_dma_exit);
+
+MODULE_DESCRIPTION("Atmel AHB DMA Controller driver");
+MODULE_AUTHOR("Nicolas Ferre <nicolas.ferre@atmel.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:at_hdmac");
diff --git a/drivers/dma/at_hdmac_regs.h b/drivers/dma/at_hdmac_regs.h
new file mode 100644
index 00000000000..ad2d4f402bf
--- /dev/null
+++ b/drivers/dma/at_hdmac_regs.h
@@ -0,0 +1,386 @@
+/*
+ * Header file for the Atmel AHB DMA Controller driver
+ *
+ * Copyright (C) 2008 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef AT_HDMAC_REGS_H
+#define	AT_HDMAC_REGS_H
+
+#include <mach/at_hdmac.h>
+
+#define	AT_DMA_MAX_NR_CHANNELS	8
+
+
+#define	AT_DMA_GCFG	0x00	/* Global Configuration Register */
+#define		AT_DMA_IF_BIGEND(i)	(0x1 << (i))	/* AHB-Lite Interface i in Big-endian mode */
+#define		AT_DMA_ARB_CFG	(0x1 << 4)	/* Arbiter mode. */
+#define			AT_DMA_ARB_CFG_FIXED		(0x0 << 4)
+#define			AT_DMA_ARB_CFG_ROUND_ROBIN	(0x1 << 4)
+
+#define	AT_DMA_EN	0x04	/* Controller Enable Register */
+#define		AT_DMA_ENABLE	(0x1 << 0)
+
+#define	AT_DMA_SREQ	0x08	/* Software Single Request Register */
+#define		AT_DMA_SSREQ(x)	(0x1 << ((x) << 1))		/* Request a source single transfer on channel x */
+#define		AT_DMA_DSREQ(x)	(0x1 << (1 + ((x) << 1)))	/* Request a destination single transfer on channel x */
+
+#define	AT_DMA_CREQ	0x0C	/* Software Chunk Transfer Request Register */
+#define		AT_DMA_SCREQ(x)	(0x1 << ((x) << 1))		/* Request a source chunk transfer on channel x */
+#define		AT_DMA_DCREQ(x)	(0x1 << (1 + ((x) << 1)))	/* Request a destination chunk transfer on channel x */
+
+#define	AT_DMA_LAST	0x10	/* Software Last Transfer Flag Register */
+#define		AT_DMA_SLAST(x)	(0x1 << ((x) << 1))		/* This src rq is last tx of buffer on channel x */
+#define		AT_DMA_DLAST(x)	(0x1 << (1 + ((x) << 1)))	/* This dst rq is last tx of buffer on channel x */
+
+#define	AT_DMA_SYNC	0x14	/* Request Synchronization Register */
+#define		AT_DMA_SYR(h)	(0x1 << (h))			/* Synchronize handshake line h */
+
+/* Error, Chained Buffer transfer completed and Buffer transfer completed Interrupt registers */
+#define	AT_DMA_EBCIER	0x18	/* Enable register */
+#define	AT_DMA_EBCIDR	0x1C	/* Disable register */
+#define	AT_DMA_EBCIMR	0x20	/* Mask Register */
+#define	AT_DMA_EBCISR	0x24	/* Status Register */
+#define		AT_DMA_CBTC_OFFSET	8
+#define		AT_DMA_ERR_OFFSET	16
+#define		AT_DMA_BTC(x)	(0x1 << (x))
+#define		AT_DMA_CBTC(x)	(0x1 << (AT_DMA_CBTC_OFFSET + (x)))
+#define		AT_DMA_ERR(x)	(0x1 << (AT_DMA_ERR_OFFSET + (x)))
+
+#define	AT_DMA_CHER	0x28	/* Channel Handler Enable Register */
+#define		AT_DMA_ENA(x)	(0x1 << (x))
+#define		AT_DMA_SUSP(x)	(0x1 << ( 8 + (x)))
+#define		AT_DMA_KEEP(x)	(0x1 << (24 + (x)))
+
+#define	AT_DMA_CHDR	0x2C	/* Channel Handler Disable Register */
+#define		AT_DMA_DIS(x)	(0x1 << (x))
+#define		AT_DMA_RES(x)	(0x1 << ( 8 + (x)))
+
+#define	AT_DMA_CHSR	0x30	/* Channel Handler Status Register */
+#define		AT_DMA_EMPT(x)	(0x1 << (16 + (x)))
+#define		AT_DMA_STAL(x)	(0x1 << (24 + (x)))
+
+
+#define	AT_DMA_CH_REGS_BASE	0x3C	/* Channel registers base address */
+#define	ch_regs(x)	(AT_DMA_CH_REGS_BASE + (x) * 0x28) /* Channel x base addr */
+
+/* Hardware register offset for each channel */
+#define	ATC_SADDR_OFFSET	0x00	/* Source Address Register */
+#define	ATC_DADDR_OFFSET	0x04	/* Destination Address Register */
+#define	ATC_DSCR_OFFSET		0x08	/* Descriptor Address Register */
+#define	ATC_CTRLA_OFFSET	0x0C	/* Control A Register */
+#define	ATC_CTRLB_OFFSET	0x10	/* Control B Register */
+#define	ATC_CFG_OFFSET		0x14	/* Configuration Register */
+#define	ATC_SPIP_OFFSET		0x18	/* Src PIP Configuration Register */
+#define	ATC_DPIP_OFFSET		0x1C	/* Dst PIP Configuration Register */
+
+
+/* Bitfield definitions */
+
+/* Bitfields in DSCR */
+#define	ATC_DSCR_IF(i)		(0x3 & (i))	/* Dsc feched via AHB-Lite Interface i */
+
+/* Bitfields in CTRLA */
+#define	ATC_BTSIZE_MAX		0xFFFFUL	/* Maximum Buffer Transfer Size */
+#define	ATC_BTSIZE(x)		(ATC_BTSIZE_MAX & (x)) /* Buffer Transfer Size */
+#define	ATC_SCSIZE_MASK		(0x7 << 16)	/* Source Chunk Transfer Size */
+#define		ATC_SCSIZE_1		(0x0 << 16)
+#define		ATC_SCSIZE_4		(0x1 << 16)
+#define		ATC_SCSIZE_8		(0x2 << 16)
+#define		ATC_SCSIZE_16		(0x3 << 16)
+#define		ATC_SCSIZE_32		(0x4 << 16)
+#define		ATC_SCSIZE_64		(0x5 << 16)
+#define		ATC_SCSIZE_128		(0x6 << 16)
+#define		ATC_SCSIZE_256		(0x7 << 16)
+#define	ATC_DCSIZE_MASK		(0x7 << 20)	/* Destination Chunk Transfer Size */
+#define		ATC_DCSIZE_1		(0x0 << 20)
+#define		ATC_DCSIZE_4		(0x1 << 20)
+#define		ATC_DCSIZE_8		(0x2 << 20)
+#define		ATC_DCSIZE_16		(0x3 << 20)
+#define		ATC_DCSIZE_32		(0x4 << 20)
+#define		ATC_DCSIZE_64		(0x5 << 20)
+#define		ATC_DCSIZE_128		(0x6 << 20)
+#define		ATC_DCSIZE_256		(0x7 << 20)
+#define	ATC_SRC_WIDTH_MASK	(0x3 << 24)	/* Source Single Transfer Size */
+#define		ATC_SRC_WIDTH_BYTE	(0x0 << 24)
+#define		ATC_SRC_WIDTH_HALFWORD	(0x1 << 24)
+#define		ATC_SRC_WIDTH_WORD	(0x2 << 24)
+#define	ATC_DST_WIDTH_MASK	(0x3 << 28)	/* Destination Single Transfer Size */
+#define		ATC_DST_WIDTH_BYTE	(0x0 << 28)
+#define		ATC_DST_WIDTH_HALFWORD	(0x1 << 28)
+#define		ATC_DST_WIDTH_WORD	(0x2 << 28)
+#define	ATC_DONE		(0x1 << 31)	/* Tx Done (only written back in descriptor) */
+
+/* Bitfields in CTRLB */
+#define	ATC_SIF(i)		(0x3 & (i))	/* Src tx done via AHB-Lite Interface i */
+#define	ATC_DIF(i)		((0x3 & (i)) <<  4)	/* Dst tx done via AHB-Lite Interface i */
+#define	ATC_SRC_PIP		(0x1 <<  8)	/* Source Picture-in-Picture enabled */
+#define	ATC_DST_PIP		(0x1 << 12)	/* Destination Picture-in-Picture enabled */
+#define	ATC_SRC_DSCR_DIS	(0x1 << 16)	/* Src Descriptor fetch disable */
+#define	ATC_DST_DSCR_DIS	(0x1 << 20)	/* Dst Descriptor fetch disable */
+#define	ATC_FC_MASK		(0x7 << 21)	/* Choose Flow Controller */
+#define		ATC_FC_MEM2MEM		(0x0 << 21)	/* Mem-to-Mem (DMA) */
+#define		ATC_FC_MEM2PER		(0x1 << 21)	/* Mem-to-Periph (DMA) */
+#define		ATC_FC_PER2MEM		(0x2 << 21)	/* Periph-to-Mem (DMA) */
+#define		ATC_FC_PER2PER		(0x3 << 21)	/* Periph-to-Periph (DMA) */
+#define		ATC_FC_PER2MEM_PER	(0x4 << 21)	/* Periph-to-Mem (Peripheral) */
+#define		ATC_FC_MEM2PER_PER	(0x5 << 21)	/* Mem-to-Periph (Peripheral) */
+#define		ATC_FC_PER2PER_PER	(0x6 << 21)	/* Periph-to-Periph (Src Peripheral) */
+#define	ATC_SRC_ADDR_MODE_MASK	(0x3 << 24)
+#define		ATC_SRC_ADDR_MODE_INCR	(0x0 << 24)	/* Incrementing Mode */
+#define		ATC_SRC_ADDR_MODE_DECR	(0x1 << 24)	/* Decrementing Mode */
+#define		ATC_SRC_ADDR_MODE_FIXED	(0x2 << 24)	/* Fixed Mode */
+#define	ATC_DST_ADDR_MODE_MASK	(0x3 << 28)
+#define		ATC_DST_ADDR_MODE_INCR	(0x0 << 28)	/* Incrementing Mode */
+#define		ATC_DST_ADDR_MODE_DECR	(0x1 << 28)	/* Decrementing Mode */
+#define		ATC_DST_ADDR_MODE_FIXED	(0x2 << 28)	/* Fixed Mode */
+#define	ATC_IEN			(0x1 << 30)	/* BTC interrupt enable (active low) */
+#define	ATC_AUTO		(0x1 << 31)	/* Auto multiple buffer tx enable */
+
+/* Bitfields in CFG */
+#define	ATC_SRC_PER(h)		(0xFU & (h))	/* Channel src rq associated with periph handshaking ifc h */
+#define	ATC_DST_PER(h)		((0xFU & (h)) <<  4)	/* Channel dst rq associated with periph handshaking ifc h */
+#define	ATC_SRC_REP		(0x1 <<  8)	/* Source Replay Mod */
+#define	ATC_SRC_H2SEL		(0x1 <<  9)	/* Source Handshaking Mod */
+#define		ATC_SRC_H2SEL_SW	(0x0 <<  9)
+#define		ATC_SRC_H2SEL_HW	(0x1 <<  9)
+#define	ATC_DST_REP		(0x1 << 12)	/* Destination Replay Mod */
+#define	ATC_DST_H2SEL		(0x1 << 13)	/* Destination Handshaking Mod */
+#define		ATC_DST_H2SEL_SW	(0x0 << 13)
+#define		ATC_DST_H2SEL_HW	(0x1 << 13)
+#define	ATC_SOD			(0x1 << 16)	/* Stop On Done */
+#define	ATC_LOCK_IF		(0x1 << 20)	/* Interface Lock */
+#define	ATC_LOCK_B		(0x1 << 21)	/* AHB Bus Lock */
+#define	ATC_LOCK_IF_L		(0x1 << 22)	/* Master Interface Arbiter Lock */
+#define		ATC_LOCK_IF_L_CHUNK	(0x0 << 22)
+#define		ATC_LOCK_IF_L_BUFFER	(0x1 << 22)
+#define	ATC_AHB_PROT_MASK	(0x7 << 24)	/* AHB Protection */
+#define	ATC_FIFOCFG_MASK	(0x3 << 28)	/* FIFO Request Configuration */
+#define		ATC_FIFOCFG_LARGESTBURST	(0x0 << 28)
+#define		ATC_FIFOCFG_HALFFIFO		(0x1 << 28)
+#define		ATC_FIFOCFG_ENOUGHSPACE		(0x2 << 28)
+
+/* Bitfields in SPIP */
+#define	ATC_SPIP_HOLE(x)	(0xFFFFU & (x))
+#define	ATC_SPIP_BOUNDARY(x)	((0x3FF & (x)) << 16)
+
+/* Bitfields in DPIP */
+#define	ATC_DPIP_HOLE(x)	(0xFFFFU & (x))
+#define	ATC_DPIP_BOUNDARY(x)	((0x3FF & (x)) << 16)
+
+
+/*--  descriptors  -----------------------------------------------------*/
+
+/* LLI == Linked List Item; aka DMA buffer descriptor */
+struct at_lli {
+	/* values that are not changed by hardware */
+	dma_addr_t	saddr;
+	dma_addr_t	daddr;
+	/* value that may get written back: */
+	u32		ctrla;
+	/* more values that are not changed by hardware */
+	u32		ctrlb;
+	dma_addr_t	dscr;	/* chain to next lli */
+};
+
+/**
+ * struct at_desc - software descriptor
+ * @at_lli: hardware lli structure
+ * @txd: support for the async_tx api
+ * @desc_node: node on the channed descriptors list
+ * @len: total transaction bytecount
+ */
+struct at_desc {
+	/* FIRST values the hardware uses */
+	struct at_lli			lli;
+
+	/* THEN values for driver housekeeping */
+	struct dma_async_tx_descriptor	txd;
+	struct list_head		desc_node;
+	size_t				len;
+};
+
+static inline struct at_desc *
+txd_to_at_desc(struct dma_async_tx_descriptor *txd)
+{
+	return container_of(txd, struct at_desc, txd);
+}
+
+
+/*--  Channels  --------------------------------------------------------*/
+
+/**
+ * struct at_dma_chan - internal representation of an Atmel HDMAC channel
+ * @chan_common: common dmaengine channel object members
+ * @device: parent device
+ * @ch_regs: memory mapped register base
+ * @mask: channel index in a mask
+ * @error_status: transmit error status information from irq handler
+ *                to tasklet (use atomic operations)
+ * @tasklet: bottom half to finish transaction work
+ * @lock: serializes enqueue/dequeue operations to descriptors lists
+ * @completed_cookie: identifier for the most recently completed operation
+ * @active_list: list of descriptors dmaengine is being running on
+ * @queue: list of descriptors ready to be submitted to engine
+ * @free_list: list of descriptors usable by the channel
+ * @descs_allocated: records the actual size of the descriptor pool
+ */
+struct at_dma_chan {
+	struct dma_chan		chan_common;
+	struct at_dma		*device;
+	void __iomem		*ch_regs;
+	u8			mask;
+	unsigned long		error_status;
+	struct tasklet_struct	tasklet;
+
+	spinlock_t		lock;
+
+	/* these other elements are all protected by lock */
+	dma_cookie_t		completed_cookie;
+	struct list_head	active_list;
+	struct list_head	queue;
+	struct list_head	free_list;
+	unsigned int		descs_allocated;
+};
+
+#define	channel_readl(atchan, name) \
+	__raw_readl((atchan)->ch_regs + ATC_##name##_OFFSET)
+
+#define	channel_writel(atchan, name, val) \
+	__raw_writel((val), (atchan)->ch_regs + ATC_##name##_OFFSET)
+
+static inline struct at_dma_chan *to_at_dma_chan(struct dma_chan *dchan)
+{
+	return container_of(dchan, struct at_dma_chan, chan_common);
+}
+
+
+/*--  Controller  ------------------------------------------------------*/
+
+/**
+ * struct at_dma - internal representation of an Atmel HDMA Controller
+ * @chan_common: common dmaengine dma_device object members
+ * @ch_regs: memory mapped register base
+ * @clk: dma controller clock
+ * @all_chan_mask: all channels availlable in a mask
+ * @dma_desc_pool: base of DMA descriptor region (DMA address)
+ * @chan: channels table to store at_dma_chan structures
+ */
+struct at_dma {
+	struct dma_device	dma_common;
+	void __iomem		*regs;
+	struct clk		*clk;
+
+	u8			all_chan_mask;
+
+	struct dma_pool		*dma_desc_pool;
+	/* AT THE END channels table */
+	struct at_dma_chan	chan[0];
+};
+
+#define	dma_readl(atdma, name) \
+	__raw_readl((atdma)->regs + AT_DMA_##name)
+#define	dma_writel(atdma, name, val) \
+	__raw_writel((val), (atdma)->regs + AT_DMA_##name)
+
+static inline struct at_dma *to_at_dma(struct dma_device *ddev)
+{
+	return container_of(ddev, struct at_dma, dma_common);
+}
+
+
+/*--  Helper functions  ------------------------------------------------*/
+
+static struct device *chan2dev(struct dma_chan *chan)
+{
+	return &chan->dev->device;
+}
+static struct device *chan2parent(struct dma_chan *chan)
+{
+	return chan->dev->device.parent;
+}
+
+#if defined(VERBOSE_DEBUG)
+static void vdbg_dump_regs(struct at_dma_chan *atchan)
+{
+	struct at_dma	*atdma = to_at_dma(atchan->chan_common.device);
+
+	dev_err(chan2dev(&atchan->chan_common),
+		"  channel %d : imr = 0x%x, chsr = 0x%x\n",
+		atchan->chan_common.chan_id,
+		dma_readl(atdma, EBCIMR),
+		dma_readl(atdma, CHSR));
+
+	dev_err(chan2dev(&atchan->chan_common),
+		"  channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n",
+		channel_readl(atchan, SADDR),
+		channel_readl(atchan, DADDR),
+		channel_readl(atchan, CTRLA),
+		channel_readl(atchan, CTRLB),
+		channel_readl(atchan, DSCR));
+}
+#else
+static void vdbg_dump_regs(struct at_dma_chan *atchan) {}
+#endif
+
+static void atc_dump_lli(struct at_dma_chan *atchan, struct at_lli *lli)
+{
+	dev_printk(KERN_CRIT, chan2dev(&atchan->chan_common),
+			"  desc: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n",
+			lli->saddr, lli->daddr,
+			lli->ctrla, lli->ctrlb, lli->dscr);
+}
+
+
+static void atc_setup_irq(struct at_dma_chan *atchan, int on)
+{
+	struct at_dma	*atdma = to_at_dma(atchan->chan_common.device);
+	u32		ebci;
+
+	/* enable interrupts on buffer chain completion & error */
+	ebci =    AT_DMA_CBTC(atchan->chan_common.chan_id)
+		| AT_DMA_ERR(atchan->chan_common.chan_id);
+	if (on)
+		dma_writel(atdma, EBCIER, ebci);
+	else
+		dma_writel(atdma, EBCIDR, ebci);
+}
+
+static inline void atc_enable_irq(struct at_dma_chan *atchan)
+{
+	atc_setup_irq(atchan, 1);
+}
+
+static inline void atc_disable_irq(struct at_dma_chan *atchan)
+{
+	atc_setup_irq(atchan, 0);
+}
+
+
+/**
+ * atc_chan_is_enabled - test if given channel is enabled
+ * @atchan: channel we want to test status
+ */
+static inline int atc_chan_is_enabled(struct at_dma_chan *atchan)
+{
+	struct at_dma	*atdma = to_at_dma(atchan->chan_common.device);
+
+	return !!(dma_readl(atdma, CHSR) & atchan->mask);
+}
+
+
+/**
+ * set_desc_eol - set end-of-link to descriptor so it will end transfer
+ * @desc: descriptor, signle or at the end of a chain, to end chain on
+ */
+static void set_desc_eol(struct at_desc *desc)
+{
+	desc->lli.ctrlb |= ATC_SRC_DSCR_DIS | ATC_DST_DSCR_DIS;
+	desc->lli.dscr = 0;
+}
+
+#endif /* AT_HDMAC_REGS_H */
-- 
GitLab


From 808347f6a31792079e345ec865e9cfcb6e8ae6b2 Mon Sep 17 00:00:00 2001
From: Nicolas Ferre <nicolas.ferre@atmel.com>
Date: Wed, 22 Jul 2009 20:04:45 +0200
Subject: [PATCH 0066/1153] dmaengine: at_hdmac: add DMA slave transfers

This patch for at_hdmac adds the slave transfers capability to the Atmel DMA
controller available on some AT91 SOCs. This allow peripheral to memory and
memory to peripheral transfers with hardware handshaking.

Slave structure for controller specific information is passed through channel
private data. This at_dma_slave structure is defined in at_hdmac.h header file
and relative hardware definition are moved to this file from at_hdmac_regs.h.
Doing this we allow the channel configuration from platform definition code.

This work is intensively based on dw_dmac and several slave implementations.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
---
 arch/arm/mach-at91/include/mach/at_hdmac.h |  76 ++++++++
 drivers/dma/at_hdmac.c                     | 208 ++++++++++++++++++++-
 drivers/dma/at_hdmac_regs.h                |  49 +----
 3 files changed, 290 insertions(+), 43 deletions(-)

diff --git a/arch/arm/mach-at91/include/mach/at_hdmac.h b/arch/arm/mach-at91/include/mach/at_hdmac.h
index 21a5554f9cb..187cb58345c 100644
--- a/arch/arm/mach-at91/include/mach/at_hdmac.h
+++ b/arch/arm/mach-at91/include/mach/at_hdmac.h
@@ -23,4 +23,80 @@ struct at_dma_platform_data {
 	dma_cap_mask_t  cap_mask;
 };
 
+/**
+ * enum at_dma_slave_width - DMA slave register access width.
+ * @AT_DMA_SLAVE_WIDTH_8BIT: Do 8-bit slave register accesses
+ * @AT_DMA_SLAVE_WIDTH_16BIT: Do 16-bit slave register accesses
+ * @AT_DMA_SLAVE_WIDTH_32BIT: Do 32-bit slave register accesses
+ */
+enum at_dma_slave_width {
+	AT_DMA_SLAVE_WIDTH_8BIT = 0,
+	AT_DMA_SLAVE_WIDTH_16BIT,
+	AT_DMA_SLAVE_WIDTH_32BIT,
+};
+
+/**
+ * struct at_dma_slave - Controller-specific information about a slave
+ * @dma_dev: required DMA master device
+ * @tx_reg: physical address of data register used for
+ *	memory-to-peripheral transfers
+ * @rx_reg: physical address of data register used for
+ *	peripheral-to-memory transfers
+ * @reg_width: peripheral register width
+ * @cfg: Platform-specific initializer for the CFG register
+ * @ctrla: Platform-specific initializer for the CTRLA register
+ */
+struct at_dma_slave {
+	struct device		*dma_dev;
+	dma_addr_t		tx_reg;
+	dma_addr_t		rx_reg;
+	enum at_dma_slave_width	reg_width;
+	u32			cfg;
+	u32			ctrla;
+};
+
+
+/* Platform-configurable bits in CFG */
+#define	ATC_SRC_PER(h)		(0xFU & (h))	/* Channel src rq associated with periph handshaking ifc h */
+#define	ATC_DST_PER(h)		((0xFU & (h)) <<  4)	/* Channel dst rq associated with periph handshaking ifc h */
+#define	ATC_SRC_REP		(0x1 <<  8)	/* Source Replay Mod */
+#define	ATC_SRC_H2SEL		(0x1 <<  9)	/* Source Handshaking Mod */
+#define		ATC_SRC_H2SEL_SW	(0x0 <<  9)
+#define		ATC_SRC_H2SEL_HW	(0x1 <<  9)
+#define	ATC_DST_REP		(0x1 << 12)	/* Destination Replay Mod */
+#define	ATC_DST_H2SEL		(0x1 << 13)	/* Destination Handshaking Mod */
+#define		ATC_DST_H2SEL_SW	(0x0 << 13)
+#define		ATC_DST_H2SEL_HW	(0x1 << 13)
+#define	ATC_SOD			(0x1 << 16)	/* Stop On Done */
+#define	ATC_LOCK_IF		(0x1 << 20)	/* Interface Lock */
+#define	ATC_LOCK_B		(0x1 << 21)	/* AHB Bus Lock */
+#define	ATC_LOCK_IF_L		(0x1 << 22)	/* Master Interface Arbiter Lock */
+#define		ATC_LOCK_IF_L_CHUNK	(0x0 << 22)
+#define		ATC_LOCK_IF_L_BUFFER	(0x1 << 22)
+#define	ATC_AHB_PROT_MASK	(0x7 << 24)	/* AHB Protection */
+#define	ATC_FIFOCFG_MASK	(0x3 << 28)	/* FIFO Request Configuration */
+#define		ATC_FIFOCFG_LARGESTBURST	(0x0 << 28)
+#define		ATC_FIFOCFG_HALFFIFO		(0x1 << 28)
+#define		ATC_FIFOCFG_ENOUGHSPACE		(0x2 << 28)
+
+/* Platform-configurable bits in CTRLA */
+#define	ATC_SCSIZE_MASK		(0x7 << 16)	/* Source Chunk Transfer Size */
+#define		ATC_SCSIZE_1		(0x0 << 16)
+#define		ATC_SCSIZE_4		(0x1 << 16)
+#define		ATC_SCSIZE_8		(0x2 << 16)
+#define		ATC_SCSIZE_16		(0x3 << 16)
+#define		ATC_SCSIZE_32		(0x4 << 16)
+#define		ATC_SCSIZE_64		(0x5 << 16)
+#define		ATC_SCSIZE_128		(0x6 << 16)
+#define		ATC_SCSIZE_256		(0x7 << 16)
+#define	ATC_DCSIZE_MASK		(0x7 << 20)	/* Destination Chunk Transfer Size */
+#define		ATC_DCSIZE_1		(0x0 << 20)
+#define		ATC_DCSIZE_4		(0x1 << 20)
+#define		ATC_DCSIZE_8		(0x2 << 20)
+#define		ATC_DCSIZE_16		(0x3 << 20)
+#define		ATC_DCSIZE_32		(0x4 << 20)
+#define		ATC_DCSIZE_64		(0x5 << 20)
+#define		ATC_DCSIZE_128		(0x6 << 20)
+#define		ATC_DCSIZE_256		(0x7 << 20)
+
 #endif /* AT_HDMAC_H */
diff --git a/drivers/dma/at_hdmac.c b/drivers/dma/at_hdmac.c
index 64dbf0ce128..9a1e5fb412e 100644
--- a/drivers/dma/at_hdmac.c
+++ b/drivers/dma/at_hdmac.c
@@ -608,6 +608,187 @@ err_desc_get:
 	return NULL;
 }
 
+
+/**
+ * atc_prep_slave_sg - prepare descriptors for a DMA_SLAVE transaction
+ * @chan: DMA channel
+ * @sgl: scatterlist to transfer to/from
+ * @sg_len: number of entries in @scatterlist
+ * @direction: DMA direction
+ * @flags: tx descriptor status flags
+ */
+static struct dma_async_tx_descriptor *
+atc_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl,
+		unsigned int sg_len, enum dma_data_direction direction,
+		unsigned long flags)
+{
+	struct at_dma_chan	*atchan = to_at_dma_chan(chan);
+	struct at_dma_slave	*atslave = chan->private;
+	struct at_desc		*first = NULL;
+	struct at_desc		*prev = NULL;
+	u32			ctrla;
+	u32			ctrlb;
+	dma_addr_t		reg;
+	unsigned int		reg_width;
+	unsigned int		mem_width;
+	unsigned int		i;
+	struct scatterlist	*sg;
+	size_t			total_len = 0;
+
+	dev_vdbg(chan2dev(chan), "prep_slave_sg: %s f0x%lx\n",
+			direction == DMA_TO_DEVICE ? "TO DEVICE" : "FROM DEVICE",
+			flags);
+
+	if (unlikely(!atslave || !sg_len)) {
+		dev_dbg(chan2dev(chan), "prep_dma_memcpy: length is zero!\n");
+		return NULL;
+	}
+
+	reg_width = atslave->reg_width;
+
+	sg_len = dma_map_sg(chan2parent(chan), sgl, sg_len, direction);
+
+	ctrla = ATC_DEFAULT_CTRLA | atslave->ctrla;
+	ctrlb = ATC_DEFAULT_CTRLB | ATC_IEN;
+
+	switch (direction) {
+	case DMA_TO_DEVICE:
+		ctrla |=  ATC_DST_WIDTH(reg_width);
+		ctrlb |=  ATC_DST_ADDR_MODE_FIXED
+			| ATC_SRC_ADDR_MODE_INCR
+			| ATC_FC_MEM2PER;
+		reg = atslave->tx_reg;
+		for_each_sg(sgl, sg, sg_len, i) {
+			struct at_desc	*desc;
+			u32		len;
+			u32		mem;
+
+			desc = atc_desc_get(atchan);
+			if (!desc)
+				goto err_desc_get;
+
+			mem = sg_phys(sg);
+			len = sg_dma_len(sg);
+			mem_width = 2;
+			if (unlikely(mem & 3 || len & 3))
+				mem_width = 0;
+
+			desc->lli.saddr = mem;
+			desc->lli.daddr = reg;
+			desc->lli.ctrla = ctrla
+					| ATC_SRC_WIDTH(mem_width)
+					| len >> mem_width;
+			desc->lli.ctrlb = ctrlb;
+
+			if (!first) {
+				first = desc;
+			} else {
+				/* inform the HW lli about chaining */
+				prev->lli.dscr = desc->txd.phys;
+				/* insert the link descriptor to the LD ring */
+				list_add_tail(&desc->desc_node,
+						&first->txd.tx_list);
+			}
+			prev = desc;
+			total_len += len;
+		}
+		break;
+	case DMA_FROM_DEVICE:
+		ctrla |=  ATC_SRC_WIDTH(reg_width);
+		ctrlb |=  ATC_DST_ADDR_MODE_INCR
+			| ATC_SRC_ADDR_MODE_FIXED
+			| ATC_FC_PER2MEM;
+
+		reg = atslave->rx_reg;
+		for_each_sg(sgl, sg, sg_len, i) {
+			struct at_desc	*desc;
+			u32		len;
+			u32		mem;
+
+			desc = atc_desc_get(atchan);
+			if (!desc)
+				goto err_desc_get;
+
+			mem = sg_phys(sg);
+			len = sg_dma_len(sg);
+			mem_width = 2;
+			if (unlikely(mem & 3 || len & 3))
+				mem_width = 0;
+
+			desc->lli.saddr = reg;
+			desc->lli.daddr = mem;
+			desc->lli.ctrla = ctrla
+					| ATC_DST_WIDTH(mem_width)
+					| len >> mem_width;
+			desc->lli.ctrlb = ctrlb;
+
+			if (!first) {
+				first = desc;
+			} else {
+				/* inform the HW lli about chaining */
+				prev->lli.dscr = desc->txd.phys;
+				/* insert the link descriptor to the LD ring */
+				list_add_tail(&desc->desc_node,
+						&first->txd.tx_list);
+			}
+			prev = desc;
+			total_len += len;
+		}
+		break;
+	default:
+		return NULL;
+	}
+
+	/* set end-of-link to the last link descriptor of list*/
+	set_desc_eol(prev);
+
+	/* First descriptor of the chain embedds additional information */
+	first->txd.cookie = -EBUSY;
+	first->len = total_len;
+
+	/* last link descriptor of list is responsible of flags */
+	prev->txd.flags = flags; /* client is in control of this ack */
+
+	return &first->txd;
+
+err_desc_get:
+	dev_err(chan2dev(chan), "not enough descriptors available\n");
+	atc_desc_put(atchan, first);
+	return NULL;
+}
+
+static void atc_terminate_all(struct dma_chan *chan)
+{
+	struct at_dma_chan	*atchan = to_at_dma_chan(chan);
+	struct at_dma		*atdma = to_at_dma(chan->device);
+	struct at_desc		*desc, *_desc;
+	LIST_HEAD(list);
+
+	/*
+	 * This is only called when something went wrong elsewhere, so
+	 * we don't really care about the data. Just disable the
+	 * channel. We still have to poll the channel enable bit due
+	 * to AHB/HSB limitations.
+	 */
+	spin_lock_bh(&atchan->lock);
+
+	dma_writel(atdma, CHDR, atchan->mask);
+
+	/* confirm that this channel is disabled */
+	while (dma_readl(atdma, CHSR) & atchan->mask)
+		cpu_relax();
+
+	/* active_list entries will end up before queued entries */
+	list_splice_init(&atchan->queue, &list);
+	list_splice_init(&atchan->active_list, &list);
+
+	spin_unlock_bh(&atchan->lock);
+
+	/* Flush all pending and queued descriptors */
+	list_for_each_entry_safe(desc, _desc, &list, desc_node)
+		atc_chain_complete(atchan, desc);
+}
+
 /**
  * atc_is_tx_complete - poll for transaction completion
  * @chan: DMA channel
@@ -686,7 +867,9 @@ static int atc_alloc_chan_resources(struct dma_chan *chan)
 	struct at_dma_chan	*atchan = to_at_dma_chan(chan);
 	struct at_dma		*atdma = to_at_dma(chan->device);
 	struct at_desc		*desc;
+	struct at_dma_slave	*atslave;
 	int			i;
+	u32			cfg;
 	LIST_HEAD(tmp_list);
 
 	dev_vdbg(chan2dev(chan), "alloc_chan_resources\n");
@@ -697,7 +880,23 @@ static int atc_alloc_chan_resources(struct dma_chan *chan)
 		return -EIO;
 	}
 
-	/* have we already been set up? */
+	cfg = ATC_DEFAULT_CFG;
+
+	atslave = chan->private;
+	if (atslave) {
+		/*
+		 * We need controller-specific data to set up slave
+		 * transfers.
+		 */
+		BUG_ON(!atslave->dma_dev || atslave->dma_dev != atdma->dma_common.dev);
+
+		/* if cfg configuration specified take it instad of default */
+		if (atslave->cfg)
+			cfg = atslave->cfg;
+	}
+
+	/* have we already been set up?
+	 * reconfigure channel but no need to reallocate descriptors */
 	if (!list_empty(&atchan->free_list))
 		return atchan->descs_allocated;
 
@@ -719,7 +918,7 @@ static int atc_alloc_chan_resources(struct dma_chan *chan)
 	spin_unlock_bh(&atchan->lock);
 
 	/* channel parameters */
-	channel_writel(atchan, CFG, ATC_DEFAULT_CFG);
+	channel_writel(atchan, CFG, cfg);
 
 	dev_dbg(chan2dev(chan),
 		"alloc_chan_resources: allocated %d descriptors\n",
@@ -888,6 +1087,11 @@ static int __init at_dma_probe(struct platform_device *pdev)
 	if (dma_has_cap(DMA_MEMCPY, atdma->dma_common.cap_mask))
 		atdma->dma_common.device_prep_dma_memcpy = atc_prep_dma_memcpy;
 
+	if (dma_has_cap(DMA_SLAVE, atdma->dma_common.cap_mask)) {
+		atdma->dma_common.device_prep_slave_sg = atc_prep_slave_sg;
+		atdma->dma_common.device_terminate_all = atc_terminate_all;
+	}
+
 	dma_writel(atdma, EN, AT_DMA_ENABLE);
 
 	dev_info(&pdev->dev, "Atmel AHB DMA Controller ( %s%s), %d channels\n",
diff --git a/drivers/dma/at_hdmac_regs.h b/drivers/dma/at_hdmac_regs.h
index ad2d4f402bf..4c972afc49e 100644
--- a/drivers/dma/at_hdmac_regs.h
+++ b/drivers/dma/at_hdmac_regs.h
@@ -87,29 +87,14 @@
 /* Bitfields in CTRLA */
 #define	ATC_BTSIZE_MAX		0xFFFFUL	/* Maximum Buffer Transfer Size */
 #define	ATC_BTSIZE(x)		(ATC_BTSIZE_MAX & (x)) /* Buffer Transfer Size */
-#define	ATC_SCSIZE_MASK		(0x7 << 16)	/* Source Chunk Transfer Size */
-#define		ATC_SCSIZE_1		(0x0 << 16)
-#define		ATC_SCSIZE_4		(0x1 << 16)
-#define		ATC_SCSIZE_8		(0x2 << 16)
-#define		ATC_SCSIZE_16		(0x3 << 16)
-#define		ATC_SCSIZE_32		(0x4 << 16)
-#define		ATC_SCSIZE_64		(0x5 << 16)
-#define		ATC_SCSIZE_128		(0x6 << 16)
-#define		ATC_SCSIZE_256		(0x7 << 16)
-#define	ATC_DCSIZE_MASK		(0x7 << 20)	/* Destination Chunk Transfer Size */
-#define		ATC_DCSIZE_1		(0x0 << 20)
-#define		ATC_DCSIZE_4		(0x1 << 20)
-#define		ATC_DCSIZE_8		(0x2 << 20)
-#define		ATC_DCSIZE_16		(0x3 << 20)
-#define		ATC_DCSIZE_32		(0x4 << 20)
-#define		ATC_DCSIZE_64		(0x5 << 20)
-#define		ATC_DCSIZE_128		(0x6 << 20)
-#define		ATC_DCSIZE_256		(0x7 << 20)
+/* Chunck Tranfer size definitions are in at_hdmac.h */
 #define	ATC_SRC_WIDTH_MASK	(0x3 << 24)	/* Source Single Transfer Size */
+#define		ATC_SRC_WIDTH(x)	((x) << 24)
 #define		ATC_SRC_WIDTH_BYTE	(0x0 << 24)
 #define		ATC_SRC_WIDTH_HALFWORD	(0x1 << 24)
 #define		ATC_SRC_WIDTH_WORD	(0x2 << 24)
 #define	ATC_DST_WIDTH_MASK	(0x3 << 28)	/* Destination Single Transfer Size */
+#define		ATC_DST_WIDTH(x)	((x) << 28)
 #define		ATC_DST_WIDTH_BYTE	(0x0 << 28)
 #define		ATC_DST_WIDTH_HALFWORD	(0x1 << 28)
 #define		ATC_DST_WIDTH_WORD	(0x2 << 28)
@@ -129,7 +114,8 @@
 #define		ATC_FC_PER2PER		(0x3 << 21)	/* Periph-to-Periph (DMA) */
 #define		ATC_FC_PER2MEM_PER	(0x4 << 21)	/* Periph-to-Mem (Peripheral) */
 #define		ATC_FC_MEM2PER_PER	(0x5 << 21)	/* Mem-to-Periph (Peripheral) */
-#define		ATC_FC_PER2PER_PER	(0x6 << 21)	/* Periph-to-Periph (Src Peripheral) */
+#define		ATC_FC_PER2PER_SRCPER	(0x6 << 21)	/* Periph-to-Periph (Src Peripheral) */
+#define		ATC_FC_PER2PER_DSTPER	(0x7 << 21)	/* Periph-to-Periph (Dst Peripheral) */
 #define	ATC_SRC_ADDR_MODE_MASK	(0x3 << 24)
 #define		ATC_SRC_ADDR_MODE_INCR	(0x0 << 24)	/* Incrementing Mode */
 #define		ATC_SRC_ADDR_MODE_DECR	(0x1 << 24)	/* Decrementing Mode */
@@ -142,27 +128,7 @@
 #define	ATC_AUTO		(0x1 << 31)	/* Auto multiple buffer tx enable */
 
 /* Bitfields in CFG */
-#define	ATC_SRC_PER(h)		(0xFU & (h))	/* Channel src rq associated with periph handshaking ifc h */
-#define	ATC_DST_PER(h)		((0xFU & (h)) <<  4)	/* Channel dst rq associated with periph handshaking ifc h */
-#define	ATC_SRC_REP		(0x1 <<  8)	/* Source Replay Mod */
-#define	ATC_SRC_H2SEL		(0x1 <<  9)	/* Source Handshaking Mod */
-#define		ATC_SRC_H2SEL_SW	(0x0 <<  9)
-#define		ATC_SRC_H2SEL_HW	(0x1 <<  9)
-#define	ATC_DST_REP		(0x1 << 12)	/* Destination Replay Mod */
-#define	ATC_DST_H2SEL		(0x1 << 13)	/* Destination Handshaking Mod */
-#define		ATC_DST_H2SEL_SW	(0x0 << 13)
-#define		ATC_DST_H2SEL_HW	(0x1 << 13)
-#define	ATC_SOD			(0x1 << 16)	/* Stop On Done */
-#define	ATC_LOCK_IF		(0x1 << 20)	/* Interface Lock */
-#define	ATC_LOCK_B		(0x1 << 21)	/* AHB Bus Lock */
-#define	ATC_LOCK_IF_L		(0x1 << 22)	/* Master Interface Arbiter Lock */
-#define		ATC_LOCK_IF_L_CHUNK	(0x0 << 22)
-#define		ATC_LOCK_IF_L_BUFFER	(0x1 << 22)
-#define	ATC_AHB_PROT_MASK	(0x7 << 24)	/* AHB Protection */
-#define	ATC_FIFOCFG_MASK	(0x3 << 28)	/* FIFO Request Configuration */
-#define		ATC_FIFOCFG_LARGESTBURST	(0x0 << 28)
-#define		ATC_FIFOCFG_HALFFIFO		(0x1 << 28)
-#define		ATC_FIFOCFG_ENOUGHSPACE		(0x2 << 28)
+/* are in at_hdmac.h */
 
 /* Bitfields in SPIP */
 #define	ATC_SPIP_HOLE(x)	(0xFFFFU & (x))
@@ -316,11 +282,12 @@ static void vdbg_dump_regs(struct at_dma_chan *atchan)
 		dma_readl(atdma, CHSR));
 
 	dev_err(chan2dev(&atchan->chan_common),
-		"  channel: s0x%x d0x%x ctrl0x%x:0x%x l0x%x\n",
+		"  channel: s0x%x d0x%x ctrl0x%x:0x%x cfg0x%x l0x%x\n",
 		channel_readl(atchan, SADDR),
 		channel_readl(atchan, DADDR),
 		channel_readl(atchan, CTRLA),
 		channel_readl(atchan, CTRLB),
+		channel_readl(atchan, CFG),
 		channel_readl(atchan, DSCR));
 }
 #else
-- 
GitLab


From 3174c88af4b6b2e81cacfaa2bb90cc7abe36f1cc Mon Sep 17 00:00:00 2001
From: Hartley Sweeten <hartleys@visionengravers.com>
Date: Mon, 20 Jul 2009 18:12:23 +0100
Subject: [PATCH 0067/1153] [ARM] 5611/1: ep93xx: update ts72xx nor flash
 support

Update the NOR flash support for TS-7200.

The TS-7200 models all have 16-bit NOR flash.  Update the platform
init to support this.

Remove the private TS72XX_NOR_* defines and use the common ep93xx
defines for the external chip select physical base address instead.

Move the NOR flash registration into a static __init function.  When
the NAND flash support is updated this function will also be used
to register the NAND flash for the TS-7250 and TS-7260.

Tested-by: Matthieu Crapet <mcrapet@gmail.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-ep93xx/include/mach/ts72xx.h |  3 ---
 arch/arm/mach-ep93xx/ts72xx.c              | 18 +++++++++++++-----
 2 files changed, 13 insertions(+), 8 deletions(-)

diff --git a/arch/arm/mach-ep93xx/include/mach/ts72xx.h b/arch/arm/mach-ep93xx/include/mach/ts72xx.h
index 34ddec081c4..411734422c1 100644
--- a/arch/arm/mach-ep93xx/include/mach/ts72xx.h
+++ b/arch/arm/mach-ep93xx/include/mach/ts72xx.h
@@ -41,9 +41,6 @@
 #define TS72XX_OPTIONS2_TS9420_BOOT	0x02
 
 
-#define TS72XX_NOR_PHYS_BASE		0x60000000
-#define TS72XX_NOR2_PHYS_BASE		0x62000000
-
 #define TS72XX_NAND1_DATA_PHYS_BASE	0x60000000
 #define TS72XX_NAND2_DATA_PHYS_BASE	0x70000000
 #define TS72XX_NAND_DATA_VIRT_BASE	0xfebfc000
diff --git a/arch/arm/mach-ep93xx/ts72xx.c b/arch/arm/mach-ep93xx/ts72xx.c
index 7ee024d3482..aaf1371412a 100644
--- a/arch/arm/mach-ep93xx/ts72xx.c
+++ b/arch/arm/mach-ep93xx/ts72xx.c
@@ -112,13 +112,16 @@ static void __init ts72xx_map_io(void)
 	}
 }
 
+/*************************************************************************
+ * NOR flash (TS-7200 only)
+ *************************************************************************/
 static struct physmap_flash_data ts72xx_flash_data = {
-	.width		= 1,
+	.width		= 2,
 };
 
 static struct resource ts72xx_flash_resource = {
-	.start		= TS72XX_NOR_PHYS_BASE,
-	.end		= TS72XX_NOR_PHYS_BASE + SZ_16M - 1,
+	.start		= EP93XX_CS6_PHYS_BASE,
+	.end		= EP93XX_CS6_PHYS_BASE + SZ_16M - 1,
 	.flags		= IORESOURCE_MEM,
 };
 
@@ -132,6 +135,12 @@ static struct platform_device ts72xx_flash = {
 	.resource	= &ts72xx_flash_resource,
 };
 
+static void __init ts72xx_register_flash(void)
+{
+	if (board_is_ts7200())
+		platform_device_register(&ts72xx_flash);
+}
+
 static unsigned char ts72xx_rtc_readbyte(unsigned long addr)
 {
 	__raw_writeb(addr, TS72XX_RTC_INDEX_VIRT_BASE);
@@ -165,8 +174,7 @@ static struct ep93xx_eth_data ts72xx_eth_data = {
 static void __init ts72xx_init_machine(void)
 {
 	ep93xx_init_devices();
-	if (board_is_ts7200())
-		platform_device_register(&ts72xx_flash);
+	ts72xx_register_flash();
 	platform_device_register(&ts72xx_rtc_device);
 
 	ep93xx_register_eth(&ts72xx_eth_data, 1);
-- 
GitLab


From d8cc1ab793993c886c62abf77c93287df33ffd8b Mon Sep 17 00:00:00 2001
From: Li Zefan <lizf@cn.fujitsu.com>
Date: Thu, 23 Jul 2009 11:28:40 +0800
Subject: [PATCH 0068/1153] trace_stack: Fix seqfile memory leak

Every time we cat stack_trace, we leak memory allocated by seq_open().

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4A67D8E8.3020500@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 kernel/trace/trace_stack.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)

diff --git a/kernel/trace/trace_stack.c b/kernel/trace/trace_stack.c
index e644af91012..6a2a9d484cd 100644
--- a/kernel/trace/trace_stack.c
+++ b/kernel/trace/trace_stack.c
@@ -301,17 +301,14 @@ static const struct seq_operations stack_trace_seq_ops = {
 
 static int stack_trace_open(struct inode *inode, struct file *file)
 {
-	int ret;
-
-	ret = seq_open(file, &stack_trace_seq_ops);
-
-	return ret;
+	return seq_open(file, &stack_trace_seq_ops);
 }
 
 static const struct file_operations stack_trace_fops = {
 	.open		= stack_trace_open,
 	.read		= seq_read,
 	.llseek		= seq_lseek,
+	.release	= seq_release,
 };
 
 int
-- 
GitLab


From 87827111a5538633b18e5c641ced673c4c2bb6ce Mon Sep 17 00:00:00 2001
From: Li Zefan <lizf@cn.fujitsu.com>
Date: Thu, 23 Jul 2009 11:29:11 +0800
Subject: [PATCH 0069/1153] function-graph: Fix seqfile memory leak

Every time we cat set_graph_function, we leak memory allocated
by seq_open().

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4A67D907.2010500@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 kernel/trace/ftrace.c | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/kernel/trace/ftrace.c b/kernel/trace/ftrace.c
index 4521c77d1a1..1f3ec2afa51 100644
--- a/kernel/trace/ftrace.c
+++ b/kernel/trace/ftrace.c
@@ -2595,6 +2595,14 @@ ftrace_graph_open(struct inode *inode, struct file *file)
 	return ret;
 }
 
+static int
+ftrace_graph_release(struct inode *inode, struct file *file)
+{
+	if (file->f_mode & FMODE_READ)
+		seq_release(inode, file);
+	return 0;
+}
+
 static int
 ftrace_set_func(unsigned long *array, int *idx, char *buffer)
 {
@@ -2724,9 +2732,10 @@ ftrace_graph_write(struct file *file, const char __user *ubuf,
 }
 
 static const struct file_operations ftrace_graph_fops = {
-	.open = ftrace_graph_open,
-	.read = seq_read,
-	.write = ftrace_graph_write,
+	.open		= ftrace_graph_open,
+	.read		= seq_read,
+	.write		= ftrace_graph_write,
+	.release	= ftrace_graph_release,
 };
 #endif /* CONFIG_FUNCTION_GRAPH_TRACER */
 
-- 
GitLab


From 636eacee3b0c76915151db37203cc624becb6d7b Mon Sep 17 00:00:00 2001
From: Li Zefan <lizf@cn.fujitsu.com>
Date: Thu, 23 Jul 2009 11:29:47 +0800
Subject: [PATCH 0070/1153] tracing/stat: Fix seqfile memory leak

Every time we cat a trace_stat file, we leak memory allocated by
seq_open().

Also fix memory leak in a failure path in tracing_stat_open().

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4A67D92B.4060704@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 kernel/trace/trace_stat.c | 34 ++++++++++++++++++++++------------
 1 file changed, 22 insertions(+), 12 deletions(-)

diff --git a/kernel/trace/trace_stat.c b/kernel/trace/trace_stat.c
index e66f5e49334..aea321c82fa 100644
--- a/kernel/trace/trace_stat.c
+++ b/kernel/trace/trace_stat.c
@@ -73,7 +73,7 @@ static struct rb_node *release_next(struct rb_node *node)
 	}
 }
 
-static void reset_stat_session(struct stat_session *session)
+static void __reset_stat_session(struct stat_session *session)
 {
 	struct rb_node *node = session->stat_root.rb_node;
 
@@ -83,10 +83,17 @@ static void reset_stat_session(struct stat_session *session)
 	session->stat_root = RB_ROOT;
 }
 
+static void reset_stat_session(struct stat_session *session)
+{
+	mutex_lock(&session->stat_mutex);
+	__reset_stat_session(session);
+	mutex_unlock(&session->stat_mutex);
+}
+
 static void destroy_session(struct stat_session *session)
 {
 	debugfs_remove(session->file);
-	reset_stat_session(session);
+	__reset_stat_session(session);
 	mutex_destroy(&session->stat_mutex);
 	kfree(session);
 }
@@ -150,7 +157,7 @@ static int stat_seq_init(struct stat_session *session)
 	int i;
 
 	mutex_lock(&session->stat_mutex);
-	reset_stat_session(session);
+	__reset_stat_session(session);
 
 	if (!ts->stat_cmp)
 		ts->stat_cmp = dummy_cmp;
@@ -183,7 +190,7 @@ exit:
 	return ret;
 
 exit_free_rbtree:
-	reset_stat_session(session);
+	__reset_stat_session(session);
 	mutex_unlock(&session->stat_mutex);
 	return ret;
 }
@@ -250,16 +257,21 @@ static const struct seq_operations trace_stat_seq_ops = {
 static int tracing_stat_open(struct inode *inode, struct file *file)
 {
 	int ret;
-
+	struct seq_file *m;
 	struct stat_session *session = inode->i_private;
 
+	ret = stat_seq_init(session);
+	if (ret)
+		return ret;
+
 	ret = seq_open(file, &trace_stat_seq_ops);
-	if (!ret) {
-		struct seq_file *m = file->private_data;
-		m->private = session;
-		ret = stat_seq_init(session);
+	if (ret) {
+		reset_stat_session(session);
+		return ret;
 	}
 
+	m = file->private_data;
+	m->private = session;
 	return ret;
 }
 
@@ -270,11 +282,9 @@ static int tracing_stat_release(struct inode *i, struct file *f)
 {
 	struct stat_session *session = i->i_private;
 
-	mutex_lock(&session->stat_mutex);
 	reset_stat_session(session);
-	mutex_unlock(&session->stat_mutex);
 
-	return 0;
+	return seq_release(i, f);
 }
 
 static const struct file_operations tracing_stat_fops = {
-- 
GitLab


From 4c739ff043e5787d97c9691d62cabf7a29e75a9d Mon Sep 17 00:00:00 2001
From: Steven Rostedt <srostedt@redhat.com>
Date: Wed, 22 Jul 2009 23:11:03 -0400
Subject: [PATCH 0071/1153] tracing: show proper address for trace-printk
 format

Since the trace_printk may use pointers to the format fields
in the buffer, they are exported via debugfs/tracing/printk_formats.
This is used by utilities that read the ring buffer in binary format.
It helps the utilities map the address of the format in the binary
buffer to what the printf format looks like.

Unfortunately, the way the output code works, it exports the address
of the pointer to the format address, and not the format address
itself. This makes the file totally useless in trying to figure
out what format string a binary address belongs to.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 kernel/trace/trace_printk.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/trace/trace_printk.c b/kernel/trace/trace_printk.c
index 7b627811082..687699d365a 100644
--- a/kernel/trace/trace_printk.c
+++ b/kernel/trace/trace_printk.c
@@ -176,7 +176,7 @@ static int t_show(struct seq_file *m, void *v)
 	const char *str = *fmt;
 	int i;
 
-	seq_printf(m, "0x%lx : \"", (unsigned long)fmt);
+	seq_printf(m, "0x%lx : \"", *(unsigned long *)fmt);
 
 	/*
 	 * Tabs and new lines need to be converted.
-- 
GitLab


From 8650ae32ef7045e763825dee6256dde7f331bb85 Mon Sep 17 00:00:00 2001
From: Steven Rostedt <srostedt@redhat.com>
Date: Wed, 22 Jul 2009 23:29:30 -0400
Subject: [PATCH 0072/1153] tracing: only truncate ftrace files when O_TRUNC is
 set

The current code will truncate the ftrace files contents if O_APPEND
is not set and the file is opened in write mode. This is incorrect.
It should only truncate the file if O_TRUNC is set. Otherwise
if one of these files is opened by a C program with fopen "r+",
it will incorrectly truncate the file.

Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 kernel/trace/ftrace.c       | 4 ++--
 kernel/trace/trace.c        | 2 +-
 kernel/trace/trace_events.c | 2 +-
 3 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/kernel/trace/ftrace.c b/kernel/trace/ftrace.c
index 1f3ec2afa51..1e1d23c2630 100644
--- a/kernel/trace/ftrace.c
+++ b/kernel/trace/ftrace.c
@@ -1662,7 +1662,7 @@ ftrace_regex_open(struct inode *inode, struct file *file, int enable)
 
 	mutex_lock(&ftrace_regex_lock);
 	if ((file->f_mode & FMODE_WRITE) &&
-	    !(file->f_flags & O_APPEND))
+	    (file->f_flags & O_TRUNC))
 		ftrace_filter_reset(enable);
 
 	if (file->f_mode & FMODE_READ) {
@@ -2577,7 +2577,7 @@ ftrace_graph_open(struct inode *inode, struct file *file)
 
 	mutex_lock(&graph_lock);
 	if ((file->f_mode & FMODE_WRITE) &&
-	    !(file->f_flags & O_APPEND)) {
+	    (file->f_flags & O_TRUNC)) {
 		ftrace_graph_count = 0;
 		memset(ftrace_graph_funcs, 0, sizeof(ftrace_graph_funcs));
 	}
diff --git a/kernel/trace/trace.c b/kernel/trace/trace.c
index 8bc8d8afea6..d8ef28574aa 100644
--- a/kernel/trace/trace.c
+++ b/kernel/trace/trace.c
@@ -2031,7 +2031,7 @@ static int tracing_open(struct inode *inode, struct file *file)
 
 	/* If this file was open for write, then erase contents */
 	if ((file->f_mode & FMODE_WRITE) &&
-	    !(file->f_flags & O_APPEND)) {
+	    (file->f_flags & O_TRUNC)) {
 		long cpu = (long) inode->i_private;
 
 		if (cpu == TRACE_PIPE_ALL_CPU)
diff --git a/kernel/trace/trace_events.c b/kernel/trace/trace_events.c
index 53c8fd376a8..23d2972b22d 100644
--- a/kernel/trace/trace_events.c
+++ b/kernel/trace/trace_events.c
@@ -376,7 +376,7 @@ ftrace_event_seq_open(struct inode *inode, struct file *file)
 	const struct seq_operations *seq_ops;
 
 	if ((file->f_mode & FMODE_WRITE) &&
-	    !(file->f_flags & O_APPEND))
+	    (file->f_flags & O_TRUNC))
 		ftrace_clear_events();
 
 	seq_ops = inode->i_private;
-- 
GitLab


From fc4c73554c9d93b3e495f2f7acae1323b0d5db84 Mon Sep 17 00:00:00 2001
From: Matt Fleming <matt@console-pimps.org>
Date: Thu, 23 Jul 2009 17:16:14 +0100
Subject: [PATCH 0073/1153] ftrace: Fix the conditional that updates $ref_func

Fix the conditional that checks if we already have a $ref_func and that
the new function is weak. The code as previously checking whether either
condition was false, and we really need to only update $ref_func is both
cconditions are false.

Signed-off-by: Matt Fleming <matt@console-pimps.org>
LKML-Reference: <1248365775-25196-1-git-send-email-matt@console-pimps.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 scripts/recordmcount.pl | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/scripts/recordmcount.pl b/scripts/recordmcount.pl
index 7109e2b5bc0..16c5563b412 100755
--- a/scripts/recordmcount.pl
+++ b/scripts/recordmcount.pl
@@ -414,7 +414,7 @@ while (<IN>) {
 	    $read_function = 0;
 	} else {
 	    # if we already have a function, and this is weak, skip it
-	    if (!defined($ref_func) || !defined($weak{$text})) {
+	    if (!defined($ref_func) && !defined($weak{$text})) {
 		$ref_func = $text;
 	    }
 	}
-- 
GitLab


From bd171d5ffc5cb2ba471e8205c679ee9d12b90116 Mon Sep 17 00:00:00 2001
From: Matt Fleming <matt@console-pimps.org>
Date: Thu, 23 Jul 2009 17:16:15 +0100
Subject: [PATCH 0074/1153] ftrace: Only update $offset when we update
 $ref_func

The value of $offset should be the offset of $ref_func from the
beginning of the object file. Therefore, we should set both variables
together.

This fixes a bug I was hitting on sh where $offset (which is used to
calcualte the addends for the __mcount_loc entries) was being set
multiple times and didn't correspond to $ref_func's offset in the object
file. The addends in __mcount_loc were calculated incorrectly, resulting
in ftrace dynamically modifying addresses that weren't mcount call
sites.

Signed-off-by: Matt Fleming <matt@console-pimps.org>
LKML-Reference: <1248365775-25196-2-git-send-email-matt@console-pimps.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 scripts/recordmcount.pl | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/scripts/recordmcount.pl b/scripts/recordmcount.pl
index 16c5563b412..d29baa2e063 100755
--- a/scripts/recordmcount.pl
+++ b/scripts/recordmcount.pl
@@ -403,7 +403,6 @@ while (<IN>) {
     # section found, now is this a start of a function?
     } elsif ($read_function && /$function_regex/) {
 	$text_found = 1;
-	$offset = hex $1;
 	$text = $2;
 
 	# if this is either a local function or a weak function
@@ -412,10 +411,12 @@ while (<IN>) {
 	if (!defined($locals{$text}) && !defined($weak{$text})) {
 	    $ref_func = $text;
 	    $read_function = 0;
+	    $offset = hex $1;
 	} else {
 	    # if we already have a function, and this is weak, skip it
 	    if (!defined($ref_func) && !defined($weak{$text})) {
 		$ref_func = $text;
+		$offset = hex $1;
 	    }
 	}
     } elsif ($read_headers && /$mcount_section/) {
-- 
GitLab


From 82e12644cf5227dab15201fbcaf0ca6330ebd70f Mon Sep 17 00:00:00 2001
From: Tao Ma <tao.ma@oracle.com>
Date: Thu, 23 Jul 2009 08:12:58 +0800
Subject: [PATCH 0075/1153] ocfs2: Use ocfs2_rec_clusters in
 ocfs2_adjust_adjacent_records.

In ocfs2_adjust_adjacent_records, we will adjust adjacent records
according to the extent_list in the lower level. But actually
the lower level tree will either be a leaf or a branch. If we only
use ocfs2_is_empty_extent we will meet with some problem if the lower
tree is a branch (tree_depth > 1). So use !ocfs2_rec_clusters instead.
And actually only the leaf record can have holes. So add a BUG_ON
for non-leaf branch.

Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/alloc.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/fs/ocfs2/alloc.c b/fs/ocfs2/alloc.c
index 11085af7124..f9a3e894266 100644
--- a/fs/ocfs2/alloc.c
+++ b/fs/ocfs2/alloc.c
@@ -1914,7 +1914,8 @@ static void ocfs2_adjust_adjacent_records(struct ocfs2_extent_rec *left_rec,
 	 * immediately to their right.
 	 */
 	left_clusters = le32_to_cpu(right_child_el->l_recs[0].e_cpos);
-	if (ocfs2_is_empty_extent(&right_child_el->l_recs[0])) {
+	if (!ocfs2_rec_clusters(right_child_el, &right_child_el->l_recs[0])) {
+		BUG_ON(right_child_el->l_tree_depth);
 		BUG_ON(le16_to_cpu(right_child_el->l_next_free_rec) <= 1);
 		left_clusters = le32_to_cpu(right_child_el->l_recs[1].e_cpos);
 	}
-- 
GitLab


From b57ac2c43e66cb4aa76c9d2d0e9e0e04f19cc5a6 Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Wed, 22 Jul 2009 13:17:15 +0200
Subject: [PATCH 0076/1153] ocfs2: Make global quota files blocksize aligned

Change i_size of global quota files so that it always remains aligned to block
size. This is mainly because the end of quota block may contain checksum (if
checksumming is enabled) and it's a bit awkward for it to be "outside" of quota
file (and it makes life harder for ocfs2-tools).

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/quota_global.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c
index edfa60cd155..a66cb82fd6e 100644
--- a/fs/ocfs2/quota_global.c
+++ b/fs/ocfs2/quota_global.c
@@ -211,14 +211,17 @@ ssize_t ocfs2_quota_write(struct super_block *sb, int type,
 
 	mutex_lock_nested(&gqinode->i_mutex, I_MUTEX_QUOTA);
 	if (gqinode->i_size < off + len) {
+		loff_t rounded_end =
+				ocfs2_align_bytes_to_blocks(sb, off + len);
+
 		down_write(&OCFS2_I(gqinode)->ip_alloc_sem);
-		err = ocfs2_extend_no_holes(gqinode, off + len, off);
+		err = ocfs2_extend_no_holes(gqinode, rounded_end, off);
 		up_write(&OCFS2_I(gqinode)->ip_alloc_sem);
 		if (err < 0)
 			goto out;
 		err = ocfs2_simple_size_update(gqinode,
 					       oinfo->dqi_gqi_bh,
-					       off + len);
+					       rounded_end);
 		if (err < 0)
 			goto out;
 		new = 1;
-- 
GitLab


From 4b3fa1904c0d192461ebba692e4940a334b74353 Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Wed, 22 Jul 2009 13:17:16 +0200
Subject: [PATCH 0077/1153] ocfs2: Mark buffer uptodate before calling
 ocfs2_journal_access_dq()

In a code path extending local quota files we marked new header
buffer uptodate only after calling ocfs2_journal_access_dq() which
triggers a bug. Fix it and also call ocfs2 variant of the function
marking buffer uptodate.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/quota_local.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/fs/ocfs2/quota_local.c b/fs/ocfs2/quota_local.c
index 5a460fa8255..b624f9bc928 100644
--- a/fs/ocfs2/quota_local.c
+++ b/fs/ocfs2/quota_local.c
@@ -20,6 +20,7 @@
 #include "sysfile.h"
 #include "dlmglue.h"
 #include "quota.h"
+#include "uptodate.h"
 
 /* Number of local quota structures per block */
 static inline unsigned int ol_quota_entries_per_block(struct super_block *sb)
@@ -979,6 +980,8 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk(
 		mlog_errno(status);
 		goto out;
 	}
+	ocfs2_set_new_buffer_uptodate(lqinode, bh);
+
 	dchunk = (struct ocfs2_local_disk_chunk *)bh->b_data;
 
 	handle = ocfs2_start_trans(OCFS2_SB(sb), 2);
@@ -999,7 +1002,6 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk(
 	memset(dchunk->dqc_bitmap, 0,
 	       sb->s_blocksize - sizeof(struct ocfs2_local_disk_chunk) -
 	       OCFS2_QBLK_RESERVED_SPACE);
-	set_buffer_uptodate(bh);
 	unlock_buffer(bh);
 	status = ocfs2_journal_dirty(handle, bh);
 	if (status < 0) {
-- 
GitLab


From 0e7f387bf386c99e8ee322649fe4fc23b9cccc6c Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Wed, 22 Jul 2009 13:17:17 +0200
Subject: [PATCH 0078/1153] ocfs2: Initialize blocks allocated to local quota
 file

When we extend local quota file, we should initialize data
in newly allocated block. Firstly because on recovery we could
parse bogus data, secondly so that block checksums are properly
computed.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/quota_local.c | 98 +++++++++++++++++++++++++++++++++++-------
 1 file changed, 83 insertions(+), 15 deletions(-)

diff --git a/fs/ocfs2/quota_local.c b/fs/ocfs2/quota_local.c
index b624f9bc928..9d2993de108 100644
--- a/fs/ocfs2/quota_local.c
+++ b/fs/ocfs2/quota_local.c
@@ -941,7 +941,7 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk(
 	struct ocfs2_local_disk_chunk *dchunk;
 	int status;
 	handle_t *handle;
-	struct buffer_head *bh = NULL;
+	struct buffer_head *bh = NULL, *dbh = NULL;
 	u64 p_blkno;
 
 	/* We are protected by dqio_sem so no locking needed */
@@ -965,34 +965,32 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk(
 		mlog_errno(status);
 		goto out;
 	}
+	handle = ocfs2_start_trans(OCFS2_SB(sb), 3);
+	if (IS_ERR(handle)) {
+		status = PTR_ERR(handle);
+		mlog_errno(status);
+		goto out;
+	}
 
+	/* Initialize chunk header */
 	down_read(&OCFS2_I(lqinode)->ip_alloc_sem);
 	status = ocfs2_extent_map_get_blocks(lqinode, oinfo->dqi_blocks,
 					     &p_blkno, NULL, NULL);
 	up_read(&OCFS2_I(lqinode)->ip_alloc_sem);
 	if (status < 0) {
 		mlog_errno(status);
-		goto out;
+		goto out_trans;
 	}
 	bh = sb_getblk(sb, p_blkno);
 	if (!bh) {
 		status = -ENOMEM;
 		mlog_errno(status);
-		goto out;
+		goto out_trans;
 	}
-	ocfs2_set_new_buffer_uptodate(lqinode, bh);
-
 	dchunk = (struct ocfs2_local_disk_chunk *)bh->b_data;
-
-	handle = ocfs2_start_trans(OCFS2_SB(sb), 2);
-	if (IS_ERR(handle)) {
-		status = PTR_ERR(handle);
-		mlog_errno(status);
-		goto out;
-	}
-
+	ocfs2_set_new_buffer_uptodate(lqinode, bh);
 	status = ocfs2_journal_access_dq(handle, lqinode, bh,
-					 OCFS2_JOURNAL_ACCESS_WRITE);
+					 OCFS2_JOURNAL_ACCESS_CREATE);
 	if (status < 0) {
 		mlog_errno(status);
 		goto out_trans;
@@ -1009,6 +1007,38 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk(
 		goto out_trans;
 	}
 
+	/* Initialize new block with structures */
+	down_read(&OCFS2_I(lqinode)->ip_alloc_sem);
+	status = ocfs2_extent_map_get_blocks(lqinode, oinfo->dqi_blocks + 1,
+					     &p_blkno, NULL, NULL);
+	up_read(&OCFS2_I(lqinode)->ip_alloc_sem);
+	if (status < 0) {
+		mlog_errno(status);
+		goto out_trans;
+	}
+	dbh = sb_getblk(sb, p_blkno);
+	if (!dbh) {
+		status = -ENOMEM;
+		mlog_errno(status);
+		goto out_trans;
+	}
+	ocfs2_set_new_buffer_uptodate(lqinode, dbh);
+	status = ocfs2_journal_access_dq(handle, lqinode, dbh,
+					 OCFS2_JOURNAL_ACCESS_CREATE);
+	if (status < 0) {
+		mlog_errno(status);
+		goto out_trans;
+	}
+	lock_buffer(dbh);
+	memset(dbh->b_data, 0, sb->s_blocksize - OCFS2_QBLK_RESERVED_SPACE);
+	unlock_buffer(dbh);
+	status = ocfs2_journal_dirty(handle, dbh);
+	if (status < 0) {
+		mlog_errno(status);
+		goto out_trans;
+	}
+
+	/* Update local quotafile info */
 	oinfo->dqi_blocks += 2;
 	oinfo->dqi_chunks++;
 	status = ocfs2_local_write_info(sb, type);
@@ -1033,6 +1063,7 @@ out_trans:
 	ocfs2_commit_trans(OCFS2_SB(sb), handle);
 out:
 	brelse(bh);
+	brelse(dbh);
 	kmem_cache_free(ocfs2_qf_chunk_cachep, chunk);
 	return ERR_PTR(status);
 }
@@ -1050,6 +1081,8 @@ static struct ocfs2_quota_chunk *ocfs2_extend_local_quota_file(
 	struct ocfs2_local_disk_chunk *dchunk;
 	int epb = ol_quota_entries_per_block(sb);
 	unsigned int chunk_blocks;
+	struct buffer_head *bh;
+	u64 p_blkno;
 	int status;
 	handle_t *handle;
 
@@ -1077,12 +1110,46 @@ static struct ocfs2_quota_chunk *ocfs2_extend_local_quota_file(
 		mlog_errno(status);
 		goto out;
 	}
-	handle = ocfs2_start_trans(OCFS2_SB(sb), 2);
+
+	/* Get buffer from the just added block */
+	down_read(&OCFS2_I(lqinode)->ip_alloc_sem);
+	status = ocfs2_extent_map_get_blocks(lqinode, oinfo->dqi_blocks,
+					     &p_blkno, NULL, NULL);
+	up_read(&OCFS2_I(lqinode)->ip_alloc_sem);
+	if (status < 0) {
+		mlog_errno(status);
+		goto out;
+	}
+	bh = sb_getblk(sb, p_blkno);
+	if (!bh) {
+		status = -ENOMEM;
+		mlog_errno(status);
+		goto out;
+	}
+	ocfs2_set_new_buffer_uptodate(lqinode, bh);
+
+	handle = ocfs2_start_trans(OCFS2_SB(sb), 3);
 	if (IS_ERR(handle)) {
 		status = PTR_ERR(handle);
 		mlog_errno(status);
 		goto out;
 	}
+	/* Zero created block */
+	status = ocfs2_journal_access_dq(handle, lqinode, bh,
+				 OCFS2_JOURNAL_ACCESS_CREATE);
+	if (status < 0) {
+		mlog_errno(status);
+		goto out_trans;
+	}
+	lock_buffer(bh);
+	memset(bh->b_data, 0, sb->s_blocksize);
+	unlock_buffer(bh);
+	status = ocfs2_journal_dirty(handle, bh);
+	if (status < 0) {
+		mlog_errno(status);
+		goto out_trans;
+	}
+	/* Update chunk header */
 	status = ocfs2_journal_access_dq(handle, lqinode, chunk->qc_headerbh,
 				 OCFS2_JOURNAL_ACCESS_WRITE);
 	if (status < 0) {
@@ -1099,6 +1166,7 @@ static struct ocfs2_quota_chunk *ocfs2_extend_local_quota_file(
 		mlog_errno(status);
 		goto out_trans;
 	}
+	/* Update file header */
 	oinfo->dqi_blocks++;
 	status = ocfs2_local_write_info(sb, type);
 	if (status < 0) {
-- 
GitLab


From 7669f54c55df225cbb2db939a6c9f111445ffc1c Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Wed, 22 Jul 2009 13:17:18 +0200
Subject: [PATCH 0079/1153] ocfs2: Zero out padding of on disk dquot structure

Padding fields of on-disk dquot structure were not zeroed. Zero them
so that it's easier to use them later.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/quota_global.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c
index a66cb82fd6e..7248db68135 100644
--- a/fs/ocfs2/quota_global.c
+++ b/fs/ocfs2/quota_global.c
@@ -69,6 +69,7 @@ static void ocfs2_global_mem2diskdqb(void *dp, struct dquot *dquot)
 	d->dqb_curspace = cpu_to_le64(m->dqb_curspace);
 	d->dqb_btime = cpu_to_le64(m->dqb_btime);
 	d->dqb_itime = cpu_to_le64(m->dqb_itime);
+	d->dqb_pad1 = d->dqb_pad2 = 0;
 }
 
 static int ocfs2_global_is_id(void *dp, struct dquot *dquot)
-- 
GitLab


From 1c1d9793ff6720531c0125a28d321f283716e32f Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Wed, 22 Jul 2009 13:17:19 +0200
Subject: [PATCH 0080/1153] ocfs2: Fix initialization of blockcheck stats

We just set blockcheck stats to zeros but we should also
properly initialize the spinlock there.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/super.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/fs/ocfs2/super.c b/fs/ocfs2/super.c
index f2893878f8a..b0ee0fdf799 100644
--- a/fs/ocfs2/super.c
+++ b/fs/ocfs2/super.c
@@ -777,6 +777,7 @@ static int ocfs2_sb_probe(struct super_block *sb,
 		}
 		di = (struct ocfs2_dinode *) (*bh)->b_data;
 		memset(stats, 0, sizeof(struct ocfs2_blockcheck_stats));
+		spin_lock_init(&stats->b_lock);
 		status = ocfs2_verify_volume(di, *bh, blksize, stats);
 		if (status >= 0)
 			goto bail;
-- 
GitLab


From 4539f1df25bcd0fdf0d8a5e2c92de6bece83c7a0 Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Wed, 22 Jul 2009 13:17:20 +0200
Subject: [PATCH 0081/1153] ocfs2: Remove syncjiff field from quota info

syncjiff is just a converted value of syncms. Some places which
are updating syncms forgot to update syncjiff as well. Since the
conversion is just a simple division / multiplication and it does
not happen frequently, just remove the syncjiff field to avoid
forgotten conversions.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/quota.h        | 1 -
 fs/ocfs2/quota_global.c | 5 ++---
 2 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/fs/ocfs2/quota.h b/fs/ocfs2/quota.h
index 7365e2e0870..3fb96fcd4c8 100644
--- a/fs/ocfs2/quota.h
+++ b/fs/ocfs2/quota.h
@@ -50,7 +50,6 @@ struct ocfs2_mem_dqinfo {
 	unsigned int dqi_chunks;	/* Number of chunks in local quota file */
 	unsigned int dqi_blocks;	/* Number of blocks allocated for local quota file */
 	unsigned int dqi_syncms;	/* How often should we sync with other nodes */
-	unsigned int dqi_syncjiff;	/* Precomputed dqi_syncms in jiffies */
 	struct list_head dqi_chunk;	/* List of chunks */
 	struct inode *dqi_gqinode;	/* Global quota file inode */
 	struct ocfs2_lock_res dqi_gqlock;	/* Lock protecting quota information structure */
diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c
index 7248db68135..dab45467b5f 100644
--- a/fs/ocfs2/quota_global.c
+++ b/fs/ocfs2/quota_global.c
@@ -346,7 +346,6 @@ int ocfs2_global_read_info(struct super_block *sb, int type)
 	info->dqi_bgrace = le32_to_cpu(dinfo.dqi_bgrace);
 	info->dqi_igrace = le32_to_cpu(dinfo.dqi_igrace);
 	oinfo->dqi_syncms = le32_to_cpu(dinfo.dqi_syncms);
-	oinfo->dqi_syncjiff = msecs_to_jiffies(oinfo->dqi_syncms);
 	oinfo->dqi_gi.dqi_blocks = le32_to_cpu(dinfo.dqi_blocks);
 	oinfo->dqi_gi.dqi_free_blk = le32_to_cpu(dinfo.dqi_free_blk);
 	oinfo->dqi_gi.dqi_free_entry = le32_to_cpu(dinfo.dqi_free_entry);
@@ -356,7 +355,7 @@ int ocfs2_global_read_info(struct super_block *sb, int type)
 	oinfo->dqi_gi.dqi_qtree_depth = qtree_depth(&oinfo->dqi_gi);
 	INIT_DELAYED_WORK(&oinfo->dqi_sync_work, qsync_work_fn);
 	queue_delayed_work(ocfs2_quota_wq, &oinfo->dqi_sync_work,
-			   oinfo->dqi_syncjiff);
+			   msecs_to_jiffies(oinfo->dqi_syncms));
 
 out_err:
 	mlog_exit(status);
@@ -611,7 +610,7 @@ static void qsync_work_fn(struct work_struct *work)
 
 	dquot_scan_active(sb, ocfs2_sync_dquot_helper, oinfo->dqi_type);
 	queue_delayed_work(ocfs2_quota_wq, &oinfo->dqi_sync_work,
-			   oinfo->dqi_syncjiff);
+			   msecs_to_jiffies(oinfo->dqi_syncms));
 }
 
 /*
-- 
GitLab


From 0584974a77796581eb3a64b6c5005edac4a95128 Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Wed, 22 Jul 2009 13:17:21 +0200
Subject: [PATCH 0082/1153] ocfs2: Define credit counts for quota operations

Numbers of needed credits for some quota operations were written
as raw numbers. Create appropriate defines instead.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/journal.h      | 13 ++++++++++---
 fs/ocfs2/quota_global.c | 18 +++++++++++++-----
 fs/ocfs2/quota_local.c  | 16 ++++++++++++----
 3 files changed, 35 insertions(+), 12 deletions(-)

diff --git a/fs/ocfs2/journal.h b/fs/ocfs2/journal.h
index 81e8abcd246..4a4d3b55fd2 100644
--- a/fs/ocfs2/journal.h
+++ b/fs/ocfs2/journal.h
@@ -330,20 +330,27 @@ int                  ocfs2_journal_dirty(handle_t *handle,
 /* extended attribute block update */
 #define OCFS2_XATTR_BLOCK_UPDATE_CREDITS 1
 
+/* Update of a single quota block */
+#define OCFS2_QUOTA_BLOCK_UPDATE_CREDITS 1
+
 /* global quotafile inode update, data block */
-#define OCFS2_QINFO_WRITE_CREDITS (OCFS2_INODE_UPDATE_CREDITS + 1)
+#define OCFS2_QINFO_WRITE_CREDITS (OCFS2_INODE_UPDATE_CREDITS + \
+				   OCFS2_QUOTA_BLOCK_UPDATE_CREDITS)
 
+#define OCFS2_LOCAL_QINFO_WRITE_CREDITS OCFS2_QUOTA_BLOCK_UPDATE_CREDITS
 /*
  * The two writes below can accidentally see global info dirty due
  * to set_info() quotactl so make them prepared for the writes.
  */
 /* quota data block, global info */
 /* Write to local quota file */
-#define OCFS2_QWRITE_CREDITS (OCFS2_QINFO_WRITE_CREDITS + 1)
+#define OCFS2_QWRITE_CREDITS (OCFS2_QINFO_WRITE_CREDITS + \
+			      OCFS2_QUOTA_BLOCK_UPDATE_CREDITS)
 
 /* global quota data block, local quota data block, global quota inode,
  * global quota info */
-#define OCFS2_QSYNC_CREDITS (OCFS2_INODE_UPDATE_CREDITS + 3)
+#define OCFS2_QSYNC_CREDITS (OCFS2_QINFO_WRITE_CREDITS + \
+			     2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS)
 
 static inline int ocfs2_quota_trans_credits(struct super_block *sb)
 {
diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c
index dab45467b5f..cc8785cf8f6 100644
--- a/fs/ocfs2/quota_global.c
+++ b/fs/ocfs2/quota_global.c
@@ -648,10 +648,15 @@ int ocfs2_calc_qdel_credits(struct super_block *sb, int type)
 		return 0;
 
 	oinfo = sb_dqinfo(sb, type)->dqi_priv;
-	/* We modify tree, leaf block, global info, local chunk header,
-	 * global and local inode */
-	return oinfo->dqi_gi.dqi_qtree_depth + 2 + 1 +
-	       2 * OCFS2_INODE_UPDATE_CREDITS;
+	/*
+	 * We modify tree, leaf block, global info, local chunk header,
+	 * global and local inode; OCFS2_QINFO_WRITE_CREDITS already
+	 * accounts for inode update
+	 */
+	return oinfo->dqi_gi.dqi_qtree_depth +
+	       OCFS2_QINFO_WRITE_CREDITS +
+	       2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS +
+	       OCFS2_INODE_UPDATE_CREDITS;
 }
 
 static int ocfs2_release_dquot(struct dquot *dquot)
@@ -701,7 +706,10 @@ int ocfs2_calc_qinit_credits(struct super_block *sb, int type)
 	 * global file we can modify info, tree and leaf block */
 	return ocfs2_calc_extend_credits(sb, &lfe->id2.i_list, 0) +
 	       ocfs2_calc_extend_credits(sb, &gfe->id2.i_list, 0) +
-	       3 + oinfo->dqi_gi.dqi_qtree_depth + 2;
+	       OCFS2_LOCAL_QINFO_WRITE_CREDITS +
+	       2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS +
+	       oinfo->dqi_gi.dqi_qtree_depth +
+	       2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS;
 }
 
 static int ocfs2_acquire_dquot(struct dquot *dquot)
diff --git a/fs/ocfs2/quota_local.c b/fs/ocfs2/quota_local.c
index 9d2993de108..bdb09cb6e1f 100644
--- a/fs/ocfs2/quota_local.c
+++ b/fs/ocfs2/quota_local.c
@@ -101,7 +101,8 @@ static int ocfs2_modify_bh(struct inode *inode, struct buffer_head *bh,
 	handle_t *handle;
 	int status;
 
-	handle = ocfs2_start_trans(OCFS2_SB(sb), 1);
+	handle = ocfs2_start_trans(OCFS2_SB(sb),
+				   OCFS2_QUOTA_BLOCK_UPDATE_CREDITS);
 	if (IS_ERR(handle)) {
 		status = PTR_ERR(handle);
 		mlog_errno(status);
@@ -611,7 +612,8 @@ int ocfs2_finish_quota_recovery(struct ocfs2_super *osb,
 			goto out_bh;
 		/* Mark quota file as clean if we are recovering quota file of
 		 * some other node. */
-		handle = ocfs2_start_trans(osb, 1);
+		handle = ocfs2_start_trans(osb,
+					   OCFS2_LOCAL_QINFO_WRITE_CREDITS);
 		if (IS_ERR(handle)) {
 			status = PTR_ERR(handle);
 			mlog_errno(status);
@@ -965,7 +967,10 @@ static struct ocfs2_quota_chunk *ocfs2_local_quota_add_chunk(
 		mlog_errno(status);
 		goto out;
 	}
-	handle = ocfs2_start_trans(OCFS2_SB(sb), 3);
+	/* Local quota info and two new blocks we initialize */
+	handle = ocfs2_start_trans(OCFS2_SB(sb),
+			OCFS2_LOCAL_QINFO_WRITE_CREDITS +
+			2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS);
 	if (IS_ERR(handle)) {
 		status = PTR_ERR(handle);
 		mlog_errno(status);
@@ -1128,7 +1133,10 @@ static struct ocfs2_quota_chunk *ocfs2_extend_local_quota_file(
 	}
 	ocfs2_set_new_buffer_uptodate(lqinode, bh);
 
-	handle = ocfs2_start_trans(OCFS2_SB(sb), 3);
+	/* Local quota info, chunk header and the new block we initialize */
+	handle = ocfs2_start_trans(OCFS2_SB(sb),
+			OCFS2_LOCAL_QINFO_WRITE_CREDITS +
+			2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS);
 	if (IS_ERR(handle)) {
 		status = PTR_ERR(handle);
 		mlog_errno(status);
-- 
GitLab


From 963030817060e4f109be1993b9ae8f81dbf5e11a Mon Sep 17 00:00:00 2001
From: Josef Bacik <josef@redhat.com>
Date: Mon, 13 Jul 2009 21:29:25 -0400
Subject: [PATCH 0083/1153] Btrfs: use hybrid extents+bitmap rb tree for free
 space

Currently btrfs has a problem where it can use a ridiculous amount of RAM simply
tracking free space.  As free space gets fragmented, we end up with thousands of
entries on an rb-tree per block group, which usually spans 1 gig of area.  Since
we currently don't ever flush free space cache back to disk this gets to be a
bit unweildly on large fs's with lots of fragmentation.

This patch solves this problem by using PAGE_SIZE bitmaps for parts of the free
space cache.  Initially we calculate a threshold of extent entries we can
handle, which is however many extent entries we can cram into 16k of ram.  The
maximum amount of RAM that should ever be used to track 1 gigabyte of diskspace
will be 32k of RAM, which scales much better than we did before.

Once we pass the extent threshold, we start adding bitmaps and using those
instead for tracking the free space.  This patch also makes it so that any free
space thats less than 4 * sectorsize we go ahead and put into a bitmap.  This is
nice since we try and allocate out of the front of a block group, so if the
front of a block group is heavily fragmented and then has a huge chunk of free
space at the end, we go ahead and add the fragmented areas to bitmaps and use a
normal extent entry to track the big chunk at the back of the block group.

I've also taken the opportunity to revamp how we search for free space.
Previously we indexed free space via an offset indexed rb tree and a bytes
indexed rb tree.  I've dropped the bytes indexed rb tree and use only the offset
indexed rb tree.  This cuts the number of tree operations we were doing
previously down by half, and gives us a little bit of a better allocation
pattern since we will always start from a specific offset and search forward
from there, instead of searching for the size we need and try and get it as
close as possible to the offset we want.

I've given this a healthy amount of testing pre-new format stuff, as well as
post-new format stuff.  I've booted up my fedora box which is installed on btrfs
with this patch and ran with it for a few days without issues.  I've not seen
any performance regressions in any of my tests.

Since the last patch Yan Zheng fixed a problem where we could have overlapping
entries, so updating their offset inline would cause problems.  Thanks,

Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/ctree.h            |    8 +-
 fs/btrfs/extent-tree.c      |   25 +-
 fs/btrfs/free-space-cache.c | 1001 +++++++++++++++++++++++++++--------
 fs/btrfs/free-space-cache.h |    8 +
 4 files changed, 826 insertions(+), 216 deletions(-)

diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h
index da0763135bf..0cbf3491bb7 100644
--- a/fs/btrfs/ctree.h
+++ b/fs/btrfs/ctree.h
@@ -709,6 +709,9 @@ struct btrfs_free_cluster {
 	/* first extent starting offset */
 	u64 window_start;
 
+	/* if this cluster simply points at a bitmap in the block group */
+	bool points_to_bitmap;
+
 	struct btrfs_block_group_cache *block_group;
 	/*
 	 * when a cluster is allocated from a block group, we put the
@@ -726,6 +729,10 @@ struct btrfs_block_group_cache {
 	u64 pinned;
 	u64 reserved;
 	u64 flags;
+	u64 sectorsize;
+	int extents_thresh;
+	int free_extents;
+	int total_bitmaps;
 	int cached;
 	int ro;
 	int dirty;
@@ -734,7 +741,6 @@ struct btrfs_block_group_cache {
 
 	/* free space cache stuff */
 	spinlock_t tree_lock;
-	struct rb_root free_space_bytes;
 	struct rb_root free_space_offset;
 
 	/* block group cache stuff */
diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index 62a332d34fd..98697be6bdd 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -3649,7 +3649,6 @@ refill_cluster:
 			goto loop;
 checks:
 		search_start = stripe_align(root, offset);
-
 		/* move on to the next group */
 		if (search_start + num_bytes >= search_end) {
 			btrfs_add_free_space(block_group, offset, num_bytes);
@@ -7040,6 +7039,16 @@ int btrfs_read_block_groups(struct btrfs_root *root)
 		mutex_init(&cache->cache_mutex);
 		INIT_LIST_HEAD(&cache->list);
 		INIT_LIST_HEAD(&cache->cluster_list);
+		cache->sectorsize = root->sectorsize;
+
+		/*
+		 * we only want to have 32k of ram per block group for keeping
+		 * track of free space, and if we pass 1/2 of that we want to
+		 * start converting things over to using bitmaps
+		 */
+		cache->extents_thresh = ((1024 * 32) / 2) /
+			sizeof(struct btrfs_free_space);
+
 		read_extent_buffer(leaf, &cache->item,
 				   btrfs_item_ptr_offset(leaf, path->slots[0]),
 				   sizeof(cache->item));
@@ -7091,6 +7100,15 @@ int btrfs_make_block_group(struct btrfs_trans_handle *trans,
 	cache->key.objectid = chunk_offset;
 	cache->key.offset = size;
 	cache->key.type = BTRFS_BLOCK_GROUP_ITEM_KEY;
+	cache->sectorsize = root->sectorsize;
+
+	/*
+	 * we only want to have 32k of ram per block group for keeping track
+	 * of free space, and if we pass 1/2 of that we want to start
+	 * converting things over to using bitmaps
+	 */
+	cache->extents_thresh = ((1024 * 32) / 2) /
+		sizeof(struct btrfs_free_space);
 	atomic_set(&cache->count, 1);
 	spin_lock_init(&cache->lock);
 	spin_lock_init(&cache->tree_lock);
@@ -7103,6 +7121,11 @@ int btrfs_make_block_group(struct btrfs_trans_handle *trans,
 	cache->flags = type;
 	btrfs_set_block_group_flags(&cache->item, type);
 
+	cache->cached = 1;
+	ret = btrfs_add_free_space(cache, chunk_offset, size);
+	BUG_ON(ret);
+	remove_sb_from_cache(root, cache);
+
 	ret = update_space_info(root->fs_info, cache->flags, size, bytes_used,
 				&cache->space_info);
 	BUG_ON(ret);
diff --git a/fs/btrfs/free-space-cache.c b/fs/btrfs/free-space-cache.c
index 4538e48581a..ab8cad8b46c 100644
--- a/fs/btrfs/free-space-cache.c
+++ b/fs/btrfs/free-space-cache.c
@@ -16,45 +16,46 @@
  * Boston, MA 021110-1307, USA.
  */
 
+#include <linux/pagemap.h>
 #include <linux/sched.h>
+#include <linux/math64.h>
 #include "ctree.h"
 #include "free-space-cache.h"
 #include "transaction.h"
 
-struct btrfs_free_space {
-	struct rb_node bytes_index;
-	struct rb_node offset_index;
-	u64 offset;
-	u64 bytes;
-};
+#define BITS_PER_BITMAP		(PAGE_CACHE_SIZE * 8)
+#define MAX_CACHE_BYTES_PER_GIG	(32 * 1024)
 
-static int tree_insert_offset(struct rb_root *root, u64 offset,
-			      struct rb_node *node)
+static inline unsigned long offset_to_bit(u64 bitmap_start, u64 sectorsize,
+					  u64 offset)
 {
-	struct rb_node **p = &root->rb_node;
-	struct rb_node *parent = NULL;
-	struct btrfs_free_space *info;
+	BUG_ON(offset < bitmap_start);
+	offset -= bitmap_start;
+	return (unsigned long)(div64_u64(offset, sectorsize));
+}
 
-	while (*p) {
-		parent = *p;
-		info = rb_entry(parent, struct btrfs_free_space, offset_index);
+static inline unsigned long bytes_to_bits(u64 bytes, u64 sectorsize)
+{
+	return (unsigned long)(div64_u64(bytes, sectorsize));
+}
 
-		if (offset < info->offset)
-			p = &(*p)->rb_left;
-		else if (offset > info->offset)
-			p = &(*p)->rb_right;
-		else
-			return -EEXIST;
-	}
+static inline u64 offset_to_bitmap(struct btrfs_block_group_cache *block_group,
+				   u64 offset)
+{
+	u64 bitmap_start;
+	u64 bytes_per_bitmap;
 
-	rb_link_node(node, parent, p);
-	rb_insert_color(node, root);
+	bytes_per_bitmap = BITS_PER_BITMAP * block_group->sectorsize;
+	bitmap_start = offset - block_group->key.objectid;
+	bitmap_start = div64_u64(bitmap_start, bytes_per_bitmap);
+	bitmap_start *= bytes_per_bitmap;
+	bitmap_start += block_group->key.objectid;
 
-	return 0;
+	return bitmap_start;
 }
 
-static int tree_insert_bytes(struct rb_root *root, u64 bytes,
-			     struct rb_node *node)
+static int tree_insert_offset(struct rb_root *root, u64 offset,
+			      struct rb_node *node, int bitmap)
 {
 	struct rb_node **p = &root->rb_node;
 	struct rb_node *parent = NULL;
@@ -62,12 +63,34 @@ static int tree_insert_bytes(struct rb_root *root, u64 bytes,
 
 	while (*p) {
 		parent = *p;
-		info = rb_entry(parent, struct btrfs_free_space, bytes_index);
+		info = rb_entry(parent, struct btrfs_free_space, offset_index);
 
-		if (bytes < info->bytes)
+		if (offset < info->offset) {
 			p = &(*p)->rb_left;
-		else
+		} else if (offset > info->offset) {
 			p = &(*p)->rb_right;
+		} else {
+			/*
+			 * we could have a bitmap entry and an extent entry
+			 * share the same offset.  If this is the case, we want
+			 * the extent entry to always be found first if we do a
+			 * linear search through the tree, since we want to have
+			 * the quickest allocation time, and allocating from an
+			 * extent is faster than allocating from a bitmap.  So
+			 * if we're inserting a bitmap and we find an entry at
+			 * this offset, we want to go right, or after this entry
+			 * logically.  If we are inserting an extent and we've
+			 * found a bitmap, we want to go left, or before
+			 * logically.
+			 */
+			if (bitmap) {
+				WARN_ON(info->bitmap);
+				p = &(*p)->rb_right;
+			} else {
+				WARN_ON(!info->bitmap);
+				p = &(*p)->rb_left;
+			}
+		}
 	}
 
 	rb_link_node(node, parent, p);
@@ -79,110 +102,142 @@ static int tree_insert_bytes(struct rb_root *root, u64 bytes,
 /*
  * searches the tree for the given offset.
  *
- * fuzzy == 1: this is used for allocations where we are given a hint of where
- * to look for free space.  Because the hint may not be completely on an offset
- * mark, or the hint may no longer point to free space we need to fudge our
- * results a bit.  So we look for free space starting at or after offset with at
- * least bytes size.  We prefer to find as close to the given offset as we can.
- * Also if the offset is within a free space range, then we will return the free
- * space that contains the given offset, which means we can return a free space
- * chunk with an offset before the provided offset.
- *
- * fuzzy == 0: this is just a normal tree search.  Give us the free space that
- * starts at the given offset which is at least bytes size, and if its not there
- * return NULL.
+ * fuzzy - If this is set, then we are trying to make an allocation, and we just
+ * want a section that has at least bytes size and comes at or after the given
+ * offset.
  */
-static struct btrfs_free_space *tree_search_offset(struct rb_root *root,
-						   u64 offset, u64 bytes,
-						   int fuzzy)
+static struct btrfs_free_space *
+tree_search_offset(struct btrfs_block_group_cache *block_group,
+		   u64 offset, int bitmap_only, int fuzzy)
 {
-	struct rb_node *n = root->rb_node;
-	struct btrfs_free_space *entry, *ret = NULL;
+	struct rb_node *n = block_group->free_space_offset.rb_node;
+	struct btrfs_free_space *entry, *prev = NULL;
+
+	/* find entry that is closest to the 'offset' */
+	while (1) {
+		if (!n) {
+			entry = NULL;
+			break;
+		}
 
-	while (n) {
 		entry = rb_entry(n, struct btrfs_free_space, offset_index);
+		prev = entry;
 
-		if (offset < entry->offset) {
-			if (fuzzy &&
-			    (!ret || entry->offset < ret->offset) &&
-			    (bytes <= entry->bytes))
-				ret = entry;
+		if (offset < entry->offset)
 			n = n->rb_left;
-		} else if (offset > entry->offset) {
-			if (fuzzy &&
-			    (entry->offset + entry->bytes - 1) >= offset &&
-			    bytes <= entry->bytes) {
-				ret = entry;
-				break;
-			}
+		else if (offset > entry->offset)
 			n = n->rb_right;
-		} else {
-			if (bytes > entry->bytes) {
-				n = n->rb_right;
-				continue;
-			}
-			ret = entry;
+		else
 			break;
-		}
 	}
 
-	return ret;
-}
-
-/*
- * return a chunk at least bytes size, as close to offset that we can get.
- */
-static struct btrfs_free_space *tree_search_bytes(struct rb_root *root,
-						  u64 offset, u64 bytes)
-{
-	struct rb_node *n = root->rb_node;
-	struct btrfs_free_space *entry, *ret = NULL;
+	if (bitmap_only) {
+		if (!entry)
+			return NULL;
+		if (entry->bitmap)
+			return entry;
 
-	while (n) {
-		entry = rb_entry(n, struct btrfs_free_space, bytes_index);
+		/*
+		 * bitmap entry and extent entry may share same offset,
+		 * in that case, bitmap entry comes after extent entry.
+		 */
+		n = rb_next(n);
+		if (!n)
+			return NULL;
+		entry = rb_entry(n, struct btrfs_free_space, offset_index);
+		if (entry->offset != offset)
+			return NULL;
 
-		if (bytes < entry->bytes) {
+		WARN_ON(!entry->bitmap);
+		return entry;
+	} else if (entry) {
+		if (entry->bitmap) {
 			/*
-			 * We prefer to get a hole size as close to the size we
-			 * are asking for so we don't take small slivers out of
-			 * huge holes, but we also want to get as close to the
-			 * offset as possible so we don't have a whole lot of
-			 * fragmentation.
+			 * if previous extent entry covers the offset,
+			 * we should return it instead of the bitmap entry
 			 */
-			if (offset <= entry->offset) {
-				if (!ret)
-					ret = entry;
-				else if (entry->bytes < ret->bytes)
-					ret = entry;
-				else if (entry->offset < ret->offset)
-					ret = entry;
+			n = &entry->offset_index;
+			while (1) {
+				n = rb_prev(n);
+				if (!n)
+					break;
+				prev = rb_entry(n, struct btrfs_free_space,
+						offset_index);
+				if (!prev->bitmap) {
+					if (prev->offset + prev->bytes > offset)
+						entry = prev;
+					break;
+				}
 			}
-			n = n->rb_left;
-		} else if (bytes > entry->bytes) {
-			n = n->rb_right;
+		}
+		return entry;
+	}
+
+	if (!prev)
+		return NULL;
+
+	/* find last entry before the 'offset' */
+	entry = prev;
+	if (entry->offset > offset) {
+		n = rb_prev(&entry->offset_index);
+		if (n) {
+			entry = rb_entry(n, struct btrfs_free_space,
+					offset_index);
+			BUG_ON(entry->offset > offset);
 		} else {
-			/*
-			 * Ok we may have multiple chunks of the wanted size,
-			 * so we don't want to take the first one we find, we
-			 * want to take the one closest to our given offset, so
-			 * keep searching just in case theres a better match.
-			 */
-			n = n->rb_right;
-			if (offset > entry->offset)
-				continue;
-			else if (!ret || entry->offset < ret->offset)
-				ret = entry;
+			if (fuzzy)
+				return entry;
+			else
+				return NULL;
 		}
 	}
 
-	return ret;
+	if (entry->bitmap) {
+		n = &entry->offset_index;
+		while (1) {
+			n = rb_prev(n);
+			if (!n)
+				break;
+			prev = rb_entry(n, struct btrfs_free_space,
+					offset_index);
+			if (!prev->bitmap) {
+				if (prev->offset + prev->bytes > offset)
+					return prev;
+				break;
+			}
+		}
+		if (entry->offset + BITS_PER_BITMAP *
+		    block_group->sectorsize > offset)
+			return entry;
+	} else if (entry->offset + entry->bytes > offset)
+		return entry;
+
+	if (!fuzzy)
+		return NULL;
+
+	while (1) {
+		if (entry->bitmap) {
+			if (entry->offset + BITS_PER_BITMAP *
+			    block_group->sectorsize > offset)
+				break;
+		} else {
+			if (entry->offset + entry->bytes > offset)
+				break;
+		}
+
+		n = rb_next(&entry->offset_index);
+		if (!n)
+			return NULL;
+		entry = rb_entry(n, struct btrfs_free_space, offset_index);
+	}
+	return entry;
 }
 
 static void unlink_free_space(struct btrfs_block_group_cache *block_group,
 			      struct btrfs_free_space *info)
 {
 	rb_erase(&info->offset_index, &block_group->free_space_offset);
-	rb_erase(&info->bytes_index, &block_group->free_space_bytes);
+	block_group->free_extents--;
 }
 
 static int link_free_space(struct btrfs_block_group_cache *block_group,
@@ -190,17 +245,311 @@ static int link_free_space(struct btrfs_block_group_cache *block_group,
 {
 	int ret = 0;
 
-
-	BUG_ON(!info->bytes);
+	BUG_ON(!info->bitmap && !info->bytes);
 	ret = tree_insert_offset(&block_group->free_space_offset, info->offset,
-				 &info->offset_index);
+				 &info->offset_index, (info->bitmap != NULL));
 	if (ret)
 		return ret;
 
-	ret = tree_insert_bytes(&block_group->free_space_bytes, info->bytes,
-				&info->bytes_index);
-	if (ret)
-		return ret;
+	block_group->free_extents++;
+	return ret;
+}
+
+static void recalculate_thresholds(struct btrfs_block_group_cache *block_group)
+{
+	u64 max_bytes, possible_bytes;
+
+	/*
+	 * The goal is to keep the total amount of memory used per 1gb of space
+	 * at or below 32k, so we need to adjust how much memory we allow to be
+	 * used by extent based free space tracking
+	 */
+	max_bytes = MAX_CACHE_BYTES_PER_GIG *
+		(div64_u64(block_group->key.offset, 1024 * 1024 * 1024));
+
+	possible_bytes = (block_group->total_bitmaps * PAGE_CACHE_SIZE) +
+		(sizeof(struct btrfs_free_space) *
+		 block_group->extents_thresh);
+
+	if (possible_bytes > max_bytes) {
+		int extent_bytes = max_bytes -
+			(block_group->total_bitmaps * PAGE_CACHE_SIZE);
+
+		if (extent_bytes <= 0) {
+			block_group->extents_thresh = 0;
+			return;
+		}
+
+		block_group->extents_thresh = extent_bytes /
+			(sizeof(struct btrfs_free_space));
+	}
+}
+
+static void bitmap_clear_bits(struct btrfs_free_space *info, u64 offset, u64 bytes,
+			      u64 sectorsize)
+{
+	unsigned long start, end;
+	unsigned long i;
+
+	start = offset_to_bit(info->offset, sectorsize, offset);
+	end = start + bytes_to_bits(bytes, sectorsize);
+	BUG_ON(end > BITS_PER_BITMAP);
+
+	for (i = start; i < end; i++)
+		clear_bit(i, info->bitmap);
+
+	info->bytes -= bytes;
+}
+
+static void bitmap_set_bits(struct btrfs_free_space *info, u64 offset, u64 bytes,
+			    u64 sectorsize)
+{
+	unsigned long start, end;
+	unsigned long i;
+
+	start = offset_to_bit(info->offset, sectorsize, offset);
+	end = start + bytes_to_bits(bytes, sectorsize);
+	BUG_ON(end > BITS_PER_BITMAP);
+
+	for (i = start; i < end; i++)
+		set_bit(i, info->bitmap);
+
+	info->bytes += bytes;
+}
+
+static int search_bitmap(struct btrfs_block_group_cache *block_group,
+			 struct btrfs_free_space *bitmap_info, u64 *offset,
+			 u64 *bytes)
+{
+	unsigned long found_bits = 0;
+	unsigned long bits, i;
+	unsigned long next_zero;
+
+	i = offset_to_bit(bitmap_info->offset, block_group->sectorsize,
+			  max_t(u64, *offset, bitmap_info->offset));
+	bits = bytes_to_bits(*bytes, block_group->sectorsize);
+
+	for (i = find_next_bit(bitmap_info->bitmap, BITS_PER_BITMAP, i);
+	     i < BITS_PER_BITMAP;
+	     i = find_next_bit(bitmap_info->bitmap, BITS_PER_BITMAP, i + 1)) {
+		next_zero = find_next_zero_bit(bitmap_info->bitmap,
+					       BITS_PER_BITMAP, i);
+		if ((next_zero - i) >= bits) {
+			found_bits = next_zero - i;
+			break;
+		}
+		i = next_zero;
+	}
+
+	if (found_bits) {
+		*offset = (u64)(i * block_group->sectorsize) +
+			bitmap_info->offset;
+		*bytes = (u64)(found_bits) * block_group->sectorsize;
+		return 0;
+	}
+
+	return -1;
+}
+
+static struct btrfs_free_space *find_free_space(struct btrfs_block_group_cache
+						*block_group, u64 *offset,
+						u64 *bytes, int debug)
+{
+	struct btrfs_free_space *entry;
+	struct rb_node *node;
+	int ret;
+
+	if (!block_group->free_space_offset.rb_node)
+		return NULL;
+
+	entry = tree_search_offset(block_group,
+				   offset_to_bitmap(block_group, *offset),
+				   0, 1);
+	if (!entry)
+		return NULL;
+
+	for (node = &entry->offset_index; node; node = rb_next(node)) {
+		entry = rb_entry(node, struct btrfs_free_space, offset_index);
+		if (entry->bytes < *bytes)
+			continue;
+
+		if (entry->bitmap) {
+			ret = search_bitmap(block_group, entry, offset, bytes);
+			if (!ret)
+				return entry;
+			continue;
+		}
+
+		*offset = entry->offset;
+		*bytes = entry->bytes;
+		return entry;
+	}
+
+	return NULL;
+}
+
+static void add_new_bitmap(struct btrfs_block_group_cache *block_group,
+			   struct btrfs_free_space *info, u64 offset)
+{
+	u64 bytes_per_bg = BITS_PER_BITMAP * block_group->sectorsize;
+	int max_bitmaps = (int)div64_u64(block_group->key.offset +
+					 bytes_per_bg - 1, bytes_per_bg);
+	BUG_ON(block_group->total_bitmaps >= max_bitmaps);
+
+	info->offset = offset_to_bitmap(block_group, offset);
+	link_free_space(block_group, info);
+	block_group->total_bitmaps++;
+
+	recalculate_thresholds(block_group);
+}
+
+static noinline int remove_from_bitmap(struct btrfs_block_group_cache *block_group,
+			      struct btrfs_free_space *bitmap_info,
+			      u64 *offset, u64 *bytes)
+{
+	u64 end;
+
+again:
+	end = bitmap_info->offset +
+		(u64)(BITS_PER_BITMAP * block_group->sectorsize) - 1;
+
+	if (*offset > bitmap_info->offset && *offset + *bytes > end) {
+		bitmap_clear_bits(bitmap_info, *offset,
+				  end - *offset + 1, block_group->sectorsize);
+		*bytes -= end - *offset + 1;
+		*offset = end + 1;
+	} else if (*offset >= bitmap_info->offset && *offset + *bytes <= end) {
+		bitmap_clear_bits(bitmap_info, *offset,
+				  *bytes, block_group->sectorsize);
+		*bytes = 0;
+	}
+
+	if (*bytes) {
+		if (!bitmap_info->bytes) {
+			unlink_free_space(block_group, bitmap_info);
+			kfree(bitmap_info->bitmap);
+			kfree(bitmap_info);
+			block_group->total_bitmaps--;
+			recalculate_thresholds(block_group);
+		}
+
+		bitmap_info = tree_search_offset(block_group,
+						 offset_to_bitmap(block_group,
+								  *offset),
+						 1, 0);
+		if (!bitmap_info)
+			return -EINVAL;
+
+		if (!bitmap_info->bitmap)
+			return -EAGAIN;
+
+		goto again;
+	} else if (!bitmap_info->bytes) {
+		unlink_free_space(block_group, bitmap_info);
+		kfree(bitmap_info->bitmap);
+		kfree(bitmap_info);
+		block_group->total_bitmaps--;
+		recalculate_thresholds(block_group);
+	}
+
+	return 0;
+}
+
+static int insert_into_bitmap(struct btrfs_block_group_cache *block_group,
+			      struct btrfs_free_space *info)
+{
+	struct btrfs_free_space *bitmap_info;
+	int added = 0;
+	u64 bytes, offset, end;
+	int ret;
+
+	/*
+	 * If we are below the extents threshold then we can add this as an
+	 * extent, and don't have to deal with the bitmap
+	 */
+	if (block_group->free_extents < block_group->extents_thresh &&
+	    info->bytes > block_group->sectorsize * 4)
+		return 0;
+
+	/*
+	 * some block groups are so tiny they can't be enveloped by a bitmap, so
+	 * don't even bother to create a bitmap for this
+	 */
+	if (BITS_PER_BITMAP * block_group->sectorsize >
+	    block_group->key.offset)
+		return 0;
+
+	bytes = info->bytes;
+	offset = info->offset;
+
+again:
+	bitmap_info = tree_search_offset(block_group,
+					 offset_to_bitmap(block_group, offset),
+					 1, 0);
+	if (!bitmap_info) {
+		BUG_ON(added);
+		goto new_bitmap;
+	}
+
+	end = bitmap_info->offset +
+		(u64)(BITS_PER_BITMAP * block_group->sectorsize);
+
+	if (offset >= bitmap_info->offset && offset + bytes > end) {
+		bitmap_set_bits(bitmap_info, offset, end - offset,
+				block_group->sectorsize);
+		bytes -= end - offset;
+		offset = end;
+		added = 0;
+	} else if (offset >= bitmap_info->offset && offset + bytes <= end) {
+		bitmap_set_bits(bitmap_info, offset, bytes,
+				block_group->sectorsize);
+		bytes = 0;
+	} else {
+		BUG();
+	}
+
+	if (!bytes) {
+		ret = 1;
+		goto out;
+	} else
+		goto again;
+
+new_bitmap:
+	if (info && info->bitmap) {
+		add_new_bitmap(block_group, info, offset);
+		added = 1;
+		info = NULL;
+		goto again;
+	} else {
+		spin_unlock(&block_group->tree_lock);
+
+		/* no pre-allocated info, allocate a new one */
+		if (!info) {
+			info = kzalloc(sizeof(struct btrfs_free_space),
+				       GFP_NOFS);
+			if (!info) {
+				spin_lock(&block_group->tree_lock);
+				ret = -ENOMEM;
+				goto out;
+			}
+		}
+
+		/* allocate the bitmap */
+		info->bitmap = kzalloc(PAGE_CACHE_SIZE, GFP_NOFS);
+		spin_lock(&block_group->tree_lock);
+		if (!info->bitmap) {
+			ret = -ENOMEM;
+			goto out;
+		}
+		goto again;
+	}
+
+out:
+	if (info) {
+		if (info->bitmap)
+			kfree(info->bitmap);
+		kfree(info);
+	}
 
 	return ret;
 }
@@ -208,8 +557,8 @@ static int link_free_space(struct btrfs_block_group_cache *block_group,
 int btrfs_add_free_space(struct btrfs_block_group_cache *block_group,
 			 u64 offset, u64 bytes)
 {
-	struct btrfs_free_space *right_info;
-	struct btrfs_free_space *left_info;
+	struct btrfs_free_space *right_info = NULL;
+	struct btrfs_free_space *left_info = NULL;
 	struct btrfs_free_space *info = NULL;
 	int ret = 0;
 
@@ -227,18 +576,38 @@ int btrfs_add_free_space(struct btrfs_block_group_cache *block_group,
 	 * are adding, if there is remove that struct and add a new one to
 	 * cover the entire range
 	 */
-	right_info = tree_search_offset(&block_group->free_space_offset,
-					offset+bytes, 0, 0);
-	left_info = tree_search_offset(&block_group->free_space_offset,
-				       offset-1, 0, 1);
+	right_info = tree_search_offset(block_group, offset + bytes, 0, 0);
+	if (right_info && rb_prev(&right_info->offset_index))
+		left_info = rb_entry(rb_prev(&right_info->offset_index),
+				     struct btrfs_free_space, offset_index);
+	else
+		left_info = tree_search_offset(block_group, offset - 1, 0, 0);
 
-	if (right_info) {
+	/*
+	 * If there was no extent directly to the left or right of this new
+	 * extent then we know we're going to have to allocate a new extent, so
+	 * before we do that see if we need to drop this into a bitmap
+	 */
+	if ((!left_info || left_info->bitmap) &&
+	    (!right_info || right_info->bitmap)) {
+		ret = insert_into_bitmap(block_group, info);
+
+		if (ret < 0) {
+			goto out;
+		} else if (ret) {
+			ret = 0;
+			goto out;
+		}
+	}
+
+	if (right_info && !right_info->bitmap) {
 		unlink_free_space(block_group, right_info);
 		info->bytes += right_info->bytes;
 		kfree(right_info);
 	}
 
-	if (left_info && left_info->offset + left_info->bytes == offset) {
+	if (left_info && !left_info->bitmap &&
+	    left_info->offset + left_info->bytes == offset) {
 		unlink_free_space(block_group, left_info);
 		info->offset = left_info->offset;
 		info->bytes += left_info->bytes;
@@ -248,11 +617,11 @@ int btrfs_add_free_space(struct btrfs_block_group_cache *block_group,
 	ret = link_free_space(block_group, info);
 	if (ret)
 		kfree(info);
-
+out:
 	spin_unlock(&block_group->tree_lock);
 
 	if (ret) {
-		printk(KERN_ERR "btrfs: unable to add free space :%d\n", ret);
+		printk(KERN_CRIT "btrfs: unable to add free space :%d\n", ret);
 		BUG_ON(ret == -EEXIST);
 	}
 
@@ -263,40 +632,65 @@ int btrfs_remove_free_space(struct btrfs_block_group_cache *block_group,
 			    u64 offset, u64 bytes)
 {
 	struct btrfs_free_space *info;
+	struct btrfs_free_space *next_info = NULL;
 	int ret = 0;
 
 	spin_lock(&block_group->tree_lock);
 
-	info = tree_search_offset(&block_group->free_space_offset, offset, 0,
-				  1);
-	if (info && info->offset == offset) {
-		if (info->bytes < bytes) {
-			printk(KERN_ERR "Found free space at %llu, size %llu,"
-			       "trying to use %llu\n",
-			       (unsigned long long)info->offset,
-			       (unsigned long long)info->bytes,
-			       (unsigned long long)bytes);
+again:
+	info = tree_search_offset(block_group, offset, 0, 0);
+	if (!info) {
+		WARN_ON(1);
+		goto out_lock;
+	}
+
+	if (info->bytes < bytes && rb_next(&info->offset_index)) {
+		u64 end;
+		next_info = rb_entry(rb_next(&info->offset_index),
+					     struct btrfs_free_space,
+					     offset_index);
+
+		if (next_info->bitmap)
+			end = next_info->offset + BITS_PER_BITMAP *
+				block_group->sectorsize - 1;
+		else
+			end = next_info->offset + next_info->bytes;
+
+		if (next_info->bytes < bytes ||
+		    next_info->offset > offset || offset > end) {
+			printk(KERN_CRIT "Found free space at %llu, size %llu,"
+			      " trying to use %llu\n",
+			      (unsigned long long)info->offset,
+			      (unsigned long long)info->bytes,
+			      (unsigned long long)bytes);
 			WARN_ON(1);
 			ret = -EINVAL;
-			spin_unlock(&block_group->tree_lock);
-			goto out;
+			goto out_lock;
 		}
-		unlink_free_space(block_group, info);
 
-		if (info->bytes == bytes) {
-			kfree(info);
-			spin_unlock(&block_group->tree_lock);
-			goto out;
+		info = next_info;
+	}
+
+	if (info->bytes == bytes) {
+		unlink_free_space(block_group, info);
+		if (info->bitmap) {
+			kfree(info->bitmap);
+			block_group->total_bitmaps--;
 		}
+		kfree(info);
+		goto out_lock;
+	}
 
+	if (!info->bitmap && info->offset == offset) {
+		unlink_free_space(block_group, info);
 		info->offset += bytes;
 		info->bytes -= bytes;
+		link_free_space(block_group, info);
+		goto out_lock;
+	}
 
-		ret = link_free_space(block_group, info);
-		spin_unlock(&block_group->tree_lock);
-		BUG_ON(ret);
-	} else if (info && info->offset < offset &&
-		   info->offset + info->bytes >= offset + bytes) {
+	if (!info->bitmap && info->offset <= offset &&
+	    info->offset + info->bytes >= offset + bytes) {
 		u64 old_start = info->offset;
 		/*
 		 * we're freeing space in the middle of the info,
@@ -312,7 +706,9 @@ int btrfs_remove_free_space(struct btrfs_block_group_cache *block_group,
 			info->offset = offset + bytes;
 			info->bytes = old_end - info->offset;
 			ret = link_free_space(block_group, info);
-			BUG_ON(ret);
+			WARN_ON(ret);
+			if (ret)
+				goto out_lock;
 		} else {
 			/* the hole we're creating ends at the end
 			 * of the info struct, just free the info
@@ -320,32 +716,22 @@ int btrfs_remove_free_space(struct btrfs_block_group_cache *block_group,
 			kfree(info);
 		}
 		spin_unlock(&block_group->tree_lock);
-		/* step two, insert a new info struct to cover anything
-		 * before the hole
+
+		/* step two, insert a new info struct to cover
+		 * anything before the hole
 		 */
 		ret = btrfs_add_free_space(block_group, old_start,
 					   offset - old_start);
-		BUG_ON(ret);
-	} else {
-		spin_unlock(&block_group->tree_lock);
-		if (!info) {
-			printk(KERN_ERR "couldn't find space %llu to free\n",
-			       (unsigned long long)offset);
-			printk(KERN_ERR "cached is %d, offset %llu bytes %llu\n",
-			       block_group->cached,
-			       (unsigned long long)block_group->key.objectid,
-			       (unsigned long long)block_group->key.offset);
-			btrfs_dump_free_space(block_group, bytes);
-		} else if (info) {
-			printk(KERN_ERR "hmm, found offset=%llu bytes=%llu, "
-			       "but wanted offset=%llu bytes=%llu\n",
-			       (unsigned long long)info->offset,
-			       (unsigned long long)info->bytes,
-			       (unsigned long long)offset,
-			       (unsigned long long)bytes);
-		}
-		WARN_ON(1);
+		WARN_ON(ret);
+		goto out;
 	}
+
+	ret = remove_from_bitmap(block_group, info, &offset, &bytes);
+	if (ret == -EAGAIN)
+		goto again;
+	BUG_ON(ret);
+out_lock:
+	spin_unlock(&block_group->tree_lock);
 out:
 	return ret;
 }
@@ -361,10 +747,13 @@ void btrfs_dump_free_space(struct btrfs_block_group_cache *block_group,
 		info = rb_entry(n, struct btrfs_free_space, offset_index);
 		if (info->bytes >= bytes)
 			count++;
-		printk(KERN_ERR "entry offset %llu, bytes %llu\n",
+		printk(KERN_CRIT "entry offset %llu, bytes %llu, bitmap %s\n",
 		       (unsigned long long)info->offset,
-		       (unsigned long long)info->bytes);
+		       (unsigned long long)info->bytes,
+		       (info->bitmap) ? "yes" : "no");
 	}
+	printk(KERN_INFO "block group has cluster?: %s\n",
+	       list_empty(&block_group->cluster_list) ? "no" : "yes");
 	printk(KERN_INFO "%d blocks of free space at or bigger than bytes is"
 	       "\n", count);
 }
@@ -397,26 +786,35 @@ __btrfs_return_cluster_to_free_space(
 {
 	struct btrfs_free_space *entry;
 	struct rb_node *node;
+	bool bitmap;
 
 	spin_lock(&cluster->lock);
 	if (cluster->block_group != block_group)
 		goto out;
 
+	bitmap = cluster->points_to_bitmap;
+	cluster->block_group = NULL;
 	cluster->window_start = 0;
+	list_del_init(&cluster->block_group_list);
+	cluster->points_to_bitmap = false;
+
+	if (bitmap)
+		goto out;
+
 	node = rb_first(&cluster->root);
-	while(node) {
+	while (node) {
 		entry = rb_entry(node, struct btrfs_free_space, offset_index);
 		node = rb_next(&entry->offset_index);
 		rb_erase(&entry->offset_index, &cluster->root);
-		link_free_space(block_group, entry);
+		BUG_ON(entry->bitmap);
+		tree_insert_offset(&block_group->free_space_offset,
+				   entry->offset, &entry->offset_index, 0);
 	}
-	list_del_init(&cluster->block_group_list);
-
-	btrfs_put_block_group(cluster->block_group);
-	cluster->block_group = NULL;
 	cluster->root.rb_node = NULL;
+
 out:
 	spin_unlock(&cluster->lock);
+	btrfs_put_block_group(block_group);
 	return 0;
 }
 
@@ -425,20 +823,28 @@ void btrfs_remove_free_space_cache(struct btrfs_block_group_cache *block_group)
 	struct btrfs_free_space *info;
 	struct rb_node *node;
 	struct btrfs_free_cluster *cluster;
-	struct btrfs_free_cluster *safe;
+	struct list_head *head;
 
 	spin_lock(&block_group->tree_lock);
-
-	list_for_each_entry_safe(cluster, safe, &block_group->cluster_list,
-				 block_group_list) {
+	while ((head = block_group->cluster_list.next) !=
+	       &block_group->cluster_list) {
+		cluster = list_entry(head, struct btrfs_free_cluster,
+				     block_group_list);
 
 		WARN_ON(cluster->block_group != block_group);
 		__btrfs_return_cluster_to_free_space(block_group, cluster);
+		if (need_resched()) {
+			spin_unlock(&block_group->tree_lock);
+			cond_resched();
+			spin_lock(&block_group->tree_lock);
+		}
 	}
 
-	while ((node = rb_last(&block_group->free_space_bytes)) != NULL) {
-		info = rb_entry(node, struct btrfs_free_space, bytes_index);
+	while ((node = rb_last(&block_group->free_space_offset)) != NULL) {
+		info = rb_entry(node, struct btrfs_free_space, offset_index);
 		unlink_free_space(block_group, info);
+		if (info->bitmap)
+			kfree(info->bitmap);
 		kfree(info);
 		if (need_resched()) {
 			spin_unlock(&block_group->tree_lock);
@@ -446,6 +852,7 @@ void btrfs_remove_free_space_cache(struct btrfs_block_group_cache *block_group)
 			spin_lock(&block_group->tree_lock);
 		}
 	}
+
 	spin_unlock(&block_group->tree_lock);
 }
 
@@ -453,27 +860,37 @@ u64 btrfs_find_space_for_alloc(struct btrfs_block_group_cache *block_group,
 			       u64 offset, u64 bytes, u64 empty_size)
 {
 	struct btrfs_free_space *entry = NULL;
+	u64 bytes_search = bytes + empty_size;
 	u64 ret = 0;
 
 	spin_lock(&block_group->tree_lock);
-	entry = tree_search_offset(&block_group->free_space_offset, offset,
-				   bytes + empty_size, 1);
+	entry = find_free_space(block_group, &offset, &bytes_search, 0);
 	if (!entry)
-		entry = tree_search_bytes(&block_group->free_space_bytes,
-					  offset, bytes + empty_size);
-	if (entry) {
+		goto out;
+
+	ret = offset;
+	if (entry->bitmap) {
+		bitmap_clear_bits(entry, offset, bytes,
+				  block_group->sectorsize);
+		if (!entry->bytes) {
+			unlink_free_space(block_group, entry);
+			kfree(entry->bitmap);
+			kfree(entry);
+			block_group->total_bitmaps--;
+			recalculate_thresholds(block_group);
+		}
+	} else {
 		unlink_free_space(block_group, entry);
-		ret = entry->offset;
 		entry->offset += bytes;
 		entry->bytes -= bytes;
-
 		if (!entry->bytes)
 			kfree(entry);
 		else
 			link_free_space(block_group, entry);
 	}
-	spin_unlock(&block_group->tree_lock);
 
+out:
+	spin_unlock(&block_group->tree_lock);
 	return ret;
 }
 
@@ -517,6 +934,47 @@ int btrfs_return_cluster_to_free_space(
 	return ret;
 }
 
+static u64 btrfs_alloc_from_bitmap(struct btrfs_block_group_cache *block_group,
+				   struct btrfs_free_cluster *cluster,
+				   u64 bytes, u64 min_start)
+{
+	struct btrfs_free_space *entry;
+	int err;
+	u64 search_start = cluster->window_start;
+	u64 search_bytes = bytes;
+	u64 ret = 0;
+
+	spin_lock(&block_group->tree_lock);
+	spin_lock(&cluster->lock);
+
+	if (!cluster->points_to_bitmap)
+		goto out;
+
+	if (cluster->block_group != block_group)
+		goto out;
+
+	entry = tree_search_offset(block_group, search_start, 0, 0);
+
+	if (!entry || !entry->bitmap)
+		goto out;
+
+	search_start = min_start;
+	search_bytes = bytes;
+
+	err = search_bitmap(block_group, entry, &search_start,
+			    &search_bytes);
+	if (err)
+		goto out;
+
+	ret = search_start;
+	bitmap_clear_bits(entry, ret, bytes, block_group->sectorsize);
+out:
+	spin_unlock(&cluster->lock);
+	spin_unlock(&block_group->tree_lock);
+
+	return ret;
+}
+
 /*
  * given a cluster, try to allocate 'bytes' from it, returns 0
  * if it couldn't find anything suitably large, or a logical disk offset
@@ -530,6 +988,10 @@ u64 btrfs_alloc_from_cluster(struct btrfs_block_group_cache *block_group,
 	struct rb_node *node;
 	u64 ret = 0;
 
+	if (cluster->points_to_bitmap)
+		return btrfs_alloc_from_bitmap(block_group, cluster, bytes,
+					       min_start);
+
 	spin_lock(&cluster->lock);
 	if (bytes > cluster->max_size)
 		goto out;
@@ -567,9 +1029,73 @@ u64 btrfs_alloc_from_cluster(struct btrfs_block_group_cache *block_group,
 	}
 out:
 	spin_unlock(&cluster->lock);
+
 	return ret;
 }
 
+static int btrfs_bitmap_cluster(struct btrfs_block_group_cache *block_group,
+				struct btrfs_free_space *entry,
+				struct btrfs_free_cluster *cluster,
+				u64 offset, u64 bytes, u64 min_bytes)
+{
+	unsigned long next_zero;
+	unsigned long i;
+	unsigned long search_bits;
+	unsigned long total_bits;
+	unsigned long found_bits;
+	unsigned long start = 0;
+	unsigned long total_found = 0;
+	bool found = false;
+
+	i = offset_to_bit(entry->offset, block_group->sectorsize,
+			  max_t(u64, offset, entry->offset));
+	search_bits = bytes_to_bits(min_bytes, block_group->sectorsize);
+	total_bits = bytes_to_bits(bytes, block_group->sectorsize);
+
+again:
+	found_bits = 0;
+	for (i = find_next_bit(entry->bitmap, BITS_PER_BITMAP, i);
+	     i < BITS_PER_BITMAP;
+	     i = find_next_bit(entry->bitmap, BITS_PER_BITMAP, i + 1)) {
+		next_zero = find_next_zero_bit(entry->bitmap,
+					       BITS_PER_BITMAP, i);
+		if (next_zero - i >= search_bits) {
+			found_bits = next_zero - i;
+			break;
+		}
+		i = next_zero;
+	}
+
+	if (!found_bits)
+		return -1;
+
+	if (!found) {
+		start = i;
+		found = true;
+	}
+
+	total_found += found_bits;
+
+	if (cluster->max_size < found_bits * block_group->sectorsize)
+		cluster->max_size = found_bits * block_group->sectorsize;
+
+	if (total_found < total_bits) {
+		i = find_next_bit(entry->bitmap, BITS_PER_BITMAP, next_zero);
+		if (i - start > total_bits * 2) {
+			total_found = 0;
+			cluster->max_size = 0;
+			found = false;
+		}
+		goto again;
+	}
+
+	cluster->window_start = start * block_group->sectorsize +
+		entry->offset;
+	cluster->points_to_bitmap = true;
+
+	return 0;
+}
+
 /*
  * here we try to find a cluster of blocks in a block group.  The goal
  * is to find at least bytes free and up to empty_size + bytes free.
@@ -587,12 +1113,12 @@ int btrfs_find_space_cluster(struct btrfs_trans_handle *trans,
 	struct btrfs_free_space *entry = NULL;
 	struct rb_node *node;
 	struct btrfs_free_space *next;
-	struct btrfs_free_space *last;
+	struct btrfs_free_space *last = NULL;
 	u64 min_bytes;
 	u64 window_start;
 	u64 window_free;
 	u64 max_extent = 0;
-	int total_retries = 0;
+	bool found_bitmap = false;
 	int ret;
 
 	/* for metadata, allow allocates with more holes */
@@ -620,30 +1146,79 @@ int btrfs_find_space_cluster(struct btrfs_trans_handle *trans,
 		goto out;
 	}
 again:
-	min_bytes = min(min_bytes, bytes + empty_size);
-	entry = tree_search_bytes(&block_group->free_space_bytes,
-				  offset, min_bytes);
+	entry = tree_search_offset(block_group, offset, found_bitmap, 1);
 	if (!entry) {
 		ret = -ENOSPC;
 		goto out;
 	}
+
+	/*
+	 * If found_bitmap is true, we exhausted our search for extent entries,
+	 * and we just want to search all of the bitmaps that we can find, and
+	 * ignore any extent entries we find.
+	 */
+	while (entry->bitmap || found_bitmap ||
+	       (!entry->bitmap && entry->bytes < min_bytes)) {
+		struct rb_node *node = rb_next(&entry->offset_index);
+
+		if (entry->bitmap && entry->bytes > bytes + empty_size) {
+			ret = btrfs_bitmap_cluster(block_group, entry, cluster,
+						   offset, bytes + empty_size,
+						   min_bytes);
+			if (!ret)
+				goto got_it;
+		}
+
+		if (!node) {
+			ret = -ENOSPC;
+			goto out;
+		}
+		entry = rb_entry(node, struct btrfs_free_space, offset_index);
+	}
+
+	/*
+	 * We already searched all the extent entries from the passed in offset
+	 * to the end and didn't find enough space for the cluster, and we also
+	 * didn't find any bitmaps that met our criteria, just go ahead and exit
+	 */
+	if (found_bitmap) {
+		ret = -ENOSPC;
+		goto out;
+	}
+
+	cluster->points_to_bitmap = false;
 	window_start = entry->offset;
 	window_free = entry->bytes;
 	last = entry;
 	max_extent = entry->bytes;
 
-	while(1) {
+	while (1) {
 		/* out window is just right, lets fill it */
 		if (window_free >= bytes + empty_size)
 			break;
 
 		node = rb_next(&last->offset_index);
 		if (!node) {
+			if (found_bitmap)
+				goto again;
 			ret = -ENOSPC;
 			goto out;
 		}
 		next = rb_entry(node, struct btrfs_free_space, offset_index);
 
+		/*
+		 * we found a bitmap, so if this search doesn't result in a
+		 * cluster, we know to go and search again for the bitmaps and
+		 * start looking for space there
+		 */
+		if (next->bitmap) {
+			if (!found_bitmap)
+				offset = next->offset;
+			found_bitmap = true;
+			last = next;
+			continue;
+		}
+
 		/*
 		 * we haven't filled the empty size and the window is
 		 * very large.  reset and try again
@@ -655,19 +1230,6 @@ again:
 			window_free = entry->bytes;
 			last = entry;
 			max_extent = 0;
-			total_retries++;
-			if (total_retries % 64 == 0) {
-				if (min_bytes >= (bytes + empty_size)) {
-					ret = -ENOSPC;
-					goto out;
-				}
-				/*
-				 * grow our allocation a bit, we're not having
-				 * much luck
-				 */
-				min_bytes *= 2;
-				goto again;
-			}
 		} else {
 			last = next;
 			window_free += next->bytes;
@@ -685,11 +1247,19 @@ again:
 	 * The cluster includes an rbtree, but only uses the offset index
 	 * of each free space cache entry.
 	 */
-	while(1) {
+	while (1) {
 		node = rb_next(&entry->offset_index);
-		unlink_free_space(block_group, entry);
+		if (entry->bitmap && node) {
+			entry = rb_entry(node, struct btrfs_free_space,
+					 offset_index);
+			continue;
+		} else if (entry->bitmap && !node) {
+			break;
+		}
+
+		rb_erase(&entry->offset_index, &block_group->free_space_offset);
 		ret = tree_insert_offset(&cluster->root, entry->offset,
-					 &entry->offset_index);
+					 &entry->offset_index, 0);
 		BUG_ON(ret);
 
 		if (!node || entry == last)
@@ -697,8 +1267,10 @@ again:
 
 		entry = rb_entry(node, struct btrfs_free_space, offset_index);
 	}
-	ret = 0;
+
 	cluster->max_size = max_extent;
+got_it:
+	ret = 0;
 	atomic_inc(&block_group->count);
 	list_add_tail(&cluster->block_group_list, &block_group->cluster_list);
 	cluster->block_group = block_group;
@@ -718,6 +1290,7 @@ void btrfs_init_free_cluster(struct btrfs_free_cluster *cluster)
 	spin_lock_init(&cluster->refill_lock);
 	cluster->root.rb_node = NULL;
 	cluster->max_size = 0;
+	cluster->points_to_bitmap = false;
 	INIT_LIST_HEAD(&cluster->block_group_list);
 	cluster->block_group = NULL;
 }
diff --git a/fs/btrfs/free-space-cache.h b/fs/btrfs/free-space-cache.h
index 266fb876405..890a8e79011 100644
--- a/fs/btrfs/free-space-cache.h
+++ b/fs/btrfs/free-space-cache.h
@@ -19,6 +19,14 @@
 #ifndef __BTRFS_FREE_SPACE_CACHE
 #define __BTRFS_FREE_SPACE_CACHE
 
+struct btrfs_free_space {
+	struct rb_node offset_index;
+	u64 offset;
+	u64 bytes;
+	unsigned long *bitmap;
+	struct list_head list;
+};
+
 int btrfs_add_free_space(struct btrfs_block_group_cache *block_group,
 			 u64 bytenr, u64 size);
 int btrfs_remove_free_space(struct btrfs_block_group_cache *block_group,
-- 
GitLab


From 817d52f8dba26d0295c26035531c30ce5f1e3c3e Mon Sep 17 00:00:00 2001
From: Josef Bacik <josef@redhat.com>
Date: Mon, 13 Jul 2009 21:29:25 -0400
Subject: [PATCH 0084/1153] Btrfs: async block group caching

This patch moves the caching of the block group off to a kthread in order to
allow people to allocate sooner.  Instead of blocking up behind the caching
mutex, we instead kick of the caching kthread, and then attempt to make an
allocation.  If we cannot, we wait on the block groups caching waitqueue, which
the caching kthread will wake the waiting threads up everytime it finds 2 meg
worth of space, and then again when its finished caching.  This is how I tested
the speedup from this

mkfs the disk
mount the disk
fill the disk up with fs_mark
unmount the disk
mount the disk
time touch /mnt/foo

Without my changes this took 11 seconds on my box, with these changes it now
takes 1 second.

Another change thats been put in place is we lock the super mirror's in the
pinned extent map in order to keep us from adding that stuff as free space when
caching the block group.  This doesn't really change anything else as far as the
pinned extent map is concerned, since for actual pinned extents we use
EXTENT_DIRTY, but it does mean that when we unmount we have to go in and unlock
those extents to keep from leaking memory.

I've also added a check where when we are reading block groups from disk, if the
amount of space used == the size of the block group, we go ahead and mark the
block group as cached.  This drastically reduces the amount of time it takes to
cache the block groups.  Using the same test as above, except doing a dd to a
file and then unmounting, it used to take 33 seconds to umount, now it takes 3
seconds.

This version uses the commit_root in the caching kthread, and then keeps track
of how many async caching threads are running at any given time so if one of the
async threads is still running as we cross transactions we can wait until its
finished before handling the pinned extents.  Thank you,

Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/ctree.h            |  22 +-
 fs/btrfs/disk-io.c          |   3 +
 fs/btrfs/extent-tree.c      | 471 +++++++++++++++++++++++++++++-------
 fs/btrfs/free-space-cache.c |  42 ++--
 fs/btrfs/transaction.c      |  23 +-
 fs/btrfs/tree-log.c         |   2 +-
 6 files changed, 439 insertions(+), 124 deletions(-)

diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h
index 0cbf3491bb7..42b03c4ee49 100644
--- a/fs/btrfs/ctree.h
+++ b/fs/btrfs/ctree.h
@@ -691,6 +691,7 @@ struct btrfs_space_info {
 	struct list_head block_groups;
 	spinlock_t lock;
 	struct rw_semaphore groups_sem;
+	atomic_t caching_threads;
 };
 
 /*
@@ -721,11 +722,17 @@ struct btrfs_free_cluster {
 	struct list_head block_group_list;
 };
 
+enum btrfs_caching_type {
+	BTRFS_CACHE_NO		= 0,
+	BTRFS_CACHE_STARTED	= 1,
+	BTRFS_CACHE_FINISHED	= 2,
+};
+
 struct btrfs_block_group_cache {
 	struct btrfs_key key;
 	struct btrfs_block_group_item item;
+	struct btrfs_fs_info *fs_info;
 	spinlock_t lock;
-	struct mutex cache_mutex;
 	u64 pinned;
 	u64 reserved;
 	u64 flags;
@@ -733,15 +740,19 @@ struct btrfs_block_group_cache {
 	int extents_thresh;
 	int free_extents;
 	int total_bitmaps;
-	int cached;
 	int ro;
 	int dirty;
 
+	/* cache tracking stuff */
+	wait_queue_head_t caching_q;
+	int cached;
+
 	struct btrfs_space_info *space_info;
 
 	/* free space cache stuff */
 	spinlock_t tree_lock;
 	struct rb_root free_space_offset;
+	u64 free_space;
 
 	/* block group cache stuff */
 	struct rb_node cache_node;
@@ -834,6 +845,7 @@ struct btrfs_fs_info {
 	atomic_t async_submit_draining;
 	atomic_t nr_async_bios;
 	atomic_t async_delalloc_pages;
+	atomic_t async_caching_threads;
 
 	/*
 	 * this is used by the balancing code to wait for all the pending
@@ -950,6 +962,9 @@ struct btrfs_root {
 	/* the node lock is held while changing the node pointer */
 	spinlock_t node_lock;
 
+	/* taken when updating the commit root */
+	struct rw_semaphore commit_root_sem;
+
 	struct extent_buffer *commit_root;
 	struct btrfs_root *log_root;
 	struct btrfs_root *reloc_root;
@@ -1911,7 +1926,7 @@ int btrfs_run_delayed_refs(struct btrfs_trans_handle *trans,
 			   struct btrfs_root *root, unsigned long count);
 int btrfs_lookup_extent(struct btrfs_root *root, u64 start, u64 len);
 int btrfs_update_pinned_extents(struct btrfs_root *root,
-				u64 bytenr, u64 num, int pin);
+				u64 bytenr, u64 num, int pin, int mark_free);
 int btrfs_drop_leaf_ref(struct btrfs_trans_handle *trans,
 			struct btrfs_root *root, struct extent_buffer *leaf);
 int btrfs_cross_ref_exist(struct btrfs_trans_handle *trans,
@@ -1996,6 +2011,7 @@ void btrfs_delalloc_reserve_space(struct btrfs_root *root, struct inode *inode,
 				 u64 bytes);
 void btrfs_delalloc_free_space(struct btrfs_root *root, struct inode *inode,
 			      u64 bytes);
+void btrfs_free_super_mirror_extents(struct btrfs_fs_info *info);
 /* ctree.c */
 int btrfs_bin_search(struct extent_buffer *eb, struct btrfs_key *key,
 		     int level, int *slot);
diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c
index 55d9d188e69..ec2c915f7f4 100644
--- a/fs/btrfs/disk-io.c
+++ b/fs/btrfs/disk-io.c
@@ -907,6 +907,7 @@ static int __setup_root(u32 nodesize, u32 leafsize, u32 sectorsize,
 	spin_lock_init(&root->inode_lock);
 	mutex_init(&root->objectid_mutex);
 	mutex_init(&root->log_mutex);
+	init_rwsem(&root->commit_root_sem);
 	init_waitqueue_head(&root->log_writer_wait);
 	init_waitqueue_head(&root->log_commit_wait[0]);
 	init_waitqueue_head(&root->log_commit_wait[1]);
@@ -1566,6 +1567,7 @@ struct btrfs_root *open_ctree(struct super_block *sb,
 	atomic_set(&fs_info->async_delalloc_pages, 0);
 	atomic_set(&fs_info->async_submit_draining, 0);
 	atomic_set(&fs_info->nr_async_bios, 0);
+	atomic_set(&fs_info->async_caching_threads, 0);
 	fs_info->sb = sb;
 	fs_info->max_extent = (u64)-1;
 	fs_info->max_inline = 8192 * 1024;
@@ -2337,6 +2339,7 @@ int close_ctree(struct btrfs_root *root)
 	free_extent_buffer(root->fs_info->csum_root->commit_root);
 
 	btrfs_free_block_groups(root->fs_info);
+	btrfs_free_super_mirror_extents(root->fs_info);
 
 	del_fs_roots(fs_info);
 
diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index 98697be6bdd..9a489cc89fd 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -21,6 +21,7 @@
 #include <linux/blkdev.h>
 #include <linux/sort.h>
 #include <linux/rcupdate.h>
+#include <linux/kthread.h>
 #include "compat.h"
 #include "hash.h"
 #include "ctree.h"
@@ -61,6 +62,13 @@ static int do_chunk_alloc(struct btrfs_trans_handle *trans,
 			  struct btrfs_root *extent_root, u64 alloc_bytes,
 			  u64 flags, int force);
 
+static noinline int
+block_group_cache_done(struct btrfs_block_group_cache *cache)
+{
+	smp_mb();
+	return cache->cached == BTRFS_CACHE_FINISHED;
+}
+
 static int block_group_bits(struct btrfs_block_group_cache *cache, u64 bits)
 {
 	return (cache->flags & bits) == bits;
@@ -145,21 +153,64 @@ block_group_cache_tree_search(struct btrfs_fs_info *info, u64 bytenr,
 	return ret;
 }
 
+void btrfs_free_super_mirror_extents(struct btrfs_fs_info *info)
+{
+	u64 start, end, last = 0;
+	int ret;
+
+	while (1) {
+		ret = find_first_extent_bit(&info->pinned_extents, last,
+					    &start, &end, EXTENT_LOCKED);
+		if (ret)
+			break;
+
+		unlock_extent(&info->pinned_extents, start, end, GFP_NOFS);
+		last = end+1;
+	}
+}
+
+static int remove_sb_from_cache(struct btrfs_root *root,
+				struct btrfs_block_group_cache *cache)
+{
+	struct btrfs_fs_info *fs_info = root->fs_info;
+	u64 bytenr;
+	u64 *logical;
+	int stripe_len;
+	int i, nr, ret;
+
+	for (i = 0; i < BTRFS_SUPER_MIRROR_MAX; i++) {
+		bytenr = btrfs_sb_offset(i);
+		ret = btrfs_rmap_block(&root->fs_info->mapping_tree,
+				       cache->key.objectid, bytenr,
+				       0, &logical, &nr, &stripe_len);
+		BUG_ON(ret);
+		while (nr--) {
+			try_lock_extent(&fs_info->pinned_extents,
+					logical[nr],
+					logical[nr] + stripe_len - 1, GFP_NOFS);
+		}
+		kfree(logical);
+	}
+
+	return 0;
+}
+
 /*
  * this is only called by cache_block_group, since we could have freed extents
  * we need to check the pinned_extents for any extents that can't be used yet
  * since their free space will be released as soon as the transaction commits.
  */
-static int add_new_free_space(struct btrfs_block_group_cache *block_group,
+static u64 add_new_free_space(struct btrfs_block_group_cache *block_group,
 			      struct btrfs_fs_info *info, u64 start, u64 end)
 {
-	u64 extent_start, extent_end, size;
+	u64 extent_start, extent_end, size, total_added = 0;
 	int ret;
 
 	while (start < end) {
 		ret = find_first_extent_bit(&info->pinned_extents, start,
 					    &extent_start, &extent_end,
-					    EXTENT_DIRTY);
+					    EXTENT_DIRTY|EXTENT_LOCKED|
+					    EXTENT_DELALLOC);
 		if (ret)
 			break;
 
@@ -167,6 +218,7 @@ static int add_new_free_space(struct btrfs_block_group_cache *block_group,
 			start = extent_end + 1;
 		} else if (extent_start > start && extent_start < end) {
 			size = extent_start - start;
+			total_added += size;
 			ret = btrfs_add_free_space(block_group, start,
 						   size);
 			BUG_ON(ret);
@@ -178,84 +230,139 @@ static int add_new_free_space(struct btrfs_block_group_cache *block_group,
 
 	if (start < end) {
 		size = end - start;
+		total_added += size;
 		ret = btrfs_add_free_space(block_group, start, size);
 		BUG_ON(ret);
 	}
 
-	return 0;
+	return total_added;
 }
 
-static int remove_sb_from_cache(struct btrfs_root *root,
-				struct btrfs_block_group_cache *cache)
+DEFINE_MUTEX(discard_mutex);
+
+/*
+ * if async kthreads are running when we cross transactions, we mark any pinned
+ * extents with EXTENT_DELALLOC and then let the caching kthreads clean up those
+ * extents when they are done.  Also we run this from btrfs_finish_extent_commit
+ * in case there were some pinned extents that were missed because we had
+ * already cached that block group.
+ */
+static void btrfs_discard_pinned_extents(struct btrfs_fs_info *fs_info,
+					 struct btrfs_block_group_cache *cache)
 {
-	u64 bytenr;
-	u64 *logical;
-	int stripe_len;
-	int i, nr, ret;
+	u64 start, end, last;
+	int ret;
 
-	for (i = 0; i < BTRFS_SUPER_MIRROR_MAX; i++) {
-		bytenr = btrfs_sb_offset(i);
-		ret = btrfs_rmap_block(&root->fs_info->mapping_tree,
-				       cache->key.objectid, bytenr, 0,
-				       &logical, &nr, &stripe_len);
-		BUG_ON(ret);
-		while (nr--) {
-			btrfs_remove_free_space(cache, logical[nr],
-						stripe_len);
+	if (!cache)
+		last = 0;
+	else
+		last = cache->key.objectid;
+
+	mutex_lock(&discard_mutex);
+	while (1) {
+		ret = find_first_extent_bit(&fs_info->pinned_extents, last,
+					    &start, &end, EXTENT_DELALLOC);
+		if (ret)
+			break;
+
+		if (cache && start >= cache->key.objectid + cache->key.offset)
+			break;
+
+
+		if (!cache) {
+			cache = btrfs_lookup_block_group(fs_info, start);
+			BUG_ON(!cache);
+
+			start = max(start, cache->key.objectid);
+			end = min(end, cache->key.objectid + cache->key.offset - 1);
+
+			if (block_group_cache_done(cache))
+				btrfs_add_free_space(cache, start,
+						     end - start + 1);
+			cache = NULL;
+		} else {
+			start = max(start, cache->key.objectid);
+			end = min(end, cache->key.objectid + cache->key.offset - 1);
+			btrfs_add_free_space(cache, start, end - start + 1);
+		}
+
+		clear_extent_bits(&fs_info->pinned_extents, start, end,
+				  EXTENT_DELALLOC, GFP_NOFS);
+		last = end + 1;
+
+		if (need_resched()) {
+			mutex_unlock(&discard_mutex);
+			cond_resched();
+			mutex_lock(&discard_mutex);
 		}
-		kfree(logical);
 	}
-	return 0;
+	mutex_unlock(&discard_mutex);
 }
 
-static int cache_block_group(struct btrfs_root *root,
-			     struct btrfs_block_group_cache *block_group)
+static int caching_kthread(void *data)
 {
+	struct btrfs_block_group_cache *block_group = data;
+	struct btrfs_fs_info *fs_info = block_group->fs_info;
+	u64 last = 0;
 	struct btrfs_path *path;
 	int ret = 0;
 	struct btrfs_key key;
 	struct extent_buffer *leaf;
 	int slot;
-	u64 last;
-
-	if (!block_group)
-		return 0;
+	u64 total_found = 0;
 
-	root = root->fs_info->extent_root;
-
-	if (block_group->cached)
-		return 0;
+	BUG_ON(!fs_info);
 
 	path = btrfs_alloc_path();
 	if (!path)
 		return -ENOMEM;
 
-	path->reada = 2;
+	atomic_inc(&fs_info->async_caching_threads);
+	atomic_inc(&block_group->space_info->caching_threads);
+	last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET);
+again:
+	/* need to make sure the commit_root doesn't disappear */
+	down_read(&fs_info->extent_root->commit_root_sem);
+
 	/*
-	 * we get into deadlocks with paths held by callers of this function.
-	 * since the alloc_mutex is protecting things right now, just
-	 * skip the locking here
+	 * We don't want to deadlock with somebody trying to allocate a new
+	 * extent for the extent root while also trying to search the extent
+	 * root to add free space.  So we skip locking and search the commit
+	 * root, since its read-only
 	 */
 	path->skip_locking = 1;
-	last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET);
+	path->search_commit_root = 1;
+	path->reada = 2;
+
 	key.objectid = last;
 	key.offset = 0;
 	btrfs_set_key_type(&key, BTRFS_EXTENT_ITEM_KEY);
-	ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
+	ret = btrfs_search_slot(NULL, fs_info->extent_root, &key, path, 0, 0);
 	if (ret < 0)
 		goto err;
 
 	while (1) {
+		smp_mb();
+		if (block_group->fs_info->closing)
+			break;
+
 		leaf = path->nodes[0];
 		slot = path->slots[0];
 		if (slot >= btrfs_header_nritems(leaf)) {
-			ret = btrfs_next_leaf(root, path);
+			ret = btrfs_next_leaf(fs_info->extent_root, path);
 			if (ret < 0)
 				goto err;
-			if (ret == 0)
-				continue;
-			else
+			else if (ret)
 				break;
+
+			if (need_resched()) {
+				btrfs_release_path(fs_info->extent_root, path);
+				up_read(&fs_info->extent_root->commit_root_sem);
+				cond_resched();
+				goto again;
+			}
+
+			continue;
 		}
 		btrfs_item_key_to_cpu(leaf, &key, slot);
 		if (key.objectid < block_group->key.objectid)
@@ -266,24 +373,63 @@ static int cache_block_group(struct btrfs_root *root,
 			break;
 
 		if (btrfs_key_type(&key) == BTRFS_EXTENT_ITEM_KEY) {
-			add_new_free_space(block_group, root->fs_info, last,
-					   key.objectid);
-
+			total_found += add_new_free_space(block_group,
+							  fs_info, last,
+							  key.objectid);
 			last = key.objectid + key.offset;
 		}
+
+		if (total_found > (1024 * 1024 * 2)) {
+			total_found = 0;
+			wake_up(&block_group->caching_q);
+		}
 next:
 		path->slots[0]++;
 	}
+	ret = 0;
 
-	add_new_free_space(block_group, root->fs_info, last,
-			   block_group->key.objectid +
-			   block_group->key.offset);
+	total_found += add_new_free_space(block_group, fs_info, last,
+					  block_group->key.objectid +
+					  block_group->key.offset);
+
+	spin_lock(&block_group->lock);
+	block_group->cached = BTRFS_CACHE_FINISHED;
+	spin_unlock(&block_group->lock);
 
-	block_group->cached = 1;
-	remove_sb_from_cache(root, block_group);
-	ret = 0;
 err:
 	btrfs_free_path(path);
+	up_read(&fs_info->extent_root->commit_root_sem);
+	atomic_dec(&fs_info->async_caching_threads);
+	atomic_dec(&block_group->space_info->caching_threads);
+	wake_up(&block_group->caching_q);
+
+	if (!ret)
+		btrfs_discard_pinned_extents(fs_info, block_group);
+
+	return 0;
+}
+
+static int cache_block_group(struct btrfs_block_group_cache *cache)
+{
+	struct task_struct *tsk;
+	int ret = 0;
+
+	spin_lock(&cache->lock);
+	if (cache->cached != BTRFS_CACHE_NO) {
+		spin_unlock(&cache->lock);
+		return ret;
+	}
+	cache->cached = BTRFS_CACHE_STARTED;
+	spin_unlock(&cache->lock);
+
+	tsk = kthread_run(caching_kthread, cache, "btrfs-cache-%llu\n",
+			  cache->key.objectid);
+	if (IS_ERR(tsk)) {
+		ret = PTR_ERR(tsk);
+		printk(KERN_ERR "error running thread %d\n", ret);
+		BUG();
+	}
+
 	return ret;
 }
 
@@ -1721,7 +1867,7 @@ static int run_one_delayed_ref(struct btrfs_trans_handle *trans,
 				BUG_ON(ret);
 			}
 			btrfs_update_pinned_extents(root, node->bytenr,
-						    node->num_bytes, 1);
+						    node->num_bytes, 1, 0);
 			update_reserved_extents(root, node->bytenr,
 						node->num_bytes, 0);
 		}
@@ -2496,6 +2642,7 @@ static int update_space_info(struct btrfs_fs_info *info, u64 flags,
 	found->force_alloc = 0;
 	*space_info = found;
 	list_add_rcu(&found->list, &info->space_info);
+	atomic_set(&found->caching_threads, 0);
 	return 0;
 }
 
@@ -2953,7 +3100,7 @@ static u64 first_logical_byte(struct btrfs_root *root, u64 search_start)
 }
 
 int btrfs_update_pinned_extents(struct btrfs_root *root,
-				u64 bytenr, u64 num, int pin)
+				u64 bytenr, u64 num, int pin, int mark_free)
 {
 	u64 len;
 	struct btrfs_block_group_cache *cache;
@@ -2988,7 +3135,7 @@ int btrfs_update_pinned_extents(struct btrfs_root *root,
 			spin_unlock(&cache->lock);
 			spin_unlock(&cache->space_info->lock);
 			fs_info->total_pinned -= len;
-			if (cache->cached)
+			if (block_group_cache_done(cache) && mark_free)
 				btrfs_add_free_space(cache, bytenr, len);
 		}
 		btrfs_put_block_group(cache);
@@ -3034,14 +3181,27 @@ int btrfs_copy_pinned(struct btrfs_root *root, struct extent_io_tree *copy)
 	u64 last = 0;
 	u64 start;
 	u64 end;
+	bool caching_kthreads = false;
 	struct extent_io_tree *pinned_extents = &root->fs_info->pinned_extents;
 	int ret;
 
+	if (atomic_read(&root->fs_info->async_caching_threads))
+		caching_kthreads = true;
+
 	while (1) {
 		ret = find_first_extent_bit(pinned_extents, last,
 					    &start, &end, EXTENT_DIRTY);
 		if (ret)
 			break;
+
+		/*
+		 * we need to make sure that the pinned extents don't go away
+		 * while we are caching block groups
+		 */
+		if (unlikely(caching_kthreads))
+			set_extent_delalloc(pinned_extents, start, end,
+					    GFP_NOFS);
+
 		set_extent_dirty(copy, start, end, GFP_NOFS);
 		last = end + 1;
 	}
@@ -3055,6 +3215,12 @@ int btrfs_finish_extent_commit(struct btrfs_trans_handle *trans,
 	u64 start;
 	u64 end;
 	int ret;
+	int mark_free = 1;
+
+	ret = find_first_extent_bit(&root->fs_info->pinned_extents, 0,
+				    &start, &end, EXTENT_DELALLOC);
+	if (!ret)
+		mark_free = 0;
 
 	while (1) {
 		ret = find_first_extent_bit(unpin, 0, &start, &end,
@@ -3065,11 +3231,16 @@ int btrfs_finish_extent_commit(struct btrfs_trans_handle *trans,
 		ret = btrfs_discard_extent(root, start, end + 1 - start);
 
 		/* unlocks the pinned mutex */
-		btrfs_update_pinned_extents(root, start, end + 1 - start, 0);
+		btrfs_update_pinned_extents(root, start, end + 1 - start, 0,
+					    mark_free);
 		clear_extent_dirty(unpin, start, end, GFP_NOFS);
 
 		cond_resched();
 	}
+
+	if (unlikely(!mark_free))
+		btrfs_discard_pinned_extents(root->fs_info, NULL);
+
 	return ret;
 }
 
@@ -3110,7 +3281,7 @@ static int pin_down_bytes(struct btrfs_trans_handle *trans,
 pinit:
 	btrfs_set_path_blocking(path);
 	/* unlocks the pinned mutex */
-	btrfs_update_pinned_extents(root, bytenr, num_bytes, 1);
+	btrfs_update_pinned_extents(root, bytenr, num_bytes, 1, 0);
 
 	BUG_ON(err < 0);
 	return 0;
@@ -3421,7 +3592,7 @@ int btrfs_free_extent(struct btrfs_trans_handle *trans,
 	if (root_objectid == BTRFS_TREE_LOG_OBJECTID) {
 		WARN_ON(owner >= BTRFS_FIRST_FREE_OBJECTID);
 		/* unlocks the pinned mutex */
-		btrfs_update_pinned_extents(root, bytenr, num_bytes, 1);
+		btrfs_update_pinned_extents(root, bytenr, num_bytes, 1, 0);
 		update_reserved_extents(root, bytenr, num_bytes, 0);
 		ret = 0;
 	} else if (owner < BTRFS_FIRST_FREE_OBJECTID) {
@@ -3447,6 +3618,45 @@ static u64 stripe_align(struct btrfs_root *root, u64 val)
 	return ret;
 }
 
+/*
+ * when we wait for progress in the block group caching, its because
+ * our allocation attempt failed at least once.  So, we must sleep
+ * and let some progress happen before we try again.
+ *
+ * This function will sleep at least once waiting for new free space to
+ * show up, and then it will check the block group free space numbers
+ * for our min num_bytes.  Another option is to have it go ahead
+ * and look in the rbtree for a free extent of a given size, but this
+ * is a good start.
+ */
+static noinline int
+wait_block_group_cache_progress(struct btrfs_block_group_cache *cache,
+				u64 num_bytes)
+{
+	DEFINE_WAIT(wait);
+
+	prepare_to_wait(&cache->caching_q, &wait, TASK_UNINTERRUPTIBLE);
+
+	if (block_group_cache_done(cache)) {
+		finish_wait(&cache->caching_q, &wait);
+		return 0;
+	}
+	schedule();
+	finish_wait(&cache->caching_q, &wait);
+
+	wait_event(cache->caching_q, block_group_cache_done(cache) ||
+		   (cache->free_space >= num_bytes));
+	return 0;
+}
+
+enum btrfs_loop_type {
+	LOOP_CACHED_ONLY = 0,
+	LOOP_CACHING_NOWAIT = 1,
+	LOOP_CACHING_WAIT = 2,
+	LOOP_ALLOC_CHUNK = 3,
+	LOOP_NO_EMPTY_SIZE = 4,
+};
+
 /*
  * walks the btree of allocated extents and find a hole of a given size.
  * The key ins is changed to record the hole:
@@ -3472,6 +3682,7 @@ static noinline int find_free_extent(struct btrfs_trans_handle *trans,
 	struct btrfs_space_info *space_info;
 	int last_ptr_loop = 0;
 	int loop = 0;
+	bool found_uncached_bg = false;
 
 	WARN_ON(num_bytes < root->sectorsize);
 	btrfs_set_key_type(ins, BTRFS_EXTENT_ITEM_KEY);
@@ -3503,15 +3714,18 @@ static noinline int find_free_extent(struct btrfs_trans_handle *trans,
 	search_start = max(search_start, first_logical_byte(root, 0));
 	search_start = max(search_start, hint_byte);
 
-	if (!last_ptr) {
+	if (!last_ptr)
 		empty_cluster = 0;
-		loop = 1;
-	}
 
 	if (search_start == hint_byte) {
 		block_group = btrfs_lookup_block_group(root->fs_info,
 						       search_start);
-		if (block_group && block_group_bits(block_group, data)) {
+		/*
+		 * we don't want to use the block group if it doesn't match our
+		 * allocation bits, or if its not cached.
+		 */
+		if (block_group && block_group_bits(block_group, data) &&
+		    block_group_cache_done(block_group)) {
 			down_read(&space_info->groups_sem);
 			if (list_empty(&block_group->list) ||
 			    block_group->ro) {
@@ -3534,21 +3748,35 @@ search:
 	down_read(&space_info->groups_sem);
 	list_for_each_entry(block_group, &space_info->block_groups, list) {
 		u64 offset;
+		int cached;
 
 		atomic_inc(&block_group->count);
 		search_start = block_group->key.objectid;
 
 have_block_group:
-		if (unlikely(!block_group->cached)) {
-			mutex_lock(&block_group->cache_mutex);
-			ret = cache_block_group(root, block_group);
-			mutex_unlock(&block_group->cache_mutex);
-			if (ret) {
-				btrfs_put_block_group(block_group);
-				break;
+		if (unlikely(block_group->cached == BTRFS_CACHE_NO)) {
+			/*
+			 * we want to start caching kthreads, but not too many
+			 * right off the bat so we don't overwhelm the system,
+			 * so only start them if there are less than 2 and we're
+			 * in the initial allocation phase.
+			 */
+			if (loop > LOOP_CACHING_NOWAIT ||
+			    atomic_read(&space_info->caching_threads) < 2) {
+				ret = cache_block_group(block_group);
+				BUG_ON(ret);
 			}
 		}
 
+		cached = block_group_cache_done(block_group);
+		if (unlikely(!cached)) {
+			found_uncached_bg = true;
+
+			/* if we only want cached bgs, loop */
+			if (loop == LOOP_CACHED_ONLY)
+				goto loop;
+		}
+
 		if (unlikely(block_group->ro))
 			goto loop;
 
@@ -3627,14 +3855,21 @@ refill_cluster:
 					spin_unlock(&last_ptr->refill_lock);
 					goto checks;
 				}
+			} else if (!cached && loop > LOOP_CACHING_NOWAIT) {
+				spin_unlock(&last_ptr->refill_lock);
+
+				wait_block_group_cache_progress(block_group,
+				       num_bytes + empty_cluster + empty_size);
+				goto have_block_group;
 			}
+
 			/*
 			 * at this point we either didn't find a cluster
 			 * or we weren't able to allocate a block from our
 			 * cluster.  Free the cluster we've been trying
 			 * to use, and go to the next block group
 			 */
-			if (loop < 2) {
+			if (loop < LOOP_NO_EMPTY_SIZE) {
 				btrfs_return_cluster_to_free_space(NULL,
 								   last_ptr);
 				spin_unlock(&last_ptr->refill_lock);
@@ -3645,8 +3880,15 @@ refill_cluster:
 
 		offset = btrfs_find_space_for_alloc(block_group, search_start,
 						    num_bytes, empty_size);
-		if (!offset)
+		if (!offset && (cached || (!cached &&
+					   loop == LOOP_CACHING_NOWAIT))) {
 			goto loop;
+		} else if (!offset && (!cached &&
+				       loop > LOOP_CACHING_NOWAIT)) {
+			wait_block_group_cache_progress(block_group,
+					num_bytes + empty_size);
+			goto have_block_group;
+		}
 checks:
 		search_start = stripe_align(root, offset);
 		/* move on to the next group */
@@ -3694,13 +3936,26 @@ loop:
 	}
 	up_read(&space_info->groups_sem);
 
-	/* loop == 0, try to find a clustered alloc in every block group
-	 * loop == 1, try again after forcing a chunk allocation
-	 * loop == 2, set empty_size and empty_cluster to 0 and try again
+	/* LOOP_CACHED_ONLY, only search fully cached block groups
+	 * LOOP_CACHING_NOWAIT, search partially cached block groups, but
+	 *			dont wait foR them to finish caching
+	 * LOOP_CACHING_WAIT, search everything, and wait if our bg is caching
+	 * LOOP_ALLOC_CHUNK, force a chunk allocation and try again
+	 * LOOP_NO_EMPTY_SIZE, set empty_size and empty_cluster to 0 and try
+	 *			again
 	 */
-	if (!ins->objectid && loop < 3 &&
-	    (empty_size || empty_cluster || allowed_chunk_alloc)) {
-		if (loop >= 2) {
+	if (!ins->objectid && loop < LOOP_NO_EMPTY_SIZE &&
+	    (found_uncached_bg || empty_size || empty_cluster ||
+	     allowed_chunk_alloc)) {
+		if (found_uncached_bg) {
+			found_uncached_bg = false;
+			if (loop < LOOP_CACHING_WAIT) {
+				loop++;
+				goto search;
+			}
+		}
+
+		if (loop == LOOP_ALLOC_CHUNK) {
 			empty_size = 0;
 			empty_cluster = 0;
 		}
@@ -3713,7 +3968,7 @@ loop:
 			space_info->force_alloc = 1;
 		}
 
-		if (loop < 3) {
+		if (loop < LOOP_NO_EMPTY_SIZE) {
 			loop++;
 			goto search;
 		}
@@ -3809,7 +4064,7 @@ again:
 			       num_bytes, data, 1);
 		goto again;
 	}
-	if (ret) {
+	if (ret == -ENOSPC) {
 		struct btrfs_space_info *sinfo;
 
 		sinfo = __find_space_info(root->fs_info, data);
@@ -3817,7 +4072,6 @@ again:
 		       "wanted %llu\n", (unsigned long long)data,
 		       (unsigned long long)num_bytes);
 		dump_space_info(sinfo, num_bytes);
-		BUG();
 	}
 
 	return ret;
@@ -3855,7 +4109,9 @@ int btrfs_reserve_extent(struct btrfs_trans_handle *trans,
 	ret = __btrfs_reserve_extent(trans, root, num_bytes, min_alloc_size,
 				     empty_size, hint_byte, search_end, ins,
 				     data);
-	update_reserved_extents(root, ins->objectid, ins->offset, 1);
+	if (!ret)
+		update_reserved_extents(root, ins->objectid, ins->offset, 1);
+
 	return ret;
 }
 
@@ -4017,9 +4273,9 @@ int btrfs_alloc_logged_file_extent(struct btrfs_trans_handle *trans,
 	struct btrfs_block_group_cache *block_group;
 
 	block_group = btrfs_lookup_block_group(root->fs_info, ins->objectid);
-	mutex_lock(&block_group->cache_mutex);
-	cache_block_group(root, block_group);
-	mutex_unlock(&block_group->cache_mutex);
+	cache_block_group(block_group);
+	wait_event(block_group->caching_q,
+		   block_group_cache_done(block_group));
 
 	ret = btrfs_remove_free_space(block_group, ins->objectid,
 				      ins->offset);
@@ -4050,7 +4306,8 @@ static int alloc_tree_block(struct btrfs_trans_handle *trans,
 	ret = __btrfs_reserve_extent(trans, root, num_bytes, num_bytes,
 				     empty_size, hint_byte, search_end,
 				     ins, 0);
-	BUG_ON(ret);
+	if (ret)
+		return ret;
 
 	if (root_objectid == BTRFS_TREE_RELOC_OBJECTID) {
 		if (parent == 0)
@@ -6966,11 +7223,16 @@ int btrfs_free_block_groups(struct btrfs_fs_info *info)
 			 &info->block_group_cache_tree);
 		spin_unlock(&info->block_group_cache_lock);
 
-		btrfs_remove_free_space_cache(block_group);
 		down_write(&block_group->space_info->groups_sem);
 		list_del(&block_group->list);
 		up_write(&block_group->space_info->groups_sem);
 
+		if (block_group->cached == BTRFS_CACHE_STARTED)
+			wait_event(block_group->caching_q,
+				   block_group_cache_done(block_group));
+
+		btrfs_remove_free_space_cache(block_group);
+
 		WARN_ON(atomic_read(&block_group->count) != 1);
 		kfree(block_group);
 
@@ -7036,10 +7298,10 @@ int btrfs_read_block_groups(struct btrfs_root *root)
 		atomic_set(&cache->count, 1);
 		spin_lock_init(&cache->lock);
 		spin_lock_init(&cache->tree_lock);
-		mutex_init(&cache->cache_mutex);
+		cache->fs_info = info;
+		init_waitqueue_head(&cache->caching_q);
 		INIT_LIST_HEAD(&cache->list);
 		INIT_LIST_HEAD(&cache->cluster_list);
-		cache->sectorsize = root->sectorsize;
 
 		/*
 		 * we only want to have 32k of ram per block group for keeping
@@ -7057,6 +7319,26 @@ int btrfs_read_block_groups(struct btrfs_root *root)
 		key.objectid = found_key.objectid + found_key.offset;
 		btrfs_release_path(root, path);
 		cache->flags = btrfs_block_group_flags(&cache->item);
+		cache->sectorsize = root->sectorsize;
+
+		remove_sb_from_cache(root, cache);
+
+		/*
+		 * check for two cases, either we are full, and therefore
+		 * don't need to bother with the caching work since we won't
+		 * find any space, or we are empty, and we can just add all
+		 * the space in and be done with it.  This saves us _alot_ of
+		 * time, particularly in the full case.
+		 */
+		if (found_key.offset == btrfs_block_group_used(&cache->item)) {
+			cache->cached = BTRFS_CACHE_FINISHED;
+		} else if (btrfs_block_group_used(&cache->item) == 0) {
+			cache->cached = BTRFS_CACHE_FINISHED;
+			add_new_free_space(cache, root->fs_info,
+					   found_key.objectid,
+					   found_key.objectid +
+					   found_key.offset);
+		}
 
 		ret = update_space_info(info, cache->flags, found_key.offset,
 					btrfs_block_group_used(&cache->item),
@@ -7112,7 +7394,7 @@ int btrfs_make_block_group(struct btrfs_trans_handle *trans,
 	atomic_set(&cache->count, 1);
 	spin_lock_init(&cache->lock);
 	spin_lock_init(&cache->tree_lock);
-	mutex_init(&cache->cache_mutex);
+	init_waitqueue_head(&cache->caching_q);
 	INIT_LIST_HEAD(&cache->list);
 	INIT_LIST_HEAD(&cache->cluster_list);
 
@@ -7121,11 +7403,12 @@ int btrfs_make_block_group(struct btrfs_trans_handle *trans,
 	cache->flags = type;
 	btrfs_set_block_group_flags(&cache->item, type);
 
-	cache->cached = 1;
-	ret = btrfs_add_free_space(cache, chunk_offset, size);
-	BUG_ON(ret);
+	cache->cached = BTRFS_CACHE_FINISHED;
 	remove_sb_from_cache(root, cache);
 
+	add_new_free_space(cache, root->fs_info, chunk_offset,
+			   chunk_offset + size);
+
 	ret = update_space_info(root->fs_info, cache->flags, size, bytes_used,
 				&cache->space_info);
 	BUG_ON(ret);
@@ -7184,7 +7467,7 @@ int btrfs_remove_block_group(struct btrfs_trans_handle *trans,
 	rb_erase(&block_group->cache_node,
 		 &root->fs_info->block_group_cache_tree);
 	spin_unlock(&root->fs_info->block_group_cache_lock);
-	btrfs_remove_free_space_cache(block_group);
+
 	down_write(&block_group->space_info->groups_sem);
 	/*
 	 * we must use list_del_init so people can check to see if they
@@ -7193,6 +7476,12 @@ int btrfs_remove_block_group(struct btrfs_trans_handle *trans,
 	list_del_init(&block_group->list);
 	up_write(&block_group->space_info->groups_sem);
 
+	if (block_group->cached == BTRFS_CACHE_STARTED)
+		wait_event(block_group->caching_q,
+			   block_group_cache_done(block_group));
+
+	btrfs_remove_free_space_cache(block_group);
+
 	spin_lock(&block_group->space_info->lock);
 	block_group->space_info->total_bytes -= block_group->key.offset;
 	block_group->space_info->bytes_readonly -= block_group->key.offset;
diff --git a/fs/btrfs/free-space-cache.c b/fs/btrfs/free-space-cache.c
index ab8cad8b46c..af99b78b288 100644
--- a/fs/btrfs/free-space-cache.c
+++ b/fs/btrfs/free-space-cache.c
@@ -238,6 +238,7 @@ static void unlink_free_space(struct btrfs_block_group_cache *block_group,
 {
 	rb_erase(&info->offset_index, &block_group->free_space_offset);
 	block_group->free_extents--;
+	block_group->free_space -= info->bytes;
 }
 
 static int link_free_space(struct btrfs_block_group_cache *block_group,
@@ -251,6 +252,7 @@ static int link_free_space(struct btrfs_block_group_cache *block_group,
 	if (ret)
 		return ret;
 
+	block_group->free_space += info->bytes;
 	block_group->free_extents++;
 	return ret;
 }
@@ -285,36 +287,40 @@ static void recalculate_thresholds(struct btrfs_block_group_cache *block_group)
 	}
 }
 
-static void bitmap_clear_bits(struct btrfs_free_space *info, u64 offset, u64 bytes,
-			      u64 sectorsize)
+static void bitmap_clear_bits(struct btrfs_block_group_cache *block_group,
+			      struct btrfs_free_space *info, u64 offset,
+			      u64 bytes)
 {
 	unsigned long start, end;
 	unsigned long i;
 
-	start = offset_to_bit(info->offset, sectorsize, offset);
-	end = start + bytes_to_bits(bytes, sectorsize);
+	start = offset_to_bit(info->offset, block_group->sectorsize, offset);
+	end = start + bytes_to_bits(bytes, block_group->sectorsize);
 	BUG_ON(end > BITS_PER_BITMAP);
 
 	for (i = start; i < end; i++)
 		clear_bit(i, info->bitmap);
 
 	info->bytes -= bytes;
+	block_group->free_space -= bytes;
 }
 
-static void bitmap_set_bits(struct btrfs_free_space *info, u64 offset, u64 bytes,
-			    u64 sectorsize)
+static void bitmap_set_bits(struct btrfs_block_group_cache *block_group,
+			    struct btrfs_free_space *info, u64 offset,
+			    u64 bytes)
 {
 	unsigned long start, end;
 	unsigned long i;
 
-	start = offset_to_bit(info->offset, sectorsize, offset);
-	end = start + bytes_to_bits(bytes, sectorsize);
+	start = offset_to_bit(info->offset, block_group->sectorsize, offset);
+	end = start + bytes_to_bits(bytes, block_group->sectorsize);
 	BUG_ON(end > BITS_PER_BITMAP);
 
 	for (i = start; i < end; i++)
 		set_bit(i, info->bitmap);
 
 	info->bytes += bytes;
+	block_group->free_space += bytes;
 }
 
 static int search_bitmap(struct btrfs_block_group_cache *block_group,
@@ -414,13 +420,12 @@ again:
 		(u64)(BITS_PER_BITMAP * block_group->sectorsize) - 1;
 
 	if (*offset > bitmap_info->offset && *offset + *bytes > end) {
-		bitmap_clear_bits(bitmap_info, *offset,
-				  end - *offset + 1, block_group->sectorsize);
+		bitmap_clear_bits(block_group, bitmap_info, *offset,
+				  end - *offset + 1);
 		*bytes -= end - *offset + 1;
 		*offset = end + 1;
 	} else if (*offset >= bitmap_info->offset && *offset + *bytes <= end) {
-		bitmap_clear_bits(bitmap_info, *offset,
-				  *bytes, block_group->sectorsize);
+		bitmap_clear_bits(block_group, bitmap_info, *offset, *bytes);
 		*bytes = 0;
 	}
 
@@ -495,14 +500,13 @@ again:
 		(u64)(BITS_PER_BITMAP * block_group->sectorsize);
 
 	if (offset >= bitmap_info->offset && offset + bytes > end) {
-		bitmap_set_bits(bitmap_info, offset, end - offset,
-				block_group->sectorsize);
+		bitmap_set_bits(block_group, bitmap_info, offset,
+				end - offset);
 		bytes -= end - offset;
 		offset = end;
 		added = 0;
 	} else if (offset >= bitmap_info->offset && offset + bytes <= end) {
-		bitmap_set_bits(bitmap_info, offset, bytes,
-				block_group->sectorsize);
+		bitmap_set_bits(block_group, bitmap_info, offset, bytes);
 		bytes = 0;
 	} else {
 		BUG();
@@ -870,8 +874,7 @@ u64 btrfs_find_space_for_alloc(struct btrfs_block_group_cache *block_group,
 
 	ret = offset;
 	if (entry->bitmap) {
-		bitmap_clear_bits(entry, offset, bytes,
-				  block_group->sectorsize);
+		bitmap_clear_bits(block_group, entry, offset, bytes);
 		if (!entry->bytes) {
 			unlink_free_space(block_group, entry);
 			kfree(entry->bitmap);
@@ -891,6 +894,7 @@ u64 btrfs_find_space_for_alloc(struct btrfs_block_group_cache *block_group,
 
 out:
 	spin_unlock(&block_group->tree_lock);
+
 	return ret;
 }
 
@@ -967,7 +971,7 @@ static u64 btrfs_alloc_from_bitmap(struct btrfs_block_group_cache *block_group,
 		goto out;
 
 	ret = search_start;
-	bitmap_clear_bits(entry, ret, bytes, block_group->sectorsize);
+	bitmap_clear_bits(block_group, entry, ret, bytes);
 out:
 	spin_unlock(&cluster->lock);
 	spin_unlock(&block_group->tree_lock);
diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c
index 81f7124c305..32454d1c566 100644
--- a/fs/btrfs/transaction.c
+++ b/fs/btrfs/transaction.c
@@ -40,6 +40,14 @@ static noinline void put_transaction(struct btrfs_transaction *transaction)
 	}
 }
 
+static noinline void switch_commit_root(struct btrfs_root *root)
+{
+	down_write(&root->commit_root_sem);
+	free_extent_buffer(root->commit_root);
+	root->commit_root = btrfs_root_node(root);
+	up_write(&root->commit_root_sem);
+}
+
 /*
  * either allocate a new transaction or hop into the existing one
  */
@@ -458,8 +466,7 @@ static int update_cowonly_root(struct btrfs_trans_handle *trans,
 		ret = btrfs_write_dirty_block_groups(trans, root);
 		BUG_ON(ret);
 	}
-	free_extent_buffer(root->commit_root);
-	root->commit_root = btrfs_root_node(root);
+	switch_commit_root(root);
 	return 0;
 }
 
@@ -537,8 +544,7 @@ static noinline int commit_fs_roots(struct btrfs_trans_handle *trans,
 			btrfs_update_reloc_root(trans, root);
 
 			if (root->commit_root != root->node) {
-				free_extent_buffer(root->commit_root);
-				root->commit_root = btrfs_root_node(root);
+				switch_commit_root(root);
 				btrfs_set_root_node(&root->root_item,
 						    root->node);
 			}
@@ -1002,15 +1008,11 @@ int btrfs_commit_transaction(struct btrfs_trans_handle *trans,
 
 	btrfs_set_root_node(&root->fs_info->tree_root->root_item,
 			    root->fs_info->tree_root->node);
-	free_extent_buffer(root->fs_info->tree_root->commit_root);
-	root->fs_info->tree_root->commit_root =
-				btrfs_root_node(root->fs_info->tree_root);
+	switch_commit_root(root->fs_info->tree_root);
 
 	btrfs_set_root_node(&root->fs_info->chunk_root->root_item,
 			    root->fs_info->chunk_root->node);
-	free_extent_buffer(root->fs_info->chunk_root->commit_root);
-	root->fs_info->chunk_root->commit_root =
-				btrfs_root_node(root->fs_info->chunk_root);
+	switch_commit_root(root->fs_info->chunk_root);
 
 	update_super_roots(root);
 
@@ -1050,6 +1052,7 @@ int btrfs_commit_transaction(struct btrfs_trans_handle *trans,
 	cur_trans->commit_done = 1;
 
 	root->fs_info->last_trans_committed = cur_trans->transid;
+
 	wake_up(&cur_trans->commit_wait);
 
 	put_transaction(cur_trans);
diff --git a/fs/btrfs/tree-log.c b/fs/btrfs/tree-log.c
index c13922206d1..19560686261 100644
--- a/fs/btrfs/tree-log.c
+++ b/fs/btrfs/tree-log.c
@@ -264,7 +264,7 @@ static int process_one_buffer(struct btrfs_root *log,
 {
 	if (wc->pin)
 		btrfs_update_pinned_extents(log->fs_info->extent_root,
-					    eb->start, eb->len, 1);
+					    eb->start, eb->len, 1, 0);
 
 	if (btrfs_buffer_uptodate(eb, gen)) {
 		if (wc->write)
-- 
GitLab


From 20736abaa361bea488df6a1f66f6b37fb01107b9 Mon Sep 17 00:00:00 2001
From: Diego Calleja <diegocg@gmail.com>
Date: Fri, 24 Jul 2009 11:06:52 -0400
Subject: [PATCH 0085/1153] Btrfs: Remove code duplication in comp_keys

comp_keys is duplicating what is done in btrfs_comp_cpu_keys, so just
call it.

Signed-off-by: Diego Calleja <diegocg@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/ctree.c | 14 +-------------
 1 file changed, 1 insertion(+), 13 deletions(-)

diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c
index fdd423a550d..91572091c0a 100644
--- a/fs/btrfs/ctree.c
+++ b/fs/btrfs/ctree.c
@@ -557,19 +557,7 @@ static int comp_keys(struct btrfs_disk_key *disk, struct btrfs_key *k2)
 
 	btrfs_disk_key_to_cpu(&k1, disk);
 
-	if (k1.objectid > k2->objectid)
-		return 1;
-	if (k1.objectid < k2->objectid)
-		return -1;
-	if (k1.type > k2->type)
-		return 1;
-	if (k1.type < k2->type)
-		return -1;
-	if (k1.offset > k2->offset)
-		return 1;
-	if (k1.offset < k2->offset)
-		return -1;
-	return 0;
+	return btrfs_comp_cpu_keys(&k1, k2);
 }
 
 /*
-- 
GitLab


From 1fcbac581be375ca0a686f72ee2b7fd1dbf386e7 Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Fri, 24 Jul 2009 11:06:53 -0400
Subject: [PATCH 0086/1153] Btrfs: find_free_dev_extent doesn't handle holes at
 the start of the device

find_free_dev_extent does not properly handle the case where
the device is not complete free, and there is a free extent
at the beginning of the device.

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/volumes.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c
index 55c37276a29..074c1c56d8c 100644
--- a/fs/btrfs/volumes.c
+++ b/fs/btrfs/volumes.c
@@ -758,9 +758,13 @@ static noinline int find_free_dev_extent(struct btrfs_trans_handle *trans,
 	ret = btrfs_search_slot(trans, root, &key, path, 0, 0);
 	if (ret < 0)
 		goto error;
-	ret = btrfs_previous_item(root, path, 0, key.type);
-	if (ret < 0)
-		goto error;
+	if (ret > 0) {
+		ret = btrfs_previous_item(root, path, key.objectid, key.type);
+		if (ret < 0)
+			goto error;
+		if (ret > 0)
+			start_found = 1;
+	}
 	l = path->nodes[0];
 	btrfs_item_key_to_cpu(l, &key, path->slots[0]);
 	while (1) {
-- 
GitLab


From 0a4eefbb745ec0e8a5b694ae3f40cc34082d8f61 Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Fri, 24 Jul 2009 11:06:53 -0400
Subject: [PATCH 0087/1153] Btrfs: Fix ordering of key field checks in
 btrfs_previous_item

Check objectid of item before checking the item type, otherwise we may return
zero for a key that is actually too low.

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/ctree.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c
index 91572091c0a..978449af4cc 100644
--- a/fs/btrfs/ctree.c
+++ b/fs/btrfs/ctree.c
@@ -4296,10 +4296,10 @@ int btrfs_previous_item(struct btrfs_root *root,
 			path->slots[0]--;
 
 		btrfs_item_key_to_cpu(leaf, &found_key, path->slots[0]);
-		if (found_key.type == type)
-			return 0;
 		if (found_key.objectid < min_objectid)
 			break;
+		if (found_key.type == type)
+			return 0;
 		if (found_key.objectid == min_objectid &&
 		    found_key.type < type)
 			break;
-- 
GitLab


From d717aa1d31c36cb56059e97966cb76f0be021969 Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Fri, 24 Jul 2009 12:42:46 -0400
Subject: [PATCH 0088/1153] Btrfs: Avoid delayed reference update looping

btrfs_split_leaf and btrfs_del_items can end up in a loop
where one is constantly spliting a given leaf and the other
is constantly merging it back with the adjacent nodes.

There is a better fix for this, but in the interest of something
small, this patch just changes btrfs_del_items back to balancing less
often.

Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/ctree.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

diff --git a/fs/btrfs/ctree.c b/fs/btrfs/ctree.c
index 978449af4cc..3fdcc0512d3 100644
--- a/fs/btrfs/ctree.c
+++ b/fs/btrfs/ctree.c
@@ -1040,9 +1040,6 @@ static noinline int balance_level(struct btrfs_trans_handle *trans,
 	    BTRFS_NODEPTRS_PER_BLOCK(root) / 4)
 		return 0;
 
-	if (btrfs_header_nritems(mid) > 2)
-		return 0;
-
 	if (btrfs_header_nritems(mid) < 2)
 		err_on_enospc = 1;
 
@@ -3796,7 +3793,7 @@ int btrfs_del_items(struct btrfs_trans_handle *trans, struct btrfs_root *root,
 		}
 
 		/* delete the leaf if it is mostly empty */
-		if (used < BTRFS_LEAF_DATA_SIZE(root) / 2) {
+		if (used < BTRFS_LEAF_DATA_SIZE(root) / 3) {
 			/* push_leaf_left fixes the path.
 			 * make sure the path still points to our leaf
 			 * for possible call to del_ptr below
-- 
GitLab


From 7194e6f9c083e87171ddfc8b746f05e007f58132 Mon Sep 17 00:00:00 2001
From: Adrian Hunter <Adrian.Hunter@nokia.com>
Date: Fri, 24 Jul 2009 17:05:00 +0300
Subject: [PATCH 0089/1153] UBI: fix double free on error path

If we fail in 'ubi_eba_init_scan()', we free
'ubi->volumes[i]->eba_tbl' in there, but also later free it
in 'free_internal_volumes()'. Fix this by assigning NULL
to 'ubi->volumes[i]->eba_tbl' after it is freed.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
---
 drivers/mtd/ubi/eba.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/mtd/ubi/eba.c b/drivers/mtd/ubi/eba.c
index 0f2034c3ed2..e4d9ef0c965 100644
--- a/drivers/mtd/ubi/eba.c
+++ b/drivers/mtd/ubi/eba.c
@@ -1254,6 +1254,7 @@ out_free:
 		if (!ubi->volumes[i])
 			continue;
 		kfree(ubi->volumes[i]->eba_tbl);
+		ubi->volumes[i]->eba_tbl = NULL;
 	}
 	return err;
 }
-- 
GitLab


From 32bc4820287a1a03982979515949e8ea56eac641 Mon Sep 17 00:00:00 2001
From: Adrian Hunter <Adrian.Hunter@nokia.com>
Date: Fri, 24 Jul 2009 19:16:04 +0300
Subject: [PATCH 0090/1153] UBI: compatible fallback in absense of sequence
 numbers

Fall back onto thinking everything's OK if either of the sequence
numbers we are asked to compare is zero, which is what was used
before sequence numbers were introduced.

[ Artem: modified the patch to be applicable to upstream UBI, added
        big comment ]

Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
---
 drivers/mtd/ubi/scan.c | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/ubi/scan.c b/drivers/mtd/ubi/scan.c
index a423131b617..b847745394b 100644
--- a/drivers/mtd/ubi/scan.c
+++ b/drivers/mtd/ubi/scan.c
@@ -781,11 +781,22 @@ static int process_eb(struct ubi_device *ubi, struct ubi_scan_info *si,
 			return -EINVAL;
 		}
 
+		/*
+		 * Make sure that all PEBs have the same image sequence number.
+		 * This allows us to detect situations when users flash UBI
+		 * images incorrectly, so that the flash has the new UBI image
+		 * and leftovers from the old one. This feature was added
+		 * relatively recently, and the sequence number was always
+		 * zero, because old UBI implementations always set it to zero.
+		 * For this reasons, we do not panic if some PEBs have zero
+		 * sequence number, while other PEBs have non-zero sequence
+		 * number.
+		 */
 		image_seq = be32_to_cpu(ech->image_seq);
 		if (!si->image_seq_set) {
 			ubi->image_seq = image_seq;
 			si->image_seq_set = 1;
-		} else if (ubi->image_seq != image_seq) {
+		} else if (ubi->image_seq && ubi->image_seq != image_seq) {
 			ubi_err("bad image sequence number %d in PEB %d, "
 				"expected %d", image_seq, pnum, ubi->image_seq);
 			ubi_dbg_dump_ec_hdr(ech);
-- 
GitLab


From ebecd3d9d2adba144c15f1d35c78e0c26ead1bfd Mon Sep 17 00:00:00 2001
From: Sage Weil <sage@newdream.net>
Date: Fri, 24 Jul 2009 13:17:44 -0400
Subject: [PATCH 0091/1153] Btrfs: make flushoncommit mount option correctly
 wait on ordered_extents

The commit_transaction call to wait_ordered_extents when snap_pending
passes nocow_only=1 to process only NOCOW or PREALLOC extents.  This isn't
correct for the 'flushoncommit' mode, as it skips extents we just started
IO on in start_delalloc_inodes.

So, in the flushoncommit case, wait on all ordered extents.  Otherwise,
only pass the nocow_only flag to wait_ordered_extents if snap_pending.

Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/transaction.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c
index 32454d1c566..e51d2bc532f 100644
--- a/fs/btrfs/transaction.c
+++ b/fs/btrfs/transaction.c
@@ -942,9 +942,11 @@ int btrfs_commit_transaction(struct btrfs_trans_handle *trans,
 
 		mutex_unlock(&root->fs_info->trans_mutex);
 
-		if (flush_on_commit || snap_pending) {
-			if (flush_on_commit)
-				btrfs_start_delalloc_inodes(root);
+		if (flush_on_commit) {
+			btrfs_start_delalloc_inodes(root);
+			ret = btrfs_wait_ordered_extents(root, 0);
+			BUG_ON(ret);
+		} else if (snap_pending) {
 			ret = btrfs_wait_ordered_extents(root, 1);
 			BUG_ON(ret);
 		}
-- 
GitLab


From bdff78707f3ce47e891f3201c9666122a70556ce Mon Sep 17 00:00:00 2001
From: Thomas Gleixner <tglx@linutronix.de>
Date: Fri, 24 Jul 2009 15:30:45 -0400
Subject: [PATCH 0092/1153] trace: stop tracer in oops_enter()

If trace_printk_on_oops is set we lose interesting trace information
when the tracer is enabled across oops handling and printing. We want
the trace which might give us information _WHY_ we oopsed.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 kernel/panic.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/kernel/panic.c b/kernel/panic.c
index 984b3ecbd72..512ab73b0ca 100644
--- a/kernel/panic.c
+++ b/kernel/panic.c
@@ -301,6 +301,7 @@ int oops_may_print(void)
  */
 void oops_enter(void)
 {
+	tracing_off();
 	/* can't trust the integrity of the kernel anymore: */
 	debug_locks_off();
 	do_oops_enter_exit();
-- 
GitLab


From 283bb1979fa8580c4037d8df251449368c292a3b Mon Sep 17 00:00:00 2001
From: Chris Mason <chris.mason@oracle.com>
Date: Fri, 24 Jul 2009 16:30:55 -0400
Subject: [PATCH 0093/1153] Btrfs: clear all space_info->full after removing a
 block group

Btrfs allocates individual extents from block groups, and each
block group has a specific type.  It may hold metadata, data
mirrored or striped etc.

When we balance space (btrfs-vol -b) or remove a drive (btrfs-vol -r)
we free block groups.  Once a block group is freed, the space it was
using on the device may be available for use by new block groups.

btrfs_remove_block_group was clearing the flag that said
'our devices are full, don't even try to allocate new block groups',
but it was only clearing that flag for a specific type of block group.

This commit clears the full flag for all of the types of block groups,
making it much more likely that we'll be able to balance space when
the drive is close to full.

Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/extent-tree.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index 9a489cc89fd..508df5f7d2e 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -7486,7 +7486,8 @@ int btrfs_remove_block_group(struct btrfs_trans_handle *trans,
 	block_group->space_info->total_bytes -= block_group->key.offset;
 	block_group->space_info->bytes_readonly -= block_group->key.offset;
 	spin_unlock(&block_group->space_info->lock);
-	block_group->space_info->full = 0;
+
+	btrfs_clear_space_info_full(root->fs_info);
 
 	btrfs_put_block_group(block_group);
 	btrfs_put_block_group(block_group);
-- 
GitLab


From 9779b72f0584fd53e0de53f62f205bf0dc0db553 Mon Sep 17 00:00:00 2001
From: Chris Mason <chris.mason@oracle.com>
Date: Fri, 24 Jul 2009 16:41:41 -0400
Subject: [PATCH 0094/1153] Btrfs: find smallest available device extent during
 chunk allocation

Allocating new block group is easy when the disk has plenty of space.
But things get difficult as the disk fills up, especially if
the FS has been run through btrfs-vol -b.  The balance operation
is likely to make the total bytes available on the device greater
than the largest extent we'll actually be able to allocate.

But the device extent allocation code incorrectly assumes that a device
with 5G free will be able to allocate a 5G extent.  It isn't normally a
problem because device extents don't get freed unless btrfs-vol -b
is run.

This fixes the device extent allocator to remember the largest free
extent it can find, and then uses that value as a fallback.

Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/volumes.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/fs/btrfs/volumes.c b/fs/btrfs/volumes.c
index 074c1c56d8c..5dbefd11b4a 100644
--- a/fs/btrfs/volumes.c
+++ b/fs/btrfs/volumes.c
@@ -721,7 +721,8 @@ error:
  */
 static noinline int find_free_dev_extent(struct btrfs_trans_handle *trans,
 					 struct btrfs_device *device,
-					 u64 num_bytes, u64 *start)
+					 u64 num_bytes, u64 *start,
+					 u64 *max_avail)
 {
 	struct btrfs_key key;
 	struct btrfs_root *root = device->dev_root;
@@ -807,6 +808,10 @@ no_more_items:
 			if (last_byte < search_start)
 				last_byte = search_start;
 			hole_size = key.offset - last_byte;
+
+			if (hole_size > *max_avail)
+				*max_avail = hole_size;
+
 			if (key.offset > last_byte &&
 			    hole_size >= num_bytes) {
 				*start = last_byte;
@@ -1625,6 +1630,7 @@ static int __btrfs_grow_device(struct btrfs_trans_handle *trans,
 	device->fs_devices->total_rw_bytes += diff;
 
 	device->total_bytes = new_size;
+	device->disk_total_bytes = new_size;
 	btrfs_clear_space_info_full(device->dev_root->fs_info);
 
 	return btrfs_update_device(trans, device);
@@ -2175,6 +2181,7 @@ static int __btrfs_alloc_chunk(struct btrfs_trans_handle *trans,
 			     max_chunk_size);
 
 again:
+	max_avail = 0;
 	if (!map || map->num_stripes != num_stripes) {
 		kfree(map);
 		map = kmalloc(map_lookup_size(num_stripes), GFP_NOFS);
@@ -2223,7 +2230,8 @@ again:
 
 		if (device->in_fs_metadata && avail >= min_free) {
 			ret = find_free_dev_extent(trans, device,
-						   min_free, &dev_offset);
+						   min_free, &dev_offset,
+						   &max_avail);
 			if (ret == 0) {
 				list_move_tail(&device->dev_alloc_list,
 					       &private_devs);
-- 
GitLab


From 58cda884ecc87dcce18d463b0c8bd928dae63ad8 Mon Sep 17 00:00:00 2001
From: Jean Pihet <jpihet@mvista.com>
Date: Fri, 24 Jul 2009 19:43:25 -0600
Subject: [PATCH 0095/1153] OMAP3 SDRC: add support for 2 SDRAM chip selects

Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.

This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS

Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers

Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).

Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/mach-omap2/board-2430sdp.c      |   2 +-
 arch/arm/mach-omap2/board-3430sdp.c      |   2 +-
 arch/arm/mach-omap2/board-4430sdp.c      |   2 +-
 arch/arm/mach-omap2/board-apollon.c      |   2 +-
 arch/arm/mach-omap2/board-generic.c      |   2 +-
 arch/arm/mach-omap2/board-h4.c           |   2 +-
 arch/arm/mach-omap2/board-ldp.c          |   2 +-
 arch/arm/mach-omap2/board-omap3beagle.c  |   3 +-
 arch/arm/mach-omap2/board-omap3evm.c     |   2 +-
 arch/arm/mach-omap2/board-omap3pandora.c |   3 +-
 arch/arm/mach-omap2/board-overo.c        |   3 +-
 arch/arm/mach-omap2/board-rx51.c         |   2 +-
 arch/arm/mach-omap2/board-zoom2.c        |   2 +-
 arch/arm/mach-omap2/clock34xx.c          |  37 ++++--
 arch/arm/mach-omap2/io.c                 |   5 +-
 arch/arm/mach-omap2/sdrc.c               |  63 +++++++----
 arch/arm/mach-omap2/sram34xx.S           | 137 ++++++++++++++++++-----
 arch/arm/plat-omap/include/mach/io.h     |   3 +-
 arch/arm/plat-omap/include/mach/sdrc.h   |  11 +-
 arch/arm/plat-omap/include/mach/sram.h   |  23 ++--
 arch/arm/plat-omap/sram.c                |  30 +++--
 21 files changed, 236 insertions(+), 102 deletions(-)

diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c
index 9c3fdcdf76c..8ec2a132904 100644
--- a/arch/arm/mach-omap2/board-2430sdp.c
+++ b/arch/arm/mach-omap2/board-2430sdp.c
@@ -141,7 +141,7 @@ static inline void board_smc91x_init(void)
 
 static void __init omap_2430sdp_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 }
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 496a90e4ea7..ac262cd7450 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -169,7 +169,7 @@ static struct platform_device *sdp3430_devices[] __initdata = {
 
 static void __init omap_3430sdp_init_irq(void)
 {
-	omap2_init_common_hw(hyb18m512160af6_sdrc_params);
+	omap2_init_common_hw(hyb18m512160af6_sdrc_params, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 }
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 57e477bd89c..b0c7402248f 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -59,7 +59,7 @@ static void __init gic_init_irq(void)
 
 static void __init omap_4430sdp_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 #ifdef CONFIG_OMAP_32K_TIMER
 	omap2_gp_clockevent_set_gptimer(1);
 #endif
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 06dfba888b0..dcfc20d0389 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -250,7 +250,7 @@ out:
 
 static void __init omap_apollon_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 	apollon_init_smc91x();
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 3492162a65c..fd00aa03690 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -33,7 +33,7 @@
 
 static void __init omap_generic_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 }
 
diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c
index e7d017cdc43..7b1d61d5bb2 100644
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c
@@ -270,7 +270,7 @@ static void __init h4_init_flash(void)
 
 static void __init omap_h4_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 	h4_init_flash();
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index d8bc0a7dcb8..ea383f88cb1 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -270,7 +270,7 @@ static inline void __init ldp_init_smsc911x(void)
 
 static void __init omap_ldp_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 	ldp_init_smsc911x();
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 991ac9c3803..4abefd9566e 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -282,7 +282,8 @@ static int __init omap3_beagle_i2c_init(void)
 
 static void __init omap3_beagle_init_irq(void)
 {
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+			     mt46h32m32lf6_sdrc_params);
 	omap_init_irq();
 #ifdef CONFIG_OMAP_32K_TIMER
 	omap2_gp_clockevent_set_gptimer(12);
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index d3cc145814d..217e5a2861d 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -279,7 +279,7 @@ struct spi_board_info omap3evm_spi_board_info[] = {
 
 static void __init omap3_evm_init_irq(void)
 {
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 	omap3evm_init_smc911x();
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index e32aa23ce96..9b991ced382 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -310,7 +310,8 @@ static int __init omap3pandora_i2c_init(void)
 
 static void __init omap3pandora_init_irq(void)
 {
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+			     mt46h32m32lf6_sdrc_params);
 	omap_init_irq();
 	omap_gpio_init();
 }
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index dff5528fbfb..44bc1c54cd0 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -360,7 +360,8 @@ static int __init overo_i2c_init(void)
 
 static void __init overo_init_irq(void)
 {
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+			     mt46h32m32lf6_sdrc_params);
 	omap_init_irq();
 	omap_gpio_init();
 }
diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c
index 374ff63c3eb..591ae8a5805 100644
--- a/arch/arm/mach-omap2/board-rx51.c
+++ b/arch/arm/mach-omap2/board-rx51.c
@@ -61,7 +61,7 @@ static struct omap_board_config_kernel rx51_config[] = {
 
 static void __init rx51_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 }
diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c
index bcc0f7632de..427b7b8b123 100644
--- a/arch/arm/mach-omap2/board-zoom2.c
+++ b/arch/arm/mach-omap2/board-zoom2.c
@@ -25,7 +25,7 @@
 
 static void __init omap_zoom2_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 }
diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c
index 045da923e75..1c6480d3ad6 100644
--- a/arch/arm/mach-omap2/clock34xx.c
+++ b/arch/arm/mach-omap2/clock34xx.c
@@ -725,7 +725,9 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
 	u32 unlock_dll = 0;
 	u32 c;
 	unsigned long validrate, sdrcrate, mpurate;
-	struct omap_sdrc_params *sp;
+	struct omap_sdrc_params *sdrc_cs0;
+	struct omap_sdrc_params *sdrc_cs1;
+	int ret;
 
 	if (!clk || !rate)
 		return -EINVAL;
@@ -743,8 +745,8 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
 	else
 		sdrcrate >>= ((clk->rate / rate) >> 1);
 
-	sp = omap2_sdrc_get_params(sdrcrate);
-	if (!sp)
+	ret = omap2_sdrc_get_params(sdrcrate, &sdrc_cs0, &sdrc_cs1);
+	if (ret)
 		return -EINVAL;
 
 	if (sdrcrate < MIN_SDRC_DLL_LOCK_FREQ) {
@@ -765,12 +767,29 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
 
 	pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate,
 		 validrate);
-	pr_debug("clock: SDRC timing params used: %08x %08x %08x\n",
-		 sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb);
-
-	omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla,
-				  sp->actim_ctrlb, new_div, unlock_dll, c,
-				  sp->mr, rate > clk->rate);
+	pr_debug("clock: SDRC CS0 timing params used:"
+		 " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n",
+		 sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
+		 sdrc_cs0->actim_ctrlb, sdrc_cs0->mr);
+	if (sdrc_cs1)
+		pr_debug("clock: SDRC CS1 timing params used: "
+		 " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n",
+		 sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla,
+		 sdrc_cs1->actim_ctrlb, sdrc_cs1->mr);
+
+	if (sdrc_cs1)
+		omap3_configure_core_dpll(
+				  new_div, unlock_dll, c, rate > clk->rate,
+				  sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
+				  sdrc_cs0->actim_ctrlb, sdrc_cs0->mr,
+				  sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla,
+				  sdrc_cs1->actim_ctrlb, sdrc_cs1->mr);
+	else
+		omap3_configure_core_dpll(
+				  new_div, unlock_dll, c, rate > clk->rate,
+				  sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
+				  sdrc_cs0->actim_ctrlb, sdrc_cs0->mr,
+				  0, 0, 0, 0);
 
 	return 0;
 }
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index 3a86b0f6603..e9b9bcb19b4 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -276,14 +276,15 @@ static int __init _omap2_init_reprogram_sdrc(void)
 	return v;
 }
 
-void __init omap2_init_common_hw(struct omap_sdrc_params *sp)
+void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
+				 struct omap_sdrc_params *sdrc_cs1)
 {
 	omap2_mux_init();
 #ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */
 	pwrdm_init(powerdomains_omap);
 	clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps);
 	omap2_clk_init();
-	omap2_sdrc_init(sp);
+	omap2_sdrc_init(sdrc_cs0, sdrc_cs1);
 	_omap2_init_reprogram_sdrc();
 #endif
 	gpmc_init();
diff --git a/arch/arm/mach-omap2/sdrc.c b/arch/arm/mach-omap2/sdrc.c
index 2045441e838..2e9e38db30e 100644
--- a/arch/arm/mach-omap2/sdrc.c
+++ b/arch/arm/mach-omap2/sdrc.c
@@ -32,7 +32,7 @@
 #include <mach/sdrc.h>
 #include "sdrc.h"
 
-static struct omap_sdrc_params *sdrc_init_params;
+static struct omap_sdrc_params *sdrc_init_params_cs0, *sdrc_init_params_cs1;
 
 void __iomem *omap2_sdrc_base;
 void __iomem *omap2_sms_base;
@@ -45,33 +45,49 @@ void __iomem *omap2_sms_base;
 /**
  * omap2_sdrc_get_params - return SDRC register values for a given clock rate
  * @r: SDRC clock rate (in Hz)
+ * @sdrc_cs0: chip select 0 ram timings **
+ * @sdrc_cs1: chip select 1 ram timings **
  *
  * Return pre-calculated values for the SDRC_ACTIM_CTRLA,
- * SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL, and SDRC_MR registers, for a given
- * SDRC clock rate 'r'.  These parameters control various timing
- * delays in the SDRAM controller that are expressed in terms of the
- * number of SDRC clock cycles to wait; hence the clock rate
- * dependency. Note that sdrc_init_params must be sorted rate
- * descending.  Also assumes that both chip-selects use the same
- * timing parameters.  Returns a struct omap_sdrc_params * upon
- * success, or NULL upon failure.
+ *  SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL and SDRC_MR registers in sdrc_cs[01]
+ *  structs,for a given SDRC clock rate 'r'.
+ * These parameters control various timing delays in the SDRAM controller
+ *  that are expressed in terms of the number of SDRC clock cycles to
+ *  wait; hence the clock rate dependency.
+ *
+ * Supports 2 different timing parameters for both chip selects.
+ *
+ * Note 1: the sdrc_init_params_cs[01] must be sorted rate descending.
+ * Note 2: If sdrc_init_params_cs_1 is not NULL it must be of same size
+ *  as sdrc_init_params_cs_0.
+ *
+ * Fills in the struct omap_sdrc_params * for each chip select.
+ * Returns 0 upon success or -1 upon failure.
  */
-struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r)
+int omap2_sdrc_get_params(unsigned long r,
+			  struct omap_sdrc_params **sdrc_cs0,
+			  struct omap_sdrc_params **sdrc_cs1)
 {
-	struct omap_sdrc_params *sp;
+	struct omap_sdrc_params *sp0, *sp1;
 
-	if (!sdrc_init_params)
-		return NULL;
+	if (!sdrc_init_params_cs0)
+		return -1;
 
-	sp = sdrc_init_params;
+	sp0 = sdrc_init_params_cs0;
+	sp1 = sdrc_init_params_cs1;
 
-	while (sp->rate && sp->rate != r)
-		sp++;
+	while (sp0->rate && sp0->rate != r) {
+		sp0++;
+		if (sdrc_init_params_cs1)
+			sp1++;
+	}
 
-	if (!sp->rate)
-		return NULL;
+	if (!sp0->rate)
+		return -1;
 
-	return sp;
+	*sdrc_cs0 = sp0;
+	*sdrc_cs1 = sp1;
+	return 0;
 }
 
 
@@ -83,13 +99,15 @@ void __init omap2_set_globals_sdrc(struct omap_globals *omap2_globals)
 
 /**
  * omap2_sdrc_init - initialize SMS, SDRC devices on boot
- * @sp: pointer to a null-terminated list of struct omap_sdrc_params
+ * @sdrc_cs[01]: pointers to a null-terminated list of struct omap_sdrc_params
+ *  Support for 2 chip selects timings
  *
  * Turn on smart idle modes for SDRAM scheduler and controller.
  * Program a known-good configuration for the SDRC to deal with buggy
  * bootloaders.
  */
-void __init omap2_sdrc_init(struct omap_sdrc_params *sp)
+void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
+			    struct omap_sdrc_params *sdrc_cs1)
 {
 	u32 l;
 
@@ -103,7 +121,8 @@ void __init omap2_sdrc_init(struct omap_sdrc_params *sp)
 	l |= (0x2 << 3);
 	sdrc_write_reg(l, SDRC_SYSCONFIG);
 
-	sdrc_init_params = sp;
+	sdrc_init_params_cs0 = sdrc_cs0;
+	sdrc_init_params_cs1 = sdrc_cs1;
 
 	/* XXX Enable SRFRONIDLEREQ here also? */
 	l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) |
diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S
index f41f8d96ddb..3aef7448b2a 100644
--- a/arch/arm/mach-omap2/sram34xx.S
+++ b/arch/arm/mach-omap2/sram34xx.S
@@ -36,7 +36,7 @@
 
 	.text
 
-/* r4 parameters */
+/* r1 parameters */
 #define SDRC_NO_UNLOCK_DLL		0x0
 #define SDRC_UNLOCK_DLL			0x1
 
@@ -71,40 +71,71 @@
 
 /*
  * omap3_sram_configure_core_dpll - change DPLL3 M2 divider
- * r0 = new SDRC_RFR_CTRL register contents
- * r1 = new SDRC_ACTIM_CTRLA register contents
- * r2 = new SDRC_ACTIM_CTRLB register contents
- * r3 = new M2 divider setting (only 1 and 2 supported right now)
- * r4 = unlock SDRC DLL? (1 = yes, 0 = no).  Only unlock DLL for
+ *
+ * Params passed in registers:
+ *  r0 = new M2 divider setting (only 1 and 2 supported right now)
+ *  r1 = unlock SDRC DLL? (1 = yes, 0 = no).  Only unlock DLL for
  *      SDRC rates < 83MHz
- * r5 = number of MPU cycles to wait for SDRC to stabilize after
+ *  r2 = number of MPU cycles to wait for SDRC to stabilize after
  *      reprogramming the SDRC when switching to a slower MPU speed
- * r6 = new SDRC_MR_0 register value
- * r7 = increasing SDRC rate? (1 = yes, 0 = no)
+ *  r3 = increasing SDRC rate? (1 = yes, 0 = no)
+ *
+ * Params passed via the stack. The needed params will be copied in SRAM
+ *  before use by the code in SRAM (SDRAM is not accessible during SDRC
+ *  reconfiguration):
+ *  new SDRC_RFR_CTRL_0 register contents
+ *  new SDRC_ACTIM_CTRL_A_0 register contents
+ *  new SDRC_ACTIM_CTRL_B_0 register contents
+ *  new SDRC_MR_0 register value
+ *  new SDRC_RFR_CTRL_1 register contents
+ *  new SDRC_ACTIM_CTRL_A_1 register contents
+ *  new SDRC_ACTIM_CTRL_B_1 register contents
+ *  new SDRC_MR_1 register value
  *
+ * If the param SDRC_RFR_CTRL_1 is 0, the parameters
+ *  are not programmed into the SDRC CS1 registers
  */
 ENTRY(omap3_sram_configure_core_dpll)
 	stmfd	sp!, {r1-r12, lr}	@ store regs to stack
-	ldr	r4, [sp, #52]		@ pull extra args off the stack
-	ldr	r5, [sp, #56]		@ load extra args from the stack
-	ldr	r6, [sp, #60]		@ load extra args from the stack
-	ldr	r7, [sp, #64]		@ load extra args from the stack
+
+					@ pull the extra args off the stack
+					@  and store them in SRAM
+	ldr	r4, [sp, #52]
+	str     r4, omap_sdrc_rfr_ctrl_0_val
+	ldr	r4, [sp, #56]
+	str     r4, omap_sdrc_actim_ctrl_a_0_val
+	ldr	r4, [sp, #60]
+	str     r4, omap_sdrc_actim_ctrl_b_0_val
+	ldr	r4, [sp, #64]
+	str     r4, omap_sdrc_mr_0_val
+	ldr	r4, [sp, #68]
+	str     r4, omap_sdrc_rfr_ctrl_1_val
+	cmp	r4, #0			@ if SDRC_RFR_CTRL_1 is 0,
+	beq	skip_cs1_params		@  do not use cs1 params
+	ldr	r4, [sp, #72]
+	str     r4, omap_sdrc_actim_ctrl_a_1_val
+	ldr	r4, [sp, #76]
+	str     r4, omap_sdrc_actim_ctrl_b_1_val
+	ldr	r4, [sp, #80]
+	str     r4, omap_sdrc_mr_1_val
+skip_cs1_params:
 	dsb				@ flush buffered writes to interconnect
-	cmp	r7, #1			@ if increasing SDRC clk rate,
+
+	cmp	r3, #1			@ if increasing SDRC clk rate,
 	bleq	configure_sdrc		@ program the SDRC regs early (for RFR)
-	cmp	r4, #SDRC_UNLOCK_DLL	@ set the intended DLL state
+	cmp	r1, #SDRC_UNLOCK_DLL	@ set the intended DLL state
 	bleq	unlock_dll
 	blne	lock_dll
 	bl	sdram_in_selfrefresh	@ put SDRAM in self refresh, idle SDRC
 	bl 	configure_core_dpll	@ change the DPLL3 M2 divider
 	bl	enable_sdrc		@ take SDRC out of idle
-	cmp	r4, #SDRC_UNLOCK_DLL	@ wait for DLL status to change
+	cmp	r1, #SDRC_UNLOCK_DLL	@ wait for DLL status to change
 	bleq	wait_dll_unlock
 	blne	wait_dll_lock
-	cmp	r7, #1			@ if increasing SDRC clk rate,
+	cmp	r3, #1			@ if increasing SDRC clk rate,
 	beq	return_to_sdram		@ return to SDRAM code, otherwise,
 	bl	configure_sdrc		@ reprogram SDRC regs now
-	mov	r12, r5
+	mov	r12, r2
 	bl	wait_clk_stable		@ wait for SDRC to stabilize
 return_to_sdram:
 	isb				@ prevent speculative exec past here
@@ -149,7 +180,7 @@ configure_core_dpll:
 	ldr	r12, [r11]
 	ldr	r10, core_m2_mask_val	@ modify m2 for core dpll
 	and	r12, r12, r10
-	orr	r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
+	orr	r12, r12, r0, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
 	str	r12, [r11]
 	ldr	r12, [r11]		@ posted-write barrier for CM
 	bx	lr
@@ -187,15 +218,34 @@ wait_dll_unlock:
 	bne	wait_dll_unlock
 	bx	lr
 configure_sdrc:
-	ldr	r11, omap3_sdrc_rfr_ctrl
-	str	r0, [r11]
-	ldr	r11, omap3_sdrc_actim_ctrla
-	str	r1, [r11]
-	ldr	r11, omap3_sdrc_actim_ctrlb
-	str	r2, [r11]
+	ldr	r12, omap_sdrc_rfr_ctrl_0_val	@ fetch value from SRAM
+	ldr	r11, omap3_sdrc_rfr_ctrl_0	@ fetch addr from SRAM
+	str	r12, [r11]			@ store
+	ldr	r12, omap_sdrc_actim_ctrl_a_0_val
+	ldr	r11, omap3_sdrc_actim_ctrl_a_0
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_actim_ctrl_b_0_val
+	ldr	r11, omap3_sdrc_actim_ctrl_b_0
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_mr_0_val
 	ldr	r11, omap3_sdrc_mr_0
-	str	r6, [r11]
-	ldr	r6, [r11]		@ posted-write barrier for SDRC
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_rfr_ctrl_1_val
+	cmp	r12, #0			@ if SDRC_RFR_CTRL_1 is 0,
+	beq	skip_cs1_prog		@  do not program cs1 params
+	ldr	r11, omap3_sdrc_rfr_ctrl_1
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_actim_ctrl_a_1_val
+	ldr	r11, omap3_sdrc_actim_ctrl_a_1
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_actim_ctrl_b_1_val
+	ldr	r11, omap3_sdrc_actim_ctrl_b_1
+	str	r12, [r11]
+	ldr	r12, omap_sdrc_mr_1_val
+	ldr	r11, omap3_sdrc_mr_1
+	str	r12, [r11]
+skip_cs1_prog:
+	ldr	r12, [r11]		@ posted-write barrier for SDRC
 	bx	lr
 
 omap3_sdrc_power:
@@ -206,14 +256,40 @@ omap3_cm_idlest1_core:
 	.word OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST)
 omap3_cm_iclken1_core:
 	.word OMAP34XX_CM_REGADDR(CORE_MOD, CM_ICLKEN1)
-omap3_sdrc_rfr_ctrl:
+
+omap3_sdrc_rfr_ctrl_0:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_0)
-omap3_sdrc_actim_ctrla:
+omap3_sdrc_rfr_ctrl_1:
+	.word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_1)
+omap3_sdrc_actim_ctrl_a_0:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0)
-omap3_sdrc_actim_ctrlb:
+omap3_sdrc_actim_ctrl_a_1:
+	.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_1)
+omap3_sdrc_actim_ctrl_b_0:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0)
+omap3_sdrc_actim_ctrl_b_1:
+	.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_1)
 omap3_sdrc_mr_0:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_MR_0)
+omap3_sdrc_mr_1:
+	.word OMAP34XX_SDRC_REGADDR(SDRC_MR_1)
+omap_sdrc_rfr_ctrl_0_val:
+	.word 0xDEADBEEF
+omap_sdrc_rfr_ctrl_1_val:
+	.word 0xDEADBEEF
+omap_sdrc_actim_ctrl_a_0_val:
+	.word 0xDEADBEEF
+omap_sdrc_actim_ctrl_a_1_val:
+	.word 0xDEADBEEF
+omap_sdrc_actim_ctrl_b_0_val:
+	.word 0xDEADBEEF
+omap_sdrc_actim_ctrl_b_1_val:
+	.word 0xDEADBEEF
+omap_sdrc_mr_0_val:
+	.word 0xDEADBEEF
+omap_sdrc_mr_1_val:
+	.word 0xDEADBEEF
+
 omap3_sdrc_dlla_status:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS)
 omap3_sdrc_dlla_ctrl:
@@ -223,3 +299,4 @@ core_m2_mask_val:
 
 ENTRY(omap3_sram_configure_core_dpll_sz)
 	.word	. - omap3_sram_configure_core_dpll
+
diff --git a/arch/arm/plat-omap/include/mach/io.h b/arch/arm/plat-omap/include/mach/io.h
index 73f483d56ca..21fb0efdda8 100644
--- a/arch/arm/plat-omap/include/mach/io.h
+++ b/arch/arm/plat-omap/include/mach/io.h
@@ -228,7 +228,8 @@ extern void omap1_map_common_io(void);
 extern void omap1_init_common_hw(void);
 
 extern void omap2_map_common_io(void);
-extern void omap2_init_common_hw(struct omap_sdrc_params *sp);
+extern void omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
+				 struct omap_sdrc_params *sdrc_cs1);
 
 #define __arch_ioremap(p,s,t)	omap_ioremap(p,s,t)
 #define __arch_iounmap(v)	omap_iounmap(v)
diff --git a/arch/arm/plat-omap/include/mach/sdrc.h b/arch/arm/plat-omap/include/mach/sdrc.h
index adc73522491..0be18e4ff18 100644
--- a/arch/arm/plat-omap/include/mach/sdrc.h
+++ b/arch/arm/plat-omap/include/mach/sdrc.h
@@ -30,6 +30,10 @@
 #define SDRC_ACTIM_CTRL_A_0	0x09c
 #define SDRC_ACTIM_CTRL_B_0	0x0a0
 #define SDRC_RFR_CTRL_0		0x0a4
+#define SDRC_MR_1		0x0B4
+#define SDRC_ACTIM_CTRL_A_1	0x0C4
+#define SDRC_ACTIM_CTRL_B_1	0x0C8
+#define SDRC_RFR_CTRL_1		0x0D4
 
 /*
  * These values represent the number of memory clock cycles between
@@ -102,8 +106,11 @@ struct omap_sdrc_params {
 	u32 mr;
 };
 
-void __init omap2_sdrc_init(struct omap_sdrc_params *sp);
-struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r);
+void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
+			    struct omap_sdrc_params *sdrc_cs1);
+int omap2_sdrc_get_params(unsigned long r,
+			  struct omap_sdrc_params **sdrc_cs0,
+			  struct omap_sdrc_params **sdrc_cs1);
 
 #ifdef CONFIG_ARCH_OMAP2
 
diff --git a/arch/arm/plat-omap/include/mach/sram.h b/arch/arm/plat-omap/include/mach/sram.h
index 4d53cc59d7a..8974e3fc269 100644
--- a/arch/arm/plat-omap/include/mach/sram.h
+++ b/arch/arm/plat-omap/include/mach/sram.h
@@ -21,11 +21,12 @@ extern void omap2_sram_reprogram_sdrc(u32 perf_level, u32 dll_val,
 				      u32 mem_type);
 extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass);
 
-extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl,
-				     u32 sdrc_actim_ctrla,
-				     u32 sdrc_actim_ctrlb, u32 m2,
-				     u32 unlock_dll, u32 f, u32 sdrc_mr,
-				     u32 inc);
+extern u32 omap3_configure_core_dpll(
+			u32 m2, u32 unlock_dll, u32 f, u32 inc,
+			u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+			u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+			u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+			u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
 
 /* Do not use these */
 extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl);
@@ -59,12 +60,12 @@ extern void omap243x_sram_reprogram_sdrc(u32 perf_level, u32 dll_val,
 						u32 mem_type);
 extern unsigned long omap243x_sram_reprogram_sdrc_sz;
 
-
-extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl,
-					  u32 sdrc_actim_ctrla,
-					  u32 sdrc_actim_ctrlb, u32 m2,
-					  u32 unlock_dll, u32 f, u32 sdrc_mr,
-					  u32 inc);
+extern u32 omap3_sram_configure_core_dpll(
+			u32 m2, u32 unlock_dll, u32 f, u32 inc,
+			u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+			u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+			u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+			u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
 extern unsigned long omap3_sram_configure_core_dpll_sz;
 
 #endif
diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
index 4ea73804d21..4e781c99f0e 100644
--- a/arch/arm/plat-omap/sram.c
+++ b/arch/arm/plat-omap/sram.c
@@ -373,20 +373,26 @@ static inline int omap243x_sram_init(void)
 
 #ifdef CONFIG_ARCH_OMAP3
 
-static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl,
-					      u32 sdrc_actim_ctrla,
-					      u32 sdrc_actim_ctrlb,
-					      u32 m2, u32 unlock_dll,
-					      u32 f, u32 sdrc_mr, u32 inc);
-u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla,
-			      u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll,
-			      u32 f, u32 sdrc_mr, u32 inc)
+static u32 (*_omap3_sram_configure_core_dpll)(
+			u32 m2, u32 unlock_dll, u32 f, u32 inc,
+			u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+			u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+			u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+			u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
+
+u32 omap3_configure_core_dpll(u32 m2, u32 unlock_dll, u32 f, u32 inc,
+			u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+			u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+			u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+			u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1)
 {
 	BUG_ON(!_omap3_sram_configure_core_dpll);
-	return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl,
-					       sdrc_actim_ctrla,
-					       sdrc_actim_ctrlb, m2,
-					       unlock_dll, f, sdrc_mr, inc);
+	return _omap3_sram_configure_core_dpll(
+			m2, unlock_dll, f, inc,
+			sdrc_rfr_ctrl_0, sdrc_actim_ctrl_a_0,
+			sdrc_actim_ctrl_b_0, sdrc_mr_0,
+			sdrc_rfr_ctrl_1, sdrc_actim_ctrl_a_1,
+			sdrc_actim_ctrl_b_1, sdrc_mr_1);
 }
 
 /* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */
-- 
GitLab


From 9fb97412c3be5d0d1dd0e9d7c5268469e4c942aa Mon Sep 17 00:00:00 2001
From: Jean Pihet <jpihet@mvista.com>
Date: Fri, 24 Jul 2009 19:43:25 -0600
Subject: [PATCH 0096/1153] OMAP3: Setup MUX settings for SDRC CKE signals

This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.

A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.

Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/mach-omap2/board-omap3beagle.c  | 4 ++++
 arch/arm/mach-omap2/board-omap3pandora.c | 5 +++++
 arch/arm/mach-omap2/board-overo.c        | 5 +++++
 arch/arm/mach-omap2/board-rx51.c         | 4 ++++
 arch/arm/mach-omap2/mux.c                | 6 ++++++
 arch/arm/plat-omap/include/mach/mux.h    | 4 ++++
 6 files changed, 28 insertions(+)

diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 4abefd9566e..e00ba128cec 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -409,6 +409,10 @@ static void __init omap3_beagle_init(void)
 
 	usb_musb_init();
 	omap3beagle_flash_init();
+
+	/* Ensure SDRC pins are mux'd for self-refresh */
+	omap_cfg_reg(H16_34XX_SDRC_CKE0);
+	omap_cfg_reg(H17_34XX_SDRC_CKE1);
 }
 
 static void __init omap3_beagle_map_io(void)
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 9b991ced382..864ee3d021f 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -40,6 +40,7 @@
 #include <mach/mcspi.h>
 #include <mach/usb.h>
 #include <mach/keypad.h>
+#include <mach/mux.h>
 
 #include "sdram-micron-mt46h32m32lf-6.h"
 #include "mmc-twl4030.h"
@@ -398,6 +399,10 @@ static void __init omap3pandora_init(void)
 	omap3pandora_ads7846_init();
 	pandora_keys_gpio_init();
 	usb_musb_init();
+
+	/* Ensure SDRC pins are mux'd for self-refresh */
+	omap_cfg_reg(H16_34XX_SDRC_CKE0);
+	omap_cfg_reg(H17_34XX_SDRC_CKE1);
 }
 
 static void __init omap3pandora_map_io(void)
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index 44bc1c54cd0..6b171b338ec 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -44,6 +44,7 @@
 #include <mach/gpmc.h>
 #include <mach/hardware.h>
 #include <mach/nand.h>
+#include <mach/mux.h>
 #include <mach/usb.h>
 
 #include "sdram-micron-mt46h32m32lf-6.h"
@@ -396,6 +397,10 @@ static void __init overo_init(void)
 	overo_ads7846_init();
 	overo_init_smsc911x();
 
+	/* Ensure SDRC pins are mux'd for self-refresh */
+	omap_cfg_reg(H16_34XX_SDRC_CKE0);
+	omap_cfg_reg(H17_34XX_SDRC_CKE1);
+
 	if ((gpio_request(OVERO_GPIO_W2W_NRESET,
 			  "OVERO_GPIO_W2W_NRESET") == 0) &&
 	    (gpio_direction_output(OVERO_GPIO_W2W_NRESET, 1) == 0)) {
diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c
index 591ae8a5805..1c9e07fe826 100644
--- a/arch/arm/mach-omap2/board-rx51.c
+++ b/arch/arm/mach-omap2/board-rx51.c
@@ -75,6 +75,10 @@ static void __init rx51_init(void)
 	omap_serial_init();
 	usb_musb_init();
 	rx51_peripherals_init();
+
+	/* Ensure SDRC pins are mux'd for self-refresh */
+	omap_cfg_reg(H16_34XX_SDRC_CKE0);
+	omap_cfg_reg(H17_34XX_SDRC_CKE1);
 }
 
 static void __init rx51_map_io(void)
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index 026c4fc883a..43d6b92b65f 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -486,6 +486,12 @@ MUX_CFG_34XX("H19_34XX_GPIO164_OUT", 0x19c,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
 MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+
+/* OMAP3 SDRC CKE signals to SDR/DDR ram chips */
+MUX_CFG_34XX("H16_34XX_SDRC_CKE0", 0x262,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
+MUX_CFG_34XX("H17_34XX_SDRC_CKE1", 0x264,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
 };
 
 #define OMAP34XX_PINS_SZ	ARRAY_SIZE(omap34xx_pins)
diff --git a/arch/arm/plat-omap/include/mach/mux.h b/arch/arm/plat-omap/include/mach/mux.h
index 85a62170576..80281c458ba 100644
--- a/arch/arm/plat-omap/include/mach/mux.h
+++ b/arch/arm/plat-omap/include/mach/mux.h
@@ -853,6 +853,10 @@ enum omap34xx_index {
 	AE5_34XX_GPIO143,
 	H19_34XX_GPIO164_OUT,
 	J25_34XX_GPIO170,
+
+	/* OMAP3 SDRC CKE signals to SDR/DDR ram chips */
+	H16_34XX_SDRC_CKE0,
+	H17_34XX_SDRC_CKE1,
 };
 
 struct omap_mux_cfg {
-- 
GitLab


From 75f251e3d0803b028f3474fdc75be0994c377ab5 Mon Sep 17 00:00:00 2001
From: Paul Walmsley <paul@pwsan.com>
Date: Fri, 24 Jul 2009 19:44:01 -0600
Subject: [PATCH 0097/1153] OMAP2/3 SDRC: don't set SDRC_POWER.PWDENA on boot

Stop setting SDRC_POWER.PWDENA on boot.  There is a nasty erratum
(34xx erratum 1.150) that can cause memory corruption if PWDENA is
enabled.

Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>.

Tested on BeagleBoard rev C2.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
---
 arch/arm/mach-omap2/sdrc.c     | 5 ++++-
 arch/arm/mach-omap2/sram34xx.S | 2 --
 2 files changed, 4 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-omap2/sdrc.c b/arch/arm/mach-omap2/sdrc.c
index 2e9e38db30e..9e3bd4fa781 100644
--- a/arch/arm/mach-omap2/sdrc.c
+++ b/arch/arm/mach-omap2/sdrc.c
@@ -125,8 +125,11 @@ void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
 	sdrc_init_params_cs1 = sdrc_cs1;
 
 	/* XXX Enable SRFRONIDLEREQ here also? */
+	/*
+	 * PWDENA should not be set due to 34xx erratum 1.150 - PWDENA
+	 * can cause random memory corruption
+	 */
 	l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) |
-		(1 << SDRC_POWER_PWDENA_SHIFT) |
 		(1 << SDRC_POWER_PAGEPOLICY_SHIFT);
 	sdrc_write_reg(l, SDRC_POWER);
 }
diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S
index 3aef7448b2a..9c2d0465a83 100644
--- a/arch/arm/mach-omap2/sram34xx.S
+++ b/arch/arm/mach-omap2/sram34xx.S
@@ -58,7 +58,6 @@
 
 /* SDRC_POWER bit settings */
 #define SRFRONIDLEREQ_MASK		0x40
-#define PWDENA_MASK			0x4
 
 /* CM_IDLEST1_CORE bit settings */
 #define ST_SDRC_MASK			0x2
@@ -160,7 +159,6 @@ sdram_in_selfrefresh:
 	ldr	r12, [r11]		@ read the contents of SDRC_POWER
 	mov	r9, r12			@ keep a copy of SDRC_POWER bits
 	orr 	r12, r12, #SRFRONIDLEREQ_MASK	@ enable self refresh on idle
-	bic 	r12, r12, #PWDENA_MASK	@ clear PWDENA
 	str 	r12, [r11]		@ write back to SDRC_POWER register
 	ldr	r12, [r11]		@ posted-write barrier for SDRC
 idle_sdrc:
-- 
GitLab


From 8ff120e5303e27e03aba7b774e86fd43eaf90376 Mon Sep 17 00:00:00 2001
From: Rajendra Nayak <rnayak@ti.com>
Date: Fri, 24 Jul 2009 19:44:01 -0600
Subject: [PATCH 0098/1153] OMAP3 SDRC: Fix freeze when scaling CORE dpll to <
 83Mhz

This patch fixes a bug in the CORE dpll scaling sequence which was
errouneously clearing some bits in the SDRC DLLA CTRL register and
hence causing a freeze.  The issue was observed only on platforms
which scale CORE dpll to < 83Mhz and hence program the DLL in fixed
delay mode.

Issue reported by Limei Wang <E12499@motorola.com>, with debugging
assistance from Richard Woodruff <r-woodruff2@ti.com> and Girish
Ghongdemath <girishsg@ti.com>.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Limei Wang <E12499@motorola.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Girish Ghongdemath <girishsg@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated patch description to include collaboration credits]
---
 arch/arm/mach-omap2/sram34xx.S | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S
index 9c2d0465a83..e6b112590d7 100644
--- a/arch/arm/mach-omap2/sram34xx.S
+++ b/arch/arm/mach-omap2/sram34xx.S
@@ -143,7 +143,7 @@ return_to_sdram:
 unlock_dll:
 	ldr	r11, omap3_sdrc_dlla_ctrl
 	ldr	r12, [r11]
-	and	r12, r12, #FIXEDDELAY_MASK
+	bic	r12, r12, #FIXEDDELAY_MASK
 	orr	r12, r12, #FIXEDDELAY_DEFAULT
 	orr	r12, r12, #DLLIDLE_MASK
 	str	r12, [r11]		@ (no OCP barrier needed)
-- 
GitLab


From df56556e571234cf26072cd58c01ac3520986b44 Mon Sep 17 00:00:00 2001
From: Rajendra Nayak <rnayak@ti.com>
Date: Fri, 24 Jul 2009 19:44:02 -0600
Subject: [PATCH 0099/1153] OMAP3 SDRC: Move the clk stabilization delay to the
 right place

The clock stabilization delay post a M2 divider change is needed
even before a SDRC interface clock re-enable and not only before
jumping back to SDRAM.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/mach-omap2/sram34xx.S | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S
index e6b112590d7..82aa4a3d160 100644
--- a/arch/arm/mach-omap2/sram34xx.S
+++ b/arch/arm/mach-omap2/sram34xx.S
@@ -127,6 +127,8 @@ skip_cs1_params:
 	blne	lock_dll
 	bl	sdram_in_selfrefresh	@ put SDRAM in self refresh, idle SDRC
 	bl 	configure_core_dpll	@ change the DPLL3 M2 divider
+	mov	r12, r2
+	bl	wait_clk_stable		@ wait for SDRC to stabilize
 	bl	enable_sdrc		@ take SDRC out of idle
 	cmp	r1, #SDRC_UNLOCK_DLL	@ wait for DLL status to change
 	bleq	wait_dll_unlock
@@ -134,8 +136,6 @@ skip_cs1_params:
 	cmp	r3, #1			@ if increasing SDRC clk rate,
 	beq	return_to_sdram		@ return to SDRAM code, otherwise,
 	bl	configure_sdrc		@ reprogram SDRC regs now
-	mov	r12, r2
-	bl	wait_clk_stable		@ wait for SDRC to stabilize
 return_to_sdram:
 	isb				@ prevent speculative exec past here
 	mov 	r0, #0 			@ return value
-- 
GitLab


From 72350b29a4c0debfc27c2edbeed9b4ff3f935dd4 Mon Sep 17 00:00:00 2001
From: Paul Walmsley <paul@pwsan.com>
Date: Fri, 24 Jul 2009 19:44:03 -0600
Subject: [PATCH 0100/1153] OMAP2/3 clock: split, rename
 omap2_wait_clock_ready()

Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not
handled by the current omap2_wait_clock_ready() code.  In preparation
for patches that fix the unusual devices, rename the function
omap2_wait_clock_ready() to omap2_wait_module_ready() and split it
into three parts:

1. A clkops-specific companion clock return function (by default,
   omap2_clk_dflt_find_companion())

2. A clkops-specific CM_IDLEST register address and bit shift return
   function (by default, omap2_clk_dflt_find_idlest())

3. Code to wait for the CM to indicate that the module is ready
   (omap2_cm_wait_idlest())

Clocks can now specify their own custom find_companion() and find_idlest()
functions; used in subsequent patches.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/mach-omap2/clock.c             | 156 ++++++++++++------------
 arch/arm/mach-omap2/clock.h             |   6 +
 arch/arm/mach-omap2/prcm.c              |  43 +++++++
 arch/arm/plat-omap/include/mach/clock.h |   2 +
 arch/arm/plat-omap/include/mach/prcm.h  |   1 +
 5 files changed, 131 insertions(+), 77 deletions(-)

diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c
index b0665f161c0..456e2ad5f62 100644
--- a/arch/arm/mach-omap2/clock.c
+++ b/arch/arm/mach-omap2/clock.c
@@ -27,6 +27,7 @@
 #include <mach/clock.h>
 #include <mach/clockdomain.h>
 #include <mach/cpu.h>
+#include <mach/prcm.h>
 #include <asm/div64.h>
 
 #include <mach/sdrc.h>
@@ -38,8 +39,6 @@
 #include "cm-regbits-24xx.h"
 #include "cm-regbits-34xx.h"
 
-#define MAX_CLOCK_ENABLE_WAIT		100000
-
 /* DPLL rate rounding: minimum DPLL multiplier, divider values */
 #define DPLL_MIN_MULTIPLIER		1
 #define DPLL_MIN_DIVIDER		1
@@ -274,83 +273,97 @@ unsigned long omap2_fixed_divisor_recalc(struct clk *clk)
 }
 
 /**
- * omap2_wait_clock_ready - wait for clock to enable
- * @reg: physical address of clock IDLEST register
- * @mask: value to mask against to determine if the clock is active
- * @name: name of the clock (for printk)
+ * omap2_clk_dflt_find_companion - find companion clock to @clk
+ * @clk: struct clk * to find the companion clock of
+ * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in
+ * @other_bit: u8 ** to return the companion clock bit shift in
+ *
+ * Note: We don't need special code here for INVERT_ENABLE for the
+ * time being since INVERT_ENABLE only applies to clocks enabled by
+ * CM_CLKEN_PLL
  *
- * Returns 1 if the clock enabled in time, or 0 if it failed to enable
- * in roughly MAX_CLOCK_ENABLE_WAIT microseconds.
+ * Convert CM_ICLKEN* <-> CM_FCLKEN*.  This conversion assumes it's
+ * just a matter of XORing the bits.
+ *
+ * Some clocks don't have companion clocks.  For example, modules with
+ * only an interface clock (such as MAILBOXES) don't have a companion
+ * clock.  Right now, this code relies on the hardware exporting a bit
+ * in the correct companion register that indicates that the
+ * nonexistent 'companion clock' is active.  Future patches will
+ * associate this type of code with per-module data structures to
+ * avoid this issue, and remove the casts.  No return value.
  */
-int omap2_wait_clock_ready(void __iomem *reg, u32 mask, const char *name)
+void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
+				   u8 *other_bit)
 {
-	int i = 0;
-	int ena = 0;
+	u32 r;
 
 	/*
-	 * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
-	 * 34xx reverses this, just to keep us on our toes
+	 * Convert CM_ICLKEN* <-> CM_FCLKEN*.  This conversion assumes
+	 * it's just a matter of XORing the bits.
 	 */
-	if (cpu_mask & (RATE_IN_242X | RATE_IN_243X))
-		ena = mask;
-	else if (cpu_mask & RATE_IN_343X)
-		ena = 0;
-
-	/* Wait for lock */
-	while (((__raw_readl(reg) & mask) != ena) &&
-	       (i++ < MAX_CLOCK_ENABLE_WAIT)) {
-		udelay(1);
-	}
-
-	if (i <= MAX_CLOCK_ENABLE_WAIT)
-		pr_debug("Clock %s stable after %d loops\n", name, i);
-	else
-		printk(KERN_ERR "Clock %s didn't enable in %d tries\n",
-		       name, MAX_CLOCK_ENABLE_WAIT);
-
-
-	return (i < MAX_CLOCK_ENABLE_WAIT) ? 1 : 0;
-};
+	r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN));
 
+	*other_reg = (__force void __iomem *)r;
+	*other_bit = clk->enable_bit;
+}
 
-/*
- * Note: We don't need special code here for INVERT_ENABLE
- * for the time being since INVERT_ENABLE only applies to clocks enabled by
- * CM_CLKEN_PLL
+/**
+ * omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk
+ * @clk: struct clk * to find IDLEST info for
+ * @idlest_reg: void __iomem ** to return the CM_IDLEST va in
+ * @idlest_bit: u8 ** to return the CM_IDLEST bit shift in
+ *
+ * Return the CM_IDLEST register address and bit shift corresponding
+ * to the module that "owns" this clock.  This default code assumes
+ * that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that
+ * the IDLEST register address ID corresponds to the CM_*CLKEN
+ * register address ID (e.g., that CM_FCLKEN2 corresponds to
+ * CM_IDLEST2).  This is not true for all modules.  No return value.
  */
-static void omap2_clk_wait_ready(struct clk *clk)
+void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
+				u8 *idlest_bit)
 {
-	void __iomem *reg, *other_reg, *st_reg;
-	u32 bit;
+	u32 r;
 
-	/*
-	 * REVISIT: This code is pretty ugly.  It would be nice to generalize
-	 * it and pull it into struct clk itself somehow.
-	 */
-	reg = clk->enable_reg;
+	r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+	*idlest_reg = (__force void __iomem *)r;
+	*idlest_bit = clk->enable_bit;
+}
 
-	/*
-	 * Convert CM_ICLKEN* <-> CM_FCLKEN*.  This conversion assumes
-	 * it's just a matter of XORing the bits.
-	 */
-	other_reg = (void __iomem *)((u32)reg ^ (CM_FCLKEN ^ CM_ICLKEN));
+/**
+ * omap2_module_wait_ready - wait for an OMAP module to leave IDLE
+ * @clk: struct clk * belonging to the module
+ *
+ * If the necessary clocks for the OMAP hardware IP block that
+ * corresponds to clock @clk are enabled, then wait for the module to
+ * indicate readiness (i.e., to leave IDLE).  This code does not
+ * belong in the clock code and will be moved in the medium term to
+ * module-dependent code.  No return value.
+ */
+static void omap2_module_wait_ready(struct clk *clk)
+{
+	void __iomem *companion_reg, *idlest_reg;
+	u8 other_bit, idlest_bit;
+
+	/* Not all modules have multiple clocks that their IDLEST depends on */
+	if (clk->ops->find_companion) {
+		clk->ops->find_companion(clk, &companion_reg, &other_bit);
+		if (!(__raw_readl(companion_reg) & (1 << other_bit)))
+			return;
+	}
 
-	/* Check if both functional and interface clocks
-	 * are running. */
-	bit = 1 << clk->enable_bit;
-	if (!(__raw_readl(other_reg) & bit))
-		return;
-	st_reg = (void __iomem *)(((u32)other_reg & ~0xf0) | 0x20); /* CM_IDLEST* */
+	clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit);
 
-	omap2_wait_clock_ready(st_reg, bit, clk->name);
+	omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), clk->name);
 }
 
-static int omap2_dflt_clk_enable(struct clk *clk)
+int omap2_dflt_clk_enable(struct clk *clk)
 {
 	u32 v;
 
 	if (unlikely(clk->enable_reg == NULL)) {
-		printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
+		pr_err("clock.c: Enable for %s without enable code\n",
 		       clk->name);
 		return 0; /* REVISIT: -EINVAL */
 	}
@@ -363,26 +376,13 @@ static int omap2_dflt_clk_enable(struct clk *clk)
 	__raw_writel(v, clk->enable_reg);
 	v = __raw_readl(clk->enable_reg); /* OCP barrier */
 
-	return 0;
-}
+	if (clk->ops->find_idlest)
+		omap2_module_wait_ready(clk);
 
-static int omap2_dflt_clk_enable_wait(struct clk *clk)
-{
-	int ret;
-
-	if (!clk->enable_reg) {
-		printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
-		       clk->name);
-		return 0; /* REVISIT: -EINVAL */
-	}
-
-	ret = omap2_dflt_clk_enable(clk);
-	if (ret == 0)
-		omap2_clk_wait_ready(clk);
-	return ret;
+	return 0;
 }
 
-static void omap2_dflt_clk_disable(struct clk *clk)
+void omap2_dflt_clk_disable(struct clk *clk)
 {
 	u32 v;
 
@@ -406,8 +406,10 @@ static void omap2_dflt_clk_disable(struct clk *clk)
 }
 
 const struct clkops clkops_omap2_dflt_wait = {
-	.enable		= omap2_dflt_clk_enable_wait,
+	.enable		= omap2_dflt_clk_enable,
 	.disable	= omap2_dflt_clk_disable,
+	.find_companion	= omap2_clk_dflt_find_companion,
+	.find_idlest	= omap2_clk_dflt_find_idlest,
 };
 
 const struct clkops clkops_omap2_dflt = {
diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h
index 2679ddfa642..9ae7540f8af 100644
--- a/arch/arm/mach-omap2/clock.h
+++ b/arch/arm/mach-omap2/clock.h
@@ -65,6 +65,12 @@ int omap2_clksel_set_rate(struct clk *clk, unsigned long rate);
 u32 omap2_get_dpll_rate(struct clk *clk);
 int omap2_wait_clock_ready(void __iomem *reg, u32 cval, const char *name);
 void omap2_clk_prepare_for_reboot(void);
+int omap2_dflt_clk_enable(struct clk *clk);
+void omap2_dflt_clk_disable(struct clk *clk);
+void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
+				   u8 *other_bit);
+void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
+				u8 *idlest_bit);
 
 extern const struct clkops clkops_omap2_dflt_wait;
 extern const struct clkops clkops_omap2_dflt;
diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c
index f945156d558..ced555a4cd1 100644
--- a/arch/arm/mach-omap2/prcm.c
+++ b/arch/arm/mach-omap2/prcm.c
@@ -17,6 +17,7 @@
 #include <linux/init.h>
 #include <linux/clk.h>
 #include <linux/io.h>
+#include <linux/delay.h>
 
 #include <mach/common.h>
 #include <mach/prcm.h>
@@ -28,6 +29,8 @@
 static void __iomem *prm_base;
 static void __iomem *cm_base;
 
+#define MAX_MODULE_ENABLE_WAIT		100000
+
 u32 omap_prcm_get_reset_sources(void)
 {
 	/* XXX This presumably needs modification for 34XX */
@@ -120,6 +123,46 @@ u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx)
 }
 EXPORT_SYMBOL(cm_rmw_mod_reg_bits);
 
+/**
+ * omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
+ * @reg: physical address of module IDLEST register
+ * @mask: value to mask against to determine if the module is active
+ * @name: name of the clock (for printk)
+ *
+ * Returns 1 if the module indicated readiness in time, or 0 if it
+ * failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds.
+ */
+int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name)
+{
+	int i = 0;
+	int ena = 0;
+
+	/*
+	 * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
+	 * 34xx reverses this, just to keep us on our toes
+	 */
+	if (cpu_is_omap24xx())
+		ena = mask;
+	else if (cpu_is_omap34xx())
+		ena = 0;
+	else
+		BUG();
+
+	/* Wait for lock */
+	while (((__raw_readl(reg) & mask) != ena) &&
+	       (i++ < MAX_MODULE_ENABLE_WAIT))
+		udelay(1);
+
+	if (i < MAX_MODULE_ENABLE_WAIT)
+		pr_debug("cm: Module associated with clock %s ready after %d "
+			 "loops\n", name, i);
+	else
+		pr_err("cm: Module associated with clock %s didn't enable in "
+		       "%d tries\n", name, MAX_MODULE_ENABLE_WAIT);
+
+	return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0;
+};
+
 void __init omap2_set_globals_prcm(struct omap_globals *omap2_globals)
 {
 	prm_base = omap2_globals->prm;
diff --git a/arch/arm/plat-omap/include/mach/clock.h b/arch/arm/plat-omap/include/mach/clock.h
index f9f65e1ba3f..4b8b0d65cbf 100644
--- a/arch/arm/plat-omap/include/mach/clock.h
+++ b/arch/arm/plat-omap/include/mach/clock.h
@@ -20,6 +20,8 @@ struct clockdomain;
 struct clkops {
 	int			(*enable)(struct clk *);
 	void			(*disable)(struct clk *);
+	void			(*find_idlest)(struct clk *, void __iomem **, u8 *);
+	void			(*find_companion)(struct clk *, void __iomem **, u8 *);
 };
 
 #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \
diff --git a/arch/arm/plat-omap/include/mach/prcm.h b/arch/arm/plat-omap/include/mach/prcm.h
index 24ac3c71591..cda2a70397b 100644
--- a/arch/arm/plat-omap/include/mach/prcm.h
+++ b/arch/arm/plat-omap/include/mach/prcm.h
@@ -25,6 +25,7 @@
 
 u32 omap_prcm_get_reset_sources(void);
 void omap_prcm_arch_reset(char mode);
+int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name);
 
 #endif
 
-- 
GitLab


From 3dc2197579089c5b74c7fba666c8ccf1a449afb4 Mon Sep 17 00:00:00 2001
From: Paul Walmsley <paul@pwsan.com>
Date: Fri, 24 Jul 2009 19:44:04 -0600
Subject: [PATCH 0101/1153] OMAP2 clock: 2430 I2CHS uses non-standard CM_IDLEST
 register

OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits
are in CM_{I,F}CLKEN2_CORE [1].  Fix by implementing a custom clkops
.find_idlest function to return the correct slave IDLEST register.

...

1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1
   (Rev. V) Technical Reference Manual, tables 4-99 and 4-105.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/mach-omap2/clock24xx.c | 37 +++++++++++++++++++++++++++++++--
 arch/arm/mach-omap2/clock24xx.h |  4 ++--
 2 files changed, 37 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-omap2/clock24xx.c b/arch/arm/mach-omap2/clock24xx.c
index 44de0271fc2..bc5d3ac6661 100644
--- a/arch/arm/mach-omap2/clock24xx.c
+++ b/arch/arm/mach-omap2/clock24xx.c
@@ -30,6 +30,7 @@
 
 #include <mach/clock.h>
 #include <mach/sram.h>
+#include <mach/prcm.h>
 #include <asm/div64.h>
 #include <asm/clkdev.h>
 
@@ -43,6 +44,18 @@
 static const struct clkops clkops_oscck;
 static const struct clkops clkops_fixed;
 
+static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
+					   void __iomem **idlest_reg,
+					   u8 *idlest_bit);
+
+/* 2430 I2CHS has non-standard IDLEST register */
+static const struct clkops clkops_omap2430_i2chs_wait = {
+	.enable		= omap2_dflt_clk_enable,
+	.disable	= omap2_dflt_clk_disable,
+	.find_idlest	= omap2430_clk_i2chs_find_idlest,
+	.find_companion = omap2_clk_dflt_find_companion,
+};
+
 #include "clock24xx.h"
 
 struct omap_clk {
@@ -239,6 +252,26 @@ static void __iomem *prcm_clksrc_ctrl;
  * Omap24xx specific clock functions
  *-------------------------------------------------------------------------*/
 
+/**
+ * omap2430_clk_i2chs_find_idlest - return CM_IDLEST info for 2430 I2CHS
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the
+ * CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE.  This custom function
+ * passes back the correct CM_IDLEST register address for I2CHS
+ * modules.  No return value.
+ */
+static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
+					   void __iomem **idlest_reg,
+					   u8 *idlest_bit)
+{
+	*idlest_reg = OMAP_CM_REGADDR(CORE_MOD, CM_IDLEST);
+	*idlest_bit = clk->enable_bit;
+}
+
+
 /**
  * omap2xxx_clk_get_core_rate - return the CORE_CLK rate
  * @clk: pointer to the combined dpll_ck + core_ck (currently "dpll_ck")
@@ -325,8 +358,8 @@ static int omap2_clk_fixed_enable(struct clk *clk)
 	else if (clk == &apll54_ck)
 		cval = OMAP24XX_ST_54M_APLL;
 
-	omap2_wait_clock_ready(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval,
-			    clk->name);
+	omap2_cm_wait_idlest(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval,
+			     clk->name);
 
 	/*
 	 * REVISIT: Should we return an error code if omap2_wait_clock_ready()
diff --git a/arch/arm/mach-omap2/clock24xx.h b/arch/arm/mach-omap2/clock24xx.h
index 458f00cdcbe..d19cf7a7d8d 100644
--- a/arch/arm/mach-omap2/clock24xx.h
+++ b/arch/arm/mach-omap2/clock24xx.h
@@ -2337,7 +2337,7 @@ static struct clk i2c2_fck = {
 
 static struct clk i2chs2_fck = {
 	.name		= "i2c_fck",
-	.ops		= &clkops_omap2_dflt_wait,
+	.ops		= &clkops_omap2430_i2chs_wait,
 	.id		= 2,
 	.parent		= &func_96m_ck,
 	.clkdm_name	= "core_l4_clkdm",
@@ -2370,7 +2370,7 @@ static struct clk i2c1_fck = {
 
 static struct clk i2chs1_fck = {
 	.name		= "i2c_fck",
-	.ops		= &clkops_omap2_dflt_wait,
+	.ops		= &clkops_omap2430_i2chs_wait,
 	.id		= 1,
 	.parent		= &func_96m_ck,
 	.clkdm_name	= "core_l4_clkdm",
-- 
GitLab


From 3c82e229f09a6acc8d24dc27c5e0e60b1d7161c2 Mon Sep 17 00:00:00 2001
From: Paul Walmsley <paul@pwsan.com>
Date: Fri, 24 Jul 2009 19:44:06 -0600
Subject: [PATCH 0102/1153] OMAP3 clock: correct module IDLEST bits: SSI; DSS;
 USBHOST; HSOTGUSB

Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS,
USBHOST, and HSOTGUSB devices.  These devices are both interconnect
initiators and targets.  Without this patch, clk_enable()s on clocks for
these modules can be very high latency (potentially up to ~200
milliseconds) and message such as the following are generated:

    Clock usbhost_48m_fck didn't enable in 100000 tries

Two bugs are fixed by this patch.  First, OMAP hardware only supports
target CM_IDLEST register bits on ES2+ chips and beyond.  ES1 chips
should not wait for these clocks to enable.  So, split the appropriate
clocks into ES1 and ES2+ variants, so that kernels running on ES1
devices won't try to wait.

Second, the current heuristic in omap2_clk_dflt_find_idlest() will
fail for these clocks.  It assumes that the CM_IDLEST bit to wait upon
is the same as the CM_*CLKEN bit, which is false[1].  Fix by
implementing custom clkops .find_idlest function pointers for the
appropriate clocks that return the correct slave IDLEST bit shift.

This was originally fixed in the linux-omap kernel during 2.6.29 in a
slightly different manner[2][3].

In the medium-term future, all of the module IDLEST code will
eventually be moved to the omap_hwmod code.

Problem reported by Jarkko Nikula <jhnikula@gmail.com>:

    http://marc.info/?l=linux-omap&m=124306184903679&w=2

...

1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the
   DSS case).

2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq.

3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html


Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
---
 arch/arm/mach-omap2/clock34xx.c | 118 ++++++++++++++++++++++++++++++--
 arch/arm/mach-omap2/clock34xx.h |  85 ++++++++++++++++++++---
 2 files changed, 185 insertions(+), 18 deletions(-)

diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c
index 1c6480d3ad6..cd7819cc0c9 100644
--- a/arch/arm/mach-omap2/clock34xx.c
+++ b/arch/arm/mach-omap2/clock34xx.c
@@ -2,7 +2,7 @@
  * OMAP3-specific clock framework functions
  *
  * Copyright (C) 2007-2008 Texas Instruments, Inc.
- * Copyright (C) 2007-2008 Nokia Corporation
+ * Copyright (C) 2007-2009 Nokia Corporation
  *
  * Written by Paul Walmsley
  * Testing and integration fixes by Jouni Högander
@@ -41,6 +41,37 @@
 
 static const struct clkops clkops_noncore_dpll_ops;
 
+static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
+					    void __iomem **idlest_reg,
+					    u8 *idlest_bit);
+static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
+					    void __iomem **idlest_reg,
+					    u8 *idlest_bit);
+static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
+						    void __iomem **idlest_reg,
+						    u8 *idlest_bit);
+
+static const struct clkops clkops_omap3430es2_ssi_wait = {
+	.enable		= omap2_dflt_clk_enable,
+	.disable	= omap2_dflt_clk_disable,
+	.find_idlest	= omap3430es2_clk_ssi_find_idlest,
+	.find_companion = omap2_clk_dflt_find_companion,
+};
+
+static const struct clkops clkops_omap3430es2_hsotgusb_wait = {
+	.enable		= omap2_dflt_clk_enable,
+	.disable	= omap2_dflt_clk_disable,
+	.find_idlest	= omap3430es2_clk_hsotgusb_find_idlest,
+	.find_companion = omap2_clk_dflt_find_companion,
+};
+
+static const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
+	.enable		= omap2_dflt_clk_enable,
+	.disable	= omap2_dflt_clk_disable,
+	.find_idlest	= omap3430es2_clk_dss_usbhost_find_idlest,
+	.find_companion = omap2_clk_dflt_find_companion,
+};
+
 #include "clock34xx.h"
 
 struct omap_clk {
@@ -157,10 +188,13 @@ static struct omap_clk omap34xx_clks[] = {
 	CLK(NULL,	"fshostusb_fck", &fshostusb_fck, CK_3430ES1),
 	CLK(NULL,	"core_12m_fck",	&core_12m_fck,	CK_343X),
 	CLK("omap_hdq.0", "fck",	&hdq_fck,	CK_343X),
-	CLK(NULL,	"ssi_ssr_fck",	&ssi_ssr_fck,	CK_343X),
-	CLK(NULL,	"ssi_sst_fck",	&ssi_sst_fck,	CK_343X),
+	CLK(NULL,	"ssi_ssr_fck",	&ssi_ssr_fck_3430es1,	CK_3430ES1),
+	CLK(NULL,	"ssi_ssr_fck",	&ssi_ssr_fck_3430es2,	CK_3430ES2),
+	CLK(NULL,	"ssi_sst_fck",	&ssi_sst_fck_3430es1,	CK_3430ES1),
+	CLK(NULL,	"ssi_sst_fck",	&ssi_sst_fck_3430es2,	CK_3430ES2),
 	CLK(NULL,	"core_l3_ick",	&core_l3_ick,	CK_343X),
-	CLK("musb_hdrc",	"ick",	&hsotgusb_ick,	CK_343X),
+	CLK("musb_hdrc",	"ick",	&hsotgusb_ick_3430es1,	CK_3430ES1),
+	CLK("musb_hdrc",	"ick",	&hsotgusb_ick_3430es2,	CK_3430ES2),
 	CLK(NULL,	"sdrc_ick",	&sdrc_ick,	CK_343X),
 	CLK(NULL,	"gpmc_fck",	&gpmc_fck,	CK_343X),
 	CLK(NULL,	"security_l3_ick", &security_l3_ick, CK_343X),
@@ -193,18 +227,21 @@ static struct omap_clk omap34xx_clks[] = {
 	CLK(NULL,	"mailboxes_ick", &mailboxes_ick, CK_343X),
 	CLK(NULL,	"omapctrl_ick",	&omapctrl_ick,	CK_343X),
 	CLK(NULL,	"ssi_l4_ick",	&ssi_l4_ick,	CK_343X),
-	CLK(NULL,	"ssi_ick",	&ssi_ick,	CK_343X),
+	CLK(NULL,	"ssi_ick",	&ssi_ick_3430es1,	CK_3430ES1),
+	CLK(NULL,	"ssi_ick",	&ssi_ick_3430es2,	CK_3430ES2),
 	CLK(NULL,	"usb_l4_ick",	&usb_l4_ick,	CK_3430ES1),
 	CLK(NULL,	"security_l4_ick2", &security_l4_ick2, CK_343X),
 	CLK(NULL,	"aes1_ick",	&aes1_ick,	CK_343X),
 	CLK("omap_rng",	"ick",		&rng_ick,	CK_343X),
 	CLK(NULL,	"sha11_ick",	&sha11_ick,	CK_343X),
 	CLK(NULL,	"des1_ick",	&des1_ick,	CK_343X),
-	CLK("omapfb",	"dss1_fck",	&dss1_alwon_fck, CK_343X),
+	CLK("omapfb",	"dss1_fck",	&dss1_alwon_fck_3430es1, CK_3430ES1),
+	CLK("omapfb",	"dss1_fck",	&dss1_alwon_fck_3430es2, CK_3430ES2),
 	CLK("omapfb",	"tv_fck",	&dss_tv_fck,	CK_343X),
 	CLK("omapfb",	"video_fck",	&dss_96m_fck,	CK_343X),
 	CLK("omapfb",	"dss2_fck",	&dss2_alwon_fck, CK_343X),
-	CLK("omapfb",	"ick",		&dss_ick,	CK_343X),
+	CLK("omapfb",	"ick",		&dss_ick_3430es1,	CK_3430ES1),
+	CLK("omapfb",	"ick",		&dss_ick_3430es2,	CK_3430ES2),
 	CLK(NULL,	"cam_mclk",	&cam_mclk,	CK_343X),
 	CLK(NULL,	"cam_ick",	&cam_ick,	CK_343X),
 	CLK(NULL,	"csi2_96m_fck",	&csi2_96m_fck,	CK_343X),
@@ -300,6 +337,73 @@ static struct omap_clk omap34xx_clks[] = {
  */
 #define SDRC_MPURATE_LOOPS		96
 
+/**
+ * omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift
+ * from the CM_{I,F}CLKEN bit.  Pass back the correct info via
+ * @idlest_reg and @idlest_bit.  No return value.
+ */
+static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
+					    void __iomem **idlest_reg,
+					    u8 *idlest_bit)
+{
+	u32 r;
+
+	r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+	*idlest_reg = (__force void __iomem *)r;
+	*idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT;
+}
+
+/**
+ * omap3430es2_clk_dss_usbhost_find_idlest - CM_IDLEST info for DSS, USBHOST
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * Some OMAP modules on OMAP3 ES2+ chips have both initiator and
+ * target IDLEST bits.  For our purposes, we are concerned with the
+ * target IDLEST bits, which exist at a different bit position than
+ * the *CLKEN bit position for these modules (DSS and USBHOST) (The
+ * default find_idlest code assumes that they are at the same
+ * position.)  No return value.
+ */
+static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
+						    void __iomem **idlest_reg,
+						    u8 *idlest_bit)
+{
+	u32 r;
+
+	r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+	*idlest_reg = (__force void __iomem *)r;
+	/* USBHOST_IDLE has same shift */
+	*idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT;
+}
+
+/**
+ * omap3430es2_clk_hsotgusb_find_idlest - return CM_IDLEST info for HSOTGUSB
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different
+ * shift from the CM_{I,F}CLKEN bit.  Pass back the correct info via
+ * @idlest_reg and @idlest_bit.  No return value.
+ */
+static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
+						 void __iomem **idlest_reg,
+						 u8 *idlest_bit)
+{
+	u32 r;
+
+	r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+	*idlest_reg = (__force void __iomem *)r;
+	*idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT;
+}
+
 /**
  * omap3_dpll_recalc - recalculate DPLL rate
  * @clk: DPLL struct clk
diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h
index e433aec4efd..57cc2725b92 100644
--- a/arch/arm/mach-omap2/clock34xx.h
+++ b/arch/arm/mach-omap2/clock34xx.h
@@ -1568,7 +1568,7 @@ static const struct clksel ssi_ssr_clksel[] = {
 	{ .parent = NULL }
 };
 
-static struct clk ssi_ssr_fck = {
+static struct clk ssi_ssr_fck_3430es1 = {
 	.name		= "ssi_ssr_fck",
 	.ops		= &clkops_omap2_dflt,
 	.init		= &omap2_init_clksel_parent,
@@ -1581,10 +1581,31 @@ static struct clk ssi_ssr_fck = {
 	.recalc		= &omap2_clksel_recalc,
 };
 
-static struct clk ssi_sst_fck = {
+static struct clk ssi_ssr_fck_3430es2 = {
+	.name		= "ssi_ssr_fck",
+	.ops		= &clkops_omap3430es2_ssi_wait,
+	.init		= &omap2_init_clksel_parent,
+	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1),
+	.enable_bit	= OMAP3430_EN_SSI_SHIFT,
+	.clksel_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_CLKSEL),
+	.clksel_mask	= OMAP3430_CLKSEL_SSI_MASK,
+	.clksel		= ssi_ssr_clksel,
+	.clkdm_name	= "core_l4_clkdm",
+	.recalc		= &omap2_clksel_recalc,
+};
+
+static struct clk ssi_sst_fck_3430es1 = {
 	.name		= "ssi_sst_fck",
 	.ops		= &clkops_null,
-	.parent		= &ssi_ssr_fck,
+	.parent		= &ssi_ssr_fck_3430es1,
+	.fixed_div	= 2,
+	.recalc		= &omap2_fixed_divisor_recalc,
+};
+
+static struct clk ssi_sst_fck_3430es2 = {
+	.name		= "ssi_sst_fck",
+	.ops		= &clkops_null,
+	.parent		= &ssi_ssr_fck_3430es2,
 	.fixed_div	= 2,
 	.recalc		= &omap2_fixed_divisor_recalc,
 };
@@ -1606,9 +1627,19 @@ static struct clk core_l3_ick = {
 	.recalc		= &followparent_recalc,
 };
 
-static struct clk hsotgusb_ick = {
+static struct clk hsotgusb_ick_3430es1 = {
 	.name		= "hsotgusb_ick",
-	.ops		= &clkops_omap2_dflt_wait,
+	.ops		= &clkops_omap2_dflt,
+	.parent		= &core_l3_ick,
+	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
+	.enable_bit	= OMAP3430_EN_HSOTGUSB_SHIFT,
+	.clkdm_name	= "core_l3_clkdm",
+	.recalc		= &followparent_recalc,
+};
+
+static struct clk hsotgusb_ick_3430es2 = {
+	.name		= "hsotgusb_ick",
+	.ops		= &clkops_omap3430es2_hsotgusb_wait,
 	.parent		= &core_l3_ick,
 	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
 	.enable_bit	= OMAP3430_EN_HSOTGUSB_SHIFT,
@@ -1947,7 +1978,7 @@ static struct clk ssi_l4_ick = {
 	.recalc		= &followparent_recalc,
 };
 
-static struct clk ssi_ick = {
+static struct clk ssi_ick_3430es1 = {
 	.name		= "ssi_ick",
 	.ops		= &clkops_omap2_dflt,
 	.parent		= &ssi_l4_ick,
@@ -1957,6 +1988,16 @@ static struct clk ssi_ick = {
 	.recalc		= &followparent_recalc,
 };
 
+static struct clk ssi_ick_3430es2 = {
+	.name		= "ssi_ick",
+	.ops		= &clkops_omap3430es2_ssi_wait,
+	.parent		= &ssi_l4_ick,
+	.enable_reg	= OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1),
+	.enable_bit	= OMAP3430_EN_SSI_SHIFT,
+	.clkdm_name	= "core_l4_clkdm",
+	.recalc		= &followparent_recalc,
+};
+
 /* REVISIT: Technically the TRM claims that this is CORE_CLK based,
  * but l4_ick makes more sense to me */
 
@@ -2024,7 +2065,7 @@ static struct clk des1_ick = {
 };
 
 /* DSS */
-static struct clk dss1_alwon_fck = {
+static struct clk dss1_alwon_fck_3430es1 = {
 	.name		= "dss1_alwon_fck",
 	.ops		= &clkops_omap2_dflt,
 	.parent		= &dpll4_m4x2_ck,
@@ -2034,6 +2075,16 @@ static struct clk dss1_alwon_fck = {
 	.recalc		= &followparent_recalc,
 };
 
+static struct clk dss1_alwon_fck_3430es2 = {
+	.name		= "dss1_alwon_fck",
+	.ops		= &clkops_omap3430es2_dss_usbhost_wait,
+	.parent		= &dpll4_m4x2_ck,
+	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_FCLKEN),
+	.enable_bit	= OMAP3430_EN_DSS1_SHIFT,
+	.clkdm_name	= "dss_clkdm",
+	.recalc		= &followparent_recalc,
+};
+
 static struct clk dss_tv_fck = {
 	.name		= "dss_tv_fck",
 	.ops		= &clkops_omap2_dflt,
@@ -2067,7 +2118,7 @@ static struct clk dss2_alwon_fck = {
 	.recalc		= &followparent_recalc,
 };
 
-static struct clk dss_ick = {
+static struct clk dss_ick_3430es1 = {
 	/* Handles both L3 and L4 clocks */
 	.name		= "dss_ick",
 	.ops		= &clkops_omap2_dflt,
@@ -2079,6 +2130,18 @@ static struct clk dss_ick = {
 	.recalc		= &followparent_recalc,
 };
 
+static struct clk dss_ick_3430es2 = {
+	/* Handles both L3 and L4 clocks */
+	.name		= "dss_ick",
+	.ops		= &clkops_omap3430es2_dss_usbhost_wait,
+	.parent		= &l4_ick,
+	.init		= &omap2_init_clk_clkdm,
+	.enable_reg	= OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_ICLKEN),
+	.enable_bit	= OMAP3430_CM_ICLKEN_DSS_EN_DSS_SHIFT,
+	.clkdm_name	= "dss_clkdm",
+	.recalc		= &followparent_recalc,
+};
+
 /* CAM */
 
 static struct clk cam_mclk = {
@@ -2118,7 +2181,7 @@ static struct clk csi2_96m_fck = {
 
 static struct clk usbhost_120m_fck = {
 	.name		= "usbhost_120m_fck",
-	.ops		= &clkops_omap2_dflt_wait,
+	.ops		= &clkops_omap2_dflt,
 	.parent		= &dpll5_m2_ck,
 	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN),
@@ -2129,7 +2192,7 @@ static struct clk usbhost_120m_fck = {
 
 static struct clk usbhost_48m_fck = {
 	.name		= "usbhost_48m_fck",
-	.ops		= &clkops_omap2_dflt_wait,
+	.ops		= &clkops_omap3430es2_dss_usbhost_wait,
 	.parent		= &omap_48m_fck,
 	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN),
@@ -2141,7 +2204,7 @@ static struct clk usbhost_48m_fck = {
 static struct clk usbhost_ick = {
 	/* Handles both L3 and L4 clocks */
 	.name		= "usbhost_ick",
-	.ops		= &clkops_omap2_dflt_wait,
+	.ops		= &clkops_omap3430es2_dss_usbhost_wait,
 	.parent		= &l4_ick,
 	.init		= &omap2_init_clk_clkdm,
 	.enable_reg	= OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_ICLKEN),
-- 
GitLab


From 81566a060bb8f989cc369ea28837b05bd4adcedb Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:00:15 +0530
Subject: [PATCH 0103/1153] ARM: includecheck fix: misc.c

fix the following 'make includecheck' warning:

  arch/arm/boot/compressed/misc.c: linux/compiler.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/boot/compressed/misc.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/compressed/misc.c b/arch/arm/boot/compressed/misc.c
index 9e6e512f011..17153b54613 100644
--- a/arch/arm/boot/compressed/misc.c
+++ b/arch/arm/boot/compressed/misc.c
@@ -29,7 +29,6 @@ unsigned int __machine_arch_type;
 
 static void putstr(const char *ptr);
 
-#include <linux/compiler.h>
 #include <mach/uncompress.h>
 
 #ifdef CONFIG_DEBUG_ICEDCC
-- 
GitLab


From feecaf73bb437cf72a44bd71598c6532d357f78e Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:01:39 +0530
Subject: [PATCH 0104/1153] ARM: includecheck fix: atomic.h

fix the following 'make includecheck' warning:

  arch/arm/include/asm/atomic.h: asm/system.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/include/asm/atomic.h | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/include/asm/atomic.h b/arch/arm/include/asm/atomic.h
index 9e07fe50702..9ed2377fe8e 100644
--- a/arch/arm/include/asm/atomic.h
+++ b/arch/arm/include/asm/atomic.h
@@ -159,8 +159,6 @@ static inline void atomic_clear_mask(unsigned long mask, unsigned long *addr)
 
 #else /* ARM_ARCH_6 */
 
-#include <asm/system.h>
-
 #ifdef CONFIG_SMP
 #error SMP not supported on pre-ARMv6 CPUs
 #endif
-- 
GitLab


From 44e96d452173ed22a7ba2291c7d566bf4b406f62 Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:03:08 +0530
Subject: [PATCH 0105/1153] ARM: includecheck fix: board-dm355-evm.c

fix the following 'make includecheck' warning:

  arch/arm/mach-davinci/board-dm355-evm.c: mach/common.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-davinci/board-dm355-evm.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c
index 5ac2f565d86..d6ab64ccd49 100644
--- a/arch/arm/mach-davinci/board-dm355-evm.c
+++ b/arch/arm/mach-davinci/board-dm355-evm.c
@@ -37,7 +37,6 @@
 #include <mach/serial.h>
 #include <mach/nand.h>
 #include <mach/mmc.h>
-#include <mach/common.h>
 
 #define DAVINCI_ASYNC_EMIF_CONTROL_BASE		0x01e10000
 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE	0x02000000
-- 
GitLab


From 7f25b0ac2dde2de399d6cfe42d9ec7066e665f2f Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:04:33 +0530
Subject: [PATCH 0106/1153] ARM: includecheck fix: board-dm355-leopard.c

fix the following 'make includecheck' warning:

  arch/arm/mach-davinci/board-dm355-leopard.c: mach/common.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-davinci/board-dm355-leopard.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/mach-davinci/board-dm355-leopard.c b/arch/arm/mach-davinci/board-dm355-leopard.c
index 28c9008df4f..84ad5d161a8 100644
--- a/arch/arm/mach-davinci/board-dm355-leopard.c
+++ b/arch/arm/mach-davinci/board-dm355-leopard.c
@@ -36,7 +36,6 @@
 #include <mach/serial.h>
 #include <mach/nand.h>
 #include <mach/mmc.h>
-#include <mach/common.h>
 
 #define DAVINCI_ASYNC_EMIF_CONTROL_BASE		0x01e10000
 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE	0x02000000
-- 
GitLab


From 6608168486973a33d24d27b25fc94d4743c1a1e5 Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:05:34 +0530
Subject: [PATCH 0107/1153] ARM: includecheck fix: board-dm644x-evm.c

fix the following 'make includecheck' warning:

  arch/arm/mach-davinci/board-dm644x-evm.c: mach/common.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-davinci/board-dm644x-evm.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c
index d9d40450bdc..56c8cd01de9 100644
--- a/arch/arm/mach-davinci/board-dm644x-evm.c
+++ b/arch/arm/mach-davinci/board-dm644x-evm.c
@@ -45,7 +45,6 @@
 #include <mach/nand.h>
 #include <mach/mmc.h>
 #include <mach/emac.h>
-#include <mach/common.h>
 
 #define DM644X_EVM_PHY_MASK		(0x2)
 #define DM644X_EVM_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */
-- 
GitLab


From 78eacf0b0373f524509da261b771f8baa28806b5 Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:06:42 +0530
Subject: [PATCH 0108/1153] ARM: includecheck fix: board-dm646x-evm.c

fix the following 'make includecheck' warning:

  arch/arm/mach-davinci/board-dm646x-evm.c: mach/common.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-davinci/board-dm646x-evm.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c
index e17de635262..8657e72debc 100644
--- a/arch/arm/mach-davinci/board-dm646x-evm.c
+++ b/arch/arm/mach-davinci/board-dm646x-evm.c
@@ -47,7 +47,6 @@
 #include <mach/i2c.h>
 #include <mach/mmc.h>
 #include <mach/emac.h>
-#include <mach/common.h>
 
 #define DM646X_EVM_PHY_MASK		(0x2)
 #define DM646X_EVM_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */
-- 
GitLab


From 7a33aed825c4d2bafea748384e3331661fc3a180 Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:07:26 +0530
Subject: [PATCH 0109/1153] ARM: includecheck fix: board-sffsdr.c

fix the following 'make includecheck' warning:

  arch/arm/mach-davinci/board-sffsdr.c: mach/common.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-davinci/board-sffsdr.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/mach-davinci/board-sffsdr.c b/arch/arm/mach-davinci/board-sffsdr.c
index 748a8e48541..7acdfd8ac07 100644
--- a/arch/arm/mach-davinci/board-sffsdr.c
+++ b/arch/arm/mach-davinci/board-sffsdr.c
@@ -52,7 +52,6 @@
 #include <mach/serial.h>
 #include <mach/psc.h>
 #include <mach/mux.h>
-#include <mach/common.h>
 
 #define SFFSDR_PHY_MASK		(0x2)
 #define SFFSDR_MDIO_FREQUENCY	(2200000) /* PHY bus frequency */
-- 
GitLab


From 52cbbd41f7afeceba4be2e4062138781aacd440c Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:10:02 +0530
Subject: [PATCH 0110/1153] ARM: includecheck fix: mach-omap1/mcbsp.c

fix the following 'make includecheck' warning:

  arch/arm/mach-omap1/mcbsp.c: mach/irqs.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-omap1/mcbsp.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c
index a2d7814896b..505d98cfe50 100644
--- a/arch/arm/mach-omap1/mcbsp.c
+++ b/arch/arm/mach-omap1/mcbsp.c
@@ -19,7 +19,6 @@
 
 #include <mach/irqs.h>
 #include <mach/dma.h>
-#include <mach/irqs.h>
 #include <mach/mux.h>
 #include <mach/cpu.h>
 #include <mach/mcbsp.h>
-- 
GitLab


From efda2b4c8a643290867d9f5816e36f71a5acee7d Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:11:05 +0530
Subject: [PATCH 0111/1153] ARM: includecheck fix: mach-omap2/mcbsp.c

fix the following 'make includecheck' warning:

  arch/arm/mach-omap2/mcbsp.c: mach/irqs.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-omap2/mcbsp.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/mach-omap2/mcbsp.c b/arch/arm/mach-omap2/mcbsp.c
index a5c0f0435cd..99b6e154631 100644
--- a/arch/arm/mach-omap2/mcbsp.c
+++ b/arch/arm/mach-omap2/mcbsp.c
@@ -19,7 +19,6 @@
 
 #include <mach/irqs.h>
 #include <mach/dma.h>
-#include <mach/irqs.h>
 #include <mach/mux.h>
 #include <mach/cpu.h>
 #include <mach/mcbsp.h>
-- 
GitLab


From 2e6e2c143cdefc2624722659766d1f3c098d79e1 Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:12:07 +0530
Subject: [PATCH 0112/1153] ARM: includecheck fix: plat-s3c64xx/pm.c

fix the following 'make includecheck' warning:

  arch/arm/plat-s3c64xx/pm.c: plat/regs-gpio.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/plat-s3c64xx/pm.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/plat-s3c64xx/pm.c b/arch/arm/plat-s3c64xx/pm.c
index 07a6516a4f3..47632fc7eb6 100644
--- a/arch/arm/plat-s3c64xx/pm.c
+++ b/arch/arm/plat-s3c64xx/pm.c
@@ -117,8 +117,6 @@ void s3c_pm_save_core(void)
  * this.
  */
 
-#include <plat/regs-gpio.h>
-
 static void s3c64xx_cpu_suspend(void)
 {
 	unsigned long tmp;
-- 
GitLab


From 40e03b581a8a0b638bc1e9b957ae0536a4a00ad3 Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 20:13:24 +0530
Subject: [PATCH 0113/1153] ARM: includecheck fix: plat-stmp3xxx/pinmux.c

fix the following 'make includecheck' warning:

  arch/arm/plat-stmp3xxx/pinmux.c: linux/sysdev.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/plat-stmp3xxx/pinmux.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/plat-stmp3xxx/pinmux.c b/arch/arm/plat-stmp3xxx/pinmux.c
index d4120038220..6d6b1a468ed 100644
--- a/arch/arm/plat-stmp3xxx/pinmux.c
+++ b/arch/arm/plat-stmp3xxx/pinmux.c
@@ -22,7 +22,6 @@
 #include <linux/sysdev.h>
 #include <linux/string.h>
 #include <linux/bitops.h>
-#include <linux/sysdev.h>
 #include <linux/irq.h>
 
 #include <mach/hardware.h>
-- 
GitLab


From 505d62d073b528859b43bfb463a6ceaf3581469e Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior <bigeasy@breakpoint.cc>
Date: Sun, 26 Jul 2009 14:57:54 +0200
Subject: [PATCH 0114/1153] avr32/lib: fix unaligned memcpy()

memcpy(p, unaligned, 4..) returns (p + num_of_unaligned_by_copied)
instead of p because p is not preserved in the unaligned case.

Noticed by Herbert Xu's superior parameter recycling coding technique
which let the md4 self-test fail on avr32.

Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
---
 arch/avr32/lib/memcpy.S | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/arch/avr32/lib/memcpy.S b/arch/avr32/lib/memcpy.S
index 0abb26142b6..93e74b6fcdb 100644
--- a/arch/avr32/lib/memcpy.S
+++ b/arch/avr32/lib/memcpy.S
@@ -24,8 +24,8 @@ memcpy:
 	brne	1f
 
 	/* At this point, "from" is word-aligned */
-2:	sub	r10, 4
-	mov	r9, r12
+2:	mov	r9, r12
+5:	sub	r10, 4
 	brlt	4f
 
 3:	ld.w	r8, r11++
@@ -59,4 +59,13 @@ memcpy:
 	st.b	r12++, r8
 	ld.ub	r8, r11++
 	st.b	r12++, r8
-	rjmp	2b
+	mov	r8, r12
+	add	pc, pc, r9
+	sub	r8, 1
+	nop
+	sub	r8, 1
+	nop
+	sub	r8, 1
+	nop
+	mov	r9, r8
+	rjmp	5b
-- 
GitLab


From 251ab1a37d9ba810593d5fbf2482bc4ba773fab2 Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior <bigeasy@breakpoint.cc>
Date: Sun, 26 Jul 2009 14:58:34 +0200
Subject: [PATCH 0115/1153] avr32/lib: fix unaligned memcpy where len < 4

in case of memcpy(p, unaligned, 1..3) we get 1..3 as the
return value instead of p

Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
---
 arch/avr32/lib/memcpy.S | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/avr32/lib/memcpy.S b/arch/avr32/lib/memcpy.S
index 93e74b6fcdb..c2ca49d705a 100644
--- a/arch/avr32/lib/memcpy.S
+++ b/arch/avr32/lib/memcpy.S
@@ -49,6 +49,7 @@ memcpy:
 
 	/* Handle unaligned "from" pointer */
 1:	sub	r10, 4
+	movlt	r9, r12
 	brlt	4b
 	add	r10, r9
 	lsl	r9, 2
-- 
GitLab


From 92c548cd35d50df398f442b07021150094578460 Mon Sep 17 00:00:00 2001
From: Ben Nizette <ben@niasdigital.com>
Date: Mon, 20 Apr 2009 12:36:53 +1000
Subject: [PATCH 0116/1153] favr32: improve touchscreen response

The ezLCD+101 board (to which an favr-32 is fitted) has a long,
unshielded, nasty lead between the touch panel and the ads7843 touch
controller.  In order to get satisfactory response then, we need to
employ every noise-reduction trick in the driver's arsenal.  After
extensive fiddling I've found some good settings:

1) We keep vref on all the time to dramatically reduce settling times
(at the cost of a tiny increase in power consumption).

2) Despite 1 the settling time is still non-zero.  500uS is plenty of
time for the signals to settle

3) Despite 1 and 2 there's still a little bit of noise around.  By
setting a pen recheck delay we make the panel feel less touchy and
twitchy.

Someone with more time and patience myself might be able to tune this
numbers further but these settings are now perfectly acceptable for
normal use.

Tested on ezLCD+101 though should only improve response on other ezLCD+/
favr-32 boards too.

Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
---
 arch/avr32/boards/favr-32/setup.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/avr32/boards/favr-32/setup.c b/arch/avr32/boards/favr-32/setup.c
index 46c9b0a224c..75f19f47fb2 100644
--- a/arch/avr32/boards/favr-32/setup.c
+++ b/arch/avr32/boards/favr-32/setup.c
@@ -72,6 +72,10 @@ static struct ads7846_platform_data ads7843_data = {
 	.debounce_max		= 20,
 	.debounce_rep		= 4,
 	.debounce_tol		= 5,
+
+	.keep_vref_on		= true,
+	.settle_delay_usecs	= 500,
+	.penirq_recheck_delay_usecs = 100,
 };
 
 static struct spi_board_info __initdata spi1_board_info[] = {
-- 
GitLab


From c640e1cb45cb9ff6b02f5f130a4f2a58ab9ebe55 Mon Sep 17 00:00:00 2001
From: Tomas Cech <sleep_walker@suse.cz>
Date: Mon, 27 Jul 2009 14:16:31 +0100
Subject: [PATCH 0117/1153] ARM: 5623/1: Treo680: ir shutdown typo fix
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

correct GPIO freed in treo680_irda_shutdown()

Signed-off-by: Tomáš ?ech <sleep_walker@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-pxa/treo680.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-pxa/treo680.c b/arch/arm/mach-pxa/treo680.c
index a06f19edebb..753ec4df17b 100644
--- a/arch/arm/mach-pxa/treo680.c
+++ b/arch/arm/mach-pxa/treo680.c
@@ -409,7 +409,7 @@ err1:
 
 static void treo680_irda_shutdown(struct device *dev)
 {
-	gpio_free(GPIO_NR_TREO680_AMP_EN);
+	gpio_free(GPIO_NR_TREO680_IR_EN);
 }
 
 static struct pxaficp_platform_data treo680_ficp_info = {
-- 
GitLab


From 631c07c8d12bcc6ce4a0fbfbd64ea843d78e2b10 Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Mon, 27 Jul 2009 13:57:00 -0400
Subject: [PATCH 0118/1153] Btrfs: Correct redundant test in add_inode_ref

dir has already been tested.  It seems that this test should be on the
recently returned value inode.

A simplified version of the semantic match that finds this problem is as
follows: (http://www.emn.fr/x-info/coccinelle/)

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/tree-log.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/btrfs/tree-log.c b/fs/btrfs/tree-log.c
index 19560686261..11d0787c618 100644
--- a/fs/btrfs/tree-log.c
+++ b/fs/btrfs/tree-log.c
@@ -797,7 +797,7 @@ static noinline int add_inode_ref(struct btrfs_trans_handle *trans,
 		return -ENOENT;
 
 	inode = read_one_inode(root, key->objectid);
-	BUG_ON(!dir);
+	BUG_ON(!inode);
 
 	ref_ptr = btrfs_item_ptr_offset(eb, slot);
 	ref_end = ref_ptr + btrfs_item_size_nr(eb, slot);
-- 
GitLab


From 68b38550ddbea13d296184bf69edff387618b1d3 Mon Sep 17 00:00:00 2001
From: Josef Bacik <josef@redhat.com>
Date: Mon, 27 Jul 2009 13:57:01 -0400
Subject: [PATCH 0119/1153] Btrfs: change how we unpin extents

We are racy with async block caching and unpinning extents.  This patch makes
things much less complicated by only unpinning the extent if the block group is
cached.  We check the block_group->cached var under the block_group->lock spin
lock.  If it is set to BTRFS_CACHE_FINISHED then we update the pinned counters,
and unpin the extent and add the free space back.  If it is not set to this, we
start the caching of the block group so the next time we unpin extents we can
unpin the extent.  This keeps us from racing with the async caching threads,
lets us kill the fs wide async thread counter, and keeps us from having to set
DELALLOC bits for every extent we hit if there are caching kthreads going.

One thing that needed to be changed was btrfs_free_super_mirror_extents.  Now
instead of just looking for LOCKED extents, we also look for DIRTY extents,
since we could have left some extents pinned in the previous transaction that
will never get freed now that we are unmounting, which would cause us to leak
memory.  So btrfs_free_super_mirror_extents has been changed to
btrfs_free_pinned_extents, and it will clear the extents locked for the super
mirror, and any remaining pinned extents that may be present.  Thank you,

Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/ctree.h       |   5 +-
 fs/btrfs/disk-io.c     |   3 +-
 fs/btrfs/extent-tree.c | 149 ++++++++++++-----------------------------
 fs/btrfs/tree-log.c    |   2 +-
 4 files changed, 46 insertions(+), 113 deletions(-)

diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h
index 42b03c4ee49..17ad92c29cf 100644
--- a/fs/btrfs/ctree.h
+++ b/fs/btrfs/ctree.h
@@ -845,7 +845,6 @@ struct btrfs_fs_info {
 	atomic_t async_submit_draining;
 	atomic_t nr_async_bios;
 	atomic_t async_delalloc_pages;
-	atomic_t async_caching_threads;
 
 	/*
 	 * this is used by the balancing code to wait for all the pending
@@ -1926,7 +1925,7 @@ int btrfs_run_delayed_refs(struct btrfs_trans_handle *trans,
 			   struct btrfs_root *root, unsigned long count);
 int btrfs_lookup_extent(struct btrfs_root *root, u64 start, u64 len);
 int btrfs_update_pinned_extents(struct btrfs_root *root,
-				u64 bytenr, u64 num, int pin, int mark_free);
+				u64 bytenr, u64 num, int pin);
 int btrfs_drop_leaf_ref(struct btrfs_trans_handle *trans,
 			struct btrfs_root *root, struct extent_buffer *leaf);
 int btrfs_cross_ref_exist(struct btrfs_trans_handle *trans,
@@ -2011,7 +2010,7 @@ void btrfs_delalloc_reserve_space(struct btrfs_root *root, struct inode *inode,
 				 u64 bytes);
 void btrfs_delalloc_free_space(struct btrfs_root *root, struct inode *inode,
 			      u64 bytes);
-void btrfs_free_super_mirror_extents(struct btrfs_fs_info *info);
+void btrfs_free_pinned_extents(struct btrfs_fs_info *info);
 /* ctree.c */
 int btrfs_bin_search(struct extent_buffer *eb, struct btrfs_key *key,
 		     int level, int *slot);
diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c
index ec2c915f7f4..c658397c747 100644
--- a/fs/btrfs/disk-io.c
+++ b/fs/btrfs/disk-io.c
@@ -1567,7 +1567,6 @@ struct btrfs_root *open_ctree(struct super_block *sb,
 	atomic_set(&fs_info->async_delalloc_pages, 0);
 	atomic_set(&fs_info->async_submit_draining, 0);
 	atomic_set(&fs_info->nr_async_bios, 0);
-	atomic_set(&fs_info->async_caching_threads, 0);
 	fs_info->sb = sb;
 	fs_info->max_extent = (u64)-1;
 	fs_info->max_inline = 8192 * 1024;
@@ -2339,7 +2338,7 @@ int close_ctree(struct btrfs_root *root)
 	free_extent_buffer(root->fs_info->csum_root->commit_root);
 
 	btrfs_free_block_groups(root->fs_info);
-	btrfs_free_super_mirror_extents(root->fs_info);
+	btrfs_free_pinned_extents(root->fs_info);
 
 	del_fs_roots(fs_info);
 
diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index 508df5f7d2e..08188f1615d 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -153,18 +153,26 @@ block_group_cache_tree_search(struct btrfs_fs_info *info, u64 bytenr,
 	return ret;
 }
 
-void btrfs_free_super_mirror_extents(struct btrfs_fs_info *info)
+/*
+ * We always set EXTENT_LOCKED for the super mirror extents so we don't
+ * overwrite them, so those bits need to be unset.  Also, if we are unmounting
+ * with pinned extents still sitting there because we had a block group caching,
+ * we need to clear those now, since we are done.
+ */
+void btrfs_free_pinned_extents(struct btrfs_fs_info *info)
 {
 	u64 start, end, last = 0;
 	int ret;
 
 	while (1) {
 		ret = find_first_extent_bit(&info->pinned_extents, last,
-					    &start, &end, EXTENT_LOCKED);
+					    &start, &end,
+					    EXTENT_LOCKED|EXTENT_DIRTY);
 		if (ret)
 			break;
 
-		unlock_extent(&info->pinned_extents, start, end, GFP_NOFS);
+		clear_extent_bits(&info->pinned_extents, start, end,
+				  EXTENT_LOCKED|EXTENT_DIRTY, GFP_NOFS);
 		last = end+1;
 	}
 }
@@ -209,8 +217,7 @@ static u64 add_new_free_space(struct btrfs_block_group_cache *block_group,
 	while (start < end) {
 		ret = find_first_extent_bit(&info->pinned_extents, start,
 					    &extent_start, &extent_end,
-					    EXTENT_DIRTY|EXTENT_LOCKED|
-					    EXTENT_DELALLOC);
+					    EXTENT_DIRTY|EXTENT_LOCKED);
 		if (ret)
 			break;
 
@@ -238,67 +245,6 @@ static u64 add_new_free_space(struct btrfs_block_group_cache *block_group,
 	return total_added;
 }
 
-DEFINE_MUTEX(discard_mutex);
-
-/*
- * if async kthreads are running when we cross transactions, we mark any pinned
- * extents with EXTENT_DELALLOC and then let the caching kthreads clean up those
- * extents when they are done.  Also we run this from btrfs_finish_extent_commit
- * in case there were some pinned extents that were missed because we had
- * already cached that block group.
- */
-static void btrfs_discard_pinned_extents(struct btrfs_fs_info *fs_info,
-					 struct btrfs_block_group_cache *cache)
-{
-	u64 start, end, last;
-	int ret;
-
-	if (!cache)
-		last = 0;
-	else
-		last = cache->key.objectid;
-
-	mutex_lock(&discard_mutex);
-	while (1) {
-		ret = find_first_extent_bit(&fs_info->pinned_extents, last,
-					    &start, &end, EXTENT_DELALLOC);
-		if (ret)
-			break;
-
-		if (cache && start >= cache->key.objectid + cache->key.offset)
-			break;
-
-
-		if (!cache) {
-			cache = btrfs_lookup_block_group(fs_info, start);
-			BUG_ON(!cache);
-
-			start = max(start, cache->key.objectid);
-			end = min(end, cache->key.objectid + cache->key.offset - 1);
-
-			if (block_group_cache_done(cache))
-				btrfs_add_free_space(cache, start,
-						     end - start + 1);
-			cache = NULL;
-		} else {
-			start = max(start, cache->key.objectid);
-			end = min(end, cache->key.objectid + cache->key.offset - 1);
-			btrfs_add_free_space(cache, start, end - start + 1);
-		}
-
-		clear_extent_bits(&fs_info->pinned_extents, start, end,
-				  EXTENT_DELALLOC, GFP_NOFS);
-		last = end + 1;
-
-		if (need_resched()) {
-			mutex_unlock(&discard_mutex);
-			cond_resched();
-			mutex_lock(&discard_mutex);
-		}
-	}
-	mutex_unlock(&discard_mutex);
-}
-
 static int caching_kthread(void *data)
 {
 	struct btrfs_block_group_cache *block_group = data;
@@ -317,7 +263,6 @@ static int caching_kthread(void *data)
 	if (!path)
 		return -ENOMEM;
 
-	atomic_inc(&fs_info->async_caching_threads);
 	atomic_inc(&block_group->space_info->caching_threads);
 	last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET);
 again:
@@ -399,13 +344,9 @@ next:
 err:
 	btrfs_free_path(path);
 	up_read(&fs_info->extent_root->commit_root_sem);
-	atomic_dec(&fs_info->async_caching_threads);
 	atomic_dec(&block_group->space_info->caching_threads);
 	wake_up(&block_group->caching_q);
 
-	if (!ret)
-		btrfs_discard_pinned_extents(fs_info, block_group);
-
 	return 0;
 }
 
@@ -1867,7 +1808,7 @@ static int run_one_delayed_ref(struct btrfs_trans_handle *trans,
 				BUG_ON(ret);
 			}
 			btrfs_update_pinned_extents(root, node->bytenr,
-						    node->num_bytes, 1, 0);
+						    node->num_bytes, 1);
 			update_reserved_extents(root, node->bytenr,
 						node->num_bytes, 0);
 		}
@@ -3100,19 +3041,15 @@ static u64 first_logical_byte(struct btrfs_root *root, u64 search_start)
 }
 
 int btrfs_update_pinned_extents(struct btrfs_root *root,
-				u64 bytenr, u64 num, int pin, int mark_free)
+				u64 bytenr, u64 num, int pin)
 {
 	u64 len;
 	struct btrfs_block_group_cache *cache;
 	struct btrfs_fs_info *fs_info = root->fs_info;
 
-	if (pin) {
+	if (pin)
 		set_extent_dirty(&fs_info->pinned_extents,
 				bytenr, bytenr + num - 1, GFP_NOFS);
-	} else {
-		clear_extent_dirty(&fs_info->pinned_extents,
-				bytenr, bytenr + num - 1, GFP_NOFS);
-	}
 
 	while (num > 0) {
 		cache = btrfs_lookup_block_group(fs_info, bytenr);
@@ -3128,14 +3065,34 @@ int btrfs_update_pinned_extents(struct btrfs_root *root,
 			spin_unlock(&cache->space_info->lock);
 			fs_info->total_pinned += len;
 		} else {
+			int unpin = 0;
+
+			/*
+			 * in order to not race with the block group caching, we
+			 * only want to unpin the extent if we are cached.  If
+			 * we aren't cached, we want to start async caching this
+			 * block group so we can free the extent the next time
+			 * around.
+			 */
 			spin_lock(&cache->space_info->lock);
 			spin_lock(&cache->lock);
-			cache->pinned -= len;
-			cache->space_info->bytes_pinned -= len;
+			unpin = (cache->cached == BTRFS_CACHE_FINISHED);
+			if (likely(unpin)) {
+				cache->pinned -= len;
+				cache->space_info->bytes_pinned -= len;
+				fs_info->total_pinned -= len;
+			}
 			spin_unlock(&cache->lock);
 			spin_unlock(&cache->space_info->lock);
-			fs_info->total_pinned -= len;
-			if (block_group_cache_done(cache) && mark_free)
+
+			if (likely(unpin))
+				clear_extent_dirty(&fs_info->pinned_extents,
+						   bytenr, bytenr + len -1,
+						   GFP_NOFS);
+			else
+				cache_block_group(cache);
+
+			if (unpin)
 				btrfs_add_free_space(cache, bytenr, len);
 		}
 		btrfs_put_block_group(cache);
@@ -3181,27 +3138,15 @@ int btrfs_copy_pinned(struct btrfs_root *root, struct extent_io_tree *copy)
 	u64 last = 0;
 	u64 start;
 	u64 end;
-	bool caching_kthreads = false;
 	struct extent_io_tree *pinned_extents = &root->fs_info->pinned_extents;
 	int ret;
 
-	if (atomic_read(&root->fs_info->async_caching_threads))
-		caching_kthreads = true;
-
 	while (1) {
 		ret = find_first_extent_bit(pinned_extents, last,
 					    &start, &end, EXTENT_DIRTY);
 		if (ret)
 			break;
 
-		/*
-		 * we need to make sure that the pinned extents don't go away
-		 * while we are caching block groups
-		 */
-		if (unlikely(caching_kthreads))
-			set_extent_delalloc(pinned_extents, start, end,
-					    GFP_NOFS);
-
 		set_extent_dirty(copy, start, end, GFP_NOFS);
 		last = end + 1;
 	}
@@ -3215,12 +3160,6 @@ int btrfs_finish_extent_commit(struct btrfs_trans_handle *trans,
 	u64 start;
 	u64 end;
 	int ret;
-	int mark_free = 1;
-
-	ret = find_first_extent_bit(&root->fs_info->pinned_extents, 0,
-				    &start, &end, EXTENT_DELALLOC);
-	if (!ret)
-		mark_free = 0;
 
 	while (1) {
 		ret = find_first_extent_bit(unpin, 0, &start, &end,
@@ -3231,16 +3170,12 @@ int btrfs_finish_extent_commit(struct btrfs_trans_handle *trans,
 		ret = btrfs_discard_extent(root, start, end + 1 - start);
 
 		/* unlocks the pinned mutex */
-		btrfs_update_pinned_extents(root, start, end + 1 - start, 0,
-					    mark_free);
+		btrfs_update_pinned_extents(root, start, end + 1 - start, 0);
 		clear_extent_dirty(unpin, start, end, GFP_NOFS);
 
 		cond_resched();
 	}
 
-	if (unlikely(!mark_free))
-		btrfs_discard_pinned_extents(root->fs_info, NULL);
-
 	return ret;
 }
 
@@ -3281,7 +3216,7 @@ static int pin_down_bytes(struct btrfs_trans_handle *trans,
 pinit:
 	btrfs_set_path_blocking(path);
 	/* unlocks the pinned mutex */
-	btrfs_update_pinned_extents(root, bytenr, num_bytes, 1, 0);
+	btrfs_update_pinned_extents(root, bytenr, num_bytes, 1);
 
 	BUG_ON(err < 0);
 	return 0;
@@ -3592,7 +3527,7 @@ int btrfs_free_extent(struct btrfs_trans_handle *trans,
 	if (root_objectid == BTRFS_TREE_LOG_OBJECTID) {
 		WARN_ON(owner >= BTRFS_FIRST_FREE_OBJECTID);
 		/* unlocks the pinned mutex */
-		btrfs_update_pinned_extents(root, bytenr, num_bytes, 1, 0);
+		btrfs_update_pinned_extents(root, bytenr, num_bytes, 1);
 		update_reserved_extents(root, bytenr, num_bytes, 0);
 		ret = 0;
 	} else if (owner < BTRFS_FIRST_FREE_OBJECTID) {
diff --git a/fs/btrfs/tree-log.c b/fs/btrfs/tree-log.c
index 11d0787c618..d91b0de7c50 100644
--- a/fs/btrfs/tree-log.c
+++ b/fs/btrfs/tree-log.c
@@ -264,7 +264,7 @@ static int process_one_buffer(struct btrfs_root *log,
 {
 	if (wc->pin)
 		btrfs_update_pinned_extents(log->fs_info->extent_root,
-					    eb->start, eb->len, 1, 0);
+					    eb->start, eb->len, 1);
 
 	if (btrfs_buffer_uptodate(eb, gen)) {
 		if (wc->write)
-- 
GitLab


From 3995bd9332a51b626237d6671cfeb7235e6c1305 Mon Sep 17 00:00:00 2001
From: Johannes Berg <johannes@sipsolutions.net>
Date: Fri, 24 Jul 2009 11:13:14 -0700
Subject: [PATCH 0120/1153] iwlwifi: fix TX queue race

I had a problem on 4965 hardware (well, probably other hardware too,
but others don't survive my stress testing right now, unfortunately)
where the driver was sending invalid commands to the device, but no
such thing could be seen from the driver's point of view. I could
reproduce this fairly easily by sending multiple TCP streams with
iperf on different TIDs, though sometimes a single iperf stream was
sufficient. It even happened with a single core, but I have forced
preemption turned on.

The culprit was a queue overrun, where we advanced the queue's write
pointer over the read pointer. After careful analysis I've come to
the conclusion that the cause is a race condition between iwlwifi
and mac80211.

mac80211, of course, checks whether the queue is stopped, before
transmitting a frame. This effectively looks like this:

        lock(queues)
        if (stopped(queue)) {
                unlock(queues)
                return busy;
	}
        unlock(queues)
        ...             <-- this place will be important
			    there is some more code here
        drv_tx(frame)

The driver, on the other hand, can stop and start queues, which does

        lock(queues)
        mark_running/stopped(queue)
        unlock(queues)

	[if marked running: wake up tasklet to send pending frames]

Now, however, once the driver starts the queue, mac80211 can see that
and end up at the marked place above, at which point for some reason the
driver seems to stop the queue again (I don't understand that) and then
we end up transmitting while the queue is actually full.

Now, this shouldn't actually matter much, but for some reason I've seen
it happen multiple times in a row and the queue actually overflows, at
which point the queue bites itself in the tail and things go completely
wrong.

This patch fixes this by just dropping the packet should this have
happened, and making the lock in iwlwifi cover everything so iwlwifi
can't race against itself (dropping the lock there might make it more
likely, but it did seem to happen without that too).

Since we can't hold the lock across drv_tx() above, I see no way to fix
this in mac80211, but I also don't understand why I haven't seen this
before -- maybe I just never stress tested it this badly.

With this patch, the device has survived many minutes of simultanously
sending two iperf streams on different TIDs with combined throughput
of about 60 Mbps.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/iwlwifi/iwl-tx.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c
index 9bbeec9427f..5febb318636 100644
--- a/drivers/net/wireless/iwlwifi/iwl-tx.c
+++ b/drivers/net/wireless/iwlwifi/iwl-tx.c
@@ -720,8 +720,6 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb)
 		goto drop_unlock;
 	}
 
-	spin_unlock_irqrestore(&priv->lock, flags);
-
 	hdr_len = ieee80211_hdrlen(fc);
 
 	/* Find (or create) index into station table for destination station */
@@ -729,7 +727,7 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb)
 	if (sta_id == IWL_INVALID_STATION) {
 		IWL_DEBUG_DROP(priv, "Dropping - INVALID STATION: %pM\n",
 			       hdr->addr1);
-		goto drop;
+		goto drop_unlock;
 	}
 
 	IWL_DEBUG_TX(priv, "station Id %d\n", sta_id);
@@ -750,14 +748,17 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb)
 			txq_id = priv->stations[sta_id].tid[tid].agg.txq_id;
 			swq_id = iwl_virtual_agg_queue_num(swq_id, txq_id);
 		}
-		priv->stations[sta_id].tid[tid].tfds_in_queue++;
 	}
 
 	txq = &priv->txq[txq_id];
 	q = &txq->q;
 	txq->swq_id = swq_id;
 
-	spin_lock_irqsave(&priv->lock, flags);
+	if (unlikely(iwl_queue_space(q) < q->high_mark))
+		goto drop_unlock;
+
+	if (ieee80211_is_data_qos(fc))
+		priv->stations[sta_id].tid[tid].tfds_in_queue++;
 
 	/* Set up driver data for this TFD */
 	memset(&(txq->txb[q->write_ptr]), 0, sizeof(struct iwl_tx_info));
@@ -902,7 +903,6 @@ int iwl_tx_skb(struct iwl_priv *priv, struct sk_buff *skb)
 
 drop_unlock:
 	spin_unlock_irqrestore(&priv->lock, flags);
-drop:
 	return -1;
 }
 EXPORT_SYMBOL(iwl_tx_skb);
-- 
GitLab


From 45f5fa32b130b2a59f9b726be45ce7fa73fb834c Mon Sep 17 00:00:00 2001
From: reinette chatre <reinette.chatre@intel.com>
Date: Tue, 21 Jul 2009 09:29:07 -0700
Subject: [PATCH 0121/1153] iwlagn: fix minimum number of queues setting

We need to provide a reasonable minimum that will result in a
working setup if used. Set minimum to be 10 to provide for
4 standard TX queues + 1 command queue + 2 (unused) HCCA queues +
4 HT queues (one per AC).

We allow the user to change the number of queues used via a module
parameter and use this minimum value to check if it is valid. Without
this patch a user can select a value for the number of queues that
will result in a failing setup.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/iwlwifi/iwl-3945.h     | 2 +-
 drivers/net/wireless/iwlwifi/iwl-dev.h      | 6 ++++--
 drivers/net/wireless/iwlwifi/iwl3945-base.c | 4 ++--
 3 files changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.h b/drivers/net/wireless/iwlwifi/iwl-3945.h
index fbb3a573463..2de6471d4be 100644
--- a/drivers/net/wireless/iwlwifi/iwl-3945.h
+++ b/drivers/net/wireless/iwlwifi/iwl-3945.h
@@ -112,7 +112,7 @@ enum iwl3945_antenna {
 #define IWL_TX_FIFO_NONE	7
 
 /* Minimum number of queues. MAX_NUM is defined in hw specific files */
-#define IWL_MIN_NUM_QUEUES	4
+#define IWL39_MIN_NUM_QUEUES	4
 
 #define IEEE80211_DATA_LEN              2304
 #define IEEE80211_4ADDR_LEN             30
diff --git a/drivers/net/wireless/iwlwifi/iwl-dev.h b/drivers/net/wireless/iwlwifi/iwl-dev.h
index e2d620f0b6e..650e20af20f 100644
--- a/drivers/net/wireless/iwlwifi/iwl-dev.h
+++ b/drivers/net/wireless/iwlwifi/iwl-dev.h
@@ -258,8 +258,10 @@ struct iwl_channel_info {
 #define IWL_TX_FIFO_HCCA_2	6
 #define IWL_TX_FIFO_NONE	7
 
-/* Minimum number of queues. MAX_NUM is defined in hw specific files */
-#define IWL_MIN_NUM_QUEUES	4
+/* Minimum number of queues. MAX_NUM is defined in hw specific files.
+ * Set the minimum to accommodate the 4 standard TX queues, 1 command
+ * queue, 2 (unused) HCCA queues, and 4 HT queues (one for each AC) */
+#define IWL_MIN_NUM_QUEUES	10
 
 /* Power management (not Tx power) structures */
 
diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c
index 956798f2c80..2f50ab60bfd 100644
--- a/drivers/net/wireless/iwlwifi/iwl3945-base.c
+++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c
@@ -4018,10 +4018,10 @@ static int iwl3945_pci_probe(struct pci_dev *pdev, const struct pci_device_id *e
 	SET_IEEE80211_DEV(hw, &pdev->dev);
 
 	if ((iwl3945_mod_params.num_of_queues > IWL39_MAX_NUM_QUEUES) ||
-	     (iwl3945_mod_params.num_of_queues < IWL_MIN_NUM_QUEUES)) {
+	     (iwl3945_mod_params.num_of_queues < IWL39_MIN_NUM_QUEUES)) {
 		IWL_ERR(priv,
 			"invalid queues_num, should be between %d and %d\n",
-			IWL_MIN_NUM_QUEUES, IWL39_MAX_NUM_QUEUES);
+			IWL39_MIN_NUM_QUEUES, IWL39_MAX_NUM_QUEUES);
 		err = -EINVAL;
 		goto out_ieee80211_free_hw;
 	}
-- 
GitLab


From 2a21f86917f7a9fe13b180e895a816871a234dee Mon Sep 17 00:00:00 2001
From: Dan Carpenter <error27@gmail.com>
Date: Sat, 25 Jul 2009 15:22:59 +0300
Subject: [PATCH 0122/1153] wireless: ERR_PTR vs null

iwm_wdev_alloc() returns an ERR_PTR on failure and not null.  It also
prints its own dev_err() message so I removed that as well.

Compile tested only.  Sorry.
Found by smatch (http://repo.or.cz/w/smatch.git).

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/iwmc3200wifi/netdev.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/iwmc3200wifi/netdev.c b/drivers/net/wireless/iwmc3200wifi/netdev.c
index aea5ccf24cc..bf294e41753 100644
--- a/drivers/net/wireless/iwmc3200wifi/netdev.c
+++ b/drivers/net/wireless/iwmc3200wifi/netdev.c
@@ -106,10 +106,8 @@ void *iwm_if_alloc(int sizeof_bus, struct device *dev,
 	int ret = 0;
 
 	wdev = iwm_wdev_alloc(sizeof_bus, dev);
-	if (!wdev) {
-		dev_err(dev, "no memory for wireless device instance\n");
-		return ERR_PTR(-ENOMEM);
-	}
+	if (IS_ERR(wdev))
+		return wdev;
 
 	iwm = wdev_to_iwm(wdev);
 	iwm->bus_ops = if_ops;
-- 
GitLab


From 3d0ccd021b23c18ea2d399fe4a43c955485c765c Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Sat, 25 Jul 2009 23:02:32 +0200
Subject: [PATCH 0123/1153] airo: Buffer overflow

SSID_rid has space for only 3 ssids.
txPowerLevels[i] is read before the bounds check for i

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/airo.c | 13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)

diff --git a/drivers/net/wireless/airo.c b/drivers/net/wireless/airo.c
index c70604f0329..8ce5e4cee16 100644
--- a/drivers/net/wireless/airo.c
+++ b/drivers/net/wireless/airo.c
@@ -5918,20 +5918,19 @@ static int airo_set_essid(struct net_device *dev,
 	readSsidRid(local, &SSID_rid);
 
 	/* Check if we asked for `any' */
-	if(dwrq->flags == 0) {
+	if (dwrq->flags == 0) {
 		/* Just send an empty SSID list */
 		memset(&SSID_rid, 0, sizeof(SSID_rid));
 	} else {
-		int	index = (dwrq->flags & IW_ENCODE_INDEX) - 1;
+		unsigned index = (dwrq->flags & IW_ENCODE_INDEX) - 1;
 
 		/* Check the size of the string */
-		if(dwrq->length > IW_ESSID_MAX_SIZE) {
+		if (dwrq->length > IW_ESSID_MAX_SIZE)
 			return -E2BIG ;
-		}
+
 		/* Check if index is valid */
-		if((index < 0) || (index >= 4)) {
+		if (index >= ARRAY_SIZE(SSID_rid.ssids))
 			return -EINVAL;
-		}
 
 		/* Set the SSID */
 		memset(SSID_rid.ssids[index].ssid, 0,
@@ -6819,7 +6818,7 @@ static int airo_set_txpow(struct net_device *dev,
 		return -EINVAL;
 	}
 	clear_bit (FLAG_RADIO_OFF, &local->flags);
-	for (i = 0; cap_rid.txPowerLevels[i] && (i < 8); i++)
+	for (i = 0; i < 8 && cap_rid.txPowerLevels[i]; i++)
 		if (v == cap_rid.txPowerLevels[i]) {
 			readConfigRid(local, 1);
 			local->config.txPower = v;
-- 
GitLab


From 008749fc9917b799c469478141ddd1a4c81d06ca Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Sat, 25 Jul 2009 23:21:22 +0200
Subject: [PATCH 0124/1153] ath9k: Read outside array bounds

Incorrect limits leads to reads outside array bounds.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/ath/ath9k/eeprom.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/eeprom.c b/drivers/net/wireless/ath/ath9k/eeprom.c
index a2fda702b62..ce0e86c36a8 100644
--- a/drivers/net/wireless/ath/ath9k/eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/eeprom.c
@@ -460,7 +460,7 @@ static int ath9k_hw_4k_check_eeprom(struct ath_hw *ah)
 		integer = swab32(eep->modalHeader.antCtrlCommon);
 		eep->modalHeader.antCtrlCommon = integer;
 
-		for (i = 0; i < AR5416_MAX_CHAINS; i++) {
+		for (i = 0; i < AR5416_EEP4K_MAX_CHAINS; i++) {
 			integer = swab32(eep->modalHeader.antCtrlChain[i]);
 			eep->modalHeader.antCtrlChain[i] = integer;
 		}
@@ -914,7 +914,7 @@ static void ath9k_hw_set_4k_power_per_rate_table(struct ath_hw *ah,
 			ctlMode, numCtlModes, isHt40CtlMode,
 			(pCtlMode[ctlMode] & EXT_ADDITIVE));
 
-		for (i = 0; (i < AR5416_NUM_CTLS) &&
+		for (i = 0; (i < AR5416_EEP4K_NUM_CTLS) &&
 				pEepData->ctlIndex[i]; i++) {
 			DPRINTF(ah->ah_sc, ATH_DBG_EEPROM,
 				"  LOOP-Ctlidx %d: cfgCtl 0x%2.2x "
-- 
GitLab


From 082e708acc50a5b625b9bde0bb1af90dfdbd1942 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Sat, 25 Jul 2009 23:34:31 +0200
Subject: [PATCH 0125/1153] iwlwifi: Read outside array bounds

tid is bounded (above) by the size of default_tid_to_tx_fifo (17 elements), but
the size of priv->stations[].tid[] is MAX_TID_COUNT (9) elements.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/iwlwifi/iwl-tx.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c
index 5febb318636..2e89040e63b 100644
--- a/drivers/net/wireless/iwlwifi/iwl-tx.c
+++ b/drivers/net/wireless/iwlwifi/iwl-tx.c
@@ -1171,6 +1171,8 @@ int iwl_tx_agg_start(struct iwl_priv *priv, const u8 *ra, u16 tid, u16 *ssn)
 		IWL_ERR(priv, "Start AGG on invalid station\n");
 		return -ENXIO;
 	}
+	if (unlikely(tid >= MAX_TID_COUNT))
+		return -EINVAL;
 
 	if (priv->stations[sta_id].tid[tid].agg.state != IWL_AGG_OFF) {
 		IWL_ERR(priv, "Start AGG when state is not IWL_AGG_OFF !\n");
-- 
GitLab


From 78f1a8b758d57c2d2c9f3db7199cd30803854c82 Mon Sep 17 00:00:00 2001
From: "Luis R. Rodriguez" <lrodriguez@atheros.com>
Date: Mon, 27 Jul 2009 08:38:25 -0700
Subject: [PATCH 0126/1153] mac80211: do not queue work after suspend in the
 dynamic ps timer

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 net/mac80211/mlme.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c
index aca22b00b6a..07e7e41816b 100644
--- a/net/mac80211/mlme.c
+++ b/net/mac80211/mlme.c
@@ -721,7 +721,7 @@ void ieee80211_dynamic_ps_timer(unsigned long data)
 {
 	struct ieee80211_local *local = (void *) data;
 
-	if (local->quiescing)
+	if (local->quiescing || local->suspended)
 		return;
 
 	queue_work(local->hw.workqueue, &local->dynamic_ps_enable_work);
-- 
GitLab


From 0e83815be719d3391bf5ea24b7fe696c07dbd417 Mon Sep 17 00:00:00 2001
From: Robert Richter <robert.richter@amd.com>
Date: Mon, 27 Jul 2009 19:43:52 +0200
Subject: [PATCH 0127/1153] x86: fix section mismatch for i386 init code

Startup code for i386 in arch/x86/kernel/head_32.S is using the
reference variable initial_code that is located in the .cpuinit.data
section. If CONFIG_HOTPLUG_CPU is enabled, startup code is not in an
init section and can be called later too. In this case the reference
initial_code must be kept too. This patch fixes this. See below for
the section mismatch warning.

 WARNING: vmlinux.o(.cpuinit.data+0x0): Section mismatch in reference
 from the variable initial_code to the function
 .init.text:i386_start_kernel()
 The variable __cpuinitdata initial_code references
 a function __init i386_start_kernel().
 If i386_start_kernel is only used by initial_code then
 annotate i386_start_kernel with a matching annotation.

Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <1248716632-26844-1-git-send-email-robert.richter@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
---
 arch/x86/kernel/head_32.S | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/x86/kernel/head_32.S b/arch/x86/kernel/head_32.S
index 8663afb5653..0d98a01cbdb 100644
--- a/arch/x86/kernel/head_32.S
+++ b/arch/x86/kernel/head_32.S
@@ -602,7 +602,11 @@ ignore_int:
 #endif
 	iret
 
-.section .cpuinit.data,"wa"
+#ifndef CONFIG_HOTPLUG_CPU
+	__CPUINITDATA
+#else
+	__REFDATA
+#endif
 .align 4
 ENTRY(initial_code)
 	.long i386_start_kernel
-- 
GitLab


From 7cb7f45c7feef43c8f71f5cfedfc0b19be2142f7 Mon Sep 17 00:00:00 2001
From: Len Brown <len.brown@intel.com>
Date: Mon, 27 Jul 2009 18:42:38 -0400
Subject: [PATCH 0128/1153] Revert "ACPICA: Remove obsolete
 acpi_os_validate_address interface"

This reverts commit f9ca058430333c9a24c5ca926aa445125f88df18.

which caused a regression:

http://bugzilla.kernel.org/show_bug.cgi?id=13620

Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/acpi/acpica/acobject.h |  1 +
 drivers/acpi/acpica/dsopcode.c | 24 ++++++++++++++++++++++++
 drivers/acpi/acpica/exfldio.c  |  6 ++++++
 include/acpi/acpiosxf.h        |  4 ++++
 4 files changed, 35 insertions(+)

diff --git a/drivers/acpi/acpica/acobject.h b/drivers/acpi/acpica/acobject.h
index 544dcf83492..eb6f038b03d 100644
--- a/drivers/acpi/acpica/acobject.h
+++ b/drivers/acpi/acpica/acobject.h
@@ -97,6 +97,7 @@
 #define AOPOBJ_OBJECT_INITIALIZED   0x08
 #define AOPOBJ_SETUP_COMPLETE       0x10
 #define AOPOBJ_SINGLE_DATUM         0x20
+#define AOPOBJ_INVALID              0x40	/* Used if host OS won't allow an op_region address */
 
 /******************************************************************************
  *
diff --git a/drivers/acpi/acpica/dsopcode.c b/drivers/acpi/acpica/dsopcode.c
index 584d766e6f1..b79978f7bc7 100644
--- a/drivers/acpi/acpica/dsopcode.c
+++ b/drivers/acpi/acpica/dsopcode.c
@@ -397,6 +397,30 @@ acpi_status acpi_ds_get_region_arguments(union acpi_operand_object *obj_desc)
 	status = acpi_ds_execute_arguments(node, acpi_ns_get_parent_node(node),
 					   extra_desc->extra.aml_length,
 					   extra_desc->extra.aml_start);
+	if (ACPI_FAILURE(status)) {
+		return_ACPI_STATUS(status);
+	}
+
+	/* Validate the region address/length via the host OS */
+
+	status = acpi_os_validate_address(obj_desc->region.space_id,
+					  obj_desc->region.address,
+					  (acpi_size) obj_desc->region.length,
+					  acpi_ut_get_node_name(node));
+
+	if (ACPI_FAILURE(status)) {
+		/*
+		 * Invalid address/length. We will emit an error message and mark
+		 * the region as invalid, so that it will cause an additional error if
+		 * it is ever used. Then return AE_OK.
+		 */
+		ACPI_EXCEPTION((AE_INFO, status,
+				"During address validation of OpRegion [%4.4s]",
+				node->name.ascii));
+		obj_desc->common.flags |= AOPOBJ_INVALID;
+		status = AE_OK;
+	}
+
 	return_ACPI_STATUS(status);
 }
 
diff --git a/drivers/acpi/acpica/exfldio.c b/drivers/acpi/acpica/exfldio.c
index d4075b82102..6687be167f5 100644
--- a/drivers/acpi/acpica/exfldio.c
+++ b/drivers/acpi/acpica/exfldio.c
@@ -113,6 +113,12 @@ acpi_ex_setup_region(union acpi_operand_object *obj_desc,
 		}
 	}
 
+	/* Exit if Address/Length have been disallowed by the host OS */
+
+	if (rgn_desc->common.flags & AOPOBJ_INVALID) {
+		return_ACPI_STATUS(AE_AML_ILLEGAL_ADDRESS);
+	}
+
 	/*
 	 * Exit now for SMBus address space, it has a non-linear address space
 	 * and the request cannot be directly validated
diff --git a/include/acpi/acpiosxf.h b/include/acpi/acpiosxf.h
index 3e798593b17..ab0b85cf21f 100644
--- a/include/acpi/acpiosxf.h
+++ b/include/acpi/acpiosxf.h
@@ -242,6 +242,10 @@ acpi_os_derive_pci_id(acpi_handle rhandle,
 acpi_status acpi_os_validate_interface(char *interface);
 acpi_status acpi_osi_invalidate(char* interface);
 
+acpi_status
+acpi_os_validate_address(u8 space_id, acpi_physical_address address,
+			 acpi_size length, char *name);
+
 u64 acpi_os_get_timer(void);
 
 acpi_status acpi_os_signal(u32 function, void *info);
-- 
GitLab


From 626f5cefc60b281a00db1402b82deff82080c70a Mon Sep 17 00:00:00 2001
From: Takashi Iwai <tiwai@suse.de>
Date: Tue, 28 Jul 2009 00:54:39 +0200
Subject: [PATCH 0129/1153] ALSA: hda - Add quirk for Dell Studio 1555

Added a quirk entry for Dell Studio 1555.

Reference: Novell bnc#525244
	https://bugzilla.novell.com/show_bug.cgi?id=525244

Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/patch_sigmatel.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c
index 512f3b9b9a4..5383d8cff88 100644
--- a/sound/pci/hda/patch_sigmatel.c
+++ b/sound/pci/hda/patch_sigmatel.c
@@ -1809,6 +1809,8 @@ static struct snd_pci_quirk stac92hd73xx_cfg_tbl[] = {
 				"Dell Studio 1537", STAC_DELL_M6_DMIC),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x02a0,
 				"Dell Studio 17", STAC_DELL_M6_DMIC),
+	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x02be,
+				"Dell Studio 1555", STAC_DELL_M6_DMIC),
 	{} /* terminator */
 };
 
-- 
GitLab


From 7b91e2661addd8e2419cb45f6a322aa5dab9bcee Mon Sep 17 00:00:00 2001
From: Jeff Layton <jlayton@redhat.com>
Date: Thu, 23 Jul 2009 15:22:30 -0400
Subject: [PATCH 0130/1153] cifs: fix error handling in mount-time DFS referral
 chasing code

If the referral is malformed or the hostname can't be resolved, then
the current code generates an oops. Fix it to handle these errors
gracefully.

Reported-by: Sandro Mathys <sm@sandro-mathys.ch>
Acked-by: Igor Mammedov <niallain@gmail.com>
CC: Stable <stable@kernel.org>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
---
 fs/cifs/cifs_dfs_ref.c | 12 +++++++++---
 fs/cifs/connect.c      | 13 ++++++++++---
 2 files changed, 19 insertions(+), 6 deletions(-)

diff --git a/fs/cifs/cifs_dfs_ref.c b/fs/cifs/cifs_dfs_ref.c
index 3bb11be8b6a..606912d8f2a 100644
--- a/fs/cifs/cifs_dfs_ref.c
+++ b/fs/cifs/cifs_dfs_ref.c
@@ -55,7 +55,7 @@ void cifs_dfs_release_automount_timer(void)
  * i.e. strips from UNC trailing path that is not part of share
  * name and fixup missing '\' in the begining of DFS node refferal
  * if neccessary.
- * Returns pointer to share name on success or NULL on error.
+ * Returns pointer to share name on success or ERR_PTR on error.
  * Caller is responsible for freeing returned string.
  */
 static char *cifs_get_share_name(const char *node_name)
@@ -68,7 +68,7 @@ static char *cifs_get_share_name(const char *node_name)
 	UNC = kmalloc(len+2 /*for term null and additional \ if it's missed */,
 			 GFP_KERNEL);
 	if (!UNC)
-		return NULL;
+		return ERR_PTR(-ENOMEM);
 
 	/* get share name and server name */
 	if (node_name[1] != '\\') {
@@ -87,7 +87,7 @@ static char *cifs_get_share_name(const char *node_name)
 		cERROR(1, ("%s: no server name end in node name: %s",
 			__func__, node_name));
 		kfree(UNC);
-		return NULL;
+		return ERR_PTR(-EINVAL);
 	}
 
 	/* find sharename end */
@@ -133,6 +133,12 @@ char *cifs_compose_mount_options(const char *sb_mountdata,
 		return ERR_PTR(-EINVAL);
 
 	*devname = cifs_get_share_name(ref->node_name);
+	if (IS_ERR(*devname)) {
+		rc = PTR_ERR(*devname);
+		*devname = NULL;
+		goto compose_mount_options_err;
+	}
+
 	rc = dns_resolve_server_name_to_ip(*devname, &srvIP);
 	if (rc != 0) {
 		cERROR(1, ("%s: Failed to resolve server part of %s to IP: %d",
diff --git a/fs/cifs/connect.c b/fs/cifs/connect.c
index fc44d316d0b..f2486889b7b 100644
--- a/fs/cifs/connect.c
+++ b/fs/cifs/connect.c
@@ -2544,11 +2544,20 @@ remote_path_check:
 
 			if (mount_data != mount_data_global)
 				kfree(mount_data);
+
 			mount_data = cifs_compose_mount_options(
 					cifs_sb->mountdata, full_path + 1,
 					referrals, &fake_devname);
-			kfree(fake_devname);
+
 			free_dfs_info_array(referrals, num_referrals);
+			kfree(fake_devname);
+			kfree(full_path);
+
+			if (IS_ERR(mount_data)) {
+				rc = PTR_ERR(mount_data);
+				mount_data = NULL;
+				goto mount_fail_check;
+			}
 
 			if (tcon)
 				cifs_put_tcon(tcon);
@@ -2556,8 +2565,6 @@ remote_path_check:
 				cifs_put_smb_ses(pSesInfo);
 
 			cleanup_volume_info(&volume_info);
-			FreeXid(xid);
-			kfree(full_path);
 			referral_walks_count++;
 			goto try_mount_again;
 		}
-- 
GitLab


From 9a926d86b29a25456f1dd8c9df938e151b1c3978 Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Mon, 27 Jul 2009 18:10:28 -0700
Subject: [PATCH 0131/1153] sparc64: Sign extend length arg to truncate
 syscalls when compat.

The first thing sys_truncate() and sys_ftruncate() do is sign extend
the unsigned length arg to a signed type.

Thanks to Benjamin Herrenschmidt for the tip.

Signed-off-by: David S. Miller <davem@davemloft.net>
---
 arch/sparc/kernel/sys32.S      | 2 ++
 arch/sparc/kernel/systbls_64.S | 4 ++--
 2 files changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/sparc/kernel/sys32.S b/arch/sparc/kernel/sys32.S
index f061c4dda9e..577f8fab8b6 100644
--- a/arch/sparc/kernel/sys32.S
+++ b/arch/sparc/kernel/sys32.S
@@ -138,6 +138,8 @@ SIGN2(sys32_splice, sys_splice, %o0, %o1)
 SIGN2(sys32_sync_file_range, compat_sync_file_range, %o0, %o5)
 SIGN2(sys32_tee, sys_tee, %o0, %o1)
 SIGN1(sys32_vmsplice, compat_sys_vmsplice, %o0)
+SIGN1(sys32_truncate, sys_truncate, %o1)
+SIGN1(sys32_ftruncate, sys_ftruncate, %o1)
 
 	.globl		sys32_mmap2
 sys32_mmap2:
diff --git a/arch/sparc/kernel/systbls_64.S b/arch/sparc/kernel/systbls_64.S
index 6b3ee88e253..2ee7250ba7a 100644
--- a/arch/sparc/kernel/systbls_64.S
+++ b/arch/sparc/kernel/systbls_64.S
@@ -43,8 +43,8 @@ sys_call_table32:
 /*110*/	.word sys_setresgid, sys_getresgid, sys_setregid, sys_nis_syscall, sys_nis_syscall
 	.word sys32_getgroups, compat_sys_gettimeofday, sys32_getrusage, sys_nis_syscall, sys_getcwd
 /*120*/	.word compat_sys_readv, compat_sys_writev, compat_sys_settimeofday, sys_fchown16, sys_fchmod
-	.word sys_nis_syscall, sys_setreuid16, sys_setregid16, sys_rename, sys_truncate
-/*130*/	.word sys_ftruncate, sys_flock, compat_sys_lstat64, sys_nis_syscall, sys_nis_syscall
+	.word sys_nis_syscall, sys_setreuid16, sys_setregid16, sys_rename, sys32_truncate
+/*130*/	.word sys32_ftruncate, sys_flock, compat_sys_lstat64, sys_nis_syscall, sys_nis_syscall
 	.word sys_nis_syscall, sys32_mkdir, sys_rmdir, compat_sys_utimes, compat_sys_stat64
 /*140*/	.word sys32_sendfile64, sys_nis_syscall, sys32_futex, sys_gettid, compat_sys_getrlimit
 	.word compat_sys_setrlimit, sys_pivot_root, sys32_prctl, sys_pciconfig_read, sys_pciconfig_write
-- 
GitLab


From 27fed4175acf81ddd91d9a4ee2fd298981f60295 Mon Sep 17 00:00:00 2001
From: Stephen Hemminger <shemminger@vyatta.com>
Date: Mon, 27 Jul 2009 18:39:45 -0700
Subject: [PATCH 0132/1153] ip: fix logic of reverse path filter sysctl

Even though reverse path filter was changed from simple boolean to
trinary control, the loose mode only works if both all and device are
configured because of this logic error.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 include/linux/inetdevice.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/inetdevice.h b/include/linux/inetdevice.h
index acef2a770b6..ad27c7da879 100644
--- a/include/linux/inetdevice.h
+++ b/include/linux/inetdevice.h
@@ -82,7 +82,7 @@ static inline void ipv4_devconf_setall(struct in_device *in_dev)
 
 #define IN_DEV_FORWARD(in_dev)		IN_DEV_CONF_GET((in_dev), FORWARDING)
 #define IN_DEV_MFORWARD(in_dev)		IN_DEV_ANDCONF((in_dev), MC_FORWARDING)
-#define IN_DEV_RPFILTER(in_dev)		IN_DEV_ANDCONF((in_dev), RP_FILTER)
+#define IN_DEV_RPFILTER(in_dev)		IN_DEV_MAXCONF((in_dev), RP_FILTER)
 #define IN_DEV_SOURCE_ROUTE(in_dev)	IN_DEV_ANDCONF((in_dev), \
 						       ACCEPT_SOURCE_ROUTE)
 #define IN_DEV_BOOTP_RELAY(in_dev)	IN_DEV_ANDCONF((in_dev), BOOTP_RELAY)
-- 
GitLab


From 48f5690d45b79ffeedc5ab24243b576056f1d2ff Mon Sep 17 00:00:00 2001
From: unsik Kim <donari75@gmail.com>
Date: Tue, 28 Jul 2009 08:52:06 +0200
Subject: [PATCH 0133/1153] mg_disk: remove prohibited sleep operation

mflash's polling driver operate in standard request_fn_proc's context,
sleep in this isn't permitted.

Signed-off-by: unsik Kim <donari75@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 drivers/block/mg_disk.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c
index f703f547824..5b120eab2ba 100644
--- a/drivers/block/mg_disk.c
+++ b/drivers/block/mg_disk.c
@@ -245,8 +245,6 @@ static unsigned int mg_wait(struct mg_host *host, u32 expect, u32 msec)
 			mg_dump_status("not ready", status, host);
 			return MG_ERR_INV_STAT;
 		}
-		if (prv_data->use_polling)
-			msleep(1);
 
 		status = inb((unsigned long)host->dev_base + MG_REG_STATUS);
 	} while (time_before(cur_jiffies, expire));
-- 
GitLab


From eb32baec15c38ae6f06cb898a9f791578c5f8c79 Mon Sep 17 00:00:00 2001
From: unsik Kim <donari75@gmail.com>
Date: Tue, 28 Jul 2009 08:52:07 +0200
Subject: [PATCH 0134/1153] mg_disk: fix reading invalid status when use
 polling driver

When using polling driver, little delay is required to access
status register. Without this, host might read invalid status.

Signed-off-by: unsik Kim <donari75@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 drivers/block/mg_disk.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c
index 5b120eab2ba..6440d594541 100644
--- a/drivers/block/mg_disk.c
+++ b/drivers/block/mg_disk.c
@@ -219,6 +219,16 @@ static unsigned int mg_wait(struct mg_host *host, u32 expect, u32 msec)
 	host->error = MG_ERR_NONE;
 	expire = jiffies + msecs_to_jiffies(msec);
 
+	/* These 2 times dummy status read prevents reading invalid
+	 * status. A very little time (3 times of mflash operating clk)
+	 * is required for busy bit is set. Use dummy read instead of
+	 * busy wait, because mflash's PLL is machine dependent.
+	 */
+	if (prv_data->use_polling) {
+		status = inb((unsigned long)host->dev_base + MG_REG_STATUS);
+		status = inb((unsigned long)host->dev_base + MG_REG_STATUS);
+	}
+
 	status = inb((unsigned long)host->dev_base + MG_REG_STATUS);
 
 	do {
-- 
GitLab


From 394c6cc63c1d6900ad7498a3221a1d48fc00c4fa Mon Sep 17 00:00:00 2001
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Tue, 28 Jul 2009 08:56:34 +0200
Subject: [PATCH 0135/1153] mg_disk: fix issue with data integrity on error in
 mg_write()

We cannot acknowledge the sector write before checking its status
(which is done on the next loop iteration) and we also need to do
the final status register check after writing the last sector.

Fix mg_write() to match mg_write_intr() in this regard.

While at it:
- add mg_read_one() and mg_write_one() helpers
- always use MG_SECTOR_SIZE and remove MG_STORAGE_BUFFER_SIZE

[bart: thanks to Tejun for porting the patch over recent block changes]

Cc: unsik Kim <donari75@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

===================================================================
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 drivers/block/mg_disk.c | 89 ++++++++++++++++++++++-------------------
 1 file changed, 47 insertions(+), 42 deletions(-)

diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c
index 6440d594541..19917d5481b 100644
--- a/drivers/block/mg_disk.c
+++ b/drivers/block/mg_disk.c
@@ -36,7 +36,6 @@
 
 /* Register offsets */
 #define MG_BUFF_OFFSET			0x8000
-#define MG_STORAGE_BUFFER_SIZE		0x200
 #define MG_REG_OFFSET			0xC000
 #define MG_REG_FEATURE			(MG_REG_OFFSET + 2)	/* write case */
 #define MG_REG_ERROR			(MG_REG_OFFSET + 2)	/* read case */
@@ -477,9 +476,18 @@ static unsigned int mg_out(struct mg_host *host,
 	return MG_ERR_NONE;
 }
 
+static void mg_read_one(struct mg_host *host, struct request *req)
+{
+	u16 *buff = (u16 *)req->buffer;
+	u32 i;
+
+	for (i = 0; i < MG_SECTOR_SIZE >> 1; i++)
+		*buff++ = inw((unsigned long)host->dev_base + MG_BUFF_OFFSET +
+			      (i << 1));
+}
+
 static void mg_read(struct request *req)
 {
-	u32 j;
 	struct mg_host *host = req->rq_disk->private_data;
 
 	if (mg_out(host, blk_rq_pos(req), blk_rq_sectors(req),
@@ -490,26 +498,33 @@ static void mg_read(struct request *req)
 	       blk_rq_sectors(req), blk_rq_pos(req), req->buffer);
 
 	do {
-		u16 *buff = (u16 *)req->buffer;
-
 		if (mg_wait(host, ATA_DRQ,
 			    MG_TMAX_WAIT_RD_DRQ) != MG_ERR_NONE) {
 			mg_bad_rw_intr(host);
 			return;
 		}
-		for (j = 0; j < MG_SECTOR_SIZE >> 1; j++)
-			*buff++ = inw((unsigned long)host->dev_base +
-				      MG_BUFF_OFFSET + (j << 1));
+
+		mg_read_one(host, req);
 
 		outb(MG_CMD_RD_CONF, (unsigned long)host->dev_base +
 				MG_REG_COMMAND);
 	} while (mg_end_request(host, 0, MG_SECTOR_SIZE));
 }
 
+static void mg_write_one(struct mg_host *host, struct request *req)
+{
+	u16 *buff = (u16 *)req->buffer;
+	u32 i;
+
+	for (i = 0; i < MG_SECTOR_SIZE >> 1; i++)
+		outw(*buff++, (unsigned long)host->dev_base + MG_BUFF_OFFSET +
+		     (i << 1));
+}
+
 static void mg_write(struct request *req)
 {
-	u32 j;
 	struct mg_host *host = req->rq_disk->private_data;
+	bool rem;
 
 	if (mg_out(host, blk_rq_pos(req), blk_rq_sectors(req),
 		   MG_CMD_WR, NULL) != MG_ERR_NONE) {
@@ -520,27 +535,37 @@ static void mg_write(struct request *req)
 	MG_DBG("requested %d sects (from %ld), buffer=0x%p\n",
 	       blk_rq_sectors(req), blk_rq_pos(req), req->buffer);
 
-	do {
-		u16 *buff = (u16 *)req->buffer;
+	if (mg_wait(host, ATA_DRQ,
+		    MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) {
+		mg_bad_rw_intr(host);
+		return;
+	}
+
+	mg_write_one(host, req);
+
+	outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + MG_REG_COMMAND);
 
-	if (mg_wait(host, ATA_DRQ, MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) {
+	do {
+		if (blk_rq_sectors(req) > 1 &&
+		     mg_wait(host, ATA_DRQ,
+			     MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) {
 			mg_bad_rw_intr(host);
 			return;
 		}
-		for (j = 0; j < MG_SECTOR_SIZE >> 1; j++)
-			outw(*buff++, (unsigned long)host->dev_base +
-				      MG_BUFF_OFFSET + (j << 1));
 
-		outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base +
-				MG_REG_COMMAND);
-	} while (mg_end_request(host, 0, MG_SECTOR_SIZE));
+		rem = mg_end_request(host, 0, MG_SECTOR_SIZE);
+		if (rem)
+			mg_write_one(host, req);
+
+		outb(MG_CMD_WR_CONF,
+		     (unsigned long)host->dev_base + MG_REG_COMMAND);
+	} while (rem);
 }
 
 static void mg_read_intr(struct mg_host *host)
 {
 	struct request *req = host->req;
 	u32 i;
-	u16 *buff;
 
 	/* check status */
 	do {
@@ -558,13 +583,7 @@ static void mg_read_intr(struct mg_host *host)
 	return;
 
 ok_to_read:
-	/* get current segment of request */
-	buff = (u16 *)req->buffer;
-
-	/* read 1 sector */
-	for (i = 0; i < MG_SECTOR_SIZE >> 1; i++)
-		*buff++ = inw((unsigned long)host->dev_base + MG_BUFF_OFFSET +
-			      (i << 1));
+	mg_read_one(host, req);
 
 	MG_DBG("sector %ld, remaining=%ld, buffer=0x%p\n",
 	       blk_rq_pos(req), blk_rq_sectors(req) - 1, req->buffer);
@@ -583,8 +602,7 @@ ok_to_read:
 static void mg_write_intr(struct mg_host *host)
 {
 	struct request *req = host->req;
-	u32 i, j;
-	u16 *buff;
+	u32 i;
 	bool rem;
 
 	/* check status */
@@ -605,12 +623,7 @@ static void mg_write_intr(struct mg_host *host)
 ok_to_write:
 	if ((rem = mg_end_request(host, 0, MG_SECTOR_SIZE))) {
 		/* write 1 sector and set handler if remains */
-		buff = (u16 *)req->buffer;
-		for (j = 0; j < MG_STORAGE_BUFFER_SIZE >> 1; j++) {
-			outw(*buff, (unsigned long)host->dev_base +
-					MG_BUFF_OFFSET + (j << 1));
-			buff++;
-		}
+		mg_write_one(host, req);
 		MG_DBG("sector %ld, remaining=%ld, buffer=0x%p\n",
 		       blk_rq_pos(req), blk_rq_sectors(req), req->buffer);
 		host->mg_do_intr = mg_write_intr;
@@ -675,9 +688,6 @@ static unsigned int mg_issue_req(struct request *req,
 		unsigned int sect_num,
 		unsigned int sect_cnt)
 {
-	u16 *buff;
-	u32 i;
-
 	switch (rq_data_dir(req)) {
 	case READ:
 		if (mg_out(host, sect_num, sect_cnt, MG_CMD_RD, &mg_read_intr)
@@ -701,12 +711,7 @@ static unsigned int mg_issue_req(struct request *req,
 			mg_bad_rw_intr(host);
 			return host->error;
 		}
-		buff = (u16 *)req->buffer;
-		for (i = 0; i < MG_SECTOR_SIZE >> 1; i++) {
-			outw(*buff, (unsigned long)host->dev_base +
-					MG_BUFF_OFFSET + (i << 1));
-			buff++;
-		}
+		mg_write_one(host, req);
 		mod_timer(&host->timer, jiffies + 3 * HZ);
 		outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base +
 				MG_REG_COMMAND);
-- 
GitLab


From a85a00a699740f6f9863f88aef22060fe1534681 Mon Sep 17 00:00:00 2001
From: unsik Kim <donari75@gmail.com>
Date: Tue, 28 Jul 2009 08:57:33 +0200
Subject: [PATCH 0136/1153] mg_disk: Add missing ready status check on
 mg_write()

When last sector is written, ready bit of status register should be
checked.

Signed-off-by: unsik Kim <donari75@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 drivers/block/mg_disk.c | 32 +++++++++++++++-----------------
 1 file changed, 15 insertions(+), 17 deletions(-)

diff --git a/drivers/block/mg_disk.c b/drivers/block/mg_disk.c
index 19917d5481b..6d7fbaa9224 100644
--- a/drivers/block/mg_disk.c
+++ b/drivers/block/mg_disk.c
@@ -524,16 +524,16 @@ static void mg_write_one(struct mg_host *host, struct request *req)
 static void mg_write(struct request *req)
 {
 	struct mg_host *host = req->rq_disk->private_data;
-	bool rem;
+	unsigned int rem = blk_rq_sectors(req);
 
-	if (mg_out(host, blk_rq_pos(req), blk_rq_sectors(req),
+	if (mg_out(host, blk_rq_pos(req), rem,
 		   MG_CMD_WR, NULL) != MG_ERR_NONE) {
 		mg_bad_rw_intr(host);
 		return;
 	}
 
 	MG_DBG("requested %d sects (from %ld), buffer=0x%p\n",
-	       blk_rq_sectors(req), blk_rq_pos(req), req->buffer);
+	       rem, blk_rq_pos(req), req->buffer);
 
 	if (mg_wait(host, ATA_DRQ,
 		    MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) {
@@ -541,25 +541,23 @@ static void mg_write(struct request *req)
 		return;
 	}
 
-	mg_write_one(host, req);
+	do {
+		mg_write_one(host, req);
 
-	outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base + MG_REG_COMMAND);
+		outb(MG_CMD_WR_CONF, (unsigned long)host->dev_base +
+				MG_REG_COMMAND);
 
-	do {
-		if (blk_rq_sectors(req) > 1 &&
-		     mg_wait(host, ATA_DRQ,
-			     MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) {
+		rem--;
+		if (rem > 1 && mg_wait(host, ATA_DRQ,
+					MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) {
+			mg_bad_rw_intr(host);
+			return;
+		} else if (mg_wait(host, MG_STAT_READY,
+					MG_TMAX_WAIT_WR_DRQ) != MG_ERR_NONE) {
 			mg_bad_rw_intr(host);
 			return;
 		}
-
-		rem = mg_end_request(host, 0, MG_SECTOR_SIZE);
-		if (rem)
-			mg_write_one(host, req);
-
-		outb(MG_CMD_WR_CONF,
-		     (unsigned long)host->dev_base + MG_REG_COMMAND);
-	} while (rem);
+	} while (mg_end_request(host, 0, MG_SECTOR_SIZE));
 }
 
 static void mg_read_intr(struct mg_host *host)
-- 
GitLab


From a4e7d46407d73f35d217013b363b79a8f8eafcaa Mon Sep 17 00:00:00 2001
From: Jens Axboe <jens.axboe@oracle.com>
Date: Tue, 28 Jul 2009 09:07:29 +0200
Subject: [PATCH 0137/1153] block: always assign default lock to queues

Move the assignment of a default lock below blk_init_queue() to
blk_queue_make_request(), so we also get to set the default lock
for ->make_request_fn() based drivers. This is important since the
queue flag locking requires a lock to be in place.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 block/blk-core.c     | 7 -------
 block/blk-settings.c | 7 +++++++
 2 files changed, 7 insertions(+), 7 deletions(-)

diff --git a/block/blk-core.c b/block/blk-core.c
index 4b45435c6ea..a0c340d239b 100644
--- a/block/blk-core.c
+++ b/block/blk-core.c
@@ -575,13 +575,6 @@ blk_init_queue_node(request_fn_proc *rfn, spinlock_t *lock, int node_id)
 		return NULL;
 	}
 
-	/*
-	 * if caller didn't supply a lock, they get per-queue locking with
-	 * our embedded lock
-	 */
-	if (!lock)
-		lock = &q->__queue_lock;
-
 	q->request_fn		= rfn;
 	q->prep_rq_fn		= NULL;
 	q->unplug_fn		= generic_unplug_device;
diff --git a/block/blk-settings.c b/block/blk-settings.c
index bd582a7f531..8a3ea3bba10 100644
--- a/block/blk-settings.c
+++ b/block/blk-settings.c
@@ -164,6 +164,13 @@ void blk_queue_make_request(struct request_queue *q, make_request_fn *mfn)
 
 	blk_set_default_limits(&q->limits);
 
+	/*
+	 * If the caller didn't supply a lock, fall back to our embedded
+	 * per-queue locks
+	 */
+	if (!q->queue_lock)
+		q->queue_lock = &q->__queue_lock;
+
 	/*
 	 * by default assume old behaviour and bounce for any highmem page
 	 */
-- 
GitLab


From 3839e4b29b4385e4b31075e7805683e2aa2a8103 Mon Sep 17 00:00:00 2001
From: Xiaotian Feng <dfeng@redhat.com>
Date: Tue, 28 Jul 2009 09:11:14 +0200
Subject: [PATCH 0138/1153] block: fix improper kobject release in
 blk_integrity_unregister

blk_integrity_unregister should use kobject_put to release the kobject,
otherwise after bi is freed, memory of bi->kobj->name is leaked.

Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 block/blk-integrity.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/block/blk-integrity.c b/block/blk-integrity.c
index 73e28d35568..15c630813b1 100644
--- a/block/blk-integrity.c
+++ b/block/blk-integrity.c
@@ -379,6 +379,7 @@ void blk_integrity_unregister(struct gendisk *disk)
 
 	kobject_uevent(&bi->kobj, KOBJ_REMOVE);
 	kobject_del(&bi->kobj);
+	kobject_put(&bi->kobj);
 	kmem_cache_free(integrity_cachep, bi);
 	disk->integrity = NULL;
 }
-- 
GitLab


From 8666f8deec75a8dce15edd35ec33d29ef79cdb08 Mon Sep 17 00:00:00 2001
From: Sascha Hauer <s.hauer@pengutronix.de>
Date: Fri, 24 Jul 2009 17:30:50 +0200
Subject: [PATCH 0139/1153] mx27 defconfig update

- enable MX27_3DS and MX27LITE Board
- enable MXC nand driver
- enable UBI support

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/configs/mx27_defconfig | 270 ++++++++++++++++++++++----------
 1 file changed, 185 insertions(+), 85 deletions(-)

diff --git a/arch/arm/configs/mx27_defconfig b/arch/arm/configs/mx27_defconfig
index 083516cd0d7..75263a83741 100644
--- a/arch/arm/configs/mx27_defconfig
+++ b/arch/arm/configs/mx27_defconfig
@@ -1,15 +1,15 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc1
-# Wed Apr  8 10:18:06 2009
+# Linux kernel version: 2.6.31-rc4
+# Fri Jul 24 16:08:06 2009
 #
 CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
 CONFIG_SYS_SUPPORTS_APM_EMULATION=y
 CONFIG_GENERIC_GPIO=y
 CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
 CONFIG_GENERIC_HARDIRQS=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
@@ -18,14 +18,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_HARDIRQS_SW_RESEND=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
 CONFIG_GENERIC_HWEIGHT=y
 CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_ARCH_MTD_XIP=y
 CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 CONFIG_VECTORS_BASE=0xffff0000
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -85,7 +84,12 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+
+#
+# Performance Counters
+#
 CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_COMPAT_BRK is not set
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -99,6 +103,12 @@ CONFIG_KPROBES=y
 CONFIG_KRETPROBES=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 CONFIG_HAVE_GENERIC_DMA_COHERENT=y
 CONFIG_SLABINFO=y
@@ -111,7 +121,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -138,13 +148,14 @@ CONFIG_FREEZER=y
 # CONFIG_ARCH_VERSATILE is not set
 # CONFIG_ARCH_AT91 is not set
 # CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
 # CONFIG_ARCH_EBSA110 is not set
 # CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_GEMINI is not set
 # CONFIG_ARCH_FOOTBRIDGE is not set
+CONFIG_ARCH_MXC=y
+# CONFIG_ARCH_STMP3XXX is not set
 # CONFIG_ARCH_NETX is not set
 # CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
 # CONFIG_ARCH_IOP13XX is not set
 # CONFIG_ARCH_IOP32X is not set
 # CONFIG_ARCH_IOP33X is not set
@@ -153,25 +164,25 @@ CONFIG_FREEZER=y
 # CONFIG_ARCH_IXP4XX is not set
 # CONFIG_ARCH_L7200 is not set
 # CONFIG_ARCH_KIRKWOOD is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
 # CONFIG_ARCH_LOKI is not set
 # CONFIG_ARCH_MV78XX0 is not set
-CONFIG_ARCH_MXC=y
 # CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
 # CONFIG_ARCH_PNX4008 is not set
 # CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_MSM is not set
 # CONFIG_ARCH_RPC is not set
 # CONFIG_ARCH_SA1100 is not set
 # CONFIG_ARCH_S3C2410 is not set
 # CONFIG_ARCH_S3C64XX is not set
 # CONFIG_ARCH_SHARK is not set
 # CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
 # CONFIG_ARCH_DAVINCI is not set
 # CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM is not set
-# CONFIG_ARCH_W90X900 is not set
 
 #
 # Freescale MXC Implementations
@@ -188,6 +199,8 @@ CONFIG_MACH_MX27=y
 CONFIG_MACH_MX27ADS=y
 CONFIG_MACH_PCM038=y
 CONFIG_MACH_PCM970_BASEBOARD=y
+CONFIG_MACH_MX27_3DS=y
+CONFIG_MACH_MX27LITE=y
 CONFIG_MXC_IRQ_PRIOR=y
 CONFIG_MXC_PWM=y
 
@@ -213,7 +226,6 @@ CONFIG_ARM_THUMB=y
 # CONFIG_CPU_DCACHE_DISABLE is not set
 # CONFIG_CPU_DCACHE_WRITETHROUGH is not set
 # CONFIG_CPU_CACHE_ROUND_ROBIN is not set
-# CONFIG_OUTER_CACHE is not set
 CONFIG_COMMON_CLKDEV=y
 
 #
@@ -238,7 +250,6 @@ CONFIG_PREEMPT=y
 CONFIG_HZ=100
 CONFIG_AEABI=y
 CONFIG_OABI_COMPAT=y
-CONFIG_ARCH_FLATMEM_HAS_HOLES=y
 # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
 # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
 # CONFIG_HIGHMEM is not set
@@ -253,10 +264,11 @@ CONFIG_SPLIT_PTLOCK_CPUS=4096
 # CONFIG_PHYS_ADDR_T_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
 
 #
 # Boot options
@@ -361,6 +373,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -474,7 +487,16 @@ CONFIG_MTD_PHYSMAP=y
 # CONFIG_MTD_DOC2000 is not set
 # CONFIG_MTD_DOC2001 is not set
 # CONFIG_MTD_DOC2001PLUS is not set
-# CONFIG_MTD_NAND is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+CONFIG_MTD_NAND_MXC=y
 # CONFIG_MTD_ONENAND is not set
 
 #
@@ -485,7 +507,15 @@ CONFIG_MTD_PHYSMAP=y
 #
 # UBI - Unsorted block images
 #
-# CONFIG_MTD_UBI is not set
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_COW_COMMON is not set
@@ -494,7 +524,21 @@ CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_RAM is not set
 # CONFIG_CDROM_PKTCDVD is not set
 # CONFIG_ATA_OVER_ETH is not set
-# CONFIG_MISC_DEVICES is not set
+# CONFIG_MG_DISK is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+CONFIG_EEPROM_AT24=y
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+# CONFIG_EEPROM_93CX6 is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -508,7 +552,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_ATA is not set
 # CONFIG_MD is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -534,6 +577,8 @@ CONFIG_NET_ETHERNET=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
 CONFIG_FEC=y
 # CONFIG_FEC2 is not set
 # CONFIG_NETDEV_1000 is not set
@@ -580,6 +625,11 @@ CONFIG_INPUT_EVDEV=y
 # CONFIG_INPUT_TABLET is not set
 CONFIG_INPUT_TOUCHSCREEN=y
 # CONFIG_TOUCHSCREEN_ADS7846 is not set
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
 # CONFIG_TOUCHSCREEN_FUJITSU is not set
 # CONFIG_TOUCHSCREEN_GUNZE is not set
 # CONFIG_TOUCHSCREEN_ELO is not set
@@ -592,6 +642,7 @@ CONFIG_INPUT_TOUCHSCREEN=y
 # CONFIG_TOUCHSCREEN_TOUCHWIN is not set
 # CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
 # CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
 # CONFIG_INPUT_MISC is not set
 
 #
@@ -644,6 +695,7 @@ CONFIG_I2C_HELPER_AUTO=y
 #
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_GPIO is not set
 CONFIG_I2C_IMX=y
 # CONFIG_I2C_OCORES is not set
@@ -668,7 +720,6 @@ CONFIG_I2C_IMX=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -719,6 +770,7 @@ CONFIG_W1=y
 #
 # CONFIG_W1_MASTER_DS2482 is not set
 CONFIG_W1_MASTER_MXC=y
+# CONFIG_W1_MASTER_DS1WM is not set
 # CONFIG_W1_MASTER_GPIO is not set
 
 #
@@ -753,54 +805,16 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_TPS65010 is not set
 # CONFIG_TWL4030_CORE is not set
 # CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
 # CONFIG_MFD_TC6393XB is not set
 # CONFIG_PMIC_DA903X is not set
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-CONFIG_VIDEO_DEV=y
-CONFIG_VIDEO_V4L2_COMMON=y
-CONFIG_VIDEO_ALLOW_V4L1=y
-CONFIG_VIDEO_V4L1_COMPAT=y
-# CONFIG_DVB_CORE is not set
-CONFIG_VIDEO_MEDIA=y
-
-#
-# Multimedia drivers
-#
-# CONFIG_MEDIA_ATTACH is not set
-CONFIG_MEDIA_TUNER=y
-# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
-CONFIG_MEDIA_TUNER_SIMPLE=y
-CONFIG_MEDIA_TUNER_TDA8290=y
-CONFIG_MEDIA_TUNER_TDA9887=y
-CONFIG_MEDIA_TUNER_TEA5761=y
-CONFIG_MEDIA_TUNER_TEA5767=y
-CONFIG_MEDIA_TUNER_MT20XX=y
-CONFIG_MEDIA_TUNER_XC2028=y
-CONFIG_MEDIA_TUNER_XC5000=y
-CONFIG_MEDIA_TUNER_MC44S803=y
-CONFIG_VIDEO_V4L2=y
-CONFIG_VIDEO_V4L1=y
-CONFIG_VIDEO_CAPTURE_DRIVERS=y
-# CONFIG_VIDEO_ADV_DEBUG is not set
-# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
-CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
-# CONFIG_VIDEO_VIVI is not set
-# CONFIG_VIDEO_CPIA is not set
-# CONFIG_VIDEO_SAA5246A is not set
-# CONFIG_VIDEO_SAA5249 is not set
-# CONFIG_SOC_CAMERA is not set
-# CONFIG_RADIO_ADAPTERS is not set
-# CONFIG_DAB is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -917,6 +931,7 @@ CONFIG_RTC_DRV_PCF8563=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -962,12 +977,15 @@ CONFIG_RTC_DRV_PCF8563=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 # CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
 # CONFIG_QUOTA is not set
 # CONFIG_AUTOFS_FS is not set
 # CONFIG_AUTOFS4_FS is not set
@@ -1021,6 +1039,12 @@ CONFIG_JFFS2_ZLIB=y
 # CONFIG_JFFS2_LZO is not set
 CONFIG_JFFS2_RTIME=y
 # CONFIG_JFFS2_RUBIN is not set
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_XATTR is not set
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+# CONFIG_UBIFS_FS_DEBUG is not set
 # CONFIG_CRAMFS is not set
 # CONFIG_SQUASHFS is not set
 # CONFIG_VXFS_FS is not set
@@ -1119,25 +1143,11 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y
 CONFIG_NOP_TRACER=y
 CONFIG_HAVE_FUNCTION_TRACER=y
 CONFIG_RING_BUFFER=y
+CONFIG_EVENT_TRACING=y
+CONFIG_CONTEXT_SWITCH_TRACER=y
 CONFIG_TRACING=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_IRQSOFF_TRACER is not set
-# CONFIG_PREEMPT_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_FTRACE_STARTUP_TEST is not set
+# CONFIG_FTRACE is not set
 # CONFIG_DYNAMIC_DEBUG is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
@@ -1151,16 +1161,104 @@ CONFIG_ARM_UNWIND=y
 # CONFIG_SECURITY is not set
 # CONFIG_SECURITYFS is not set
 # CONFIG_SECURITY_FILE_CAPABILITIES is not set
-# CONFIG_CRYPTO is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+CONFIG_CRYPTO_DEFLATE=y
+# CONFIG_CRYPTO_ZLIB is not set
+CONFIG_CRYPTO_LZO=y
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_HW=y
 CONFIG_BINARY_PRINTF=y
 
 #
 # Library routines
 #
 CONFIG_BITREVERSE=y
+CONFIG_RATIONAL=y
 CONFIG_GENERIC_FIND_LAST_BIT=y
 # CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
+CONFIG_CRC16=y
 # CONFIG_CRC_T10DIF is not set
 # CONFIG_CRC_ITU_T is not set
 CONFIG_CRC32=y
@@ -1168,6 +1266,8 @@ CONFIG_CRC32=y
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=y
 CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
-- 
GitLab


From 42469ff014812880d7324285d165841f4b1814e7 Mon Sep 17 00:00:00 2001
From: Sascha Hauer <s.hauer@pengutronix.de>
Date: Fri, 24 Jul 2009 17:31:03 +0200
Subject: [PATCH 0140/1153] mx3 defconfig update

- enable PCM043, MX31LILLY, ARMADILLO5X0 and MX35_3DS boards
- enable MXC nand driver
- enable UBI support
- disable cs89x0 support which broke all boards which do not have this chip

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/configs/mx3_defconfig | 151 ++++++++++++++++++++++-----------
 1 file changed, 102 insertions(+), 49 deletions(-)

diff --git a/arch/arm/configs/mx3_defconfig b/arch/arm/configs/mx3_defconfig
index 20ada526f6d..a4f9a2a8149 100644
--- a/arch/arm/configs/mx3_defconfig
+++ b/arch/arm/configs/mx3_defconfig
@@ -1,15 +1,15 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc1
-# Wed Apr  8 11:06:37 2009
+# Linux kernel version: 2.6.31-rc4
+# Tue Jul 28 14:11:34 2009
 #
 CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
 CONFIG_SYS_SUPPORTS_APM_EMULATION=y
 CONFIG_GENERIC_GPIO=y
 CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
 CONFIG_GENERIC_HARDIRQS=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
@@ -18,14 +18,13 @@ CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_HARDIRQS_SW_RESEND=y
 CONFIG_GENERIC_IRQ_PROBE=y
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
 CONFIG_GENERIC_HWEIGHT=y
 CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_ARCH_MTD_XIP=y
 CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 CONFIG_VECTORS_BASE=0xffff0000
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -86,7 +85,12 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+
+#
+# Performance Counters
+#
 CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -97,6 +101,11 @@ CONFIG_HAVE_OPROFILE=y
 # CONFIG_KPROBES is not set
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 CONFIG_HAVE_GENERIC_DMA_COHERENT=y
 CONFIG_SLABINFO=y
@@ -109,7 +118,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -136,13 +145,14 @@ CONFIG_FREEZER=y
 # CONFIG_ARCH_VERSATILE is not set
 # CONFIG_ARCH_AT91 is not set
 # CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
 # CONFIG_ARCH_EBSA110 is not set
 # CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_GEMINI is not set
 # CONFIG_ARCH_FOOTBRIDGE is not set
+CONFIG_ARCH_MXC=y
+# CONFIG_ARCH_STMP3XXX is not set
 # CONFIG_ARCH_NETX is not set
 # CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
 # CONFIG_ARCH_IOP13XX is not set
 # CONFIG_ARCH_IOP32X is not set
 # CONFIG_ARCH_IOP33X is not set
@@ -151,25 +161,25 @@ CONFIG_FREEZER=y
 # CONFIG_ARCH_IXP4XX is not set
 # CONFIG_ARCH_L7200 is not set
 # CONFIG_ARCH_KIRKWOOD is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
 # CONFIG_ARCH_LOKI is not set
 # CONFIG_ARCH_MV78XX0 is not set
-CONFIG_ARCH_MXC=y
 # CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
 # CONFIG_ARCH_PNX4008 is not set
 # CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_MSM is not set
 # CONFIG_ARCH_RPC is not set
 # CONFIG_ARCH_SA1100 is not set
 # CONFIG_ARCH_S3C2410 is not set
 # CONFIG_ARCH_S3C64XX is not set
 # CONFIG_ARCH_SHARK is not set
 # CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
 # CONFIG_ARCH_DAVINCI is not set
 # CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM is not set
-# CONFIG_ARCH_W90X900 is not set
 
 #
 # Freescale MXC Implementations
@@ -178,6 +188,7 @@ CONFIG_ARCH_MXC=y
 # CONFIG_ARCH_MX2 is not set
 CONFIG_ARCH_MX3=y
 CONFIG_ARCH_MX31=y
+CONFIG_ARCH_MX35=y
 
 #
 # MX3 platforms:
@@ -185,12 +196,19 @@ CONFIG_ARCH_MX31=y
 CONFIG_MACH_MX31ADS=y
 CONFIG_MACH_MX31ADS_WM1133_EV1=y
 CONFIG_MACH_PCM037=y
+CONFIG_MACH_PCM037_EET=y
 CONFIG_MACH_MX31LITE=y
 CONFIG_MACH_MX31_3DS=y
 CONFIG_MACH_MX31MOBOARD=y
+CONFIG_MACH_MX31LILLY=y
 CONFIG_MACH_QONG=y
+CONFIG_MACH_PCM043=y
+CONFIG_MACH_ARMADILLO5X0=y
+CONFIG_MACH_MX35_3DS=y
 CONFIG_MXC_IRQ_PRIOR=y
 CONFIG_MXC_PWM=y
+CONFIG_ARCH_HAS_RNGA=y
+CONFIG_ARCH_MXC_IOMUX_V3=y
 
 #
 # Processor Type
@@ -218,6 +236,7 @@ CONFIG_ARM_THUMB=y
 # CONFIG_CPU_BPREDICT_DISABLE is not set
 CONFIG_OUTER_CACHE=y
 CONFIG_CACHE_L2X0=y
+# CONFIG_ARM_ERRATA_411920 is not set
 CONFIG_COMMON_CLKDEV=y
 
 #
@@ -242,7 +261,6 @@ CONFIG_PREEMPT=y
 CONFIG_HZ=100
 CONFIG_AEABI=y
 CONFIG_OABI_COMPAT=y
-CONFIG_ARCH_FLATMEM_HAS_HOLES=y
 # CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
 # CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
 # CONFIG_HIGHMEM is not set
@@ -257,10 +275,11 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 # CONFIG_PHYS_ADDR_T_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
 
 #
 # Boot options
@@ -362,6 +381,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -465,7 +485,16 @@ CONFIG_MTD_PHYSMAP=y
 # CONFIG_MTD_DOC2000 is not set
 # CONFIG_MTD_DOC2001 is not set
 # CONFIG_MTD_DOC2001PLUS is not set
-# CONFIG_MTD_NAND is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+CONFIG_MTD_NAND_MXC=y
 # CONFIG_MTD_ONENAND is not set
 
 #
@@ -476,10 +505,30 @@ CONFIG_MTD_PHYSMAP=y
 #
 # UBI - Unsorted block images
 #
-# CONFIG_MTD_UBI is not set
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MTD_UBI_BEB_RESERVE=1
+# CONFIG_MTD_UBI_GLUEBI is not set
+
+#
+# UBI debugging options
+#
+# CONFIG_MTD_UBI_DEBUG is not set
 # CONFIG_PARPORT is not set
 # CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+CONFIG_EEPROM_AT24=y
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+# CONFIG_EEPROM_93CX6 is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -493,7 +542,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_ATA is not set
 # CONFIG_MD is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -528,7 +576,7 @@ CONFIG_MII=y
 # CONFIG_ETHOC is not set
 # CONFIG_SMC911X is not set
 CONFIG_SMSC911X=y
-# CONFIG_DNET is not set
+CONFIG_DNET=y
 # CONFIG_IBM_NEW_EMAC_ZMII is not set
 # CONFIG_IBM_NEW_EMAC_RGMII is not set
 # CONFIG_IBM_NEW_EMAC_TAH is not set
@@ -537,8 +585,10 @@ CONFIG_SMSC911X=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
-CONFIG_CS89x0=y
-CONFIG_CS89x0_NONISA_IRQ=y
+# CONFIG_CS89x0 is not set
+# CONFIG_KS8842 is not set
+CONFIG_FEC=y
+# CONFIG_FEC2 is not set
 # CONFIG_NETDEV_1000 is not set
 # CONFIG_NETDEV_10000 is not set
 
@@ -609,6 +659,7 @@ CONFIG_I2C_HELPER_AUTO=y
 #
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_GPIO is not set
 CONFIG_I2C_IMX=y
 # CONFIG_I2C_OCORES is not set
@@ -633,7 +684,6 @@ CONFIG_I2C_IMX=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -669,6 +719,7 @@ CONFIG_W1=y
 #
 # CONFIG_W1_MASTER_DS2482 is not set
 CONFIG_W1_MASTER_MXC=y
+# CONFIG_W1_MASTER_DS1WM is not set
 # CONFIG_W1_MASTER_GPIO is not set
 
 #
@@ -703,6 +754,8 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_TPS65010 is not set
 # CONFIG_TWL4030_CORE is not set
 # CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
 # CONFIG_MFD_TC6393XB is not set
 # CONFIG_PMIC_DA903X is not set
 # CONFIG_MFD_WM8400 is not set
@@ -711,10 +764,8 @@ CONFIG_MFD_WM8350_CONFIG_MODE_0=y
 CONFIG_MFD_WM8352_CONFIG_MODE_0=y
 CONFIG_MFD_WM8350_I2C=y
 # CONFIG_MFD_PCF50633 is not set
-
-#
-# Multimedia devices
-#
+# CONFIG_AB3100_CORE is not set
+CONFIG_MEDIA_SUPPORT=y
 
 #
 # Multimedia core support
@@ -758,8 +809,10 @@ CONFIG_SOC_CAMERA_MT9T031=y
 CONFIG_SOC_CAMERA_MT9V022=y
 CONFIG_SOC_CAMERA_TW9910=y
 # CONFIG_SOC_CAMERA_PLATFORM is not set
-# CONFIG_SOC_CAMERA_OV772X is not set
+CONFIG_SOC_CAMERA_OV772X=y
+CONFIG_MX3_VIDEO=y
 CONFIG_VIDEO_MX3=y
+# CONFIG_VIDEO_SH_MOBILE_CEU is not set
 # CONFIG_RADIO_ADAPTERS is not set
 # CONFIG_DAB is not set
 
@@ -847,8 +900,11 @@ CONFIG_REGULATOR=y
 # CONFIG_REGULATOR_DEBUG is not set
 # CONFIG_REGULATOR_FIXED_VOLTAGE is not set
 # CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
 # CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
 CONFIG_REGULATOR_WM8350=y
+# CONFIG_REGULATOR_LP3971 is not set
 # CONFIG_UIO is not set
 # CONFIG_STAGING is not set
 
@@ -861,10 +917,12 @@ CONFIG_REGULATOR_WM8350=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -921,6 +979,12 @@ CONFIG_JFFS2_ZLIB=y
 # CONFIG_JFFS2_LZO is not set
 CONFIG_JFFS2_RTIME=y
 # CONFIG_JFFS2_RUBIN is not set
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_XATTR is not set
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+# CONFIG_UBIFS_FS_DEBUG is not set
 # CONFIG_CRAMFS is not set
 # CONFIG_SQUASHFS is not set
 # CONFIG_VXFS_FS is not set
@@ -937,6 +1001,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -979,22 +1044,7 @@ CONFIG_FRAME_WARN=1024
 CONFIG_SYSCTL_SYSCALL_CHECK=y
 CONFIG_HAVE_FUNCTION_TRACER=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_IRQSOFF_TRACER is not set
-# CONFIG_PREEMPT_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 CONFIG_ARM_UNWIND=y
@@ -1094,9 +1144,9 @@ CONFIG_CRYPTO_DES=y
 #
 # Compression
 #
-# CONFIG_CRYPTO_DEFLATE is not set
+CONFIG_CRYPTO_DEFLATE=y
 # CONFIG_CRYPTO_ZLIB is not set
-# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_LZO=y
 
 #
 # Random Number Generation
@@ -1109,9 +1159,10 @@ CONFIG_CRYPTO_HW=y
 # Library routines
 #
 CONFIG_BITREVERSE=y
+CONFIG_RATIONAL=y
 CONFIG_GENERIC_FIND_LAST_BIT=y
 # CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
+CONFIG_CRC16=y
 # CONFIG_CRC_T10DIF is not set
 # CONFIG_CRC_ITU_T is not set
 CONFIG_CRC32=y
@@ -1119,6 +1170,8 @@ CONFIG_CRC32=y
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=y
 CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
-- 
GitLab


From f25784b35f590c81d5fb8245a8cd45e1afb6f1b2 Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Tue, 28 Jul 2009 08:41:57 -0400
Subject: [PATCH 0141/1153] Btrfs: Fix async caching interaction with unmount

- don't stop the caching thread until btrfs_commit_super return.

- if caching is interrupted by umount, set last to (u64)-1.
  otherwise the un-scanned range of block group will be considered
  as free extent.

Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/disk-io.c     | 3 +++
 fs/btrfs/extent-tree.c | 4 +++-
 2 files changed, 6 insertions(+), 1 deletion(-)

diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c
index c658397c747..3a9b8875988 100644
--- a/fs/btrfs/disk-io.c
+++ b/fs/btrfs/disk-io.c
@@ -2317,6 +2317,9 @@ int close_ctree(struct btrfs_root *root)
 			printk(KERN_ERR "btrfs: commit super ret %d\n", ret);
 	}
 
+	fs_info->closing = 2;
+	smp_mb();
+
 	if (fs_info->delalloc_bytes) {
 		printk(KERN_INFO "btrfs: at unmount delalloc count %llu\n",
 		       (unsigned long long)fs_info->delalloc_bytes);
diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index 08188f1615d..fadf69a2764 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -288,8 +288,10 @@ again:
 
 	while (1) {
 		smp_mb();
-		if (block_group->fs_info->closing)
+		if (block_group->fs_info->closing > 1) {
+			last = (u64)-1;
 			break;
+		}
 
 		leaf = path->nodes[0];
 		slot = path->slots[0];
-- 
GitLab


From 1b54ab450b180eaeeb0eee6f0f64349246a22c14 Mon Sep 17 00:00:00 2001
From: Jean Delvare <khali@linux-fr.org>
Date: Tue, 28 Jul 2009 16:31:39 +0200
Subject: [PATCH 0142/1153] hwmon: (smsc47m1) Differentiate between LPC47M233
 and LPC47M292

The SMSC LPC47M233 and LPC47M292 chips have the same device ID but
are not compatible.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
---
 drivers/hwmon/smsc47m1.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/hwmon/smsc47m1.c b/drivers/hwmon/smsc47m1.c
index a92dbb97ee9..ba75bfcf14c 100644
--- a/drivers/hwmon/smsc47m1.c
+++ b/drivers/hwmon/smsc47m1.c
@@ -86,6 +86,7 @@ superio_exit(void)
 #define SUPERIO_REG_ACT		0x30
 #define SUPERIO_REG_BASE	0x60
 #define SUPERIO_REG_DEVID	0x20
+#define SUPERIO_REG_DEVREV	0x21
 
 /* Logical device registers */
 
@@ -429,6 +430,9 @@ static int __init smsc47m1_find(unsigned short *addr,
 	 * The LPC47M292 (device id 0x6B) is somewhat compatible, but it
 	 * supports a 3rd fan, and the pin configuration registers are
 	 * unfortunately different.
+	 * The LPC47M233 has the same device id (0x6B) but is not compatible.
+	 * We check the high bit of the device revision register to
+	 * differentiate them.
 	 */
 	switch (val) {
 	case 0x51:
@@ -448,6 +452,13 @@ static int __init smsc47m1_find(unsigned short *addr,
 		sio_data->type = smsc47m1;
 		break;
 	case 0x6B:
+		if (superio_inb(SUPERIO_REG_DEVREV) & 0x80) {
+			pr_debug(DRVNAME ": "
+				 "Found SMSC LPC47M233, unsupported\n");
+			superio_exit();
+			return -ENODEV;
+		}
+
 		pr_info(DRVNAME ": Found SMSC LPC47M292\n");
 		sio_data->type = smsc47m2;
 		break;
-- 
GitLab


From 8d282497cbf8124d6814d51a74fb13d69531c669 Mon Sep 17 00:00:00 2001
From: Luca Tettamanti <kronos.it@gmail.com>
Date: Tue, 28 Jul 2009 16:31:39 +0200
Subject: [PATCH 0143/1153] hwmon: (asus_atk0110) Fix upper limit readings

On newer Asus boards the "upper" limit of a sensor is encoded as
delta from the "lower" limit. Fix the driver to correctly handle
this case.

Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Alex Macfarlane Smith <nospam@archifishal.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
---
 drivers/hwmon/asus_atk0110.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/hwmon/asus_atk0110.c b/drivers/hwmon/asus_atk0110.c
index bff0103610c..fe4fa29c921 100644
--- a/drivers/hwmon/asus_atk0110.c
+++ b/drivers/hwmon/asus_atk0110.c
@@ -593,7 +593,11 @@ static int atk_add_sensor(struct atk_data *data, union acpi_object *obj)
 	sensor->data = data;
 	sensor->id = flags->integer.value;
 	sensor->limit1 = limit1->integer.value;
-	sensor->limit2 = limit2->integer.value;
+	if (data->old_interface)
+		sensor->limit2 = limit2->integer.value;
+	else
+		/* The upper limit is expressed as delta from lower limit */
+		sensor->limit2 = sensor->limit1 + limit2->integer.value;
 
 	snprintf(sensor->input_attr_name, ATTR_NAME_SIZE,
 			"%s%d_input", base_name, start + *num);
-- 
GitLab


From 96f699ad09c8b3c55cd229506a9add0047838e3e Mon Sep 17 00:00:00 2001
From: Michele Jr De Candia <michele.decandia@valueteam.com>
Date: Tue, 28 Jul 2009 16:33:03 +0200
Subject: [PATCH 0144/1153] i2c/tsl2550: Fix lux value in dark environment

I've tested TSL2550 driver and I've found a bug: when light is off,
returned value from tsl2550_calculate_lux function is -1 when it should
be 0 (sensor correctly read that light was off).

I think the bug is that a zero c0 value (approximated value of ch0) is
misinterpreted as an error.

Signed-off-by: Michele Jr De Candia <michele.decandia@valueteam.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
---
 drivers/i2c/chips/tsl2550.c | 17 ++++++++++-------
 1 file changed, 10 insertions(+), 7 deletions(-)

diff --git a/drivers/i2c/chips/tsl2550.c b/drivers/i2c/chips/tsl2550.c
index 1a9cc135219..b96f3025e58 100644
--- a/drivers/i2c/chips/tsl2550.c
+++ b/drivers/i2c/chips/tsl2550.c
@@ -27,7 +27,7 @@
 #include <linux/delay.h>
 
 #define TSL2550_DRV_NAME	"tsl2550"
-#define DRIVER_VERSION		"1.1.1"
+#define DRIVER_VERSION		"1.1.2"
 
 /*
  * Defines
@@ -189,13 +189,16 @@ static int tsl2550_calculate_lux(u8 ch0, u8 ch1)
 	u8 r = 128;
 
 	/* Avoid division by 0 and count 1 cannot be greater than count 0 */
-	if (c0 && (c1 <= c0))
-		r = c1 * 128 / c0;
+	if (c1 <= c0)
+		if (c0) {
+			r = c1 * 128 / c0;
+
+			/* Calculate LUX */
+			lux = ((c0 - c1) * ratio_lut[r]) / 256;
+		} else
+			lux = 0;
 	else
-		return -1;
-
-	/* Calculate LUX */
-	lux = ((c0 - c1) * ratio_lut[r]) / 256;
+		return -EAGAIN;
 
 	/* LUX range check */
 	return lux > TSL2550_MAX_LUX ? TSL2550_MAX_LUX : lux;
-- 
GitLab


From 56ad1740d9a8dc271e71fee234be662638c64458 Mon Sep 17 00:00:00 2001
From: Jens Axboe <jens.axboe@oracle.com>
Date: Tue, 28 Jul 2009 22:11:24 +0200
Subject: [PATCH 0145/1153] block: make the end_io functions be non-GPL exports

Prior to the change for more sane end_io functions, we exported
the helpers with the normal EXPORT_SYMBOL(). That got changed
to _GPL() for the new interface. Revert that particular change,
on the basis that this is basic functionality and doesn't dip
into internal structures. If these exports can't be non-GPL,
then we may as well make EXPORT_SYMBOL() imply GPL for
everything.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 block/blk-core.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/block/blk-core.c b/block/blk-core.c
index a0c340d239b..e3299a77a0d 100644
--- a/block/blk-core.c
+++ b/block/blk-core.c
@@ -2136,7 +2136,7 @@ bool blk_end_request(struct request *rq, int error, unsigned int nr_bytes)
 {
 	return blk_end_bidi_request(rq, error, nr_bytes, 0);
 }
-EXPORT_SYMBOL_GPL(blk_end_request);
+EXPORT_SYMBOL(blk_end_request);
 
 /**
  * blk_end_request_all - Helper function for drives to finish the request.
@@ -2157,7 +2157,7 @@ void blk_end_request_all(struct request *rq, int error)
 	pending = blk_end_bidi_request(rq, error, blk_rq_bytes(rq), bidi_bytes);
 	BUG_ON(pending);
 }
-EXPORT_SYMBOL_GPL(blk_end_request_all);
+EXPORT_SYMBOL(blk_end_request_all);
 
 /**
  * blk_end_request_cur - Helper function to finish the current request chunk.
@@ -2175,7 +2175,7 @@ bool blk_end_request_cur(struct request *rq, int error)
 {
 	return blk_end_request(rq, error, blk_rq_cur_bytes(rq));
 }
-EXPORT_SYMBOL_GPL(blk_end_request_cur);
+EXPORT_SYMBOL(blk_end_request_cur);
 
 /**
  * __blk_end_request - Helper function for drivers to complete the request.
@@ -2194,7 +2194,7 @@ bool __blk_end_request(struct request *rq, int error, unsigned int nr_bytes)
 {
 	return __blk_end_bidi_request(rq, error, nr_bytes, 0);
 }
-EXPORT_SYMBOL_GPL(__blk_end_request);
+EXPORT_SYMBOL(__blk_end_request);
 
 /**
  * __blk_end_request_all - Helper function for drives to finish the request.
@@ -2215,7 +2215,7 @@ void __blk_end_request_all(struct request *rq, int error)
 	pending = __blk_end_bidi_request(rq, error, blk_rq_bytes(rq), bidi_bytes);
 	BUG_ON(pending);
 }
-EXPORT_SYMBOL_GPL(__blk_end_request_all);
+EXPORT_SYMBOL(__blk_end_request_all);
 
 /**
  * __blk_end_request_cur - Helper function to finish the current request chunk.
@@ -2234,7 +2234,7 @@ bool __blk_end_request_cur(struct request *rq, int error)
 {
 	return __blk_end_request(rq, error, blk_rq_cur_bytes(rq));
 }
-EXPORT_SYMBOL_GPL(__blk_end_request_cur);
+EXPORT_SYMBOL(__blk_end_request_cur);
 
 void blk_rq_bio_prep(struct request_queue *q, struct request *rq,
 		     struct bio *bio)
-- 
GitLab


From 0f58b44582001c8bcdb75f36cf85ebbe5170e959 Mon Sep 17 00:00:00 2001
From: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Date: Tue, 14 Jul 2009 17:56:15 +0200
Subject: [PATCH 0146/1153] sysfs: fix hardlink count on device_move

Update directory hardlink count when moving kobjects to a new parent.
Fixes the following problem which occurs when several devices are
moved to the same parent and then unregistered:

> ls -laF /sys/devices/css0/defunct/
> total 0
> drwxr-xr-x 4294967295 root root    0 2009-07-14 17:02 ./
> drwxr-xr-x        114 root root    0 2009-07-14 17:02 ../
> drwxr-xr-x          2 root root    0 2009-07-14 17:01 power/
> -rw-r--r--          1 root root 4096 2009-07-14 17:01 uevent

Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 fs/sysfs/dir.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/fs/sysfs/dir.c b/fs/sysfs/dir.c
index d88d0fac9fa..14f2d71ea3c 100644
--- a/fs/sysfs/dir.c
+++ b/fs/sysfs/dir.c
@@ -939,8 +939,10 @@ again:
 	/* Remove from old parent's list and insert into new parent's list. */
 	sysfs_unlink_sibling(sd);
 	sysfs_get(new_parent_sd);
+	drop_nlink(old_parent->d_inode);
 	sysfs_put(sd->s_parent);
 	sd->s_parent = new_parent_sd;
+	inc_nlink(new_parent->d_inode);
 	sysfs_link_sibling(sd);
 
  out_unlock:
-- 
GitLab


From 3b4418c67a70278964b063b5e1f56dcb3d0a41f3 Mon Sep 17 00:00:00 2001
From: Ming Lei <tom.leiming@gmail.com>
Date: Sat, 11 Jul 2009 11:11:10 +0800
Subject: [PATCH 0147/1153] driver core: firmware_class:fix memory leak of page
 pointers array

The page pointers array is allocated in fw_realloc_buffer() called by
firmware_data_write(), and should be freed in release function of firmware
device.

Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/base/firmware_class.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/base/firmware_class.c b/drivers/base/firmware_class.c
index f285f441fab..7376367bcb8 100644
--- a/drivers/base/firmware_class.c
+++ b/drivers/base/firmware_class.c
@@ -180,7 +180,6 @@ static ssize_t firmware_loading_store(struct device *dev,
 				goto err;
 			}
 			/* Pages will be freed by vfree() */
-			fw_priv->pages = NULL;
 			fw_priv->page_array_size = 0;
 			fw_priv->nr_pages = 0;
 			complete(&fw_priv->completion);
-- 
GitLab


From 4df7b3e0370ab6161ea2f258f51dd7c43bef2bda Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Wed, 15 Jul 2009 20:29:07 +0200
Subject: [PATCH 0148/1153] Dynamic debug: fix typo: -/->

The member was intended, not the local variable.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Greg Banks <gnb@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 lib/dynamic_debug.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/lib/dynamic_debug.c b/lib/dynamic_debug.c
index 833139ce1e2..e22c148e4b7 100644
--- a/lib/dynamic_debug.c
+++ b/lib/dynamic_debug.c
@@ -164,7 +164,7 @@ static void ddebug_change(const struct ddebug_query *query,
 
 			if (!newflags)
 				dt->num_enabled--;
-			else if (!dp-flags)
+			else if (!dp->flags)
 				dt->num_enabled++;
 			dp->flags = newflags;
 			if (newflags) {
-- 
GitLab


From 79f0313bfc67aa13abb931e8c12a1411f0161a68 Mon Sep 17 00:00:00 2001
From: Xiaotian Feng <dfeng@redhat.com>
Date: Fri, 24 Jul 2009 17:31:41 +0800
Subject: [PATCH 0149/1153] driver core: sysdev: do not send KOBJ_ADD uevent if
 kobject_init_and_add fails

If kobject_init_and_add fails, sysdev_register should not send KOBJ_ADD
uevent to userspace.

Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/base/sys.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/base/sys.c b/drivers/base/sys.c
index 79a9ae5238a..0d903909af7 100644
--- a/drivers/base/sys.c
+++ b/drivers/base/sys.c
@@ -275,9 +275,9 @@ int sysdev_register(struct sys_device *sysdev)
 				drv->add(sysdev);
 		}
 		mutex_unlock(&sysdev_drivers_lock);
+		kobject_uevent(&sysdev->kobj, KOBJ_ADD);
 	}
 
-	kobject_uevent(&sysdev->kobj, KOBJ_ADD);
 	return error;
 }
 
-- 
GitLab


From a39ea210ec8c8f6ed381f8dafbe755c57b8f30c3 Mon Sep 17 00:00:00 2001
From: Lucian Adrian Grijincu <lgrijincu@ixiacom.com>
Date: Mon, 27 Jul 2009 09:06:42 -0700
Subject: [PATCH 0150/1153] driver core: documentation: make it clear that
 sysfs is optional

The original text suggested that sysfs is mandatory and always
compiled in the kernel.

Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 Documentation/filesystems/sysfs.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/filesystems/sysfs.txt b/Documentation/filesystems/sysfs.txt
index 7e81e37c0b1..b245d524d56 100644
--- a/Documentation/filesystems/sysfs.txt
+++ b/Documentation/filesystems/sysfs.txt
@@ -23,7 +23,8 @@ interface.
 Using sysfs
 ~~~~~~~~~~~
 
-sysfs is always compiled in. You can access it by doing:
+sysfs is always compiled in if CONFIG_SYSFS is defined. You can access
+it by doing:
 
     mount -t sysfs sysfs /sys 
 
-- 
GitLab


From f3a756883ac028c536479e2eb283477fec80c828 Mon Sep 17 00:00:00 2001
From: Bill Pemberton <wfp5p@virginia.edu>
Date: Tue, 14 Jul 2009 15:33:52 -0400
Subject: [PATCH 0151/1153] Staging: serqt_usb2: add missing calls to
 tty_kref_put()

tty_port_tty_get() was called without a corresponding tty_kref_put()
in qt_read_bulk_callback() and qt_close().

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/staging/serqt_usb2/serqt_usb2.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/drivers/staging/serqt_usb2/serqt_usb2.c b/drivers/staging/serqt_usb2/serqt_usb2.c
index a9bd4106beb..f9ff9c26678 100644
--- a/drivers/staging/serqt_usb2/serqt_usb2.c
+++ b/drivers/staging/serqt_usb2/serqt_usb2.c
@@ -360,18 +360,18 @@ static void qt_read_bulk_callback(struct urb *urb)
 	if (port_paranoia_check(port, __func__) != 0) {
 		dbg("%s - port_paranoia_check, exiting\n", __func__);
 		qt_port->ReadBulkStopped = 1;
-		return;
+		goto exit;
 	}
 
 	if (!serial) {
 		dbg("%s - bad serial pointer, exiting\n", __func__);
-		return;
+		goto exit;
 	}
 	if (qt_port->closePending == 1) {
 		/* Were closing , stop reading */
 		dbg("%s - (qt_port->closepending == 1\n", __func__);
 		qt_port->ReadBulkStopped = 1;
-		return;
+		goto exit;
 	}
 
 	/*
@@ -381,7 +381,7 @@ static void qt_read_bulk_callback(struct urb *urb)
 	 */
 	if (qt_port->RxHolding == 1) {
 		qt_port->ReadBulkStopped = 1;
-		return;
+		goto exit;
 	}
 
 	if (urb->status) {
@@ -389,7 +389,7 @@ static void qt_read_bulk_callback(struct urb *urb)
 
 		dbg("%s - nonzero read bulk status received: %d\n",
 		    __func__, urb->status);
-		return;
+		goto exit;
 	}
 
 	if (tty && RxCount) {
@@ -463,6 +463,8 @@ static void qt_read_bulk_callback(struct urb *urb)
 	}
 
 	schedule_work(&port->work);
+exit:
+	tty_kref_put(tty);
 }
 
 /*
@@ -1041,7 +1043,7 @@ static void qt_block_until_empty(struct tty_struct *tty,
 	}
 }
 
-static void qt_close( struct usb_serial_port *port)
+static void qt_close(struct usb_serial_port *port)
 {
 	struct usb_serial *serial = port->serial;
 	struct quatech_port *qt_port;
@@ -1068,6 +1070,7 @@ static void qt_close( struct usb_serial_port *port)
 	/* wait up to for transmitter to empty */
 	if (serial->dev)
 		qt_block_until_empty(tty, qt_port);
+	tty_kref_put(tty);
 
 	/* Close uart channel */
 	status = qt_close_channel(serial, index);
-- 
GitLab


From de8f8bd63334fe2014be7d9ab3a81ce9b96e5d19 Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Mon, 13 Jul 2009 10:46:57 +0200
Subject: [PATCH 0152/1153] Staging: serqt_usb2: fix memory leak in error case

a standard memory leak, as later allocations may fail even if prior
allocations did not. Then the prior allocations must be undone.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/staging/serqt_usb2/serqt_usb2.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/staging/serqt_usb2/serqt_usb2.c b/drivers/staging/serqt_usb2/serqt_usb2.c
index f9ff9c26678..0fdf8c6dc64 100644
--- a/drivers/staging/serqt_usb2/serqt_usb2.c
+++ b/drivers/staging/serqt_usb2/serqt_usb2.c
@@ -738,6 +738,11 @@ static int qt_startup(struct usb_serial *serial)
 		if (!qt_port) {
 			dbg("%s: kmalloc for quatech_port (%d) failed!.",
 			    __func__, i);
+			for(--i; i >= 0; i--) {
+				port = serial->port[i];
+				kfree(usb_get_serial_port_data(port));
+				usb_set_serial_port_data(port, NULL);
+			}
 			return -ENOMEM;
 		}
 		spin_lock_init(&qt_port->lock);
-- 
GitLab


From a6a9f81ccc9f5c86ccc22bbed1960a57d0316e8b Mon Sep 17 00:00:00 2001
From: David Rientjes <rientjes@google.com>
Date: Tue, 16 Jun 2009 16:42:53 -0700
Subject: [PATCH 0153/1153] Staging: android: lowmemorykiller.c: fix it for
 "oom: move oom_adj value from task_struct to mm_struct"

I'm about to merge "oom: move oom_adj value from task_struct to
mm_struct", and this fixup is needed to repair linux-next's
drivers/staging/android/lowmemorykiller.c.

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/staging/android/lowmemorykiller.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/staging/android/lowmemorykiller.c b/drivers/staging/android/lowmemorykiller.c
index fe72240f5a9..f934393f395 100644
--- a/drivers/staging/android/lowmemorykiller.c
+++ b/drivers/staging/android/lowmemorykiller.c
@@ -96,19 +96,21 @@ static int lowmem_shrink(int nr_to_scan, gfp_t gfp_mask)
 
 	read_lock(&tasklist_lock);
 	for_each_process(p) {
+		struct mm_struct *mm;
 		int oom_adj;
 
 		task_lock(p);
-		if (!p->mm) {
+		mm = p->mm;
+		if (!mm) {
 			task_unlock(p);
 			continue;
 		}
-		oom_adj = p->oomkilladj;
+		oom_adj = mm->oom_adj;
 		if (oom_adj < min_adj) {
 			task_unlock(p);
 			continue;
 		}
-		tasksize = get_mm_rss(p->mm);
+		tasksize = get_mm_rss(mm);
 		task_unlock(p);
 		if (tasksize <= 0)
 			continue;
-- 
GitLab


From 0bfc240575acb8769d0be78facedabd8e3d2c33a Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Sun, 19 Jul 2009 23:37:32 -0700
Subject: [PATCH 0154/1153] staging: remove aten2011 driver

This driver is not needed, as the existing mos7840 driver works
properly for this device.

Thanks to Russell Lang for doing the work to figure this out.

Cc: Russell Lang <gsview@ghostgum.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/staging/Kconfig           |    2 -
 drivers/staging/Makefile          |    1 -
 drivers/staging/uc2322/Kconfig    |   10 -
 drivers/staging/uc2322/Makefile   |    1 -
 drivers/staging/uc2322/TODO       |    7 -
 drivers/staging/uc2322/aten2011.c | 2430 -----------------------------
 6 files changed, 2451 deletions(-)
 delete mode 100644 drivers/staging/uc2322/Kconfig
 delete mode 100644 drivers/staging/uc2322/Makefile
 delete mode 100644 drivers/staging/uc2322/TODO
 delete mode 100644 drivers/staging/uc2322/aten2011.c

diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
index 348bf61a8fe..975ecddbce3 100644
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -103,8 +103,6 @@ source "drivers/staging/pohmelfs/Kconfig"
 
 source "drivers/staging/stlc45xx/Kconfig"
 
-source "drivers/staging/uc2322/Kconfig"
-
 source "drivers/staging/b3dfg/Kconfig"
 
 source "drivers/staging/phison/Kconfig"
diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
index 8d61d7b4deb..2241ae1b21e 100644
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -34,7 +34,6 @@ obj-$(CONFIG_ANDROID)		+= android/
 obj-$(CONFIG_DST)		+= dst/
 obj-$(CONFIG_POHMELFS)		+= pohmelfs/
 obj-$(CONFIG_STLC45XX)		+= stlc45xx/
-obj-$(CONFIG_USB_SERIAL_ATEN2011)	+= uc2322/
 obj-$(CONFIG_B3DFG)		+= b3dfg/
 obj-$(CONFIG_IDE_PHISON)	+= phison/
 obj-$(CONFIG_PLAN9AUTH)		+= p9auth/
diff --git a/drivers/staging/uc2322/Kconfig b/drivers/staging/uc2322/Kconfig
deleted file mode 100644
index 2e0c6e79df2..00000000000
--- a/drivers/staging/uc2322/Kconfig
+++ /dev/null
@@ -1,10 +0,0 @@
-config USB_SERIAL_ATEN2011
-	tristate "ATEN 2011 USB to serial device support"
-	depends on USB_SERIAL
-	default N
-	---help---
-	  Say Y here if you want to use a ATEN 2011 dual port USB to serial
-	  adapter.
-
-	  To compile this driver as a module, choose M here: the module will be
-	  called aten2011.
diff --git a/drivers/staging/uc2322/Makefile b/drivers/staging/uc2322/Makefile
deleted file mode 100644
index 49c18d6e579..00000000000
--- a/drivers/staging/uc2322/Makefile
+++ /dev/null
@@ -1 +0,0 @@
-obj-$(CONFIG_USB_SERIAL_ATEN2011)	+= aten2011.o
diff --git a/drivers/staging/uc2322/TODO b/drivers/staging/uc2322/TODO
deleted file mode 100644
index c189a64c418..00000000000
--- a/drivers/staging/uc2322/TODO
+++ /dev/null
@@ -1,7 +0,0 @@
-TODO:
-	- checkpatch.pl cleanups
-	- remove dead and useless code (auditing the tty ioctls to
-	  verify that they really are correct and needed.)
-
-Please send any patches to Greg Kroah-Hartman <greg@kroah.com> and
-Russell Lang <gsview@ghostgum.com.au>.
diff --git a/drivers/staging/uc2322/aten2011.c b/drivers/staging/uc2322/aten2011.c
deleted file mode 100644
index 39d0926d1a9..00000000000
--- a/drivers/staging/uc2322/aten2011.c
+++ /dev/null
@@ -1,2430 +0,0 @@
-/*
- * Aten 2011 USB serial driver for 4 port devices
- *
- * Copyright (C) 2000 Inside Out Networks
- * Copyright (C) 2001-2002, 2009 Greg Kroah-Hartman <greg@kroah.com>
- * Copyright (C) 2009 Novell Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/tty.h>
-#include <linux/tty_driver.h>
-#include <linux/tty_flip.h>
-#include <linux/module.h>
-#include <linux/serial.h>
-#include <linux/uaccess.h>
-#include <linux/usb.h>
-#include <linux/usb/serial.h>
-
-
-#define ZLP_REG1		0x3A	/* Zero_Flag_Reg1 58 */
-#define ZLP_REG2		0x3B	/* Zero_Flag_Reg2 59 */
-#define ZLP_REG3		0x3C	/* Zero_Flag_Reg3 60 */
-#define ZLP_REG4		0x3D	/* Zero_Flag_Reg4 61 */
-#define ZLP_REG5		0x3E	/* Zero_Flag_Reg5 62 */
-
-/* Interrupt Rotinue Defines	*/
-#define SERIAL_IIR_RLS		0x06
-#define SERIAL_IIR_RDA		0x04
-#define SERIAL_IIR_CTI		0x0c
-#define SERIAL_IIR_THR		0x02
-#define SERIAL_IIR_MS		0x00
-
-/* Emulation of the bit mask on the LINE STATUS REGISTER.  */
-#define SERIAL_LSR_DR		0x0001
-#define SERIAL_LSR_OE		0x0002
-#define SERIAL_LSR_PE		0x0004
-#define SERIAL_LSR_FE		0x0008
-#define SERIAL_LSR_BI		0x0010
-#define SERIAL_LSR_THRE		0x0020
-#define SERIAL_LSR_TEMT		0x0040
-#define SERIAL_LSR_FIFOERR	0x0080
-
-/* MSR bit defines(place holders) */
-#define ATEN_MSR_DELTA_CTS	0x10
-#define ATEN_MSR_DELTA_DSR	0x20
-#define ATEN_MSR_DELTA_RI	0x40
-#define ATEN_MSR_DELTA_CD	0x80
-
-/* Serial Port register Address */
-#define RECEIVE_BUFFER_REGISTER		((__u16)(0x00))
-#define TRANSMIT_HOLDING_REGISTER	((__u16)(0x00))
-#define INTERRUPT_ENABLE_REGISTER	((__u16)(0x01))
-#define INTERRUPT_IDENT_REGISTER	((__u16)(0x02))
-#define FIFO_CONTROL_REGISTER		((__u16)(0x02))
-#define LINE_CONTROL_REGISTER		((__u16)(0x03))
-#define MODEM_CONTROL_REGISTER		((__u16)(0x04))
-#define LINE_STATUS_REGISTER		((__u16)(0x05))
-#define MODEM_STATUS_REGISTER		((__u16)(0x06))
-#define SCRATCH_PAD_REGISTER		((__u16)(0x07))
-#define DIVISOR_LATCH_LSB		((__u16)(0x00))
-#define DIVISOR_LATCH_MSB		((__u16)(0x01))
-
-#define SP1_REGISTER			((__u16)(0x00))
-#define CONTROL1_REGISTER		((__u16)(0x01))
-#define CLK_MULTI_REGISTER		((__u16)(0x02))
-#define CLK_START_VALUE_REGISTER	((__u16)(0x03))
-#define DCR1_REGISTER			((__u16)(0x04))
-#define GPIO_REGISTER			((__u16)(0x07))
-
-#define SERIAL_LCR_DLAB			((__u16)(0x0080))
-
-/*
- * URB POOL related defines
- */
-#define NUM_URBS			16	/* URB Count */
-#define URB_TRANSFER_BUFFER_SIZE	32	/* URB Size  */
-
-#define USB_VENDOR_ID_ATENINTL		0x0557
-#define ATENINTL_DEVICE_ID_2011		0x2011
-#define ATENINTL_DEVICE_ID_7820		0x7820
-
-static struct usb_device_id id_table[] = {
-	{ USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_2011) },
-	{ USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_7820) },
-	{ } /* terminating entry */
-};
-MODULE_DEVICE_TABLE(usb, id_table);
-
-/* This structure holds all of the local port information */
-struct ATENINTL_port {
-	int		port_num;          /*Actual port number in the device(1,2,etc)*/
-	__u8		bulk_out_endpoint;   	/* the bulk out endpoint handle */
-	unsigned char	*bulk_out_buffer;     	/* buffer used for the bulk out endpoint */
-	struct urb	*write_urb;	     	/* write URB for this port */
-	__u8		bulk_in_endpoint;	/* the bulk in endpoint handle */
-	unsigned char	*bulk_in_buffer;	/* the buffer we use for the bulk in endpoint */
-	struct urb	*read_urb;	     	/* read URB for this port */
-	__u8		shadowLCR;		/* last LCR value received */
-	__u8		shadowMCR;		/* last MCR value received */
-	char		open;
-	char		chaseResponsePending;
-	wait_queue_head_t	wait_chase;		/* for handling sleeping while waiting for chase to finish */
-	wait_queue_head_t	wait_command;		/* for handling sleeping while waiting for command to finish */
-	struct async_icount	icount;
-	struct usb_serial_port	*port;			/* loop back to the owner of this object */
-	/*Offsets*/
-	__u8		SpRegOffset;
-	__u8		ControlRegOffset;
-	__u8		DcrRegOffset;
-	/* for processing control URBS in interrupt context */
-	struct urb 	*control_urb;
-	char		*ctrl_buf;
-	int		MsrLsr;
-
-	struct urb	*write_urb_pool[NUM_URBS];
-	/* we pass a pointer to this as the arguement sent to cypress_set_termios old_termios */
-	struct ktermios	tmp_termios;        /* stores the old termios settings */
-	spinlock_t 	lock;                   /* private lock */
-};
-
-/* This structure holds all of the individual serial device information */
-struct ATENINTL_serial {
-	__u8		interrupt_in_endpoint;		/* the interrupt endpoint handle */
-	unsigned char	*interrupt_in_buffer;		/* the buffer we use for the interrupt endpoint */
-	struct urb	*interrupt_read_urb;	/* our interrupt urb */
-	__u8		bulk_in_endpoint;	/* the bulk in endpoint handle */
-	unsigned char	*bulk_in_buffer;		/* the buffer we use for the bulk in endpoint */
-	struct urb 	*read_urb;		/* our bulk read urb */
-	__u8		bulk_out_endpoint;	/* the bulk out endpoint handle */
-	struct usb_serial	*serial;	/* loop back to the owner of this object */
-	int	ATEN2011_spectrum_2or4ports; 	/* this says the number of ports in the device */
-	/* Indicates about the no.of opened ports of an individual USB-serial adapater. */
-	unsigned int	NoOfOpenPorts;
-	/* a flag for Status endpoint polling */
-	unsigned char	status_polling_started;
-};
-
-static void ATEN2011_set_termios(struct tty_struct *tty,
-				 struct usb_serial_port *port,
-				 struct ktermios *old_termios);
-static void ATEN2011_change_port_settings(struct tty_struct *tty,
-					  struct ATENINTL_port *ATEN2011_port,
-					  struct ktermios *old_termios);
-
-/*************************************
- * Bit definitions for each register *
- *************************************/
-#define LCR_BITS_5		0x00	/* 5 bits/char */
-#define LCR_BITS_6		0x01	/* 6 bits/char */
-#define LCR_BITS_7		0x02	/* 7 bits/char */
-#define LCR_BITS_8		0x03	/* 8 bits/char */
-#define LCR_BITS_MASK		0x03	/* Mask for bits/char field */
-
-#define LCR_STOP_1		0x00	/* 1 stop bit */
-#define LCR_STOP_1_5		0x04	/* 1.5 stop bits (if 5   bits/char) */
-#define LCR_STOP_2		0x04	/* 2 stop bits   (if 6-8 bits/char) */
-#define LCR_STOP_MASK		0x04	/* Mask for stop bits field */
-
-#define LCR_PAR_NONE		0x00	/* No parity */
-#define LCR_PAR_ODD		0x08	/* Odd parity */
-#define LCR_PAR_EVEN		0x18	/* Even parity */
-#define LCR_PAR_MARK		0x28	/* Force parity bit to 1 */
-#define LCR_PAR_SPACE		0x38	/* Force parity bit to 0 */
-#define LCR_PAR_MASK		0x38	/* Mask for parity field */
-
-#define LCR_SET_BREAK		0x40	/* Set Break condition */
-#define LCR_DL_ENABLE		0x80	/* Enable access to divisor latch */
-
-#define MCR_DTR			0x01	/* Assert DTR */
-#define MCR_RTS			0x02	/* Assert RTS */
-#define MCR_OUT1		0x04	/* Loopback only: Sets state of RI */
-#define MCR_MASTER_IE		0x08	/* Enable interrupt outputs */
-#define MCR_LOOPBACK		0x10	/* Set internal (digital) loopback mode */
-#define MCR_XON_ANY		0x20	/* Enable any char to exit XOFF mode */
-
-#define ATEN2011_MSR_CTS	0x10	/* Current state of CTS */
-#define ATEN2011_MSR_DSR	0x20	/* Current state of DSR */
-#define ATEN2011_MSR_RI		0x40	/* Current state of RI */
-#define ATEN2011_MSR_CD		0x80	/* Current state of CD */
-
-
-static int debug;
-
-/*
- * Version Information
- */
-#define DRIVER_VERSION "2.0"
-#define DRIVER_DESC "ATENINTL 2011 USB Serial Adapter"
-
-/*
- * Defines used for sending commands to port
- */
-
-#define ATEN_WDR_TIMEOUT	(50)	/* default urb timeout */
-
-/* Requests */
-#define ATEN_RD_RTYPE		0xC0
-#define ATEN_WR_RTYPE		0x40
-#define ATEN_RDREQ		0x0D
-#define ATEN_WRREQ		0x0E
-#define ATEN_CTRL_TIMEOUT	500
-#define VENDOR_READ_LENGTH	(0x01)
-
-/* set to 1 for RS485 mode and 0 for RS232 mode */
-/* FIXME make this somehow dynamic and not build time specific */
-static int RS485mode;
-
-static int set_reg_sync(struct usb_serial_port *port, __u16 reg, __u16 val)
-{
-	struct usb_device *dev = port->serial->dev;
-	val = val & 0x00ff;
-
-	dbg("%s: is %x, value %x", __func__, reg, val);
-
-	return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), ATEN_WRREQ,
-			       ATEN_WR_RTYPE, val, reg, NULL, 0,
-			       ATEN_WDR_TIMEOUT);
-}
-
-static int get_reg_sync(struct usb_serial_port *port, __u16 reg, __u16 *val)
-{
-	struct usb_device *dev = port->serial->dev;
-	int ret;
-
-	ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), ATEN_RDREQ,
-			      ATEN_RD_RTYPE, 0, reg, val, VENDOR_READ_LENGTH,
-			      ATEN_WDR_TIMEOUT);
-	dbg("%s: offset is %x, return val %x", __func__, reg, *val);
-	*val = (*val) & 0x00ff;
-	return ret;
-}
-
-static int set_uart_reg(struct usb_serial_port *port, __u16 reg, __u16 val)
-{
-	struct usb_device *dev = port->serial->dev;
-	struct ATENINTL_serial *a_serial;
-	__u16 minor;
-
-	a_serial = usb_get_serial_data(port->serial);
-	minor = port->serial->minor;
-	if (minor == SERIAL_TTY_NO_MINOR)
-		minor = 0;
-	val = val & 0x00ff;
-
-	/*
-	 * For the UART control registers,
-	 * the application number need to be Or'ed
-	 */
-	if (a_serial->ATEN2011_spectrum_2or4ports == 4)
-		val |= (((__u16)port->number - minor) + 1) << 8;
-	else {
-		if (((__u16) port->number - minor) == 0)
-			val |= (((__u16)port->number - minor) + 1) << 8;
-		else
-			val |= (((__u16)port->number - minor) + 2) << 8;
-	}
-	dbg("%s: application number is %x", __func__, val);
-
-	return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), ATEN_WRREQ,
-			       ATEN_WR_RTYPE, val, reg, NULL, 0,
-			       ATEN_WDR_TIMEOUT);
-}
-
-static int get_uart_reg(struct usb_serial_port *port, __u16 reg, __u16 *val)
-{
-	struct usb_device *dev = port->serial->dev;
-	int ret = 0;
-	__u16 wval;
-	struct ATENINTL_serial *a_serial;
-	__u16 minor = port->serial->minor;
-
-	a_serial = usb_get_serial_data(port->serial);
-	if (minor == SERIAL_TTY_NO_MINOR)
-		minor = 0;
-
-	/* wval is same as application number */
-	if (a_serial->ATEN2011_spectrum_2or4ports == 4)
-		wval = (((__u16)port->number - minor) + 1) << 8;
-	else {
-		if (((__u16) port->number - minor) == 0)
-			wval = (((__u16) port->number - minor) + 1) << 8;
-		else
-			wval = (((__u16) port->number - minor) + 2) << 8;
-	}
-	dbg("%s: application number is %x", __func__, wval);
-	ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), ATEN_RDREQ,
-			      ATEN_RD_RTYPE, wval, reg, val, VENDOR_READ_LENGTH,
-			      ATEN_WDR_TIMEOUT);
-	*val = (*val) & 0x00ff;
-	return ret;
-}
-
-static int handle_newMsr(struct ATENINTL_port *port, __u8 newMsr)
-{
-	struct ATENINTL_port *ATEN2011_port;
-	struct async_icount *icount;
-	ATEN2011_port = port;
-	icount = &ATEN2011_port->icount;
-	if (newMsr &
-	    (ATEN_MSR_DELTA_CTS | ATEN_MSR_DELTA_DSR | ATEN_MSR_DELTA_RI |
-	     ATEN_MSR_DELTA_CD)) {
-		icount = &ATEN2011_port->icount;
-
-		/* update input line counters */
-		if (newMsr & ATEN_MSR_DELTA_CTS)
-			icount->cts++;
-		if (newMsr & ATEN_MSR_DELTA_DSR)
-			icount->dsr++;
-		if (newMsr & ATEN_MSR_DELTA_CD)
-			icount->dcd++;
-		if (newMsr & ATEN_MSR_DELTA_RI)
-			icount->rng++;
-	}
-
-	return 0;
-}
-
-static int handle_newLsr(struct ATENINTL_port *port, __u8 newLsr)
-{
-	struct async_icount *icount;
-
-	dbg("%s - %02x", __func__, newLsr);
-
-	if (newLsr & SERIAL_LSR_BI) {
-		/*
-		 * Parity and Framing errors only count if they occur exclusive
-		 * of a break being received.
-		 */
-		newLsr &= (__u8) (SERIAL_LSR_OE | SERIAL_LSR_BI);
-	}
-
-	/* update input line counters */
-	icount = &port->icount;
-	if (newLsr & SERIAL_LSR_BI)
-		icount->brk++;
-	if (newLsr & SERIAL_LSR_OE)
-		icount->overrun++;
-	if (newLsr & SERIAL_LSR_PE)
-		icount->parity++;
-	if (newLsr & SERIAL_LSR_FE)
-		icount->frame++;
-
-	return 0;
-}
-
-static void ATEN2011_control_callback(struct urb *urb)
-{
-	unsigned char *data;
-	struct ATENINTL_port *ATEN2011_port;
-	__u8 regval = 0x0;
-
-	switch (urb->status) {
-	case 0:
-		/* success */
-		break;
-	case -ECONNRESET:
-	case -ENOENT:
-	case -ESHUTDOWN:
-		/* this urb is terminated, clean up */
-		dbg("%s - urb shutting down with status: %d", __func__,
-		    urb->status);
-		return;
-	default:
-		dbg("%s - nonzero urb status received: %d", __func__,
-		    urb->status);
-		goto exit;
-	}
-
-	ATEN2011_port = (struct ATENINTL_port *)urb->context;
-
-	dbg("%s urb buffer size is %d", __func__, urb->actual_length);
-	dbg("%s ATEN2011_port->MsrLsr is %d port %d", __func__,
-		ATEN2011_port->MsrLsr, ATEN2011_port->port_num);
-	data = urb->transfer_buffer;
-	regval = (__u8) data[0];
-	dbg("%s data is %x", __func__, regval);
-	if (ATEN2011_port->MsrLsr == 0)
-		handle_newMsr(ATEN2011_port, regval);
-	else if (ATEN2011_port->MsrLsr == 1)
-		handle_newLsr(ATEN2011_port, regval);
-
-exit:
-	return;
-}
-
-static int ATEN2011_get_reg(struct ATENINTL_port *ATEN, __u16 Wval, __u16 reg,
-			    __u16 *val)
-{
-	struct usb_device *dev = ATEN->port->serial->dev;
-	struct usb_ctrlrequest *dr = NULL;
-	unsigned char *buffer = NULL;
-	int ret = 0;
-	buffer = (__u8 *) ATEN->ctrl_buf;
-
-	dr = (void *)(buffer + 2);
-	dr->bRequestType = ATEN_RD_RTYPE;
-	dr->bRequest = ATEN_RDREQ;
-	dr->wValue = cpu_to_le16(Wval);
-	dr->wIndex = cpu_to_le16(reg);
-	dr->wLength = cpu_to_le16(2);
-
-	usb_fill_control_urb(ATEN->control_urb, dev, usb_rcvctrlpipe(dev, 0),
-			     (unsigned char *)dr, buffer, 2,
-			     ATEN2011_control_callback, ATEN);
-	ATEN->control_urb->transfer_buffer_length = 2;
-	ret = usb_submit_urb(ATEN->control_urb, GFP_ATOMIC);
-	return ret;
-}
-
-static void ATEN2011_interrupt_callback(struct urb *urb)
-{
-	int result;
-	int length;
-	struct ATENINTL_port *ATEN2011_port;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct usb_serial *serial;
-	__u16 Data;
-	unsigned char *data;
-	__u8 sp[5], st;
-	int i;
-	__u16 wval;
-	int minor;
-
-	dbg("%s", " : Entering");
-
-	ATEN2011_serial = (struct ATENINTL_serial *)urb->context;
-
-	switch (urb->status) {
-	case 0:
-		/* success */
-		break;
-	case -ECONNRESET:
-	case -ENOENT:
-	case -ESHUTDOWN:
-		/* this urb is terminated, clean up */
-		dbg("%s - urb shutting down with status: %d", __func__,
-		    urb->status);
-		return;
-	default:
-		dbg("%s - nonzero urb status received: %d", __func__,
-		    urb->status);
-		goto exit;
-	}
-	length = urb->actual_length;
-	data = urb->transfer_buffer;
-
-	serial = ATEN2011_serial->serial;
-
-	/* ATENINTL get 5 bytes
-	 * Byte 1 IIR Port 1 (port.number is 0)
-	 * Byte 2 IIR Port 2 (port.number is 1)
-	 * Byte 3 IIR Port 3 (port.number is 2)
-	 * Byte 4 IIR Port 4 (port.number is 3)
-	 * Byte 5 FIFO status for both */
-
-	if (length && length > 5) {
-		dbg("%s", "Wrong data !!!");
-		return;
-	}
-
-	/* MATRIX */
-	if (ATEN2011_serial->ATEN2011_spectrum_2or4ports == 4) {
-		sp[0] = (__u8) data[0];
-		sp[1] = (__u8) data[1];
-		sp[2] = (__u8) data[2];
-		sp[3] = (__u8) data[3];
-		st = (__u8) data[4];
-	} else {
-		sp[0] = (__u8) data[0];
-		sp[1] = (__u8) data[2];
-		/* sp[2]=(__u8)data[2]; */
-		/* sp[3]=(__u8)data[3]; */
-		st = (__u8) data[4];
-
-	}
-	for (i = 0; i < serial->num_ports; i++) {
-		ATEN2011_port = usb_get_serial_port_data(serial->port[i]);
-		minor = serial->minor;
-		if (minor == SERIAL_TTY_NO_MINOR)
-			minor = 0;
-		if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)
-		    && (i != 0))
-			wval =
-			    (((__u16) serial->port[i]->number -
-			      (__u16) (minor)) + 2) << 8;
-		else
-			wval =
-			    (((__u16) serial->port[i]->number -
-			      (__u16) (minor)) + 1) << 8;
-		if (ATEN2011_port->open != 0) {
-			if (sp[i] & 0x01) {
-				dbg("SP%d No Interrupt !!!", i);
-			} else {
-				switch (sp[i] & 0x0f) {
-				case SERIAL_IIR_RLS:
-					dbg("Serial Port %d: Receiver status error or address bit detected in 9-bit mode", i);
-					ATEN2011_port->MsrLsr = 1;
-					ATEN2011_get_reg(ATEN2011_port, wval,
-							 LINE_STATUS_REGISTER,
-							 &Data);
-					break;
-				case SERIAL_IIR_MS:
-					dbg("Serial Port %d: Modem status change", i);
-					ATEN2011_port->MsrLsr = 0;
-					ATEN2011_get_reg(ATEN2011_port, wval,
-							 MODEM_STATUS_REGISTER,
-							 &Data);
-					break;
-				}
-			}
-		}
-
-	}
-exit:
-	if (ATEN2011_serial->status_polling_started == 0)
-		return;
-
-	result = usb_submit_urb(urb, GFP_ATOMIC);
-	if (result) {
-		dev_err(&urb->dev->dev,
-			"%s - Error %d submitting interrupt urb\n",
-			__func__, result);
-	}
-
-	return;
-}
-
-static void ATEN2011_bulk_in_callback(struct urb *urb)
-{
-	int status;
-	unsigned char *data;
-	struct usb_serial *serial;
-	struct usb_serial_port *port;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct ATENINTL_port *ATEN2011_port;
-	struct tty_struct *tty;
-
-	if (urb->status) {
-		dbg("nonzero read bulk status received: %d", urb->status);
-		return;
-	}
-
-	ATEN2011_port = (struct ATENINTL_port *)urb->context;
-
-	port = (struct usb_serial_port *)ATEN2011_port->port;
-	serial = port->serial;
-
-	dbg("%s", "Entering...");
-
-	data = urb->transfer_buffer;
-	ATEN2011_serial = usb_get_serial_data(serial);
-
-	if (urb->actual_length) {
-		tty = tty_port_tty_get(&ATEN2011_port->port->port);
-		if (tty) {
-			tty_buffer_request_room(tty, urb->actual_length);
-			tty_insert_flip_string(tty, data, urb->actual_length);
-			tty_flip_buffer_push(tty);
-			tty_kref_put(tty);
-		}
-
-		ATEN2011_port->icount.rx += urb->actual_length;
-		dbg("ATEN2011_port->icount.rx is %d:",
-			ATEN2011_port->icount.rx);
-	}
-
-	if (!ATEN2011_port->read_urb) {
-		dbg("%s", "URB KILLED !!!");
-		return;
-	}
-
-	if (ATEN2011_port->read_urb->status != -EINPROGRESS) {
-		ATEN2011_port->read_urb->dev = serial->dev;
-
-		status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC);
-		if (status)
-			dbg("usb_submit_urb(read bulk) failed, status = %d", status);
-	}
-}
-
-static void ATEN2011_bulk_out_data_callback(struct urb *urb)
-{
-	struct ATENINTL_port *ATEN2011_port;
-	struct tty_struct *tty;
-
-	if (urb->status) {
-		dbg("nonzero write bulk status received:%d", urb->status);
-		return;
-	}
-
-	ATEN2011_port = (struct ATENINTL_port *)urb->context;
-
-	dbg("%s", "Entering .........");
-
-	tty = tty_port_tty_get(&ATEN2011_port->port->port);
-
-	if (tty && ATEN2011_port->open)
-		/* tell the tty driver that something has changed */
-		tty_wakeup(tty);
-
-	/* schedule_work(&ATEN2011_port->port->work); */
-	tty_kref_put(tty);
-
-}
-
-#ifdef ATENSerialProbe
-static int ATEN2011_serial_probe(struct usb_serial *serial,
-				 const struct usb_device_id *id)
-{
-
-	/*need to implement the mode_reg reading and updating\
-	   structures usb_serial_ device_type\
-	   (i.e num_ports, num_bulkin,bulkout etc) */
-	/* Also we can update the changes  attach */
-	return 1;
-}
-#endif
-
-static int ATEN2011_open(struct tty_struct *tty, struct usb_serial_port *port,
-			 struct file *filp)
-{
-	int response;
-	int j;
-	struct usb_serial *serial;
-	struct urb *urb;
-	__u16 Data;
-	int status;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct ATENINTL_port *ATEN2011_port;
-	struct ktermios tmp_termios;
-	int minor;
-
-	serial = port->serial;
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return -ENODEV;
-
-	ATEN2011_serial = usb_get_serial_data(serial);
-	if (ATEN2011_serial == NULL)
-		return -ENODEV;
-
-	/* increment the number of opened ports counter here */
-	ATEN2011_serial->NoOfOpenPorts++;
-
-	usb_clear_halt(serial->dev, port->write_urb->pipe);
-	usb_clear_halt(serial->dev, port->read_urb->pipe);
-
-	/* Initialising the write urb pool */
-	for (j = 0; j < NUM_URBS; ++j) {
-		urb = usb_alloc_urb(0, GFP_ATOMIC);
-		ATEN2011_port->write_urb_pool[j] = urb;
-
-		if (urb == NULL) {
-			err("No more urbs???");
-			continue;
-		}
-
-		urb->transfer_buffer = NULL;
-		urb->transfer_buffer =
-		    kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL);
-		if (!urb->transfer_buffer) {
-			err("%s-out of memory for urb buffers.", __func__);
-			continue;
-		}
-	}
-
-/*****************************************************************************
- * Initialize ATEN2011 -- Write Init values to corresponding Registers
- *
- * Register Index
- * 1 : IER
- * 2 : FCR
- * 3 : LCR
- * 4 : MCR
- *
- * 0x08 : SP1/2 Control Reg
- *****************************************************************************/
-
-/* NEED to check the fallowing Block */
-
-	Data = 0x0;
-	status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data);
-	if (status < 0) {
-		dbg("Reading Spreg failed");
-		return -1;
-	}
-	Data |= 0x80;
-	status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-	if (status < 0) {
-		dbg("writing Spreg failed");
-		return -1;
-	}
-
-	Data &= ~0x80;
-	status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-	if (status < 0) {
-		dbg("writing Spreg failed");
-		return -1;
-	}
-
-/* End of block to be checked */
-/**************************CHECK***************************/
-
-	if (RS485mode == 0)
-		Data = 0xC0;
-	else
-		Data = 0x00;
-	status = set_uart_reg(port, SCRATCH_PAD_REGISTER, Data);
-	if (status < 0) {
-		dbg("Writing SCRATCH_PAD_REGISTER failed status-0x%x", status);
-		return -1;
-	} else
-		dbg("SCRATCH_PAD_REGISTER Writing success status%d", status);
-
-/**************************CHECK***************************/
-
-	Data = 0x0;
-	status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data);
-	if (status < 0) {
-		dbg("Reading Controlreg failed");
-		return -1;
-	}
-	Data |= 0x08;		/* Driver done bit */
-	Data |= 0x20;		/* rx_disable */
-	status = 0;
-	status =
-	    set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data);
-	if (status < 0) {
-		dbg("writing Controlreg failed");
-		return -1;
-	}
-	/*
-	 * do register settings here
-	 * Set all regs to the device default values.
-	 * First Disable all interrupts.
-	 */
-
-	Data = 0x00;
-	status = set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-	if (status < 0) {
-		dbg("disableing interrupts failed");
-		return -1;
-	}
-	/* Set FIFO_CONTROL_REGISTER to the default value */
-	Data = 0x00;
-	status = set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
-	if (status < 0) {
-		dbg("Writing FIFO_CONTROL_REGISTER  failed");
-		return -1;
-	}
-
-	Data = 0xcf;		/* chk */
-	status = set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
-	if (status < 0) {
-		dbg("Writing FIFO_CONTROL_REGISTER  failed");
-		return -1;
-	}
-
-	Data = 0x03;		/* LCR_BITS_8 */
-	status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-	ATEN2011_port->shadowLCR = Data;
-
-	Data = 0x0b;		/* MCR_DTR|MCR_RTS|MCR_MASTER_IE */
-	status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-	ATEN2011_port->shadowMCR = Data;
-
-#ifdef Check
-	Data = 0x00;
-	status = get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
-	ATEN2011_port->shadowLCR = Data;
-
-	Data |= SERIAL_LCR_DLAB;	/* data latch enable in LCR 0x80 */
-	status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
-	Data = 0x0c;
-	status = set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
-
-	Data = 0x0;
-	status = set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
-
-	Data = 0x00;
-	status = get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
-
-/*      Data = ATEN2011_port->shadowLCR; */	/* data latch disable */
-	Data = Data & ~SERIAL_LCR_DLAB;
-	status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-	ATEN2011_port->shadowLCR = Data;
-#endif
-	/* clearing Bulkin and Bulkout Fifo */
-	Data = 0x0;
-	status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data);
-
-	Data = Data | 0x0c;
-	status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-
-	Data = Data & ~0x0c;
-	status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-	/* Finally enable all interrupts */
-	Data = 0x0;
-	Data = 0x0c;
-	status = set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
-	/* clearing rx_disable */
-	Data = 0x0;
-	status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data);
-	Data = Data & ~0x20;
-	status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data);
-
-	/* rx_negate */
-	Data = 0x0;
-	status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data);
-	Data = Data | 0x10;
-	status = 0;
-	status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data);
-
-	/*
-	 * Check to see if we've set up our endpoint info yet
-	 * (can't set it up in ATEN2011_startup as the structures
-	 * were not set up at that time.)
-	 */
-	if (ATEN2011_serial->NoOfOpenPorts == 1) {
-		/* start the status polling here */
-		ATEN2011_serial->status_polling_started = 1;
-		/* If not yet set, Set here */
-		ATEN2011_serial->interrupt_in_buffer =
-		    serial->port[0]->interrupt_in_buffer;
-		ATEN2011_serial->interrupt_in_endpoint =
-		    serial->port[0]->interrupt_in_endpointAddress;
-		ATEN2011_serial->interrupt_read_urb =
-		    serial->port[0]->interrupt_in_urb;
-
-		/* set up interrupt urb */
-		usb_fill_int_urb(ATEN2011_serial->interrupt_read_urb,
-				 serial->dev,
-				 usb_rcvintpipe(serial->dev,
-						ATEN2011_serial->
-						interrupt_in_endpoint),
-				 ATEN2011_serial->interrupt_in_buffer,
-				 ATEN2011_serial->interrupt_read_urb->
-				 transfer_buffer_length,
-				 ATEN2011_interrupt_callback, ATEN2011_serial,
-				 ATEN2011_serial->interrupt_read_urb->interval);
-
-		/* start interrupt read for ATEN2011               *
-		 * will continue as long as ATEN2011 is connected  */
-
-		response =
-		    usb_submit_urb(ATEN2011_serial->interrupt_read_urb,
-				   GFP_KERNEL);
-		if (response) {
-			dbg("%s - Error %d submitting interrupt urb",
-				__func__, response);
-		}
-
-	}
-
-	/*
-	 * See if we've set up our endpoint info yet
-	 * (can't set it up in ATEN2011_startup as the
-	 * structures were not set up at that time.)
-	 */
-
-	dbg("port number is %d", port->number);
-	dbg("serial number is %d", port->serial->minor);
-	dbg("Bulkin endpoint is %d", port->bulk_in_endpointAddress);
-	dbg("BulkOut endpoint is %d", port->bulk_out_endpointAddress);
-	dbg("Interrupt endpoint is %d",
-		port->interrupt_in_endpointAddress);
-	dbg("port's number in the device is %d", ATEN2011_port->port_num);
-	ATEN2011_port->bulk_in_buffer = port->bulk_in_buffer;
-	ATEN2011_port->bulk_in_endpoint = port->bulk_in_endpointAddress;
-	ATEN2011_port->read_urb = port->read_urb;
-	ATEN2011_port->bulk_out_endpoint = port->bulk_out_endpointAddress;
-
-	minor = port->serial->minor;
-	if (minor == SERIAL_TTY_NO_MINOR)
-		minor = 0;
-
-	/* set up our bulk in urb */
-	if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)
-	    && (((__u16) port->number - (__u16) (minor)) != 0)) {
-		usb_fill_bulk_urb(ATEN2011_port->read_urb, serial->dev,
-				  usb_rcvbulkpipe(serial->dev,
-						  (port->
-						   bulk_in_endpointAddress +
-						   2)), port->bulk_in_buffer,
-				  ATEN2011_port->read_urb->
-				  transfer_buffer_length,
-				  ATEN2011_bulk_in_callback, ATEN2011_port);
-	} else
-		usb_fill_bulk_urb(ATEN2011_port->read_urb,
-				  serial->dev,
-				  usb_rcvbulkpipe(serial->dev,
-						  port->
-						  bulk_in_endpointAddress),
-				  port->bulk_in_buffer,
-				  ATEN2011_port->read_urb->
-				  transfer_buffer_length,
-				  ATEN2011_bulk_in_callback, ATEN2011_port);
-
-	dbg("ATEN2011_open: bulkin endpoint is %d",
-		port->bulk_in_endpointAddress);
-	response = usb_submit_urb(ATEN2011_port->read_urb, GFP_KERNEL);
-	if (response) {
-		err("%s - Error %d submitting control urb", __func__,
-		    response);
-	}
-
-	/* initialize our wait queues */
-	init_waitqueue_head(&ATEN2011_port->wait_chase);
-	init_waitqueue_head(&ATEN2011_port->wait_command);
-
-	/* initialize our icount structure */
-	memset(&(ATEN2011_port->icount), 0x00, sizeof(ATEN2011_port->icount));
-
-	/* initialize our port settings */
-	ATEN2011_port->shadowMCR = MCR_MASTER_IE;	/* Must set to enable ints! */
-	ATEN2011_port->chaseResponsePending = 0;
-	/* send a open port command */
-	ATEN2011_port->open = 1;
-	/* ATEN2011_change_port_settings(ATEN2011_port,old_termios); */
-	/* Setup termios */
-	ATEN2011_set_termios(tty, port, &tmp_termios);
-	ATEN2011_port->icount.tx = 0;
-	ATEN2011_port->icount.rx = 0;
-
-	dbg("usb_serial serial:%x       ATEN2011_port:%x\nATEN2011_serial:%x      usb_serial_port port:%x",
-	     (unsigned int)serial, (unsigned int)ATEN2011_port,
-	     (unsigned int)ATEN2011_serial, (unsigned int)port);
-
-	return 0;
-
-}
-
-static int ATEN2011_chars_in_buffer(struct tty_struct *tty)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	int i;
-	int chars = 0;
-	struct ATENINTL_port *ATEN2011_port;
-
-	/* dbg("%s"," ATEN2011_chars_in_buffer:entering ..........."); */
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-	if (ATEN2011_port == NULL) {
-		dbg("%s", "ATEN2011_break:leaving ...........");
-		return -1;
-	}
-
-	for (i = 0; i < NUM_URBS; ++i)
-		if (ATEN2011_port->write_urb_pool[i]->status == -EINPROGRESS)
-			chars += URB_TRANSFER_BUFFER_SIZE;
-
-	dbg("%s - returns %d", __func__, chars);
-	return chars;
-
-}
-
-static void ATEN2011_block_until_tx_empty(struct tty_struct *tty,
-					  struct ATENINTL_port *ATEN2011_port)
-{
-	int timeout = HZ / 10;
-	int wait = 30;
-	int count;
-
-	while (1) {
-		count = ATEN2011_chars_in_buffer(tty);
-
-		/* Check for Buffer status */
-		if (count <= 0)
-			return;
-
-		/* Block the thread for a while */
-		interruptible_sleep_on_timeout(&ATEN2011_port->wait_chase,
-					       timeout);
-
-		/* No activity.. count down section */
-		wait--;
-		if (wait == 0) {
-			dbg("%s - TIMEOUT", __func__);
-			return;
-		} else {
-			/* Reset timout value back to seconds */
-			wait = 30;
-		}
-	}
-}
-
-static void ATEN2011_close(struct tty_struct *tty, struct usb_serial_port *port,
-			   struct file *filp)
-{
-	struct usb_serial *serial;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct ATENINTL_port *ATEN2011_port;
-	int no_urbs;
-	__u16 Data;
-
-	dbg("%s", "ATEN2011_close:entering...");
-	serial = port->serial;
-
-	/* take the Adpater and port's private data */
-	ATEN2011_serial = usb_get_serial_data(serial);
-	ATEN2011_port = usb_get_serial_port_data(port);
-	if ((ATEN2011_serial == NULL) || (ATEN2011_port == NULL))
-		return;
-
-	if (serial->dev) {
-		/* flush and block(wait) until tx is empty */
-		ATEN2011_block_until_tx_empty(tty, ATEN2011_port);
-	}
-	/* kill the ports URB's */
-	for (no_urbs = 0; no_urbs < NUM_URBS; no_urbs++)
-		usb_kill_urb(ATEN2011_port->write_urb_pool[no_urbs]);
-	/* Freeing Write URBs */
-	for (no_urbs = 0; no_urbs < NUM_URBS; ++no_urbs) {
-		kfree(ATEN2011_port->write_urb_pool[no_urbs]->transfer_buffer);
-		usb_free_urb(ATEN2011_port->write_urb_pool[no_urbs]);
-	}
-	/* While closing port, shutdown all bulk read, write  *
-	 * and interrupt read if they exists                  */
-	if (serial->dev) {
-		if (ATEN2011_port->write_urb) {
-			dbg("%s", "Shutdown bulk write");
-			usb_kill_urb(ATEN2011_port->write_urb);
-		}
-		if (ATEN2011_port->read_urb) {
-			dbg("%s", "Shutdown bulk read");
-			usb_kill_urb(ATEN2011_port->read_urb);
-		}
-		if ((&ATEN2011_port->control_urb)) {
-			dbg("%s", "Shutdown control read");
-			/* usb_kill_urb (ATEN2011_port->control_urb); */
-
-		}
-	}
-	/* if(ATEN2011_port->ctrl_buf != NULL) */
-		/* kfree(ATEN2011_port->ctrl_buf); */
-	/* decrement the no.of open ports counter of an individual USB-serial adapter. */
-	ATEN2011_serial->NoOfOpenPorts--;
-	dbg("NoOfOpenPorts in close%d:in port%d",
-		ATEN2011_serial->NoOfOpenPorts, port->number);
-	if (ATEN2011_serial->NoOfOpenPorts == 0) {
-		/* stop the stus polling here */
-		ATEN2011_serial->status_polling_started = 0;
-		if (ATEN2011_serial->interrupt_read_urb) {
-			dbg("%s", "Shutdown interrupt_read_urb");
-			/* ATEN2011_serial->interrupt_in_buffer=NULL; */
-			/* usb_kill_urb (ATEN2011_serial->interrupt_read_urb); */
-		}
-	}
-	if (ATEN2011_port->write_urb) {
-		/* if this urb had a transfer buffer already (old tx) free it */
-		kfree(ATEN2011_port->write_urb->transfer_buffer);
-		usb_free_urb(ATEN2011_port->write_urb);
-	}
-
-	/* clear the MCR & IER */
-	Data = 0x00;
-	set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-	Data = 0x00;
-	set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
-	ATEN2011_port->open = 0;
-	dbg("%s", "Leaving ............");
-
-}
-
-static void ATEN2011_block_until_chase_response(struct tty_struct *tty,
-						struct ATENINTL_port
-						*ATEN2011_port)
-{
-	int timeout = 1 * HZ;
-	int wait = 10;
-	int count;
-
-	while (1) {
-		count = ATEN2011_chars_in_buffer(tty);
-
-		/* Check for Buffer status */
-		if (count <= 0) {
-			ATEN2011_port->chaseResponsePending = 0;
-			return;
-		}
-
-		/* Block the thread for a while */
-		interruptible_sleep_on_timeout(&ATEN2011_port->wait_chase,
-					       timeout);
-		/* No activity.. count down section */
-		wait--;
-		if (wait == 0) {
-			dbg("%s - TIMEOUT", __func__);
-			return;
-		} else {
-			/* Reset timout value back to seconds */
-			wait = 10;
-		}
-	}
-
-}
-
-static void ATEN2011_break(struct tty_struct *tty, int break_state)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	unsigned char data;
-	struct usb_serial *serial;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct ATENINTL_port *ATEN2011_port;
-
-	dbg("%s", "Entering ...........");
-	dbg("ATEN2011_break: Start");
-
-	serial = port->serial;
-
-	ATEN2011_serial = usb_get_serial_data(serial);
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if ((ATEN2011_serial == NULL) || (ATEN2011_port == NULL))
-		return;
-
-	/* flush and chase */
-	ATEN2011_port->chaseResponsePending = 1;
-
-	if (serial->dev) {
-		/* flush and block until tx is empty */
-		ATEN2011_block_until_chase_response(tty, ATEN2011_port);
-	}
-
-	if (break_state == -1)
-		data = ATEN2011_port->shadowLCR | LCR_SET_BREAK;
-	else
-		data = ATEN2011_port->shadowLCR & ~LCR_SET_BREAK;
-
-	ATEN2011_port->shadowLCR = data;
-	dbg("ATEN2011_break ATEN2011_port->shadowLCR is %x",
-		ATEN2011_port->shadowLCR);
-	set_uart_reg(port, LINE_CONTROL_REGISTER, ATEN2011_port->shadowLCR);
-
-	return;
-}
-
-static int ATEN2011_write_room(struct tty_struct *tty)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	int i;
-	int room = 0;
-	struct ATENINTL_port *ATEN2011_port;
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-	if (ATEN2011_port == NULL) {
-		dbg("%s", "ATEN2011_break:leaving ...........");
-		return -1;
-	}
-
-	for (i = 0; i < NUM_URBS; ++i)
-		if (ATEN2011_port->write_urb_pool[i]->status != -EINPROGRESS)
-			room += URB_TRANSFER_BUFFER_SIZE;
-
-	dbg("%s - returns %d", __func__, room);
-	return room;
-
-}
-
-static int ATEN2011_write(struct tty_struct *tty, struct usb_serial_port *port,
-			  const unsigned char *data, int count)
-{
-	int status;
-	int i;
-	int bytes_sent = 0;
-	int transfer_size;
-	int minor;
-
-	struct ATENINTL_port *ATEN2011_port;
-	struct usb_serial *serial;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct urb *urb;
-	const unsigned char *current_position = data;
-	unsigned char *data1;
-	dbg("%s", "entering ...........");
-
-	serial = port->serial;
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-	if (ATEN2011_port == NULL) {
-		dbg("%s", "ATEN2011_port is NULL");
-		return -1;
-	}
-
-	ATEN2011_serial = usb_get_serial_data(serial);
-	if (ATEN2011_serial == NULL) {
-		dbg("%s", "ATEN2011_serial is NULL");
-		return -1;
-	}
-
-	/* try to find a free urb in the list */
-	urb = NULL;
-
-	for (i = 0; i < NUM_URBS; ++i) {
-		if (ATEN2011_port->write_urb_pool[i]->status != -EINPROGRESS) {
-			urb = ATEN2011_port->write_urb_pool[i];
-			dbg("URB:%d", i);
-			break;
-		}
-	}
-
-	if (urb == NULL) {
-		dbg("%s - no more free urbs", __func__);
-		goto exit;
-	}
-
-	if (urb->transfer_buffer == NULL) {
-		urb->transfer_buffer =
-		    kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL);
-
-		if (urb->transfer_buffer == NULL) {
-			err("%s no more kernel memory...", __func__);
-			goto exit;
-		}
-	}
-	transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE);
-
-	memcpy(urb->transfer_buffer, current_position, transfer_size);
-	/* usb_serial_debug_data (__FILE__, __func__, transfer_size, urb->transfer_buffer); */
-
-	/* fill urb with data and submit  */
-	minor = port->serial->minor;
-	if (minor == SERIAL_TTY_NO_MINOR)
-		minor = 0;
-	if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)
-	    && (((__u16) port->number - (__u16) (minor)) != 0)) {
-		usb_fill_bulk_urb(urb, ATEN2011_serial->serial->dev,
-				  usb_sndbulkpipe(ATEN2011_serial->serial->dev,
-						  (port->
-						   bulk_out_endpointAddress) +
-						  2), urb->transfer_buffer,
-				  transfer_size,
-				  ATEN2011_bulk_out_data_callback,
-				  ATEN2011_port);
-	} else
-
-		usb_fill_bulk_urb(urb,
-				  ATEN2011_serial->serial->dev,
-				  usb_sndbulkpipe(ATEN2011_serial->serial->dev,
-						  port->
-						  bulk_out_endpointAddress),
-				  urb->transfer_buffer, transfer_size,
-				  ATEN2011_bulk_out_data_callback,
-				  ATEN2011_port);
-
-	data1 = urb->transfer_buffer;
-	dbg("bulkout endpoint is %d", port->bulk_out_endpointAddress);
-	/* for(i=0;i < urb->actual_length;i++) */
-		/* dbg("Data is %c ",data1[i]); */
-
-	/* send it down the pipe */
-	status = usb_submit_urb(urb, GFP_ATOMIC);
-
-	if (status) {
-		err("%s - usb_submit_urb(write bulk) failed with status = %d",
-		    __func__, status);
-		bytes_sent = status;
-		goto exit;
-	}
-	bytes_sent = transfer_size;
-	ATEN2011_port->icount.tx += transfer_size;
-	dbg("ATEN2011_port->icount.tx is %d:", ATEN2011_port->icount.tx);
-
-exit:
-	return bytes_sent;
-}
-
-static void ATEN2011_throttle(struct tty_struct *tty)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	struct ATENINTL_port *ATEN2011_port;
-	int status;
-
-	dbg("- port %d", port->number);
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return;
-
-	if (!ATEN2011_port->open) {
-		dbg("%s", "port not opened");
-		return;
-	}
-
-	dbg("%s", "Entering .......... ");
-
-	if (!tty) {
-		dbg("%s - no tty available", __func__);
-		return;
-	}
-
-	/* if we are implementing XON/XOFF, send the stop character */
-	if (I_IXOFF(tty)) {
-		unsigned char stop_char = STOP_CHAR(tty);
-		status = ATEN2011_write(tty, port, &stop_char, 1);
-		if (status <= 0)
-			return;
-	}
-
-	/* if we are implementing RTS/CTS, toggle that line */
-	if (tty->termios->c_cflag & CRTSCTS) {
-		ATEN2011_port->shadowMCR &= ~MCR_RTS;
-		status = set_uart_reg(port, MODEM_CONTROL_REGISTER,
-				      ATEN2011_port->shadowMCR);
-		if (status < 0)
-			return;
-	}
-
-	return;
-}
-
-static void ATEN2011_unthrottle(struct tty_struct *tty)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	int status;
-	struct ATENINTL_port *ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return;
-
-	if (!ATEN2011_port->open) {
-		dbg("%s - port not opened", __func__);
-		return;
-	}
-
-	dbg("%s", "Entering .......... ");
-
-	if (!tty) {
-		dbg("%s - no tty available", __func__);
-		return;
-	}
-
-	/* if we are implementing XON/XOFF, send the start character */
-	if (I_IXOFF(tty)) {
-		unsigned char start_char = START_CHAR(tty);
-		status = ATEN2011_write(tty, port, &start_char, 1);
-		if (status <= 0)
-			return;
-	}
-
-	/* if we are implementing RTS/CTS, toggle that line */
-	if (tty->termios->c_cflag & CRTSCTS) {
-		ATEN2011_port->shadowMCR |= MCR_RTS;
-		status = set_uart_reg(port, MODEM_CONTROL_REGISTER,
-				      ATEN2011_port->shadowMCR);
-		if (status < 0)
-			return;
-	}
-
-	return;
-}
-
-static int ATEN2011_tiocmget(struct tty_struct *tty, struct file *file)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	struct ATENINTL_port *ATEN2011_port;
-	unsigned int result;
-	__u16 msr;
-	__u16 mcr;
-	/* unsigned int mcr; */
-	int status = 0;
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	dbg("%s - port %d", __func__, port->number);
-
-	if (ATEN2011_port == NULL)
-		return -ENODEV;
-
-	status = get_uart_reg(port, MODEM_STATUS_REGISTER, &msr);
-	status = get_uart_reg(port, MODEM_CONTROL_REGISTER, &mcr);
-	/* mcr = ATEN2011_port->shadowMCR; */
-	/* COMMENT2: the Fallowing three line are commented for updating only MSR values */
-	result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0)
-	    | ((mcr & MCR_RTS) ? TIOCM_RTS : 0)
-	    | ((mcr & MCR_LOOPBACK) ? TIOCM_LOOP : 0)
-	    | ((msr & ATEN2011_MSR_CTS) ? TIOCM_CTS : 0)
-	    | ((msr & ATEN2011_MSR_CD) ? TIOCM_CAR : 0)
-	    | ((msr & ATEN2011_MSR_RI) ? TIOCM_RI : 0)
-	    | ((msr & ATEN2011_MSR_DSR) ? TIOCM_DSR : 0);
-
-	dbg("%s - 0x%04X", __func__, result);
-
-	return result;
-}
-
-static int ATEN2011_tiocmset(struct tty_struct *tty, struct file *file,
-			     unsigned int set, unsigned int clear)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	struct ATENINTL_port *ATEN2011_port;
-	unsigned int mcr;
-	unsigned int status;
-
-	dbg("%s - port %d", __func__, port->number);
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return -ENODEV;
-
-	mcr = ATEN2011_port->shadowMCR;
-	if (clear & TIOCM_RTS)
-		mcr &= ~MCR_RTS;
-	if (clear & TIOCM_DTR)
-		mcr &= ~MCR_DTR;
-	if (clear & TIOCM_LOOP)
-		mcr &= ~MCR_LOOPBACK;
-
-	if (set & TIOCM_RTS)
-		mcr |= MCR_RTS;
-	if (set & TIOCM_DTR)
-		mcr |= MCR_DTR;
-	if (set & TIOCM_LOOP)
-		mcr |= MCR_LOOPBACK;
-
-	ATEN2011_port->shadowMCR = mcr;
-
-	status = set_uart_reg(port, MODEM_CONTROL_REGISTER, mcr);
-	if (status < 0) {
-		dbg("setting MODEM_CONTROL_REGISTER Failed");
-		return -1;
-	}
-
-	return 0;
-}
-
-static void ATEN2011_set_termios(struct tty_struct *tty,
-				 struct usb_serial_port *port,
-				 struct ktermios *old_termios)
-{
-	int status;
-	unsigned int cflag;
-	struct usb_serial *serial;
-	struct ATENINTL_port *ATEN2011_port;
-
-	dbg("ATEN2011_set_termios: START");
-
-	serial = port->serial;
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return;
-
-	if (!ATEN2011_port->open) {
-		dbg("%s - port not opened", __func__);
-		return;
-	}
-
-	dbg("%s", "setting termios - ");
-
-	cflag = tty->termios->c_cflag;
-
-	dbg("%s - cflag %08x iflag %08x", __func__,
-	    tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag));
-
-	if (old_termios) {
-		dbg("%s - old clfag %08x old iflag %08x", __func__,
-		    old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag));
-	}
-
-	dbg("%s - port %d", __func__, port->number);
-
-	/* change the port settings to the new ones specified */
-
-	ATEN2011_change_port_settings(tty, ATEN2011_port, old_termios);
-
-	if (!ATEN2011_port->read_urb) {
-		dbg("%s", "URB KILLED !!!!!");
-		return;
-	}
-
-	if (ATEN2011_port->read_urb->status != -EINPROGRESS) {
-		ATEN2011_port->read_urb->dev = serial->dev;
-		status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC);
-		if (status) {
-			dbg
-			    (" usb_submit_urb(read bulk) failed, status = %d",
-			     status);
-		}
-	}
-	return;
-}
-
-static int get_lsr_info(struct tty_struct *tty,
-			struct ATENINTL_port *ATEN2011_port,
-			unsigned int __user *value)
-{
-	int count;
-	unsigned int result = 0;
-
-	count = ATEN2011_chars_in_buffer(tty);
-	if (count == 0) {
-		dbg("%s -- Empty", __func__);
-		result = TIOCSER_TEMT;
-	}
-
-	if (copy_to_user(value, &result, sizeof(int)))
-		return -EFAULT;
-	return 0;
-}
-
-static int get_number_bytes_avail(struct tty_struct *tty,
-				  struct ATENINTL_port *ATEN2011_port,
-				  unsigned int __user *value)
-{
-	unsigned int result = 0;
-
-	if (!tty)
-		return -ENOIOCTLCMD;
-
-	result = tty->read_cnt;
-
-	dbg("%s(%d) = %d", __func__, ATEN2011_port->port->number, result);
-	if (copy_to_user(value, &result, sizeof(int)))
-		return -EFAULT;
-
-	return -ENOIOCTLCMD;
-}
-
-static int set_modem_info(struct ATENINTL_port *ATEN2011_port, unsigned int cmd,
-			  unsigned int __user *value)
-{
-	unsigned int mcr;
-	unsigned int arg;
-	__u16 Data;
-	int status;
-	struct usb_serial_port *port;
-
-	if (ATEN2011_port == NULL)
-		return -1;
-
-	port = (struct usb_serial_port *)ATEN2011_port->port;
-
-	mcr = ATEN2011_port->shadowMCR;
-
-	if (copy_from_user(&arg, value, sizeof(int)))
-		return -EFAULT;
-
-	switch (cmd) {
-	case TIOCMBIS:
-		if (arg & TIOCM_RTS)
-			mcr |= MCR_RTS;
-		if (arg & TIOCM_DTR)
-			mcr |= MCR_RTS;
-		if (arg & TIOCM_LOOP)
-			mcr |= MCR_LOOPBACK;
-		break;
-
-	case TIOCMBIC:
-		if (arg & TIOCM_RTS)
-			mcr &= ~MCR_RTS;
-		if (arg & TIOCM_DTR)
-			mcr &= ~MCR_RTS;
-		if (arg & TIOCM_LOOP)
-			mcr &= ~MCR_LOOPBACK;
-		break;
-
-	case TIOCMSET:
-		/* turn off the RTS and DTR and LOOPBACK
-		 * and then only turn on what was asked to */
-		mcr &= ~(MCR_RTS | MCR_DTR | MCR_LOOPBACK);
-		mcr |= ((arg & TIOCM_RTS) ? MCR_RTS : 0);
-		mcr |= ((arg & TIOCM_DTR) ? MCR_DTR : 0);
-		mcr |= ((arg & TIOCM_LOOP) ? MCR_LOOPBACK : 0);
-		break;
-	}
-
-	ATEN2011_port->shadowMCR = mcr;
-
-	Data = ATEN2011_port->shadowMCR;
-	status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-	if (status < 0) {
-		dbg("setting MODEM_CONTROL_REGISTER Failed");
-		return -1;
-	}
-
-	return 0;
-}
-
-static int get_modem_info(struct ATENINTL_port *ATEN2011_port,
-			  unsigned int __user *value)
-{
-	unsigned int result = 0;
-	__u16 msr;
-	unsigned int mcr = ATEN2011_port->shadowMCR;
-	int status;
-
-	status = get_uart_reg(ATEN2011_port->port, MODEM_STATUS_REGISTER, &msr);
-	result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0)	/* 0x002 */
-	    |((mcr & MCR_RTS) ? TIOCM_RTS : 0)	/* 0x004 */
-	    |((msr & ATEN2011_MSR_CTS) ? TIOCM_CTS : 0)	/* 0x020 */
-	    |((msr & ATEN2011_MSR_CD) ? TIOCM_CAR : 0)	/* 0x040 */
-	    |((msr & ATEN2011_MSR_RI) ? TIOCM_RI : 0)	/* 0x080 */
-	    |((msr & ATEN2011_MSR_DSR) ? TIOCM_DSR : 0);	/* 0x100 */
-
-	dbg("%s -- %x", __func__, result);
-
-	if (copy_to_user(value, &result, sizeof(int)))
-		return -EFAULT;
-	return 0;
-}
-
-static int get_serial_info(struct ATENINTL_port *ATEN2011_port,
-			   struct serial_struct __user *retinfo)
-{
-	struct serial_struct tmp;
-
-	if (ATEN2011_port == NULL)
-		return -1;
-
-	if (!retinfo)
-		return -EFAULT;
-
-	memset(&tmp, 0, sizeof(tmp));
-
-	tmp.type = PORT_16550A;
-	tmp.line = ATEN2011_port->port->serial->minor;
-	if (tmp.line == SERIAL_TTY_NO_MINOR)
-		tmp.line = 0;
-	tmp.port = ATEN2011_port->port->number;
-	tmp.irq = 0;
-	tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
-	tmp.xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE;
-	tmp.baud_base = 9600;
-	tmp.close_delay = 5 * HZ;
-	tmp.closing_wait = 30 * HZ;
-
-	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
-		return -EFAULT;
-	return 0;
-}
-
-static int ATEN2011_ioctl(struct tty_struct *tty, struct file *file,
-			  unsigned int cmd, unsigned long arg)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	struct ATENINTL_port *ATEN2011_port;
-	struct async_icount cnow;
-	struct async_icount cprev;
-	struct serial_icounter_struct icount;
-	int ATENret = 0;
-	unsigned int __user *user_arg = (unsigned int __user *)arg;
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return -1;
-
-	dbg("%s - port %d, cmd = 0x%x", __func__, port->number, cmd);
-
-	switch (cmd) {
-		/* return number of bytes available */
-
-	case TIOCINQ:
-		dbg("%s (%d) TIOCINQ", __func__, port->number);
-		return get_number_bytes_avail(tty, ATEN2011_port, user_arg);
-		break;
-
-	case TIOCOUTQ:
-		dbg("%s (%d) TIOCOUTQ", __func__, port->number);
-		return put_user(ATEN2011_chars_in_buffer(tty), user_arg);
-		break;
-
-	case TIOCSERGETLSR:
-		dbg("%s (%d) TIOCSERGETLSR", __func__, port->number);
-		return get_lsr_info(tty, ATEN2011_port, user_arg);
-		return 0;
-
-	case TIOCMBIS:
-	case TIOCMBIC:
-	case TIOCMSET:
-		dbg("%s (%d) TIOCMSET/TIOCMBIC/TIOCMSET", __func__,
-		    port->number);
-		ATENret = set_modem_info(ATEN2011_port, cmd, user_arg);
-		return ATENret;
-
-	case TIOCMGET:
-		dbg("%s (%d) TIOCMGET", __func__, port->number);
-		return get_modem_info(ATEN2011_port, user_arg);
-
-	case TIOCGSERIAL:
-		dbg("%s (%d) TIOCGSERIAL", __func__, port->number);
-		return get_serial_info(ATEN2011_port,
-				       (struct serial_struct __user *)arg);
-
-	case TIOCSSERIAL:
-		dbg("%s (%d) TIOCSSERIAL", __func__, port->number);
-		break;
-
-	case TIOCMIWAIT:
-		dbg("%s (%d) TIOCMIWAIT", __func__, port->number);
-		cprev = ATEN2011_port->icount;
-		while (1) {
-			/* see if a signal did it */
-			if (signal_pending(current))
-				return -ERESTARTSYS;
-			cnow = ATEN2011_port->icount;
-			if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
-			    cnow.dcd == cprev.dcd && cnow.cts == cprev.cts)
-				return -EIO;	/* no change => error */
-			if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) ||
-			    ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) ||
-			    ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) ||
-			    ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) {
-				return 0;
-			}
-			cprev = cnow;
-		}
-		/* NOTREACHED */
-		break;
-
-	case TIOCGICOUNT:
-		cnow = ATEN2011_port->icount;
-		icount.cts = cnow.cts;
-		icount.dsr = cnow.dsr;
-		icount.rng = cnow.rng;
-		icount.dcd = cnow.dcd;
-		icount.rx = cnow.rx;
-		icount.tx = cnow.tx;
-		icount.frame = cnow.frame;
-		icount.overrun = cnow.overrun;
-		icount.parity = cnow.parity;
-		icount.brk = cnow.brk;
-		icount.buf_overrun = cnow.buf_overrun;
-
-		dbg("%s (%d) TIOCGICOUNT RX=%d, TX=%d", __func__,
-		    port->number, icount.rx, icount.tx);
-		if (copy_to_user((void __user *)arg, &icount, sizeof(icount)))
-			return -EFAULT;
-		return 0;
-
-	default:
-		break;
-	}
-
-	return -ENOIOCTLCMD;
-}
-
-static int ATEN2011_calc_baud_rate_divisor(int baudRate, int *divisor,
-					   __u16 *clk_sel_val)
-{
-	dbg("%s - %d", __func__, baudRate);
-
-	if (baudRate <= 115200) {
-		*divisor = 115200 / baudRate;
-		*clk_sel_val = 0x0;
-	}
-	if ((baudRate > 115200) && (baudRate <= 230400)) {
-		*divisor = 230400 / baudRate;
-		*clk_sel_val = 0x10;
-	} else if ((baudRate > 230400) && (baudRate <= 403200)) {
-		*divisor = 403200 / baudRate;
-		*clk_sel_val = 0x20;
-	} else if ((baudRate > 403200) && (baudRate <= 460800)) {
-		*divisor = 460800 / baudRate;
-		*clk_sel_val = 0x30;
-	} else if ((baudRate > 460800) && (baudRate <= 806400)) {
-		*divisor = 806400 / baudRate;
-		*clk_sel_val = 0x40;
-	} else if ((baudRate > 806400) && (baudRate <= 921600)) {
-		*divisor = 921600 / baudRate;
-		*clk_sel_val = 0x50;
-	} else if ((baudRate > 921600) && (baudRate <= 1572864)) {
-		*divisor = 1572864 / baudRate;
-		*clk_sel_val = 0x60;
-	} else if ((baudRate > 1572864) && (baudRate <= 3145728)) {
-		*divisor = 3145728 / baudRate;
-		*clk_sel_val = 0x70;
-	}
-	return 0;
-}
-
-static int ATEN2011_send_cmd_write_baud_rate(struct ATENINTL_port
-					     *ATEN2011_port, int baudRate)
-{
-	int divisor = 0;
-	int status;
-	__u16 Data;
-	unsigned char number;
-	__u16 clk_sel_val;
-	struct usb_serial_port *port;
-	int minor;
-
-	if (ATEN2011_port == NULL)
-		return -1;
-
-	port = (struct usb_serial_port *)ATEN2011_port->port;
-
-	dbg("%s", "Entering .......... ");
-
-	minor = ATEN2011_port->port->serial->minor;
-	if (minor == SERIAL_TTY_NO_MINOR)
-		minor = 0;
-	number = ATEN2011_port->port->number - minor;
-
-	dbg("%s - port = %d, baud = %d", __func__,
-	    ATEN2011_port->port->number, baudRate);
-	/* reset clk_uart_sel in spregOffset */
-	if (baudRate > 115200) {
-#ifdef HW_flow_control
-		/*
-		 * NOTE: need to see the pther register to modify
-		 * setting h/w flow control bit to 1;
-		 */
-		/* Data = ATEN2011_port->shadowMCR; */
-		Data = 0x2b;
-		ATEN2011_port->shadowMCR = Data;
-		status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-		if (status < 0) {
-			dbg("Writing spreg failed in set_serial_baud");
-			return -1;
-		}
-#endif
-
-	} else {
-#ifdef HW_flow_control
-		/* setting h/w flow control bit to 0; */
-		/* Data = ATEN2011_port->shadowMCR; */
-		Data = 0xb;
-		ATEN2011_port->shadowMCR = Data;
-		status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-		if (status < 0) {
-			dbg("Writing spreg failed in set_serial_baud");
-			return -1;
-		}
-#endif
-
-	}
-
-	if (1)			/* baudRate <= 115200) */ {
-		clk_sel_val = 0x0;
-		Data = 0x0;
-		status =
-		    ATEN2011_calc_baud_rate_divisor(baudRate, &divisor,
-						    &clk_sel_val);
-		status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data);
-		if (status < 0) {
-			dbg("reading spreg failed in set_serial_baud");
-			return -1;
-		}
-		Data = (Data & 0x8f) | clk_sel_val;
-		status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-		if (status < 0) {
-			dbg("Writing spreg failed in set_serial_baud");
-			return -1;
-		}
-		/* Calculate the Divisor */
-
-		if (status) {
-			err("%s - bad baud rate", __func__);
-			dbg("%s", "bad baud rate");
-			return status;
-		}
-		/* Enable access to divisor latch */
-		Data = ATEN2011_port->shadowLCR | SERIAL_LCR_DLAB;
-		ATEN2011_port->shadowLCR = Data;
-		set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
-		/* Write the divisor */
-		Data = (unsigned char)(divisor & 0xff);
-		dbg("set_serial_baud Value to write DLL is %x", Data);
-		set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
-
-		Data = (unsigned char)((divisor & 0xff00) >> 8);
-		dbg("set_serial_baud Value to write DLM is %x", Data);
-		set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
-
-		/* Disable access to divisor latch */
-		Data = ATEN2011_port->shadowLCR & ~SERIAL_LCR_DLAB;
-		ATEN2011_port->shadowLCR = Data;
-		set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
-	}
-
-	return status;
-}
-
-static void ATEN2011_change_port_settings(struct tty_struct *tty,
-					  struct ATENINTL_port *ATEN2011_port,
-					  struct ktermios *old_termios)
-{
-	int baud;
-	unsigned cflag;
-	unsigned iflag;
-	__u8 lData;
-	__u8 lParity;
-	__u8 lStop;
-	int status;
-	__u16 Data;
-	struct usb_serial_port *port;
-	struct usb_serial *serial;
-
-	if (ATEN2011_port == NULL)
-		return;
-
-	port = (struct usb_serial_port *)ATEN2011_port->port;
-
-	serial = port->serial;
-
-	dbg("%s - port %d", __func__, ATEN2011_port->port->number);
-
-	if (!ATEN2011_port->open) {
-		dbg("%s - port not opened", __func__);
-		return;
-	}
-
-	if ((!tty) || (!tty->termios)) {
-		dbg("%s - no tty structures", __func__);
-		return;
-	}
-
-	dbg("%s", "Entering .......... ");
-
-	lData = LCR_BITS_8;
-	lStop = LCR_STOP_1;
-	lParity = LCR_PAR_NONE;
-
-	cflag = tty->termios->c_cflag;
-	iflag = tty->termios->c_iflag;
-
-	/* Change the number of bits */
-
-	/* COMMENT1: the below Line"if(cflag & CSIZE)" is added for the errors we get for serial loop data test i.e serial_loopback.pl -v */
-	/* if(cflag & CSIZE) */
-	{
-		switch (cflag & CSIZE) {
-		case CS5:
-			lData = LCR_BITS_5;
-			break;
-
-		case CS6:
-			lData = LCR_BITS_6;
-			break;
-
-		case CS7:
-			lData = LCR_BITS_7;
-			break;
-		default:
-		case CS8:
-			lData = LCR_BITS_8;
-			break;
-		}
-	}
-	/* Change the Parity bit */
-	if (cflag & PARENB) {
-		if (cflag & PARODD) {
-			lParity = LCR_PAR_ODD;
-			dbg("%s - parity = odd", __func__);
-		} else {
-			lParity = LCR_PAR_EVEN;
-			dbg("%s - parity = even", __func__);
-		}
-
-	} else {
-		dbg("%s - parity = none", __func__);
-	}
-
-	if (cflag & CMSPAR)
-		lParity = lParity | 0x20;
-
-	/* Change the Stop bit */
-	if (cflag & CSTOPB) {
-		lStop = LCR_STOP_2;
-		dbg("%s - stop bits = 2", __func__);
-	} else {
-		lStop = LCR_STOP_1;
-		dbg("%s - stop bits = 1", __func__);
-	}
-
-	/* Update the LCR with the correct value */
-	ATEN2011_port->shadowLCR &=
-	    ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK);
-	ATEN2011_port->shadowLCR |= (lData | lParity | lStop);
-
-	dbg
-	    ("ATEN2011_change_port_settings ATEN2011_port->shadowLCR is %x",
-	     ATEN2011_port->shadowLCR);
-	/* Disable Interrupts */
-	Data = 0x00;
-	set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
-	Data = 0x00;
-	set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
-
-	Data = 0xcf;
-	set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
-
-	/* Send the updated LCR value to the ATEN2011 */
-	Data = ATEN2011_port->shadowLCR;
-
-	set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
-	Data = 0x00b;
-	ATEN2011_port->shadowMCR = Data;
-	set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-	Data = 0x00b;
-	set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-
-	/* set up the MCR register and send it to the ATEN2011 */
-
-	ATEN2011_port->shadowMCR = MCR_MASTER_IE;
-	if (cflag & CBAUD)
-		ATEN2011_port->shadowMCR |= (MCR_DTR | MCR_RTS);
-
-	if (cflag & CRTSCTS)
-		ATEN2011_port->shadowMCR |= (MCR_XON_ANY);
-	else
-		ATEN2011_port->shadowMCR &= ~(MCR_XON_ANY);
-
-	Data = ATEN2011_port->shadowMCR;
-	set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-
-	/* Determine divisor based on baud rate */
-	baud = tty_get_baud_rate(tty);
-
-	if (!baud) {
-		/* pick a default, any default... */
-		dbg("%s", "Picked default baud...");
-		baud = 9600;
-	}
-
-	dbg("%s - baud rate = %d", __func__, baud);
-	status = ATEN2011_send_cmd_write_baud_rate(ATEN2011_port, baud);
-
-	/* Enable Interrupts */
-	Data = 0x0c;
-	set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
-	if (ATEN2011_port->read_urb->status != -EINPROGRESS) {
-		ATEN2011_port->read_urb->dev = serial->dev;
-
-		status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC);
-
-		if (status) {
-			dbg
-			    (" usb_submit_urb(read bulk) failed, status = %d",
-			     status);
-		}
-	}
-	dbg
-	    ("ATEN2011_change_port_settings ATEN2011_port->shadowLCR is End %x",
-	     ATEN2011_port->shadowLCR);
-
-	return;
-}
-
-static int ATEN2011_calc_num_ports(struct usb_serial *serial)
-{
-
-	__u16 Data = 0x00;
-	int ret = 0;
-	int ATEN2011_2or4ports;
-	ret = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
-			      ATEN_RDREQ, ATEN_RD_RTYPE, 0, GPIO_REGISTER,
-			      &Data, VENDOR_READ_LENGTH, ATEN_WDR_TIMEOUT);
-
-/* ghostgum: here is where the problem appears to bet */
-/* Which of the following are needed? */
-/* Greg used the serial->type->num_ports=2 */
-/* But the code in the ATEN2011_open relies on serial->num_ports=2 */
-	if ((Data & 0x01) == 0) {
-		ATEN2011_2or4ports = 2;
-		serial->type->num_ports = 2;
-		serial->num_ports = 2;
-	}
-	/* else if(serial->interface->cur_altsetting->desc.bNumEndpoints == 9) */
-	else {
-		ATEN2011_2or4ports = 4;
-		serial->type->num_ports = 4;
-		serial->num_ports = 4;
-
-	}
-
-	return ATEN2011_2or4ports;
-}
-
-static int ATEN2011_startup(struct usb_serial *serial)
-{
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct ATENINTL_port *ATEN2011_port;
-	struct usb_device *dev;
-	int i, status;
-	int minor;
-
-	__u16 Data;
-	dbg("%s", " ATEN2011_startup :entering..........");
-
-	if (!serial) {
-		dbg("%s", "Invalid Handler");
-		return -1;
-	}
-
-	dev = serial->dev;
-
-	dbg("%s", "Entering...");
-
-	/* create our private serial structure */
-	ATEN2011_serial = kzalloc(sizeof(struct ATENINTL_serial), GFP_KERNEL);
-	if (ATEN2011_serial == NULL) {
-		err("%s - Out of memory", __func__);
-		return -ENOMEM;
-	}
-
-	/* resetting the private structure field values to zero */
-	memset(ATEN2011_serial, 0, sizeof(struct ATENINTL_serial));
-
-	ATEN2011_serial->serial = serial;
-	/* initilize status polling flag to 0 */
-	ATEN2011_serial->status_polling_started = 0;
-
-	usb_set_serial_data(serial, ATEN2011_serial);
-	ATEN2011_serial->ATEN2011_spectrum_2or4ports =
-	    ATEN2011_calc_num_ports(serial);
-	/* we set up the pointers to the endpoints in the ATEN2011_open *
-	 * function, as the structures aren't created yet.             */
-
-	/* set up port private structures */
-	for (i = 0; i < serial->num_ports; ++i) {
-		ATEN2011_port =
-		    kmalloc(sizeof(struct ATENINTL_port), GFP_KERNEL);
-		if (ATEN2011_port == NULL) {
-			err("%s - Out of memory", __func__);
-			usb_set_serial_data(serial, NULL);
-			kfree(ATEN2011_serial);
-			return -ENOMEM;
-		}
-		memset(ATEN2011_port, 0, sizeof(struct ATENINTL_port));
-
-		/*
-		 * Initialize all port interrupt end point to port 0
-		 * int endpoint. Our device has only one interrupt end point
-		 * comman to all port
-		 */
-		/* serial->port[i]->interrupt_in_endpointAddress = serial->port[0]->interrupt_in_endpointAddress; */
-
-		ATEN2011_port->port = serial->port[i];
-		usb_set_serial_port_data(serial->port[i], ATEN2011_port);
-
-		minor = serial->port[i]->serial->minor;
-		if (minor == SERIAL_TTY_NO_MINOR)
-			minor = 0;
-		ATEN2011_port->port_num =
-		    ((serial->port[i]->number - minor) + 1);
-
-		if (ATEN2011_port->port_num == 1) {
-			ATEN2011_port->SpRegOffset = 0x0;
-			ATEN2011_port->ControlRegOffset = 0x1;
-			ATEN2011_port->DcrRegOffset = 0x4;
-		} else if ((ATEN2011_port->port_num == 2)
-			   && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
-			       4)) {
-			ATEN2011_port->SpRegOffset = 0x8;
-			ATEN2011_port->ControlRegOffset = 0x9;
-			ATEN2011_port->DcrRegOffset = 0x16;
-		} else if ((ATEN2011_port->port_num == 2)
-			   && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
-			       2)) {
-			ATEN2011_port->SpRegOffset = 0xa;
-			ATEN2011_port->ControlRegOffset = 0xb;
-			ATEN2011_port->DcrRegOffset = 0x19;
-		} else if ((ATEN2011_port->port_num == 3)
-			   && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
-			       4)) {
-			ATEN2011_port->SpRegOffset = 0xa;
-			ATEN2011_port->ControlRegOffset = 0xb;
-			ATEN2011_port->DcrRegOffset = 0x19;
-		} else if ((ATEN2011_port->port_num == 4)
-			   && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
-			       4)) {
-			ATEN2011_port->SpRegOffset = 0xc;
-			ATEN2011_port->ControlRegOffset = 0xd;
-			ATEN2011_port->DcrRegOffset = 0x1c;
-		}
-
-		usb_set_serial_port_data(serial->port[i], ATEN2011_port);
-
-		/* enable rx_disable bit in control register */
-
-		status = get_reg_sync(serial->port[i],
-				      ATEN2011_port->ControlRegOffset, &Data);
-		if (status < 0) {
-			dbg("Reading ControlReg failed status-0x%x",
-				status);
-			break;
-		} else
-			dbg
-			    ("ControlReg Reading success val is %x, status%d",
-			     Data, status);
-		Data |= 0x08;	/* setting driver done bit */
-		Data |= 0x04;	/* sp1_bit to have cts change reflect in modem status reg */
-
-		/* Data |= 0x20; */	/* rx_disable bit */
-		status = set_reg_sync(serial->port[i],
-				      ATEN2011_port->ControlRegOffset, Data);
-		if (status < 0) {
-			dbg
-			    ("Writing ControlReg failed(rx_disable) status-0x%x",
-			     status);
-			break;
-		} else
-			dbg
-			    ("ControlReg Writing success(rx_disable) status%d",
-			     status);
-
-		/*
-		 * Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2
-		 * and 0x24 in DCR3
-		 */
-		Data = 0x01;
-		status = set_reg_sync(serial->port[i],
-				      (__u16)(ATEN2011_port->DcrRegOffset + 0),
-				      Data);
-		if (status < 0) {
-			dbg("Writing DCR0 failed status-0x%x", status);
-			break;
-		} else
-			dbg("DCR0 Writing success status%d", status);
-
-		Data = 0x05;
-		status = set_reg_sync(serial->port[i],
-				      (__u16)(ATEN2011_port->DcrRegOffset + 1),
-				      Data);
-		if (status < 0) {
-			dbg("Writing DCR1 failed status-0x%x", status);
-			break;
-		} else
-			dbg("DCR1 Writing success status%d", status);
-
-		Data = 0x24;
-		status = set_reg_sync(serial->port[i],
-				      (__u16)(ATEN2011_port->DcrRegOffset + 2),
-				      Data);
-		if (status < 0) {
-			dbg("Writing DCR2 failed status-0x%x", status);
-			break;
-		} else
-			dbg("DCR2 Writing success status%d", status);
-
-		/* write values in clkstart0x0 and clkmulti 0x20 */
-		Data = 0x0;
-		status = set_reg_sync(serial->port[i], CLK_START_VALUE_REGISTER,
-				      Data);
-		if (status < 0) {
-			dbg
-			    ("Writing CLK_START_VALUE_REGISTER failed status-0x%x",
-			     status);
-			break;
-		} else
-			dbg
-			    ("CLK_START_VALUE_REGISTER Writing success status%d",
-			     status);
-
-		Data = 0x20;
-		status = set_reg_sync(serial->port[i], CLK_MULTI_REGISTER,
-				      Data);
-		if (status < 0) {
-			dbg
-			    ("Writing CLK_MULTI_REGISTER failed status-0x%x",
-			     status);
-			break;
-		} else
-			dbg("CLK_MULTI_REGISTER Writing success status%d",
-				status);
-
-		/* Zero Length flag register */
-		if ((ATEN2011_port->port_num != 1)
-		    && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)) {
-
-			Data = 0xff;
-			status = set_reg_sync(serial->port[i],
-					      (__u16)(ZLP_REG1 + ((__u16)ATEN2011_port->port_num)),
-					      Data);
-			dbg("ZLIP offset%x",
-				(__u16) (ZLP_REG1 +
-					 ((__u16) ATEN2011_port->port_num)));
-			if (status < 0) {
-				dbg
-				    ("Writing ZLP_REG%d failed status-0x%x",
-				     i + 2, status);
-				break;
-			} else
-				dbg("ZLP_REG%d Writing success status%d",
-					i + 2, status);
-		} else {
-			Data = 0xff;
-			status = set_reg_sync(serial->port[i],
-					      (__u16)(ZLP_REG1 + ((__u16)ATEN2011_port->port_num) - 0x1),
-					      Data);
-			dbg("ZLIP offset%x",
-				(__u16) (ZLP_REG1 +
-					 ((__u16) ATEN2011_port->port_num) -
-					 0x1));
-			if (status < 0) {
-				dbg
-				    ("Writing ZLP_REG%d failed status-0x%x",
-				     i + 1, status);
-				break;
-			} else
-				dbg("ZLP_REG%d Writing success status%d",
-					i + 1, status);
-
-		}
-		ATEN2011_port->control_urb = usb_alloc_urb(0, GFP_ATOMIC);
-		ATEN2011_port->ctrl_buf = kmalloc(16, GFP_KERNEL);
-
-	}
-
-	/* Zero Length flag enable */
-	Data = 0x0f;
-	status = set_reg_sync(serial->port[0], ZLP_REG5, Data);
-	if (status < 0) {
-		dbg("Writing ZLP_REG5 failed status-0x%x", status);
-		return -1;
-	} else
-		dbg("ZLP_REG5 Writing success status%d", status);
-
-	/* setting configuration feature to one */
-	usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
-			(__u8) 0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5 * HZ);
-	return 0;
-}
-
-static void ATEN2011_release(struct usb_serial *serial)
-{
-	int i;
-	struct ATENINTL_port *ATEN2011_port;
-
-	/* check for the ports to be closed,close the ports and disconnect */
-
-	/* free private structure allocated for serial port  *
-	 * stop reads and writes on all ports                */
-
-	for (i = 0; i < serial->num_ports; ++i) {
-		ATEN2011_port = usb_get_serial_port_data(serial->port[i]);
-		kfree(ATEN2011_port->ctrl_buf);
-		usb_kill_urb(ATEN2011_port->control_urb);
-		kfree(ATEN2011_port);
-		usb_set_serial_port_data(serial->port[i], NULL);
-	}
-
-	/* free private structure allocated for serial device */
-
-	kfree(usb_get_serial_data(serial));
-	usb_set_serial_data(serial, NULL);
-}
-
-static struct usb_serial_driver aten_serial_driver = {
-	.driver = {
-		.owner =	THIS_MODULE,
-		.name =		"aten2011",
-		},
-	.description =		DRIVER_DESC,
-	.id_table =		id_table,
-	.open =			ATEN2011_open,
-	.close =		ATEN2011_close,
-	.write =		ATEN2011_write,
-	.write_room =		ATEN2011_write_room,
-	.chars_in_buffer =	ATEN2011_chars_in_buffer,
-	.throttle =		ATEN2011_throttle,
-	.unthrottle =		ATEN2011_unthrottle,
-	.calc_num_ports =	ATEN2011_calc_num_ports,
-
-	.ioctl =		ATEN2011_ioctl,
-	.set_termios =		ATEN2011_set_termios,
-	.break_ctl =		ATEN2011_break,
-	.tiocmget =		ATEN2011_tiocmget,
-	.tiocmset =		ATEN2011_tiocmset,
-	.attach =		ATEN2011_startup,
-	.release =		ATEN2011_release,
-	.read_bulk_callback =	ATEN2011_bulk_in_callback,
-	.read_int_callback =	ATEN2011_interrupt_callback,
-};
-
-static struct usb_driver aten_driver = {
-	.name =		"aten2011",
-	.probe =	usb_serial_probe,
-	.disconnect =	usb_serial_disconnect,
-	.id_table =	id_table,
-};
-
-static int __init aten_init(void)
-{
-	int retval;
-
-	/* Register with the usb serial */
-	retval = usb_serial_register(&aten_serial_driver);
-	if (retval)
-		return retval;
-
-	printk(KERN_INFO KBUILD_MODNAME ":"
-	       DRIVER_DESC " " DRIVER_VERSION "\n");
-
-	/* Register with the usb */
-	retval = usb_register(&aten_driver);
-	if (retval)
-		usb_serial_deregister(&aten_serial_driver);
-
-	return retval;
-}
-
-static void __exit aten_exit(void)
-{
-	usb_deregister(&aten_driver);
-	usb_serial_deregister(&aten_serial_driver);
-}
-
-module_init(aten_init);
-module_exit(aten_exit);
-
-/* Module information */
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_LICENSE("GPL");
-
-MODULE_PARM_DESC(debug, "Debug enabled or not");
-- 
GitLab


From fb29900217bd89370974870d47cab07bad3e5ac4 Mon Sep 17 00:00:00 2001
From: Amit Kucheria <amit.kucheria@canonical.com>
Date: Mon, 27 Jul 2009 12:01:03 +0300
Subject: [PATCH 0155/1153] staging: udlfb: Add vmalloc.h include

Required for vmalloc_32 and vfree declarations on non-x86 platforms.

Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/staging/udlfb/udlfb.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/staging/udlfb/udlfb.c b/drivers/staging/udlfb/udlfb.c
index 0ab9d15f343..f5416af1e90 100644
--- a/drivers/staging/udlfb/udlfb.c
+++ b/drivers/staging/udlfb/udlfb.c
@@ -21,6 +21,7 @@
 #include <linux/mm.h>
 #include <linux/fb.h>
 #include <linux/mutex.h>
+#include <linux/vmalloc.h>
 
 #include "udlfb.h"
 
-- 
GitLab


From 38ceb592fcac9110c6b3c87ea0a27bff68c43486 Mon Sep 17 00:00:00 2001
From: Lai Jiangshan <laijs@cn.fujitsu.com>
Date: Tue, 28 Jul 2009 20:11:24 +0800
Subject: [PATCH 0156/1153] tracing: Fix invalid function_graph entry

When print_graph_entry() computes a function call entry event, it needs
to also check the next entry to guess if it matches the return event of
the current function entry.
In order to look at this next event, it needs to consume the current
entry before going ahead in the ring buffer.

However, if the current event that gets consumed is the last one in the
ring buffer head page, the ring_buffer may reuse the page for writers.
The consumed entry will then become invalid because of possible
racy overwriting.

Me must then handle this entry by making a copy of it.

The fix also applies on 2.6.30

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: stable@kernel.org
LKML-Reference: <4A6EEAEC.3050508@cn.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
---
 kernel/trace/trace_functions_graph.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/kernel/trace/trace_functions_graph.c b/kernel/trace/trace_functions_graph.c
index d2249abafb5..420ec348757 100644
--- a/kernel/trace/trace_functions_graph.c
+++ b/kernel/trace/trace_functions_graph.c
@@ -843,9 +843,16 @@ print_graph_function(struct trace_iterator *iter)
 
 	switch (entry->type) {
 	case TRACE_GRAPH_ENT: {
-		struct ftrace_graph_ent_entry *field;
+		/*
+		 * print_graph_entry() may consume the current event,
+		 * thus @field may become invalid, so we need to save it.
+		 * sizeof(struct ftrace_graph_ent_entry) is very small,
+		 * it can be safely saved at the stack.
+		 */
+		struct ftrace_graph_ent_entry *field, saved;
 		trace_assign_type(field, entry);
-		return print_graph_entry(field, s, iter);
+		saved = *field;
+		return print_graph_entry(&saved, s, iter);
 	}
 	case TRACE_GRAPH_RET: {
 		struct ftrace_graph_ret_entry *field;
-- 
GitLab


From 74e7ff8c50b6b022e6ffaa736b16a4dc161d3eaf Mon Sep 17 00:00:00 2001
From: Lai Jiangshan <laijs@cn.fujitsu.com>
Date: Tue, 28 Jul 2009 20:17:22 +0800
Subject: [PATCH 0157/1153] tracing: Fix missing function_graph events when we
 splice_read from trace_pipe

About a half events are missing when we splice_read
from trace_pipe. They are unexpectedly consumed because we ignore
the TRACE_TYPE_NO_CONSUME return value used by the function graph
tracer when it needs to consume the events by itself to walk on
the ring buffer.

The same problem appears with ftrace_dump()

Example of an output before this patch:

1)               |      ktime_get_real() {
1)   2.846 us    |          read_hpet();
1)   4.558 us    |        }
1)   6.195 us    |      }

After this patch:

0)               |      ktime_get_real() {
0)               |        getnstimeofday() {
0)   1.960 us    |          read_hpet();
0)   3.597 us    |        }
0)   5.196 us    |      }

The fix also applies on 2.6.30

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: stable@kernel.org
LKML-Reference: <4A6EEC52.90704@cn.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
---
 kernel/trace/trace.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/kernel/trace/trace.c b/kernel/trace/trace.c
index 8bc8d8afea6..da984ad065a 100644
--- a/kernel/trace/trace.c
+++ b/kernel/trace/trace.c
@@ -3085,7 +3085,8 @@ tracing_fill_pipe_page(size_t rem, struct trace_iterator *iter)
 			break;
 		}
 
-		trace_consume(iter);
+		if (ret != TRACE_TYPE_NO_CONSUME)
+			trace_consume(iter);
 		rem -= count;
 		if (!find_next_entry_inc(iter))	{
 			rem = 0;
@@ -4233,8 +4234,11 @@ static void __ftrace_dump(bool disable_tracing)
 		iter.pos = -1;
 
 		if (find_next_entry_inc(&iter) != NULL) {
-			print_trace_line(&iter);
-			trace_consume(&iter);
+			int ret;
+
+			ret = print_trace_line(&iter);
+			if (ret != TRACE_TYPE_NO_CONSUME)
+				trace_consume(&iter);
 		}
 
 		trace_printk_seq(&iter.seq);
-- 
GitLab


From 6352a29305373ae6196491e6d4669f301e26492e Mon Sep 17 00:00:00 2001
From: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Date: Tue, 28 Jul 2009 13:57:01 -0500
Subject: [PATCH 0158/1153] eCryptfs: Check Tag 11 literal data buffer size

Tag 11 packets are stored in the metadata section of an eCryptfs file to
store the key signature(s) used to encrypt the file encryption key.
After extracting the packet length field to determine the key signature
length, a check is not performed to see if the length would exceed the
key signature buffer size that was passed into parse_tag_11_packet().

Thanks to Ramon de Carvalho Valle for finding this bug using fsfuzzer.

Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Cc: stable@kernel.org (2.6.27 and 30)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/ecryptfs/keystore.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/fs/ecryptfs/keystore.c b/fs/ecryptfs/keystore.c
index af737bb56cb..5414253d4c9 100644
--- a/fs/ecryptfs/keystore.c
+++ b/fs/ecryptfs/keystore.c
@@ -1449,6 +1449,12 @@ parse_tag_11_packet(unsigned char *data, unsigned char *contents,
 		rc = -EINVAL;
 		goto out;
 	}
+	if (unlikely((*tag_11_contents_size) > max_contents_bytes)) {
+		printk(KERN_ERR "Literal data section in tag 11 packet exceeds "
+		       "expected size\n");
+		rc = -EINVAL;
+		goto out;
+	}
 	if (data[(*packet_size)++] != 0x62) {
 		printk(KERN_WARNING "Unrecognizable packet\n");
 		rc = -EINVAL;
-- 
GitLab


From f151cd2c54ddc7714e2f740681350476cda03a28 Mon Sep 17 00:00:00 2001
From: Ramon de Carvalho Valle <ramon@risesecurity.org>
Date: Tue, 28 Jul 2009 13:58:22 -0500
Subject: [PATCH 0159/1153] eCryptfs: parse_tag_3_packet check tag 3 packet
 encrypted key size

The parse_tag_3_packet function does not check if the tag 3 packet contains a
encrypted key size larger than ECRYPTFS_MAX_ENCRYPTED_KEY_BYTES.

Signed-off-by: Ramon de Carvalho Valle <ramon@risesecurity.org>
[tyhicks@linux.vnet.ibm.com: Added printk newline and changed goto to out_free]
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Cc: stable@kernel.org (2.6.27 and 30)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/ecryptfs/keystore.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/fs/ecryptfs/keystore.c b/fs/ecryptfs/keystore.c
index 5414253d4c9..259525c9abb 100644
--- a/fs/ecryptfs/keystore.c
+++ b/fs/ecryptfs/keystore.c
@@ -1303,6 +1303,13 @@ parse_tag_3_packet(struct ecryptfs_crypt_stat *crypt_stat,
 	}
 	(*new_auth_tok)->session_key.encrypted_key_size =
 		(body_size - (ECRYPTFS_SALT_SIZE + 5));
+	if ((*new_auth_tok)->session_key.encrypted_key_size
+	    > ECRYPTFS_MAX_ENCRYPTED_KEY_BYTES) {
+		printk(KERN_WARNING "Tag 3 packet contains key larger "
+		       "than ECRYPTFS_MAX_ENCRYPTED_KEY_BYTES\n");
+		rc = -EINVAL;
+		goto out_free;
+	}
 	if (unlikely(data[(*packet_size)++] != 0x04)) {
 		printk(KERN_WARNING "Unknown version number [%d]\n",
 		       data[(*packet_size) - 1]);
-- 
GitLab


From ce4adcc6e5320062e0d993eb75152d165aaabbe6 Mon Sep 17 00:00:00 2001
From: Andreas Eversberg <andreas@eversberg.eu>
Date: Mon, 27 Jul 2009 19:24:04 +0200
Subject: [PATCH 0160/1153] mISDN: Fix handling of receive buffer size in L1oIP

The size of receive buffer pointer was used to get size of
receive buffer instead of recvbuf_size itself, so only 4/8
bytes could be transfered.

This is a regression to 2.6.30 introduced by commit
8c90e11e3543d7de612194a042a148caeaab5f1d ("mISDN: Use
kernel_{send,recv}msg instead of open coding")

Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/isdn/mISDN/l1oip_core.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/isdn/mISDN/l1oip_core.c b/drivers/isdn/mISDN/l1oip_core.c
index 990e6a7e667..c3b661a666c 100644
--- a/drivers/isdn/mISDN/l1oip_core.c
+++ b/drivers/isdn/mISDN/l1oip_core.c
@@ -731,10 +731,10 @@ l1oip_socket_thread(void *data)
 	while (!signal_pending(current)) {
 		struct kvec iov = {
 			.iov_base = recvbuf,
-			.iov_len = sizeof(recvbuf),
+			.iov_len = recvbuf_size,
 		};
 		recvlen = kernel_recvmsg(socket, &msg, &iov, 1,
-					 sizeof(recvbuf), 0);
+					 recvbuf_size, 0);
 		if (recvlen > 0) {
 			l1oip_socket_parse(hc, &sin_rx, recvbuf, recvlen);
 		} else {
-- 
GitLab


From f99aa3f9b67ca8c29dc29ef3fc453f0343206c46 Mon Sep 17 00:00:00 2001
From: "Carlos R. Mafra" <crmafra@aei.mpg.de>
Date: Mon, 13 Jul 2009 21:45:03 +0200
Subject: [PATCH 0161/1153] USB: option: Remove unused variable

After commit f092c240494f2d807401d93f95f683909b90af96 ("USB: option:
remove unnecessary and erroneous code") the variable 'serial' becomes
unused, as gcc-4.3.2 points out:

drivers/usb/serial/option.c: In function 'option_instat_callback':
drivers/usb/serial/option.c:834: warning: unused variable 'serial'
drivers/usb/serial/option.c: In function 'option_open':
drivers/usb/serial/option.c:930: warning: unused variable 'serial'

So I removed it.

Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/option.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 98262dd552b..77b9563ec43 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -831,7 +831,6 @@ static void option_instat_callback(struct urb *urb)
 	int status = urb->status;
 	struct usb_serial_port *port =  urb->context;
 	struct option_port_private *portdata = usb_get_serial_port_data(port);
-	struct usb_serial *serial = port->serial;
 
 	dbg("%s", __func__);
 	dbg("%s: urb %p port %p has data %p", __func__, urb, port, portdata);
@@ -927,7 +926,6 @@ static int option_open(struct tty_struct *tty,
 			struct usb_serial_port *port, struct file *filp)
 {
 	struct option_port_private *portdata;
-	struct usb_serial *serial = port->serial;
 	int i, err;
 	struct urb *urb;
 
-- 
GitLab


From 5f4fab91f2b12c12f0506b4da49ed199db8c64ed Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Mon, 13 Jul 2009 23:24:10 +0200
Subject: [PATCH 0162/1153] USB: let the option driver compile without
 CONFIG_PM

This is needed for compilation without CONFIG_PM.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/option.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 77b9563ec43..7638d2632ff 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -66,8 +66,10 @@ static int  option_tiocmget(struct tty_struct *tty, struct file *file);
 static int  option_tiocmset(struct tty_struct *tty, struct file *file,
 				unsigned int set, unsigned int clear);
 static int  option_send_setup(struct usb_serial_port *port);
+#ifdef CONFIG_PM
 static int  option_suspend(struct usb_serial *serial, pm_message_t message);
 static int  option_resume(struct usb_serial *serial);
+#endif
 
 /* Vendor and product IDs */
 #define OPTION_VENDOR_ID			0x0AF0
@@ -555,8 +557,10 @@ static struct usb_driver option_driver = {
 	.name       = "option",
 	.probe      = usb_serial_probe,
 	.disconnect = usb_serial_disconnect,
+#ifdef CONFIG_PM
 	.suspend    = usb_serial_suspend,
 	.resume     = usb_serial_resume,
+#endif
 	.id_table   = option_ids,
 	.no_dynamic_id = 	1,
 };
@@ -588,8 +592,10 @@ static struct usb_serial_driver option_1port_device = {
 	.disconnect        = option_disconnect,
 	.release           = option_release,
 	.read_int_callback = option_instat_callback,
+#ifdef CONFIG_PM
 	.suspend           = option_suspend,
 	.resume            = option_resume,
+#endif
 };
 
 static int debug;
@@ -1185,6 +1191,7 @@ static void option_release(struct usb_serial *serial)
 	}
 }
 
+#ifdef CONFIG_PM
 static int option_suspend(struct usb_serial *serial, pm_message_t message)
 {
 	dbg("%s entered", __func__);
@@ -1243,6 +1250,7 @@ static int option_resume(struct usb_serial *serial)
 	}
 	return 0;
 }
+#endif
 
 MODULE_AUTHOR(DRIVER_AUTHOR);
 MODULE_DESCRIPTION(DRIVER_DESC);
-- 
GitLab


From 7a777919bbeec3eac1d7904a728a60e9c2bb9c67 Mon Sep 17 00:00:00 2001
From: Giacomo Lozito <james@develia.org>
Date: Mon, 13 Jul 2009 23:23:33 +0200
Subject: [PATCH 0163/1153] USB: storage: raise timeout in
 usb_stor_Bulk_max_lun

Requests to get max LUN, for certain USB storage devices, require a
longer timeout before a correct reply is returned. This happens for a
Realtek USB Card Reader (0bda:0152), which has a max LUN of 3 but is set
to 0, thus losing functionality, because of the timeout occurring too
quickly.

Raising the timeout value fixes the issue and might help other devices
to return a correct max LUN value as well.

Signed-off-by: Giacomo Lozito <james@develia.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/storage/transport.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c
index fcb32021721..e20dc525d17 100644
--- a/drivers/usb/storage/transport.c
+++ b/drivers/usb/storage/transport.c
@@ -961,7 +961,7 @@ int usb_stor_Bulk_max_lun(struct us_data *us)
 				 US_BULK_GET_MAX_LUN, 
 				 USB_DIR_IN | USB_TYPE_CLASS | 
 				 USB_RECIP_INTERFACE,
-				 0, us->ifnum, us->iobuf, 1, HZ);
+				 0, us->ifnum, us->iobuf, 1, 10*HZ);
 
 	US_DEBUGP("GetMaxLUN command result is %d, data is %d\n", 
 		  result, us->iobuf[0]);
-- 
GitLab


From 715bfc22ce952a14fac0b9200fd70d81c1951091 Mon Sep 17 00:00:00 2001
From: Anand Gadiyar <gadiyar@ti.com>
Date: Tue, 14 Jul 2009 16:41:00 +0530
Subject: [PATCH 0164/1153] USB: OMAP: OHCI: hc_driver's stop method should
 call ohci_stop

OMAP: OHCI: hc_driver's stop method should call ohci_stop

Without this, the ohci-omap driver will not cleanup the debugfs
nodes when the driver is unloaded. So the next insmod will fail,
if CONFIG_DEBUG_FS and CONFIG_USB_DEBUG are both selected.

Reported-by: vikram pandita <vikram.pandita@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/ohci-omap.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index f3aaba35e91..83cbecd2a1e 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -282,6 +282,7 @@ static int ohci_omap_init(struct usb_hcd *hcd)
 static void ohci_omap_stop(struct usb_hcd *hcd)
 {
 	dev_dbg(hcd->self.controller, "stopping USB Controller\n");
+	ohci_stop(hcd);
 	omap_ohci_clock_power(0);
 }
 
-- 
GitLab


From fca4404c55ab44c7413769f1d9c66451103711a5 Mon Sep 17 00:00:00 2001
From: Ville Sundberg <vsundber@gmail.com>
Date: Wed, 15 Jul 2009 00:27:28 +0300
Subject: [PATCH 0165/1153] USB: ftdi_sio: Add support for GN Otometrics
 Aurical USB Audiometer

The patch adds support for the GN Otometrics Aurical USB Audiometer
(FT232BM-based).
A new VID and a new PID is added.

Signed-off-by: Ville Sundberg <vsundber@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/ftdi_sio.c | 1 +
 drivers/usb/serial/ftdi_sio.h | 7 +++++++
 2 files changed, 8 insertions(+)

diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 60c64cc5be2..b574878c78b 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -698,6 +698,7 @@ static struct usb_device_id id_table_combined [] = {
 	{ USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID),
 		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
 	{ USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) },
+	{ USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) },
 	{ },					/* Optional parameter entry */
 	{ }					/* Terminating entry */
 };
diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h
index c9fbd741509..24dbd99e87d 100644
--- a/drivers/usb/serial/ftdi_sio.h
+++ b/drivers/usb/serial/ftdi_sio.h
@@ -946,6 +946,13 @@
 
 #define FTDI_TURTELIZER_PID	0xBDC8 /* JTAG/RS-232 adapter by egnite GmBH */
 
+/*
+ * GN Otometrics (http://www.otometrics.com)
+ * Submitted by Ville Sundberg.
+ */
+#define GN_OTOMETRICS_VID	0x0c33	/* Vendor ID */
+#define AURICAL_USB_PID		0x0010	/* Aurical USB Audiometer */
+
 /*
  *   BmRequestType:  1100 0000b
  *   bRequest:       FTDI_E2_READ
-- 
GitLab


From 8bf16ba7c8ea9d067914e270764c14020a26232f Mon Sep 17 00:00:00 2001
From: Craig Shelley <craig@microtron.org.uk>
Date: Sun, 12 Jul 2009 21:52:33 +0100
Subject: [PATCH 0166/1153] USB: CP210x Add new device IDs

Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/cp210x.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c
index e9a40b820fd..985cbcf48bd 100644
--- a/drivers/usb/serial/cp210x.c
+++ b/drivers/usb/serial/cp210x.c
@@ -80,6 +80,7 @@ static struct usb_device_id id_table [] = {
 	{ USB_DEVICE(0x10C4, 0x80F6) }, /* Suunto sports instrument */
 	{ USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */
 	{ USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */
+	{ USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */
 	{ USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */
 	{ USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */
 	{ USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */
@@ -96,7 +97,9 @@ static struct usb_device_id id_table [] = {
 	{ USB_DEVICE(0x10c4, 0x8293) }, /* Telegesys ETRX2USB */
 	{ USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */
 	{ USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */
+	{ USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */
 	{ USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */
+	{ USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */
 	{ USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */
 	{ USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
 	{ USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
-- 
GitLab


From bcfa4e68d8d0ea617bde4203b2b3848f5a49a423 Mon Sep 17 00:00:00 2001
From: Simon Kagstrom <simon.kagstrom@netinsight.net>
Date: Mon, 13 Jul 2009 08:25:09 +0200
Subject: [PATCH 0167/1153] USB: ehci-orion: Call ehci_reset before ehci_halt

I noticed that USB initialization didn't setup correctly on my kirkwood
based board (OpenRD base) if I hadn't initialized USB in U-boot first.
The error message looks like this:

  ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  orion-ehci orion-ehci.0: Marvell Orion EHCI
  orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
  orion-ehci orion-ehci.0: can't setup
  orion-ehci orion-ehci.0: USB bus 1 deregistered
  orion-ehci orion-ehci.0: init orion-ehci.0 fail, -110
  orion-ehci: probe of orion-ehci.0 failed with error -110

which is caused by ehci_halt() timing out in the handshake() call. I
noticed that U-boot does a reset before calling handshake(), so this
patch does the same thing for Linux. USB now works for me.

Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/ehci-orion.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/host/ehci-orion.c b/drivers/usb/host/ehci-orion.c
index dc2ac613a9d..1d283e1b2b8 100644
--- a/drivers/usb/host/ehci-orion.c
+++ b/drivers/usb/host/ehci-orion.c
@@ -105,6 +105,7 @@ static int ehci_orion_setup(struct usb_hcd *hcd)
 	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
 	int retval;
 
+	ehci_reset(ehci);
 	retval = ehci_halt(ehci);
 	if (retval)
 		return retval;
@@ -118,7 +119,6 @@ static int ehci_orion_setup(struct usb_hcd *hcd)
 
 	hcd->has_tt = 1;
 
-	ehci_reset(ehci);
 	ehci_port_power(ehci, 0);
 
 	return retval;
-- 
GitLab


From c420befde6b2747ebc2b8f015687a5dbd6e167ca Mon Sep 17 00:00:00 2001
From: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Date: Wed, 15 Jul 2009 17:10:26 -0300
Subject: [PATCH 0168/1153] USB: option: add ZTE device ids and remove ONDA ids

Current listed Onda ids are ZTE devices. Replace them with ZTE id define
and add more ZTE device ids. Also remove 19d2:2000, this is the id when
device is first plugged in and is a CD-only device, before the switch
using eject.

These changes are based on a previous patch by Ming Zhao
<zhao.ming9@zte.com.cn>

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Ming Zhao <zhao.ming9@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/option.c | 113 ++++++++++++++++++++++--------------
 1 file changed, 68 insertions(+), 45 deletions(-)

diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 7638d2632ff..5640f38fdb3 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -261,11 +261,6 @@ static int  option_resume(struct usb_serial *serial);
 #define AXESSTEL_VENDOR_ID			0x1726
 #define AXESSTEL_PRODUCT_MV110H			0x1000
 
-#define ONDA_VENDOR_ID				0x19d2
-#define ONDA_PRODUCT_MSA501HS			0x0001
-#define ONDA_PRODUCT_ET502HS			0x0002
-#define ONDA_PRODUCT_MT503HS			0x2000
-
 #define BANDRICH_VENDOR_ID			0x1A8D
 #define BANDRICH_PRODUCT_C100_1			0x1002
 #define BANDRICH_PRODUCT_C100_2			0x1003
@@ -476,42 +471,6 @@ static struct usb_device_id option_ids[] = {
 	{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_500A) },
 	{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ADU_620UW) },
 	{ USB_DEVICE(AXESSTEL_VENDOR_ID, AXESSTEL_PRODUCT_MV110H) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_MSA501HS) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_ET502HS) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0003) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0004) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0005) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0006) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0007) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0008) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0009) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x000a) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x000b) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x000c) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x000d) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x000e) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x000f) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0010) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0011) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0012) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0013) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0014) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0015) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0016) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0017) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0018) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0019) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0020) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0021) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0022) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0023) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0024) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0025) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0026) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0027) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0028) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, 0x0029) },
-	{ USB_DEVICE(ONDA_VENDOR_ID, ONDA_PRODUCT_MT503HS) },
 	{ USB_DEVICE(YISO_VENDOR_ID, YISO_PRODUCT_U893) },
 	{ USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_1) },
 	{ USB_DEVICE(BANDRICH_VENDOR_ID, BANDRICH_PRODUCT_C100_2) },
@@ -536,10 +495,74 @@ static struct usb_device_id option_ids[] = {
 	{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */
 	{ USB_DEVICE(MAXON_VENDOR_ID, 0x6280) }, /* BP3-USB & BP3-EXT HSDPA */
 	{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_UC864E) },
-	{ USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF622) },
-	{ USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF626) },
-	{ USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_MF628) },
-	{ USB_DEVICE(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF622, 0xff, 0xff, 0xff) }, /* ZTE WCDMA products */
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0002, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0003, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0004, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0005, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0006, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0007, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0008, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0009, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000a, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000b, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000c, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000d, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000e, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x000f, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0010, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0011, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0012, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0013, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF628, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0016, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0017, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0018, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0019, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0020, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0021, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0022, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0023, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0024, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0025, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0026, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0028, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0029, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0030, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF626, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0032, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0033, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0037, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0039, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0042, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0043, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0048, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0049, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0051, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0052, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0054, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0055, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0057, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0058, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0061, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0062, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0063, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0064, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0066, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0069, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0076, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0078, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0082, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0086, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x2002, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x2003, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0014, 0xff, 0xff, 0xff) }, /* ZTE CDMA products */
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0027, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0059, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0060, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0070, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0073, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) },
 	{ USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) },
 	{ USB_DEVICE(QISDA_VENDOR_ID, QISDA_PRODUCT_H21_4512) },
-- 
GitLab


From f1469fc3ef1d5a8a67146c1c72021f012a59dea6 Mon Sep 17 00:00:00 2001
From: Tim Gardner <tim.gardner@canonical.com>
Date: Fri, 17 Jul 2009 07:55:36 -0600
Subject: [PATCH 0169/1153] USB: option: Add USB ID for Novatel
 MC727/U727/USB727 refresh

BugLink: https://bugs.launchpad.net/bugs/365291

Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/option.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 5640f38fdb3..ff61f89918e 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -207,6 +207,7 @@ static int  option_resume(struct usb_serial *serial);
 #define NOVATELWIRELESS_PRODUCT_MC727		0x4100
 #define NOVATELWIRELESS_PRODUCT_MC950D		0x4400
 #define NOVATELWIRELESS_PRODUCT_U727		0x5010
+#define NOVATELWIRELESS_PRODUCT_MC727_NEW	0x5100
 #define NOVATELWIRELESS_PRODUCT_MC760		0x6000
 #define NOVATELWIRELESS_PRODUCT_OVMC760		0x6002
 
@@ -435,6 +436,7 @@ static struct usb_device_id option_ids[] = {
 	{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_EU870D) }, /* Novatel EU850D/EU860D/EU870D */
 	{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC950D) }, /* Novatel MC930D/MC950D */
 	{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC727) }, /* Novatel MC727/U727/USB727 */
+	{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC727_NEW) }, /* Novatel MC727/U727/USB727 refresh */
 	{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_U727) }, /* Novatel MC727/U727/USB727 */
 	{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_MC760) }, /* Novatel MC760/U760/USB760 */
 	{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_OVMC760) }, /* Novatel Ovation MC760 */
-- 
GitLab


From 9d498beafc0a66ce333f0d9067af0aa5dedd4c8e Mon Sep 17 00:00:00 2001
From: Russell Lang <gsview@ghostgum.com.au>
Date: Fri, 17 Jul 2009 19:29:20 +1000
Subject: [PATCH 0170/1153] USB: aten uc2324 is really a moschip 7840

I've opened up the case, and the chips in the ATEN UC2324 are:

Moschip
MCS7840CV-AA
69507-6B1
0650
(USB to 4-port serial)

(logo with AF kerned together)  0748
24BC02
SINGLP
(unknown 8-pin chip)

(logo looks like 3 or Z in circle)
ZT3243LEEA    0752
B7A16420.T
(4 chips, so this will be RS232 line driver)
(Probably equivalent of Sipex SP3243)

So the ATEN 2324 (aten2011.c driver), is definitely the Moschip 7840,
and should use the mos7840.c driver.  I expect you will remove the
aten2011.c driver from the staging area.

From the aten2011.c source code, the device ID for the UC2322 (2 port
serial) is 0x7820, just like the Moschip evaluation board.  This value
should be added to the device id table of mos7840.c.

Here's a patch that adds these devices to the driver.


From: Russell Lang <gsview@ghostgum.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/mos7840.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c
index c31940a307f..270009afdf7 100644
--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -124,10 +124,13 @@
 #define BANDB_DEVICE_ID_USOPTL4_4       0xAC44
 #define BANDB_DEVICE_ID_USOPTL4_2       0xAC42
 
-/* This driver also supports the ATEN UC2324 device since it is mos7840 based
- *  - if I knew the device id it would also support the ATEN UC2322 */
+/* This driver also supports
+ * ATEN UC2324 device using Moschip MCS7840
+ * ATEN UC2322 device using Moschip MCS7820
+ */
 #define USB_VENDOR_ID_ATENINTL		0x0557
 #define ATENINTL_DEVICE_ID_UC2324	0x2011
+#define ATENINTL_DEVICE_ID_UC2322	0x7820
 
 /* Interrupt Routine Defines    */
 
@@ -177,6 +180,7 @@ static struct usb_device_id moschip_port_id_table[] = {
 	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)},
 	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)},
 	{USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)},
+	{USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2322)},
 	{}			/* terminating entry */
 };
 
@@ -186,6 +190,7 @@ static __devinitdata struct usb_device_id moschip_id_table_combined[] = {
 	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)},
 	{USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)},
 	{USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)},
+	{USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2322)},
 	{}			/* terminating entry */
 };
 
-- 
GitLab


From 183791588efd416fc35a71819683b32dee92615b Mon Sep 17 00:00:00 2001
From: Peng Huang <shawn.p.huang@gmail.com>
Date: Wed, 22 Jul 2009 11:54:48 +0200
Subject: [PATCH 0171/1153] USB: serial: option: Add ZTE AC8710 usb modem
 device.

Signed-off-by: Peng Huang <shawn.p.huang@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/option.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index ff61f89918e..b6de085bc78 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -299,6 +299,7 @@ static int  option_resume(struct usb_serial *serial);
 #define ZTE_PRODUCT_MF628			0x0015
 #define ZTE_PRODUCT_MF626			0x0031
 #define ZTE_PRODUCT_CDMA_TECH			0xfffe
+#define ZTE_PRODUCT_AC8710			0xfff1
 
 #define BENQ_VENDOR_ID				0x04a5
 #define BENQ_PRODUCT_H10			0x4068
@@ -565,6 +566,7 @@ static struct usb_device_id option_ids[] = {
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0070, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0073, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_CDMA_TECH, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_AC8710, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) },
 	{ USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) },
 	{ USB_DEVICE(QISDA_VENDOR_ID, QISDA_PRODUCT_H21_4512) },
-- 
GitLab


From 48c348cc939aaa3a07d4938669f2f315152e895e Mon Sep 17 00:00:00 2001
From: Javier Martin <jmartinj@iname.com>
Date: Thu, 23 Jul 2009 04:03:43 +0200
Subject: [PATCH 0172/1153] USB: option.c to support Alcatel X060S/X200
 broadband modems

Added support for the Alcatel X060S/X200 broadband modems to the option
driver. The device starts in cd-rom emulation mode (1bbb:f000) and
requires the use of the usb_modeswitch tool to switch it to modem mode
(1bbb:0000).

Signed-off-by: Javier Martin <jmartinj@iname.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/option.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index b6de085bc78..c784ddbe7b6 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -321,6 +321,11 @@ static int  option_resume(struct usb_serial *serial);
 #define ALINK_VENDOR_ID				0x1e0e
 #define ALINK_PRODUCT_3GU			0x9200
 
+/* ALCATEL PRODUCTS */
+#define ALCATEL_VENDOR_ID			0x1bbb
+#define ALCATEL_PRODUCT_X060S			0x0000
+
+
 static struct usb_device_id option_ids[] = {
 	{ USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COLT) },
 	{ USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_RICOLA) },
@@ -576,6 +581,7 @@ static struct usb_device_id option_ids[] = {
 	{ USB_DEVICE(TOSHIBA_VENDOR_ID, TOSHIBA_PRODUCT_HSDPA_MINICARD ) }, /* Toshiba 3G HSDPA == Novatel Expedite EU870D MiniCard */
 	{ USB_DEVICE(ALINK_VENDOR_ID, 0x9000) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ALINK_VENDOR_ID, ALINK_PRODUCT_3GU, 0xff, 0xff, 0xff) },
+	{ USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_X060S) },
 	{ } /* Terminating entry */
 };
 MODULE_DEVICE_TABLE(usb, option_ids);
-- 
GitLab


From f01b017d198486ee3553bee6841f788263cf2c23 Mon Sep 17 00:00:00 2001
From: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Date: Fri, 17 Jul 2009 17:30:03 +0300
Subject: [PATCH 0173/1153] USB: musb_gadget_ep0: fix typo in
 service_zero_data_request()

This function uses wrong bit mask to prevent clearing RXCSR status
bits when halting an endpoint -- which results in clearing SentStall
and RxPktRdy bits (that the code actually tries to avoid); must be
a result of cut-and-paste...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/musb/musb_gadget_ep0.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/musb/musb_gadget_ep0.c b/drivers/usb/musb/musb_gadget_ep0.c
index 40ed50ecedf..7a6778675ad 100644
--- a/drivers/usb/musb/musb_gadget_ep0.c
+++ b/drivers/usb/musb/musb_gadget_ep0.c
@@ -407,7 +407,7 @@ stall:
 					csr |= MUSB_RXCSR_P_SENDSTALL
 						| MUSB_RXCSR_FLUSHFIFO
 						| MUSB_RXCSR_CLRDATATOG
-						| MUSB_TXCSR_P_WZC_BITS;
+						| MUSB_RXCSR_P_WZC_BITS;
 					musb_writew(regs, MUSB_RXCSR,
 							csr);
 				}
-- 
GitLab


From 3a9f5bd82dc986d496d8484ff54b107b4515f43f Mon Sep 17 00:00:00 2001
From: Amit Kucheria <amit.kucheria@canonical.com>
Date: Mon, 27 Jul 2009 12:03:19 +0300
Subject: [PATCH 0174/1153] USB: musb: Refer to musb_otg_timer_func under
 correct #ifdef

musb_otg_timer_func() is defined under #ifdef CONFIG_USB_MUSB_OTG.
Make sure any reference to it is also under the same #ifdef.

Without this fix, the driver failes to compile when USB_OTG is defined
but USB_MUSB_OTG isn't.

Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/musb/musb_core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index 554a414f65d..642a4e25f7d 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -1990,7 +1990,7 @@ bad_config:
 	if (status < 0)
 		goto fail2;
 
-#ifdef CONFIG_USB_OTG
+#ifdef CONFIG_USB_MUSB_OTG
 	setup_timer(&musb->otg_timer, musb_otg_timer_func, (unsigned long) musb);
 #endif
 
-- 
GitLab


From 2bbff7b742d55b094ed1467702efe146cd60c64f Mon Sep 17 00:00:00 2001
From: Ajay Kumar Gupta <ajay.gupta@ti.com>
Date: Mon, 27 Jul 2009 14:32:15 -0700
Subject: [PATCH 0175/1153] USB: musb: fix CONFIGDATA register read issue

INDEX register has to be set to '0' before reading
CONFIGDATA register which is only present in TI musb
platforms.

Currently the default register access mode is set to
FLAT_MODE thus INDEX register is not getting set
properly with musb_ep_select() which is just a nop
operation in FLAT_MODE.This invalid register read is
causing module reinset failure.

Fixing the issue by moving INDEX register write part to
musb_read_configdata() function itself.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/musb/musb_core.c | 1 -
 drivers/usb/musb/musb_regs.h | 1 +
 2 files changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index 642a4e25f7d..c7c1ca0494c 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -1326,7 +1326,6 @@ static int __init musb_core_init(u16 musb_type, struct musb *musb)
 	int		i;
 
 	/* log core options (read using indexed model) */
-	musb_ep_select(mbase, 0);
 	reg = musb_read_configdata(mbase);
 
 	strcpy(aInfo, (reg & MUSB_CONFIGDATA_UTMIDW) ? "UTMI-16" : "UTMI-8");
diff --git a/drivers/usb/musb/musb_regs.h b/drivers/usb/musb/musb_regs.h
index de3b2f18db4..fbfd3fd9ce1 100644
--- a/drivers/usb/musb/musb_regs.h
+++ b/drivers/usb/musb/musb_regs.h
@@ -323,6 +323,7 @@ static inline void  musb_write_rxfifoadd(void __iomem *mbase, u16 c_off)
 
 static inline u8 musb_read_configdata(void __iomem *mbase)
 {
+	musb_writeb(mbase, MUSB_INDEX, 0);
 	return musb_readb(mbase, 0x10 + MUSB_CONFIGDATA);
 }
 
-- 
GitLab


From 0f157ef3a1284f41d9804ecb87fdcc8ea946b9fa Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Tue, 28 Jul 2009 11:56:17 -0400
Subject: [PATCH 0176/1153] USB: usbtest: no need for USB_DEVICEFS

THis patch (as1270) allows the usbtest module to be built even when
USB_DEVICEFS isn't configured.  Tests can be performed without
USB_DEVICEFS, using the /dev/bus/usb/*/* device files.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/misc/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig
index a68d91a11be..abe3aa67ed0 100644
--- a/drivers/usb/misc/Kconfig
+++ b/drivers/usb/misc/Kconfig
@@ -220,7 +220,7 @@ config USB_IOWARRIOR
 
 config USB_TEST
 	tristate "USB testing driver"
-	depends on USB && USB_DEVICEFS
+	depends on USB
 	help
 	  This driver is for testing host controller software.  It is used
 	  with specialized device firmware for regression and stress testing,
-- 
GitLab


From d8f1a5ed52a81a953918d4aebe185ba008a7be34 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Mon, 13 Jul 2009 00:23:47 +0200
Subject: [PATCH 0177/1153] USB: xhci: fix less- and greater than confusion

Without this change the loops won't start

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-dbg.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c
index 2501c571f85..56032f2d84e 100644
--- a/drivers/usb/host/xhci-dbg.c
+++ b/drivers/usb/host/xhci-dbg.c
@@ -419,7 +419,7 @@ void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_ad
 			&ctx->add_flags, (unsigned long long)dma,
 			ctx->add_flags);
 	dma += field_size;
-	for (i = 0; i > 6; ++i) {
+	for (i = 0; i < 6; ++i) {
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
 				&ctx->rsvd[i], (unsigned long long)dma,
 				ctx->rsvd[i], i);
@@ -443,7 +443,7 @@ void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_ad
 			&ctx->slot.dev_state,
 			(unsigned long long)dma, ctx->slot.dev_state);
 	dma += field_size;
-	for (i = 0; i > 4; ++i) {
+	for (i = 0; i < 4; ++i) {
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
 				&ctx->slot.reserved[i], (unsigned long long)dma,
 				ctx->slot.reserved[i], i);
-- 
GitLab


From f9dc68fe7ad390428c6bc5d7ff582cdb5d92fcb8 Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:03:07 -0700
Subject: [PATCH 0178/1153] USB: xhci: Set TD size in transfer TRB.

The 0.95 xHCI specification requires software to set the "TD size" field
in each transaction request block (TRB).  This field gives the host
controller an indication of how much data is remaining in the TD
(including the buffer in the current TRB).  Set this field in bulk TRBs
and data stage TRBs for control transfers.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-ring.c | 20 +++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 02d81985c45..d5b95299742 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -1285,6 +1285,7 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	/* Queue the first TRB, even if it's zero-length */
 	do {
 		u32 field = 0;
+		u32 length_field = 0;
 
 		/* Don't change the cycle bit of the first TRB until later */
 		if (first_trb)
@@ -1314,10 +1315,13 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 					(unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1),
 					(unsigned int) addr + trb_buff_len);
 		}
+		length_field = TRB_LEN(trb_buff_len) |
+			TD_REMAINDER(urb->transfer_buffer_length - running_total) |
+			TRB_INTR_TARGET(0);
 		queue_trb(xhci, ep_ring, false,
 				(u32) addr,
 				(u32) ((u64) addr >> 32),
-				TRB_LEN(trb_buff_len) | TRB_INTR_TARGET(0),
+				length_field,
 				/* We always want to know if the TRB was short,
 				 * or we won't get an event when it completes.
 				 * (Unless we use event data TRBs, which are a
@@ -1365,7 +1369,7 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	struct xhci_generic_trb *start_trb;
 	bool first_trb;
 	int start_cycle;
-	u32 field;
+	u32 field, length_field;
 
 	int running_total, trb_buff_len, ret;
 	u64 addr;
@@ -1443,10 +1447,13 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 			td->last_trb = ep_ring->enqueue;
 			field |= TRB_IOC;
 		}
+		length_field = TRB_LEN(trb_buff_len) |
+			TD_REMAINDER(urb->transfer_buffer_length - running_total) |
+			TRB_INTR_TARGET(0);
 		queue_trb(xhci, ep_ring, false,
 				(u32) addr,
 				(u32) ((u64) addr >> 32),
-				TRB_LEN(trb_buff_len) | TRB_INTR_TARGET(0),
+				length_field,
 				/* We always want to know if the TRB was short,
 				 * or we won't get an event when it completes.
 				 * (Unless we use event data TRBs, which are a
@@ -1478,7 +1485,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 	struct usb_ctrlrequest *setup;
 	struct xhci_generic_trb *start_trb;
 	int start_cycle;
-	u32 field;
+	u32 field, length_field;
 	struct xhci_td *td;
 
 	ep_ring = xhci->devs[slot_id]->ep_rings[ep_index];
@@ -1528,13 +1535,16 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 
 	/* If there's data, queue data TRBs */
 	field = 0;
+	length_field = TRB_LEN(urb->transfer_buffer_length) |
+		TD_REMAINDER(urb->transfer_buffer_length) |
+		TRB_INTR_TARGET(0);
 	if (urb->transfer_buffer_length > 0) {
 		if (setup->bRequestType & USB_DIR_IN)
 			field |= TRB_DIR_IN;
 		queue_trb(xhci, ep_ring, false,
 				lower_32_bits(urb->transfer_dma),
 				upper_32_bits(urb->transfer_dma),
-				TRB_LEN(urb->transfer_buffer_length) | TRB_INTR_TARGET(0),
+				length_field,
 				/* Event on short tx */
 				field | TRB_ISP | TRB_TYPE(TRB_DATA) | ep_ring->cycle_state);
 	}
-- 
GitLab


From a1587d97ce3e53816c88b513a2038f6c5e5babd7 Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:03:15 -0700
Subject: [PATCH 0179/1153] USB: xhci: Deal with stalled endpoints.

When an endpoint on a device under an xHCI host controller stalls, the
host controller driver must let the hardware know that the USB core has
successfully cleared the halt condition.  The HCD submits a Reset Endpoint
Command, which will clear the toggle bit for USB 2.0 devices, and set the
sequence number to zero for USB 3.0 devices.

The xHCI urb_enqueue will accept new URBs while the endpoint is halted,
and will queue them to the hardware rings.  However, the endpoint doorbell
will not be rung until the Reset Endpoint Command completes.

Don't queue a reset endpoint command for root hubs.  khubd clears halt
conditions on the roothub during the initialization process, but the roothub
isn't a real device, so the xHCI host controller doesn't need to know about the
cleared halt.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-hcd.c  | 44 +++++++++++++++++++++++++++++++++++-
 drivers/usb/host/xhci-pci.c  |  1 +
 drivers/usb/host/xhci-ring.c | 36 ++++++++++++++++++++++++++++-
 drivers/usb/host/xhci.h      |  8 +++++--
 4 files changed, 85 insertions(+), 4 deletions(-)

diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c
index dba3e07ccd0..1c5901ad6eb 100644
--- a/drivers/usb/host/xhci-hcd.c
+++ b/drivers/usb/host/xhci-hcd.c
@@ -787,8 +787,11 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 	int ret = 0;
 
 	ret = xhci_check_args(hcd, udev, ep, 1, __func__);
-	if (ret <= 0)
+	if (ret <= 0) {
+		/* So we won't queue a reset ep command for a root hub */
+		ep->hcpriv = NULL;
 		return ret;
+	}
 	xhci = hcd_to_xhci(hcd);
 
 	added_ctxs = xhci_get_endpoint_flag(&ep->desc);
@@ -851,6 +854,9 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 	}
 	new_slot_info = in_ctx->slot.dev_info;
 
+	/* Store the usb_device pointer for later use */
+	ep->hcpriv = udev;
+
 	xhci_dbg(xhci, "add ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x, new slot info = %#x\n",
 			(unsigned int) ep->desc.bEndpointAddress,
 			udev->slot_id,
@@ -1026,6 +1032,42 @@ void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	xhci_zero_in_ctx(virt_dev);
 }
 
+/* Deal with stalled endpoints.  The core should have sent the control message
+ * to clear the halt condition.  However, we need to make the xHCI hardware
+ * reset its sequence number, since a device will expect a sequence number of
+ * zero after the halt condition is cleared.
+ * Context: in_interrupt
+ */
+void xhci_endpoint_reset(struct usb_hcd *hcd,
+		struct usb_host_endpoint *ep)
+{
+	struct xhci_hcd *xhci;
+	struct usb_device *udev;
+	unsigned int ep_index;
+	unsigned long flags;
+	int ret;
+
+	xhci = hcd_to_xhci(hcd);
+	udev = (struct usb_device *) ep->hcpriv;
+	/* Called with a root hub endpoint (or an endpoint that wasn't added
+	 * with xhci_add_endpoint()
+	 */
+	if (!ep->hcpriv)
+		return;
+	ep_index = xhci_get_endpoint_index(&ep->desc);
+
+	xhci_dbg(xhci, "Queueing reset endpoint command\n");
+	spin_lock_irqsave(&xhci->lock, flags);
+	ret = xhci_queue_reset_ep(xhci, udev->slot_id, ep_index);
+	if (!ret) {
+		xhci_ring_cmd_db(xhci);
+	}
+	spin_unlock_irqrestore(&xhci->lock, flags);
+
+	if (ret)
+		xhci_warn(xhci, "FIXME allocate a new ring segment\n");
+}
+
 /*
  * At this point, the struct usb_device is about to go away, the device has
  * disconnected, and all traffic has been stopped and the endpoints have been
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index 1462709e26c..592fe7e623f 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -117,6 +117,7 @@ static const struct hc_driver xhci_pci_hc_driver = {
 	.free_dev =		xhci_free_dev,
 	.add_endpoint =		xhci_add_endpoint,
 	.drop_endpoint =	xhci_drop_endpoint,
+	.endpoint_reset =	xhci_endpoint_reset,
 	.check_bandwidth =	xhci_check_bandwidth,
 	.reset_bandwidth =	xhci_reset_bandwidth,
 	.address_device =	xhci_address_device,
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index d5b95299742..d672ba14ff8 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -279,7 +279,8 @@ static void ring_ep_doorbell(struct xhci_hcd *xhci,
 	/* Don't ring the doorbell for this endpoint if there are pending
 	 * cancellations because the we don't want to interrupt processing.
 	 */
-	if (!ep_ring->cancels_pending && !(ep_ring->state & SET_DEQ_PENDING)) {
+	if (!ep_ring->cancels_pending && !(ep_ring->state & SET_DEQ_PENDING)
+			&& !(ep_ring->state & EP_HALTED)) {
 		field = xhci_readl(xhci, db_addr) & DB_MASK;
 		xhci_writel(xhci, field | EPI_TO_DB(ep_index), db_addr);
 		/* Flush PCI posted writes - FIXME Matthew Wilcox says this
@@ -603,6 +604,25 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci,
 	ring_ep_doorbell(xhci, slot_id, ep_index);
 }
 
+static void handle_reset_ep_completion(struct xhci_hcd *xhci,
+		struct xhci_event_cmd *event,
+		union xhci_trb *trb)
+{
+	int slot_id;
+	unsigned int ep_index;
+
+	slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]);
+	ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]);
+	/* This command will only fail if the endpoint wasn't halted,
+	 * but we don't care.
+	 */
+	xhci_dbg(xhci, "Ignoring reset ep completion code of %u\n",
+			(unsigned int) GET_COMP_CODE(event->status));
+
+	/* Clear our internal halted state and restart the ring */
+	xhci->devs[slot_id]->ep_rings[ep_index]->state &= ~EP_HALTED;
+	ring_ep_doorbell(xhci, slot_id, ep_index);
+}
 
 static void handle_cmd_completion(struct xhci_hcd *xhci,
 		struct xhci_event_cmd *event)
@@ -653,6 +673,9 @@ static void handle_cmd_completion(struct xhci_hcd *xhci,
 	case TRB_TYPE(TRB_CMD_NOOP):
 		++xhci->noops_handled;
 		break;
+	case TRB_TYPE(TRB_RESET_EP):
+		handle_reset_ep_completion(xhci, event, xhci->cmd_ring->dequeue);
+		break;
 	default:
 		/* Skip over unknown commands on the event ring */
 		xhci->error_bitmask |= 1 << 6;
@@ -823,6 +846,7 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 		break;
 	case COMP_STALL:
 		xhci_warn(xhci, "WARN: Stalled endpoint\n");
+		ep_ring->state |= EP_HALTED;
 		status = -EPIPE;
 		break;
 	case COMP_TRB_ERR:
@@ -1656,3 +1680,13 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id,
 	return queue_command(xhci, (u32) addr | cycle_state, 0, 0,
 			trb_slot_id | trb_ep_index | type);
 }
+
+int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id,
+		unsigned int ep_index)
+{
+	u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id);
+	u32 trb_ep_index = EP_ID_FOR_TRB(ep_index);
+	u32 type = TRB_TYPE(TRB_RESET_EP);
+
+	return queue_command(xhci, 0, 0, 0, trb_slot_id | trb_ep_index | type);
+}
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 8936eeb5588..cde648a524f 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -848,8 +848,8 @@ union xhci_trb {
 #define TRB_CONFIG_EP		12
 /* Evaluate Context Command */
 #define TRB_EVAL_CONTEXT	13
-/* Reset Transfer Ring Command */
-#define TRB_RESET_RING		14
+/* Reset Endpoint Command */
+#define TRB_RESET_EP		14
 /* Stop Transfer Ring Command */
 #define TRB_STOP_RING		15
 /* Set Transfer Ring Dequeue Pointer Command */
@@ -929,6 +929,7 @@ struct xhci_ring {
 	unsigned int		cancels_pending;
 	unsigned int		state;
 #define SET_DEQ_PENDING		(1 << 0)
+#define EP_HALTED		(1 << 1)
 	/* The TRB that was last reported in a stopped endpoint ring */
 	union xhci_trb		*stopped_trb;
 	struct xhci_td		*stopped_td;
@@ -1128,6 +1129,7 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags);
 int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status);
 int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep);
 int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep);
+void xhci_endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep);
 int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 
@@ -1148,6 +1150,8 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, struct urb *urb,
 		int slot_id, unsigned int ep_index);
 int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
 		u32 slot_id);
+int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id,
+		unsigned int ep_index);
 
 /* xHCI roothub code */
 int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex,
-- 
GitLab


From b11069f5f6ce6e359f853e908b0917303fcdec8f Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:03:23 -0700
Subject: [PATCH 0180/1153] USB: xhci: Use GFP_ATOMIC while holding spinlocks.

The xHCI functions to queue an URB onto the hardware rings must be called
with the xhci spinlock held.  Those functions will allocate memory, and
take a gfp_t memory flags argument.  We must pass them the GFP_ATOMIC
flag, since we don't want the memory allocation to attempt to sleep while
waiting for more memory to become available.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-hcd.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c
index 1c5901ad6eb..ff99365cae4 100644
--- a/drivers/usb/host/xhci-hcd.c
+++ b/drivers/usb/host/xhci-hcd.c
@@ -601,10 +601,13 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags)
 		goto exit;
 	}
 	if (usb_endpoint_xfer_control(&urb->ep->desc))
-		ret = xhci_queue_ctrl_tx(xhci, mem_flags, urb,
+		/* We have a spinlock and interrupts disabled, so we must pass
+		 * atomic context to this function, which may allocate memory.
+		 */
+		ret = xhci_queue_ctrl_tx(xhci, GFP_ATOMIC, urb,
 				slot_id, ep_index);
 	else if (usb_endpoint_xfer_bulk(&urb->ep->desc))
-		ret = xhci_queue_bulk_tx(xhci, mem_flags, urb,
+		ret = xhci_queue_bulk_tx(xhci, GFP_ATOMIC, urb,
 				slot_id, ep_index);
 	else
 		ret = -EINVAL;
-- 
GitLab


From 8e595a5d30a5ee4bb745d4da6439d73ed7d91054 Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:03:31 -0700
Subject: [PATCH 0181/1153] USB: xhci: Represent 64-bit addresses with one u64.

There are several xHCI data structures that use two 32-bit fields to
represent a 64-bit address.  Since some architectures don't support 64-bit
PCI writes, the fields need to be written in two 32-bit writes.  The xHCI
specification says that if a platform is incapable of generating 64-bit
writes, software must write the low 32-bits first, then the high 32-bits.
Hardware that supports 64-bit addressing will wait for the high 32-bit
write before reading the revised value, and hardware that only supports
32-bit writes will ignore the high 32-bit write.

Previous xHCI code represented 64-bit addresses with two u32 values.  This
lead to buggy code that would write the 32-bits in the wrong order, or
forget to write the upper 32-bits.  Change the two u32s to one u64 and
create a function call to write all 64-bit addresses in the proper order.
This new function could be modified in the future if all platforms support
64-bit writes.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-dbg.c  | 67 ++++++++++++++----------------------
 drivers/usb/host/xhci-hcd.c  | 43 ++++++++++-------------
 drivers/usb/host/xhci-mem.c  | 61 +++++++++++++-------------------
 drivers/usb/host/xhci-ring.c | 49 +++++++++++++-------------
 drivers/usb/host/xhci.h      | 65 +++++++++++++++++++++++-----------
 5 files changed, 137 insertions(+), 148 deletions(-)

diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c
index 56032f2d84e..6d62e4abe3c 100644
--- a/drivers/usb/host/xhci-dbg.c
+++ b/drivers/usb/host/xhci-dbg.c
@@ -173,6 +173,7 @@ void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int
 {
 	void *addr;
 	u32 temp;
+	u64 temp_64;
 
 	addr = &ir_set->irq_pending;
 	temp = xhci_readl(xhci, addr);
@@ -200,25 +201,15 @@ void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int
 		xhci_dbg(xhci, "  WARN: %p: ir_set.rsvd = 0x%x\n",
 				addr, (unsigned int)temp);
 
-	addr = &ir_set->erst_base[0];
-	temp = xhci_readl(xhci, addr);
-	xhci_dbg(xhci, "  %p: ir_set.erst_base[0] = 0x%x\n",
-			addr, (unsigned int) temp);
-
-	addr = &ir_set->erst_base[1];
-	temp = xhci_readl(xhci, addr);
-	xhci_dbg(xhci, "  %p: ir_set.erst_base[1] = 0x%x\n",
-			addr, (unsigned int) temp);
-
-	addr = &ir_set->erst_dequeue[0];
-	temp = xhci_readl(xhci, addr);
-	xhci_dbg(xhci, "  %p: ir_set.erst_dequeue[0] = 0x%x\n",
-			addr, (unsigned int) temp);
+	addr = &ir_set->erst_base;
+	temp_64 = xhci_read_64(xhci, addr);
+	xhci_dbg(xhci, "  %p: ir_set.erst_base = @%08llx\n",
+			addr, temp_64);
 
-	addr = &ir_set->erst_dequeue[1];
-	temp = xhci_readl(xhci, addr);
-	xhci_dbg(xhci, "  %p: ir_set.erst_dequeue[1] = 0x%x\n",
-			addr, (unsigned int) temp);
+	addr = &ir_set->erst_dequeue;
+	temp_64 = xhci_read_64(xhci, addr);
+	xhci_dbg(xhci, "  %p: ir_set.erst_dequeue = @%08llx\n",
+			addr, temp_64);
 }
 
 void xhci_print_run_regs(struct xhci_hcd *xhci)
@@ -268,8 +259,7 @@ void xhci_debug_trb(struct xhci_hcd *xhci, union xhci_trb *trb)
 		xhci_dbg(xhci, "Link TRB:\n");
 		xhci_print_trb_offsets(xhci, trb);
 
-		address = trb->link.segment_ptr[0] +
-			(((u64) trb->link.segment_ptr[1]) << 32);
+		address = trb->link.segment_ptr;
 		xhci_dbg(xhci, "Next ring segment DMA address = 0x%llx\n", address);
 
 		xhci_dbg(xhci, "Interrupter target = 0x%x\n",
@@ -282,8 +272,7 @@ void xhci_debug_trb(struct xhci_hcd *xhci, union xhci_trb *trb)
 				(unsigned int) (trb->link.control & TRB_NO_SNOOP));
 		break;
 	case TRB_TYPE(TRB_TRANSFER):
-		address = trb->trans_event.buffer[0] +
-			(((u64) trb->trans_event.buffer[1]) << 32);
+		address = trb->trans_event.buffer;
 		/*
 		 * FIXME: look at flags to figure out if it's an address or if
 		 * the data is directly in the buffer field.
@@ -291,8 +280,7 @@ void xhci_debug_trb(struct xhci_hcd *xhci, union xhci_trb *trb)
 		xhci_dbg(xhci, "DMA address or buffer contents= %llu\n", address);
 		break;
 	case TRB_TYPE(TRB_COMPLETION):
-		address = trb->event_cmd.cmd_trb[0] +
-			(((u64) trb->event_cmd.cmd_trb[1]) << 32);
+		address = trb->event_cmd.cmd_trb;
 		xhci_dbg(xhci, "Command TRB pointer = %llu\n", address);
 		xhci_dbg(xhci, "Completion status = %u\n",
 				(unsigned int) GET_COMP_CODE(trb->event_cmd.status));
@@ -328,8 +316,8 @@ void xhci_debug_segment(struct xhci_hcd *xhci, struct xhci_segment *seg)
 	for (i = 0; i < TRBS_PER_SEGMENT; ++i) {
 		trb = &seg->trbs[i];
 		xhci_dbg(xhci, "@%08x %08x %08x %08x %08x\n", addr,
-				(unsigned int) trb->link.segment_ptr[0],
-				(unsigned int) trb->link.segment_ptr[1],
+				lower_32_bits(trb->link.segment_ptr),
+				upper_32_bits(trb->link.segment_ptr),
 				(unsigned int) trb->link.intr_target,
 				(unsigned int) trb->link.control);
 		addr += sizeof(*trb);
@@ -386,8 +374,8 @@ void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst)
 		entry = &erst->entries[i];
 		xhci_dbg(xhci, "@%08x %08x %08x %08x %08x\n",
 				(unsigned int) addr,
-				(unsigned int) entry->seg_addr[0],
-				(unsigned int) entry->seg_addr[1],
+				lower_32_bits(entry->seg_addr),
+				upper_32_bits(entry->seg_addr),
 				(unsigned int) entry->seg_size,
 				(unsigned int) entry->rsvd);
 		addr += sizeof(*entry);
@@ -396,12 +384,13 @@ void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst)
 
 void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci)
 {
-	u32 val;
+	u64 val;
 
-	val = xhci_readl(xhci, &xhci->op_regs->cmd_ring[0]);
-	xhci_dbg(xhci, "// xHC command ring deq ptr low bits + flags = 0x%x\n", val);
-	val = xhci_readl(xhci, &xhci->op_regs->cmd_ring[1]);
-	xhci_dbg(xhci, "// xHC command ring deq ptr high bits = 0x%x\n", val);
+	val = xhci_read_64(xhci, &xhci->op_regs->cmd_ring);
+	xhci_dbg(xhci, "// xHC command ring deq ptr low bits + flags = @%08x\n",
+			lower_32_bits(val));
+	xhci_dbg(xhci, "// xHC command ring deq ptr high bits = @%08x\n",
+			upper_32_bits(val));
 }
 
 void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep)
@@ -462,14 +451,10 @@ void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_ad
 				&ctx->ep[i].ep_info2,
 				(unsigned long long)dma, ctx->ep[i].ep_info2);
 		dma += field_size;
-		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - deq[0]\n",
-				&ctx->ep[i].deq[0],
-				(unsigned long long)dma, ctx->ep[i].deq[0]);
-		dma += field_size;
-		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - deq[1]\n",
-				&ctx->ep[i].deq[1],
-				(unsigned long long)dma, ctx->ep[i].deq[1]);
-		dma += field_size;
+		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08llx - deq\n",
+				&ctx->ep[i].deq,
+				(unsigned long long)dma, ctx->ep[i].deq);
+		dma += 2*field_size;
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tx_info\n",
 				&ctx->ep[i].tx_info,
 				(unsigned long long)dma, ctx->ep[i].tx_info);
diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c
index ff99365cae4..e15773598e4 100644
--- a/drivers/usb/host/xhci-hcd.c
+++ b/drivers/usb/host/xhci-hcd.c
@@ -226,6 +226,7 @@ int xhci_init(struct usb_hcd *hcd)
 static void xhci_work(struct xhci_hcd *xhci)
 {
 	u32 temp;
+	u64 temp_64;
 
 	/*
 	 * Clear the op reg interrupt status first,
@@ -249,8 +250,8 @@ static void xhci_work(struct xhci_hcd *xhci)
 	xhci_handle_event(xhci);
 
 	/* Clear the event handler busy flag; the event ring should be empty. */
-	temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]);
-	xhci_writel(xhci, temp & ~ERST_EHB, &xhci->ir_set->erst_dequeue[0]);
+	temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
+	xhci_write_64(xhci, temp_64 & ~ERST_EHB, &xhci->ir_set->erst_dequeue);
 	/* Flush posted writes -- FIXME is this necessary? */
 	xhci_readl(xhci, &xhci->ir_set->irq_pending);
 }
@@ -295,6 +296,7 @@ void xhci_event_ring_work(unsigned long arg)
 {
 	unsigned long flags;
 	int temp;
+	u64 temp_64;
 	struct xhci_hcd *xhci = (struct xhci_hcd *) arg;
 	int i, j;
 
@@ -311,9 +313,9 @@ void xhci_event_ring_work(unsigned long arg)
 	xhci_dbg(xhci, "Event ring:\n");
 	xhci_debug_segment(xhci, xhci->event_ring->deq_seg);
 	xhci_dbg_ring_ptrs(xhci, xhci->event_ring);
-	temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]);
-	temp &= ERST_PTR_MASK;
-	xhci_dbg(xhci, "ERST deq = 0x%x\n", temp);
+	temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
+	temp_64 &= ~ERST_PTR_MASK;
+	xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64);
 	xhci_dbg(xhci, "Command ring:\n");
 	xhci_debug_segment(xhci, xhci->cmd_ring->deq_seg);
 	xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring);
@@ -356,6 +358,7 @@ void xhci_event_ring_work(unsigned long arg)
 int xhci_run(struct usb_hcd *hcd)
 {
 	u32 temp;
+	u64 temp_64;
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	void (*doorbell)(struct xhci_hcd *) = NULL;
 
@@ -416,11 +419,9 @@ int xhci_run(struct usb_hcd *hcd)
 	xhci_dbg(xhci, "Event ring:\n");
 	xhci_debug_ring(xhci, xhci->event_ring);
 	xhci_dbg_ring_ptrs(xhci, xhci->event_ring);
-	temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]);
-	temp &= ERST_PTR_MASK;
-	xhci_dbg(xhci, "ERST deq = 0x%x\n", temp);
-	temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[1]);
-	xhci_dbg(xhci, "ERST deq upper = 0x%x\n", temp);
+	temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
+	temp_64 &= ~ERST_PTR_MASK;
+	xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64);
 
 	temp = xhci_readl(xhci, &xhci->op_regs->command);
 	temp |= (CMD_RUN);
@@ -888,8 +889,7 @@ static void xhci_zero_in_ctx(struct xhci_virt_device *virt_dev)
 		ep_ctx = &virt_dev->in_ctx->ep[i];
 		ep_ctx->ep_info = 0;
 		ep_ctx->ep_info2 = 0;
-		ep_ctx->deq[0] = 0;
-		ep_ctx->deq[1] = 0;
+		ep_ctx->deq = 0;
 		ep_ctx->tx_info = 0;
 	}
 }
@@ -1165,7 +1165,7 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 	struct xhci_virt_device *virt_dev;
 	int ret = 0;
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
-	u32 temp;
+	u64 temp_64;
 
 	if (!udev->slot_id) {
 		xhci_dbg(xhci, "Bad Slot ID %d\n", udev->slot_id);
@@ -1227,18 +1227,13 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 	if (ret) {
 		return ret;
 	}
-	temp = xhci_readl(xhci, &xhci->op_regs->dcbaa_ptr[0]);
-	xhci_dbg(xhci, "Op regs DCBAA ptr[0] = %#08x\n", temp);
-	temp = xhci_readl(xhci, &xhci->op_regs->dcbaa_ptr[1]);
-	xhci_dbg(xhci, "Op regs DCBAA ptr[1] = %#08x\n", temp);
-	xhci_dbg(xhci, "Slot ID %d dcbaa entry[0] @%p = %#08x\n",
-			udev->slot_id,
-			&xhci->dcbaa->dev_context_ptrs[2*udev->slot_id],
-			xhci->dcbaa->dev_context_ptrs[2*udev->slot_id]);
-	xhci_dbg(xhci, "Slot ID %d dcbaa entry[1] @%p = %#08x\n",
+	temp_64 = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr);
+	xhci_dbg(xhci, "Op regs DCBAA ptr = %#016llx\n", temp_64);
+	xhci_dbg(xhci, "Slot ID %d dcbaa entry @%p = %#016llx\n",
 			udev->slot_id,
-			&xhci->dcbaa->dev_context_ptrs[2*udev->slot_id+1],
-			xhci->dcbaa->dev_context_ptrs[2*udev->slot_id+1]);
+			&xhci->dcbaa->dev_context_ptrs[udev->slot_id],
+			(unsigned long long)
+				xhci->dcbaa->dev_context_ptrs[udev->slot_id]);
 	xhci_dbg(xhci, "Output Context DMA address = %#08llx\n",
 			(unsigned long long)virt_dev->out_ctx_dma);
 	xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id);
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index c8a72de1c50..ec825f16dce 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -88,7 +88,7 @@ static void xhci_link_segments(struct xhci_hcd *xhci, struct xhci_segment *prev,
 		return;
 	prev->next = next;
 	if (link_trbs) {
-		prev->trbs[TRBS_PER_SEGMENT-1].link.segment_ptr[0] = next->dma;
+		prev->trbs[TRBS_PER_SEGMENT-1].link.segment_ptr = next->dma;
 
 		/* Set the last TRB in the segment to have a TRB type ID of Link TRB */
 		val = prev->trbs[TRBS_PER_SEGMENT-1].link.control;
@@ -200,8 +200,7 @@ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id)
 		return;
 
 	dev = xhci->devs[slot_id];
-	xhci->dcbaa->dev_context_ptrs[2*slot_id] = 0;
-	xhci->dcbaa->dev_context_ptrs[2*slot_id + 1] = 0;
+	xhci->dcbaa->dev_context_ptrs[slot_id] = 0;
 	if (!dev)
 		return;
 
@@ -265,13 +264,12 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id,
 	 * Point to output device context in dcbaa; skip the output control
 	 * context, which is eight 32 bit fields (or 32 bytes long)
 	 */
-	xhci->dcbaa->dev_context_ptrs[2*slot_id] =
+	xhci->dcbaa->dev_context_ptrs[slot_id] =
 		(u32) dev->out_ctx_dma + (32);
 	xhci_dbg(xhci, "Set slot id %d dcbaa entry %p to 0x%llx\n",
 			slot_id,
-			&xhci->dcbaa->dev_context_ptrs[2*slot_id],
+			&xhci->dcbaa->dev_context_ptrs[slot_id],
 			(unsigned long long)dev->out_ctx_dma);
-	xhci->dcbaa->dev_context_ptrs[2*slot_id + 1] = 0;
 
 	return 1;
 fail:
@@ -360,10 +358,9 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud
 	ep0_ctx->ep_info2 |= MAX_BURST(0);
 	ep0_ctx->ep_info2 |= ERROR_COUNT(3);
 
-	ep0_ctx->deq[0] =
+	ep0_ctx->deq =
 		dev->ep_rings[0]->first_seg->dma;
-	ep0_ctx->deq[0] |= dev->ep_rings[0]->cycle_state;
-	ep0_ctx->deq[1] = 0;
+	ep0_ctx->deq |= dev->ep_rings[0]->cycle_state;
 
 	/* Steps 7 and 8 were done in xhci_alloc_virt_device() */
 
@@ -477,8 +474,7 @@ int xhci_endpoint_init(struct xhci_hcd *xhci,
 	if (!virt_dev->new_ep_rings[ep_index])
 		return -ENOMEM;
 	ep_ring = virt_dev->new_ep_rings[ep_index];
-	ep_ctx->deq[0] = ep_ring->first_seg->dma | ep_ring->cycle_state;
-	ep_ctx->deq[1] = 0;
+	ep_ctx->deq = ep_ring->first_seg->dma | ep_ring->cycle_state;
 
 	ep_ctx->ep_info = xhci_get_endpoint_interval(udev, ep);
 
@@ -535,8 +531,7 @@ void xhci_endpoint_zero(struct xhci_hcd *xhci,
 
 	ep_ctx->ep_info = 0;
 	ep_ctx->ep_info2 = 0;
-	ep_ctx->deq[0] = 0;
-	ep_ctx->deq[1] = 0;
+	ep_ctx->deq = 0;
 	ep_ctx->tx_info = 0;
 	/* Don't free the endpoint ring until the set interface or configuration
 	 * request succeeds.
@@ -551,10 +546,8 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci)
 
 	/* Free the Event Ring Segment Table and the actual Event Ring */
 	xhci_writel(xhci, 0, &xhci->ir_set->erst_size);
-	xhci_writel(xhci, 0, &xhci->ir_set->erst_base[0]);
-	xhci_writel(xhci, 0, &xhci->ir_set->erst_base[1]);
-	xhci_writel(xhci, 0, &xhci->ir_set->erst_dequeue[0]);
-	xhci_writel(xhci, 0, &xhci->ir_set->erst_dequeue[1]);
+	xhci_write_64(xhci, 0, &xhci->ir_set->erst_base);
+	xhci_write_64(xhci, 0, &xhci->ir_set->erst_dequeue);
 	size = sizeof(struct xhci_erst_entry)*(xhci->erst.num_entries);
 	if (xhci->erst.entries)
 		pci_free_consistent(pdev, size,
@@ -566,8 +559,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci)
 	xhci->event_ring = NULL;
 	xhci_dbg(xhci, "Freed event ring\n");
 
-	xhci_writel(xhci, 0, &xhci->op_regs->cmd_ring[0]);
-	xhci_writel(xhci, 0, &xhci->op_regs->cmd_ring[1]);
+	xhci_write_64(xhci, 0, &xhci->op_regs->cmd_ring);
 	if (xhci->cmd_ring)
 		xhci_ring_free(xhci, xhci->cmd_ring);
 	xhci->cmd_ring = NULL;
@@ -586,8 +578,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci)
 	xhci->device_pool = NULL;
 	xhci_dbg(xhci, "Freed device context pool\n");
 
-	xhci_writel(xhci, 0, &xhci->op_regs->dcbaa_ptr[0]);
-	xhci_writel(xhci, 0, &xhci->op_regs->dcbaa_ptr[1]);
+	xhci_write_64(xhci, 0, &xhci->op_regs->dcbaa_ptr);
 	if (xhci->dcbaa)
 		pci_free_consistent(pdev, sizeof(*xhci->dcbaa),
 				xhci->dcbaa, xhci->dcbaa->dma);
@@ -602,6 +593,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
 	dma_addr_t	dma;
 	struct device	*dev = xhci_to_hcd(xhci)->self.controller;
 	unsigned int	val, val2;
+	u64		val_64;
 	struct xhci_segment	*seg;
 	u32 page_size;
 	int i;
@@ -647,8 +639,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
 	xhci->dcbaa->dma = dma;
 	xhci_dbg(xhci, "// Device context base array address = 0x%llx (DMA), %p (virt)\n",
 			(unsigned long long)xhci->dcbaa->dma, xhci->dcbaa);
-	xhci_writel(xhci, dma, &xhci->op_regs->dcbaa_ptr[0]);
-	xhci_writel(xhci, (u32) 0, &xhci->op_regs->dcbaa_ptr[1]);
+	xhci_write_64(xhci, dma, &xhci->op_regs->dcbaa_ptr);
 
 	/*
 	 * Initialize the ring segment pool.  The ring must be a contiguous
@@ -675,14 +666,12 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
 			(unsigned long long)xhci->cmd_ring->first_seg->dma);
 
 	/* Set the address in the Command Ring Control register */
-	val = xhci_readl(xhci, &xhci->op_regs->cmd_ring[0]);
-	val = (val & ~CMD_RING_ADDR_MASK) |
-		(xhci->cmd_ring->first_seg->dma & CMD_RING_ADDR_MASK) |
+	val_64 = xhci_read_64(xhci, &xhci->op_regs->cmd_ring);
+	val_64 = (val_64 & (u64) CMD_RING_RSVD_BITS) |
+		(xhci->cmd_ring->first_seg->dma & (u64) ~CMD_RING_RSVD_BITS) |
 		xhci->cmd_ring->cycle_state;
-	xhci_dbg(xhci, "// Setting command ring address low bits to 0x%x\n", val);
-	xhci_writel(xhci, val, &xhci->op_regs->cmd_ring[0]);
-	xhci_dbg(xhci, "// Setting command ring address high bits to 0x0\n");
-	xhci_writel(xhci, (u32) 0, &xhci->op_regs->cmd_ring[1]);
+	xhci_dbg(xhci, "// Setting command ring address to 0x%x\n", val);
+	xhci_write_64(xhci, val_64, &xhci->op_regs->cmd_ring);
 	xhci_dbg_cmd_ptrs(xhci);
 
 	val = xhci_readl(xhci, &xhci->cap_regs->db_off);
@@ -722,8 +711,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
 	/* set ring base address and size for each segment table entry */
 	for (val = 0, seg = xhci->event_ring->first_seg; val < ERST_NUM_SEGS; val++) {
 		struct xhci_erst_entry *entry = &xhci->erst.entries[val];
-		entry->seg_addr[0] = seg->dma;
-		entry->seg_addr[1] = 0;
+		entry->seg_addr = seg->dma;
 		entry->seg_size = TRBS_PER_SEGMENT;
 		entry->rsvd = 0;
 		seg = seg->next;
@@ -741,11 +729,10 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
 	/* set the segment table base address */
 	xhci_dbg(xhci, "// Set ERST base address for ir_set 0 = 0x%llx\n",
 			(unsigned long long)xhci->erst.erst_dma_addr);
-	val = xhci_readl(xhci, &xhci->ir_set->erst_base[0]);
-	val &= ERST_PTR_MASK;
-	val |= (xhci->erst.erst_dma_addr & ~ERST_PTR_MASK);
-	xhci_writel(xhci, val, &xhci->ir_set->erst_base[0]);
-	xhci_writel(xhci, 0, &xhci->ir_set->erst_base[1]);
+	val_64 = xhci_read_64(xhci, &xhci->ir_set->erst_base);
+	val_64 &= ERST_PTR_MASK;
+	val_64 |= (xhci->erst.erst_dma_addr & (u64) ~ERST_PTR_MASK);
+	xhci_write_64(xhci, val_64, &xhci->ir_set->erst_base);
 
 	/* Set the event ring dequeue address */
 	xhci_set_hc_event_deq(xhci);
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index d672ba14ff8..588686fca47 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -237,7 +237,7 @@ static int room_on_ring(struct xhci_hcd *xhci, struct xhci_ring *ring,
 
 void xhci_set_hc_event_deq(struct xhci_hcd *xhci)
 {
-	u32 temp;
+	u64 temp;
 	dma_addr_t deq;
 
 	deq = xhci_trb_virt_to_dma(xhci->event_ring->deq_seg,
@@ -246,13 +246,12 @@ void xhci_set_hc_event_deq(struct xhci_hcd *xhci)
 		xhci_warn(xhci, "WARN something wrong with SW event ring "
 				"dequeue ptr.\n");
 	/* Update HC event ring dequeue pointer */
-	temp = xhci_readl(xhci, &xhci->ir_set->erst_dequeue[0]);
+	temp = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
 	temp &= ERST_PTR_MASK;
 	if (!in_interrupt())
 		xhci_dbg(xhci, "// Write event ring dequeue pointer\n");
-	xhci_writel(xhci, 0, &xhci->ir_set->erst_dequeue[1]);
-	xhci_writel(xhci, (deq & ~ERST_PTR_MASK) | temp,
-			&xhci->ir_set->erst_dequeue[0]);
+	xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp,
+			&xhci->ir_set->erst_dequeue);
 }
 
 /* Ring the host controller doorbell after placing a command on the ring */
@@ -352,7 +351,7 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci,
 	if (!state->new_deq_seg)
 		BUG();
 	/* Dig out the cycle state saved by the xHC during the stop ep cmd */
-	state->new_cycle_state = 0x1 & dev->out_ctx->ep[ep_index].deq[0];
+	state->new_cycle_state = 0x1 & dev->out_ctx->ep[ep_index].deq;
 
 	state->new_deq_ptr = cur_td->last_trb;
 	state->new_deq_seg = find_trb_seg(state->new_deq_seg,
@@ -594,10 +593,8 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci,
 		 * cancelling URBs, which might not be an error...
 		 */
 	} else {
-		xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq[0] = 0x%x, "
-				"deq[1] = 0x%x.\n",
-				dev->out_ctx->ep[ep_index].deq[0],
-				dev->out_ctx->ep[ep_index].deq[1]);
+		xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq = @%08llx\n",
+				dev->out_ctx->ep[ep_index].deq);
 	}
 
 	ep_ring->state &= ~SET_DEQ_PENDING;
@@ -631,7 +628,7 @@ static void handle_cmd_completion(struct xhci_hcd *xhci,
 	u64 cmd_dma;
 	dma_addr_t cmd_dequeue_dma;
 
-	cmd_dma = (((u64) event->cmd_trb[1]) << 32) + event->cmd_trb[0];
+	cmd_dma = event->cmd_trb;
 	cmd_dequeue_dma = xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg,
 			xhci->cmd_ring->dequeue);
 	/* Is the command ring deq ptr out of sync with the deq seg ptr? */
@@ -794,10 +791,7 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 		return -ENODEV;
 	}
 
-	event_dma = event->buffer[0];
-	if (event->buffer[1] != 0)
-		xhci_warn(xhci, "WARN ignoring upper 32-bits of 64-bit TRB dma address\n");
-
+	event_dma = event->buffer;
 	/* This TRB should be in the TD at the head of this ring's TD list */
 	if (list_empty(&ep_ring->td_list)) {
 		xhci_warn(xhci, "WARN Event TRB for slot %d ep %d with no TDs queued?\n",
@@ -821,10 +815,10 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 	event_trb = &event_seg->trbs[(event_dma - event_seg->dma) / sizeof(*event_trb)];
 	xhci_dbg(xhci, "Event TRB with TRB type ID %u\n",
 			(unsigned int) (event->flags & TRB_TYPE_BITMASK)>>10);
-	xhci_dbg(xhci, "Offset 0x00 (buffer[0]) = 0x%x\n",
-			(unsigned int) event->buffer[0]);
-	xhci_dbg(xhci, "Offset 0x04 (buffer[0]) = 0x%x\n",
-			(unsigned int) event->buffer[1]);
+	xhci_dbg(xhci, "Offset 0x00 (buffer lo) = 0x%x\n",
+			lower_32_bits(event->buffer));
+	xhci_dbg(xhci, "Offset 0x04 (buffer hi) = 0x%x\n",
+			upper_32_bits(event->buffer));
 	xhci_dbg(xhci, "Offset 0x08 (transfer length) = 0x%x\n",
 			(unsigned int) event->transfer_len);
 	xhci_dbg(xhci, "Offset 0x0C (flags) = 0x%x\n",
@@ -1343,8 +1337,8 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 			TD_REMAINDER(urb->transfer_buffer_length - running_total) |
 			TRB_INTR_TARGET(0);
 		queue_trb(xhci, ep_ring, false,
-				(u32) addr,
-				(u32) ((u64) addr >> 32),
+				lower_32_bits(addr),
+				upper_32_bits(addr),
 				length_field,
 				/* We always want to know if the TRB was short,
 				 * or we won't get an event when it completes.
@@ -1475,8 +1469,8 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
 			TD_REMAINDER(urb->transfer_buffer_length - running_total) |
 			TRB_INTR_TARGET(0);
 		queue_trb(xhci, ep_ring, false,
-				(u32) addr,
-				(u32) ((u64) addr >> 32),
+				lower_32_bits(addr),
+				upper_32_bits(addr),
 				length_field,
 				/* We always want to know if the TRB was short,
 				 * or we won't get an event when it completes.
@@ -1637,7 +1631,8 @@ int xhci_queue_slot_control(struct xhci_hcd *xhci, u32 trb_type, u32 slot_id)
 int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
 		u32 slot_id)
 {
-	return queue_command(xhci, in_ctx_ptr, 0, 0,
+	return queue_command(xhci, lower_32_bits(in_ctx_ptr),
+			upper_32_bits(in_ctx_ptr), 0,
 			TRB_TYPE(TRB_ADDR_DEV) | SLOT_ID_FOR_TRB(slot_id));
 }
 
@@ -1645,7 +1640,8 @@ int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
 int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
 		u32 slot_id)
 {
-	return queue_command(xhci, in_ctx_ptr, 0, 0,
+	return queue_command(xhci, lower_32_bits(in_ctx_ptr),
+			upper_32_bits(in_ctx_ptr), 0,
 			TRB_TYPE(TRB_CONFIG_EP) | SLOT_ID_FOR_TRB(slot_id));
 }
 
@@ -1677,7 +1673,8 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id,
 		xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n");
 		xhci_warn(xhci, "WARN deq seg = %p, deq pt = %p\n",
 				deq_seg, deq_ptr);
-	return queue_command(xhci, (u32) addr | cycle_state, 0, 0,
+	return queue_command(xhci, lower_32_bits(addr) | cycle_state,
+			upper_32_bits(addr), 0,
 			trb_slot_id | trb_ep_index | type);
 }
 
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index cde648a524f..60770c89132 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -25,6 +25,7 @@
 
 #include <linux/usb.h>
 #include <linux/timer.h>
+#include <linux/kernel.h>
 
 #include "../core/hcd.h"
 /* Code sharing between pci-quirks and xhci hcd */
@@ -42,14 +43,6 @@
  * xHCI register interface.
  * This corresponds to the eXtensible Host Controller Interface (xHCI)
  * Revision 0.95 specification
- *
- * Registers should always be accessed with double word or quad word accesses.
- *
- * Some xHCI implementations may support 64-bit address pointers.  Registers
- * with 64-bit address pointers should be written to with dword accesses by
- * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
- * xHCI implementations that do not support 64-bit address pointers will ignore
- * the high dword, and write order is irrelevant.
  */
 
 /**
@@ -166,10 +159,10 @@ struct xhci_op_regs {
 	u32	reserved1;
 	u32	reserved2;
 	u32	dev_notification;
-	u32	cmd_ring[2];
+	u64	cmd_ring;
 	/* rsvd: offset 0x20-2F */
 	u32	reserved3[4];
-	u32	dcbaa_ptr[2];
+	u64	dcbaa_ptr;
 	u32	config_reg;
 	/* rsvd: offset 0x3C-3FF */
 	u32	reserved4[241];
@@ -254,7 +247,7 @@ struct xhci_op_regs {
 #define CMD_RING_RUNNING	(1 << 3)
 /* bits 4:5 reserved and should be preserved */
 /* Command Ring pointer - bit mask for the lower 32 bits. */
-#define CMD_RING_ADDR_MASK	(0xffffffc0)
+#define CMD_RING_RSVD_BITS	(0x3f)
 
 /* CONFIG - Configure Register - config_reg bitmasks */
 /* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */
@@ -382,8 +375,8 @@ struct xhci_intr_reg {
 	u32	irq_control;
 	u32	erst_size;
 	u32	rsvd;
-	u32	erst_base[2];
-	u32	erst_dequeue[2];
+	u64	erst_base;
+	u64	erst_dequeue;
 };
 
 /* irq_pending bitmasks */
@@ -538,7 +531,7 @@ struct xhci_slot_ctx {
 struct xhci_ep_ctx {
 	u32	ep_info;
 	u32	ep_info2;
-	u32	deq[2];
+	u64	deq;
 	u32	tx_info;
 	/* offset 0x14 - 0x1f reserved for HC internal use */
 	u32	reserved[3];
@@ -641,7 +634,7 @@ struct xhci_virt_device {
  */
 struct xhci_device_context_array {
 	/* 64-bit device addresses; we only write 32-bit addresses */
-	u32			dev_context_ptrs[2*MAX_HC_SLOTS];
+	u64			dev_context_ptrs[MAX_HC_SLOTS];
 	/* private xHCD pointers */
 	dma_addr_t	dma;
 };
@@ -654,7 +647,7 @@ struct xhci_device_context_array {
 
 struct xhci_stream_ctx {
 	/* 64-bit stream ring address, cycle state, and stream type */
-	u32	stream_ring[2];
+	u64	stream_ring;
 	/* offset 0x14 - 0x1f reserved for HC internal use */
 	u32	reserved[2];
 };
@@ -662,7 +655,7 @@ struct xhci_stream_ctx {
 
 struct xhci_transfer_event {
 	/* 64-bit buffer address, or immediate data */
-	u32	buffer[2];
+	u64	buffer;
 	u32	transfer_len;
 	/* This field is interpreted differently based on the type of TRB */
 	u32	flags;
@@ -744,7 +737,7 @@ struct xhci_transfer_event {
 
 struct xhci_link_trb {
 	/* 64-bit segment pointer*/
-	u32 segment_ptr[2];
+	u64 segment_ptr;
 	u32 intr_target;
 	u32 control;
 };
@@ -755,7 +748,7 @@ struct xhci_link_trb {
 /* Command completion event TRB */
 struct xhci_event_cmd {
 	/* Pointer to command TRB, or the value passed by the event data trb */
-	u32 cmd_trb[2];
+	u64 cmd_trb;
 	u32 status;
 	u32 flags;
 };
@@ -943,7 +936,7 @@ struct xhci_ring {
 
 struct xhci_erst_entry {
 	/* 64-bit event ring segment address */
-	u32	seg_addr[2];
+	u64	seg_addr;
 	u32	seg_size;
 	/* Set to zero */
 	u32	rsvd;
@@ -1079,6 +1072,38 @@ static inline void xhci_writel(struct xhci_hcd *xhci,
 	writel(val, regs);
 }
 
+/*
+ * Registers should always be accessed with double word or quad word accesses.
+ *
+ * Some xHCI implementations may support 64-bit address pointers.  Registers
+ * with 64-bit address pointers should be written to with dword accesses by
+ * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
+ * xHCI implementations that do not support 64-bit address pointers will ignore
+ * the high dword, and write order is irrelevant.
+ */
+static inline u64 xhci_read_64(const struct xhci_hcd *xhci,
+		__u64 __iomem *regs)
+{
+	__u32 __iomem *ptr = (__u32 __iomem *) regs;
+	u64 val_lo = readl(ptr);
+	u64 val_hi = readl(ptr + 1);
+	return val_lo + (val_hi << 32);
+}
+static inline void xhci_write_64(struct xhci_hcd *xhci,
+		const u64 val, __u64 __iomem *regs)
+{
+	__u32 __iomem *ptr = (__u32 __iomem *) regs;
+	u32 val_lo = lower_32_bits(val);
+	u32 val_hi = upper_32_bits(val);
+
+	if (!in_interrupt())
+		xhci_dbg(xhci,
+			 "`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n",
+			 regs, (long unsigned int) val);
+	writel(val_lo, ptr);
+	writel(val_hi, ptr + 1);
+}
+
 /* xHCI debugging */
 void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int set_num);
 void xhci_print_registers(struct xhci_hcd *xhci);
-- 
GitLab


From 62889610f5591005bed9517360e17531684f72d0 Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:03:36 -0700
Subject: [PATCH 0182/1153] USB: xhci: Handle short control packets correctly.

When there is a short packet on a control transfer, the xHCI host controller
hardware will generate two events.  The first event will be for the data stage
TD with a completion code for a short packet.  The second event will be for the
status stage with a successful completion code.  Before this patch, the xHCI
driver would giveback the short control URB when it received the event for the
data stage TD.  Then it would become confused when it saw a status stage event
for the endpoint for an URB it had already finished processing.

Change the xHCI host controller driver to wait for the status stage event when
it receives a short transfer completion code for a data stage TD.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-ring.c | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 588686fca47..5dd3b1fd71c 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -892,15 +892,23 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 		if (event_trb != ep_ring->dequeue) {
 			/* The event was for the status stage */
 			if (event_trb == td->last_trb) {
-				td->urb->actual_length =
-					td->urb->transfer_buffer_length;
+				/* Did we already see a short data stage? */
+				if (td->urb->actual_length != 0)
+					status = -EREMOTEIO;
+				else
+					td->urb->actual_length =
+						td->urb->transfer_buffer_length;
 			} else {
 			/* Maybe the event was for the data stage? */
-				if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL)
+				if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) {
 					/* We didn't stop on a link TRB in the middle */
 					td->urb->actual_length =
 						td->urb->transfer_buffer_length -
 						TRB_LEN(event->transfer_len);
+					xhci_dbg(xhci, "Waiting for status stage event\n");
+					urb = NULL;
+					goto cleanup;
+				}
 			}
 		}
 	} else {
-- 
GitLab


From 2d83109be62edd9647c45d7ed2b916b03974a7ec Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:03:40 -0700
Subject: [PATCH 0183/1153] USB: xhci: Correct Event Handler Busy flag usage.

The Event Handler Busy bit in the event ring dequeue pointer is write 1 to
clear.  Fix the interrupt service routine to clear that bit after the
event handler has run.

xhci_set_hc_event_deq() is designed to update the event ring dequeue pointer
without changing any of the four reserved bits in the lower nibble.  The event
handler busy (EHB) bit is write one to clear, so the new value must always
contain a zero in that bit in order to preserve the EHB value.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-hcd.c  | 4 ++--
 drivers/usb/host/xhci-ring.c | 6 +++++-
 2 files changed, 7 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c
index e15773598e4..2e8e5bf6b6c 100644
--- a/drivers/usb/host/xhci-hcd.c
+++ b/drivers/usb/host/xhci-hcd.c
@@ -249,9 +249,9 @@ static void xhci_work(struct xhci_hcd *xhci)
 	/* FIXME this should be a delayed service routine that clears the EHB */
 	xhci_handle_event(xhci);
 
-	/* Clear the event handler busy flag; the event ring should be empty. */
+	/* Clear the event handler busy flag (RW1C); the event ring should be empty. */
 	temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
-	xhci_write_64(xhci, temp_64 & ~ERST_EHB, &xhci->ir_set->erst_dequeue);
+	xhci_write_64(xhci, temp_64 | ERST_EHB, &xhci->ir_set->erst_dequeue);
 	/* Flush posted writes -- FIXME is this necessary? */
 	xhci_readl(xhci, &xhci->ir_set->irq_pending);
 }
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 5dd3b1fd71c..fe9541a89a3 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -248,8 +248,12 @@ void xhci_set_hc_event_deq(struct xhci_hcd *xhci)
 	/* Update HC event ring dequeue pointer */
 	temp = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
 	temp &= ERST_PTR_MASK;
+	/* Don't clear the EHB bit (which is RW1C) because
+	 * there might be more events to service.
+	 */
+	temp &= ~ERST_EHB;
 	if (!in_interrupt())
-		xhci_dbg(xhci, "// Write event ring dequeue pointer\n");
+		xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n");
 	xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp,
 			&xhci->ir_set->erst_dequeue);
 }
-- 
GitLab


From 66e49d8774fa03539713e8f91169c37c05df1e94 Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:03:46 -0700
Subject: [PATCH 0184/1153] USB: xhci: Make debugging more verbose.

Add more debugging to the irq handler, slot context initialization, ring
operations, URB cancellation, and MMIO writes.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-hcd.c  | 47 +++++++++++++++++++++++++-----------
 drivers/usb/host/xhci-ring.c | 35 +++++++++++++++++++++++++--
 drivers/usb/host/xhci.h      | 14 +++++------
 3 files changed, 72 insertions(+), 24 deletions(-)

diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c
index 2e8e5bf6b6c..764995fd59e 100644
--- a/drivers/usb/host/xhci-hcd.c
+++ b/drivers/usb/host/xhci-hcd.c
@@ -267,8 +267,10 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd)
 {
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	u32 temp, temp2;
+	union xhci_trb *trb;
 
 	spin_lock(&xhci->lock);
+	trb = xhci->event_ring->dequeue;
 	/* Check if the xHC generated the interrupt, or the irq is shared */
 	temp = xhci_readl(xhci, &xhci->op_regs->status);
 	temp2 = xhci_readl(xhci, &xhci->ir_set->irq_pending);
@@ -276,6 +278,15 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd)
 		spin_unlock(&xhci->lock);
 		return IRQ_NONE;
 	}
+	xhci_dbg(xhci, "op reg status = %08x\n", temp);
+	xhci_dbg(xhci, "ir set irq_pending = %08x\n", temp2);
+	xhci_dbg(xhci, "Event ring dequeue ptr:\n");
+	xhci_dbg(xhci, "@%llx %08x %08x %08x %08x\n",
+			(unsigned long long)xhci_trb_virt_to_dma(xhci->event_ring->deq_seg, trb),
+			lower_32_bits(trb->link.segment_ptr),
+			upper_32_bits(trb->link.segment_ptr),
+			(unsigned int) trb->link.intr_target,
+			(unsigned int) trb->link.control);
 
 	if (temp & STS_FATAL) {
 		xhci_warn(xhci, "WARNING: Host System Error\n");
@@ -385,6 +396,20 @@ int xhci_run(struct usb_hcd *hcd)
 	add_timer(&xhci->event_ring_timer);
 #endif
 
+	xhci_dbg(xhci, "Command ring memory map follows:\n");
+	xhci_debug_ring(xhci, xhci->cmd_ring);
+	xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring);
+	xhci_dbg_cmd_ptrs(xhci);
+
+	xhci_dbg(xhci, "ERST memory map follows:\n");
+	xhci_dbg_erst(xhci, &xhci->erst);
+	xhci_dbg(xhci, "Event ring:\n");
+	xhci_debug_ring(xhci, xhci->event_ring);
+	xhci_dbg_ring_ptrs(xhci, xhci->event_ring);
+	temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
+	temp_64 &= ~ERST_PTR_MASK;
+	xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64);
+
 	xhci_dbg(xhci, "// Set the interrupt modulation register\n");
 	temp = xhci_readl(xhci, &xhci->ir_set->irq_control);
 	temp &= ~ER_IRQ_INTERVAL_MASK;
@@ -409,20 +434,6 @@ int xhci_run(struct usb_hcd *hcd)
 	if (NUM_TEST_NOOPS > 0)
 		doorbell = xhci_setup_one_noop(xhci);
 
-	xhci_dbg(xhci, "Command ring memory map follows:\n");
-	xhci_debug_ring(xhci, xhci->cmd_ring);
-	xhci_dbg_ring_ptrs(xhci, xhci->cmd_ring);
-	xhci_dbg_cmd_ptrs(xhci);
-
-	xhci_dbg(xhci, "ERST memory map follows:\n");
-	xhci_dbg_erst(xhci, &xhci->erst);
-	xhci_dbg(xhci, "Event ring:\n");
-	xhci_debug_ring(xhci, xhci->event_ring);
-	xhci_dbg_ring_ptrs(xhci, xhci->event_ring);
-	temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
-	temp_64 &= ~ERST_PTR_MASK;
-	xhci_dbg(xhci, "ERST deq = 64'h%0lx\n", (long unsigned int) temp_64);
-
 	temp = xhci_readl(xhci, &xhci->op_regs->command);
 	temp |= (CMD_RUN);
 	xhci_dbg(xhci, "// Turn on HC, cmd = 0x%x.\n",
@@ -665,8 +676,12 @@ int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
 		goto done;
 
 	xhci_dbg(xhci, "Cancel URB %p\n", urb);
+	xhci_dbg(xhci, "Event ring:\n");
+	xhci_debug_ring(xhci, xhci->event_ring);
 	ep_index = xhci_get_endpoint_index(&urb->ep->desc);
 	ep_ring = xhci->devs[urb->dev->slot_id]->ep_rings[ep_index];
+	xhci_dbg(xhci, "Endpoint ring:\n");
+	xhci_debug_ring(xhci, ep_ring);
 	td = (struct xhci_td *) urb->hcpriv;
 
 	ep_ring->cancels_pending++;
@@ -1178,6 +1193,8 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 	if (!udev->config)
 		xhci_setup_addressable_virt_dev(xhci, udev);
 	/* Otherwise, assume the core has the device configured how it wants */
+	xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id);
+	xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2);
 
 	spin_lock_irqsave(&xhci->lock, flags);
 	ret = xhci_queue_address_device(xhci, virt_dev->in_ctx_dma,
@@ -1221,6 +1238,8 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 	default:
 		xhci_err(xhci, "ERROR: unexpected command completion "
 				"code 0x%x.\n", virt_dev->cmd_status);
+		xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id);
+		xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2);
 		ret = -EINVAL;
 		break;
 	}
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index fe9541a89a3..1fc0decfa0a 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -135,6 +135,7 @@ static void next_trb(struct xhci_hcd *xhci,
 static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer)
 {
 	union xhci_trb *next = ++(ring->dequeue);
+	unsigned long long addr;
 
 	ring->deq_updates++;
 	/* Update the dequeue pointer further if that was a link TRB or we're at
@@ -152,6 +153,13 @@ static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer
 		ring->dequeue = ring->deq_seg->trbs;
 		next = ring->dequeue;
 	}
+	addr = (unsigned long long) xhci_trb_virt_to_dma(ring->deq_seg, ring->dequeue);
+	if (ring == xhci->event_ring)
+		xhci_dbg(xhci, "Event ring deq = 0x%llx (DMA)\n", addr);
+	else if (ring == xhci->cmd_ring)
+		xhci_dbg(xhci, "Command ring deq = 0x%llx (DMA)\n", addr);
+	else
+		xhci_dbg(xhci, "Ring deq = 0x%llx (DMA)\n", addr);
 }
 
 /*
@@ -171,6 +179,7 @@ static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer
 {
 	u32 chain;
 	union xhci_trb *next;
+	unsigned long long addr;
 
 	chain = ring->enqueue->generic.field[3] & TRB_CHAIN;
 	next = ++(ring->enqueue);
@@ -204,6 +213,13 @@ static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer
 		ring->enqueue = ring->enq_seg->trbs;
 		next = ring->enqueue;
 	}
+	addr = (unsigned long long) xhci_trb_virt_to_dma(ring->enq_seg, ring->enqueue);
+	if (ring == xhci->event_ring)
+		xhci_dbg(xhci, "Event ring enq = 0x%llx (DMA)\n", addr);
+	else if (ring == xhci->cmd_ring)
+		xhci_dbg(xhci, "Command ring enq = 0x%llx (DMA)\n", addr);
+	else
+		xhci_dbg(xhci, "Ring enq = 0x%llx (DMA)\n", addr);
 }
 
 /*
@@ -252,8 +268,7 @@ void xhci_set_hc_event_deq(struct xhci_hcd *xhci)
 	 * there might be more events to service.
 	 */
 	temp &= ~ERST_EHB;
-	if (!in_interrupt())
-		xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n");
+	xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n");
 	xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp,
 			&xhci->ir_set->erst_dequeue);
 }
@@ -781,6 +796,7 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 	struct urb *urb = 0;
 	int status = -EINPROGRESS;
 
+	xhci_dbg(xhci, "In %s\n", __func__);
 	xdev = xhci->devs[TRB_TO_SLOT_ID(event->flags)];
 	if (!xdev) {
 		xhci_err(xhci, "ERROR Transfer event pointed to bad slot\n");
@@ -789,6 +805,7 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 
 	/* Endpoint ID is 1 based, our index is zero based */
 	ep_index = TRB_TO_EP_ID(event->flags) - 1;
+	xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index);
 	ep_ring = xdev->ep_rings[ep_index];
 	if (!ep_ring || (xdev->out_ctx->ep[ep_index].ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) {
 		xhci_err(xhci, "ERROR Transfer event pointed to disabled endpoint\n");
@@ -797,6 +814,7 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 
 	event_dma = event->buffer;
 	/* This TRB should be in the TD at the head of this ring's TD list */
+	xhci_dbg(xhci, "%s - checking for list empty\n", __func__);
 	if (list_empty(&ep_ring->td_list)) {
 		xhci_warn(xhci, "WARN Event TRB for slot %d ep %d with no TDs queued?\n",
 				TRB_TO_SLOT_ID(event->flags), ep_index);
@@ -806,11 +824,14 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 		urb = NULL;
 		goto cleanup;
 	}
+	xhci_dbg(xhci, "%s - getting list entry\n", __func__);
 	td = list_entry(ep_ring->td_list.next, struct xhci_td, td_list);
 
 	/* Is this a TRB in the currently executing TD? */
+	xhci_dbg(xhci, "%s - looking for TD\n", __func__);
 	event_seg = trb_in_td(ep_ring->deq_seg, ep_ring->dequeue,
 			td->last_trb, event_dma);
+	xhci_dbg(xhci, "%s - found event_seg = %p\n", __func__, event_seg);
 	if (!event_seg) {
 		/* HC is busted, give up! */
 		xhci_err(xhci, "ERROR Transfer event TRB DMA ptr not part of current TD\n");
@@ -1027,6 +1048,8 @@ cleanup:
 	/* FIXME for multi-TD URBs (who have buffers bigger than 64MB) */
 	if (urb) {
 		usb_hcd_unlink_urb_from_ep(xhci_to_hcd(xhci), urb);
+		xhci_dbg(xhci, "Giveback URB %p, len = %d, status = %d\n",
+				urb, td->urb->actual_length, status);
 		spin_unlock(&xhci->lock);
 		usb_hcd_giveback_urb(xhci_to_hcd(xhci), urb, status);
 		spin_lock(&xhci->lock);
@@ -1044,6 +1067,7 @@ void xhci_handle_event(struct xhci_hcd *xhci)
 	int update_ptrs = 1;
 	int ret;
 
+	xhci_dbg(xhci, "In %s\n", __func__);
 	if (!xhci->event_ring || !xhci->event_ring->dequeue) {
 		xhci->error_bitmask |= 1 << 1;
 		return;
@@ -1056,18 +1080,25 @@ void xhci_handle_event(struct xhci_hcd *xhci)
 		xhci->error_bitmask |= 1 << 2;
 		return;
 	}
+	xhci_dbg(xhci, "%s - OS owns TRB\n", __func__);
 
 	/* FIXME: Handle more event types. */
 	switch ((event->event_cmd.flags & TRB_TYPE_BITMASK)) {
 	case TRB_TYPE(TRB_COMPLETION):
+		xhci_dbg(xhci, "%s - calling handle_cmd_completion\n", __func__);
 		handle_cmd_completion(xhci, &event->event_cmd);
+		xhci_dbg(xhci, "%s - returned from handle_cmd_completion\n", __func__);
 		break;
 	case TRB_TYPE(TRB_PORT_STATUS):
+		xhci_dbg(xhci, "%s - calling handle_port_status\n", __func__);
 		handle_port_status(xhci, event);
+		xhci_dbg(xhci, "%s - returned from handle_port_status\n", __func__);
 		update_ptrs = 0;
 		break;
 	case TRB_TYPE(TRB_TRANSFER):
+		xhci_dbg(xhci, "%s - calling handle_tx_event\n", __func__);
 		ret = handle_tx_event(xhci, &event->trans_event);
+		xhci_dbg(xhci, "%s - returned from handle_tx_event\n", __func__);
 		if (ret < 0)
 			xhci->error_bitmask |= 1 << 9;
 		else
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 60770c89132..074728e1022 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1065,10 +1065,9 @@ static inline unsigned int xhci_readl(const struct xhci_hcd *xhci,
 static inline void xhci_writel(struct xhci_hcd *xhci,
 		const unsigned int val, __u32 __iomem *regs)
 {
-	if (!in_interrupt())
-		xhci_dbg(xhci,
-			 "`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n",
-			 regs, val);
+	xhci_dbg(xhci,
+			"`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n",
+			regs, val);
 	writel(val, regs);
 }
 
@@ -1096,10 +1095,9 @@ static inline void xhci_write_64(struct xhci_hcd *xhci,
 	u32 val_lo = lower_32_bits(val);
 	u32 val_hi = upper_32_bits(val);
 
-	if (!in_interrupt())
-		xhci_dbg(xhci,
-			 "`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n",
-			 regs, (long unsigned int) val);
+	xhci_dbg(xhci,
+			"`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n",
+			regs, (long unsigned int) val);
 	writel(val_lo, ptr);
 	writel(val_hi, ptr + 1);
 }
-- 
GitLab


From d3512f63494678dc58e44a20c56278718fd58969 Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:03:50 -0700
Subject: [PATCH 0185/1153] USB: xhci: Don't oops if the host doesn't halt.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-hcd.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c
index 764995fd59e..8c3a074a95c 100644
--- a/drivers/usb/host/xhci-hcd.c
+++ b/drivers/usb/host/xhci-hcd.c
@@ -103,7 +103,10 @@ int xhci_reset(struct xhci_hcd *xhci)
 	u32 state;
 
 	state = xhci_readl(xhci, &xhci->op_regs->status);
-	BUG_ON((state & STS_HALT) == 0);
+	if ((state & STS_HALT) == 0) {
+		xhci_warn(xhci, "Host controller not halted, aborting reset.\n");
+		return 0;
+	}
 
 	xhci_dbg(xhci, "// Reset the HC\n");
 	command = xhci_readl(xhci, &xhci->op_regs->command);
-- 
GitLab


From fcf8f576beafb8c5db8aee8a73eb73763fa7b0ad Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:04:01 -0700
Subject: [PATCH 0186/1153] USB: xhci: Check if the host controller died in IRQ
 handler.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-hcd.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c
index 8c3a074a95c..008326d5bc5 100644
--- a/drivers/usb/host/xhci-hcd.c
+++ b/drivers/usb/host/xhci-hcd.c
@@ -277,6 +277,9 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd)
 	/* Check if the xHC generated the interrupt, or the irq is shared */
 	temp = xhci_readl(xhci, &xhci->op_regs->status);
 	temp2 = xhci_readl(xhci, &xhci->ir_set->irq_pending);
+	if (temp == 0xffffffff && temp2 == 0xffffffff)
+		goto hw_died;
+
 	if (!(temp & STS_EINT) && !ER_IRQ_PENDING(temp2)) {
 		spin_unlock(&xhci->lock);
 		return IRQ_NONE;
@@ -294,6 +297,7 @@ irqreturn_t xhci_irq(struct usb_hcd *hcd)
 	if (temp & STS_FATAL) {
 		xhci_warn(xhci, "WARNING: Host System Error\n");
 		xhci_halt(xhci);
+hw_died:
 		xhci_to_hcd(xhci)->state = HC_STATE_HALT;
 		spin_unlock(&xhci->lock);
 		return -ESHUTDOWN;
-- 
GitLab


From 47692d179f7a88794bcd302e53ca7899d7592db9 Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:04:27 -0700
Subject: [PATCH 0187/1153] USB: xhci: Setup HW retries correctly.

The xHCI host controller can be programmed to retry a transfer a certain number
of times per endpoint before it passes back an error condition to the host
controller driver.  The xHC will return an error code when the error count
transitions from 1 to 0.  Programming an error count of 3 means the xHC tries
the transfer 3 times, programming it with a 1 means it tries to transfer once,
and programming it with 0 means the HW tries the transfer infinitely.

We want isochronous transfers to only be tried once, so set the error count to
one.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-mem.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index ec825f16dce..075e1036bcb 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -480,11 +480,13 @@ int xhci_endpoint_init(struct xhci_hcd *xhci,
 
 	/* FIXME dig Mult and streams info out of ep companion desc */
 
-	/* Allow 3 retries for everything but isoc */
+	/* Allow 3 retries for everything but isoc;
+	 * error count = 0 means infinite retries.
+	 */
 	if (!usb_endpoint_xfer_isoc(&ep->desc))
 		ep_ctx->ep_info2 = ERROR_COUNT(3);
 	else
-		ep_ctx->ep_info2 = ERROR_COUNT(0);
+		ep_ctx->ep_info2 = ERROR_COUNT(1);
 
 	ep_ctx->ep_info2 |= xhci_get_endpoint_type(udev, ep);
 
-- 
GitLab


From 4a73143ced467868e92d7914d9f8bf797640927b Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:04:32 -0700
Subject: [PATCH 0188/1153] USB: xhci: Handle babble errors on transfers.

Pass back a babble error when this error code is seen in the transfer event TRB.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-ring.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 1fc0decfa0a..0903e98989e 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -876,6 +876,10 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 		xhci_warn(xhci, "WARN: transfer error on endpoint\n");
 		status = -EPROTO;
 		break;
+	case COMP_BABBLE:
+		xhci_warn(xhci, "WARN: babble error on endpoint\n");
+		status = -EOVERFLOW;
+		break;
 	case COMP_DB_ERR:
 		xhci_warn(xhci, "WARN: HC couldn't access mem fast enough\n");
 		status = -ENOSR;
-- 
GitLab


From b7d6d99896a6cf38dc354d673afd3fbde10b86c2 Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:04:38 -0700
Subject: [PATCH 0189/1153] USB: xhci: Fail gracefully if there's no SS ep
 companion descriptor.

This is a work around for a bug in the SuperSpeed Endpoint Companion Descriptor
parsing code.  It fails in some corner cases, which means ep->ss_ep_comp may be
NULL.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-mem.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index 075e1036bcb..41aca003ee8 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -496,7 +496,12 @@ int xhci_endpoint_init(struct xhci_hcd *xhci,
 		max_packet = ep->desc.wMaxPacketSize;
 		ep_ctx->ep_info2 |= MAX_PACKET(max_packet);
 		/* dig out max burst from ep companion desc */
-		max_packet = ep->ss_ep_comp->desc.bMaxBurst;
+		if (!ep->ss_ep_comp) {
+			xhci_warn(xhci, "WARN no SS endpoint companion descriptor.\n");
+			max_packet = 0;
+		} else {
+			max_packet = ep->ss_ep_comp->desc.bMaxBurst;
+		}
 		ep_ctx->ep_info2 |= MAX_BURST(max_packet);
 		break;
 	case USB_SPEED_HIGH:
-- 
GitLab


From 9f8e443816976edd68f415ea25c0223ea921e88c Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:04:52 -0700
Subject: [PATCH 0190/1153] USB: Fix parsing of SuperSpeed Endpoint Companion
 descriptor.

usb_parse_ss_endpoint_companion() was supposed to allocate a structure to
hold the SuperSpeed Endpoint Companion descriptor, and either copy the
values the device returned, or fill in default values if the device
descriptor did not include the companion descriptor.

However, the previous code would miss the last endpoint in a configuration
with no descriptors after it.  Make usb_parse_endpoint() allocate the SS
endpoint companion descriptor and fill it with default values, even if
we've run out of buffer space in this configuration descriptor.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/config.c | 48 ++++++++++++++++++++++-----------------
 1 file changed, 27 insertions(+), 21 deletions(-)

diff --git a/drivers/usb/core/config.c b/drivers/usb/core/config.c
index 24dfb33f90c..a16c538d013 100644
--- a/drivers/usb/core/config.c
+++ b/drivers/usb/core/config.c
@@ -80,38 +80,18 @@ static int usb_parse_ss_endpoint_companion(struct device *ddev, int cfgno,
 	int max_tx;
 	int i;
 
-	/* Allocate space for the SS endpoint companion descriptor */
-	ep->ss_ep_comp = kzalloc(sizeof(struct usb_host_ss_ep_comp),
-			GFP_KERNEL);
-	if (!ep->ss_ep_comp)
-		return -ENOMEM;
 	desc = (struct usb_ss_ep_comp_descriptor *) buffer;
 	if (desc->bDescriptorType != USB_DT_SS_ENDPOINT_COMP) {
 		dev_warn(ddev, "No SuperSpeed endpoint companion for config %d "
 				" interface %d altsetting %d ep %d: "
 				"using minimum values\n",
 				cfgno, inum, asnum, ep->desc.bEndpointAddress);
-		ep->ss_ep_comp->desc.bLength = USB_DT_SS_EP_COMP_SIZE;
-		ep->ss_ep_comp->desc.bDescriptorType = USB_DT_SS_ENDPOINT_COMP;
-		ep->ss_ep_comp->desc.bMaxBurst = 0;
-		/*
-		 * Leave bmAttributes as zero, which will mean no streams for
-		 * bulk, and isoc won't support multiple bursts of packets.
-		 * With bursts of only one packet, and a Mult of 1, the max
-		 * amount of data moved per endpoint service interval is one
-		 * packet.
-		 */
-		if (usb_endpoint_xfer_isoc(&ep->desc) ||
-				usb_endpoint_xfer_int(&ep->desc))
-			ep->ss_ep_comp->desc.wBytesPerInterval =
-				ep->desc.wMaxPacketSize;
 		/*
 		 * The next descriptor is for an Endpoint or Interface,
 		 * no extra descriptors to copy into the companion structure,
 		 * and we didn't eat up any of the buffer.
 		 */
-		retval = 0;
-		goto valid;
+		return 0;
 	}
 	memcpy(&ep->ss_ep_comp->desc, desc, USB_DT_SS_EP_COMP_SIZE);
 	desc = &ep->ss_ep_comp->desc;
@@ -320,6 +300,28 @@ static int usb_parse_endpoint(struct device *ddev, int cfgno, int inum,
 		buffer += i;
 		size -= i;
 
+		/* Allocate space for the SS endpoint companion descriptor */
+		endpoint->ss_ep_comp = kzalloc(sizeof(struct usb_host_ss_ep_comp),
+				GFP_KERNEL);
+		if (!endpoint->ss_ep_comp)
+			return -ENOMEM;
+
+		/* Fill in some default values (may be overwritten later) */
+		endpoint->ss_ep_comp->desc.bLength = USB_DT_SS_EP_COMP_SIZE;
+		endpoint->ss_ep_comp->desc.bDescriptorType = USB_DT_SS_ENDPOINT_COMP;
+		endpoint->ss_ep_comp->desc.bMaxBurst = 0;
+		/*
+		 * Leave bmAttributes as zero, which will mean no streams for
+		 * bulk, and isoc won't support multiple bursts of packets.
+		 * With bursts of only one packet, and a Mult of 1, the max
+		 * amount of data moved per endpoint service interval is one
+		 * packet.
+		 */
+		if (usb_endpoint_xfer_isoc(&endpoint->desc) ||
+				usb_endpoint_xfer_int(&endpoint->desc))
+			endpoint->ss_ep_comp->desc.wBytesPerInterval =
+				endpoint->desc.wMaxPacketSize;
+
 		if (size > 0) {
 			retval = usb_parse_ss_endpoint_companion(ddev, cfgno,
 					inum, asnum, endpoint, num_ep, buffer,
@@ -329,6 +331,10 @@ static int usb_parse_endpoint(struct device *ddev, int cfgno, int inum,
 				retval = buffer - buffer0;
 			}
 		} else {
+			dev_warn(ddev, "config %d interface %d altsetting %d "
+				"endpoint 0x%X has no "
+				"SuperSpeed companion descriptor\n",
+				cfgno, inum, asnum, d->bEndpointAddress);
 			retval = buffer - buffer0;
 		}
 	} else {
-- 
GitLab


From 254c80a3a0eb811489f7410c3291f01a60e8e42f Mon Sep 17 00:00:00 2001
From: John Youn <johnyoun@synopsys.com>
Date: Mon, 27 Jul 2009 12:05:03 -0700
Subject: [PATCH 0191/1153] USB: xhci: Scratchpad buffer allocation

Allocates and initializes the scratchpad buffer array (XHCI 4.20).  This is an
array of 64-bit DMA addresses to scratch pages that the controller may use
during operation.  The number of pages is specified in the "Max Scratchpad
Buffers" field of HCSPARAMS2.  The DMA address of this array is written into
slot 0 of the DCBAA.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-mem.c | 102 ++++++++++++++++++++++++++++++++++++
 drivers/usb/host/xhci.h     |  11 ++++
 2 files changed, 113 insertions(+)

diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index 41aca003ee8..71121d99235 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -545,6 +545,103 @@ void xhci_endpoint_zero(struct xhci_hcd *xhci,
 	 */
 }
 
+/* Set up the scratchpad buffer array and scratchpad buffers, if needed. */
+static int scratchpad_alloc(struct xhci_hcd *xhci, gfp_t flags)
+{
+	int i;
+	struct device *dev = xhci_to_hcd(xhci)->self.controller;
+	int num_sp = HCS_MAX_SCRATCHPAD(xhci->hcs_params2);
+
+	xhci_dbg(xhci, "Allocating %d scratchpad buffers\n", num_sp);
+
+	if (!num_sp)
+		return 0;
+
+	xhci->scratchpad = kzalloc(sizeof(*xhci->scratchpad), flags);
+	if (!xhci->scratchpad)
+		goto fail_sp;
+
+	xhci->scratchpad->sp_array =
+		pci_alloc_consistent(to_pci_dev(dev),
+				     num_sp * sizeof(u64),
+				     &xhci->scratchpad->sp_dma);
+	if (!xhci->scratchpad->sp_array)
+		goto fail_sp2;
+
+	xhci->scratchpad->sp_buffers = kzalloc(sizeof(void *) * num_sp, flags);
+	if (!xhci->scratchpad->sp_buffers)
+		goto fail_sp3;
+
+	xhci->scratchpad->sp_dma_buffers =
+		kzalloc(sizeof(dma_addr_t) * num_sp, flags);
+
+	if (!xhci->scratchpad->sp_dma_buffers)
+		goto fail_sp4;
+
+	xhci->dcbaa->dev_context_ptrs[0] = xhci->scratchpad->sp_dma;
+	for (i = 0; i < num_sp; i++) {
+		dma_addr_t dma;
+		void *buf = pci_alloc_consistent(to_pci_dev(dev),
+						 xhci->page_size, &dma);
+		if (!buf)
+			goto fail_sp5;
+
+		xhci->scratchpad->sp_array[i] = dma;
+		xhci->scratchpad->sp_buffers[i] = buf;
+		xhci->scratchpad->sp_dma_buffers[i] = dma;
+	}
+
+	return 0;
+
+ fail_sp5:
+	for (i = i - 1; i >= 0; i--) {
+		pci_free_consistent(to_pci_dev(dev), xhci->page_size,
+				    xhci->scratchpad->sp_buffers[i],
+				    xhci->scratchpad->sp_dma_buffers[i]);
+	}
+	kfree(xhci->scratchpad->sp_dma_buffers);
+
+ fail_sp4:
+	kfree(xhci->scratchpad->sp_buffers);
+
+ fail_sp3:
+	pci_free_consistent(to_pci_dev(dev), num_sp * sizeof(u64),
+			    xhci->scratchpad->sp_array,
+			    xhci->scratchpad->sp_dma);
+
+ fail_sp2:
+	kfree(xhci->scratchpad);
+	xhci->scratchpad = NULL;
+
+ fail_sp:
+	return -ENOMEM;
+}
+
+static void scratchpad_free(struct xhci_hcd *xhci)
+{
+	int num_sp;
+	int i;
+	struct pci_dev	*pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
+
+	if (!xhci->scratchpad)
+		return;
+
+	num_sp = HCS_MAX_SCRATCHPAD(xhci->hcs_params2);
+
+	for (i = 0; i < num_sp; i++) {
+		pci_free_consistent(pdev, xhci->page_size,
+				    xhci->scratchpad->sp_buffers[i],
+				    xhci->scratchpad->sp_dma_buffers[i]);
+	}
+	kfree(xhci->scratchpad->sp_dma_buffers);
+	kfree(xhci->scratchpad->sp_buffers);
+	pci_free_consistent(pdev, num_sp * sizeof(u64),
+			    xhci->scratchpad->sp_array,
+			    xhci->scratchpad->sp_dma);
+	kfree(xhci->scratchpad);
+	xhci->scratchpad = NULL;
+}
+
 void xhci_mem_cleanup(struct xhci_hcd *xhci)
 {
 	struct pci_dev	*pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
@@ -593,6 +690,7 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci)
 
 	xhci->page_size = 0;
 	xhci->page_shift = 0;
+	scratchpad_free(xhci);
 }
 
 int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
@@ -755,7 +853,11 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
 	for (i = 0; i < MAX_HC_SLOTS; ++i)
 		xhci->devs[i] = 0;
 
+	if (scratchpad_alloc(xhci, flags))
+		goto fail;
+
 	return 0;
+
 fail:
 	xhci_warn(xhci, "Couldn't initialize memory\n");
 	xhci_mem_cleanup(xhci);
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 074728e1022..5a09b9a26e0 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -89,6 +89,7 @@ struct xhci_cap_regs {
 #define HCS_ERST_MAX(p)		(((p) >> 4) & 0xf)
 /* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
 /* bits 27:31 number of Scratchpad buffers SW must allocate for the HW */
+#define HCS_MAX_SCRATCHPAD(p)   (((p) >> 27) & 0x1f)
 
 /* HCSPARAMS3 - hcs_params3 - bitmasks */
 /* bits 0:7, Max U1 to U0 latency for the roothub ports */
@@ -951,6 +952,13 @@ struct xhci_erst {
 	unsigned int		erst_size;
 };
 
+struct xhci_scratchpad {
+	u64 *sp_array;
+	dma_addr_t sp_dma;
+	void **sp_buffers;
+	dma_addr_t *sp_dma_buffers;
+};
+
 /*
  * Each segment table entry is 4*32bits long.  1K seems like an ok size:
  * (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table,
@@ -1005,6 +1013,9 @@ struct xhci_hcd {
 	struct xhci_ring	*cmd_ring;
 	struct xhci_ring	*event_ring;
 	struct xhci_erst	erst;
+	/* Scratchpad */
+	struct xhci_scratchpad  *scratchpad;
+
 	/* slot enabling and address device helpers */
 	struct completion	addr_dev;
 	int slot_id;
-- 
GitLab


From 28c2d2efb48dec2f0b050affae6d5787d6449e47 Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:05:08 -0700
Subject: [PATCH 0192/1153] USB: xhci: Always align output device contexts to
 64 bytes.

Make sure the xHCI output device context is 64-byte aligned.  Previous
code was using the same structure for both the output device context and
the input control context.  Since the structure had 32 bytes of flags
before the device context, the output device context wouldn't be 64-byte
aligned.  Define a new structure to use for the output device context and
clean up the debugging for these two structures.

The copy of the device context in the input control context does *not*
need to be 64-byte aligned.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-dbg.c | 101 ++++++++++++++++++++++--------------
 drivers/usb/host/xhci-hcd.c |   7 +--
 drivers/usb/host/xhci-mem.c |  15 +++---
 drivers/usb/host/xhci.h     |  19 ++++++-
 4 files changed, 89 insertions(+), 53 deletions(-)

diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c
index 6d62e4abe3c..d77f8de1125 100644
--- a/drivers/usb/host/xhci-dbg.c
+++ b/drivers/usb/host/xhci-dbg.c
@@ -393,78 +393,103 @@ void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci)
 			upper_32_bits(val));
 }
 
-void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep)
+dma_addr_t xhci_dbg_slot_ctx(struct xhci_hcd *xhci, struct xhci_slot_ctx *slot, dma_addr_t dma)
 {
-	int i, j;
-	int last_ep_ctx = 31;
 	/* Fields are 32 bits wide, DMA addresses are in bytes */
 	int field_size = 32 / 8;
-
-	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n",
-			&ctx->drop_flags, (unsigned long long)dma,
-			ctx->drop_flags);
-	dma += field_size;
-	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n",
-			&ctx->add_flags, (unsigned long long)dma,
-			ctx->add_flags);
-	dma += field_size;
-	for (i = 0; i < 6; ++i) {
-		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
-				&ctx->rsvd[i], (unsigned long long)dma,
-				ctx->rsvd[i], i);
-		dma += field_size;
-	}
+	int i;
 
 	xhci_dbg(xhci, "Slot Context:\n");
 	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info\n",
-			&ctx->slot.dev_info,
-			(unsigned long long)dma, ctx->slot.dev_info);
+			&slot->dev_info,
+			(unsigned long long)dma, slot->dev_info);
 	dma += field_size;
 	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info2\n",
-			&ctx->slot.dev_info2,
-			(unsigned long long)dma, ctx->slot.dev_info2);
+			&slot->dev_info2,
+			(unsigned long long)dma, slot->dev_info2);
 	dma += field_size;
 	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tt_info\n",
-			&ctx->slot.tt_info,
-			(unsigned long long)dma, ctx->slot.tt_info);
+			&slot->tt_info,
+			(unsigned long long)dma, slot->tt_info);
 	dma += field_size;
 	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_state\n",
-			&ctx->slot.dev_state,
-			(unsigned long long)dma, ctx->slot.dev_state);
+			&slot->dev_state,
+			(unsigned long long)dma, slot->dev_state);
 	dma += field_size;
 	for (i = 0; i < 4; ++i) {
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
-				&ctx->slot.reserved[i], (unsigned long long)dma,
-				ctx->slot.reserved[i], i);
+				&slot->reserved[i], (unsigned long long)dma,
+				slot->reserved[i], i);
 		dma += field_size;
 	}
 
+	return dma;
+}
+
+dma_addr_t xhci_dbg_ep_ctx(struct xhci_hcd *xhci, struct xhci_ep_ctx *ep, dma_addr_t dma, unsigned int last_ep)
+{
+	int i, j;
+	int last_ep_ctx = 31;
+	/* Fields are 32 bits wide, DMA addresses are in bytes */
+	int field_size = 32 / 8;
+
 	if (last_ep < 31)
 		last_ep_ctx = last_ep + 1;
 	for (i = 0; i < last_ep_ctx; ++i) {
 		xhci_dbg(xhci, "Endpoint %02d Context:\n", i);
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info\n",
-				&ctx->ep[i].ep_info,
-				(unsigned long long)dma, ctx->ep[i].ep_info);
+				&ep[i].ep_info,
+				(unsigned long long)dma, ep[i].ep_info);
 		dma += field_size;
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info2\n",
-				&ctx->ep[i].ep_info2,
-				(unsigned long long)dma, ctx->ep[i].ep_info2);
+				&ep[i].ep_info2,
+				(unsigned long long)dma, ep[i].ep_info2);
 		dma += field_size;
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08llx - deq\n",
-				&ctx->ep[i].deq,
-				(unsigned long long)dma, ctx->ep[i].deq);
+				&ep[i].deq,
+				(unsigned long long)dma, ep[i].deq);
 		dma += 2*field_size;
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tx_info\n",
-				&ctx->ep[i].tx_info,
-				(unsigned long long)dma, ctx->ep[i].tx_info);
+				&ep[i].tx_info,
+				(unsigned long long)dma, ep[i].tx_info);
 		dma += field_size;
 		for (j = 0; j < 3; ++j) {
 			xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
-					&ctx->ep[i].reserved[j],
+					&ep[i].reserved[j],
 					(unsigned long long)dma,
-					ctx->ep[i].reserved[j], j);
+					ep[i].reserved[j], j);
 			dma += field_size;
 		}
 	}
+	return dma;
+}
+
+void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep)
+{
+	int i;
+	/* Fields are 32 bits wide, DMA addresses are in bytes */
+	int field_size = 32 / 8;
+
+	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n",
+			&ctx->drop_flags, (unsigned long long)dma,
+			ctx->drop_flags);
+	dma += field_size;
+	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n",
+			&ctx->add_flags, (unsigned long long)dma,
+			ctx->add_flags);
+	dma += field_size;
+	for (i = 0; i < 6; ++i) {
+		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
+				&ctx->rsvd[i], (unsigned long long)dma,
+				ctx->rsvd[i], i);
+		dma += field_size;
+	}
+	dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma);
+	dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep);
+}
+
+void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep)
+{
+	dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma);
+	dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep);
 }
diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c
index 008326d5bc5..921dd173d79 100644
--- a/drivers/usb/host/xhci-hcd.c
+++ b/drivers/usb/host/xhci-hcd.c
@@ -1013,7 +1013,7 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	}
 
 	xhci_dbg(xhci, "Output context after successful config ep cmd:\n");
-	xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma,
+	xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma,
 			LAST_CTX_TO_EP_NUM(virt_dev->in_ctx->slot.dev_info));
 
 	xhci_zero_in_ctx(virt_dev);
@@ -1265,7 +1265,7 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 	xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id);
 	xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2);
 	xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id);
-	xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2);
+	xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2);
 	/*
 	 * USB core uses address 1 for the roothubs, so we add one to the
 	 * address given back to us by the HC.
@@ -1274,9 +1274,6 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 	/* Zero the input context control for later use */
 	virt_dev->in_ctx->add_flags = 0;
 	virt_dev->in_ctx->drop_flags = 0;
-	/* Mirror flags in the output context for future ep enable/disable */
-	virt_dev->out_ctx->add_flags = SLOT_FLAG | EP0_FLAG;
-	virt_dev->out_ctx->drop_flags = 0;
 
 	xhci_dbg(xhci, "Device address = %d\n", udev->devnum);
 	/* XXX Meh, not sure if anyone else but choose_address uses this. */
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index 71121d99235..8d6bdf2f801 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -235,7 +235,10 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id,
 		return 0;
 	dev = xhci->devs[slot_id];
 
-	/* Allocate the (output) device context that will be used in the HC */
+	/* Allocate the (output) device context that will be used in the HC.
+	 * The structure is 32 bytes smaller than the input context, but that's
+	 * fine.
+	 */
 	dev->out_ctx = dma_pool_alloc(xhci->device_pool, flags, &dma);
 	if (!dev->out_ctx)
 		goto fail;
@@ -260,16 +263,12 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id,
 
 	init_completion(&dev->cmd_completion);
 
-	/*
-	 * Point to output device context in dcbaa; skip the output control
-	 * context, which is eight 32 bit fields (or 32 bytes long)
-	 */
-	xhci->dcbaa->dev_context_ptrs[slot_id] =
-		(u32) dev->out_ctx_dma + (32);
+	/* Point to output device context in dcbaa. */
+	xhci->dcbaa->dev_context_ptrs[slot_id] = dev->out_ctx_dma;
 	xhci_dbg(xhci, "Set slot id %d dcbaa entry %p to 0x%llx\n",
 			slot_id,
 			&xhci->dcbaa->dev_context_ptrs[slot_id],
-			(unsigned long long)dev->out_ctx_dma);
+			(unsigned long long) xhci->dcbaa->dev_context_ptrs[slot_id]);
 
 	return 1;
 fail:
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 5a09b9a26e0..d4d3c7777fb 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -584,15 +584,29 @@ struct xhci_ep_ctx {
 
 /**
  * struct xhci_device_control
- * Input/Output context; see section 6.2.5.
+ * Input context; see section 6.2.5.
  *
  * @drop_context:	set the bit of the endpoint context you want to disable
  * @add_context:	set the bit of the endpoint context you want to enable
  */
 struct xhci_device_control {
+	/* Input control context */
 	u32	drop_flags;
 	u32	add_flags;
 	u32	rsvd[6];
+	/* Copy of device context */
+	struct xhci_slot_ctx	slot;
+	struct xhci_ep_ctx	ep[31];
+};
+
+/**
+ * struct xhci_device_ctx
+ * Device context; see section 6.2.1.
+ *
+ * @slot:		slot context for the device.
+ * @ep:			array of endpoint contexts for the device.
+ */
+struct xhci_device_ctx {
 	struct xhci_slot_ctx	slot;
 	struct xhci_ep_ctx	ep[31];
 };
@@ -612,7 +626,7 @@ struct xhci_virt_device {
 	 * track of input and output contexts separately because
 	 * these commands might fail and we don't trust the hardware.
 	 */
-	struct xhci_device_control	*out_ctx;
+	struct xhci_device_ctx		*out_ctx;
 	dma_addr_t			out_ctx_dma;
 	/* Used for addressing devices and configuration changes */
 	struct xhci_device_control	*in_ctx;
@@ -1126,6 +1140,7 @@ void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst);
 void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci);
 void xhci_dbg_ring_ptrs(struct xhci_hcd *xhci, struct xhci_ring *ring);
 void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep);
+void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep);
 
 /* xHCI memory managment */
 void xhci_mem_cleanup(struct xhci_hcd *xhci);
-- 
GitLab


From d115b04818e57bdbc7ccde4d0660b15e33013dc8 Mon Sep 17 00:00:00 2001
From: John Youn <johnyoun@synopsys.com>
Date: Mon, 27 Jul 2009 12:05:15 -0700
Subject: [PATCH 0193/1153] USB: xhci: Support for 64-byte contexts

Adds support for controllers that use 64-byte contexts.  The following context
data structures are affected by this: Device, Input, Input Control, Endpoint,
and Slot.  To accommodate the use of either 32 or 64-byte contexts, a Device or
Input context can only be accessed through functions which look-up and return
pointers to their contained contexts.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-dbg.c  | 125 ++++++++++++++++++++++-------------
 drivers/usb/host/xhci-hcd.c  | 121 +++++++++++++++++++--------------
 drivers/usb/host/xhci-mem.c  | 121 +++++++++++++++++++++++----------
 drivers/usb/host/xhci-ring.c |  22 ++++--
 drivers/usb/host/xhci.h      |  61 +++++++++--------
 5 files changed, 287 insertions(+), 163 deletions(-)

diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c
index d77f8de1125..705e3432415 100644
--- a/drivers/usb/host/xhci-dbg.c
+++ b/drivers/usb/host/xhci-dbg.c
@@ -393,103 +393,138 @@ void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci)
 			upper_32_bits(val));
 }
 
-dma_addr_t xhci_dbg_slot_ctx(struct xhci_hcd *xhci, struct xhci_slot_ctx *slot, dma_addr_t dma)
+/* Print the last 32 bytes for 64-byte contexts */
+static void dbg_rsvd64(struct xhci_hcd *xhci, u64 *ctx, dma_addr_t dma)
+{
+	int i;
+	for (i = 0; i < 4; ++i) {
+		xhci_dbg(xhci, "@%p (virt) @%08llx "
+			 "(dma) %#08llx - rsvd64[%d]\n",
+			 &ctx[4 + i], (unsigned long long)dma,
+			 ctx[4 + i], i);
+		dma += 8;
+	}
+}
+
+void xhci_dbg_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx)
 {
 	/* Fields are 32 bits wide, DMA addresses are in bytes */
 	int field_size = 32 / 8;
 	int i;
 
+	struct xhci_slot_ctx *slot_ctx = xhci_get_slot_ctx(xhci, ctx);
+	dma_addr_t dma = ctx->dma + ((unsigned long)slot_ctx - (unsigned long)ctx);
+	int csz = HCC_64BYTE_CONTEXT(xhci->hcc_params);
+
 	xhci_dbg(xhci, "Slot Context:\n");
 	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info\n",
-			&slot->dev_info,
-			(unsigned long long)dma, slot->dev_info);
+			&slot_ctx->dev_info,
+			(unsigned long long)dma, slot_ctx->dev_info);
 	dma += field_size;
 	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_info2\n",
-			&slot->dev_info2,
-			(unsigned long long)dma, slot->dev_info2);
+			&slot_ctx->dev_info2,
+			(unsigned long long)dma, slot_ctx->dev_info2);
 	dma += field_size;
 	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tt_info\n",
-			&slot->tt_info,
-			(unsigned long long)dma, slot->tt_info);
+			&slot_ctx->tt_info,
+			(unsigned long long)dma, slot_ctx->tt_info);
 	dma += field_size;
 	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - dev_state\n",
-			&slot->dev_state,
-			(unsigned long long)dma, slot->dev_state);
+			&slot_ctx->dev_state,
+			(unsigned long long)dma, slot_ctx->dev_state);
 	dma += field_size;
 	for (i = 0; i < 4; ++i) {
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
-				&slot->reserved[i], (unsigned long long)dma,
-				slot->reserved[i], i);
+				&slot_ctx->reserved[i], (unsigned long long)dma,
+				slot_ctx->reserved[i], i);
 		dma += field_size;
 	}
 
-	return dma;
+	if (csz)
+		dbg_rsvd64(xhci, (u64 *)slot_ctx, dma);
 }
 
-dma_addr_t xhci_dbg_ep_ctx(struct xhci_hcd *xhci, struct xhci_ep_ctx *ep, dma_addr_t dma, unsigned int last_ep)
+void xhci_dbg_ep_ctx(struct xhci_hcd *xhci,
+		     struct xhci_container_ctx *ctx,
+		     unsigned int last_ep)
 {
 	int i, j;
 	int last_ep_ctx = 31;
 	/* Fields are 32 bits wide, DMA addresses are in bytes */
 	int field_size = 32 / 8;
+	int csz = HCC_64BYTE_CONTEXT(xhci->hcc_params);
 
 	if (last_ep < 31)
 		last_ep_ctx = last_ep + 1;
 	for (i = 0; i < last_ep_ctx; ++i) {
+		struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, ctx, i);
+		dma_addr_t dma = ctx->dma +
+			((unsigned long)ep_ctx - (unsigned long)ctx);
+
 		xhci_dbg(xhci, "Endpoint %02d Context:\n", i);
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info\n",
-				&ep[i].ep_info,
-				(unsigned long long)dma, ep[i].ep_info);
+				&ep_ctx->ep_info,
+				(unsigned long long)dma, ep_ctx->ep_info);
 		dma += field_size;
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - ep_info2\n",
-				&ep[i].ep_info2,
-				(unsigned long long)dma, ep[i].ep_info2);
+				&ep_ctx->ep_info2,
+				(unsigned long long)dma, ep_ctx->ep_info2);
 		dma += field_size;
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08llx - deq\n",
-				&ep[i].deq,
-				(unsigned long long)dma, ep[i].deq);
+				&ep_ctx->deq,
+				(unsigned long long)dma, ep_ctx->deq);
 		dma += 2*field_size;
 		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - tx_info\n",
-				&ep[i].tx_info,
-				(unsigned long long)dma, ep[i].tx_info);
+				&ep_ctx->tx_info,
+				(unsigned long long)dma, ep_ctx->tx_info);
 		dma += field_size;
 		for (j = 0; j < 3; ++j) {
 			xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
-					&ep[i].reserved[j],
+					&ep_ctx->reserved[j],
 					(unsigned long long)dma,
-					ep[i].reserved[j], j);
+					ep_ctx->reserved[j], j);
 			dma += field_size;
 		}
+
+		if (csz)
+			dbg_rsvd64(xhci, (u64 *)ep_ctx, dma);
 	}
-	return dma;
 }
 
-void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep)
+void xhci_dbg_ctx(struct xhci_hcd *xhci,
+		  struct xhci_container_ctx *ctx,
+		  unsigned int last_ep)
 {
 	int i;
 	/* Fields are 32 bits wide, DMA addresses are in bytes */
 	int field_size = 32 / 8;
-
-	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n",
-			&ctx->drop_flags, (unsigned long long)dma,
-			ctx->drop_flags);
-	dma += field_size;
-	xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n",
-			&ctx->add_flags, (unsigned long long)dma,
-			ctx->add_flags);
-	dma += field_size;
-	for (i = 0; i < 6; ++i) {
-		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd[%d]\n",
-				&ctx->rsvd[i], (unsigned long long)dma,
-				ctx->rsvd[i], i);
+	struct xhci_slot_ctx *slot_ctx;
+	dma_addr_t dma = ctx->dma;
+	int csz = HCC_64BYTE_CONTEXT(xhci->hcc_params);
+
+	if (ctx->type == XHCI_CTX_TYPE_INPUT) {
+		struct xhci_input_control_ctx *ctrl_ctx =
+			xhci_get_input_control_ctx(xhci, ctx);
+		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - drop flags\n",
+			 &ctrl_ctx->drop_flags, (unsigned long long)dma,
+			 ctrl_ctx->drop_flags);
 		dma += field_size;
+		xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - add flags\n",
+			 &ctrl_ctx->add_flags, (unsigned long long)dma,
+			 ctrl_ctx->add_flags);
+		dma += field_size;
+		for (i = 0; i < 6; ++i) {
+			xhci_dbg(xhci, "@%p (virt) @%08llx (dma) %#08x - rsvd2[%d]\n",
+				 &ctrl_ctx->rsvd2[i], (unsigned long long)dma,
+				 ctrl_ctx->rsvd2[i], i);
+			dma += field_size;
+		}
+
+		if (csz)
+			dbg_rsvd64(xhci, (u64 *)ctrl_ctx, dma);
 	}
-	dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma);
-	dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep);
-}
 
-void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep)
-{
-	dma = xhci_dbg_slot_ctx(xhci, &ctx->slot, dma);
-	dma = xhci_dbg_ep_ctx(xhci, ctx->ep, dma, last_ep);
+	slot_ctx = xhci_get_slot_ctx(xhci, ctx);
+	xhci_dbg_slot_ctx(xhci, ctx);
+	xhci_dbg_ep_ctx(xhci, ctx, last_ep);
 }
diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c
index 921dd173d79..057a07e876b 100644
--- a/drivers/usb/host/xhci-hcd.c
+++ b/drivers/usb/host/xhci-hcd.c
@@ -722,7 +722,9 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 		struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd *xhci;
-	struct xhci_device_control *in_ctx;
+	struct xhci_container_ctx *in_ctx, *out_ctx;
+	struct xhci_input_control_ctx *ctrl_ctx;
+	struct xhci_slot_ctx *slot_ctx;
 	unsigned int last_ctx;
 	unsigned int ep_index;
 	struct xhci_ep_ctx *ep_ctx;
@@ -750,31 +752,34 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 	}
 
 	in_ctx = xhci->devs[udev->slot_id]->in_ctx;
+	out_ctx = xhci->devs[udev->slot_id]->out_ctx;
+	ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx);
 	ep_index = xhci_get_endpoint_index(&ep->desc);
-	ep_ctx = &xhci->devs[udev->slot_id]->out_ctx->ep[ep_index];
+	ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index);
 	/* If the HC already knows the endpoint is disabled,
 	 * or the HCD has noted it is disabled, ignore this request
 	 */
 	if ((ep_ctx->ep_info & EP_STATE_MASK) == EP_STATE_DISABLED ||
-			in_ctx->drop_flags & xhci_get_endpoint_flag(&ep->desc)) {
+			ctrl_ctx->drop_flags & xhci_get_endpoint_flag(&ep->desc)) {
 		xhci_warn(xhci, "xHCI %s called with disabled ep %p\n",
 				__func__, ep);
 		return 0;
 	}
 
-	in_ctx->drop_flags |= drop_flag;
-	new_drop_flags = in_ctx->drop_flags;
+	ctrl_ctx->drop_flags |= drop_flag;
+	new_drop_flags = ctrl_ctx->drop_flags;
 
-	in_ctx->add_flags = ~drop_flag;
-	new_add_flags = in_ctx->add_flags;
+	ctrl_ctx->add_flags = ~drop_flag;
+	new_add_flags = ctrl_ctx->add_flags;
 
-	last_ctx = xhci_last_valid_endpoint(in_ctx->add_flags);
+	last_ctx = xhci_last_valid_endpoint(ctrl_ctx->add_flags);
+	slot_ctx = xhci_get_slot_ctx(xhci, in_ctx);
 	/* Update the last valid endpoint context, if we deleted the last one */
-	if ((in_ctx->slot.dev_info & LAST_CTX_MASK) > LAST_CTX(last_ctx)) {
-		in_ctx->slot.dev_info &= ~LAST_CTX_MASK;
-		in_ctx->slot.dev_info |= LAST_CTX(last_ctx);
+	if ((slot_ctx->dev_info & LAST_CTX_MASK) > LAST_CTX(last_ctx)) {
+		slot_ctx->dev_info &= ~LAST_CTX_MASK;
+		slot_ctx->dev_info |= LAST_CTX(last_ctx);
 	}
-	new_slot_info = in_ctx->slot.dev_info;
+	new_slot_info = slot_ctx->dev_info;
 
 	xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
 
@@ -804,9 +809,11 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 		struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd *xhci;
-	struct xhci_device_control *in_ctx;
+	struct xhci_container_ctx *in_ctx, *out_ctx;
 	unsigned int ep_index;
 	struct xhci_ep_ctx *ep_ctx;
+	struct xhci_slot_ctx *slot_ctx;
+	struct xhci_input_control_ctx *ctrl_ctx;
 	u32 added_ctxs;
 	unsigned int last_ctx;
 	u32 new_add_flags, new_drop_flags, new_slot_info;
@@ -839,12 +846,14 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 	}
 
 	in_ctx = xhci->devs[udev->slot_id]->in_ctx;
+	out_ctx = xhci->devs[udev->slot_id]->out_ctx;
+	ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx);
 	ep_index = xhci_get_endpoint_index(&ep->desc);
-	ep_ctx = &xhci->devs[udev->slot_id]->out_ctx->ep[ep_index];
+	ep_ctx = xhci_get_ep_ctx(xhci, out_ctx, ep_index);
 	/* If the HCD has already noted the endpoint is enabled,
 	 * ignore this request.
 	 */
-	if (in_ctx->add_flags & xhci_get_endpoint_flag(&ep->desc)) {
+	if (ctrl_ctx->add_flags & xhci_get_endpoint_flag(&ep->desc)) {
 		xhci_warn(xhci, "xHCI %s called with enabled ep %p\n",
 				__func__, ep);
 		return 0;
@@ -862,8 +871,8 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 		return -ENOMEM;
 	}
 
-	in_ctx->add_flags |= added_ctxs;
-	new_add_flags = in_ctx->add_flags;
+	ctrl_ctx->add_flags |= added_ctxs;
+	new_add_flags = ctrl_ctx->add_flags;
 
 	/* If xhci_endpoint_disable() was called for this endpoint, but the
 	 * xHC hasn't been notified yet through the check_bandwidth() call,
@@ -871,14 +880,15 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 	 * descriptors.  We must drop and re-add this endpoint, so we leave the
 	 * drop flags alone.
 	 */
-	new_drop_flags = in_ctx->drop_flags;
+	new_drop_flags = ctrl_ctx->drop_flags;
 
+	slot_ctx = xhci_get_slot_ctx(xhci, in_ctx);
 	/* Update the last valid endpoint context, if we just added one past */
-	if ((in_ctx->slot.dev_info & LAST_CTX_MASK) < LAST_CTX(last_ctx)) {
-		in_ctx->slot.dev_info &= ~LAST_CTX_MASK;
-		in_ctx->slot.dev_info |= LAST_CTX(last_ctx);
+	if ((slot_ctx->dev_info & LAST_CTX_MASK) < LAST_CTX(last_ctx)) {
+		slot_ctx->dev_info &= ~LAST_CTX_MASK;
+		slot_ctx->dev_info |= LAST_CTX(last_ctx);
 	}
-	new_slot_info = in_ctx->slot.dev_info;
+	new_slot_info = slot_ctx->dev_info;
 
 	/* Store the usb_device pointer for later use */
 	ep->hcpriv = udev;
@@ -892,9 +902,11 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 	return 0;
 }
 
-static void xhci_zero_in_ctx(struct xhci_virt_device *virt_dev)
+static void xhci_zero_in_ctx(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev)
 {
+	struct xhci_input_control_ctx *ctrl_ctx;
 	struct xhci_ep_ctx *ep_ctx;
+	struct xhci_slot_ctx *slot_ctx;
 	int i;
 
 	/* When a device's add flag and drop flag are zero, any subsequent
@@ -902,13 +914,15 @@ static void xhci_zero_in_ctx(struct xhci_virt_device *virt_dev)
 	 * untouched.  Make sure we don't leave any old state in the input
 	 * endpoint contexts.
 	 */
-	virt_dev->in_ctx->drop_flags = 0;
-	virt_dev->in_ctx->add_flags = 0;
-	virt_dev->in_ctx->slot.dev_info &= ~LAST_CTX_MASK;
+	ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx);
+	ctrl_ctx->drop_flags = 0;
+	ctrl_ctx->add_flags = 0;
+	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
+	slot_ctx->dev_info &= ~LAST_CTX_MASK;
 	/* Endpoint 0 is always valid */
-	virt_dev->in_ctx->slot.dev_info |= LAST_CTX(1);
+	slot_ctx->dev_info |= LAST_CTX(1);
 	for (i = 1; i < 31; ++i) {
-		ep_ctx = &virt_dev->in_ctx->ep[i];
+		ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, i);
 		ep_ctx->ep_info = 0;
 		ep_ctx->ep_info2 = 0;
 		ep_ctx->deq = 0;
@@ -934,6 +948,8 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	unsigned long flags;
 	struct xhci_hcd *xhci;
 	struct xhci_virt_device	*virt_dev;
+	struct xhci_input_control_ctx *ctrl_ctx;
+	struct xhci_slot_ctx *slot_ctx;
 
 	ret = xhci_check_args(hcd, udev, NULL, 0, __func__);
 	if (ret <= 0)
@@ -949,16 +965,18 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	virt_dev = xhci->devs[udev->slot_id];
 
 	/* See section 4.6.6 - A0 = 1; A1 = D0 = D1 = 0 */
-	virt_dev->in_ctx->add_flags |= SLOT_FLAG;
-	virt_dev->in_ctx->add_flags &= ~EP0_FLAG;
-	virt_dev->in_ctx->drop_flags &= ~SLOT_FLAG;
-	virt_dev->in_ctx->drop_flags &= ~EP0_FLAG;
+	ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx);
+	ctrl_ctx->add_flags |= SLOT_FLAG;
+	ctrl_ctx->add_flags &= ~EP0_FLAG;
+	ctrl_ctx->drop_flags &= ~SLOT_FLAG;
+	ctrl_ctx->drop_flags &= ~EP0_FLAG;
 	xhci_dbg(xhci, "New Input Control Context:\n");
-	xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma,
-			LAST_CTX_TO_EP_NUM(virt_dev->in_ctx->slot.dev_info));
+	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
+	xhci_dbg_ctx(xhci, virt_dev->in_ctx,
+			LAST_CTX_TO_EP_NUM(slot_ctx->dev_info));
 
 	spin_lock_irqsave(&xhci->lock, flags);
-	ret = xhci_queue_configure_endpoint(xhci, virt_dev->in_ctx_dma,
+	ret = xhci_queue_configure_endpoint(xhci, virt_dev->in_ctx->dma,
 			udev->slot_id);
 	if (ret < 0) {
 		spin_unlock_irqrestore(&xhci->lock, flags);
@@ -1013,10 +1031,10 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	}
 
 	xhci_dbg(xhci, "Output context after successful config ep cmd:\n");
-	xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma,
-			LAST_CTX_TO_EP_NUM(virt_dev->in_ctx->slot.dev_info));
+	xhci_dbg_ctx(xhci, virt_dev->out_ctx,
+			LAST_CTX_TO_EP_NUM(slot_ctx->dev_info));
 
-	xhci_zero_in_ctx(virt_dev);
+	xhci_zero_in_ctx(xhci, virt_dev);
 	/* Free any old rings */
 	for (i = 1; i < 31; ++i) {
 		if (virt_dev->new_ep_rings[i]) {
@@ -1054,7 +1072,7 @@ void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 			virt_dev->new_ep_rings[i] = NULL;
 		}
 	}
-	xhci_zero_in_ctx(virt_dev);
+	xhci_zero_in_ctx(xhci, virt_dev);
 }
 
 /* Deal with stalled endpoints.  The core should have sent the control message
@@ -1187,6 +1205,8 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 	struct xhci_virt_device *virt_dev;
 	int ret = 0;
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+	struct xhci_slot_ctx *slot_ctx;
+	struct xhci_input_control_ctx *ctrl_ctx;
 	u64 temp_64;
 
 	if (!udev->slot_id) {
@@ -1201,11 +1221,11 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 		xhci_setup_addressable_virt_dev(xhci, udev);
 	/* Otherwise, assume the core has the device configured how it wants */
 	xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id);
-	xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2);
+	xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2);
 
 	spin_lock_irqsave(&xhci->lock, flags);
-	ret = xhci_queue_address_device(xhci, virt_dev->in_ctx_dma,
-			udev->slot_id);
+	ret = xhci_queue_address_device(xhci, virt_dev->in_ctx->dma,
+					udev->slot_id);
 	if (ret) {
 		spin_unlock_irqrestore(&xhci->lock, flags);
 		xhci_dbg(xhci, "FIXME: allocate a command ring segment\n");
@@ -1246,7 +1266,7 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 		xhci_err(xhci, "ERROR: unexpected command completion "
 				"code 0x%x.\n", virt_dev->cmd_status);
 		xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id);
-		xhci_dbg_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2);
+		xhci_dbg_ctx(xhci, virt_dev->out_ctx, 2);
 		ret = -EINVAL;
 		break;
 	}
@@ -1261,19 +1281,21 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 			(unsigned long long)
 				xhci->dcbaa->dev_context_ptrs[udev->slot_id]);
 	xhci_dbg(xhci, "Output Context DMA address = %#08llx\n",
-			(unsigned long long)virt_dev->out_ctx_dma);
+			(unsigned long long)virt_dev->out_ctx->dma);
 	xhci_dbg(xhci, "Slot ID %d Input Context:\n", udev->slot_id);
-	xhci_dbg_ctx(xhci, virt_dev->in_ctx, virt_dev->in_ctx_dma, 2);
+	xhci_dbg_ctx(xhci, virt_dev->in_ctx, 2);
 	xhci_dbg(xhci, "Slot ID %d Output Context:\n", udev->slot_id);
-	xhci_dbg_device_ctx(xhci, virt_dev->out_ctx, virt_dev->out_ctx_dma, 2);
+	xhci_dbg_ctx(xhci, virt_dev->out_ctx, 2);
 	/*
 	 * USB core uses address 1 for the roothubs, so we add one to the
 	 * address given back to us by the HC.
 	 */
-	udev->devnum = (virt_dev->out_ctx->slot.dev_state & DEV_ADDR_MASK) + 1;
+	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx);
+	udev->devnum = (slot_ctx->dev_state & DEV_ADDR_MASK) + 1;
 	/* Zero the input context control for later use */
-	virt_dev->in_ctx->add_flags = 0;
-	virt_dev->in_ctx->drop_flags = 0;
+	ctrl_ctx = xhci_get_input_control_ctx(xhci, virt_dev->in_ctx);
+	ctrl_ctx->add_flags = 0;
+	ctrl_ctx->drop_flags = 0;
 
 	xhci_dbg(xhci, "Device address = %d\n", udev->devnum);
 	/* XXX Meh, not sure if anyone else but choose_address uses this. */
@@ -1315,7 +1337,6 @@ static int __init xhci_hcd_init(void)
 	/* xhci_device_control has eight fields, and also
 	 * embeds one xhci_slot_ctx and 31 xhci_ep_ctx
 	 */
-	BUILD_BUG_ON(sizeof(struct xhci_device_control) != (8+8+8*31)*32/8);
 	BUILD_BUG_ON(sizeof(struct xhci_stream_ctx) != 4*32/8);
 	BUILD_BUG_ON(sizeof(union xhci_trb) != 4*32/8);
 	BUILD_BUG_ON(sizeof(struct xhci_erst_entry) != 4*32/8);
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index 8d6bdf2f801..e6b9a1c6002 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -189,6 +189,63 @@ fail:
 	return 0;
 }
 
+#define CTX_SIZE(_hcc) (HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32)
+
+struct xhci_container_ctx *xhci_alloc_container_ctx(struct xhci_hcd *xhci,
+						    int type, gfp_t flags)
+{
+	struct xhci_container_ctx *ctx = kzalloc(sizeof(*ctx), flags);
+	if (!ctx)
+		return NULL;
+
+	BUG_ON((type != XHCI_CTX_TYPE_DEVICE) && (type != XHCI_CTX_TYPE_INPUT));
+	ctx->type = type;
+	ctx->size = HCC_64BYTE_CONTEXT(xhci->hcc_params) ? 2048 : 1024;
+	if (type == XHCI_CTX_TYPE_INPUT)
+		ctx->size += CTX_SIZE(xhci->hcc_params);
+
+	ctx->bytes = dma_pool_alloc(xhci->device_pool, flags, &ctx->dma);
+	memset(ctx->bytes, 0, ctx->size);
+	return ctx;
+}
+
+void xhci_free_container_ctx(struct xhci_hcd *xhci,
+			     struct xhci_container_ctx *ctx)
+{
+	dma_pool_free(xhci->device_pool, ctx->bytes, ctx->dma);
+	kfree(ctx);
+}
+
+struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_hcd *xhci,
+					      struct xhci_container_ctx *ctx)
+{
+	BUG_ON(ctx->type != XHCI_CTX_TYPE_INPUT);
+	return (struct xhci_input_control_ctx *)ctx->bytes;
+}
+
+struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci,
+					struct xhci_container_ctx *ctx)
+{
+	if (ctx->type == XHCI_CTX_TYPE_DEVICE)
+		return (struct xhci_slot_ctx *)ctx->bytes;
+
+	return (struct xhci_slot_ctx *)
+		(ctx->bytes + CTX_SIZE(xhci->hcc_params));
+}
+
+struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci,
+				    struct xhci_container_ctx *ctx,
+				    unsigned int ep_index)
+{
+	/* increment ep index by offset of start of ep ctx array */
+	ep_index++;
+	if (ctx->type == XHCI_CTX_TYPE_INPUT)
+		ep_index++;
+
+	return (struct xhci_ep_ctx *)
+		(ctx->bytes + (ep_index * CTX_SIZE(xhci->hcc_params)));
+}
+
 /* All the xhci_tds in the ring's TD list should be freed at this point */
 void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id)
 {
@@ -209,11 +266,10 @@ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id)
 			xhci_ring_free(xhci, dev->ep_rings[i]);
 
 	if (dev->in_ctx)
-		dma_pool_free(xhci->device_pool,
-				dev->in_ctx, dev->in_ctx_dma);
+		xhci_free_container_ctx(xhci, dev->in_ctx);
 	if (dev->out_ctx)
-		dma_pool_free(xhci->device_pool,
-				dev->out_ctx, dev->out_ctx_dma);
+		xhci_free_container_ctx(xhci, dev->out_ctx);
+
 	kfree(xhci->devs[slot_id]);
 	xhci->devs[slot_id] = 0;
 }
@@ -221,7 +277,6 @@ void xhci_free_virt_device(struct xhci_hcd *xhci, int slot_id)
 int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id,
 		struct usb_device *udev, gfp_t flags)
 {
-	dma_addr_t	dma;
 	struct xhci_virt_device *dev;
 
 	/* Slot ID 0 is reserved */
@@ -235,26 +290,21 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id,
 		return 0;
 	dev = xhci->devs[slot_id];
 
-	/* Allocate the (output) device context that will be used in the HC.
-	 * The structure is 32 bytes smaller than the input context, but that's
-	 * fine.
-	 */
-	dev->out_ctx = dma_pool_alloc(xhci->device_pool, flags, &dma);
+	/* Allocate the (output) device context that will be used in the HC. */
+	dev->out_ctx = xhci_alloc_container_ctx(xhci, XHCI_CTX_TYPE_DEVICE, flags);
 	if (!dev->out_ctx)
 		goto fail;
-	dev->out_ctx_dma = dma;
+
 	xhci_dbg(xhci, "Slot %d output ctx = 0x%llx (dma)\n", slot_id,
-			(unsigned long long)dma);
-	memset(dev->out_ctx, 0, sizeof(*dev->out_ctx));
+			(unsigned long long)dev->out_ctx->dma);
 
 	/* Allocate the (input) device context for address device command */
-	dev->in_ctx = dma_pool_alloc(xhci->device_pool, flags, &dma);
+	dev->in_ctx = xhci_alloc_container_ctx(xhci, XHCI_CTX_TYPE_INPUT, flags);
 	if (!dev->in_ctx)
 		goto fail;
-	dev->in_ctx_dma = dma;
+
 	xhci_dbg(xhci, "Slot %d input ctx = 0x%llx (dma)\n", slot_id,
-			(unsigned long long)dma);
-	memset(dev->in_ctx, 0, sizeof(*dev->in_ctx));
+			(unsigned long long)dev->in_ctx->dma);
 
 	/* Allocate endpoint 0 ring */
 	dev->ep_rings[0] = xhci_ring_alloc(xhci, 1, true, flags);
@@ -264,7 +314,7 @@ int xhci_alloc_virt_device(struct xhci_hcd *xhci, int slot_id,
 	init_completion(&dev->cmd_completion);
 
 	/* Point to output device context in dcbaa. */
-	xhci->dcbaa->dev_context_ptrs[slot_id] = dev->out_ctx_dma;
+	xhci->dcbaa->dev_context_ptrs[slot_id] = dev->out_ctx->dma;
 	xhci_dbg(xhci, "Set slot id %d dcbaa entry %p to 0x%llx\n",
 			slot_id,
 			&xhci->dcbaa->dev_context_ptrs[slot_id],
@@ -282,6 +332,8 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud
 	struct xhci_virt_device *dev;
 	struct xhci_ep_ctx	*ep0_ctx;
 	struct usb_device	*top_dev;
+	struct xhci_slot_ctx    *slot_ctx;
+	struct xhci_input_control_ctx *ctrl_ctx;
 
 	dev = xhci->devs[udev->slot_id];
 	/* Slot ID 0 is reserved */
@@ -290,27 +342,29 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud
 				udev->slot_id);
 		return -EINVAL;
 	}
-	ep0_ctx = &dev->in_ctx->ep[0];
+	ep0_ctx = xhci_get_ep_ctx(xhci, dev->in_ctx, 0);
+	ctrl_ctx = xhci_get_input_control_ctx(xhci, dev->in_ctx);
+	slot_ctx = xhci_get_slot_ctx(xhci, dev->in_ctx);
 
 	/* 2) New slot context and endpoint 0 context are valid*/
-	dev->in_ctx->add_flags = SLOT_FLAG | EP0_FLAG;
+	ctrl_ctx->add_flags = SLOT_FLAG | EP0_FLAG;
 
 	/* 3) Only the control endpoint is valid - one endpoint context */
-	dev->in_ctx->slot.dev_info |= LAST_CTX(1);
+	slot_ctx->dev_info |= LAST_CTX(1);
 
 	switch (udev->speed) {
 	case USB_SPEED_SUPER:
-		dev->in_ctx->slot.dev_info |= (u32) udev->route;
-		dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_SS;
+		slot_ctx->dev_info |= (u32) udev->route;
+		slot_ctx->dev_info |= (u32) SLOT_SPEED_SS;
 		break;
 	case USB_SPEED_HIGH:
-		dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_HS;
+		slot_ctx->dev_info |= (u32) SLOT_SPEED_HS;
 		break;
 	case USB_SPEED_FULL:
-		dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_FS;
+		slot_ctx->dev_info |= (u32) SLOT_SPEED_FS;
 		break;
 	case USB_SPEED_LOW:
-		dev->in_ctx->slot.dev_info |= (u32) SLOT_SPEED_LS;
+		slot_ctx->dev_info |= (u32) SLOT_SPEED_LS;
 		break;
 	case USB_SPEED_VARIABLE:
 		xhci_dbg(xhci, "FIXME xHCI doesn't support wireless speeds\n");
@@ -324,7 +378,7 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud
 	for (top_dev = udev; top_dev->parent && top_dev->parent->parent;
 			top_dev = top_dev->parent)
 		/* Found device below root hub */;
-	dev->in_ctx->slot.dev_info2 |= (u32) ROOT_HUB_PORT(top_dev->portnum);
+	slot_ctx->dev_info2 |= (u32) ROOT_HUB_PORT(top_dev->portnum);
 	xhci_dbg(xhci, "Set root hub portnum to %d\n", top_dev->portnum);
 
 	/* Is this a LS/FS device under a HS hub? */
@@ -334,8 +388,8 @@ int xhci_setup_addressable_virt_dev(struct xhci_hcd *xhci, struct usb_device *ud
 	 */
 	if ((udev->speed == USB_SPEED_LOW || udev->speed == USB_SPEED_FULL) &&
 			udev->tt) {
-		dev->in_ctx->slot.tt_info = udev->tt->hub->slot_id;
-		dev->in_ctx->slot.tt_info |= udev->ttport << 8;
+		slot_ctx->tt_info = udev->tt->hub->slot_id;
+		slot_ctx->tt_info |= udev->ttport << 8;
 	}
 	xhci_dbg(xhci, "udev->tt = %p\n", udev->tt);
 	xhci_dbg(xhci, "udev->ttport = 0x%x\n", udev->ttport);
@@ -466,7 +520,7 @@ int xhci_endpoint_init(struct xhci_hcd *xhci,
 	unsigned int max_burst;
 
 	ep_index = xhci_get_endpoint_index(&ep->desc);
-	ep_ctx = &virt_dev->in_ctx->ep[ep_index];
+	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
 
 	/* Set up the endpoint ring */
 	virt_dev->new_ep_rings[ep_index] = xhci_ring_alloc(xhci, 1, true, mem_flags);
@@ -533,7 +587,7 @@ void xhci_endpoint_zero(struct xhci_hcd *xhci,
 	struct xhci_ep_ctx *ep_ctx;
 
 	ep_index = xhci_get_endpoint_index(&ep->desc);
-	ep_ctx = &virt_dev->in_ctx->ep[ep_index];
+	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
 
 	ep_ctx->ep_info = 0;
 	ep_ctx->ep_info2 = 0;
@@ -753,11 +807,10 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
 	 */
 	xhci->segment_pool = dma_pool_create("xHCI ring segments", dev,
 			SEGMENT_SIZE, 64, xhci->page_size);
+
 	/* See Table 46 and Note on Figure 55 */
-	/* FIXME support 64-byte contexts */
 	xhci->device_pool = dma_pool_create("xHCI input/output contexts", dev,
-			sizeof(struct xhci_device_control),
-			64, xhci->page_size);
+			2112, 64, xhci->page_size);
 	if (!xhci->segment_pool || !xhci->device_pool)
 		goto fail;
 
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 0903e98989e..ea31753c313 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -362,6 +362,7 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci,
 	struct xhci_virt_device *dev = xhci->devs[slot_id];
 	struct xhci_ring *ep_ring = dev->ep_rings[ep_index];
 	struct xhci_generic_trb *trb;
+	struct xhci_ep_ctx *ep_ctx;
 
 	state->new_cycle_state = 0;
 	state->new_deq_seg = find_trb_seg(cur_td->start_seg,
@@ -370,7 +371,8 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci,
 	if (!state->new_deq_seg)
 		BUG();
 	/* Dig out the cycle state saved by the xHC during the stop ep cmd */
-	state->new_cycle_state = 0x1 & dev->out_ctx->ep[ep_index].deq;
+	ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index);
+	state->new_cycle_state = 0x1 & ep_ctx->deq;
 
 	state->new_deq_ptr = cur_td->last_trb;
 	state->new_deq_seg = find_trb_seg(state->new_deq_seg,
@@ -570,11 +572,15 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci,
 	unsigned int ep_index;
 	struct xhci_ring *ep_ring;
 	struct xhci_virt_device *dev;
+	struct xhci_ep_ctx *ep_ctx;
+	struct xhci_slot_ctx *slot_ctx;
 
 	slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]);
 	ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]);
 	dev = xhci->devs[slot_id];
 	ep_ring = dev->ep_rings[ep_index];
+	ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index);
+	slot_ctx = xhci_get_slot_ctx(xhci, dev->out_ctx);
 
 	if (GET_COMP_CODE(event->status) != COMP_SUCCESS) {
 		unsigned int ep_state;
@@ -588,9 +594,9 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci,
 		case COMP_CTX_STATE:
 			xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed due "
 					"to incorrect slot or ep state.\n");
-			ep_state = dev->out_ctx->ep[ep_index].ep_info;
+			ep_state = ep_ctx->ep_info;
 			ep_state &= EP_STATE_MASK;
-			slot_state = dev->out_ctx->slot.dev_state;
+			slot_state = slot_ctx->dev_state;
 			slot_state = GET_SLOT_STATE(slot_state);
 			xhci_dbg(xhci, "Slot state = %u, EP state = %u\n",
 					slot_state, ep_state);
@@ -613,7 +619,7 @@ static void handle_set_deq_completion(struct xhci_hcd *xhci,
 		 */
 	} else {
 		xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq = @%08llx\n",
-				dev->out_ctx->ep[ep_index].deq);
+				ep_ctx->deq);
 	}
 
 	ep_ring->state &= ~SET_DEQ_PENDING;
@@ -795,6 +801,7 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 	union xhci_trb *event_trb;
 	struct urb *urb = 0;
 	int status = -EINPROGRESS;
+	struct xhci_ep_ctx *ep_ctx;
 
 	xhci_dbg(xhci, "In %s\n", __func__);
 	xdev = xhci->devs[TRB_TO_SLOT_ID(event->flags)];
@@ -807,7 +814,8 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 	ep_index = TRB_TO_EP_ID(event->flags) - 1;
 	xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index);
 	ep_ring = xdev->ep_rings[ep_index];
-	if (!ep_ring || (xdev->out_ctx->ep[ep_index].ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) {
+	ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
+	if (!ep_ring || (ep_ctx->ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) {
 		xhci_err(xhci, "ERROR Transfer event pointed to disabled endpoint\n");
 		return -ENODEV;
 	}
@@ -1193,9 +1201,9 @@ static int prepare_transfer(struct xhci_hcd *xhci,
 		gfp_t mem_flags)
 {
 	int ret;
-
+	struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
 	ret = prepare_ring(xhci, xdev->ep_rings[ep_index],
-			xdev->out_ctx->ep[ep_index].ep_info & EP_STATE_MASK,
+			ep_ctx->ep_info & EP_STATE_MASK,
 			num_trbs, mem_flags);
 	if (ret)
 		return ret;
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index d4d3c7777fb..9c108c63270 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -446,6 +446,27 @@ struct xhci_doorbell_array {
 #define EPI_TO_DB(p)		(((p) + 1) & 0xff)
 
 
+/**
+ * struct xhci_container_ctx
+ * @type: Type of context.  Used to calculated offsets to contained contexts.
+ * @size: Size of the context data
+ * @bytes: The raw context data given to HW
+ * @dma: dma address of the bytes
+ *
+ * Represents either a Device or Input context.  Holds a pointer to the raw
+ * memory used for the context (bytes) and dma address of it (dma).
+ */
+struct xhci_container_ctx {
+	unsigned type;
+#define XHCI_CTX_TYPE_DEVICE  0x1
+#define XHCI_CTX_TYPE_INPUT   0x2
+
+	int size;
+
+	u8 *bytes;
+	dma_addr_t dma;
+};
+
 /**
  * struct xhci_slot_ctx
  * @dev_info:	Route string, device speed, hub info, and last valid endpoint
@@ -583,32 +604,16 @@ struct xhci_ep_ctx {
 
 
 /**
- * struct xhci_device_control
- * Input context; see section 6.2.5.
+ * struct xhci_input_control_context
+ * Input control context; see section 6.2.5.
  *
  * @drop_context:	set the bit of the endpoint context you want to disable
  * @add_context:	set the bit of the endpoint context you want to enable
  */
-struct xhci_device_control {
-	/* Input control context */
+struct xhci_input_control_ctx {
 	u32	drop_flags;
 	u32	add_flags;
-	u32	rsvd[6];
-	/* Copy of device context */
-	struct xhci_slot_ctx	slot;
-	struct xhci_ep_ctx	ep[31];
-};
-
-/**
- * struct xhci_device_ctx
- * Device context; see section 6.2.1.
- *
- * @slot:		slot context for the device.
- * @ep:			array of endpoint contexts for the device.
- */
-struct xhci_device_ctx {
-	struct xhci_slot_ctx	slot;
-	struct xhci_ep_ctx	ep[31];
+	u32	rsvd2[6];
 };
 
 /* drop context bitmasks */
@@ -616,7 +621,6 @@ struct xhci_device_ctx {
 /* add context bitmasks */
 #define	ADD_EP(x)	(0x1 << x)
 
-
 struct xhci_virt_device {
 	/*
 	 * Commands to the hardware are passed an "input context" that
@@ -626,11 +630,10 @@ struct xhci_virt_device {
 	 * track of input and output contexts separately because
 	 * these commands might fail and we don't trust the hardware.
 	 */
-	struct xhci_device_ctx		*out_ctx;
-	dma_addr_t			out_ctx_dma;
+	struct xhci_container_ctx       *out_ctx;
 	/* Used for addressing devices and configuration changes */
-	struct xhci_device_control	*in_ctx;
-	dma_addr_t			in_ctx_dma;
+	struct xhci_container_ctx       *in_ctx;
+
 	/* FIXME when stream support is added */
 	struct xhci_ring		*ep_rings[31];
 	/* Temporary storage in case the configure endpoint command fails and we
@@ -1139,8 +1142,7 @@ void xhci_debug_ring(struct xhci_hcd *xhci, struct xhci_ring *ring);
 void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst);
 void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci);
 void xhci_dbg_ring_ptrs(struct xhci_hcd *xhci, struct xhci_ring *ring);
-void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep);
-void xhci_dbg_device_ctx(struct xhci_hcd *xhci, struct xhci_device_ctx *ctx, dma_addr_t dma, unsigned int last_ep);
+void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int last_ep);
 
 /* xHCI memory managment */
 void xhci_mem_cleanup(struct xhci_hcd *xhci);
@@ -1207,4 +1209,9 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex,
 		char *buf, u16 wLength);
 int xhci_hub_status_data(struct usb_hcd *hcd, char *buf);
 
+/* xHCI contexts */
+struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx);
+struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx);
+struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int ep_index);
+
 #endif /* __LINUX_XHCI_HCD_H */
-- 
GitLab


From c92bcfa7b4038d8ffe1f02e21269f18eb0b64144 Mon Sep 17 00:00:00 2001
From: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Date: Mon, 27 Jul 2009 12:05:21 -0700
Subject: [PATCH 0194/1153] USB: xhci: Stall handling bug fixes.

Correct the xHCI code to handle stalls on USB endpoints.  We need to move
the endpoint ring's dequeue pointer past the stalled transfer, or the HW
will try to restart the transfer the next time the doorbell is rung.

Don't attempt to clear a halt on an endpoint if we haven't seen a stalled
transfer for it.  The USB core will attempt to clear a halt on all
endpoints when it selects a new configuration.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/xhci-hcd.c  |  24 +++++++
 drivers/usb/host/xhci-ring.c | 133 ++++++++++++++++++++++-------------
 drivers/usb/host/xhci.h      |  12 ++++
 3 files changed, 120 insertions(+), 49 deletions(-)

diff --git a/drivers/usb/host/xhci-hcd.c b/drivers/usb/host/xhci-hcd.c
index 057a07e876b..816c39caca1 100644
--- a/drivers/usb/host/xhci-hcd.c
+++ b/drivers/usb/host/xhci-hcd.c
@@ -1089,6 +1089,8 @@ void xhci_endpoint_reset(struct usb_hcd *hcd,
 	unsigned int ep_index;
 	unsigned long flags;
 	int ret;
+	struct xhci_dequeue_state deq_state;
+	struct xhci_ring *ep_ring;
 
 	xhci = hcd_to_xhci(hcd);
 	udev = (struct usb_device *) ep->hcpriv;
@@ -1098,11 +1100,33 @@ void xhci_endpoint_reset(struct usb_hcd *hcd,
 	if (!ep->hcpriv)
 		return;
 	ep_index = xhci_get_endpoint_index(&ep->desc);
+	ep_ring = xhci->devs[udev->slot_id]->ep_rings[ep_index];
+	if (!ep_ring->stopped_td) {
+		xhci_dbg(xhci, "Endpoint 0x%x not halted, refusing to reset.\n",
+				ep->desc.bEndpointAddress);
+		return;
+	}
 
 	xhci_dbg(xhci, "Queueing reset endpoint command\n");
 	spin_lock_irqsave(&xhci->lock, flags);
 	ret = xhci_queue_reset_ep(xhci, udev->slot_id, ep_index);
+	/*
+	 * Can't change the ring dequeue pointer until it's transitioned to the
+	 * stopped state, which is only upon a successful reset endpoint
+	 * command.  Better hope that last command worked!
+	 */
 	if (!ret) {
+		xhci_dbg(xhci, "Cleaning up stalled endpoint ring\n");
+		/* We need to move the HW's dequeue pointer past this TD,
+		 * or it will attempt to resend it on the next doorbell ring.
+		 */
+		xhci_find_new_dequeue_state(xhci, udev->slot_id,
+				ep_index, ep_ring->stopped_td, &deq_state);
+		xhci_dbg(xhci, "Queueing new dequeue state\n");
+		xhci_queue_new_dequeue_state(xhci, ep_ring,
+				udev->slot_id,
+				ep_index, &deq_state);
+		kfree(ep_ring->stopped_td);
 		xhci_ring_cmd_db(xhci);
 	}
 	spin_unlock_irqrestore(&xhci->lock, flags);
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index ea31753c313..aa88a067148 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -335,12 +335,6 @@ static struct xhci_segment *find_trb_seg(
 	return cur_seg;
 }
 
-struct dequeue_state {
-	struct xhci_segment *new_deq_seg;
-	union xhci_trb *new_deq_ptr;
-	int new_cycle_state;
-};
-
 /*
  * Move the xHC's endpoint ring dequeue pointer past cur_td.
  * Record the new state of the xHC's endpoint ring dequeue segment,
@@ -355,26 +349,30 @@ struct dequeue_state {
  *  - Finally we move the dequeue state one TRB further, toggling the cycle bit
  *    if we've moved it past a link TRB with the toggle cycle bit set.
  */
-static void find_new_dequeue_state(struct xhci_hcd *xhci,
+void xhci_find_new_dequeue_state(struct xhci_hcd *xhci,
 		unsigned int slot_id, unsigned int ep_index,
-		struct xhci_td *cur_td, struct dequeue_state *state)
+		struct xhci_td *cur_td, struct xhci_dequeue_state *state)
 {
 	struct xhci_virt_device *dev = xhci->devs[slot_id];
 	struct xhci_ring *ep_ring = dev->ep_rings[ep_index];
 	struct xhci_generic_trb *trb;
 	struct xhci_ep_ctx *ep_ctx;
+	dma_addr_t addr;
 
 	state->new_cycle_state = 0;
+	xhci_dbg(xhci, "Finding segment containing stopped TRB.\n");
 	state->new_deq_seg = find_trb_seg(cur_td->start_seg,
 			ep_ring->stopped_trb,
 			&state->new_cycle_state);
 	if (!state->new_deq_seg)
 		BUG();
 	/* Dig out the cycle state saved by the xHC during the stop ep cmd */
+	xhci_dbg(xhci, "Finding endpoint context\n");
 	ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index);
 	state->new_cycle_state = 0x1 & ep_ctx->deq;
 
 	state->new_deq_ptr = cur_td->last_trb;
+	xhci_dbg(xhci, "Finding segment containing last TRB in TD.\n");
 	state->new_deq_seg = find_trb_seg(state->new_deq_seg,
 			state->new_deq_ptr,
 			&state->new_cycle_state);
@@ -388,6 +386,12 @@ static void find_new_dequeue_state(struct xhci_hcd *xhci,
 	next_trb(xhci, ep_ring, &state->new_deq_seg, &state->new_deq_ptr);
 
 	/* Don't update the ring cycle state for the producer (us). */
+	xhci_dbg(xhci, "New dequeue segment = %p (virtual)\n",
+			state->new_deq_seg);
+	addr = xhci_trb_virt_to_dma(state->new_deq_seg, state->new_deq_ptr);
+	xhci_dbg(xhci, "New dequeue pointer = 0x%llx (DMA)\n",
+			(unsigned long long) addr);
+	xhci_dbg(xhci, "Setting dequeue pointer in internal ring state.\n");
 	ep_ring->dequeue = state->new_deq_ptr;
 	ep_ring->deq_seg = state->new_deq_seg;
 }
@@ -437,6 +441,30 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id,
 		unsigned int ep_index, struct xhci_segment *deq_seg,
 		union xhci_trb *deq_ptr, u32 cycle_state);
 
+void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci,
+		struct xhci_ring *ep_ring, unsigned int slot_id,
+		unsigned int ep_index, struct xhci_dequeue_state *deq_state)
+{
+	xhci_dbg(xhci, "Set TR Deq Ptr cmd, new deq seg = %p (0x%llx dma), "
+			"new deq ptr = %p (0x%llx dma), new cycle = %u\n",
+			deq_state->new_deq_seg,
+			(unsigned long long)deq_state->new_deq_seg->dma,
+			deq_state->new_deq_ptr,
+			(unsigned long long)xhci_trb_virt_to_dma(deq_state->new_deq_seg, deq_state->new_deq_ptr),
+			deq_state->new_cycle_state);
+	queue_set_tr_deq(xhci, slot_id, ep_index,
+			deq_state->new_deq_seg,
+			deq_state->new_deq_ptr,
+			(u32) deq_state->new_cycle_state);
+	/* Stop the TD queueing code from ringing the doorbell until
+	 * this command completes.  The HC won't set the dequeue pointer
+	 * if the ring is running, and ringing the doorbell starts the
+	 * ring running.
+	 */
+	ep_ring->state |= SET_DEQ_PENDING;
+	xhci_ring_cmd_db(xhci);
+}
+
 /*
  * When we get a command completion for a Stop Endpoint Command, we need to
  * unlink any cancelled TDs from the ring.  There are two ways to do that:
@@ -457,7 +485,7 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci,
 	struct xhci_td *cur_td = 0;
 	struct xhci_td *last_unlinked_td;
 
-	struct dequeue_state deq_state;
+	struct xhci_dequeue_state deq_state;
 #ifdef CONFIG_USB_HCD_STAT
 	ktime_t stop_time = ktime_get();
 #endif
@@ -485,7 +513,7 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci,
 		 * move the xHC endpoint ring dequeue pointer past this TD.
 		 */
 		if (cur_td == ep_ring->stopped_td)
-			find_new_dequeue_state(xhci, slot_id, ep_index, cur_td,
+			xhci_find_new_dequeue_state(xhci, slot_id, ep_index, cur_td,
 					&deq_state);
 		else
 			td_to_noop(xhci, ep_ring, cur_td);
@@ -501,24 +529,8 @@ static void handle_stopped_endpoint(struct xhci_hcd *xhci,
 
 	/* If necessary, queue a Set Transfer Ring Dequeue Pointer command */
 	if (deq_state.new_deq_ptr && deq_state.new_deq_seg) {
-		xhci_dbg(xhci, "Set TR Deq Ptr cmd, new deq seg = %p (0x%llx dma), "
-				"new deq ptr = %p (0x%llx dma), new cycle = %u\n",
-				deq_state.new_deq_seg,
-				(unsigned long long)deq_state.new_deq_seg->dma,
-				deq_state.new_deq_ptr,
-				(unsigned long long)xhci_trb_virt_to_dma(deq_state.new_deq_seg, deq_state.new_deq_ptr),
-				deq_state.new_cycle_state);
-		queue_set_tr_deq(xhci, slot_id, ep_index,
-				deq_state.new_deq_seg,
-				deq_state.new_deq_ptr,
-				(u32) deq_state.new_cycle_state);
-		/* Stop the TD queueing code from ringing the doorbell until
-		 * this command completes.  The HC won't set the dequeue pointer
-		 * if the ring is running, and ringing the doorbell starts the
-		 * ring running.
-		 */
-		ep_ring->state |= SET_DEQ_PENDING;
-		xhci_ring_cmd_db(xhci);
+		xhci_queue_new_dequeue_state(xhci, ep_ring,
+				slot_id, ep_index, &deq_state);
 	} else {
 		/* Otherwise just ring the doorbell to restart the ring */
 		ring_ep_doorbell(xhci, slot_id, ep_index);
@@ -929,12 +941,15 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 		if (event_trb != ep_ring->dequeue) {
 			/* The event was for the status stage */
 			if (event_trb == td->last_trb) {
-				/* Did we already see a short data stage? */
-				if (td->urb->actual_length != 0)
-					status = -EREMOTEIO;
-				else
+				if (td->urb->actual_length != 0) {
+					/* Don't overwrite a previously set error code */
+					if (status == -EINPROGRESS || status == 0)
+						/* Did we already see a short data stage? */
+						status = -EREMOTEIO;
+				} else {
 					td->urb->actual_length =
 						td->urb->transfer_buffer_length;
+				}
 			} else {
 			/* Maybe the event was for the data stage? */
 				if (GET_COMP_CODE(event->transfer_len) != COMP_STOP_INVAL) {
@@ -992,16 +1007,20 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 							TRB_LEN(event->transfer_len));
 					td->urb->actual_length = 0;
 				}
-				if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
-					status = -EREMOTEIO;
-				else
-					status = 0;
+				/* Don't overwrite a previously set error code */
+				if (status == -EINPROGRESS) {
+					if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
+						status = -EREMOTEIO;
+					else
+						status = 0;
+				}
 			} else {
 				td->urb->actual_length = td->urb->transfer_buffer_length;
 				/* Ignore a short packet completion if the
 				 * untransferred length was zero.
 				 */
-				status = 0;
+				if (status == -EREMOTEIO)
+					status = 0;
 			}
 		} else {
 			/* Slow path - walk the list, starting from the dequeue
@@ -1028,19 +1047,30 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 					TRB_LEN(event->transfer_len);
 		}
 	}
-	/* The Endpoint Stop Command completion will take care of
-	 * any stopped TDs.  A stopped TD may be restarted, so don't update the
-	 * ring dequeue pointer or take this TD off any lists yet.
-	 */
 	if (GET_COMP_CODE(event->transfer_len) == COMP_STOP_INVAL ||
 			GET_COMP_CODE(event->transfer_len) == COMP_STOP) {
+		/* The Endpoint Stop Command completion will take care of any
+		 * stopped TDs.  A stopped TD may be restarted, so don't update
+		 * the ring dequeue pointer or take this TD off any lists yet.
+		 */
 		ep_ring->stopped_td = td;
 		ep_ring->stopped_trb = event_trb;
 	} else {
-		/* Update ring dequeue pointer */
-		while (ep_ring->dequeue != td->last_trb)
+		if (GET_COMP_CODE(event->transfer_len) == COMP_STALL) {
+			/* The transfer is completed from the driver's
+			 * perspective, but we need to issue a set dequeue
+			 * command for this stalled endpoint to move the dequeue
+			 * pointer past the TD.  We can't do that here because
+			 * the halt condition must be cleared first.
+			 */
+			ep_ring->stopped_td = td;
+			ep_ring->stopped_trb = event_trb;
+		} else {
+			/* Update ring dequeue pointer */
+			while (ep_ring->dequeue != td->last_trb)
+				inc_deq(xhci, ep_ring, false);
 			inc_deq(xhci, ep_ring, false);
-		inc_deq(xhci, ep_ring, false);
+		}
 
 		/* Clean up the endpoint's TD list */
 		urb = td->urb;
@@ -1050,7 +1080,10 @@ static int handle_tx_event(struct xhci_hcd *xhci,
 			list_del(&td->cancelled_td_list);
 			ep_ring->cancels_pending--;
 		}
-		kfree(td);
+		/* Leave the TD around for the reset endpoint function to use */
+		if (GET_COMP_CODE(event->transfer_len) != COMP_STALL) {
+			kfree(td);
+		}
 		urb->hcpriv = NULL;
 	}
 cleanup:
@@ -1166,13 +1199,13 @@ static int prepare_ring(struct xhci_hcd *xhci, struct xhci_ring *ep_ring,
 		 */
 		xhci_warn(xhci, "WARN urb submitted to disabled ep\n");
 		return -ENOENT;
-	case EP_STATE_HALTED:
 	case EP_STATE_ERROR:
-		xhci_warn(xhci, "WARN waiting for halt or error on ep "
-				"to be cleared\n");
+		xhci_warn(xhci, "WARN waiting for error on ep to be cleared\n");
 		/* FIXME event handling code for error needs to clear it */
 		/* XXX not sure if this should be -ENOENT or not */
 		return -EINVAL;
+	case EP_STATE_HALTED:
+		xhci_dbg(xhci, "WARN halted endpoint, queueing URB anyway.\n");
 	case EP_STATE_STOPPED:
 	case EP_STATE_RUNNING:
 		break;
@@ -1724,10 +1757,12 @@ static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id,
 	u32 type = TRB_TYPE(TRB_SET_DEQ);
 
 	addr = xhci_trb_virt_to_dma(deq_seg, deq_ptr);
-	if (addr == 0)
+	if (addr == 0) {
 		xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n");
 		xhci_warn(xhci, "WARN deq seg = %p, deq pt = %p\n",
 				deq_seg, deq_ptr);
+		return 0;
+	}
 	return queue_command(xhci, lower_32_bits(addr) | cycle_state,
 			upper_32_bits(addr), 0,
 			trb_slot_id | trb_ep_index | type);
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index 9c108c63270..d31d32206ba 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -952,6 +952,12 @@ struct xhci_ring {
 	u32			cycle_state;
 };
 
+struct xhci_dequeue_state {
+	struct xhci_segment *new_deq_seg;
+	union xhci_trb *new_deq_ptr;
+	int new_cycle_state;
+};
+
 struct xhci_erst_entry {
 	/* 64-bit event ring segment address */
 	u64	seg_addr;
@@ -1203,6 +1209,12 @@ int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
 		u32 slot_id);
 int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id,
 		unsigned int ep_index);
+void xhci_find_new_dequeue_state(struct xhci_hcd *xhci,
+		unsigned int slot_id, unsigned int ep_index,
+		struct xhci_td *cur_td, struct xhci_dequeue_state *state);
+void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci,
+		struct xhci_ring *ep_ring, unsigned int slot_id,
+		unsigned int ep_index, struct xhci_dequeue_state *deq_state);
 
 /* xHCI roothub code */
 int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex,
-- 
GitLab


From 044dcc824a167e3d39ba69a49e2b723dd10678f6 Mon Sep 17 00:00:00 2001
From: Wolfram Sang <w.sang@pengutronix.de>
Date: Sun, 26 Jul 2009 18:27:29 +0200
Subject: [PATCH 0195/1153] pata_pcmcia: add CNF-CDROM-ID

Fixes this report:
http://article.gmane.org/gmane.linux.kernel.pcmcia.devel/2228/

Reported-by: John McGrath <john@john-mcgrath.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/pata_pcmcia.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/ata/pata_pcmcia.c b/drivers/ata/pata_pcmcia.c
index f4d009ed50a..dc99e26f8e5 100644
--- a/drivers/ata/pata_pcmcia.c
+++ b/drivers/ata/pata_pcmcia.c
@@ -411,6 +411,7 @@ static struct pcmcia_device_id pcmcia_devices[] = {
 	PCMCIA_DEVICE_PROD_ID123("PCMCIA", "IDE CARD", "F1", 0x281f1c5d, 0x1907960c, 0xf7fde8b9),
 	PCMCIA_DEVICE_PROD_ID12("ARGOSY", "CD-ROM", 0x78f308dc, 0x66536591),
 	PCMCIA_DEVICE_PROD_ID12("ARGOSY", "PnPIDE", 0x78f308dc, 0x0c694728),
+	PCMCIA_DEVICE_PROD_ID12("CNF   ", "CD-ROM", 0x46d7db81, 0x66536591),
 	PCMCIA_DEVICE_PROD_ID12("CNF CD-M", "CD-ROM", 0x7d93b852, 0x66536591),
 	PCMCIA_DEVICE_PROD_ID12("Creative Technology Ltd.", "PCMCIA CD-ROM Interface Card", 0xff8c8a45, 0xfe8020c4),
 	PCMCIA_DEVICE_PROD_ID12("Digital Equipment Corporation.", "Digital Mobile Media CD-ROM", 0x17692a66, 0xef1dcbde),
-- 
GitLab


From 705d201414382b0966d7c903d738dfdb9380e4af Mon Sep 17 00:00:00 2001
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Sun, 26 Jul 2009 16:21:01 +0200
Subject: [PATCH 0196/1153] libata: add missing NULL pointer check to
 ata_eh_reset()

drivers/ata/libata-eh.c +2403 ata_eh_reset(80) warning: variable derefenced before check 'slave'

Please note that this is _not_ a real bug at the moment since ata_eh_context
structure is embedded into ata_list structure and the code alwas checks for
'slave' before accessing 'sehc'.

Anyway lets add missing check and always have a valid 'sehc' pointer (which
makes code easier to understand and prevents introducing some possible bugs
in the future).

Reported-by: Dan Carpenter <error27@gmail.com>
Cc: corbet@lwn.net
Cc: eteo@redhat.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/libata-eh.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 1a07c061f64..79711b64054 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -2327,7 +2327,7 @@ int ata_eh_reset(struct ata_link *link, int classify,
 	struct ata_port *ap = link->ap;
 	struct ata_link *slave = ap->slave_link;
 	struct ata_eh_context *ehc = &link->eh_context;
-	struct ata_eh_context *sehc = &slave->eh_context;
+	struct ata_eh_context *sehc = slave ? &slave->eh_context : NULL;
 	unsigned int *classes = ehc->classes;
 	unsigned int lflags = link->flags;
 	int verbose = !(ehc->i.flags & ATA_EHI_QUIET);
-- 
GitLab


From c9abde12d6debe5b97f36fb43cf188c1b9cd477f Mon Sep 17 00:00:00 2001
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Sun, 26 Jul 2009 16:05:13 +0200
Subject: [PATCH 0197/1153] libata: remove superfluous NULL pointer checks

host->ports[] always contain pointers to valid port structures since
a "dummy port" structure is used in case if there is no physical port.

This patch takes care of two entries from Dan's list:

drivers/ata/sata_sil.c +535 sil_interrupt(13) warning: variable derefenced before check 'ap'
drivers/ata/sata_mv.c +2517 mv_unexpected_intr(6) warning: variable derefenced before check 'ap'

and of another needless NULL pointer check in pata_octeon_cf.c.

Reported-by: Dan Carpenter <error27@gmail.com>
Cc: corbet@lwn.net
Cc: eteo@redhat.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/pata_octeon_cf.c | 3 ++-
 drivers/ata/sata_mv.c        | 2 +-
 drivers/ata/sata_sil.c       | 2 +-
 3 files changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/ata/pata_octeon_cf.c b/drivers/ata/pata_octeon_cf.c
index 8d9343accf3..abdd19fe990 100644
--- a/drivers/ata/pata_octeon_cf.c
+++ b/drivers/ata/pata_octeon_cf.c
@@ -653,7 +653,8 @@ static irqreturn_t octeon_cf_interrupt(int irq, void *dev_instance)
 
 		ap = host->ports[i];
 		ocd = ap->dev->platform_data;
-		if (!ap || (ap->flags & ATA_FLAG_DISABLED))
+
+		if (ap->flags & ATA_FLAG_DISABLED)
 			continue;
 
 		ocd = ap->dev->platform_data;
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 23714aefb82..c19417e0220 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -2514,7 +2514,7 @@ static void mv_unexpected_intr(struct ata_port *ap, int edma_was_enabled)
 	char *when = "idle";
 
 	ata_ehi_clear_desc(ehi);
-	if (!ap || (ap->flags & ATA_FLAG_DISABLED)) {
+	if (ap->flags & ATA_FLAG_DISABLED) {
 		when = "disabled";
 	} else if (edma_was_enabled) {
 		when = "EDMA enabled";
diff --git a/drivers/ata/sata_sil.c b/drivers/ata/sata_sil.c
index 030ec079b18..35bd5cc7f28 100644
--- a/drivers/ata/sata_sil.c
+++ b/drivers/ata/sata_sil.c
@@ -532,7 +532,7 @@ static irqreturn_t sil_interrupt(int irq, void *dev_instance)
 		struct ata_port *ap = host->ports[i];
 		u32 bmdma2 = readl(mmio_base + sil_port[ap->port_no].bmdma2);
 
-		if (unlikely(!ap || ap->flags & ATA_FLAG_DISABLED))
+		if (unlikely(ap->flags & ATA_FLAG_DISABLED))
 			continue;
 
 		/* turn off SATA_IRQ if not supported */
-- 
GitLab


From c1f57d9b9846e7366c328f916d1a82d03ba4312c Mon Sep 17 00:00:00 2001
From: David Milburn <dmilburn@redhat.com>
Date: Wed, 22 Jul 2009 15:15:56 -0500
Subject: [PATCH 0198/1153] ahci: add device IDs for Ibex Peak ahci controllers

Add device IDS for Ibex Peak SATA AHCI Controllers

Signed-off-by: Jaroslav Kysela <jkysela@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/ahci.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 336eb1ed73c..958c1fa4190 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -515,10 +515,14 @@ static const struct pci_device_id ahci_pci_tbl[] = {
 	{ PCI_VDEVICE(INTEL, 0x3a05), board_ahci }, /* ICH10 */
 	{ PCI_VDEVICE(INTEL, 0x3a22), board_ahci }, /* ICH10 */
 	{ PCI_VDEVICE(INTEL, 0x3a25), board_ahci }, /* ICH10 */
+	{ PCI_VDEVICE(INTEL, 0x3b22), board_ahci }, /* PCH AHCI */
+	{ PCI_VDEVICE(INTEL, 0x3b23), board_ahci }, /* PCH AHCI */
 	{ PCI_VDEVICE(INTEL, 0x3b24), board_ahci }, /* PCH RAID */
 	{ PCI_VDEVICE(INTEL, 0x3b25), board_ahci }, /* PCH RAID */
+	{ PCI_VDEVICE(INTEL, 0x3b29), board_ahci }, /* PCH AHCI */
 	{ PCI_VDEVICE(INTEL, 0x3b2b), board_ahci }, /* PCH RAID */
 	{ PCI_VDEVICE(INTEL, 0x3b2c), board_ahci }, /* PCH RAID */
+	{ PCI_VDEVICE(INTEL, 0x3b2f), board_ahci }, /* PCH AHCI */
 
 	/* JMicron 360/1/3/5/6, match class to avoid IDE function */
 	{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
-- 
GitLab


From 6034734d333c1bd01119a5b480b34a507a3adf56 Mon Sep 17 00:00:00 2001
From: Steve Conklin <sconklin@canonical.com>
Date: Thu, 16 Jul 2009 16:27:56 -0500
Subject: [PATCH 0199/1153] ata_piix: Add new laptop short cable IDs

OriginalAuthor: Michael Frey <michael.frey@canonical.com>
Signed-off-by: Steve Conklin <sconklin@canonical.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/ata_piix.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index d0a14cf2bd7..deada1fe6a0 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -596,9 +596,11 @@ static const struct ich_laptop ich_laptop[] = {
 	{ 0x27DF, 0x0005, 0x0280 },	/* ICH7 on Acer 5602WLMi */
 	{ 0x27DF, 0x1025, 0x0102 },	/* ICH7 on Acer 5602aWLMi */
 	{ 0x27DF, 0x1025, 0x0110 },	/* ICH7 on Acer 3682WLMi */
+	{ 0x27DF, 0x1028, 0x02b0 },	/* ICH7 on unknown Dell */
 	{ 0x27DF, 0x1043, 0x1267 },	/* ICH7 on Asus W5F */
 	{ 0x27DF, 0x103C, 0x30A1 },	/* ICH7 on HP Compaq nc2400 */
 	{ 0x27DF, 0x1071, 0xD221 },	/* ICH7 on Hercules EC-900 */
+	{ 0x27DF, 0x152D, 0x0778 },	/* ICH7 on unknown Intel */
 	{ 0x24CA, 0x1025, 0x0061 },	/* ICH4 on ACER Aspire 2023WLMi */
 	{ 0x24CA, 0x1025, 0x003d },	/* ICH4 on ACER TM290 */
 	{ 0x266F, 0x1025, 0x0066 },	/* ICH6 on ACER Aspire 1694WLMi */
-- 
GitLab


From 760cdb7760be928e85a021552253eb1b39acdf37 Mon Sep 17 00:00:00 2001
From: Steve Conklin <sconklin@canonical.com>
Date: Thu, 16 Jul 2009 16:31:10 -0500
Subject: [PATCH 0200/1153] ata_piix: Add new short cable ID

OriginalAuthor: Tony Espy <espy@canonical.com>
Signed-off-by: Steve Conklin <sconklin@canonical.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/ata_piix.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index deada1fe6a0..56b8a3ff128 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -599,6 +599,7 @@ static const struct ich_laptop ich_laptop[] = {
 	{ 0x27DF, 0x1028, 0x02b0 },	/* ICH7 on unknown Dell */
 	{ 0x27DF, 0x1043, 0x1267 },	/* ICH7 on Asus W5F */
 	{ 0x27DF, 0x103C, 0x30A1 },	/* ICH7 on HP Compaq nc2400 */
+	{ 0x27DF, 0x103C, 0x361a },	/* ICH7 on unkown HP  */
 	{ 0x27DF, 0x1071, 0xD221 },	/* ICH7 on Hercules EC-900 */
 	{ 0x27DF, 0x152D, 0x0778 },	/* ICH7 on unknown Intel */
 	{ 0x24CA, 0x1025, 0x0061 },	/* ICH4 on ACER Aspire 2023WLMi */
-- 
GitLab


From 7d084d96fdf1d791cb171da57efc1ca89d68dd6c Mon Sep 17 00:00:00 2001
From: Sergey Matyukevich <geomatsi@gmail.com>
Date: Thu, 16 Jul 2009 22:38:55 +0400
Subject: [PATCH 0201/1153] libata: Updates and fixes for pata_at91 driver

Please consider the following updates and fixes for pata_at91 driver.

* Removed extra headers
	Here we need only static memory controller properties, which are
	contained in generic header at91sam9_smc.h.
	No need to include any specific headers for at91sam9260 SoC.

* No harsh BUG_ON for get_clk in set_smc_timing function
        get_clk is now performed in driver probing function,
	        probing fails if master clock is not available

* Fixed uint/ulong mess in calc_mck_cycles function

Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/pata_at91.c | 67 ++++++++++++++++++++++-------------------
 1 file changed, 36 insertions(+), 31 deletions(-)

diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c
index 8561a9f195c..5702affcb32 100644
--- a/drivers/ata/pata_at91.c
+++ b/drivers/ata/pata_at91.c
@@ -26,9 +26,7 @@
 #include <linux/platform_device.h>
 #include <linux/ata_platform.h>
 
-#include <mach/at91sam9260_matrix.h>
 #include <mach/at91sam9_smc.h>
-#include <mach/at91sam9260.h>
 #include <mach/board.h>
 #include <mach/gpio.h>
 
@@ -44,65 +42,62 @@ struct at91_ide_info {
 	unsigned long mode;
 	unsigned int cs;
 
+	struct clk *mck;
+
 	void __iomem *ide_addr;
 	void __iomem *alt_addr;
 };
 
-const struct ata_timing initial_timing =
+static const struct ata_timing initial_timing =
 	{XFER_PIO_0, 70, 290, 240, 600, 165, 150, 600, 0};
 
-static unsigned int calc_mck_cycles(unsigned int ns, unsigned int mck_hz)
+static unsigned long calc_mck_cycles(unsigned long ns, unsigned long mck_hz)
 {
 	unsigned long mul;
 
-    /*
-     * cycles = x [nsec] * f [Hz] / 10^9 [ns in sec] =
-     *     x * (f / 1_000_000_000) =
-     *     x * ((f * 65536) / 1_000_000_000) / 65536 =
-     *     x * (((f / 10_000) * 65536) / 100_000) / 65536 =
-     */
+	/*
+	* cycles = x [nsec] * f [Hz] / 10^9 [ns in sec] =
+	*     x * (f / 1_000_000_000) =
+	*     x * ((f * 65536) / 1_000_000_000) / 65536 =
+	*     x * (((f / 10_000) * 65536) / 100_000) / 65536 =
+	*/
 
-    mul = (mck_hz / 10000) << 16;
-    mul /= 100000;
+	mul = (mck_hz / 10000) << 16;
+	mul /= 100000;
 
-    return (ns * mul + 65536) >> 16;    /* rounding */
+	return (ns * mul + 65536) >> 16;    /* rounding */
 }
 
 static void set_smc_mode(struct at91_ide_info *info)
 {
-    at91_sys_write(AT91_SMC_MODE(info->cs), info->mode);
-    return;
+	at91_sys_write(AT91_SMC_MODE(info->cs), info->mode);
+	return;
 }
 
 static void set_smc_timing(struct device *dev,
 		struct at91_ide_info *info, const struct ata_timing *ata)
 {
-	int read_cycle, write_cycle, active, recover;
-	int nrd_setup, nrd_pulse, nrd_recover;
-	int nwe_setup, nwe_pulse;
+	unsigned long read_cycle, write_cycle, active, recover;
+	unsigned long nrd_setup, nrd_pulse, nrd_recover;
+	unsigned long nwe_setup, nwe_pulse;
 
-	int ncs_write_setup, ncs_write_pulse;
-	int ncs_read_setup, ncs_read_pulse;
+	unsigned long ncs_write_setup, ncs_write_pulse;
+	unsigned long ncs_read_setup, ncs_read_pulse;
 
-	unsigned int mck_hz;
-	struct clk *mck;
+	unsigned long mck_hz;
 
 	read_cycle  = ata->cyc8b;
 	nrd_setup   = ata->setup;
 	nrd_pulse   = ata->act8b;
 	nrd_recover = ata->rec8b;
 
-	mck = clk_get(NULL, "mck");
-	BUG_ON(IS_ERR(mck));
-	mck_hz = clk_get_rate(mck);
+	mck_hz = clk_get_rate(info->mck);
 
 	read_cycle  = calc_mck_cycles(read_cycle, mck_hz);
 	nrd_setup   = calc_mck_cycles(nrd_setup, mck_hz);
 	nrd_pulse   = calc_mck_cycles(nrd_pulse, mck_hz);
 	nrd_recover = calc_mck_cycles(nrd_recover, mck_hz);
 
-	clk_put(mck);
-
 	active  = nrd_setup + nrd_pulse;
 	recover = read_cycle - active;
 
@@ -121,13 +116,13 @@ static void set_smc_timing(struct device *dev,
 	ncs_write_setup = ncs_read_setup;
 	ncs_write_pulse = ncs_read_pulse;
 
-	dev_dbg(dev, "ATA timings: nrd_setup = %d nrd_pulse = %d nrd_cycle = %d\n",
+	dev_dbg(dev, "ATA timings: nrd_setup = %lu nrd_pulse = %lu nrd_cycle = %lu\n",
 			nrd_setup, nrd_pulse, read_cycle);
-	dev_dbg(dev, "ATA timings: nwe_setup = %d nwe_pulse = %d nwe_cycle = %d\n",
+	dev_dbg(dev, "ATA timings: nwe_setup = %lu nwe_pulse = %lu nwe_cycle = %lu\n",
 			nwe_setup, nwe_pulse, write_cycle);
-	dev_dbg(dev, "ATA timings: ncs_read_setup = %d ncs_read_pulse = %d\n",
+	dev_dbg(dev, "ATA timings: ncs_read_setup = %lu ncs_read_pulse = %lu\n",
 			ncs_read_setup, ncs_read_pulse);
-	dev_dbg(dev, "ATA timings: ncs_write_setup = %d ncs_write_pulse = %d\n",
+	dev_dbg(dev, "ATA timings: ncs_write_setup = %lu ncs_write_pulse = %lu\n",
 			ncs_write_setup, ncs_write_pulse);
 
 	at91_sys_write(AT91_SMC_SETUP(info->cs),
@@ -217,6 +212,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev)
 	struct resource *mem_res;
 	struct ata_host *host;
 	struct ata_port *ap;
+
 	int irq_flags = 0;
 	int irq = 0;
 	int ret;
@@ -261,6 +257,13 @@ static int __devinit pata_at91_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
+	info->mck = clk_get(NULL, "mck");
+
+	if (IS_ERR(info->mck)) {
+		dev_err(dev, "failed to get access to mck clock\n");
+		return -ENODEV;
+	}
+
 	info->cs    = board->chipselect;
 	info->mode  = AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
 		AT91_SMC_EXNWMODE_READY | AT91_SMC_BAT_SELECT |
@@ -304,6 +307,7 @@ err_alt_ioremap:
 	devm_iounmap(dev, info->ide_addr);
 
 err_ide_ioremap:
+	clk_put(info->mck);
 	kfree(info);
 
 	return ret;
@@ -326,6 +330,7 @@ static int __devexit pata_at91_remove(struct platform_device *pdev)
 
 	devm_iounmap(dev, info->ide_addr);
 	devm_iounmap(dev, info->alt_addr);
+	clk_put(info->mck);
 
 	kfree(info);
 	return 0;
-- 
GitLab


From 5920dadfb4aec6c1372c5570e71bcd3b4837e63c Mon Sep 17 00:00:00 2001
From: Tejun Heo <tj@kernel.org>
Date: Wed, 15 Jul 2009 17:11:41 +0900
Subject: [PATCH 0202/1153] libata: accept late unlocking of HPA

On certain configurations, HPA isn't or can't be unlocked during
probing but it somehow ends up unlocked afterwards.  In the following
thread, the problem can be reliably reproduced after resuming from
STR.  The BIOS turns on HPA during boot but forgets to do it during
resume.

  http://thread.gmane.org/gmane.linux.kernel/858310

This patch updates libata revalidation such that it considers native
n_sectors.  If the device size has increased to match native
n_sectors, it's assumed that HPA has been unlocked involuntarily and
the device is recognized as the same one.  This should be fairly safe
while nicely working around the problem.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christof Warlich <christof@warlich.name>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/libata-core.c | 30 +++++++++++++++++++++++-------
 include/linux/libata.h    |  1 +
 2 files changed, 24 insertions(+), 7 deletions(-)

diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 2c6aedaef71..8ac98ff16d7 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -1515,6 +1515,7 @@ static int ata_hpa_resize(struct ata_device *dev)
 
 		return rc;
 	}
+	dev->n_native_sectors = native_sectors;
 
 	/* nothing to do? */
 	if (native_sectors <= sectors || !ata_ignore_hpa) {
@@ -4099,6 +4100,7 @@ int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class,
 		       unsigned int readid_flags)
 {
 	u64 n_sectors = dev->n_sectors;
+	u64 n_native_sectors = dev->n_native_sectors;
 	int rc;
 
 	if (!ata_dev_enabled(dev))
@@ -4128,16 +4130,30 @@ int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class,
 	/* verify n_sectors hasn't changed */
 	if (dev->class == ATA_DEV_ATA && n_sectors &&
 	    dev->n_sectors != n_sectors) {
-		ata_dev_printk(dev, KERN_INFO, "n_sectors mismatch "
+		ata_dev_printk(dev, KERN_WARNING, "n_sectors mismatch "
 			       "%llu != %llu\n",
 			       (unsigned long long)n_sectors,
 			       (unsigned long long)dev->n_sectors);
-
-		/* restore original n_sectors */
-		dev->n_sectors = n_sectors;
-
-		rc = -ENODEV;
-		goto fail;
+		/*
+		 * Something could have caused HPA to be unlocked
+		 * involuntarily.  If n_native_sectors hasn't changed
+		 * and the new size matches it, keep the device.
+		 */
+		if (dev->n_native_sectors == n_native_sectors &&
+		    dev->n_sectors > n_sectors &&
+		    dev->n_sectors == n_native_sectors) {
+			ata_dev_printk(dev, KERN_WARNING,
+				       "new n_sectors matches native, probably "
+				       "late HPA unlock, continuing\n");
+			/* keep using the old n_sectors */
+			dev->n_sectors = n_sectors;
+		} else {
+			/* restore original n_[native]_sectors and fail */
+			dev->n_native_sectors = n_native_sectors;
+			dev->n_sectors = n_sectors;
+			rc = -ENODEV;
+			goto fail;
+		}
 	}
 
 	return 0;
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 79b6d7fd4ac..e5b6e33c657 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -589,6 +589,7 @@ struct ata_device {
 #endif
 	/* n_sector is CLEAR_BEGIN, read comment above CLEAR_BEGIN */
 	u64			n_sectors;	/* size of device, if ATA */
+	u64			n_native_sectors; /* native size, if ATA */
 	unsigned int		class;		/* ATA_DEV_xxx */
 	unsigned long		unpark_deadline;
 
-- 
GitLab


From 68dbcb726e372b3c8ef60b79b5aff4174dd2bdf0 Mon Sep 17 00:00:00 2001
From: Jeff Garzik <jeff@garzik.org>
Date: Tue, 28 Jul 2009 22:36:59 -0400
Subject: [PATCH 0203/1153] Remove zero-length file drivers/char/vr41xx_giu.c

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/char/vr41xx_giu.c | 0
 1 file changed, 0 insertions(+), 0 deletions(-)
 delete mode 100644 drivers/char/vr41xx_giu.c

diff --git a/drivers/char/vr41xx_giu.c b/drivers/char/vr41xx_giu.c
deleted file mode 100644
index e69de29bb2d..00000000000
-- 
GitLab


From e024e11070a0a0dc7163ce1ec2da354a638bdbed Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Wed, 24 Jun 2009 09:48:08 +1000
Subject: [PATCH 0204/1153] drm/radeon/kms: add initial colortiling support.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

This adds new set/get tiling interfaces where the pitch
and macro/micro tiling enables can be set. Along with
a flag to decide if this object should have a surface when mapped.

The only thing we need to allocate with a mapped surface should be
the frontbuffer. Note rotate scanout shouldn't require one, and
back/depth shouldn't either, though mesa needs some fixes.

It fixes the TTM interfaces along Thomas's suggestions, and I've tested
the surface stealing code with two X servers and not seen any lockdep issues.

I've stopped tiling the fbcon frontbuffer, as I don't see there being
any advantage other than testing, I've left the testing commands in there,
just flip the fb_tiled to true in radeon_fb.c

Open: Can we integrate endian swapping in with this?

Future features:
texture tiling - need to relocate texture registers TXOFFSET* with tiling info.

This also merges Michel's cleanup surfaces regs at init time patch
even though it makes sense on its own, this patch really relies on it.

Some PowerMac firmwares set up a tiling surface at the beginning of VRAM
which messes us up otherwise.
that patch is:
Signed-off-by: Michel Dänzer <daenzer@vmware.com>

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/atombios_crtc.c      |  11 +-
 drivers/gpu/drm/radeon/r100.c               |  79 +++++++++++-
 drivers/gpu/drm/radeon/r300.c               |  51 +++++++-
 drivers/gpu/drm/radeon/r300_reg.h           |   4 +-
 drivers/gpu/drm/radeon/radeon.h             |  32 ++++-
 drivers/gpu/drm/radeon/radeon_asic.h        |  19 +++
 drivers/gpu/drm/radeon/radeon_device.c      |   2 +
 drivers/gpu/drm/radeon/radeon_fb.c          |  12 +-
 drivers/gpu/drm/radeon/radeon_gem.c         |  41 ++++++
 drivers/gpu/drm/radeon/radeon_kms.c         |   2 +
 drivers/gpu/drm/radeon/radeon_legacy_crtc.c |  15 ++-
 drivers/gpu/drm/radeon/radeon_object.c      | 130 ++++++++++++++++++++
 drivers/gpu/drm/radeon/radeon_ttm.c         |   2 +
 drivers/gpu/drm/ttm/ttm_bo.c                |   5 +-
 drivers/gpu/drm/ttm/ttm_bo_vm.c             |   3 +
 include/drm/radeon_drm.h                    |  23 +++-
 include/drm/ttm/ttm_bo_driver.h             |  15 +++
 17 files changed, 427 insertions(+), 19 deletions(-)

diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c
index e64a199b5ee..eac26cdb5da 100644
--- a/drivers/gpu/drm/radeon/atombios_crtc.c
+++ b/drivers/gpu/drm/radeon/atombios_crtc.c
@@ -327,7 +327,7 @@ int atombios_crtc_set_base(struct drm_crtc *crtc, int x, int y,
 	struct drm_gem_object *obj;
 	struct drm_radeon_gem_object *obj_priv;
 	uint64_t fb_location;
-	uint32_t fb_format, fb_pitch_pixels;
+	uint32_t fb_format, fb_pitch_pixels, tiling_flags;
 
 	if (!crtc->fb)
 		return -EINVAL;
@@ -364,7 +364,14 @@ int atombios_crtc_set_base(struct drm_crtc *crtc, int x, int y,
 		return -EINVAL;
 	}
 
-	/* TODO tiling */
+	radeon_object_get_tiling_flags(obj->driver_private,
+				       &tiling_flags, NULL);
+	if (tiling_flags & RADEON_TILING_MACRO)
+		fb_format |= AVIVO_D1GRPH_MACRO_ADDRESS_MODE;
+
+	if (tiling_flags & RADEON_TILING_MICRO)
+		fb_format |= AVIVO_D1GRPH_TILED;
+
 	if (radeon_crtc->crtc_id == 0)
 		WREG32(AVIVO_D1VGA_CONTROL, 0);
 	else
diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index 0d05909f03f..69bd7cb5997 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -909,6 +909,7 @@ static int r100_packet0_check(struct radeon_cs_parser *p,
 	unsigned idx;
 	bool onereg;
 	int r;
+	u32 tile_flags = 0;
 
 	ib = p->ib->ptr;
 	ib_chunk = &p->chunks[p->chunk_ib_idx];
@@ -942,7 +943,20 @@ static int r100_packet0_check(struct radeon_cs_parser *p,
 			}
 			tmp = ib_chunk->kdata[idx] & 0x003fffff;
 			tmp += (((u32)reloc->lobj.gpu_offset) >> 10);
-			ib[idx] = (ib_chunk->kdata[idx] & 0xffc00000) | tmp;
+
+			if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO)
+				tile_flags |= RADEON_DST_TILE_MACRO;
+			if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) {
+				if (reg == RADEON_SRC_PITCH_OFFSET) {
+					DRM_ERROR("Cannot src blit from microtiled surface\n");
+					r100_cs_dump_packet(p, pkt);
+					return -EINVAL;
+				}
+				tile_flags |= RADEON_DST_TILE_MICRO;
+			}
+
+			tmp |= tile_flags;
+			ib[idx] = (ib_chunk->kdata[idx] & 0x3fc00000) | tmp;
 			break;
 		case RADEON_RB3D_DEPTHOFFSET:
 		case RADEON_RB3D_COLOROFFSET:
@@ -987,6 +1001,25 @@ static int r100_packet0_check(struct radeon_cs_parser *p,
 			}
 			ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
 			break;
+		case R300_RB3D_COLORPITCH0:
+		case RADEON_RB3D_COLORPITCH:
+			r = r100_cs_packet_next_reloc(p, &reloc);
+			if (r) {
+				DRM_ERROR("No reloc for ib[%d]=0x%04X\n",
+					  idx, reg);
+				r100_cs_dump_packet(p, pkt);
+				return r;
+			}
+
+			if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO)
+				tile_flags |= RADEON_COLOR_TILE_ENABLE;
+			if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO)
+				tile_flags |= RADEON_COLOR_MICROTILE_ENABLE;
+
+			tmp = ib_chunk->kdata[idx] & ~(0x7 << 16);
+			tmp |= tile_flags;
+			ib[idx] = tmp;
+			break;
 		default:
 			/* FIXME: we don't want to allow anyothers packet */
 			break;
@@ -1707,3 +1740,47 @@ int r100_debugfs_mc_info_init(struct radeon_device *rdev)
 	return 0;
 #endif
 }
+
+int r100_set_surface_reg(struct radeon_device *rdev, int reg,
+			 uint32_t tiling_flags, uint32_t pitch,
+			 uint32_t offset, uint32_t obj_size)
+{
+	int surf_index = reg * 16;
+	int flags = 0;
+
+	/* r100/r200 divide by 16 */
+	if (rdev->family < CHIP_R300)
+		flags = pitch / 16;
+	else
+		flags = pitch / 8;
+
+	if (rdev->family <= CHIP_RS200) {
+		if ((tiling_flags & (RADEON_TILING_MACRO|RADEON_TILING_MICRO))
+				 == (RADEON_TILING_MACRO|RADEON_TILING_MICRO))
+			flags |= RADEON_SURF_TILE_COLOR_BOTH;
+		if (tiling_flags & RADEON_TILING_MACRO)
+			flags |= RADEON_SURF_TILE_COLOR_MACRO;
+	} else if (rdev->family <= CHIP_RV280) {
+		if (tiling_flags & (RADEON_TILING_MACRO))
+			flags |= R200_SURF_TILE_COLOR_MACRO;
+		if (tiling_flags & RADEON_TILING_MICRO)
+			flags |= R200_SURF_TILE_COLOR_MICRO;
+	} else {
+		if (tiling_flags & RADEON_TILING_MACRO)
+			flags |= R300_SURF_TILE_MACRO;
+		if (tiling_flags & RADEON_TILING_MICRO)
+			flags |= R300_SURF_TILE_MICRO;
+	}
+
+	DRM_DEBUG("writing surface %d %d %x %x\n", reg, flags, offset, offset+obj_size-1);
+	WREG32(RADEON_SURFACE0_INFO + surf_index, flags);
+	WREG32(RADEON_SURFACE0_LOWER_BOUND + surf_index, offset);
+	WREG32(RADEON_SURFACE0_UPPER_BOUND + surf_index, offset + obj_size - 1);
+	return 0;
+}
+
+void r100_clear_surface_reg(struct radeon_device *rdev, int reg)
+{
+	int surf_index = reg * 16;
+	WREG32(RADEON_SURFACE0_INFO + surf_index, 0);
+}
diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c
index 0e0e094da50..28e5777658b 100644
--- a/drivers/gpu/drm/radeon/r300.c
+++ b/drivers/gpu/drm/radeon/r300.c
@@ -30,6 +30,7 @@
 #include "drm.h"
 #include "radeon_reg.h"
 #include "radeon.h"
+#include "radeon_drm.h"
 
 /* r300,r350,rv350,rv370,rv380 depends on : */
 void r100_hdp_reset(struct radeon_device *rdev);
@@ -1023,7 +1024,7 @@ static int r300_packet0_check(struct radeon_cs_parser *p,
 	struct radeon_cs_reloc *reloc;
 	struct r300_cs_track *track;
 	volatile uint32_t *ib;
-	uint32_t tmp;
+	uint32_t tmp, tile_flags = 0;
 	unsigned i;
 	int r;
 
@@ -1052,7 +1053,19 @@ static int r300_packet0_check(struct radeon_cs_parser *p,
 		}
 		tmp = ib_chunk->kdata[idx] & 0x003fffff;
 		tmp += (((u32)reloc->lobj.gpu_offset) >> 10);
-		ib[idx] = (ib_chunk->kdata[idx] & 0xffc00000) | tmp;
+
+		if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO)
+			tile_flags |= RADEON_DST_TILE_MACRO;
+		if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO) {
+			if (reg == RADEON_SRC_PITCH_OFFSET) {
+				DRM_ERROR("Cannot src blit from microtiled surface\n");
+				r100_cs_dump_packet(p, pkt);
+				return -EINVAL;
+			}
+			tile_flags |= RADEON_DST_TILE_MICRO;
+		}
+		tmp |= tile_flags;
+		ib[idx] = (ib_chunk->kdata[idx] & 0x3fc00000) | tmp;
 		break;
 	case R300_RB3D_COLOROFFSET0:
 	case R300_RB3D_COLOROFFSET1:
@@ -1141,6 +1154,23 @@ static int r300_packet0_check(struct radeon_cs_parser *p,
 		/* RB3D_COLORPITCH1 */
 		/* RB3D_COLORPITCH2 */
 		/* RB3D_COLORPITCH3 */
+		r = r100_cs_packet_next_reloc(p, &reloc);
+		if (r) {
+			DRM_ERROR("No reloc for ib[%d]=0x%04X\n",
+				  idx, reg);
+			r100_cs_dump_packet(p, pkt);
+			return r;
+		}
+
+		if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO)
+			tile_flags |= R300_COLOR_TILE_ENABLE;
+		if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO)
+			tile_flags |= R300_COLOR_MICROTILE_ENABLE;
+
+		tmp = ib_chunk->kdata[idx] & ~(0x7 << 16);
+		tmp |= tile_flags;
+		ib[idx] = tmp;
+
 		i = (reg - 0x4E38) >> 2;
 		track->cb[i].pitch = ib_chunk->kdata[idx] & 0x3FFE;
 		switch (((ib_chunk->kdata[idx] >> 21) & 0xF)) {
@@ -1196,6 +1226,23 @@ static int r300_packet0_check(struct radeon_cs_parser *p,
 		break;
 	case 0x4F24:
 		/* ZB_DEPTHPITCH */
+		r = r100_cs_packet_next_reloc(p, &reloc);
+		if (r) {
+			DRM_ERROR("No reloc for ib[%d]=0x%04X\n",
+				  idx, reg);
+			r100_cs_dump_packet(p, pkt);
+			return r;
+		}
+
+		if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO)
+			tile_flags |= R300_DEPTHMACROTILE_ENABLE;
+		if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO)
+			tile_flags |= R300_DEPTHMICROTILE_TILED;;
+
+		tmp = ib_chunk->kdata[idx] & ~(0x7 << 16);
+		tmp |= tile_flags;
+		ib[idx] = tmp;
+
 		track->zb.pitch = ib_chunk->kdata[idx] & 0x3FFC;
 		break;
 	case 0x4104:
diff --git a/drivers/gpu/drm/radeon/r300_reg.h b/drivers/gpu/drm/radeon/r300_reg.h
index 70f48609515..4b7afef35a6 100644
--- a/drivers/gpu/drm/radeon/r300_reg.h
+++ b/drivers/gpu/drm/radeon/r300_reg.h
@@ -27,7 +27,9 @@
 #ifndef _R300_REG_H_
 #define _R300_REG_H_
 
-
+#define R300_SURF_TILE_MACRO (1<<16)
+#define R300_SURF_TILE_MICRO (2<<16)
+#define R300_SURF_TILE_BOTH (3<<16)
 
 
 #define R300_MC_INIT_MISC_LAT_TIMER	0x180
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index 7f007185e7f..af12a2fe322 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -201,6 +201,14 @@ int radeon_fence_wait_last(struct radeon_device *rdev);
 struct radeon_fence *radeon_fence_ref(struct radeon_fence *fence);
 void radeon_fence_unref(struct radeon_fence **fence);
 
+/*
+ * Tiling registers
+ */
+struct radeon_surface_reg {
+	struct radeon_object *robj;
+};
+
+#define RADEON_GEM_MAX_SURFACES 8
 
 /*
  * Radeon buffer.
@@ -213,6 +221,7 @@ struct radeon_object_list {
 	uint64_t		gpu_offset;
 	unsigned		rdomain;
 	unsigned		wdomain;
+	uint32_t                tiling_flags;
 };
 
 int radeon_object_init(struct radeon_device *rdev);
@@ -242,8 +251,15 @@ void radeon_object_list_clean(struct list_head *head);
 int radeon_object_fbdev_mmap(struct radeon_object *robj,
 			     struct vm_area_struct *vma);
 unsigned long radeon_object_size(struct radeon_object *robj);
-
-
+void radeon_object_clear_surface_reg(struct radeon_object *robj);
+int radeon_object_check_tiling(struct radeon_object *robj, bool has_moved,
+			       bool force_drop);
+void radeon_object_set_tiling_flags(struct radeon_object *robj,
+				    uint32_t tiling_flags, uint32_t pitch);
+void radeon_object_get_tiling_flags(struct radeon_object *robj, uint32_t *tiling_flags, uint32_t *pitch);
+void radeon_bo_move_notify(struct ttm_buffer_object *bo,
+			   struct ttm_mem_reg *mem);
+void radeon_bo_fault_reserve_notify(struct ttm_buffer_object *bo);
 /*
  * GEM objects.
  */
@@ -535,6 +551,11 @@ struct radeon_asic {
 	void (*set_memory_clock)(struct radeon_device *rdev, uint32_t mem_clock);
 	void (*set_pcie_lanes)(struct radeon_device *rdev, int lanes);
 	void (*set_clock_gating)(struct radeon_device *rdev, int enable);
+
+	int (*set_surface_reg)(struct radeon_device *rdev, int reg,
+			       uint32_t tiling_flags, uint32_t pitch,
+			       uint32_t offset, uint32_t obj_size);
+	int (*clear_surface_reg)(struct radeon_device *rdev, int reg);
 };
 
 union radeon_asic_config {
@@ -568,6 +589,10 @@ int radeon_gem_busy_ioctl(struct drm_device *dev, void *data,
 int radeon_gem_wait_idle_ioctl(struct drm_device *dev, void *data,
 			      struct drm_file *filp);
 int radeon_cs_ioctl(struct drm_device *dev, void *data, struct drm_file *filp);
+int radeon_gem_set_tiling_ioctl(struct drm_device *dev, void *data,
+				struct drm_file *filp);
+int radeon_gem_get_tiling_ioctl(struct drm_device *dev, void *data,
+				struct drm_file *filp);
 
 
 /*
@@ -627,6 +652,7 @@ struct radeon_device {
 	bool				shutdown;
 	bool				suspend;
 	bool				need_dma32;
+	struct radeon_surface_reg surface_regs[RADEON_GEM_MAX_SURFACES];
 };
 
 int radeon_device_init(struct radeon_device *rdev,
@@ -801,5 +827,7 @@ static inline void radeon_ring_write(struct radeon_device *rdev, uint32_t v)
 #define radeon_set_memory_clock(rdev, e) (rdev)->asic->set_engine_clock((rdev), (e))
 #define radeon_set_pcie_lanes(rdev, l) (rdev)->asic->set_pcie_lanes((rdev), (l))
 #define radeon_set_clock_gating(rdev, e) (rdev)->asic->set_clock_gating((rdev), (e))
+#define radeon_set_surface_reg(rdev, r, f, p, o, s) ((rdev)->asic->set_surface_reg((rdev), (r), (f), (p), (o), (s)))
+#define radeon_clear_surface_reg(rdev, r) ((rdev)->asic->clear_surface_reg((rdev), (r)))
 
 #endif
diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h
index e2e567395df..dd903d32940 100644
--- a/drivers/gpu/drm/radeon/radeon_asic.h
+++ b/drivers/gpu/drm/radeon/radeon_asic.h
@@ -71,6 +71,10 @@ int r100_copy_blit(struct radeon_device *rdev,
 		   uint64_t dst_offset,
 		   unsigned num_pages,
 		   struct radeon_fence *fence);
+int r100_set_surface_reg(struct radeon_device *rdev, int reg,
+			 uint32_t tiling_flags, uint32_t pitch,
+			 uint32_t offset, uint32_t obj_size);
+int r100_clear_surface_reg(struct radeon_device *rdev, int reg);
 
 static struct radeon_asic r100_asic = {
 	.init = &r100_init,
@@ -100,6 +104,8 @@ static struct radeon_asic r100_asic = {
 	.set_memory_clock = NULL,
 	.set_pcie_lanes = NULL,
 	.set_clock_gating = &radeon_legacy_set_clock_gating,
+	.set_surface_reg = r100_set_surface_reg,
+	.clear_surface_reg = r100_clear_surface_reg,
 };
 
 
@@ -128,6 +134,7 @@ int r300_copy_dma(struct radeon_device *rdev,
 		  uint64_t dst_offset,
 		  unsigned num_pages,
 		  struct radeon_fence *fence);
+
 static struct radeon_asic r300_asic = {
 	.init = &r300_init,
 	.errata = &r300_errata,
@@ -156,6 +163,8 @@ static struct radeon_asic r300_asic = {
 	.set_memory_clock = NULL,
 	.set_pcie_lanes = &rv370_set_pcie_lanes,
 	.set_clock_gating = &radeon_legacy_set_clock_gating,
+	.set_surface_reg = r100_set_surface_reg,
+	.clear_surface_reg = r100_clear_surface_reg,
 };
 
 /*
@@ -193,6 +202,8 @@ static struct radeon_asic r420_asic = {
 	.set_memory_clock = &radeon_atom_set_memory_clock,
 	.set_pcie_lanes = &rv370_set_pcie_lanes,
 	.set_clock_gating = &radeon_atom_set_clock_gating,
+	.set_surface_reg = r100_set_surface_reg,
+	.clear_surface_reg = r100_clear_surface_reg,
 };
 
 
@@ -237,6 +248,8 @@ static struct radeon_asic rs400_asic = {
 	.set_memory_clock = NULL,
 	.set_pcie_lanes = NULL,
 	.set_clock_gating = &radeon_legacy_set_clock_gating,
+	.set_surface_reg = r100_set_surface_reg,
+	.clear_surface_reg = r100_clear_surface_reg,
 };
 
 
@@ -322,6 +335,8 @@ static struct radeon_asic rs690_asic = {
 	.set_memory_clock = &radeon_atom_set_memory_clock,
 	.set_pcie_lanes = NULL,
 	.set_clock_gating = &radeon_atom_set_clock_gating,
+	.set_surface_reg = r100_set_surface_reg,
+	.clear_surface_reg = r100_clear_surface_reg,
 };
 
 
@@ -367,6 +382,8 @@ static struct radeon_asic rv515_asic = {
 	.set_memory_clock = &radeon_atom_set_memory_clock,
 	.set_pcie_lanes = &rv370_set_pcie_lanes,
 	.set_clock_gating = &radeon_atom_set_clock_gating,
+	.set_surface_reg = r100_set_surface_reg,
+	.clear_surface_reg = r100_clear_surface_reg,
 };
 
 
@@ -405,6 +422,8 @@ static struct radeon_asic r520_asic = {
 	.set_memory_clock = &radeon_atom_set_memory_clock,
 	.set_pcie_lanes = &rv370_set_pcie_lanes,
 	.set_clock_gating = &radeon_atom_set_clock_gating,
+	.set_surface_reg = r100_set_surface_reg,
+	.clear_surface_reg = r100_clear_surface_reg,
 };
 
 /*
diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c
index cdef6eb01ba..f23083bbba3 100644
--- a/drivers/gpu/drm/radeon/radeon_device.c
+++ b/drivers/gpu/drm/radeon/radeon_device.c
@@ -48,6 +48,8 @@ static void radeon_surface_init(struct radeon_device *rdev)
 			       i * (RADEON_SURFACE1_INFO - RADEON_SURFACE0_INFO),
 			       0);
 		}
+		/* enable surfaces */
+		WREG32(RADEON_SURFACE_CNTL, 0);
 	}
 }
 
diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c
index 260870a29d8..36d2f5588f2 100644
--- a/drivers/gpu/drm/radeon/radeon_fb.c
+++ b/drivers/gpu/drm/radeon/radeon_fb.c
@@ -471,10 +471,10 @@ static struct notifier_block paniced = {
 	.notifier_call = radeonfb_panic,
 };
 
-static int radeon_align_pitch(struct radeon_device *rdev, int width, int bpp)
+static int radeon_align_pitch(struct radeon_device *rdev, int width, int bpp, bool tiled)
 {
 	int aligned = width;
-	int align_large = (ASIC_IS_AVIVO(rdev));
+	int align_large = (ASIC_IS_AVIVO(rdev)) || tiled;
 	int pitch_mask = 0;
 
 	switch (bpp / 8) {
@@ -512,12 +512,13 @@ int radeonfb_create(struct radeon_device *rdev,
 	u64 fb_gpuaddr;
 	void *fbptr = NULL;
 	unsigned long tmp;
+	bool fb_tiled = false; /* useful for testing */
 
 	mode_cmd.width = surface_width;
 	mode_cmd.height = surface_height;
 	mode_cmd.bpp = 32;
 	/* need to align pitch with crtc limits */
-	mode_cmd.pitch = radeon_align_pitch(rdev, mode_cmd.width, mode_cmd.bpp) * ((mode_cmd.bpp + 1) / 8);
+	mode_cmd.pitch = radeon_align_pitch(rdev, mode_cmd.width, mode_cmd.bpp, fb_tiled) * ((mode_cmd.bpp + 1) / 8);
 	mode_cmd.depth = 24;
 
 	size = mode_cmd.pitch * mode_cmd.height;
@@ -535,6 +536,8 @@ int radeonfb_create(struct radeon_device *rdev,
 	}
 	robj = gobj->driver_private;
 
+	if (fb_tiled)
+		radeon_object_set_tiling_flags(robj, RADEON_TILING_MACRO|RADEON_TILING_SURFACE, mode_cmd.pitch);
 	mutex_lock(&rdev->ddev->struct_mutex);
 	fb = radeon_framebuffer_create(rdev->ddev, &mode_cmd, gobj);
 	if (fb == NULL) {
@@ -563,6 +566,9 @@ int radeonfb_create(struct radeon_device *rdev,
 	}
 	rfbdev = info->par;
 
+	if (fb_tiled)
+		radeon_object_check_tiling(robj, 0, 0);
+
 	ret = radeon_object_kmap(robj, &fbptr);
 	if (ret) {
 		goto out_unref;
diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c
index eb516034235..12542087b29 100644
--- a/drivers/gpu/drm/radeon/radeon_gem.c
+++ b/drivers/gpu/drm/radeon/radeon_gem.c
@@ -285,3 +285,44 @@ int radeon_gem_wait_idle_ioctl(struct drm_device *dev, void *data,
 	mutex_unlock(&dev->struct_mutex);
 	return r;
 }
+
+int radeon_gem_set_tiling_ioctl(struct drm_device *dev, void *data,
+				struct drm_file *filp)
+{
+	struct drm_radeon_gem_set_tiling *args = data;
+	struct drm_gem_object *gobj;
+	struct radeon_object *robj;
+	int r = 0;
+
+	DRM_DEBUG("%d \n", args->handle);
+	gobj = drm_gem_object_lookup(dev, filp, args->handle);
+	if (gobj == NULL)
+		return -EINVAL;
+	robj = gobj->driver_private;
+	radeon_object_set_tiling_flags(robj, args->tiling_flags, args->pitch);
+	mutex_lock(&dev->struct_mutex);
+	drm_gem_object_unreference(gobj);
+	mutex_unlock(&dev->struct_mutex);
+	return r;
+}
+
+int radeon_gem_get_tiling_ioctl(struct drm_device *dev, void *data,
+				struct drm_file *filp)
+{
+	struct drm_radeon_gem_get_tiling *args = data;
+	struct drm_gem_object *gobj;
+	struct radeon_object *robj;
+	int r = 0;
+
+	DRM_DEBUG("\n");
+	gobj = drm_gem_object_lookup(dev, filp, args->handle);
+	if (gobj == NULL)
+		return -EINVAL;
+	robj = gobj->driver_private;
+	radeon_object_get_tiling_flags(robj, &args->tiling_flags,
+				       &args->pitch);
+	mutex_lock(&dev->struct_mutex);
+	drm_gem_object_unreference(gobj);
+	mutex_unlock(&dev->struct_mutex);
+	return r;
+}
diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c
index 4612a7c146d..937a2f1cdb4 100644
--- a/drivers/gpu/drm/radeon/radeon_kms.c
+++ b/drivers/gpu/drm/radeon/radeon_kms.c
@@ -291,5 +291,7 @@ struct drm_ioctl_desc radeon_ioctls_kms[] = {
 	DRM_IOCTL_DEF(DRM_RADEON_GEM_WAIT_IDLE, radeon_gem_wait_idle_ioctl, DRM_AUTH),
 	DRM_IOCTL_DEF(DRM_RADEON_CS, radeon_cs_ioctl, DRM_AUTH),
 	DRM_IOCTL_DEF(DRM_RADEON_INFO, radeon_info_ioctl, DRM_AUTH),
+	DRM_IOCTL_DEF(DRM_RADEON_GEM_SET_TILING, radeon_gem_set_tiling_ioctl, DRM_AUTH),
+	DRM_IOCTL_DEF(DRM_RADEON_GEM_GET_TILING, radeon_gem_get_tiling_ioctl, DRM_AUTH),
 };
 int radeon_max_kms_ioctl = DRM_ARRAY_SIZE(radeon_ioctls_kms);
diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
index 14c1a5107fc..0613790e2a5 100644
--- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
+++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
@@ -235,6 +235,7 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y,
 	uint64_t base;
 	uint32_t crtc_offset, crtc_offset_cntl, crtc_tile_x0_y0 = 0;
 	uint32_t crtc_pitch, pitch_pixels;
+	uint32_t tiling_flags;
 
 	DRM_DEBUG("\n");
 
@@ -258,8 +259,12 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y,
 		       (crtc->fb->bits_per_pixel * 8));
 	crtc_pitch |= crtc_pitch << 16;
 
-	/* TODO tiling */
-	if (0) {
+	radeon_object_get_tiling_flags(obj->driver_private,
+				       &tiling_flags, NULL);
+	if (tiling_flags & RADEON_TILING_MICRO)
+		DRM_ERROR("trying to scanout microtiled buffer\n");
+
+	if (tiling_flags & RADEON_TILING_MACRO) {
 		if (ASIC_IS_R300(rdev))
 			crtc_offset_cntl |= (R300_CRTC_X_Y_MODE_EN |
 					     R300_CRTC_MICRO_TILE_BUFFER_DIS |
@@ -275,15 +280,13 @@ int radeon_crtc_set_base(struct drm_crtc *crtc, int x, int y,
 			crtc_offset_cntl &= ~RADEON_CRTC_TILE_EN;
 	}
 
-
-	/* TODO more tiling */
-	if (0) {
+	if (tiling_flags & RADEON_TILING_MACRO) {
 		if (ASIC_IS_R300(rdev)) {
 			crtc_tile_x0_y0 = x | (y << 16);
 			base &= ~0x7ff;
 		} else {
 			int byteshift = crtc->fb->bits_per_pixel >> 4;
-			int tile_addr = (((y >> 3) * crtc->fb->width + x) >> (8 - byteshift)) << 11;
+			int tile_addr = (((y >> 3) * pitch_pixels +  x) >> (8 - byteshift)) << 11;
 			base += tile_addr + ((x << byteshift) % 256) + ((y % 8) << 8);
 			crtc_offset_cntl |= (y % 16);
 		}
diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c
index bac0d06c52a..d5b1fd562d8 100644
--- a/drivers/gpu/drm/radeon/radeon_object.c
+++ b/drivers/gpu/drm/radeon/radeon_object.c
@@ -44,6 +44,9 @@ struct radeon_object {
 	uint64_t			gpu_addr;
 	void				*kptr;
 	bool				is_iomem;
+	uint32_t			tiling_flags;
+	uint32_t			pitch;
+	int				surface_reg;
 };
 
 int radeon_ttm_init(struct radeon_device *rdev);
@@ -70,6 +73,7 @@ static void radeon_ttm_object_object_destroy(struct ttm_buffer_object *tobj)
 
 	robj = container_of(tobj, struct radeon_object, tobj);
 	list_del_init(&robj->list);
+	radeon_object_clear_surface_reg(robj);
 	kfree(robj);
 }
 
@@ -141,6 +145,7 @@ int radeon_object_create(struct radeon_device *rdev,
 	}
 	robj->rdev = rdev;
 	robj->gobj = gobj;
+	robj->surface_reg = -1;
 	INIT_LIST_HEAD(&robj->list);
 
 	flags = radeon_object_flags_from_domain(domain);
@@ -435,6 +440,7 @@ int radeon_object_list_validate(struct list_head *head, void *fence)
 			radeon_object_gpu_addr(robj);
 		}
 		lobj->gpu_offset = robj->gpu_addr;
+		lobj->tiling_flags = robj->tiling_flags;
 		if (fence) {
 			old_fence = (struct radeon_fence *)robj->tobj.sync_obj;
 			robj->tobj.sync_obj = radeon_fence_ref(fence);
@@ -479,3 +485,127 @@ unsigned long radeon_object_size(struct radeon_object *robj)
 {
 	return robj->tobj.num_pages << PAGE_SHIFT;
 }
+
+int radeon_object_get_surface_reg(struct radeon_object *robj)
+{
+	struct radeon_device *rdev = robj->rdev;
+	struct radeon_surface_reg *reg;
+	struct radeon_object *old_object;
+	int steal;
+	int i;
+
+	if (!robj->tiling_flags)
+		return 0;
+
+	if (robj->surface_reg >= 0) {
+		reg = &rdev->surface_regs[robj->surface_reg];
+		i = robj->surface_reg;
+		goto out;
+	}
+
+	steal = -1;
+	for (i = 0; i < RADEON_GEM_MAX_SURFACES; i++) {
+
+		reg = &rdev->surface_regs[i];
+		if (!reg->robj)
+			break;
+
+		old_object = reg->robj;
+		if (old_object->pin_count == 0)
+			steal = i;
+	}
+
+	/* if we are all out */
+	if (i == RADEON_GEM_MAX_SURFACES) {
+		if (steal == -1)
+			return -ENOMEM;
+		/* find someone with a surface reg and nuke their BO */
+		reg = &rdev->surface_regs[steal];
+		old_object = reg->robj;
+		/* blow away the mapping */
+		DRM_DEBUG("stealing surface reg %d from %p\n", steal, old_object);
+		ttm_bo_unmap_virtual(&old_object->tobj);
+		old_object->surface_reg = -1;
+		i = steal;
+	}
+
+	robj->surface_reg = i;
+	reg->robj = robj;
+
+out:
+	radeon_set_surface_reg(rdev, i, robj->tiling_flags, robj->pitch,
+			       robj->tobj.mem.mm_node->start << PAGE_SHIFT,
+			       robj->tobj.num_pages << PAGE_SHIFT);
+	return 0;
+}
+
+void radeon_object_clear_surface_reg(struct radeon_object *robj)
+{
+	struct radeon_device *rdev = robj->rdev;
+	struct radeon_surface_reg *reg;
+
+	if (robj->surface_reg == -1)
+		return;
+
+	reg = &rdev->surface_regs[robj->surface_reg];
+	radeon_clear_surface_reg(rdev, robj->surface_reg);
+
+	reg->robj = NULL;
+	robj->surface_reg = -1;
+}
+
+void radeon_object_set_tiling_flags(struct radeon_object *robj,
+				    uint32_t tiling_flags, uint32_t pitch)
+{
+	robj->tiling_flags = tiling_flags;
+	robj->pitch = pitch;
+}
+
+void radeon_object_get_tiling_flags(struct radeon_object *robj,
+				    uint32_t *tiling_flags,
+				    uint32_t *pitch)
+{
+	if (tiling_flags)
+		*tiling_flags = robj->tiling_flags;
+	if (pitch)
+		*pitch = robj->pitch;
+}
+
+int radeon_object_check_tiling(struct radeon_object *robj, bool has_moved,
+			       bool force_drop)
+{
+	if (!(robj->tiling_flags & RADEON_TILING_SURFACE))
+		return 0;
+
+	if (force_drop) {
+		radeon_object_clear_surface_reg(robj);
+		return 0;
+	}
+
+	if (robj->tobj.mem.mem_type != TTM_PL_VRAM) {
+		if (!has_moved)
+			return 0;
+
+		if (robj->surface_reg >= 0)
+			radeon_object_clear_surface_reg(robj);
+		return 0;
+	}
+
+	if ((robj->surface_reg >= 0) && !has_moved)
+		return 0;
+
+	return radeon_object_get_surface_reg(robj);
+}
+
+void radeon_bo_move_notify(struct ttm_buffer_object *bo,
+			  struct ttm_mem_reg *mem)
+{
+	struct radeon_object *robj = container_of(bo, struct radeon_object, tobj);
+	radeon_object_check_tiling(robj, 0, 1);
+}
+
+void radeon_bo_fault_reserve_notify(struct ttm_buffer_object *bo)
+{
+	struct radeon_object *robj = container_of(bo, struct radeon_object, tobj);
+	radeon_object_check_tiling(robj, 0, 0);
+}
diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c
index 4ca9aa9203d..37e1cbcce3a 100644
--- a/drivers/gpu/drm/radeon/radeon_ttm.c
+++ b/drivers/gpu/drm/radeon/radeon_ttm.c
@@ -429,6 +429,8 @@ static struct ttm_bo_driver radeon_bo_driver = {
 	.sync_obj_flush = &radeon_sync_obj_flush,
 	.sync_obj_unref = &radeon_sync_obj_unref,
 	.sync_obj_ref = &radeon_sync_obj_ref,
+	.move_notify = &radeon_bo_move_notify,
+	.fault_reserve_notify = &radeon_bo_fault_reserve_notify,
 };
 
 int radeon_ttm_init(struct radeon_device *rdev)
diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c
index e55e7972c89..6538d423698 100644
--- a/drivers/gpu/drm/ttm/ttm_bo.c
+++ b/drivers/gpu/drm/ttm/ttm_bo.c
@@ -43,7 +43,6 @@
 #define TTM_BO_HASH_ORDER 13
 
 static int ttm_bo_setup_vm(struct ttm_buffer_object *bo);
-static void ttm_bo_unmap_virtual(struct ttm_buffer_object *bo);
 static int ttm_bo_swapout(struct ttm_mem_shrink *shrink);
 
 static inline uint32_t ttm_bo_type_flags(unsigned type)
@@ -307,6 +306,9 @@ static int ttm_bo_handle_move_mem(struct ttm_buffer_object *bo,
 
 	}
 
+	if (bdev->driver->move_notify)
+		bdev->driver->move_notify(bo, mem);
+
 	if (!(old_man->flags & TTM_MEMTYPE_FLAG_FIXED) &&
 	    !(new_man->flags & TTM_MEMTYPE_FLAG_FIXED))
 		ret = ttm_bo_move_ttm(bo, evict, no_wait, mem);
@@ -1451,6 +1453,7 @@ void ttm_bo_unmap_virtual(struct ttm_buffer_object *bo)
 
 	unmap_mapping_range(bdev->dev_mapping, offset, holelen, 1);
 }
+EXPORT_SYMBOL(ttm_bo_unmap_virtual);
 
 static void ttm_bo_vm_insert_rb(struct ttm_buffer_object *bo)
 {
diff --git a/drivers/gpu/drm/ttm/ttm_bo_vm.c b/drivers/gpu/drm/ttm/ttm_bo_vm.c
index 40b75032ea4..41c907f6c56 100644
--- a/drivers/gpu/drm/ttm/ttm_bo_vm.c
+++ b/drivers/gpu/drm/ttm/ttm_bo_vm.c
@@ -101,6 +101,9 @@ static int ttm_bo_vm_fault(struct vm_area_struct *vma, struct vm_fault *vmf)
 		return VM_FAULT_NOPAGE;
 	}
 
+	if (bdev->driver->fault_reserve_notify)
+		bdev->driver->fault_reserve_notify(bo);
+
 	/*
 	 * Wait for buffer data in transit, due to a pipelined
 	 * move.
diff --git a/include/drm/radeon_drm.h b/include/drm/radeon_drm.h
index 41862e9a4c2..af4b4826997 100644
--- a/include/drm/radeon_drm.h
+++ b/include/drm/radeon_drm.h
@@ -506,6 +506,8 @@ typedef struct {
 #define DRM_RADEON_GEM_WAIT_IDLE	0x24
 #define DRM_RADEON_CS			0x26
 #define DRM_RADEON_INFO			0x27
+#define DRM_RADEON_GEM_SET_TILING	0x28
+#define DRM_RADEON_GEM_GET_TILING	0x29
 
 #define DRM_IOCTL_RADEON_CP_INIT    DRM_IOW( DRM_COMMAND_BASE + DRM_RADEON_CP_INIT, drm_radeon_init_t)
 #define DRM_IOCTL_RADEON_CP_START   DRM_IO(  DRM_COMMAND_BASE + DRM_RADEON_CP_START)
@@ -544,7 +546,8 @@ typedef struct {
 #define DRM_IOCTL_RADEON_GEM_WAIT_IDLE	DRM_IOW(DRM_COMMAND_BASE + DRM_RADEON_GEM_WAIT_IDLE, struct drm_radeon_gem_wait_idle)
 #define DRM_IOCTL_RADEON_CS		DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_CS, struct drm_radeon_cs)
 #define DRM_IOCTL_RADEON_INFO		DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_INFO, struct drm_radeon_info)
-
+#define DRM_IOCTL_RADEON_SET_TILING	DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_SET_TILING, struct drm_radeon_gem_set_tiling)
+#define DRM_IOCTL_RADEON_GET_TILING	DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_GET_TILING, struct drm_radeon_gem_get_tiling)
 
 typedef struct drm_radeon_init {
 	enum {
@@ -796,6 +799,24 @@ struct drm_radeon_gem_create {
 	uint32_t	flags;
 };
 
+#define RADEON_TILING_MACRO 0x1
+#define RADEON_TILING_MICRO 0x2
+#define RADEON_TILING_SWAP  0x4
+#define RADEON_TILING_SURFACE  0x8 /* this object requires a surface
+				    * when mapped - i.e. front buffer */
+
+struct drm_radeon_gem_set_tiling {
+	uint32_t	handle;
+	uint32_t	tiling_flags;
+	uint32_t	pitch;
+};
+
+struct drm_radeon_gem_get_tiling {
+	uint32_t	handle;
+	uint32_t	tiling_flags;
+	uint32_t	pitch;
+};
+
 struct drm_radeon_gem_mmap {
 	uint32_t	handle;
 	uint32_t	pad;
diff --git a/include/drm/ttm/ttm_bo_driver.h b/include/drm/ttm/ttm_bo_driver.h
index ea83dd23a4d..a68829db381 100644
--- a/include/drm/ttm/ttm_bo_driver.h
+++ b/include/drm/ttm/ttm_bo_driver.h
@@ -354,6 +354,14 @@ struct ttm_bo_driver {
 	int (*sync_obj_flush) (void *sync_obj, void *sync_arg);
 	void (*sync_obj_unref) (void **sync_obj);
 	void *(*sync_obj_ref) (void *sync_obj);
+
+	/* hook to notify driver about a driver move so it
+	 * can do tiling things */
+	void (*move_notify)(struct ttm_buffer_object *bo,
+			    struct ttm_mem_reg *new_mem);
+	/* notify the driver we are taking a fault on this BO
+	 * and have reserved it */
+	void (*fault_reserve_notify)(struct ttm_buffer_object *bo);
 };
 
 #define TTM_NUM_MEM_TYPES 8
@@ -653,6 +661,13 @@ extern int ttm_bo_device_init(struct ttm_bo_device *bdev,
 			      struct ttm_bo_driver *driver,
 			      uint64_t file_page_offset, bool need_dma32);
 
+/**
+ * ttm_bo_unmap_virtual
+ *
+ * @bo: tear down the virtual mappings for this BO
+ */
+extern void ttm_bo_unmap_virtual(struct ttm_buffer_object *bo);
+
 /**
  * ttm_bo_reserve:
  *
-- 
GitLab


From c93bb85b5cba3e3a06f2cad8e9bc5c23d3d10aac Mon Sep 17 00:00:00 2001
From: Jerome Glisse <jglisse@redhat.com>
Date: Mon, 13 Jul 2009 21:04:08 +0200
Subject: [PATCH 0205/1153] drm/radeon/kms: fix bandwidth computation on avivo
 hardware

Fix bandwidth computation and crtc priority in memory controller
so that crtc memory request are fullfill in time to avoid display
artifact.

Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/atombios_crtc.c        | 276 +++----
 drivers/gpu/drm/radeon/r100.c                 | 483 +++++++++++
 drivers/gpu/drm/radeon/r300.c                 |   1 +
 drivers/gpu/drm/radeon/r520.c                 |  14 +
 drivers/gpu/drm/radeon/radeon.h               |  40 +-
 drivers/gpu/drm/radeon/radeon_asic.h          |  13 +
 drivers/gpu/drm/radeon/radeon_device.c        |  10 +-
 drivers/gpu/drm/radeon/radeon_display.c       |  68 +-
 drivers/gpu/drm/radeon/radeon_encoders.c      | 369 +--------
 drivers/gpu/drm/radeon/radeon_legacy_crtc.c   | 661 ++++-----------
 .../gpu/drm/radeon/radeon_legacy_encoders.c   | 188 +----
 drivers/gpu/drm/radeon/radeon_mode.h          |  48 +-
 drivers/gpu/drm/radeon/radeon_share.h         |  39 +
 drivers/gpu/drm/radeon/rs400.c                |   1 +
 drivers/gpu/drm/radeon/rs600.c                |   5 +
 drivers/gpu/drm/radeon/rs690.c                | 472 +++++++++++
 drivers/gpu/drm/radeon/rs690r.h               |  99 +++
 drivers/gpu/drm/radeon/rv515.c                | 774 +++++++++++++++---
 drivers/gpu/drm/radeon/rv515r.h               | 170 ++++
 19 files changed, 2377 insertions(+), 1354 deletions(-)
 create mode 100644 drivers/gpu/drm/radeon/radeon_share.h
 create mode 100644 drivers/gpu/drm/radeon/rs690r.h
 create mode 100644 drivers/gpu/drm/radeon/rv515r.h

diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c
index eac26cdb5da..74d034f77c6 100644
--- a/drivers/gpu/drm/radeon/atombios_crtc.c
+++ b/drivers/gpu/drm/radeon/atombios_crtc.c
@@ -31,6 +31,132 @@
 #include "atom.h"
 #include "atom-bits.h"
 
+static void atombios_overscan_setup(struct drm_crtc *crtc,
+				    struct drm_display_mode *mode,
+				    struct drm_display_mode *adjusted_mode)
+{
+	struct drm_device *dev = crtc->dev;
+	struct radeon_device *rdev = dev->dev_private;
+	struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc);
+	SET_CRTC_OVERSCAN_PS_ALLOCATION args;
+	int index = GetIndexIntoMasterTable(COMMAND, SetCRTC_OverScan);
+	int a1, a2;
+
+	memset(&args, 0, sizeof(args));
+
+	args.usOverscanRight = 0;
+	args.usOverscanLeft = 0;
+	args.usOverscanBottom = 0;
+	args.usOverscanTop = 0;
+	args.ucCRTC = radeon_crtc->crtc_id;
+
+	switch (radeon_crtc->rmx_type) {
+	case RMX_CENTER:
+		args.usOverscanTop = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2;
+		args.usOverscanBottom = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2;
+		args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2;
+		args.usOverscanRight = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2;
+		atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args);
+		break;
+	case RMX_ASPECT:
+		a1 = mode->crtc_vdisplay * adjusted_mode->crtc_hdisplay;
+		a2 = adjusted_mode->crtc_vdisplay * mode->crtc_hdisplay;
+
+		if (a1 > a2) {
+			args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2;
+			args.usOverscanRight = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2;
+		} else if (a2 > a1) {
+			args.usOverscanLeft = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2;
+			args.usOverscanRight = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2;
+		}
+		atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args);
+		break;
+	case RMX_FULL:
+	default:
+		args.usOverscanRight = 0;
+		args.usOverscanLeft = 0;
+		args.usOverscanBottom = 0;
+		args.usOverscanTop = 0;
+		atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args);
+		break;
+	}
+}
+
+static void atombios_scaler_setup(struct drm_crtc *crtc)
+{
+	struct drm_device *dev = crtc->dev;
+	struct radeon_device *rdev = dev->dev_private;
+	struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc);
+	ENABLE_SCALER_PS_ALLOCATION args;
+	int index = GetIndexIntoMasterTable(COMMAND, EnableScaler);
+	/* fixme - fill in enc_priv for atom dac */
+	enum radeon_tv_std tv_std = TV_STD_NTSC;
+
+	if (!ASIC_IS_AVIVO(rdev) && radeon_crtc->crtc_id)
+		return;
+
+	memset(&args, 0, sizeof(args));
+
+	args.ucScaler = radeon_crtc->crtc_id;
+
+	if (radeon_crtc->devices & (ATOM_DEVICE_TV_SUPPORT)) {
+		switch (tv_std) {
+		case TV_STD_NTSC:
+		default:
+			args.ucTVStandard = ATOM_TV_NTSC;
+			break;
+		case TV_STD_PAL:
+			args.ucTVStandard = ATOM_TV_PAL;
+			break;
+		case TV_STD_PAL_M:
+			args.ucTVStandard = ATOM_TV_PALM;
+			break;
+		case TV_STD_PAL_60:
+			args.ucTVStandard = ATOM_TV_PAL60;
+			break;
+		case TV_STD_NTSC_J:
+			args.ucTVStandard = ATOM_TV_NTSCJ;
+			break;
+		case TV_STD_SCART_PAL:
+			args.ucTVStandard = ATOM_TV_PAL; /* ??? */
+			break;
+		case TV_STD_SECAM:
+			args.ucTVStandard = ATOM_TV_SECAM;
+			break;
+		case TV_STD_PAL_CN:
+			args.ucTVStandard = ATOM_TV_PALCN;
+			break;
+		}
+		args.ucEnable = SCALER_ENABLE_MULTITAP_MODE;
+	} else if (radeon_crtc->devices & (ATOM_DEVICE_CV_SUPPORT)) {
+		args.ucTVStandard = ATOM_TV_CV;
+		args.ucEnable = SCALER_ENABLE_MULTITAP_MODE;
+	} else {
+		switch (radeon_crtc->rmx_type) {
+		case RMX_FULL:
+			args.ucEnable = ATOM_SCALER_EXPANSION;
+			break;
+		case RMX_CENTER:
+			args.ucEnable = ATOM_SCALER_CENTER;
+			break;
+		case RMX_ASPECT:
+			args.ucEnable = ATOM_SCALER_EXPANSION;
+			break;
+		default:
+			if (ASIC_IS_AVIVO(rdev))
+				args.ucEnable = ATOM_SCALER_DISABLE;
+			else
+				args.ucEnable = ATOM_SCALER_CENTER;
+			break;
+		}
+	}
+	atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args);
+	if (radeon_crtc->devices & (ATOM_DEVICE_CV_SUPPORT | ATOM_DEVICE_TV_SUPPORT)
+	    && rdev->family >= CHIP_RV515 && rdev->family <= CHIP_RV570) {
+		atom_rv515_force_tv_scaler(rdev);
+	}
+}
+
 static void atombios_lock_crtc(struct drm_crtc *crtc, int lock)
 {
 	struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc);
@@ -522,6 +648,9 @@ int atombios_crtc_mode_set(struct drm_crtc *crtc,
 		radeon_crtc_set_base(crtc, x, y, old_fb);
 		radeon_legacy_atom_set_surface(crtc);
 	}
+	atombios_overscan_setup(crtc, mode, adjusted_mode);
+	atombios_scaler_setup(crtc);
+	radeon_bandwidth_update(rdev);
 	return 0;
 }
 
@@ -529,6 +658,8 @@ static bool atombios_crtc_mode_fixup(struct drm_crtc *crtc,
 				     struct drm_display_mode *mode,
 				     struct drm_display_mode *adjusted_mode)
 {
+	if (!radeon_crtc_scaling_mode_fixup(crtc, mode, adjusted_mode))
+		return false;
 	return true;
 }
 
@@ -561,148 +692,3 @@ void radeon_atombios_init_crtc(struct drm_device *dev,
 		    AVIVO_D2CRTC_H_TOTAL - AVIVO_D1CRTC_H_TOTAL;
 	drm_crtc_helper_add(&radeon_crtc->base, &atombios_helper_funcs);
 }
-
-void radeon_init_disp_bw_avivo(struct drm_device *dev,
-			       struct drm_display_mode *mode1,
-			       uint32_t pixel_bytes1,
-			       struct drm_display_mode *mode2,
-			       uint32_t pixel_bytes2)
-{
-	struct radeon_device *rdev = dev->dev_private;
-	fixed20_12 min_mem_eff;
-	fixed20_12 peak_disp_bw, mem_bw, pix_clk, pix_clk2, temp_ff;
-	fixed20_12 sclk_ff, mclk_ff;
-	uint32_t dc_lb_memory_split, temp;
-
-	min_mem_eff.full = rfixed_const_8(0);
-	if (rdev->disp_priority == 2) {
-		uint32_t mc_init_misc_lat_timer = 0;
-		if (rdev->family == CHIP_RV515)
-			mc_init_misc_lat_timer =
-			    RREG32_MC(RV515_MC_INIT_MISC_LAT_TIMER);
-		else if (rdev->family == CHIP_RS690)
-			mc_init_misc_lat_timer =
-			    RREG32_MC(RS690_MC_INIT_MISC_LAT_TIMER);
-
-		mc_init_misc_lat_timer &=
-		    ~(R300_MC_DISP1R_INIT_LAT_MASK <<
-		      R300_MC_DISP1R_INIT_LAT_SHIFT);
-		mc_init_misc_lat_timer &=
-		    ~(R300_MC_DISP0R_INIT_LAT_MASK <<
-		      R300_MC_DISP0R_INIT_LAT_SHIFT);
-
-		if (mode2)
-			mc_init_misc_lat_timer |=
-			    (1 << R300_MC_DISP1R_INIT_LAT_SHIFT);
-		if (mode1)
-			mc_init_misc_lat_timer |=
-			    (1 << R300_MC_DISP0R_INIT_LAT_SHIFT);
-
-		if (rdev->family == CHIP_RV515)
-			WREG32_MC(RV515_MC_INIT_MISC_LAT_TIMER,
-				  mc_init_misc_lat_timer);
-		else if (rdev->family == CHIP_RS690)
-			WREG32_MC(RS690_MC_INIT_MISC_LAT_TIMER,
-				  mc_init_misc_lat_timer);
-	}
-
-	/*
-	 * determine is there is enough bw for current mode
-	 */
-	temp_ff.full = rfixed_const(100);
-	mclk_ff.full = rfixed_const(rdev->clock.default_mclk);
-	mclk_ff.full = rfixed_div(mclk_ff, temp_ff);
-	sclk_ff.full = rfixed_const(rdev->clock.default_sclk);
-	sclk_ff.full = rfixed_div(sclk_ff, temp_ff);
-
-	temp = (rdev->mc.vram_width / 8) * (rdev->mc.vram_is_ddr ? 2 : 1);
-	temp_ff.full = rfixed_const(temp);
-	mem_bw.full = rfixed_mul(mclk_ff, temp_ff);
-	mem_bw.full = rfixed_mul(mem_bw, min_mem_eff);
-
-	pix_clk.full = 0;
-	pix_clk2.full = 0;
-	peak_disp_bw.full = 0;
-	if (mode1) {
-		temp_ff.full = rfixed_const(1000);
-		pix_clk.full = rfixed_const(mode1->clock);	/* convert to fixed point */
-		pix_clk.full = rfixed_div(pix_clk, temp_ff);
-		temp_ff.full = rfixed_const(pixel_bytes1);
-		peak_disp_bw.full += rfixed_mul(pix_clk, temp_ff);
-	}
-	if (mode2) {
-		temp_ff.full = rfixed_const(1000);
-		pix_clk2.full = rfixed_const(mode2->clock);	/* convert to fixed point */
-		pix_clk2.full = rfixed_div(pix_clk2, temp_ff);
-		temp_ff.full = rfixed_const(pixel_bytes2);
-		peak_disp_bw.full += rfixed_mul(pix_clk2, temp_ff);
-	}
-
-	if (peak_disp_bw.full >= mem_bw.full) {
-		DRM_ERROR
-		    ("You may not have enough display bandwidth for current mode\n"
-		     "If you have flickering problem, try to lower resolution, refresh rate, or color depth\n");
-		printk("peak disp bw %d, mem_bw %d\n",
-		       rfixed_trunc(peak_disp_bw), rfixed_trunc(mem_bw));
-	}
-
-	/*
-	 * Line Buffer Setup
-	 * There is a single line buffer shared by both display controllers.
-	 * DC_LB_MEMORY_SPLIT controls how that line buffer is shared between the display
-	 * controllers.  The paritioning can either be done manually or via one of four
-	 * preset allocations specified in bits 1:0:
-	 * 0 - line buffer is divided in half and shared between each display controller
-	 * 1 - D1 gets 3/4 of the line buffer, D2 gets 1/4
-	 * 2 - D1 gets the whole buffer
-	 * 3 - D1 gets 1/4 of the line buffer, D2 gets 3/4
-	 * Setting bit 2 of DC_LB_MEMORY_SPLIT controls switches to manual allocation mode.
-	 * In manual allocation mode, D1 always starts at 0, D1 end/2 is specified in bits
-	 * 14:4; D2 allocation follows D1.
-	 */
-
-	/* is auto or manual better ? */
-	dc_lb_memory_split =
-	    RREG32(AVIVO_DC_LB_MEMORY_SPLIT) & ~AVIVO_DC_LB_MEMORY_SPLIT_MASK;
-	dc_lb_memory_split &= ~AVIVO_DC_LB_MEMORY_SPLIT_SHIFT_MODE;
-#if 1
-	/* auto */
-	if (mode1 && mode2) {
-		if (mode1->hdisplay > mode2->hdisplay) {
-			if (mode1->hdisplay > 2560)
-				dc_lb_memory_split |=
-				    AVIVO_DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q;
-			else
-				dc_lb_memory_split |=
-				    AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF;
-		} else if (mode2->hdisplay > mode1->hdisplay) {
-			if (mode2->hdisplay > 2560)
-				dc_lb_memory_split |=
-				    AVIVO_DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q;
-			else
-				dc_lb_memory_split |=
-				    AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF;
-		} else
-			dc_lb_memory_split |=
-			    AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF;
-	} else if (mode1) {
-		dc_lb_memory_split |= AVIVO_DC_LB_MEMORY_SPLIT_D1_ONLY;
-	} else if (mode2) {
-		dc_lb_memory_split |= AVIVO_DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q;
-	}
-#else
-	/* manual */
-	dc_lb_memory_split |= AVIVO_DC_LB_MEMORY_SPLIT_SHIFT_MODE;
-	dc_lb_memory_split &=
-	    ~(AVIVO_DC_LB_DISP1_END_ADR_MASK <<
-	      AVIVO_DC_LB_DISP1_END_ADR_SHIFT);
-	if (mode1) {
-		dc_lb_memory_split |=
-		    ((((mode1->hdisplay / 2) + 64) & AVIVO_DC_LB_DISP1_END_ADR_MASK)
-		     << AVIVO_DC_LB_DISP1_END_ADR_SHIFT);
-	} else if (mode2) {
-		dc_lb_memory_split |= (0 << AVIVO_DC_LB_DISP1_END_ADR_SHIFT);
-	}
-#endif
-	WREG32(AVIVO_DC_LB_MEMORY_SPLIT, dc_lb_memory_split);
-}
diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index 69bd7cb5997..0e00fef0b84 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -1784,3 +1784,486 @@ void r100_clear_surface_reg(struct radeon_device *rdev, int reg)
 	int surf_index = reg * 16;
 	WREG32(RADEON_SURFACE0_INFO + surf_index, 0);
 }
+
+void r100_bandwidth_update(struct radeon_device *rdev)
+{
+	fixed20_12 trcd_ff, trp_ff, tras_ff, trbs_ff, tcas_ff;
+	fixed20_12 sclk_ff, mclk_ff, sclk_eff_ff, sclk_delay_ff;
+	fixed20_12 peak_disp_bw, mem_bw, pix_clk, pix_clk2, temp_ff, crit_point_ff;
+	uint32_t temp, data, mem_trcd, mem_trp, mem_tras;
+	fixed20_12 memtcas_ff[8] = {
+		fixed_init(1),
+		fixed_init(2),
+		fixed_init(3),
+		fixed_init(0),
+		fixed_init_half(1),
+		fixed_init_half(2),
+		fixed_init(0),
+	};
+	fixed20_12 memtcas_rs480_ff[8] = {
+		fixed_init(0),
+		fixed_init(1),
+		fixed_init(2),
+		fixed_init(3),
+		fixed_init(0),
+		fixed_init_half(1),
+		fixed_init_half(2),
+		fixed_init_half(3),
+	};
+	fixed20_12 memtcas2_ff[8] = {
+		fixed_init(0),
+		fixed_init(1),
+		fixed_init(2),
+		fixed_init(3),
+		fixed_init(4),
+		fixed_init(5),
+		fixed_init(6),
+		fixed_init(7),
+	};
+	fixed20_12 memtrbs[8] = {
+		fixed_init(1),
+		fixed_init_half(1),
+		fixed_init(2),
+		fixed_init_half(2),
+		fixed_init(3),
+		fixed_init_half(3),
+		fixed_init(4),
+		fixed_init_half(4)
+	};
+	fixed20_12 memtrbs_r4xx[8] = {
+		fixed_init(4),
+		fixed_init(5),
+		fixed_init(6),
+		fixed_init(7),
+		fixed_init(8),
+		fixed_init(9),
+		fixed_init(10),
+		fixed_init(11)
+	};
+	fixed20_12 min_mem_eff;
+	fixed20_12 mc_latency_sclk, mc_latency_mclk, k1;
+	fixed20_12 cur_latency_mclk, cur_latency_sclk;
+	fixed20_12 disp_latency, disp_latency_overhead, disp_drain_rate,
+		disp_drain_rate2, read_return_rate;
+	fixed20_12 time_disp1_drop_priority;
+	int c;
+	int cur_size = 16;       /* in octawords */
+	int critical_point = 0, critical_point2;
+/* 	uint32_t read_return_rate, time_disp1_drop_priority; */
+	int stop_req, max_stop_req;
+	struct drm_display_mode *mode1 = NULL;
+	struct drm_display_mode *mode2 = NULL;
+	uint32_t pixel_bytes1 = 0;
+	uint32_t pixel_bytes2 = 0;
+
+	if (rdev->mode_info.crtcs[0]->base.enabled) {
+		mode1 = &rdev->mode_info.crtcs[0]->base.mode;
+		pixel_bytes1 = rdev->mode_info.crtcs[0]->base.fb->bits_per_pixel / 8;
+	}
+	if (rdev->mode_info.crtcs[1]->base.enabled) {
+		mode2 = &rdev->mode_info.crtcs[1]->base.mode;
+		pixel_bytes2 = rdev->mode_info.crtcs[1]->base.fb->bits_per_pixel / 8;
+	}
+
+	min_mem_eff.full = rfixed_const_8(0);
+	/* get modes */
+	if ((rdev->disp_priority == 2) && ASIC_IS_R300(rdev)) {
+		uint32_t mc_init_misc_lat_timer = RREG32(R300_MC_INIT_MISC_LAT_TIMER);
+		mc_init_misc_lat_timer &= ~(R300_MC_DISP1R_INIT_LAT_MASK << R300_MC_DISP1R_INIT_LAT_SHIFT);
+		mc_init_misc_lat_timer &= ~(R300_MC_DISP0R_INIT_LAT_MASK << R300_MC_DISP0R_INIT_LAT_SHIFT);
+		/* check crtc enables */
+		if (mode2)
+			mc_init_misc_lat_timer |= (1 << R300_MC_DISP1R_INIT_LAT_SHIFT);
+		if (mode1)
+			mc_init_misc_lat_timer |= (1 << R300_MC_DISP0R_INIT_LAT_SHIFT);
+		WREG32(R300_MC_INIT_MISC_LAT_TIMER, mc_init_misc_lat_timer);
+	}
+
+	/*
+	 * determine is there is enough bw for current mode
+	 */
+	mclk_ff.full = rfixed_const(rdev->clock.default_mclk);
+	temp_ff.full = rfixed_const(100);
+	mclk_ff.full = rfixed_div(mclk_ff, temp_ff);
+	sclk_ff.full = rfixed_const(rdev->clock.default_sclk);
+	sclk_ff.full = rfixed_div(sclk_ff, temp_ff);
+
+	temp = (rdev->mc.vram_width / 8) * (rdev->mc.vram_is_ddr ? 2 : 1);
+	temp_ff.full = rfixed_const(temp);
+	mem_bw.full = rfixed_mul(mclk_ff, temp_ff);
+
+	pix_clk.full = 0;
+	pix_clk2.full = 0;
+	peak_disp_bw.full = 0;
+	if (mode1) {
+		temp_ff.full = rfixed_const(1000);
+		pix_clk.full = rfixed_const(mode1->clock); /* convert to fixed point */
+		pix_clk.full = rfixed_div(pix_clk, temp_ff);
+		temp_ff.full = rfixed_const(pixel_bytes1);
+		peak_disp_bw.full += rfixed_mul(pix_clk, temp_ff);
+	}
+	if (mode2) {
+		temp_ff.full = rfixed_const(1000);
+		pix_clk2.full = rfixed_const(mode2->clock); /* convert to fixed point */
+		pix_clk2.full = rfixed_div(pix_clk2, temp_ff);
+		temp_ff.full = rfixed_const(pixel_bytes2);
+		peak_disp_bw.full += rfixed_mul(pix_clk2, temp_ff);
+	}
+
+	mem_bw.full = rfixed_mul(mem_bw, min_mem_eff);
+	if (peak_disp_bw.full >= mem_bw.full) {
+		DRM_ERROR("You may not have enough display bandwidth for current mode\n"
+			  "If you have flickering problem, try to lower resolution, refresh rate, or color depth\n");
+	}
+
+	/*  Get values from the EXT_MEM_CNTL register...converting its contents. */
+	temp = RREG32(RADEON_MEM_TIMING_CNTL);
+	if ((rdev->family == CHIP_RV100) || (rdev->flags & RADEON_IS_IGP)) { /* RV100, M6, IGPs */
+		mem_trcd = ((temp >> 2) & 0x3) + 1;
+		mem_trp  = ((temp & 0x3)) + 1;
+		mem_tras = ((temp & 0x70) >> 4) + 1;
+	} else if (rdev->family == CHIP_R300 ||
+		   rdev->family == CHIP_R350) { /* r300, r350 */
+		mem_trcd = (temp & 0x7) + 1;
+		mem_trp = ((temp >> 8) & 0x7) + 1;
+		mem_tras = ((temp >> 11) & 0xf) + 4;
+	} else if (rdev->family == CHIP_RV350 ||
+		   rdev->family <= CHIP_RV380) {
+		/* rv3x0 */
+		mem_trcd = (temp & 0x7) + 3;
+		mem_trp = ((temp >> 8) & 0x7) + 3;
+		mem_tras = ((temp >> 11) & 0xf) + 6;
+	} else if (rdev->family == CHIP_R420 ||
+		   rdev->family == CHIP_R423 ||
+		   rdev->family == CHIP_RV410) {
+		/* r4xx */
+		mem_trcd = (temp & 0xf) + 3;
+		if (mem_trcd > 15)
+			mem_trcd = 15;
+		mem_trp = ((temp >> 8) & 0xf) + 3;
+		if (mem_trp > 15)
+			mem_trp = 15;
+		mem_tras = ((temp >> 12) & 0x1f) + 6;
+		if (mem_tras > 31)
+			mem_tras = 31;
+	} else { /* RV200, R200 */
+		mem_trcd = (temp & 0x7) + 1;
+		mem_trp = ((temp >> 8) & 0x7) + 1;
+		mem_tras = ((temp >> 12) & 0xf) + 4;
+	}
+	/* convert to FF */
+	trcd_ff.full = rfixed_const(mem_trcd);
+	trp_ff.full = rfixed_const(mem_trp);
+	tras_ff.full = rfixed_const(mem_tras);
+
+	/* Get values from the MEM_SDRAM_MODE_REG register...converting its */
+	temp = RREG32(RADEON_MEM_SDRAM_MODE_REG);
+	data = (temp & (7 << 20)) >> 20;
+	if ((rdev->family == CHIP_RV100) || rdev->flags & RADEON_IS_IGP) {
+		if (rdev->family == CHIP_RS480) /* don't think rs400 */
+			tcas_ff = memtcas_rs480_ff[data];
+		else
+			tcas_ff = memtcas_ff[data];
+	} else
+		tcas_ff = memtcas2_ff[data];
+
+	if (rdev->family == CHIP_RS400 ||
+	    rdev->family == CHIP_RS480) {
+		/* extra cas latency stored in bits 23-25 0-4 clocks */
+		data = (temp >> 23) & 0x7;
+		if (data < 5)
+			tcas_ff.full += rfixed_const(data);
+	}
+
+	if (ASIC_IS_R300(rdev) && !(rdev->flags & RADEON_IS_IGP)) {
+		/* on the R300, Tcas is included in Trbs.
+		 */
+		temp = RREG32(RADEON_MEM_CNTL);
+		data = (R300_MEM_NUM_CHANNELS_MASK & temp);
+		if (data == 1) {
+			if (R300_MEM_USE_CD_CH_ONLY & temp) {
+				temp = RREG32(R300_MC_IND_INDEX);
+				temp &= ~R300_MC_IND_ADDR_MASK;
+				temp |= R300_MC_READ_CNTL_CD_mcind;
+				WREG32(R300_MC_IND_INDEX, temp);
+				temp = RREG32(R300_MC_IND_DATA);
+				data = (R300_MEM_RBS_POSITION_C_MASK & temp);
+			} else {
+				temp = RREG32(R300_MC_READ_CNTL_AB);
+				data = (R300_MEM_RBS_POSITION_A_MASK & temp);
+			}
+		} else {
+			temp = RREG32(R300_MC_READ_CNTL_AB);
+			data = (R300_MEM_RBS_POSITION_A_MASK & temp);
+		}
+		if (rdev->family == CHIP_RV410 ||
+		    rdev->family == CHIP_R420 ||
+		    rdev->family == CHIP_R423)
+			trbs_ff = memtrbs_r4xx[data];
+		else
+			trbs_ff = memtrbs[data];
+		tcas_ff.full += trbs_ff.full;
+	}
+
+	sclk_eff_ff.full = sclk_ff.full;
+
+	if (rdev->flags & RADEON_IS_AGP) {
+		fixed20_12 agpmode_ff;
+		agpmode_ff.full = rfixed_const(radeon_agpmode);
+		temp_ff.full = rfixed_const_666(16);
+		sclk_eff_ff.full -= rfixed_mul(agpmode_ff, temp_ff);
+	}
+	/* TODO PCIE lanes may affect this - agpmode == 16?? */
+
+	if (ASIC_IS_R300(rdev)) {
+		sclk_delay_ff.full = rfixed_const(250);
+	} else {
+		if ((rdev->family == CHIP_RV100) ||
+		    rdev->flags & RADEON_IS_IGP) {
+			if (rdev->mc.vram_is_ddr)
+				sclk_delay_ff.full = rfixed_const(41);
+			else
+				sclk_delay_ff.full = rfixed_const(33);
+		} else {
+			if (rdev->mc.vram_width == 128)
+				sclk_delay_ff.full = rfixed_const(57);
+			else
+				sclk_delay_ff.full = rfixed_const(41);
+		}
+	}
+
+	mc_latency_sclk.full = rfixed_div(sclk_delay_ff, sclk_eff_ff);
+
+	if (rdev->mc.vram_is_ddr) {
+		if (rdev->mc.vram_width == 32) {
+			k1.full = rfixed_const(40);
+			c  = 3;
+		} else {
+			k1.full = rfixed_const(20);
+			c  = 1;
+		}
+	} else {
+		k1.full = rfixed_const(40);
+		c  = 3;
+	}
+
+	temp_ff.full = rfixed_const(2);
+	mc_latency_mclk.full = rfixed_mul(trcd_ff, temp_ff);
+	temp_ff.full = rfixed_const(c);
+	mc_latency_mclk.full += rfixed_mul(tcas_ff, temp_ff);
+	temp_ff.full = rfixed_const(4);
+	mc_latency_mclk.full += rfixed_mul(tras_ff, temp_ff);
+	mc_latency_mclk.full += rfixed_mul(trp_ff, temp_ff);
+	mc_latency_mclk.full += k1.full;
+
+	mc_latency_mclk.full = rfixed_div(mc_latency_mclk, mclk_ff);
+	mc_latency_mclk.full += rfixed_div(temp_ff, sclk_eff_ff);
+
+	/*
+	  HW cursor time assuming worst case of full size colour cursor.
+	*/
+	temp_ff.full = rfixed_const((2 * (cur_size - (rdev->mc.vram_is_ddr + 1))));
+	temp_ff.full += trcd_ff.full;
+	if (temp_ff.full < tras_ff.full)
+		temp_ff.full = tras_ff.full;
+	cur_latency_mclk.full = rfixed_div(temp_ff, mclk_ff);
+
+	temp_ff.full = rfixed_const(cur_size);
+	cur_latency_sclk.full = rfixed_div(temp_ff, sclk_eff_ff);
+	/*
+	  Find the total latency for the display data.
+	*/
+	disp_latency_overhead.full = rfixed_const(80);
+	disp_latency_overhead.full = rfixed_div(disp_latency_overhead, sclk_ff);
+	mc_latency_mclk.full += disp_latency_overhead.full + cur_latency_mclk.full;
+	mc_latency_sclk.full += disp_latency_overhead.full + cur_latency_sclk.full;
+
+	if (mc_latency_mclk.full > mc_latency_sclk.full)
+		disp_latency.full = mc_latency_mclk.full;
+	else
+		disp_latency.full = mc_latency_sclk.full;
+
+	/* setup Max GRPH_STOP_REQ default value */
+	if (ASIC_IS_RV100(rdev))
+		max_stop_req = 0x5c;
+	else
+		max_stop_req = 0x7c;
+
+	if (mode1) {
+		/*  CRTC1
+		    Set GRPH_BUFFER_CNTL register using h/w defined optimal values.
+		    GRPH_STOP_REQ <= MIN[ 0x7C, (CRTC_H_DISP + 1) * (bit depth) / 0x10 ]
+		*/
+		stop_req = mode1->hdisplay * pixel_bytes1 / 16;
+
+		if (stop_req > max_stop_req)
+			stop_req = max_stop_req;
+
+		/*
+		  Find the drain rate of the display buffer.
+		*/
+		temp_ff.full = rfixed_const((16/pixel_bytes1));
+		disp_drain_rate.full = rfixed_div(pix_clk, temp_ff);
+
+		/*
+		  Find the critical point of the display buffer.
+		*/
+		crit_point_ff.full = rfixed_mul(disp_drain_rate, disp_latency);
+		crit_point_ff.full += rfixed_const_half(0);
+
+		critical_point = rfixed_trunc(crit_point_ff);
+
+		if (rdev->disp_priority == 2) {
+			critical_point = 0;
+		}
+
+		/*
+		  The critical point should never be above max_stop_req-4.  Setting
+		  GRPH_CRITICAL_CNTL = 0 will thus force high priority all the time.
+		*/
+		if (max_stop_req - critical_point < 4)
+			critical_point = 0;
+
+		if (critical_point == 0 && mode2 && rdev->family == CHIP_R300) {
+			/* some R300 cards have problem with this set to 0, when CRTC2 is enabled.*/
+			critical_point = 0x10;
+		}
+
+		temp = RREG32(RADEON_GRPH_BUFFER_CNTL);
+		temp &= ~(RADEON_GRPH_STOP_REQ_MASK);
+		temp |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT);
+		temp &= ~(RADEON_GRPH_START_REQ_MASK);
+		if ((rdev->family == CHIP_R350) &&
+		    (stop_req > 0x15)) {
+			stop_req -= 0x10;
+		}
+		temp |= (stop_req << RADEON_GRPH_START_REQ_SHIFT);
+		temp |= RADEON_GRPH_BUFFER_SIZE;
+		temp &= ~(RADEON_GRPH_CRITICAL_CNTL   |
+			  RADEON_GRPH_CRITICAL_AT_SOF |
+			  RADEON_GRPH_STOP_CNTL);
+		/*
+		  Write the result into the register.
+		*/
+		WREG32(RADEON_GRPH_BUFFER_CNTL, ((temp & ~RADEON_GRPH_CRITICAL_POINT_MASK) |
+						       (critical_point << RADEON_GRPH_CRITICAL_POINT_SHIFT)));
+
+#if 0
+		if ((rdev->family == CHIP_RS400) ||
+		    (rdev->family == CHIP_RS480)) {
+			/* attempt to program RS400 disp regs correctly ??? */
+			temp = RREG32(RS400_DISP1_REG_CNTL);
+			temp &= ~(RS400_DISP1_START_REQ_LEVEL_MASK |
+				  RS400_DISP1_STOP_REQ_LEVEL_MASK);
+			WREG32(RS400_DISP1_REQ_CNTL1, (temp |
+						       (critical_point << RS400_DISP1_START_REQ_LEVEL_SHIFT) |
+						       (critical_point << RS400_DISP1_STOP_REQ_LEVEL_SHIFT)));
+			temp = RREG32(RS400_DMIF_MEM_CNTL1);
+			temp &= ~(RS400_DISP1_CRITICAL_POINT_START_MASK |
+				  RS400_DISP1_CRITICAL_POINT_STOP_MASK);
+			WREG32(RS400_DMIF_MEM_CNTL1, (temp |
+						      (critical_point << RS400_DISP1_CRITICAL_POINT_START_SHIFT) |
+						      (critical_point << RS400_DISP1_CRITICAL_POINT_STOP_SHIFT)));
+		}
+#endif
+
+		DRM_DEBUG("GRPH_BUFFER_CNTL from to %x\n",
+			  /* 	  (unsigned int)info->SavedReg->grph_buffer_cntl, */
+			  (unsigned int)RREG32(RADEON_GRPH_BUFFER_CNTL));
+	}
+
+	if (mode2) {
+		u32 grph2_cntl;
+		stop_req = mode2->hdisplay * pixel_bytes2 / 16;
+
+		if (stop_req > max_stop_req)
+			stop_req = max_stop_req;
+
+		/*
+		  Find the drain rate of the display buffer.
+		*/
+		temp_ff.full = rfixed_const((16/pixel_bytes2));
+		disp_drain_rate2.full = rfixed_div(pix_clk2, temp_ff);
+
+		grph2_cntl = RREG32(RADEON_GRPH2_BUFFER_CNTL);
+		grph2_cntl &= ~(RADEON_GRPH_STOP_REQ_MASK);
+		grph2_cntl |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT);
+		grph2_cntl &= ~(RADEON_GRPH_START_REQ_MASK);
+		if ((rdev->family == CHIP_R350) &&
+		    (stop_req > 0x15)) {
+			stop_req -= 0x10;
+		}
+		grph2_cntl |= (stop_req << RADEON_GRPH_START_REQ_SHIFT);
+		grph2_cntl |= RADEON_GRPH_BUFFER_SIZE;
+		grph2_cntl &= ~(RADEON_GRPH_CRITICAL_CNTL   |
+			  RADEON_GRPH_CRITICAL_AT_SOF |
+			  RADEON_GRPH_STOP_CNTL);
+
+		if ((rdev->family == CHIP_RS100) ||
+		    (rdev->family == CHIP_RS200))
+			critical_point2 = 0;
+		else {
+			temp = (rdev->mc.vram_width * rdev->mc.vram_is_ddr + 1)/128;
+			temp_ff.full = rfixed_const(temp);
+			temp_ff.full = rfixed_mul(mclk_ff, temp_ff);
+			if (sclk_ff.full < temp_ff.full)
+				temp_ff.full = sclk_ff.full;
+
+			read_return_rate.full = temp_ff.full;
+
+			if (mode1) {
+				temp_ff.full = read_return_rate.full - disp_drain_rate.full;
+				time_disp1_drop_priority.full = rfixed_div(crit_point_ff, temp_ff);
+			} else {
+				time_disp1_drop_priority.full = 0;
+			}
+			crit_point_ff.full = disp_latency.full + time_disp1_drop_priority.full + disp_latency.full;
+			crit_point_ff.full = rfixed_mul(crit_point_ff, disp_drain_rate2);
+			crit_point_ff.full += rfixed_const_half(0);
+
+			critical_point2 = rfixed_trunc(crit_point_ff);
+
+			if (rdev->disp_priority == 2) {
+				critical_point2 = 0;
+			}
+
+			if (max_stop_req - critical_point2 < 4)
+				critical_point2 = 0;
+
+		}
+
+		if (critical_point2 == 0 && rdev->family == CHIP_R300) {
+			/* some R300 cards have problem with this set to 0 */
+			critical_point2 = 0x10;
+		}
+
+		WREG32(RADEON_GRPH2_BUFFER_CNTL, ((grph2_cntl & ~RADEON_GRPH_CRITICAL_POINT_MASK) |
+						  (critical_point2 << RADEON_GRPH_CRITICAL_POINT_SHIFT)));
+
+		if ((rdev->family == CHIP_RS400) ||
+		    (rdev->family == CHIP_RS480)) {
+#if 0
+			/* attempt to program RS400 disp2 regs correctly ??? */
+			temp = RREG32(RS400_DISP2_REQ_CNTL1);
+			temp &= ~(RS400_DISP2_START_REQ_LEVEL_MASK |
+				  RS400_DISP2_STOP_REQ_LEVEL_MASK);
+			WREG32(RS400_DISP2_REQ_CNTL1, (temp |
+						       (critical_point2 << RS400_DISP1_START_REQ_LEVEL_SHIFT) |
+						       (critical_point2 << RS400_DISP1_STOP_REQ_LEVEL_SHIFT)));
+			temp = RREG32(RS400_DISP2_REQ_CNTL2);
+			temp &= ~(RS400_DISP2_CRITICAL_POINT_START_MASK |
+				  RS400_DISP2_CRITICAL_POINT_STOP_MASK);
+			WREG32(RS400_DISP2_REQ_CNTL2, (temp |
+						       (critical_point2 << RS400_DISP2_CRITICAL_POINT_START_SHIFT) |
+						       (critical_point2 << RS400_DISP2_CRITICAL_POINT_STOP_SHIFT)));
+#endif
+			WREG32(RS400_DISP2_REQ_CNTL1, 0x105DC1CC);
+			WREG32(RS400_DISP2_REQ_CNTL2, 0x2749D000);
+			WREG32(RS400_DMIF_MEM_CNTL1,  0x29CA71DC);
+			WREG32(RS400_DISP1_REQ_CNTL1, 0x28FBC3AC);
+		}
+
+		DRM_DEBUG("GRPH2_BUFFER_CNTL from to %x\n",
+			  (unsigned int)RREG32(RADEON_GRPH2_BUFFER_CNTL));
+	}
+}
diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c
index 28e5777658b..9c8d41534a5 100644
--- a/drivers/gpu/drm/radeon/r300.c
+++ b/drivers/gpu/drm/radeon/r300.c
@@ -31,6 +31,7 @@
 #include "radeon_reg.h"
 #include "radeon.h"
 #include "radeon_drm.h"
+#include "radeon_share.h"
 
 /* r300,r350,rv350,rv370,rv380 depends on : */
 void r100_hdp_reset(struct radeon_device *rdev);
diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c
index b6bd3758db6..0a981e2ee2f 100644
--- a/drivers/gpu/drm/radeon/r520.c
+++ b/drivers/gpu/drm/radeon/r520.c
@@ -28,6 +28,7 @@
 #include "drmP.h"
 #include "radeon_reg.h"
 #include "radeon.h"
+#include "radeon_share.h"
 
 /* r520,rv530,rv560,rv570,r580 depends on : */
 void r100_hdp_reset(struct radeon_device *rdev);
@@ -226,7 +227,20 @@ static void r520_vram_get_type(struct radeon_device *rdev)
 
 void r520_vram_info(struct radeon_device *rdev)
 {
+	fixed20_12 a;
+
 	r520_vram_get_type(rdev);
 
 	r100_vram_init_sizes(rdev);
+	/* FIXME: we should enforce default clock in case GPU is not in
+	 * default setup
+	 */
+	a.full = rfixed_const(100);
+	rdev->pm.sclk.full = rfixed_const(rdev->clock.default_sclk);
+	rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a);
+}
+
+void r520_bandwidth_update(struct radeon_device *rdev)
+{
+	rv515_bandwidth_avivo_update(rdev);
 }
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index af12a2fe322..63a3fe32e58 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -113,6 +113,7 @@ enum radeon_family {
 	CHIP_RV770,
 	CHIP_RV730,
 	CHIP_RV710,
+	CHIP_RS880,
 	CHIP_LAST,
 };
 
@@ -490,6 +491,39 @@ struct radeon_wb {
 	uint64_t		gpu_addr;
 };
 
+/**
+ * struct radeon_pm - power management datas
+ * @max_bandwidth:      maximum bandwidth the gpu has (MByte/s)
+ * @igp_sideport_mclk:  sideport memory clock Mhz (rs690,rs740,rs780,rs880)
+ * @igp_system_mclk:    system clock Mhz (rs690,rs740,rs780,rs880)
+ * @igp_ht_link_clk:    ht link clock Mhz (rs690,rs740,rs780,rs880)
+ * @igp_ht_link_width:  ht link width in bits (rs690,rs740,rs780,rs880)
+ * @k8_bandwidth:       k8 bandwidth the gpu has (MByte/s) (IGP)
+ * @sideport_bandwidth: sideport bandwidth the gpu has (MByte/s) (IGP)
+ * @ht_bandwidth:       ht bandwidth the gpu has (MByte/s) (IGP)
+ * @core_bandwidth:     core GPU bandwidth the gpu has (MByte/s) (IGP)
+ * @sclk:          	GPU clock Mhz (core bandwith depends of this clock)
+ * @needed_bandwidth:   current bandwidth needs
+ *
+ * It keeps track of various data needed to take powermanagement decision.
+ * Bandwith need is used to determine minimun clock of the GPU and memory.
+ * Equation between gpu/memory clock and available bandwidth is hw dependent
+ * (type of memory, bus size, efficiency, ...)
+ */
+struct radeon_pm {
+	fixed20_12		max_bandwidth;
+	fixed20_12		igp_sideport_mclk;
+	fixed20_12		igp_system_mclk;
+	fixed20_12		igp_ht_link_clk;
+	fixed20_12		igp_ht_link_width;
+	fixed20_12		k8_bandwidth;
+	fixed20_12		sideport_bandwidth;
+	fixed20_12		ht_bandwidth;
+	fixed20_12		core_bandwidth;
+	fixed20_12		sclk;
+	fixed20_12		needed_bandwidth;
+};
+
 
 /*
  * Benchmarking
@@ -551,19 +585,17 @@ struct radeon_asic {
 	void (*set_memory_clock)(struct radeon_device *rdev, uint32_t mem_clock);
 	void (*set_pcie_lanes)(struct radeon_device *rdev, int lanes);
 	void (*set_clock_gating)(struct radeon_device *rdev, int enable);
-
 	int (*set_surface_reg)(struct radeon_device *rdev, int reg,
 			       uint32_t tiling_flags, uint32_t pitch,
 			       uint32_t offset, uint32_t obj_size);
 	int (*clear_surface_reg)(struct radeon_device *rdev, int reg);
+	void (*bandwidth_update)(struct radeon_device *rdev);
 };
 
 union radeon_asic_config {
 	struct r300_asic	r300;
 };
 
-/* r100 */
-void r100_vram_init_sizes(struct radeon_device *rdev);
 
 /*
  * IOCTL.
@@ -646,6 +678,7 @@ struct radeon_device {
 	struct radeon_irq		irq;
 	struct radeon_asic		*asic;
 	struct radeon_gem		gem;
+	struct radeon_pm		pm;
 	struct mutex			cs_mutex;
 	struct radeon_wb		wb;
 	bool				gpu_lockup;
@@ -829,5 +862,6 @@ static inline void radeon_ring_write(struct radeon_device *rdev, uint32_t v)
 #define radeon_set_clock_gating(rdev, e) (rdev)->asic->set_clock_gating((rdev), (e))
 #define radeon_set_surface_reg(rdev, r, f, p, o, s) ((rdev)->asic->set_surface_reg((rdev), (r), (f), (p), (o), (s)))
 #define radeon_clear_surface_reg(rdev, r) ((rdev)->asic->clear_surface_reg((rdev), (r)))
+#define radeon_bandwidth_update(rdev) (rdev)->asic->bandwidth_update((rdev))
 
 #endif
diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h
index dd903d32940..9a75876e0c3 100644
--- a/drivers/gpu/drm/radeon/radeon_asic.h
+++ b/drivers/gpu/drm/radeon/radeon_asic.h
@@ -75,6 +75,7 @@ int r100_set_surface_reg(struct radeon_device *rdev, int reg,
 			 uint32_t tiling_flags, uint32_t pitch,
 			 uint32_t offset, uint32_t obj_size);
 int r100_clear_surface_reg(struct radeon_device *rdev, int reg);
+void r100_bandwidth_update(struct radeon_device *rdev);
 
 static struct radeon_asic r100_asic = {
 	.init = &r100_init,
@@ -106,6 +107,7 @@ static struct radeon_asic r100_asic = {
 	.set_clock_gating = &radeon_legacy_set_clock_gating,
 	.set_surface_reg = r100_set_surface_reg,
 	.clear_surface_reg = r100_clear_surface_reg,
+	.bandwidth_update = &r100_bandwidth_update,
 };
 
 
@@ -165,6 +167,7 @@ static struct radeon_asic r300_asic = {
 	.set_clock_gating = &radeon_legacy_set_clock_gating,
 	.set_surface_reg = r100_set_surface_reg,
 	.clear_surface_reg = r100_clear_surface_reg,
+	.bandwidth_update = &r100_bandwidth_update,
 };
 
 /*
@@ -204,6 +207,7 @@ static struct radeon_asic r420_asic = {
 	.set_clock_gating = &radeon_atom_set_clock_gating,
 	.set_surface_reg = r100_set_surface_reg,
 	.clear_surface_reg = r100_clear_surface_reg,
+	.bandwidth_update = &r100_bandwidth_update,
 };
 
 
@@ -250,6 +254,7 @@ static struct radeon_asic rs400_asic = {
 	.set_clock_gating = &radeon_legacy_set_clock_gating,
 	.set_surface_reg = r100_set_surface_reg,
 	.clear_surface_reg = r100_clear_surface_reg,
+	.bandwidth_update = &r100_bandwidth_update,
 };
 
 
@@ -267,6 +272,7 @@ void rs600_gart_tlb_flush(struct radeon_device *rdev);
 int rs600_gart_set_page(struct radeon_device *rdev, int i, uint64_t addr);
 uint32_t rs600_mc_rreg(struct radeon_device *rdev, uint32_t reg);
 void rs600_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v);
+void rs600_bandwidth_update(struct radeon_device *rdev);
 static struct radeon_asic rs600_asic = {
 	.init = &r300_init,
 	.errata = &rs600_errata,
@@ -295,6 +301,7 @@ static struct radeon_asic rs600_asic = {
 	.set_memory_clock = &radeon_atom_set_memory_clock,
 	.set_pcie_lanes = NULL,
 	.set_clock_gating = &radeon_atom_set_clock_gating,
+	.bandwidth_update = &rs600_bandwidth_update,
 };
 
 
@@ -307,6 +314,7 @@ int rs690_mc_init(struct radeon_device *rdev);
 void rs690_mc_fini(struct radeon_device *rdev);
 uint32_t rs690_mc_rreg(struct radeon_device *rdev, uint32_t reg);
 void rs690_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v);
+void rs690_bandwidth_update(struct radeon_device *rdev);
 static struct radeon_asic rs690_asic = {
 	.init = &r300_init,
 	.errata = &rs690_errata,
@@ -337,6 +345,7 @@ static struct radeon_asic rs690_asic = {
 	.set_clock_gating = &radeon_atom_set_clock_gating,
 	.set_surface_reg = r100_set_surface_reg,
 	.clear_surface_reg = r100_clear_surface_reg,
+	.bandwidth_update = &rs690_bandwidth_update,
 };
 
 
@@ -354,6 +363,7 @@ void rv515_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v);
 void rv515_ring_start(struct radeon_device *rdev);
 uint32_t rv515_pcie_rreg(struct radeon_device *rdev, uint32_t reg);
 void rv515_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v);
+void rv515_bandwidth_update(struct radeon_device *rdev);
 static struct radeon_asic rv515_asic = {
 	.init = &rv515_init,
 	.errata = &rv515_errata,
@@ -384,6 +394,7 @@ static struct radeon_asic rv515_asic = {
 	.set_clock_gating = &radeon_atom_set_clock_gating,
 	.set_surface_reg = r100_set_surface_reg,
 	.clear_surface_reg = r100_clear_surface_reg,
+	.bandwidth_update = &rv515_bandwidth_update,
 };
 
 
@@ -394,6 +405,7 @@ void r520_errata(struct radeon_device *rdev);
 void r520_vram_info(struct radeon_device *rdev);
 int r520_mc_init(struct radeon_device *rdev);
 void r520_mc_fini(struct radeon_device *rdev);
+void r520_bandwidth_update(struct radeon_device *rdev);
 static struct radeon_asic r520_asic = {
 	.init = &rv515_init,
 	.errata = &r520_errata,
@@ -424,6 +436,7 @@ static struct radeon_asic r520_asic = {
 	.set_clock_gating = &radeon_atom_set_clock_gating,
 	.set_surface_reg = r100_set_surface_reg,
 	.clear_surface_reg = r100_clear_surface_reg,
+	.bandwidth_update = &r520_bandwidth_update,
 };
 
 /*
diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c
index f23083bbba3..f78db5c8008 100644
--- a/drivers/gpu/drm/radeon/radeon_device.c
+++ b/drivers/gpu/drm/radeon/radeon_device.c
@@ -561,6 +561,11 @@ int radeon_device_init(struct radeon_device *rdev,
 			radeon_combios_asic_init(rdev->ddev);
 		}
 	}
+	/* Initialize clocks */
+	r = radeon_clocks_init(rdev);
+	if (r) {
+		return r;
+	}
 	/* Get vram informations */
 	radeon_vram_info(rdev);
 
@@ -572,11 +577,6 @@ int radeon_device_init(struct radeon_device *rdev,
 		 (unsigned)rdev->mc.aper_size >> 20);
 	DRM_INFO("RAM width %dbits %cDR\n",
 		 rdev->mc.vram_width, rdev->mc.vram_is_ddr ? 'D' : 'S');
-	/* Initialize clocks */
-	r = radeon_clocks_init(rdev);
-	if (r) {
-		return r;
-	}
 	/* Initialize memory controller (also test AGP) */
 	r = radeon_mc_init(rdev);
 	if (r) {
diff --git a/drivers/gpu/drm/radeon/radeon_display.c b/drivers/gpu/drm/radeon/radeon_display.c
index bc312f3d9a0..a8fa1bb84cf 100644
--- a/drivers/gpu/drm/radeon/radeon_display.c
+++ b/drivers/gpu/drm/radeon/radeon_display.c
@@ -187,6 +187,7 @@ static void radeon_crtc_init(struct drm_device *dev, int index)
 
 	drm_mode_crtc_set_gamma_size(&radeon_crtc->base, 256);
 	radeon_crtc->crtc_id = index;
+	rdev->mode_info.crtcs[index] = radeon_crtc;
 
 	radeon_crtc->mode_set.crtc = &radeon_crtc->base;
 	radeon_crtc->mode_set.connectors = (struct drm_connector **)(radeon_crtc + 1);
@@ -661,36 +662,51 @@ void radeon_modeset_fini(struct radeon_device *rdev)
 	}
 }
 
-void radeon_init_disp_bandwidth(struct drm_device *dev)
+bool radeon_crtc_scaling_mode_fixup(struct drm_crtc *crtc,
+				struct drm_display_mode *mode,
+				struct drm_display_mode *adjusted_mode)
 {
-	struct radeon_device *rdev = dev->dev_private;
-	struct drm_display_mode *modes[2];
-	int pixel_bytes[2];
-	struct drm_crtc *crtc;
-
-	pixel_bytes[0] = pixel_bytes[1] = 0;
-	modes[0] = modes[1] = NULL;
-
-	list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
-		struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc);
+	struct drm_device *dev = crtc->dev;
+	struct drm_encoder *encoder;
+	struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc);
+	struct radeon_encoder *radeon_encoder;
+	bool first = true;
 
-		if (crtc->enabled && crtc->fb) {
-			modes[radeon_crtc->crtc_id] = &crtc->mode;
-			pixel_bytes[radeon_crtc->crtc_id] = crtc->fb->bits_per_pixel / 8;
+	list_for_each_entry(encoder, &dev->mode_config.encoder_list, head) {
+		radeon_encoder = to_radeon_encoder(encoder);
+		if (encoder->crtc != crtc)
+			continue;
+		if (first) {
+			radeon_crtc->rmx_type = radeon_encoder->rmx_type;
+			radeon_crtc->devices = radeon_encoder->devices;
+			memcpy(&radeon_crtc->native_mode,
+				&radeon_encoder->native_mode,
+				sizeof(struct radeon_native_mode));
+			first = false;
+		} else {
+			if (radeon_crtc->rmx_type != radeon_encoder->rmx_type) {
+				/* WARNING: Right now this can't happen but
+				 * in the future we need to check that scaling
+				 * are consistent accross different encoder
+				 * (ie all encoder can work with the same
+				 *  scaling).
+				 */
+				DRM_ERROR("Scaling not consistent accross encoder.\n");
+				return false;
+			}
 		}
 	}
-
-	if (ASIC_IS_AVIVO(rdev)) {
-		radeon_init_disp_bw_avivo(dev,
-					  modes[0],
-					  pixel_bytes[0],
-					  modes[1],
-					  pixel_bytes[1]);
+	if (radeon_crtc->rmx_type != RMX_OFF) {
+		fixed20_12 a, b;
+		a.full = rfixed_const(crtc->mode.vdisplay);
+		b.full = rfixed_const(radeon_crtc->native_mode.panel_xres);
+		radeon_crtc->vsc.full = rfixed_div(a, b);
+		a.full = rfixed_const(crtc->mode.hdisplay);
+		b.full = rfixed_const(radeon_crtc->native_mode.panel_yres);
+		radeon_crtc->hsc.full = rfixed_div(a, b);
 	} else {
-		radeon_init_disp_bw_legacy(dev,
-					   modes[0],
-					   pixel_bytes[0],
-					   modes[1],
-					   pixel_bytes[1]);
+		radeon_crtc->vsc.full = rfixed_const(1);
+		radeon_crtc->hsc.full = rfixed_const(1);
 	}
+	return true;
 }
diff --git a/drivers/gpu/drm/radeon/radeon_encoders.c b/drivers/gpu/drm/radeon/radeon_encoders.c
index ea15284e758..0a92706eac1 100644
--- a/drivers/gpu/drm/radeon/radeon_encoders.c
+++ b/drivers/gpu/drm/radeon/radeon_encoders.c
@@ -154,7 +154,6 @@ void radeon_rmx_mode_fixup(struct drm_encoder *encoder,
 
 	if (mode->hdisplay < native_mode->panel_xres ||
 	    mode->vdisplay < native_mode->panel_yres) {
-		radeon_encoder->flags |= RADEON_USE_RMX;
 		if (ASIC_IS_AVIVO(rdev)) {
 			adjusted_mode->hdisplay = native_mode->panel_xres;
 			adjusted_mode->vdisplay = native_mode->panel_yres;
@@ -197,15 +196,13 @@ void radeon_rmx_mode_fixup(struct drm_encoder *encoder,
 	}
 }
 
+
 static bool radeon_atom_mode_fixup(struct drm_encoder *encoder,
 				   struct drm_display_mode *mode,
 				   struct drm_display_mode *adjusted_mode)
 {
-
 	struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder);
 
-	radeon_encoder->flags &= ~RADEON_USE_RMX;
-
 	drm_mode_set_crtcinfo(adjusted_mode, 0);
 
 	if (radeon_encoder->rmx_type != RMX_OFF)
@@ -808,234 +805,6 @@ atombios_dig_transmitter_setup(struct drm_encoder *encoder, int action)
 
 }
 
-static void atom_rv515_force_tv_scaler(struct radeon_device *rdev)
-{
-
-	WREG32(0x659C, 0x0);
-	WREG32(0x6594, 0x705);
-	WREG32(0x65A4, 0x10001);
-	WREG32(0x65D8, 0x0);
-	WREG32(0x65B0, 0x0);
-	WREG32(0x65C0, 0x0);
-	WREG32(0x65D4, 0x0);
-	WREG32(0x6578, 0x0);
-	WREG32(0x657C, 0x841880A8);
-	WREG32(0x6578, 0x1);
-	WREG32(0x657C, 0x84208680);
-	WREG32(0x6578, 0x2);
-	WREG32(0x657C, 0xBFF880B0);
-	WREG32(0x6578, 0x100);
-	WREG32(0x657C, 0x83D88088);
-	WREG32(0x6578, 0x101);
-	WREG32(0x657C, 0x84608680);
-	WREG32(0x6578, 0x102);
-	WREG32(0x657C, 0xBFF080D0);
-	WREG32(0x6578, 0x200);
-	WREG32(0x657C, 0x83988068);
-	WREG32(0x6578, 0x201);
-	WREG32(0x657C, 0x84A08680);
-	WREG32(0x6578, 0x202);
-	WREG32(0x657C, 0xBFF080F8);
-	WREG32(0x6578, 0x300);
-	WREG32(0x657C, 0x83588058);
-	WREG32(0x6578, 0x301);
-	WREG32(0x657C, 0x84E08660);
-	WREG32(0x6578, 0x302);
-	WREG32(0x657C, 0xBFF88120);
-	WREG32(0x6578, 0x400);
-	WREG32(0x657C, 0x83188040);
-	WREG32(0x6578, 0x401);
-	WREG32(0x657C, 0x85008660);
-	WREG32(0x6578, 0x402);
-	WREG32(0x657C, 0xBFF88150);
-	WREG32(0x6578, 0x500);
-	WREG32(0x657C, 0x82D88030);
-	WREG32(0x6578, 0x501);
-	WREG32(0x657C, 0x85408640);
-	WREG32(0x6578, 0x502);
-	WREG32(0x657C, 0xBFF88180);
-	WREG32(0x6578, 0x600);
-	WREG32(0x657C, 0x82A08018);
-	WREG32(0x6578, 0x601);
-	WREG32(0x657C, 0x85808620);
-	WREG32(0x6578, 0x602);
-	WREG32(0x657C, 0xBFF081B8);
-	WREG32(0x6578, 0x700);
-	WREG32(0x657C, 0x82608010);
-	WREG32(0x6578, 0x701);
-	WREG32(0x657C, 0x85A08600);
-	WREG32(0x6578, 0x702);
-	WREG32(0x657C, 0x800081F0);
-	WREG32(0x6578, 0x800);
-	WREG32(0x657C, 0x8228BFF8);
-	WREG32(0x6578, 0x801);
-	WREG32(0x657C, 0x85E085E0);
-	WREG32(0x6578, 0x802);
-	WREG32(0x657C, 0xBFF88228);
-	WREG32(0x6578, 0x10000);
-	WREG32(0x657C, 0x82A8BF00);
-	WREG32(0x6578, 0x10001);
-	WREG32(0x657C, 0x82A08CC0);
-	WREG32(0x6578, 0x10002);
-	WREG32(0x657C, 0x8008BEF8);
-	WREG32(0x6578, 0x10100);
-	WREG32(0x657C, 0x81F0BF28);
-	WREG32(0x6578, 0x10101);
-	WREG32(0x657C, 0x83608CA0);
-	WREG32(0x6578, 0x10102);
-	WREG32(0x657C, 0x8018BED0);
-	WREG32(0x6578, 0x10200);
-	WREG32(0x657C, 0x8148BF38);
-	WREG32(0x6578, 0x10201);
-	WREG32(0x657C, 0x84408C80);
-	WREG32(0x6578, 0x10202);
-	WREG32(0x657C, 0x8008BEB8);
-	WREG32(0x6578, 0x10300);
-	WREG32(0x657C, 0x80B0BF78);
-	WREG32(0x6578, 0x10301);
-	WREG32(0x657C, 0x85008C20);
-	WREG32(0x6578, 0x10302);
-	WREG32(0x657C, 0x8020BEA0);
-	WREG32(0x6578, 0x10400);
-	WREG32(0x657C, 0x8028BF90);
-	WREG32(0x6578, 0x10401);
-	WREG32(0x657C, 0x85E08BC0);
-	WREG32(0x6578, 0x10402);
-	WREG32(0x657C, 0x8018BE90);
-	WREG32(0x6578, 0x10500);
-	WREG32(0x657C, 0xBFB8BFB0);
-	WREG32(0x6578, 0x10501);
-	WREG32(0x657C, 0x86C08B40);
-	WREG32(0x6578, 0x10502);
-	WREG32(0x657C, 0x8010BE90);
-	WREG32(0x6578, 0x10600);
-	WREG32(0x657C, 0xBF58BFC8);
-	WREG32(0x6578, 0x10601);
-	WREG32(0x657C, 0x87A08AA0);
-	WREG32(0x6578, 0x10602);
-	WREG32(0x657C, 0x8010BE98);
-	WREG32(0x6578, 0x10700);
-	WREG32(0x657C, 0xBF10BFF0);
-	WREG32(0x6578, 0x10701);
-	WREG32(0x657C, 0x886089E0);
-	WREG32(0x6578, 0x10702);
-	WREG32(0x657C, 0x8018BEB0);
-	WREG32(0x6578, 0x10800);
-	WREG32(0x657C, 0xBED8BFE8);
-	WREG32(0x6578, 0x10801);
-	WREG32(0x657C, 0x89408940);
-	WREG32(0x6578, 0x10802);
-	WREG32(0x657C, 0xBFE8BED8);
-	WREG32(0x6578, 0x20000);
-	WREG32(0x657C, 0x80008000);
-	WREG32(0x6578, 0x20001);
-	WREG32(0x657C, 0x90008000);
-	WREG32(0x6578, 0x20002);
-	WREG32(0x657C, 0x80008000);
-	WREG32(0x6578, 0x20003);
-	WREG32(0x657C, 0x80008000);
-	WREG32(0x6578, 0x20100);
-	WREG32(0x657C, 0x80108000);
-	WREG32(0x6578, 0x20101);
-	WREG32(0x657C, 0x8FE0BF70);
-	WREG32(0x6578, 0x20102);
-	WREG32(0x657C, 0xBFE880C0);
-	WREG32(0x6578, 0x20103);
-	WREG32(0x657C, 0x80008000);
-	WREG32(0x6578, 0x20200);
-	WREG32(0x657C, 0x8018BFF8);
-	WREG32(0x6578, 0x20201);
-	WREG32(0x657C, 0x8F80BF08);
-	WREG32(0x6578, 0x20202);
-	WREG32(0x657C, 0xBFD081A0);
-	WREG32(0x6578, 0x20203);
-	WREG32(0x657C, 0xBFF88000);
-	WREG32(0x6578, 0x20300);
-	WREG32(0x657C, 0x80188000);
-	WREG32(0x6578, 0x20301);
-	WREG32(0x657C, 0x8EE0BEC0);
-	WREG32(0x6578, 0x20302);
-	WREG32(0x657C, 0xBFB082A0);
-	WREG32(0x6578, 0x20303);
-	WREG32(0x657C, 0x80008000);
-	WREG32(0x6578, 0x20400);
-	WREG32(0x657C, 0x80188000);
-	WREG32(0x6578, 0x20401);
-	WREG32(0x657C, 0x8E00BEA0);
-	WREG32(0x6578, 0x20402);
-	WREG32(0x657C, 0xBF8883C0);
-	WREG32(0x6578, 0x20403);
-	WREG32(0x657C, 0x80008000);
-	WREG32(0x6578, 0x20500);
-	WREG32(0x657C, 0x80188000);
-	WREG32(0x6578, 0x20501);
-	WREG32(0x657C, 0x8D00BE90);
-	WREG32(0x6578, 0x20502);
-	WREG32(0x657C, 0xBF588500);
-	WREG32(0x6578, 0x20503);
-	WREG32(0x657C, 0x80008008);
-	WREG32(0x6578, 0x20600);
-	WREG32(0x657C, 0x80188000);
-	WREG32(0x6578, 0x20601);
-	WREG32(0x657C, 0x8BC0BE98);
-	WREG32(0x6578, 0x20602);
-	WREG32(0x657C, 0xBF308660);
-	WREG32(0x6578, 0x20603);
-	WREG32(0x657C, 0x80008008);
-	WREG32(0x6578, 0x20700);
-	WREG32(0x657C, 0x80108000);
-	WREG32(0x6578, 0x20701);
-	WREG32(0x657C, 0x8A80BEB0);
-	WREG32(0x6578, 0x20702);
-	WREG32(0x657C, 0xBF0087C0);
-	WREG32(0x6578, 0x20703);
-	WREG32(0x657C, 0x80008008);
-	WREG32(0x6578, 0x20800);
-	WREG32(0x657C, 0x80108000);
-	WREG32(0x6578, 0x20801);
-	WREG32(0x657C, 0x8920BED0);
-	WREG32(0x6578, 0x20802);
-	WREG32(0x657C, 0xBED08920);
-	WREG32(0x6578, 0x20803);
-	WREG32(0x657C, 0x80008010);
-	WREG32(0x6578, 0x30000);
-	WREG32(0x657C, 0x90008000);
-	WREG32(0x6578, 0x30001);
-	WREG32(0x657C, 0x80008000);
-	WREG32(0x6578, 0x30100);
-	WREG32(0x657C, 0x8FE0BF90);
-	WREG32(0x6578, 0x30101);
-	WREG32(0x657C, 0xBFF880A0);
-	WREG32(0x6578, 0x30200);
-	WREG32(0x657C, 0x8F60BF40);
-	WREG32(0x6578, 0x30201);
-	WREG32(0x657C, 0xBFE88180);
-	WREG32(0x6578, 0x30300);
-	WREG32(0x657C, 0x8EC0BF00);
-	WREG32(0x6578, 0x30301);
-	WREG32(0x657C, 0xBFC88280);
-	WREG32(0x6578, 0x30400);
-	WREG32(0x657C, 0x8DE0BEE0);
-	WREG32(0x6578, 0x30401);
-	WREG32(0x657C, 0xBFA083A0);
-	WREG32(0x6578, 0x30500);
-	WREG32(0x657C, 0x8CE0BED0);
-	WREG32(0x6578, 0x30501);
-	WREG32(0x657C, 0xBF7884E0);
-	WREG32(0x6578, 0x30600);
-	WREG32(0x657C, 0x8BA0BED8);
-	WREG32(0x6578, 0x30601);
-	WREG32(0x657C, 0xBF508640);
-	WREG32(0x6578, 0x30700);
-	WREG32(0x657C, 0x8A60BEE8);
-	WREG32(0x6578, 0x30701);
-	WREG32(0x657C, 0xBF2087A0);
-	WREG32(0x6578, 0x30800);
-	WREG32(0x657C, 0x8900BF00);
-	WREG32(0x6578, 0x30801);
-	WREG32(0x657C, 0xBF008900);
-}
-
 static void
 atombios_yuv_setup(struct drm_encoder *encoder, bool enable)
 {
@@ -1073,129 +842,6 @@ atombios_yuv_setup(struct drm_encoder *encoder, bool enable)
 	WREG32(reg, temp);
 }
 
-static void
-atombios_overscan_setup(struct drm_encoder *encoder,
-			struct drm_display_mode *mode,
-			struct drm_display_mode *adjusted_mode)
-{
-	struct drm_device *dev = encoder->dev;
-	struct radeon_device *rdev = dev->dev_private;
-	struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder);
-	struct radeon_crtc *radeon_crtc = to_radeon_crtc(encoder->crtc);
-	SET_CRTC_OVERSCAN_PS_ALLOCATION args;
-	int index = GetIndexIntoMasterTable(COMMAND, SetCRTC_OverScan);
-
-	memset(&args, 0, sizeof(args));
-
-	args.usOverscanRight = 0;
-	args.usOverscanLeft = 0;
-	args.usOverscanBottom = 0;
-	args.usOverscanTop = 0;
-	args.ucCRTC = radeon_crtc->crtc_id;
-
-	if (radeon_encoder->flags & RADEON_USE_RMX) {
-		if (radeon_encoder->rmx_type == RMX_FULL) {
-			args.usOverscanRight = 0;
-			args.usOverscanLeft = 0;
-			args.usOverscanBottom = 0;
-			args.usOverscanTop = 0;
-		} else if (radeon_encoder->rmx_type == RMX_CENTER) {
-			args.usOverscanTop = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2;
-			args.usOverscanBottom = (adjusted_mode->crtc_vdisplay - mode->crtc_vdisplay) / 2;
-			args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2;
-			args.usOverscanRight = (adjusted_mode->crtc_hdisplay - mode->crtc_hdisplay) / 2;
-		} else if (radeon_encoder->rmx_type == RMX_ASPECT) {
-			int a1 = mode->crtc_vdisplay * adjusted_mode->crtc_hdisplay;
-			int a2 = adjusted_mode->crtc_vdisplay * mode->crtc_hdisplay;
-
-			if (a1 > a2) {
-				args.usOverscanLeft = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2;
-				args.usOverscanRight = (adjusted_mode->crtc_hdisplay - (a2 / mode->crtc_vdisplay)) / 2;
-			} else if (a2 > a1) {
-				args.usOverscanLeft = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2;
-				args.usOverscanRight = (adjusted_mode->crtc_vdisplay - (a1 / mode->crtc_hdisplay)) / 2;
-			}
-		}
-	}
-
-	atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args);
-
-}
-
-static void
-atombios_scaler_setup(struct drm_encoder *encoder)
-{
-	struct drm_device *dev = encoder->dev;
-	struct radeon_device *rdev = dev->dev_private;
-	struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder);
-	struct radeon_crtc *radeon_crtc = to_radeon_crtc(encoder->crtc);
-	ENABLE_SCALER_PS_ALLOCATION args;
-	int index = GetIndexIntoMasterTable(COMMAND, EnableScaler);
-	/* fixme - fill in enc_priv for atom dac */
-	enum radeon_tv_std tv_std = TV_STD_NTSC;
-
-	if (!ASIC_IS_AVIVO(rdev) && radeon_crtc->crtc_id)
-		return;
-
-	memset(&args, 0, sizeof(args));
-
-	args.ucScaler = radeon_crtc->crtc_id;
-
-	if (radeon_encoder->devices & (ATOM_DEVICE_TV_SUPPORT)) {
-		switch (tv_std) {
-		case TV_STD_NTSC:
-		default:
-			args.ucTVStandard = ATOM_TV_NTSC;
-			break;
-		case TV_STD_PAL:
-			args.ucTVStandard = ATOM_TV_PAL;
-			break;
-		case TV_STD_PAL_M:
-			args.ucTVStandard = ATOM_TV_PALM;
-			break;
-		case TV_STD_PAL_60:
-			args.ucTVStandard = ATOM_TV_PAL60;
-			break;
-		case TV_STD_NTSC_J:
-			args.ucTVStandard = ATOM_TV_NTSCJ;
-			break;
-		case TV_STD_SCART_PAL:
-			args.ucTVStandard = ATOM_TV_PAL; /* ??? */
-			break;
-		case TV_STD_SECAM:
-			args.ucTVStandard = ATOM_TV_SECAM;
-			break;
-		case TV_STD_PAL_CN:
-			args.ucTVStandard = ATOM_TV_PALCN;
-			break;
-		}
-		args.ucEnable = SCALER_ENABLE_MULTITAP_MODE;
-	} else if (radeon_encoder->devices & (ATOM_DEVICE_CV_SUPPORT)) {
-		args.ucTVStandard = ATOM_TV_CV;
-		args.ucEnable = SCALER_ENABLE_MULTITAP_MODE;
-	} else if (radeon_encoder->flags & RADEON_USE_RMX) {
-		if (radeon_encoder->rmx_type == RMX_FULL)
-			args.ucEnable = ATOM_SCALER_EXPANSION;
-		else if (radeon_encoder->rmx_type == RMX_CENTER)
-			args.ucEnable = ATOM_SCALER_CENTER;
-		else if (radeon_encoder->rmx_type == RMX_ASPECT)
-			args.ucEnable = ATOM_SCALER_EXPANSION;
-	} else {
-		if (ASIC_IS_AVIVO(rdev))
-			args.ucEnable = ATOM_SCALER_DISABLE;
-		else
-			args.ucEnable = ATOM_SCALER_CENTER;
-	}
-
-	atom_execute_table(rdev->mode_info.atom_context, index, (uint32_t *)&args);
-
-	if (radeon_encoder->devices & (ATOM_DEVICE_CV_SUPPORT | ATOM_DEVICE_TV_SUPPORT)
-	    && rdev->family >= CHIP_RV515 && rdev->family <= CHIP_RV570) {
-		atom_rv515_force_tv_scaler(rdev);
-	}
-
-}
-
 static void
 radeon_atom_encoder_dpms(struct drm_encoder *encoder, int mode)
 {
@@ -1448,8 +1094,6 @@ radeon_atom_encoder_mode_set(struct drm_encoder *encoder,
 	radeon_encoder->pixel_clock = adjusted_mode->clock;
 
 	radeon_atombios_encoder_crtc_scratch_regs(encoder, radeon_crtc->crtc_id);
-	atombios_overscan_setup(encoder, mode, adjusted_mode);
-	atombios_scaler_setup(encoder);
 	atombios_set_encoder_crtc_source(encoder);
 
 	if (ASIC_IS_AVIVO(rdev)) {
@@ -1667,6 +1311,7 @@ radeon_add_atom_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t su
 
 	radeon_encoder->encoder_id = encoder_id;
 	radeon_encoder->devices = supported_device;
+	radeon_encoder->rmx_type = RMX_OFF;
 
 	switch (radeon_encoder->encoder_id) {
 	case ENCODER_OBJECT_ID_INTERNAL_LVDS:
@@ -1700,14 +1345,8 @@ radeon_add_atom_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t su
 	case ENCODER_OBJECT_ID_INTERNAL_KLDSCP_LVTMA:
 	case ENCODER_OBJECT_ID_INTERNAL_UNIPHY1:
 	case ENCODER_OBJECT_ID_INTERNAL_UNIPHY2:
-		if (radeon_encoder->devices & (ATOM_DEVICE_LCD_SUPPORT)) {
-			radeon_encoder->rmx_type = RMX_FULL;
-			drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_LVDS);
-			radeon_encoder->enc_priv = radeon_atombios_get_lvds_info(radeon_encoder);
-		} else {
-			drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS);
-			radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder);
-		}
+		drm_encoder_init(dev, encoder, &radeon_atom_enc_funcs, DRM_MODE_ENCODER_TMDS);
+		radeon_encoder->enc_priv = radeon_atombios_set_dig_info(radeon_encoder);
 		drm_encoder_helper_add(encoder, &radeon_atom_dig_helper_funcs);
 		break;
 	}
diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
index 0613790e2a5..7d06dc98a42 100644
--- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
+++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
@@ -29,6 +29,171 @@
 #include "radeon_fixed.h"
 #include "radeon.h"
 
+static void radeon_legacy_rmx_mode_set(struct drm_crtc *crtc,
+				       struct drm_display_mode *mode,
+				       struct drm_display_mode *adjusted_mode)
+{
+	struct drm_device *dev = crtc->dev;
+	struct radeon_device *rdev = dev->dev_private;
+	struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc);
+	int xres = mode->hdisplay;
+	int yres = mode->vdisplay;
+	bool hscale = true, vscale = true;
+	int hsync_wid;
+	int vsync_wid;
+	int hsync_start;
+	int blank_width;
+	u32 scale, inc, crtc_more_cntl;
+	u32 fp_horz_stretch, fp_vert_stretch, fp_horz_vert_active;
+	u32 fp_h_sync_strt_wid, fp_crtc_h_total_disp;
+	u32 fp_v_sync_strt_wid, fp_crtc_v_total_disp;
+	struct radeon_native_mode *native_mode = &radeon_crtc->native_mode;
+
+	fp_vert_stretch = RREG32(RADEON_FP_VERT_STRETCH) &
+		(RADEON_VERT_STRETCH_RESERVED |
+		 RADEON_VERT_AUTO_RATIO_INC);
+	fp_horz_stretch = RREG32(RADEON_FP_HORZ_STRETCH) &
+		(RADEON_HORZ_FP_LOOP_STRETCH |
+		 RADEON_HORZ_AUTO_RATIO_INC);
+
+	crtc_more_cntl = 0;
+	if ((rdev->family == CHIP_RS100) ||
+	    (rdev->family == CHIP_RS200)) {
+		/* This is to workaround the asic bug for RMX, some versions
+		   of BIOS dosen't have this register initialized correctly. */
+		crtc_more_cntl |= RADEON_CRTC_H_CUTOFF_ACTIVE_EN;
+	}
+
+
+	fp_crtc_h_total_disp = ((((mode->crtc_htotal / 8) - 1) & 0x3ff)
+				| ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16));
+
+	hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8;
+	if (!hsync_wid)
+		hsync_wid = 1;
+	hsync_start = mode->crtc_hsync_start - 8;
+
+	fp_h_sync_strt_wid = ((hsync_start & 0x1fff)
+			      | ((hsync_wid & 0x3f) << 16)
+			      | ((mode->flags & DRM_MODE_FLAG_NHSYNC)
+				 ? RADEON_CRTC_H_SYNC_POL
+				 : 0));
+
+	fp_crtc_v_total_disp = (((mode->crtc_vtotal - 1) & 0xffff)
+				| ((mode->crtc_vdisplay - 1) << 16));
+
+	vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start;
+	if (!vsync_wid)
+		vsync_wid = 1;
+
+	fp_v_sync_strt_wid = (((mode->crtc_vsync_start - 1) & 0xfff)
+			      | ((vsync_wid & 0x1f) << 16)
+			      | ((mode->flags & DRM_MODE_FLAG_NVSYNC)
+				 ? RADEON_CRTC_V_SYNC_POL
+				 : 0));
+
+	fp_horz_vert_active = 0;
+
+	if (native_mode->panel_xres == 0 ||
+	    native_mode->panel_yres == 0) {
+		hscale = false;
+		vscale = false;
+	} else {
+		if (xres > native_mode->panel_xres)
+			xres = native_mode->panel_xres;
+		if (yres > native_mode->panel_yres)
+			yres = native_mode->panel_yres;
+
+		if (xres == native_mode->panel_xres)
+			hscale = false;
+		if (yres == native_mode->panel_yres)
+			vscale = false;
+	}
+
+	switch (radeon_crtc->rmx_type) {
+	case RMX_FULL:
+	case RMX_ASPECT:
+		if (!hscale)
+			fp_horz_stretch |= ((xres/8-1) << 16);
+		else {
+			inc = (fp_horz_stretch & RADEON_HORZ_AUTO_RATIO_INC) ? 1 : 0;
+			scale = ((xres + inc) * RADEON_HORZ_STRETCH_RATIO_MAX)
+				/ native_mode->panel_xres + 1;
+			fp_horz_stretch |= (((scale) & RADEON_HORZ_STRETCH_RATIO_MASK) |
+					RADEON_HORZ_STRETCH_BLEND |
+					RADEON_HORZ_STRETCH_ENABLE |
+					((native_mode->panel_xres/8-1) << 16));
+		}
+
+		if (!vscale)
+			fp_vert_stretch |= ((yres-1) << 12);
+		else {
+			inc = (fp_vert_stretch & RADEON_VERT_AUTO_RATIO_INC) ? 1 : 0;
+			scale = ((yres + inc) * RADEON_VERT_STRETCH_RATIO_MAX)
+				/ native_mode->panel_yres + 1;
+			fp_vert_stretch |= (((scale) & RADEON_VERT_STRETCH_RATIO_MASK) |
+					RADEON_VERT_STRETCH_ENABLE |
+					RADEON_VERT_STRETCH_BLEND |
+					((native_mode->panel_yres-1) << 12));
+		}
+		break;
+	case RMX_CENTER:
+		fp_horz_stretch |= ((xres/8-1) << 16);
+		fp_vert_stretch |= ((yres-1) << 12);
+
+		crtc_more_cntl |= (RADEON_CRTC_AUTO_HORZ_CENTER_EN |
+				RADEON_CRTC_AUTO_VERT_CENTER_EN);
+
+		blank_width = (mode->crtc_hblank_end - mode->crtc_hblank_start) / 8;
+		if (blank_width > 110)
+			blank_width = 110;
+
+		fp_crtc_h_total_disp = (((blank_width) & 0x3ff)
+				| ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16));
+
+		hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8;
+		if (!hsync_wid)
+			hsync_wid = 1;
+
+		fp_h_sync_strt_wid = ((((mode->crtc_hsync_start - mode->crtc_hblank_start) / 8) & 0x1fff)
+				| ((hsync_wid & 0x3f) << 16)
+				| ((mode->flags & DRM_MODE_FLAG_NHSYNC)
+					? RADEON_CRTC_H_SYNC_POL
+					: 0));
+
+		fp_crtc_v_total_disp = (((mode->crtc_vblank_end - mode->crtc_vblank_start) & 0xffff)
+				| ((mode->crtc_vdisplay - 1) << 16));
+
+		vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start;
+		if (!vsync_wid)
+			vsync_wid = 1;
+
+		fp_v_sync_strt_wid = ((((mode->crtc_vsync_start - mode->crtc_vblank_start) & 0xfff)
+					| ((vsync_wid & 0x1f) << 16)
+					| ((mode->flags & DRM_MODE_FLAG_NVSYNC)
+						? RADEON_CRTC_V_SYNC_POL
+						: 0)));
+
+		fp_horz_vert_active = (((native_mode->panel_yres) & 0xfff) |
+				(((native_mode->panel_xres / 8) & 0x1ff) << 16));
+		break;
+	case RMX_OFF:
+	default:
+		fp_horz_stretch |= ((xres/8-1) << 16);
+		fp_vert_stretch |= ((yres-1) << 12);
+		break;
+	}
+
+	WREG32(RADEON_FP_HORZ_STRETCH,      fp_horz_stretch);
+	WREG32(RADEON_FP_VERT_STRETCH,      fp_vert_stretch);
+	WREG32(RADEON_CRTC_MORE_CNTL,       crtc_more_cntl);
+	WREG32(RADEON_FP_HORZ_VERT_ACTIVE,  fp_horz_vert_active);
+	WREG32(RADEON_FP_H_SYNC_STRT_WID,   fp_h_sync_strt_wid);
+	WREG32(RADEON_FP_V_SYNC_STRT_WID,   fp_v_sync_strt_wid);
+	WREG32(RADEON_FP_CRTC_H_TOTAL_DISP, fp_crtc_h_total_disp);
+	WREG32(RADEON_FP_CRTC_V_TOTAL_DISP, fp_crtc_v_total_disp);
+}
+
 void radeon_restore_common_regs(struct drm_device *dev)
 {
 	/* don't need this yet */
@@ -757,6 +922,8 @@ static bool radeon_crtc_mode_fixup(struct drm_crtc *crtc,
 				   struct drm_display_mode *mode,
 				   struct drm_display_mode *adjusted_mode)
 {
+	if (!radeon_crtc_scaling_mode_fixup(crtc, mode, adjusted_mode))
+		return false;
 	return true;
 }
 
@@ -765,16 +932,25 @@ static int radeon_crtc_mode_set(struct drm_crtc *crtc,
 				 struct drm_display_mode *adjusted_mode,
 				 int x, int y, struct drm_framebuffer *old_fb)
 {
-
-	DRM_DEBUG("\n");
+	struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc);
+	struct drm_device *dev = crtc->dev;
+	struct radeon_device *rdev = dev->dev_private;
 
 	/* TODO TV */
-
 	radeon_crtc_set_base(crtc, x, y, old_fb);
 	radeon_set_crtc_timing(crtc, adjusted_mode);
 	radeon_set_pll(crtc, adjusted_mode);
-	radeon_init_disp_bandwidth(crtc->dev);
-
+	radeon_bandwidth_update(rdev);
+	if (radeon_crtc->crtc_id == 0) {
+		radeon_legacy_rmx_mode_set(crtc, mode, adjusted_mode);
+	} else {
+		if (radeon_crtc->rmx_type != RMX_OFF) {
+			/* FIXME: only first crtc has rmx what should we
+			 * do ?
+			 */
+			DRM_ERROR("Mode need scaling but only first crtc can do that.\n");
+		}
+	}
 	return 0;
 }
 
@@ -805,478 +981,3 @@ void radeon_legacy_init_crtc(struct drm_device *dev,
 		radeon_crtc->crtc_offset = RADEON_CRTC2_H_TOTAL_DISP - RADEON_CRTC_H_TOTAL_DISP;
 	drm_crtc_helper_add(&radeon_crtc->base, &legacy_helper_funcs);
 }
-
-void radeon_init_disp_bw_legacy(struct drm_device *dev,
-				struct drm_display_mode *mode1,
-				uint32_t pixel_bytes1,
-				struct drm_display_mode *mode2,
-				uint32_t pixel_bytes2)
-{
-	struct radeon_device *rdev = dev->dev_private;
-	fixed20_12 trcd_ff, trp_ff, tras_ff, trbs_ff, tcas_ff;
-	fixed20_12 sclk_ff, mclk_ff, sclk_eff_ff, sclk_delay_ff;
-	fixed20_12 peak_disp_bw, mem_bw, pix_clk, pix_clk2, temp_ff, crit_point_ff;
-	uint32_t temp, data, mem_trcd, mem_trp, mem_tras;
-	fixed20_12 memtcas_ff[8] = {
-		fixed_init(1),
-		fixed_init(2),
-		fixed_init(3),
-		fixed_init(0),
-		fixed_init_half(1),
-		fixed_init_half(2),
-		fixed_init(0),
-	};
-	fixed20_12 memtcas_rs480_ff[8] = {
-		fixed_init(0),
-		fixed_init(1),
-		fixed_init(2),
-		fixed_init(3),
-		fixed_init(0),
-		fixed_init_half(1),
-		fixed_init_half(2),
-		fixed_init_half(3),
-	};
-	fixed20_12 memtcas2_ff[8] = {
-		fixed_init(0),
-		fixed_init(1),
-		fixed_init(2),
-		fixed_init(3),
-		fixed_init(4),
-		fixed_init(5),
-		fixed_init(6),
-		fixed_init(7),
-	};
-	fixed20_12 memtrbs[8] = {
-		fixed_init(1),
-		fixed_init_half(1),
-		fixed_init(2),
-		fixed_init_half(2),
-		fixed_init(3),
-		fixed_init_half(3),
-		fixed_init(4),
-		fixed_init_half(4)
-	};
-	fixed20_12 memtrbs_r4xx[8] = {
-		fixed_init(4),
-		fixed_init(5),
-		fixed_init(6),
-		fixed_init(7),
-		fixed_init(8),
-		fixed_init(9),
-		fixed_init(10),
-		fixed_init(11)
-	};
-	fixed20_12 min_mem_eff;
-	fixed20_12 mc_latency_sclk, mc_latency_mclk, k1;
-	fixed20_12 cur_latency_mclk, cur_latency_sclk;
-	fixed20_12 disp_latency, disp_latency_overhead, disp_drain_rate,
-		disp_drain_rate2, read_return_rate;
-	fixed20_12 time_disp1_drop_priority;
-	int c;
-	int cur_size = 16;       /* in octawords */
-	int critical_point = 0, critical_point2;
-/* 	uint32_t read_return_rate, time_disp1_drop_priority; */
-	int stop_req, max_stop_req;
-
-	min_mem_eff.full = rfixed_const_8(0);
-	/* get modes */
-	if ((rdev->disp_priority == 2) && ASIC_IS_R300(rdev)) {
-		uint32_t mc_init_misc_lat_timer = RREG32(R300_MC_INIT_MISC_LAT_TIMER);
-		mc_init_misc_lat_timer &= ~(R300_MC_DISP1R_INIT_LAT_MASK << R300_MC_DISP1R_INIT_LAT_SHIFT);
-		mc_init_misc_lat_timer &= ~(R300_MC_DISP0R_INIT_LAT_MASK << R300_MC_DISP0R_INIT_LAT_SHIFT);
-		/* check crtc enables */
-		if (mode2)
-			mc_init_misc_lat_timer |= (1 << R300_MC_DISP1R_INIT_LAT_SHIFT);
-		if (mode1)
-			mc_init_misc_lat_timer |= (1 << R300_MC_DISP0R_INIT_LAT_SHIFT);
-		WREG32(R300_MC_INIT_MISC_LAT_TIMER, mc_init_misc_lat_timer);
-	}
-
-	/*
-	 * determine is there is enough bw for current mode
-	 */
-	mclk_ff.full = rfixed_const(rdev->clock.default_mclk);
-	temp_ff.full = rfixed_const(100);
-	mclk_ff.full = rfixed_div(mclk_ff, temp_ff);
-	sclk_ff.full = rfixed_const(rdev->clock.default_sclk);
-	sclk_ff.full = rfixed_div(sclk_ff, temp_ff);
-
-	temp = (rdev->mc.vram_width / 8) * (rdev->mc.vram_is_ddr ? 2 : 1);
-	temp_ff.full = rfixed_const(temp);
-	mem_bw.full = rfixed_mul(mclk_ff, temp_ff);
-
-	pix_clk.full = 0;
-	pix_clk2.full = 0;
-	peak_disp_bw.full = 0;
-	if (mode1) {
-		temp_ff.full = rfixed_const(1000);
-		pix_clk.full = rfixed_const(mode1->clock); /* convert to fixed point */
-		pix_clk.full = rfixed_div(pix_clk, temp_ff);
-		temp_ff.full = rfixed_const(pixel_bytes1);
-		peak_disp_bw.full += rfixed_mul(pix_clk, temp_ff);
-	}
-	if (mode2) {
-		temp_ff.full = rfixed_const(1000);
-		pix_clk2.full = rfixed_const(mode2->clock); /* convert to fixed point */
-		pix_clk2.full = rfixed_div(pix_clk2, temp_ff);
-		temp_ff.full = rfixed_const(pixel_bytes2);
-		peak_disp_bw.full += rfixed_mul(pix_clk2, temp_ff);
-	}
-
-	mem_bw.full = rfixed_mul(mem_bw, min_mem_eff);
-	if (peak_disp_bw.full >= mem_bw.full) {
-		DRM_ERROR("You may not have enough display bandwidth for current mode\n"
-			  "If you have flickering problem, try to lower resolution, refresh rate, or color depth\n");
-	}
-
-	/*  Get values from the EXT_MEM_CNTL register...converting its contents. */
-	temp = RREG32(RADEON_MEM_TIMING_CNTL);
-	if ((rdev->family == CHIP_RV100) || (rdev->flags & RADEON_IS_IGP)) { /* RV100, M6, IGPs */
-		mem_trcd = ((temp >> 2) & 0x3) + 1;
-		mem_trp  = ((temp & 0x3)) + 1;
-		mem_tras = ((temp & 0x70) >> 4) + 1;
-	} else if (rdev->family == CHIP_R300 ||
-		   rdev->family == CHIP_R350) { /* r300, r350 */
-		mem_trcd = (temp & 0x7) + 1;
-		mem_trp = ((temp >> 8) & 0x7) + 1;
-		mem_tras = ((temp >> 11) & 0xf) + 4;
-	} else if (rdev->family == CHIP_RV350 ||
-		   rdev->family <= CHIP_RV380) {
-		/* rv3x0 */
-		mem_trcd = (temp & 0x7) + 3;
-		mem_trp = ((temp >> 8) & 0x7) + 3;
-		mem_tras = ((temp >> 11) & 0xf) + 6;
-	} else if (rdev->family == CHIP_R420 ||
-		   rdev->family == CHIP_R423 ||
-		   rdev->family == CHIP_RV410) {
-		/* r4xx */
-		mem_trcd = (temp & 0xf) + 3;
-		if (mem_trcd > 15)
-			mem_trcd = 15;
-		mem_trp = ((temp >> 8) & 0xf) + 3;
-		if (mem_trp > 15)
-			mem_trp = 15;
-		mem_tras = ((temp >> 12) & 0x1f) + 6;
-		if (mem_tras > 31)
-			mem_tras = 31;
-	} else { /* RV200, R200 */
-		mem_trcd = (temp & 0x7) + 1;
-		mem_trp = ((temp >> 8) & 0x7) + 1;
-		mem_tras = ((temp >> 12) & 0xf) + 4;
-	}
-	/* convert to FF */
-	trcd_ff.full = rfixed_const(mem_trcd);
-	trp_ff.full = rfixed_const(mem_trp);
-	tras_ff.full = rfixed_const(mem_tras);
-
-	/* Get values from the MEM_SDRAM_MODE_REG register...converting its */
-	temp = RREG32(RADEON_MEM_SDRAM_MODE_REG);
-	data = (temp & (7 << 20)) >> 20;
-	if ((rdev->family == CHIP_RV100) || rdev->flags & RADEON_IS_IGP) {
-		if (rdev->family == CHIP_RS480) /* don't think rs400 */
-			tcas_ff = memtcas_rs480_ff[data];
-		else
-			tcas_ff = memtcas_ff[data];
-	} else
-		tcas_ff = memtcas2_ff[data];
-
-	if (rdev->family == CHIP_RS400 ||
-	    rdev->family == CHIP_RS480) {
-		/* extra cas latency stored in bits 23-25 0-4 clocks */
-		data = (temp >> 23) & 0x7;
-		if (data < 5)
-			tcas_ff.full += rfixed_const(data);
-	}
-
-	if (ASIC_IS_R300(rdev) && !(rdev->flags & RADEON_IS_IGP)) {
-		/* on the R300, Tcas is included in Trbs.
-		 */
-		temp = RREG32(RADEON_MEM_CNTL);
-		data = (R300_MEM_NUM_CHANNELS_MASK & temp);
-		if (data == 1) {
-			if (R300_MEM_USE_CD_CH_ONLY & temp) {
-				temp = RREG32(R300_MC_IND_INDEX);
-				temp &= ~R300_MC_IND_ADDR_MASK;
-				temp |= R300_MC_READ_CNTL_CD_mcind;
-				WREG32(R300_MC_IND_INDEX, temp);
-				temp = RREG32(R300_MC_IND_DATA);
-				data = (R300_MEM_RBS_POSITION_C_MASK & temp);
-			} else {
-				temp = RREG32(R300_MC_READ_CNTL_AB);
-				data = (R300_MEM_RBS_POSITION_A_MASK & temp);
-			}
-		} else {
-			temp = RREG32(R300_MC_READ_CNTL_AB);
-			data = (R300_MEM_RBS_POSITION_A_MASK & temp);
-		}
-		if (rdev->family == CHIP_RV410 ||
-		    rdev->family == CHIP_R420 ||
-		    rdev->family == CHIP_R423)
-			trbs_ff = memtrbs_r4xx[data];
-		else
-			trbs_ff = memtrbs[data];
-		tcas_ff.full += trbs_ff.full;
-	}
-
-	sclk_eff_ff.full = sclk_ff.full;
-
-	if (rdev->flags & RADEON_IS_AGP) {
-		fixed20_12 agpmode_ff;
-		agpmode_ff.full = rfixed_const(radeon_agpmode);
-		temp_ff.full = rfixed_const_666(16);
-		sclk_eff_ff.full -= rfixed_mul(agpmode_ff, temp_ff);
-	}
-	/* TODO PCIE lanes may affect this - agpmode == 16?? */
-
-	if (ASIC_IS_R300(rdev)) {
-		sclk_delay_ff.full = rfixed_const(250);
-	} else {
-		if ((rdev->family == CHIP_RV100) ||
-		    rdev->flags & RADEON_IS_IGP) {
-			if (rdev->mc.vram_is_ddr)
-				sclk_delay_ff.full = rfixed_const(41);
-			else
-				sclk_delay_ff.full = rfixed_const(33);
-		} else {
-			if (rdev->mc.vram_width == 128)
-				sclk_delay_ff.full = rfixed_const(57);
-			else
-				sclk_delay_ff.full = rfixed_const(41);
-		}
-	}
-
-	mc_latency_sclk.full = rfixed_div(sclk_delay_ff, sclk_eff_ff);
-
-	if (rdev->mc.vram_is_ddr) {
-		if (rdev->mc.vram_width == 32) {
-			k1.full = rfixed_const(40);
-			c  = 3;
-		} else {
-			k1.full = rfixed_const(20);
-			c  = 1;
-		}
-	} else {
-		k1.full = rfixed_const(40);
-		c  = 3;
-	}
-
-	temp_ff.full = rfixed_const(2);
-	mc_latency_mclk.full = rfixed_mul(trcd_ff, temp_ff);
-	temp_ff.full = rfixed_const(c);
-	mc_latency_mclk.full += rfixed_mul(tcas_ff, temp_ff);
-	temp_ff.full = rfixed_const(4);
-	mc_latency_mclk.full += rfixed_mul(tras_ff, temp_ff);
-	mc_latency_mclk.full += rfixed_mul(trp_ff, temp_ff);
-	mc_latency_mclk.full += k1.full;
-
-	mc_latency_mclk.full = rfixed_div(mc_latency_mclk, mclk_ff);
-	mc_latency_mclk.full += rfixed_div(temp_ff, sclk_eff_ff);
-
-	/*
-	  HW cursor time assuming worst case of full size colour cursor.
-	*/
-	temp_ff.full = rfixed_const((2 * (cur_size - (rdev->mc.vram_is_ddr + 1))));
-	temp_ff.full += trcd_ff.full;
-	if (temp_ff.full < tras_ff.full)
-		temp_ff.full = tras_ff.full;
-	cur_latency_mclk.full = rfixed_div(temp_ff, mclk_ff);
-
-	temp_ff.full = rfixed_const(cur_size);
-	cur_latency_sclk.full = rfixed_div(temp_ff, sclk_eff_ff);
-	/*
-	  Find the total latency for the display data.
-	*/
-	disp_latency_overhead.full = rfixed_const(80);
-	disp_latency_overhead.full = rfixed_div(disp_latency_overhead, sclk_ff);
-	mc_latency_mclk.full += disp_latency_overhead.full + cur_latency_mclk.full;
-	mc_latency_sclk.full += disp_latency_overhead.full + cur_latency_sclk.full;
-
-	if (mc_latency_mclk.full > mc_latency_sclk.full)
-		disp_latency.full = mc_latency_mclk.full;
-	else
-		disp_latency.full = mc_latency_sclk.full;
-
-	/* setup Max GRPH_STOP_REQ default value */
-	if (ASIC_IS_RV100(rdev))
-		max_stop_req = 0x5c;
-	else
-		max_stop_req = 0x7c;
-
-	if (mode1) {
-		/*  CRTC1
-		    Set GRPH_BUFFER_CNTL register using h/w defined optimal values.
-		    GRPH_STOP_REQ <= MIN[ 0x7C, (CRTC_H_DISP + 1) * (bit depth) / 0x10 ]
-		*/
-		stop_req = mode1->hdisplay * pixel_bytes1 / 16;
-
-		if (stop_req > max_stop_req)
-			stop_req = max_stop_req;
-
-		/*
-		  Find the drain rate of the display buffer.
-		*/
-		temp_ff.full = rfixed_const((16/pixel_bytes1));
-		disp_drain_rate.full = rfixed_div(pix_clk, temp_ff);
-
-		/*
-		  Find the critical point of the display buffer.
-		*/
-		crit_point_ff.full = rfixed_mul(disp_drain_rate, disp_latency);
-		crit_point_ff.full += rfixed_const_half(0);
-
-		critical_point = rfixed_trunc(crit_point_ff);
-
-		if (rdev->disp_priority == 2) {
-			critical_point = 0;
-		}
-
-		/*
-		  The critical point should never be above max_stop_req-4.  Setting
-		  GRPH_CRITICAL_CNTL = 0 will thus force high priority all the time.
-		*/
-		if (max_stop_req - critical_point < 4)
-			critical_point = 0;
-
-		if (critical_point == 0 && mode2 && rdev->family == CHIP_R300) {
-			/* some R300 cards have problem with this set to 0, when CRTC2 is enabled.*/
-			critical_point = 0x10;
-		}
-
-		temp = RREG32(RADEON_GRPH_BUFFER_CNTL);
-		temp &= ~(RADEON_GRPH_STOP_REQ_MASK);
-		temp |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT);
-		temp &= ~(RADEON_GRPH_START_REQ_MASK);
-		if ((rdev->family == CHIP_R350) &&
-		    (stop_req > 0x15)) {
-			stop_req -= 0x10;
-		}
-		temp |= (stop_req << RADEON_GRPH_START_REQ_SHIFT);
-		temp |= RADEON_GRPH_BUFFER_SIZE;
-		temp &= ~(RADEON_GRPH_CRITICAL_CNTL   |
-			  RADEON_GRPH_CRITICAL_AT_SOF |
-			  RADEON_GRPH_STOP_CNTL);
-		/*
-		  Write the result into the register.
-		*/
-		WREG32(RADEON_GRPH_BUFFER_CNTL, ((temp & ~RADEON_GRPH_CRITICAL_POINT_MASK) |
-						       (critical_point << RADEON_GRPH_CRITICAL_POINT_SHIFT)));
-
-#if 0
-		if ((rdev->family == CHIP_RS400) ||
-		    (rdev->family == CHIP_RS480)) {
-			/* attempt to program RS400 disp regs correctly ??? */
-			temp = RREG32(RS400_DISP1_REG_CNTL);
-			temp &= ~(RS400_DISP1_START_REQ_LEVEL_MASK |
-				  RS400_DISP1_STOP_REQ_LEVEL_MASK);
-			WREG32(RS400_DISP1_REQ_CNTL1, (temp |
-						       (critical_point << RS400_DISP1_START_REQ_LEVEL_SHIFT) |
-						       (critical_point << RS400_DISP1_STOP_REQ_LEVEL_SHIFT)));
-			temp = RREG32(RS400_DMIF_MEM_CNTL1);
-			temp &= ~(RS400_DISP1_CRITICAL_POINT_START_MASK |
-				  RS400_DISP1_CRITICAL_POINT_STOP_MASK);
-			WREG32(RS400_DMIF_MEM_CNTL1, (temp |
-						      (critical_point << RS400_DISP1_CRITICAL_POINT_START_SHIFT) |
-						      (critical_point << RS400_DISP1_CRITICAL_POINT_STOP_SHIFT)));
-		}
-#endif
-
-		DRM_DEBUG("GRPH_BUFFER_CNTL from to %x\n",
-			  /* 	  (unsigned int)info->SavedReg->grph_buffer_cntl, */
-			  (unsigned int)RREG32(RADEON_GRPH_BUFFER_CNTL));
-	}
-
-	if (mode2) {
-		u32 grph2_cntl;
-		stop_req = mode2->hdisplay * pixel_bytes2 / 16;
-
-		if (stop_req > max_stop_req)
-			stop_req = max_stop_req;
-
-		/*
-		  Find the drain rate of the display buffer.
-		*/
-		temp_ff.full = rfixed_const((16/pixel_bytes2));
-		disp_drain_rate2.full = rfixed_div(pix_clk2, temp_ff);
-
-		grph2_cntl = RREG32(RADEON_GRPH2_BUFFER_CNTL);
-		grph2_cntl &= ~(RADEON_GRPH_STOP_REQ_MASK);
-		grph2_cntl |= (stop_req << RADEON_GRPH_STOP_REQ_SHIFT);
-		grph2_cntl &= ~(RADEON_GRPH_START_REQ_MASK);
-		if ((rdev->family == CHIP_R350) &&
-		    (stop_req > 0x15)) {
-			stop_req -= 0x10;
-		}
-		grph2_cntl |= (stop_req << RADEON_GRPH_START_REQ_SHIFT);
-		grph2_cntl |= RADEON_GRPH_BUFFER_SIZE;
-		grph2_cntl &= ~(RADEON_GRPH_CRITICAL_CNTL   |
-			  RADEON_GRPH_CRITICAL_AT_SOF |
-			  RADEON_GRPH_STOP_CNTL);
-
-		if ((rdev->family == CHIP_RS100) ||
-		    (rdev->family == CHIP_RS200))
-			critical_point2 = 0;
-		else {
-			temp = (rdev->mc.vram_width * rdev->mc.vram_is_ddr + 1)/128;
-			temp_ff.full = rfixed_const(temp);
-			temp_ff.full = rfixed_mul(mclk_ff, temp_ff);
-			if (sclk_ff.full < temp_ff.full)
-				temp_ff.full = sclk_ff.full;
-
-			read_return_rate.full = temp_ff.full;
-
-			if (mode1) {
-				temp_ff.full = read_return_rate.full - disp_drain_rate.full;
-				time_disp1_drop_priority.full = rfixed_div(crit_point_ff, temp_ff);
-			} else {
-				time_disp1_drop_priority.full = 0;
-			}
-			crit_point_ff.full = disp_latency.full + time_disp1_drop_priority.full + disp_latency.full;
-			crit_point_ff.full = rfixed_mul(crit_point_ff, disp_drain_rate2);
-			crit_point_ff.full += rfixed_const_half(0);
-
-			critical_point2 = rfixed_trunc(crit_point_ff);
-
-			if (rdev->disp_priority == 2) {
-				critical_point2 = 0;
-			}
-
-			if (max_stop_req - critical_point2 < 4)
-				critical_point2 = 0;
-
-		}
-
-		if (critical_point2 == 0 && rdev->family == CHIP_R300) {
-			/* some R300 cards have problem with this set to 0 */
-			critical_point2 = 0x10;
-		}
-
-		WREG32(RADEON_GRPH2_BUFFER_CNTL, ((grph2_cntl & ~RADEON_GRPH_CRITICAL_POINT_MASK) |
-						  (critical_point2 << RADEON_GRPH_CRITICAL_POINT_SHIFT)));
-
-		if ((rdev->family == CHIP_RS400) ||
-		    (rdev->family == CHIP_RS480)) {
-#if 0
-			/* attempt to program RS400 disp2 regs correctly ??? */
-			temp = RREG32(RS400_DISP2_REQ_CNTL1);
-			temp &= ~(RS400_DISP2_START_REQ_LEVEL_MASK |
-				  RS400_DISP2_STOP_REQ_LEVEL_MASK);
-			WREG32(RS400_DISP2_REQ_CNTL1, (temp |
-						       (critical_point2 << RS400_DISP1_START_REQ_LEVEL_SHIFT) |
-						       (critical_point2 << RS400_DISP1_STOP_REQ_LEVEL_SHIFT)));
-			temp = RREG32(RS400_DISP2_REQ_CNTL2);
-			temp &= ~(RS400_DISP2_CRITICAL_POINT_START_MASK |
-				  RS400_DISP2_CRITICAL_POINT_STOP_MASK);
-			WREG32(RS400_DISP2_REQ_CNTL2, (temp |
-						       (critical_point2 << RS400_DISP2_CRITICAL_POINT_START_SHIFT) |
-						       (critical_point2 << RS400_DISP2_CRITICAL_POINT_STOP_SHIFT)));
-#endif
-			WREG32(RS400_DISP2_REQ_CNTL1, 0x105DC1CC);
-			WREG32(RS400_DISP2_REQ_CNTL2, 0x2749D000);
-			WREG32(RS400_DMIF_MEM_CNTL1,  0x29CA71DC);
-			WREG32(RS400_DISP1_REQ_CNTL1, 0x28FBC3AC);
-		}
-
-		DRM_DEBUG("GRPH2_BUFFER_CNTL from to %x\n",
-			  (unsigned int)RREG32(RADEON_GRPH2_BUFFER_CNTL));
-	}
-}
diff --git a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c
index 2c2f42de1d4..34d0f58eb94 100644
--- a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c
+++ b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c
@@ -30,170 +30,6 @@
 #include "atom.h"
 
 
-static void radeon_legacy_rmx_mode_set(struct drm_encoder *encoder,
-				       struct drm_display_mode *mode,
-				       struct drm_display_mode *adjusted_mode)
-{
-	struct drm_device *dev = encoder->dev;
-	struct radeon_device *rdev = dev->dev_private;
-	struct radeon_encoder *radeon_encoder = to_radeon_encoder(encoder);
-	int    xres = mode->hdisplay;
-	int    yres = mode->vdisplay;
-	bool   hscale = true, vscale = true;
-	int    hsync_wid;
-	int    vsync_wid;
-	int    hsync_start;
-	uint32_t scale, inc;
-	uint32_t fp_horz_stretch, fp_vert_stretch, crtc_more_cntl, fp_horz_vert_active;
-	uint32_t fp_h_sync_strt_wid, fp_v_sync_strt_wid, fp_crtc_h_total_disp, fp_crtc_v_total_disp;
-	struct radeon_native_mode *native_mode = &radeon_encoder->native_mode;
-
-	DRM_DEBUG("\n");
-
-	fp_vert_stretch = RREG32(RADEON_FP_VERT_STRETCH) &
-		(RADEON_VERT_STRETCH_RESERVED |
-		 RADEON_VERT_AUTO_RATIO_INC);
-	fp_horz_stretch = RREG32(RADEON_FP_HORZ_STRETCH) &
-		(RADEON_HORZ_FP_LOOP_STRETCH |
-		 RADEON_HORZ_AUTO_RATIO_INC);
-
-	crtc_more_cntl = 0;
-	if ((rdev->family == CHIP_RS100) ||
-	    (rdev->family == CHIP_RS200)) {
-		/* This is to workaround the asic bug for RMX, some versions
-		   of BIOS dosen't have this register initialized correctly. */
-		crtc_more_cntl |= RADEON_CRTC_H_CUTOFF_ACTIVE_EN;
-	}
-
-
-	fp_crtc_h_total_disp = ((((mode->crtc_htotal / 8) - 1) & 0x3ff)
-				| ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16));
-
-	hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8;
-	if (!hsync_wid)
-		hsync_wid = 1;
-	hsync_start = mode->crtc_hsync_start - 8;
-
-	fp_h_sync_strt_wid = ((hsync_start & 0x1fff)
-			      | ((hsync_wid & 0x3f) << 16)
-			      | ((mode->flags & DRM_MODE_FLAG_NHSYNC)
-				 ? RADEON_CRTC_H_SYNC_POL
-				 : 0));
-
-	fp_crtc_v_total_disp = (((mode->crtc_vtotal - 1) & 0xffff)
-				| ((mode->crtc_vdisplay - 1) << 16));
-
-	vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start;
-	if (!vsync_wid)
-		vsync_wid = 1;
-
-	fp_v_sync_strt_wid = (((mode->crtc_vsync_start - 1) & 0xfff)
-			      | ((vsync_wid & 0x1f) << 16)
-			      | ((mode->flags & DRM_MODE_FLAG_NVSYNC)
-				 ? RADEON_CRTC_V_SYNC_POL
-				 : 0));
-
-	fp_horz_vert_active = 0;
-
-	if (native_mode->panel_xres == 0 ||
-	    native_mode->panel_yres == 0) {
-		hscale = false;
-		vscale = false;
-	} else {
-		if (xres > native_mode->panel_xres)
-			xres = native_mode->panel_xres;
-		if (yres > native_mode->panel_yres)
-			yres = native_mode->panel_yres;
-
-		if (xres == native_mode->panel_xres)
-			hscale = false;
-		if (yres == native_mode->panel_yres)
-			vscale = false;
-	}
-
-	if (radeon_encoder->flags & RADEON_USE_RMX) {
-		if (radeon_encoder->rmx_type != RMX_CENTER) {
-			if (!hscale)
-				fp_horz_stretch |= ((xres/8-1) << 16);
-			else {
-				inc = (fp_horz_stretch & RADEON_HORZ_AUTO_RATIO_INC) ? 1 : 0;
-				scale = ((xres + inc) * RADEON_HORZ_STRETCH_RATIO_MAX)
-					/ native_mode->panel_xres + 1;
-				fp_horz_stretch |= (((scale) & RADEON_HORZ_STRETCH_RATIO_MASK) |
-						    RADEON_HORZ_STRETCH_BLEND |
-						    RADEON_HORZ_STRETCH_ENABLE |
-						    ((native_mode->panel_xres/8-1) << 16));
-			}
-
-			if (!vscale)
-				fp_vert_stretch |= ((yres-1) << 12);
-			else {
-				inc = (fp_vert_stretch & RADEON_VERT_AUTO_RATIO_INC) ? 1 : 0;
-				scale = ((yres + inc) * RADEON_VERT_STRETCH_RATIO_MAX)
-					/ native_mode->panel_yres + 1;
-				fp_vert_stretch |= (((scale) & RADEON_VERT_STRETCH_RATIO_MASK) |
-						    RADEON_VERT_STRETCH_ENABLE |
-						    RADEON_VERT_STRETCH_BLEND |
-						    ((native_mode->panel_yres-1) << 12));
-			}
-		} else if (radeon_encoder->rmx_type == RMX_CENTER) {
-			int    blank_width;
-
-			fp_horz_stretch |= ((xres/8-1) << 16);
-			fp_vert_stretch |= ((yres-1) << 12);
-
-			crtc_more_cntl |= (RADEON_CRTC_AUTO_HORZ_CENTER_EN |
-					   RADEON_CRTC_AUTO_VERT_CENTER_EN);
-
-			blank_width = (mode->crtc_hblank_end - mode->crtc_hblank_start) / 8;
-			if (blank_width > 110)
-				blank_width = 110;
-
-			fp_crtc_h_total_disp = (((blank_width) & 0x3ff)
-						| ((((mode->crtc_hdisplay / 8) - 1) & 0x1ff) << 16));
-
-			hsync_wid = (mode->crtc_hsync_end - mode->crtc_hsync_start) / 8;
-			if (!hsync_wid)
-				hsync_wid = 1;
-
-			fp_h_sync_strt_wid = ((((mode->crtc_hsync_start - mode->crtc_hblank_start) / 8) & 0x1fff)
-					      | ((hsync_wid & 0x3f) << 16)
-					      | ((mode->flags & DRM_MODE_FLAG_NHSYNC)
-						 ? RADEON_CRTC_H_SYNC_POL
-						 : 0));
-
-			fp_crtc_v_total_disp = (((mode->crtc_vblank_end - mode->crtc_vblank_start) & 0xffff)
-						| ((mode->crtc_vdisplay - 1) << 16));
-
-			vsync_wid = mode->crtc_vsync_end - mode->crtc_vsync_start;
-			if (!vsync_wid)
-				vsync_wid = 1;
-
-			fp_v_sync_strt_wid = ((((mode->crtc_vsync_start - mode->crtc_vblank_start) & 0xfff)
-					       | ((vsync_wid & 0x1f) << 16)
-					       | ((mode->flags & DRM_MODE_FLAG_NVSYNC)
-						  ? RADEON_CRTC_V_SYNC_POL
-						  : 0)));
-
-			fp_horz_vert_active = (((native_mode->panel_yres) & 0xfff) |
-					       (((native_mode->panel_xres / 8) & 0x1ff) << 16));
-		}
-	} else {
-		fp_horz_stretch |= ((xres/8-1) << 16);
-		fp_vert_stretch |= ((yres-1) << 12);
-	}
-
-	WREG32(RADEON_FP_HORZ_STRETCH,      fp_horz_stretch);
-	WREG32(RADEON_FP_VERT_STRETCH,      fp_vert_stretch);
-	WREG32(RADEON_CRTC_MORE_CNTL,       crtc_more_cntl);
-	WREG32(RADEON_FP_HORZ_VERT_ACTIVE,  fp_horz_vert_active);
-	WREG32(RADEON_FP_H_SYNC_STRT_WID,   fp_h_sync_strt_wid);
-	WREG32(RADEON_FP_V_SYNC_STRT_WID,   fp_v_sync_strt_wid);
-	WREG32(RADEON_FP_CRTC_H_TOTAL_DISP, fp_crtc_h_total_disp);
-	WREG32(RADEON_FP_CRTC_V_TOTAL_DISP, fp_crtc_v_total_disp);
-
-}
-
 static void radeon_legacy_lvds_dpms(struct drm_encoder *encoder, int mode)
 {
 	struct drm_device *dev = encoder->dev;
@@ -287,9 +123,6 @@ static void radeon_legacy_lvds_mode_set(struct drm_encoder *encoder,
 
 	DRM_DEBUG("\n");
 
-	if (radeon_crtc->crtc_id == 0)
-		radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode);
-
 	lvds_pll_cntl = RREG32(RADEON_LVDS_PLL_CNTL);
 	lvds_pll_cntl &= ~RADEON_LVDS_PLL_EN;
 
@@ -318,7 +151,7 @@ static void radeon_legacy_lvds_mode_set(struct drm_encoder *encoder,
 
 	if (radeon_crtc->crtc_id == 0) {
 		if (ASIC_IS_R300(rdev)) {
-			if (radeon_encoder->flags & RADEON_USE_RMX)
+			if (radeon_encoder->rmx_type != RMX_OFF)
 				lvds_pll_cntl |= R300_LVDS_SRC_SEL_RMX;
 		} else
 			lvds_gen_cntl &= ~RADEON_LVDS_SEL_CRTC2;
@@ -350,8 +183,6 @@ static bool radeon_legacy_lvds_mode_fixup(struct drm_encoder *encoder,
 
 	drm_mode_set_crtcinfo(adjusted_mode, 0);
 
-	radeon_encoder->flags &= ~RADEON_USE_RMX;
-
 	if (radeon_encoder->rmx_type != RMX_OFF)
 		radeon_rmx_mode_fixup(encoder, mode, adjusted_mode);
 
@@ -455,9 +286,6 @@ static void radeon_legacy_primary_dac_mode_set(struct drm_encoder *encoder,
 
 	DRM_DEBUG("\n");
 
-	if (radeon_crtc->crtc_id == 0)
-		radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode);
-
 	if (radeon_crtc->crtc_id == 0) {
 		if (rdev->family == CHIP_R200 || ASIC_IS_R300(rdev)) {
 			disp_output_cntl = RREG32(RADEON_DISP_OUTPUT_CNTL) &
@@ -653,9 +481,6 @@ static void radeon_legacy_tmds_int_mode_set(struct drm_encoder *encoder,
 
 	DRM_DEBUG("\n");
 
-	if (radeon_crtc->crtc_id == 0)
-		radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode);
-
 	tmp = tmds_pll_cntl = RREG32(RADEON_TMDS_PLL_CNTL);
 	tmp &= 0xfffff;
 	if (rdev->family == CHIP_RV280) {
@@ -711,7 +536,7 @@ static void radeon_legacy_tmds_int_mode_set(struct drm_encoder *encoder,
     if (radeon_crtc->crtc_id == 0) {
 	    if (ASIC_IS_R300(rdev) || rdev->family == CHIP_R200) {
 		    fp_gen_cntl &= ~R200_FP_SOURCE_SEL_MASK;
-		    if (radeon_encoder->flags & RADEON_USE_RMX)
+		    if (radeon_encoder->rmx_type != RMX_OFF)
 			    fp_gen_cntl |= R200_FP_SOURCE_SEL_RMX;
 		    else
 			    fp_gen_cntl |= R200_FP_SOURCE_SEL_CRTC1;
@@ -820,9 +645,6 @@ static void radeon_legacy_tmds_ext_mode_set(struct drm_encoder *encoder,
 
 	DRM_DEBUG("\n");
 
-	if (radeon_crtc->crtc_id == 0)
-		radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode);
-
 	if (rdev->is_atom_bios) {
 		radeon_encoder->pixel_clock = adjusted_mode->clock;
 		atombios_external_tmds_setup(encoder, ATOM_ENABLE);
@@ -856,7 +678,7 @@ static void radeon_legacy_tmds_ext_mode_set(struct drm_encoder *encoder,
 	if (radeon_crtc->crtc_id == 0) {
 		if ((rdev->family == CHIP_R200) || ASIC_IS_R300(rdev)) {
 			fp2_gen_cntl &= ~R200_FP2_SOURCE_SEL_MASK;
-			if (radeon_encoder->flags & RADEON_USE_RMX)
+			if (radeon_encoder->rmx_type != RMX_OFF)
 				fp2_gen_cntl |= R200_FP2_SOURCE_SEL_RMX;
 			else
 				fp2_gen_cntl |= R200_FP2_SOURCE_SEL_CRTC1;
@@ -1014,9 +836,6 @@ static void radeon_legacy_tv_dac_mode_set(struct drm_encoder *encoder,
 
 	DRM_DEBUG("\n");
 
-	if (radeon_crtc->crtc_id == 0)
-		radeon_legacy_rmx_mode_set(encoder, mode, adjusted_mode);
-
 	if (rdev->family != CHIP_R200) {
 		tv_dac_cntl = RREG32(RADEON_TV_DAC_CNTL);
 		if (rdev->family == CHIP_R420 ||
@@ -1243,6 +1062,7 @@ radeon_add_legacy_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t
 
 	radeon_encoder->encoder_id = encoder_id;
 	radeon_encoder->devices = supported_device;
+	radeon_encoder->rmx_type = RMX_OFF;
 
 	switch (radeon_encoder->encoder_id) {
 	case ENCODER_OBJECT_ID_INTERNAL_LVDS:
diff --git a/drivers/gpu/drm/radeon/radeon_mode.h b/drivers/gpu/drm/radeon/radeon_mode.h
index ba89b59f6e5..3b09a1f2d8f 100644
--- a/drivers/gpu/drm/radeon/radeon_mode.h
+++ b/drivers/gpu/drm/radeon/radeon_mode.h
@@ -36,6 +36,9 @@
 #include <linux/i2c.h>
 #include <linux/i2c-id.h>
 #include <linux/i2c-algo-bit.h>
+#include "radeon_fixed.h"
+
+struct radeon_device;
 
 #define to_radeon_crtc(x) container_of(x, struct radeon_crtc, base)
 #define to_radeon_connector(x) container_of(x, struct radeon_connector, base)
@@ -171,6 +174,18 @@ struct radeon_mode_info {
 	struct atom_context *atom_context;
 	enum radeon_connector_table connector_table;
 	bool mode_config_initialized;
+	struct radeon_crtc *crtcs[2];
+};
+
+struct radeon_native_mode {
+	/* preferred mode */
+	uint32_t panel_xres, panel_yres;
+	uint32_t hoverplus, hsync_width;
+	uint32_t hblank;
+	uint32_t voverplus, vsync_width;
+	uint32_t vblank;
+	uint32_t dotclock;
+	uint32_t flags;
 };
 
 struct radeon_crtc {
@@ -188,19 +203,11 @@ struct radeon_crtc {
 	int cursor_height;
 	uint32_t legacy_display_base_addr;
 	uint32_t legacy_cursor_offset;
-};
-
-#define RADEON_USE_RMX 1
-
-struct radeon_native_mode {
-	/* preferred mode */
-	uint32_t panel_xres, panel_yres;
-	uint32_t hoverplus, hsync_width;
-	uint32_t hblank;
-	uint32_t voverplus, vsync_width;
-	uint32_t vblank;
-	uint32_t dotclock;
-	uint32_t flags;
+	enum radeon_rmx_type rmx_type;
+	uint32_t devices;
+	fixed20_12 vsc;
+	fixed20_12 hsc;
+	struct radeon_native_mode native_mode;
 };
 
 struct radeon_encoder_primary_dac {
@@ -386,16 +393,9 @@ void radeon_enc_destroy(struct drm_encoder *encoder);
 void radeon_copy_fb(struct drm_device *dev, struct drm_gem_object *dst_obj);
 void radeon_combios_asic_init(struct drm_device *dev);
 extern int radeon_static_clocks_init(struct drm_device *dev);
-void radeon_init_disp_bw_legacy(struct drm_device *dev,
-				struct drm_display_mode *mode1,
-				uint32_t pixel_bytes1,
-				struct drm_display_mode *mode2,
-				uint32_t pixel_bytes2);
-void radeon_init_disp_bw_avivo(struct drm_device *dev,
-			       struct drm_display_mode *mode1,
-			       uint32_t pixel_bytes1,
-			       struct drm_display_mode *mode2,
-			       uint32_t pixel_bytes2);
-void radeon_init_disp_bandwidth(struct drm_device *dev);
+bool radeon_crtc_scaling_mode_fixup(struct drm_crtc *crtc,
+					struct drm_display_mode *mode,
+					struct drm_display_mode *adjusted_mode);
+void atom_rv515_force_tv_scaler(struct radeon_device *rdev);
 
 #endif
diff --git a/drivers/gpu/drm/radeon/radeon_share.h b/drivers/gpu/drm/radeon/radeon_share.h
new file mode 100644
index 00000000000..63a773578f1
--- /dev/null
+++ b/drivers/gpu/drm/radeon/radeon_share.h
@@ -0,0 +1,39 @@
+/*
+ * Copyright 2008 Advanced Micro Devices, Inc.
+ * Copyright 2008 Red Hat Inc.
+ * Copyright 2009 Jerome Glisse.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: Dave Airlie
+ *          Alex Deucher
+ *          Jerome Glisse
+ */
+#ifndef __RADEON_SHARE_H__
+#define __RADEON_SHARE_H__
+
+void r100_vram_init_sizes(struct radeon_device *rdev);
+
+void rs690_line_buffer_adjust(struct radeon_device *rdev,
+			      struct drm_display_mode *mode1,
+			      struct drm_display_mode *mode2);
+
+void rv515_bandwidth_avivo_update(struct radeon_device *rdev);
+
+#endif
diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c
index daf24e85cba..96a3c8486d2 100644
--- a/drivers/gpu/drm/radeon/rs400.c
+++ b/drivers/gpu/drm/radeon/rs400.c
@@ -29,6 +29,7 @@
 #include <drm/drmP.h>
 #include "radeon_reg.h"
 #include "radeon.h"
+#include "radeon_share.h"
 
 /* rs400,rs480 depends on : */
 void r100_hdp_reset(struct radeon_device *rdev);
diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c
index ab0c967553e..bccdce7fd37 100644
--- a/drivers/gpu/drm/radeon/rs600.c
+++ b/drivers/gpu/drm/radeon/rs600.c
@@ -301,6 +301,11 @@ void rs600_vram_info(struct radeon_device *rdev)
 	rdev->mc.vram_width = 128;
 }
 
+void rs600_bandwidth_update(struct radeon_device *rdev)
+{
+	/* FIXME: implement, should this be like rs690 ? */
+}
+
 
 /*
  * Indirect registers accessor
diff --git a/drivers/gpu/drm/radeon/rs690.c b/drivers/gpu/drm/radeon/rs690.c
index 79ba85042b5..97eaee3d28b 100644
--- a/drivers/gpu/drm/radeon/rs690.c
+++ b/drivers/gpu/drm/radeon/rs690.c
@@ -28,6 +28,9 @@
 #include "drmP.h"
 #include "radeon_reg.h"
 #include "radeon.h"
+#include "rs690r.h"
+#include "atom.h"
+#include "atom-bits.h"
 
 /* rs690,rs740 depends on : */
 void r100_hdp_reset(struct radeon_device *rdev);
@@ -138,9 +141,82 @@ void rs690_gpu_init(struct radeon_device *rdev)
 /*
  * VRAM info.
  */
+void rs690_pm_info(struct radeon_device *rdev)
+{
+	int index = GetIndexIntoMasterTable(DATA, IntegratedSystemInfo);
+	struct _ATOM_INTEGRATED_SYSTEM_INFO *info;
+	struct _ATOM_INTEGRATED_SYSTEM_INFO_V2 *info_v2;
+	void *ptr;
+	uint16_t data_offset;
+	uint8_t frev, crev;
+	fixed20_12 tmp;
+
+	atom_parse_data_header(rdev->mode_info.atom_context, index, NULL,
+			       &frev, &crev, &data_offset);
+	ptr = rdev->mode_info.atom_context->bios + data_offset;
+	info = (struct _ATOM_INTEGRATED_SYSTEM_INFO *)ptr;
+	info_v2 = (struct _ATOM_INTEGRATED_SYSTEM_INFO_V2 *)ptr;
+	/* Get various system informations from bios */
+	switch (crev) {
+	case 1:
+		tmp.full = rfixed_const(100);
+		rdev->pm.igp_sideport_mclk.full = rfixed_const(info->ulBootUpMemoryClock);
+		rdev->pm.igp_sideport_mclk.full = rfixed_div(rdev->pm.igp_sideport_mclk, tmp);
+		rdev->pm.igp_system_mclk.full = rfixed_const(le16_to_cpu(info->usK8MemoryClock));
+		rdev->pm.igp_ht_link_clk.full = rfixed_const(le16_to_cpu(info->usFSBClock));
+		rdev->pm.igp_ht_link_width.full = rfixed_const(info->ucHTLinkWidth);
+		break;
+	case 2:
+		tmp.full = rfixed_const(100);
+		rdev->pm.igp_sideport_mclk.full = rfixed_const(info_v2->ulBootUpSidePortClock);
+		rdev->pm.igp_sideport_mclk.full = rfixed_div(rdev->pm.igp_sideport_mclk, tmp);
+		rdev->pm.igp_system_mclk.full = rfixed_const(info_v2->ulBootUpUMAClock);
+		rdev->pm.igp_system_mclk.full = rfixed_div(rdev->pm.igp_system_mclk, tmp);
+		rdev->pm.igp_ht_link_clk.full = rfixed_const(info_v2->ulHTLinkFreq);
+		rdev->pm.igp_ht_link_clk.full = rfixed_div(rdev->pm.igp_ht_link_clk, tmp);
+		rdev->pm.igp_ht_link_width.full = rfixed_const(le16_to_cpu(info_v2->usMinHTLinkWidth));
+		break;
+	default:
+		tmp.full = rfixed_const(100);
+		/* We assume the slower possible clock ie worst case */
+		/* DDR 333Mhz */
+		rdev->pm.igp_sideport_mclk.full = rfixed_const(333);
+		/* FIXME: system clock ? */
+		rdev->pm.igp_system_mclk.full = rfixed_const(100);
+		rdev->pm.igp_system_mclk.full = rfixed_div(rdev->pm.igp_system_mclk, tmp);
+		rdev->pm.igp_ht_link_clk.full = rfixed_const(200);
+		rdev->pm.igp_ht_link_width.full = rfixed_const(8);
+		DRM_ERROR("No integrated system info for your GPU, using safe default\n");
+		break;
+	}
+	/* Compute various bandwidth */
+	/* k8_bandwidth = (memory_clk / 2) * 2 * 8 * 0.5 = memory_clk * 4  */
+	tmp.full = rfixed_const(4);
+	rdev->pm.k8_bandwidth.full = rfixed_mul(rdev->pm.igp_system_mclk, tmp);
+	/* ht_bandwidth = ht_clk * 2 * ht_width / 8 * 0.8
+	 *              = ht_clk * ht_width / 5
+	 */
+	tmp.full = rfixed_const(5);
+	rdev->pm.ht_bandwidth.full = rfixed_mul(rdev->pm.igp_ht_link_clk,
+						rdev->pm.igp_ht_link_width);
+	rdev->pm.ht_bandwidth.full = rfixed_div(rdev->pm.ht_bandwidth, tmp);
+	if (tmp.full < rdev->pm.max_bandwidth.full) {
+		/* HT link is a limiting factor */
+		rdev->pm.max_bandwidth.full = tmp.full;
+	}
+	/* sideport_bandwidth = (sideport_clk / 2) * 2 * 2 * 0.7
+	 *                    = (sideport_clk * 14) / 10
+	 */
+	tmp.full = rfixed_const(14);
+	rdev->pm.sideport_bandwidth.full = rfixed_mul(rdev->pm.igp_sideport_mclk, tmp);
+	tmp.full = rfixed_const(10);
+	rdev->pm.sideport_bandwidth.full = rfixed_div(rdev->pm.sideport_bandwidth, tmp);
+}
+
 void rs690_vram_info(struct radeon_device *rdev)
 {
 	uint32_t tmp;
+	fixed20_12 a;
 
 	rs400_gart_adjust_size(rdev);
 	/* DDR for all card after R300 & IGP */
@@ -156,8 +232,404 @@ void rs690_vram_info(struct radeon_device *rdev)
 
 	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
 	rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0);
+	rs690_pm_info(rdev);
+	/* FIXME: we should enforce default clock in case GPU is not in
+	 * default setup
+	 */
+	a.full = rfixed_const(100);
+	rdev->pm.sclk.full = rfixed_const(rdev->clock.default_sclk);
+	rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a);
+	a.full = rfixed_const(16);
+	/* core_bandwidth = sclk(Mhz) * 16 */
+	rdev->pm.core_bandwidth.full = rfixed_div(rdev->pm.sclk, a);
+}
+
+void rs690_line_buffer_adjust(struct radeon_device *rdev,
+			      struct drm_display_mode *mode1,
+			      struct drm_display_mode *mode2)
+{
+	u32 tmp;
+
+	/*
+	 * Line Buffer Setup
+	 * There is a single line buffer shared by both display controllers.
+	 * DC_LB_MEMORY_SPLIT controls how that line buffer is shared between
+	 * the display controllers.  The paritioning can either be done
+	 * manually or via one of four preset allocations specified in bits 1:0:
+	 *  0 - line buffer is divided in half and shared between crtc
+	 *  1 - D1 gets 3/4 of the line buffer, D2 gets 1/4
+	 *  2 - D1 gets the whole buffer
+	 *  3 - D1 gets 1/4 of the line buffer, D2 gets 3/4
+	 * Setting bit 2 of DC_LB_MEMORY_SPLIT controls switches to manual
+	 * allocation mode. In manual allocation mode, D1 always starts at 0,
+	 * D1 end/2 is specified in bits 14:4; D2 allocation follows D1.
+	 */
+	tmp = RREG32(DC_LB_MEMORY_SPLIT) & ~DC_LB_MEMORY_SPLIT_MASK;
+	tmp &= ~DC_LB_MEMORY_SPLIT_SHIFT_MODE;
+	/* auto */
+	if (mode1 && mode2) {
+		if (mode1->hdisplay > mode2->hdisplay) {
+			if (mode1->hdisplay > 2560)
+				tmp |= DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q;
+			else
+				tmp |= DC_LB_MEMORY_SPLIT_D1HALF_D2HALF;
+		} else if (mode2->hdisplay > mode1->hdisplay) {
+			if (mode2->hdisplay > 2560)
+				tmp |= DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q;
+			else
+				tmp |= DC_LB_MEMORY_SPLIT_D1HALF_D2HALF;
+		} else
+			tmp |= AVIVO_DC_LB_MEMORY_SPLIT_D1HALF_D2HALF;
+	} else if (mode1) {
+		tmp |= DC_LB_MEMORY_SPLIT_D1_ONLY;
+	} else if (mode2) {
+		tmp |= DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q;
+	}
+	WREG32(DC_LB_MEMORY_SPLIT, tmp);
 }
 
+struct rs690_watermark {
+	u32        lb_request_fifo_depth;
+	fixed20_12 num_line_pair;
+	fixed20_12 estimated_width;
+	fixed20_12 worst_case_latency;
+	fixed20_12 consumption_rate;
+	fixed20_12 active_time;
+	fixed20_12 dbpp;
+	fixed20_12 priority_mark_max;
+	fixed20_12 priority_mark;
+	fixed20_12 sclk;
+};
+
+void rs690_crtc_bandwidth_compute(struct radeon_device *rdev,
+				  struct radeon_crtc *crtc,
+				  struct rs690_watermark *wm)
+{
+	struct drm_display_mode *mode = &crtc->base.mode;
+	fixed20_12 a, b, c;
+	fixed20_12 pclk, request_fifo_depth, tolerable_latency, estimated_width;
+	fixed20_12 consumption_time, line_time, chunk_time, read_delay_latency;
+	/* FIXME: detect IGP with sideport memory, i don't think there is any
+	 * such product available
+	 */
+	bool sideport = false;
+
+	if (!crtc->base.enabled) {
+		/* FIXME: wouldn't it better to set priority mark to maximum */
+		wm->lb_request_fifo_depth = 4;
+		return;
+	}
+
+	if (crtc->vsc.full > rfixed_const(2))
+		wm->num_line_pair.full = rfixed_const(2);
+	else
+		wm->num_line_pair.full = rfixed_const(1);
+
+	b.full = rfixed_const(mode->crtc_hdisplay);
+	c.full = rfixed_const(256);
+	a.full = rfixed_mul(wm->num_line_pair, b);
+	request_fifo_depth.full = rfixed_div(a, c);
+	if (a.full < rfixed_const(4)) {
+		wm->lb_request_fifo_depth = 4;
+	} else {
+		wm->lb_request_fifo_depth = rfixed_trunc(request_fifo_depth);
+	}
+
+	/* Determine consumption rate
+	 *  pclk = pixel clock period(ns) = 1000 / (mode.clock / 1000)
+	 *  vtaps = number of vertical taps,
+	 *  vsc = vertical scaling ratio, defined as source/destination
+	 *  hsc = horizontal scaling ration, defined as source/destination
+	 */
+	a.full = rfixed_const(mode->clock);
+	b.full = rfixed_const(1000);
+	a.full = rfixed_div(a, b);
+	pclk.full = rfixed_div(b, a);
+	if (crtc->rmx_type != RMX_OFF) {
+		b.full = rfixed_const(2);
+		if (crtc->vsc.full > b.full)
+			b.full = crtc->vsc.full;
+		b.full = rfixed_mul(b, crtc->hsc);
+		c.full = rfixed_const(2);
+		b.full = rfixed_div(b, c);
+		consumption_time.full = rfixed_div(pclk, b);
+	} else {
+		consumption_time.full = pclk.full;
+	}
+	a.full = rfixed_const(1);
+	wm->consumption_rate.full = rfixed_div(a, consumption_time);
+
+
+	/* Determine line time
+	 *  LineTime = total time for one line of displayhtotal
+	 *  LineTime = total number of horizontal pixels
+	 *  pclk = pixel clock period(ns)
+	 */
+	a.full = rfixed_const(crtc->base.mode.crtc_htotal);
+	line_time.full = rfixed_mul(a, pclk);
+
+	/* Determine active time
+	 *  ActiveTime = time of active region of display within one line,
+	 *  hactive = total number of horizontal active pixels
+	 *  htotal = total number of horizontal pixels
+	 */
+	a.full = rfixed_const(crtc->base.mode.crtc_htotal);
+	b.full = rfixed_const(crtc->base.mode.crtc_hdisplay);
+	wm->active_time.full = rfixed_mul(line_time, b);
+	wm->active_time.full = rfixed_div(wm->active_time, a);
+
+	/* Maximun bandwidth is the minimun bandwidth of all component */
+	rdev->pm.max_bandwidth = rdev->pm.core_bandwidth;
+	if (sideport) {
+		if (rdev->pm.max_bandwidth.full > rdev->pm.sideport_bandwidth.full &&
+			rdev->pm.sideport_bandwidth.full)
+			rdev->pm.max_bandwidth = rdev->pm.sideport_bandwidth;
+		read_delay_latency.full = rfixed_const(370 * 800 * 1000);
+		read_delay_latency.full = rfixed_div(read_delay_latency,
+			rdev->pm.igp_sideport_mclk);
+	} else {
+		if (rdev->pm.max_bandwidth.full > rdev->pm.k8_bandwidth.full &&
+			rdev->pm.k8_bandwidth.full)
+			rdev->pm.max_bandwidth = rdev->pm.k8_bandwidth;
+		if (rdev->pm.max_bandwidth.full > rdev->pm.ht_bandwidth.full &&
+			rdev->pm.ht_bandwidth.full)
+			rdev->pm.max_bandwidth = rdev->pm.ht_bandwidth;
+		read_delay_latency.full = rfixed_const(5000);
+	}
+
+	/* sclk = system clocks(ns) = 1000 / max_bandwidth / 16 */
+	a.full = rfixed_const(16);
+	rdev->pm.sclk.full = rfixed_mul(rdev->pm.max_bandwidth, a);
+	a.full = rfixed_const(1000);
+	rdev->pm.sclk.full = rfixed_div(a, rdev->pm.sclk);
+	/* Determine chunk time
+	 * ChunkTime = the time it takes the DCP to send one chunk of data
+	 * to the LB which consists of pipeline delay and inter chunk gap
+	 * sclk = system clock(ns)
+	 */
+	a.full = rfixed_const(256 * 13);
+	chunk_time.full = rfixed_mul(rdev->pm.sclk, a);
+	a.full = rfixed_const(10);
+	chunk_time.full = rfixed_div(chunk_time, a);
+
+	/* Determine the worst case latency
+	 * NumLinePair = Number of line pairs to request(1=2 lines, 2=4 lines)
+	 * WorstCaseLatency = worst case time from urgent to when the MC starts
+	 *                    to return data
+	 * READ_DELAY_IDLE_MAX = constant of 1us
+	 * ChunkTime = time it takes the DCP to send one chunk of data to the LB
+	 *             which consists of pipeline delay and inter chunk gap
+	 */
+	if (rfixed_trunc(wm->num_line_pair) > 1) {
+		a.full = rfixed_const(3);
+		wm->worst_case_latency.full = rfixed_mul(a, chunk_time);
+		wm->worst_case_latency.full += read_delay_latency.full;
+	} else {
+		a.full = rfixed_const(2);
+		wm->worst_case_latency.full = rfixed_mul(a, chunk_time);
+		wm->worst_case_latency.full += read_delay_latency.full;
+	}
+
+	/* Determine the tolerable latency
+	 * TolerableLatency = Any given request has only 1 line time
+	 *                    for the data to be returned
+	 * LBRequestFifoDepth = Number of chunk requests the LB can
+	 *                      put into the request FIFO for a display
+	 *  LineTime = total time for one line of display
+	 *  ChunkTime = the time it takes the DCP to send one chunk
+	 *              of data to the LB which consists of
+	 *  pipeline delay and inter chunk gap
+	 */
+	if ((2+wm->lb_request_fifo_depth) >= rfixed_trunc(request_fifo_depth)) {
+		tolerable_latency.full = line_time.full;
+	} else {
+		tolerable_latency.full = rfixed_const(wm->lb_request_fifo_depth - 2);
+		tolerable_latency.full = request_fifo_depth.full - tolerable_latency.full;
+		tolerable_latency.full = rfixed_mul(tolerable_latency, chunk_time);
+		tolerable_latency.full = line_time.full - tolerable_latency.full;
+	}
+	/* We assume worst case 32bits (4 bytes) */
+	wm->dbpp.full = rfixed_const(4 * 8);
+
+	/* Determine the maximum priority mark
+	 *  width = viewport width in pixels
+	 */
+	a.full = rfixed_const(16);
+	wm->priority_mark_max.full = rfixed_const(crtc->base.mode.crtc_hdisplay);
+	wm->priority_mark_max.full = rfixed_div(wm->priority_mark_max, a);
+
+	/* Determine estimated width */
+	estimated_width.full = tolerable_latency.full - wm->worst_case_latency.full;
+	estimated_width.full = rfixed_div(estimated_width, consumption_time);
+	if (rfixed_trunc(estimated_width) > crtc->base.mode.crtc_hdisplay) {
+		wm->priority_mark.full = rfixed_const(10);
+	} else {
+		a.full = rfixed_const(16);
+		wm->priority_mark.full = rfixed_div(estimated_width, a);
+		wm->priority_mark.full = wm->priority_mark_max.full - wm->priority_mark.full;
+	}
+}
+
+void rs690_bandwidth_update(struct radeon_device *rdev)
+{
+	struct drm_display_mode *mode0 = NULL;
+	struct drm_display_mode *mode1 = NULL;
+	struct rs690_watermark wm0;
+	struct rs690_watermark wm1;
+	u32 tmp;
+	fixed20_12 priority_mark02, priority_mark12, fill_rate;
+	fixed20_12 a, b;
+
+	if (rdev->mode_info.crtcs[0]->base.enabled)
+		mode0 = &rdev->mode_info.crtcs[0]->base.mode;
+	if (rdev->mode_info.crtcs[1]->base.enabled)
+		mode1 = &rdev->mode_info.crtcs[1]->base.mode;
+	/*
+	 * Set display0/1 priority up in the memory controller for
+	 * modes if the user specifies HIGH for displaypriority
+	 * option.
+	 */
+	if (rdev->disp_priority == 2) {
+		tmp = RREG32_MC(MC_INIT_MISC_LAT_TIMER);
+		tmp &= ~MC_DISP1R_INIT_LAT_MASK;
+		tmp &= ~MC_DISP0R_INIT_LAT_MASK;
+		if (mode1)
+			tmp |= (1 << MC_DISP1R_INIT_LAT_SHIFT);
+		if (mode0)
+			tmp |= (1 << MC_DISP0R_INIT_LAT_SHIFT);
+		WREG32_MC(MC_INIT_MISC_LAT_TIMER, tmp);
+	}
+	rs690_line_buffer_adjust(rdev, mode0, mode1);
+
+	if ((rdev->family == CHIP_RS690) || (rdev->family == CHIP_RS740))
+		WREG32(DCP_CONTROL, 0);
+	if ((rdev->family == CHIP_RS780) || (rdev->family == CHIP_RS880))
+		WREG32(DCP_CONTROL, 2);
+
+	rs690_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[0], &wm0);
+	rs690_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[1], &wm1);
+
+	tmp = (wm0.lb_request_fifo_depth - 1);
+	tmp |= (wm1.lb_request_fifo_depth - 1) << 16;
+	WREG32(LB_MAX_REQ_OUTSTANDING, tmp);
+
+	if (mode0 && mode1) {
+		if (rfixed_trunc(wm0.dbpp) > 64)
+			a.full = rfixed_mul(wm0.dbpp, wm0.num_line_pair);
+		else
+			a.full = wm0.num_line_pair.full;
+		if (rfixed_trunc(wm1.dbpp) > 64)
+			b.full = rfixed_mul(wm1.dbpp, wm1.num_line_pair);
+		else
+			b.full = wm1.num_line_pair.full;
+		a.full += b.full;
+		fill_rate.full = rfixed_div(wm0.sclk, a);
+		if (wm0.consumption_rate.full > fill_rate.full) {
+			b.full = wm0.consumption_rate.full - fill_rate.full;
+			b.full = rfixed_mul(b, wm0.active_time);
+			a.full = rfixed_mul(wm0.worst_case_latency,
+						wm0.consumption_rate);
+			a.full = a.full + b.full;
+			b.full = rfixed_const(16 * 1000);
+			priority_mark02.full = rfixed_div(a, b);
+		} else {
+			a.full = rfixed_mul(wm0.worst_case_latency,
+						wm0.consumption_rate);
+			b.full = rfixed_const(16 * 1000);
+			priority_mark02.full = rfixed_div(a, b);
+		}
+		if (wm1.consumption_rate.full > fill_rate.full) {
+			b.full = wm1.consumption_rate.full - fill_rate.full;
+			b.full = rfixed_mul(b, wm1.active_time);
+			a.full = rfixed_mul(wm1.worst_case_latency,
+						wm1.consumption_rate);
+			a.full = a.full + b.full;
+			b.full = rfixed_const(16 * 1000);
+			priority_mark12.full = rfixed_div(a, b);
+		} else {
+			a.full = rfixed_mul(wm1.worst_case_latency,
+						wm1.consumption_rate);
+			b.full = rfixed_const(16 * 1000);
+			priority_mark12.full = rfixed_div(a, b);
+		}
+		if (wm0.priority_mark.full > priority_mark02.full)
+			priority_mark02.full = wm0.priority_mark.full;
+		if (rfixed_trunc(priority_mark02) < 0)
+			priority_mark02.full = 0;
+		if (wm0.priority_mark_max.full > priority_mark02.full)
+			priority_mark02.full = wm0.priority_mark_max.full;
+		if (wm1.priority_mark.full > priority_mark12.full)
+			priority_mark12.full = wm1.priority_mark.full;
+		if (rfixed_trunc(priority_mark12) < 0)
+			priority_mark12.full = 0;
+		if (wm1.priority_mark_max.full > priority_mark12.full)
+			priority_mark12.full = wm1.priority_mark_max.full;
+		WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02));
+		WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02));
+		WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12));
+		WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12));
+	} else if (mode0) {
+		if (rfixed_trunc(wm0.dbpp) > 64)
+			a.full = rfixed_mul(wm0.dbpp, wm0.num_line_pair);
+		else
+			a.full = wm0.num_line_pair.full;
+		fill_rate.full = rfixed_div(wm0.sclk, a);
+		if (wm0.consumption_rate.full > fill_rate.full) {
+			b.full = wm0.consumption_rate.full - fill_rate.full;
+			b.full = rfixed_mul(b, wm0.active_time);
+			a.full = rfixed_mul(wm0.worst_case_latency,
+						wm0.consumption_rate);
+			a.full = a.full + b.full;
+			b.full = rfixed_const(16 * 1000);
+			priority_mark02.full = rfixed_div(a, b);
+		} else {
+			a.full = rfixed_mul(wm0.worst_case_latency,
+						wm0.consumption_rate);
+			b.full = rfixed_const(16 * 1000);
+			priority_mark02.full = rfixed_div(a, b);
+		}
+		if (wm0.priority_mark.full > priority_mark02.full)
+			priority_mark02.full = wm0.priority_mark.full;
+		if (rfixed_trunc(priority_mark02) < 0)
+			priority_mark02.full = 0;
+		if (wm0.priority_mark_max.full > priority_mark02.full)
+			priority_mark02.full = wm0.priority_mark_max.full;
+		WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02));
+		WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02));
+		WREG32(D2MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF);
+		WREG32(D2MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF);
+	} else {
+		if (rfixed_trunc(wm1.dbpp) > 64)
+			a.full = rfixed_mul(wm1.dbpp, wm1.num_line_pair);
+		else
+			a.full = wm1.num_line_pair.full;
+		fill_rate.full = rfixed_div(wm1.sclk, a);
+		if (wm1.consumption_rate.full > fill_rate.full) {
+			b.full = wm1.consumption_rate.full - fill_rate.full;
+			b.full = rfixed_mul(b, wm1.active_time);
+			a.full = rfixed_mul(wm1.worst_case_latency,
+						wm1.consumption_rate);
+			a.full = a.full + b.full;
+			b.full = rfixed_const(16 * 1000);
+			priority_mark12.full = rfixed_div(a, b);
+		} else {
+			a.full = rfixed_mul(wm1.worst_case_latency,
+						wm1.consumption_rate);
+			b.full = rfixed_const(16 * 1000);
+			priority_mark12.full = rfixed_div(a, b);
+		}
+		if (wm1.priority_mark.full > priority_mark12.full)
+			priority_mark12.full = wm1.priority_mark.full;
+		if (rfixed_trunc(priority_mark12) < 0)
+			priority_mark12.full = 0;
+		if (wm1.priority_mark_max.full > priority_mark12.full)
+			priority_mark12.full = wm1.priority_mark_max.full;
+		WREG32(D1MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF);
+		WREG32(D1MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF);
+		WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12));
+		WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12));
+	}
+}
 
 /*
  * Indirect registers accessor
diff --git a/drivers/gpu/drm/radeon/rs690r.h b/drivers/gpu/drm/radeon/rs690r.h
new file mode 100644
index 00000000000..c0d9faa2175
--- /dev/null
+++ b/drivers/gpu/drm/radeon/rs690r.h
@@ -0,0 +1,99 @@
+/*
+ * Copyright 2008 Advanced Micro Devices, Inc.
+ * Copyright 2008 Red Hat Inc.
+ * Copyright 2009 Jerome Glisse.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: Dave Airlie
+ *          Alex Deucher
+ *          Jerome Glisse
+ */
+#ifndef RS690R_H
+#define RS690R_H
+
+/* RS690/RS740 registers */
+#define MC_INDEX			0x0078
+#	define MC_INDEX_MASK			0x1FF
+#	define MC_INDEX_WR_EN			(1 << 9)
+#	define MC_INDEX_WR_ACK			0x7F
+#define MC_DATA				0x007C
+#define HDP_FB_LOCATION			0x0134
+#define DC_LB_MEMORY_SPLIT		0x6520
+#define		DC_LB_MEMORY_SPLIT_MASK			0x00000003
+#define		DC_LB_MEMORY_SPLIT_SHIFT		0
+#define		DC_LB_MEMORY_SPLIT_D1HALF_D2HALF	0
+#define		DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q		1
+#define		DC_LB_MEMORY_SPLIT_D1_ONLY		2
+#define		DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q		3
+#define		DC_LB_MEMORY_SPLIT_SHIFT_MODE		(1 << 2)
+#define		DC_LB_DISP1_END_ADR_SHIFT		4
+#define		DC_LB_DISP1_END_ADR_MASK		0x00007FF0
+#define D1MODE_PRIORITY_A_CNT		0x6548
+#define		MODE_PRIORITY_MARK_MASK			0x00007FFF
+#define		MODE_PRIORITY_OFF			(1 << 16)
+#define		MODE_PRIORITY_ALWAYS_ON			(1 << 20)
+#define		MODE_PRIORITY_FORCE_MASK		(1 << 24)
+#define D1MODE_PRIORITY_B_CNT		0x654C
+#define LB_MAX_REQ_OUTSTANDING		0x6D58
+#define		LB_D1_MAX_REQ_OUTSTANDING_MASK		0x0000000F
+#define		LB_D1_MAX_REQ_OUTSTANDING_SHIFT		0
+#define		LB_D2_MAX_REQ_OUTSTANDING_MASK		0x000F0000
+#define		LB_D2_MAX_REQ_OUTSTANDING_SHIFT		16
+#define DCP_CONTROL			0x6C9C
+#define D2MODE_PRIORITY_A_CNT		0x6D48
+#define D2MODE_PRIORITY_B_CNT		0x6D4C
+
+/* MC indirect registers */
+#define MC_STATUS_IDLE				(1 << 0)
+#define MC_MISC_CNTL			0x18
+#define		DISABLE_GTW			(1 << 1)
+#define		GART_INDEX_REG_EN		(1 << 12)
+#define		BLOCK_GFX_D3_EN			(1 << 14)
+#define GART_FEATURE_ID			0x2B
+#define		HANG_EN				(1 << 11)
+#define		TLB_ENABLE			(1 << 18)
+#define		P2P_ENABLE			(1 << 19)
+#define		GTW_LAC_EN			(1 << 25)
+#define		LEVEL2_GART			(0 << 30)
+#define		LEVEL1_GART			(1 << 30)
+#define		PDC_EN				(1 << 31)
+#define GART_BASE			0x2C
+#define GART_CACHE_CNTRL		0x2E
+#	define GART_CACHE_INVALIDATE		(1 << 0)
+#define MC_STATUS			0x90
+#define MCCFG_FB_LOCATION		0x100
+#define		MC_FB_START_MASK		0x0000FFFF
+#define		MC_FB_START_SHIFT		0
+#define		MC_FB_TOP_MASK			0xFFFF0000
+#define		MC_FB_TOP_SHIFT			16
+#define MCCFG_AGP_LOCATION		0x101
+#define		MC_AGP_START_MASK		0x0000FFFF
+#define		MC_AGP_START_SHIFT		0
+#define		MC_AGP_TOP_MASK			0xFFFF0000
+#define		MC_AGP_TOP_SHIFT		16
+#define MCCFG_AGP_BASE			0x102
+#define MCCFG_AGP_BASE_2		0x103
+#define MC_INIT_MISC_LAT_TIMER		0x104
+#define		MC_DISP0R_INIT_LAT_SHIFT	8
+#define		MC_DISP0R_INIT_LAT_MASK		0x00000F00
+#define		MC_DISP1R_INIT_LAT_SHIFT	12
+#define		MC_DISP1R_INIT_LAT_MASK		0x0000F000
+
+#endif
diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c
index 677929ed8ed..4fd411893b9 100644
--- a/drivers/gpu/drm/radeon/rv515.c
+++ b/drivers/gpu/drm/radeon/rv515.c
@@ -27,8 +27,9 @@
  */
 #include <linux/seq_file.h>
 #include "drmP.h"
-#include "radeon_reg.h"
+#include "rv515r.h"
 #include "radeon.h"
+#include "radeon_share.h"
 
 /* rv515 depends on : */
 void r100_hdp_reset(struct radeon_device *rdev);
@@ -100,25 +101,25 @@ int rv515_mc_init(struct radeon_device *rdev)
 	}
 	/* Write VRAM size in case we are limiting it */
 	WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size);
-	tmp = REG_SET(RV515_MC_FB_START, rdev->mc.vram_location >> 16);
+	tmp = REG_SET(MC_FB_START, rdev->mc.vram_location >> 16);
 	WREG32(0x134, tmp);
 	tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1;
-	tmp = REG_SET(RV515_MC_FB_TOP, tmp >> 16);
-	tmp |= REG_SET(RV515_MC_FB_START, rdev->mc.vram_location >> 16);
-	WREG32_MC(RV515_MC_FB_LOCATION, tmp);
-	WREG32(RS690_HDP_FB_LOCATION, rdev->mc.vram_location >> 16);
+	tmp = REG_SET(MC_FB_TOP, tmp >> 16);
+	tmp |= REG_SET(MC_FB_START, rdev->mc.vram_location >> 16);
+	WREG32_MC(MC_FB_LOCATION, tmp);
+	WREG32(HDP_FB_LOCATION, rdev->mc.vram_location >> 16);
 	WREG32(0x310, rdev->mc.vram_location);
 	if (rdev->flags & RADEON_IS_AGP) {
 		tmp = rdev->mc.gtt_location + rdev->mc.gtt_size - 1;
-		tmp = REG_SET(RV515_MC_AGP_TOP, tmp >> 16);
-		tmp |= REG_SET(RV515_MC_AGP_START, rdev->mc.gtt_location >> 16);
-		WREG32_MC(RV515_MC_AGP_LOCATION, tmp);
-		WREG32_MC(RV515_MC_AGP_BASE, rdev->mc.agp_base);
-		WREG32_MC(RV515_MC_AGP_BASE_2, 0);
+		tmp = REG_SET(MC_AGP_TOP, tmp >> 16);
+		tmp |= REG_SET(MC_AGP_START, rdev->mc.gtt_location >> 16);
+		WREG32_MC(MC_AGP_LOCATION, tmp);
+		WREG32_MC(MC_AGP_BASE, rdev->mc.agp_base);
+		WREG32_MC(MC_AGP_BASE_2, 0);
 	} else {
-		WREG32_MC(RV515_MC_AGP_LOCATION, 0x0FFFFFFF);
-		WREG32_MC(RV515_MC_AGP_BASE, 0);
-		WREG32_MC(RV515_MC_AGP_BASE_2, 0);
+		WREG32_MC(MC_AGP_LOCATION, 0x0FFFFFFF);
+		WREG32_MC(MC_AGP_BASE, 0);
+		WREG32_MC(MC_AGP_BASE_2, 0);
 	}
 	return 0;
 }
@@ -136,95 +137,67 @@ void rv515_mc_fini(struct radeon_device *rdev)
  */
 void rv515_ring_start(struct radeon_device *rdev)
 {
-	unsigned gb_tile_config;
 	int r;
 
-	/* Sub pixel 1/12 so we can have 4K rendering according to doc */
-	gb_tile_config = R300_ENABLE_TILING | R300_TILE_SIZE_16;
-	switch (rdev->num_gb_pipes) {
-	case 2:
-		gb_tile_config |= R300_PIPE_COUNT_R300;
-		break;
-	case 3:
-		gb_tile_config |= R300_PIPE_COUNT_R420_3P;
-		break;
-	case 4:
-		gb_tile_config |= R300_PIPE_COUNT_R420;
-		break;
-	case 1:
-	default:
-		gb_tile_config |= R300_PIPE_COUNT_RV350;
-		break;
-	}
-
 	r = radeon_ring_lock(rdev, 64);
 	if (r) {
 		return;
 	}
-	radeon_ring_write(rdev, PACKET0(RADEON_ISYNC_CNTL, 0));
-	radeon_ring_write(rdev,
-			  RADEON_ISYNC_ANY2D_IDLE3D |
-			  RADEON_ISYNC_ANY3D_IDLE2D |
-			  RADEON_ISYNC_WAIT_IDLEGUI |
-			  RADEON_ISYNC_CPSCRATCH_IDLEGUI);
-	radeon_ring_write(rdev, PACKET0(R300_GB_TILE_CONFIG, 0));
-	radeon_ring_write(rdev, gb_tile_config);
-	radeon_ring_write(rdev, PACKET0(RADEON_WAIT_UNTIL, 0));
+	radeon_ring_write(rdev, PACKET0(ISYNC_CNTL, 0));
 	radeon_ring_write(rdev,
-			  RADEON_WAIT_2D_IDLECLEAN |
-			  RADEON_WAIT_3D_IDLECLEAN);
+			  ISYNC_ANY2D_IDLE3D |
+			  ISYNC_ANY3D_IDLE2D |
+			  ISYNC_WAIT_IDLEGUI |
+			  ISYNC_CPSCRATCH_IDLEGUI);
+	radeon_ring_write(rdev, PACKET0(WAIT_UNTIL, 0));
+	radeon_ring_write(rdev, WAIT_2D_IDLECLEAN | WAIT_3D_IDLECLEAN);
 	radeon_ring_write(rdev, PACKET0(0x170C, 0));
 	radeon_ring_write(rdev, 1 << 31);
-	radeon_ring_write(rdev, PACKET0(R300_GB_SELECT, 0));
+	radeon_ring_write(rdev, PACKET0(GB_SELECT, 0));
 	radeon_ring_write(rdev, 0);
-	radeon_ring_write(rdev, PACKET0(R300_GB_ENABLE, 0));
+	radeon_ring_write(rdev, PACKET0(GB_ENABLE, 0));
 	radeon_ring_write(rdev, 0);
 	radeon_ring_write(rdev, PACKET0(0x42C8, 0));
 	radeon_ring_write(rdev, (1 << rdev->num_gb_pipes) - 1);
-	radeon_ring_write(rdev, PACKET0(R500_VAP_INDEX_OFFSET, 0));
+	radeon_ring_write(rdev, PACKET0(VAP_INDEX_OFFSET, 0));
 	radeon_ring_write(rdev, 0);
-	radeon_ring_write(rdev, PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0));
-	radeon_ring_write(rdev, R300_RB3D_DC_FLUSH | R300_RB3D_DC_FREE);
-	radeon_ring_write(rdev, PACKET0(R300_RB3D_ZCACHE_CTLSTAT, 0));
-	radeon_ring_write(rdev, R300_ZC_FLUSH | R300_ZC_FREE);
-	radeon_ring_write(rdev, PACKET0(RADEON_WAIT_UNTIL, 0));
-	radeon_ring_write(rdev,
-			  RADEON_WAIT_2D_IDLECLEAN |
-			  RADEON_WAIT_3D_IDLECLEAN);
-	radeon_ring_write(rdev, PACKET0(R300_GB_AA_CONFIG, 0));
+	radeon_ring_write(rdev, PACKET0(RB3D_DSTCACHE_CTLSTAT, 0));
+	radeon_ring_write(rdev, RB3D_DC_FLUSH | RB3D_DC_FREE);
+	radeon_ring_write(rdev, PACKET0(ZB_ZCACHE_CTLSTAT, 0));
+	radeon_ring_write(rdev, ZC_FLUSH | ZC_FREE);
+	radeon_ring_write(rdev, PACKET0(WAIT_UNTIL, 0));
+	radeon_ring_write(rdev, WAIT_2D_IDLECLEAN | WAIT_3D_IDLECLEAN);
+	radeon_ring_write(rdev, PACKET0(GB_AA_CONFIG, 0));
 	radeon_ring_write(rdev, 0);
-	radeon_ring_write(rdev, PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0));
-	radeon_ring_write(rdev, R300_RB3D_DC_FLUSH | R300_RB3D_DC_FREE);
-	radeon_ring_write(rdev, PACKET0(R300_RB3D_ZCACHE_CTLSTAT, 0));
-	radeon_ring_write(rdev, R300_ZC_FLUSH | R300_ZC_FREE);
-	radeon_ring_write(rdev, PACKET0(R300_GB_MSPOS0, 0));
-	radeon_ring_write(rdev,
-			  ((6 << R300_MS_X0_SHIFT) |
-			   (6 << R300_MS_Y0_SHIFT) |
-			   (6 << R300_MS_X1_SHIFT) |
-			   (6 << R300_MS_Y1_SHIFT) |
-			   (6 << R300_MS_X2_SHIFT) |
-			   (6 << R300_MS_Y2_SHIFT) |
-			   (6 << R300_MSBD0_Y_SHIFT) |
-			   (6 << R300_MSBD0_X_SHIFT)));
-	radeon_ring_write(rdev, PACKET0(R300_GB_MSPOS1, 0));
-	radeon_ring_write(rdev,
-			  ((6 << R300_MS_X3_SHIFT) |
-			   (6 << R300_MS_Y3_SHIFT) |
-			   (6 << R300_MS_X4_SHIFT) |
-			   (6 << R300_MS_Y4_SHIFT) |
-			   (6 << R300_MS_X5_SHIFT) |
-			   (6 << R300_MS_Y5_SHIFT) |
-			   (6 << R300_MSBD1_SHIFT)));
-	radeon_ring_write(rdev, PACKET0(R300_GA_ENHANCE, 0));
-	radeon_ring_write(rdev, R300_GA_DEADLOCK_CNTL | R300_GA_FASTSYNC_CNTL);
-	radeon_ring_write(rdev, PACKET0(R300_GA_POLY_MODE, 0));
+	radeon_ring_write(rdev, PACKET0(RB3D_DSTCACHE_CTLSTAT, 0));
+	radeon_ring_write(rdev, RB3D_DC_FLUSH | RB3D_DC_FREE);
+	radeon_ring_write(rdev, PACKET0(ZB_ZCACHE_CTLSTAT, 0));
+	radeon_ring_write(rdev, ZC_FLUSH | ZC_FREE);
+	radeon_ring_write(rdev, PACKET0(GB_MSPOS0, 0));
 	radeon_ring_write(rdev,
-			  R300_FRONT_PTYPE_TRIANGE | R300_BACK_PTYPE_TRIANGE);
-	radeon_ring_write(rdev, PACKET0(R300_GA_ROUND_MODE, 0));
+			  ((6 << MS_X0_SHIFT) |
+			   (6 << MS_Y0_SHIFT) |
+			   (6 << MS_X1_SHIFT) |
+			   (6 << MS_Y1_SHIFT) |
+			   (6 << MS_X2_SHIFT) |
+			   (6 << MS_Y2_SHIFT) |
+			   (6 << MSBD0_Y_SHIFT) |
+			   (6 << MSBD0_X_SHIFT)));
+	radeon_ring_write(rdev, PACKET0(GB_MSPOS1, 0));
 	radeon_ring_write(rdev,
-			  R300_GEOMETRY_ROUND_NEAREST |
-			  R300_COLOR_ROUND_NEAREST);
+			  ((6 << MS_X3_SHIFT) |
+			   (6 << MS_Y3_SHIFT) |
+			   (6 << MS_X4_SHIFT) |
+			   (6 << MS_Y4_SHIFT) |
+			   (6 << MS_X5_SHIFT) |
+			   (6 << MS_Y5_SHIFT) |
+			   (6 << MSBD1_SHIFT)));
+	radeon_ring_write(rdev, PACKET0(GA_ENHANCE, 0));
+	radeon_ring_write(rdev, GA_DEADLOCK_CNTL | GA_FASTSYNC_CNTL);
+	radeon_ring_write(rdev, PACKET0(GA_POLY_MODE, 0));
+	radeon_ring_write(rdev, FRONT_PTYPE_TRIANGE | BACK_PTYPE_TRIANGE);
+	radeon_ring_write(rdev, PACKET0(GA_ROUND_MODE, 0));
+	radeon_ring_write(rdev, GEOMETRY_ROUND_NEAREST | COLOR_ROUND_NEAREST);
 	radeon_ring_write(rdev, PACKET0(0x20C8, 0));
 	radeon_ring_write(rdev, 0);
 	radeon_ring_unlock_commit(rdev);
@@ -242,8 +215,8 @@ int rv515_mc_wait_for_idle(struct radeon_device *rdev)
 
 	for (i = 0; i < rdev->usec_timeout; i++) {
 		/* read MC_STATUS */
-		tmp = RREG32_MC(RV515_MC_STATUS);
-		if (tmp & RV515_MC_STATUS_IDLE) {
+		tmp = RREG32_MC(MC_STATUS);
+		if (tmp & MC_STATUS_IDLE) {
 			return 0;
 		}
 		DRM_UDELAY(1);
@@ -291,33 +264,33 @@ int rv515_ga_reset(struct radeon_device *rdev)
 	reinit_cp = rdev->cp.ready;
 	rdev->cp.ready = false;
 	for (i = 0; i < rdev->usec_timeout; i++) {
-		WREG32(RADEON_CP_CSQ_MODE, 0);
-		WREG32(RADEON_CP_CSQ_CNTL, 0);
-		WREG32(RADEON_RBBM_SOFT_RESET, 0x32005);
-		(void)RREG32(RADEON_RBBM_SOFT_RESET);
+		WREG32(CP_CSQ_MODE, 0);
+		WREG32(CP_CSQ_CNTL, 0);
+		WREG32(RBBM_SOFT_RESET, 0x32005);
+		(void)RREG32(RBBM_SOFT_RESET);
 		udelay(200);
-		WREG32(RADEON_RBBM_SOFT_RESET, 0);
+		WREG32(RBBM_SOFT_RESET, 0);
 		/* Wait to prevent race in RBBM_STATUS */
 		mdelay(1);
-		tmp = RREG32(RADEON_RBBM_STATUS);
+		tmp = RREG32(RBBM_STATUS);
 		if (tmp & ((1 << 20) | (1 << 26))) {
 			DRM_ERROR("VAP & CP still busy (RBBM_STATUS=0x%08X)\n", tmp);
 			/* GA still busy soft reset it */
 			WREG32(0x429C, 0x200);
-			WREG32(R300_VAP_PVS_STATE_FLUSH_REG, 0);
+			WREG32(VAP_PVS_STATE_FLUSH_REG, 0);
 			WREG32(0x43E0, 0);
 			WREG32(0x43E4, 0);
 			WREG32(0x24AC, 0);
 		}
 		/* Wait to prevent race in RBBM_STATUS */
 		mdelay(1);
-		tmp = RREG32(RADEON_RBBM_STATUS);
+		tmp = RREG32(RBBM_STATUS);
 		if (!(tmp & ((1 << 20) | (1 << 26)))) {
 			break;
 		}
 	}
 	for (i = 0; i < rdev->usec_timeout; i++) {
-		tmp = RREG32(RADEON_RBBM_STATUS);
+		tmp = RREG32(RBBM_STATUS);
 		if (!(tmp & ((1 << 20) | (1 << 26)))) {
 			DRM_INFO("GA reset succeed (RBBM_STATUS=0x%08X)\n",
 				 tmp);
@@ -331,7 +304,7 @@ int rv515_ga_reset(struct radeon_device *rdev)
 		}
 		DRM_UDELAY(1);
 	}
-	tmp = RREG32(RADEON_RBBM_STATUS);
+	tmp = RREG32(RBBM_STATUS);
 	DRM_ERROR("Failed to reset GA ! (RBBM_STATUS=0x%08X)\n", tmp);
 	return -1;
 }
@@ -341,7 +314,7 @@ int rv515_gpu_reset(struct radeon_device *rdev)
 	uint32_t status;
 
 	/* reset order likely matter */
-	status = RREG32(RADEON_RBBM_STATUS);
+	status = RREG32(RBBM_STATUS);
 	/* reset HDP */
 	r100_hdp_reset(rdev);
 	/* reset rb2d */
@@ -353,12 +326,12 @@ int rv515_gpu_reset(struct radeon_device *rdev)
 		rv515_ga_reset(rdev);
 	}
 	/* reset CP */
-	status = RREG32(RADEON_RBBM_STATUS);
+	status = RREG32(RBBM_STATUS);
 	if (status & (1 << 16)) {
 		r100_cp_reset(rdev);
 	}
 	/* Check if GPU is idle */
-	status = RREG32(RADEON_RBBM_STATUS);
+	status = RREG32(RBBM_STATUS);
 	if (status & (1 << 31)) {
 		DRM_ERROR("Failed to reset GPU (RBBM_STATUS=0x%08X)\n", status);
 		return -1;
@@ -377,8 +350,7 @@ static void rv515_vram_get_type(struct radeon_device *rdev)
 
 	rdev->mc.vram_width = 128;
 	rdev->mc.vram_is_ddr = true;
-	tmp = RREG32_MC(RV515_MC_CNTL);
-	tmp &= RV515_MEM_NUM_CHANNELS_MASK;
+	tmp = RREG32_MC(RV515_MC_CNTL) & MEM_NUM_CHANNELS_MASK;
 	switch (tmp) {
 	case 0:
 		rdev->mc.vram_width = 64;
@@ -394,9 +366,19 @@ static void rv515_vram_get_type(struct radeon_device *rdev)
 
 void rv515_vram_info(struct radeon_device *rdev)
 {
+	fixed20_12 a;
+
 	rv515_vram_get_type(rdev);
-	
-	r100_vram_init_sizes(rdev);
+	rdev->mc.vram_size = RREG32(CONFIG_MEMSIZE);
+
+	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
+	rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0);
+	/* FIXME: we should enforce default clock in case GPU is not in
+	 * default setup
+	 */
+	a.full = rfixed_const(100);
+	rdev->pm.sclk.full = rfixed_const(rdev->clock.default_sclk);
+	rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a);
 }
 
 
@@ -407,35 +389,35 @@ uint32_t rv515_mc_rreg(struct radeon_device *rdev, uint32_t reg)
 {
 	uint32_t r;
 
-	WREG32(R520_MC_IND_INDEX, 0x7f0000 | (reg & 0xffff));
-	r = RREG32(R520_MC_IND_DATA);
-	WREG32(R520_MC_IND_INDEX, 0);
+	WREG32(MC_IND_INDEX, 0x7f0000 | (reg & 0xffff));
+	r = RREG32(MC_IND_DATA);
+	WREG32(MC_IND_INDEX, 0);
 	return r;
 }
 
 void rv515_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
 {
-	WREG32(R520_MC_IND_INDEX, 0xff0000 | ((reg) & 0xffff));
-	WREG32(R520_MC_IND_DATA, (v));
-	WREG32(R520_MC_IND_INDEX, 0);
+	WREG32(MC_IND_INDEX, 0xff0000 | ((reg) & 0xffff));
+	WREG32(MC_IND_DATA, (v));
+	WREG32(MC_IND_INDEX, 0);
 }
 
 uint32_t rv515_pcie_rreg(struct radeon_device *rdev, uint32_t reg)
 {
 	uint32_t r;
 
-	WREG32(RADEON_PCIE_INDEX, ((reg) & 0x7ff));
-	(void)RREG32(RADEON_PCIE_INDEX);
-	r = RREG32(RADEON_PCIE_DATA);
+	WREG32(PCIE_INDEX, ((reg) & 0x7ff));
+	(void)RREG32(PCIE_INDEX);
+	r = RREG32(PCIE_DATA);
 	return r;
 }
 
 void rv515_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
 {
-	WREG32(RADEON_PCIE_INDEX, ((reg) & 0x7ff));
-	(void)RREG32(RADEON_PCIE_INDEX);
-	WREG32(RADEON_PCIE_DATA, (v));
-	(void)RREG32(RADEON_PCIE_DATA);
+	WREG32(PCIE_INDEX, ((reg) & 0x7ff));
+	(void)RREG32(PCIE_INDEX);
+	WREG32(PCIE_DATA, (v));
+	(void)RREG32(PCIE_DATA);
 }
 
 
@@ -450,13 +432,13 @@ static int rv515_debugfs_pipes_info(struct seq_file *m, void *data)
 	struct radeon_device *rdev = dev->dev_private;
 	uint32_t tmp;
 
-	tmp = RREG32(R400_GB_PIPE_SELECT);
+	tmp = RREG32(GB_PIPE_SELECT);
 	seq_printf(m, "GB_PIPE_SELECT 0x%08x\n", tmp);
-	tmp = RREG32(R500_SU_REG_DEST);
+	tmp = RREG32(SU_REG_DEST);
 	seq_printf(m, "SU_REG_DEST 0x%08x\n", tmp);
-	tmp = RREG32(R300_GB_TILE_CONFIG);
+	tmp = RREG32(GB_TILE_CONFIG);
 	seq_printf(m, "GB_TILE_CONFIG 0x%08x\n", tmp);
-	tmp = RREG32(R300_DST_PIPE_CONFIG);
+	tmp = RREG32(DST_PIPE_CONFIG);
 	seq_printf(m, "DST_PIPE_CONFIG 0x%08x\n", tmp);
 	return 0;
 }
@@ -571,3 +553,551 @@ int rv515_init(struct radeon_device *rdev)
 	rdev->config.r300.reg_safe_bm_size = ARRAY_SIZE(r500_reg_safe_bm);
 	return 0;
 }
+
+void atom_rv515_force_tv_scaler(struct radeon_device *rdev)
+{
+
+	WREG32(0x659C, 0x0);
+	WREG32(0x6594, 0x705);
+	WREG32(0x65A4, 0x10001);
+	WREG32(0x65D8, 0x0);
+	WREG32(0x65B0, 0x0);
+	WREG32(0x65C0, 0x0);
+	WREG32(0x65D4, 0x0);
+	WREG32(0x6578, 0x0);
+	WREG32(0x657C, 0x841880A8);
+	WREG32(0x6578, 0x1);
+	WREG32(0x657C, 0x84208680);
+	WREG32(0x6578, 0x2);
+	WREG32(0x657C, 0xBFF880B0);
+	WREG32(0x6578, 0x100);
+	WREG32(0x657C, 0x83D88088);
+	WREG32(0x6578, 0x101);
+	WREG32(0x657C, 0x84608680);
+	WREG32(0x6578, 0x102);
+	WREG32(0x657C, 0xBFF080D0);
+	WREG32(0x6578, 0x200);
+	WREG32(0x657C, 0x83988068);
+	WREG32(0x6578, 0x201);
+	WREG32(0x657C, 0x84A08680);
+	WREG32(0x6578, 0x202);
+	WREG32(0x657C, 0xBFF080F8);
+	WREG32(0x6578, 0x300);
+	WREG32(0x657C, 0x83588058);
+	WREG32(0x6578, 0x301);
+	WREG32(0x657C, 0x84E08660);
+	WREG32(0x6578, 0x302);
+	WREG32(0x657C, 0xBFF88120);
+	WREG32(0x6578, 0x400);
+	WREG32(0x657C, 0x83188040);
+	WREG32(0x6578, 0x401);
+	WREG32(0x657C, 0x85008660);
+	WREG32(0x6578, 0x402);
+	WREG32(0x657C, 0xBFF88150);
+	WREG32(0x6578, 0x500);
+	WREG32(0x657C, 0x82D88030);
+	WREG32(0x6578, 0x501);
+	WREG32(0x657C, 0x85408640);
+	WREG32(0x6578, 0x502);
+	WREG32(0x657C, 0xBFF88180);
+	WREG32(0x6578, 0x600);
+	WREG32(0x657C, 0x82A08018);
+	WREG32(0x6578, 0x601);
+	WREG32(0x657C, 0x85808620);
+	WREG32(0x6578, 0x602);
+	WREG32(0x657C, 0xBFF081B8);
+	WREG32(0x6578, 0x700);
+	WREG32(0x657C, 0x82608010);
+	WREG32(0x6578, 0x701);
+	WREG32(0x657C, 0x85A08600);
+	WREG32(0x6578, 0x702);
+	WREG32(0x657C, 0x800081F0);
+	WREG32(0x6578, 0x800);
+	WREG32(0x657C, 0x8228BFF8);
+	WREG32(0x6578, 0x801);
+	WREG32(0x657C, 0x85E085E0);
+	WREG32(0x6578, 0x802);
+	WREG32(0x657C, 0xBFF88228);
+	WREG32(0x6578, 0x10000);
+	WREG32(0x657C, 0x82A8BF00);
+	WREG32(0x6578, 0x10001);
+	WREG32(0x657C, 0x82A08CC0);
+	WREG32(0x6578, 0x10002);
+	WREG32(0x657C, 0x8008BEF8);
+	WREG32(0x6578, 0x10100);
+	WREG32(0x657C, 0x81F0BF28);
+	WREG32(0x6578, 0x10101);
+	WREG32(0x657C, 0x83608CA0);
+	WREG32(0x6578, 0x10102);
+	WREG32(0x657C, 0x8018BED0);
+	WREG32(0x6578, 0x10200);
+	WREG32(0x657C, 0x8148BF38);
+	WREG32(0x6578, 0x10201);
+	WREG32(0x657C, 0x84408C80);
+	WREG32(0x6578, 0x10202);
+	WREG32(0x657C, 0x8008BEB8);
+	WREG32(0x6578, 0x10300);
+	WREG32(0x657C, 0x80B0BF78);
+	WREG32(0x6578, 0x10301);
+	WREG32(0x657C, 0x85008C20);
+	WREG32(0x6578, 0x10302);
+	WREG32(0x657C, 0x8020BEA0);
+	WREG32(0x6578, 0x10400);
+	WREG32(0x657C, 0x8028BF90);
+	WREG32(0x6578, 0x10401);
+	WREG32(0x657C, 0x85E08BC0);
+	WREG32(0x6578, 0x10402);
+	WREG32(0x657C, 0x8018BE90);
+	WREG32(0x6578, 0x10500);
+	WREG32(0x657C, 0xBFB8BFB0);
+	WREG32(0x6578, 0x10501);
+	WREG32(0x657C, 0x86C08B40);
+	WREG32(0x6578, 0x10502);
+	WREG32(0x657C, 0x8010BE90);
+	WREG32(0x6578, 0x10600);
+	WREG32(0x657C, 0xBF58BFC8);
+	WREG32(0x6578, 0x10601);
+	WREG32(0x657C, 0x87A08AA0);
+	WREG32(0x6578, 0x10602);
+	WREG32(0x657C, 0x8010BE98);
+	WREG32(0x6578, 0x10700);
+	WREG32(0x657C, 0xBF10BFF0);
+	WREG32(0x6578, 0x10701);
+	WREG32(0x657C, 0x886089E0);
+	WREG32(0x6578, 0x10702);
+	WREG32(0x657C, 0x8018BEB0);
+	WREG32(0x6578, 0x10800);
+	WREG32(0x657C, 0xBED8BFE8);
+	WREG32(0x6578, 0x10801);
+	WREG32(0x657C, 0x89408940);
+	WREG32(0x6578, 0x10802);
+	WREG32(0x657C, 0xBFE8BED8);
+	WREG32(0x6578, 0x20000);
+	WREG32(0x657C, 0x80008000);
+	WREG32(0x6578, 0x20001);
+	WREG32(0x657C, 0x90008000);
+	WREG32(0x6578, 0x20002);
+	WREG32(0x657C, 0x80008000);
+	WREG32(0x6578, 0x20003);
+	WREG32(0x657C, 0x80008000);
+	WREG32(0x6578, 0x20100);
+	WREG32(0x657C, 0x80108000);
+	WREG32(0x6578, 0x20101);
+	WREG32(0x657C, 0x8FE0BF70);
+	WREG32(0x6578, 0x20102);
+	WREG32(0x657C, 0xBFE880C0);
+	WREG32(0x6578, 0x20103);
+	WREG32(0x657C, 0x80008000);
+	WREG32(0x6578, 0x20200);
+	WREG32(0x657C, 0x8018BFF8);
+	WREG32(0x6578, 0x20201);
+	WREG32(0x657C, 0x8F80BF08);
+	WREG32(0x6578, 0x20202);
+	WREG32(0x657C, 0xBFD081A0);
+	WREG32(0x6578, 0x20203);
+	WREG32(0x657C, 0xBFF88000);
+	WREG32(0x6578, 0x20300);
+	WREG32(0x657C, 0x80188000);
+	WREG32(0x6578, 0x20301);
+	WREG32(0x657C, 0x8EE0BEC0);
+	WREG32(0x6578, 0x20302);
+	WREG32(0x657C, 0xBFB082A0);
+	WREG32(0x6578, 0x20303);
+	WREG32(0x657C, 0x80008000);
+	WREG32(0x6578, 0x20400);
+	WREG32(0x657C, 0x80188000);
+	WREG32(0x6578, 0x20401);
+	WREG32(0x657C, 0x8E00BEA0);
+	WREG32(0x6578, 0x20402);
+	WREG32(0x657C, 0xBF8883C0);
+	WREG32(0x6578, 0x20403);
+	WREG32(0x657C, 0x80008000);
+	WREG32(0x6578, 0x20500);
+	WREG32(0x657C, 0x80188000);
+	WREG32(0x6578, 0x20501);
+	WREG32(0x657C, 0x8D00BE90);
+	WREG32(0x6578, 0x20502);
+	WREG32(0x657C, 0xBF588500);
+	WREG32(0x6578, 0x20503);
+	WREG32(0x657C, 0x80008008);
+	WREG32(0x6578, 0x20600);
+	WREG32(0x657C, 0x80188000);
+	WREG32(0x6578, 0x20601);
+	WREG32(0x657C, 0x8BC0BE98);
+	WREG32(0x6578, 0x20602);
+	WREG32(0x657C, 0xBF308660);
+	WREG32(0x6578, 0x20603);
+	WREG32(0x657C, 0x80008008);
+	WREG32(0x6578, 0x20700);
+	WREG32(0x657C, 0x80108000);
+	WREG32(0x6578, 0x20701);
+	WREG32(0x657C, 0x8A80BEB0);
+	WREG32(0x6578, 0x20702);
+	WREG32(0x657C, 0xBF0087C0);
+	WREG32(0x6578, 0x20703);
+	WREG32(0x657C, 0x80008008);
+	WREG32(0x6578, 0x20800);
+	WREG32(0x657C, 0x80108000);
+	WREG32(0x6578, 0x20801);
+	WREG32(0x657C, 0x8920BED0);
+	WREG32(0x6578, 0x20802);
+	WREG32(0x657C, 0xBED08920);
+	WREG32(0x6578, 0x20803);
+	WREG32(0x657C, 0x80008010);
+	WREG32(0x6578, 0x30000);
+	WREG32(0x657C, 0x90008000);
+	WREG32(0x6578, 0x30001);
+	WREG32(0x657C, 0x80008000);
+	WREG32(0x6578, 0x30100);
+	WREG32(0x657C, 0x8FE0BF90);
+	WREG32(0x6578, 0x30101);
+	WREG32(0x657C, 0xBFF880A0);
+	WREG32(0x6578, 0x30200);
+	WREG32(0x657C, 0x8F60BF40);
+	WREG32(0x6578, 0x30201);
+	WREG32(0x657C, 0xBFE88180);
+	WREG32(0x6578, 0x30300);
+	WREG32(0x657C, 0x8EC0BF00);
+	WREG32(0x6578, 0x30301);
+	WREG32(0x657C, 0xBFC88280);
+	WREG32(0x6578, 0x30400);
+	WREG32(0x657C, 0x8DE0BEE0);
+	WREG32(0x6578, 0x30401);
+	WREG32(0x657C, 0xBFA083A0);
+	WREG32(0x6578, 0x30500);
+	WREG32(0x657C, 0x8CE0BED0);
+	WREG32(0x6578, 0x30501);
+	WREG32(0x657C, 0xBF7884E0);
+	WREG32(0x6578, 0x30600);
+	WREG32(0x657C, 0x8BA0BED8);
+	WREG32(0x6578, 0x30601);
+	WREG32(0x657C, 0xBF508640);
+	WREG32(0x6578, 0x30700);
+	WREG32(0x657C, 0x8A60BEE8);
+	WREG32(0x6578, 0x30701);
+	WREG32(0x657C, 0xBF2087A0);
+	WREG32(0x6578, 0x30800);
+	WREG32(0x657C, 0x8900BF00);
+	WREG32(0x6578, 0x30801);
+	WREG32(0x657C, 0xBF008900);
+}
+
+struct rv515_watermark {
+	u32        lb_request_fifo_depth;
+	fixed20_12 num_line_pair;
+	fixed20_12 estimated_width;
+	fixed20_12 worst_case_latency;
+	fixed20_12 consumption_rate;
+	fixed20_12 active_time;
+	fixed20_12 dbpp;
+	fixed20_12 priority_mark_max;
+	fixed20_12 priority_mark;
+	fixed20_12 sclk;
+};
+
+void rv515_crtc_bandwidth_compute(struct radeon_device *rdev,
+				  struct radeon_crtc *crtc,
+				  struct rv515_watermark *wm)
+{
+	struct drm_display_mode *mode = &crtc->base.mode;
+	fixed20_12 a, b, c;
+	fixed20_12 pclk, request_fifo_depth, tolerable_latency, estimated_width;
+	fixed20_12 consumption_time, line_time, chunk_time, read_delay_latency;
+
+	if (!crtc->base.enabled) {
+		/* FIXME: wouldn't it better to set priority mark to maximum */
+		wm->lb_request_fifo_depth = 4;
+		return;
+	}
+
+	if (crtc->vsc.full > rfixed_const(2))
+		wm->num_line_pair.full = rfixed_const(2);
+	else
+		wm->num_line_pair.full = rfixed_const(1);
+
+	b.full = rfixed_const(mode->crtc_hdisplay);
+	c.full = rfixed_const(256);
+	a.full = rfixed_mul(wm->num_line_pair, b);
+	request_fifo_depth.full = rfixed_div(a, c);
+	if (a.full < rfixed_const(4)) {
+		wm->lb_request_fifo_depth = 4;
+	} else {
+		wm->lb_request_fifo_depth = rfixed_trunc(request_fifo_depth);
+	}
+
+	/* Determine consumption rate
+	 *  pclk = pixel clock period(ns) = 1000 / (mode.clock / 1000)
+	 *  vtaps = number of vertical taps,
+	 *  vsc = vertical scaling ratio, defined as source/destination
+	 *  hsc = horizontal scaling ration, defined as source/destination
+	 */
+	a.full = rfixed_const(mode->clock);
+	b.full = rfixed_const(1000);
+	a.full = rfixed_div(a, b);
+	pclk.full = rfixed_div(b, a);
+	if (crtc->rmx_type != RMX_OFF) {
+		b.full = rfixed_const(2);
+		if (crtc->vsc.full > b.full)
+			b.full = crtc->vsc.full;
+		b.full = rfixed_mul(b, crtc->hsc);
+		c.full = rfixed_const(2);
+		b.full = rfixed_div(b, c);
+		consumption_time.full = rfixed_div(pclk, b);
+	} else {
+		consumption_time.full = pclk.full;
+	}
+	a.full = rfixed_const(1);
+	wm->consumption_rate.full = rfixed_div(a, consumption_time);
+
+
+	/* Determine line time
+	 *  LineTime = total time for one line of displayhtotal
+	 *  LineTime = total number of horizontal pixels
+	 *  pclk = pixel clock period(ns)
+	 */
+	a.full = rfixed_const(crtc->base.mode.crtc_htotal);
+	line_time.full = rfixed_mul(a, pclk);
+
+	/* Determine active time
+	 *  ActiveTime = time of active region of display within one line,
+	 *  hactive = total number of horizontal active pixels
+	 *  htotal = total number of horizontal pixels
+	 */
+	a.full = rfixed_const(crtc->base.mode.crtc_htotal);
+	b.full = rfixed_const(crtc->base.mode.crtc_hdisplay);
+	wm->active_time.full = rfixed_mul(line_time, b);
+	wm->active_time.full = rfixed_div(wm->active_time, a);
+
+	/* Determine chunk time
+	 * ChunkTime = the time it takes the DCP to send one chunk of data
+	 * to the LB which consists of pipeline delay and inter chunk gap
+	 * sclk = system clock(Mhz)
+	 */
+	a.full = rfixed_const(600 * 1000);
+	chunk_time.full = rfixed_div(a, rdev->pm.sclk);
+	read_delay_latency.full = rfixed_const(1000);
+
+	/* Determine the worst case latency
+	 * NumLinePair = Number of line pairs to request(1=2 lines, 2=4 lines)
+	 * WorstCaseLatency = worst case time from urgent to when the MC starts
+	 *                    to return data
+	 * READ_DELAY_IDLE_MAX = constant of 1us
+	 * ChunkTime = time it takes the DCP to send one chunk of data to the LB
+	 *             which consists of pipeline delay and inter chunk gap
+	 */
+	if (rfixed_trunc(wm->num_line_pair) > 1) {
+		a.full = rfixed_const(3);
+		wm->worst_case_latency.full = rfixed_mul(a, chunk_time);
+		wm->worst_case_latency.full += read_delay_latency.full;
+	} else {
+		wm->worst_case_latency.full = chunk_time.full + read_delay_latency.full;
+	}
+
+	/* Determine the tolerable latency
+	 * TolerableLatency = Any given request has only 1 line time
+	 *                    for the data to be returned
+	 * LBRequestFifoDepth = Number of chunk requests the LB can
+	 *                      put into the request FIFO for a display
+	 *  LineTime = total time for one line of display
+	 *  ChunkTime = the time it takes the DCP to send one chunk
+	 *              of data to the LB which consists of
+	 *  pipeline delay and inter chunk gap
+	 */
+	if ((2+wm->lb_request_fifo_depth) >= rfixed_trunc(request_fifo_depth)) {
+		tolerable_latency.full = line_time.full;
+	} else {
+		tolerable_latency.full = rfixed_const(wm->lb_request_fifo_depth - 2);
+		tolerable_latency.full = request_fifo_depth.full - tolerable_latency.full;
+		tolerable_latency.full = rfixed_mul(tolerable_latency, chunk_time);
+		tolerable_latency.full = line_time.full - tolerable_latency.full;
+	}
+	/* We assume worst case 32bits (4 bytes) */
+	wm->dbpp.full = rfixed_const(2 * 16);
+
+	/* Determine the maximum priority mark
+	 *  width = viewport width in pixels
+	 */
+	a.full = rfixed_const(16);
+	wm->priority_mark_max.full = rfixed_const(crtc->base.mode.crtc_hdisplay);
+	wm->priority_mark_max.full = rfixed_div(wm->priority_mark_max, a);
+
+	/* Determine estimated width */
+	estimated_width.full = tolerable_latency.full - wm->worst_case_latency.full;
+	estimated_width.full = rfixed_div(estimated_width, consumption_time);
+	if (rfixed_trunc(estimated_width) > crtc->base.mode.crtc_hdisplay) {
+		wm->priority_mark.full = rfixed_const(10);
+	} else {
+		a.full = rfixed_const(16);
+		wm->priority_mark.full = rfixed_div(estimated_width, a);
+		wm->priority_mark.full = wm->priority_mark_max.full - wm->priority_mark.full;
+	}
+}
+
+void rv515_bandwidth_avivo_update(struct radeon_device *rdev)
+{
+	struct drm_display_mode *mode0 = NULL;
+	struct drm_display_mode *mode1 = NULL;
+	struct rv515_watermark wm0;
+	struct rv515_watermark wm1;
+	u32 tmp;
+	fixed20_12 priority_mark02, priority_mark12, fill_rate;
+	fixed20_12 a, b;
+
+	if (rdev->mode_info.crtcs[0]->base.enabled)
+		mode0 = &rdev->mode_info.crtcs[0]->base.mode;
+	if (rdev->mode_info.crtcs[1]->base.enabled)
+		mode1 = &rdev->mode_info.crtcs[1]->base.mode;
+	rs690_line_buffer_adjust(rdev, mode0, mode1);
+
+	rv515_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[0], &wm0);
+	rv515_crtc_bandwidth_compute(rdev, rdev->mode_info.crtcs[1], &wm1);
+
+	tmp = wm0.lb_request_fifo_depth;
+	tmp |= wm1.lb_request_fifo_depth << 16;
+	WREG32(LB_MAX_REQ_OUTSTANDING, tmp);
+
+	if (mode0 && mode1) {
+		if (rfixed_trunc(wm0.dbpp) > 64)
+			a.full = rfixed_div(wm0.dbpp, wm0.num_line_pair);
+		else
+			a.full = wm0.num_line_pair.full;
+		if (rfixed_trunc(wm1.dbpp) > 64)
+			b.full = rfixed_div(wm1.dbpp, wm1.num_line_pair);
+		else
+			b.full = wm1.num_line_pair.full;
+		a.full += b.full;
+		fill_rate.full = rfixed_div(wm0.sclk, a);
+		if (wm0.consumption_rate.full > fill_rate.full) {
+			b.full = wm0.consumption_rate.full - fill_rate.full;
+			b.full = rfixed_mul(b, wm0.active_time);
+			a.full = rfixed_const(16);
+			b.full = rfixed_div(b, a);
+			a.full = rfixed_mul(wm0.worst_case_latency,
+						wm0.consumption_rate);
+			priority_mark02.full = a.full + b.full;
+		} else {
+			a.full = rfixed_mul(wm0.worst_case_latency,
+						wm0.consumption_rate);
+			b.full = rfixed_const(16 * 1000);
+			priority_mark02.full = rfixed_div(a, b);
+		}
+		if (wm1.consumption_rate.full > fill_rate.full) {
+			b.full = wm1.consumption_rate.full - fill_rate.full;
+			b.full = rfixed_mul(b, wm1.active_time);
+			a.full = rfixed_const(16);
+			b.full = rfixed_div(b, a);
+			a.full = rfixed_mul(wm1.worst_case_latency,
+						wm1.consumption_rate);
+			priority_mark12.full = a.full + b.full;
+		} else {
+			a.full = rfixed_mul(wm1.worst_case_latency,
+						wm1.consumption_rate);
+			b.full = rfixed_const(16 * 1000);
+			priority_mark12.full = rfixed_div(a, b);
+		}
+		if (wm0.priority_mark.full > priority_mark02.full)
+			priority_mark02.full = wm0.priority_mark.full;
+		if (rfixed_trunc(priority_mark02) < 0)
+			priority_mark02.full = 0;
+		if (wm0.priority_mark_max.full > priority_mark02.full)
+			priority_mark02.full = wm0.priority_mark_max.full;
+		if (wm1.priority_mark.full > priority_mark12.full)
+			priority_mark12.full = wm1.priority_mark.full;
+		if (rfixed_trunc(priority_mark12) < 0)
+			priority_mark12.full = 0;
+		if (wm1.priority_mark_max.full > priority_mark12.full)
+			priority_mark12.full = wm1.priority_mark_max.full;
+		WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02));
+		WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02));
+		WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12));
+		WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12));
+	} else if (mode0) {
+		if (rfixed_trunc(wm0.dbpp) > 64)
+			a.full = rfixed_div(wm0.dbpp, wm0.num_line_pair);
+		else
+			a.full = wm0.num_line_pair.full;
+		fill_rate.full = rfixed_div(wm0.sclk, a);
+		if (wm0.consumption_rate.full > fill_rate.full) {
+			b.full = wm0.consumption_rate.full - fill_rate.full;
+			b.full = rfixed_mul(b, wm0.active_time);
+			a.full = rfixed_const(16);
+			b.full = rfixed_div(b, a);
+			a.full = rfixed_mul(wm0.worst_case_latency,
+						wm0.consumption_rate);
+			priority_mark02.full = a.full + b.full;
+		} else {
+			a.full = rfixed_mul(wm0.worst_case_latency,
+						wm0.consumption_rate);
+			b.full = rfixed_const(16);
+			priority_mark02.full = rfixed_div(a, b);
+		}
+		if (wm0.priority_mark.full > priority_mark02.full)
+			priority_mark02.full = wm0.priority_mark.full;
+		if (rfixed_trunc(priority_mark02) < 0)
+			priority_mark02.full = 0;
+		if (wm0.priority_mark_max.full > priority_mark02.full)
+			priority_mark02.full = wm0.priority_mark_max.full;
+		WREG32(D1MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark02));
+		WREG32(D1MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark02));
+		WREG32(D2MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF);
+		WREG32(D2MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF);
+	} else {
+		if (rfixed_trunc(wm1.dbpp) > 64)
+			a.full = rfixed_div(wm1.dbpp, wm1.num_line_pair);
+		else
+			a.full = wm1.num_line_pair.full;
+		fill_rate.full = rfixed_div(wm1.sclk, a);
+		if (wm1.consumption_rate.full > fill_rate.full) {
+			b.full = wm1.consumption_rate.full - fill_rate.full;
+			b.full = rfixed_mul(b, wm1.active_time);
+			a.full = rfixed_const(16);
+			b.full = rfixed_div(b, a);
+			a.full = rfixed_mul(wm1.worst_case_latency,
+						wm1.consumption_rate);
+			priority_mark12.full = a.full + b.full;
+		} else {
+			a.full = rfixed_mul(wm1.worst_case_latency,
+						wm1.consumption_rate);
+			b.full = rfixed_const(16 * 1000);
+			priority_mark12.full = rfixed_div(a, b);
+		}
+		if (wm1.priority_mark.full > priority_mark12.full)
+			priority_mark12.full = wm1.priority_mark.full;
+		if (rfixed_trunc(priority_mark12) < 0)
+			priority_mark12.full = 0;
+		if (wm1.priority_mark_max.full > priority_mark12.full)
+			priority_mark12.full = wm1.priority_mark_max.full;
+		WREG32(D1MODE_PRIORITY_A_CNT, MODE_PRIORITY_OFF);
+		WREG32(D1MODE_PRIORITY_B_CNT, MODE_PRIORITY_OFF);
+		WREG32(D2MODE_PRIORITY_A_CNT, rfixed_trunc(priority_mark12));
+		WREG32(D2MODE_PRIORITY_B_CNT, rfixed_trunc(priority_mark12));
+	}
+}
+
+void rv515_bandwidth_update(struct radeon_device *rdev)
+{
+	uint32_t tmp;
+	struct drm_display_mode *mode0 = NULL;
+	struct drm_display_mode *mode1 = NULL;
+
+	if (rdev->mode_info.crtcs[0]->base.enabled)
+		mode0 = &rdev->mode_info.crtcs[0]->base.mode;
+	if (rdev->mode_info.crtcs[1]->base.enabled)
+		mode1 = &rdev->mode_info.crtcs[1]->base.mode;
+	/*
+	 * Set display0/1 priority up in the memory controller for
+	 * modes if the user specifies HIGH for displaypriority
+	 * option.
+	 */
+	if (rdev->disp_priority == 2) {
+		tmp = RREG32_MC(MC_MISC_LAT_TIMER);
+		tmp &= ~MC_DISP1R_INIT_LAT_MASK;
+		tmp &= ~MC_DISP0R_INIT_LAT_MASK;
+		if (mode1)
+			tmp |= (1 << MC_DISP1R_INIT_LAT_SHIFT);
+		if (mode0)
+			tmp |= (1 << MC_DISP0R_INIT_LAT_SHIFT);
+		WREG32_MC(MC_MISC_LAT_TIMER, tmp);
+	}
+	rv515_bandwidth_avivo_update(rdev);
+}
diff --git a/drivers/gpu/drm/radeon/rv515r.h b/drivers/gpu/drm/radeon/rv515r.h
new file mode 100644
index 00000000000..f3cf8403990
--- /dev/null
+++ b/drivers/gpu/drm/radeon/rv515r.h
@@ -0,0 +1,170 @@
+/*
+ * Copyright 2008 Advanced Micro Devices, Inc.
+ * Copyright 2008 Red Hat Inc.
+ * Copyright 2009 Jerome Glisse.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: Dave Airlie
+ *          Alex Deucher
+ *          Jerome Glisse
+ */
+#ifndef RV515R_H
+#define RV515R_H
+
+/* RV515 registers */
+#define PCIE_INDEX			0x0030
+#define PCIE_DATA			0x0034
+#define	MC_IND_INDEX			0x0070
+#define		MC_IND_WR_EN				(1 << 24)
+#define	MC_IND_DATA			0x0074
+#define	RBBM_SOFT_RESET			0x00F0
+#define	CONFIG_MEMSIZE			0x00F8
+#define HDP_FB_LOCATION			0x0134
+#define	CP_CSQ_CNTL			0x0740
+#define	CP_CSQ_MODE			0x0744
+#define	CP_CSQ_ADDR			0x07F0
+#define	CP_CSQ_DATA			0x07F4
+#define	CP_CSQ_STAT			0x07F8
+#define	CP_CSQ2_STAT			0x07FC
+#define	RBBM_STATUS			0x0E40
+#define	DST_PIPE_CONFIG			0x170C
+#define	WAIT_UNTIL			0x1720
+#define		WAIT_2D_IDLE				(1 << 14)
+#define		WAIT_3D_IDLE				(1 << 15)
+#define		WAIT_2D_IDLECLEAN			(1 << 16)
+#define		WAIT_3D_IDLECLEAN			(1 << 17)
+#define	ISYNC_CNTL			0x1724
+#define		ISYNC_ANY2D_IDLE3D			(1 << 0)
+#define		ISYNC_ANY3D_IDLE2D			(1 << 1)
+#define		ISYNC_TRIG2D_IDLE3D			(1 << 2)
+#define		ISYNC_TRIG3D_IDLE2D			(1 << 3)
+#define		ISYNC_WAIT_IDLEGUI			(1 << 4)
+#define		ISYNC_CPSCRATCH_IDLEGUI			(1 << 5)
+#define	VAP_INDEX_OFFSET		0x208C
+#define	VAP_PVS_STATE_FLUSH_REG		0x2284
+#define	GB_ENABLE			0x4008
+#define	GB_MSPOS0			0x4010
+#define		MS_X0_SHIFT				0
+#define		MS_Y0_SHIFT				4
+#define		MS_X1_SHIFT				8
+#define		MS_Y1_SHIFT				12
+#define		MS_X2_SHIFT				16
+#define		MS_Y2_SHIFT				20
+#define		MSBD0_Y_SHIFT				24
+#define		MSBD0_X_SHIFT				28
+#define	GB_MSPOS1			0x4014
+#define		MS_X3_SHIFT				0
+#define		MS_Y3_SHIFT				4
+#define		MS_X4_SHIFT				8
+#define		MS_Y4_SHIFT				12
+#define		MS_X5_SHIFT				16
+#define		MS_Y5_SHIFT				20
+#define		MSBD1_SHIFT				24
+#define GB_TILE_CONFIG			0x4018
+#define		ENABLE_TILING				(1 << 0)
+#define		PIPE_COUNT_MASK				0x0000000E
+#define		PIPE_COUNT_SHIFT			1
+#define		TILE_SIZE_8				(0 << 4)
+#define		TILE_SIZE_16				(1 << 4)
+#define		TILE_SIZE_32				(2 << 4)
+#define		SUBPIXEL_1_12				(0 << 16)
+#define		SUBPIXEL_1_16				(1 << 16)
+#define	GB_SELECT			0x401C
+#define	GB_AA_CONFIG			0x4020
+#define	GB_PIPE_SELECT			0x402C
+#define	GA_ENHANCE			0x4274
+#define		GA_DEADLOCK_CNTL			(1 << 0)
+#define		GA_FASTSYNC_CNTL			(1 << 1)
+#define	GA_POLY_MODE			0x4288
+#define		FRONT_PTYPE_POINT			(0 << 4)
+#define		FRONT_PTYPE_LINE			(1 << 4)
+#define		FRONT_PTYPE_TRIANGE			(2 << 4)
+#define		BACK_PTYPE_POINT			(0 << 7)
+#define		BACK_PTYPE_LINE				(1 << 7)
+#define		BACK_PTYPE_TRIANGE			(2 << 7)
+#define	GA_ROUND_MODE			0x428C
+#define		GEOMETRY_ROUND_TRUNC			(0 << 0)
+#define		GEOMETRY_ROUND_NEAREST			(1 << 0)
+#define		COLOR_ROUND_TRUNC			(0 << 2)
+#define		COLOR_ROUND_NEAREST			(1 << 2)
+#define	SU_REG_DEST			0x42C8
+#define	RB3D_DSTCACHE_CTLSTAT		0x4E4C
+#define		RB3D_DC_FLUSH				(2 << 0)
+#define		RB3D_DC_FREE				(2 << 2)
+#define		RB3D_DC_FINISH				(1 << 4)
+#define ZB_ZCACHE_CTLSTAT		0x4F18
+#define		ZC_FLUSH				(1 << 0)
+#define		ZC_FREE					(1 << 1)
+#define DC_LB_MEMORY_SPLIT		0x6520
+#define		DC_LB_MEMORY_SPLIT_MASK			0x00000003
+#define		DC_LB_MEMORY_SPLIT_SHIFT		0
+#define		DC_LB_MEMORY_SPLIT_D1HALF_D2HALF	0
+#define		DC_LB_MEMORY_SPLIT_D1_3Q_D2_1Q		1
+#define		DC_LB_MEMORY_SPLIT_D1_ONLY		2
+#define		DC_LB_MEMORY_SPLIT_D1_1Q_D2_3Q		3
+#define		DC_LB_MEMORY_SPLIT_SHIFT_MODE		(1 << 2)
+#define		DC_LB_DISP1_END_ADR_SHIFT		4
+#define		DC_LB_DISP1_END_ADR_MASK		0x00007FF0
+#define D1MODE_PRIORITY_A_CNT		0x6548
+#define		MODE_PRIORITY_MARK_MASK			0x00007FFF
+#define		MODE_PRIORITY_OFF			(1 << 16)
+#define		MODE_PRIORITY_ALWAYS_ON			(1 << 20)
+#define		MODE_PRIORITY_FORCE_MASK		(1 << 24)
+#define D1MODE_PRIORITY_B_CNT		0x654C
+#define LB_MAX_REQ_OUTSTANDING		0x6D58
+#define		LB_D1_MAX_REQ_OUTSTANDING_MASK		0x0000000F
+#define		LB_D1_MAX_REQ_OUTSTANDING_SHIFT		0
+#define		LB_D2_MAX_REQ_OUTSTANDING_MASK		0x000F0000
+#define		LB_D2_MAX_REQ_OUTSTANDING_SHIFT		16
+#define D2MODE_PRIORITY_A_CNT		0x6D48
+#define D2MODE_PRIORITY_B_CNT		0x6D4C
+
+/* ix[MC] registers */
+#define MC_FB_LOCATION			0x01
+#define		MC_FB_START_MASK			0x0000FFFF
+#define		MC_FB_START_SHIFT			0
+#define		MC_FB_TOP_MASK				0xFFFF0000
+#define		MC_FB_TOP_SHIFT				16
+#define MC_AGP_LOCATION			0x02
+#define		MC_AGP_START_MASK			0x0000FFFF
+#define		MC_AGP_START_SHIFT			0
+#define		MC_AGP_TOP_MASK				0xFFFF0000
+#define		MC_AGP_TOP_SHIFT			16
+#define MC_AGP_BASE			0x03
+#define MC_AGP_BASE_2			0x04
+#define	MC_CNTL				0x5
+#define		MEM_NUM_CHANNELS_MASK			0x00000003
+#define	MC_STATUS			0x08
+#define		MC_STATUS_IDLE				(1 << 4)
+#define	MC_MISC_LAT_TIMER		0x09
+#define		MC_CPR_INIT_LAT_MASK			0x0000000F
+#define		MC_VF_INIT_LAT_MASK			0x000000F0
+#define		MC_DISP0R_INIT_LAT_MASK			0x00000F00
+#define		MC_DISP0R_INIT_LAT_SHIFT		8
+#define		MC_DISP1R_INIT_LAT_MASK			0x0000F000
+#define		MC_DISP1R_INIT_LAT_SHIFT		12
+#define		MC_FIXED_INIT_LAT_MASK			0x000F0000
+#define		MC_E2R_INIT_LAT_MASK			0x00F00000
+#define		SAME_PAGE_PRIO_MASK			0x0F000000
+#define		MC_GLOBW_INIT_LAT_MASK			0xF0000000
+
+
+#endif
+
-- 
GitLab


From e46074effd5510e7a8fe34b93828d98a50835da2 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Michel=20D=C3=A4nzer?= <daenzer@vmware.com>
Date: Tue, 28 Jul 2009 12:30:55 +0200
Subject: [PATCH 0206/1153] drm/radeon: Don't unreserve twice on failure to
 validate.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

This is done later in radeon_object_list_unvalidate(). Doing it twice triggers
a BUG in TTM, rendering X on KMS unusable until reboot.

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_object.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c
index d5b1fd562d8..3961a44c5dc 100644
--- a/drivers/gpu/drm/radeon/radeon_object.c
+++ b/drivers/gpu/drm/radeon/radeon_object.c
@@ -433,7 +433,6 @@ int radeon_object_list_validate(struct list_head *head, void *fence)
 						       robj->tobj.proposed_placement,
 						       true, false);
 			if (unlikely(r)) {
-				radeon_object_list_unreserve(head);
 				DRM_ERROR("radeon: failed to validate.\n");
 				return r;
 			}
-- 
GitLab


From 1ab2e1059916b917af19e4137a4222988bd7a169 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Michel=20D=C3=A4nzer?= <daenzer@vmware.com>
Date: Tue, 28 Jul 2009 12:30:56 +0200
Subject: [PATCH 0207/1153] drm/radeon: Fall back to evicting BOs with memcpy
 if necessary.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Otherwise if there's no GTT space we would fail the eviction, leading to
cascaded failure.

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_ttm.c | 15 +++++++++------
 1 file changed, 9 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c
index 37e1cbcce3a..f3469b96208 100644
--- a/drivers/gpu/drm/radeon/radeon_ttm.c
+++ b/drivers/gpu/drm/radeon/radeon_ttm.c
@@ -355,23 +355,26 @@ static int radeon_bo_move(struct ttm_buffer_object *bo,
 	if (!rdev->cp.ready) {
 		/* use memcpy */
 		DRM_ERROR("CP is not ready use memcpy.\n");
-		return ttm_bo_move_memcpy(bo, evict, no_wait, new_mem);
+		goto memcpy;
 	}
 
 	if (old_mem->mem_type == TTM_PL_VRAM &&
 	    new_mem->mem_type == TTM_PL_SYSTEM) {
-		return radeon_move_vram_ram(bo, evict, interruptible,
+		r = radeon_move_vram_ram(bo, evict, interruptible,
 					    no_wait, new_mem);
 	} else if (old_mem->mem_type == TTM_PL_SYSTEM &&
 		   new_mem->mem_type == TTM_PL_VRAM) {
-		return radeon_move_ram_vram(bo, evict, interruptible,
+		r = radeon_move_ram_vram(bo, evict, interruptible,
 					    no_wait, new_mem);
 	} else {
 		r = radeon_move_blit(bo, evict, no_wait, new_mem, old_mem);
-		if (unlikely(r)) {
-			return r;
-		}
 	}
+
+	if (r) {
+memcpy:
+		r = ttm_bo_move_memcpy(bo, evict, no_wait, new_mem);
+	}
+
 	return r;
 }
 
-- 
GitLab


From 664f86590295217b2319edf88830e87b800f6c4a Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Michel=20D=C3=A4nzer?= <daenzer@vmware.com>
Date: Tue, 28 Jul 2009 12:30:57 +0200
Subject: [PATCH 0208/1153] drm/radeon: Pay more attention to object placement
 requested by userspace.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Previously we were basically always setting the GTT and VRAM flags regardless of
what userspace requested.

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_object.c | 25 +++++++++++--------------
 1 file changed, 11 insertions(+), 14 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c
index 3961a44c5dc..81573c3a9b4 100644
--- a/drivers/gpu/drm/radeon/radeon_object.c
+++ b/drivers/gpu/drm/radeon/radeon_object.c
@@ -103,16 +103,16 @@ static inline uint32_t radeon_object_flags_from_domain(uint32_t domain)
 {
 	uint32_t flags = 0;
 	if (domain & RADEON_GEM_DOMAIN_VRAM) {
-		flags |= TTM_PL_FLAG_VRAM;
+		flags |= TTM_PL_FLAG_VRAM | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED;
 	}
 	if (domain & RADEON_GEM_DOMAIN_GTT) {
-		flags |= TTM_PL_FLAG_TT;
+		flags |= TTM_PL_FLAG_TT | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED;
 	}
 	if (domain & RADEON_GEM_DOMAIN_CPU) {
-		flags |= TTM_PL_FLAG_SYSTEM;
+		flags |= TTM_PL_FLAG_SYSTEM | TTM_PL_MASK_CACHING;
 	}
 	if (!flags) {
-		flags |= TTM_PL_FLAG_SYSTEM;
+		flags |= TTM_PL_FLAG_SYSTEM | TTM_PL_MASK_CACHING;
 	}
 	return flags;
 }
@@ -408,7 +408,6 @@ int radeon_object_list_validate(struct list_head *head, void *fence)
 	struct radeon_object *robj;
 	struct radeon_fence *old_fence = NULL;
 	struct list_head *i;
-	uint32_t flags;
 	int r;
 
 	r = radeon_object_list_reserve(head);
@@ -419,16 +418,14 @@ int radeon_object_list_validate(struct list_head *head, void *fence)
 	list_for_each(i, head) {
 		lobj = list_entry(i, struct radeon_object_list, list);
 		robj = lobj->robj;
-		if (lobj->wdomain) {
-			flags = radeon_object_flags_from_domain(lobj->wdomain);
-			flags |= TTM_PL_FLAG_TT;
-		} else {
-			flags = radeon_object_flags_from_domain(lobj->rdomain);
-			flags |= TTM_PL_FLAG_TT;
-			flags |= TTM_PL_FLAG_VRAM;
-		}
 		if (!robj->pin_count) {
-			robj->tobj.proposed_placement = flags | TTM_PL_MASK_CACHING;
+			if (lobj->wdomain) {
+				robj->tobj.proposed_placement =
+					radeon_object_flags_from_domain(lobj->wdomain);
+			} else {
+				robj->tobj.proposed_placement =
+					radeon_object_flags_from_domain(lobj->rdomain);
+			}
 			r = ttm_buffer_object_validate(&robj->tobj,
 						       robj->tobj.proposed_placement,
 						       true, false);
-- 
GitLab


From 7a50f01a4ab89d5c05eb2cf62e206ac0bfc61d2c Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Tue, 21 Jul 2009 20:39:30 +1000
Subject: [PATCH 0209/1153] drm/radeon/kms: vram sizing on certain r100 chips
 needs workaround.

If an rn50/r100/m6/m7 GPU has < 64MB RAM, i.e. 8/16/32, the
aperture used to calculate the MC_FB_LOCATION needs to be worked
out from the CONFIG_APER_SIZE register, and not the actual vram size.

TTM VRAM size was also being initialised wrong, use actual vram size
to initialise it.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r100.c          | 34 +++++++++++++++++---------
 drivers/gpu/drm/radeon/r520.c          |  4 +--
 drivers/gpu/drm/radeon/r600.c          |  5 ++--
 drivers/gpu/drm/radeon/radeon.h        |  5 +++-
 drivers/gpu/drm/radeon/radeon_device.c | 20 ++++++++-------
 drivers/gpu/drm/radeon/radeon_gem.c    |  4 +--
 drivers/gpu/drm/radeon/radeon_ttm.c    |  4 +--
 drivers/gpu/drm/radeon/rs400.c         |  4 +--
 drivers/gpu/drm/radeon/rs600.c         |  2 +-
 drivers/gpu/drm/radeon/rs690.c         |  7 +++---
 drivers/gpu/drm/radeon/rv515.c         |  7 ++----
 drivers/gpu/drm/radeon/rv770.c         |  2 +-
 12 files changed, 56 insertions(+), 42 deletions(-)

diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index 0e00fef0b84..05a44896dff 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -173,8 +173,12 @@ void r100_mc_setup(struct radeon_device *rdev)
 		DRM_ERROR("Failed to register debugfs file for R100 MC !\n");
 	}
 	/* Write VRAM size in case we are limiting it */
-	WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size);
-	tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1;
+	WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size);
+	/* Novell bug 204882 for RN50/M6/M7 with 8/16/32MB VRAM,
+	 * if the aperture is 64MB but we have 32MB VRAM
+	 * we report only 32MB VRAM but we have to set MC_FB_LOCATION
+	 * to 64MB, otherwise the gpu accidentially dies */
+	tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1;
 	tmp = REG_SET(RADEON_MC_FB_TOP, tmp >> 16);
 	tmp |= REG_SET(RADEON_MC_FB_START, rdev->mc.vram_location >> 16);
 	WREG32(RADEON_MC_FB_LOCATION, tmp);
@@ -1447,25 +1451,28 @@ void r100_vram_init_sizes(struct radeon_device *rdev)
 		uint32_t tom;
 		/* read NB_TOM to get the amount of ram stolen for the GPU */
 		tom = RREG32(RADEON_NB_TOM);
-		rdev->mc.vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16);
+		rdev->mc.real_vram_size = (((tom >> 16) - (tom & 0xffff) + 1) << 16);
 		/* for IGPs we need to keep VRAM where it was put by the BIOS */
 		rdev->mc.vram_location = (tom & 0xffff) << 16;
-		WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size);
+		WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size);
+		rdev->mc.mc_vram_size = rdev->mc.real_vram_size;
 	} else {
-		rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE);
+		rdev->mc.real_vram_size = RREG32(RADEON_CONFIG_MEMSIZE);
 		/* Some production boards of m6 will report 0
 		 * if it's 8 MB
 		 */
-		if (rdev->mc.vram_size == 0) {
-			rdev->mc.vram_size = 8192 * 1024;
-			WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size);
+		if (rdev->mc.real_vram_size == 0) {
+			rdev->mc.real_vram_size = 8192 * 1024;
+			WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size);
 		}
 		/* let driver place VRAM */
 		rdev->mc.vram_location = 0xFFFFFFFFUL;
 		 /* Fix for RN50, M6, M7 with 8/16/32(??) MBs of VRAM - 
 		  * Novell bug 204882 + along with lots of ubuntu ones */
-		if (config_aper_size > rdev->mc.vram_size)
-			rdev->mc.vram_size = config_aper_size;
+		if (config_aper_size > rdev->mc.real_vram_size)
+			rdev->mc.mc_vram_size = config_aper_size;
+		else
+			rdev->mc.mc_vram_size = rdev->mc.real_vram_size;
 	}
 
 	/* work out accessible VRAM */
@@ -1477,8 +1484,11 @@ void r100_vram_init_sizes(struct radeon_device *rdev)
 	if (accessible > rdev->mc.aper_size)
 		accessible = rdev->mc.aper_size;
 
-	if (rdev->mc.vram_size > rdev->mc.aper_size)
-		rdev->mc.vram_size = rdev->mc.aper_size;
+	if (rdev->mc.mc_vram_size > rdev->mc.aper_size)
+		rdev->mc.mc_vram_size = rdev->mc.aper_size;
+
+	if (rdev->mc.real_vram_size > rdev->mc.aper_size)
+		rdev->mc.real_vram_size = rdev->mc.aper_size;
 }
 
 void r100_vram_info(struct radeon_device *rdev)
diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c
index 0a981e2ee2f..09fb0b6ec7d 100644
--- a/drivers/gpu/drm/radeon/r520.c
+++ b/drivers/gpu/drm/radeon/r520.c
@@ -95,8 +95,8 @@ int r520_mc_init(struct radeon_device *rdev)
 		       "programming pipes. Bad things might happen.\n");
 	}
 	/* Write VRAM size in case we are limiting it */
-	WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size);
-	tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1;
+	WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size);
+	tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1;
 	tmp = REG_SET(R520_MC_FB_TOP, tmp >> 16);
 	tmp |= REG_SET(R520_MC_FB_START, rdev->mc.vram_location >> 16);
 	WREG32_MC(R520_MC_FB_LOCATION, tmp);
diff --git a/drivers/gpu/drm/radeon/r600.c b/drivers/gpu/drm/radeon/r600.c
index c45559fc97f..538cd907df6 100644
--- a/drivers/gpu/drm/radeon/r600.c
+++ b/drivers/gpu/drm/radeon/r600.c
@@ -67,7 +67,7 @@ int r600_mc_init(struct radeon_device *rdev)
 		       "programming pipes. Bad things might happen.\n");
 	}
 
-	tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1;
+	tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1;
 	tmp = REG_SET(R600_MC_FB_TOP, tmp >> 24);
 	tmp |= REG_SET(R600_MC_FB_BASE, rdev->mc.vram_location >> 24);
 	WREG32(R600_MC_VM_FB_LOCATION, tmp);
@@ -140,7 +140,8 @@ void r600_vram_get_type(struct radeon_device *rdev)
 void r600_vram_info(struct radeon_device *rdev)
 {
 	r600_vram_get_type(rdev);
-	rdev->mc.vram_size = RREG32(R600_CONFIG_MEMSIZE);
+	rdev->mc.real_vram_size = RREG32(R600_CONFIG_MEMSIZE);
+	rdev->mc.mc_vram_size = rdev->mc.real_vram_size;
 
 	/* Could aper size report 0 ? */
 	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index 63a3fe32e58..045b33b3bf2 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -332,8 +332,11 @@ struct radeon_mc {
 	unsigned		gtt_location;
 	unsigned		gtt_size;
 	unsigned		vram_location;
-	unsigned		vram_size;
+	/* for some chips with <= 32MB we need to lie
+	 * about vram size near mc fb location */
+	unsigned		mc_vram_size;
 	unsigned		vram_width;
+	unsigned		real_vram_size;
 	int			vram_mtrr;
 	bool			vram_is_ddr;
 };
diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c
index f78db5c8008..6d1749e4422 100644
--- a/drivers/gpu/drm/radeon/radeon_device.c
+++ b/drivers/gpu/drm/radeon/radeon_device.c
@@ -121,7 +121,7 @@ int radeon_mc_setup(struct radeon_device *rdev)
 	if (rdev->mc.vram_location != 0xFFFFFFFFUL) {
 		/* vram location was already setup try to put gtt after
 		 * if it fits */
-		tmp = rdev->mc.vram_location + rdev->mc.vram_size;
+		tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size;
 		tmp = (tmp + rdev->mc.gtt_size - 1) & ~(rdev->mc.gtt_size - 1);
 		if ((0xFFFFFFFFUL - tmp) >= rdev->mc.gtt_size) {
 			rdev->mc.gtt_location = tmp;
@@ -136,13 +136,13 @@ int radeon_mc_setup(struct radeon_device *rdev)
 	} else if (rdev->mc.gtt_location != 0xFFFFFFFFUL) {
 		/* gtt location was already setup try to put vram before
 		 * if it fits */
-		if (rdev->mc.vram_size < rdev->mc.gtt_location) {
+		if (rdev->mc.mc_vram_size < rdev->mc.gtt_location) {
 			rdev->mc.vram_location = 0;
 		} else {
 			tmp = rdev->mc.gtt_location + rdev->mc.gtt_size;
-			tmp += (rdev->mc.vram_size - 1);
-			tmp &= ~(rdev->mc.vram_size - 1);
-			if ((0xFFFFFFFFUL - tmp) >= rdev->mc.vram_size) {
+			tmp += (rdev->mc.mc_vram_size - 1);
+			tmp &= ~(rdev->mc.mc_vram_size - 1);
+			if ((0xFFFFFFFFUL - tmp) >= rdev->mc.mc_vram_size) {
 				rdev->mc.vram_location = tmp;
 			} else {
 				printk(KERN_ERR "[drm] vram too big to fit "
@@ -152,12 +152,14 @@ int radeon_mc_setup(struct radeon_device *rdev)
 		}
 	} else {
 		rdev->mc.vram_location = 0;
-		rdev->mc.gtt_location = rdev->mc.vram_size;
+		rdev->mc.gtt_location = rdev->mc.mc_vram_size;
 	}
-	DRM_INFO("radeon: VRAM %uM\n", rdev->mc.vram_size >> 20);
+	DRM_INFO("radeon: VRAM %uM\n", rdev->mc.real_vram_size >> 20);
 	DRM_INFO("radeon: VRAM from 0x%08X to 0x%08X\n",
 		 rdev->mc.vram_location,
-		 rdev->mc.vram_location + rdev->mc.vram_size - 1);
+		 rdev->mc.vram_location + rdev->mc.mc_vram_size - 1);
+	if (rdev->mc.real_vram_size != rdev->mc.mc_vram_size)
+		DRM_INFO("radeon: VRAM less than aperture workaround enabled\n");
 	DRM_INFO("radeon: GTT %uM\n", rdev->mc.gtt_size >> 20);
 	DRM_INFO("radeon: GTT from 0x%08X to 0x%08X\n",
 		 rdev->mc.gtt_location,
@@ -573,7 +575,7 @@ int radeon_device_init(struct radeon_device *rdev,
 	rdev->mc.vram_mtrr = mtrr_add(rdev->mc.aper_base, rdev->mc.aper_size,
 				      MTRR_TYPE_WRCOMB, 1);
 	DRM_INFO("Detected VRAM RAM=%uM, BAR=%uM\n",
-		 rdev->mc.vram_size >> 20,
+		 rdev->mc.real_vram_size >> 20,
 		 (unsigned)rdev->mc.aper_size >> 20);
 	DRM_INFO("RAM width %dbits %cDR\n",
 		 rdev->mc.vram_width, rdev->mc.vram_is_ddr ? 'D' : 'S');
diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c
index 12542087b29..cded5180c75 100644
--- a/drivers/gpu/drm/radeon/radeon_gem.c
+++ b/drivers/gpu/drm/radeon/radeon_gem.c
@@ -157,9 +157,9 @@ int radeon_gem_info_ioctl(struct drm_device *dev, void *data,
 	struct radeon_device *rdev = dev->dev_private;
 	struct drm_radeon_gem_info *args = data;
 
-	args->vram_size = rdev->mc.vram_size;
+	args->vram_size = rdev->mc.real_vram_size;
 	/* FIXME: report somethings that makes sense */
-	args->vram_visible = rdev->mc.vram_size - (4 * 1024 * 1024);
+	args->vram_visible = rdev->mc.real_vram_size - (4 * 1024 * 1024);
 	args->gart_size = rdev->mc.gtt_size;
 	return 0;
 }
diff --git a/drivers/gpu/drm/radeon/radeon_ttm.c b/drivers/gpu/drm/radeon/radeon_ttm.c
index f3469b96208..15c3531377e 100644
--- a/drivers/gpu/drm/radeon/radeon_ttm.c
+++ b/drivers/gpu/drm/radeon/radeon_ttm.c
@@ -454,7 +454,7 @@ int radeon_ttm_init(struct radeon_device *rdev)
 		return r;
 	}
 	r = ttm_bo_init_mm(&rdev->mman.bdev, TTM_PL_VRAM, 0,
-			   ((rdev->mc.aper_size) >> PAGE_SHIFT));
+			   ((rdev->mc.real_vram_size) >> PAGE_SHIFT));
 	if (r) {
 		DRM_ERROR("Failed initializing VRAM heap.\n");
 		return r;
@@ -471,7 +471,7 @@ int radeon_ttm_init(struct radeon_device *rdev)
 		return r;
 	}
 	DRM_INFO("radeon: %uM of VRAM memory ready\n",
-		 rdev->mc.vram_size / (1024 * 1024));
+		 rdev->mc.real_vram_size / (1024 * 1024));
 	r = ttm_bo_init_mm(&rdev->mman.bdev, TTM_PL_TT, 0,
 			   ((rdev->mc.gtt_size) >> PAGE_SHIFT));
 	if (r) {
diff --git a/drivers/gpu/drm/radeon/rs400.c b/drivers/gpu/drm/radeon/rs400.c
index 96a3c8486d2..b29affd9c5d 100644
--- a/drivers/gpu/drm/radeon/rs400.c
+++ b/drivers/gpu/drm/radeon/rs400.c
@@ -233,7 +233,7 @@ int rs400_mc_init(struct radeon_device *rdev)
 
 	rs400_gpu_init(rdev);
 	rs400_gart_disable(rdev);
-	rdev->mc.gtt_location = rdev->mc.vram_size;
+	rdev->mc.gtt_location = rdev->mc.mc_vram_size;
 	rdev->mc.gtt_location += (rdev->mc.gtt_size - 1);
 	rdev->mc.gtt_location &= ~(rdev->mc.gtt_size - 1);
 	r = radeon_mc_setup(rdev);
@@ -247,7 +247,7 @@ int rs400_mc_init(struct radeon_device *rdev)
 		       "programming pipes. Bad things might happen.\n");
 	}
 
-	tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1;
+	tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1;
 	tmp = REG_SET(RADEON_MC_FB_TOP, tmp >> 16);
 	tmp |= REG_SET(RADEON_MC_FB_START, rdev->mc.vram_location >> 16);
 	WREG32(RADEON_MC_FB_LOCATION, tmp);
diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c
index bccdce7fd37..bbea6dee4a9 100644
--- a/drivers/gpu/drm/radeon/rs600.c
+++ b/drivers/gpu/drm/radeon/rs600.c
@@ -223,7 +223,7 @@ int rs600_mc_init(struct radeon_device *rdev)
 		printk(KERN_WARNING "Failed to wait MC idle while "
 		       "programming pipes. Bad things might happen.\n");
 	}
-	tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1;
+	tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1;
 	tmp = REG_SET(RS600_MC_FB_TOP, tmp >> 16);
 	tmp |= REG_SET(RS600_MC_FB_START, rdev->mc.vram_location >> 16);
 	WREG32_MC(RS600_MC_FB_LOCATION, tmp);
diff --git a/drivers/gpu/drm/radeon/rs690.c b/drivers/gpu/drm/radeon/rs690.c
index 97eaee3d28b..839595b0072 100644
--- a/drivers/gpu/drm/radeon/rs690.c
+++ b/drivers/gpu/drm/radeon/rs690.c
@@ -67,7 +67,7 @@ int rs690_mc_init(struct radeon_device *rdev)
 	rs400_gart_disable(rdev);
 
 	/* Setup GPU memory space */
-	rdev->mc.gtt_location = rdev->mc.vram_size;
+	rdev->mc.gtt_location = rdev->mc.mc_vram_size;
 	rdev->mc.gtt_location += (rdev->mc.gtt_size - 1);
 	rdev->mc.gtt_location &= ~(rdev->mc.gtt_size - 1);
 	rdev->mc.vram_location = 0xFFFFFFFFUL;
@@ -82,7 +82,7 @@ int rs690_mc_init(struct radeon_device *rdev)
 		printk(KERN_WARNING "Failed to wait MC idle while "
 		       "programming pipes. Bad things might happen.\n");
 	}
-	tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1;
+	tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1;
 	tmp = REG_SET(RS690_MC_FB_TOP, tmp >> 16);
 	tmp |= REG_SET(RS690_MC_FB_START, rdev->mc.vram_location >> 16);
 	WREG32_MC(RS690_MCCFG_FB_LOCATION, tmp);
@@ -228,7 +228,8 @@ void rs690_vram_info(struct radeon_device *rdev)
 	} else {
 		rdev->mc.vram_width = 64;
 	}
-	rdev->mc.vram_size = RREG32(RADEON_CONFIG_MEMSIZE);
+	rdev->mc.real_vram_size = RREG32(RADEON_CONFIG_MEMSIZE);
+	rdev->mc.mc_vram_size = rdev->mc.real_vram_size;
 
 	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
 	rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0);
diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c
index 4fd411893b9..551e608702e 100644
--- a/drivers/gpu/drm/radeon/rv515.c
+++ b/drivers/gpu/drm/radeon/rv515.c
@@ -100,10 +100,10 @@ int rv515_mc_init(struct radeon_device *rdev)
 		       "programming pipes. Bad things might happen.\n");
 	}
 	/* Write VRAM size in case we are limiting it */
-	WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.vram_size);
+	WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size);
 	tmp = REG_SET(MC_FB_START, rdev->mc.vram_location >> 16);
 	WREG32(0x134, tmp);
-	tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1;
+	tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1;
 	tmp = REG_SET(MC_FB_TOP, tmp >> 16);
 	tmp |= REG_SET(MC_FB_START, rdev->mc.vram_location >> 16);
 	WREG32_MC(MC_FB_LOCATION, tmp);
@@ -369,10 +369,7 @@ void rv515_vram_info(struct radeon_device *rdev)
 	fixed20_12 a;
 
 	rv515_vram_get_type(rdev);
-	rdev->mc.vram_size = RREG32(CONFIG_MEMSIZE);
 
-	rdev->mc.aper_base = drm_get_resource_start(rdev->ddev, 0);
-	rdev->mc.aper_size = drm_get_resource_len(rdev->ddev, 0);
 	/* FIXME: we should enforce default clock in case GPU is not in
 	 * default setup
 	 */
diff --git a/drivers/gpu/drm/radeon/rv770.c b/drivers/gpu/drm/radeon/rv770.c
index da50cc51ede..21d8ffd5730 100644
--- a/drivers/gpu/drm/radeon/rv770.c
+++ b/drivers/gpu/drm/radeon/rv770.c
@@ -67,7 +67,7 @@ int rv770_mc_init(struct radeon_device *rdev)
 		       "programming pipes. Bad things might happen.\n");
 	}
 
-	tmp = rdev->mc.vram_location + rdev->mc.vram_size - 1;
+	tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1;
 	tmp = REG_SET(R700_MC_FB_TOP, tmp >> 24);
 	tmp |= REG_SET(R700_MC_FB_BASE, rdev->mc.vram_location >> 24);
 	WREG32(R700_MC_VM_FB_LOCATION, tmp);
-- 
GitLab


From 4677f15c60421d48566c48c3149474e64977f071 Mon Sep 17 00:00:00 2001
From: Thomas Hellstrom <thellstrom@vmware.com>
Date: Tue, 21 Jul 2009 17:45:13 +0200
Subject: [PATCH 0210/1153] drm/ttm: Fix an oops and sync object leak.

The code was potentially dereferencig a NULL sync object pointer.
At the same time a sync object reference was potentially leaked.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/ttm/ttm_bo_util.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/ttm/ttm_bo_util.c b/drivers/gpu/drm/ttm/ttm_bo_util.c
index bdec583901e..3e5d0c4ad85 100644
--- a/drivers/gpu/drm/ttm/ttm_bo_util.c
+++ b/drivers/gpu/drm/ttm/ttm_bo_util.c
@@ -509,8 +509,8 @@ int ttm_bo_move_accel_cleanup(struct ttm_buffer_object *bo,
 	if (evict) {
 		ret = ttm_bo_wait(bo, false, false, false);
 		spin_unlock(&bo->lock);
-		driver->sync_obj_unref(&bo->sync_obj);
-
+		if (tmp_obj)
+			driver->sync_obj_unref(&tmp_obj);
 		if (ret)
 			return ret;
 
@@ -532,6 +532,8 @@ int ttm_bo_move_accel_cleanup(struct ttm_buffer_object *bo,
 
 		set_bit(TTM_BO_PRIV_FLAG_MOVING, &bo->priv_flags);
 		spin_unlock(&bo->lock);
+		if (tmp_obj)
+			driver->sync_obj_unref(&tmp_obj);
 
 		ret = ttm_buffer_object_transfer(bo, &ghost_obj);
 		if (ret)
-- 
GitLab


From 542c6f6df51327dbb180cf4d9b34827e147efe17 Mon Sep 17 00:00:00 2001
From: Thomas Hellstrom <thellstrom@vmware.com>
Date: Fri, 24 Jul 2009 09:57:34 +0200
Subject: [PATCH 0211/1153] drm/ttm: Fix ttm in-kernel copying of pages with
 non-standard caching attributes.

For x86 this affected highmem pages only, since they were always kmapped
cache-coherent, and this is fixed using kmap_atomic_prot().

For other architectures that may not modify the linear kernel map we
resort to vmap() for now, since kmap_atomic_prot() generally uses the
linear kernel map for lowmem pages. This of course comes with a
performance impact and should be optimized when possible.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/ttm/ttm_bo_util.c | 63 +++++++++++++++++++++++++------
 1 file changed, 52 insertions(+), 11 deletions(-)

diff --git a/drivers/gpu/drm/ttm/ttm_bo_util.c b/drivers/gpu/drm/ttm/ttm_bo_util.c
index 3e5d0c4ad85..ce2e6f38ea0 100644
--- a/drivers/gpu/drm/ttm/ttm_bo_util.c
+++ b/drivers/gpu/drm/ttm/ttm_bo_util.c
@@ -136,7 +136,8 @@ static int ttm_copy_io_page(void *dst, void *src, unsigned long page)
 }
 
 static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src,
-				unsigned long page)
+				unsigned long page,
+				pgprot_t prot)
 {
 	struct page *d = ttm_tt_get_page(ttm, page);
 	void *dst;
@@ -145,17 +146,35 @@ static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src,
 		return -ENOMEM;
 
 	src = (void *)((unsigned long)src + (page << PAGE_SHIFT));
-	dst = kmap(d);
+
+#ifdef CONFIG_X86
+	dst = kmap_atomic_prot(d, KM_USER0, prot);
+#else
+	if (prot != PAGE_KERNEL)
+		dst = vmap(&d, 1, 0, prot);
+	else
+		dst = kmap(d);
+#endif
 	if (!dst)
 		return -ENOMEM;
 
 	memcpy_fromio(dst, src, PAGE_SIZE);
-	kunmap(d);
+
+#ifdef CONFIG_X86
+	kunmap_atomic(dst, KM_USER0);
+#else
+	if (prot != PAGE_KERNEL)
+		vunmap(dst);
+	else
+		kunmap(d);
+#endif
+
 	return 0;
 }
 
 static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst,
-				unsigned long page)
+				unsigned long page,
+				pgprot_t prot)
 {
 	struct page *s = ttm_tt_get_page(ttm, page);
 	void *src;
@@ -164,12 +183,28 @@ static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst,
 		return -ENOMEM;
 
 	dst = (void *)((unsigned long)dst + (page << PAGE_SHIFT));
-	src = kmap(s);
+#ifdef CONFIG_X86
+	src = kmap_atomic_prot(s, KM_USER0, prot);
+#else
+	if (prot != PAGE_KERNEL)
+		src = vmap(&s, 1, 0, prot);
+	else
+		src = kmap(s);
+#endif
 	if (!src)
 		return -ENOMEM;
 
 	memcpy_toio(dst, src, PAGE_SIZE);
-	kunmap(s);
+
+#ifdef CONFIG_X86
+	kunmap_atomic(src, KM_USER0);
+#else
+	if (prot != PAGE_KERNEL)
+		vunmap(src);
+	else
+		kunmap(s);
+#endif
+
 	return 0;
 }
 
@@ -214,11 +249,17 @@ int ttm_bo_move_memcpy(struct ttm_buffer_object *bo,
 
 	for (i = 0; i < new_mem->num_pages; ++i) {
 		page = i * dir + add;
-		if (old_iomap == NULL)
-			ret = ttm_copy_ttm_io_page(ttm, new_iomap, page);
-		else if (new_iomap == NULL)
-			ret = ttm_copy_io_ttm_page(ttm, old_iomap, page);
-		else
+		if (old_iomap == NULL) {
+			pgprot_t prot = ttm_io_prot(old_mem->placement,
+						    PAGE_KERNEL);
+			ret = ttm_copy_ttm_io_page(ttm, new_iomap, page,
+						   prot);
+		} else if (new_iomap == NULL) {
+			pgprot_t prot = ttm_io_prot(new_mem->placement,
+						    PAGE_KERNEL);
+			ret = ttm_copy_io_ttm_page(ttm, old_iomap, page,
+						   prot);
+		} else
 			ret = ttm_copy_io_page(new_iomap, old_iomap, page);
 		if (ret)
 			goto out1;
-- 
GitLab


From 73ba651fc246fcc3e446da4155e0425b4219d2c4 Mon Sep 17 00:00:00 2001
From: Thomas Hellstrom <thellstrom@vmware.com>
Date: Fri, 24 Jul 2009 09:57:33 +0200
Subject: [PATCH 0212/1153] x86: Export kmap_atomic_prot() needed for TTM.

This functionality is needed to kmap_atomic() highmem pages that may
potentially have or are about to set up other mappings with
non-standard caching attributes.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 arch/x86/mm/highmem_32.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/x86/mm/highmem_32.c b/arch/x86/mm/highmem_32.c
index 58f621e8191..2112ed55e7e 100644
--- a/arch/x86/mm/highmem_32.c
+++ b/arch/x86/mm/highmem_32.c
@@ -103,6 +103,7 @@ EXPORT_SYMBOL(kmap);
 EXPORT_SYMBOL(kunmap);
 EXPORT_SYMBOL(kmap_atomic);
 EXPORT_SYMBOL(kunmap_atomic);
+EXPORT_SYMBOL(kmap_atomic_prot);
 
 void __init set_highmem_pages_init(void)
 {
-- 
GitLab


From f121ecfebbea1452a17d57c656def7d1537440f7 Mon Sep 17 00:00:00 2001
From: Thomas Hellstrom <thellstrom@vmware.com>
Date: Fri, 24 Jul 2009 10:22:36 +0200
Subject: [PATCH 0213/1153] drm/ttm: powerpc: Fix Highmem cache flushing.

Temporarily maps highmem pages while flushing to get a valid virtual
address to flush.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/ttm/ttm_tt.c | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/ttm/ttm_tt.c b/drivers/gpu/drm/ttm/ttm_tt.c
index 81ab81f030a..9b2248a80cf 100644
--- a/drivers/gpu/drm/ttm/ttm_tt.c
+++ b/drivers/gpu/drm/ttm/ttm_tt.c
@@ -86,10 +86,16 @@ void ttm_tt_cache_flush(struct page *pages[], unsigned long num_pages)
 	unsigned long i;
 
 	for (i = 0; i < num_pages; ++i) {
-		if (pages[i]) {
-			unsigned long start = (unsigned long)page_address(pages[i]);
-			flush_dcache_range(start, start + PAGE_SIZE);
-		}
+		struct page *page = pages[i];
+		void *page_virtual;
+
+		if (unlikely(page == NULL))
+			continue;
+
+		page_virtual = kmap_atomic(page, KM_USER0);
+		flush_dcache_range((unsigned long) page_virtual,
+				   (unsigned long) page_virtual + PAGE_SIZE);
+		kunmap_atomic(page_virtual, KM_USER0);
 	}
 #else
 	if (on_each_cpu(ttm_tt_ipi_handler, NULL, 1) != 0)
-- 
GitLab


From 3b170c3b2e688665fbc2845ba5bb4304bf38a119 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Fri, 24 Jul 2009 13:47:45 +1000
Subject: [PATCH 0214/1153] drm/radeon/kms: allow interruptible waits for
 objects.

Blocking here isn't something the X server mouse appreciates,
avoid the block and let userspace retry the waits.

libdrm_radeon userspace library is also expecting EBUSY not ERESTART

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_fence.c  | 2 +-
 drivers/gpu/drm/radeon/radeon_object.c | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_fence.c b/drivers/gpu/drm/radeon/radeon_fence.c
index 96afbf5ae2a..b4e48dd2e85 100644
--- a/drivers/gpu/drm/radeon/radeon_fence.c
+++ b/drivers/gpu/drm/radeon/radeon_fence.c
@@ -195,7 +195,7 @@ retry:
 		r = wait_event_interruptible_timeout(rdev->fence_drv.queue,
 				radeon_fence_signaled(fence), timeout);
 		if (unlikely(r == -ERESTARTSYS)) {
-			return -ERESTART;
+			return -EBUSY;
 		}
 	} else {
 		r = wait_event_timeout(rdev->fence_drv.queue,
diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c
index 81573c3a9b4..dd9ac2fed6d 100644
--- a/drivers/gpu/drm/radeon/radeon_object.c
+++ b/drivers/gpu/drm/radeon/radeon_object.c
@@ -309,7 +309,7 @@ int radeon_object_wait(struct radeon_object *robj)
 	}
 	spin_lock(&robj->tobj.lock);
 	if (robj->tobj.sync_obj) {
-		r = ttm_bo_wait(&robj->tobj, true, false, false);
+		r = ttm_bo_wait(&robj->tobj, true, true, false);
 	}
 	spin_unlock(&robj->tobj.lock);
 	radeon_object_unreserve(robj);
-- 
GitLab


From ecc0b32645bf19a3a240e72be3022ab3b46ad3d0 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Michel=20D=C3=A4nzer?= <daenzer@vmware.com>
Date: Tue, 21 Jul 2009 11:23:57 +0200
Subject: [PATCH 0215/1153] drm/radeon: Add radeon.test parameter for running
 BO GPU copy tests.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

If enabled, during initialization BO GTT->VRAM and VRAM->GTT GPU copies are
tested across the whole GTT aperture.

This has helped uncover the benchmark copy size bug and verify the maximum
aperture size supported by the AGP bridge in my PowerBook.

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/Makefile        |   3 +-
 drivers/gpu/drm/radeon/radeon.h        |   7 +
 drivers/gpu/drm/radeon/radeon_device.c |   3 +
 drivers/gpu/drm/radeon/radeon_drv.c    |   4 +
 drivers/gpu/drm/radeon/radeon_test.c   | 209 +++++++++++++++++++++++++
 5 files changed, 225 insertions(+), 1 deletion(-)
 create mode 100644 drivers/gpu/drm/radeon/radeon_test.c

diff --git a/drivers/gpu/drm/radeon/Makefile b/drivers/gpu/drm/radeon/Makefile
index 5fae1e074b4..013d3805994 100644
--- a/drivers/gpu/drm/radeon/Makefile
+++ b/drivers/gpu/drm/radeon/Makefile
@@ -13,7 +13,8 @@ radeon-$(CONFIG_DRM_RADEON_KMS) += radeon_device.o radeon_kms.o \
 	radeon_encoders.o radeon_display.o radeon_cursor.o radeon_i2c.o \
 	radeon_clocks.o radeon_fb.o radeon_gem.o radeon_ring.o radeon_irq_kms.o \
 	radeon_cs.o radeon_bios.o radeon_benchmark.o r100.o r300.o r420.o \
-	rs400.o rs600.o rs690.o rv515.o r520.o r600.o rs780.o rv770.o
+	rs400.o rs600.o rs690.o rv515.o r520.o r600.o rs780.o rv770.o \
+	radeon_test.o
 
 radeon-$(CONFIG_COMPAT) += radeon_ioc32.o
 
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index 045b33b3bf2..b1d945b8ed6 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -64,6 +64,7 @@ extern int radeon_agpmode;
 extern int radeon_vram_limit;
 extern int radeon_gart_size;
 extern int radeon_benchmarking;
+extern int radeon_testing;
 extern int radeon_connector_table;
 
 /*
@@ -534,6 +535,12 @@ struct radeon_pm {
 void radeon_benchmark(struct radeon_device *rdev);
 
 
+/*
+ * Testing
+ */
+void radeon_test_moves(struct radeon_device *rdev);
+
+
 /*
  * Debugfs
  */
diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c
index 6d1749e4422..a162ade74b7 100644
--- a/drivers/gpu/drm/radeon/radeon_device.c
+++ b/drivers/gpu/drm/radeon/radeon_device.c
@@ -638,6 +638,9 @@ int radeon_device_init(struct radeon_device *rdev,
 	if (!ret) {
 		DRM_INFO("radeon: kernel modesetting successfully initialized.\n");
 	}
+	if (radeon_testing) {
+		radeon_test_moves(rdev);
+	}
 	if (radeon_benchmarking) {
 		radeon_benchmark(rdev);
 	}
diff --git a/drivers/gpu/drm/radeon/radeon_drv.c b/drivers/gpu/drm/radeon/radeon_drv.c
index 84ba69f4878..3cfcee17dc5 100644
--- a/drivers/gpu/drm/radeon/radeon_drv.c
+++ b/drivers/gpu/drm/radeon/radeon_drv.c
@@ -89,6 +89,7 @@ int radeon_agpmode = 0;
 int radeon_vram_limit = 0;
 int radeon_gart_size = 512; /* default gart size */
 int radeon_benchmarking = 0;
+int radeon_testing = 0;
 int radeon_connector_table = 0;
 #endif
 
@@ -117,6 +118,9 @@ module_param_named(gartsize, radeon_gart_size, int, 0600);
 MODULE_PARM_DESC(benchmark, "Run benchmark");
 module_param_named(benchmark, radeon_benchmarking, int, 0444);
 
+MODULE_PARM_DESC(test, "Run tests");
+module_param_named(test, radeon_testing, int, 0444);
+
 MODULE_PARM_DESC(connector_table, "Force connector table");
 module_param_named(connector_table, radeon_connector_table, int, 0444);
 #endif
diff --git a/drivers/gpu/drm/radeon/radeon_test.c b/drivers/gpu/drm/radeon/radeon_test.c
new file mode 100644
index 00000000000..03c33cf4e14
--- /dev/null
+++ b/drivers/gpu/drm/radeon/radeon_test.c
@@ -0,0 +1,209 @@
+/*
+ * Copyright 2009 VMware, Inc.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: Michel Dänzer
+ */
+#include <drm/drmP.h>
+#include <drm/radeon_drm.h>
+#include "radeon_reg.h"
+#include "radeon.h"
+
+
+/* Test BO GTT->VRAM and VRAM->GTT GPU copies across the whole GTT aperture */
+void radeon_test_moves(struct radeon_device *rdev)
+{
+	struct radeon_object *vram_obj = NULL;
+	struct radeon_object **gtt_obj = NULL;
+	struct radeon_fence *fence = NULL;
+	uint64_t gtt_addr, vram_addr;
+	unsigned i, n, size;
+	int r;
+
+	size = 1024 * 1024;
+
+	/* Number of tests =
+	 * (Total GTT - IB pool - writeback page - ring buffer) / test size
+	 */
+	n = (rdev->mc.gtt_size - RADEON_IB_POOL_SIZE*64*1024 - 4096 -
+	     rdev->cp.ring_size) / size;
+
+	gtt_obj = kzalloc(n * sizeof(*gtt_obj), GFP_KERNEL);
+	if (!gtt_obj) {
+		DRM_ERROR("Failed to allocate %d pointers\n", n);
+		r = 1;
+		goto out_cleanup;
+	}
+
+	r = radeon_object_create(rdev, NULL, size, true, RADEON_GEM_DOMAIN_VRAM,
+				 false, &vram_obj);
+	if (r) {
+		DRM_ERROR("Failed to create VRAM object\n");
+		goto out_cleanup;
+	}
+
+	r = radeon_object_pin(vram_obj, RADEON_GEM_DOMAIN_VRAM, &vram_addr);
+	if (r) {
+		DRM_ERROR("Failed to pin VRAM object\n");
+		goto out_cleanup;
+	}
+
+	for (i = 0; i < n; i++) {
+		void *gtt_map, *vram_map;
+		void **gtt_start, **gtt_end;
+		void **vram_start, **vram_end;
+
+		r = radeon_object_create(rdev, NULL, size, true,
+					 RADEON_GEM_DOMAIN_GTT, false, gtt_obj + i);
+		if (r) {
+			DRM_ERROR("Failed to create GTT object %d\n", i);
+			goto out_cleanup;
+		}
+
+		r = radeon_object_pin(gtt_obj[i], RADEON_GEM_DOMAIN_GTT, &gtt_addr);
+		if (r) {
+			DRM_ERROR("Failed to pin GTT object %d\n", i);
+			goto out_cleanup;
+		}
+
+		r = radeon_object_kmap(gtt_obj[i], &gtt_map);
+		if (r) {
+			DRM_ERROR("Failed to map GTT object %d\n", i);
+			goto out_cleanup;
+		}
+
+		for (gtt_start = gtt_map, gtt_end = gtt_map + size;
+		     gtt_start < gtt_end;
+		     gtt_start++)
+			*gtt_start = gtt_start;
+
+		radeon_object_kunmap(gtt_obj[i]);
+
+		r = radeon_fence_create(rdev, &fence);
+		if (r) {
+			DRM_ERROR("Failed to create GTT->VRAM fence %d\n", i);
+			goto out_cleanup;
+		}
+
+		r = radeon_copy(rdev, gtt_addr, vram_addr, size / 4096, fence);
+		if (r) {
+			DRM_ERROR("Failed GTT->VRAM copy %d\n", i);
+			goto out_cleanup;
+		}
+
+		r = radeon_fence_wait(fence, false);
+		if (r) {
+			DRM_ERROR("Failed to wait for GTT->VRAM fence %d\n", i);
+			goto out_cleanup;
+		}
+
+		radeon_fence_unref(&fence);
+
+		r = radeon_object_kmap(vram_obj, &vram_map);
+		if (r) {
+			DRM_ERROR("Failed to map VRAM object after copy %d\n", i);
+			goto out_cleanup;
+		}
+
+		for (gtt_start = gtt_map, gtt_end = gtt_map + size,
+		     vram_start = vram_map, vram_end = vram_map + size;
+		     vram_start < vram_end;
+		     gtt_start++, vram_start++) {
+			if (*vram_start != gtt_start) {
+				DRM_ERROR("Incorrect GTT->VRAM copy %d: Got 0x%p, "
+					  "expected 0x%p (GTT map 0x%p-0x%p)\n",
+					  i, *vram_start, gtt_start, gtt_map,
+					  gtt_end);
+				radeon_object_kunmap(vram_obj);
+				goto out_cleanup;
+			}
+			*vram_start = vram_start;
+		}
+
+		radeon_object_kunmap(vram_obj);
+
+		r = radeon_fence_create(rdev, &fence);
+		if (r) {
+			DRM_ERROR("Failed to create VRAM->GTT fence %d\n", i);
+			goto out_cleanup;
+		}
+
+		r = radeon_copy(rdev, vram_addr, gtt_addr, size / 4096, fence);
+		if (r) {
+			DRM_ERROR("Failed VRAM->GTT copy %d\n", i);
+			goto out_cleanup;
+		}
+
+		r = radeon_fence_wait(fence, false);
+		if (r) {
+			DRM_ERROR("Failed to wait for VRAM->GTT fence %d\n", i);
+			goto out_cleanup;
+		}
+
+		radeon_fence_unref(&fence);
+
+		r = radeon_object_kmap(gtt_obj[i], &gtt_map);
+		if (r) {
+			DRM_ERROR("Failed to map GTT object after copy %d\n", i);
+			goto out_cleanup;
+		}
+
+		for (gtt_start = gtt_map, gtt_end = gtt_map + size,
+		     vram_start = vram_map, vram_end = vram_map + size;
+		     gtt_start < gtt_end;
+		     gtt_start++, vram_start++) {
+			if (*gtt_start != vram_start) {
+				DRM_ERROR("Incorrect VRAM->GTT copy %d: Got 0x%p, "
+					  "expected 0x%p (VRAM map 0x%p-0x%p)\n",
+					  i, *gtt_start, vram_start, vram_map,
+					  vram_end);
+				radeon_object_kunmap(gtt_obj[i]);
+				goto out_cleanup;
+			}
+		}
+
+		radeon_object_kunmap(gtt_obj[i]);
+
+		DRM_INFO("Tested GTT->VRAM and VRAM->GTT copy for GTT offset 0x%llx\n",
+			 gtt_addr - rdev->mc.gtt_location);
+	}
+
+out_cleanup:
+	if (vram_obj) {
+		radeon_object_unpin(vram_obj);
+		radeon_object_unref(&vram_obj);
+	}
+	if (gtt_obj) {
+		for (i = 0; i < n; i++) {
+			if (gtt_obj[i]) {
+				radeon_object_unpin(gtt_obj[i]);
+				radeon_object_unref(&gtt_obj[i]);
+			}
+		}
+		kfree(gtt_obj);
+	}
+	if (fence) {
+		radeon_fence_unref(&fence);
+	}
+	if (r) {
+		printk(KERN_WARNING "Error while testing BO move.\n");
+	}
+}
+
-- 
GitLab


From ea3c13bd8c2ed1d3670bd72e60f562a427355fdf Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Michel=20D=C3=A4nzer?= <daenzer@vmware.com>
Date: Mon, 20 Jul 2009 01:44:03 +0200
Subject: [PATCH 0216/1153] drm/radeon: Fix size used for benchmarking BO
 copies.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

The incorrect size caused benchmark results to be inflated by a factor of 4.

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_benchmark.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_benchmark.c b/drivers/gpu/drm/radeon/radeon_benchmark.c
index c44403a2ca7..2e938f7496f 100644
--- a/drivers/gpu/drm/radeon/radeon_benchmark.c
+++ b/drivers/gpu/drm/radeon/radeon_benchmark.c
@@ -63,7 +63,7 @@ void radeon_benchmark_move(struct radeon_device *rdev, unsigned bsize,
 		if (r) {
 			goto out_cleanup;
 		}
-		r = radeon_copy_dma(rdev, saddr, daddr, size >> 14, fence);
+		r = radeon_copy_dma(rdev, saddr, daddr, size / 4096, fence);
 		if (r) {
 			goto out_cleanup;
 		}
@@ -88,7 +88,7 @@ void radeon_benchmark_move(struct radeon_device *rdev, unsigned bsize,
 		if (r) {
 			goto out_cleanup;
 		}
-		r = radeon_copy_blit(rdev, saddr, daddr, size >> 14, fence);
+		r = radeon_copy_blit(rdev, saddr, daddr, size / 4096, fence);
 		if (r) {
 			goto out_cleanup;
 		}
-- 
GitLab


From b42db2b12df7b4f7b2ace581a7726cb5bcb2d658 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Wed, 29 Jul 2009 16:56:52 +1000
Subject: [PATCH 0217/1153] drm/ttm: fix highuser vs dma32 confusion.

DMA32 and highmem are sort of exclusive.

Noticed by AndrewR on #radeon.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/ttm/ttm_tt.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/ttm/ttm_tt.c b/drivers/gpu/drm/ttm/ttm_tt.c
index 9b2248a80cf..b8b6c4a5f98 100644
--- a/drivers/gpu/drm/ttm/ttm_tt.c
+++ b/drivers/gpu/drm/ttm/ttm_tt.c
@@ -137,13 +137,15 @@ static void ttm_tt_free_page_directory(struct ttm_tt *ttm)
 
 static struct page *ttm_tt_alloc_page(unsigned page_flags)
 {
-	gfp_t gfp_flags = GFP_HIGHUSER;
+	gfp_t gfp_flags = GFP_USER;
 
 	if (page_flags & TTM_PAGE_FLAG_ZERO_ALLOC)
 		gfp_flags |= __GFP_ZERO;
 
 	if (page_flags & TTM_PAGE_FLAG_DMA32)
 		gfp_flags |= __GFP_DMA32;
+	else
+		gfp_flags |= __GFP_HIGHMEM;
 
 	return alloc_page(gfp_flags);
 }
-- 
GitLab


From ed8f0d9e708a1a7c9222e7d0a35d97521e904223 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Wed, 29 Jul 2009 17:07:38 +1000
Subject: [PATCH 0218/1153] drm/radeon: set fb aperture sizes for framebuffer
 handoff.

This will allow efi/vesa to handoff to radeon.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_fb.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c
index 36d2f5588f2..3206c0ad7b6 100644
--- a/drivers/gpu/drm/radeon/radeon_fb.c
+++ b/drivers/gpu/drm/radeon/radeon_fb.c
@@ -602,6 +602,11 @@ int radeonfb_create(struct radeon_device *rdev,
 	info->var.width = -1;
 	info->var.xres = fb_width;
 	info->var.yres = fb_height;
+
+	/* setup aperture base/size for vesafb takeover */
+	info->aperture_base = rdev->ddev->mode_config.fb_base;
+	info->aperture_size = rdev->mc.real_vram_size;
+
 	info->fix.mmio_start = 0;
 	info->fix.mmio_len = 0;
 	info->pixmap.size = 64*1024;
-- 
GitLab


From 78735cffc2d9ab0dec32f1ba7cbc1d84b45bbf29 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Wed, 29 Jul 2009 14:35:20 +0200
Subject: [PATCH 0219/1153] ALSA: hda: fix out-of-bound hdmi_eld.sad[] write

e->sad[] is declared with size ELD_MAX_SAD=16, but the guard
allows range 0-31.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/hda_eld.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/sound/pci/hda/hda_eld.c b/sound/pci/hda/hda_eld.c
index fcad5ec3177..9446a5abea1 100644
--- a/sound/pci/hda/hda_eld.c
+++ b/sound/pci/hda/hda_eld.c
@@ -508,7 +508,7 @@ static void hdmi_write_eld_info(struct snd_info_entry *entry,
 	char name[64];
 	char *sname;
 	long long val;
-	int n;
+	unsigned int n;
 
 	while (!snd_info_get_line(buffer, line, sizeof(line))) {
 		if (sscanf(line, "%s %llx", name, &val) != 2)
@@ -539,7 +539,7 @@ static void hdmi_write_eld_info(struct snd_info_entry *entry,
 				sname++;
 				n = 10 * n + name[4] - '0';
 			}
-			if (n < 0 || n > 31) /* double the CEA limit */
+			if (n >= ELD_MAX_SAD)
 				continue;
 			if (!strcmp(sname, "_coding_type"))
 				e->sad[n].format = val;
-- 
GitLab


From c45ec06c74512265969aef40b00f320c6afb7a90 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Wed, 29 Jul 2009 11:46:59 +0200
Subject: [PATCH 0220/1153] sound: aedsp16: Buffer overflow

DSPVersion is declared as char[3], but the sprintf writes at least 4 bytes
including terminating null.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/oss/aedsp16.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/sound/oss/aedsp16.c b/sound/oss/aedsp16.c
index 3ee9900ffd7..35b5912cf3f 100644
--- a/sound/oss/aedsp16.c
+++ b/sound/oss/aedsp16.c
@@ -325,8 +325,9 @@
 /*
  * Size of character arrays that store name and version of sound card
  */
-#define CARDNAMELEN 15		/* Size of the card's name in chars     */
-#define CARDVERLEN  2		/* Size of the card's version in chars  */
+#define CARDNAMELEN	15	/* Size of the card's name in chars     */
+#define CARDVERLEN	10	/* Size of the card's version in chars	*/
+#define CARDVERDIGITS	2	/* Number of digits in the version	*/
 
 #if defined(CONFIG_SC6600)
 /*
@@ -410,7 +411,7 @@
 
 static int      soft_cfg __initdata = 0;	/* bitmapped config */
 static int      soft_cfg_mss __initdata = 0;	/* bitmapped mss config */
-static int      ver[CARDVERLEN] __initdata = {0, 0};	/* DSP Ver:
+static int      ver[CARDVERDIGITS] __initdata = {0, 0};	/* DSP Ver:
 						   hi->ver[0] lo->ver[1] */
 
 #if defined(CONFIG_SC6600)
@@ -957,7 +958,7 @@ static int __init aedsp16_dsp_version(int port)
 	 * string is finished.
 	 */
 		ver[len++] = ret;
-	  } while (len < CARDVERLEN);
+	  } while (len < CARDVERDIGITS);
 	sprintf(DSPVersion, "%d.%d", ver[0], ver[1]);
 
 	DBG(("success.\n"));
-- 
GitLab


From a987004fbcf163b100d227284999602f83044d7e Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Wed, 29 Jul 2009 12:12:09 +0200
Subject: [PATCH 0221/1153] sound: mpu401.c: Buffer overflow

mpu_synth_info[m].name is a char[30], and the minimum length of the data
written by sprintf is 31 bytes including terminating null.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/oss/mpu401.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/sound/oss/mpu401.c b/sound/oss/mpu401.c
index 1b2316f35b1..734b8f9e2f7 100644
--- a/sound/oss/mpu401.c
+++ b/sound/oss/mpu401.c
@@ -1074,7 +1074,7 @@ int attach_mpu401(struct address_info *hw_config, struct module *owner)
 			sprintf(mpu_synth_info[m].name, "%s (MPU401)", hw_config->name);
 		else
 			sprintf(mpu_synth_info[m].name,
-				"MPU-401 %d.%d%c Midi interface #%d",
+				"MPU-401 %d.%d%c MIDI #%d",
 				(int) (devc->version & 0xf0) >> 4,
 				devc->version & 0x0f,
 				revision_char,
-- 
GitLab


From 430453fc2a5f3f2c1d98ebc3c3d4c54f3060e3c3 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Tue, 28 Jul 2009 09:59:47 +0200
Subject: [PATCH 0222/1153] libertas: Read outside array bounds

reads bss->rates[j] before checking bounds of index, and should use
ARRAY_SIZE to determine the size of the array.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/libertas/scan.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/libertas/scan.c b/drivers/net/wireless/libertas/scan.c
index 601b5424967..6c95af3023c 100644
--- a/drivers/net/wireless/libertas/scan.c
+++ b/drivers/net/wireless/libertas/scan.c
@@ -5,6 +5,7 @@
   *  for sending scan commands to the firmware.
   */
 #include <linux/types.h>
+#include <linux/kernel.h>
 #include <linux/etherdevice.h>
 #include <linux/if_arp.h>
 #include <asm/unaligned.h>
@@ -876,7 +877,7 @@ static inline char *lbs_translate_scan(struct lbs_private *priv,
 	iwe.u.bitrate.disabled = 0;
 	iwe.u.bitrate.value = 0;
 
-	for (j = 0; bss->rates[j] && (j < sizeof(bss->rates)); j++) {
+	for (j = 0; j < ARRAY_SIZE(bss->rates) && bss->rates[j]; j++) {
 		/* Bit rate given in 500 kb/s units */
 		iwe.u.bitrate.value = bss->rates[j] * 500000;
 		current_val = iwe_stream_add_value(info, start, current_val,
-- 
GitLab


From 57921c312e8cef72ba35a4cfe870b376da0b1b87 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Tue, 28 Jul 2009 12:05:00 +0200
Subject: [PATCH 0223/1153] libertas: Read buffer overflow

Several arrays were read before checking whether the index was within
bounds. ARRAY_SIZE() should be used to determine the size of arrays.

rates->rates has an arraysize of 1, so calling get_common_rates()
with a rates_size of MAX_RATES (14) was causing reads out of bounds.

tmp_size can increment at most to (ARRAY_SIZE(lbs_bg_rates) - 1) *
(*rates_size - 1), so that should be the number of elements of tmp[].

A goto can be eliminated: ret was already set upon its declaration.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/libertas/assoc.c | 18 ++++++++----------
 1 file changed, 8 insertions(+), 10 deletions(-)

diff --git a/drivers/net/wireless/libertas/assoc.c b/drivers/net/wireless/libertas/assoc.c
index b9b37411903..d6997371c27 100644
--- a/drivers/net/wireless/libertas/assoc.c
+++ b/drivers/net/wireless/libertas/assoc.c
@@ -1,6 +1,7 @@
 /* Copyright (C) 2006, Red Hat, Inc. */
 
 #include <linux/types.h>
+#include <linux/kernel.h>
 #include <linux/etherdevice.h>
 #include <linux/ieee80211.h>
 #include <linux/if_arp.h>
@@ -43,21 +44,21 @@ static int get_common_rates(struct lbs_private *priv,
 	u16 *rates_size)
 {
 	u8 *card_rates = lbs_bg_rates;
-	size_t num_card_rates = sizeof(lbs_bg_rates);
 	int ret = 0, i, j;
-	u8 tmp[30];
+	u8 tmp[(ARRAY_SIZE(lbs_bg_rates) - 1) * (*rates_size - 1)];
 	size_t tmp_size = 0;
 
 	/* For each rate in card_rates that exists in rate1, copy to tmp */
-	for (i = 0; card_rates[i] && (i < num_card_rates); i++) {
-		for (j = 0; rates[j] && (j < *rates_size); j++) {
+	for (i = 0; i < ARRAY_SIZE(lbs_bg_rates) && card_rates[i]; i++) {
+		for (j = 0; j < *rates_size && rates[j]; j++) {
 			if (rates[j] == card_rates[i])
 				tmp[tmp_size++] = card_rates[i];
 		}
 	}
 
 	lbs_deb_hex(LBS_DEB_JOIN, "AP rates    ", rates, *rates_size);
-	lbs_deb_hex(LBS_DEB_JOIN, "card rates  ", card_rates, num_card_rates);
+	lbs_deb_hex(LBS_DEB_JOIN, "card rates  ", card_rates,
+			ARRAY_SIZE(lbs_bg_rates));
 	lbs_deb_hex(LBS_DEB_JOIN, "common rates", tmp, tmp_size);
 	lbs_deb_join("TX data rate 0x%02x\n", priv->cur_rate);
 
@@ -69,10 +70,7 @@ static int get_common_rates(struct lbs_private *priv,
 		lbs_pr_alert("Previously set fixed data rate %#x isn't "
 		       "compatible with the network.\n", priv->cur_rate);
 		ret = -1;
-		goto done;
 	}
-	ret = 0;
-
 done:
 	memset(rates, 0, *rates_size);
 	*rates_size = min_t(int, tmp_size, *rates_size);
@@ -322,7 +320,7 @@ static int lbs_associate(struct lbs_private *priv,
 	rates = (struct mrvl_ie_rates_param_set *) pos;
 	rates->header.type = cpu_to_le16(TLV_TYPE_RATES);
 	memcpy(&rates->rates, &bss->rates, MAX_RATES);
-	tmplen = MAX_RATES;
+	tmplen = min_t(u16, ARRAY_SIZE(rates->rates), MAX_RATES);
 	if (get_common_rates(priv, rates->rates, &tmplen)) {
 		ret = -1;
 		goto done;
@@ -598,7 +596,7 @@ static int lbs_adhoc_join(struct lbs_private *priv,
 
 	/* Copy Data rates from the rates recorded in scan response */
 	memset(cmd.bss.rates, 0, sizeof(cmd.bss.rates));
-	ratesize = min_t(u16, sizeof(cmd.bss.rates), MAX_RATES);
+	ratesize = min_t(u16, ARRAY_SIZE(cmd.bss.rates), MAX_RATES);
 	memcpy(cmd.bss.rates, bss->rates, ratesize);
 	if (get_common_rates(priv, cmd.bss.rates, &ratesize)) {
 		lbs_deb_join("ADHOC_JOIN: get_common_rates returned error.\n");
-- 
GitLab


From 89c3a8aca28e6d57f2ae945d97858a372d624b81 Mon Sep 17 00:00:00 2001
From: Johannes Berg <johannes@sipsolutions.net>
Date: Tue, 28 Jul 2009 18:10:17 +0200
Subject: [PATCH 0224/1153] mac80211: fix suspend

Jan reported that his b43-based laptop hangs during suspend.
The problem turned out to be mac80211 asking the driver to
stop the hardware before removing interfaces, and interface
removal caused b43 to touch the hardware (while down, which
causes the hang).

This patch fixes mac80211 to do reorder these operations to
have them in the correct order -- first remove interfaces
and then stop the hardware. Some more code is necessary to
be able to do so in a race-free manner, in particular it is
necessary to not process frames received during quiescing.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13337.

Reported-by: Jan Scholz <scholz@fias.uni-frankfurt.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 net/mac80211/pm.c | 24 +++++++++++++++---------
 net/mac80211/rx.c | 12 ++++++++++++
 2 files changed, 27 insertions(+), 9 deletions(-)

diff --git a/net/mac80211/pm.c b/net/mac80211/pm.c
index 7a549f9deb9..5e3d476972f 100644
--- a/net/mac80211/pm.c
+++ b/net/mac80211/pm.c
@@ -55,15 +55,6 @@ int __ieee80211_suspend(struct ieee80211_hw *hw)
 
 	rcu_read_unlock();
 
-	/* flush again, in case driver queued work */
-	flush_workqueue(local->hw.workqueue);
-
-	/* stop hardware - this must stop RX */
-	if (local->open_count) {
-		ieee80211_led_radio(local, false);
-		drv_stop(local);
-	}
-
 	/* remove STAs */
 	spin_lock_irqsave(&local->sta_lock, flags);
 	list_for_each_entry(sta, &local->sta_list, list) {
@@ -111,7 +102,22 @@ int __ieee80211_suspend(struct ieee80211_hw *hw)
 		drv_remove_interface(local, &conf);
 	}
 
+	/* stop hardware - this must stop RX */
+	if (local->open_count) {
+		ieee80211_led_radio(local, false);
+		drv_stop(local);
+	}
+
+	/*
+	 * flush again, in case driver queued work -- it
+	 * shouldn't be doing (or cancel everything in the
+	 * stop callback) that but better safe than sorry.
+	 */
+	flush_workqueue(local->hw.workqueue);
+
 	local->suspended = true;
+	/* need suspended to be visible before quiescing is false */
+	barrier();
 	local->quiescing = false;
 
 	return 0;
diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c
index de5bba7f910..0936fc24942 100644
--- a/net/mac80211/rx.c
+++ b/net/mac80211/rx.c
@@ -2453,6 +2453,18 @@ void __ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb,
 		return;
 	}
 
+	/*
+	 * If we're suspending, it is possible although not too likely
+	 * that we'd be receiving frames after having already partially
+	 * quiesced the stack. We can't process such frames then since
+	 * that might, for example, cause stations to be added or other
+	 * driver callbacks be invoked.
+	 */
+	if (unlikely(local->quiescing || local->suspended)) {
+		kfree_skb(skb);
+		return;
+	}
+
 	if (status->flag & RX_FLAG_HT) {
 		/* rate_idx is MCS index */
 		if (WARN_ON(status->rate_idx < 0 ||
-- 
GitLab


From ec79be26875f6c1468784876cb99192b7f41c7a5 Mon Sep 17 00:00:00 2001
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Wed, 29 Jul 2009 21:07:47 +0200
Subject: [PATCH 0225/1153] PM / ACPI: HP G7000 Notebook needs a SCI_EN resume
 quirk

This fixes regression (battery "vanishing" on resume) introduced by
commit d0c71fe7ebc180f1b7bc7da1d39a07fc19eec768 ("ACPI Suspend: Enable
ACPI during resume if SCI_EN is not set") and also the issue with
the "screaming" IRQ 9.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13745

Reported-and-tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: stable@kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 drivers/acpi/sleep.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/acpi/sleep.c b/drivers/acpi/sleep.c
index 01574a06653..42159a28f43 100644
--- a/drivers/acpi/sleep.c
+++ b/drivers/acpi/sleep.c
@@ -397,6 +397,14 @@ static struct dmi_system_id __initdata acpisleep_dmi_table[] = {
 		},
 	},
 	{
+	.callback = init_set_sci_en_on_resume,
+	.ident = "Hewlett-Packard HP G7000 Notebook PC",
+	.matches = {
+		DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
+		DMI_MATCH(DMI_PRODUCT_NAME, "HP G7000 Notebook PC"),
+		},
+	},
+	{
 	.callback = init_old_suspend_ordering,
 	.ident = "Panasonic CF51-2L",
 	.matches = {
-- 
GitLab


From dddac6a7b445de95515f64fdf82fe5dc36c02f26 Mon Sep 17 00:00:00 2001
From: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Date: Wed, 29 Jul 2009 21:07:55 +0200
Subject: [PATCH 0226/1153] PM / Hibernate: Replace bdget call with simple
 atomic_inc of i_count

Create bdgrab().  This function copies an existing reference to a
block_device.  It is safe to call from any context.

Hibernation code wishes to copy a reference to the active swap device.
Right now it calls bdget() under a spinlock, but this is wrong because
bdget() can sleep.  It doesn't need a full bdget() because we already
hold a reference to active swap devices (and the spinlock protects
against swapoff).

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13827

Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 fs/block_dev.c     | 10 ++++++++++
 include/linux/fs.h |  1 +
 mm/swapfile.c      |  4 ++--
 3 files changed, 13 insertions(+), 2 deletions(-)

diff --git a/fs/block_dev.c b/fs/block_dev.c
index 3a6d4fb2a32..94dfda24c06 100644
--- a/fs/block_dev.c
+++ b/fs/block_dev.c
@@ -564,6 +564,16 @@ struct block_device *bdget(dev_t dev)
 
 EXPORT_SYMBOL(bdget);
 
+/**
+ * bdgrab -- Grab a reference to an already referenced block device
+ * @bdev:	Block device to grab a reference to.
+ */
+struct block_device *bdgrab(struct block_device *bdev)
+{
+	atomic_inc(&bdev->bd_inode->i_count);
+	return bdev;
+}
+
 long nr_blockdev_pages(void)
 {
 	struct block_device *bdev;
diff --git a/include/linux/fs.h b/include/linux/fs.h
index 0872372184f..a36ffa5a77a 100644
--- a/include/linux/fs.h
+++ b/include/linux/fs.h
@@ -1946,6 +1946,7 @@ extern void putname(const char *name);
 extern int register_blkdev(unsigned int, const char *);
 extern void unregister_blkdev(unsigned int, const char *);
 extern struct block_device *bdget(dev_t);
+extern struct block_device *bdgrab(struct block_device *bdev);
 extern void bd_set_size(struct block_device *, loff_t size);
 extern void bd_forget(struct inode *inode);
 extern void bdput(struct block_device *);
diff --git a/mm/swapfile.c b/mm/swapfile.c
index d1ade1a48ee..8ffdc0d23c5 100644
--- a/mm/swapfile.c
+++ b/mm/swapfile.c
@@ -753,7 +753,7 @@ int swap_type_of(dev_t device, sector_t offset, struct block_device **bdev_p)
 
 		if (!bdev) {
 			if (bdev_p)
-				*bdev_p = bdget(sis->bdev->bd_dev);
+				*bdev_p = bdgrab(sis->bdev);
 
 			spin_unlock(&swap_lock);
 			return i;
@@ -765,7 +765,7 @@ int swap_type_of(dev_t device, sector_t offset, struct block_device **bdev_p)
 					struct swap_extent, list);
 			if (se->start_block == offset) {
 				if (bdev_p)
-					*bdev_p = bdget(sis->bdev->bd_dev);
+					*bdev_p = bdgrab(sis->bdev);
 
 				spin_unlock(&swap_lock);
 				bdput(bdev);
-- 
GitLab


From e043e42bdb66885b3ac10d27a01ccb9972e2b0a3 Mon Sep 17 00:00:00 2001
From: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Date: Wed, 29 Jul 2009 12:15:56 -0700
Subject: [PATCH 0227/1153] pty: avoid forcing 'low_latency' tty flag

We really don't want to mark the pty as a low-latency device, because as
Alan points out, the ->write method can be called from an IRQ (ppp?),
and that means we can't use ->low_latency=1 as we take mutexes in the
low_latency case.

So rather than using low_latency to force the written data to be pushed
to the ldisc handling at 'write()' time, just make the reader side (or
the poll function) do the flush when it checks whether there is data to
be had.

This also fixes the problem with lost data in an emacs compile buffer
(bugzilla 13815), and we can thus revert the low_latency pty hack
(commit 3a54297478e6578f96fd54bf4daa1751130aca86: "pty: quickfix for the
pty ENXIO timing problems").

Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[ Modified to do the tty_flush_to_ldisc() inside input_available_p() so
  that it triggers for both read and poll()  - Linus]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/char/n_tty.c      |  1 +
 drivers/char/pty.c        |  2 --
 drivers/char/tty_buffer.c | 13 +++++++++++++
 include/linux/tty.h       |  1 +
 4 files changed, 15 insertions(+), 2 deletions(-)

diff --git a/drivers/char/n_tty.c b/drivers/char/n_tty.c
index ff47907ff1b..973be2f4419 100644
--- a/drivers/char/n_tty.c
+++ b/drivers/char/n_tty.c
@@ -1583,6 +1583,7 @@ static int n_tty_open(struct tty_struct *tty)
 
 static inline int input_available_p(struct tty_struct *tty, int amt)
 {
+	tty_flush_to_ldisc(tty);
 	if (tty->icanon) {
 		if (tty->canon_data)
 			return 1;
diff --git a/drivers/char/pty.c b/drivers/char/pty.c
index 3850a68f265..6e6942c45f5 100644
--- a/drivers/char/pty.c
+++ b/drivers/char/pty.c
@@ -52,7 +52,6 @@ static void pty_close(struct tty_struct *tty, struct file *filp)
 		return;
 	tty->link->packet = 0;
 	set_bit(TTY_OTHER_CLOSED, &tty->link->flags);
-	tty_flip_buffer_push(tty->link);
 	wake_up_interruptible(&tty->link->read_wait);
 	wake_up_interruptible(&tty->link->write_wait);
 	if (tty->driver->subtype == PTY_TYPE_MASTER) {
@@ -208,7 +207,6 @@ static int pty_open(struct tty_struct *tty, struct file *filp)
 	clear_bit(TTY_OTHER_CLOSED, &tty->link->flags);
 	set_bit(TTY_THROTTLED, &tty->flags);
 	retval = 0;
-	tty->low_latency = 1;
 out:
 	return retval;
 }
diff --git a/drivers/char/tty_buffer.c b/drivers/char/tty_buffer.c
index 810ee25d66a..3108991c5c8 100644
--- a/drivers/char/tty_buffer.c
+++ b/drivers/char/tty_buffer.c
@@ -461,6 +461,19 @@ static void flush_to_ldisc(struct work_struct *work)
 	tty_ldisc_deref(disc);
 }
 
+/**
+ *	tty_flush_to_ldisc
+ *	@tty: tty to push
+ *
+ *	Push the terminal flip buffers to the line discipline.
+ *
+ *	Must not be called from IRQ context.
+ */
+void tty_flush_to_ldisc(struct tty_struct *tty)
+{
+	flush_to_ldisc(&tty->buf.work.work);
+}
+
 /**
  *	tty_flip_buffer_push	-	terminal
  *	@tty: tty to push
diff --git a/include/linux/tty.h b/include/linux/tty.h
index 1488d8c81aa..e8c6c9136c9 100644
--- a/include/linux/tty.h
+++ b/include/linux/tty.h
@@ -394,6 +394,7 @@ extern void __do_SAK(struct tty_struct *tty);
 extern void disassociate_ctty(int priv);
 extern void no_tty(void);
 extern void tty_flip_buffer_push(struct tty_struct *tty);
+extern void tty_flush_to_ldisc(struct tty_struct *tty);
 extern void tty_buffer_free_all(struct tty_struct *tty);
 extern void tty_buffer_flush(struct tty_struct *tty);
 extern void tty_buffer_init(struct tty_struct *tty);
-- 
GitLab


From f5886c7f96f2542382d3a983c5f13e03d7fc5259 Mon Sep 17 00:00:00 2001
From: Catalin Marinas <catalin.marinas@arm.com>
Date: Wed, 29 Jul 2009 16:26:57 +0100
Subject: [PATCH 0228/1153] kmemleak: Protect the seq start/next/stop sequence
 by rcu_read_lock()

Objects passed to kmemleak_seq_next() have an incremented reference
count (hence not freed) but they may point via object_list.next to
other freed objects. To avoid this, the whole start/next/stop sequence
must be protected by rcu_read_lock().

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 mm/kmemleak.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/mm/kmemleak.c b/mm/kmemleak.c
index 5aabd41ffb8..487267310a8 100644
--- a/mm/kmemleak.c
+++ b/mm/kmemleak.c
@@ -1217,7 +1217,6 @@ static void *kmemleak_seq_start(struct seq_file *seq, loff_t *pos)
 	}
 	object = NULL;
 out:
-	rcu_read_unlock();
 	return object;
 }
 
@@ -1233,13 +1232,11 @@ static void *kmemleak_seq_next(struct seq_file *seq, void *v, loff_t *pos)
 
 	++(*pos);
 
-	rcu_read_lock();
 	list_for_each_continue_rcu(n, &object_list) {
 		next_obj = list_entry(n, struct kmemleak_object, object_list);
 		if (get_object(next_obj))
 			break;
 	}
-	rcu_read_unlock();
 
 	put_object(prev_obj);
 	return next_obj;
@@ -1255,6 +1252,7 @@ static void kmemleak_seq_stop(struct seq_file *seq, void *v)
 		 * kmemleak_seq_start may return ERR_PTR if the scan_mutex
 		 * waiting was interrupted, so only release it if !IS_ERR.
 		 */
+		rcu_read_unlock();
 		mutex_unlock(&scan_mutex);
 		if (v)
 			put_object(v);
-- 
GitLab


From cdaa052b05e26d96a990af5d253fd2af5db2b1fc Mon Sep 17 00:00:00 2001
From: Zhao Yakui <yakui.zhao@intel.com>
Date: Tue, 28 Jul 2009 10:54:13 +0800
Subject: [PATCH 0229/1153] drm/I915: Fix offset to DVO timings in LVDS data

Now the DVO timing in LVDS data entry is obtained by using the
following step:
    a. get the entry size for every LVDS panel data
    b. Get the LVDS fp entry for the preferred panel type
    c. get the DVO timing by using entry->dvo_timing

In our driver the entry->dvo_timing is related with the size of
lvds_fp_timing. For example: the size is 46.

But it seems that the size of lvds_fp_timing varies on the differnt
platform. In such case we will get the incorrect DVO timing entry
because of the incorrect DVO offset in LVDS panel data entry.
This also removes a hack on new IGDNG to get proper DVO timing.

Calculate the DVO timing offset in LVDS data entry to get the DVO timing
    a. get the DVO timing offset in the LVDS fp data entry by using the
pointer definition in LVDS data ptr
    b. get the LVDS data entry
    c. get the DVO timing by adding the DVO timing offset to data entry

https://bugs.freedesktop.org/show_bug.cgi?id=22787

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_bios.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_bios.c b/drivers/gpu/drm/i915/intel_bios.c
index 7cc44719102..5c7a62a96ae 100644
--- a/drivers/gpu/drm/i915/intel_bios.c
+++ b/drivers/gpu/drm/i915/intel_bios.c
@@ -97,14 +97,13 @@ static void
 parse_lfp_panel_data(struct drm_i915_private *dev_priv,
 			    struct bdb_header *bdb)
 {
-	struct drm_device *dev = dev_priv->dev;
 	struct bdb_lvds_options *lvds_options;
 	struct bdb_lvds_lfp_data *lvds_lfp_data;
 	struct bdb_lvds_lfp_data_ptrs *lvds_lfp_data_ptrs;
 	struct bdb_lvds_lfp_data_entry *entry;
 	struct lvds_dvo_timing *dvo_timing;
 	struct drm_display_mode *panel_fixed_mode;
-	int lfp_data_size;
+	int lfp_data_size, dvo_timing_offset;
 
 	/* Defaults if we can't find VBT info */
 	dev_priv->lvds_dither = 0;
@@ -133,14 +132,16 @@ parse_lfp_panel_data(struct drm_i915_private *dev_priv,
 	entry = (struct bdb_lvds_lfp_data_entry *)
 		((uint8_t *)lvds_lfp_data->data + (lfp_data_size *
 						   lvds_options->panel_type));
+	dvo_timing_offset = lvds_lfp_data_ptrs->ptr[0].dvo_timing_offset -
+		lvds_lfp_data_ptrs->ptr[0].fp_timing_offset;
 
-	/* On IGDNG mobile, LVDS data block removes panel fitting registers.
-	   So dec 2 dword from dvo_timing offset */
-	if (IS_IGDNG(dev))
-		dvo_timing = (struct lvds_dvo_timing *)
-					((u8 *)&entry->dvo_timing - 8);
-	else
-		dvo_timing = &entry->dvo_timing;
+	/*
+	 * the size of fp_timing varies on the different platform.
+	 * So calculate the DVO timing relative offset in LVDS data
+	 * entry to get the DVO timing entry
+	 */
+	dvo_timing = (struct lvds_dvo_timing *)
+			((unsigned char *)entry + dvo_timing_offset);
 
 	panel_fixed_mode = kzalloc(sizeof(*panel_fixed_mode), GFP_KERNEL);
 
-- 
GitLab


From 24f119c769bacac5729297b682fec7811a983cc6 Mon Sep 17 00:00:00 2001
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Fri, 24 Jul 2009 01:00:28 +0800
Subject: [PATCH 0230/1153] drm/i915: disable VGA plane reliably

This does VGA disable like DDX driver. SR01 bit 5 should be set
before VGA plane disable through control register, otherwise we
might get random crash and lockups.

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_display.c | 28 +++++++++++++++++++++++++---
 1 file changed, 25 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index a58bfadabd6..b06364ed259 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -998,6 +998,29 @@ intel_pipe_set_base(struct drm_crtc *crtc, int x, int y,
 	return 0;
 }
 
+/* Disable the VGA plane that we never use */
+static void i915_disable_vga (struct drm_device *dev)
+{
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	u8 sr1;
+	u32 vga_reg;
+
+	if (IS_IGDNG(dev))
+		vga_reg = CPU_VGACNTRL;
+	else
+		vga_reg = VGACNTRL;
+
+	if (I915_READ(vga_reg) & VGA_DISP_DISABLE)
+		return;
+
+	I915_WRITE8(VGA_SR_INDEX, 1);
+	sr1 = I915_READ8(VGA_SR_DATA);
+	I915_WRITE8(VGA_SR_DATA, sr1 | (1 << 5));
+	udelay(100);
+
+	I915_WRITE(vga_reg, VGA_DISP_DISABLE);
+}
+
 static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 {
 	struct drm_device *dev = crtc->dev;
@@ -1200,8 +1223,7 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 	case DRM_MODE_DPMS_OFF:
 		DRM_DEBUG("crtc %d dpms off\n", pipe);
 
-		/* Disable the VGA plane that we never use */
-		I915_WRITE(CPU_VGACNTRL, VGA_DISP_DISABLE);
+		i915_disable_vga(dev);
 
 		/* Disable display plane */
 		temp = I915_READ(dspcntr_reg);
@@ -1342,7 +1364,7 @@ static void i9xx_crtc_dpms(struct drm_crtc *crtc, int mode)
 		//intel_crtc_dpms_video(crtc, FALSE); TODO
 
 		/* Disable the VGA plane that we never use */
-		I915_WRITE(VGACNTRL, VGA_DISP_DISABLE);
+		i915_disable_vga(dev);
 
 		/* Disable display plane */
 		temp = I915_READ(dspcntr_reg);
-- 
GitLab


From 249c0e64c24bf455a4e4815f72750f2b16cedd94 Mon Sep 17 00:00:00 2001
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Fri, 24 Jul 2009 01:00:29 +0800
Subject: [PATCH 0231/1153] drm/i915: fix issue in display pipe setup on IGDNG

During pipe DPMS off, instead of busy waiting pipe off, insert
delays during wait and don't loop after enough tries which matches
spec requirement. Also try to match DPMS on path by disable FDI TX
PLL in DPMS off. Disable PF by writing PF_WIN_SZ which really trigger
the update.

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/i915_reg.h      |  2 +
 drivers/gpu/drm/i915/intel_display.c | 56 ++++++++++++++++++++++------
 2 files changed, 46 insertions(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 897a116cad1..7c77c4c53c5 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -1848,6 +1848,8 @@
 #define PFA_CTL_1               0x68080
 #define PFB_CTL_1               0x68880
 #define  PF_ENABLE              (1<<31)
+#define PFA_WIN_SZ		0x68074
+#define PFB_WIN_SZ		0x68874
 
 /* legacy palette */
 #define LGC_PALETTE_A           0x4a000
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index b06364ed259..15a8c3908ac 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -1038,6 +1038,7 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 	int fdi_rx_imr_reg = (pipe == 0) ? FDI_RXA_IMR : FDI_RXB_IMR;
 	int transconf_reg = (pipe == 0) ? TRANSACONF : TRANSBCONF;
 	int pf_ctl_reg = (pipe == 0) ? PFA_CTL_1 : PFB_CTL_1;
+	int pf_win_size = (pipe == 0) ? PFA_WIN_SZ : PFB_WIN_SZ;
 	int cpu_htot_reg = (pipe == 0) ? HTOTAL_A : HTOTAL_B;
 	int cpu_hblank_reg = (pipe == 0) ? HBLANK_A : HBLANK_B;
 	int cpu_hsync_reg = (pipe == 0) ? HSYNC_A : HSYNC_B;
@@ -1051,7 +1052,7 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 	int trans_vblank_reg = (pipe == 0) ? TRANS_VBLANK_A : TRANS_VBLANK_B;
 	int trans_vsync_reg = (pipe == 0) ? TRANS_VSYNC_A : TRANS_VSYNC_B;
 	u32 temp;
-	int tries = 5, j;
+	int tries = 5, j, n;
 
 	/* XXX: When our outputs are all unaware of DPMS modes other than off
 	 * and on, we should map those modes to DRM_MODE_DPMS_OFF in the CRTC.
@@ -1239,19 +1240,21 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 		if ((temp & PIPEACONF_ENABLE) != 0) {
 			I915_WRITE(pipeconf_reg, temp & ~PIPEACONF_ENABLE);
 			I915_READ(pipeconf_reg);
+			n = 0;
 			/* wait for cpu pipe off, pipe state */
-			while ((I915_READ(pipeconf_reg) & I965_PIPECONF_ACTIVE) != 0)
-				;
+			while ((I915_READ(pipeconf_reg) & I965_PIPECONF_ACTIVE) != 0) {
+				n++;
+				if (n < 60) {
+					udelay(500);
+					continue;
+				} else {
+					DRM_DEBUG("pipe %d off delay\n", pipe);
+					break;
+				}
+			}
 		} else
 			DRM_DEBUG("crtc %d is disabled\n", pipe);
 
-		/* IGDNG-A : disable cpu panel fitter ? */
-		temp = I915_READ(pf_ctl_reg);
-		if ((temp & PF_ENABLE) != 0) {
-			I915_WRITE(pf_ctl_reg, temp & ~PF_ENABLE);
-			I915_READ(pf_ctl_reg);
-		}
-
 		/* disable CPU FDI tx and PCH FDI rx */
 		temp = I915_READ(fdi_tx_reg);
 		I915_WRITE(fdi_tx_reg, temp & ~FDI_TX_ENABLE);
@@ -1261,6 +1264,8 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 		I915_WRITE(fdi_rx_reg, temp & ~FDI_RX_ENABLE);
 		I915_READ(fdi_rx_reg);
 
+		udelay(100);
+
 		/* still set train pattern 1 */
 		temp = I915_READ(fdi_tx_reg);
 		temp &= ~FDI_LINK_TRAIN_NONE;
@@ -1272,14 +1277,25 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 		temp |= FDI_LINK_TRAIN_PATTERN_1;
 		I915_WRITE(fdi_rx_reg, temp);
 
+		udelay(100);
+
 		/* disable PCH transcoder */
 		temp = I915_READ(transconf_reg);
 		if ((temp & TRANS_ENABLE) != 0) {
 			I915_WRITE(transconf_reg, temp & ~TRANS_ENABLE);
 			I915_READ(transconf_reg);
+			n = 0;
 			/* wait for PCH transcoder off, transcoder state */
-			while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) != 0)
-				;
+			while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) != 0) {
+				n++;
+				if (n < 60) {
+					udelay(500);
+					continue;
+				} else {
+					DRM_DEBUG("transcoder %d off delay\n", pipe);
+					break;
+				}
+			}
 		}
 
 		/* disable PCH DPLL */
@@ -1297,6 +1313,22 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 			I915_READ(fdi_rx_reg);
 		}
 
+		/* Disable CPU FDI TX PLL */
+		temp = I915_READ(fdi_tx_reg);
+		if ((temp & FDI_TX_PLL_ENABLE) != 0) {
+			I915_WRITE(fdi_tx_reg, temp & ~FDI_TX_PLL_ENABLE);
+			I915_READ(fdi_tx_reg);
+			udelay(100);
+		}
+
+		/* Disable PF */
+		temp = I915_READ(pf_ctl_reg);
+		if ((temp & PF_ENABLE) != 0) {
+			I915_WRITE(pf_ctl_reg, temp & ~PF_ENABLE);
+			I915_READ(pf_ctl_reg);
+		}
+		I915_WRITE(pf_win_size, 0);
+
 		/* Wait for the clocks to turn off. */
 		udelay(150);
 		break;
-- 
GitLab


From eebc863e469cd91d96c4e3636450596ae29f0502 Mon Sep 17 00:00:00 2001
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Fri, 24 Jul 2009 01:00:30 +0800
Subject: [PATCH 0232/1153] drm/i915: Fix channel ending action for DP aux
 transaction

We should use current channel 'status' bits to clear DP aux channel's
done and error bits, instead of using the channel setting bits, that
will set send/busy bit again to initiate new transaction.

This also includes also some minor cleanup.

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_dp.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 6770ae88370..afec65c5ad8 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -236,7 +236,7 @@ intel_dp_aux_ch(struct intel_output *intel_output,
 		}
 	
 		/* Clear done status and any errors */
-		I915_WRITE(ch_ctl, (ctl |
+		I915_WRITE(ch_ctl, (status |
 				DP_AUX_CH_CTL_DONE |
 				DP_AUX_CH_CTL_TIME_OUT_ERROR |
 				DP_AUX_CH_CTL_RECEIVE_ERROR));
@@ -295,7 +295,7 @@ intel_dp_aux_native_write(struct intel_output *intel_output,
 		return -1;
 	msg[0] = AUX_NATIVE_WRITE << 4;
 	msg[1] = address >> 8;
-	msg[2] = address;
+	msg[2] = address & 0xff;
 	msg[3] = send_bytes - 1;
 	memcpy(&msg[4], send, send_bytes);
 	msg_bytes = send_bytes + 4;
@@ -387,8 +387,8 @@ intel_dp_i2c_init(struct intel_output *intel_output, const char *name)
 	memset(&dp_priv->adapter, '\0', sizeof (dp_priv->adapter));
 	dp_priv->adapter.owner = THIS_MODULE;
 	dp_priv->adapter.class = I2C_CLASS_DDC;
-	strncpy (dp_priv->adapter.name, name, sizeof dp_priv->adapter.name - 1);
-	dp_priv->adapter.name[sizeof dp_priv->adapter.name - 1] = '\0';
+	strncpy (dp_priv->adapter.name, name, sizeof(dp_priv->adapter.name) - 1);
+	dp_priv->adapter.name[sizeof(dp_priv->adapter.name) - 1] = '\0';
 	dp_priv->adapter.algo_data = &dp_priv->algo;
 	dp_priv->adapter.dev.parent = &intel_output->base.kdev;
 	
-- 
GitLab


From 5eb08b69f510fadaba77eb9a1bda0f7299c4ebcc Mon Sep 17 00:00:00 2001
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Fri, 24 Jul 2009 01:00:31 +0800
Subject: [PATCH 0233/1153] drm/i915: enable DisplayPort support on IGDNG

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/i915_reg.h      |  25 +++++++
 drivers/gpu/drm/i915/intel_display.c |  51 +++++++++++++-
 drivers/gpu/drm/i915/intel_dp.c      | 102 ++++++++++++++++++++++-----
 3 files changed, 157 insertions(+), 21 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 7c77c4c53c5..4518a9489ed 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -1444,6 +1444,7 @@
 #define   DP_CLOCK_OUTPUT_ENABLE	(1 << 13)
 
 #define   DP_SCRAMBLING_DISABLE		(1 << 12)
+#define   DP_SCRAMBLING_DISABLE_IGDNG	(1 << 7)
 
 /** limit RGB values to avoid confusing TVs */
 #define   DP_COLOR_RANGE_16_235		(1 << 8)
@@ -2210,4 +2211,28 @@
 #define PCH_PP_OFF_DELAYS	0xc720c
 #define PCH_PP_DIVISOR		0xc7210
 
+#define PCH_DP_B		0xe4100
+#define PCH_DPB_AUX_CH_CTL	0xe4110
+#define PCH_DPB_AUX_CH_DATA1	0xe4114
+#define PCH_DPB_AUX_CH_DATA2	0xe4118
+#define PCH_DPB_AUX_CH_DATA3	0xe411c
+#define PCH_DPB_AUX_CH_DATA4	0xe4120
+#define PCH_DPB_AUX_CH_DATA5	0xe4124
+
+#define PCH_DP_C		0xe4200
+#define PCH_DPC_AUX_CH_CTL	0xe4210
+#define PCH_DPC_AUX_CH_DATA1	0xe4214
+#define PCH_DPC_AUX_CH_DATA2	0xe4218
+#define PCH_DPC_AUX_CH_DATA3	0xe421c
+#define PCH_DPC_AUX_CH_DATA4	0xe4220
+#define PCH_DPC_AUX_CH_DATA5	0xe4224
+
+#define PCH_DP_D		0xe4300
+#define PCH_DPD_AUX_CH_CTL	0xe4310
+#define PCH_DPD_AUX_CH_DATA1	0xe4314
+#define PCH_DPD_AUX_CH_DATA2	0xe4318
+#define PCH_DPD_AUX_CH_DATA3	0xe431c
+#define PCH_DPD_AUX_CH_DATA4	0xe4320
+#define PCH_DPD_AUX_CH_DATA5	0xe4324
+
 #endif /* _I915_REG_H_ */
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 15a8c3908ac..34c50460eaa 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -268,6 +268,9 @@ intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
 static bool
 intel_find_pll_g4x_dp(const intel_limit_t *, struct drm_crtc *crtc,
 		      int target, int refclk, intel_clock_t *best_clock);
+static bool
+intel_find_pll_igdng_dp(const intel_limit_t *, struct drm_crtc *crtc,
+		      int target, int refclk, intel_clock_t *best_clock);
 
 static const intel_limit_t intel_limits_i8xx_dvo = {
         .dot = { .min = I8XX_DOT_MIN,		.max = I8XX_DOT_MAX },
@@ -751,6 +754,30 @@ intel_g4x_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
 	return found;
 }
 
+static bool
+intel_find_pll_igdng_dp(const intel_limit_t *limit, struct drm_crtc *crtc,
+		      int target, int refclk, intel_clock_t *best_clock)
+{
+	struct drm_device *dev = crtc->dev;
+	intel_clock_t clock;
+	if (target < 200000) {
+		clock.n = 1;
+		clock.p1 = 2;
+		clock.p2 = 10;
+		clock.m1 = 12;
+		clock.m2 = 9;
+	} else {
+		clock.n = 2;
+		clock.p1 = 1;
+		clock.p2 = 10;
+		clock.m1 = 14;
+		clock.m2 = 8;
+	}
+	intel_clock(dev, refclk, &clock);
+	memcpy(best_clock, &clock, sizeof(intel_clock_t));
+	return true;
+}
+
 static bool
 intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
 			int target, int refclk, intel_clock_t *best_clock)
@@ -763,6 +790,10 @@ intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
 	int err_most = 47;
 	found = false;
 
+	if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT))
+		return intel_find_pll_igdng_dp(limit, crtc, target,
+					       refclk, best_clock);
+
 	if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) {
 		if ((I915_READ(LVDS) & LVDS_CLKB_POWER_MASK) ==
 		    LVDS_CLKB_POWER_UP)
@@ -2136,6 +2167,7 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 	int lvds_reg = LVDS;
 	u32 temp;
 	int sdvo_pixel_multiply;
+	int target_clock;
 
 	drm_vblank_pre_modeset(dev, pipe);
 
@@ -2218,11 +2250,18 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 	}
 
 	/* FDI link */
-	if (IS_IGDNG(dev))
+	if (IS_IGDNG(dev)) {
+		/* DP over FDI requires target mode clock
+		   instead of link clock */
+		if (is_dp)
+			target_clock = mode->clock;
+		else
+			target_clock = adjusted_mode->clock;
 		igdng_compute_m_n(3, 4, /* lane num 4 */
-				adjusted_mode->clock,
+				target_clock,
 				270000, /* lane clock */
 				&m_n);
+	}
 
 	if (IS_IGD(dev))
 		fp = (1 << clock.n) << 16 | clock.m1 << 8 | clock.m2;
@@ -3050,6 +3089,8 @@ static void intel_setup_outputs(struct drm_device *dev)
 			found = 0;
 			if (!found)
 				intel_hdmi_init(dev, HDMIB);
+			if (!found && (I915_READ(PCH_DP_B) & DP_DETECTED))
+				intel_dp_init(dev, PCH_DP_B);
 		}
 
 		if (I915_READ(HDMIC) & PORT_DETECTED)
@@ -3058,6 +3099,12 @@ static void intel_setup_outputs(struct drm_device *dev)
 		if (I915_READ(HDMID) & PORT_DETECTED)
 			intel_hdmi_init(dev, HDMID);
 
+		if (I915_READ(PCH_DP_C) & DP_DETECTED)
+			intel_dp_init(dev, PCH_DP_C);
+
+		if (I915_READ(PCH_DP_D) & DP_DETECTED)
+			intel_dp_init(dev, PCH_DP_D);
+
 	} else if (IS_I9XX(dev)) {
 		int found;
 		u32 reg;
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index afec65c5ad8..0715911cbd8 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -206,7 +206,12 @@ intel_dp_aux_ch(struct intel_output *intel_output,
 	 * and would like to run at 2MHz. So, take the
 	 * hrawclk value and divide by 2 and use that
 	 */
-	aux_clock_divider = intel_hrawclk(dev) / 2;
+	/* IGDNG: input clock fixed at 125Mhz, so aux_bit_clk always 62 */
+	if (IS_IGDNG(dev))
+		aux_clock_divider = 62;
+	else
+		aux_clock_divider = intel_hrawclk(dev) / 2;
+
 	/* Must try at least 3 times according to DP spec */
 	for (try = 0; try < 5; try++) {
 		/* Load the send data into the aux channel data registers */
@@ -493,22 +498,40 @@ intel_dp_set_m_n(struct drm_crtc *crtc, struct drm_display_mode *mode,
 	intel_dp_compute_m_n(3, lane_count,
 			     mode->clock, adjusted_mode->clock, &m_n);
 
-	if (intel_crtc->pipe == 0) {
-		I915_WRITE(PIPEA_GMCH_DATA_M,
-		       ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) |
-		       m_n.gmch_m);
-		I915_WRITE(PIPEA_GMCH_DATA_N,
-		       m_n.gmch_n);
-		I915_WRITE(PIPEA_DP_LINK_M, m_n.link_m);
-		I915_WRITE(PIPEA_DP_LINK_N, m_n.link_n);
+	if (IS_IGDNG(dev)) {
+		if (intel_crtc->pipe == 0) {
+			I915_WRITE(TRANSA_DATA_M1,
+				   ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) |
+				   m_n.gmch_m);
+			I915_WRITE(TRANSA_DATA_N1, m_n.gmch_n);
+			I915_WRITE(TRANSA_DP_LINK_M1, m_n.link_m);
+			I915_WRITE(TRANSA_DP_LINK_N1, m_n.link_n);
+		} else {
+			I915_WRITE(TRANSB_DATA_M1,
+				   ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) |
+				   m_n.gmch_m);
+			I915_WRITE(TRANSB_DATA_N1, m_n.gmch_n);
+			I915_WRITE(TRANSB_DP_LINK_M1, m_n.link_m);
+			I915_WRITE(TRANSB_DP_LINK_N1, m_n.link_n);
+		}
 	} else {
-		I915_WRITE(PIPEB_GMCH_DATA_M,
-		       ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) |
-		       m_n.gmch_m);
-		I915_WRITE(PIPEB_GMCH_DATA_N,
-		       m_n.gmch_n);
-		I915_WRITE(PIPEB_DP_LINK_M, m_n.link_m);
-		I915_WRITE(PIPEB_DP_LINK_N, m_n.link_n);
+		if (intel_crtc->pipe == 0) {
+			I915_WRITE(PIPEA_GMCH_DATA_M,
+				   ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) |
+				   m_n.gmch_m);
+			I915_WRITE(PIPEA_GMCH_DATA_N,
+				   m_n.gmch_n);
+			I915_WRITE(PIPEA_DP_LINK_M, m_n.link_m);
+			I915_WRITE(PIPEA_DP_LINK_N, m_n.link_n);
+		} else {
+			I915_WRITE(PIPEB_GMCH_DATA_M,
+				   ((m_n.tu - 1) << PIPE_GMCH_DATA_M_TU_SIZE_SHIFT) |
+				   m_n.gmch_m);
+			I915_WRITE(PIPEB_GMCH_DATA_N,
+					m_n.gmch_n);
+			I915_WRITE(PIPEB_DP_LINK_M, m_n.link_m);
+			I915_WRITE(PIPEB_DP_LINK_N, m_n.link_n);
+		}
 	}
 }
 
@@ -935,6 +958,12 @@ intel_dp_link_down(struct intel_output *intel_output, uint32_t DP)
 	struct drm_i915_private *dev_priv = dev->dev_private;
 	struct intel_dp_priv *dp_priv = intel_output->dev_priv;
 
+	DP &= ~DP_LINK_TRAIN_MASK;
+	I915_WRITE(dp_priv->output_reg, DP | DP_LINK_TRAIN_PAT_IDLE);
+	POSTING_READ(dp_priv->output_reg);
+
+	udelay(17000);
+
 	I915_WRITE(dp_priv->output_reg, DP & ~DP_PORT_EN);
 	POSTING_READ(dp_priv->output_reg);
 }
@@ -978,6 +1007,24 @@ intel_dp_check_link_status(struct intel_output *intel_output)
 		intel_dp_link_train(intel_output, dp_priv->DP, dp_priv->link_configuration);
 }
 
+static enum drm_connector_status
+igdng_dp_detect(struct drm_connector *connector)
+{
+	struct intel_output *intel_output = to_intel_output(connector);
+	struct intel_dp_priv *dp_priv = intel_output->dev_priv;
+	enum drm_connector_status status;
+
+	status = connector_status_disconnected;
+	if (intel_dp_aux_native_read(intel_output,
+				     0x000, dp_priv->dpcd,
+				     sizeof (dp_priv->dpcd)) == sizeof (dp_priv->dpcd))
+	{
+		if (dp_priv->dpcd[0] != 0)
+			status = connector_status_connected;
+	}
+	return status;
+}
+
 /**
  * Uses CRT_HOTPLUG_EN and CRT_HOTPLUG_STAT to detect DP connection.
  *
@@ -996,6 +1043,9 @@ intel_dp_detect(struct drm_connector *connector)
 
 	dp_priv->has_audio = false;
 
+	if (IS_IGDNG(dev))
+		return igdng_dp_detect(connector);
+
 	temp = I915_READ(PORT_HOTPLUG_EN);
 
 	I915_WRITE(PORT_HOTPLUG_EN,
@@ -1106,6 +1156,7 @@ intel_dp_init(struct drm_device *dev, int output_reg)
 	struct drm_connector *connector;
 	struct intel_output *intel_output;
 	struct intel_dp_priv *dp_priv;
+	const char *name = NULL;
 
 	intel_output = kcalloc(sizeof(struct intel_output) + 
 			       sizeof(struct intel_dp_priv), 1, GFP_KERNEL);
@@ -1139,9 +1190,22 @@ intel_dp_init(struct drm_device *dev, int output_reg)
 	drm_sysfs_connector_add(connector);
 
 	/* Set up the DDC bus. */
-	intel_dp_i2c_init(intel_output,
-			  (output_reg == DP_B) ? "DPDDC-B" :
-			  (output_reg == DP_C) ? "DPDDC-C" : "DPDDC-D");
+	switch (output_reg) {
+		case DP_B:
+		case PCH_DP_B:
+			name = "DPDDC-B";
+			break;
+		case DP_C:
+		case PCH_DP_C:
+			name = "DPDDC-C";
+			break;
+		case DP_D:
+		case PCH_DP_D:
+			name = "DPDDC-D";
+			break;
+	}
+
+	intel_dp_i2c_init(intel_output, name);
 	intel_output->ddc_bus = &dp_priv->adapter;
 	intel_output->hot_plug = intel_dp_hot_plug;
 
-- 
GitLab


From 32f9d658aee5be09ebdd28fc730630e61d0b46db Mon Sep 17 00:00:00 2001
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Fri, 24 Jul 2009 01:00:32 +0800
Subject: [PATCH 0234/1153] drm/i915: Add eDP support on IGDNG mobile chip

This adds embedded DisplayPort support on next mobile chip which
aims to replace origin LVDS port. VBT's driver feature block has
been used to determine the type of current internal panel for eDP
or LVDS.

Currently no panel fitting support for eDP and backlight control
would be added in future.

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/i915_drv.h      |   2 +
 drivers/gpu/drm/i915/i915_reg.h      |  16 +
 drivers/gpu/drm/i915/intel_bios.c    |  21 ++
 drivers/gpu/drm/i915/intel_bios.h    |  45 +++
 drivers/gpu/drm/i915/intel_display.c | 433 +++++++++++++++++----------
 drivers/gpu/drm/i915/intel_dp.c      | 112 ++++++-
 drivers/gpu/drm/i915/intel_drv.h     |   3 +
 drivers/gpu/drm/i915/intel_lvds.c    |   4 +
 8 files changed, 468 insertions(+), 168 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index b05b44dd3bf..5f3a259d95e 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -219,6 +219,7 @@ typedef struct drm_i915_private {
 	unsigned int lvds_vbt:1;
 	unsigned int int_crt_support:1;
 	unsigned int lvds_use_ssc:1;
+	unsigned int edp_support:1;
 	int lvds_ssc_freq;
 
 	struct drm_i915_fence_reg fence_regs[16]; /* assume 965 */
@@ -889,6 +890,7 @@ extern int i915_wait_ring(struct drm_device * dev, int n, const char *caller);
 						      IS_I915GM(dev)))
 #define SUPPORTS_INTEGRATED_HDMI(dev)	(IS_G4X(dev) || IS_IGDNG(dev))
 #define SUPPORTS_INTEGRATED_DP(dev)	(IS_G4X(dev) || IS_IGDNG(dev))
+#define SUPPORTS_EDP(dev)		(IS_IGDNG_M(dev))
 #define I915_HAS_HOTPLUG(dev) (IS_I945G(dev) || IS_I945GM(dev) || IS_I965G(dev))
 /* dsparb controlled by hw only */
 #define DSPARB_HWCONTROL(dev) (IS_G4X(dev) || IS_IGDNG(dev))
diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index 4518a9489ed..2955083aa47 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -1395,6 +1395,7 @@
 #define TV_V_CHROMA_42		0x684a8
 
 /* Display Port */
+#define DP_A				0x64000 /* eDP */
 #define DP_B				0x64100
 #define DP_C				0x64200
 #define DP_D				0x64300
@@ -1437,9 +1438,17 @@
 /* Mystic DPCD version 1.1 special mode */
 #define   DP_ENHANCED_FRAMING		(1 << 18)
 
+/* eDP */
+#define   DP_PLL_FREQ_270MHZ		(0 << 16)
+#define   DP_PLL_FREQ_160MHZ		(1 << 16)
+#define   DP_PLL_FREQ_MASK		(3 << 16)
+
 /** locked once port is enabled */
 #define   DP_PORT_REVERSAL		(1 << 15)
 
+/* eDP */
+#define   DP_PLL_ENABLE			(1 << 14)
+
 /** sends the clock on lane 15 of the PEG for debug */
 #define   DP_CLOCK_OUTPUT_ENABLE	(1 << 13)
 
@@ -1464,6 +1473,13 @@
  * is 20 bytes in each direction, hence the 5 fixed
  * data registers
  */
+#define DPA_AUX_CH_CTL			0x64010
+#define DPA_AUX_CH_DATA1		0x64014
+#define DPA_AUX_CH_DATA2		0x64018
+#define DPA_AUX_CH_DATA3		0x6401c
+#define DPA_AUX_CH_DATA4		0x64020
+#define DPA_AUX_CH_DATA5		0x64024
+
 #define DPB_AUX_CH_CTL			0x64110
 #define DPB_AUX_CH_DATA1		0x64114
 #define DPB_AUX_CH_DATA2		0x64118
diff --git a/drivers/gpu/drm/i915/intel_bios.c b/drivers/gpu/drm/i915/intel_bios.c
index 5c7a62a96ae..300aee3296c 100644
--- a/drivers/gpu/drm/i915/intel_bios.c
+++ b/drivers/gpu/drm/i915/intel_bios.c
@@ -296,6 +296,25 @@ parse_sdvo_device_mapping(struct drm_i915_private *dev_priv,
 	}
 	return;
 }
+
+static void
+parse_driver_features(struct drm_i915_private *dev_priv,
+		       struct bdb_header *bdb)
+{
+	struct drm_device *dev = dev_priv->dev;
+	struct bdb_driver_features *driver;
+
+	/* set default for chips without eDP */
+	if (!SUPPORTS_EDP(dev)) {
+		dev_priv->edp_support = 0;
+		return;
+	}
+
+	driver = find_section(bdb, BDB_DRIVER_FEATURES);
+	if (driver && driver->lvds_config == BDB_DRIVER_FEATURE_EDP)
+		dev_priv->edp_support = 1;
+}
+
 /**
  * intel_init_bios - initialize VBIOS settings & find VBT
  * @dev: DRM device
@@ -346,6 +365,8 @@ intel_init_bios(struct drm_device *dev)
 	parse_lfp_panel_data(dev_priv, bdb);
 	parse_sdvo_panel_data(dev_priv, bdb);
 	parse_sdvo_device_mapping(dev_priv, bdb);
+	parse_driver_features(dev_priv, bdb);
+
 	pci_unmap_rom(pdev, bios);
 
 	return 0;
diff --git a/drivers/gpu/drm/i915/intel_bios.h b/drivers/gpu/drm/i915/intel_bios.h
index fe72e1c225d..0f8e5f69ac7 100644
--- a/drivers/gpu/drm/i915/intel_bios.h
+++ b/drivers/gpu/drm/i915/intel_bios.h
@@ -381,6 +381,51 @@ struct bdb_sdvo_lvds_options {
 } __attribute__((packed));
 
 
+#define BDB_DRIVER_FEATURE_NO_LVDS		0
+#define BDB_DRIVER_FEATURE_INT_LVDS		1
+#define BDB_DRIVER_FEATURE_SDVO_LVDS		2
+#define BDB_DRIVER_FEATURE_EDP			3
+
+struct bdb_driver_features {
+	u8 boot_dev_algorithm:1;
+	u8 block_display_switch:1;
+	u8 allow_display_switch:1;
+	u8 hotplug_dvo:1;
+	u8 dual_view_zoom:1;
+	u8 int15h_hook:1;
+	u8 sprite_in_clone:1;
+	u8 primary_lfp_id:1;
+
+	u16 boot_mode_x;
+	u16 boot_mode_y;
+	u8 boot_mode_bpp;
+	u8 boot_mode_refresh;
+
+	u16 enable_lfp_primary:1;
+	u16 selective_mode_pruning:1;
+	u16 dual_frequency:1;
+	u16 render_clock_freq:1; /* 0: high freq; 1: low freq */
+	u16 nt_clone_support:1;
+	u16 power_scheme_ui:1; /* 0: CUI; 1: 3rd party */
+	u16 sprite_display_assign:1; /* 0: secondary; 1: primary */
+	u16 cui_aspect_scaling:1;
+	u16 preserve_aspect_ratio:1;
+	u16 sdvo_device_power_down:1;
+	u16 crt_hotplug:1;
+	u16 lvds_config:2;
+	u16 tv_hotplug:1;
+	u16 hdmi_config:2;
+
+	u8 static_display:1;
+	u8 reserved2:7;
+	u16 legacy_crt_max_x;
+	u16 legacy_crt_max_y;
+	u8 legacy_crt_max_refresh;
+
+	u8 hdmi_termination;
+	u8 custom_vbt_version;
+} __attribute__((packed));
+
 bool intel_init_bios(struct drm_device *dev);
 
 /*
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 34c50460eaa..a9f1307d32d 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -34,6 +34,8 @@
 
 #include "drm_crtc_helper.h"
 
+#define HAS_eDP (intel_pipe_has_type(crtc, INTEL_OUTPUT_EDP))
+
 bool intel_pipe_has_type (struct drm_crtc *crtc, int type);
 static void intel_update_watermarks(struct drm_device *dev);
 
@@ -601,6 +603,23 @@ bool intel_pipe_has_type (struct drm_crtc *crtc, int type)
     return false;
 }
 
+struct drm_connector *
+intel_pipe_get_output (struct drm_crtc *crtc)
+{
+    struct drm_device *dev = crtc->dev;
+    struct drm_mode_config *mode_config = &dev->mode_config;
+    struct drm_connector *l_entry, *ret = NULL;
+
+    list_for_each_entry(l_entry, &mode_config->connector_list, head) {
+	    if (l_entry->encoder &&
+	        l_entry->encoder->crtc == crtc) {
+		    ret = l_entry;
+		    break;
+	    }
+    }
+    return ret;
+}
+
 #define INTELPllInvalid(s)   do { /* DRM_DEBUG(s); */ return false; } while (0)
 /**
  * Returns whether the given set of divisors are valid for a given refclk with
@@ -790,6 +809,10 @@ intel_igdng_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
 	int err_most = 47;
 	found = false;
 
+	/* eDP has only 2 clock choice, no n/m/p setting */
+	if (HAS_eDP)
+		return true;
+
 	if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT))
 		return intel_find_pll_igdng_dp(limit, crtc, target,
 					       refclk, best_clock);
@@ -1052,6 +1075,67 @@ static void i915_disable_vga (struct drm_device *dev)
 	I915_WRITE(vga_reg, VGA_DISP_DISABLE);
 }
 
+static void igdng_disable_pll_edp (struct drm_crtc *crtc)
+{
+	struct drm_device *dev = crtc->dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	u32 dpa_ctl;
+
+	DRM_DEBUG("\n");
+	dpa_ctl = I915_READ(DP_A);
+	dpa_ctl &= ~DP_PLL_ENABLE;
+	I915_WRITE(DP_A, dpa_ctl);
+}
+
+static void igdng_enable_pll_edp (struct drm_crtc *crtc)
+{
+	struct drm_device *dev = crtc->dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	u32 dpa_ctl;
+
+	dpa_ctl = I915_READ(DP_A);
+	dpa_ctl |= DP_PLL_ENABLE;
+	I915_WRITE(DP_A, dpa_ctl);
+	udelay(200);
+}
+
+
+static void igdng_set_pll_edp (struct drm_crtc *crtc, int clock)
+{
+	struct drm_device *dev = crtc->dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	u32 dpa_ctl;
+
+	DRM_DEBUG("eDP PLL enable for clock %d\n", clock);
+	dpa_ctl = I915_READ(DP_A);
+	dpa_ctl &= ~DP_PLL_FREQ_MASK;
+
+	if (clock < 200000) {
+		u32 temp;
+		dpa_ctl |= DP_PLL_FREQ_160MHZ;
+		/* workaround for 160Mhz:
+		   1) program 0x4600c bits 15:0 = 0x8124
+		   2) program 0x46010 bit 0 = 1
+		   3) program 0x46034 bit 24 = 1
+		   4) program 0x64000 bit 14 = 1
+		   */
+		temp = I915_READ(0x4600c);
+		temp &= 0xffff0000;
+		I915_WRITE(0x4600c, temp | 0x8124);
+
+		temp = I915_READ(0x46010);
+		I915_WRITE(0x46010, temp | 1);
+
+		temp = I915_READ(0x46034);
+		I915_WRITE(0x46034, temp | (1 << 24));
+	} else {
+		dpa_ctl |= DP_PLL_FREQ_270MHZ;
+	}
+	I915_WRITE(DP_A, dpa_ctl);
+
+	udelay(500);
+}
+
 static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 {
 	struct drm_device *dev = crtc->dev;
@@ -1093,27 +1177,32 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 	case DRM_MODE_DPMS_STANDBY:
 	case DRM_MODE_DPMS_SUSPEND:
 		DRM_DEBUG("crtc %d dpms on\n", pipe);
-		/* enable PCH DPLL */
-		temp = I915_READ(pch_dpll_reg);
-		if ((temp & DPLL_VCO_ENABLE) == 0) {
-			I915_WRITE(pch_dpll_reg, temp | DPLL_VCO_ENABLE);
-			I915_READ(pch_dpll_reg);
-		}
-
-		/* enable PCH FDI RX PLL, wait warmup plus DMI latency */
-		temp = I915_READ(fdi_rx_reg);
-		I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE |
-				FDI_SEL_PCDCLK |
-				FDI_DP_PORT_WIDTH_X4); /* default 4 lanes */
-		I915_READ(fdi_rx_reg);
-		udelay(200);
+		if (HAS_eDP) {
+			/* enable eDP PLL */
+			igdng_enable_pll_edp(crtc);
+		} else {
+			/* enable PCH DPLL */
+			temp = I915_READ(pch_dpll_reg);
+			if ((temp & DPLL_VCO_ENABLE) == 0) {
+				I915_WRITE(pch_dpll_reg, temp | DPLL_VCO_ENABLE);
+				I915_READ(pch_dpll_reg);
+			}
 
-		/* Enable CPU FDI TX PLL, always on for IGDNG */
-		temp = I915_READ(fdi_tx_reg);
-		if ((temp & FDI_TX_PLL_ENABLE) == 0) {
-			I915_WRITE(fdi_tx_reg, temp | FDI_TX_PLL_ENABLE);
-			I915_READ(fdi_tx_reg);
-			udelay(100);
+			/* enable PCH FDI RX PLL, wait warmup plus DMI latency */
+			temp = I915_READ(fdi_rx_reg);
+			I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE |
+					FDI_SEL_PCDCLK |
+					FDI_DP_PORT_WIDTH_X4); /* default 4 lanes */
+			I915_READ(fdi_rx_reg);
+			udelay(200);
+
+			/* Enable CPU FDI TX PLL, always on for IGDNG */
+			temp = I915_READ(fdi_tx_reg);
+			if ((temp & FDI_TX_PLL_ENABLE) == 0) {
+				I915_WRITE(fdi_tx_reg, temp | FDI_TX_PLL_ENABLE);
+				I915_READ(fdi_tx_reg);
+				udelay(100);
+			}
 		}
 
 		/* Enable CPU pipe */
@@ -1132,122 +1221,126 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 			I915_WRITE(dspbase_reg, I915_READ(dspbase_reg));
 		}
 
-		/* enable CPU FDI TX and PCH FDI RX */
-		temp = I915_READ(fdi_tx_reg);
-		temp |= FDI_TX_ENABLE;
-		temp |= FDI_DP_PORT_WIDTH_X4; /* default */
-		temp &= ~FDI_LINK_TRAIN_NONE;
-		temp |= FDI_LINK_TRAIN_PATTERN_1;
-		I915_WRITE(fdi_tx_reg, temp);
-		I915_READ(fdi_tx_reg);
+		if (!HAS_eDP) {
+			/* enable CPU FDI TX and PCH FDI RX */
+			temp = I915_READ(fdi_tx_reg);
+			temp |= FDI_TX_ENABLE;
+			temp |= FDI_DP_PORT_WIDTH_X4; /* default */
+			temp &= ~FDI_LINK_TRAIN_NONE;
+			temp |= FDI_LINK_TRAIN_PATTERN_1;
+			I915_WRITE(fdi_tx_reg, temp);
+			I915_READ(fdi_tx_reg);
 
-		temp = I915_READ(fdi_rx_reg);
-		temp &= ~FDI_LINK_TRAIN_NONE;
-		temp |= FDI_LINK_TRAIN_PATTERN_1;
-		I915_WRITE(fdi_rx_reg, temp | FDI_RX_ENABLE);
-		I915_READ(fdi_rx_reg);
+			temp = I915_READ(fdi_rx_reg);
+			temp &= ~FDI_LINK_TRAIN_NONE;
+			temp |= FDI_LINK_TRAIN_PATTERN_1;
+			I915_WRITE(fdi_rx_reg, temp | FDI_RX_ENABLE);
+			I915_READ(fdi_rx_reg);
 
-		udelay(150);
+			udelay(150);
 
-		/* Train FDI. */
-		/* umask FDI RX Interrupt symbol_lock and bit_lock bit
-		   for train result */
-		temp = I915_READ(fdi_rx_imr_reg);
-		temp &= ~FDI_RX_SYMBOL_LOCK;
-		temp &= ~FDI_RX_BIT_LOCK;
-		I915_WRITE(fdi_rx_imr_reg, temp);
-		I915_READ(fdi_rx_imr_reg);
-		udelay(150);
+			/* Train FDI. */
+			/* umask FDI RX Interrupt symbol_lock and bit_lock bit
+			   for train result */
+			temp = I915_READ(fdi_rx_imr_reg);
+			temp &= ~FDI_RX_SYMBOL_LOCK;
+			temp &= ~FDI_RX_BIT_LOCK;
+			I915_WRITE(fdi_rx_imr_reg, temp);
+			I915_READ(fdi_rx_imr_reg);
+			udelay(150);
 
-		temp = I915_READ(fdi_rx_iir_reg);
-		DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp);
+			temp = I915_READ(fdi_rx_iir_reg);
+			DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp);
 
-		if ((temp & FDI_RX_BIT_LOCK) == 0) {
-			for (j = 0; j < tries; j++) {
-				temp = I915_READ(fdi_rx_iir_reg);
-				DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp);
-				if (temp & FDI_RX_BIT_LOCK)
-					break;
-				udelay(200);
-			}
-			if (j != tries)
+			if ((temp & FDI_RX_BIT_LOCK) == 0) {
+				for (j = 0; j < tries; j++) {
+					temp = I915_READ(fdi_rx_iir_reg);
+					DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp);
+					if (temp & FDI_RX_BIT_LOCK)
+						break;
+					udelay(200);
+				}
+				if (j != tries)
+					I915_WRITE(fdi_rx_iir_reg,
+							temp | FDI_RX_BIT_LOCK);
+				else
+					DRM_DEBUG("train 1 fail\n");
+			} else {
 				I915_WRITE(fdi_rx_iir_reg,
 						temp | FDI_RX_BIT_LOCK);
-			else
-				DRM_DEBUG("train 1 fail\n");
-		} else {
-			I915_WRITE(fdi_rx_iir_reg,
-					temp | FDI_RX_BIT_LOCK);
-			DRM_DEBUG("train 1 ok 2!\n");
-		}
-		temp = I915_READ(fdi_tx_reg);
-		temp &= ~FDI_LINK_TRAIN_NONE;
-		temp |= FDI_LINK_TRAIN_PATTERN_2;
-		I915_WRITE(fdi_tx_reg, temp);
-
-		temp = I915_READ(fdi_rx_reg);
-		temp &= ~FDI_LINK_TRAIN_NONE;
-		temp |= FDI_LINK_TRAIN_PATTERN_2;
-		I915_WRITE(fdi_rx_reg, temp);
+				DRM_DEBUG("train 1 ok 2!\n");
+			}
+			temp = I915_READ(fdi_tx_reg);
+			temp &= ~FDI_LINK_TRAIN_NONE;
+			temp |= FDI_LINK_TRAIN_PATTERN_2;
+			I915_WRITE(fdi_tx_reg, temp);
+
+			temp = I915_READ(fdi_rx_reg);
+			temp &= ~FDI_LINK_TRAIN_NONE;
+			temp |= FDI_LINK_TRAIN_PATTERN_2;
+			I915_WRITE(fdi_rx_reg, temp);
 
-		udelay(150);
+			udelay(150);
 
-		temp = I915_READ(fdi_rx_iir_reg);
-		DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp);
+			temp = I915_READ(fdi_rx_iir_reg);
+			DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp);
 
-		if ((temp & FDI_RX_SYMBOL_LOCK) == 0) {
-			for (j = 0; j < tries; j++) {
-				temp = I915_READ(fdi_rx_iir_reg);
-				DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp);
-				if (temp & FDI_RX_SYMBOL_LOCK)
-					break;
-				udelay(200);
-			}
-			if (j != tries) {
+			if ((temp & FDI_RX_SYMBOL_LOCK) == 0) {
+				for (j = 0; j < tries; j++) {
+					temp = I915_READ(fdi_rx_iir_reg);
+					DRM_DEBUG("FDI_RX_IIR 0x%x\n", temp);
+					if (temp & FDI_RX_SYMBOL_LOCK)
+						break;
+					udelay(200);
+				}
+				if (j != tries) {
+					I915_WRITE(fdi_rx_iir_reg,
+							temp | FDI_RX_SYMBOL_LOCK);
+					DRM_DEBUG("train 2 ok 1!\n");
+				} else
+					DRM_DEBUG("train 2 fail\n");
+			} else {
 				I915_WRITE(fdi_rx_iir_reg,
 						temp | FDI_RX_SYMBOL_LOCK);
-				DRM_DEBUG("train 2 ok 1!\n");
-			} else
-				DRM_DEBUG("train 2 fail\n");
-		} else {
-			I915_WRITE(fdi_rx_iir_reg, temp | FDI_RX_SYMBOL_LOCK);
-			DRM_DEBUG("train 2 ok 2!\n");
-		}
-		DRM_DEBUG("train done\n");
+				DRM_DEBUG("train 2 ok 2!\n");
+			}
+			DRM_DEBUG("train done\n");
 
-		/* set transcoder timing */
-		I915_WRITE(trans_htot_reg, I915_READ(cpu_htot_reg));
-		I915_WRITE(trans_hblank_reg, I915_READ(cpu_hblank_reg));
-		I915_WRITE(trans_hsync_reg, I915_READ(cpu_hsync_reg));
+			/* set transcoder timing */
+			I915_WRITE(trans_htot_reg, I915_READ(cpu_htot_reg));
+			I915_WRITE(trans_hblank_reg, I915_READ(cpu_hblank_reg));
+			I915_WRITE(trans_hsync_reg, I915_READ(cpu_hsync_reg));
 
-		I915_WRITE(trans_vtot_reg, I915_READ(cpu_vtot_reg));
-		I915_WRITE(trans_vblank_reg, I915_READ(cpu_vblank_reg));
-		I915_WRITE(trans_vsync_reg, I915_READ(cpu_vsync_reg));
+			I915_WRITE(trans_vtot_reg, I915_READ(cpu_vtot_reg));
+			I915_WRITE(trans_vblank_reg, I915_READ(cpu_vblank_reg));
+			I915_WRITE(trans_vsync_reg, I915_READ(cpu_vsync_reg));
 
-		/* enable PCH transcoder */
-		temp = I915_READ(transconf_reg);
-		I915_WRITE(transconf_reg, temp | TRANS_ENABLE);
-		I915_READ(transconf_reg);
+			/* enable PCH transcoder */
+			temp = I915_READ(transconf_reg);
+			I915_WRITE(transconf_reg, temp | TRANS_ENABLE);
+			I915_READ(transconf_reg);
 
-		while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) == 0)
-			;
+			while ((I915_READ(transconf_reg) & TRANS_STATE_ENABLE) == 0)
+				;
 
-		/* enable normal */
+			/* enable normal */
 
-		temp = I915_READ(fdi_tx_reg);
-		temp &= ~FDI_LINK_TRAIN_NONE;
-		I915_WRITE(fdi_tx_reg, temp | FDI_LINK_TRAIN_NONE |
-				FDI_TX_ENHANCE_FRAME_ENABLE);
-		I915_READ(fdi_tx_reg);
+			temp = I915_READ(fdi_tx_reg);
+			temp &= ~FDI_LINK_TRAIN_NONE;
+			I915_WRITE(fdi_tx_reg, temp | FDI_LINK_TRAIN_NONE |
+					FDI_TX_ENHANCE_FRAME_ENABLE);
+			I915_READ(fdi_tx_reg);
 
-		temp = I915_READ(fdi_rx_reg);
-		temp &= ~FDI_LINK_TRAIN_NONE;
-		I915_WRITE(fdi_rx_reg, temp | FDI_LINK_TRAIN_NONE |
-				FDI_RX_ENHANCE_FRAME_ENABLE);
-		I915_READ(fdi_rx_reg);
+			temp = I915_READ(fdi_rx_reg);
+			temp &= ~FDI_LINK_TRAIN_NONE;
+			I915_WRITE(fdi_rx_reg, temp | FDI_LINK_TRAIN_NONE |
+					FDI_RX_ENHANCE_FRAME_ENABLE);
+			I915_READ(fdi_rx_reg);
 
-		/* wait one idle pattern time */
-		udelay(100);
+			/* wait one idle pattern time */
+			udelay(100);
+
+		}
 
 		intel_crtc_load_lut(crtc);
 
@@ -1286,6 +1379,10 @@ static void igdng_crtc_dpms(struct drm_crtc *crtc, int mode)
 		} else
 			DRM_DEBUG("crtc %d is disabled\n", pipe);
 
+		if (HAS_eDP) {
+			igdng_disable_pll_edp(crtc);
+		}
+
 		/* disable CPU FDI tx and PCH FDI rx */
 		temp = I915_READ(fdi_tx_reg);
 		I915_WRITE(fdi_tx_reg, temp & ~FDI_TX_ENABLE);
@@ -2152,6 +2249,7 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 	u32 dpll = 0, fp = 0, dspcntr, pipeconf;
 	bool ok, is_sdvo = false, is_dvo = false;
 	bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false;
+	bool is_edp = false;
 	struct drm_mode_config *mode_config = &dev->mode_config;
 	struct drm_connector *connector;
 	const intel_limit_t *limit;
@@ -2199,6 +2297,9 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 		case INTEL_OUTPUT_DISPLAYPORT:
 			is_dp = true;
 			break;
+		case INTEL_OUTPUT_EDP:
+			is_edp = true;
+			break;
 		}
 
 		num_outputs++;
@@ -2251,16 +2352,27 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 
 	/* FDI link */
 	if (IS_IGDNG(dev)) {
-		/* DP over FDI requires target mode clock
-		   instead of link clock */
-		if (is_dp)
+		int lane, link_bw;
+		/* eDP doesn't require FDI link, so just set DP M/N
+		   according to current link config */
+		if (is_edp) {
+			struct drm_connector *edp;
 			target_clock = mode->clock;
-		else
-			target_clock = adjusted_mode->clock;
-		igdng_compute_m_n(3, 4, /* lane num 4 */
-				target_clock,
-				270000, /* lane clock */
-				&m_n);
+			edp = intel_pipe_get_output(crtc);
+			intel_edp_link_config(to_intel_output(edp),
+					&lane, &link_bw);
+		} else {
+			/* DP over FDI requires target mode clock
+			   instead of link clock */
+			if (is_dp)
+				target_clock = mode->clock;
+			else
+				target_clock = adjusted_mode->clock;
+			lane = 4;
+			link_bw = 270000;
+		}
+		igdng_compute_m_n(3, lane, target_clock,
+				  link_bw, &m_n);
 	}
 
 	if (IS_IGD(dev))
@@ -2382,29 +2494,15 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 		dpll_reg = pch_dpll_reg;
 	}
 
-	if (dpll & DPLL_VCO_ENABLE) {
+	if (is_edp) {
+		igdng_disable_pll_edp(crtc);
+	} else if ((dpll & DPLL_VCO_ENABLE)) {
 		I915_WRITE(fp_reg, fp);
 		I915_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE);
 		I915_READ(dpll_reg);
 		udelay(150);
 	}
 
-	if (IS_IGDNG(dev)) {
-		/* enable PCH clock reference source */
-		/* XXX need to change the setting for other outputs */
-		u32 temp;
-		temp = I915_READ(PCH_DREF_CONTROL);
-		temp &= ~DREF_NONSPREAD_SOURCE_MASK;
-		temp |= DREF_NONSPREAD_CK505_ENABLE;
-		temp &= ~DREF_SSC_SOURCE_MASK;
-		temp |= DREF_SSC_SOURCE_ENABLE;
-		temp &= ~DREF_SSC1_ENABLE;
-		/* if no eDP, disable source output to CPU */
-		temp &= ~DREF_CPU_SOURCE_OUTPUT_MASK;
-		temp |= DREF_CPU_SOURCE_OUTPUT_DISABLE;
-		I915_WRITE(PCH_DREF_CONTROL, temp);
-	}
-
 	/* The LVDS pin pair needs to be on before the DPLLs are enabled.
 	 * This is an exception to the general rule that mode_set doesn't turn
 	 * things on.
@@ -2436,23 +2534,25 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 	if (is_dp)
 		intel_dp_set_m_n(crtc, mode, adjusted_mode);
 
-	I915_WRITE(fp_reg, fp);
-	I915_WRITE(dpll_reg, dpll);
-	I915_READ(dpll_reg);
-	/* Wait for the clocks to stabilize. */
-	udelay(150);
-
-	if (IS_I965G(dev) && !IS_IGDNG(dev)) {
-		sdvo_pixel_multiply = adjusted_mode->clock / mode->clock;
-		I915_WRITE(dpll_md_reg, (0 << DPLL_MD_UDI_DIVIDER_SHIFT) |
-			   ((sdvo_pixel_multiply - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT));
-	} else {
-		/* write it again -- the BIOS does, after all */
+	if (!is_edp) {
+		I915_WRITE(fp_reg, fp);
 		I915_WRITE(dpll_reg, dpll);
+		I915_READ(dpll_reg);
+		/* Wait for the clocks to stabilize. */
+		udelay(150);
+
+		if (IS_I965G(dev) && !IS_IGDNG(dev)) {
+			sdvo_pixel_multiply = adjusted_mode->clock / mode->clock;
+			I915_WRITE(dpll_md_reg, (0 << DPLL_MD_UDI_DIVIDER_SHIFT) |
+					((sdvo_pixel_multiply - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT));
+		} else {
+			/* write it again -- the BIOS does, after all */
+			I915_WRITE(dpll_reg, dpll);
+		}
+		I915_READ(dpll_reg);
+		/* Wait for the clocks to stabilize. */
+		udelay(150);
 	}
-	I915_READ(dpll_reg);
-	/* Wait for the clocks to stabilize. */
-	udelay(150);
 
 	I915_WRITE(htot_reg, (adjusted_mode->crtc_hdisplay - 1) |
 		   ((adjusted_mode->crtc_htotal - 1) << 16));
@@ -2482,10 +2582,14 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 		I915_WRITE(link_m1_reg, m_n.link_m);
 		I915_WRITE(link_n1_reg, m_n.link_n);
 
-		 /* enable FDI RX PLL too */
-		temp = I915_READ(fdi_rx_reg);
-		I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE);
-		udelay(200);
+		if (is_edp) {
+			igdng_set_pll_edp(crtc, adjusted_mode->clock);
+		} else {
+			/* enable FDI RX PLL too */
+			temp = I915_READ(fdi_rx_reg);
+			I915_WRITE(fdi_rx_reg, temp | FDI_RX_PLL_ENABLE);
+			udelay(200);
+		}
 	}
 
 	I915_WRITE(pipeconf_reg, pipeconf);
@@ -3083,6 +3187,9 @@ static void intel_setup_outputs(struct drm_device *dev)
 	if (IS_IGDNG(dev)) {
 		int found;
 
+		if (IS_MOBILE(dev) && (I915_READ(DP_A) & DP_DETECTED))
+			intel_dp_init(dev, DP_A);
+
 		if (I915_READ(HDMIB) & PORT_DETECTED) {
 			/* check SDVOB */
 			/* found = intel_sdvo_init(dev, HDMIB); */
@@ -3179,6 +3286,10 @@ static void intel_setup_outputs(struct drm_device *dev)
 				     (1 << 1));
 			clone_mask = (1 << INTEL_OUTPUT_DISPLAYPORT);
 			break;
+		case INTEL_OUTPUT_EDP:
+			crtc_mask = (1 << 1);
+			clone_mask = (1 << INTEL_OUTPUT_EDP);
+			break;
 		}
 		encoder->possible_crtcs = crtc_mask;
 		encoder->possible_clones = intel_connector_clones(dev, clone_mask);
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 0715911cbd8..a6ff15ac548 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -40,6 +40,8 @@
 
 #define DP_LINK_CONFIGURATION_SIZE	9
 
+#define IS_eDP(i) ((i)->type == INTEL_OUTPUT_EDP)
+
 struct intel_dp_priv {
 	uint32_t output_reg;
 	uint32_t DP;
@@ -63,6 +65,19 @@ intel_dp_link_train(struct intel_output *intel_output, uint32_t DP,
 static void
 intel_dp_link_down(struct intel_output *intel_output, uint32_t DP);
 
+void
+intel_edp_link_config (struct intel_output *intel_output,
+		int *lane_num, int *link_bw)
+{
+	struct intel_dp_priv   *dp_priv = intel_output->dev_priv;
+
+	*lane_num = dp_priv->lane_count;
+	if (dp_priv->link_bw == DP_LINK_BW_1_62)
+		*link_bw = 162000;
+	else if (dp_priv->link_bw == DP_LINK_BW_2_7)
+		*link_bw = 270000;
+}
+
 static int
 intel_dp_max_lane_count(struct intel_output *intel_output)
 {
@@ -206,9 +221,10 @@ intel_dp_aux_ch(struct intel_output *intel_output,
 	 * and would like to run at 2MHz. So, take the
 	 * hrawclk value and divide by 2 and use that
 	 */
-	/* IGDNG: input clock fixed at 125Mhz, so aux_bit_clk always 62 */
-	if (IS_IGDNG(dev))
-		aux_clock_divider = 62;
+	if (IS_eDP(intel_output))
+		aux_clock_divider = 225; /* eDP input clock at 450Mhz */
+	else if (IS_IGDNG(dev))
+		aux_clock_divider = 62; /* IGDNG: input clock fixed at 125Mhz */
 	else
 		aux_clock_divider = intel_hrawclk(dev) / 2;
 
@@ -579,8 +595,38 @@ intel_dp_mode_set(struct drm_encoder *encoder, struct drm_display_mode *mode,
 
 	if (intel_crtc->pipe == 1)
 		dp_priv->DP |= DP_PIPEB_SELECT;
+
+	if (IS_eDP(intel_output)) {
+		/* don't miss out required setting for eDP */
+		dp_priv->DP |= DP_PLL_ENABLE;
+		if (adjusted_mode->clock < 200000)
+			dp_priv->DP |= DP_PLL_FREQ_160MHZ;
+		else
+			dp_priv->DP |= DP_PLL_FREQ_270MHZ;
+	}
 }
 
+static void igdng_edp_backlight_on (struct drm_device *dev)
+{
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	u32 pp;
+
+	DRM_DEBUG("\n");
+	pp = I915_READ(PCH_PP_CONTROL);
+	pp |= EDP_BLC_ENABLE;
+	I915_WRITE(PCH_PP_CONTROL, pp);
+}
+
+static void igdng_edp_backlight_off (struct drm_device *dev)
+{
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	u32 pp;
+
+	DRM_DEBUG("\n");
+	pp = I915_READ(PCH_PP_CONTROL);
+	pp &= ~EDP_BLC_ENABLE;
+	I915_WRITE(PCH_PP_CONTROL, pp);
+}
 
 static void
 intel_dp_dpms(struct drm_encoder *encoder, int mode)
@@ -592,11 +638,17 @@ intel_dp_dpms(struct drm_encoder *encoder, int mode)
 	uint32_t dp_reg = I915_READ(dp_priv->output_reg);
 
 	if (mode != DRM_MODE_DPMS_ON) {
-		if (dp_reg & DP_PORT_EN)
+		if (dp_reg & DP_PORT_EN) {
 			intel_dp_link_down(intel_output, dp_priv->DP);
+			if (IS_eDP(intel_output))
+				igdng_edp_backlight_off(dev);
+		}
 	} else {
-		if (!(dp_reg & DP_PORT_EN))
+		if (!(dp_reg & DP_PORT_EN)) {
 			intel_dp_link_train(intel_output, dp_priv->DP, dp_priv->link_configuration);
+			if (IS_eDP(intel_output))
+				igdng_edp_backlight_on(dev);
+		}
 	}
 	dp_priv->dpms_mode = mode;
 }
@@ -958,12 +1010,23 @@ intel_dp_link_down(struct intel_output *intel_output, uint32_t DP)
 	struct drm_i915_private *dev_priv = dev->dev_private;
 	struct intel_dp_priv *dp_priv = intel_output->dev_priv;
 
+	DRM_DEBUG("\n");
+
+	if (IS_eDP(intel_output)) {
+		DP &= ~DP_PLL_ENABLE;
+		I915_WRITE(dp_priv->output_reg, DP);
+		POSTING_READ(dp_priv->output_reg);
+		udelay(100);
+	}
+
 	DP &= ~DP_LINK_TRAIN_MASK;
 	I915_WRITE(dp_priv->output_reg, DP | DP_LINK_TRAIN_PAT_IDLE);
 	POSTING_READ(dp_priv->output_reg);
 
 	udelay(17000);
 
+	if (IS_eDP(intel_output))
+		DP |= DP_LINK_TRAIN_OFF;
 	I915_WRITE(dp_priv->output_reg, DP & ~DP_PORT_EN);
 	POSTING_READ(dp_priv->output_reg);
 }
@@ -1089,11 +1152,27 @@ intel_dp_detect(struct drm_connector *connector)
 static int intel_dp_get_modes(struct drm_connector *connector)
 {
 	struct intel_output *intel_output = to_intel_output(connector);
+	struct drm_device *dev = intel_output->base.dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	int ret;
 
 	/* We should parse the EDID data and find out if it has an audio sink
 	 */
 
-	return intel_ddc_get_modes(intel_output);
+	ret = intel_ddc_get_modes(intel_output);
+	if (ret)
+		return ret;
+
+	/* if eDP has no EDID, try to use fixed panel mode from VBT */
+	if (IS_eDP(intel_output)) {
+		if (dev_priv->panel_fixed_mode != NULL) {
+			struct drm_display_mode *mode;
+			mode = drm_mode_duplicate(dev, dev_priv->panel_fixed_mode);
+			drm_mode_probed_add(connector, mode);
+			return 1;
+		}
+	}
+	return 0;
 }
 
 static void
@@ -1170,7 +1249,10 @@ intel_dp_init(struct drm_device *dev, int output_reg)
 			   DRM_MODE_CONNECTOR_DisplayPort);
 	drm_connector_helper_add(connector, &intel_dp_connector_helper_funcs);
 
-	intel_output->type = INTEL_OUTPUT_DISPLAYPORT;
+	if (output_reg == DP_A)
+		intel_output->type = INTEL_OUTPUT_EDP;
+	else
+		intel_output->type = INTEL_OUTPUT_DISPLAYPORT;
 
 	connector->interlace_allowed = true;
 	connector->doublescan_allowed = 0;
@@ -1191,6 +1273,9 @@ intel_dp_init(struct drm_device *dev, int output_reg)
 
 	/* Set up the DDC bus. */
 	switch (output_reg) {
+		case DP_A:
+			name = "DPDDC-A";
+			break;
 		case DP_B:
 		case PCH_DP_B:
 			name = "DPDDC-B";
@@ -1206,9 +1291,22 @@ intel_dp_init(struct drm_device *dev, int output_reg)
 	}
 
 	intel_dp_i2c_init(intel_output, name);
+
 	intel_output->ddc_bus = &dp_priv->adapter;
 	intel_output->hot_plug = intel_dp_hot_plug;
 
+	if (output_reg == DP_A) {
+		/* initialize panel mode from VBT if available for eDP */
+		if (dev_priv->lfp_lvds_vbt_mode) {
+			dev_priv->panel_fixed_mode =
+				drm_mode_duplicate(dev, dev_priv->lfp_lvds_vbt_mode);
+			if (dev_priv->panel_fixed_mode) {
+				dev_priv->panel_fixed_mode->type |=
+					DRM_MODE_TYPE_PREFERRED;
+			}
+		}
+	}
+
 	/* For G4X desktop chip, PEG_BAND_GAP_DATA 3:0 must first be written
 	 * 0xd.  Failure to do so will result in spurious interrupts being
 	 * generated on the port when a cable is not attached.
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index 004541c935a..d6f92ea1b55 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -55,6 +55,7 @@
 #define INTEL_OUTPUT_TVOUT 5
 #define INTEL_OUTPUT_HDMI 6
 #define INTEL_OUTPUT_DISPLAYPORT 7
+#define INTEL_OUTPUT_EDP 8
 
 #define INTEL_DVO_CHIP_NONE 0
 #define INTEL_DVO_CHIP_LVDS 1
@@ -121,6 +122,8 @@ extern void intel_dp_init(struct drm_device *dev, int dp_reg);
 void
 intel_dp_set_m_n(struct drm_crtc *crtc, struct drm_display_mode *mode,
 		 struct drm_display_mode *adjusted_mode);
+extern void intel_edp_link_config (struct intel_output *, int *, int *);
+
 
 extern void intel_crtc_load_lut(struct drm_crtc *crtc);
 extern void intel_encoder_prepare (struct drm_encoder *encoder);
diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c
index 43c7d9aa59c..3f445a80c55 100644
--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -892,6 +892,10 @@ void intel_lvds_init(struct drm_device *dev)
 	if (IS_IGDNG(dev)) {
 		if ((I915_READ(PCH_LVDS) & LVDS_DETECTED) == 0)
 			return;
+		if (dev_priv->edp_support) {
+			DRM_DEBUG("disable LVDS for eDP support\n");
+			return;
+		}
 		gpio = PCH_GPIOC;
 	}
 
-- 
GitLab


From 67941da28d59cca6817d35823fcb1e3e4eed030e Mon Sep 17 00:00:00 2001
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Fri, 24 Jul 2009 01:00:33 +0800
Subject: [PATCH 0235/1153] drm/i915: fix VGA detect on IGDNG

Check FORCE_DETECT bit to be clear for the finish
of hotplug detect process. Also check possible mono
monitor which should also be marked as connected.

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_crt.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_crt.c b/drivers/gpu/drm/i915/intel_crt.c
index d6a1a6e5539..4cf8e2e88a4 100644
--- a/drivers/gpu/drm/i915/intel_crt.c
+++ b/drivers/gpu/drm/i915/intel_crt.c
@@ -156,6 +156,9 @@ static bool intel_igdng_crt_detect_hotplug(struct drm_connector *connector)
 
 	temp = adpa = I915_READ(PCH_ADPA);
 
+	adpa &= ~ADPA_DAC_ENABLE;
+	I915_WRITE(PCH_ADPA, adpa);
+
 	adpa &= ~ADPA_CRT_HOTPLUG_MASK;
 
 	adpa |= (ADPA_CRT_HOTPLUG_PERIOD_128 |
@@ -169,13 +172,14 @@ static bool intel_igdng_crt_detect_hotplug(struct drm_connector *connector)
 	DRM_DEBUG("pch crt adpa 0x%x", adpa);
 	I915_WRITE(PCH_ADPA, adpa);
 
-	/* This might not be needed as not specified in spec...*/
-	udelay(1000);
+	while ((I915_READ(PCH_ADPA) & ADPA_CRT_HOTPLUG_FORCE_TRIGGER) != 0)
+		;
 
 	/* Check the status to see if both blue and green are on now */
 	adpa = I915_READ(PCH_ADPA);
-	if ((adpa & ADPA_CRT_HOTPLUG_MONITOR_MASK) ==
-			ADPA_CRT_HOTPLUG_MONITOR_COLOR)
+	adpa &= ADPA_CRT_HOTPLUG_MONITOR_MASK;
+	if ((adpa == ADPA_CRT_HOTPLUG_MONITOR_COLOR) ||
+		(adpa == ADPA_CRT_HOTPLUG_MONITOR_MONO))
 		ret = true;
 	else
 		ret = false;
-- 
GitLab


From f360132626b11d0dc60814033873ca0e3111677c Mon Sep 17 00:00:00 2001
From: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed, 22 Jul 2009 12:54:59 -0700
Subject: [PATCH 0236/1153] drm/i915: fix 845G FIFO size & burst length

I had one report of flicker due to FIFO underruns on 845G.  Scott was
kind enough to test a few patches and report success with this one.
Looks like 845G measures FIFO size slightly differently than other
chips, and we were also clobbering the FIFO burst length.  Fixing both
of those issues gives him a healthy machine again.

Note that we still only adjust plane A's watermark in the 830/845
case.  If someone is willing to test we could support a bigger variety
of dual-head 830/845 configurations with a bit more code.

Fixes fdo bug #19304 (again).

Reported-by: Scott Hansen <scottandchrystie@comcast.net>
Tested-by: Scott Hansen <scottandchrystie@comcast.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_display.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index a9f1307d32d..1da7b0b9ed3 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -2026,6 +2026,9 @@ static int intel_get_fifo_size(struct drm_device *dev, int plane)
 			size = ((dsparb >> DSPARB_BEND_SHIFT) & 0x1ff) -
 				(dsparb & 0x1ff);
 		size >>= 1; /* Convert to cachelines */
+	} else if (IS_845G(dev)) {
+		size = dsparb & 0x7f;
+		size >>= 2; /* Convert to cachelines */
 	} else {
 		size = dsparb & 0x7f;
 		size >>= 1; /* Convert to cachelines */
@@ -2125,14 +2128,16 @@ static void i830_update_wm(struct drm_device *dev, int planea_clock,
 			   int pixel_size)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
-	uint32_t fwater_lo = I915_READ(FW_BLC) & MM_FIFO_WATERMARK;
+	uint32_t fwater_lo = I915_READ(FW_BLC) & ~0xfff;
 	int planea_wm;
 
 	i830_wm_info.fifo_size = intel_get_fifo_size(dev, 0);
 
 	planea_wm = intel_calculate_wm(planea_clock, &i830_wm_info,
 				       pixel_size, latency_ns);
-	fwater_lo = fwater_lo | planea_wm;
+	fwater_lo |= (3<<8) | planea_wm;
+
+	DRM_DEBUG("Setting FIFO watermarks - A: %d\n", planea_wm);
 
 	I915_WRITE(FW_BLC, fwater_lo);
 }
-- 
GitLab


From bcae2ca81c4a085e3e0e8941b7c64f9aeb6fc05c Mon Sep 17 00:00:00 2001
From: "ling.ma@intel.com" <ling.ma@intel.com>
Date: Mon, 20 Jul 2009 13:20:23 +0800
Subject: [PATCH 0237/1153] drm/i915: Set preferred mode for integrated TV
 according to TV format

In order to get best possible quality image we chose 640x480 for
NTSC, PAL and 480p, 1280x720 for 720p, 1920x1080 for 1080i/p
TV format respectively.

Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_tv.c | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/drivers/gpu/drm/i915/intel_tv.c b/drivers/gpu/drm/i915/intel_tv.c
index a43c98e3f07..da4ab4dc163 100644
--- a/drivers/gpu/drm/i915/intel_tv.c
+++ b/drivers/gpu/drm/i915/intel_tv.c
@@ -1490,6 +1490,27 @@ static struct input_res {
 	{"1920x1080", 1920, 1080},
 };
 
+/*
+ * Chose preferred mode  according to line number of TV format
+ */
+static void
+intel_tv_chose_preferred_modes(struct drm_connector *connector,
+			       struct drm_display_mode *mode_ptr)
+{
+	struct intel_output *intel_output = to_intel_output(connector);
+	const struct tv_mode *tv_mode = intel_tv_mode_find(intel_output);
+
+	if (tv_mode->nbr_end < 480 && mode_ptr->vdisplay == 480)
+		mode_ptr->type |= DRM_MODE_TYPE_PREFERRED;
+	else if (tv_mode->nbr_end > 480) {
+		if (tv_mode->progressive == true && tv_mode->nbr_end < 720) {
+			if (mode_ptr->vdisplay == 720)
+				mode_ptr->type |= DRM_MODE_TYPE_PREFERRED;
+		} else if (mode_ptr->vdisplay == 1080)
+				mode_ptr->type |= DRM_MODE_TYPE_PREFERRED;
+	}
+}
+
 /**
  * Stub get_modes function.
  *
@@ -1544,6 +1565,7 @@ intel_tv_get_modes(struct drm_connector *connector)
 		mode_ptr->clock = (int) tmp;
 
 		mode_ptr->type = DRM_MODE_TYPE_DRIVER;
+		intel_tv_chose_preferred_modes(connector, mode_ptr);
 		drm_mode_probed_add(connector, mode_ptr);
 		count++;
 	}
-- 
GitLab


From fb7a46f3cc7d7dcf7c5edb3a38c84e3f730d7adb Mon Sep 17 00:00:00 2001
From: "ling.ma@intel.com" <ling.ma@intel.com>
Date: Thu, 23 Jul 2009 17:11:34 +0800
Subject: [PATCH 0238/1153] drm/i915: Choose real sdvo output according to
 result from detection

Baed on Eric's idea in order to handle multiple sdvo encoders
we implement another approach to dynamically chose real one
encoder after detection, which is contrasted with patch -
drm/i915:Construct all possible sdvo outputs for sdvo encoder.

Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_sdvo.c | 231 ++++++++++++++++++++----------
 1 file changed, 153 insertions(+), 78 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c
index 4f0c30948bc..b68746f0380 100644
--- a/drivers/gpu/drm/i915/intel_sdvo.c
+++ b/drivers/gpu/drm/i915/intel_sdvo.c
@@ -55,6 +55,12 @@ struct intel_sdvo_priv {
 	/* Pixel clock limitations reported by the SDVO device, in kHz */
 	int pixel_clock_min, pixel_clock_max;
 
+	/*
+	* For multiple function SDVO device,
+	* this is for current attached outputs.
+	*/
+	uint16_t attached_output;
+
 	/**
 	 * This is set if we're going to treat the device as TV-out.
 	 *
@@ -114,6 +120,9 @@ struct intel_sdvo_priv {
 	u32 save_SDVOX;
 };
 
+static bool
+intel_sdvo_output_setup(struct intel_output *intel_output, uint16_t flags);
+
 /**
  * Writes the SDVOB or SDVOC with the given value, but always writes both
  * SDVOB and SDVOC to work around apparent hardware issues (according to
@@ -1435,6 +1444,39 @@ void intel_sdvo_set_hotplug(struct drm_connector *connector, int on)
 	intel_sdvo_read_response(intel_output, &response, 2);
 }
 
+static bool
+intel_sdvo_multifunc_encoder(struct intel_output *intel_output)
+{
+	struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv;
+	int caps = 0;
+
+	if (sdvo_priv->caps.output_flags &
+		(SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1))
+		caps++;
+	if (sdvo_priv->caps.output_flags &
+		(SDVO_OUTPUT_RGB0 | SDVO_OUTPUT_RGB1))
+		caps++;
+	if (sdvo_priv->caps.output_flags &
+		(SDVO_OUTPUT_SVID0 | SDVO_OUTPUT_SVID0))
+		caps++;
+	if (sdvo_priv->caps.output_flags &
+		(SDVO_OUTPUT_CVBS0 | SDVO_OUTPUT_CVBS1))
+		caps++;
+	if (sdvo_priv->caps.output_flags &
+		(SDVO_OUTPUT_YPRPB0 | SDVO_OUTPUT_YPRPB1))
+		caps++;
+
+	if (sdvo_priv->caps.output_flags &
+		(SDVO_OUTPUT_SCART0 | SDVO_OUTPUT_SCART1))
+		caps++;
+
+	if (sdvo_priv->caps.output_flags &
+		(SDVO_OUTPUT_LVDS0 | SDVO_OUTPUT_LVDS1))
+		caps++;
+
+	return (caps > 1);
+}
+
 static void
 intel_sdvo_hdmi_sink_detect(struct drm_connector *connector)
 {
@@ -1453,23 +1495,31 @@ intel_sdvo_hdmi_sink_detect(struct drm_connector *connector)
 
 static enum drm_connector_status intel_sdvo_detect(struct drm_connector *connector)
 {
-	u8 response[2];
+	uint16_t response;
 	u8 status;
 	struct intel_output *intel_output = to_intel_output(connector);
+	struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv;
 
 	intel_sdvo_write_cmd(intel_output, SDVO_CMD_GET_ATTACHED_DISPLAYS, NULL, 0);
 	status = intel_sdvo_read_response(intel_output, &response, 2);
 
-	DRM_DEBUG("SDVO response %d %d\n", response[0], response[1]);
+	DRM_DEBUG("SDVO response %d %d\n", response & 0xff, response >> 8);
 
 	if (status != SDVO_CMD_STATUS_SUCCESS)
 		return connector_status_unknown;
 
-	if ((response[0] != 0) || (response[1] != 0)) {
-		intel_sdvo_hdmi_sink_detect(connector);
-		return connector_status_connected;
-	} else
+	if (response == 0)
 		return connector_status_disconnected;
+
+	if (intel_sdvo_multifunc_encoder(intel_output) &&
+		sdvo_priv->attached_output != response) {
+		if (sdvo_priv->controlled_output != response &&
+			intel_sdvo_output_setup(intel_output, response) != true)
+			return connector_status_unknown;
+		sdvo_priv->attached_output = response;
+	}
+	intel_sdvo_hdmi_sink_detect(connector);
+	return connector_status_connected;
 }
 
 static void intel_sdvo_get_ddc_modes(struct drm_connector *connector)
@@ -1866,16 +1916,101 @@ intel_sdvo_get_slave_addr(struct drm_device *dev, int output_device)
 		return 0x72;
 }
 
+static bool
+intel_sdvo_output_setup(struct intel_output *intel_output, uint16_t flags)
+{
+	struct drm_connector *connector = &intel_output->base;
+	struct drm_encoder *encoder = &intel_output->enc;
+	struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv;
+	bool ret = true, registered = false;
+
+	sdvo_priv->is_tv = false;
+	intel_output->needs_tv_clock = false;
+	sdvo_priv->is_lvds = false;
+
+	if (device_is_registered(&connector->kdev)) {
+		drm_sysfs_connector_remove(connector);
+		registered = true;
+	}
+
+	if (flags &
+	    (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) {
+		if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_TMDS0)
+			sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS0;
+		else
+			sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS1;
+
+		encoder->encoder_type = DRM_MODE_ENCODER_TMDS;
+		connector->connector_type = DRM_MODE_CONNECTOR_DVID;
+
+		if (intel_sdvo_get_supp_encode(intel_output,
+					       &sdvo_priv->encode) &&
+		    intel_sdvo_get_digital_encoding_mode(intel_output) &&
+		    sdvo_priv->is_hdmi) {
+			/* enable hdmi encoding mode if supported */
+			intel_sdvo_set_encode(intel_output, SDVO_ENCODE_HDMI);
+			intel_sdvo_set_colorimetry(intel_output,
+						   SDVO_COLORIMETRY_RGB256);
+			connector->connector_type = DRM_MODE_CONNECTOR_HDMIA;
+		}
+	} else if (flags & SDVO_OUTPUT_SVID0) {
+
+		sdvo_priv->controlled_output = SDVO_OUTPUT_SVID0;
+		encoder->encoder_type = DRM_MODE_ENCODER_TVDAC;
+		connector->connector_type = DRM_MODE_CONNECTOR_SVIDEO;
+		sdvo_priv->is_tv = true;
+		intel_output->needs_tv_clock = true;
+	} else if (flags & SDVO_OUTPUT_RGB0) {
+
+		sdvo_priv->controlled_output = SDVO_OUTPUT_RGB0;
+		encoder->encoder_type = DRM_MODE_ENCODER_DAC;
+		connector->connector_type = DRM_MODE_CONNECTOR_VGA;
+	} else if (flags & SDVO_OUTPUT_RGB1) {
+
+		sdvo_priv->controlled_output = SDVO_OUTPUT_RGB1;
+		encoder->encoder_type = DRM_MODE_ENCODER_DAC;
+		connector->connector_type = DRM_MODE_CONNECTOR_VGA;
+	} else if (flags & SDVO_OUTPUT_LVDS0) {
+
+		sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS0;
+		encoder->encoder_type = DRM_MODE_ENCODER_LVDS;
+		connector->connector_type = DRM_MODE_CONNECTOR_LVDS;
+		sdvo_priv->is_lvds = true;
+	} else if (flags & SDVO_OUTPUT_LVDS1) {
+
+		sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS1;
+		encoder->encoder_type = DRM_MODE_ENCODER_LVDS;
+		connector->connector_type = DRM_MODE_CONNECTOR_LVDS;
+		sdvo_priv->is_lvds = true;
+	} else {
+
+		unsigned char bytes[2];
+
+		sdvo_priv->controlled_output = 0;
+		memcpy(bytes, &sdvo_priv->caps.output_flags, 2);
+		DRM_DEBUG_KMS(I915_SDVO,
+				"%s: Unknown SDVO output type (0x%02x%02x)\n",
+				  SDVO_NAME(sdvo_priv),
+				  bytes[0], bytes[1]);
+		ret = false;
+	}
+
+	if (ret && registered)
+		ret = drm_sysfs_connector_add(connector) == 0 ? true : false;
+
+
+	return ret;
+
+}
+
 bool intel_sdvo_init(struct drm_device *dev, int output_device)
 {
 	struct drm_connector *connector;
 	struct intel_output *intel_output;
 	struct intel_sdvo_priv *sdvo_priv;
 
-	int connector_type;
 	u8 ch[0x40];
 	int i;
-	int encoder_type;
 
 	intel_output = kcalloc(sizeof(struct intel_output)+sizeof(struct intel_sdvo_priv), 1, GFP_KERNEL);
 	if (!intel_output) {
@@ -1925,88 +2060,28 @@ bool intel_sdvo_init(struct drm_device *dev, int output_device)
 	intel_output->ddc_bus->algo = &intel_sdvo_i2c_bit_algo;
 
 	/* In defaut case sdvo lvds is false */
-	sdvo_priv->is_lvds = false;
 	intel_sdvo_get_capabilities(intel_output, &sdvo_priv->caps);
 
-	if (sdvo_priv->caps.output_flags &
-	    (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) {
-		if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_TMDS0)
-			sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS0;
-		else
-			sdvo_priv->controlled_output = SDVO_OUTPUT_TMDS1;
-
-		encoder_type = DRM_MODE_ENCODER_TMDS;
-		connector_type = DRM_MODE_CONNECTOR_DVID;
-
-		if (intel_sdvo_get_supp_encode(intel_output,
-					       &sdvo_priv->encode) &&
-		    intel_sdvo_get_digital_encoding_mode(intel_output) &&
-		    sdvo_priv->is_hdmi) {
-			/* enable hdmi encoding mode if supported */
-			intel_sdvo_set_encode(intel_output, SDVO_ENCODE_HDMI);
-			intel_sdvo_set_colorimetry(intel_output,
-						   SDVO_COLORIMETRY_RGB256);
-			connector_type = DRM_MODE_CONNECTOR_HDMIA;
-		}
-	}
-	else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_SVID0)
-	{
-		sdvo_priv->controlled_output = SDVO_OUTPUT_SVID0;
-		encoder_type = DRM_MODE_ENCODER_TVDAC;
-		connector_type = DRM_MODE_CONNECTOR_SVIDEO;
-		sdvo_priv->is_tv = true;
-		intel_output->needs_tv_clock = true;
-	}
-	else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_RGB0)
-	{
-		sdvo_priv->controlled_output = SDVO_OUTPUT_RGB0;
-		encoder_type = DRM_MODE_ENCODER_DAC;
-		connector_type = DRM_MODE_CONNECTOR_VGA;
-	}
-	else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_RGB1)
-	{
-		sdvo_priv->controlled_output = SDVO_OUTPUT_RGB1;
-		encoder_type = DRM_MODE_ENCODER_DAC;
-		connector_type = DRM_MODE_CONNECTOR_VGA;
-	}
-	else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_LVDS0)
-	{
-		sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS0;
-		encoder_type = DRM_MODE_ENCODER_LVDS;
-		connector_type = DRM_MODE_CONNECTOR_LVDS;
-		sdvo_priv->is_lvds = true;
-	}
-	else if (sdvo_priv->caps.output_flags & SDVO_OUTPUT_LVDS1)
-	{
-		sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS1;
-		encoder_type = DRM_MODE_ENCODER_LVDS;
-		connector_type = DRM_MODE_CONNECTOR_LVDS;
-		sdvo_priv->is_lvds = true;
-	}
-	else
-	{
-		unsigned char bytes[2];
-
-		sdvo_priv->controlled_output = 0;
-		memcpy (bytes, &sdvo_priv->caps.output_flags, 2);
-		DRM_DEBUG_KMS(I915_SDVO,
-				"%s: Unknown SDVO output type (0x%02x%02x)\n",
-				  SDVO_NAME(sdvo_priv),
-				  bytes[0], bytes[1]);
-		encoder_type = DRM_MODE_ENCODER_NONE;
-		connector_type = DRM_MODE_CONNECTOR_Unknown;
+	if (intel_sdvo_output_setup(intel_output,
+				    sdvo_priv->caps.output_flags) != true) {
+		DRM_DEBUG("SDVO output failed to setup on SDVO%c\n",
+			  output_device == SDVOB ? 'B' : 'C');
 		goto err_i2c;
 	}
 
+
 	connector = &intel_output->base;
 	drm_connector_init(dev, connector, &intel_sdvo_connector_funcs,
-			   connector_type);
+			   connector->connector_type);
+
 	drm_connector_helper_add(connector, &intel_sdvo_connector_helper_funcs);
 	connector->interlace_allowed = 0;
 	connector->doublescan_allowed = 0;
 	connector->display_info.subpixel_order = SubPixelHorizontalRGB;
 
-	drm_encoder_init(dev, &intel_output->enc, &intel_sdvo_enc_funcs, encoder_type);
+	drm_encoder_init(dev, &intel_output->enc,
+			&intel_sdvo_enc_funcs, intel_output->enc.encoder_type);
+
 	drm_encoder_helper_add(&intel_output->enc, &intel_sdvo_helper_funcs);
 
 	drm_mode_connector_attach_encoder(&intel_output->base, &intel_output->enc);
-- 
GitLab


From 0c997c0eaac8c68fa23719617484dae29bddaedd Mon Sep 17 00:00:00 2001
From: Lars-Peter Clausen <lars@metafoo.de>
Date: Wed, 22 Jul 2009 00:33:06 +0200
Subject: [PATCH 0239/1153] S3C24XX: GPIO: Fix pin range check in
 s3c_gpiolib_getchip

In the s3c_gpiolib_getchip implementation for s3c24xx the check whether a pin is
in the gpio banks range is reversed. Thus the function returns NULL for valid
pins and the gpio chip if its not valid.

As a result gpio states are not saved/restored properly during suspend/resume.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 arch/arm/mach-s3c2410/include/mach/gpio-core.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-core.h b/arch/arm/mach-s3c2410/include/mach/gpio-core.h
index 8fe192081d3..f8b879a7973 100644
--- a/arch/arm/mach-s3c2410/include/mach/gpio-core.h
+++ b/arch/arm/mach-s3c2410/include/mach/gpio-core.h
@@ -28,7 +28,7 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin)
 		return NULL;
 
 	chip = &s3c24xx_gpios[pin/32];
-	return (S3C2410_GPIO_OFFSET(pin) > chip->chip.ngpio) ? chip : NULL;
+	return (S3C2410_GPIO_OFFSET(pin) < chip->chip.ngpio) ? chip : NULL;
 }
 
 #endif /* __ASM_ARCH_GPIO_CORE_H */
-- 
GitLab


From 1d91e1a296244690461a7c36d71710dfbabbc219 Mon Sep 17 00:00:00 2001
From: Mark Brown <broonie@opensource.wolfsonmicro.com>
Date: Wed, 15 Jul 2009 13:03:34 +0100
Subject: [PATCH 0240/1153] S3C64XX: Fix get_rate() for ARMCLK

If the requested clock is faster than the parent clock then the
parent clock is the closest we can get to the request so we need
to return that instead of the requested clock.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 arch/arm/plat-s3c64xx/s3c6400-clock.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c
index 1debc1f9f98..f8165e62247 100644
--- a/arch/arm/plat-s3c64xx/s3c6400-clock.c
+++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c
@@ -153,7 +153,7 @@ static unsigned long s3c64xx_clk_arm_round_rate(struct clk *clk,
 	u32 div;
 
 	if (parent < rate)
-		return rate;
+		return parent;
 
 	div = (parent / rate) - 1;
 	if (div > armclk_mask)
-- 
GitLab


From 9b71de49b030ad8fd4d13d38571b5c42dc9ed8dd Mon Sep 17 00:00:00 2001
From: Mark Brown <broonie@opensource.wolfsonmicro.com>
Date: Wed, 15 Jul 2009 13:03:35 +0100
Subject: [PATCH 0241/1153] S3C64XX: Fix ARMCLK configuration

The value of armclk_mask needs to be inverted for use as a mask on
the register value when updating ARM_RATIO.

This is critical for cpufreq support, without it attempts to scale
the frequency of the core trash pretty much the entire clock tree.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 arch/arm/plat-s3c64xx/s3c6400-clock.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c
index f8165e62247..febac1950d8 100644
--- a/arch/arm/plat-s3c64xx/s3c6400-clock.c
+++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c
@@ -175,7 +175,7 @@ static int s3c64xx_clk_arm_set_rate(struct clk *clk, unsigned long rate)
 	div = clk_get_rate(clk->parent) / rate;
 
 	val = __raw_readl(S3C_CLK_DIV0);
-	val &= armclk_mask;
+	val &= ~armclk_mask;
 	val |= (div - 1);
 	__raw_writel(val, S3C_CLK_DIV0);
 
-- 
GitLab


From 0e014e92ba93d905bcb39881dce2d38807b90c34 Mon Sep 17 00:00:00 2001
From: Peter Korsgaard <jacmet@sunsite.dk>
Date: Fri, 17 Jul 2009 22:33:37 +0200
Subject: [PATCH 0242/1153] i2c-s3c2410: s3c24xx_i2c_init: don't clobber IICLC
 value

s3c24xx_i2c_init() was overwriting the IICLC value set just above in
s3c24xx_i2c_clockrate() with zero, effectively disabling the platform
line control setting.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/i2c/busses/i2c-s3c2410.c | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c
index 8f42a4536cd..20bb0ceb027 100644
--- a/drivers/i2c/busses/i2c-s3c2410.c
+++ b/drivers/i2c/busses/i2c-s3c2410.c
@@ -763,11 +763,6 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c)
 	dev_info(i2c->dev, "bus frequency set to %d KHz\n", freq);
 	dev_dbg(i2c->dev, "S3C2410_IICCON=0x%02lx\n", iicon);
 
-	/* check for s3c2440 i2c controller  */
-
-	if (s3c24xx_i2c_is2440(i2c))
-		writel(0x0, i2c->regs + S3C2440_IICLC);
-
 	return 0;
 }
 
-- 
GitLab


From 783fd6fa4c144e3f6913e6fed89de10a6dd715a5 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Fri, 17 Jul 2009 15:24:00 +0200
Subject: [PATCH 0243/1153] i2c: strncpy does not null terminate string

strlcpy() will always null terminate the string.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/i2c/busses/i2c-omap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index fdd83277c8a..f2b82ee39ad 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -879,7 +879,7 @@ omap_i2c_probe(struct platform_device *pdev)
 	i2c_set_adapdata(adap, dev);
 	adap->owner = THIS_MODULE;
 	adap->class = I2C_CLASS_HWMON;
-	strncpy(adap->name, "OMAP I2C adapter", sizeof(adap->name));
+	strlcpy(adap->name, "OMAP I2C adapter", sizeof(adap->name));
 	adap->algo = &omap_i2c_algo;
 	adap->dev.parent = &pdev->dev;
 
-- 
GitLab


From ccb3bc16b4891a82649d4bccbeefe60b1d9a62e2 Mon Sep 17 00:00:00 2001
From: Magnus Damm <damm@igel.co.jp>
Date: Wed, 22 Jul 2009 23:58:39 +0900
Subject: [PATCH 0244/1153] i2c-sh_mobile: change module_init() to
 subsys_initcall()

Convert the i2c-sh_mobile i2c bus driver to use
subsys_initcall() instead of module_init().

This change makes the driver register a bit earlier which
together with earlier platform data moves the time for probe().
The earlier probe() makes it possible to use i2c_get_adapter()
and i2c_transfer() from device_initcall().

The same strategy is used by other i2c bus drivers such as
i2c-pxa.c and i2c-s3c2410.c.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
[ben-linux@fluff.org: minor subject updaye]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/i2c/busses/i2c-sh_mobile.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c
index 4f3d99cd169..820487d0d5c 100644
--- a/drivers/i2c/busses/i2c-sh_mobile.c
+++ b/drivers/i2c/busses/i2c-sh_mobile.c
@@ -637,7 +637,7 @@ static void __exit sh_mobile_i2c_adap_exit(void)
 	platform_driver_unregister(&sh_mobile_i2c_driver);
 }
 
-module_init(sh_mobile_i2c_adap_init);
+subsys_initcall(sh_mobile_i2c_adap_init);
 module_exit(sh_mobile_i2c_adap_exit);
 
 MODULE_DESCRIPTION("SuperH Mobile I2C Bus Controller driver");
-- 
GitLab


From bfb6b6588af5ff762222cee79152d2be738ccc06 Mon Sep 17 00:00:00 2001
From: "Sonasath, Moiz" <m-sonasath@ti.com>
Date: Tue, 21 Jul 2009 10:14:06 -0500
Subject: [PATCH 0245/1153] i2c-omap: Bug in reading the RXSTAT/TXSTAT values
 from the I2C_BUFFSTAT register

Fix bug in reading the I2C_BUFFSTAT register for getting byte count on RX/TX interrupt.

On Interrupt: I2C_STAT[RDR],
	read 'RXSTAT' from I2C_BUFFSTAT[8-13]
On Interrupt: I2C_STAT[XDR]
	read 'TXSTAT' from I2C_BUFFSTAT[0-5]

Signed-off-by: Jagadeesh Pakaravoor <j-pakaravoor@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/i2c/busses/i2c-omap.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index f2b82ee39ad..a6966578851 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -692,9 +692,10 @@ omap_i2c_isr(int this_irq, void *dev_id)
 			if (dev->fifo_size) {
 				if (stat & OMAP_I2C_STAT_RRDY)
 					num_bytes = dev->fifo_size;
-				else
-					num_bytes = omap_i2c_read_reg(dev,
-							OMAP_I2C_BUFSTAT_REG);
+				else    /* read RXSTAT on RDR interrupt */
+					num_bytes = (omap_i2c_read_reg(dev,
+							OMAP_I2C_BUFSTAT_REG)
+							>> 8) & 0x3F;
 			}
 			while (num_bytes) {
 				num_bytes--;
@@ -731,9 +732,10 @@ omap_i2c_isr(int this_irq, void *dev_id)
 			if (dev->fifo_size) {
 				if (stat & OMAP_I2C_STAT_XRDY)
 					num_bytes = dev->fifo_size;
-				else
+				else    /* read TXSTAT on XDR interrupt */
 					num_bytes = omap_i2c_read_reg(dev,
-							OMAP_I2C_BUFSTAT_REG);
+							OMAP_I2C_BUFSTAT_REG)
+							& 0x3F;
 			}
 			while (num_bytes) {
 				num_bytes--;
-- 
GitLab


From 04c688dd7a65935568b44629bfaa122eddf76e94 Mon Sep 17 00:00:00 2001
From: "Sonasath, Moiz" <m-sonasath@ti.com>
Date: Tue, 21 Jul 2009 10:14:40 -0500
Subject: [PATCH 0246/1153] i2c-omap: In case of a NACK|ARDY|AL return from the
 ISR

In case of a NACK or ARDY or AL interrupt, complete the request.
There is no need to service the RRDY/RDR or XRDY/XDR interrupts.

Refer TRM SWPU114: Figure 18-31.I2C Master Transmitter Mode, Interrupt Method,
in F/S and HS Modes

http://focus.ti.com/pdfs/wtbu/SWPU114T_PrelimFinalEPDF_06_25_2009.pdf

Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/i2c/busses/i2c-omap.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index a6966578851..5c508ccf438 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -685,8 +685,10 @@ omap_i2c_isr(int this_irq, void *dev_id)
 			err |= OMAP_I2C_STAT_AL;
 		}
 		if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK |
-					OMAP_I2C_STAT_AL))
+					OMAP_I2C_STAT_AL)) {
 			omap_i2c_complete_cmd(dev, err);
+			return IRQ_HANDLED;
+		}
 		if (stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR)) {
 			u8 num_bytes = 1;
 			if (dev->fifo_size) {
-- 
GitLab


From cd086d3aa6f7f7bf4d4e1f9fa09af0f0b6bb99ec Mon Sep 17 00:00:00 2001
From: "Sonasath, Moiz" <m-sonasath@ti.com>
Date: Tue, 21 Jul 2009 10:15:12 -0500
Subject: [PATCH 0247/1153] i2c-omap: OMAP3430 Silicon Errata 1.153

When an XRDY/XDR is hit, wait for XUDF before writing data to DATA_REG.
Otherwise some data bytes can be lost while transferring them from the
memory to the I2C interface.

Do a Busy-wait for XUDF, before writing data to DATA_REG. While waiting
if there is NACK | AL, set the appropriate error flags, ack the pending
interrupts and return from the ISR.

Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/i2c/busses/i2c-omap.c | 24 +++++++++++++++++++++++-
 1 file changed, 23 insertions(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 5c508ccf438..d258b02aef4 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -672,9 +672,10 @@ omap_i2c_isr(int this_irq, void *dev_id)
 			break;
 		}
 
+		err = 0;
+complete:
 		omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, stat);
 
-		err = 0;
 		if (stat & OMAP_I2C_STAT_NACK) {
 			err |= OMAP_I2C_STAT_NACK;
 			omap_i2c_write_reg(dev, OMAP_I2C_CON_REG,
@@ -764,6 +765,27 @@ omap_i2c_isr(int this_irq, void *dev_id)
 							"data to send\n");
 					break;
 				}
+
+				/*
+				 * OMAP3430 Errata 1.153: When an XRDY/XDR
+				 * is hit, wait for XUDF before writing data
+				 * to DATA_REG. Otherwise some data bytes can
+				 * be lost while transferring them from the
+				 * memory to the I2C interface.
+				 */
+
+				if (cpu_is_omap34xx()) {
+						while (!(stat & OMAP_I2C_STAT_XUDF)) {
+							if (stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) {
+								omap_i2c_ack_stat(dev, stat & (OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR));
+								err |= OMAP_I2C_STAT_XUDF;
+								goto complete;
+							}
+							cpu_relax();
+							stat = omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG);
+						}
+				}
+
 				omap_i2c_write_reg(dev, OMAP_I2C_DATA_REG, w);
 			}
 			omap_i2c_ack_stat(dev,
-- 
GitLab


From 51fbb4bab6c8710eb897ab3fb06efbbc921f3a8d Mon Sep 17 00:00:00 2001
From: Matthew Wilcox <matthew@wil.cx>
Date: Wed, 29 Jul 2009 15:02:03 -0700
Subject: [PATCH 0248/1153] markup_oops: fix it with 32-bit userspace on a
 64-bit kernel

A 32-bit perl can't handle 64-bit addresses without using the BigInt
package.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 scripts/markup_oops.pl | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/scripts/markup_oops.pl b/scripts/markup_oops.pl
index 528492bcba5..89774011965 100644
--- a/scripts/markup_oops.pl
+++ b/scripts/markup_oops.pl
@@ -1,6 +1,7 @@
 #!/usr/bin/perl
 
 use File::Basename;
+use Math::BigInt;
 
 # Copyright 2008, Intel Corporation
 #
@@ -172,8 +173,8 @@ while (<STDIN>) {
 	parse_x86_regs($line);
 }
 
-my $decodestart = hex($target) - hex($func_offset);
-my $decodestop = hex($target) + 8192;
+my $decodestart = Math::BigInt->from_hex("0x$target") - Math::BigInt->from_hex("0x$func_offset");
+my $decodestop = Math::BigInt->from_hex("0x$target") + 8192;
 if ($target eq "0") {
 	print "No oops found!\n";
 	print "Usage: \n";
-- 
GitLab


From e084b2d95e48b31aa45f9c49ffc6cdae8bdb21d4 Mon Sep 17 00:00:00 2001
From: Mel Gorman <mel@csn.ul.ie>
Date: Wed, 29 Jul 2009 15:02:04 -0700
Subject: [PATCH 0249/1153] page-allocator: preserve PFN ordering when
 __GFP_COLD is set

Fix a post-2.6.24 performace regression caused by
3dfa5721f12c3d5a441448086bee156887daa961 ("page-allocator: preserve PFN
ordering when __GFP_COLD is set").

Narayanan reports "The regression is around 15%.  There is no disk controller
as our setup is based on Samsung OneNAND used as a memory mapped device on a
OMAP2430 based board."

The page allocator tries to preserve contiguous PFN ordering when returning
pages such that repeated callers to the allocator have a strong chance of
getting physically contiguous pages, particularly when external fragmentation
is low.  However, of the bulk of the allocations have __GFP_COLD set as they
are due to aio_read() for example, then the PFNs are in reverse PFN order.
This can cause performance degration when used with IO controllers that could
have merged the requests.

This patch attempts to preserve the contiguous ordering of PFNs for users of
__GFP_COLD.

Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reported-by: Narayananu Gopalakrishnan <narayanan.g@samsung.com>
Tested-by: Narayanan Gopalakrishnan <narayanan.g@samsung.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 mm/page_alloc.c | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)

diff --git a/mm/page_alloc.c b/mm/page_alloc.c
index caa92689aac..ae28c22a7fd 100644
--- a/mm/page_alloc.c
+++ b/mm/page_alloc.c
@@ -882,7 +882,7 @@ retry_reserve:
  */
 static int rmqueue_bulk(struct zone *zone, unsigned int order, 
 			unsigned long count, struct list_head *list,
-			int migratetype)
+			int migratetype, int cold)
 {
 	int i;
 	
@@ -901,7 +901,10 @@ static int rmqueue_bulk(struct zone *zone, unsigned int order,
 		 * merge IO requests if the physical pages are ordered
 		 * properly.
 		 */
-		list_add(&page->lru, list);
+		if (likely(cold == 0))
+			list_add(&page->lru, list);
+		else
+			list_add_tail(&page->lru, list);
 		set_page_private(page, migratetype);
 		list = &page->lru;
 	}
@@ -1119,7 +1122,8 @@ again:
 		local_irq_save(flags);
 		if (!pcp->count) {
 			pcp->count = rmqueue_bulk(zone, 0,
-					pcp->batch, &pcp->list, migratetype);
+					pcp->batch, &pcp->list,
+					migratetype, cold);
 			if (unlikely(!pcp->count))
 				goto failed;
 		}
@@ -1138,7 +1142,8 @@ again:
 		/* Allocate more to the pcp list if necessary */
 		if (unlikely(&page->lru == &pcp->list)) {
 			pcp->count += rmqueue_bulk(zone, 0,
-					pcp->batch, &pcp->list, migratetype);
+					pcp->batch, &pcp->list,
+					migratetype, cold);
 			page = list_entry(pcp->list.next, struct page, lru);
 		}
 
-- 
GitLab


From 6583bb64fc370842b32a87c67750c26f6d559af0 Mon Sep 17 00:00:00 2001
From: David Rientjes <rientjes@google.com>
Date: Wed, 29 Jul 2009 15:02:06 -0700
Subject: [PATCH 0250/1153] mm: avoid endless looping for oom killed tasks

If a task is oom killed and still cannot find memory when trying with
no watermarks, it's better to fail the allocation attempt than to loop
endlessly.  Direct reclaim has already failed and the oom killer will
be a no-op since current has yet to die, so there is no other
alternative for allocations that are not __GFP_NOFAIL.

Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 mm/page_alloc.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/mm/page_alloc.c b/mm/page_alloc.c
index ae28c22a7fd..2dbb2fc6883 100644
--- a/mm/page_alloc.c
+++ b/mm/page_alloc.c
@@ -1794,6 +1794,10 @@ rebalance:
 	if (p->flags & PF_MEMALLOC)
 		goto nopage;
 
+	/* Avoid allocations with no watermarks from looping endlessly */
+	if (test_thread_flag(TIF_MEMDIE) && !(gfp_mask & __GFP_NOFAIL))
+		goto nopage;
+
 	/* Try direct reclaim and then allocating */
 	page = __alloc_pages_direct_reclaim(gfp_mask, order,
 					zonelist, high_zoneidx,
-- 
GitLab


From 933b787b57ca8bdc0fc8fb2cbf67b5e6d21beb84 Mon Sep 17 00:00:00 2001
From: Rik van Riel <riel@redhat.com>
Date: Wed, 29 Jul 2009 15:02:07 -0700
Subject: [PATCH 0251/1153] mm: copy over oom_adj value at fork time

Fix a post-2.6.31 regression which was introduced by
2ff05b2b4eac2e63d345fc731ea151a060247f53 ("oom: move oom_adj value from
task_struct to mm_struct").

After moving the oom_adj value from the task struct to the mm_struct, the
oom_adj value was no longer properly inherited by child processes.

Copying over the oom_adj value at fork time fixes that bug.

[kosaki.motohiro@jp.fujitsu.com: test for current->mm before dereferencing it]
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Paul Menage <manage@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/fork.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/kernel/fork.c b/kernel/fork.c
index 9b42695f0d1..29b532e718f 100644
--- a/kernel/fork.c
+++ b/kernel/fork.c
@@ -426,6 +426,7 @@ static struct mm_struct * mm_init(struct mm_struct * mm, struct task_struct *p)
 	init_rwsem(&mm->mmap_sem);
 	INIT_LIST_HEAD(&mm->mmlist);
 	mm->flags = (current->mm) ? current->mm->flags : default_dump_filter;
+	mm->oom_adj = (current->mm) ? current->mm->oom_adj : 0;
 	mm->core_state = NULL;
 	mm->nr_ptes = 0;
 	set_mm_counter(mm, file_rss, 0);
-- 
GitLab


From 11c7da4b0ca76a57f51c996c883c480e203cf5a9 Mon Sep 17 00:00:00 2001
From: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Date: Wed, 29 Jul 2009 15:02:08 -0700
Subject: [PATCH 0252/1153] kexec: fix omitting offset in extended crashkernel
 syntax

Setting
 "crashkernel=512M-2G:64M,2G-:128M"
does not work but it turns to work if it has a trailing-whitespace,
like
 "crashkernel=512M-2G:64M,2G-:128M ".

It was because of a bug in the parser, running over the cmdline.

This patch adds a check of the termination.

Reported-by: Jin Dongming <jin.dongming@np.css.fujitsu.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Tested-by: Jin Dongming <jin.dongming@np.css.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/kexec.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/kexec.c b/kernel/kexec.c
index ae1c35201cc..f336e2107f9 100644
--- a/kernel/kexec.c
+++ b/kernel/kexec.c
@@ -1228,7 +1228,7 @@ static int __init parse_crashkernel_mem(char 			*cmdline,
 	} while (*cur++ == ',');
 
 	if (*crash_size > 0) {
-		while (*cur != ' ' && *cur != '@')
+		while (*cur && *cur != ' ' && *cur != '@')
 			cur++;
 		if (*cur == '@') {
 			cur++;
-- 
GitLab


From 3d768213a6c34a27fac1804143da8cf18b8b175f Mon Sep 17 00:00:00 2001
From: Lu Zhihe <tombowfly@gmail.com>
Date: Wed, 29 Jul 2009 15:02:09 -0700
Subject: [PATCH 0253/1153] edac: x38 fix mchbar high register addr

Intel X38 MCHBAR is a 64bits register, base from 0x48, so its higher base
is 0x4C.

Signed-off-by: Lu Zhihe <tombowfly@gmail.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: <stable@kernel.org>		[2.6.30.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/edac/x38_edac.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/edac/x38_edac.c b/drivers/edac/x38_edac.c
index 2406c2ce284..d4ec6059317 100644
--- a/drivers/edac/x38_edac.c
+++ b/drivers/edac/x38_edac.c
@@ -30,7 +30,7 @@
 /* Intel X38 register addresses - device 0 function 0 - DRAM Controller */
 
 #define X38_MCHBAR_LOW	0x48	/* MCH Memory Mapped Register BAR */
-#define X38_MCHBAR_HIGH	0x4b
+#define X38_MCHBAR_HIGH	0x4c
 #define X38_MCHBAR_MASK	0xfffffc000ULL	/* bits 35:14 */
 #define X38_MMR_WINDOW_SIZE	16384
 
-- 
GitLab


From c42b110caeb128819104d057acdaa1ae564b7c8d Mon Sep 17 00:00:00 2001
From: Pawel Osciak <p.osciak@samsung.com>
Date: Wed, 29 Jul 2009 15:02:10 -0700
Subject: [PATCH 0254/1153] s3c-fb: fix off-by-one bug in loop indexes

Fixed off-by-one bug in loop indexes - some elements beyond windows' array
were accessed, which might result in memory access violations when
removing/suspending the device.

Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/video/s3c-fb.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/video/s3c-fb.c b/drivers/video/s3c-fb.c
index bb63c07e13d..5a72083dc67 100644
--- a/drivers/video/s3c-fb.c
+++ b/drivers/video/s3c-fb.c
@@ -964,7 +964,7 @@ static int __devexit s3c_fb_remove(struct platform_device *pdev)
 	struct s3c_fb *sfb = platform_get_drvdata(pdev);
 	int win;
 
-	for (win = 0; win <= S3C_FB_MAX_WIN; win++)
+	for (win = 0; win < S3C_FB_MAX_WIN; win++)
 		if (sfb->windows[win])
 			s3c_fb_release_win(sfb, sfb->windows[win]);
 
@@ -988,7 +988,7 @@ static int s3c_fb_suspend(struct platform_device *pdev, pm_message_t state)
 	struct s3c_fb_win *win;
 	int win_no;
 
-	for (win_no = S3C_FB_MAX_WIN; win_no >= 0; win_no--) {
+	for (win_no = S3C_FB_MAX_WIN - 1; win_no >= 0; win_no--) {
 		win = sfb->windows[win_no];
 		if (!win)
 			continue;
-- 
GitLab


From ddb22195cb3dc5175ba3aac5e957d0e34cd2ee73 Mon Sep 17 00:00:00 2001
From: Jouni Hogander <jouni.hogander@nokia.com>
Date: Wed, 29 Jul 2009 15:02:11 -0700
Subject: [PATCH 0255/1153] spi: omap2_mcspi supports wake events

Currently mcspi wake-ups are not enabled.  This might cause cases where
OMAP is not waking up on mcspi events.

Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/spi/omap2_mcspi.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c
index eee4b6e0af2..2b64091b0f1 100644
--- a/drivers/spi/omap2_mcspi.c
+++ b/drivers/spi/omap2_mcspi.c
@@ -59,6 +59,8 @@
 
 /* per-register bitmasks: */
 
+#define OMAP2_MCSPI_SYSCONFIG_SMARTIDLE	(2 << 3)
+#define OMAP2_MCSPI_SYSCONFIG_ENAWAKEUP	(1 << 2)
 #define OMAP2_MCSPI_SYSCONFIG_AUTOIDLE	(1 << 0)
 #define OMAP2_MCSPI_SYSCONFIG_SOFTRESET	(1 << 1)
 
@@ -90,6 +92,7 @@
 
 #define OMAP2_MCSPI_CHCTRL_EN		(1 << 0)
 
+#define OMAP2_MCSPI_WAKEUPENABLE_WKEN	(1 << 0)
 
 /* We have 2 DMA channels per CS, one for RX and one for TX */
 struct omap2_mcspi_dma {
@@ -873,8 +876,12 @@ static int __init omap2_mcspi_reset(struct omap2_mcspi *mcspi)
 	} while (!(tmp & OMAP2_MCSPI_SYSSTATUS_RESETDONE));
 
 	mcspi_write_reg(master, OMAP2_MCSPI_SYSCONFIG,
-			/* (3 << 8) | (2 << 3) | */
-			OMAP2_MCSPI_SYSCONFIG_AUTOIDLE);
+			OMAP2_MCSPI_SYSCONFIG_AUTOIDLE |
+			OMAP2_MCSPI_SYSCONFIG_ENAWAKEUP |
+			OMAP2_MCSPI_SYSCONFIG_SMARTIDLE);
+
+	mcspi_write_reg(master, OMAP2_MCSPI_WAKEUPENABLE,
+			OMAP2_MCSPI_WAKEUPENABLE_WKEN);
 
 	omap2_mcspi_set_master_mode(master);
 
-- 
GitLab


From 57c5c28dbc835c67a9c23912bab56b7f165e7715 Mon Sep 17 00:00:00 2001
From: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Date: Wed, 29 Jul 2009 15:02:12 -0700
Subject: [PATCH 0256/1153] spi: omap2_mcspi rxdma bugfix

When data is read through DMA, the last element must be read separately
through the RX register.  It cannot be transferred by the DMA.  For
further details see e.g.  OMAP35x TRM (table 19-16).

Without the fix the driver causes extra clocks to be clocked to the bus
after DMA RX operations.  This can cause interesting behaviour with some
devices.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
[aaro.koskinen@nokia.com: Simplified the patch while keeping the idea.]
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/spi/omap2_mcspi.c | 21 ++++++++++++++++++++-
 1 file changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c
index 2b64091b0f1..9b80ad36dbb 100644
--- a/drivers/spi/omap2_mcspi.c
+++ b/drivers/spi/omap2_mcspi.c
@@ -272,7 +272,7 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer)
 
 	if (rx != NULL) {
 		omap_set_dma_transfer_params(mcspi_dma->dma_rx_channel,
-				data_type, element_count, 1,
+				data_type, element_count - 1, 1,
 				OMAP_DMA_SYNC_ELEMENT,
 				mcspi_dma->dma_rx_sync_dev, 1);
 
@@ -303,6 +303,25 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer)
 	if (rx != NULL) {
 		wait_for_completion(&mcspi_dma->dma_rx_completion);
 		dma_unmap_single(NULL, xfer->rx_dma, count, DMA_FROM_DEVICE);
+		omap2_mcspi_set_enable(spi, 0);
+		if (likely(mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHSTAT0)
+				& OMAP2_MCSPI_CHSTAT_RXS)) {
+			u32 w;
+
+			w = mcspi_read_cs_reg(spi, OMAP2_MCSPI_RX0);
+			if (word_len <= 8)
+				((u8 *)xfer->rx_buf)[element_count - 1] = w;
+			else if (word_len <= 16)
+				((u16 *)xfer->rx_buf)[element_count - 1] = w;
+			else /* word_len <= 32 */
+				((u32 *)xfer->rx_buf)[element_count - 1] = w;
+		} else {
+			dev_err(&spi->dev, "DMA RX last word empty");
+			count -= (word_len <= 8)  ? 1 :
+				 (word_len <= 16) ? 2 :
+			       /* word_len <= 32 */ 4;
+		}
+		omap2_mcspi_set_enable(spi, 1);
 	}
 	return count;
 }
-- 
GitLab


From 659098141d02eb8e3545be8969d262e02d2f3f98 Mon Sep 17 00:00:00 2001
From: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Date: Wed, 29 Jul 2009 15:02:13 -0700
Subject: [PATCH 0257/1153] rtc: mark if rtc-cmos drivers were successfully
 registered

rtc-cmos has two drivers, one PNP and one platform.  When PNP has not
succeeded probing, platform is registered.  However, it tries to
unregister both drivers unconditionally, instead of only unregistering
those that were successfully registered.  This causes runtime warnings to
be emitted from the driver core code.

Fix this with a boolean variable for each driver indicating whether
registering was successful.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Cc: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/rtc/rtc-cmos.c | 23 ++++++++++++++++++-----
 1 file changed, 18 insertions(+), 5 deletions(-)

diff --git a/drivers/rtc/rtc-cmos.c b/drivers/rtc/rtc-cmos.c
index 23e10b6263d..f7a4701bf86 100644
--- a/drivers/rtc/rtc-cmos.c
+++ b/drivers/rtc/rtc-cmos.c
@@ -1174,23 +1174,34 @@ static struct platform_driver cmos_platform_driver = {
 	}
 };
 
+#ifdef CONFIG_PNP
+static bool pnp_driver_registered;
+#endif
+static bool platform_driver_registered;
+
 static int __init cmos_init(void)
 {
 	int retval = 0;
 
 #ifdef	CONFIG_PNP
-	pnp_register_driver(&cmos_pnp_driver);
+	retval = pnp_register_driver(&cmos_pnp_driver);
+	if (retval == 0)
+		pnp_driver_registered = true;
 #endif
 
-	if (!cmos_rtc.dev)
+	if (!cmos_rtc.dev) {
 		retval = platform_driver_probe(&cmos_platform_driver,
 					       cmos_platform_probe);
+		if (retval == 0)
+			platform_driver_registered = true;
+	}
 
 	if (retval == 0)
 		return 0;
 
 #ifdef	CONFIG_PNP
-	pnp_unregister_driver(&cmos_pnp_driver);
+	if (pnp_driver_registered)
+		pnp_unregister_driver(&cmos_pnp_driver);
 #endif
 	return retval;
 }
@@ -1199,9 +1210,11 @@ module_init(cmos_init);
 static void __exit cmos_exit(void)
 {
 #ifdef	CONFIG_PNP
-	pnp_unregister_driver(&cmos_pnp_driver);
+	if (pnp_driver_registered)
+		pnp_unregister_driver(&cmos_pnp_driver);
 #endif
-	platform_driver_unregister(&cmos_platform_driver);
+	if (platform_driver_registered)
+		platform_driver_unregister(&cmos_platform_driver);
 }
 module_exit(cmos_exit);
 
-- 
GitLab


From e4c6f8bed01f9f9a5c607bd689bf67e7b8a36bd8 Mon Sep 17 00:00:00 2001
From: Eric Sandeen <sandeen@sandeen.net>
Date: Wed, 29 Jul 2009 15:02:16 -0700
Subject: [PATCH 0258/1153] hugetlbfs: fix i_blocks accounting

As reported in Red Hat bz #509671, i_blocks for files on hugetlbfs get
accounting wrong when doing something like:

   $ > foo
   $ date  > foo
   date: write error: Invalid argument
   $ /usr/bin/stat foo
     File: `foo'
     Size: 0          Blocks: 18446744073709547520 IO Block: 2097152 regular
...

This is because hugetlb_unreserve_pages() is unconditionally removing
blocks_per_huge_page(h) on each call rather than using the freed amount.
If there were 0 blocks, it goes negative, resulting in the above.

This is a regression from commit a5516438959d90b071ff0a484ce4f3f523dc3152
("hugetlb: modular state for hugetlb page size")

which did:

-	inode->i_blocks -= BLOCKS_PER_HUGEPAGE * freed;
+	inode->i_blocks -= blocks_per_huge_page(h);

so just put back the freed multiplier, and it's all happy again.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Andi Kleen <andi@firstfloor.org>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 mm/hugetlb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/mm/hugetlb.c b/mm/hugetlb.c
index d0351e31f47..cafdcee154e 100644
--- a/mm/hugetlb.c
+++ b/mm/hugetlb.c
@@ -2370,7 +2370,7 @@ void hugetlb_unreserve_pages(struct inode *inode, long offset, long freed)
 	long chg = region_truncate(&inode->i_mapping->private_list, offset);
 
 	spin_lock(&inode->i_lock);
-	inode->i_blocks -= blocks_per_huge_page(h);
+	inode->i_blocks -= (blocks_per_huge_page(h) * freed);
 	spin_unlock(&inode->i_lock);
 
 	hugetlb_put_quota(inode->i_mapping, (chg - freed));
-- 
GitLab


From 3fc7b4b220c7e830a5b3ce0ea5f85a635e0c50f0 Mon Sep 17 00:00:00 2001
From: Roland Dreier <rdreier@cisco.com>
Date: Wed, 29 Jul 2009 15:04:02 -0700
Subject: [PATCH 0259/1153] lib: export generic atomic64_t functions

The generic atomic64_t implementation in lib/ did not export the functions
it defined, which means that modules that use atomic64_t would not link on
platforms (such as 32-bit powerpc).  For example, trying to build a kernel
with CONFIG_NET_RDS on such a platform would fail with:

    ERROR: "atomic64_read" [net/rds/rds.ko] undefined!
    ERROR: "atomic64_set" [net/rds/rds.ko] undefined!

Fix this by exporting the atomic64_t functions to modules.  (I export the
entire API even if it's not all currently used by in-tree modules to avoid
having to continue fixing this in dribs and drabs)

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 lib/atomic64.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/lib/atomic64.c b/lib/atomic64.c
index c5e72556241..8bee16ec752 100644
--- a/lib/atomic64.c
+++ b/lib/atomic64.c
@@ -13,6 +13,7 @@
 #include <linux/cache.h>
 #include <linux/spinlock.h>
 #include <linux/init.h>
+#include <linux/module.h>
 #include <asm/atomic.h>
 
 /*
@@ -52,6 +53,7 @@ long long atomic64_read(const atomic64_t *v)
 	spin_unlock_irqrestore(lock, flags);
 	return val;
 }
+EXPORT_SYMBOL(atomic64_read);
 
 void atomic64_set(atomic64_t *v, long long i)
 {
@@ -62,6 +64,7 @@ void atomic64_set(atomic64_t *v, long long i)
 	v->counter = i;
 	spin_unlock_irqrestore(lock, flags);
 }
+EXPORT_SYMBOL(atomic64_set);
 
 void atomic64_add(long long a, atomic64_t *v)
 {
@@ -72,6 +75,7 @@ void atomic64_add(long long a, atomic64_t *v)
 	v->counter += a;
 	spin_unlock_irqrestore(lock, flags);
 }
+EXPORT_SYMBOL(atomic64_add);
 
 long long atomic64_add_return(long long a, atomic64_t *v)
 {
@@ -84,6 +88,7 @@ long long atomic64_add_return(long long a, atomic64_t *v)
 	spin_unlock_irqrestore(lock, flags);
 	return val;
 }
+EXPORT_SYMBOL(atomic64_add_return);
 
 void atomic64_sub(long long a, atomic64_t *v)
 {
@@ -94,6 +99,7 @@ void atomic64_sub(long long a, atomic64_t *v)
 	v->counter -= a;
 	spin_unlock_irqrestore(lock, flags);
 }
+EXPORT_SYMBOL(atomic64_sub);
 
 long long atomic64_sub_return(long long a, atomic64_t *v)
 {
@@ -106,6 +112,7 @@ long long atomic64_sub_return(long long a, atomic64_t *v)
 	spin_unlock_irqrestore(lock, flags);
 	return val;
 }
+EXPORT_SYMBOL(atomic64_sub_return);
 
 long long atomic64_dec_if_positive(atomic64_t *v)
 {
@@ -120,6 +127,7 @@ long long atomic64_dec_if_positive(atomic64_t *v)
 	spin_unlock_irqrestore(lock, flags);
 	return val;
 }
+EXPORT_SYMBOL(atomic64_dec_if_positive);
 
 long long atomic64_cmpxchg(atomic64_t *v, long long o, long long n)
 {
@@ -134,6 +142,7 @@ long long atomic64_cmpxchg(atomic64_t *v, long long o, long long n)
 	spin_unlock_irqrestore(lock, flags);
 	return val;
 }
+EXPORT_SYMBOL(atomic64_cmpxchg);
 
 long long atomic64_xchg(atomic64_t *v, long long new)
 {
@@ -147,6 +156,7 @@ long long atomic64_xchg(atomic64_t *v, long long new)
 	spin_unlock_irqrestore(lock, flags);
 	return val;
 }
+EXPORT_SYMBOL(atomic64_xchg);
 
 int atomic64_add_unless(atomic64_t *v, long long a, long long u)
 {
@@ -162,6 +172,7 @@ int atomic64_add_unless(atomic64_t *v, long long a, long long u)
 	spin_unlock_irqrestore(lock, flags);
 	return ret;
 }
+EXPORT_SYMBOL(atomic64_add_unless);
 
 static int init_atomic64_lock(void)
 {
-- 
GitLab


From b317c833211b7fbf902163de766f09554090e0bf Mon Sep 17 00:00:00 2001
From: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Date: Wed, 29 Jul 2009 15:04:03 -0700
Subject: [PATCH 0260/1153] drivers/video/backlight/jornada720_bl.c: fix build

Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/video/backlight/jornada720_bl.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/video/backlight/jornada720_bl.c b/drivers/video/backlight/jornada720_bl.c
index c3ebb6b41ce..7aed2565c1b 100644
--- a/drivers/video/backlight/jornada720_bl.c
+++ b/drivers/video/backlight/jornada720_bl.c
@@ -72,7 +72,7 @@ static int jornada_bl_update_status(struct backlight_device *bd)
 		if (jornada_ssp_byte(SETBRIGHTNESS) != TXDUMMY) {
 			printk(KERN_INFO "bl : failed to set brightness\n");
 			ret = -ETIMEDOUT;
-			goto out
+			goto out;
 		}
 
 		/* at this point we expect that the mcu has accepted
-- 
GitLab


From 096b7fe012d66ed55e98bc8022405ede0cc80e96 Mon Sep 17 00:00:00 2001
From: Li Zefan <lizf@cn.fujitsu.com>
Date: Wed, 29 Jul 2009 15:04:04 -0700
Subject: [PATCH 0261/1153] cgroups: fix pid namespace bug

The bug was introduced by commit cc31edceee04a7b87f2be48f9489ebb72d264844
("cgroups: convert tasks file to use a seq_file with shared pid array").

We cache a pid array for all threads that are opening the same "tasks"
file, but the pids in the array are always from the namespace of the
last process that opened the file, so all other threads will read pids
from that namespace instead of their own namespaces.

To fix it, we maintain a list of pid arrays, which is keyed by pid_ns.
The list will be of length 1 at most time.

Reported-by: Paul Menage <menage@google.com>
Idea-by: Paul Menage <menage@google.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Reviewed-by: Serge Hallyn <serue@us.ibm.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/cgroup.h | 11 ++---
 kernel/cgroup.c        | 96 +++++++++++++++++++++++++++++++-----------
 2 files changed, 76 insertions(+), 31 deletions(-)

diff --git a/include/linux/cgroup.h b/include/linux/cgroup.h
index 665fa70e409..20411d2876f 100644
--- a/include/linux/cgroup.h
+++ b/include/linux/cgroup.h
@@ -179,14 +179,11 @@ struct cgroup {
 	 */
 	struct list_head release_list;
 
-	/* pids_mutex protects the fields below */
+	/* pids_mutex protects pids_list and cached pid arrays. */
 	struct rw_semaphore pids_mutex;
-	/* Array of process ids in the cgroup */
-	pid_t *tasks_pids;
-	/* How many files are using the current tasks_pids array */
-	int pids_use_count;
-	/* Length of the current tasks_pids array */
-	int pids_length;
+
+	/* Linked list of struct cgroup_pids */
+	struct list_head pids_list;
 
 	/* For RCU-protected deletion */
 	struct rcu_head rcu_head;
diff --git a/kernel/cgroup.c b/kernel/cgroup.c
index 3737a682cdf..250dac05680 100644
--- a/kernel/cgroup.c
+++ b/kernel/cgroup.c
@@ -47,6 +47,7 @@
 #include <linux/hash.h>
 #include <linux/namei.h>
 #include <linux/smp_lock.h>
+#include <linux/pid_namespace.h>
 
 #include <asm/atomic.h>
 
@@ -960,6 +961,7 @@ static void init_cgroup_housekeeping(struct cgroup *cgrp)
 	INIT_LIST_HEAD(&cgrp->children);
 	INIT_LIST_HEAD(&cgrp->css_sets);
 	INIT_LIST_HEAD(&cgrp->release_list);
+	INIT_LIST_HEAD(&cgrp->pids_list);
 	init_rwsem(&cgrp->pids_mutex);
 }
 static void init_cgroup_root(struct cgroupfs_root *root)
@@ -2201,12 +2203,30 @@ err:
 	return ret;
 }
 
+/*
+ * Cache pids for all threads in the same pid namespace that are
+ * opening the same "tasks" file.
+ */
+struct cgroup_pids {
+	/* The node in cgrp->pids_list */
+	struct list_head list;
+	/* The cgroup those pids belong to */
+	struct cgroup *cgrp;
+	/* The namepsace those pids belong to */
+	struct pid_namespace *ns;
+	/* Array of process ids in the cgroup */
+	pid_t *tasks_pids;
+	/* How many files are using the this tasks_pids array */
+	int use_count;
+	/* Length of the current tasks_pids array */
+	int length;
+};
+
 static int cmppid(const void *a, const void *b)
 {
 	return *(pid_t *)a - *(pid_t *)b;
 }
 
-
 /*
  * seq_file methods for the "tasks" file. The seq_file position is the
  * next pid to display; the seq_file iterator is a pointer to the pid
@@ -2221,45 +2241,47 @@ static void *cgroup_tasks_start(struct seq_file *s, loff_t *pos)
 	 * after a seek to the start). Use a binary-search to find the
 	 * next pid to display, if any
 	 */
-	struct cgroup *cgrp = s->private;
+	struct cgroup_pids *cp = s->private;
+	struct cgroup *cgrp = cp->cgrp;
 	int index = 0, pid = *pos;
 	int *iter;
 
 	down_read(&cgrp->pids_mutex);
 	if (pid) {
-		int end = cgrp->pids_length;
+		int end = cp->length;
 
 		while (index < end) {
 			int mid = (index + end) / 2;
-			if (cgrp->tasks_pids[mid] == pid) {
+			if (cp->tasks_pids[mid] == pid) {
 				index = mid;
 				break;
-			} else if (cgrp->tasks_pids[mid] <= pid)
+			} else if (cp->tasks_pids[mid] <= pid)
 				index = mid + 1;
 			else
 				end = mid;
 		}
 	}
 	/* If we're off the end of the array, we're done */
-	if (index >= cgrp->pids_length)
+	if (index >= cp->length)
 		return NULL;
 	/* Update the abstract position to be the actual pid that we found */
-	iter = cgrp->tasks_pids + index;
+	iter = cp->tasks_pids + index;
 	*pos = *iter;
 	return iter;
 }
 
 static void cgroup_tasks_stop(struct seq_file *s, void *v)
 {
-	struct cgroup *cgrp = s->private;
+	struct cgroup_pids *cp = s->private;
+	struct cgroup *cgrp = cp->cgrp;
 	up_read(&cgrp->pids_mutex);
 }
 
 static void *cgroup_tasks_next(struct seq_file *s, void *v, loff_t *pos)
 {
-	struct cgroup *cgrp = s->private;
+	struct cgroup_pids *cp = s->private;
 	int *p = v;
-	int *end = cgrp->tasks_pids + cgrp->pids_length;
+	int *end = cp->tasks_pids + cp->length;
 
 	/*
 	 * Advance to the next pid in the array. If this goes off the
@@ -2286,26 +2308,33 @@ static struct seq_operations cgroup_tasks_seq_operations = {
 	.show = cgroup_tasks_show,
 };
 
-static void release_cgroup_pid_array(struct cgroup *cgrp)
+static void release_cgroup_pid_array(struct cgroup_pids *cp)
 {
+	struct cgroup *cgrp = cp->cgrp;
+
 	down_write(&cgrp->pids_mutex);
-	BUG_ON(!cgrp->pids_use_count);
-	if (!--cgrp->pids_use_count) {
-		kfree(cgrp->tasks_pids);
-		cgrp->tasks_pids = NULL;
-		cgrp->pids_length = 0;
+	BUG_ON(!cp->use_count);
+	if (!--cp->use_count) {
+		list_del(&cp->list);
+		put_pid_ns(cp->ns);
+		kfree(cp->tasks_pids);
+		kfree(cp);
 	}
 	up_write(&cgrp->pids_mutex);
 }
 
 static int cgroup_tasks_release(struct inode *inode, struct file *file)
 {
-	struct cgroup *cgrp = __d_cgrp(file->f_dentry->d_parent);
+	struct seq_file *seq;
+	struct cgroup_pids *cp;
 
 	if (!(file->f_mode & FMODE_READ))
 		return 0;
 
-	release_cgroup_pid_array(cgrp);
+	seq = file->private_data;
+	cp = seq->private;
+
+	release_cgroup_pid_array(cp);
 	return seq_release(inode, file);
 }
 
@@ -2324,6 +2353,8 @@ static struct file_operations cgroup_tasks_operations = {
 static int cgroup_tasks_open(struct inode *unused, struct file *file)
 {
 	struct cgroup *cgrp = __d_cgrp(file->f_dentry->d_parent);
+	struct pid_namespace *ns = current->nsproxy->pid_ns;
+	struct cgroup_pids *cp;
 	pid_t *pidarray;
 	int npids;
 	int retval;
@@ -2350,20 +2381,37 @@ static int cgroup_tasks_open(struct inode *unused, struct file *file)
 	 * array if necessary
 	 */
 	down_write(&cgrp->pids_mutex);
-	kfree(cgrp->tasks_pids);
-	cgrp->tasks_pids = pidarray;
-	cgrp->pids_length = npids;
-	cgrp->pids_use_count++;
+
+	list_for_each_entry(cp, &cgrp->pids_list, list) {
+		if (ns == cp->ns)
+			goto found;
+	}
+
+	cp = kzalloc(sizeof(*cp), GFP_KERNEL);
+	if (!cp) {
+		up_write(&cgrp->pids_mutex);
+		kfree(pidarray);
+		return -ENOMEM;
+	}
+	cp->cgrp = cgrp;
+	cp->ns = ns;
+	get_pid_ns(ns);
+	list_add(&cp->list, &cgrp->pids_list);
+found:
+	kfree(cp->tasks_pids);
+	cp->tasks_pids = pidarray;
+	cp->length = npids;
+	cp->use_count++;
 	up_write(&cgrp->pids_mutex);
 
 	file->f_op = &cgroup_tasks_operations;
 
 	retval = seq_open(file, &cgroup_tasks_seq_operations);
 	if (retval) {
-		release_cgroup_pid_array(cgrp);
+		release_cgroup_pid_array(cp);
 		return retval;
 	}
-	((struct seq_file *)file->private_data)->private = cgrp;
+	((struct seq_file *)file->private_data)->private = cp;
 	return 0;
 }
 
-- 
GitLab


From f0d83679a8d471dc8b646919f70595d6fe8c9606 Mon Sep 17 00:00:00 2001
From: Sebastian Heutling <heutling@who-ing.de>
Date: Wed, 29 Jul 2009 15:04:05 -0700
Subject: [PATCH 0262/1153] eeprom/at25: bugfix "not ready" timeout after write

Under certain circumstances msleep(1) within the loop, which waits for the
EEPROM to be finished, might take longer than the timeout.  On the next
loop the status register might now return to be ready and therefore the
loop finishes.  The following check now tests if a timeout occurred and if
so returns an error although the device reported it was ready.

This fix replaces testing the occurrence of the timeout by testing the
"not ready" bit in the status register.

Signed-off-by: Sebastian Heutling <heutling@who-ing.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/misc/eeprom/at25.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/misc/eeprom/at25.c b/drivers/misc/eeprom/at25.c
index b34cb5f79ee..2e535a0ccd5 100644
--- a/drivers/misc/eeprom/at25.c
+++ b/drivers/misc/eeprom/at25.c
@@ -173,6 +173,7 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off,
 		unsigned	segment;
 		unsigned	offset = (unsigned) off;
 		u8		*cp = bounce + 1;
+		int		sr;
 
 		*cp = AT25_WREN;
 		status = spi_write(at25->spi, cp, 1);
@@ -214,7 +215,6 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off,
 		timeout = jiffies + msecs_to_jiffies(EE_TIMEOUT);
 		retries = 0;
 		do {
-			int	sr;
 
 			sr = spi_w8r8(at25->spi, AT25_RDSR);
 			if (sr < 0 || (sr & AT25_SR_nRDY)) {
@@ -228,7 +228,7 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off,
 				break;
 		} while (retries++ < 3 || time_before_eq(jiffies, timeout));
 
-		if (time_after(jiffies, timeout)) {
+		if ((sr < 0) || (sr & AT25_SR_nRDY)) {
 			dev_err(&at25->spi->dev,
 				"write %d bytes offset %d, "
 				"timeout after %u msecs\n",
-- 
GitLab


From 887032670d47366a8c8f25396ea7c14b7b2cc620 Mon Sep 17 00:00:00 2001
From: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Date: Wed, 29 Jul 2009 15:04:06 -0700
Subject: [PATCH 0263/1153] cgroup avoid permanent sleep at rmdir

After commit ec64f51545fffbc4cb968f0cea56341a4b07e85a ("cgroup: fix
frequent -EBUSY at rmdir"), cgroup's rmdir (especially against memcg)
doesn't return -EBUSY by temporary ref counts.  That commit expects all
refs after pre_destroy() is temporary but...it wasn't.  Then, rmdir can
wait permanently.  This patch tries to fix that and change followings.

 - set CGRP_WAIT_ON_RMDIR flag before pre_destroy().
 - clear CGRP_WAIT_ON_RMDIR flag when the subsys finds racy case.
   if there are sleeping ones, wakes them up.
 - rmdir() sleeps only when CGRP_WAIT_ON_RMDIR flag is set.

Tested-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Reported-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Reviewed-by: Paul Menage <menage@google.com>
Acked-by: Balbir Sigh <balbir@linux.vnet.ibm.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/cgroup.h | 17 +++++++++++++
 kernel/cgroup.c        | 55 +++++++++++++++++++++++++++++-------------
 mm/memcontrol.c        | 23 +++++++++++++++---
 3 files changed, 75 insertions(+), 20 deletions(-)

diff --git a/include/linux/cgroup.h b/include/linux/cgroup.h
index 20411d2876f..90bba9e6228 100644
--- a/include/linux/cgroup.h
+++ b/include/linux/cgroup.h
@@ -362,6 +362,23 @@ int cgroup_task_count(const struct cgroup *cgrp);
 /* Return true if cgrp is a descendant of the task's cgroup */
 int cgroup_is_descendant(const struct cgroup *cgrp, struct task_struct *task);
 
+/*
+ * When the subsys has to access css and may add permanent refcnt to css,
+ * it should take care of racy conditions with rmdir(). Following set of
+ * functions, is for stop/restart rmdir if necessary.
+ * Because these will call css_get/put, "css" should be alive css.
+ *
+ *  cgroup_exclude_rmdir();
+ *  ...do some jobs which may access arbitrary empty cgroup
+ *  cgroup_release_and_wakeup_rmdir();
+ *
+ *  When someone removes a cgroup while cgroup_exclude_rmdir() holds it,
+ *  it sleeps and cgroup_release_and_wakeup_rmdir() will wake him up.
+ */
+
+void cgroup_exclude_rmdir(struct cgroup_subsys_state *css);
+void cgroup_release_and_wakeup_rmdir(struct cgroup_subsys_state *css);
+
 /*
  * Control Group subsystem type.
  * See Documentation/cgroups/cgroups.txt for details
diff --git a/kernel/cgroup.c b/kernel/cgroup.c
index 250dac05680..b6eadfe30e7 100644
--- a/kernel/cgroup.c
+++ b/kernel/cgroup.c
@@ -735,16 +735,28 @@ static void cgroup_d_remove_dir(struct dentry *dentry)
  * reference to css->refcnt. In general, this refcnt is expected to goes down
  * to zero, soon.
  *
- * CGRP_WAIT_ON_RMDIR flag is modified under cgroup's inode->i_mutex;
+ * CGRP_WAIT_ON_RMDIR flag is set under cgroup's inode->i_mutex;
  */
 DECLARE_WAIT_QUEUE_HEAD(cgroup_rmdir_waitq);
 
-static void cgroup_wakeup_rmdir_waiters(const struct cgroup *cgrp)
+static void cgroup_wakeup_rmdir_waiter(struct cgroup *cgrp)
 {
-	if (unlikely(test_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags)))
+	if (unlikely(test_and_clear_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags)))
 		wake_up_all(&cgroup_rmdir_waitq);
 }
 
+void cgroup_exclude_rmdir(struct cgroup_subsys_state *css)
+{
+	css_get(css);
+}
+
+void cgroup_release_and_wakeup_rmdir(struct cgroup_subsys_state *css)
+{
+	cgroup_wakeup_rmdir_waiter(css->cgroup);
+	css_put(css);
+}
+
+
 static int rebind_subsystems(struct cgroupfs_root *root,
 			      unsigned long final_bits)
 {
@@ -1359,7 +1371,7 @@ int cgroup_attach_task(struct cgroup *cgrp, struct task_struct *tsk)
 	 * wake up rmdir() waiter. the rmdir should fail since the cgroup
 	 * is no longer empty.
 	 */
-	cgroup_wakeup_rmdir_waiters(cgrp);
+	cgroup_wakeup_rmdir_waiter(cgrp);
 	return 0;
 }
 
@@ -2743,34 +2755,43 @@ again:
 	}
 	mutex_unlock(&cgroup_mutex);
 
+	/*
+	 * In general, subsystem has no css->refcnt after pre_destroy(). But
+	 * in racy cases, subsystem may have to get css->refcnt after
+	 * pre_destroy() and it makes rmdir return with -EBUSY. This sometimes
+	 * make rmdir return -EBUSY too often. To avoid that, we use waitqueue
+	 * for cgroup's rmdir. CGRP_WAIT_ON_RMDIR is for synchronizing rmdir
+	 * and subsystem's reference count handling. Please see css_get/put
+	 * and css_tryget() and cgroup_wakeup_rmdir_waiter() implementation.
+	 */
+	set_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags);
+
 	/*
 	 * Call pre_destroy handlers of subsys. Notify subsystems
 	 * that rmdir() request comes.
 	 */
 	ret = cgroup_call_pre_destroy(cgrp);
-	if (ret)
+	if (ret) {
+		clear_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags);
 		return ret;
+	}
 
 	mutex_lock(&cgroup_mutex);
 	parent = cgrp->parent;
 	if (atomic_read(&cgrp->count) || !list_empty(&cgrp->children)) {
+		clear_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags);
 		mutex_unlock(&cgroup_mutex);
 		return -EBUSY;
 	}
-	/*
-	 * css_put/get is provided for subsys to grab refcnt to css. In typical
-	 * case, subsystem has no reference after pre_destroy(). But, under
-	 * hierarchy management, some *temporal* refcnt can be hold.
-	 * To avoid returning -EBUSY to a user, waitqueue is used. If subsys
-	 * is really busy, it should return -EBUSY at pre_destroy(). wake_up
-	 * is called when css_put() is called and refcnt goes down to 0.
-	 */
-	set_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags);
 	prepare_to_wait(&cgroup_rmdir_waitq, &wait, TASK_INTERRUPTIBLE);
-
 	if (!cgroup_clear_css_refs(cgrp)) {
 		mutex_unlock(&cgroup_mutex);
-		schedule();
+		/*
+		 * Because someone may call cgroup_wakeup_rmdir_waiter() before
+		 * prepare_to_wait(), we need to check this flag.
+		 */
+		if (test_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags))
+			schedule();
 		finish_wait(&cgroup_rmdir_waitq, &wait);
 		clear_bit(CGRP_WAIT_ON_RMDIR, &cgrp->flags);
 		if (signal_pending(current))
@@ -3342,7 +3363,7 @@ void __css_put(struct cgroup_subsys_state *css)
 			set_bit(CGRP_RELEASABLE, &cgrp->flags);
 			check_for_release(cgrp);
 		}
-		cgroup_wakeup_rmdir_waiters(cgrp);
+		cgroup_wakeup_rmdir_waiter(cgrp);
 	}
 	rcu_read_unlock();
 }
diff --git a/mm/memcontrol.c b/mm/memcontrol.c
index e717964cb5a..fd4529d86de 100644
--- a/mm/memcontrol.c
+++ b/mm/memcontrol.c
@@ -1207,6 +1207,12 @@ static int mem_cgroup_move_account(struct page_cgroup *pc,
 	ret = 0;
 out:
 	unlock_page_cgroup(pc);
+	/*
+	 * We charges against "to" which may not have any tasks. Then, "to"
+	 * can be under rmdir(). But in current implementation, caller of
+	 * this function is just force_empty() and it's garanteed that
+	 * "to" is never removed. So, we don't check rmdir status here.
+	 */
 	return ret;
 }
 
@@ -1428,6 +1434,7 @@ __mem_cgroup_commit_charge_swapin(struct page *page, struct mem_cgroup *ptr,
 		return;
 	if (!ptr)
 		return;
+	cgroup_exclude_rmdir(&ptr->css);
 	pc = lookup_page_cgroup(page);
 	mem_cgroup_lru_del_before_commit_swapcache(page);
 	__mem_cgroup_commit_charge(ptr, pc, ctype);
@@ -1457,8 +1464,12 @@ __mem_cgroup_commit_charge_swapin(struct page *page, struct mem_cgroup *ptr,
 		}
 		rcu_read_unlock();
 	}
-	/* add this page(page_cgroup) to the LRU we want. */
-
+	/*
+	 * At swapin, we may charge account against cgroup which has no tasks.
+	 * So, rmdir()->pre_destroy() can be called while we do this charge.
+	 * In that case, we need to call pre_destroy() again. check it here.
+	 */
+	cgroup_release_and_wakeup_rmdir(&ptr->css);
 }
 
 void mem_cgroup_commit_charge_swapin(struct page *page, struct mem_cgroup *ptr)
@@ -1664,7 +1675,7 @@ void mem_cgroup_end_migration(struct mem_cgroup *mem,
 
 	if (!mem)
 		return;
-
+	cgroup_exclude_rmdir(&mem->css);
 	/* at migration success, oldpage->mapping is NULL. */
 	if (oldpage->mapping) {
 		target = oldpage;
@@ -1704,6 +1715,12 @@ void mem_cgroup_end_migration(struct mem_cgroup *mem,
 	 */
 	if (ctype == MEM_CGROUP_CHARGE_TYPE_MAPPED)
 		mem_cgroup_uncharge_page(target);
+	/*
+	 * At migration, we may charge account against cgroup which has no tasks
+	 * So, rmdir()->pre_destroy() can be called while we do this charge.
+	 * In that case, we need to call pre_destroy() again. check it here.
+	 */
+	cgroup_release_and_wakeup_rmdir(&mem->css);
 }
 
 /*
-- 
GitLab


From 1fc28b70fe2dbf87e061b6ce5091a1f8e4e5d4e7 Mon Sep 17 00:00:00 2001
From: Mel Gorman <mel@csn.ul.ie>
Date: Wed, 29 Jul 2009 15:04:08 -0700
Subject: [PATCH 0264/1153] page-allocator: allow too high-order warning
 messages to be suppressed with __GFP_NOWARN

The page allocator warns once when an order >= MAX_ORDER is specified.
This is to catch callers of the allocator that are always falling back to
their worst-case when it was not expected.  However, there are cases where
the caller is behaving correctly but cannot suppress the warning.  This
patch allows the warning to be suppressed by the callers by specifying
__GFP_NOWARN.

Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 mm/page_alloc.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/mm/page_alloc.c b/mm/page_alloc.c
index 2dbb2fc6883..d052abbe306 100644
--- a/mm/page_alloc.c
+++ b/mm/page_alloc.c
@@ -1745,8 +1745,10 @@ __alloc_pages_slowpath(gfp_t gfp_mask, unsigned int order,
 	 * be using allocators in order of preference for an area that is
 	 * too large.
 	 */
-	if (WARN_ON_ONCE(order >= MAX_ORDER))
+	if (order >= MAX_ORDER) {
+		WARN_ON_ONCE(!(gfp_mask & __GFP_NOWARN));
 		return NULL;
+	}
 
 	/*
 	 * GFP_THISNODE (meaning __GFP_THISNODE, __GFP_NORETRY and
-- 
GitLab


From b62f495dad04fa94b5083aec638ff3072bccaaca Mon Sep 17 00:00:00 2001
From: Mel Gorman <mel@csn.ul.ie>
Date: Wed, 29 Jul 2009 15:04:09 -0700
Subject: [PATCH 0265/1153] profile: suppress warning about large allocations
 when profile=1 is specified

When profile= is used, a large buffer is allocated early at boot.  This
can be larger than what the page allocator can provide so it prints a
warning.  However, the caller is able to handle the situation so this
patch suppresses the warning.

Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/profile.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/kernel/profile.c b/kernel/profile.c
index 69911b5745e..419250ebec4 100644
--- a/kernel/profile.c
+++ b/kernel/profile.c
@@ -117,11 +117,12 @@ int __ref profile_init(void)
 
 	cpumask_copy(prof_cpu_mask, cpu_possible_mask);
 
-	prof_buffer = kzalloc(buffer_bytes, GFP_KERNEL);
+	prof_buffer = kzalloc(buffer_bytes, GFP_KERNEL|__GFP_NOWARN);
 	if (prof_buffer)
 		return 0;
 
-	prof_buffer = alloc_pages_exact(buffer_bytes, GFP_KERNEL|__GFP_ZERO);
+	prof_buffer = alloc_pages_exact(buffer_bytes,
+					GFP_KERNEL|__GFP_ZERO|__GFP_NOWARN);
 	if (prof_buffer)
 		return 0;
 
-- 
GitLab


From 1c29b3ff4f2d847464f7be3a0e179c6dfc69bd02 Mon Sep 17 00:00:00 2001
From: Mel Gorman <mel@csn.ul.ie>
Date: Wed, 29 Jul 2009 15:04:10 -0700
Subject: [PATCH 0266/1153] net-dccp: suppress warning about large allocations
 from DCCP

The DCCP protocol tries to allocate some large hash tables during
initialisation using the largest size possible.  This can be larger than
what the page allocator can provide so it prints a warning.  However, the
caller is able to handle the situation so this patch suppresses the
warning.

Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 net/dccp/proto.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/net/dccp/proto.c b/net/dccp/proto.c
index 94ca8eaace7..3281013ce03 100644
--- a/net/dccp/proto.c
+++ b/net/dccp/proto.c
@@ -1066,7 +1066,7 @@ static int __init dccp_init(void)
 		       (dccp_hashinfo.ehash_size - 1))
 			dccp_hashinfo.ehash_size--;
 		dccp_hashinfo.ehash = (struct inet_ehash_bucket *)
-			__get_free_pages(GFP_ATOMIC, ehash_order);
+			__get_free_pages(GFP_ATOMIC|__GFP_NOWARN, ehash_order);
 	} while (!dccp_hashinfo.ehash && --ehash_order > 0);
 
 	if (!dccp_hashinfo.ehash) {
@@ -1091,7 +1091,7 @@ static int __init dccp_init(void)
 		    bhash_order > 0)
 			continue;
 		dccp_hashinfo.bhash = (struct inet_bind_hashbucket *)
-			__get_free_pages(GFP_ATOMIC, bhash_order);
+			__get_free_pages(GFP_ATOMIC|__GFP_NOWARN, bhash_order);
 	} while (!dccp_hashinfo.bhash && --bhash_order >= 0);
 
 	if (!dccp_hashinfo.bhash) {
-- 
GitLab


From 5c8053652328693d10551131432ef3573e77ed2d Mon Sep 17 00:00:00 2001
From: Catalin Marinas <catalin.marinas@arm.com>
Date: Wed, 29 Jul 2009 15:04:11 -0700
Subject: [PATCH 0267/1153] fs/ramfs/file-nommu.c needs include/linux/sched.h

This file makes use of various macros defined in files like asm/current.h
or asm-generic/resource.h.  All these files can be included via sched.h.
The building of the !MMU ARM kernel (with additional patches) fails
without this change.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/ramfs/file-nommu.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/fs/ramfs/file-nommu.c b/fs/ramfs/file-nommu.c
index ebb2c417912..11f0c06316d 100644
--- a/fs/ramfs/file-nommu.c
+++ b/fs/ramfs/file-nommu.c
@@ -20,6 +20,7 @@
 #include <linux/ramfs.h>
 #include <linux/pagevec.h>
 #include <linux/mman.h>
+#include <linux/sched.h>
 
 #include <asm/uaccess.h>
 #include "internal.h"
-- 
GitLab


From f5a55efa140f5e9c9dd0f398fef54f20cdb74ec9 Mon Sep 17 00:00:00 2001
From: Dave Jones <davej@redhat.com>
Date: Wed, 29 Jul 2009 15:04:12 -0700
Subject: [PATCH 0268/1153] pps.h needs <linux/types.h>

Found with make headers_check

/usr/include/linux/pps.h:52: found __[us]{8,16,32,64} type without #include <linux/types.h>

Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/pps.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/include/linux/pps.h b/include/linux/pps.h
index cfe5c7214ec..0194ab06177 100644
--- a/include/linux/pps.h
+++ b/include/linux/pps.h
@@ -22,6 +22,8 @@
 #ifndef _PPS_H_
 #define _PPS_H_
 
+#include <linux/types.h>
+
 #define PPS_VERSION		"5.3.6"
 #define PPS_MAX_SOURCES		16		/* should be enough... */
 
-- 
GitLab


From cab8bd3410d448279e3bd0fbf96d31db0bf770fa Mon Sep 17 00:00:00 2001
From: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Date: Wed, 29 Jul 2009 15:04:14 -0700
Subject: [PATCH 0269/1153] sysrq, kdump: make sysrq-c consistent

commit d6580a9f15238b87e618310c862231ae3f352d2d ("kexec: sysrq: simplify
sysrq-c handler") changed the behavior of sysrq-c to unconditional
dereference of NULL pointer.  So in cases with CONFIG_KEXEC, where
crash_kexec() was directly called from sysrq-c before, now it can be said
that a step of "real oops" was inserted before starting kdump.

However, in contrast to oops via SysRq-c from keyboard which results in
panic due to in_interrupt(), oops via "echo c > /proc/sysrq-trigger" will
not become panic unless panic_on_oops=1.  It means that even if dump is
properly configured to be taken on panic, the sysrq-c from proc interface
might not start crashdump while the sysrq-c from keyboard can start
crashdump.  This confuses traditional users of kdump, i.e.  people who
expect sysrq-c to do common behavior in both of the keyboard and proc
interface.

This patch brings the keyboard and proc interface behavior of sysrq-c in
line, by forcing panic_on_oops=1 before oops in sysrq-c handler.

And some updates in documentation are included, to clarify that there is
no longer dependency with CONFIG_KEXEC, and that now the system can just
crash by sysrq-c if no dump mechanism is configured.

Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Brayan Arraes <brayan@yack.com.br>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 Documentation/sysrq.txt | 7 ++++---
 drivers/char/sysrq.c    | 8 +++++---
 2 files changed, 9 insertions(+), 6 deletions(-)

diff --git a/Documentation/sysrq.txt b/Documentation/sysrq.txt
index cf42b820ff9..d56a0177542 100644
--- a/Documentation/sysrq.txt
+++ b/Documentation/sysrq.txt
@@ -66,7 +66,8 @@ On all -  write a character to /proc/sysrq-trigger.  e.g.:
 'b'     - Will immediately reboot the system without syncing or unmounting
           your disks.
 
-'c'	- Will perform a kexec reboot in order to take a crashdump.
+'c'	- Will perform a system crash by a NULL pointer dereference.
+          A crashdump will be taken if configured.
 
 'd'	- Shows all locks that are held.
 
@@ -141,8 +142,8 @@ useful when you want to exit a program that will not let you switch consoles.
 re'B'oot is good when you're unable to shut down. But you should also 'S'ync
 and 'U'mount first.
 
-'C'rashdump can be used to manually trigger a crashdump when the system is hung.
-The kernel needs to have been built with CONFIG_KEXEC enabled.
+'C'rash can be used to manually trigger a crashdump when the system is hung.
+Note that this just triggers a crash if there is no dump mechanism available.
 
 'S'ync is great when your system is locked up, it allows you to sync your
 disks and will certainly lessen the chance of data loss and fscking. Note
diff --git a/drivers/char/sysrq.c b/drivers/char/sysrq.c
index 0db35857e4d..5d7a02f63e1 100644
--- a/drivers/char/sysrq.c
+++ b/drivers/char/sysrq.c
@@ -35,7 +35,6 @@
 #include <linux/spinlock.h>
 #include <linux/vt_kern.h>
 #include <linux/workqueue.h>
-#include <linux/kexec.h>
 #include <linux/hrtimer.h>
 #include <linux/oom.h>
 
@@ -124,9 +123,12 @@ static struct sysrq_key_op sysrq_unraw_op = {
 static void sysrq_handle_crash(int key, struct tty_struct *tty)
 {
 	char *killer = NULL;
+
+	panic_on_oops = 1;	/* force panic */
+	wmb();
 	*killer = 1;
 }
-static struct sysrq_key_op sysrq_crashdump_op = {
+static struct sysrq_key_op sysrq_crash_op = {
 	.handler	= sysrq_handle_crash,
 	.help_msg	= "Crash",
 	.action_msg	= "Trigger a crash",
@@ -401,7 +403,7 @@ static struct sysrq_key_op *sysrq_key_table[36] = {
 	 */
 	NULL,				/* a */
 	&sysrq_reboot_op,		/* b */
-	&sysrq_crashdump_op,		/* c & ibm_emac driver debug */
+	&sysrq_crash_op,		/* c & ibm_emac driver debug */
 	&sysrq_showlocks_op,		/* d */
 	&sysrq_term_op,			/* e */
 	&sysrq_moom_op,			/* f */
-- 
GitLab


From a9e58f25734e153b8c6516d904e2398fb8b0b23d Mon Sep 17 00:00:00 2001
From: Anton Vorontsov <avorontsov@ru.mvista.com>
Date: Wed, 29 Jul 2009 15:04:16 -0700
Subject: [PATCH 0270/1153] sdhci: get rid of "frequency too high" flood when
 using eSDHC

Since commit 8dfd0374be84793360db7fff2e635d2cd3bbcb21 ("MMC core: limit
minimum initialization frequency to 400kHz") MMC core checks for minimum
frequency, and that causes following messages flood when using eSDHC
controllers:

  ...
  mmc0: Minimum clock frequency too high for identification mode
  mmc0: Minimum clock frequency too high for identification mode
  ...

The warnings are legitimate, since if we'd use 133 MHz clocks for standard
SDHCI controllers, we'd not able to scale frequency down to 400 kHz.

But eSDHC controllers have a non-standard SD clock management, so we can
divide clock by 256 * 16, not just 256.

This patch introduces get_min_clock() callback for sdhci core and
implements it for sdhci-of driver, and thus fixes the issue.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/mmc/host/sdhci-of.c | 8 ++++++++
 drivers/mmc/host/sdhci.c    | 5 ++++-
 drivers/mmc/host/sdhci.h    | 1 +
 3 files changed, 13 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-of.c b/drivers/mmc/host/sdhci-of.c
index d79fa55c3b8..908844327db 100644
--- a/drivers/mmc/host/sdhci-of.c
+++ b/drivers/mmc/host/sdhci-of.c
@@ -158,6 +158,13 @@ static unsigned int esdhc_get_max_clock(struct sdhci_host *host)
 	return of_host->clock;
 }
 
+static unsigned int esdhc_get_min_clock(struct sdhci_host *host)
+{
+	struct sdhci_of_host *of_host = sdhci_priv(host);
+
+	return of_host->clock / 256 / 16;
+}
+
 static unsigned int esdhc_get_timeout_clock(struct sdhci_host *host)
 {
 	struct sdhci_of_host *of_host = sdhci_priv(host);
@@ -184,6 +191,7 @@ static struct sdhci_of_data sdhci_esdhc = {
 		.set_clock = esdhc_set_clock,
 		.enable_dma = esdhc_enable_dma,
 		.get_max_clock = esdhc_get_max_clock,
+		.get_min_clock = esdhc_get_min_clock,
 		.get_timeout_clock = esdhc_get_timeout_clock,
 	},
 };
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 6779b4ecab1..62041c7e924 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -1766,7 +1766,10 @@ int sdhci_add_host(struct sdhci_host *host)
 	 * Set host parameters.
 	 */
 	mmc->ops = &sdhci_ops;
-	mmc->f_min = host->max_clk / 256;
+	if (host->ops->get_min_clock)
+		mmc->f_min = host->ops->get_min_clock(host);
+	else
+		mmc->f_min = host->max_clk / 256;
 	mmc->f_max = host->max_clk;
 	mmc->caps = MMC_CAP_SDIO_IRQ;
 
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index 831ddf7dcb4..c77e9ff3022 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -302,6 +302,7 @@ struct sdhci_ops {
 
 	int		(*enable_dma)(struct sdhci_host *host);
 	unsigned int	(*get_max_clock)(struct sdhci_host *host);
+	unsigned int	(*get_min_clock)(struct sdhci_host *host);
 	unsigned int	(*get_timeout_clock)(struct sdhci_host *host);
 };
 
-- 
GitLab


From 534acc057b5a08ec33fa57cdd2f5a09ef124e7f2 Mon Sep 17 00:00:00 2001
From: Dave Hansen <dave@linux.vnet.ibm.com>
Date: Wed, 29 Jul 2009 15:04:18 -0700
Subject: [PATCH 0271/1153] lib: flexible array implementation

Once a structure goes over PAGE_SIZE*2, we see occasional allocation
failures.  Some people have chosen to switch over to things like vmalloc()
that will let them keep array-like access to such a large structures.
But, vmalloc() has plenty of downsides.

Here's an alternative.  I think it's what Andrew was suggesting here:

	http://lkml.org/lkml/2009/7/2/518

I call it a flexible array.  It does all of its work in PAGE_SIZE bits, so
never does an order>0 allocation.  The base level has
PAGE_SIZE-2*sizeof(int) bytes of storage for pointers to the second level.
 So, with a 32-bit arch, you get about 4MB (4183112 bytes) of total
storage when the objects pack nicely into a page.  It is half that on
64-bit because the pointers are twice the size.  There's a table detailing
this in the code.

There are kerneldocs for the functions, but here's an
overview:

flex_array_alloc() - dynamically allocate a base structure
flex_array_free() - free the array and all of the
		    second-level pages
flex_array_free_parts() - free the second-level pages, but
			  not the base (for static bases)
flex_array_put() - copy into the array at the given index
flex_array_get() - copy out of the array at the given index
flex_array_prealloc() - preallocate the second-level pages
			between the given indexes to
			guarantee no allocs will occur at
			put() time.

We could also potentially just pass the "element_size" into each of the
API functions instead of storing it internally.  That would get us one
more base pointer on 32-bit.

I've been testing this by running it in userspace.  The header and patch
that I've been using are here, as well as the little script I'm using to
generate the size table which goes in the kerneldocs.

	http://sr71.net/~dave/linux/flexarray/

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/flex_array.h |  47 +++++++
 lib/Makefile               |   2 +-
 lib/flex_array.c           | 269 +++++++++++++++++++++++++++++++++++++
 3 files changed, 317 insertions(+), 1 deletion(-)
 create mode 100644 include/linux/flex_array.h
 create mode 100644 lib/flex_array.c

diff --git a/include/linux/flex_array.h b/include/linux/flex_array.h
new file mode 100644
index 00000000000..23c1ec79a31
--- /dev/null
+++ b/include/linux/flex_array.h
@@ -0,0 +1,47 @@
+#ifndef _FLEX_ARRAY_H
+#define _FLEX_ARRAY_H
+
+#include <linux/types.h>
+#include <asm/page.h>
+
+#define FLEX_ARRAY_PART_SIZE PAGE_SIZE
+#define FLEX_ARRAY_BASE_SIZE PAGE_SIZE
+
+struct flex_array_part;
+
+/*
+ * This is meant to replace cases where an array-like
+ * structure has gotten too big to fit into kmalloc()
+ * and the developer is getting tempted to use
+ * vmalloc().
+ */
+
+struct flex_array {
+	union {
+		struct {
+			int element_size;
+			int total_nr_elements;
+			struct flex_array_part *parts[0];
+		};
+		/*
+		 * This little trick makes sure that
+		 * sizeof(flex_array) == PAGE_SIZE
+		 */
+		char padding[FLEX_ARRAY_BASE_SIZE];
+	};
+};
+
+#define FLEX_ARRAY_INIT(size, total) { { {\
+	.element_size = (size),		\
+	.total_nr_elements = (total),	\
+} } }
+
+struct flex_array *flex_array_alloc(int element_size, int total, gfp_t flags);
+int flex_array_prealloc(struct flex_array *fa, int start, int end, gfp_t flags);
+void flex_array_free(struct flex_array *fa);
+void flex_array_free_parts(struct flex_array *fa);
+int flex_array_put(struct flex_array *fa, int element_nr, void *src,
+		gfp_t flags);
+void *flex_array_get(struct flex_array *fa, int element_nr);
+
+#endif /* _FLEX_ARRAY_H */
diff --git a/lib/Makefile b/lib/Makefile
index b6d1857bbf0..2e78277eff9 100644
--- a/lib/Makefile
+++ b/lib/Makefile
@@ -12,7 +12,7 @@ lib-y := ctype.o string.o vsprintf.o cmdline.o \
 	 idr.o int_sqrt.o extable.o prio_tree.o \
 	 sha1.o irq_regs.o reciprocal_div.o argv_split.o \
 	 proportions.o prio_heap.o ratelimit.o show_mem.o \
-	 is_single_threaded.o plist.o decompress.o
+	 is_single_threaded.o plist.o decompress.o flex_array.o
 
 lib-$(CONFIG_MMU) += ioremap.o
 lib-$(CONFIG_SMP) += cpumask.o
diff --git a/lib/flex_array.c b/lib/flex_array.c
new file mode 100644
index 00000000000..0e7894ce888
--- /dev/null
+++ b/lib/flex_array.c
@@ -0,0 +1,269 @@
+/*
+ * Flexible array managed in PAGE_SIZE parts
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ * Copyright IBM Corporation, 2009
+ *
+ * Author: Dave Hansen <dave@linux.vnet.ibm.com>
+ */
+
+#include <linux/flex_array.h>
+#include <linux/slab.h>
+#include <linux/stddef.h>
+
+struct flex_array_part {
+	char elements[FLEX_ARRAY_PART_SIZE];
+};
+
+static inline int __elements_per_part(int element_size)
+{
+	return FLEX_ARRAY_PART_SIZE / element_size;
+}
+
+static inline int bytes_left_in_base(void)
+{
+	int element_offset = offsetof(struct flex_array, parts);
+	int bytes_left = FLEX_ARRAY_BASE_SIZE - element_offset;
+	return bytes_left;
+}
+
+static inline int nr_base_part_ptrs(void)
+{
+	return bytes_left_in_base() / sizeof(struct flex_array_part *);
+}
+
+/*
+ * If a user requests an allocation which is small
+ * enough, we may simply use the space in the
+ * flex_array->parts[] array to store the user
+ * data.
+ */
+static inline int elements_fit_in_base(struct flex_array *fa)
+{
+	int data_size = fa->element_size * fa->total_nr_elements;
+	if (data_size <= bytes_left_in_base())
+		return 1;
+	return 0;
+}
+
+/**
+ * flex_array_alloc - allocate a new flexible array
+ * @element_size:	the size of individual elements in the array
+ * @total:		total number of elements that this should hold
+ *
+ * Note: all locking must be provided by the caller.
+ *
+ * @total is used to size internal structures.  If the user ever
+ * accesses any array indexes >=@total, it will produce errors.
+ *
+ * The maximum number of elements is defined as: the number of
+ * elements that can be stored in a page times the number of
+ * page pointers that we can fit in the base structure or (using
+ * integer math):
+ *
+ * 	(PAGE_SIZE/element_size) * (PAGE_SIZE-8)/sizeof(void *)
+ *
+ * Here's a table showing example capacities.  Note that the maximum
+ * index that the get/put() functions is just nr_objects-1.   This
+ * basically means that you get 4MB of storage on 32-bit and 2MB on
+ * 64-bit.
+ *
+ *
+ * Element size | Objects | Objects |
+ * PAGE_SIZE=4k |  32-bit |  64-bit |
+ * ---------------------------------|
+ *      1 bytes | 4186112 | 2093056 |
+ *      2 bytes | 2093056 | 1046528 |
+ *      3 bytes | 1395030 |  697515 |
+ *      4 bytes | 1046528 |  523264 |
+ *     32 bytes |  130816 |   65408 |
+ *     33 bytes |  126728 |   63364 |
+ *   2048 bytes |    2044 |    1022 |
+ *   2049 bytes |    1022 |     511 |
+ *       void * | 1046528 |  261632 |
+ *
+ * Since 64-bit pointers are twice the size, we lose half the
+ * capacity in the base structure.  Also note that no effort is made
+ * to efficiently pack objects across page boundaries.
+ */
+struct flex_array *flex_array_alloc(int element_size, int total, gfp_t flags)
+{
+	struct flex_array *ret;
+	int max_size = nr_base_part_ptrs() * __elements_per_part(element_size);
+
+	/* max_size will end up 0 if element_size > PAGE_SIZE */
+	if (total > max_size)
+		return NULL;
+	ret = kzalloc(sizeof(struct flex_array), flags);
+	if (!ret)
+		return NULL;
+	ret->element_size = element_size;
+	ret->total_nr_elements = total;
+	return ret;
+}
+
+static int fa_element_to_part_nr(struct flex_array *fa, int element_nr)
+{
+	return element_nr / __elements_per_part(fa->element_size);
+}
+
+/**
+ * flex_array_free_parts - just free the second-level pages
+ * @src:	address of data to copy into the array
+ * @element_nr:	index of the position in which to insert
+ * 		the new element.
+ *
+ * This is to be used in cases where the base 'struct flex_array'
+ * has been statically allocated and should not be free.
+ */
+void flex_array_free_parts(struct flex_array *fa)
+{
+	int part_nr;
+	int max_part = nr_base_part_ptrs();
+
+	if (elements_fit_in_base(fa))
+		return;
+	for (part_nr = 0; part_nr < max_part; part_nr++)
+		kfree(fa->parts[part_nr]);
+}
+
+void flex_array_free(struct flex_array *fa)
+{
+	flex_array_free_parts(fa);
+	kfree(fa);
+}
+
+static int fa_index_inside_part(struct flex_array *fa, int element_nr)
+{
+	return element_nr % __elements_per_part(fa->element_size);
+}
+
+static int index_inside_part(struct flex_array *fa, int element_nr)
+{
+	int part_offset = fa_index_inside_part(fa, element_nr);
+	return part_offset * fa->element_size;
+}
+
+static struct flex_array_part *
+__fa_get_part(struct flex_array *fa, int part_nr, gfp_t flags)
+{
+	struct flex_array_part *part = fa->parts[part_nr];
+	if (!part) {
+		/*
+		 * This leaves the part pages uninitialized
+		 * and with potentially random data, just
+		 * as if the user had kmalloc()'d the whole.
+		 * __GFP_ZERO can be used to zero it.
+		 */
+		part = kmalloc(FLEX_ARRAY_PART_SIZE, flags);
+		if (!part)
+			return NULL;
+		fa->parts[part_nr] = part;
+	}
+	return part;
+}
+
+/**
+ * flex_array_put - copy data into the array at @element_nr
+ * @src:	address of data to copy into the array
+ * @element_nr:	index of the position in which to insert
+ * 		the new element.
+ *
+ * Note that this *copies* the contents of @src into
+ * the array.  If you are trying to store an array of
+ * pointers, make sure to pass in &ptr instead of ptr.
+ *
+ * Locking must be provided by the caller.
+ */
+int flex_array_put(struct flex_array *fa, int element_nr, void *src, gfp_t flags)
+{
+	int part_nr = fa_element_to_part_nr(fa, element_nr);
+	struct flex_array_part *part;
+	void *dst;
+
+	if (element_nr >= fa->total_nr_elements)
+		return -ENOSPC;
+	if (elements_fit_in_base(fa))
+		part = (struct flex_array_part *)&fa->parts[0];
+	else
+		part = __fa_get_part(fa, part_nr, flags);
+	if (!part)
+		return -ENOMEM;
+	dst = &part->elements[index_inside_part(fa, element_nr)];
+	memcpy(dst, src, fa->element_size);
+	return 0;
+}
+
+/**
+ * flex_array_prealloc - guarantee that array space exists
+ * @start:	index of first array element for which space is allocated
+ * @end:	index of last (inclusive) element for which space is allocated
+ *
+ * This will guarantee that no future calls to flex_array_put()
+ * will allocate memory.  It can be used if you are expecting to
+ * be holding a lock or in some atomic context while writing
+ * data into the array.
+ *
+ * Locking must be provided by the caller.
+ */
+int flex_array_prealloc(struct flex_array *fa, int start, int end, gfp_t flags)
+{
+	int start_part;
+	int end_part;
+	int part_nr;
+	struct flex_array_part *part;
+
+	if (start >= fa->total_nr_elements || end >= fa->total_nr_elements)
+		return -ENOSPC;
+	if (elements_fit_in_base(fa))
+		return 0;
+	start_part = fa_element_to_part_nr(fa, start);
+	end_part = fa_element_to_part_nr(fa, end);
+	for (part_nr = start_part; part_nr <= end_part; part_nr++) {
+		part = __fa_get_part(fa, part_nr, flags);
+		if (!part)
+			return -ENOMEM;
+	}
+	return 0;
+}
+
+/**
+ * flex_array_get - pull data back out of the array
+ * @element_nr:	index of the element to fetch from the array
+ *
+ * Returns a pointer to the data at index @element_nr.  Note
+ * that this is a copy of the data that was passed in.  If you
+ * are using this to store pointers, you'll get back &ptr.
+ *
+ * Locking must be provided by the caller.
+ */
+void *flex_array_get(struct flex_array *fa, int element_nr)
+{
+	int part_nr = fa_element_to_part_nr(fa, element_nr);
+	struct flex_array_part *part;
+	int index;
+
+	if (element_nr >= fa->total_nr_elements)
+		return NULL;
+	if (!fa->parts[part_nr])
+		return NULL;
+	if (elements_fit_in_base(fa))
+		part = (struct flex_array_part *)&fa->parts[0];
+	else
+		part = fa->parts[part_nr];
+	index = index_inside_part(fa, element_nr);
+	return &part->elements[index_inside_part(fa, element_nr)];
+}
-- 
GitLab


From 8da14b5fc32368f582df09fe9c0bec2507868583 Mon Sep 17 00:00:00 2001
From: Albin Tonnerre <albin.tonnerre@gmail.com>
Date: Wed, 29 Jul 2009 15:04:18 -0700
Subject: [PATCH 0272/1153] drivers/serial/atmel_serial.c: fix compile when
 CONFIG_SERIAL_ATMEL=Y and CONFIG_SERIAL_ATMEL_CONSOLE=N

When SERIAL_ATMEL_CONSOLE is disabled, ATMEL_CONSOLE_DEVICE is set to
NULL, and trying to access ATMEL_CONSOLE_DEVICE->flags in
atmel_serial_probe makes the compile fail.  This fixes the issue by only
accessing it if CONFIG_SERIAL_ATMEL_CONSOLE is defined

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/serial/atmel_serial.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c
index 338b15c0a54..607d43a3104 100644
--- a/drivers/serial/atmel_serial.c
+++ b/drivers/serial/atmel_serial.c
@@ -1551,6 +1551,7 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_add_port;
 
+#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
 	if (atmel_is_console_port(&port->uart)
 			&& ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) {
 		/*
@@ -1559,6 +1560,7 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev)
 		 */
 		clk_disable(port->clk);
 	}
+#endif
 
 	device_init_wakeup(&pdev->dev, 1);
 	platform_set_drvdata(pdev, port);
-- 
GitLab


From 812ed032cdc8138b7546eecc996879756b92d801 Mon Sep 17 00:00:00 2001
From: Jiri Slaby <jirislaby@gmail.com>
Date: Wed, 29 Jul 2009 15:04:19 -0700
Subject: [PATCH 0273/1153] uio: mark uio.h functions __KERNEL__ only

To avoid userspace build failures such as:

.../linux/uio.h:37: error: expected `=', `,', `;', `asm' or `__attribute__' before `iov_length'
.../linux/uio.h:47: error: expected declaration specifiers or `...' before `size_t'

move uio functions inside a __KERNEL__ block.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/uio.h | 17 ++++++++---------
 1 file changed, 8 insertions(+), 9 deletions(-)

diff --git a/include/linux/uio.h b/include/linux/uio.h
index b7fe13883bd..98c114323a8 100644
--- a/include/linux/uio.h
+++ b/include/linux/uio.h
@@ -19,15 +19,6 @@ struct iovec
 	__kernel_size_t iov_len; /* Must be size_t (1003.1g) */
 };
 
-#ifdef __KERNEL__
-
-struct kvec {
-	void *iov_base; /* and that should *never* hold a userland pointer */
-	size_t iov_len;
-};
-
-#endif
-
 /*
  *	UIO_MAXIOV shall be at least 16 1003.1g (5.4.1.1)
  */
@@ -35,6 +26,13 @@ struct kvec {
 #define UIO_FASTIOV	8
 #define UIO_MAXIOV	1024
 
+#ifdef __KERNEL__
+
+struct kvec {
+	void *iov_base; /* and that should *never* hold a userland pointer */
+	size_t iov_len;
+};
+
 /*
  * Total number of bytes covered by an iovec.
  *
@@ -53,5 +51,6 @@ static inline size_t iov_length(const struct iovec *iov, unsigned long nr_segs)
 }
 
 unsigned long iov_shorten(struct iovec *iov, unsigned long nr_segs, size_t to);
+#endif
 
 #endif
-- 
GitLab


From 56d44f05177e69b757a01987827db8ef79fb759c Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:20 -0700
Subject: [PATCH 0274/1153] MAINTAINERS: IA64 - pair P:/M: entries properly

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index ebc269152fa..5fe36a33ca6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2858,8 +2858,8 @@ S:	Maintained
 
 IA64 (Itanium) PLATFORM
 P:	Tony Luck
-P:	Fenghua Yu
 M:	tony.luck@intel.com
+P:	Fenghua Yu
 M:	fenghua.yu@intel.com
 L:	linux-ia64@vger.kernel.org
 W:	http://www.ia64-linux.org/
-- 
GitLab


From 30e10993512c94daf0ab5cb4b512979aa1c85daf Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:21 -0700
Subject: [PATCH 0275/1153] MAINTAINERS: Remove ivtv-user lists, add CX18 url

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 5fe36a33ca6..104850879f2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1728,10 +1728,10 @@ M:	hverkuil@xs4all.nl
 P:	Andy Walls
 M:	awalls@radix.net
 L:	ivtv-devel@ivtvdriver.org
-L:	ivtv-users@ivtvdriver.org
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 W:	http://linuxtv.org
+W:	http://www.ivtvdriver.org/index.php/Cx18
 S:	Maintained
 F:	Documentation/video4linux/cx18.txt
 F:	drivers/media/video/cx18/
@@ -3283,7 +3283,6 @@ IVTV VIDEO4LINUX DRIVER
 P:	Hans Verkuil
 M:	hverkuil@xs4all.nl
 L:	ivtv-devel@ivtvdriver.org
-L:	ivtv-users@ivtvdriver.org
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 W:	http://www.ivtvdriver.org
-- 
GitLab


From 4cbfbe256dc0b0491351bc5bea89f229cfae2284 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:21 -0700
Subject: [PATCH 0276/1153] MAINTAINERS: QLGE 10Gb ETHERNET - pair P:/M:
 entries properly

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 104850879f2..a6d6420d5b1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4821,8 +4821,8 @@ F:	drivers/net/qla3xxx.*
 
 QLOGIC QLGE 10Gb ETHERNET DRIVER
 P:	Ron Mercer
-M:	linux-driver@qlogic.com
 M:	ron.mercer@qlogic.com
+M:	linux-driver@qlogic.com
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/qlge/
-- 
GitLab


From 4fc26e36acce714ca26b576e3e6862887fa130d3 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:22 -0700
Subject: [PATCH 0277/1153] MAINTAINERS: Use tabs in ACER ASPIRE ONE

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index a6d6420d5b1..6504fb916a1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -231,11 +231,11 @@ S:	Maintained
 F:	drivers/net/acenic*
 
 ACER ASPIRE ONE TEMPERATURE AND FAN DRIVER
-P: Peter Feuerer
-M: peter@piie.net
-W: http://piie.net/?section=acerhdf
-S: Maintained
-F: drivers/platform/x86/acerhdf.c
+P:	Peter Feuerer
+M:	peter@piie.net
+W:	http://piie.net/?section=acerhdf
+S:	Maintained
+F:	drivers/platform/x86/acerhdf.c
 
 ACER WMI LAPTOP EXTRAS
 P:	Carlos Corbacho
-- 
GitLab


From 5daa2963f8bd51c161d5b244e439e0c9fdec358b Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:23 -0700
Subject: [PATCH 0278/1153] MAINTAINERS: Remove L: linux-kernel@vger.kernel.org

from sections that should not have them.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 6504fb916a1..7d10f06d088 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2204,7 +2204,6 @@ F:	drivers/scsi/lpfc/
 ENE CB710 FLASH CARD READER DRIVER
 P:	Michał Mirosław
 M:	mirq-linux@rere.qmqm.pl
-L:	linux-kernel@vger.kernel.org
 S:	Maintained
 F:	drivers/misc/cb710/
 F:	drivers/mmc/host/cb710-mmc.*
@@ -3480,13 +3479,11 @@ P:	Vegard Nossum
 M:	vegardno@ifi.uio.no
 P	Pekka Enberg
 M:	penberg@cs.helsinki.fi
-L:	linux-kernel@vger.kernel.org
 S:	Maintained
 
 KMEMLEAK
 P:	Catalin Marinas
 M:	catalin.marinas@arm.com
-L:	linux-kernel@vger.kernel.org
 S:	Maintained
 F:	Documentation/kmemleak.txt
 F:	include/linux/kmemleak.h
@@ -4306,7 +4303,6 @@ F:	drivers/video/omap/
 OMAP MMC SUPPORT
 P:	Jarkko Lavinen
 M:	jarkko.lavinen@nokia.com
-L:	linux-kernel@vger.kernel.org
 L:	linux-omap@vger.kernel.org
 S:	Maintained
 F:	drivers/mmc/host/*omap*
@@ -4588,7 +4584,6 @@ P:	Paul Mackerras
 M:	paulus@samba.org
 P:	Ingo Molnar
 M:	mingo@elte.hu
-L:	linux-kernel@vger.kernel.org
 S:	Supported
 
 PERSONALITY HANDLING
-- 
GitLab


From eb51b0349df8efccc37fc06aa25aecbd4d39551b Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:23 -0700
Subject: [PATCH 0279/1153] MAINTAINERS: Move ARPD to CREDITS

Jonathan Layes is hard to find.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 CREDITS     | 3 +++
 MAINTAINERS | 6 ------
 2 files changed, 3 insertions(+), 6 deletions(-)

diff --git a/CREDITS b/CREDITS
index e76d300e9fe..44c13d19e7e 100644
--- a/CREDITS
+++ b/CREDITS
@@ -2006,6 +2006,9 @@ E: paul@laufernet.com
 D: Soundblaster driver fixes, ISAPnP quirk
 S: California, USA
 
+N: Jonathan Layes
+D: ARPD support
+
 N: Tom Lees
 E: tom@lpsg.demon.co.uk
 W: http://www.lpsg.demon.co.uk/
diff --git a/MAINTAINERS b/MAINTAINERS
index 7d10f06d088..b42f1b11fa0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -951,12 +951,6 @@ W:	http://www.arm.linux.org.uk/
 S:	Maintained
 F:	arch/arm/vfp/
 
-ARPD SUPPORT
-P:	Jonathan Layes
-L:	netdev@vger.kernel.org
-S:	Maintained
-F:	net/ipv4/arp.c
-
 ASUS ACPI EXTRAS DRIVER
 P:	Corentin Chary
 M:	corentincj@iksaif.net
-- 
GitLab


From 24725d1ecf26ba05d74c1cc3ae7467b61a900421 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:24 -0700
Subject: [PATCH 0280/1153] MAINTAINERS: Update KERNEL JANITORS

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index b42f1b11fa0..7a22e706852 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3373,10 +3373,9 @@ F:	Makefile
 F:	scripts/Makefile.*
 
 KERNEL JANITORS
-P:	Several
 L:	kernel-janitors@vger.kernel.org
 W:	http://www.kerneljanitors.org/
-S:	Maintained
+S:	Odd fixes
 
 KERNEL NFSD, SUNRPC, AND LOCKD SERVERS
 P:	J. Bruce Fields
-- 
GitLab


From cabaaf415cc9820cfbf2bc86308b94b78e31fe3e Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:24 -0700
Subject: [PATCH 0281/1153] MAINTAINERS: Add PPS patterns

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 7a22e706852..b1859597fa2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4667,6 +4667,9 @@ M:	giometti@enneenne.com
 W:	http://wiki.enneenne.com/index.php/LinuxPPS_support
 L:	linuxpps@ml.enneenne.com (subscribers-only)
 S:	Maintained
+F:	Documentation/pps/
+F:	drivers/pps/
+F:	include/linux/pps*.h
 
 PREEMPTIBLE KERNEL
 P:	Robert Love
-- 
GitLab


From a72f8024f4c9b06ff35d0bf6df479ea7fae4e2f8 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:25 -0700
Subject: [PATCH 0282/1153] MAINTAINERS: USB Serial Digi Acceleport: use
 separate P: for Al Borchers

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index b1859597fa2..b8d6bd35563 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -6105,8 +6105,9 @@ S:	Maintained
 F:	drivers/usb/serial/cyberjack.c
 
 USB SERIAL DIGI ACCELEPORT DRIVER
-P:	Peter Berger and Al Borchers
+P:	Peter Berger
 M:	pberger@brimson.com
+P:	Al Borchers
 M:	alborchers@steinerpoint.com
 L:	linux-usb@vger.kernel.org
 S:	Maintained
-- 
GitLab


From 5bee73ff71e17f5a807376e29653998755211ceb Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:25 -0700
Subject: [PATCH 0283/1153] MAINTAINERS: INPUT: Add Dmitry's name to his email
 address

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index b8d6bd35563..6ef63194996 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2979,6 +2979,7 @@ F:	include/linux/inotify.h
 INPUT (KEYBOARD, MOUSE, JOYSTICK, TOUCHSCREEN) DRIVERS
 P:	Dmitry Torokhov
 M:	dmitry.torokhov@gmail.com
+P:	Dmitry Torokhov
 M:	dtor@mail.ru
 L:	linux-input@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input.git
-- 
GitLab


From 9ae9a7f119a8def8e68d7f5ab0d96b3aba80accb Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:26 -0700
Subject: [PATCH 0284/1153] MAINTAINERS: Remove CS461x sound card section

Thomas Woller's email address bounces
Nils Faerber isn't active

Added Thomas Woller to CREDITS, Nils already has an entry

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 CREDITS     | 3 +++
 MAINTAINERS | 9 ---------
 2 files changed, 3 insertions(+), 9 deletions(-)

diff --git a/CREDITS b/CREDITS
index 44c13d19e7e..1a41bf4addd 100644
--- a/CREDITS
+++ b/CREDITS
@@ -3805,6 +3805,9 @@ S: van Bronckhorststraat 12
 S: 2612 XV Delft
 S: The Netherlands
 
+N: Thomas Woller
+D: CS461x Cirrus Logic sound driver
+
 N: David Woodhouse
 E: dwmw2@infradead.org
 D: JFFS2 file system, Memory Technology Device subsystem,
diff --git a/MAINTAINERS b/MAINTAINERS
index 6ef63194996..1b02be36d96 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1508,15 +1508,6 @@ L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 S:	Supported
 F:	sound/soc/codecs/cs4270*
 
-CIRRUS LOGIC CS4280/CS461x SOUNDDRIVER
-P:	Cirrus Logic Corporation (kernel 2.2 driver)
-M:	Cirrus Logic Corporation, Thomas Woller <twoller@crystal.cirrus.com>
-P:	Nils Faerber (port to kernel 2.4)
-M:	Nils Faerber <nils@kernelconcepts.de>
-S:	Maintained
-F:	Documentation/input/cs461x.txt
-F:	sound/pci/cs46xx/
-
 CLK API
 P:	Russell King
 M:	linux@arm.linux.org.uk
-- 
GitLab


From edf4b0a980bf481bbcef0977e2c7369f13f3428f Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:26 -0700
Subject: [PATCH 0285/1153] MAINTAINERS: QLOGIC QLA2XXX - add Andrew Vasquez
 email address

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 1b02be36d96..8ca15f6a460 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4788,6 +4788,7 @@ S:	Maintained
 
 QLOGIC QLA2XXX FC-SCSI DRIVER
 P:	Andrew Vasquez
+M:	andrew.vasquez@qlogic.com
 M:	linux-driver@qlogic.com
 L:	linux-scsi@vger.kernel.org
 S:	Supported
-- 
GitLab


From 2bd1944899354b6f1328fe84886fa8f4d5918aef Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:27 -0700
Subject: [PATCH 0286/1153] MAINTAINERS: QLOGIC QLA3XXX - Add Ron Mercer email
 address

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 8ca15f6a460..4daf259782e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4797,6 +4797,7 @@ F:	drivers/scsi/qla2xxx/
 
 QLOGIC QLA3XXX NETWORK DRIVER
 P:	Ron Mercer
+M:	ron.mercer@qlogic.com
 M:	linux-driver@qlogic.com
 L:	netdev@vger.kernel.org
 S:	Supported
-- 
GitLab


From 82c4dfc76200055bd2ae600a08404c10df5f4ff6 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:27 -0700
Subject: [PATCH 0287/1153] MAINTAINERS: Scott Murray is no longer with
 SomaNetworks

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 9 +++------
 1 file changed, 3 insertions(+), 6 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 4daf259782e..e4e3471cd0e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1546,26 +1546,23 @@ F:	fs/cifs/
 
 COMPACTPCI HOTPLUG CORE
 P:	Scott Murray
-M:	scottm@somanetworks.com
 M:	scott@spiteful.org
 L:	linux-pci@vger.kernel.org
-S:	Supported
+S:	Maintained
 F:	drivers/pci/hotplug/cpci_hotplug*
 
 COMPACTPCI HOTPLUG ZIATECH ZT5550 DRIVER
 P:	Scott Murray
-M:	scottm@somanetworks.com
 M:	scott@spiteful.org
 L:	linux-pci@vger.kernel.org
-S:	Supported
+S:	Maintained
 F:	drivers/pci/hotplug/cpcihp_zt5550.*
 
 COMPACTPCI HOTPLUG GENERIC DRIVER
 P:	Scott Murray
-M:	scottm@somanetworks.com
 M:	scott@spiteful.org
 L:	linux-pci@vger.kernel.org
-S:	Supported
+S:	Maintained
 F:	drivers/pci/hotplug/cpcihp_generic.c
 
 COMPAL LAPTOP SUPPORT
-- 
GitLab


From 870020f93af2323a81f179091a0780dc1d5b916b Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:28 -0700
Subject: [PATCH 0288/1153] scripts/get_maintainer.pl: Add -f directory use

Don't require a specific file in a directory to be tested.

Also Arnd Bergmann pointed out that the MAINTAINERS pattern requirement
that directory patterns have a trailing slash was unnecessary and was
likely to be error prone.  Removed that requirement.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 scripts/get_maintainer.pl | 23 +++++++++++++++++++----
 1 file changed, 19 insertions(+), 4 deletions(-)

diff --git a/scripts/get_maintainer.pl b/scripts/get_maintainer.pl
index 3e733146cd5..7fc09fc91e8 100755
--- a/scripts/get_maintainer.pl
+++ b/scripts/get_maintainer.pl
@@ -13,7 +13,7 @@
 use strict;
 
 my $P = $0;
-my $V = '0.16';
+my $V = '0.17';
 
 use Getopt::Long qw(:config no_auto_abbrev);
 
@@ -132,6 +132,10 @@ while (<MAINT>) {
 	    $value =~ s@\.@\\\.@g;       ##Convert . to \.
 	    $value =~ s/\*/\.\*/g;       ##Convert * to .*
 	    $value =~ s/\?/\./g;         ##Convert ? to .
+	    ##if pattern is a directory and it lacks a trailing slash, add one
+	    if ((-d $value)) {
+		$value =~ s@([^/])$@$1/@;
+	    }
 	}
 	push(@typevalue, "$type:$value");
     } elsif (!/^(\s)*$/) {
@@ -146,8 +150,10 @@ close(MAINT);
 my @files = ();
 
 foreach my $file (@ARGV) {
-    next if ((-d $file));
-    if (!(-f $file)) {
+    ##if $file is a directory and it lacks a trailing slash, add one
+    if ((-d $file)) {
+	$file =~ s@([^/])$@$1/@;
+    } elsif (!(-f $file)) {
 	die "$P: file '${file}' not found\n";
     }
     if ($from_filename) {
@@ -292,7 +298,7 @@ sub file_match_pattern {
 sub usage {
     print <<EOT;
 usage: $P [options] patchfile
-       $P [options] -f file
+       $P [options] -f file|directory
 version: $V
 
 MAINTAINER field selection options:
@@ -322,6 +328,15 @@ Other options:
   --version => show version
   --help => show this help information
 
+Notes:
+  Using "-f directory" may give unexpected results:
+
+  Used with "--git", git signators for _all_ files in and below
+     directory are examined as git recurses directories.
+     Any specified X: (exclude) pattern matches are _not_ ignored.
+  Used with "--nogit", directory is used as a pattern match,
+     no individual file within the directory or subdirectory
+     is matched.
 EOT
 }
 
-- 
GitLab


From afa81ee13033de791c41c1d9333853504653939b Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:28 -0700
Subject: [PATCH 0289/1153] get_maintainer.pl: Add git-min-percent option

Allow an option to control the minimum percentage of sign-offs required
before being considered a maintainer.

git-min-percent has a default value of 5

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 scripts/get_maintainer.pl | 19 ++++++++++++++++---
 1 file changed, 16 insertions(+), 3 deletions(-)

diff --git a/scripts/get_maintainer.pl b/scripts/get_maintainer.pl
index 7fc09fc91e8..61ef27564ed 100755
--- a/scripts/get_maintainer.pl
+++ b/scripts/get_maintainer.pl
@@ -27,6 +27,7 @@ my $email_git = 1;
 my $email_git_penguin_chiefs = 0;
 my $email_git_min_signatures = 1;
 my $email_git_max_maintainers = 5;
+my $email_git_min_percent = 5;
 my $email_git_since = "1-year-ago";
 my $output_multiline = 1;
 my $output_separator = ", ";
@@ -65,6 +66,7 @@ if (!GetOptions(
 		'git-chief-penguins!' => \$email_git_penguin_chiefs,
 		'git-min-signatures=i' => \$email_git_min_signatures,
 		'git-max-maintainers=i' => \$email_git_max_maintainers,
+		'git-min-percent=i' => \$email_git_min_percent,
 		'git-since=s' => \$email_git_since,
 		'm!' => \$email_maintainer,
 		'n!' => \$email_usename,
@@ -307,6 +309,7 @@ MAINTAINER field selection options:
     --git-chief-penguins => include ${penguin_chiefs}
     --git-min-signatures => number of signatures required (default: 1)
     --git-max-maintainers => maximum maintainers to add (default: 5)
+    --git-min-percent => minimum percentage of commits required (default: 0)
     --git-since => git history to use (default: 1-year-ago)
     --m => include maintainer(s) if any
     --n => include name 'Full Name <addr\@domain.tld>'
@@ -497,6 +500,7 @@ sub recent_git_signoffs {
     my $output = "";
     my $count = 0;
     my @lines = ();
+    my $total_sign_offs;
 
     if (which("git") eq "") {
 	warn("$P: git not found.  Add --nogit to options?\n");
@@ -520,17 +524,26 @@ sub recent_git_signoffs {
     $output =~ s/^\s*//gm;
 
     @lines = split("\n", $output);
+
+    $total_sign_offs = 0;
+    foreach my $line (@lines) {
+	if ($line =~ m/([0-9]+)\s+(.*)/) {
+	    $total_sign_offs += $1;
+	} else {
+	    die("$P: Unexpected git output: ${line}\n");
+	}
+    }
+
     foreach my $line (@lines) {
 	if ($line =~ m/([0-9]+)\s+(.*)/) {
 	    my $sign_offs = $1;
 	    $line = $2;
 	    $count++;
 	    if ($sign_offs < $email_git_min_signatures ||
-	        $count > $email_git_max_maintainers) {
+	        $count > $email_git_max_maintainers ||
+		$sign_offs * 100 / $total_sign_offs < $email_git_min_percent) {
 		last;
 	    }
-	} else {
-	    die("$P: Unexpected git output: ${line}\n");
 	}
 	if ($line =~ m/(.+)<(.+)>/) {
 	    my $git_name = $1;
-- 
GitLab


From 3d202aeb7b7b33d5a5b2040ee5af5b309782941c Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:29 -0700
Subject: [PATCH 0290/1153] get_maintainerpl-add-git-min-percent-option-fix

Allow an option to control the minimum percentage of sign-offs required
before being considered a maintainer.

git-min-percent has a default value of 5

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 scripts/get_maintainer.pl | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/scripts/get_maintainer.pl b/scripts/get_maintainer.pl
index 61ef27564ed..278a45bd45a 100755
--- a/scripts/get_maintainer.pl
+++ b/scripts/get_maintainer.pl
@@ -309,7 +309,7 @@ MAINTAINER field selection options:
     --git-chief-penguins => include ${penguin_chiefs}
     --git-min-signatures => number of signatures required (default: 1)
     --git-max-maintainers => maximum maintainers to add (default: 5)
-    --git-min-percent => minimum percentage of commits required (default: 0)
+    --git-min-percent => minimum percentage of commits required (default: 5)
     --git-since => git history to use (default: 1-year-ago)
     --m => include maintainer(s) if any
     --n => include name 'Full Name <addr\@domain.tld>'
-- 
GitLab


From 8b58be884a9fd650abb7f7adf3f885fb9cecd79d Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:30 -0700
Subject: [PATCH 0291/1153] MAINTAINERS: coalesce name and email address lines

Switch the MAINTAINERS email address format from

P:	Linus Torvalds
M:	torvalds@linux-foundation.org

to

M:	Linus Torvalds <torvalds@linux-foundation.org>

Mainly to ease the copy-n-pasting of maitnainer addresses into email clients.

The script to perform this operation:

#! /bin/sh
#
# Change MAINTAINERS from
#	P: name
#	M: address
# to:
#	M: name <address>
#
# Integrate P: and M: lines
#
perl -i -e 'local $/; while(<>) { s@P:	([^\n]+)\nM:	([^\n]+)\n@M:	\1 <\2>\n@g; print; }' MAINTAINERS
#
# Quote names with periods, commas and parentheses
#
sed -r -i -e "s/^M:	(.+)([\.,'\(])(.*) </M:	\"\1\2\3\" </g" MAINTAINERS

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 2721 +++++++++++++++++----------------------------------
 1 file changed, 907 insertions(+), 1814 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index e4e3471cd0e..a013e963fc0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -104,67 +104,58 @@ X: Files and directories that are NOT maintained, same rules as F:
    matches all files in and below net excluding net/ipv6/
 
 3C505 NETWORK DRIVER
-P:	Philip Blundell
-M:	philb@gnu.org
+M:	Philip Blundell <philb@gnu.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/3c505*
 
 3C59X NETWORK DRIVER
-P:	Steffen Klassert
-M:	klassert@mathematik.tu-chemnitz.de
+M:	Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	Documentation/networking/vortex.txt
 F:	drivers/net/3c59x.c
 
 3CR990 NETWORK DRIVER
-P:	David Dillow
-M:	dave@thedillows.org
+M:	David Dillow <dave@thedillows.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/typhoon*
 
 3W-9XXX SATA-RAID CONTROLLER DRIVER
-P:	Adam Radford
-M:	linuxraid@amcc.com
+M:	Adam Radford <linuxraid@amcc.com>
 L:	linux-scsi@vger.kernel.org
 W:	http://www.amcc.com
 S:	Supported
 F:	drivers/scsi/3w-9xxx*
 
 3W-XXXX ATA-RAID CONTROLLER DRIVER
-P:	Adam Radford
-M:	linuxraid@amcc.com
+M:	Adam Radford <linuxraid@amcc.com>
 L:	linux-scsi@vger.kernel.org
 W:	http://www.amcc.com
 S:	Supported
 F:	drivers/scsi/3w-xxxx*
 
 53C700 AND 53C700-66 SCSI DRIVER
-P:	James E.J. Bottomley
-M:	James.Bottomley@HansenPartnership.com
+M:	"James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/53c700*
 
 6PACK NETWORK DRIVER FOR AX.25
-P:	Andreas Koensgen
-M:	ajk@comnets.uni-bremen.de
+M:	Andreas Koensgen <ajk@comnets.uni-bremen.de>
 L:	linux-hams@vger.kernel.org
 S:	Maintained
 F:	drivers/net/hamradio/6pack.c
 
 8169 10/100/1000 GIGABIT ETHERNET DRIVER
-P:	Francois Romieu
-M:	romieu@fr.zoreil.com
+M:	Francois Romieu <romieu@fr.zoreil.com>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/r8169.c
 
 8250/16?50 (AND CLONE UARTS) SERIAL DRIVER
-P:	Alan Cox
-M:	alan@lxorguk.ukuu.org.uk
+M:	Alan Cox <alan@lxorguk.ukuu.org.uk>
 L:	linux-serial@vger.kernel.org
 W:	http://serial.sourceforge.net
 S:	Odd Fixes
@@ -172,20 +163,16 @@ F:	drivers/serial/8250*
 F:	include/linux/serial_8250.h
 
 8390 NETWORK DRIVERS [WD80x3/SMC-ELITE, SMC-ULTRA, NE2000, 3C503, etc.]
-P:	Paul Gortmaker
-M:	p_gortmaker@yahoo.com
+M:	Paul Gortmaker <p_gortmaker@yahoo.com>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/*8390*
 F:	drivers/net/ax88796.c
 
 9P FILE SYSTEM
-P:	Eric Van Hensbergen
-M:	ericvh@gmail.com
-P:	Ron Minnich
-M:	rminnich@sandia.gov
-P:	Latchesar Ionkov
-M:	lucho@ionkov.net
+M:	Eric Van Hensbergen <ericvh@gmail.com>
+M:	Ron Minnich <rminnich@sandia.gov>
+M:	Latchesar Ionkov <lucho@ionkov.net>
 L:	v9fs-developer@lists.sourceforge.net
 W:	http://swik.net/v9fs
 T:	git git://git.kernel.org/pub/scm/linux/kernel/ericvh/v9fs.git
@@ -194,15 +181,13 @@ F:	Documentation/filesystems/9p.txt
 F:	fs/9p/
 
 A2232 SERIAL BOARD DRIVER
-P:	Enver Haase
-M:	A2232@gmx.net
+M:	Enver Haase <A2232@gmx.net>
 L:	linux-m68k@lists.linux-m68k.org
 S:	Maintained
 F:	drivers/char/ser_a2232*
 
 AACRAID SCSI RAID DRIVER
-P:	Adaptec OEM Raid Solutions
-M:	aacraid@adaptec.com
+M:	Adaptec OEM Raid Solutions <aacraid@adaptec.com>
 L:	linux-scsi@vger.kernel.org
 W:	http://www.adaptec.com/
 S:	Supported
@@ -210,44 +195,38 @@ F:	Documentation/scsi/aacraid.txt
 F:	drivers/scsi/aacraid/
 
 ABIT UGURU 1,2 HARDWARE MONITOR DRIVER
-P:	Hans de Goede
-M:	j.w.r.degoede@hhs.nl
+M:	Hans de Goede <j.w.r.degoede@hhs.nl>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	drivers/hwmon/abituguru.c
 
 ABIT UGURU 3 HARDWARE MONITOR DRIVER
-P:	Alistair John Strachan
-M:	alistair@devzero.co.uk
+M:	Alistair John Strachan <alistair@devzero.co.uk>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	drivers/hwmon/abituguru3.c
 
 ACENIC DRIVER
-P:	Jes Sorensen
-M:	jes@trained-monkey.org
+M:	Jes Sorensen <jes@trained-monkey.org>
 L:	linux-acenic@sunsite.dk
 S:	Maintained
 F:	drivers/net/acenic*
 
 ACER ASPIRE ONE TEMPERATURE AND FAN DRIVER
-P:	Peter Feuerer
-M:	peter@piie.net
+M:	Peter Feuerer <peter@piie.net>
 W:	http://piie.net/?section=acerhdf
 S:	Maintained
 F:	drivers/platform/x86/acerhdf.c
 
 ACER WMI LAPTOP EXTRAS
-P:	Carlos Corbacho
-M:	carlos@strangeworlds.co.uk
+M:	Carlos Corbacho <carlos@strangeworlds.co.uk>
 L:	aceracpi@googlegroups.com (subscribers-only)
 W:	http://code.google.com/p/aceracpi
 S:	Maintained
 F:	drivers/platform/x86/acer-wmi.c
 
 ACPI
-P:	Len Brown
-M:	lenb@kernel.org
+M:	Len Brown <lenb@kernel.org>
 L:	linux-acpi@vger.kernel.org
 W:	http://www.lesswatts.org/projects/acpi/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6.git
@@ -257,8 +236,7 @@ F:	drivers/pnp/pnpacpi/
 F:	include/linux/acpi.h
 
 ACPI BATTERY DRIVERS
-P:	Alexey Starikovskiy
-M:	astarikovskiy@suse.de
+M:	Alexey Starikovskiy <astarikovskiy@suse.de>
 L:	linux-acpi@vger.kernel.org
 W:	http://www.lesswatts.org/projects/acpi/
 S:	Supported
@@ -266,80 +244,69 @@ F:	drivers/acpi/battery.c
 F:	drivers/acpi/*sbs*
 
 ACPI EC DRIVER
-P:	Alexey Starikovskiy
-M:	astarikovskiy@suse.de
+M:	Alexey Starikovskiy <astarikovskiy@suse.de>
 L:	linux-acpi@vger.kernel.org
 W:	http://www.lesswatts.org/projects/acpi/
 S:	Supported
 F:	drivers/acpi/ec.c
 
 ACPI FAN DRIVER
-P:	Zhang Rui
-M:	rui.zhang@intel.com
+M:	Zhang Rui <rui.zhang@intel.com>
 L:	linux-acpi@vger.kernel.org
 W:	http://www.lesswatts.org/projects/acpi/
 S:	Supported
 F:	drivers/acpi/fan.c
 
 ACPI PCI HOTPLUG DRIVER
-P:	Kristen Carlson Accardi
-M:	kristen.c.accardi@intel.com
+M:	Kristen Carlson Accardi <kristen.c.accardi@intel.com>
 L:	linux-pci@vger.kernel.org
 S:	Supported
 F:	drivers/pci/hotplug/acpi*
 
 ACPI THERMAL DRIVER
-P:	Zhang Rui
-M:	rui.zhang@intel.com
+M:	Zhang Rui <rui.zhang@intel.com>
 L:	linux-acpi@vger.kernel.org
 W:	http://www.lesswatts.org/projects/acpi/
 S:	Supported
 F:	drivers/acpi/*thermal*
 
 ACPI VIDEO DRIVER
-P:	Zhang Rui
-M:	rui.zhang@intel.com
+M:	Zhang Rui <rui.zhang@intel.com>
 L:	linux-acpi@vger.kernel.org
 W:	http://www.lesswatts.org/projects/acpi/
 S:	Supported
 F:	drivers/acpi/video.c
 
 ACPI WMI DRIVER
-P:	Carlos Corbacho
-M:	carlos@strangeworlds.co.uk
+M:	Carlos Corbacho <carlos@strangeworlds.co.uk>
 L:	linux-acpi@vger.kernel.org
 W:	http://www.lesswatts.org/projects/acpi/
 S:	Maintained
 F:	drivers/platform/x86/wmi.c
 
 AD1889 ALSA SOUND DRIVER
-P:	Kyle McMartin
-M:	kyle@mcmartin.ca
-P:	Thibaut Varene
-M:	T-Bone@parisc-linux.org
+M:	Kyle McMartin <kyle@mcmartin.ca>
+M:	Thibaut Varene <T-Bone@parisc-linux.org>
 W:	http://wiki.parisc-linux.org/AD1889
 L:	linux-parisc@vger.kernel.org
 S:	Maintained
 F:	sound/pci/ad1889.*
 
 ADM1025 HARDWARE MONITOR DRIVER
-P:	Jean Delvare
-M:	khali@linux-fr.org
+M:	Jean Delvare <khali@linux-fr.org>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/adm1025
 F:	drivers/hwmon/adm1025.c
 
 ADM1029 HARDWARE MONITOR DRIVER
-P:	Corentin Labbe
-M:	corentin.labbe@geomatys.fr
+M:	Corentin Labbe <corentin.labbe@geomatys.fr>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	drivers/hwmon/adm1029.c
 
 ADM8211 WIRELESS DRIVER
-P:	Michael Wu
-M:	flamingice@sourmilk.net
+M:	Michael Wu <flamingice@sourmilk.net>
 L:	linux-wireless@vger.kernel.org
 W:	http://linuxwireless.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mwu/mac80211-drivers.git
@@ -347,35 +314,30 @@ S:	Maintained
 F:	drivers/net/wireless/adm8211.*
 
 ADT746X FAN DRIVER
-P:	Colin Leroy
-M:	colin@colino.net
+M:	Colin Leroy <colin@colino.net>
 S:	Maintained
 F:	drivers/macintosh/therm_adt746x.c
 
 ADVANSYS SCSI DRIVER
-P:	Matthew Wilcox
-M:	matthew@wil.cx
+M:	Matthew Wilcox <matthew@wil.cx>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	Documentation/scsi/advansys.txt
 F:	drivers/scsi/advansys.c
 
 AEDSP16 DRIVER
-P:	Riccardo Facchetti
-M:	fizban@tin.it
+M:	Riccardo Facchetti <fizban@tin.it>
 S:	Maintained
 F:	sound/oss/aedsp16.c
 
 AFFS FILE SYSTEM
-P:	Roman Zippel
-M:	zippel@linux-m68k.org
+M:	Roman Zippel <zippel@linux-m68k.org>
 S:	Maintained
 F:	Documentation/filesystems/affs.txt
 F:	fs/affs/
 
 AFS FILESYSTEM & AF_RXRPC SOCKET DOMAIN
-P:	David Howells
-M:	dhowells@redhat.com
+M:	David Howells <dhowells@redhat.com>
 L:	linux-afs@lists.infradead.org
 S:	Supported
 F:	fs/afs/
@@ -383,40 +345,35 @@ F:	include/net/af_rxrpc.h
 F:	net/rxrpc/af_rxrpc.c
 
 AGPGART DRIVER
-P:	David Airlie
-M:	airlied@linux.ie
+M:	David Airlie <airlied@linux.ie>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6.git
 S:	Maintained
 F:	drivers/char/agp/
 F:	include/linux/agp*
 
 AHA152X SCSI DRIVER
-P:	Juergen E. Fischer
-M:	fischer@norbit.de
+M:	"Juergen E. Fischer" <fischer@norbit.de>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/aha152x*
 F:	drivers/scsi/pcmcia/aha152x*
 
 AIC7XXX / AIC79XX SCSI DRIVER
-P:	Hannes Reinecke
-M:	hare@suse.de
+M:	Hannes Reinecke <hare@suse.de>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/aic7xxx/
 F:	drivers/scsi/aic7xxx_old/
 
 AIO
-P:	Benjamin LaHaise
-M:	bcrl@kvack.org
+M:	Benjamin LaHaise <bcrl@kvack.org>
 L:	linux-aio@kvack.org
 S:	Supported
 F:	fs/aio.c
 F:	include/linux/*aio*.h
 
 ALCATEL SPEEDTOUCH USB DRIVER
-P:	Duncan Sands
-M:	duncan.sands@free.fr
+M:	Duncan Sands <duncan.sands@free.fr>
 L:	linux-usb@vger.kernel.org
 W:	http://www.linux-usb.org/SpeedTouch/
 S:	Maintained
@@ -424,32 +381,27 @@ F:	drivers/usb/atm/speedtch.c
 F:	drivers/usb/atm/usbatm.c
 
 ALCHEMY AU1XX0 MMC DRIVER
-P:	Manuel Lauss
-M:	manuel.lauss@gmail.com
+M:	Manuel Lauss <manuel.lauss@gmail.com>
 S:	Maintained
 F:	drivers/mmc/host/au1xmmc.c
 
 ALI1563 I2C DRIVER
-P:	Rudolf Marek
-M:	r.marek@assembler.cz
+M:	Rudolf Marek <r.marek@assembler.cz>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	Documentation/i2c/busses/i2c-ali1563
 F:	drivers/i2c/busses/i2c-ali1563.c
 
 ALPHA PORT
-P:	Richard Henderson
-M:	rth@twiddle.net
+M:	Richard Henderson <rth@twiddle.net>
 S:	Odd Fixes for 2.4; Maintained for 2.6.
-P:	Ivan Kokshaysky
-M:	ink@jurassic.park.msu.ru
+M:	Ivan Kokshaysky <ink@jurassic.park.msu.ru>
 S:	Maintained for 2.4; PCI support for 2.6.
 L:	linux-alpha@vger.kernel.org
 F:	arch/alpha/
 
 AMD GEODE CS5536 USB DEVICE CONTROLLER DRIVER
-P:	Thomas Dahlmann
-M:	dahlmann.thomas@arcor.de
+M:	Thomas Dahlmann <dahlmann.thomas@arcor.de>
 L:	linux-geode@lists.infradead.org (moderated for non-subscribers)
 S:	Supported
 F:	drivers/usb/gadget/amd5536udc.*
@@ -466,8 +418,7 @@ F:	drivers/video/geode/
 F:	arch/x86/include/asm/geode.h
 
 AMD IOMMU (AMD-VI)
-P:	Joerg Roedel
-M:	joerg.roedel@amd.com
+M:	Joerg Roedel <joerg.roedel@amd.com>
 L:	iommu@lists.linux-foundation.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/joro/linux-2.6-iommu.git
 S:	Supported
@@ -475,40 +426,33 @@ F:	arch/x86/kernel/amd_iommu*.c
 F:	arch/x86/include/asm/amd_iommu*.h
 
 AMD MICROCODE UPDATE SUPPORT
-P:	Andreas Herrmann
-M:	andreas.herrmann3@amd.com
+M:	Andreas Herrmann <andreas.herrmann3@amd.com>
 L:	amd64-microcode@amd64.org
 S:	Supported
 F:	arch/x86/kernel/microcode_amd.c
 
 AMS (Apple Motion Sensor) DRIVER
-P:	Stelian Pop
-M:	stelian@popies.net
-P:	Michael Hanselmann
-M:	linux-kernel@hansmi.ch
+M:	Stelian Pop <stelian@popies.net>
+M:	Michael Hanselmann <linux-kernel@hansmi.ch>
 S:	Supported
 F:	drivers/hwmon/ams/
 
 AMSO1100 RNIC DRIVER
-P:	Tom Tucker
-M:	tom@opengridcomputing.com
-P:	Steve Wise
-M:	swise@opengridcomputing.com
+M:	Tom Tucker <tom@opengridcomputing.com>
+M:	Steve Wise <swise@opengridcomputing.com>
 L:	general@lists.openfabrics.org
 S:	Maintained
 F:	drivers/infiniband/hw/amso1100/
 
 AOA (Apple Onboard Audio) ALSA DRIVER
-P:	Johannes Berg
-M:	johannes@sipsolutions.net
+M:	Johannes Berg <johannes@sipsolutions.net>
 L:	linuxppc-dev@ozlabs.org
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 S:	Maintained
 F:	sound/aoa/
 
 APM DRIVER
-P:	Stephen Rothwell
-M:	sfr@canb.auug.org.au
+M:	Stephen Rothwell <sfr@canb.auug.org.au>
 L:	linux-laptop@vger.kernel.org
 W:	http://www.canb.auug.org.au/~sfr/
 S:	Supported
@@ -516,51 +460,44 @@ F:	arch/x86/kernel/apm_32.c
 F:	include/linux/apm_bios.h
 
 APPLE BCM5974 MULTITOUCH DRIVER
-P:	Henrik Rydberg
-M:	rydberg@euromail.se
+M:	Henrik Rydberg <rydberg@euromail.se>
 L:	linux-input@vger.kernel.org
 S:	Maintained
 F:	drivers/input/mouse/bcm5974.c
 
 APPLE SMC DRIVER
-P:	Nicolas Boichat
-M:	nicolas@boichat.ch
+M:	Nicolas Boichat <nicolas@boichat.ch>
 L:	mactel-linux-devel@lists.sourceforge.net
 S:	Maintained
 F:	drivers/hwmon/applesmc.c
 
 APPLETALK NETWORK LAYER
-P:	Arnaldo Carvalho de Melo
-M:	acme@ghostprotocols.net
+M:	Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
 S:	Maintained
 F:	drivers/net/appletalk/
 F:	net/appletalk/
 
 APPLETOUCH TOUCHPAD DRIVER
-P:	Johannes Berg
-M:	johannes@sipsolutions.net
+M:	Johannes Berg <johannes@sipsolutions.net>
 L:	linux-input@vger.kernel.org
 S:	Maintained
 F:	Documentation/input/appletouch.txt
 F:	drivers/input/mouse/appletouch.c
 
 ARC FRAMEBUFFER DRIVER
-P:	Jaya Kumar
-M:	jayalk@intworks.biz
+M:	Jaya Kumar <jayalk@intworks.biz>
 S:	Maintained
 F:	drivers/video/arcfb.c
 F:	drivers/video/fb_defio.c
 
 ARM MFM AND FLOPPY DRIVERS
-P:	Ian Molton
-M:	spyro@f2s.com
+M:	Ian Molton <spyro@f2s.com>
 S:	Maintained
 F:	arch/arm/lib/floppydma.S
 F:	arch/arm/include/asm/floppy.h
 
 ARM PORT
-P:	Russell King
-M:	linux@arm.linux.org.uk
+M:	Russell King <linux@arm.linux.org.uk>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.arm.linux.org.uk/
 S:	Maintained
@@ -571,79 +508,67 @@ S:	Orphan
 F:	drivers/mmc/host/mmci.*
 
 ARM/ADI ROADRUNNER MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 F:	arch/arm/mach-ixp23xx/
 F:	arch/arm/mach-ixp23xx/include/mach/
 
 ARM/ADS SPHERE MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/AFEB9260 MACHINE SUPPORT
-P:	Sergey Lapin
-M:	slapin@ossfans.org
+M:	Sergey Lapin <slapin@ossfans.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/AJECO 1ARM MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/ATMEL AT91RM9200 ARM ARCHITECTURE
-P:	Andrew Victor
-M:	linux@maxim.org.za
+M:	Andrew Victor <linux@maxim.org.za>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 W:	http://maxim.org.za/at91_26.html
 S:	Maintained
 
 ARM/CIRRUS LOGIC EP93XX ARM ARCHITECTURE
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/CIRRUS LOGIC EDB9315A MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/CLKDEV SUPPORT
-P:	Russell King
-M:	linux@arm.linux.org.uk
+M:	Russell King <linux@arm.linux.org.uk>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 F:	arch/arm/common/clkdev.c
 F:	arch/arm/include/asm/clkdev.h
 
 ARM/COMPULAB CM-X270/EM-X270 and CM-X300 MACHINE SUPPORT
-P:	Mike Rapoport
-M:	mike@compulab.co.il
+M:	Mike Rapoport <mike@compulab.co.il>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/CORGI MACHINE SUPPORT
-P:	Richard Purdie
-M:	rpurdie@rpsys.net
+M:	Richard Purdie <rpurdie@rpsys.net>
 S:	Maintained
 
 ARM/CORTINA SYSTEMS GEMINI ARM ARCHITECTURE
-P:	Paulius Zaleckas
-M:	paulius.zaleckas@teltonika.lt
+M:	Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 T:	git git://gitorious.org/linux-gemini/mainline.git
 S:	Maintained
 F:	arch/arm/mach-gemini/
 
 ARM/EBSA110 MACHINE SUPPORT
-P:	Russell King
-M:	linux@arm.linux.org.uk
+M:	Russell King <linux@arm.linux.org.uk>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.arm.linux.org.uk/
 S:	Maintained
@@ -651,12 +576,9 @@ F:	arch/arm/mach-ebsa110/
 F:	drivers/net/arm/am79c961a.*
 
 ARM/EZX SMARTPHONES (A780, A910, A1200, E680, ROKR E2 and ROKR E6)
-P:	Daniel Ribeiro
-M:	drwyrm@gmail.com
-P:	Stefan Schmidt
-M:	stefan@openezx.org
-P:	Harald Welte
-M:	laforge@openezx.org
+M:	Daniel Ribeiro <drwyrm@gmail.com>
+M:	Stefan Schmidt <stefan@openezx.org>
+M:	Harald Welte <laforge@openezx.org>
 L:	openezx-devel@lists.openezx.org (subscribers-only)
 W:	http://www.openezx.org/
 S:	Maintained
@@ -664,15 +586,13 @@ T:	topgit git://git.openezx.org/openezx.git
 F:	arch/arm/mach-pxa/ezx.c
 
 ARM/FARADAY FA526 PORT
-P:	Paulius Zaleckas
-M:	paulius.zaleckas@teltonika.lt
+M:	Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 F:	arch/arm/mm/*-fa*
 
 ARM/FOOTBRIDGE ARCHITECTURE
-P:	Russell King
-M:	linux@arm.linux.org.uk
+M:	Russell King <linux@arm.linux.org.uk>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.arm.linux.org.uk/
 S:	Maintained
@@ -680,175 +600,143 @@ F:	arch/arm/include/asm/hardware/dec21285.h
 F:	arch/arm/mach-footbridge/
 
 ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
-P:	Sascha Hauer
-M:	kernel@pengutronix.de
+M:	Sascha Hauer <kernel@pengutronix.de>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/GLOMATION GESBC9312SX MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/GUMSTIX MACHINE SUPPORT
-P:	Steve Sakoman
-M:	sakoman@gmail.com
+M:	Steve Sakoman <sakoman@gmail.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/H4700 (HP IPAQ HX4700) MACHINE SUPPORT
-P:	Philipp Zabel
-M:	philipp.zabel@gmail.com
+M:	Philipp Zabel <philipp.zabel@gmail.com>
 S:	Maintained
 F:	arch/arm/mach-pxa/hx4700.c
 F:	arch/arm/mach-pxa/include/mach/hx4700.h
 
 ARM/HP JORNADA 7XX MACHINE SUPPORT
-P:	Kristoffer Ericson
-M:	kristoffer.ericson@gmail.com
+M:	Kristoffer Ericson <kristoffer.ericson@gmail.com>
 W:	www.jlime.com
 S:	Maintained
 
 ARM/INTEL IOP32X ARM ARCHITECTURE
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
-P:	Dan Williams
-M:	dan.j.williams@intel.com
+M:	Lennert Buytenhek <kernel@wantstofly.org>
+M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Supported
 
 ARM/INTEL IOP33X ARM ARCHITECTURE
-P:	Dan Williams
-M:	dan.j.williams@intel.com
+M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Supported
 
 ARM/INTEL IOP13XX ARM ARCHITECTURE
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
-P:	Dan Williams
-M:	dan.j.williams@intel.com
+M:	Lennert Buytenhek <kernel@wantstofly.org>
+M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Supported
 
 ARM/INTEL IQ81342EX MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
-P:	Dan Williams
-M:	dan.j.williams@intel.com
+M:	Lennert Buytenhek <kernel@wantstofly.org>
+M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Supported
 
 ARM/INTEL IXP2000 ARM ARCHITECTURE
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/INTEL IXDP2850 MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/INTEL IXP23XX ARM ARCHITECTURE
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/INTEL XSC3 (MANZANO) ARM CORE
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
-P:	Dan Williams
-M:	dan.j.williams@intel.com
+M:	Lennert Buytenhek <kernel@wantstofly.org>
+M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Supported
 
 ARM/IP FABRICS DOUBLE ESPRESSO MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/LOGICPD PXA270 MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/MAGICIAN MACHINE SUPPORT
-P:	Philipp Zabel
-M:	philipp.zabel@gmail.com
+M:	Philipp Zabel <philipp.zabel@gmail.com>
 S:	Maintained
 
 ARM/MIOA701 MACHINE SUPPORT
-P:	Robert Jarzmik
-M:	robert.jarzmik@free.fr
+M:	Robert Jarzmik <robert.jarzmik@free.fr>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 F:	arch/arm/mach-pxa/mioa701.c
 S:	Maintained
 
 ARM/NEC MOBILEPRO 900/c MACHINE SUPPORT
-P:	Michael Petchkovsky
-M:	mkpetch@internode.on.net
+M:	Michael Petchkovsky <mkpetch@internode.on.net>
 S:	Maintained
 
 ARM/OPENMOKO NEO FREERUNNER (GTA02) MACHINE SUPPORT
-P:	Nelson Castillo
-M:	arhuaco@freaks-unidos.net
+M:	Nelson Castillo <arhuaco@freaks-unidos.net>
 L:	openmoko-kernel@lists.openmoko.org (subscribers-only)
 W:	http://wiki.openmoko.org/wiki/Neo_FreeRunner
 S:	Supported
 
 ARM/TOSA MACHINE SUPPORT
-P:	Dmitry Eremin-Solenikov
-M:	dbaryshkov@gmail.com
-P:	Dirk Opfer
-M:	dirk@opfer-online.de
+M:	Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
+M:	Dirk Opfer <dirk@opfer-online.de>
 S:	Maintained
 
 ARM/PALMTX,PALMT5,PALMLD,PALMTE2 SUPPORT
-P:	Marek Vasut
-M:	marek.vasut@gmail.com
+M:	Marek Vasut <marek.vasut@gmail.com>
 W:	http://hackndev.com
 S:	Maintained
 
 ARM/PALM TREO 680 SUPPORT
-P:	Tomas Cech
-M:	sleep_walker@suse.cz
+M:	Tomas Cech <sleep_walker@suse.cz>
 W:	http://hackndev.com
 S:	Maintained
 
 ARM/PALMZ72 SUPPORT
-P:	Sergey Lapin
-M:	slapin@ossfans.org
+M:	Sergey Lapin <slapin@ossfans.org>
 W:	http://hackndev.com
 S:	Maintained
 
 ARM/PLEB SUPPORT
-P:	Peter Chubb
-M:	pleb@gelato.unsw.edu.au
+M:	Peter Chubb <pleb@gelato.unsw.edu.au>
 W:	http://www.disy.cse.unsw.edu.au/Hardware/PLEB
 S:	Maintained
 
 ARM/PT DIGITAL BOARD PORT
-P:	Stefan Eletzhofer
-M:	stefan.eletzhofer@eletztrick.de
+M:	Stefan Eletzhofer <stefan.eletzhofer@eletztrick.de>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.arm.linux.org.uk/
 S:	Maintained
 
 ARM/RADISYS ENP2611 MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/RISCPC ARCHITECTURE
-P:	Russell King
-M:	linux@arm.linux.org.uk
+M:	Russell King <linux@arm.linux.org.uk>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.arm.linux.org.uk/
 S:	Maintained
@@ -862,14 +750,12 @@ F:	drivers/net/arm/ether*
 F:	drivers/scsi/arm/
 
 ARM/SHARK MACHINE SUPPORT
-P:	Alexander Schulz
-M:	alex@shark-linux.de
+M:	Alexander Schulz <alex@shark-linux.de>
 W:	http://www.shark-linux.de/shark.html
 S:	Maintained
 
 ARM/SAMSUNG ARM ARCHITECTURES
-P:	Ben Dooks
-M:	ben-linux@fluff.org
+M:	Ben Dooks <ben-linux@fluff.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.fluff.org/ben/linux/
 S:	Maintained
@@ -877,85 +763,73 @@ F:	arch/arm/plat-s3c/
 F:	arch/arm/plat-s3c24xx/
 
 ARM/S3C2410 ARM ARCHITECTURE
-P:	Ben Dooks
-M:	ben-linux@fluff.org
+M:	Ben Dooks <ben-linux@fluff.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.fluff.org/ben/linux/
 S:	Maintained
 F:	arch/arm/mach-s3c2410/
 
 ARM/S3C2440 ARM ARCHITECTURE
-P:	Ben Dooks
-M:	ben-linux@fluff.org
+M:	Ben Dooks <ben-linux@fluff.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.fluff.org/ben/linux/
 S:	Maintained
 F:	arch/arm/mach-s3c2440/
 
 ARM/S3C2442 ARM ARCHITECTURE
-P:	Ben Dooks
-M:	ben-linux@fluff.org
+M:	Ben Dooks <ben-linux@fluff.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.fluff.org/ben/linux/
 S:	Maintained
 F:	arch/arm/mach-s3c2442/
 
 ARM/S3C2443 ARM ARCHITECTURE
-P:	Ben Dooks
-M:	ben-linux@fluff.org
+M:	Ben Dooks <ben-linux@fluff.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.fluff.org/ben/linux/
 S:	Maintained
 F:	arch/arm/mach-s3c2443/
 
 ARM/S3C6400 ARM ARCHITECTURE
-P:	Ben Dooks
-M:	ben-linux@fluff.org
+M:	Ben Dooks <ben-linux@fluff.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.fluff.org/ben/linux/
 S:	Maintained
 F:	arch/arm/mach-s3c6400/
 
 ARM/S3C6410 ARM ARCHITECTURE
-P:	Ben Dooks
-M:	ben-linux@fluff.org
+M:	Ben Dooks <ben-linux@fluff.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.fluff.org/ben/linux/
 S:	Maintained
 F:	arch/arm/mach-s3c6410/
 
 ARM/TECHNOLOGIC SYSTEMS TS7250 MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/THECUS N2100 MACHINE SUPPORT
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 
 ARM/NUVOTON W90X900 ARM ARCHITECTURE
-P:	Wan ZongShun
-M:	mcuos.com@gmail.com
+M:	Wan ZongShun <mcuos.com@gmail.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 W:	http://www.mcuos.com
 S:	Maintained
 
 ARM/VFP SUPPORT
-P:	Russell King
-M:	linux@arm.linux.org.uk
+M:	Russell King <linux@arm.linux.org.uk>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.arm.linux.org.uk/
 S:	Maintained
 F:	arch/arm/vfp/
 
 ASUS ACPI EXTRAS DRIVER
-P:	Corentin Chary
-M:	corentincj@iksaif.net
-P:	Karol Kozimor
-M:	sziwan@users.sourceforge.net
+M:	Corentin Chary <corentincj@iksaif.net>
+M:	Karol Kozimor <sziwan@users.sourceforge.net>
 L:	acpi4asus-user@lists.sourceforge.net
 W:	http://acpi4asus.sf.net
 S:	Maintained
@@ -963,25 +837,21 @@ F:	arch/x86/kernel/acpi/boot.c
 F:	drivers/platform/x86/asus_acpi.c
 
 ASUS ASB100 HARDWARE MONITOR DRIVER
-P:	Mark M. Hoffman
-M:	mhoffman@lightlink.com
+M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	drivers/hwmon/asb100.c
 
 ASUS LAPTOP EXTRAS DRIVER
-P:	Corentin Chary
-M:	corentincj@iksaif.net
+M:	Corentin Chary <corentincj@iksaif.net>
 L:	acpi4asus-user@lists.sourceforge.net
 W:	http://acpi4asus.sf.net
 S:	Maintained
 F:	drivers/platform/x86/asus-laptop.c
 
 ASYNCHRONOUS TRANSFERS/TRANSFORMS (IOAT) API
-P:	Dan Williams
-M:	dan.j.williams@intel.com
-P:	Maciej Sosnowski
-M:	maciej.sosnowski@intel.com
+M:	Dan Williams <dan.j.williams@intel.com>
+M:	Maciej Sosnowski <maciej.sosnowski@intel.com>
 W:	http://sourceforge.net/projects/xscaleiop
 S:	Supported
 F:	Documentation/crypto/async-tx-api.txt
@@ -991,64 +861,49 @@ F:	include/linux/dmaengine.h
 F:	include/linux/async_tx.h
 
 ATA OVER ETHERNET (AOE) DRIVER
-P:	Ed L. Cashin
-M:	ecashin@coraid.com
+M:	"Ed L. Cashin" <ecashin@coraid.com>
 W:	http://www.coraid.com/support/linux
 S:	Supported
 F:	Documentation/aoe/
 F:	drivers/block/aoe/
 
 ATHEROS ATH5K WIRELESS DRIVER
-P:	Jiri Slaby
-M:	jirislaby@gmail.com
-P:	Nick Kossifidis
-M:	mickflemm@gmail.com
-P:	Luis R. Rodriguez
-M:	lrodriguez@atheros.com
-P:	Bob Copeland
-M:	me@bobcopeland.com
+M:	Jiri Slaby <jirislaby@gmail.com>
+M:	Nick Kossifidis <mickflemm@gmail.com>
+M:	"Luis R. Rodriguez" <lrodriguez@atheros.com>
+M:	Bob Copeland <me@bobcopeland.com>
 L:	linux-wireless@vger.kernel.org
 L:	ath5k-devel@lists.ath5k.org
 S:	Maintained
 F:	drivers/net/wireless/ath/ath5k/
 
 ATHEROS ATH9K WIRELESS DRIVER
-P:	Luis R. Rodriguez
-M:	lrodriguez@atheros.com
-P:	Jouni Malinen
-M:	jmalinen@atheros.com
-P:	Sujith Manoharan
-M:	Sujith.Manoharan@atheros.com
-P:	Vasanthakumar Thiagarajan
-M:	vasanth@atheros.com
-P:	Senthil Balasubramanian
-M:	senthilkumar@atheros.com
+M:	"Luis R. Rodriguez" <lrodriguez@atheros.com>
+M:	Jouni Malinen <jmalinen@atheros.com>
+M:	Sujith Manoharan <Sujith.Manoharan@atheros.com>
+M:	Vasanthakumar Thiagarajan <vasanth@atheros.com>
+M:	Senthil Balasubramanian <senthilkumar@atheros.com>
 L:	linux-wireless@vger.kernel.org
 L:	ath9k-devel@lists.ath9k.org
 S:	Supported
 F:	drivers/net/wireless/ath/ath9k/
 
 ATHEROS AR9170 WIRELESS DRIVER
-P:	Christian Lamparter
-M:	chunkeey@web.de
+M:	Christian Lamparter <chunkeey@web.de>
 L:	linux-wireless@vger.kernel.org
 W:	http://wireless.kernel.org/en/users/Drivers/ar9170
 S:	Maintained
 F:	drivers/net/wireless/ath/ar9170/
 
 ATI_REMOTE2 DRIVER
-P:	Ville Syrjala
-M:	syrjala@sci.fi
+M:	Ville Syrjala <syrjala@sci.fi>
 S:	Maintained
 F:	drivers/input/misc/ati_remote2.c
 
 ATLX ETHERNET DRIVERS
-P:	Jay Cliburn
-M:	jcliburn@gmail.com
-P:	Chris Snook
-M:	csnook@redhat.com
-P:	Jie Yang
-M:	jie.yang@atheros.com
+M:	Jay Cliburn <jcliburn@gmail.com>
+M:	Chris Snook <csnook@redhat.com>
+M:	Jie Yang <jie.yang@atheros.com>
 L:	atl1-devel@lists.sourceforge.net
 W:	http://sourceforge.net/projects/atl1
 W:	http://atl1.sourceforge.net
@@ -1056,8 +911,7 @@ S:	Maintained
 F:	drivers/net/atlx/
 
 ATM
-P:	Chas Williams
-M:	chas@cmf.nrl.navy.mil
+M:	Chas Williams <chas@cmf.nrl.navy.mil>
 L:	linux-atm-general@lists.sourceforge.net (subscribers-only)
 L:	netdev@vger.kernel.org
 W:	http://linux-atm.sourceforge.net
@@ -1066,8 +920,7 @@ F:	drivers/atm/
 F:	include/linux/atm*
 
 ATMEL AT91 MCI DRIVER
-P:	Nicolas Ferre
-M:	nicolas.ferre@atmel.com
+M:	Nicolas Ferre <nicolas.ferre@atmel.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 W:	http://www.atmel.com/products/AT91/
 W:	http://www.at91.com/
@@ -1075,49 +928,42 @@ S:	Maintained
 F:	drivers/mmc/host/at91_mci.c
 
 ATMEL AT91 / AT32 MCI DRIVER
-P:	Nicolas Ferre
-M:	nicolas.ferre@atmel.com
+M:	Nicolas Ferre <nicolas.ferre@atmel.com>
 S:	Maintained
 F:	drivers/mmc/host/atmel-mci.c
 F:	drivers/mmc/host/atmel-mci-regs.h
 
 ATMEL AT91 / AT32 SERIAL DRIVER
-P:	Haavard Skinnemoen
-M:	hskinnemoen@atmel.com
+M:	Haavard Skinnemoen <hskinnemoen@atmel.com>
 S:	Supported
 F:	drivers/serial/atmel_serial.c
 
 ATMEL LCDFB DRIVER
-P:	Nicolas Ferre
-M:	nicolas.ferre@atmel.com
+M:	Nicolas Ferre <nicolas.ferre@atmel.com>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/video/atmel_lcdfb.c
 F:	include/video/atmel_lcdc.h
 
 ATMEL MACB ETHERNET DRIVER
-P:	Haavard Skinnemoen
-M:	hskinnemoen@atmel.com
+M:	Haavard Skinnemoen <hskinnemoen@atmel.com>
 S:	Supported
 F:	drivers/net/macb.*
 
 ATMEL SPI DRIVER
-P:	Haavard Skinnemoen
-M:	hskinnemoen@atmel.com
+M:	Haavard Skinnemoen <hskinnemoen@atmel.com>
 S:	Supported
 F:	drivers/spi/atmel_spi.*
 
 ATMEL USBA UDC DRIVER
-P:	Haavard Skinnemoen
-M:	hskinnemoen@atmel.com
+M:	Haavard Skinnemoen <hskinnemoen@atmel.com>
 L:	kernel@avr32linux.org
 W:	http://avr32linux.org/twiki/bin/view/Main/AtmelUsbDeviceDriver
 S:	Supported
 F:	drivers/usb/gadget/atmel_usba_udc.*
 
 ATMEL WIRELESS DRIVER
-P:	Simon Kelley
-M:	simon@thekelleys.org.uk
+M:	Simon Kelley <simon@thekelleys.org.uk>
 L:	linux-wireless@vger.kernel.org
 W:	http://www.thekelleys.org.uk/atmel
 W:	http://atmelwlandriver.sourceforge.net/
@@ -1125,10 +971,8 @@ S:	Maintained
 F:	drivers/net/wireless/atmel*
 
 AUDIT SUBSYSTEM
-P:	Al Viro
-M:	viro@zeniv.linux.org.uk
-P:	Eric Paris
-M:	eparis@redhat.com
+M:	Al Viro <viro@zeniv.linux.org.uk>
+M:	Eric Paris <eparis@redhat.com>
 L:	linux-audit@redhat.com (subscribers-only)
 W:	http://people.redhat.com/sgrubb/audit/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current.git
@@ -1137,8 +981,7 @@ F:	include/linux/audit.h
 F:	kernel/audit*
 
 AUXILIARY DISPLAY DRIVERS
-P:	Miguel Ojeda Sandonis
-M:	miguel.ojeda.sandonis@gmail.com
+M:	Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
 W:	http://miguelojeda.es/auxdisplay.htm
 W:	http://jair.lab.fi.uva.es/~migojed/auxdisplay.htm
 S:	Maintained
@@ -1146,8 +989,7 @@ F:	drivers/auxdisplay/
 F:	include/linux/cfag12864b.h
 
 AVR32 ARCHITECTURE
-P:	Haavard Skinnemoen
-M:	hskinnemoen@atmel.com
+M:	Haavard Skinnemoen <hskinnemoen@atmel.com>
 W:	http://www.atmel.com/products/AVR32/
 W:	http://avr32linux.org/
 W:	http://avrfreaks.net/
@@ -1155,14 +997,12 @@ S:	Supported
 F:	arch/avr32/
 
 AVR32/AT32AP MACHINE SUPPORT
-P:	Haavard Skinnemoen
-M:	hskinnemoen@atmel.com
+M:	Haavard Skinnemoen <hskinnemoen@atmel.com>
 S:	Supported
 F:	arch/avr32/mach-at32ap/
 
 AX.25 NETWORK LAYER
-P:	Ralf Baechle
-M:	ralf@linux-mips.org
+M:	Ralf Baechle <ralf@linux-mips.org>
 L:	linux-hams@vger.kernel.org
 W:	http://www.linux-ax25.org/
 S:	Maintained
@@ -1171,128 +1011,110 @@ F:	include/net/ax25.h
 F:	net/ax25/
 
 B43 WIRELESS DRIVER
-P:	Michael Buesch
-M:	mb@bu3sch.de
-P:	Stefano Brivio
-M:	stefano.brivio@polimi.it
+M:	Michael Buesch <mb@bu3sch.de>
+M:	Stefano Brivio <stefano.brivio@polimi.it>
 L:	linux-wireless@vger.kernel.org
 W:	http://linuxwireless.org/en/users/Drivers/b43
 S:	Maintained
 F:	drivers/net/wireless/b43/
 
 B43LEGACY WIRELESS DRIVER
-P:	Larry Finger
-M:	Larry.Finger@lwfinger.net
-P:	Stefano Brivio
-M:	stefano.brivio@polimi.it
+M:	Larry Finger <Larry.Finger@lwfinger.net>
+M:	Stefano Brivio <stefano.brivio@polimi.it>
 L:	linux-wireless@vger.kernel.org
 W:	http://linuxwireless.org/en/users/Drivers/b43
 S:	Maintained
 F:	drivers/net/wireless/b43legacy/
 
 BACKLIGHT CLASS/SUBSYSTEM
-P:	Richard Purdie
-M:	rpurdie@rpsys.net
+M:	Richard Purdie <rpurdie@rpsys.net>
 S:	Maintained
 F:	drivers/video/backlight/
 F:	include/linux/backlight.h
 
 BAYCOM/HDLCDRV DRIVERS FOR AX.25
-P:	Thomas Sailer
-M:	t.sailer@alumni.ethz.ch
+M:	Thomas Sailer <t.sailer@alumni.ethz.ch>
 L:	linux-hams@vger.kernel.org
 W:	http://www.baycom.org/~tom/ham/ham.html
 S:	Maintained
 F:	drivers/net/hamradio/baycom*
 
 BEFS FILE SYSTEM
-P:	Sergey S. Kostyliov
-M:	rathamahata@php4.ru
+M:	"Sergey S. Kostyliov" <rathamahata@php4.ru>
 S:	Maintained
 F:	Documentation/filesystems/befs.txt
 F:	fs/befs/
 
 BFS FILE SYSTEM
-P:	Tigran A. Aivazian
-M:	tigran@aivazian.fsnet.co.uk
+M:	"Tigran A. Aivazian" <tigran@aivazian.fsnet.co.uk>
 S:	Maintained
 F:	Documentation/filesystems/bfs.txt
 F:	fs/bfs/
 F:	include/linux/bfs_fs.h
 
 BLACKFIN ARCHITECTURE
-P:	Mike Frysinger
-M:	vapier@gentoo.org
+M:	Mike Frysinger <vapier@gentoo.org>
 L:	uclinux-dist-devel@blackfin.uclinux.org
 W:	http://blackfin.uclinux.org
 S:	Supported
 F:	arch/blackfin/
 
 BLACKFIN EMAC DRIVER
-P:	Michael Hennerich
-M:	michael.hennerich@analog.com
+M:	Michael Hennerich <michael.hennerich@analog.com>
 L:	uclinux-dist-devel@blackfin.uclinux.org
 W:	http://blackfin.uclinux.org
 S:	Supported
 F:	drivers/net/bfin_mac.*
 
 BLACKFIN RTC DRIVER
-P:	Mike Frysinger
-M:	vapier.adi@gmail.com
+M:	Mike Frysinger <vapier.adi@gmail.com>
 L:	uclinux-dist-devel@blackfin.uclinux.org
 W:	http://blackfin.uclinux.org
 S:	Supported
 F:	drivers/rtc/rtc-bfin.c
 
 BLACKFIN SERIAL DRIVER
-P:	Sonic Zhang
-M:	sonic.zhang@analog.com
+M:	Sonic Zhang <sonic.zhang@analog.com>
 L:	uclinux-dist-devel@blackfin.uclinux.org
 W:	http://blackfin.uclinux.org
 S:	Supported
 F:	drivers/serial/bfin_5xx.c
 
 BLACKFIN WATCHDOG DRIVER
-P:	Mike Frysinger
-M:	vapier.adi@gmail.com
+M:	Mike Frysinger <vapier.adi@gmail.com>
 L:	uclinux-dist-devel@blackfin.uclinux.org
 W:	http://blackfin.uclinux.org
 S:	Supported
 F:	drivers/watchdog/bfin_wdt.c
 
 BLACKFIN I2C TWI DRIVER
-P:	Sonic Zhang
-M:	sonic.zhang@analog.com
+M:	Sonic Zhang <sonic.zhang@analog.com>
 L:	uclinux-dist-devel@blackfin.uclinux.org
 W:	http://blackfin.uclinux.org/
 S:	Supported
 F:	drivers/i2c/busses/i2c-bfin-twi.c
 
 BLOCK LAYER
-P:	Jens Axboe
-M:	axboe@kernel.dk
+M:	Jens Axboe <axboe@kernel.dk>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux-2.6-block.git
 S:	Maintained
 F:	block/
 
 BLOCK2MTD DRIVER
-P:	Joern Engel
-M:	joern@lazybastard.org
+M:	Joern Engel <joern@lazybastard.org>
 L:	linux-mtd@lists.infradead.org
 S:	Maintained
 F:	drivers/mtd/devices/block2mtd.c
 
 BLUETOOTH DRIVERS
-P:	Marcel Holtmann
-M:	marcel@holtmann.org
+M:	Marcel Holtmann <marcel@holtmann.org>
 L:	linux-bluetooth@vger.kernel.org
 W:	http://www.bluez.org/
 S:	Maintained
 F:	drivers/bluetooth/
 
 BLUETOOTH SUBSYSTEM
-P:	Marcel Holtmann
-M:	marcel@holtmann.org
+M:	Marcel Holtmann <marcel@holtmann.org>
 L:	linux-bluetooth@vger.kernel.org
 W:	http://www.bluez.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-2.6.git
@@ -1301,8 +1123,7 @@ F:	net/bluetooth/
 F:	include/net/bluetooth/
 
 BONDING DRIVER
-P:	Jay Vosburgh
-M:	fubar@us.ibm.com
+M:	Jay Vosburgh <fubar@us.ibm.com>
 L:	bonding-devel@lists.sourceforge.net
 W:	http://sourceforge.net/projects/bonding/
 S:	Supported
@@ -1310,54 +1131,46 @@ F:	drivers/net/bonding/
 F:	include/linux/if_bonding.h
 
 BROADCOM B44 10/100 ETHERNET DRIVER
-P:	Gary Zambrano
-M:	zambrano@broadcom.com
+M:	Gary Zambrano <zambrano@broadcom.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/b44.*
 
 BROADCOM BNX2 GIGABIT ETHERNET DRIVER
-P:	Michael Chan
-M:	mchan@broadcom.com
+M:	Michael Chan <mchan@broadcom.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/bnx2.*
 F:	drivers/net/bnx2_*
 
 BROADCOM BNX2X 10 GIGABIT ETHERNET DRIVER
-P:	Eilon Greenstein
-M:	eilong@broadcom.com
+M:	Eilon Greenstein <eilong@broadcom.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/bnx2x*
 
 BROADCOM TG3 GIGABIT ETHERNET DRIVER
-P:	Matt Carlson
-M:	mcarlson@broadcom.com
-P:	Michael Chan
-M:	mchan@broadcom.com
+M:	Matt Carlson <mcarlson@broadcom.com>
+M:	Michael Chan <mchan@broadcom.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/tg3.*
 
 BSG (block layer generic sg v4 driver)
-P:	FUJITA Tomonori
-M:	fujita.tomonori@lab.ntt.co.jp
+M:	FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
 L:	linux-scsi@vger.kernel.org
 S:	Supported
 F:	block/bsg.c
 F:	include/linux/bsg.h
 
 BT8XXGPIO DRIVER
-P:	Michael Buesch
-M:	mb@bu3sch.de
+M:	Michael Buesch <mb@bu3sch.de>
 W:	http://bu3sch.de/btgpio.php
 S:	Maintained
 F:	drivers/gpio/bt8xxgpio.c
 
 BTRFS FILE SYSTEM
-P:	Chris Mason
-M:	chris.mason@oracle.com
+M:	Chris Mason <chris.mason@oracle.com>
 L:	linux-btrfs@vger.kernel.org
 W:	http://btrfs.wiki.kernel.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable.git
@@ -1366,8 +1179,7 @@ F:	Documentation/filesystems/btrfs.txt
 F:	fs/btrfs/
 
 BTTV VIDEO4LINUX DRIVER
-P:	Mauro Carvalho Chehab
-M:	mchehab@infradead.org
+M:	Mauro Carvalho Chehab <mchehab@infradead.org>
 L:	linux-media@vger.kernel.org
 W:	http://linuxtv.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
@@ -1376,16 +1188,14 @@ F:	Documentation/video4linux/bttv/
 F:	drivers/media/video/bt8xx/bttv*
 
 CACHEFILES: FS-CACHE BACKEND FOR CACHING ON MOUNTED FILESYSTEMS
-P:	David Howells
-M:	dhowells@redhat.com
+M:	David Howells <dhowells@redhat.com>
 L:	linux-cachefs@redhat.com
 S:	Supported
 F:	Documentation/filesystems/caching/cachefiles.txt
 F:	fs/cachefiles/
 
 CAFE CMOS INTEGRATED CAMERA CONTROLLER DRIVER
-P:	Jonathan Corbet
-M:	corbet@lwn.net
+M:	Jonathan Corbet <corbet@lwn.net>
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 S:	Maintained
@@ -1393,10 +1203,8 @@ F:	Documentation/video4linux/cafe_ccic
 F:	drivers/media/video/cafe_ccic*
 
 CALGARY x86-64 IOMMU
-P:	Muli Ben-Yehuda
-M:	muli@il.ibm.com
-P:	Jon D. Mason
-M:	jdmason@kudzu.us
+M:	Muli Ben-Yehuda <muli@il.ibm.com>
+M:	"Jon D. Mason" <jdmason@kudzu.us>
 L:	discuss@x86-64.org
 S:	Maintained
 F:	arch/x86/kernel/pci-calgary_64.c
@@ -1405,10 +1213,8 @@ F:	arch/x86/include/asm/calgary.h
 F:	arch/x86/include/asm/tce.h
 
 CAN NETWORK LAYER
-P:	Urs Thuermann
-M:	urs.thuermann@volkswagen.de
-P:	Oliver Hartkopp
-M:	oliver.hartkopp@volkswagen.de
+M:	Urs Thuermann <urs.thuermann@volkswagen.de>
+M:	Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
 L:	socketcan-core@lists.berlios.de (subscribers-only)
 W:	http://developer.berlios.de/projects/socketcan/
 S:	Maintained
@@ -1417,15 +1223,13 @@ F:	include/linux/can/
 F:	include/linux/can.h
 
 CAN NETWORK DRIVERS
-P:	Wolfgang Grandegger
-M:	wg@grandegger.com
+M:	Wolfgang Grandegger <wg@grandegger.com>
 L:	socketcan-core@lists.berlios.de (subscribers-only)
 W:	http://developer.berlios.de/projects/socketcan/
 S:	Maintained
 
 CELL BROADBAND ENGINE ARCHITECTURE
-P:	Arnd Bergmann
-M:	arnd@arndb.de
+M:	Arnd Bergmann <arnd@arndb.de>
 L:	linuxppc-dev@ozlabs.org
 L:	cbe-oss-dev@ozlabs.org
 W:	http://www.ibm.com/developerworks/power/cell/
@@ -1436,8 +1240,7 @@ F:	arch/powerpc/oprofile/*cell*
 F:	arch/powerpc/platforms/cell/
 
 CERTIFIED WIRELESS USB (WUSB) SUBSYSTEM:
-P:	David Vrabel
-M:	david.vrabel@csr.com
+M:	David Vrabel <david.vrabel@csr.com>
 L:	linux-usb@vger.kernel.org
 S:	Supported
 F:	Documentation/usb/WUSB-Design-overview.txt
@@ -1446,8 +1249,7 @@ F:	drivers/usb/wusbcore/
 F:	include/linux/usb/wusb*
 
 CFAG12864B LCD DRIVER
-P:	Miguel Ojeda Sandonis
-M:	miguel.ojeda.sandonis@gmail.com
+M:	Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
 W:	http://miguelojeda.es/auxdisplay.htm
 W:	http://jair.lab.fi.uva.es/~migojed/auxdisplay.htm
 S:	Maintained
@@ -1455,8 +1257,7 @@ F:	drivers/auxdisplay/cfag12864b.c
 F:	include/linux/cfag12864b.h
 
 CFAG12864BFB LCD FRAMEBUFFER DRIVER
-P:	Miguel Ojeda Sandonis
-M:	miguel.ojeda.sandonis@gmail.com
+M:	Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
 W:	http://miguelojeda.es/auxdisplay.htm
 W:	http://jair.lab.fi.uva.es/~migojed/auxdisplay.htm
 S:	Maintained
@@ -1464,8 +1265,7 @@ F:	drivers/auxdisplay/cfag12864bfb.c
 F:	include/linux/cfag12864b.h
 
 CFG80211 and NL80211
-P:	Johannes Berg
-M:	johannes@sipsolutions.net
+M:	Johannes Berg <johannes@sipsolutions.net>
 L:	linux-wireless@vger.kernel.org
 S:	Maintained
 F:	include/linux/nl80211.h
@@ -1474,57 +1274,47 @@ F:	net/wireless/*
 X:	net/wireless/wext*
 
 CHECKPATCH
-P:	Andy Whitcroft
-M:	apw@canonical.com
+M:	Andy Whitcroft <apw@canonical.com>
 S:	Supported
 F:	scripts/checkpatch.pl
 
 CISCO 10G ETHERNET DRIVER
-P:	Scott Feldman
-M:	scofeldm@cisco.com
-P:	Joe Eykholt
-M:	jeykholt@cisco.com
+M:	Scott Feldman <scofeldm@cisco.com>
+M:	Joe Eykholt <jeykholt@cisco.com>
 S:	Supported
 F:	drivers/net/enic/
 
 CIRRUS LOGIC EP93XX ETHERNET DRIVER
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/arm/ep93xx_eth.c
 
 CIRRUS LOGIC EP93XX OHCI USB HOST DRIVER
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/host/ohci-ep93xx.c
 
 CIRRUS LOGIC CS4270 SOUND DRIVER
-P:	Timur Tabi
-M:	timur@freescale.com
+M:	Timur Tabi <timur@freescale.com>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 S:	Supported
 F:	sound/soc/codecs/cs4270*
 
 CLK API
-P:	Russell King
-M:	linux@arm.linux.org.uk
+M:	Russell King <linux@arm.linux.org.uk>
 F:	include/linux/clk.h
 
 CISCO FCOE HBA DRIVER
-P:	Abhijeet Joglekar
-M:	abjoglek@cisco.com
-P:	Joe Eykholt
-M:	jeykholt@cisco.com
+M:	Abhijeet Joglekar <abjoglek@cisco.com>
+M:	Joe Eykholt <jeykholt@cisco.com>
 L:	linux-scsi@vger.kernel.org
 S:	Supported
 F:	drivers/scsi/fnic/
 
 CODA FILE SYSTEM
-P:	Jan Harkes
-M:	jaharkes@cs.cmu.edu
+M:	Jan Harkes <jaharkes@cs.cmu.edu>
 M:	coda@cs.cmu.edu
 L:	codalist@coda.cs.cmu.edu
 W:	http://www.coda.cs.cmu.edu/
@@ -1534,8 +1324,7 @@ F:	fs/coda/
 F:	include/linux/coda*.h
 
 COMMON INTERNET FILE SYSTEM (CIFS)
-P:	Steve French
-M:	sfrench@samba.org
+M:	Steve French <sfrench@samba.org>
 L:	linux-cifs-client@lists.samba.org
 L:	samba-technical@lists.samba.org
 W:	http://linux-cifs.samba.org/
@@ -1545,67 +1334,57 @@ F:	Documentation/filesystems/cifs.txt
 F:	fs/cifs/
 
 COMPACTPCI HOTPLUG CORE
-P:	Scott Murray
-M:	scott@spiteful.org
+M:	Scott Murray <scott@spiteful.org>
 L:	linux-pci@vger.kernel.org
 S:	Maintained
 F:	drivers/pci/hotplug/cpci_hotplug*
 
 COMPACTPCI HOTPLUG ZIATECH ZT5550 DRIVER
-P:	Scott Murray
-M:	scott@spiteful.org
+M:	Scott Murray <scott@spiteful.org>
 L:	linux-pci@vger.kernel.org
 S:	Maintained
 F:	drivers/pci/hotplug/cpcihp_zt5550.*
 
 COMPACTPCI HOTPLUG GENERIC DRIVER
-P:	Scott Murray
-M:	scott@spiteful.org
+M:	Scott Murray <scott@spiteful.org>
 L:	linux-pci@vger.kernel.org
 S:	Maintained
 F:	drivers/pci/hotplug/cpcihp_generic.c
 
 COMPAL LAPTOP SUPPORT
-P:	Cezary Jackiewicz
-M:	cezary.jackiewicz@gmail.com
+M:	Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
 S:	Maintained
 F:	drivers/platform/x86/compal-laptop.c
 
 COMPUTONE INTELLIPORT MULTIPORT CARD
-P:	Michael H. Warfield
-M:	mhw@wittsend.com
+M:	"Michael H. Warfield" <mhw@wittsend.com>
 W:	http://www.wittsend.com/computone.html
 S:	Maintained
 F:	Documentation/serial/computone.txt
 F:	drivers/char/ip2/
 
 CONEXANT ACCESSRUNNER USB DRIVER
-P:	Simon Arlott
-M:	cxacru@fire.lp0.eu
+M:	Simon Arlott <cxacru@fire.lp0.eu>
 L:	accessrunner-general@lists.sourceforge.net
 W:	http://accessrunner.sourceforge.net/
 S:	Maintained
 F:	drivers/usb/atm/cxacru.c
 
 CONFIGFS
-P:	Joel Becker
-M:	joel.becker@oracle.com
+M:	Joel Becker <joel.becker@oracle.com>
 S:	Supported
 F:	fs/configfs/
 F:	include/linux/configfs.h
 
 CONNECTOR
-P:	Evgeniy Polyakov
-M:	zbr@ioremap.net
+M:	Evgeniy Polyakov <zbr@ioremap.net>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/connector/
 
 CONTROL GROUPS (CGROUPS)
-P:	Paul Menage
-M:	menage@google.com
-P:	Li Zefan
-M:	lizf@cn.fujitsu.com
+M:	Paul Menage <menage@google.com>
+M:	Li Zefan <lizf@cn.fujitsu.com>
 L:	containers@lists.linux-foundation.org
 S:	Maintained
 F:	include/linux/cgroup*
@@ -1613,30 +1392,26 @@ F:	kernel/cgroup*
 F:	mm/*cgroup*
 
 CORETEMP HARDWARE MONITORING DRIVER
-P:	Rudolf Marek
-M:	r.marek@assembler.cz
+M:	Rudolf Marek <r.marek@assembler.cz>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/coretemp
 F:	drivers/hwmon/coretemp.c
 
 COSA/SRP SYNC SERIAL DRIVER
-P:	Jan "Yenya" Kasprzak
-M:	kas@fi.muni.cz
+M:	Jan "Yenya" Kasprzak <kas@fi.muni.cz>
 W:	http://www.fi.muni.cz/~kas/cosa/
 S:	Maintained
 F:	drivers/net/wan/cosa*
 
 CPMAC ETHERNET DRIVER
-P:	Florian Fainelli
-M:	florian@openwrt.org
+M:	Florian Fainelli <florian@openwrt.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/cpmac.c
 
 CPU FREQUENCY DRIVERS
-P:	Dave Jones
-M:	davej@redhat.com
+M:	Dave Jones <davej@redhat.com>
 L:	cpufreq@vger.kernel.org
 W:	http://www.codemonkey.org.uk/projects/cpufreq/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq.git
@@ -1646,15 +1421,13 @@ F:	drivers/cpufreq/
 F:	include/linux/cpufreq.h
 
 CPUID/MSR DRIVER
-P:	H. Peter Anvin
-M:	hpa@zytor.com
+M:	"H. Peter Anvin" <hpa@zytor.com>
 S:	Maintained
 F:	arch/x86/kernel/cpuid.c
 F:	arch/x86/kernel/msr.c
 
 CPUSETS
-P:	Paul Menage
-M:	menage@google.com
+M:	Paul Menage <menage@google.com>
 W:	http://www.bullopensource.org/cpuset/
 W:	http://oss.sgi.com/projects/cpusets/
 S:	Supported
@@ -1669,20 +1442,16 @@ F:	Documentation/filesystems/cramfs.txt
 F:	fs/cramfs/
 
 CRIS PORT
-P:	Mikael Starvik
-M:	starvik@axis.com
-P:	Jesper Nilsson
-M:	jesper.nilsson@axis.com
+M:	Mikael Starvik <starvik@axis.com>
+M:	Jesper Nilsson <jesper.nilsson@axis.com>
 L:	linux-cris-kernel@axis.com
 W:	http://developer.axis.com
 S:	Maintained
 F:	arch/cris/
 
 CRYPTO API
-P:	Herbert Xu
-M:	herbert@gondor.apana.org.au
-P:	David S. Miller
-M:	davem@davemloft.net
+M:	Herbert Xu <herbert@gondor.apana.org.au>
+M:	"David S. Miller" <davem@davemloft.net>
 L:	linux-crypto@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6.git
 S:	Maintained
@@ -1693,22 +1462,18 @@ F:	drivers/crypto/
 F:	include/crypto/
 
 CRYPTOGRAPHIC RANDOM NUMBER GENERATOR
-P:	Neil Horman
-M:	nhorman@tuxdriver.com
+M:	Neil Horman <nhorman@tuxdriver.com>
 L:	linux-crypto@vger.kernel.org
 S:	Maintained
 
 CS5535 Audio ALSA driver
-P:	Jaya Kumar
-M:	jayakumar.alsa@gmail.com
+M:	Jaya Kumar <jayakumar.alsa@gmail.com>
 S:	Maintained
 F:	sound/pci/cs5535audio/
 
 CX18 VIDEO4LINUX DRIVER
-P:	Hans Verkuil
-M:	hverkuil@xs4all.nl
-P:	Andy Walls
-M:	awalls@radix.net
+M:	Hans Verkuil <hverkuil@xs4all.nl>
+M:	Andy Walls <awalls@radix.net>
 L:	ivtv-devel@ivtvdriver.org
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
@@ -1719,32 +1484,28 @@ F:	Documentation/video4linux/cx18.txt
 F:	drivers/media/video/cx18/
 
 CXGB3 ETHERNET DRIVER (CXGB3)
-P:	Divy Le Ray
-M:	divy@chelsio.com
+M:	Divy Le Ray <divy@chelsio.com>
 L:	netdev@vger.kernel.org
 W:	http://www.chelsio.com
 S:	Supported
 F:	drivers/net/cxgb3/
 
 CXGB3 IWARP RNIC DRIVER (IW_CXGB3)
-P:	Steve Wise
-M:	swise@chelsio.com
+M:	Steve Wise <swise@chelsio.com>
 L:	general@lists.openfabrics.org
 W:	http://www.openfabrics.org
 S:	Supported
 F:	drivers/infiniband/hw/cxgb3/
 
 CYBERPRO FB DRIVER
-P:	Russell King
-M:	linux@arm.linux.org.uk
+M:	Russell King <linux@arm.linux.org.uk>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 W:	http://www.arm.linux.org.uk/
 S:	Maintained
 F:	drivers/video/cyber2000fb.*
 
 CYCLADES 2X SYNC CARD DRIVER
-P:	Arnaldo Carvalho de Melo
-M:	acme@ghostprotocols.net
+M:	Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
 W:	http://oops.ghostprotocols.net:81/blog
 S:	Maintained
 F:	drivers/net/wan/cycx*
@@ -1761,8 +1522,7 @@ S:	Orphan
 F:	drivers/net/wan/pc300*
 
 DAMA SLAVE for AX.25
-P:	Joerg Reuter
-M:	jreuter@yaina.de
+M:	Joerg Reuter <jreuter@yaina.de>
 W:	http://yaina.de/jreuter/
 W:	http://www.qsl.net/dl1bke/
 L:	linux-hams@vger.kernel.org
@@ -1776,29 +1536,23 @@ F:	net/ax25/ax25_timer.c
 F:	net/ax25/sysctl_net_ax25.c
 
 DAVICOM FAST ETHERNET (DMFE) NETWORK DRIVER
-P:	Tobias Ringstrom
-M:	tori@unhappy.mine.nu
+M:	Tobias Ringstrom <tori@unhappy.mine.nu>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	Documentation/networking/dmfe.txt
 F:	drivers/net/tulip/dmfe.c
 
 DC390/AM53C974 SCSI driver
-P:	Kurt Garloff
-M:	garloff@suse.de
+M:	Kurt Garloff <garloff@suse.de>
 W:	http://www.garloff.de/kurt/linux/dc390/
-P:	Guennadi Liakhovetski
-M:	g.liakhovetski@gmx.de
+M:	Guennadi Liakhovetski <g.liakhovetski@gmx.de>
 S:	Maintained
 F:	drivers/scsi/tmscsim.*
 
 DC395x SCSI driver
-P:	Oliver Neukum
-M:	oliver@neukum.name
-P:	Ali Akcaagac
-M:	aliakc@web.de
-P:	Jamie Lenehan
-M:	lenehan@twibble.org
+M:	Oliver Neukum <oliver@neukum.name>
+M:	Ali Akcaagac <aliakc@web.de>
+M:	Jamie Lenehan <lenehan@twibble.org>
 W:	http://twibble.org/dist/dc395x/
 L:	dc395x@twibble.org
 L:	http://lists.twibble.org/mailman/listinfo/dc395x/
@@ -1807,8 +1561,7 @@ F:	Documentation/scsi/dc395x.txt
 F:	drivers/scsi/dc395x.*
 
 DCCP PROTOCOL
-P:	Arnaldo Carvalho de Melo
-M:	acme@ghostprotocols.net
+M:	Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
 L:	dccp@vger.kernel.org
 W:	http://linux-net.osdl.org/index.php/DCCP
 S:	Maintained
@@ -1817,8 +1570,7 @@ F:	include/linux/tfrc.h
 F:	net/dccp/
 
 DECnet NETWORK LAYER
-P:	Christine Caulfield
-M:	christine.caulfield@googlemail.com
+M:	Christine Caulfield <christine.caulfield@googlemail.com>
 W:	http://linux-decnet.sourceforge.net
 L:	linux-decnet-user@lists.sourceforge.net
 S:	Maintained
@@ -1826,40 +1578,34 @@ F:	Documentation/networking/decnet.txt
 F:	net/decnet/
 
 DEFXX FDDI NETWORK DRIVER
-P:	Maciej W. Rozycki
-M:	macro@linux-mips.org
+M:	"Maciej W. Rozycki" <macro@linux-mips.org>
 S:	Maintained
 F:	drivers/net/defxx.*
 
 DELL LAPTOP DRIVER
-P:	Matthew Garrett
-M:	mjg59@srcf.ucam.org
+M:	Matthew Garrett <mjg59@srcf.ucam.org>
 S:	Maintained
 F:	drivers/platform/x86/dell-laptop.c
 
 DELL LAPTOP SMM DRIVER
-P:	Massimo Dal Zotto
-M:	dz@debian.org
+M:	Massimo Dal Zotto <dz@debian.org>
 W:	http://www.debian.org/~dz/i8k/
 S:	Maintained
 F:	drivers/char/i8k.c
 F:	include/linux/i8k.h
 
 DELL SYSTEMS MANAGEMENT BASE DRIVER (dcdbas)
-P:	Doug Warzecha
-M:	Douglas_Warzecha@dell.com
+M:	Doug Warzecha <Douglas_Warzecha@dell.com>
 S:	Maintained
 F:	Documentation/dcdbas.txt
 F:	drivers/firmware/dcdbas.*
 
 DELL WMI EXTRAS DRIVER
-P:	Matthew Garrett
-M:	mjg59@srcf.ucam.org
+M:	Matthew Garrett <mjg59@srcf.ucam.org>
 S:	Maintained
 
 DEVICE NUMBER REGISTRY
-P:	Torben Mathiasen
-M:	device@lanana.org
+M:	Torben Mathiasen <device@lanana.org>
 W:	http://lanana.org/docs/device-list/index.html
 S:	Maintained
 
@@ -1874,8 +1620,7 @@ F:	include/linux/device-mapper.h
 F:	include/linux/dm-*.h
 
 DIGI INTL. EPCA DRIVER
-P:	Digi International, Inc
-M:	Eng.Linux@digi.com
+M:	"Digi International, Inc" <Eng.Linux@digi.com>
 L:	Eng.Linux@digi.com
 W:	http://www.digi.com
 S:	Orphan
@@ -1884,34 +1629,29 @@ F:	drivers/char/epca*
 F:	drivers/char/digi*
 
 DIRECTORY NOTIFICATION (DNOTIFY)
-P:	Eric Paris
-M:	eparis@parisplace.org
+M:	Eric Paris <eparis@parisplace.org>
 S:	Maintained
 F:	Documentation/filesystems/dnotify.txt
 F:	fs/notify/dnotify/
 F:	include/linux/dnotify.h
 
 DISK GEOMETRY AND PARTITION HANDLING
-P:	Andries Brouwer
-M:	aeb@cwi.nl
+M:	Andries Brouwer <aeb@cwi.nl>
 W:	http://www.win.tue.nl/~aeb/linux/Large-Disk.html
 W:	http://www.win.tue.nl/~aeb/linux/zip/zip-1.html
 W:	http://www.win.tue.nl/~aeb/partitions/partition_types-1.html
 S:	Maintained
 
 DISKQUOTA
-P:	Jan Kara
-M:	jack@suse.cz
+M:	Jan Kara <jack@suse.cz>
 S:	Maintained
 F:	Documentation/filesystems/quota.txt
 F:	fs/quota/
 F:	include/linux/quota*.h
 
 DISTRIBUTED LOCK MANAGER (DLM)
-P:	Christine Caulfield
-M:	ccaulfie@redhat.com
-P:	David Teigland
-M:	teigland@redhat.com
+M:	Christine Caulfield <ccaulfie@redhat.com>
+M:	David Teigland <teigland@redhat.com>
 L:	cluster-devel@redhat.com
 W:	http://sources.redhat.com/cluster/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm.git
@@ -1919,52 +1659,44 @@ S:	Supported
 F:	fs/dlm/
 
 DMA GENERIC OFFLOAD ENGINE SUBSYSTEM
-P:	Maciej Sosnowski
-M:	maciej.sosnowski@intel.com
-P:	Dan Williams
-M:	dan.j.williams@intel.com
+M:	Maciej Sosnowski <maciej.sosnowski@intel.com>
+M:	Dan Williams <dan.j.williams@intel.com>
 S:	Supported
 F:	drivers/dma/
 F:	include/linux/dma*
 
 DME1737 HARDWARE MONITOR DRIVER
-P:	Juerg Haefliger
-M:	juergh@gmail.com
+M:	Juerg Haefliger <juergh@gmail.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/dme1737
 F:	drivers/hwmon/dme1737.c
 
 DOCBOOK FOR DOCUMENTATION
-P:	Randy Dunlap
-M:	rdunlap@xenotime.net
+M:	Randy Dunlap <rdunlap@xenotime.net>
 S:	Maintained
 
 DOCKING STATION DRIVER
-P:	Shaohua Li
-M:	shaohua.li@intel.com
+M:	Shaohua Li <shaohua.li@intel.com>
 L:	linux-acpi@vger.kernel.org
 S:	Supported
 F:	drivers/acpi/dock.c
 
 DOCUMENTATION
-P:	Randy Dunlap
-M:	rdunlap@xenotime.net
+M:	Randy Dunlap <rdunlap@xenotime.net>
 L:	linux-doc@vger.kernel.org
 S:	Maintained
 F:	Documentation/
 
 DOUBLETALK DRIVER
-P:	James R. Van Zandt
-M:	jrv@vanzandt.mv.com
+M:	"James R. Van Zandt" <jrv@vanzandt.mv.com>
 L:	blinux-list@redhat.com
 S:	Maintained
 F:	drivers/char/dtlk.c
 F:	include/linux/dtlk.h
 
 DPT_I2O SCSI RAID DRIVER
-P:	Adaptec OEM Raid Solutions
-M:	aacraid@adaptec.com
+M:	Adaptec OEM Raid Solutions <aacraid@adaptec.com>
 L:	linux-scsi@vger.kernel.org
 W:	http://www.adaptec.com/
 S:	Maintained
@@ -1972,8 +1704,7 @@ F:	drivers/scsi/dpt*
 F:	drivers/scsi/dpt/
 
 DRIVER CORE, KOBJECTS, AND SYSFS
-P:	Greg Kroah-Hartman
-M:	gregkh@suse.de
+M:	Greg Kroah-Hartman <gregkh@suse.de>
 T:	quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/
 S:	Supported
 F:	Documentation/kobject.txt
@@ -1983,52 +1714,45 @@ F:	include/linux/kobj*
 F:	lib/kobj*
 
 DRM DRIVERS
-P:	David Airlie
-M:	airlied@linux.ie
+M:	David Airlie <airlied@linux.ie>
 L:	dri-devel@lists.sourceforge.net
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6.git
 S:	Maintained
 F:	drivers/gpu/drm/
 
 DSCC4 DRIVER
-P:	Francois Romieu
-M:	romieu@fr.zoreil.com
+M:	Francois Romieu <romieu@fr.zoreil.com>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/wan/dscc4.c
 
 DZ DECSTATION DZ11 SERIAL DRIVER
-P:	Maciej W. Rozycki
-M:	macro@linux-mips.org
+M:	"Maciej W. Rozycki" <macro@linux-mips.org>
 S:	Maintained
 F:	drivers/serial/dz.*
 
 EATA-DMA SCSI DRIVER
-P:	Michael Neuffer
-M:	mike@i-Connect.Net
+M:	Michael Neuffer <mike@i-Connect.Net>
 L:	linux-eata@i-connect.net
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/eata*
 
 EATA ISA/EISA/PCI SCSI DRIVER
-P:	Dario Ballabio
-M:	ballabio_dario@emc.com
+M:	Dario Ballabio <ballabio_dario@emc.com>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/eata.c
 
 EATA-PIO SCSI DRIVER
-P:	Michael Neuffer
-M:	mike@i-Connect.Net
+M:	Michael Neuffer <mike@i-Connect.Net>
 L:	linux-eata@i-connect.net
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/eata_pio.*
 
 EBTABLES
-P:	Bart De Schuymer
-M:	bart.de.schuymer@pandora.be
+M:	Bart De Schuymer <bart.de.schuymer@pandora.be>
 L:	ebtables-user@lists.sourceforge.net
 L:	ebtables-devel@lists.sourceforge.net
 W:	http://ebtables.sourceforge.net/
@@ -2037,10 +1761,8 @@ F:	include/linux/netfilter_bridge/ebt_*.h
 F:	net/bridge/netfilter/ebt*.c
 
 ECRYPT FILE SYSTEM
-P:	Tyler Hicks
-M:	tyhicks@linux.vnet.ibm.com
-P:	Dustin Kirkland
-M:	kirkland@canonical.com
+M:	Tyler Hicks <tyhicks@linux.vnet.ibm.com>
+M:	Dustin Kirkland <kirkland@canonical.com>
 L:	ecryptfs-devel@lists.launchpad.net
 W:	https://launchpad.net/ecryptfs
 S:	Supported
@@ -2048,8 +1770,7 @@ F:	Documentation/filesystems/ecryptfs.txt
 F:	fs/ecryptfs/
 
 EDAC-CORE
-P:	Doug Thompson
-M:	dougthompson@xmission.com
+M:	Doug Thompson <dougthompson@xmission.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Supported
@@ -2058,94 +1779,80 @@ F:	drivers/edac/edac_*
 F:	include/linux/edac.h
 
 EDAC-AMD64
-P:	Doug Thompson
-M:	dougthompson@xmission.com
-P:	Borislav Petkov
-M:	borislav.petkov@amd.com
+M:	Doug Thompson <dougthompson@xmission.com>
+M:	Borislav Petkov <borislav.petkov@amd.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Supported
 F:	drivers/edac/amd64_edac*
 
 EDAC-E752X
-P:	Mark Gross
-M:	mark.gross@intel.com
-P:	Doug Thompson
-M:	dougthompson@xmission.com
+M:	Mark Gross <mark.gross@intel.com>
+M:	Doug Thompson <dougthompson@xmission.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Maintained
 F:	drivers/edac/e752x_edac.c
 
 EDAC-E7XXX
-P:	Doug Thompson
-M:	dougthompson@xmission.com
+M:	Doug Thompson <dougthompson@xmission.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Maintained
 F:	drivers/edac/e7xxx_edac.c
 
 EDAC-I82443BXGX
-P:	Tim Small
-M:	tim@buttersideup.com
+M:	Tim Small <tim@buttersideup.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Maintained
 F:	drivers/edac/i82443bxgx_edac.c
 
 EDAC-I3000
-P:	Jason Uhlenkott
-M:	juhlenko@akamai.com
+M:	Jason Uhlenkott <juhlenko@akamai.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Maintained
 F:	drivers/edac/i3000_edac.c
 
 EDAC-I5000
-P:	Doug Thompson
-M:	dougthompson@xmission.com
+M:	Doug Thompson <dougthompson@xmission.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Maintained
 F:	drivers/edac/i5000_edac.c
 
 EDAC-I5400
-P:	Mauro Carvalho Chehab
-M:	mchehab@redhat.com
+M:	Mauro Carvalho Chehab <mchehab@redhat.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Maintained
 F:	drivers/edac/i5400_edac.c
 
 EDAC-I82975X
-P:	Ranganathan Desikan
-M:	ravi@jetztechnologies.com
-P:	Arvind R.
-M:	arvind@jetztechnologies.com
+M:	Ranganathan Desikan <ravi@jetztechnologies.com>
+M:	"Arvind R." <arvind@jetztechnologies.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Maintained
 F:	drivers/edac/i82975x_edac.c
 
 EDAC-PASEMI
-P:	Egor Martovetsky
-M:	egor@pasemi.com
+M:	Egor Martovetsky <egor@pasemi.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Maintained
 F:	drivers/edac/pasemi_edac.c
 
 EDAC-R82600
-P:	Tim Small
-M:	tim@buttersideup.com
+M:	Tim Small <tim@buttersideup.com>
 L:	bluesmoke-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	bluesmoke.sourceforge.net
 S:	Maintained
 F:	drivers/edac/r82600_edac.c
 
 EEEPC LAPTOP EXTRAS DRIVER
-P:	Corentin Chary
-M:	corentincj@iksaif.net
+M:	Corentin Chary <corentincj@iksaif.net>
 L:	acpi4asus-user@lists.sourceforge.net
 W:	http://acpi4asus.sf.net
 S:	Maintained
@@ -2157,65 +1864,53 @@ S:	Orphan
 F:	fs/efs/
 
 EHCA (IBM GX bus InfiniBand adapter) DRIVER
-P:	Hoang-Nam Nguyen
-M:	hnguyen@de.ibm.com
-P:	Christoph Raisch
-M:	raisch@de.ibm.com
+M:	Hoang-Nam Nguyen <hnguyen@de.ibm.com>
+M:	Christoph Raisch <raisch@de.ibm.com>
 L:	general@lists.openfabrics.org
 S:	Supported
 F:	drivers/infiniband/hw/ehca/
 
 EMBEDDED LINUX
-P:	Paul Gortmaker
-M:	paul.gortmaker@windriver.com
-P:	Matt Mackall
-M:	mpm@selenic.com
-P:	David Woodhouse
-M:	dwmw2@infradead.org
+M:	Paul Gortmaker <paul.gortmaker@windriver.com>
+M:	Matt Mackall <mpm@selenic.com>
+M:	David Woodhouse <dwmw2@infradead.org>
 L:	linux-embedded@vger.kernel.org
 S:	Maintained
 
 EMULEX LPFC FC SCSI DRIVER
-P:	James Smart
-M:	james.smart@emulex.com
+M:	James Smart <james.smart@emulex.com>
 L:	linux-scsi@vger.kernel.org
 W:	http://sourceforge.net/projects/lpfcxxxx
 S:	Supported
 F:	drivers/scsi/lpfc/
 
 ENE CB710 FLASH CARD READER DRIVER
-P:	Michał Mirosław
-M:	mirq-linux@rere.qmqm.pl
+M:	Michał Mirosław <mirq-linux@rere.qmqm.pl>
 S:	Maintained
 F:	drivers/misc/cb710/
 F:	drivers/mmc/host/cb710-mmc.*
 F:	include/linux/cb710.h
 
 EPSON 1355 FRAMEBUFFER DRIVER
-P:	Christopher Hoover
-M:	ch@murgatroid.com
-P:	Christopher Hoover
-M:	ch@hpl.hp.com
+M:	Christopher Hoover <ch@murgatroid.com>
+M:	Christopher Hoover <ch@hpl.hp.com>
 S:	Maintained
 F:	drivers/video/epson1355fb.c
 
 EPSON S1D13XXX FRAMEBUFFER DRIVER
-P:	Kristoffer Ericson
-M:	kristoffer.ericson@gmail.com
+M:	Kristoffer Ericson <kristoffer.ericson@gmail.com>
 S:	Maintained
 F:	drivers/video/s1d13xxxfb.c
 F:	include/video/s1d13xxxfb.h
 
 ETHEREXPRESS-16 NETWORK DRIVER
-P:	Philip Blundell
-M:	philb@gnu.org
+M:	Philip Blundell <philb@gnu.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/eexpress.*
 
 ETHERNET BRIDGE
-P:	Stephen Hemminger
-M:	shemminger@linux-foundation.org
+M:	Stephen Hemminger <shemminger@linux-foundation.org>
 L:	bridge@lists.linux-foundation.org
 W:	http://www.linux-foundation.org/en/Net:Bridge
 S:	Maintained
@@ -2223,8 +1918,7 @@ F:	include/linux/netfilter_bridge/
 F:	net/bridge/
 
 ETHERTEAM 16I DRIVER
-P:	Mika Kuoppala
-M:	miku@iki.fi
+M:	Mika Kuoppala <miku@iki.fi>
 S:	Maintained
 F:	drivers/net/eth16i.c
 
@@ -2236,12 +1930,9 @@ F:	fs/ext2/
 F:	include/linux/ext2*
 
 EXT3 FILE SYSTEM
-P:	Stephen Tweedie
-M:	sct@redhat.com
-P:	Andrew Morton
-M:	akpm@linux-foundation.org
-P:	Andreas Dilger
-M:	adilger@sun.com
+M:	Stephen Tweedie <sct@redhat.com>
+M:	Andrew Morton <akpm@linux-foundation.org>
+M:	Andreas Dilger <adilger@sun.com>
 L:	linux-ext4@vger.kernel.org
 S:	Maintained
 F:	Documentation/filesystems/ext3.txt
@@ -2249,10 +1940,8 @@ F:	fs/ext3/
 F:	include/linux/ext3*
 
 EXT4 FILE SYSTEM
-P:	Theodore Ts'o
-M:	tytso@mit.edu
-P:	Andreas Dilger
-M:	adilger@sun.com
+M:	"Theodore Ts'o" <tytso@mit.edu>
+M:	Andreas Dilger <adilger@sun.com>
 L:	linux-ext4@vger.kernel.org
 W:	http://ext4.wiki.kernel.org
 S:	Maintained
@@ -2260,30 +1949,26 @@ F:	Documentation/filesystems/ext4.txt
 F:	fs/ext4/
 
 F71805F HARDWARE MONITORING DRIVER
-P:	Jean Delvare
-M:	khali@linux-fr.org
+M:	Jean Delvare <khali@linux-fr.org>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/f71805f
 F:	drivers/hwmon/f71805f.c
 
 FARSYNC SYNCHRONOUS DRIVER
-P:	Kevin Curtis
-M:	kevin.curtis@farsite.co.uk
+M:	Kevin Curtis <kevin.curtis@farsite.co.uk>
 W:	http://www.farsite.co.uk/
 S:	Supported
 F:	drivers/net/wan/farsync.*
 
 FAULT INJECTION SUPPORT
-P:	Akinobu Mita
-M:	akinobu.mita@gmail.com
+M:	Akinobu Mita <akinobu.mita@gmail.com>
 S:	Supported
 F:	Documentation/fault-injection/
 F:	lib/fault-inject.c
 
 FILE LOCKING (flock() and fcntl()/lockf())
-P:	Matthew Wilcox
-M:	matthew@wil.cx
+M:	Matthew Wilcox <matthew@wil.cx>
 L:	linux-fsdevel@vger.kernel.org
 S:	Maintained
 F:	include/linux/fcntl.h
@@ -2292,25 +1977,21 @@ F:	fs/fcntl.c
 F:	fs/locks.c
 
 FILESYSTEMS (VFS and infrastructure)
-P:	Alexander Viro
-M:	viro@zeniv.linux.org.uk
+M:	Alexander Viro <viro@zeniv.linux.org.uk>
 L:	linux-fsdevel@vger.kernel.org
 S:	Maintained
 F:	fs/*
 
 FINTEK F75375S HARDWARE MONITOR AND FAN CONTROLLER DRIVER
-P:	Riku Voipio
-M:	riku.vipio@iki.fi
+M:	Riku Voipio <riku.vipio@iki.fi>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	drivers/hwmon/f75375s.c
 F:	include/linux/f75375s.h
 
 FIREWIRE SUBSYSTEM
-P:	Kristian Hoegsberg
-M:	krh@redhat.com
-P:	Stefan Richter
-M:	stefanr@s5r6.in-berlin.de
+M:	Kristian Hoegsberg <krh@redhat.com>
+M:	Stefan Richter <stefanr@s5r6.in-berlin.de>
 L:	linux1394-devel@lists.sourceforge.net
 W:	http://www.linux1394.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6.git
@@ -2325,15 +2006,13 @@ F:	drivers/base/firmware*.c
 F:	include/linux/firmware.h
 
 FPU EMULATOR
-P:	Bill Metzenthen
-M:	billm@melbpc.org.au
+M:	Bill Metzenthen <billm@melbpc.org.au>
 W:	http://floatingpoint.sourceforge.net/emulator/index.html
 S:	Maintained
 F:	arch/x86/math-emu/
 
 FRAME RELAY DLCI/FRAD (Sangoma drivers too)
-P:	Mike McLagan
-M:	mike.mclagan@linux.org
+M:	Mike McLagan <mike.mclagan@linux.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/wan/dlci.c
@@ -2348,25 +2027,21 @@ F:	drivers/video/fb*
 F:	include/linux/fb.h
 
 FREESCALE DMA DRIVER
-P:	Li Yang
-M:	leoli@freescale.com
-P:	Zhang Wei
-M:	zw@zh-kernel.org
+M:	Li Yang <leoli@freescale.com>
+M:	Zhang Wei <zw@zh-kernel.org>
 L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 F:	drivers/dma/fsldma.*
 
 FREESCALE I2C CPM DRIVER
-P:	Jochen Friedrich
-M:	jochen@scram.de
+M:	Jochen Friedrich <jochen@scram.de>
 L:	linuxppc-dev@ozlabs.org
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	drivers/i2c/busses/i2c-cpm.c
 
 FREESCALE IMX / MXC FRAMEBUFFER DRIVER
-P:	Sascha Hauer
-M:	kernel@pengutronix.de
+M:	Sascha Hauer <kernel@pengutronix.de>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
@@ -2374,10 +2049,8 @@ F:	arch/arm/plat-mxc/include/mach/imxfb.h
 F:	drivers/video/imxfb.c
 
 FREESCALE SOC FS_ENET DRIVER
-P:	Pantelis Antoniou
-M:	pantelis.antoniou@gmail.com
-P:	Vitaly Bordug
-M:	vbordug@ru.mvista.com
+M:	Pantelis Antoniou <pantelis.antoniou@gmail.com>
+M:	Vitaly Bordug <vbordug@ru.mvista.com>
 L:	linuxppc-dev@ozlabs.org
 L:	netdev@vger.kernel.org
 S:	Maintained
@@ -2385,39 +2058,34 @@ F:	drivers/net/fs_enet/
 F:	include/linux/fs_enet_pd.h
 
 FREESCALE QUICC ENGINE LIBRARY
-P:	Timur Tabi
-M:	timur@freescale.com
+M:	Timur Tabi <timur@freescale.com>
 L:	linuxppc-dev@ozlabs.org
 S:	Supported
 F:	arch/powerpc/sysdev/qe_lib/
 F:	arch/powerpc/include/asm/*qe.h
 
 FREESCALE HIGHSPEED USB DEVICE DRIVER
-P:	Li Yang
-M:	leoli@freescale.com
+M:	Li Yang <leoli@freescale.com>
 L:	linux-usb@vger.kernel.org
 L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 F:	drivers/usb/gadget/fsl_usb2_udc.c
 
 FREESCALE QUICC ENGINE UCC ETHERNET DRIVER
-P:	Li Yang
-M:	leoli@freescale.com
+M:	Li Yang <leoli@freescale.com>
 L:	netdev@vger.kernel.org
 L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 F:	drivers/net/ucc_geth*
 
 FREESCALE QUICC ENGINE UCC UART DRIVER
-P:	Timur Tabi
-M:	timur@freescale.com
+M:	Timur Tabi <timur@freescale.com>
 L:	linuxppc-dev@ozlabs.org
 S:	Supported
 F:	drivers/serial/ucc_uart.c
 
 FREESCALE SOC SOUND DRIVERS
-P:	Timur Tabi
-M:	timur@freescale.com
+M:	Timur Tabi <timur@freescale.com>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 L:	linuxppc-dev@ozlabs.org
 S:	Supported
@@ -2425,17 +2093,14 @@ F:	sound/soc/fsl/fsl*
 F:	sound/soc/fsl/mpc8610_hpcd.c
 
 FREEVXFS FILESYSTEM
-P:	Christoph Hellwig
-M:	hch@infradead.org
+M:	Christoph Hellwig <hch@infradead.org>
 W:	ftp://ftp.openlinux.org/pub/people/hch/vxfs
 S:	Maintained
 F:	fs/freevxfs/
 
 FREEZER
-P:	Pavel Machek
-M:	pavel@ucw.cz
-P:	Rafael J. Wysocki
-M:	rjw@sisk.pl
+M:	Pavel Machek <pavel@ucw.cz>
+M:	"Rafael J. Wysocki" <rjw@sisk.pl>
 L:	linux-pm@lists.linux-foundation.org
 S:	Supported
 F:	Documentation/power/freezing-of-tasks.txt
@@ -2443,8 +2108,7 @@ F:	include/linux/freezer.h
 F:	kernel/freezer.c
 
 FS-CACHE: LOCAL CACHING FOR NETWORK FILESYSTEMS
-P:	David Howells
-M:	dhowells@redhat.com
+M:	David Howells <dhowells@redhat.com>
 L:	linux-cachefs@redhat.com
 S:	Supported
 F:	Documentation/filesystems/caching/
@@ -2452,8 +2116,7 @@ F:	fs/fscache/
 F:	include/linux/fscache*.h
 
 FTRACE
-P:	Steven Rostedt
-M:	rostedt@goodmis.org
+M:	Steven Rostedt <rostedt@goodmis.org>
 S:	Maintained
 F:	Documentation/trace/ftrace.txt
 F:	arch/*/*/*/ftrace.h
@@ -2462,21 +2125,18 @@ F:	include/*/ftrace.h
 F:	kernel/trace/
 
 FUJITSU FR-V (FRV) PORT
-P:	David Howells
-M:	dhowells@redhat.com
+M:	David Howells <dhowells@redhat.com>
 S:	Maintained
 F:	arch/frv/
 
 FUJITSU LAPTOP EXTRAS
-P:	Jonathan Woithe
-M:	jwoithe@physics.adelaide.edu.au
+M:	Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
 L:	linux-acpi@vger.kernel.org
 S:	Maintained
 F:	drivers/platform/x86/fujitsu-laptop.c
 
 FUSE: FILESYSTEM IN USERSPACE
-P:	Miklos Szeredi
-M:	miklos@szeredi.hu
+M:	Miklos Szeredi <miklos@szeredi.hu>
 L:	fuse-devel@lists.sourceforge.net
 W:	http://fuse.sourceforge.net/
 S:	Maintained
@@ -2484,30 +2144,26 @@ F:	fs/fuse/
 F:	include/linux/fuse.h
 
 FUTURE DOMAIN TMC-16x0 SCSI DRIVER (16-bit)
-P:	Rik Faith
-M:	faith@cs.unc.edu
+M:	Rik Faith <faith@cs.unc.edu>
 L:	linux-scsi@vger.kernel.org
 S:	Odd Fixes (e.g., new signatures)
 F:	drivers/scsi/fdomain.*
 
 GDT SCSI DISK ARRAY CONTROLLER DRIVER
-P:	Achim Leubner
-M:	achim_leubner@adaptec.com
+M:	Achim Leubner <achim_leubner@adaptec.com>
 L:	linux-scsi@vger.kernel.org
 W:	http://www.icp-vortex.com/
 S:	Supported
 F:	drivers/scsi/gdt*
 
 GENERIC GPIO I2C DRIVER
-P:	Haavard Skinnemoen
-M:	hskinnemoen@atmel.com
+M:	Haavard Skinnemoen <hskinnemoen@atmel.com>
 S:	Supported
 F:	drivers/i2c/busses/i2c-gpio.c
 F:	include/linux/i2c-gpio.h
 
 GENERIC HDLC (WAN) DRIVERS
-P:	Krzysztof Halasa
-M:	khc@pm.waw.pl
+M:	Krzysztof Halasa <khc@pm.waw.pl>
 W:	http://www.kernel.org/pub/linux/utils/net/hdlc/
 S:	Maintained
 F:	drivers/net/wan/c101.c
@@ -2519,16 +2175,14 @@ F:	drivers/net/wan/pci200syn.c
 F:	drivers/net/wan/wanxl*
 
 GENERIC INCLUDE/ASM HEADER FILES
-P:	Arnd Bergmann
-M:	arnd@arndb.de
+M:	Arnd Bergmann <arnd@arndb.de>
 L:	linux-arch@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic.git
 S:	Maintained
 F:	include/asm-generic
 
 GFS2 FILE SYSTEM
-P:	Steven Whitehouse
-M:	swhiteho@redhat.com
+M:	Steven Whitehouse <swhiteho@redhat.com>
 L:	cluster-devel@redhat.com
 W:	http://sources.redhat.com/cluster/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes.git
@@ -2539,10 +2193,8 @@ F:	fs/gfs2/
 F:	include/linux/gfs2_ondisk.h
 
 GIGASET ISDN DRIVERS
-P:	Hansjoerg Lipp
-M:	hjlipp@web.de
-P:	Tilman Schmidt
-M:	tilman@imap.cc
+M:	Hansjoerg Lipp <hjlipp@web.de>
+M:	Tilman Schmidt <tilman@imap.cc>
 L:	gigaset307x-common@lists.sourceforge.net
 W:	http://gigaset307x.sourceforge.net/
 S:	Maintained
@@ -2551,8 +2203,7 @@ F:	drivers/isdn/gigaset/
 F:	include/linux/gigaset_dev.h
 
 HARD DRIVE ACTIVE PROTECTION SYSTEM (HDAPS) DRIVER
-P:	Frank Seidel
-M:	frank@f-seidel.de
+M:	Frank Seidel <frank@f-seidel.de>
 L:	lm-sensors@lm-sensors.org
 W:	http://www.kernel.org/pub/linux/kernel/people/fseidel/hdaps/
 S:	Maintained
@@ -2564,40 +2215,35 @@ S:	Odd Fixes
 F:	drivers/char/hvc_*
 
 GSPCA FINEPIX SUBDRIVER
-P:	Frank Zago
-M:	frank@zago.net
+M:	Frank Zago <frank@zago.net>
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 S:	Maintained
 F:	drivers/media/video/gspca/finepix.c
 
 GSPCA M5602 SUBDRIVER
-P:	Erik Andren
-M:	erik.andren@gmail.com
+M:	Erik Andren <erik.andren@gmail.com>
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 S:	Maintained
 F:	drivers/media/video/gspca/m5602/
 
 GSPCA PAC207 SONIXB SUBDRIVER
-P:	Hans de Goede
-M:	hdegoede@redhat.com
+M:	Hans de Goede <hdegoede@redhat.com>
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 S:	Maintained
 F:	drivers/media/video/gspca/pac207.c
 
 GSPCA T613 SUBDRIVER
-P:	Leandro Costantino
-M:	lcostantino@gmail.com
+M:	Leandro Costantino <lcostantino@gmail.com>
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 S:	Maintained
 F:	drivers/media/video/gspca/t613.c
 
 GSPCA USB WEBCAM DRIVER
-P:	Jean-Francois Moine
-M:	moinejf@free.fr
+M:	Jean-Francois Moine <moinejf@free.fr>
 W:	http://moinejf.free.fr
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
@@ -2617,31 +2263,27 @@ F:	drivers/char/hw_random/
 F:	include/linux/hw_random.h
 
 HARMONY SOUND DRIVER
-P:	Kyle McMartin
-M:	kyle@mcmartin.ca
+M:	Kyle McMartin <kyle@mcmartin.ca>
 L:	linux-parisc@vger.kernel.org
 S:	Maintained
 F:	sound/parisc/harmony.*
 
 HAYES ESP SERIAL DRIVER
-P:	Andrew J. Robinson
-M:	arobinso@nyx.net
+M:	"Andrew J. Robinson" <arobinso@nyx.net>
 W:	http://www.nyx.net/~arobinso
 S:	Maintained
 F:	Documentation/serial/hayes-esp.txt
 F:	drivers/char/esp.c
 
 HEWLETT-PACKARD SMART2 RAID DRIVER
-P:	Chirag Kantharia
-M:	chirag.kantharia@hp.com
+M:	Chirag Kantharia <chirag.kantharia@hp.com>
 L:	iss_storagedev@hp.com
 S:	Maintained
 F:	Documentation/blockdev/cpqarray.txt
 F:	drivers/block/cpqarray.*
 
 HEWLETT-PACKARD SMART CISS RAID DRIVER (cciss)
-P:	Mike Miller
-M:	mike.miller@hp.com
+M:	Mike Miller <mike.miller@hp.com>
 L:	iss_storagedev@hp.com
 S:	Supported
 F:	Documentation/blockdev/cciss.txt
@@ -2649,25 +2291,21 @@ F:	drivers/block/cciss*
 F:	include/linux/cciss_ioctl.h
 
 HFS FILESYSTEM
-P:	Roman Zippel
-M:	zippel@linux-m68k.org
+M:	Roman Zippel <zippel@linux-m68k.org>
 S:	Maintained
 F:	Documentation/filesystems/hfs.txt
 F:	fs/hfs/
 
 HGA FRAMEBUFFER DRIVER
-P:	Ferenc Bakonyi
-M:	fero@drama.obuda.kando.hu
+M:	Ferenc Bakonyi <fero@drama.obuda.kando.hu>
 L:	linux-nvidia@lists.surfsouth.com
 W:	http://drama.obuda.kando.hu/~fero/cgi-bin/hgafb.shtml
 S:	Maintained
 F:	drivers/video/hgafb.c
 
 HIBERNATION (aka Software Suspend, aka swsusp)
-P:	Pavel Machek
-M:	pavel@ucw.cz
-P:	Rafael J. Wysocki
-M:	rjw@sisk.pl
+M:	Pavel Machek <pavel@ucw.cz>
+M:	"Rafael J. Wysocki" <rjw@sisk.pl>
 L:	linux-pm@lists.linux-foundation.org
 S:	Supported
 F:	arch/x86/power/
@@ -2679,8 +2317,7 @@ F:	include/linux/pm.h
 F:	arch/*/include/asm/suspend*.h
 
 HID CORE LAYER
-P:	Jiri Kosina
-M:	jkosina@suse.cz
+M:	Jiri Kosina <jkosina@suse.cz>
 L:	linux-input@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid.git
 S:	Maintained
@@ -2688,16 +2325,14 @@ F:	drivers/hid/
 F:	include/linux/hid*
 
 HIGH-RESOLUTION TIMERS, CLOCKEVENTS, DYNTICKS
-P:	Thomas Gleixner
-M:	tglx@linutronix.de
+M:	Thomas Gleixner <tglx@linutronix.de>
 S:	Maintained
 F:	Documentation/timers/
 F:	kernel/hrtimer.c
 F:	include/linux/hrtimer.h
 
 HIGH-SPEED SCC DRIVER FOR AX.25
-P:	Klaus Kudielka
-M:	klaus.kudielka@ieee.org
+M:	Klaus Kudielka <klaus.kudielka@ieee.org>
 L:	linux-hams@vger.kernel.org
 W:	http://www.nt.tuwien.ac.at/~kkudielk/Linux/
 S:	Maintained
@@ -2705,16 +2340,14 @@ F:	drivers/net/hamradio/dmascc.c
 F:	drivers/net/hamradio/scc.c
 
 HIGHPOINT ROCKETRAID 3xxx RAID DRIVER
-P:	HighPoint Linux Team
-M:	linux@highpoint-tech.com
+M:	HighPoint Linux Team <linux@highpoint-tech.com>
 W:	http://www.highpoint-tech.com
 S:	Supported
 F:	Documentation/scsi/hptiop.txt
 F:	drivers/scsi/hptiop.c
 
 HIPPI
-P:	Jes Sorensen
-M:	jes@trained-monkey.org
+M:	Jes Sorensen <jes@trained-monkey.org>
 L:	linux-hippi@sunsite.dk
 S:	Maintained
 F:	include/linux/hippidevice.h
@@ -2722,8 +2355,7 @@ F:	include/linux/if_hippi.h
 F:	net/802/hippi.c
 
 HOST AP DRIVER
-P:	Jouni Malinen
-M:	j@w1.fi
+M:	Jouni Malinen <j@w1.fi>
 L:	hostap@shmoo.com (subscribers-only)
 L:	linux-wireless@vger.kernel.org
 W:	http://hostap.epitest.fi/
@@ -2731,82 +2363,69 @@ S:	Maintained
 F:	drivers/net/wireless/hostap/
 
 HP COMPAQ TC1100 TABLET WMI EXTRAS DRIVER
-P:	Carlos Corbacho
-M:	carlos@strangeworlds.co.uk
+M:	Carlos Corbacho <carlos@strangeworlds.co.uk>
 S:	Odd Fixes
 F:	drivers/platform/x86/tc1100-wmi.c
 
 HP100:	Driver for HP 10/100 Mbit/s Voice Grade Network Adapter Series
-P:	Jaroslav Kysela
-M:	perex@perex.cz
+M:	Jaroslav Kysela <perex@perex.cz>
 S:	Maintained
 F:	drivers/net/hp100.*
 
 HPET:	High Precision Event Timers driver
-P:	Clemens Ladisch
-M:	clemens@ladisch.de
+M:	Clemens Ladisch <clemens@ladisch.de>
 S:	Maintained
 F:	Documentation/timers/hpet.txt
 F:	drivers/char/hpet.c
 F:	include/linux/hpet.h
 
 HPET:	i386
-P:	Venkatesh Pallipadi (Venki)
-M:	venkatesh.pallipadi@intel.com
+M:	"Venkatesh Pallipadi (Venki)" <venkatesh.pallipadi@intel.com>
 S:	Maintained
 F:	arch/x86/kernel/hpet.c
 F:	arch/x86/include/asm/hpet.h
 
 HPET:	x86_64
-P:	Vojtech Pavlik
-M:	vojtech@suse.cz
+M:	Vojtech Pavlik <vojtech@suse.cz>
 S:	Maintained
 
 HPET:	ACPI
-P:	Bob Picco
-M:	bob.picco@hp.com
+M:	Bob Picco <bob.picco@hp.com>
 S:	Maintained
 F:	drivers/char/hpet.c
 
 HPFS FILESYSTEM
-P:	Mikulas Patocka
-M:	mikulas@artax.karlin.mff.cuni.cz
+M:	Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
 W:	http://artax.karlin.mff.cuni.cz/~mikulas/vyplody/hpfs/index-e.cgi
 S:	Maintained
 F:	fs/hpfs/
 
 HSO 3G MODEM DRIVER
-P:	Jan Dumon
-M:	j.dumon@option.com
+M:	Jan Dumon <j.dumon@option.com>
 W:	http://www.pharscape.org
 S:	Maintained
 F:	drivers/net/usb/hso.c
 
 HTCPEN TOUCHSCREEN DRIVER
-P:	Pau Oliva Fora
-M:	pof@eslack.org
+M:	Pau Oliva Fora <pof@eslack.org>
 L:	linux-input@vger.kernel.org
 S:	Maintained
 F:	drivers/input/touchscreen/htcpen.c
 
 HUGETLB FILESYSTEM
-P:	William Irwin
-M:	wli@holomorphy.com
+M:	William Irwin <wli@holomorphy.com>
 S:	Maintained
 F:	fs/hugetlbfs/
 
 I2C/SMBUS STUB DRIVER
-P:	Mark M. Hoffman
-M:	mhoffman@lightlink.com
+M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	drivers/i2c/busses/i2c-stub.c
 
 I2C SUBSYSTEM
-P:	Jean Delvare (PC drivers, core)
-M:	khali@linux-fr.org
-P:	Ben Dooks (embedded platforms)
-M:	ben-linux@fluff.org
+M:	"Jean Delvare (PC drivers, core)" <khali@linux-fr.org>
+M:	"Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
 L:	linux-i2c@vger.kernel.org
 W:	http://i2c.wiki.kernel.org/
 T:	quilt kernel.org/pub/linux/kernel/people/jdelvare/linux-2.6/jdelvare-i2c/
@@ -2818,30 +2437,25 @@ F:	include/linux/i2c-dev.h
 F:	include/linux/i2c-id.h
 
 I2C-TINY-USB DRIVER
-P:	Till Harbaum
-M:	till@harbaum.org
+M:	Till Harbaum <till@harbaum.org>
 L:	linux-i2c@vger.kernel.org
 W:	http://www.harbaum.org/till/i2c_tiny_usb
 S:	Maintained
 F:	drivers/i2c/busses/i2c-tiny-usb.c
 
 i386 BOOT CODE
-P:	H. Peter Anvin
-M:	hpa@zytor.com
+M:	"H. Peter Anvin" <hpa@zytor.com>
 S:	Maintained
 F:	arch/x86/boot/
 
 i386 SETUP CODE / CPU ERRATA WORKAROUNDS
-P:	H. Peter Anvin
-M:	hpa@zytor.com
+M:	"H. Peter Anvin" <hpa@zytor.com>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup.git
 S:	Maintained
 
 IA64 (Itanium) PLATFORM
-P:	Tony Luck
-M:	tony.luck@intel.com
-P:	Fenghua Yu
-M:	fenghua.yu@intel.com
+M:	Tony Luck <tony.luck@intel.com>
+M:	Fenghua Yu <fenghua.yu@intel.com>
 L:	linux-ia64@vger.kernel.org
 W:	http://www.ia64-linux.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6.git
@@ -2849,29 +2463,25 @@ S:	Maintained
 F:	arch/ia64/
 
 IBM MCA SCSI SUBSYSTEM DRIVER
-P:	Michael Lang
-M:	langa2@kph.uni-mainz.de
+M:	Michael Lang <langa2@kph.uni-mainz.de>
 W:	http://www.uni-mainz.de/~langm000/linux.html
 S:	Maintained
 F:	drivers/scsi/ibmmca.c
 
 IBM Power Linux RAID adapter
-P:	Brian King
-M:	brking@us.ibm.com
+M:	Brian King <brking@us.ibm.com>
 S:	Supported
 F:	drivers/scsi/ipr.*
 
 IBM ServeRAID RAID DRIVER
 P:	Jack Hammer
-P:	Dave Jeffery
-M:	ipslinux@adaptec.com
+M:	Dave Jeffery <ipslinux@adaptec.com>
 W:	http://www.developer.ibm.com/welcome/netfinity/serveraid.html
 S:	Supported
 F:	drivers/scsi/ips.*
 
 IDE SUBSYSTEM
-P:	David S. Miller
-M:	davem@davemloft.net
+M:	"David S. Miller" <davem@davemloft.net>
 L:	linux-ide@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6.git
 S:	Maintained
@@ -2880,25 +2490,21 @@ F:	drivers/ide/
 F:	include/linux/ide.h
 
 IDE/ATAPI DRIVERS
-P:	Borislav Petkov
-M:	petkovbb@gmail.com
+M:	Borislav Petkov <petkovbb@gmail.com>
 L:	linux-ide@vger.kernel.org
 S:	Maintained
 F:	Documentation/cdrom/ide-cd
 F:	drivers/ide/ide-cd*
 
 IDLE-I7300
-P:	Andy Henroid
-M:	andrew.d.henroid@intel.com
+M:	Andy Henroid <andrew.d.henroid@intel.com>
 L:	linux-pm@lists.linux-foundation.org
 S:	Supported
 F:	drivers/idle/i7300_idle.c
 
 IEEE 1394 SUBSYSTEM
-P:	Ben Collins
-M:	ben.collins@ubuntu.com
-P:	Stefan Richter
-M:	stefanr@s5r6.in-berlin.de
+M:	Ben Collins <ben.collins@ubuntu.com>
+M:	Stefan Richter <stefanr@s5r6.in-berlin.de>
 L:	linux1394-devel@lists.sourceforge.net
 W:	http://www.linux1394.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6.git
@@ -2906,19 +2512,15 @@ S:	Maintained
 F:	drivers/ieee1394/
 
 IEEE 1394 RAW I/O DRIVER
-P:	Dan Dennedy
-M:	dan@dennedy.org
-P:	Stefan Richter
-M:	stefanr@s5r6.in-berlin.de
+M:	Dan Dennedy <dan@dennedy.org>
+M:	Stefan Richter <stefanr@s5r6.in-berlin.de>
 L:	linux1394-devel@lists.sourceforge.net
 S:	Maintained
 F:	drivers/ieee1394/raw1394*
 
 IEEE 802.15.4 SUBSYSTEM
-P:	Dmitry Eremin-Solenikov
-M:	dbaryshkov@gmail.com
-P:	Sergey Lapin
-M:	slapin@ossfans.org
+M:	Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
+M:	Sergey Lapin <slapin@ossfans.org>
 L:	linux-zigbee-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	http://apps.sourceforge.net/trac/linux-zigbee
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/lowpan/lowpan.git
@@ -2927,8 +2529,7 @@ F:	net/ieee802154/
 F:	drivers/ieee802154/
 
 INTEGRITY MEASUREMENT ARCHITECTURE (IMA)
-P:	Mimi Zohar
-M:	zohar@us.ibm.com
+M:	Mimi Zohar <zohar@us.ibm.com>
 S:	Supported
 F:	security/integrity/ima/
 
@@ -2938,12 +2539,9 @@ S:	Orphan
 F:	drivers/video/imsttfb.c
 
 INFINIBAND SUBSYSTEM
-P:	Roland Dreier
-M:	rolandd@cisco.com
-P:	Sean Hefty
-M:	sean.hefty@intel.com
-P:	Hal Rosenstock
-M:	hal.rosenstock@gmail.com
+M:	Roland Dreier <rolandd@cisco.com>
+M:	Sean Hefty <sean.hefty@intel.com>
+M:	Hal Rosenstock <hal.rosenstock@gmail.com>
 L:	general@lists.openfabrics.org (moderated for non-subscribers)
 W:	http://www.openib.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband.git
@@ -2953,66 +2551,55 @@ F:	drivers/infiniband/
 F:	include/linux/if_infiniband.h
 
 INOTIFY
-P:	John McCutchan
-M:	john@johnmccutchan.com
-P:	Robert Love
-M:	rlove@rlove.org
-P:	Eric Paris
-M:	eparis@parisplace.org
+M:	John McCutchan <john@johnmccutchan.com>
+M:	Robert Love <rlove@rlove.org>
+M:	Eric Paris <eparis@parisplace.org>
 S:	Maintained
 F:	Documentation/filesystems/inotify.txt
 F:	fs/notify/inotify/
 F:	include/linux/inotify.h
 
 INPUT (KEYBOARD, MOUSE, JOYSTICK, TOUCHSCREEN) DRIVERS
-P:	Dmitry Torokhov
-M:	dmitry.torokhov@gmail.com
-P:	Dmitry Torokhov
-M:	dtor@mail.ru
+M:	Dmitry Torokhov <dmitry.torokhov@gmail.com>
+M:	Dmitry Torokhov <dtor@mail.ru>
 L:	linux-input@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input.git
 S:	Maintained
 F:	drivers/input/
 
 INTEL FRAMEBUFFER DRIVER (excluding 810 and 815)
-P:	Sylvain Meyer
-M:	sylvain.meyer@worldonline.fr
+M:	Sylvain Meyer <sylvain.meyer@worldonline.fr>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 F:	Documentation/fb/intelfb.txt
 F:	drivers/video/intelfb/
 
 INTEL 810/815 FRAMEBUFFER DRIVER
-P:	Antonino Daplas
-M:	adaplas@gmail.com
+M:	Antonino Daplas <adaplas@gmail.com>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/video/i810/
 
 INTEL MENLOW THERMAL DRIVER
-P:	Sujith Thomas
-M:	sujith.thomas@intel.com
+M:	Sujith Thomas <sujith.thomas@intel.com>
 L:	linux-acpi@vger.kernel.org
 W:	http://www.lesswatts.org/projects/acpi/
 S:	Supported
 F:	drivers/platform/x86/intel_menlow.c
 
 INTEL IA32 MICROCODE UPDATE SUPPORT
-P:	Tigran Aivazian
-M:	tigran@aivazian.fsnet.co.uk
+M:	Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
 S:	Maintained
 F:	arch/x86/kernel/microcode_core.c
 F:	arch/x86/kernel/microcode_intel.c
 
 INTEL I/OAT DMA DRIVER
-P:	Maciej Sosnowski
-M:	maciej.sosnowski@intel.com
+M:	Maciej Sosnowski <maciej.sosnowski@intel.com>
 S:	Supported
 F:	drivers/dma/ioat*
 
 INTEL IOMMU (VT-d)
-P:	David Woodhouse
-M:	dwmw2@infradead.org
+M:	David Woodhouse <dwmw2@infradead.org>
 L:	iommu@lists.linux-foundation.org
 T:	git git://git.infradead.org/iommu-2.6.git
 S:	Supported
@@ -3020,14 +2607,12 @@ F:	drivers/pci/intel-iommu.c
 F:	include/linux/intel-iommu.h
 
 INTEL IOP-ADMA DMA DRIVER
-P:	Dan Williams
-M:	dan.j.williams@intel.com
+M:	Dan Williams <dan.j.williams@intel.com>
 S:	Supported
 F:	drivers/dma/iop-adma.c
 
 INTEL IXP4XX QMGR, NPE, ETHERNET and HSS SUPPORT
-P:	Krzysztof Halasa
-M:	khc@pm.waw.pl
+M:	Krzysztof Halasa <khc@pm.waw.pl>
 S:	Maintained
 F:	arch/arm/mach-ixp4xx/include/mach/qmgr.h
 F:	arch/arm/mach-ixp4xx/include/mach/npe.h
@@ -3037,29 +2622,22 @@ F:	drivers/net/arm/ixp4xx_eth.c
 F:	drivers/net/wan/ixp4xx_hss.c
 
 INTEL IXP4XX RANDOM NUMBER GENERATOR SUPPORT
-P:	Deepak Saxena
-M:	dsaxena@plexity.net
+M:	Deepak Saxena <dsaxena@plexity.net>
 S:	Maintained
 F:	drivers/char/hw_random/ixp4xx-rng.c
 
 INTEL IXP2000 ETHERNET DRIVER
-P:	Lennert Buytenhek
-M:	kernel@wantstofly.org
+M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/ixp2000/
 
 INTEL ETHERNET DRIVERS (e100/e1000/e1000e/igb/ixgb/ixgbe)
-P:	Jeff Kirsher
-M:	jeffrey.t.kirsher@intel.com
-P:	Jesse Brandeburg
-M:	jesse.brandeburg@intel.com
-P:	Bruce Allan
-M:	bruce.w.allan@intel.com
-P:	PJ Waskiewicz
-M:	peter.p.waskiewicz.jr@intel.com
-P:	John Ronciak
-M:	john.ronciak@intel.com
+M:	Jeff Kirsher <jeffrey.t.kirsher@intel.com>
+M:	Jesse Brandeburg <jesse.brandeburg@intel.com>
+M:	Bruce Allan <bruce.w.allan@intel.com>
+M:	PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
+M:	John Ronciak <john.ronciak@intel.com>
 L:	e1000-devel@lists.sourceforge.net
 W:	http://e1000.sourceforge.net/
 S:	Supported
@@ -3071,12 +2649,9 @@ F:	drivers/net/ixgb/
 F:	drivers/net/ixgbe/
 
 INTEL PRO/WIRELESS 2100 NETWORK CONNECTION SUPPORT
-P:	Zhu Yi
-M:	yi.zhu@intel.com
-P:	James Ketrenos
-M:	jketreno@linux.intel.com
-P:	Reinette Chatre
-M:	reinette.chatre@intel.com
+M:	Zhu Yi <yi.zhu@intel.com>
+M:	James Ketrenos <jketreno@linux.intel.com>
+M:	Reinette Chatre <reinette.chatre@intel.com>
 L:	linux-wireless@vger.kernel.org
 L:	ipw2100-devel@lists.sourceforge.net
 W:	http://lists.sourceforge.net/mailman/listinfo/ipw2100-devel
@@ -3086,12 +2661,9 @@ F:	Documentation/networking/README.ipw2100
 F:	drivers/net/wireless/ipw2x00/ipw2100.*
 
 INTEL PRO/WIRELESS 2915ABG NETWORK CONNECTION SUPPORT
-P:	Zhu Yi
-M:	yi.zhu@intel.com
-P:	James Ketrenos
-M:	jketreno@linux.intel.com
-P:	Reinette Chatre
-M:	reinette.chatre@intel.com
+M:	Zhu Yi <yi.zhu@intel.com>
+M:	James Ketrenos <jketreno@linux.intel.com>
+M:	Reinette Chatre <reinette.chatre@intel.com>
 L:	linux-wireless@vger.kernel.org
 L:	ipw2100-devel@lists.sourceforge.net
 W:	http://lists.sourceforge.net/mailman/listinfo/ipw2100-devel
@@ -3101,8 +2673,7 @@ F:	Documentation/networking/README.ipw2200
 F:	drivers/net/wireless/ipw2x00/ipw2200.*
 
 INTEL WIRELESS WIMAX CONNECTION 2400
-P:	Inaky Perez-Gonzalez
-M:	inaky.perez-gonzalez@intel.com
+M:	Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
 M:	linux-wimax@intel.com
 L:	wimax@linuxwimax.org
 S:	Supported
@@ -3112,10 +2683,8 @@ F:	drivers/net/wimax/i2400m/
 F:	include/linux/wimax/i2400m.h
 
 INTEL WIRELESS WIFI LINK (iwlwifi)
-P:	Zhu Yi
-M:	yi.zhu@intel.com
-P:	Reinette Chatre
-M:	reinette.chatre@intel.com
+M:	Zhu Yi <yi.zhu@intel.com>
+M:	Reinette Chatre <reinette.chatre@intel.com>
 L:	linux-wireless@vger.kernel.org
 L:	ipw3945-devel@lists.sourceforge.net
 W:	http://intellinuxwireless.org
@@ -3124,47 +2693,39 @@ S:	Supported
 F:	drivers/net/wireless/iwlwifi/
 
 IOC3 ETHERNET DRIVER
-P:	Ralf Baechle
-M:	ralf@linux-mips.org
+M:	Ralf Baechle <ralf@linux-mips.org>
 L:	linux-mips@linux-mips.org
 S:	Maintained
 F:	drivers/net/ioc3-eth.c
 
 IOC3 SERIAL DRIVER
-P:	Pat Gefre
-M:	pfg@sgi.com
+M:	Pat Gefre <pfg@sgi.com>
 L:	linux-mips@linux-mips.org
 S:	Maintained
 F:	drivers/serial/ioc3_serial.c
 
 IP MASQUERADING
-P:	Juanjo Ciarlante
-M:	jjciarla@raiz.uncu.edu.ar
+M:	Juanjo Ciarlante <jjciarla@raiz.uncu.edu.ar>
 S:	Maintained
 F:	net/ipv4/netfilter/ipt_MASQUERADE.c
 
 IP1000A 10/100/1000 GIGABIT ETHERNET DRIVER
-P:	Francois Romieu
-M:	romieu@fr.zoreil.com
-P:	Sorbica Shieh
-M:	sorbica@icplus.com.tw
-P:	Jesse Huang
-M:	jesse@icplus.com.tw
+M:	Francois Romieu <romieu@fr.zoreil.com>
+M:	Sorbica Shieh <sorbica@icplus.com.tw>
+M:	Jesse Huang <jesse@icplus.com.tw>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/ipg.c
 
 IPATH DRIVER
-P:	Ralph Campbell
-M:	infinipath@qlogic.com
+M:	Ralph Campbell <infinipath@qlogic.com>
 L:	general@lists.openfabrics.org
 T:	git git://git.qlogic.com/ipath-linux-2.6
 S:	Supported
 F:	drivers/infiniband/hw/ipath/
 
 IPMI SUBSYSTEM
-P:	Corey Minyard
-M:	minyard@acm.org
+M:	Corey Minyard <minyard@acm.org>
 L:	openipmi-developer@lists.sourceforge.net
 W:	http://openipmi.sourceforge.net/
 S:	Supported
@@ -3173,20 +2734,16 @@ F:	drivers/char/ipmi/
 F:	include/linux/ipmi*
 
 IPS SCSI RAID DRIVER
-P:	Adaptec OEM Raid Solutions
-M:	aacraid@adaptec.com
+M:	Adaptec OEM Raid Solutions <aacraid@adaptec.com>
 L:	linux-scsi@vger.kernel.org
 W:	http://www.adaptec.com/
 S:	Maintained
 F:	drivers/scsi/ips*
 
 IPVS
-P:	Wensong Zhang
-M:	wensong@linux-vs.org
-P:	Simon Horman
-M:	horms@verge.net.au
-P:	Julian Anastasov
-M:	ja@ssi.bg
+M:	Wensong Zhang <wensong@linux-vs.org>
+M:	Simon Horman <horms@verge.net.au>
+M:	Julian Anastasov <ja@ssi.bg>
 L:	netdev@vger.kernel.org
 L:	lvs-devel@vger.kernel.org
 S:	Maintained
@@ -3194,17 +2751,14 @@ F:	Documentation/networking/ipvs-sysctl.txt
 F:	net/netfilter/ipvs/
 
 IPWIRELESS DRIVER
-P:	Jiri Kosina
-M:	jkosina@suse.cz
-P:	David Sterba
-M:	dsterba@suse.cz
+M:	Jiri Kosina <jkosina@suse.cz>
+M:	David Sterba <dsterba@suse.cz>
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/ipwireless_cs.git
 F:	drivers/char/pcmcia/ipwireless/
 
 IPX NETWORK LAYER
-P:	Arnaldo Carvalho de Melo
-M:	acme@ghostprotocols.net
+M:	Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	include/linux/ipx.h
@@ -3212,8 +2766,7 @@ F:	include/net/ipx.h
 F:	net/ipx/
 
 IRDA SUBSYSTEM
-P:	Samuel Ortiz
-M:	samuel@sortiz.org
+M:	Samuel Ortiz <samuel@sortiz.org>
 L:	irda-users@lists.sourceforge.net (subscribers-only)
 W:	http://irda.sourceforge.net/
 S:	Maintained
@@ -3224,16 +2777,14 @@ F:	include/net/irda/
 F:	net/irda/
 
 ISAPNP
-P:	Jaroslav Kysela
-M:	perex@perex.cz
+M:	Jaroslav Kysela <perex@perex.cz>
 S:	Maintained
 F:	Documentation/isapnp.txt
 F:	drivers/pnp/isapnp/
 F:	include/linux/isapnp.h
 
 ISCSI
-P:	Mike Christie
-M:	michaelc@cs.wisc.edu
+M:	Mike Christie <michaelc@cs.wisc.edu>
 L:	open-iscsi@googlegroups.com
 W:	www.open-iscsi.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mnc/linux-2.6-iscsi.git
@@ -3242,8 +2793,7 @@ F:	drivers/scsi/*iscsi*
 F:	include/scsi/*iscsi*
 
 ISDN SUBSYSTEM
-P:	Karsten Keil
-M:	isdn@linux-pingi.de
+M:	Karsten Keil <isdn@linux-pingi.de>
 L:	isdn4linux@listserv.isdn4linux.de (subscribers-only)
 W:	http://www.isdn4linux.de
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/isdn-2.6.git
@@ -3254,16 +2804,14 @@ F:	include/linux/isdn.h
 F:	include/linux/isdn/
 
 ISDN SUBSYSTEM (Eicon active card driver)
-P:	Armin Schindler
-M:	mac@melware.de
+M:	Armin Schindler <mac@melware.de>
 L:	isdn4linux@listserv.isdn4linux.de (subscribers-only)
 W:	http://www.melware.de
 S:	Maintained
 F:	drivers/isdn/hardware/eicon/
 
 IVTV VIDEO4LINUX DRIVER
-P:	Hans Verkuil
-M:	hverkuil@xs4all.nl
+M:	Hans Verkuil <hverkuil@xs4all.nl>
 L:	ivtv-devel@ivtvdriver.org
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
@@ -3274,8 +2822,7 @@ F:	drivers/media/video/ivtv/
 F:	include/linux/ivtv*
 
 JFS FILESYSTEM
-P:	Dave Kleikamp
-M:	shaggy@linux.vnet.ibm.com
+M:	Dave Kleikamp <shaggy@linux.vnet.ibm.com>
 L:	jfs-discussion@lists.sourceforge.net
 W:	http://jfs.sourceforge.net/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6.git
@@ -3284,15 +2831,13 @@ F:	Documentation/filesystems/jfs.txt
 F:	fs/jfs/
 
 JME NETWORK DRIVER
-P:	Guo-Fu Tseng
-M:	cooldavid@cooldavid.org
+M:	Guo-Fu Tseng <cooldavid@cooldavid.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/jme.*
 
 JOURNALLING FLASH FILE SYSTEM V2 (JFFS2)
-P:	David Woodhouse
-M:	dwmw2@infradead.org
+M:	David Woodhouse <dwmw2@infradead.org>
 L:	linux-mtd@lists.infradead.org
 W:	http://www.linux-mtd.infradead.org/doc/jffs2.html
 S:	Maintained
@@ -3300,10 +2845,8 @@ F:	fs/jffs2/
 F:	include/linux/jffs2.h
 
 JOURNALLING LAYER FOR BLOCK DEVICES (JBD)
-P:	Stephen Tweedie
-M:	sct@redhat.com
-P:	Andrew Morton
-M:	akpm@linux-foundation.org
+M:	Stephen Tweedie <sct@redhat.com>
+M:	Andrew Morton <akpm@linux-foundation.org>
 L:	linux-ext4@vger.kernel.org
 S:	Maintained
 F:	fs/jbd*/
@@ -3311,48 +2854,41 @@ F:	include/linux/ext*jbd*.h
 F:	include/linux/jbd*.h
 
 K8TEMP HARDWARE MONITORING DRIVER
-P:	Rudolf Marek
-M:	r.marek@assembler.cz
+M:	Rudolf Marek <r.marek@assembler.cz>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/k8temp
 F:	drivers/hwmon/k8temp.c
 
 KCONFIG
-P:	Roman Zippel
-M:	zippel@linux-m68k.org
+M:	Roman Zippel <zippel@linux-m68k.org>
 L:	linux-kbuild@vger.kernel.org
 S:	Maintained
 F:	Documentation/kbuild/kconfig-language.txt
 F:	scripts/kconfig/
 
 KDUMP
-P:	Vivek Goyal
-M:	vgoyal@redhat.com
-P:	Haren Myneni
-M:	hbabu@us.ibm.com
+M:	Vivek Goyal <vgoyal@redhat.com>
+M:	Haren Myneni <hbabu@us.ibm.com>
 L:	kexec@lists.infradead.org
 W:	http://lse.sourceforge.net/kdump/
 S:	Maintained
 F:	Documentation/kdump/
 
 KERNEL AUTOMOUNTER (AUTOFS)
-P:	H. Peter Anvin
-M:	hpa@zytor.com
+M:	"H. Peter Anvin" <hpa@zytor.com>
 L:	autofs@linux.kernel.org
 S:	Odd Fixes
 F:	fs/autofs/
 
 KERNEL AUTOMOUNTER v4 (AUTOFS4)
-P:	Ian Kent
-M:	raven@themaw.net
+M:	Ian Kent <raven@themaw.net>
 L:	autofs@linux.kernel.org
 S:	Maintained
 F:	fs/autofs4/
 
 KERNEL BUILD
-P:	Sam Ravnborg
-M:	sam@ravnborg.org
+M:	Sam Ravnborg <sam@ravnborg.org>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes.git
 L:	linux-kbuild@vger.kernel.org
@@ -3367,10 +2903,8 @@ W:	http://www.kerneljanitors.org/
 S:	Odd fixes
 
 KERNEL NFSD, SUNRPC, AND LOCKD SERVERS
-P:	J. Bruce Fields
-M:	bfields@fieldses.org
-P:	Neil Brown
-M:	neilb@suse.de
+M:	"J. Bruce Fields" <bfields@fieldses.org>
+M:	Neil Brown <neilb@suse.de>
 L:	linux-nfs@vger.kernel.org
 W:	http://nfs.sourceforge.net/
 S:	Supported
@@ -3383,8 +2917,7 @@ F:	include/linux/lockd/
 F:	include/linux/sunrpc/
 
 KERNEL VIRTUAL MACHINE (KVM)
-P:	Avi Kivity
-M:	avi@redhat.com
+M:	Avi Kivity <avi@redhat.com>
 L:	kvm@vger.kernel.org
 W:	http://kvm.qumranet.com
 S:	Supported
@@ -3395,8 +2928,7 @@ F:	include/linux/kvm*
 F:	virt/kvm/
 
 KERNEL VIRTUAL MACHINE (KVM) FOR AMD-V
-P:	Joerg Roedel
-M:	joerg.roedel@amd.com
+M:	Joerg Roedel <joerg.roedel@amd.com>
 L:	kvm@vger.kernel.org
 W:	http://kvm.qumranet.com
 S:	Supported
@@ -3405,8 +2937,7 @@ F:	arch/x86/kvm/kvm_svm.h
 F:	arch/x86/kvm/svm.c
 
 KERNEL VIRTUAL MACHINE (KVM) FOR POWERPC
-P:	Hollis Blanchard
-M:	hollisb@us.ibm.com
+M:	Hollis Blanchard <hollisb@us.ibm.com>
 L:	kvm-ppc@vger.kernel.org
 W:	http://kvm.qumranet.com
 S:	Supported
@@ -3414,8 +2945,7 @@ F:	arch/powerpc/include/asm/kvm*
 F:	arch/powerpc/kvm/
 
 KERNEL VIRTUAL MACHINE For Itanium (KVM/IA64)
-P:	Xiantao Zhang
-M:	xiantao.zhang@intel.com
+M:	Xiantao Zhang <xiantao.zhang@intel.com>
 L:	kvm-ia64@vger.kernel.org
 W:	http://kvm.qumranet.com
 S:	Supported
@@ -3424,10 +2954,8 @@ F:	arch/ia64/include/asm/kvm*
 F:	arch/ia64/kvm/
 
 KERNEL VIRTUAL MACHINE for s390 (KVM/s390)
-P:	Carsten Otte
-M:	cotte@de.ibm.com
-P:	Christian Borntraeger
-M:	borntraeger@de.ibm.com
+M:	Carsten Otte <cotte@de.ibm.com>
+M:	Christian Borntraeger <borntraeger@de.ibm.com>
 M:	linux390@de.ibm.com
 L:	linux-s390@vger.kernel.org
 W:	http://www.ibm.com/developerworks/linux/linux390/
@@ -3437,8 +2965,7 @@ F:	arch/s390/include/asm/kvm*
 F:	arch/s390/kvm/
 
 KEXEC
-P:	Eric Biederman
-M:	ebiederm@xmission.com
+M:	Eric Biederman <ebiederm@xmission.com>
 W:	http://ftp.kernel.org/pub/linux/kernel/people/horms/kexec-tools/
 L:	kexec@lists.infradead.org
 S:	Maintained
@@ -3446,8 +2973,7 @@ F:	include/linux/kexec.h
 F:	kernel/kexec.c
 
 KGDB
-P:	Jason Wessel
-M:	jason.wessel@windriver.com
+M:	Jason Wessel <jason.wessel@windriver.com>
 L:	kgdb-bugreport@lists.sourceforge.net
 S:	Maintained
 F:	Documentation/DocBook/kgdb.tmpl
@@ -3457,15 +2983,13 @@ F:	include/linux/kgdb.h
 F:	kernel/kgdb.c
 
 KMEMCHECK
-P:	Vegard Nossum
-M:	vegardno@ifi.uio.no
+M:	Vegard Nossum <vegardno@ifi.uio.no>
 P	Pekka Enberg
 M:	penberg@cs.helsinki.fi
 S:	Maintained
 
 KMEMLEAK
-P:	Catalin Marinas
-M:	catalin.marinas@arm.com
+M:	Catalin Marinas <catalin.marinas@arm.com>
 S:	Maintained
 F:	Documentation/kmemleak.txt
 F:	include/linux/kmemleak.h
@@ -3473,30 +2997,24 @@ F:	mm/kmemleak.c
 F:	mm/kmemleak-test.c
 
 KMEMTRACE
-P:	Eduard - Gabriel Munteanu
-M:	eduard.munteanu@linux360.ro
+M:	Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
 S:	Maintained
 F:	Documentation/trace/kmemtrace.txt
 F:	include/linux/kmemtrace.h
 F:	kernel/trace/kmemtrace.c
 
 KPROBES
-P:	Ananth N Mavinakayanahalli
-M:	ananth@in.ibm.com
-P:	Anil S Keshavamurthy
-M:	anil.s.keshavamurthy@intel.com
-P:	David S. Miller
-M:	davem@davemloft.net
-P:	Masami Hiramatsu
-M:	mhiramat@redhat.com
+M:	Ananth N Mavinakayanahalli <ananth@in.ibm.com>
+M:	Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
+M:	"David S. Miller" <davem@davemloft.net>
+M:	Masami Hiramatsu <mhiramat@redhat.com>
 S:	Maintained
 F:	Documentation/kprobes.txt
 F:	include/linux/kprobes.h
 F:	kernel/kprobes.c
 
 KS0108 LCD CONTROLLER DRIVER
-P:	Miguel Ojeda Sandonis
-M:	miguel.ojeda.sandonis@gmail.com
+M:	Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
 W:	http://miguelojeda.es/auxdisplay.htm
 W:	http://jair.lab.fi.uva.es/~migojed/auxdisplay.htm
 S:	Maintained
@@ -3512,31 +3030,27 @@ F:	include/*/lapb.h
 F:	net/lapb/
 
 LASI 53c700 driver for PARISC
-P:	James E.J. Bottomley
-M:	James.Bottomley@HansenPartnership.com
+M:	"James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	Documentation/scsi/53c700.txt
 F:	drivers/scsi/53c700*
 
 LED SUBSYSTEM
-P:	Richard Purdie
-M:	rpurdie@rpsys.net
+M:	Richard Purdie <rpurdie@rpsys.net>
 S:	Maintained
 F:	drivers/leds/
 F:	include/linux/leds.h
 
 LEGO USB Tower driver
-P:	Juergen Stuber
-M:	starblue@users.sourceforge.net
+M:	Juergen Stuber <starblue@users.sourceforge.net>
 L:	legousb-devel@lists.sourceforge.net
 W:	http://legousb.sourceforge.net/
 S:	Maintained
 F:	drivers/usb/misc/legousbtower.c
 
 LGUEST
-P:	Rusty Russell
-M:	rusty@rustcorp.com.au
+M:	Rusty Russell <rusty@rustcorp.com.au>
 L:	lguest@ozlabs.org
 W:	http://lguest.ozlabs.org/
 S:	Maintained
@@ -3547,119 +3061,100 @@ F:	include/linux/lguest*.h
 F:	arch/x86/include/asm/lguest*.h
 
 LINUX FOR IBM pSERIES (RS/6000)
-P:	Paul Mackerras
-M:	paulus@au.ibm.com
+M:	Paul Mackerras <paulus@au.ibm.com>
 W:	http://www.ibm.com/linux/ltc/projects/ppc
 S:	Supported
 
 LINUX FOR POWERPC (32-BIT AND 64-BIT)
-P:	Benjamin Herrenschmidt
-M:	benh@kernel.crashing.org
-P:	Paul Mackerras
-M:	paulus@samba.org
+M:	Benjamin Herrenschmidt <benh@kernel.crashing.org>
+M:	Paul Mackerras <paulus@samba.org>
 W:	http://www.penguinppc.org/
 L:	linuxppc-dev@ozlabs.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc.git
 S:	Supported
 
 LINUX FOR POWER MACINTOSH
-P:	Benjamin Herrenschmidt
-M:	benh@kernel.crashing.org
+M:	Benjamin Herrenschmidt <benh@kernel.crashing.org>
 W:	http://www.penguinppc.org/
 L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 
 LINUX FOR POWERPC EMBEDDED MPC5XXX
-P:	Grant Likely
-M:	grant.likely@secretlab.ca
+M:	Grant Likely <grant.likely@secretlab.ca>
 L:	linuxppc-dev@ozlabs.org
 T:	git git://git.secretlab.ca/git/linux-2.6.git
 S:	Maintained
 
 LINUX FOR POWERPC EMBEDDED PPC4XX
-P:	Josh Boyer
-M:	jwboyer@linux.vnet.ibm.com
-P:	Matt Porter
-M:	mporter@kernel.crashing.org
+M:	Josh Boyer <jwboyer@linux.vnet.ibm.com>
+M:	Matt Porter <mporter@kernel.crashing.org>
 W:	http://www.penguinppc.org/
 L:	linuxppc-dev@ozlabs.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx.git
 S:	Maintained
 
 LINUX FOR POWERPC EMBEDDED XILINX VIRTEX
-P:	Grant Likely
-M:	grant.likely@secretlab.ca
+M:	Grant Likely <grant.likely@secretlab.ca>
 W:	http://wiki.secretlab.ca/index.php/Linux_on_Xilinx_Virtex
 L:	linuxppc-dev@ozlabs.org
 T:	git git://git.secretlab.ca/git/linux-2.6.git
 S:	Maintained
 
 LINUX FOR POWERPC EMBEDDED PPC8XX
-P:	Vitaly Bordug
-M:	vitb@kernel.crashing.org
-P:	Marcelo Tosatti
-M:	marcelo@kvack.org
+M:	Vitaly Bordug <vitb@kernel.crashing.org>
+M:	Marcelo Tosatti <marcelo@kvack.org>
 W:	http://www.penguinppc.org/
 L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 
 LINUX FOR POWERPC EMBEDDED PPC83XX AND PPC85XX
-P:	Kumar Gala
-M:	galak@kernel.crashing.org
+M:	Kumar Gala <galak@kernel.crashing.org>
 W:	http://www.penguinppc.org/
 L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 
 LINUX FOR POWERPC PA SEMI PWRFICIENT
-P:	Olof Johansson
-M:	olof@lixom.net
+M:	Olof Johansson <olof@lixom.net>
 W:	http://www.pasemi.com/
 L:	linuxppc-dev@ozlabs.org
 S:	Supported
 
 LINUX SECURITY MODULE (LSM) FRAMEWORK
-P:	Chris Wright
-M:	chrisw@sous-sol.org
+M:	Chris Wright <chrisw@sous-sol.org>
 L:	linux-security-module@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/chrisw/lsm-2.6.git
 S:	Supported
 
 LLC (802.2)
-P:	Arnaldo Carvalho de Melo
-M:	acme@ghostprotocols.net
+M:	Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
 S:	Maintained
 F:	include/linux/llc.h
 F:	include/net/llc*
 F:	net/llc/
 
 LIS3LV02D ACCELEROMETER DRIVER
-P:	Eric Piel
-M:	eric.piel@tremplin-utc.net
+M:	Eric Piel <eric.piel@tremplin-utc.net>
 S:	Maintained
 F:	Documentation/hwmon/lis3lv02d
 F:	drivers/hwmon/lis3lv02d.*
 
 LM83 HARDWARE MONITOR DRIVER
-P:	Jean Delvare
-M:	khali@linux-fr.org
+M:	Jean Delvare <khali@linux-fr.org>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/lm83
 F:	drivers/hwmon/lm83.c
 
 LM90 HARDWARE MONITOR DRIVER
-P:	Jean Delvare
-M:	khali@linux-fr.org
+M:	Jean Delvare <khali@linux-fr.org>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/lm90
 F:	drivers/hwmon/lm90.c
 
 LOCKDEP AND LOCKSTAT
-P:	Peter Zijlstra
-M:	peterz@infradead.org
-P:	Ingo Molnar
-M:	mingo@redhat.com
+M:	Peter Zijlstra <peterz@infradead.org>
+M:	Ingo Molnar <mingo@redhat.com>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-lockdep.git
 S:	Maintained
 F:	Documentation/lockdep*.txt
@@ -3668,8 +3163,7 @@ F:	include/linux/lockdep.h
 F:	kernel/lockdep*
 
 LOGICAL DISK MANAGER SUPPORT (LDM, Windows 2000/XP/Vista Dynamic Disks)
-P:	Richard Russon (FlatCap)
-M:	ldm@flatcap.org
+M:	"Richard Russon (FlatCap)" <ldm@flatcap.org>
 L:	linux-ntfs-dev@lists.sourceforge.net
 W:	http://www.linux-ntfs.org/content/view/19/37/
 S:	Maintained
@@ -3677,8 +3171,7 @@ F:	Documentation/ldm.txt
 F:	fs/partitions/ldm.*
 
 LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
-P:	Eric Moore
-M:	Eric.Moore@lsi.com
+M:	Eric Moore <Eric.Moore@lsi.com>
 M:	support@lsi.com
 L:	DL-MPTFusionLinux@lsi.com
 L:	linux-scsi@vger.kernel.org
@@ -3687,25 +3180,21 @@ S:	Supported
 F:	drivers/message/fusion/
 
 LSILOGIC/SYMBIOS/NCR 53C8XX and 53C1010 PCI-SCSI drivers
-P:	Matthew Wilcox
-M:	matthew@wil.cx
+M:	Matthew Wilcox <matthew@wil.cx>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/sym53c8xx_2/
 
 LTP (Linux Test Project)
-P:	Subrata Modak
-M:	subrata@linux.vnet.ibm.com
-P:	Mike Frysinger
-M:	vapier@gentoo.org
+M:	Subrata Modak <subrata@linux.vnet.ibm.com>
+M:	Mike Frysinger <vapier@gentoo.org>
 L:	ltp-list@lists.sourceforge.net (subscribers-only)
 W:	http://ltp.sourceforge.net/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/galak/ltp.git
 S:	Maintained
 
 M32R ARCHITECTURE
-P:	Hirokazu Takata
-M:	takata@linux-m32r.org
+M:	Hirokazu Takata <takata@linux-m32r.org>
 L:	linux-m32r@ml.linux-m32r.org
 L:	linux-m32r-ja@ml.linux-m32r.org (in Japanese)
 W:	http://www.linux-m32r.org/
@@ -3713,10 +3202,8 @@ S:	Maintained
 F:	arch/m32r/
 
 M68K ARCHITECTURE
-P:	Geert Uytterhoeven
-M:	geert@linux-m68k.org
-P:	Roman Zippel
-M:	zippel@linux-m68k.org
+M:	Geert Uytterhoeven <geert@linux-m68k.org>
+M:	Roman Zippel <zippel@linux-m68k.org>
 L:	linux-m68k@lists.linux-m68k.org
 W:	http://www.linux-m68k.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k.git
@@ -3725,23 +3212,20 @@ F:	arch/m68k/
 F:	drivers/zorro/
 
 M68K ON APPLE MACINTOSH
-P:	Joshua Thompson
-M:	funaho@jurai.org
+M:	Joshua Thompson <funaho@jurai.org>
 W:	http://www.mac.linux-m68k.org/
 L:	linux-m68k@lists.linux-m68k.org
 S:	Maintained
 F:	arch/m68k/mac/
 
 M68K ON HP9000/300
-P:	Philip Blundell
-M:	philb@gnu.org
+M:	Philip Blundell <philb@gnu.org>
 W:	http://www.tazenda.demon.co.uk/phil/linux-hp
 S:	Maintained
 F:	arch/m68k/hp300/
 
 MAC80211
-P:	Johannes Berg
-M:	johannes@sipsolutions.net
+M:	Johannes Berg <johannes@sipsolutions.net>
 L:	linux-wireless@vger.kernel.org
 W:	http://linuxwireless.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6.git
@@ -3751,10 +3235,8 @@ F:	include/net/mac80211.h
 F:	net/mac80211/
 
 MAC80211 PID RATE CONTROL
-P:	Stefano Brivio
-M:	stefano.brivio@polimi.it
-P:	Mattias Nissler
-M:	mattias.nissler@gmx.de
+M:	Stefano Brivio <stefano.brivio@polimi.it>
+M:	Mattias Nissler <mattias.nissler@gmx.de>
 L:	linux-wireless@vger.kernel.org
 W:	http://linuxwireless.org/en/developers/Documentation/mac80211/RateControl/PID
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6.git
@@ -3762,67 +3244,57 @@ S:	Maintained
 F:	net/mac80211/rc80211_pid*
 
 MACVLAN DRIVER
-P:	Patrick McHardy
-M:	kaber@trash.net
+M:	Patrick McHardy <kaber@trash.net>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/macvlan.c
 F:	include/linux/if_macvlan.h
 
 MAN-PAGES: MANUAL PAGES FOR LINUX -- Sections 2, 3, 4, 5, and 7
-P:	Michael Kerrisk
-M:	mtk.manpages@gmail.com
+M:	Michael Kerrisk <mtk.manpages@gmail.com>
 W:	http://www.kernel.org/doc/man-pages
 L:	linux-man@vger.kernel.org
 S:	Maintained
 
 MARVELL LIBERTAS WIRELESS DRIVER
-P:	Dan Williams
-M:	dcbw@redhat.com
+M:	Dan Williams <dcbw@redhat.com>
 L:	libertas-dev@lists.infradead.org
 S:	Maintained
 F:	drivers/net/wireless/libertas/
 
 MARVELL MV643XX ETHERNET DRIVER
-P:	Lennert Buytenhek
-M:	buytenh@marvell.com
+M:	Lennert Buytenhek <buytenh@marvell.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/mv643xx_eth.*
 F:	include/linux/mv643xx.h
 
 MARVELL SOC MMC/SD/SDIO CONTROLLER DRIVER
-P:	Nicolas Pitre
-M:	nico@cam.org
+M:	Nicolas Pitre <nico@cam.org>
 S:	Maintained
 
 MARVELL YUKON / SYSKONNECT DRIVER
-P:	Mirko Lindner
-M:	mlindner@syskonnect.de
-P:	Ralph Roesler
-M:	rroesler@syskonnect.de
+M:	Mirko Lindner <mlindner@syskonnect.de>
+M:	Ralph Roesler <rroesler@syskonnect.de>
 W:	http://www.syskonnect.com
 S:	Supported
 
 MATROX FRAMEBUFFER DRIVER
-P:	Petr Vandrovec
-M:	vandrove@vc.cvut.cz
+M:	Petr Vandrovec <vandrove@vc.cvut.cz>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/video/matrox/matroxfb_*
 F:	include/linux/matroxfb.h
 
 MAX6650 HARDWARE MONITOR AND FAN CONTROLLER DRIVER
-P:	Hans J. Koch
-M:	hjk@linutronix.de
+M:	"Hans J. Koch" <hjk@linutronix.de>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/max6650
 F:	drivers/hwmon/max6650.c
 
 MEDIA INPUT INFRASTRUCTURE (V4L/DVB)
-P:	Mauro Carvalho Chehab
-M:	mchehab@infradead.org
+M:	Mauro Carvalho Chehab <mchehab@infradead.org>
 P:	LinuxTV.org Project
 L:	linux-media@vger.kernel.org
 W:	http://linuxtv.org
@@ -3836,8 +3308,7 @@ F:	include/linux/dvb/
 F:	include/linux/videodev*.h
 
 MEGARAID SCSI DRIVERS
-P:	Neela Syam Kolli
-M:	megaraidlinux@lsi.com
+M:	Neela Syam Kolli <megaraidlinux@lsi.com>
 L:	linux-scsi@vger.kernel.org
 W:	http://megaraid.lsilogic.com
 S:	Maintained
@@ -3853,19 +3324,15 @@ F:	include/linux/mm.h
 F:	mm/
 
 MEMORY RESOURCE CONTROLLER
-P:	Balbir Singh
-M:	balbir@linux.vnet.ibm.com
-P:	Pavel Emelyanov
-M:	xemul@openvz.org
-P:	KAMEZAWA Hiroyuki
-M:	kamezawa.hiroyu@jp.fujitsu.com
+M:	Balbir Singh <balbir@linux.vnet.ibm.com>
+M:	Pavel Emelyanov <xemul@openvz.org>
+M:	KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
 L:	linux-mm@kvack.org
 S:	Maintained
 F:	mm/memcontrol.c
 
 MEMORY TECHNOLOGY DEVICES (MTD)
-P:	David Woodhouse
-M:	dwmw2@infradead.org
+M:	David Woodhouse <dwmw2@infradead.org>
 W:	http://www.linux-mtd.infradead.org/
 L:	linux-mtd@lists.infradead.org
 T:	git git://git.infradead.org/mtd-2.6.git
@@ -3875,8 +3342,7 @@ F:	include/linux/mtd/
 F:	include/mtd/
 
 MICROBLAZE ARCHITECTURE
-P:	Michal Simek
-M:	monstr@monstr.eu
+M:	Michal Simek <monstr@monstr.eu>
 L:	microblaze-uclinux@itee.uq.edu.au
 W:	http://www.monstr.eu/fdt/
 T:	git git://git.monstr.eu/linux-2.6-microblaze.git
@@ -3884,14 +3350,12 @@ S:	Supported
 F:	arch/microblaze/
 
 MICROTEK X6 SCANNER
-P:	Oliver Neukum
-M:	oliver@neukum.name
+M:	Oliver Neukum <oliver@neukum.name>
 S:	Maintained
 F:	drivers/usb/image/microtek.*
 
 MIPS
-P:	Ralf Baechle
-M:	ralf@linux-mips.org
+M:	Ralf Baechle <ralf@linux-mips.org>
 W:	http://www.linux-mips.org/
 L:	linux-mips@linux-mips.org
 T:	git git://git.linux-mips.org/pub/scm/linux.git
@@ -3900,8 +3364,7 @@ F:	Documentation/mips/
 F:	arch/mips/
 
 MISCELLANEOUS MCA-SUPPORT
-P:	James Bottomley
-M:	James.Bottomley@HansenPartnership.com
+M:	James Bottomley <James.Bottomley@HansenPartnership.com>
 S:	Maintained
 F:	Documentation/ia64/mca.txt
 F:	Documentation/mca.txt
@@ -3909,15 +3372,13 @@ F:	drivers/mca/
 F:	include/linux/mca*
 
 MODULE SUPPORT
-P:	Rusty Russell
-M:	rusty@rustcorp.com.au
+M:	Rusty Russell <rusty@rustcorp.com.au>
 S:	Maintained
 F:	include/linux/module.h
 F:	kernel/module.c
 
 MOTION EYE VAIO PICTUREBOOK CAMERA DRIVER
-P:	Stelian Pop
-M:	stelian@popies.net
+M:	Stelian Pop <stelian@popies.net>
 W:	http://popies.net/meye/
 S:	Maintained
 F:	Documentation/video4linux/meye.txt
@@ -3925,135 +3386,112 @@ F:	drivers/media/video/meye.*
 F:	include/linux/meye.h
 
 MOTOROLA IMX MMC/SD HOST CONTROLLER INTERFACE DRIVER
-P:	Pavel Pisa
-M:	ppisa@pikron.com
+M:	Pavel Pisa <ppisa@pikron.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Maintained
 F:	drivers/mmc/host/imxmmc.*
 
 MOUSE AND MISC DEVICES [GENERAL]
-P:	Alessandro Rubini
-M:	rubini@ipvvis.unipv.it
+M:	Alessandro Rubini <rubini@ipvvis.unipv.it>
 S:	Maintained
 F:	drivers/input/mouse/
 F:	include/linux/gpio_mouse.h
 
 MOXA SMARTIO/INDUSTIO/INTELLIO SERIAL CARD
-P:	Jiri Slaby
-M:	jirislaby@gmail.com
+M:	Jiri Slaby <jirislaby@gmail.com>
 S:	Maintained
 F:	Documentation/serial/moxa-smartio
 F:	drivers/char/mxser.*
 
 MSI LAPTOP SUPPORT
-P:	Lennart Poettering
-M:	mzxreary@0pointer.de
+M:	Lennart Poettering <mzxreary@0pointer.de>
 W:	https://tango.0pointer.de/mailman/listinfo/s270-linux
 W:	http://0pointer.de/lennart/tchibo.html
 S:	Maintained
 F:	drivers/platform/x86/msi-laptop.c
 
 MULTIFUNCTION DEVICES (MFD)
-P:	Samuel Ortiz
-M:	sameo@linux.intel.com
+M:	Samuel Ortiz <sameo@linux.intel.com>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6.git
 S:	Supported
 F:	drivers/mfd/
 
 MULTIMEDIA CARD (MMC), SECURE DIGITAL (SD) AND SDIO SUBSYSTEM
-P:	Pierre Ossman
-M:	pierre@ossman.eu
+M:	Pierre Ossman <pierre@ossman.eu>
 S:	Maintained
 F:	drivers/mmc/
 F:	include/linux/mmc/
 
 MULTIMEDIA CARD (MMC) ETC. OVER SPI
-P:	David Brownell
-M:	dbrownell@users.sourceforge.net
+M:	David Brownell <dbrownell@users.sourceforge.net>
 S:	Odd Fixes
 F:	drivers/mmc/host/mmc_spi.c
 F:	include/linux/spi/mmc_spi.h
 
 MULTISOUND SOUND DRIVER
-P:	Andrew Veliath
-M:	andrewtv@usa.net
+M:	Andrew Veliath <andrewtv@usa.net>
 S:	Maintained
 F:	Documentation/sound/oss/MultiSound
 F:	sound/oss/msnd*
 
 MULTITECH MULTIPORT CARD (ISICOM)
-P:	Jiri Slaby
-M:	jirislaby@gmail.com
+M:	Jiri Slaby <jirislaby@gmail.com>
 S:	Maintained
 F:	drivers/char/isicom.c
 F:	include/linux/isicom.h
 
 MUSB MULTIPOINT HIGH SPEED DUAL-ROLE CONTROLLER
-P:	Felipe Balbi
-M:	felipe.balbi@nokia.com
+M:	Felipe Balbi <felipe.balbi@nokia.com>
 L:	linux-usb@vger.kernel.org
 T:	git git://gitorious.org/musb/mainline.git
 S:	Maintained
 F:	drivers/usb/musb/
 
 MYRICOM MYRI-10G 10GbE DRIVER (MYRI10GE)
-P:	Andrew Gallatin
-M:	gallatin@myri.com
-P:	Brice Goglin
-M:	brice@myri.com
+M:	Andrew Gallatin <gallatin@myri.com>
+M:	Brice Goglin <brice@myri.com>
 L:	netdev@vger.kernel.org
 W:	http://www.myri.com/scs/download-Myri10GE.html
 S:	Supported
 F:	drivers/net/myri10ge/
 
 NATSEMI ETHERNET DRIVER (DP8381x)
-P:	Tim Hockin
-M:	thockin@hockin.org
+M:	Tim Hockin <thockin@hockin.org>
 S:	Maintained
 F:	drivers/net/natsemi.c
 
 NCP FILESYSTEM
-P:	Petr Vandrovec
-M:	vandrove@vc.cvut.cz
+M:	Petr Vandrovec <vandrove@vc.cvut.cz>
 L:	linware@sh.cvut.cz
 S:	Maintained
 F:	fs/ncpfs/
 
 NCR DUAL 700 SCSI DRIVER (MICROCHANNEL)
-P:	James E.J. Bottomley
-M:	James.Bottomley@HansenPartnership.com
+M:	"James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/NCR_D700.*
 
 NETEFFECT IWARP RNIC DRIVER (IW_NES)
-P:	Faisal Latif
-M:	faisal.latif@intel.com
-P:	Chien Tung
-M:	chien.tin.tung@intel.com
+M:	Faisal Latif <faisal.latif@intel.com>
+M:	Chien Tung <chien.tin.tung@intel.com>
 L:	general@lists.openfabrics.org
 W:	http://www.neteffect.com
 S:	Supported
 F:	drivers/infiniband/hw/nes/
 
 NETEM NETWORK EMULATOR
-P:	Stephen Hemminger
-M:	shemminger@linux-foundation.org
+M:	Stephen Hemminger <shemminger@linux-foundation.org>
 L:	netem@lists.linux-foundation.org
 S:	Maintained
 F:	net/sched/sch_netem.c
 
 NETERION (S2IO) 10GbE DRIVER (xframe/vxge)
-P:	Ramkrishna Vepa
-M:	ram.vepa@neterion.com
-P:	Rastapur Santosh
-M:	santosh.rastapur@neterion.com
-P:	Sivakumar Subramani
-M:	sivakumar.subramani@neterion.com
-P:	Sreenivasa Honnur
-M:	sreenivasa.honnur@neterion.com
-P:	Anil Murthy
-M:	anil.murthy@neterion.com
+M:	Ramkrishna Vepa <ram.vepa@neterion.com>
+M:	Rastapur Santosh <santosh.rastapur@neterion.com>
+M:	Sivakumar Subramani <sivakumar.subramani@neterion.com>
+M:	Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
+M:	Anil Murthy <anil.murthy@neterion.com>
 L:	netdev@vger.kernel.org
 W:	http://trac.neterion.com/cgi-bin/trac.cgi/wiki/Linux?Anonymous
 W:	http://trac.neterion.com/cgi-bin/trac.cgi/wiki/X3100Linux?Anonymous
@@ -4067,8 +3505,7 @@ P:	Marc Boucher
 P:	James Morris
 P:	Harald Welte
 P:	Jozsef Kadlecsik
-P:	Patrick McHardy
-M:	kaber@trash.net
+M:	Patrick McHardy <kaber@trash.net>
 L:	netfilter-devel@vger.kernel.org
 L:	netfilter@vger.kernel.org
 L:	coreteam@netfilter.org
@@ -4084,8 +3521,7 @@ F:	net/*/netfilter/
 F:	net/netfilter/
 
 NETLABEL
-P:	Paul Moore
-M:	paul.moore@hp.com
+M:	Paul Moore <paul.moore@hp.com>
 W:	http://netlabel.sf.net
 L:	netdev@vger.kernel.org
 S:	Supported
@@ -4094,8 +3530,7 @@ F:	include/net/netlabel.h
 F:	net/netlabel/
 
 NETROM NETWORK LAYER
-P:	Ralf Baechle
-M:	ralf@linux-mips.org
+M:	Ralf Baechle <ralf@linux-mips.org>
 L:	linux-hams@vger.kernel.org
 W:	http://www.linux-ax25.org/
 S:	Maintained
@@ -4104,16 +3539,14 @@ F:	include/net/netrom.h
 F:	net/netrom/
 
 NETWORK BLOCK DEVICE (NBD)
-P:	Paul Clements
-M:	Paul.Clements@steeleye.com
+M:	Paul Clements <Paul.Clements@steeleye.com>
 S:	Maintained
 F:	Documentation/blockdev/nbd.txt
 F:	drivers/block/nbd.c
 F:	include/linux/nbd.h
 
 NETWORKING [GENERAL]
-P:	David S. Miller
-M:	davem@davemloft.net
+M:	"David S. Miller" <davem@davemloft.net>
 L:	netdev@vger.kernel.org
 W:	http://www.linuxfoundation.org/en/Net
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git
@@ -4122,18 +3555,12 @@ F:	net/
 F:	include/net/
 
 NETWORKING [IPv4/IPv6]
-P:	David S. Miller
-M:	davem@davemloft.net
-P:	Alexey Kuznetsov
-M:	kuznet@ms2.inr.ac.ru
-P:	Pekka Savola (ipv6)
-M:	pekkas@netcore.fi
-P:	James Morris
-M:	jmorris@namei.org
-P:	Hideaki YOSHIFUJI
-M:	yoshfuji@linux-ipv6.org
-P:	Patrick McHardy
-M:	kaber@trash.net
+M:	"David S. Miller" <davem@davemloft.net>
+M:	Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
+M:	"Pekka Savola (ipv6)" <pekkas@netcore.fi>
+M:	James Morris <jmorris@namei.org>
+M:	Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
+M:	Patrick McHardy <kaber@trash.net>
 L:	netdev@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git
 S:	Maintained
@@ -4142,14 +3569,12 @@ F:	net/ipv6/
 F:	include/net/ip*
 
 NETWORKING [LABELED] (NetLabel, CIPSO, Labeled IPsec, SECMARK)
-P:	Paul Moore
-M:	paul.moore@hp.com
+M:	Paul Moore <paul.moore@hp.com>
 L:	netdev@vger.kernel.org
 S:	Maintained
 
 NETWORKING [WIRELESS]
-P:	John W. Linville
-M:	linville@tuxdriver.com
+M:	"John W. Linville" <linville@tuxdriver.com>
 L:	linux-wireless@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6.git
 S:	Maintained
@@ -4165,16 +3590,14 @@ S:	Odd Fixes
 F:	drivers/net/
 
 NETXEN (1/10) GbE SUPPORT
-P:	Dhananjay Phadke
-M:	dhananjay@netxen.com
+M:	Dhananjay Phadke <dhananjay@netxen.com>
 L:	netdev@vger.kernel.org
 W:	http://www.netxen.com
 S:	Supported
 F:	drivers/net/netxen/
 
 NFS, SUNRPC, AND LOCKD CLIENTS
-P:	Trond Myklebust
-M:	Trond.Myklebust@netapp.com
+M:	Trond Myklebust <Trond.Myklebust@netapp.com>
 L:	linux-nfs@vger.kernel.org
 W:	http://client.linux-nfs.org
 T:	git git://git.linux-nfs.org/pub/linux/nfs-2.6.git
@@ -4188,17 +3611,14 @@ F:	include/linux/nfs*
 F:	include/linux/sunrpc/
 
 NI5010 NETWORK DRIVER
-P:	Jan-Pascal van Best
-M:	janpascal@vanbest.org
-P:	Andreas Mohr
-M:	andi@lisas.de
+M:	Jan-Pascal van Best <janpascal@vanbest.org>
+M:	Andreas Mohr <andi@lisas.de>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/ni5010.*
 
 NILFS2 FILESYSTEM
-P:	KONISHI Ryusuke
-M:	konishi.ryusuke@lab.ntt.co.jp
+M:	KONISHI Ryusuke <konishi.ryusuke@lab.ntt.co.jp>
 L:	users@nilfs.org
 W:	http://www.nilfs.org/en/
 S:	Supported
@@ -4207,26 +3627,22 @@ F:	fs/nilfs2/
 F:	include/linux/nilfs2_fs.h
 
 NINJA SCSI-3 / NINJA SCSI-32Bi (16bit/CardBus) PCMCIA SCSI HOST ADAPTER DRIVER
-P:	YOKOTA Hiroshi
-M:	yokota@netlab.is.tsukuba.ac.jp
+M:	YOKOTA Hiroshi <yokota@netlab.is.tsukuba.ac.jp>
 W:	http://www.netlab.is.tsukuba.ac.jp/~yokota/izumi/ninja/
 S:	Maintained
 F:	Documentation/scsi/NinjaSCSI.txt
 F:	drivers/scsi/pcmcia/nsp_*
 
 NINJA SCSI-32Bi/UDE PCI/CARDBUS SCSI HOST ADAPTER DRIVER
-P:	GOTO Masanori
-M:	gotom@debian.or.jp
-P:	YOKOTA Hiroshi
-M:	yokota@netlab.is.tsukuba.ac.jp
+M:	GOTO Masanori <gotom@debian.or.jp>
+M:	YOKOTA Hiroshi <yokota@netlab.is.tsukuba.ac.jp>
 W:	http://www.netlab.is.tsukuba.ac.jp/~yokota/izumi/ninja/
 S:	Maintained
 F:	Documentation/scsi/NinjaSCSI.txt
 F:	drivers/scsi/nsp32*
 
 NTFS FILESYSTEM
-P:	Anton Altaparmakov
-M:	aia21@cantab.net
+M:	Anton Altaparmakov <aia21@cantab.net>
 L:	linux-ntfs-dev@lists.sourceforge.net
 W:	http://www.linux-ntfs.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/aia21/ntfs-2.6.git
@@ -4235,16 +3651,14 @@ F:	Documentation/filesystems/ntfs.txt
 F:	fs/ntfs/
 
 NVIDIA (rivafb and nvidiafb) FRAMEBUFFER DRIVER
-P:	Antonino Daplas
-M:	adaplas@gmail.com
+M:	Antonino Daplas <adaplas@gmail.com>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/video/riva/
 F:	drivers/video/nvidia/
 
 OMAP SUPPORT
-P:	Tony Lindgren <tony@atomide.com>
-M:	tony@atomide.com
+M:	"Tony Lindgren <tony@atomide.com>" <tony@atomide.com>
 L:	linux-omap@vger.kernel.org
 W:	http://www.muru.com/linux/omap/
 W:	http://linux.omap.com/
@@ -4253,97 +3667,83 @@ S:	Maintained
 F:	arch/arm/*omap*
 
 OMAP CLOCK FRAMEWORK SUPPORT
-P:	Paul Walmsley
-M:	paul@pwsan.com
+M:	Paul Walmsley <paul@pwsan.com>
 L:	linux-omap@vger.kernel.org
 S:	Maintained
 F:	arch/arm/*omap*/*clock*
 
 OMAP POWER MANAGEMENT SUPPORT
-P:	Kevin Hilman
-M:	khilman@deeprootsystems.com
+M:	Kevin Hilman <khilman@deeprootsystems.com>
 L:	linux-omap@vger.kernel.org
 S:	Maintained
 F:	arch/arm/*omap*/*pm*
 
 OMAP AUDIO SUPPORT
-P:	Jarkko Nikula
-M:	jhnikula@gmail.com
+M:	Jarkko Nikula <jhnikula@gmail.com>
 L:	alsa-devel@alsa-project.org (subscribers-only)
 L:	linux-omap@vger.kernel.org
 S:	Maintained
 F:	sound/soc/omap/
 
 OMAP FRAMEBUFFER SUPPORT
-P:	Imre Deak
-M:	imre.deak@nokia.com
+M:	Imre Deak <imre.deak@nokia.com>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 L:	linux-omap@vger.kernel.org
 S:	Maintained
 F:	drivers/video/omap/
 
 OMAP MMC SUPPORT
-P:	Jarkko Lavinen
-M:	jarkko.lavinen@nokia.com
+M:	Jarkko Lavinen <jarkko.lavinen@nokia.com>
 L:	linux-omap@vger.kernel.org
 S:	Maintained
 F:	drivers/mmc/host/*omap*
 
 OMAP RANDOM NUMBER GENERATOR SUPPORT
-P:	Deepak Saxena
-M:	dsaxena@plexity.net
+M:	Deepak Saxena <dsaxena@plexity.net>
 S:	Maintained
 F:	drivers/char/hw_random/omap-rng.c
 
 OMAP USB SUPPORT
-P:	Felipe Balbi
-M:	felipe.balbi@nokia.com
-P:	David Brownell
-M:	dbrownell@users.sourceforge.net
+M:	Felipe Balbi <felipe.balbi@nokia.com>
+M:	David Brownell <dbrownell@users.sourceforge.net>
 L:	linux-usb@vger.kernel.org
 L:	linux-omap@vger.kernel.org
 S:	Maintained
 
 OMFS FILESYSTEM
-P:	Bob Copeland
-M:	me@bobcopeland.com
+M:	Bob Copeland <me@bobcopeland.com>
 L:	linux-karma-devel@lists.sourceforge.net
 S:	Maintained
 F:	Documentation/filesystems/omfs.txt
 F:	fs/omfs/
 
 OMNIKEY CARDMAN 4000 DRIVER
-P:	Harald Welte
-M:	laforge@gnumonks.org
+M:	Harald Welte <laforge@gnumonks.org>
 S:	Maintained
 F:	drivers/char/pcmcia/cm4000_cs.c
 F:	include/linux/cm4000_cs.h
 
 OMNIKEY CARDMAN 4040 DRIVER
-P:	Harald Welte
-M:	laforge@gnumonks.org
+M:	Harald Welte <laforge@gnumonks.org>
 S:	Maintained
 F:	drivers/char/pcmcia/cm4040_cs.*
 
 OMNIVISION OV7670 SENSOR DRIVER
-P:	Jonathan Corbet
-M:	corbet@lwn.net
+M:	Jonathan Corbet <corbet@lwn.net>
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 S:	Maintained
 F:	drivers/media/video/ov7670.c
 
 ONENAND FLASH DRIVER
-P:	Kyungmin Park
-M:	kyungmin.park@samsung.com
+M:	Kyungmin Park <kyungmin.park@samsung.com>
 L:	linux-mtd@lists.infradead.org
 S:	Maintained
 F:	drivers/mtd/onenand/
 F:	include/linux/mtd/onenand*.h
 
 ONSTREAM SCSI TAPE DRIVER
-P:	Willem Riede
-M:	osst@riede.org
+M:	Willem Riede <osst@riede.org>
 L:	osst-users@lists.sourceforge.net
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
@@ -4351,16 +3751,14 @@ F:	drivers/scsi/osst*
 F:	drivers/scsi/st*
 
 OPENCORES I2C BUS DRIVER
-P:	Peter Korsgaard
-M:	jacmet@sunsite.dk
+M:	Peter Korsgaard <jacmet@sunsite.dk>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	Documentation/i2c/busses/i2c-ocores
 F:	drivers/i2c/busses/i2c-ocores.c
 
 OPROFILE
-P:	Robert Richter
-M:	robert.richter@amd.com
+M:	Robert Richter <robert.richter@amd.com>
 L:	oprofile-list@lists.sf.net
 S:	Maintained
 F:	arch/*/oprofile/
@@ -4368,10 +3766,8 @@ F:	drivers/oprofile/
 F:	include/linux/oprofile.h
 
 ORACLE CLUSTER FILESYSTEM 2 (OCFS2)
-P:	Mark Fasheh
-M:	mfasheh@suse.com
-P:	Joel Becker
-M:	joel.becker@oracle.com
+M:	Mark Fasheh <mfasheh@suse.com>
+M:	Joel Becker <joel.becker@oracle.com>
 L:	ocfs2-devel@oss.oracle.com (moderated for non-subscribers)
 W:	http://oss.oracle.com/projects/ocfs2/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2.git
@@ -4381,10 +3777,8 @@ F:	Documentation/filesystems/dlmfs.txt
 F:	fs/ocfs2/
 
 ORINOCO DRIVER
-P:	Pavel Roskin
-M:	proski@gnu.org
-P:	David Gibson
-M:	hermes@gibson.dropbear.id.au
+M:	Pavel Roskin <proski@gnu.org>
+M:	David Gibson <hermes@gibson.dropbear.id.au>
 L:	linux-wireless@vger.kernel.org
 L:	orinoco-users@lists.sourceforge.net
 L:	orinoco-devel@lists.sourceforge.net
@@ -4393,10 +3787,8 @@ S:	Maintained
 F:	drivers/net/wireless/orinoco/
 
 OSD LIBRARY and FILESYSTEM
-P:	Boaz Harrosh
-M:	bharrosh@panasas.com
-P:	Benny Halevy
-M:	bhalevy@panasas.com
+M:	Boaz Harrosh <bharrosh@panasas.com>
+M:	Benny Halevy <bhalevy@panasas.com>
 L:	osd-dev@open-osd.org
 W:	http://open-osd.org
 T:	git git://git.open-osd.org/open-osd.git
@@ -4406,8 +3798,7 @@ F:	drivers/include/scsi/osd_*
 F:	fs/exofs/
 
 P54 WIRELESS DRIVER
-P:	Michael Wu
-M:	flamingice@sourmilk.net
+M:	Michael Wu <flamingice@sourmilk.net>
 L:	linux-wireless@vger.kernel.org
 W:	http://prism54.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mwu/mac80211-drivers.git
@@ -4415,30 +3806,25 @@ S:	Maintained
 F:	drivers/net/wireless/p54/
 
 PA SEMI ETHERNET DRIVER
-P:	Olof Johansson
-M:	olof@lixom.net
+M:	Olof Johansson <olof@lixom.net>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/pasemi_mac.*
 
 PA SEMI SMBUS DRIVER
-P:	Olof Johansson
-M:	olof@lixom.net
+M:	Olof Johansson <olof@lixom.net>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	drivers/i2c/busses/i2c-pasemi.c
 
 PANASONIC LAPTOP ACPI EXTRAS DRIVER
-P:	Harald Welte
-M:	laforge@gnumonks.org
+M:	Harald Welte <laforge@gnumonks.org>
 S:	Maintained
 F:	drivers/platform/x86/panasonic-laptop.c
 
 PANASONIC MN10300/AM33 PORT
-P:	David Howells
-M:	dhowells@redhat.com
-P:	Koichi Yasutake
-M:	yasutake.koichi@jp.panasonic.com
+M:	David Howells <dhowells@redhat.com>
+M:	Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
 L:	linux-am33-list@redhat.com (moderated for non-subscribers)
 W:	ftp://ftp.redhat.com/pub/redhat/gnupro/AM33/
 S:	Maintained
@@ -4454,14 +3840,10 @@ F:	drivers/char/ppdev.c
 F:	include/linux/ppdev.h
 
 PARAVIRT_OPS INTERFACE
-P:	Jeremy Fitzhardinge
-M:	jeremy@xensource.com
-P:	Chris Wright
-M:	chrisw@sous-sol.org
-P:	Alok Kataria
-M:	akataria@vmware.com
-P:	Rusty Russell
-M:	rusty@rustcorp.com.au
+M:	Jeremy Fitzhardinge <jeremy@xensource.com>
+M:	Chris Wright <chrisw@sous-sol.org>
+M:	Alok Kataria <akataria@vmware.com>
+M:	Rusty Russell <rusty@rustcorp.com.au>
 L:	virtualization@lists.osdl.org
 S:	Supported
 F:	Documentation/ia64/paravirt_ops.txt
@@ -4469,8 +3851,7 @@ F:	arch/*/kernel/paravirt*
 F:	arch/*/include/asm/paravirt.h
 
 PARIDE DRIVERS FOR PARALLEL PORT IDE DEVICES
-P:	Tim Waugh
-M:	tim@cyberelk.net
+M:	Tim Waugh <tim@cyberelk.net>
 L:	linux-parport@lists.infradead.org (subscribers-only)
 W:	http://www.torque.net/linux-pp.html
 S:	Maintained
@@ -4478,10 +3859,8 @@ F:	Documentation/blockdev/paride.txt
 F:	drivers/block/paride/
 
 PARISC ARCHITECTURE
-P:	Kyle McMartin
-M:	kyle@mcmartin.ca
-P:	Helge Deller
-M:	deller@gmx.de
+M:	Kyle McMartin <kyle@mcmartin.ca>
+M:	Helge Deller <deller@gmx.de>
 L:	linux-parisc@vger.kernel.org
 W:	http://www.parisc-linux.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6.git
@@ -4490,37 +3869,32 @@ F:	arch/parisc/
 F:	drivers/parisc/
 
 PC87360 HARDWARE MONITORING DRIVER
-P:	Jim Cromie
-M:	jim.cromie@gmail.com
+M:	Jim Cromie <jim.cromie@gmail.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/pc87360
 F:	drivers/hwmon/pc87360.c
 
 PC8736x GPIO DRIVER
-P:	Jim Cromie
-M:	jim.cromie@gmail.com
+M:	Jim Cromie <jim.cromie@gmail.com>
 S:	Maintained
 F:	drivers/char/pc8736x_gpio.c
 
 PCA9532 LED DRIVER
-P:	Riku Voipio
-M:	riku.voipio@iki.fi
+M:	Riku Voipio <riku.voipio@iki.fi>
 S:	Maintained
 F:	drivers/leds/leds-pca9532.c
 F:	include/linux/leds-pca9532.h
 
 PCI ERROR RECOVERY
-P:	Linas Vepstas
-M:	linas@austin.ibm.com
+M:	Linas Vepstas <linas@austin.ibm.com>
 L:	linux-pci@vger.kernel.org
 S:	Supported
 F:	Documentation/PCI/pci-error-recovery.txt
 F:	Documentation/powerpc/eeh-pci-error-recovery.txt
 
 PCI SUBSYSTEM
-P:	Jesse Barnes
-M:	jbarnes@virtuousgeek.org
+M:	Jesse Barnes <jbarnes@virtuousgeek.org>
 L:	linux-pci@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6.git
 S:	Supported
@@ -4529,8 +3903,7 @@ F:	drivers/pci/
 F:	include/linux/pci*
 
 PCIE HOTPLUG DRIVER
-P:	Kristen Carlson Accardi
-M:	kristen.c.accardi@intel.com
+M:	Kristen Carlson Accardi <kristen.c.accardi@intel.com>
 L:	linux-pci@vger.kernel.org
 S:	Supported
 F:	drivers/pci/pcie/
@@ -4546,113 +3919,94 @@ F:	drivers/pcmcia/
 F:	include/pcmcia/
 
 PCNET32 NETWORK DRIVER
-P:	Don Fry
-M:	pcnet32@verizon.net
+M:	Don Fry <pcnet32@verizon.net>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/pcnet32.c
 
 PER-TASK DELAY ACCOUNTING
-P:	Balbir Singh
-M:	balbir@linux.vnet.ibm.com
+M:	Balbir Singh <balbir@linux.vnet.ibm.com>
 S:	Maintained
 F:	include/linux/delayacct.h
 F:	kernel/delayacct.c
 
 PERFORMANCE COUNTER SUBSYSTEM
-P:	Peter Zijlstra
-M:	a.p.zijlstra@chello.nl
-P:	Paul Mackerras
-M:	paulus@samba.org
-P:	Ingo Molnar
-M:	mingo@elte.hu
+M:	Peter Zijlstra <a.p.zijlstra@chello.nl>
+M:	Paul Mackerras <paulus@samba.org>
+M:	Ingo Molnar <mingo@elte.hu>
 S:	Supported
 
 PERSONALITY HANDLING
-P:	Christoph Hellwig
-M:	hch@infradead.org
+M:	Christoph Hellwig <hch@infradead.org>
 L:	linux-abi-devel@lists.sourceforge.net
 S:	Maintained
 F:	include/linux/personality.h
 
 PHRAM MTD DRIVER
-P:	Joern Engel
-M:	joern@lazybastard.org
+M:	Joern Engel <joern@lazybastard.org>
 L:	linux-mtd@lists.infradead.org
 S:	Maintained
 F:	drivers/mtd/devices/phram.c
 
 PKTCDVD DRIVER
-P:	Peter Osterlund
-M:	petero2@telia.com
+M:	Peter Osterlund <petero2@telia.com>
 S:	Maintained
 F:	drivers/block/pktcdvd.c
 F:	include/linux/pktcdvd.h
 
 POSIX CLOCKS and TIMERS
-P:	Thomas Gleixner
-M:	tglx@linutronix.de
+M:	Thomas Gleixner <tglx@linutronix.de>
 S:	Supported
 F:	fs/timerfd.c
 F:	include/linux/timer*
 F:	kernel/*timer*
 
 POWER SUPPLY CLASS/SUBSYSTEM and DRIVERS
-P:	Anton Vorontsov
-M:	cbou@mail.ru
-P:	David Woodhouse
-M:	dwmw2@infradead.org
+M:	Anton Vorontsov <cbou@mail.ru>
+M:	David Woodhouse <dwmw2@infradead.org>
 T:	git git://git.infradead.org/battery-2.6.git
 S:	Maintained
 F:	include/linux/power_supply.h
 F:	drivers/power/power_supply*
 
 PNP SUPPORT
-P:	Adam Belay
-M:	abelay@mit.edu
-P:	Bjorn Helgaas
-M:	bjorn.helgaas@hp.com
+M:	Adam Belay <abelay@mit.edu>
+M:	Bjorn Helgaas <bjorn.helgaas@hp.com>
 S:	Maintained
 F:	drivers/pnp/
 
 PNXxxxx I2C DRIVER
-P:	Vitaly Wool
-M:	vitalywool@gmail.com
+M:	Vitaly Wool <vitalywool@gmail.com>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	drivers/i2c/busses/i2c-pnx.c
 
 PPP PROTOCOL DRIVERS AND COMPRESSORS
-P:	Paul Mackerras
-M:	paulus@samba.org
+M:	Paul Mackerras <paulus@samba.org>
 L:	linux-ppp@vger.kernel.org
 S:	Maintained
 F:	drivers/net/ppp_*
 
 PPP OVER ATM (RFC 2364)
-P:	Mitchell Blank Jr
-M:	mitch@sfgoth.com
+M:	Mitchell Blank Jr <mitch@sfgoth.com>
 S:	Maintained
 F:	net/atm/pppoatm.c
 F:	include/linux/atmppp.h
 
 PPP OVER ETHERNET
-P:	Michal Ostrowski
-M:	mostrows@earthlink.net
+M:	Michal Ostrowski <mostrows@earthlink.net>
 S:	Maintained
 F:	drivers/net/pppoe.c
 F:	drivers/net/pppox.c
 
 PPP OVER L2TP
-P:	James Chapman
-M:	jchapman@katalix.com
+M:	James Chapman <jchapman@katalix.com>
 S:	Maintained
 F:	drivers/net/pppol2tp.c
 F:	include/linux/if_pppol2tp.h
 
 PPS SUPPORT
-P:	Rodolfo Giometti
-M:	giometti@enneenne.com
+M:	Rodolfo Giometti <giometti@enneenne.com>
 W:	http://wiki.enneenne.com/index.php/LinuxPPS_support
 L:	linuxpps@ml.enneenne.com (subscribers-only)
 S:	Maintained
@@ -4661,8 +4015,7 @@ F:	drivers/pps/
 F:	include/linux/pps*.h
 
 PREEMPTIBLE KERNEL
-P:	Robert Love
-M:	rml@tech9.net
+M:	Robert Love <rml@tech9.net>
 L:	kpreempt-tech@lists.sourceforge.net
 W:	ftp://ftp.kernel.org/pub/linux/kernel/people/rml/preempt-kernel
 S:	Supported
@@ -4670,37 +4023,32 @@ F:	Documentation/preempt-locking.txt
 F:	include/linux/preempt.h
 
 PRISM54 WIRELESS DRIVER
-P:	Luis R. Rodriguez
-M:	mcgrof@gmail.com
+M:	"Luis R. Rodriguez" <mcgrof@gmail.com>
 L:	linux-wireless@vger.kernel.org
 W:	http://prism54.org
 S:	Maintained
 F:	drivers/net/wireless/prism54/
 
 PROMISE DC4030 CACHING DISK CONTROLLER DRIVER
-P:	Peter Denison
-M:	promise@pnd-pc.demon.co.uk
+M:	Peter Denison <promise@pnd-pc.demon.co.uk>
 W:	http://www.pnd-pc.demon.co.uk/promise/
 S:	Maintained
 
 PROMISE SATA TX2/TX4 CONTROLLER LIBATA DRIVER
-P:	Mikael Pettersson
-M:	mikpe@it.uu.se
+M:	Mikael Pettersson <mikpe@it.uu.se>
 L:	linux-ide@vger.kernel.org
 S:	Maintained
 F:	drivers/ata/sata_promise.*
 
 PS3 NETWORK SUPPORT
-P:	Geoff Levand
-M:	geoffrey.levand@am.sony.com
+M:	Geoff Levand <geoffrey.levand@am.sony.com>
 L:	netdev@vger.kernel.org
 L:	cbe-oss-dev@ozlabs.org
 S:	Supported
 F:	drivers/net/ps3_gelic_net.*
 
 PS3 PLATFORM SUPPORT
-P:	Geoff Levand
-M:	geoffrey.levand@am.sony.com
+M:	Geoff Levand <geoffrey.levand@am.sony.com>
 L:	linuxppc-dev@ozlabs.org
 L:	cbe-oss-dev@ozlabs.org
 S:	Supported
@@ -4715,16 +4063,13 @@ F:	drivers/usb/host/*ps3.c
 F:	sound/ppc/snd_ps3*
 
 PS3VRAM DRIVER
-P:	Jim Paris
-M:	jim@jtan.com
+M:	Jim Paris <jim@jtan.com>
 L:	cbe-oss-dev@ozlabs.org
 S:	Maintained
 
 PTRACE SUPPORT
-P:	Roland McGrath
-M:	roland@redhat.com
-P:	Oleg Nesterov
-M:	oleg@redhat.com
+M:	Roland McGrath <roland@redhat.com>
+M:	Oleg Nesterov <oleg@redhat.com>
 S:	Maintained
 F:	include/asm-generic/syscall.h
 F:	include/linux/ptrace.h
@@ -4733,8 +4078,7 @@ F:	include/linux/tracehook.h
 F:	kernel/ptrace.c
 
 PVRUSB2 VIDEO4LINUX DRIVER
-P:	Mike Isely
-M:	isely@pobox.com
+M:	Mike Isely <isely@pobox.com>
 L:	pvrusb2@isely.net	(subscribers-only)
 L:	linux-media@vger.kernel.org
 W:	http://www.isely.net/pvrusb2/
@@ -4744,10 +4088,8 @@ F:	Documentation/video4linux/README.pvrusb2
 F:	drivers/media/video/pvrusb2/
 
 PXA2xx/PXA3xx SUPPORT
-P:	Eric Miao
-M:	eric.y.miao@gmail.com
-P:	Russell King
-M:	linux@arm.linux.org.uk
+M:	Eric Miao <eric.y.miao@gmail.com>
+M:	Russell King <linux@arm.linux.org.uk>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 S:	Maintained
 F:	arch/arm/mach-pxa/
@@ -4759,17 +4101,14 @@ F:	sound/arm/pxa*
 F:	sound/soc/pxa
 
 PXA168 SUPPORT
-P:	Eric Miao
-M:	eric.y.miao@gmail.com
-P:	Jason Chagas
-M:	jason.chagas@marvell.com
+M:	Eric Miao <eric.y.miao@gmail.com>
+M:	Jason Chagas <jason.chagas@marvell.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6.git
 S:	Maintained
 
 PXA910 SUPPORT
-P:	Eric Miao
-M:	eric.y.miao@gmail.com
+M:	Eric Miao <eric.y.miao@gmail.com>
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6.git
 S:	Maintained
@@ -4778,14 +4117,12 @@ PXA MMCI DRIVER
 S:	Orphan
 
 PXA RTC DRIVER
-P:	Robert Jarzmik
-M:	robert.jarzmik@free.fr
+M:	Robert Jarzmik <robert.jarzmik@free.fr>
 L:	rtc-linux@googlegroups.com
 S:	Maintained
 
 QLOGIC QLA2XXX FC-SCSI DRIVER
-P:	Andrew Vasquez
-M:	andrew.vasquez@qlogic.com
+M:	Andrew Vasquez <andrew.vasquez@qlogic.com>
 M:	linux-driver@qlogic.com
 L:	linux-scsi@vger.kernel.org
 S:	Supported
@@ -4793,8 +4130,7 @@ F:	Documentation/scsi/LICENSE.qla2xxx
 F:	drivers/scsi/qla2xxx/
 
 QLOGIC QLA3XXX NETWORK DRIVER
-P:	Ron Mercer
-M:	ron.mercer@qlogic.com
+M:	Ron Mercer <ron.mercer@qlogic.com>
 M:	linux-driver@qlogic.com
 L:	netdev@vger.kernel.org
 S:	Supported
@@ -4802,16 +4138,14 @@ F:	Documentation/networking/LICENSE.qla3xxx
 F:	drivers/net/qla3xxx.*
 
 QLOGIC QLGE 10Gb ETHERNET DRIVER
-P:	Ron Mercer
-M:	ron.mercer@qlogic.com
+M:	Ron Mercer <ron.mercer@qlogic.com>
 M:	linux-driver@qlogic.com
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/qlge/
 
 QNX4 FILESYSTEM
-P:	Anders Larsen
-M:	al@alarsen.net
+M:	Anders Larsen <al@alarsen.net>
 W:	http://www.alarsen.net/linux/qnx4fs/
 S:	Maintained
 F:	fs/qnx4/
@@ -4819,16 +4153,14 @@ F:	include/linux/qnx4_fs.h
 F:	include/linux/qnxtypes.h
 
 RADEON FRAMEBUFFER DISPLAY DRIVER
-P:	Benjamin Herrenschmidt
-M:	benh@kernel.crashing.org
+M:	Benjamin Herrenschmidt <benh@kernel.crashing.org>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/video/aty/radeon*
 F:	include/linux/radeonfb.h
 
 RAGE128 FRAMEBUFFER DISPLAY DRIVER
-P:	Paul Mackerras
-M:	paulus@samba.org
+M:	Paul Mackerras <paulus@samba.org>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/video/aty/aty128fb.c
@@ -4843,64 +4175,53 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/ivd/rt2x00.git
 F:	drivers/net/wireless/rt2x00/
 
 RAMDISK RAM BLOCK DEVICE DRIVER
-P:	Nick Piggin
-M:	npiggin@suse.de
+M:	Nick Piggin <npiggin@suse.de>
 S:	Maintained
 F:	Documentation/blockdev/ramdisk.txt
 F:	drivers/block/brd.c
 
 RANDOM NUMBER DRIVER
-P:	Matt Mackall
-M:	mpm@selenic.com
+M:	Matt Mackall <mpm@selenic.com>
 S:	Maintained
 F:	drivers/char/random.c
 
 RAPIDIO SUBSYSTEM
-P:	Matt Porter
-M:	mporter@kernel.crashing.org
+M:	Matt Porter <mporter@kernel.crashing.org>
 S:	Maintained
 F:	drivers/rapidio/
 
 RAYLINK/WEBGEAR 802.11 WIRELESS LAN DRIVER
-P:	Corey Thomas
-M:	coreythomas@charter.net
+M:	Corey Thomas <coreythomas@charter.net>
 L:	linux-wireless@vger.kernel.org
 S:	Maintained
 F:	drivers/net/wireless/ray*
 
 RCUTORTURE MODULE
-P:	Josh Triplett
-M:	josh@freedesktop.org
-P:	Paul E. McKenney
-M:	paulmck@linux.vnet.ibm.com
+M:	Josh Triplett <josh@freedesktop.org>
+M:	"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
 S:	Maintained
 F:	Documentation/RCU/torture.txt
 F:	kernel/rcutorture.c
 
 RDC R-321X SoC
-P:	Florian Fainelli
-M:	florian@openwrt.org
+M:	Florian Fainelli <florian@openwrt.org>
 S:	Maintained
 
 RDC R6040 FAST ETHERNET DRIVER
-P:	Florian Fainelli
-M:	florian@openwrt.org
+M:	Florian Fainelli <florian@openwrt.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/r6040.c
 
 RDS - RELIABLE DATAGRAM SOCKETS
-P:	Andy Grover
-M:	andy.grover@oracle.com
+M:	Andy Grover <andy.grover@oracle.com>
 L:	rds-devel@oss.oracle.com (moderated for non-subscribers)
 S:	Supported
 F:	net/rds/
 
 READ-COPY UPDATE (RCU)
-P:	Dipankar Sarma
-M:	dipankar@in.ibm.com
-P:	Paul E. McKenney
-M:	paulmck@linux.vnet.ibm.com
+M:	Dipankar Sarma <dipankar@in.ibm.com>
+M:	"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
 W:	http://www.rdrop.com/users/paulmck/rclock/
 S:	Supported
 F:	Documentation/RCU/rcu.txt
@@ -4910,16 +4231,14 @@ F:	include/linux/srcu.h
 F:	kernel/rcupdate.c
 
 REAL TIME CLOCK DRIVER
-P:	Paul Gortmaker
-M:	p_gortmaker@yahoo.com
+M:	Paul Gortmaker <p_gortmaker@yahoo.com>
 S:	Maintained
 F:	Documentation/rtc.txt
 F:	drivers/rtc/
 F:	include/linux/rtc.h
 
 REAL TIME CLOCK (RTC) SUBSYSTEM
-P:	Alessandro Zummo
-M:	a.zummo@towertech.it
+M:	Alessandro Zummo <a.zummo@towertech.it>
 L:	rtc-linux@googlegroups.com
 S:	Maintained
 F:	Documentation/rtc.txt
@@ -4932,8 +4251,7 @@ S:	Supported
 F:	fs/reiserfs/
 
 RFKILL
-P:	Johannes Berg
-M:	johannes@sipsolutions.net
+M:	Johannes Berg <johannes@sipsolutions.net>
 L:	linux-wireless@vger.kernel.org
 S:	Maintained
 F	Documentation/rfkill.txt
@@ -4952,8 +4270,7 @@ F:	Documentation/serial/rocket.txt
 F:	drivers/char/rocket*
 
 ROSE NETWORK LAYER
-P:	Ralf Baechle
-M:	ralf@linux-mips.org
+M:	Ralf Baechle <ralf@linux-mips.org>
 L:	linux-hams@vger.kernel.org
 W:	http://www.linux-ax25.org/
 S:	Maintained
@@ -4962,8 +4279,7 @@ F:	include/net/rose.h
 F:	net/rose/
 
 RTL8180 WIRELESS DRIVER
-P:	John W. Linville
-M:	linville@tuxdriver.com
+M:	"John W. Linville" <linville@tuxdriver.com>
 L:	linux-wireless@vger.kernel.org
 W:	http://linuxwireless.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-testing.git
@@ -4971,12 +4287,9 @@ S:	Maintained
 F:	drivers/net/wireless/rtl818*
 
 RTL8187 WIRELESS DRIVER
-P:	Herton Ronaldo Krzesinski
-M:	herton@mandriva.com.br
-P:	Hin-Tak Leung
-M:	htl10@users.sourceforge.net
-P:	Larry Finger
-M:	Larry.Finger@lwfinger.net
+M:	Herton Ronaldo Krzesinski <herton@mandriva.com.br>
+M:	Hin-Tak Leung <htl10@users.sourceforge.net>
+M:	Larry Finger <Larry.Finger@lwfinger.net>
 L:	linux-wireless@vger.kernel.org
 W:	http://linuxwireless.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-testing.git
@@ -4984,17 +4297,14 @@ S:	Maintained
 F:	drivers/net/wireless/rtl818x/rtl8187*
 
 S3 SAVAGE FRAMEBUFFER DRIVER
-P:	Antonino Daplas
-M:	adaplas@gmail.com
+M:	Antonino Daplas <adaplas@gmail.com>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/video/savage/
 
 S390
-P:	Martin Schwidefsky
-M:	schwidefsky@de.ibm.com
-P:	Heiko Carstens
-M:	heiko.carstens@de.ibm.com
+M:	Martin Schwidefsky <schwidefsky@de.ibm.com>
+M:	Heiko Carstens <heiko.carstens@de.ibm.com>
 M:	linux390@de.ibm.com
 L:	linux-s390@vger.kernel.org
 W:	http://www.ibm.com/developerworks/linux/linux390/
@@ -5002,10 +4312,8 @@ S:	Supported
 F:	arch/s390/
 
 S390 NETWORK DRIVERS
-P:	Ursula Braun
-M:	ursula.braun@de.ibm.com
-P:	Frank Blaschka
-M:	blaschka@linux.vnet.ibm.com
+M:	Ursula Braun <ursula.braun@de.ibm.com>
+M:	Frank Blaschka <blaschka@linux.vnet.ibm.com>
 M:	linux390@de.ibm.com
 L:	linux-s390@vger.kernel.org
 W:	http://www.ibm.com/developerworks/linux/linux390/
@@ -5013,20 +4321,16 @@ S:	Supported
 F:	drivers/s390/net/
 
 S390 ZCRYPT DRIVER
-P:	Felix Beck
-M:	felix.beck@de.ibm.com
-P:	Ralph Wuerthner
-M:	ralph.wuerthner@de.ibm.com
+M:	Felix Beck <felix.beck@de.ibm.com>
+M:	Ralph Wuerthner <ralph.wuerthner@de.ibm.com>
 M:	linux390@de.ibm.com
 L:	linux-s390@vger.kernel.org
 S:	Supported
 F:	drivers/s390/crypto/
 
 S390 ZFCP DRIVER
-P:	Christof Schmitt
-M:	christof.schmitt@de.ibm.com
-P:	Martin Peschke
-M:	mp3@de.ibm.com
+M:	Christof Schmitt <christof.schmitt@de.ibm.com>
+M:	Martin Peschke <mp3@de.ibm.com>
 M:	linux390@de.ibm.com
 L:	linux-s390@vger.kernel.org
 W:	http://www.ibm.com/developerworks/linux/linux390/
@@ -5035,8 +4339,7 @@ F:	Documentation/s390/zfcpdump.txt
 F:	drivers/s390/scsi/zfcp_*
 
 S390 IUCV NETWORK LAYER
-P:	Ursula Braun
-M:	ursula.braun@de.ibm.com
+M:	Ursula Braun <ursula.braun@de.ibm.com>
 M:	linux390@de.ibm.com
 L:	linux-s390@vger.kernel.org
 W:	http://www.ibm.com/developerworks/linux/linux390/
@@ -5046,15 +4349,13 @@ F:	include/net/iucv/
 F:	net/iucv/
 
 S3C24XX SD/MMC Driver
-P:	Ben Dooks
-M:	ben-linux@fluff.org
+M:	Ben Dooks <ben-linux@fluff.org>
 L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
 S:	Supported
 F:	drivers/mmc/host/s3cmci.*
 
 SAA7146 VIDEO4LINUX-2 DRIVER
-P:	Michael Hunold
-M:	michael@mihu.de
+M:	Michael Hunold <michael@mihu.de>
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 W:	http://www.mihu.de/linux/saa7146
@@ -5064,31 +4365,26 @@ F:	drivers/media/video/*7146*
 F:	include/media/*7146*
 
 SC1200 WDT DRIVER
-P:	Zwane Mwaikambo
-M:	zwane@arm.linux.org.uk
+M:	Zwane Mwaikambo <zwane@arm.linux.org.uk>
 S:	Maintained
 F:	drivers/watchdog/sc1200wdt.c
 
 SCHEDULER
-P:	Ingo Molnar
-M:	mingo@elte.hu
-P:	Peter Zijlstra
-M:	peterz@infradead.org
+M:	Ingo Molnar <mingo@elte.hu>
+M:	Peter Zijlstra <peterz@infradead.org>
 S:	Maintained
 F:	kernel/sched*
 F:	include/linux/sched.h
 
 SCSI CDROM DRIVER
-P:	Jens Axboe
-M:	axboe@kernel.dk
+M:	Jens Axboe <axboe@kernel.dk>
 L:	linux-scsi@vger.kernel.org
 W:	http://www.kernel.dk
 S:	Maintained
 F:	drivers/scsi/sr*
 
 SCSI SG DRIVER
-P:	Doug Gilbert
-M:	dgilbert@interlog.com
+M:	Doug Gilbert <dgilbert@interlog.com>
 L:	linux-scsi@vger.kernel.org
 W:	http://www.torque.net/sg
 S:	Maintained
@@ -5096,8 +4392,7 @@ F:	drivers/scsi/sg.c
 F:	include/scsi/sg.h
 
 SCSI SUBSYSTEM
-P:	James E.J. Bottomley
-M:	James.Bottomley@HansenPartnership.com
+M:	"James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
 L:	linux-scsi@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6.git
@@ -5107,18 +4402,15 @@ F:	drivers/scsi/
 F:	include/scsi/
 
 SCSI TAPE DRIVER
-P:	Kai Mäkisara
-M:	Kai.Makisara@kolumbus.fi
+M:	Kai Mäkisara <Kai.Makisara@kolumbus.fi>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	Documentation/scsi/st.txt
 F:	drivers/scsi/st*
 
 SCTP PROTOCOL
-P:	Vlad Yasevich
-M:	vladislav.yasevich@hp.com
-P:	Sridhar Samudrala
-M:	sri@us.ibm.com
+M:	Vlad Yasevich <vladislav.yasevich@hp.com>
+M:	Sridhar Samudrala <sri@us.ibm.com>
 L:	linux-sctp@vger.kernel.org
 W:	http://lksctp.sourceforge.net
 S:	Supported
@@ -5128,8 +4420,7 @@ F:	include/net/sctp/
 F:	net/sctp/
 
 SCx200 CPU SUPPORT
-P:	Jim Cromie
-M:	jim.cromie@gmail.com
+M:	Jim Cromie <jim.cromie@gmail.com>
 S:	Odd Fixes
 F:	Documentation/i2c/busses/scx200_acb
 F:	arch/x86/kernel/scx200_32.c
@@ -5139,49 +4430,42 @@ F:	drivers/mtd/maps/scx200_docflash.c
 F:	include/linux/scx200.h
 
 SCx200 GPIO DRIVER
-P:	Jim Cromie
-M:	jim.cromie@gmail.com
+M:	Jim Cromie <jim.cromie@gmail.com>
 S:	Maintained
 F:	drivers/char/scx200_gpio.c
 F:	include/linux/scx200_gpio.h
 
 SCx200 HRT CLOCKSOURCE DRIVER
-P:	Jim Cromie
-M:	jim.cromie@gmail.com
+M:	Jim Cromie <jim.cromie@gmail.com>
 S:	Maintained
 F:	drivers/clocksource/scx200_hrt.c
 
 SDRICOH_CS MMC/SD HOST CONTROLLER INTERFACE DRIVER
-P:	Sascha Sommer
-M:	saschasommer@freenet.de
+M:	Sascha Sommer <saschasommer@freenet.de>
 L:	sdricohcs-devel@lists.sourceforge.net (subscribers-only)
 S:	Maintained
 F:	drivers/mmc/host/sdricoh_cs.c
 
 SECURE DIGITAL HOST CONTROLLER INTERFACE (SDHCI) DRIVER
-P:	Pierre Ossman
-M:	pierre@ossman.eu
+M:	Pierre Ossman <pierre@ossman.eu>
 L:	sdhci-devel@lists.ossman.eu
 S:	Maintained
 
 SECURE DIGITAL HOST CONTROLLER INTERFACE, OPEN FIRMWARE BINDINGS (SDHCI-OF)
-P:	Anton Vorontsov
-M:	avorontsov@ru.mvista.com
+M:	Anton Vorontsov <avorontsov@ru.mvista.com>
 L:	linuxppc-dev@ozlabs.org
 L:	sdhci-devel@lists.ossman.eu
 S:	Maintained
 F:	drivers/mmc/host/sdhci.*
 
 SECURE DIGITAL HOST CONTROLLER INTERFACE (SDHCI) SAMSUNG DRIVER
-P:	Ben Dooks
-M:	ben-linux@fluff.org
+M:	Ben Dooks <ben-linux@fluff.org>
 L:	sdhci-devel@lists.ossman.eu
 S:	Maintained
 F:	drivers/mmc/host/sdhci-s3c.c
 
 SECURITY SUBSYSTEM
-P:	James Morris
-M:	jmorris@namei.org
+M:	James Morris <jmorris@namei.org>
 L:	linux-security-module@vger.kernel.org (suggested Cc:)
 T:	git git://www.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6.git
 W:	http://security.wiki.kernel.org/
@@ -5189,17 +4473,13 @@ S:	Supported
 F:	security/
 
 SECURITY CONTACT
-P:	Security Officers
-M:	security@kernel.org
+M:	Security Officers <security@kernel.org>
 S:	Supported
 
 SELINUX SECURITY MODULE
-P:	Stephen Smalley
-M:	sds@tycho.nsa.gov
-P:	James Morris
-M:	jmorris@namei.org
-P:	Eric Paris
-M:	eparis@parisplace.org
+M:	Stephen Smalley <sds@tycho.nsa.gov>
+M:	James Morris <jmorris@namei.org>
+M:	Eric Paris <eparis@parisplace.org>
 L:	selinux@tycho.nsa.gov (subscribers-only, general discussion)
 W:	http://selinuxproject.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6.git
@@ -5208,15 +4488,13 @@ F:	include/linux/selinux*
 F:	security/selinux/
 
 SENSABLE PHANTOM
-P:	Jiri Slaby
-M:	jirislaby@gmail.com
+M:	Jiri Slaby <jirislaby@gmail.com>
 S:	Maintained
 F:	drivers/misc/phantom.c
 F:	include/linux/phantom.h
 
 SERIAL ATA (SATA) SUBSYSTEM
-P:	Jeff Garzik
-M:	jgarzik@pobox.com
+M:	Jeff Garzik <jgarzik@pobox.com>
 L:	linux-ide@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git
 S:	Supported
@@ -5225,10 +4503,8 @@ F:	include/linux/ata.h
 F:	include/linux/libata.h
 
 SERVER ENGINES 10Gbps NIC - BladeEngine 2 DRIVER
-P:	Sathya Perla
-M:	sathyap@serverengines.com
-P:	Subbu Seetharaman
-M:	subbus@serverengines.com
+M:	Sathya Perla <sathyap@serverengines.com>
+M:	Subbu Seetharaman <subbus@serverengines.com>
 L:	netdev@vger.kernel.org
 W:	http://www.serverengines.com
 S:	Supported
@@ -5237,20 +4513,17 @@ F:	drivers/net/benet/
 SFC NETWORK DRIVER
 P:	Steve Hodgson
 P:	Ben Hutchings
-P:	Robert Stonehouse
-M:	linux-net-drivers@solarflare.com
+M:	Robert Stonehouse <linux-net-drivers@solarflare.com>
 S:	Supported
 F:	drivers/net/sfc/
 
 SGI GRU DRIVER
-P:	Jack Steiner
-M:	steiner@sgi.com
+M:	Jack Steiner <steiner@sgi.com>
 S:	Maintained
 F:	drivers/misc/sgi-gru/
 
 SGI SN-IA64 (Altix) SERIAL CONSOLE DRIVER
-P:	Pat Gefre
-M:	pfg@sgi.com
+M:	Pat Gefre <pfg@sgi.com>
 L:	linux-ia64@vger.kernel.org
 S:	Supported
 F:	Documentation/ia64/serial.txt
@@ -5258,22 +4531,19 @@ F:	drivers/serial/ioc?_serial.c
 F:	include/linux/ioc?.h
 
 SGI VISUAL WORKSTATION 320 AND 540
-P:	Andrey Panin
-M:	pazke@donpac.ru
+M:	Andrey Panin <pazke@donpac.ru>
 L:	linux-visws-devel@lists.sf.net
 W:	http://linux-visws.sf.net
 S:	Maintained for 2.6.
 F:	Documentation/sgi-visws.txt
 
 SGI XP/XPC/XPNET DRIVER
-P:	Robin Holt
-M:	holt@sgi.com
+M:	Robin Holt <holt@sgi.com>
 S:	Maintained
 F:	drivers/misc/sgi-xp/
 
 SHARP LH SUPPORT (LH7952X & LH7A40X)
-P:	Marc Singer
-M:	elf@buici.com
+M:	Marc Singer <elf@buici.com>
 W:	http://projects.buici.com/arm
 L:	linux-arm-kernel@lists.arm.linux.org.uk	(subscribers-only)
 S:	Maintained
@@ -5284,23 +4554,20 @@ F:	drivers/usb/gadget/lh7a40*
 F:	drivers/usb/host/ohci-lh7a40*
 
 SHPC HOTPLUG DRIVER
-P:	Kristen Carlson Accardi
-M:	kristen.c.accardi@intel.com
+M:	Kristen Carlson Accardi <kristen.c.accardi@intel.com>
 L:	linux-pci@vger.kernel.org
 S:	Supported
 F:	drivers/pci/hotplug/shpchp*
 
 SIMTEC EB110ATX (Chalice CATS)
 P:	Ben Dooks
-P:	Vincent Sanders
-M:	support@simtec.co.uk
+M:	Vincent Sanders <support@simtec.co.uk>
 W:	http://www.simtec.co.uk/products/EB110ATX/
 S:	Supported
 
 SIMTEC EB2410ITX (BAST)
 P:	Ben Dooks
-P:	Vincent Sanders
-M:	support@simtec.co.uk
+M:	Vincent Sanders <support@simtec.co.uk>
 W:	http://www.simtec.co.uk/products/EB2410ITX/
 S:	Supported
 F:	arch/arm/mach-s3c2410/
@@ -5308,31 +4575,27 @@ F:	drivers/*/*s3c2410*
 F:	drivers/*/*/*s3c2410*
 
 SIS 190 ETHERNET DRIVER
-P:	Francois Romieu
-M:	romieu@fr.zoreil.com
+M:	Francois Romieu <romieu@fr.zoreil.com>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/sis190.c
 
 SIS 900/7016 FAST ETHERNET DRIVER
-P:	Daniele Venzano
-M:	venza@brownhat.org
+M:	Daniele Venzano <venza@brownhat.org>
 W:	http://www.brownhat.org/sis900.html
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/sis900.*
 
 SIS 96X I2C/SMBUS DRIVER
-P:	Mark M. Hoffman
-M:	mhoffman@lightlink.com
+M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	Documentation/i2c/busses/i2c-sis96x
 F:	drivers/i2c/busses/i2c-sis96x.c
 
 SIS FRAMEBUFFER DRIVER
-P:	Thomas Winischhofer
-M:	thomas@winischhofer.net
+M:	Thomas Winischhofer <thomas@winischhofer.net>
 W:	http://www.winischhofer.net/linuxsisvga.shtml
 S:	Maintained
 F:	Documentation/fb/sisfb.txt
@@ -5340,70 +4603,59 @@ F:	drivers/video/sis/
 F:	include/video/sisfb.h
 
 SIS USB2VGA DRIVER
-P:	Thomas Winischhofer
-M:	thomas@winischhofer.net
+M:	Thomas Winischhofer <thomas@winischhofer.net>
 W:	http://www.winischhofer.at/linuxsisusbvga.shtml
 S:	Maintained
 F:	drivers/usb/misc/sisusbvga/
 
 SKGE, SKY2 10/100/1000 GIGABIT ETHERNET DRIVERS
-P:	Stephen Hemminger
-M:	shemminger@linux-foundation.org
+M:	Stephen Hemminger <shemminger@linux-foundation.org>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/skge.*
 F:	drivers/net/sky2.*
 
 SLAB ALLOCATOR
-P:	Christoph Lameter
-M:	cl@linux-foundation.org
-P:	Pekka Enberg
-M:	penberg@cs.helsinki.fi
-P:	Matt Mackall
-M:	mpm@selenic.com
+M:	Christoph Lameter <cl@linux-foundation.org>
+M:	Pekka Enberg <penberg@cs.helsinki.fi>
+M:	Matt Mackall <mpm@selenic.com>
 L:	linux-mm@kvack.org
 S:	Maintained
 F:	include/linux/sl?b*.h
 F:	mm/sl?b.c
 
 SMC91x ETHERNET DRIVER
-P:	Nicolas Pitre
-M:	nico@cam.org
+M:	Nicolas Pitre <nico@cam.org>
 S:	Maintained
 F:	drivers/net/smc91x.*
 
 SMSC47B397 HARDWARE MONITOR DRIVER
-P:	Mark M. Hoffman
-M:	mhoffman@lightlink.com
+M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/smsc47b397
 F:	drivers/hwmon/smsc47b397.c
 
 SMSC911x ETHERNET DRIVER
-P:	Steve Glendinning
-M:	steve.glendinning@smsc.com
+M:	Steve Glendinning <steve.glendinning@smsc.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	include/linux/smsc911x.h
 F:	drivers/net/smsc911x.*
 
 SMSC9420 PCI ETHERNET DRIVER
-P:	Steve Glendinning
-M:	steve.glendinning@smsc.com
+M:	Steve Glendinning <steve.glendinning@smsc.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/smsc9420.*
 
 SMX UIO Interface
-P:	Ben Nizette
-M:	bn@niasdigital.com
+M:	Ben Nizette <bn@niasdigital.com>
 S:	Maintained
 F:	drivers/uio/uio_smx.c
 
 SN-IA64 (Itanium) SUB-PLATFORM
-P:	Jes Sorensen
-M:	jes@sgi.com
+M:	Jes Sorensen <jes@sgi.com>
 L:	linux-altix@sgi.com
 L:	linux-ia64@vger.kernel.org
 W:	http://www.sgi.com/altix
@@ -5411,8 +4663,7 @@ S:	Maintained
 F:	arch/ia64/sn/
 
 SOC-CAMERA V4L2 SUBSYSTEM
-P:	Guennadi Liakhovetski
-M:	g.liakhovetski@gmx.de
+M:	Guennadi Liakhovetski <g.liakhovetski@gmx.de>
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 S:	Maintained
@@ -5420,37 +4671,32 @@ F:	include/media/v4l2*
 F:	drivers/media/video/v4l2*
 
 SOEKRIS NET48XX LED SUPPORT
-P:	Chris Boot
-M:	bootc@bootc.net
+M:	Chris Boot <bootc@bootc.net>
 S:	Maintained
 F:	drivers/leds/leds-net48xx.c
 
 SOFTWARE RAID (Multiple Disks) SUPPORT
-P:	Neil Brown
-M:	neilb@suse.de
+M:	Neil Brown <neilb@suse.de>
 L:	linux-raid@vger.kernel.org
 S:	Supported
 F:	drivers/md/
 F:	include/linux/raid/
 
 SONIC NETWORK DRIVER
-P:	Thomas Bogendoerfer
-M:	tsbogend@alpha.franken.de
+M:	Thomas Bogendoerfer <tsbogend@alpha.franken.de>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/sonic.*
 
 SONICS SILICON BACKPLANE DRIVER (SSB)
-P:	Michael Buesch
-M:	mb@bu3sch.de
+M:	Michael Buesch <mb@bu3sch.de>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/ssb/
 F:	include/linux/ssb/
 
 SONY VAIO CONTROL DEVICE DRIVER
-P:	Mattia Dongili
-M:	malattia@linux.it
+M:	Mattia Dongili <malattia@linux.it>
 L:	linux-acpi@vger.kernel.org
 W:	http://www.linux.it/~malattia/wiki/index.php/Sony_drivers
 S:	Maintained
@@ -5460,17 +4706,14 @@ F:	drivers/platform/x86/sony-laptop.c
 F:	include/linux/sony-laptop.h
 
 SONY MEMORYSTICK CARD SUPPORT
-P:	Alex Dubov
-M:	oakad@yahoo.com
+M:	Alex Dubov <oakad@yahoo.com>
 W:	http://tifmxx.berlios.de/
 S:	Maintained
 F:	drivers/memstick/host/tifm_ms.c
 
 SOUND
-P:	Jaroslav Kysela
-M:	perex@perex.cz
-P:	Takashi Iwai
-M:	tiwai@suse.de
+M:	Jaroslav Kysela <perex@perex.cz>
+M:	Takashi Iwai <tiwai@suse.de>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 W:	http://www.alsa-project.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6.git
@@ -5481,10 +4724,8 @@ F:	include/sound/
 F:	sound/
 
 SOUND - SOC LAYER / DYNAMIC AUDIO POWER MANAGEMENT (ASoC)
-P:	Liam Girdwood
-M:	lrg@slimlogic.co.uk
-P:	Mark Brown
-M:	broonie@opensource.wolfsonmicro.com
+M:	Liam Girdwood <lrg@slimlogic.co.uk>
+M:	Mark Brown <broonie@opensource.wolfsonmicro.com>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6.git
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 W:	http://alsa-project.org/main/index.php/ASoC
@@ -5493,8 +4734,7 @@ F:	sound/soc/
 F:	include/sound/soc*
 
 SPARC + UltraSPARC (sparc/sparc64)
-P:	David S. Miller
-M:	davem@davemloft.net
+M:	"David S. Miller" <davem@davemloft.net>
 L:	sparclinux@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6.git
@@ -5502,15 +4742,13 @@ S:	Maintained
 F:	arch/sparc/
 
 SPECIALIX IO8+ MULTIPORT SERIAL CARD DRIVER
-P:	Roger Wolff
-M:	R.E.Wolff@BitWizard.nl
+M:	Roger Wolff <R.E.Wolff@BitWizard.nl>
 S:	Supported
 F:	Documentation/serial/specialix.txt
 F:	drivers/char/specialix*
 
 SPI SUBSYSTEM
-P:	David Brownell
-M:	dbrownell@users.sourceforge.net
+M:	David Brownell <dbrownell@users.sourceforge.net>
 L:	spi-devel-general@lists.sourceforge.net
 S:	Maintained
 F:	Documentation/spi/
@@ -5518,18 +4756,15 @@ F:	drivers/spi/
 F:	include/linux/spi/
 
 SPIDERNET NETWORK DRIVER for CELL
-P:	Ishizaki Kou
-M:	kou.ishizaki@toshiba.co.jp
-P:	Jens Osterkamp
-M:	jens@de.ibm.com
+M:	Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
+M:	Jens Osterkamp <jens@de.ibm.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	Documentation/networking/spider_net.txt
 F:	drivers/net/spider_net*
 
 SPU FILE SYSTEM
-P:	Jeremy Kerr
-M:	jk@ozlabs.org
+M:	Jeremy Kerr <jk@ozlabs.org>
 L:	linuxppc-dev@ozlabs.org
 L:	cbe-oss-dev@ozlabs.org
 W:	http://www.ibm.com/developerworks/power/cell/
@@ -5538,8 +4773,7 @@ F:	Documentation/filesystems/spufs.txt
 F:	arch/powerpc/platforms/cell/spufs/
 
 SQUASHFS FILE SYSTEM
-P:	Phillip Lougher
-M:	phillip@lougher.demon.co.uk
+M:	Phillip Lougher <phillip@lougher.demon.co.uk>
 L:	squashfs-devel@lists.sourceforge.net (subscribers-only)
 W:	http://squashfs.org.uk
 S:	Maintained
@@ -5547,30 +4781,25 @@ F:	Documentation/filesystems/squashfs.txt
 F:	fs/squashfs/
 
 SRM (Alpha) environment access
-P:	Jan-Benedict Glaw
-M:	jbglaw@lug-owl.de
+M:	Jan-Benedict Glaw <jbglaw@lug-owl.de>
 S:	Maintained
 F:	arch/alpha/kernel/srm_env.c
 
 STABLE BRANCH
-P:	Greg Kroah-Hartman
-M:	greg@kroah.com
-P:	Chris Wright
-M:	chrisw@sous-sol.org
+M:	Greg Kroah-Hartman <greg@kroah.com>
+M:	Chris Wright <chrisw@sous-sol.org>
 L:	stable@kernel.org
 S:	Maintained
 
 STAGING SUBSYSTEM
-P:	Greg Kroah-Hartman
-M:	gregkh@suse.de
+M:	Greg Kroah-Hartman <gregkh@suse.de>
 T:	quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/
 L:	devel@driverdev.osuosl.org
 S:	Maintained
 F:	drivers/staging/
 
 STARFIRE/DURALAN NETWORK DRIVER
-P:	Ion Badulescu
-M:	ionut@badula.org
+M:	Ion Badulescu <ionut@badula.org>
 S:	Odd Fixes
 F:	drivers/net/starfire*
 
@@ -5580,15 +4809,13 @@ F:	drivers/net/wireless/strip.c
 F:	include/linux/if_strip.h
 
 STRADIS MPEG-2 DECODER DRIVER
-P:	Nathan Laredo
-M:	laredo@gnu.org
+M:	Nathan Laredo <laredo@gnu.org>
 W:	http://www.stradis.com/
 S:	Maintained
 F:	drivers/media/video/stradis.c
 
 SUN3/3X
-P:	Sam Creasey
-M:	sammy@sammy.net
+M:	Sam Creasey <sammy@sammy.net>
 W:	http://sammy.net/sun3/
 S:	Maintained
 F:	arch/m68k/kernel/*sun3*
@@ -5596,8 +4823,7 @@ F:	arch/m68k/sun3*/
 F:	arch/m68k/include/asm/sun3*
 
 SUPERH
-P:	Paul Mundt
-M:	lethal@linux-sh.org
+M:	Paul Mundt <lethal@linux-sh.org>
 L:	linux-sh@vger.kernel.org
 W:	http://www.linux-sh.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.git
@@ -5607,12 +4833,9 @@ F:	arch/sh/
 F:	drivers/sh/
 
 SUSPEND TO RAM
-P:	Len Brown
-M:	len.brown@intel.com
-P:	Pavel Machek
-M:	pavel@ucw.cz
-P:	Rafael J. Wysocki
-M:	rjw@sisk.pl
+M:	Len Brown <len.brown@intel.com>
+M:	Pavel Machek <pavel@ucw.cz>
+M:	"Rafael J. Wysocki" <rjw@sisk.pl>
 L:	linux-pm@lists.linux-foundation.org
 S:	Supported
 F:	Documentation/power/
@@ -5624,32 +4847,28 @@ F:	include/linux/freezer.h
 F:	include/linux/pm.h
 
 SVGA HANDLING
-P:	Martin Mares
-M:	mj@ucw.cz
+M:	Martin Mares <mj@ucw.cz>
 L:	linux-video@atrey.karlin.mff.cuni.cz
 S:	Maintained
 F:	Documentation/svga.txt
 F:	arch/x86/boot/video*
 
 SYSV FILESYSTEM
-P:	Christoph Hellwig
-M:	hch@infradead.org
+M:	Christoph Hellwig <hch@infradead.org>
 S:	Maintained
 F:	Documentation/filesystems/sysv-fs.txt
 F:	fs/sysv/
 F:	include/linux/sysv_fs.h
 
 TASKSTATS STATISTICS INTERFACE
-P:	Balbir Singh
-M:	balbir@linux.vnet.ibm.com
+M:	Balbir Singh <balbir@linux.vnet.ibm.com>
 S:	Maintained
 F:	Documentation/accounting/taskstats*
 F:	include/linux/taskstats*
 F:	kernel/taskstats.c
 
 TC CLASSIFIER
-P:	Jamal Hadi Salim
-M:	hadi@cyberus.ca
+M:	Jamal Hadi Salim <hadi@cyberus.ca>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	include/linux/pkt_cls.h
@@ -5657,38 +4876,31 @@ F:	include/net/pkt_cls.h
 F:	net/sched/
 
 TCP LOW PRIORITY MODULE
-P:	Wong Hoi Sing, Edison
-M:	hswong3i@gmail.com
-P:	Hung Hing Lun, Mike
-M:	hlhung3i@gmail.com
+M:	"Wong Hoi Sing, Edison" <hswong3i@gmail.com>
+M:	"Hung Hing Lun, Mike" <hlhung3i@gmail.com>
 W:	http://tcp-lp-mod.sourceforge.net/
 S:	Maintained
 F:	net/ipv4/tcp_lp.c
 
 TEHUTI ETHERNET DRIVER
-P:	Alexander Indenbaum
-M:	baum@tehutinetworks.net
-P:	Andy Gospodarek
-M:	andy@greyhouse.net
+M:	Alexander Indenbaum <baum@tehutinetworks.net>
+M:	Andy Gospodarek <andy@greyhouse.net>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/tehuti*
 
 Telecom Clock Driver for MCPL0010
-P:	Mark Gross
-M:	mark.gross@intel.com
+M:	Mark Gross <mark.gross@intel.com>
 S:	Supported
 F:	drivers/char/tlclk.c
 
 TENSILICA XTENSA PORT (xtensa)
-P:	Chris Zankel
-M:	chris@zankel.net
+M:	Chris Zankel <chris@zankel.net>
 S:	Maintained
 F:	arch/xtensa/
 
 THINKPAD ACPI EXTRAS DRIVER
-P:	Henrique de Moraes Holschuh
-M:	ibm-acpi@hmh.eng.br
+M:	Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br>
 L:	ibm-acpi-devel@lists.sourceforge.net
 W:	http://ibm-acpi.sourceforge.net
 W:	http://thinkwiki.org/wiki/Ibm-acpi
@@ -5697,27 +4909,22 @@ S:	Maintained
 F:	drivers/platform/x86/thinkpad_acpi.c
 
 TI FLASH MEDIA INTERFACE DRIVER
-P:	Alex Dubov
-M:	oakad@yahoo.com
+M:	Alex Dubov <oakad@yahoo.com>
 S:	Maintained
 F:	drivers/misc/tifm*
 F:	drivers/mmc/host/tifm_sd.c
 F:	include/linux/tifm.h
 
 TI TWL4030 SERIES SOC CODEC DRIVER
-P:	Peter Ujfalusi
-M:	peter.ujfalusi@nokia.com
+M:	Peter Ujfalusi <peter.ujfalusi@nokia.com>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 S:	Maintained
 F:	sound/soc/codecs/twl4030*
 
 TIPC NETWORK LAYER
-P:	Per Liden
-M:	per.liden@ericsson.com
-P:	Jon Maloy
-M:	jon.maloy@ericsson.com
-P:	Allan Stephens
-M:	allan.stephens@windriver.com
+M:	Per Liden <per.liden@ericsson.com>
+M:	Jon Maloy <jon.maloy@ericsson.com>
+M:	Allan Stephens <allan.stephens@windriver.com>
 L:	tipc-discussion@lists.sourceforge.net
 W:	http://tipc.sourceforge.net/
 W:	http://tipc.cslab.ericsson.net/
@@ -5728,8 +4935,7 @@ F:	include/net/tipc/
 F:	net/tipc/
 
 TLAN NETWORK DRIVER
-P:	Samuel Chessman
-M:	chessman@tux.org
+M:	Samuel Chessman <chessman@tux.org>
 L:	tlan-devel@lists.sourceforge.net (subscribers-only)
 W:	http://sourceforge.net/projects/tlan/
 S:	Maintained
@@ -5737,10 +4943,8 @@ F:	Documentation/networking/tlan.txt
 F:	drivers/net/tlan.*
 
 TOMOYO SECURITY MODULE
-P:	Kentaro Takeda
-M:	takedakn@nttdata.co.jp
-P:	Tetsuo Handa
-M:	penguin-kernel@I-love.SAKURA.ne.jp
+M:	Kentaro Takeda <takedakn@nttdata.co.jp>
+M:	Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
 L:	tomoyo-users-en@lists.sourceforge.jp (subscribers-only, for developers and users in English)
 L:	tomoyo-dev@lists.sourceforge.jp (subscribers-only, for developers in Japanese)
 L:	tomoyo-users@lists.sourceforge.jp (subscribers-only, for users in Japanese)
@@ -5754,8 +4958,7 @@ S:	Orphan
 F:	drivers/platform/x86/toshiba_acpi.c
 
 TOSHIBA SMM DRIVER
-P:	Jonathan Buzzard
-M:	jonathan@buzzard.org.uk
+M:	Jonathan Buzzard <jonathan@buzzard.org.uk>
 L:	tlinux-users@tce.toshiba-dme.co.jp
 W:	http://www.buzzard.org.uk/toshiba/
 S:	Maintained
@@ -5763,41 +4966,34 @@ F:	drivers/char/toshiba.c
 F:	include/linux/toshiba.h
 
 TMIO MMC DRIVER
-P:	Ian Molton
-M:	ian@mnementh.co.uk
+M:	Ian Molton <ian@mnementh.co.uk>
 S:	Maintained
 F:	drivers/mmc/host/tmio_mmc.*
 
 TMPFS (SHMEM FILESYSTEM)
-P:	Hugh Dickins
-M:	hugh.dickins@tiscali.co.uk
+M:	Hugh Dickins <hugh.dickins@tiscali.co.uk>
 L:	linux-mm@kvack.org
 S:	Maintained
 F:	include/linux/shmem_fs.h
 F:	mm/shmem.c
 
 TPM DEVICE DRIVER
-P:	Debora Velarde
-M:	debora@linux.vnet.ibm.com
-P:	Rajiv Andrade
-M:	srajiv@linux.vnet.ibm.com
+M:	Debora Velarde <debora@linux.vnet.ibm.com>
+M:	Rajiv Andrade <srajiv@linux.vnet.ibm.com>
 W:	http://tpmdd.sourceforge.net
-P:	Marcel Selhorst
-M:	m.selhorst@sirrix.com
+M:	Marcel Selhorst <m.selhorst@sirrix.com>
 W:	http://www.sirrix.com
 L:	tpmdd-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/char/tpm/
 
 TRIVIAL PATCHES
-P:	Jiri Kosina
-M:	trivial@kernel.org
+M:	Jiri Kosina <trivial@kernel.org>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial.git
 S:	Maintained
 
 TTY LAYER
-P:	Alan Cox
-M:	alan@lxorguk.ukuu.org.uk
+M:	Alan Cox <alan@lxorguk.ukuu.org.uk>
 S:	Maintained
 T:	stgit http://zeniv.linux.org.uk/~alan/ttydev/
 F:	drivers/char/tty_*
@@ -5807,17 +5003,14 @@ F:	include/linux/serial.h
 F:	include/linux/tty.h
 
 TULIP NETWORK DRIVERS
-P:	Grant Grundler
-M:	grundler@parisc-linux.org
-P:	Kyle McMartin
-M:	kyle@mcmartin.ca
+M:	Grant Grundler <grundler@parisc-linux.org>
+M:	Kyle McMartin <kyle@mcmartin.ca>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/tulip/
 
 TUN/TAP driver
-P:	Maxim Krasnyansky
-M:	maxk@qualcomm.com
+M:	Maxim Krasnyansky <maxk@qualcomm.com>
 L:	vtun@office.satix.net
 W:	http://vtun.sourceforge.net/tun
 S:	Maintained
@@ -5825,24 +5018,20 @@ F:	Documentation/networking/tuntap.txt
 F:	arch/um/os-Linux/drivers/
 
 TURBOCHANNEL SUBSYSTEM
-P:	Maciej W. Rozycki
-M:	macro@linux-mips.org
+M:	"Maciej W. Rozycki" <macro@linux-mips.org>
 S:	Maintained
 F:	drivers/tc/
 F:	include/linux/tc.h
 
 U14-34F SCSI DRIVER
-P:	Dario Ballabio
-M:	ballabio_dario@emc.com
+M:	Dario Ballabio <ballabio_dario@emc.com>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/u14-34f.c
 
 UBI FILE SYSTEM (UBIFS)
-P:	Artem Bityutskiy
-M:	dedekind@infradead.org
-P:	Adrian Hunter
-M:	adrian.hunter@nokia.com
+M:	Artem Bityutskiy <dedekind@infradead.org>
+M:	Adrian Hunter <adrian.hunter@nokia.com>
 L:	linux-mtd@lists.infradead.org
 T:	git git://git.infradead.org/ubifs-2.6.git
 W:	http://www.linux-mtd.infradead.org/doc/ubifs.html
@@ -5851,37 +5040,32 @@ F:	Documentation/filesystems/ubifs.txt
 F:	fs/ubifs/
 
 UCLINUX (AND M68KNOMMU)
-P:	Greg Ungerer
-M:	gerg@uclinux.org
+M:	Greg Ungerer <gerg@uclinux.org>
 W:	http://www.uclinux.org/
 L:	uclinux-dev@uclinux.org  (subscribers-only)
 S:	Maintained
 F:	arch/m68knommu/
 
 UCLINUX FOR RENESAS H8/300 (H8300)
-P:	Yoshinori Sato
-M:	ysato@users.sourceforge.jp
+M:	Yoshinori Sato <ysato@users.sourceforge.jp>
 W:	http://uclinux-h8.sourceforge.jp/
 S:	Supported
 
 UDF FILESYSTEM
-P:	Jan Kara
-M:	jack@suse.cz
+M:	Jan Kara <jack@suse.cz>
 W:	http://linux-udf.sourceforge.net
 S:	Maintained
 F:	Documentation/filesystems/udf.txt
 F:	fs/udf/
 
 UFS FILESYSTEM
-P:	Evgeniy Dushistov
-M:	dushistov@mail.ru
+M:	Evgeniy Dushistov <dushistov@mail.ru>
 S:	Maintained
 F:	Documentation/filesystems/ufs.txt
 F:	fs/ufs/
 
 ULTRA-WIDEBAND (UWB) SUBSYSTEM:
-P:	David Vrabel
-M:	david.vrabel@csr.com
+M:	David Vrabel <david.vrabel@csr.com>
 L:	linux-usb@vger.kernel.org
 S:	Supported
 F:	drivers/uwb/*
@@ -5889,8 +5073,7 @@ F:	include/linux/uwb.h
 F:	include/linux/uwb/
 
 UNIFORM CDROM DRIVER
-P:	Jens Axboe
-M:	axboe@kernel.dk
+M:	Jens Axboe <axboe@kernel.dk>
 W:	http://www.kernel.dk
 S:	Maintained
 F:	Documentation/cdrom/
@@ -5898,8 +5081,7 @@ F:	drivers/cdrom/cdrom.c
 F:	include/linux/cdrom.h
 
 UNSORTED BLOCK IMAGES (UBI)
-P:	Artem Bityutskiy
-M:	dedekind@infradead.org
+M:	Artem Bityutskiy <dedekind@infradead.org>
 W:	http://www.linux-mtd.infradead.org/
 L:	linux-mtd@lists.infradead.org
 T:	git git://git.infradead.org/ubi-2.6.git
@@ -5909,23 +5091,20 @@ F:	include/linux/mtd/ubi.h
 F:	include/mtd/ubi-user.h
 
 USB ACM DRIVER
-P:	Oliver Neukum
-M:	oliver@neukum.name
+M:	Oliver Neukum <oliver@neukum.name>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	Documentation/usb/acm.txt
 F:	drivers/usb/class/cdc-acm.*
 
 USB BLOCK DRIVER (UB ub)
-P:	Pete Zaitcev
-M:	zaitcev@redhat.com
+M:	Pete Zaitcev <zaitcev@redhat.com>
 L:	linux-usb@vger.kernel.org
 S:	Supported
 F:	drivers/block/ub.c
 
 USB CDC ETHERNET DRIVER
-P:	Greg Kroah-Hartman
-M:	greg@kroah.com
+M:	Greg Kroah-Hartman <greg@kroah.com>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 W:	http://www.kroah.com/linux-usb/
@@ -5933,39 +5112,34 @@ F:	drivers/net/usb/cdc_*.c
 F:	include/linux/usb/cdc.h
 
 USB CYPRESS C67X00 DRIVER
-P:	Peter Korsgaard
-M:	jacmet@sunsite.dk
+M:	Peter Korsgaard <jacmet@sunsite.dk>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/c67x00/
 
 USB DAVICOM DM9601 DRIVER
-P:	Peter Korsgaard
-M:	jacmet@sunsite.dk
+M:	Peter Korsgaard <jacmet@sunsite.dk>
 L:	netdev@vger.kernel.org
 W:	http://www.linux-usb.org/usbnet
 S:	Maintained
 F:	drivers/net/usb/dm9601.c
 
 USB DIAMOND RIO500 DRIVER
-P:	Cesar Miquel
-M:	miquel@df.uba.ar
+M:	Cesar Miquel <miquel@df.uba.ar>
 L:	rio500-users@lists.sourceforge.net
 W:	http://rio500.sourceforge.net
 S:	Maintained
 F:	drivers/usb/misc/rio500*
 
 USB EHCI DRIVER
-P:	David Brownell
-M:	dbrownell@users.sourceforge.net
+M:	David Brownell <dbrownell@users.sourceforge.net>
 L:	linux-usb@vger.kernel.org
 S:	Odd Fixes
 F:	Documentation/usb/ehci.txt
 F:	drivers/usb/host/ehci*
 
 USB ET61X[12]51 DRIVER
-P:	Luca Risolia
-M:	luca.risolia@studio.unibo.it
+M:	Luca Risolia <luca.risolia@studio.unibo.it>
 L:	linux-usb@vger.kernel.org
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
@@ -5974,8 +5148,7 @@ S:	Maintained
 F:	drivers/media/video/et61x251/
 
 USB GADGET/PERIPHERAL SUBSYSTEM
-P:	David Brownell
-M:	dbrownell@users.sourceforge.net
+M:	David Brownell <dbrownell@users.sourceforge.net>
 L:	linux-usb@vger.kernel.org
 W:	http://www.linux-usb.org/gadget
 S:	Maintained
@@ -5983,8 +5156,7 @@ F:	drivers/usb/gadget/
 F:	include/linux/usb/gadget*
 
 USB HID/HIDBP DRIVERS (USB KEYBOARDS, MICE, REMOTE CONTROLS, ...)
-P:	Jiri Kosina
-M:	jkosina@suse.cz
+M:	Jiri Kosina <jkosina@suse.cz>
 L:	linux-usb@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid.git
 S:	Maintained
@@ -5992,23 +5164,20 @@ F:	Documentation/usb/hiddev.txt
 F:	drivers/hid/usbhid/
 
 USB ISP116X DRIVER
-P:	Olav Kongas
-M:	ok@artecdesign.ee
+M:	Olav Kongas <ok@artecdesign.ee>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/host/isp116x*
 F:	include/linux/usb/isp116x.h
 
 USB KAWASAKI LSI DRIVER
-P:	Oliver Neukum
-M:	oliver@neukum.name
+M:	Oliver Neukum <oliver@neukum.name>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/serial/kl5kusb105.*
 
 USB MASS STORAGE DRIVER
-P:	Matthew Dharm
-M:	mdharm-usb@one-eyed-alien.net
+M:	Matthew Dharm <mdharm-usb@one-eyed-alien.net>
 L:	linux-usb@vger.kernel.org
 L:	usb-storage@lists.one-eyed-alien.net
 S:	Maintained
@@ -6016,31 +5185,27 @@ W:	http://www.one-eyed-alien.net/~mdharm/linux-usb/
 F:	drivers/usb/storage/
 
 USB OHCI DRIVER
-P:	David Brownell
-M:	dbrownell@users.sourceforge.net
+M:	David Brownell <dbrownell@users.sourceforge.net>
 L:	linux-usb@vger.kernel.org
 S:	Odd Fixes
 F:	Documentation/usb/ohci.txt
 F:	drivers/usb/host/ohci*
 
 USB OPTION-CARD DRIVER
-P:	Matthias Urlichs
-M:	smurf@smurf.noris.de
+M:	Matthias Urlichs <smurf@smurf.noris.de>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/serial/option.c
 
 USB OV511 DRIVER
-P:	Mark McClelland
-M:	mmcclell@bigfoot.com
+M:	Mark McClelland <mmcclell@bigfoot.com>
 L:	linux-usb@vger.kernel.org
 W:	http://alpha.dyndns.org/ov511/
 S:	Maintained
 F:	drivers/media/video/ov511.*
 
 USB PEGASUS DRIVER
-P:	Petko Manolov
-M:	petkan@users.sourceforge.net
+M:	Petko Manolov <petkan@users.sourceforge.net>
 L:	linux-usb@vger.kernel.org
 L:	netdev@vger.kernel.org
 W:	http://pegasus2.sourceforge.net/
@@ -6048,15 +5213,13 @@ S:	Maintained
 F:	drivers/net/usb/pegasus.*
 
 USB PRINTER DRIVER (usblp)
-P:	Pete Zaitcev
-M:	zaitcev@redhat.com
+M:	Pete Zaitcev <zaitcev@redhat.com>
 L:	linux-usb@vger.kernel.org
 S:	Supported
 F:	drivers/usb/class/usblp.c
 
 USB RTL8150 DRIVER
-P:	Petko Manolov
-M:	petkan@users.sourceforge.net
+M:	Petko Manolov <petkan@users.sourceforge.net>
 L:	linux-usb@vger.kernel.org
 L:	netdev@vger.kernel.org
 W:	http://pegasus2.sourceforge.net/
@@ -6064,8 +5227,7 @@ S:	Maintained
 F:	drivers/net/usb/rtl8150.c
 
 USB SE401 DRIVER
-P:	Jeroen Vreeken
-M:	pe1rxq@amsat.org
+M:	Jeroen Vreeken <pe1rxq@amsat.org>
 L:	linux-usb@vger.kernel.org
 W:	http://www.chello.nl/~j.vreeken/se401/
 S:	Maintained
@@ -6073,15 +5235,13 @@ F:	Documentation/video4linux/se401.txt
 F:	drivers/media/video/se401.*
 
 USB SERIAL BELKIN F5U103 DRIVER
-P:	William Greathouse
-M:	wgreathouse@smva.com
+M:	William Greathouse <wgreathouse@smva.com>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/serial/belkin_sa.*
 
 USB SERIAL CYPRESS M8 DRIVER
-P:	Lonnie Mendez
-M:	dignome@gmail.com
+M:	Lonnie Mendez <dignome@gmail.com>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 W:	http://geocities.com/i0xox0i
@@ -6089,24 +5249,20 @@ W:	http://firstlight.net/cvs
 F:	drivers/usb/serial/cypress_m8.*
 
 USB SERIAL CYBERJACK DRIVER
-P:	Matthias Bruestle and Harald Welte
-M:	support@reiner-sct.com
+M:	Matthias Bruestle and Harald Welte <support@reiner-sct.com>
 W:	http://www.reiner-sct.de/support/treiber_cyberjack.php
 S:	Maintained
 F:	drivers/usb/serial/cyberjack.c
 
 USB SERIAL DIGI ACCELEPORT DRIVER
-P:	Peter Berger
-M:	pberger@brimson.com
-P:	Al Borchers
-M:	alborchers@steinerpoint.com
+M:	Peter Berger <pberger@brimson.com>
+M:	Al Borchers <alborchers@steinerpoint.com>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/serial/digi_acceleport.c
 
 USB SERIAL DRIVER
-P:	Greg Kroah-Hartman
-M:	gregkh@suse.de
+M:	Greg Kroah-Hartman <gregkh@suse.de>
 L:	linux-usb@vger.kernel.org
 S:	Supported
 F:	Documentation/usb/usb-serial.txt
@@ -6115,38 +5271,33 @@ F:	drivers/usb/serial/usb-serial.c
 F:	include/linux/usb/serial.h
 
 USB SERIAL EMPEG EMPEG-CAR MARK I/II DRIVER
-P:	Gary Brubaker
-M:	xavyer@ix.netcom.com
+M:	Gary Brubaker <xavyer@ix.netcom.com>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/serial/empeg.c
 
 USB SERIAL KEYSPAN DRIVER
-P:	Greg Kroah-Hartman
-M:	greg@kroah.com
+M:	Greg Kroah-Hartman <greg@kroah.com>
 L:	linux-usb@vger.kernel.org
 W:	http://www.kroah.com/linux/
 S:	Maintained
 F:	drivers/usb/serial/*keyspan*
 
 USB SERIAL WHITEHEAT DRIVER
-P:	Support Department
-M:	support@connecttech.com
+M:	Support Department <support@connecttech.com>
 L:	linux-usb@vger.kernel.org
 W:	http://www.connecttech.com
 S:	Supported
 F:	drivers/usb/serial/whiteheat*
 
 USB SMSC95XX ETHERNET DRIVER
-P:	Steve Glendinning
-M:	steve.glendinning@smsc.com
+M:	Steve Glendinning <steve.glendinning@smsc.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/usb/smsc95xx.*
 
 USB SN9C1xx DRIVER
-P:	Luca Risolia
-M:	luca.risolia@studio.unibo.it
+M:	Luca Risolia <luca.risolia@studio.unibo.it>
 L:	linux-usb@vger.kernel.org
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
@@ -6156,8 +5307,7 @@ F:	Documentation/video4linux/sn9c102.txt
 F:	drivers/media/video/sn9c102/
 
 USB SUBSYSTEM
-P:	Greg Kroah-Hartman
-M:	gregkh@suse.de
+M:	Greg Kroah-Hartman <gregkh@suse.de>
 L:	linux-usb@vger.kernel.org
 W:	http://www.linux-usb.org
 T:	quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/
@@ -6169,15 +5319,13 @@ F:	include/linux/usb.h
 F:	include/linux/usb/
 
 USB UHCI DRIVER
-P:	Alan Stern
-M:	stern@rowland.harvard.edu
+M:	Alan Stern <stern@rowland.harvard.edu>
 L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/host/uhci*
 
 USB "USBNET" DRIVER FRAMEWORK
-P:	David Brownell
-M:	dbrownell@users.sourceforge.net
+M:	David Brownell <dbrownell@users.sourceforge.net>
 L:	netdev@vger.kernel.org
 W:	http://www.linux-usb.org/usbnet
 S:	Maintained
@@ -6185,8 +5333,7 @@ F:	drivers/net/usb/usbnet.c
 F:	include/linux/usb/usbnet.h
 
 USB VIDEO CLASS
-P:	Laurent Pinchart
-M:	laurent.pinchart@skynet.be
+M:	Laurent Pinchart <laurent.pinchart@skynet.be>
 L:	linux-uvc-devel@lists.berlios.de (subscribers-only)
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
@@ -6195,8 +5342,7 @@ S:	Maintained
 F:	drivers/media/video/uvc/
 
 USB W996[87]CF DRIVER
-P:	Luca Risolia
-M:	luca.risolia@studio.unibo.it
+M:	Luca Risolia <luca.risolia@studio.unibo.it>
 L:	linux-usb@vger.kernel.org
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
@@ -6206,21 +5352,18 @@ F:	Documentation/video4linux/w9968cf.txt
 F:	drivers/media/video/w996*
 
 USB WIRELESS RNDIS DRIVER (rndis_wlan)
-P:	Jussi Kivilinna
-M:	jussi.kivilinna@mbnet.fi
+M:	Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
 L:	linux-wireless@vger.kernel.org
 S:	Maintained
 F:	drivers/net/wireless/rndis_wlan.c
 
 USB XHCI DRIVER
-P:	Sarah Sharp
-M:	sarah.a.sharp@intel.com
+M:	Sarah Sharp <sarah.a.sharp@intel.com>
 L:	linux-usb@vger.kernel.org
 S:	Supported
 
 USB ZC0301 DRIVER
-P:	Luca Risolia
-M:	luca.risolia@studio.unibo.it
+M:	Luca Risolia <luca.risolia@studio.unibo.it>
 L:	linux-usb@vger.kernel.org
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
@@ -6230,16 +5373,14 @@ F:	Documentation/video4linux/zc0301.txt
 F:	drivers/media/video/zc0301/
 
 USB ZD1201 DRIVER
-P:	Jeroen Vreeken
-M:	pe1rxq@amsat.org
+M:	Jeroen Vreeken <pe1rxq@amsat.org>
 L:	linux-usb@vger.kernel.org
 W:	http://linux-lc100020.sourceforge.net
 S:	Maintained
 F:	drivers/net/wireless/zd1201.*
 
 USB ZR364XX DRIVER
-P:	Antoine Jacquet
-M:	royale@zerezo.com
+M:	Antoine Jacquet <royale@zerezo.com>
 L:	linux-usb@vger.kernel.org
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
@@ -6249,8 +5390,7 @@ F:	Documentation/video4linux/zr364xx.txt
 F:	drivers/media/video/zr364xx.c
 
 USER-MODE LINUX (UML)
-P:	Jeff Dike
-M:	jdike@addtoit.com
+M:	Jeff Dike <jdike@addtoit.com>
 L:	user-mode-linux-devel@lists.sourceforge.net
 L:	user-mode-linux-user@lists.sourceforge.net
 W:	http://user-mode-linux.sourceforge.net
@@ -6261,26 +5401,22 @@ F:	fs/hostfs/
 F:	fs/hppfs/
 
 USERSPACE I/O (UIO)
-P:	Hans J. Koch
-M:	hjk@linutronix.de
-P:	Greg Kroah-Hartman
-M:	gregkh@suse.de
+M:	"Hans J. Koch" <hjk@linutronix.de>
+M:	Greg Kroah-Hartman <gregkh@suse.de>
 S:	Maintained
 F:	Documentation/DocBook/uio-howto.tmpl
 F:	drivers/uio/
 F:	include/linux/uio*.h
 
 UTIL-LINUX-NG PACKAGE
-P:	Karel Zak
-M:	kzak@redhat.com
+M:	Karel Zak <kzak@redhat.com>
 L:	util-linux-ng@vger.kernel.org
 W:	http://kernel.org/~kzak/util-linux-ng/
 T:	git git://git.kernel.org/pub/scm/utils/util-linux-ng/util-linux-ng.git
 S:	Maintained
 
 UVESAFB DRIVER
-P:	Michal Januszewski
-M:	spock@gentoo.org
+M:	Michal Januszewski <spock@gentoo.org>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	http://dev.gentoo.org/~spock/projects/uvesafb/
 S:	Maintained
@@ -6288,53 +5424,44 @@ F:	Documentation/fb/uvesafb.txt
 F:	drivers/video/uvesafb.*
 
 VFAT/FAT/MSDOS FILESYSTEM
-P:	OGAWA Hirofumi
-M:	hirofumi@mail.parknet.co.jp
+M:	OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
 S:	Maintained
 F:	Documentation/filesystems/vfat.txt
 F:	fs/fat/
 
 VIA RHINE NETWORK DRIVER
-P:	Roger Luethi
-M:	rl@hellgate.ch
+M:	Roger Luethi <rl@hellgate.ch>
 S:	Maintained
 F:	drivers/net/via-rhine.c
 
 VIAPRO SMBUS DRIVER
-P:	Jean Delvare
-M:	khali@linux-fr.org
+M:	Jean Delvare <khali@linux-fr.org>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	Documentation/i2c/busses/i2c-viapro
 F:	drivers/i2c/busses/i2c-viapro.c
 
 VIA SD/MMC CARD CONTROLLER DRIVER
-P:	Joseph Chan
-M:	JosephChan@via.com.tw
-P:	Harald Welte
-M:	HaraldWelte@viatech.com
+M:	Joseph Chan <JosephChan@via.com.tw>
+M:	Harald Welte <HaraldWelte@viatech.com>
 S:	Maintained
 F:	drivers/mmc/host/via-sdmmc.c
 
 VIA UNICHROME(PRO)/CHROME9 FRAMEBUFFER DRIVER
-P:	Joseph Chan
-M:	JosephChan@via.com.tw
-P:	Scott Fang
-M:	ScottFang@viatech.com.cn
+M:	Joseph Chan <JosephChan@via.com.tw>
+M:	Scott Fang <ScottFang@viatech.com.cn>
 L:	linux-fbdev-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 F:	drivers/video/via/
 
 VIA VELOCITY NETWORK DRIVER
-P:	Francois Romieu
-M:	romieu@fr.zoreil.com
+M:	Francois Romieu <romieu@fr.zoreil.com>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/via-velocity.*
 
 VLAN (802.1Q)
-P:	Patrick McHardy
-M:	kaber@trash.net
+M:	Patrick McHardy <kaber@trash.net>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/macvlan.c
@@ -6342,18 +5469,15 @@ F:	include/linux/if_*vlan.h
 F:	net/8021q/
 
 VLYNQ BUS
-P:	Florian Fainelli
-M:	florian@openwrt.org
+M:	Florian Fainelli <florian@openwrt.org>
 L:	openwrt-devel@lists.openwrt.org
 S:	Maintained
 F:	drivers/vlynq/vlynq.c
 F:	include/linux/vlynq.h
 
 VOLTAGE AND CURRENT REGULATOR FRAMEWORK
-P:	Liam Girdwood
-M:	lrg@slimlogic.co.uk
-P:	Mark Brown
-M:	broonie@opensource.wolfsonmicro.com
+M:	Liam Girdwood <lrg@slimlogic.co.uk>
+M:	Mark Brown <broonie@opensource.wolfsonmicro.com>
 W:	http://opensource.wolfsonmicro.com/node/15
 W:	http://www.slimlogic.co.uk/?p=48
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6.git
@@ -6362,52 +5486,45 @@ F:	drivers/regulator/
 F:	include/linux/regulator/
 
 VT1211 HARDWARE MONITOR DRIVER
-P:	Juerg Haefliger
-M:	juergh@gmail.com
+M:	Juerg Haefliger <juergh@gmail.com>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/vt1211
 F:	drivers/hwmon/vt1211.c
 
 VT8231 HARDWARE MONITOR DRIVER
-P:	Roger Lucas
-M:	vt8231@hiddenengine.co.uk
+M:	Roger Lucas <vt8231@hiddenengine.co.uk>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	drivers/hwmon/vt8231.c
 
 W1 DALLAS'S 1-WIRE BUS
-P:	Evgeniy Polyakov
-M:	johnpol@2ka.mipt.ru
+M:	Evgeniy Polyakov <johnpol@2ka.mipt.ru>
 S:	Maintained
 F:	Documentation/w1/
 F:	drivers/w1/
 
 W83791D HARDWARE MONITORING DRIVER
-P:	Marc Hulsman
-M:	m.hulsman@tudelft.nl
+M:	Marc Hulsman <m.hulsman@tudelft.nl>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/w83791d
 F:	drivers/hwmon/w83791d.c
 
 W83793 HARDWARE MONITORING DRIVER
-P:	Rudolf Marek
-M:	r.marek@assembler.cz
+M:	Rudolf Marek <r.marek@assembler.cz>
 L:	lm-sensors@lm-sensors.org
 S:	Maintained
 F:	Documentation/hwmon/w83793
 F:	drivers/hwmon/w83793.c
 
 W83L51xD SD/MMC CARD INTERFACE DRIVER
-P:	Pierre Ossman
-M:	pierre@ossman.eu
+M:	Pierre Ossman <pierre@ossman.eu>
 S:	Maintained
 F:	drivers/mmc/host/wbsd.*
 
 WATCHDOG DEVICE DRIVERS
-P:	Wim Van Sebroeck
-M:	wim@iguana.be
+M:	Wim Van Sebroeck <wim@iguana.be>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog.git
 S:	Maintained
 F:	Documentation/watchdog/
@@ -6415,8 +5532,7 @@ F:	drivers/watchdog/
 F:	include/linux/watchdog.h
 
 WAVELAN NETWORK DRIVER & WIRELESS EXTENSIONS
-P:	Jean Tourrilhes
-M:	jt@hpl.hp.com
+M:	Jean Tourrilhes <jt@hpl.hp.com>
 L:	linux-wireless@vger.kernel.org
 W:	http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/
 S:	Maintained
@@ -6424,46 +5540,39 @@ F:	Documentation/networking/wavelan.txt
 F:	drivers/net/wireless/wavelan*
 
 WD7000 SCSI DRIVER
-P:	Miroslav Zagorac
-M:	zaga@fly.cc.fer.hr
+M:	Miroslav Zagorac <zaga@fly.cc.fer.hr>
 L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/wd7000.c
 
 WIMAX STACK
-P:	Inaky Perez-Gonzalez
-M:	inaky.perez-gonzalez@intel.com
+M:	Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
 M:	linux-wimax@intel.com
 L:	wimax@linuxwimax.org
 S:	Supported
 W:	http://linuxwimax.org
 
 WIMEDIA LLC PROTOCOL (WLP) SUBSYSTEM
-P:	David Vrabel
-M:	david.vrabel@csr.com
+M:	David Vrabel <david.vrabel@csr.com>
 S:	Maintained
 F:	include/linux/wlp.h
 F:	drivers/uwb/wlp/
 
 WISTRON LAPTOP BUTTON DRIVER
-P:	Miloslav Trmac
-M:	mitr@volny.cz
+M:	Miloslav Trmac <mitr@volny.cz>
 S:	Maintained
 F:	drivers/input/misc/wistron_btns.c
 
 WL3501 WIRELESS PCMCIA CARD DRIVER
-P:	Arnaldo Carvalho de Melo
-M:	acme@ghostprotocols.net
+M:	Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
 L:	linux-wireless@vger.kernel.org
 W:	http://oops.ghostprotocols.net:81/blog
 S:	Maintained
 F:	drivers/net/wireless/wl3501*
 
 WM97XX TOUCHSCREEN DRIVERS
-P:	Mark Brown
-M:	broonie@opensource.wolfsonmicro.com
-P:	Liam Girdwood
-M:	lrg@slimlogic.co.uk
+M:	Mark Brown <broonie@opensource.wolfsonmicro.com>
+M:	Liam Girdwood <lrg@slimlogic.co.uk>
 L:	linux-input@vger.kernel.org
 T:	git git://opensource.wolfsonmicro.com/linux-2.6-touch
 W:	http://opensource.wolfsonmicro.com/node/7
@@ -6472,8 +5581,7 @@ F:	drivers/input/touchscreen/*wm97*
 F:	include/linux/wm97xx.h
 
 X.25 NETWORK LAYER
-P:	Henner Eisen
-M:	eis@baty.hanse.de
+M:	Henner Eisen <eis@baty.hanse.de>
 L:	linux-x25@vger.kernel.org
 S:	Maintained
 F:	Documentation/networking/x25*
@@ -6481,12 +5589,9 @@ F:	include/net/x25*
 F:	net/x25/
 
 X86 ARCHITECTURE (32-BIT AND 64-BIT)
-P:	Thomas Gleixner
-M:	tglx@linutronix.de
-P:	Ingo Molnar
-M:	mingo@redhat.com
-P:	H. Peter Anvin
-M:	hpa@zytor.com
+M:	Thomas Gleixner <tglx@linutronix.de>
+M:	Ingo Molnar <mingo@redhat.com>
+M:	"H. Peter Anvin" <hpa@zytor.com>
 M:	x86@kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86.git
 S:	Maintained
@@ -6494,10 +5599,8 @@ F:	Documentation/x86/
 F:	arch/x86/
 
 XEN HYPERVISOR INTERFACE
-P:	Jeremy Fitzhardinge
-M:	jeremy@xensource.com
-P:	Chris Wright
-M:	chrisw@sous-sol.org
+M:	Jeremy Fitzhardinge <jeremy@xensource.com>
+M:	Chris Wright <chrisw@sous-sol.org>
 L:	virtualization@lists.osdl.org
 L:	xen-devel@lists.xensource.com
 S:	Supported
@@ -6509,8 +5612,7 @@ F:	include/xen/
 
 XFS FILESYSTEM
 P:	Silicon Graphics Inc
-P:	Felix Blyakher
-M:	felixb@sgi.com
+M:	Felix Blyakher <felixb@sgi.com>
 M:	xfs-masters@oss.sgi.com
 L:	xfs@oss.sgi.com
 W:	http://oss.sgi.com/projects/xfs
@@ -6520,38 +5622,33 @@ F:	Documentation/filesystems/xfs.txt
 F:	fs/xfs/
 
 XILINX SYSTEMACE DRIVER
-P:	Grant Likely
-M:	grant.likely@secretlab.ca
+M:	Grant Likely <grant.likely@secretlab.ca>
 W:	http://www.secretlab.ca/
 S:	Maintained
 F:	drivers/block/xsysace.c
 
 XILINX UARTLITE SERIAL DRIVER
-P:	Peter Korsgaard
-M:	jacmet@sunsite.dk
+M:	Peter Korsgaard <jacmet@sunsite.dk>
 L:	linux-serial@vger.kernel.org
 S:	Maintained
 F:	drivers/serial/uartlite.c
 
 YAM DRIVER FOR AX.25
-P:	Jean-Paul Roubelat
-M:	jpr@f6fbb.org
+M:	Jean-Paul Roubelat <jpr@f6fbb.org>
 L:	linux-hams@vger.kernel.org
 S:	Maintained
 F:	drivers/net/hamradio/yam*
 F:	include/linux/yam.h
 
 YEALINK PHONE DRIVER
-P:	Henk Vergonet
-M:	Henk.Vergonet@gmail.com
+M:	Henk Vergonet <Henk.Vergonet@gmail.com>
 L:	usbb2k-api-dev@nongnu.org
 S:	Maintained
 F:	Documentation/input/yealink.txt
 F:	drivers/input/misc/yealink.*
 
 Z8530 DRIVER FOR AX.25
-P:	Joerg Reuter
-M:	jreuter@yaina.de
+M:	Joerg Reuter <jreuter@yaina.de>
 W:	http://yaina.de/jreuter/
 W:	http://www.qsl.net/dl1bke/
 L:	linux-hams@vger.kernel.org
@@ -6561,10 +5658,8 @@ F:	drivers/net/hamradio/*scc.c
 F:	drivers/net/hamradio/z8530.h
 
 ZD1211RW WIRELESS DRIVER
-P:	Daniel Drake
-M:	dsd@gentoo.org
-P:	Ulrich Kunitz
-M:	kune@deine-taler.de
+M:	Daniel Drake <dsd@gentoo.org>
+M:	Ulrich Kunitz <kune@deine-taler.de>
 W:	http://zd1211.ath.cx/wiki/DriverRewrite
 L:	linux-wireless@vger.kernel.org
 L:	zd1211-devs@lists.sourceforge.net (subscribers-only)
@@ -6580,14 +5675,12 @@ S:	Odd Fixes
 F:	drivers/media/video/zoran/
 
 ZS DECSTATION Z85C30 SERIAL DRIVER
-P:	Maciej W. Rozycki
-M:	macro@linux-mips.org
+M:	"Maciej W. Rozycki" <macro@linux-mips.org>
 S:	Maintained
 F:	drivers/serial/zs.*
 
 THE REST
-P:	Linus Torvalds
-M:	torvalds@linux-foundation.org
+M:	Linus Torvalds <torvalds@linux-foundation.org>
 L:	linux-kernel@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
 S:	Buried alive in reporters
-- 
GitLab


From 2bed6eeb8cb0b5198d8f93e415ee595704bc3534 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Wed, 29 Jul 2009 15:04:32 -0700
Subject: [PATCH 0292/1153] MAINTAINERS: finish off the email address
 coalescing

Add some touchups to the sample record.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index a013e963fc0..a39f3cf940b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -73,8 +73,8 @@ Note: For the hard of thinking, this list is meant to remain in alphabetical
 order. If you could add yourselves to it in alphabetical order that would be
 so much easier [Ed]
 
-P: Person
-M: Mail patches to
+P: Person (obsolete)
+M: Mail patches to: FullName <address@domain>
 L: Mailing list that is relevant to this area
 W: Web-page with status/info
 T: SCM tree type and location.  Type is one of: git, hg, quilt, stgit.
-- 
GitLab


From 084bad91afd0f40ff4db9ceb56e29234c314d8d1 Mon Sep 17 00:00:00 2001
From: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Date: Wed, 29 Jul 2009 15:04:32 -0700
Subject: [PATCH 0293/1153] MAINTAINERS: update HP Jornada 700-series and Epson
 s1d13xxxfb support

Add the relevant git repositories and affected files to the maintainership
of HP Jornada 700-series and Epson s1d13xxxfb support.

Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index a39f3cf940b..66a3865da88 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -624,6 +624,9 @@ ARM/HP JORNADA 7XX MACHINE SUPPORT
 M:	Kristoffer Ericson <kristoffer.ericson@gmail.com>
 W:	www.jlime.com
 S:	Maintained
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/kristoffer/linux-hpc.git
+F:	arch/arm/mach-sa1100/jornada720.c
+F:	arch/arm/mach-sa1100/include/mach/jornada720.h
 
 ARM/INTEL IOP32X ARM ARCHITECTURE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
@@ -1900,6 +1903,7 @@ F:	drivers/video/epson1355fb.c
 EPSON S1D13XXX FRAMEBUFFER DRIVER
 M:	Kristoffer Ericson <kristoffer.ericson@gmail.com>
 S:	Maintained
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/kristoffer/linux-hpc.git
 F:	drivers/video/s1d13xxxfb.c
 F:	include/video/s1d13xxxfb.h
 
-- 
GitLab


From 5bd9052d79daa4c8beb45436c408b6de672adb82 Mon Sep 17 00:00:00 2001
From: Steve French <sfrench@us.ibm.com>
Date: Thu, 30 Jul 2009 02:26:14 +0000
Subject: [PATCH 0294/1153] [CIFS] Updates fs/cifs/CHANGES

Signed-off-by: Steve French <sfrench@us.ibm.com>
---
 fs/cifs/CHANGES | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/fs/cifs/CHANGES b/fs/cifs/CHANGES
index 92888aa9074..651cefde385 100644
--- a/fs/cifs/CHANGES
+++ b/fs/cifs/CHANGES
@@ -1,3 +1,9 @@
+Version 1.60
+-------------
+Fix memory leak in reconnect.  Fix oops in DFS mount error path.
+Set s_maxbytes to smaller (the max that vfs can handle) so that
+sendfile will now work over cifs mounts again.
+
 Version 1.59
 ------------
 Client uses server inode numbers (which are persistent) rather than
-- 
GitLab


From 5156ddce6c0a152ee7ccab2c976c6a8abc8a49b5 Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Wed, 29 Jul 2009 23:04:25 -0500
Subject: [PATCH 0295/1153] powerpc/mm: Fix SMP issue with MMU context handling
 code

In switch_mmu_context() if we call steal_context_smp() to get a context
to use we shouldn't fall through and than call steal_context_up().  Doing
so can be problematic in that the 'mm' that steal_context_up() ends up
using will not get marked dirty in the stale_map[] for other CPUs that
might have used that mm.  Thus we could end up with stale TLB entries in
the other CPUs that can cause all kinda of havoc.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/mm/mmu_context_nohash.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/powerpc/mm/mmu_context_nohash.c b/arch/powerpc/mm/mmu_context_nohash.c
index 92a197117d5..b1a727def15 100644
--- a/arch/powerpc/mm/mmu_context_nohash.c
+++ b/arch/powerpc/mm/mmu_context_nohash.c
@@ -217,6 +217,7 @@ void switch_mmu_context(struct mm_struct *prev, struct mm_struct *next)
 			id = steal_context_smp(id);
 			if (id == MMU_NO_CONTEXT)
 				goto again;
+			goto stolen;
 		}
 #endif /* CONFIG_SMP */
 		id = steal_context_up(id);
-- 
GitLab


From c4673f9a32d7b02bcd2057763d3d368efe5809c3 Mon Sep 17 00:00:00 2001
From: Anton Vorontsov <avorontsov@ru.mvista.com>
Date: Wed, 24 Jun 2009 20:30:28 +0400
Subject: [PATCH 0296/1153] powerpc/85xx: Fix ethernet link detection on
 MPC8569E-MDS boards

Linux isn't able to detect link changes on ethernet ports that were
used by U-Boot. This is because U-Boot wrongly clears interrupt
polarity bit (INTPOL, 0x400) in the extended status register (EXT_SR,
0x1b) of Marvell PHYs.

There is no easy way for PHY drivers to know IRQ line polarity (we
could extract it from the device tree and pass it to phydevs, but
that'll be quite a lot of work), so for now just reset the PHYs to
their default states.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/platforms/85xx/mpc85xx_mds.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
index 60ed9c067b1..bfb32834ab0 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
@@ -233,6 +233,19 @@ static void __init mpc85xx_mds_setup_arch(void)
 			/* Turn UCC1 & UCC2 on */
 			setbits8(&bcsr_regs[8], BCSR_UCC1_GETH_EN);
 			setbits8(&bcsr_regs[9], BCSR_UCC2_GETH_EN);
+		} else if (machine_is(mpc8569_mds)) {
+#define BCSR7_UCC12_GETHnRST	(0x1 << 2)
+#define BCSR8_UEM_MARVELL_RST	(0x1 << 1)
+			/*
+			 * U-Boot mangles interrupt polarity for Marvell PHYs,
+			 * so reset built-in and UEM Marvell PHYs, this puts
+			 * the PHYs into their normal state.
+			 */
+			clrbits8(&bcsr_regs[7], BCSR7_UCC12_GETHnRST);
+			setbits8(&bcsr_regs[8], BCSR8_UEM_MARVELL_RST);
+
+			setbits8(&bcsr_regs[7], BCSR7_UCC12_GETHnRST);
+			clrbits8(&bcsr_regs[8], BCSR8_UEM_MARVELL_RST);
 		}
 		iounmap(bcsr_regs);
 	}
-- 
GitLab


From 8a0b177f367a8fd03dc5ba1f5a4494d1424471aa Mon Sep 17 00:00:00 2001
From: Anton Vorontsov <cbouatmailru@gmail.com>
Date: Wed, 1 Jul 2009 21:39:25 +0400
Subject: [PATCH 0297/1153] powerpc/85xx: Don't scan for TBI PHY addresses on
 MPC8569E-MDS boards

Sometimes (e.g. when there are no UEMs attached to a board)
fsl_pq_mdio_find_free() fails to find a spare address for a TBI PHY,
this is because get_phy_id() returns bogus 0x0000ffff values
(0xffffffff is expected), and therefore mdio bus probing fails with
the following message:

  fsl-pq_mdio: probe of e0082120.mdio failed with error -16

And obviously ethernet doesn't work after this.

This patch solves the problem by adding tbi-phy node into mdio node,
so that we won't scan for spare addresses, we'll just use a fixed one.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/boot/dts/mpc8569mds.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/powerpc/boot/dts/mpc8569mds.dts b/arch/powerpc/boot/dts/mpc8569mds.dts
index a680165292f..9e4ce99e161 100644
--- a/arch/powerpc/boot/dts/mpc8569mds.dts
+++ b/arch/powerpc/boot/dts/mpc8569mds.dts
@@ -501,6 +501,10 @@
 				reg = <0x6>;
 				device_type = "ethernet-phy";
 			};
+			tbi-phy@11 {
+				reg = <0x11>;
+				device_type = "tbi-phy";
+			};
 		};
 		mdio@3520 {
 			#address-cells = <1>;
-- 
GitLab


From 1333c3d6d35bdb109ddbd4b7086cbf066a27b156 Mon Sep 17 00:00:00 2001
From: Anton Vorontsov <avorontsov@ru.mvista.com>
Date: Tue, 21 Jul 2009 01:36:43 +0400
Subject: [PATCH 0298/1153] powerpc/83xx: Fix PCI IO base address on
 MPC837xE-RDB boards

U-Boot maps PCI IO at 0xe0300000, while current dts files specify
0xe2000000. This leads to the following oops with CONFIG_8139TOO_PIO=y.

8139too Fast Ethernet driver 0.9.28
Machine check in kernel mode.
Caused by (from SRR1=41000): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
MPC837x RDB
[...]
NIP [00000900] 0x900
LR [c0439df8] rtl8139_init_board+0x238/0x524
Call Trace:
[cf831d90] [c0439dcc] rtl8139_init_board+0x20c/0x524 (unreliable)
[cf831de0] [c043a15c] rtl8139_init_one+0x78/0x65c
[cf831e40] [c0235250] pci_call_probe+0x20/0x30
[...]

This patch fixes the issue by specifying the correct PCI IO base
address.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/boot/dts/mpc8377_rdb.dts | 2 +-
 arch/powerpc/boot/dts/mpc8378_rdb.dts | 2 +-
 arch/powerpc/boot/dts/mpc8379_rdb.dts | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/powerpc/boot/dts/mpc8377_rdb.dts b/arch/powerpc/boot/dts/mpc8377_rdb.dts
index 224b4f0704b..4f06dbc0d27 100644
--- a/arch/powerpc/boot/dts/mpc8377_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8377_rdb.dts
@@ -410,7 +410,7 @@
 		bus-range = <0 0>;
 		ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
 		          0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
-		          0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+		          0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>;
 		sleep = <&pmc 0x00010000>;
 		clock-frequency = <66666666>;
 		#interrupt-cells = <1>;
diff --git a/arch/powerpc/boot/dts/mpc8378_rdb.dts b/arch/powerpc/boot/dts/mpc8378_rdb.dts
index 474ea2fa3f8..aabf3437cad 100644
--- a/arch/powerpc/boot/dts/mpc8378_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8378_rdb.dts
@@ -394,7 +394,7 @@
 		bus-range = <0 0>;
 		ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
 		          0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
-		          0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+		          0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>;
 		sleep = <&pmc 0x00010000>;
 		clock-frequency = <66666666>;
 		#interrupt-cells = <1>;
diff --git a/arch/powerpc/boot/dts/mpc8379_rdb.dts b/arch/powerpc/boot/dts/mpc8379_rdb.dts
index d4838af8d37..9b1da864d89 100644
--- a/arch/powerpc/boot/dts/mpc8379_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8379_rdb.dts
@@ -424,7 +424,7 @@
 		bus-range = <0x0 0x0>;
 		ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
 		          0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
-		          0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+		          0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>;
 		sleep = <&pmc 0x00010000>;
 		clock-frequency = <66666666>;
 		#interrupt-cells = <1>;
-- 
GitLab


From 6e900de3fff01e84c96632409359a84825c54b28 Mon Sep 17 00:00:00 2001
From: Mark Ware <mware@elphinstone.net>
Date: Mon, 20 Jul 2009 21:51:03 +1000
Subject: [PATCH 0299/1153] cpm_uart: Don't use alloc_bootmem in
 cpm_uart_cpm2.c

This is another alloc_bootmem() -> kzalloc() change, this time to
fix the non-fatal badness caused when booting with a cpm2_uart console.

Signed-off-by: Mark Ware <mware@elphinstone.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 drivers/serial/cpm_uart/cpm_uart_cpm2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm2.c b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
index 141c0a3333a..a9802e76b5f 100644
--- a/drivers/serial/cpm_uart/cpm_uart_cpm2.c
+++ b/drivers/serial/cpm_uart/cpm_uart_cpm2.c
@@ -132,7 +132,7 @@ int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con)
 	memsz = L1_CACHE_ALIGN(pinfo->rx_nrfifos * pinfo->rx_fifosize) +
 	    L1_CACHE_ALIGN(pinfo->tx_nrfifos * pinfo->tx_fifosize);
 	if (is_con) {
-		mem_addr = alloc_bootmem(memsz);
+		mem_addr = kzalloc(memsz, GFP_NOWAIT);
 		dma_addr = virt_to_bus(mem_addr);
 	}
 	else
-- 
GitLab


From f27d4d47dcf8906c8a22908dc1d32ec641e9fbe0 Mon Sep 17 00:00:00 2001
From: Martyn Welch <martyn.welch@gefanuc.com>
Date: Thu, 2 Jul 2009 15:18:35 +0100
Subject: [PATCH 0300/1153] powerpc/86xx: Update defconfig for GE Fanuc's PPC9A

General update of defconfig including the following notable changes:
 - Enable GPIO access via sysfs on GE Fanuc's PPC9A.
 - Enable Highmem support.
 - Support for PCMCIA based daughter card.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/configs/86xx/gef_ppc9a_defconfig | 518 +++++++-----------
 1 file changed, 196 insertions(+), 322 deletions(-)

diff --git a/arch/powerpc/configs/86xx/gef_ppc9a_defconfig b/arch/powerpc/configs/86xx/gef_ppc9a_defconfig
index b6a23af57f4..d8354d993b2 100644
--- a/arch/powerpc/configs/86xx/gef_ppc9a_defconfig
+++ b/arch/powerpc/configs/86xx/gef_ppc9a_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:31 2009
+# Linux kernel version: 2.6.30
+# Thu Jul  2 13:55:24 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_PHYS_64BIT is not set
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_PPC32=y
@@ -32,6 +34,7 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
@@ -41,7 +44,6 @@ CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_GENERIC_LOCKBREAK=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -56,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 CONFIG_GENERIC_TBSYNC=y
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -112,9 +116,7 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -127,8 +129,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -143,6 +152,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_USE_GENERIC_SMP_HELPERS=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -156,7 +169,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -216,7 +229,7 @@ CONFIG_MPIC=y
 #
 # Kernel options
 #
-# CONFIG_HIGHMEM is not set
+CONFIG_HIGHMEM=y
 CONFIG_TICK_ONESHOT=y
 # CONFIG_NO_HZ is not set
 CONFIG_HIGH_RES_TIMERS=y
@@ -235,6 +248,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=m
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -256,9 +270,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -285,14 +299,32 @@ CONFIG_PCI_DOMAINS=y
 CONFIG_PCI_SYSCALL=y
 CONFIG_PCIEPORTBUS=y
 CONFIG_PCIEAER=y
+# CONFIG_PCIE_ECRC is not set
+# CONFIG_PCIEAER_INJECT is not set
 # CONFIG_PCIEASPM is not set
 CONFIG_ARCH_SUPPORTS_MSI=y
 # CONFIG_PCI_MSI is not set
 # CONFIG_PCI_LEGACY is not set
-CONFIG_PCI_DEBUG=y
 # CONFIG_PCI_STUB is not set
 # CONFIG_PCI_IOV is not set
-# CONFIG_PCCARD is not set
+CONFIG_PCCARD=y
+# CONFIG_PCMCIA_DEBUG is not set
+CONFIG_PCMCIA=y
+# CONFIG_PCMCIA_LOAD_CIS is not set
+# CONFIG_PCMCIA_IOCTL is not set
+# CONFIG_CARDBUS is not set
+
+#
+# PC-card bridges
+#
+CONFIG_YENTA=y
+# CONFIG_YENTA_O2 is not set
+# CONFIG_YENTA_RICOH is not set
+CONFIG_YENTA_TI=y
+# CONFIG_YENTA_TOSHIBA is not set
+# CONFIG_PD6729 is not set
+# CONFIG_I82092 is not set
+CONFIG_PCCARD_NONSTATIC=y
 # CONFIG_HOTPLUG_PCI is not set
 # CONFIG_HAS_RAPIDIO is not set
 
@@ -353,8 +385,8 @@ CONFIG_INET_XFRM_TUNNEL=m
 CONFIG_INET_TUNNEL=m
 CONFIG_INET_XFRM_MODE_TRANSPORT=y
 CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
-# CONFIG_INET_LRO is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_LRO=y
 CONFIG_INET_DIAG=y
 CONFIG_INET_TCP_DIAG=y
 # CONFIG_TCP_CONG_ADVANCED is not set
@@ -380,174 +412,26 @@ CONFIG_IPV6_NDISC_NODETYPE=y
 CONFIG_IPV6_TUNNEL=m
 # CONFIG_IPV6_MULTIPLE_TABLES is not set
 # CONFIG_IPV6_MROUTE is not set
-# CONFIG_NETLABEL is not set
 # CONFIG_NETWORK_SECMARK is not set
-CONFIG_NETFILTER=y
-# CONFIG_NETFILTER_DEBUG is not set
-CONFIG_NETFILTER_ADVANCED=y
-CONFIG_BRIDGE_NETFILTER=y
-
-#
-# Core Netfilter Configuration
-#
-# CONFIG_NETFILTER_NETLINK_QUEUE is not set
-# CONFIG_NETFILTER_NETLINK_LOG is not set
-# CONFIG_NF_CONNTRACK is not set
-# CONFIG_NETFILTER_TPROXY is not set
-CONFIG_NETFILTER_XTABLES=m
-# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set
-# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
-# CONFIG_NETFILTER_XT_TARGET_HL is not set
-# CONFIG_NETFILTER_XT_TARGET_MARK is not set
-# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set
-# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set
-# CONFIG_NETFILTER_XT_TARGET_RATEEST is not set
-# CONFIG_NETFILTER_XT_TARGET_TRACE is not set
-# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set
-# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set
-# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set
-# CONFIG_NETFILTER_XT_MATCH_DCCP is not set
-# CONFIG_NETFILTER_XT_MATCH_DSCP is not set
-# CONFIG_NETFILTER_XT_MATCH_ESP is not set
-# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set
-CONFIG_NETFILTER_XT_MATCH_HL=m
-# CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set
-# CONFIG_NETFILTER_XT_MATCH_LENGTH is not set
-# CONFIG_NETFILTER_XT_MATCH_LIMIT is not set
-# CONFIG_NETFILTER_XT_MATCH_MAC is not set
-# CONFIG_NETFILTER_XT_MATCH_MARK is not set
-# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set
-# CONFIG_NETFILTER_XT_MATCH_OWNER is not set
-# CONFIG_NETFILTER_XT_MATCH_POLICY is not set
-# CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set
-# CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set
-# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set
-# CONFIG_NETFILTER_XT_MATCH_RATEEST is not set
-# CONFIG_NETFILTER_XT_MATCH_REALM is not set
-# CONFIG_NETFILTER_XT_MATCH_RECENT is not set
-# CONFIG_NETFILTER_XT_MATCH_SCTP is not set
-# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set
-# CONFIG_NETFILTER_XT_MATCH_STRING is not set
-# CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set
-# CONFIG_NETFILTER_XT_MATCH_TIME is not set
-# CONFIG_NETFILTER_XT_MATCH_U32 is not set
-# CONFIG_IP_VS is not set
-
-#
-# IP: Netfilter Configuration
-#
-# CONFIG_NF_DEFRAG_IPV4 is not set
-CONFIG_IP_NF_QUEUE=m
-CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
-# CONFIG_IP_NF_MATCH_AH is not set
-CONFIG_IP_NF_MATCH_ECN=m
-CONFIG_IP_NF_MATCH_TTL=m
-CONFIG_IP_NF_FILTER=m
-CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
-CONFIG_IP_NF_TARGET_ULOG=m
-CONFIG_IP_NF_MANGLE=m
-CONFIG_IP_NF_TARGET_ECN=m
-# CONFIG_IP_NF_TARGET_TTL is not set
-CONFIG_IP_NF_RAW=m
-# CONFIG_IP_NF_SECURITY is not set
-CONFIG_IP_NF_ARPTABLES=m
-CONFIG_IP_NF_ARPFILTER=m
-CONFIG_IP_NF_ARP_MANGLE=m
-
-#
-# IPv6: Netfilter Configuration
-#
-CONFIG_IP6_NF_QUEUE=m
-CONFIG_IP6_NF_IPTABLES=m
-# CONFIG_IP6_NF_MATCH_AH is not set
-CONFIG_IP6_NF_MATCH_EUI64=m
-CONFIG_IP6_NF_MATCH_FRAG=m
-CONFIG_IP6_NF_MATCH_OPTS=m
-CONFIG_IP6_NF_MATCH_HL=m
-CONFIG_IP6_NF_MATCH_IPV6HEADER=m
-# CONFIG_IP6_NF_MATCH_MH is not set
-CONFIG_IP6_NF_MATCH_RT=m
-# CONFIG_IP6_NF_TARGET_HL is not set
-CONFIG_IP6_NF_TARGET_LOG=m
-CONFIG_IP6_NF_FILTER=m
-# CONFIG_IP6_NF_TARGET_REJECT is not set
-CONFIG_IP6_NF_MANGLE=m
-CONFIG_IP6_NF_RAW=m
-# CONFIG_IP6_NF_SECURITY is not set
-# CONFIG_BRIDGE_NF_EBTABLES is not set
+# CONFIG_NETFILTER is not set
 # CONFIG_IP_DCCP is not set
-CONFIG_IP_SCTP=m
-# CONFIG_SCTP_DBG_MSG is not set
-# CONFIG_SCTP_DBG_OBJCNT is not set
-# CONFIG_SCTP_HMAC_NONE is not set
-# CONFIG_SCTP_HMAC_SHA1 is not set
-CONFIG_SCTP_HMAC_MD5=y
-CONFIG_TIPC=m
-# CONFIG_TIPC_ADVANCED is not set
-# CONFIG_TIPC_DEBUG is not set
-CONFIG_ATM=m
-CONFIG_ATM_CLIP=m
-# CONFIG_ATM_CLIP_NO_ICMP is not set
-CONFIG_ATM_LANE=m
-CONFIG_ATM_MPOA=m
-CONFIG_ATM_BR2684=m
-# CONFIG_ATM_BR2684_IPFILTER is not set
-CONFIG_STP=m
-CONFIG_BRIDGE=m
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
 # CONFIG_NET_DSA is not set
-CONFIG_VLAN_8021Q=m
-# CONFIG_VLAN_8021Q_GVRP is not set
+# CONFIG_VLAN_8021Q is not set
 # CONFIG_DECNET is not set
-CONFIG_LLC=m
 # CONFIG_LLC2 is not set
 # CONFIG_IPX is not set
 # CONFIG_ATALK is not set
 # CONFIG_X25 is not set
 # CONFIG_LAPB is not set
 # CONFIG_ECONET is not set
-CONFIG_WAN_ROUTER=m
+# CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
-CONFIG_NET_SCHED=y
-
-#
-# Queueing/Scheduling
-#
-CONFIG_NET_SCH_CBQ=m
-CONFIG_NET_SCH_HTB=m
-CONFIG_NET_SCH_HFSC=m
-CONFIG_NET_SCH_ATM=m
-CONFIG_NET_SCH_PRIO=m
-# CONFIG_NET_SCH_MULTIQ is not set
-CONFIG_NET_SCH_RED=m
-CONFIG_NET_SCH_SFQ=m
-CONFIG_NET_SCH_TEQL=m
-CONFIG_NET_SCH_TBF=m
-CONFIG_NET_SCH_GRED=m
-CONFIG_NET_SCH_DSMARK=m
-CONFIG_NET_SCH_NETEM=m
-# CONFIG_NET_SCH_DRR is not set
-
-#
-# Classification
-#
-CONFIG_NET_CLS=y
-# CONFIG_NET_CLS_BASIC is not set
-CONFIG_NET_CLS_TCINDEX=m
-CONFIG_NET_CLS_ROUTE4=m
-CONFIG_NET_CLS_ROUTE=y
-CONFIG_NET_CLS_FW=m
-CONFIG_NET_CLS_U32=m
-# CONFIG_CLS_U32_PERF is not set
-# CONFIG_CLS_U32_MARK is not set
-CONFIG_NET_CLS_RSVP=m
-CONFIG_NET_CLS_RSVP6=m
-# CONFIG_NET_CLS_FLOW is not set
-# CONFIG_NET_EMATCH is not set
-# CONFIG_NET_CLS_ACT is not set
-# CONFIG_NET_CLS_IND is not set
-CONFIG_NET_SCH_FIFO=y
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
 #
@@ -560,12 +444,7 @@ CONFIG_NET_PKTGEN=m
 # CONFIG_BT is not set
 # CONFIG_AF_RXRPC is not set
 CONFIG_FIB_RULES=y
-CONFIG_WIRELESS=y
-# CONFIG_CFG80211 is not set
-CONFIG_WIRELESS_OLD_REGULATORY=y
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+# CONFIG_WIRELESS is not set
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -580,9 +459,9 @@ CONFIG_WIRELESS_OLD_REGULATORY=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_STANDALONE=y
 CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
-# CONFIG_DEBUG_DRIVER is not set
-# CONFIG_DEBUG_DEVRES is not set
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
 # CONFIG_SYS_HYPERVISOR is not set
 # CONFIG_CONNECTOR is not set
 CONFIG_MTD=y
@@ -672,6 +551,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -707,9 +587,60 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
-# CONFIG_IDE is not set
+CONFIG_IDE=y
+
+#
+# Please see Documentation/ide/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+CONFIG_IDE_GD=y
+CONFIG_IDE_GD_ATA=y
+# CONFIG_IDE_GD_ATAPI is not set
+CONFIG_BLK_DEV_IDECS=y
+# CONFIG_BLK_DEV_IDECD is not set
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
+
+#
+# IDE chipset support/bugfixes
+#
+# CONFIG_BLK_DEV_PLATFORM is not set
+
+#
+# PCI IDE chipsets support
+#
+# CONFIG_BLK_DEV_GENERIC is not set
+# CONFIG_BLK_DEV_OPTI621 is not set
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_JMICRON is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8172 is not set
+# CONFIG_BLK_DEV_IT8213 is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
+# CONFIG_BLK_DEV_IDEDMA is not set
 
 #
 # SCSI device support
@@ -731,10 +662,6 @@ CONFIG_BLK_DEV_SR=y
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 # CONFIG_CHR_DEV_SG is not set
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -751,6 +678,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 # CONFIG_SCSI_SRP_ATTRS is not set
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -759,6 +687,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -778,7 +707,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -791,6 +719,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_NSP32 is not set
 # CONFIG_SCSI_DEBUG is not set
 # CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
 # CONFIG_SCSI_DH is not set
 # CONFIG_SCSI_OSD_INITIATOR is not set
 CONFIG_ATA=y
@@ -842,6 +771,7 @@ CONFIG_SATA_SIL=y
 # CONFIG_PATA_NS87415 is not set
 # CONFIG_PATA_OPTI is not set
 # CONFIG_PATA_OPTIDMA is not set
+# CONFIG_PATA_PCMCIA is not set
 # CONFIG_PATA_PDC_OLD is not set
 # CONFIG_PATA_RADISYS is not set
 # CONFIG_PATA_RZ1000 is not set
@@ -862,14 +792,17 @@ CONFIG_SATA_SIL=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=m
 CONFIG_BONDING=m
 # CONFIG_MACVLAN is not set
@@ -916,6 +849,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -935,8 +869,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -963,22 +899,8 @@ CONFIG_GIANFAR=y
 # CONFIG_USB_PEGASUS is not set
 # CONFIG_USB_RTL8150 is not set
 # CONFIG_USB_USBNET is not set
+# CONFIG_NET_PCMCIA is not set
 # CONFIG_WAN is not set
-CONFIG_ATM_DRIVERS=y
-# CONFIG_ATM_DUMMY is not set
-# CONFIG_ATM_TCP is not set
-# CONFIG_ATM_LANAI is not set
-# CONFIG_ATM_ENI is not set
-# CONFIG_ATM_FIRESTREAM is not set
-# CONFIG_ATM_ZATM is not set
-# CONFIG_ATM_NICSTAR is not set
-# CONFIG_ATM_IDT77252 is not set
-# CONFIG_ATM_AMBASSADOR is not set
-# CONFIG_ATM_HORIZON is not set
-# CONFIG_ATM_IA is not set
-# CONFIG_ATM_FORE200E is not set
-# CONFIG_ATM_HE is not set
-# CONFIG_ATM_SOLOS is not set
 # CONFIG_FDDI is not set
 # CONFIG_HIPPI is not set
 CONFIG_PPP=m
@@ -990,7 +912,6 @@ CONFIG_PPP_DEFLATE=m
 CONFIG_PPP_BSDCOMP=m
 # CONFIG_PPP_MPPE is not set
 CONFIG_PPPOE=m
-CONFIG_PPPOATM=m
 # CONFIG_PPPOL2TP is not set
 CONFIG_SLIP=m
 CONFIG_SLIP_COMPRESSED=y
@@ -1010,7 +931,7 @@ CONFIG_NET_POLL_CONTROLLER=y
 # Input device support
 #
 CONFIG_INPUT=y
-CONFIG_INPUT_FF_MEMLESS=m
+# CONFIG_INPUT_FF_MEMLESS is not set
 # CONFIG_INPUT_POLLDEV is not set
 
 #
@@ -1058,6 +979,7 @@ CONFIG_DEVKMEM=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 # CONFIG_SERIAL_8250_PCI is not set
+# CONFIG_SERIAL_8250_CS is not set
 CONFIG_SERIAL_8250_NR_UARTS=2
 CONFIG_SERIAL_8250_RUNTIME_UARTS=2
 # CONFIG_SERIAL_8250_EXTENDED is not set
@@ -1080,6 +1002,14 @@ CONFIG_HW_RANDOM=y
 CONFIG_NVRAM=y
 # CONFIG_R3964 is not set
 # CONFIG_APPLICOM is not set
+
+#
+# PCMCIA character devices
+#
+# CONFIG_SYNCLINK_CS is not set
+# CONFIG_CARDMAN_4000 is not set
+# CONFIG_CARDMAN_4040 is not set
+# CONFIG_IPWIRELESS is not set
 # CONFIG_RAW_DRIVER is not set
 # CONFIG_TCG_TPM is not set
 CONFIG_DEVPORT=y
@@ -1143,18 +1073,21 @@ CONFIG_DS1682=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
-# CONFIG_DEBUG_GPIO is not set
-# CONFIG_GPIO_SYSFS is not set
+CONFIG_GPIO_SYSFS=y
 
 #
 # Memory mapped GPIO expanders:
@@ -1229,6 +1162,7 @@ CONFIG_SENSORS_LM92=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1284,24 +1218,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1346,7 +1265,7 @@ CONFIG_HID_BELKIN=y
 CONFIG_HID_CHERRY=y
 CONFIG_HID_CHICONY=y
 CONFIG_HID_CYPRESS=y
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 CONFIG_HID_EZKEY=y
 # CONFIG_HID_KYE is not set
 CONFIG_HID_GYRATION=y
@@ -1363,10 +1282,11 @@ CONFIG_HID_PETALYNX=y
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-CONFIG_THRUSTMASTER_FF=m
-CONFIG_ZEROPLUS_FF=m
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1392,6 +1312,7 @@ CONFIG_USB=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1475,7 +1396,6 @@ CONFIG_USB_STORAGE=y
 # CONFIG_USB_IOWARRIOR is not set
 # CONFIG_USB_ISIGHTFW is not set
 # CONFIG_USB_VST is not set
-# CONFIG_USB_ATM is not set
 # CONFIG_USB_GADGET is not set
 
 #
@@ -1521,6 +1441,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 CONFIG_RTC_DRV_RX8581=y
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1548,6 +1469,10 @@ CONFIG_RTC_DRV_RX8581=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1569,10 +1494,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1589,8 +1516,11 @@ CONFIG_INOTIFY_USER=y
 #
 # CD-ROM/DVD Filesystems
 #
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
+CONFIG_ISO9660_FS=y
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=y
+CONFIG_UDF_NLS=y
 
 #
 # DOS/FAT/NT Filesystems
@@ -1598,8 +1528,8 @@ CONFIG_INOTIFY_USER=y
 CONFIG_FAT_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_VFAT_FS=y
-CONFIG_FAT_DEFAULT_CODEPAGE=437
-CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+CONFIG_FAT_DEFAULT_CODEPAGE=850
+CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
 # CONFIG_NTFS_FS is not set
 
 #
@@ -1649,6 +1579,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1723,13 +1654,13 @@ CONFIG_NLS_UTF8=m
 #
 CONFIG_BITREVERSE=y
 CONFIG_GENERIC_FIND_LAST_BIT=y
-CONFIG_CRC_CCITT=m
+CONFIG_CRC_CCITT=y
 # CONFIG_CRC16 is not set
-# CONFIG_CRC_T10DIF is not set
-# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC_T10DIF=y
+CONFIG_CRC_ITU_T=y
 CONFIG_CRC32=y
 # CONFIG_CRC7 is not set
-CONFIG_LIBCRC32C=m
+CONFIG_LIBCRC32C=y
 CONFIG_ZLIB_INFLATE=y
 CONFIG_ZLIB_DEFLATE=y
 CONFIG_DECOMPRESS_GZIP=y
@@ -1738,6 +1669,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1750,75 +1682,24 @@ CONFIG_MAGIC_SYSRQ=y
 # CONFIG_UNUSED_SYMBOLS is not set
 # CONFIG_DEBUG_FS is not set
 # CONFIG_HEADERS_CHECK is not set
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_DETECT_SOFTLOCKUP=y
-# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
-CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
-CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
-CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
-CONFIG_SCHED_DEBUG=y
-# CONFIG_SCHEDSTATS is not set
-# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_OBJECTS is not set
-# CONFIG_DEBUG_SLAB is not set
-# CONFIG_DEBUG_RT_MUTEXES is not set
-# CONFIG_RT_MUTEX_TESTER is not set
-# CONFIG_DEBUG_SPINLOCK is not set
-# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
-# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_KERNEL is not set
 # CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
-# CONFIG_DEBUG_VM is not set
-# CONFIG_DEBUG_WRITECOUNT is not set
 # CONFIG_DEBUG_MEMORY_INIT is not set
-# CONFIG_DEBUG_LIST is not set
-# CONFIG_DEBUG_SG is not set
-# CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
-# CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
-# CONFIG_BACKTRACE_SELF_TEST is not set
-# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
-# CONFIG_FAULT_INJECTION is not set
 # CONFIG_LATENCYTOP is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
-# CONFIG_DEBUG_PAGEALLOC is not set
 CONFIG_HAVE_FUNCTION_TRACER=y
 CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_PREEMPT_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
-# CONFIG_KGDB is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
-# CONFIG_DEBUG_STACKOVERFLOW is not set
-# CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_CODE_PATCHING_SELFTEST is not set
-# CONFIG_FTR_FIXUP_SELFTEST is not set
-# CONFIG_MSI_BITMAP_SELFTEST is not set
-# CONFIG_XMON is not set
 # CONFIG_IRQSTACKS is not set
-# CONFIG_BDI_SWITCH is not set
 # CONFIG_BOOTX_TEXT is not set
 # CONFIG_PPC_EARLY_DEBUG is not set
 
@@ -1826,15 +1707,9 @@ CONFIG_PRINT_STACK_DEPTH=64
 # Security options
 #
 # CONFIG_KEYS is not set
-CONFIG_SECURITY=y
+# CONFIG_SECURITY is not set
 # CONFIG_SECURITYFS is not set
-CONFIG_SECURITY_NETWORK=y
-# CONFIG_SECURITY_NETWORK_XFRM is not set
-# CONFIG_SECURITY_PATH is not set
 # CONFIG_SECURITY_FILE_CAPABILITIES is not set
-# CONFIG_SECURITY_ROOTPLUG is not set
-CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0
-# CONFIG_SECURITY_TOMOYO is not set
 CONFIG_CRYPTO=y
 
 #
@@ -1854,11 +1729,11 @@ CONFIG_CRYPTO_PCOMP=y
 CONFIG_CRYPTO_MANAGER=y
 CONFIG_CRYPTO_MANAGER2=y
 # CONFIG_CRYPTO_GF128MUL is not set
-CONFIG_CRYPTO_NULL=m
+# CONFIG_CRYPTO_NULL is not set
 CONFIG_CRYPTO_WORKQUEUE=y
 # CONFIG_CRYPTO_CRYPTD is not set
 CONFIG_CRYPTO_AUTHENC=m
-CONFIG_CRYPTO_TEST=m
+# CONFIG_CRYPTO_TEST is not set
 
 #
 # Authenticated Encryption with Associated Data
@@ -1873,53 +1748,52 @@ CONFIG_CRYPTO_TEST=m
 CONFIG_CRYPTO_CBC=y
 # CONFIG_CRYPTO_CTR is not set
 # CONFIG_CRYPTO_CTS is not set
-CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_ECB is not set
 # CONFIG_CRYPTO_LRW is not set
-CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_PCBC is not set
 # CONFIG_CRYPTO_XTS is not set
 
 #
 # Hash modes
 #
-CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_HMAC=m
 # CONFIG_CRYPTO_XCBC is not set
 
 #
 # Digest
 #
-CONFIG_CRYPTO_CRC32C=m
-CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_MD4 is not set
 CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_MICHAEL_MIC=m
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
 # CONFIG_CRYPTO_RMD128 is not set
 # CONFIG_CRYPTO_RMD160 is not set
 # CONFIG_CRYPTO_RMD256 is not set
 # CONFIG_CRYPTO_RMD320 is not set
 CONFIG_CRYPTO_SHA1=m
-CONFIG_CRYPTO_SHA256=m
-CONFIG_CRYPTO_SHA512=m
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
 # CONFIG_CRYPTO_TGR192 is not set
-CONFIG_CRYPTO_WP512=m
+# CONFIG_CRYPTO_WP512 is not set
 
 #
 # Ciphers
 #
-CONFIG_CRYPTO_AES=m
-CONFIG_CRYPTO_ANUBIS=m
-CONFIG_CRYPTO_ARC4=m
-CONFIG_CRYPTO_BLOWFISH=m
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
 # CONFIG_CRYPTO_CAMELLIA is not set
-CONFIG_CRYPTO_CAST5=m
-CONFIG_CRYPTO_CAST6=m
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
 CONFIG_CRYPTO_DES=y
 # CONFIG_CRYPTO_FCRYPT is not set
-CONFIG_CRYPTO_KHAZAD=m
+# CONFIG_CRYPTO_KHAZAD is not set
 # CONFIG_CRYPTO_SALSA20 is not set
 # CONFIG_CRYPTO_SEED is not set
-CONFIG_CRYPTO_SERPENT=m
-CONFIG_CRYPTO_TEA=m
-CONFIG_CRYPTO_TWOFISH=m
-CONFIG_CRYPTO_TWOFISH_COMMON=m
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
 
 #
 # Compression
-- 
GitLab


From 083e268c8b78606658f2e4524168ff45825d879e Mon Sep 17 00:00:00 2001
From: Martyn Welch <martyn.welch@gefanuc.com>
Date: Thu, 2 Jul 2009 15:18:44 +0100
Subject: [PATCH 0301/1153] powerpc/86xx: Update GE Fanuc sbc310 default
 configuration

General update of defconfig including the following notable changes:
 - Enable Highmem support.
 - Support for PCMCIA based daughter card.

Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 .../powerpc/configs/86xx/gef_sbc310_defconfig | 213 +++++++++++++-----
 1 file changed, 154 insertions(+), 59 deletions(-)

diff --git a/arch/powerpc/configs/86xx/gef_sbc310_defconfig b/arch/powerpc/configs/86xx/gef_sbc310_defconfig
index a66910e6334..f2362e5bf06 100644
--- a/arch/powerpc/configs/86xx/gef_sbc310_defconfig
+++ b/arch/powerpc/configs/86xx/gef_sbc310_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:29 2009
+# Linux kernel version: 2.6.30
+# Thu Jul  2 14:10:12 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_PHYS_64BIT is not set
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_PPC32=y
@@ -32,6 +34,7 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
@@ -41,7 +44,6 @@ CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_GENERIC_LOCKBREAK=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -56,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 CONFIG_GENERIC_TBSYNC=y
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -91,7 +95,11 @@ CONFIG_CLASSIC_RCU=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_GROUP_SCHED is not set
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
 # CONFIG_CGROUPS is not set
 CONFIG_SYSFS_DEPRECATED=y
 CONFIG_SYSFS_DEPRECATED_V2=y
@@ -109,7 +117,6 @@ CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -122,8 +129,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -138,6 +152,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_USE_GENERIC_SMP_HELPERS=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -151,7 +169,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -168,7 +186,6 @@ CONFIG_DEFAULT_CFQ=y
 # CONFIG_DEFAULT_NOOP is not set
 CONFIG_DEFAULT_IOSCHED="cfq"
 # CONFIG_FREEZER is not set
-CONFIG_PPC_MSI_BITMAP=y
 
 #
 # Platform support
@@ -212,7 +229,7 @@ CONFIG_MPIC=y
 #
 # Kernel options
 #
-# CONFIG_HIGHMEM is not set
+CONFIG_HIGHMEM=y
 CONFIG_TICK_ONESHOT=y
 # CONFIG_NO_HZ is not set
 CONFIG_HIGH_RES_TIMERS=y
@@ -231,6 +248,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -252,9 +270,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -281,13 +299,32 @@ CONFIG_PCI_DOMAINS=y
 CONFIG_PCI_SYSCALL=y
 CONFIG_PCIEPORTBUS=y
 CONFIG_PCIEAER=y
+# CONFIG_PCIE_ECRC is not set
+# CONFIG_PCIEAER_INJECT is not set
 # CONFIG_PCIEASPM is not set
 CONFIG_ARCH_SUPPORTS_MSI=y
-CONFIG_PCI_MSI=y
+# CONFIG_PCI_MSI is not set
 # CONFIG_PCI_LEGACY is not set
 # CONFIG_PCI_STUB is not set
 # CONFIG_PCI_IOV is not set
-# CONFIG_PCCARD is not set
+CONFIG_PCCARD=y
+# CONFIG_PCMCIA_DEBUG is not set
+CONFIG_PCMCIA=y
+# CONFIG_PCMCIA_LOAD_CIS is not set
+# CONFIG_PCMCIA_IOCTL is not set
+# CONFIG_CARDBUS is not set
+
+#
+# PC-card bridges
+#
+CONFIG_YENTA=y
+# CONFIG_YENTA_O2 is not set
+# CONFIG_YENTA_RICOH is not set
+CONFIG_YENTA_TI=y
+# CONFIG_YENTA_TOSHIBA is not set
+# CONFIG_PD6729 is not set
+# CONFIG_I82092 is not set
+CONFIG_PCCARD_NONSTATIC=y
 # CONFIG_HOTPLUG_PCI is not set
 # CONFIG_HAS_RAPIDIO is not set
 
@@ -393,6 +430,7 @@ CONFIG_IPV6_TUNNEL=m
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -421,7 +459,9 @@ CONFIG_FIB_RULES=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_STANDALONE=y
 CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
 # CONFIG_SYS_HYPERVISOR is not set
 # CONFIG_CONNECTOR is not set
 CONFIG_MTD=y
@@ -511,6 +551,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -546,9 +587,60 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
-# CONFIG_IDE is not set
+CONFIG_IDE=y
+
+#
+# Please see Documentation/ide/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+CONFIG_IDE_GD=y
+CONFIG_IDE_GD_ATA=y
+# CONFIG_IDE_GD_ATAPI is not set
+CONFIG_BLK_DEV_IDECS=y
+# CONFIG_BLK_DEV_IDECD is not set
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_PROC_FS=y
+
+#
+# IDE chipset support/bugfixes
+#
+# CONFIG_BLK_DEV_PLATFORM is not set
+
+#
+# PCI IDE chipsets support
+#
+# CONFIG_BLK_DEV_GENERIC is not set
+# CONFIG_BLK_DEV_OPTI621 is not set
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_JMICRON is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8172 is not set
+# CONFIG_BLK_DEV_IT8213 is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
+# CONFIG_BLK_DEV_IDEDMA is not set
 
 #
 # SCSI device support
@@ -570,10 +662,6 @@ CONFIG_BLK_DEV_SR=y
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 # CONFIG_CHR_DEV_SG is not set
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -590,6 +678,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 # CONFIG_SCSI_SRP_ATTRS is not set
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -598,6 +687,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -617,7 +707,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -630,6 +719,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_NSP32 is not set
 # CONFIG_SCSI_DEBUG is not set
 # CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
 # CONFIG_SCSI_DH is not set
 # CONFIG_SCSI_OSD_INITIATOR is not set
 CONFIG_ATA=y
@@ -647,14 +737,17 @@ CONFIG_SATA_SIL24=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=m
 CONFIG_BONDING=m
 # CONFIG_MACVLAN is not set
@@ -701,6 +794,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -720,8 +814,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -748,6 +844,7 @@ CONFIG_GIANFAR=y
 # CONFIG_USB_PEGASUS is not set
 # CONFIG_USB_RTL8150 is not set
 # CONFIG_USB_USBNET is not set
+# CONFIG_NET_PCMCIA is not set
 # CONFIG_WAN is not set
 # CONFIG_FDDI is not set
 # CONFIG_HIPPI is not set
@@ -827,6 +924,7 @@ CONFIG_DEVKMEM=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 # CONFIG_SERIAL_8250_PCI is not set
+# CONFIG_SERIAL_8250_CS is not set
 CONFIG_SERIAL_8250_NR_UARTS=2
 CONFIG_SERIAL_8250_RUNTIME_UARTS=2
 # CONFIG_SERIAL_8250_EXTENDED is not set
@@ -849,6 +947,14 @@ CONFIG_HW_RANDOM=y
 CONFIG_NVRAM=y
 # CONFIG_R3964 is not set
 # CONFIG_APPLICOM is not set
+
+#
+# PCMCIA character devices
+#
+# CONFIG_SYNCLINK_CS is not set
+# CONFIG_CARDMAN_4000 is not set
+# CONFIG_CARDMAN_4040 is not set
+# CONFIG_IPWIRELESS is not set
 # CONFIG_RAW_DRIVER is not set
 # CONFIG_TCG_TPM is not set
 CONFIG_DEVPORT=y
@@ -912,13 +1018,17 @@ CONFIG_DS1682=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -997,6 +1107,7 @@ CONFIG_SENSORS_LM92=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1052,24 +1163,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1114,7 +1210,7 @@ CONFIG_HID_BELKIN=y
 CONFIG_HID_CHERRY=y
 CONFIG_HID_CHICONY=y
 CONFIG_HID_CYPRESS=y
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 CONFIG_HID_EZKEY=y
 # CONFIG_HID_KYE is not set
 CONFIG_HID_GYRATION=y
@@ -1131,10 +1227,11 @@ CONFIG_HID_PETALYNX=y
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-# CONFIG_THRUSTMASTER_FF is not set
-# CONFIG_ZEROPLUS_FF is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1160,6 +1257,7 @@ CONFIG_USB=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1288,6 +1386,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 CONFIG_RTC_DRV_RX8581=y
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1315,6 +1414,10 @@ CONFIG_RTC_DRV_RX8581=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1336,10 +1439,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1419,6 +1524,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1508,6 +1614,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1531,23 +1638,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_PREEMPT_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
-- 
GitLab


From 34466c5be4dd1490acf98e6d2ff8f3728d8ca5c1 Mon Sep 17 00:00:00 2001
From: Kumar Gala <galak@kernel.crashing.org>
Date: Wed, 29 Jul 2009 23:34:01 -0500
Subject: [PATCH 0302/1153] powerpc: Update defconfigs for embedded 6xx/7xxx,
 8xx, 8{3,5,6}xxx

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 arch/powerpc/configs/83xx/asp8347_defconfig   | 106 ++++++----
 arch/powerpc/configs/83xx/kmeter1_defconfig   | 176 ++++++++++------
 .../configs/83xx/mpc8313_rdb_defconfig        | 168 ++++++++++-----
 .../configs/83xx/mpc8315_rdb_defconfig        | 168 ++++++++++-----
 .../configs/83xx/mpc832x_mds_defconfig        | 111 +++++-----
 .../configs/83xx/mpc832x_rdb_defconfig        | 120 ++++++-----
 .../configs/83xx/mpc834x_itx_defconfig        | 114 ++++++-----
 .../configs/83xx/mpc834x_itxgp_defconfig      | 114 ++++++-----
 .../configs/83xx/mpc834x_mds_defconfig        | 104 ++++++----
 .../configs/83xx/mpc836x_mds_defconfig        | 111 +++++-----
 .../configs/83xx/mpc836x_rdk_defconfig        | 104 ++++++----
 .../configs/83xx/mpc837x_mds_defconfig        | 110 +++++-----
 .../configs/83xx/mpc837x_rdb_defconfig        | 162 ++++++++++-----
 arch/powerpc/configs/83xx/sbc834x_defconfig   | 103 ++++++----
 arch/powerpc/configs/85xx/ksi8560_defconfig   |  93 ++++++---
 .../configs/85xx/mpc8540_ads_defconfig        |  91 ++++++---
 .../configs/85xx/mpc8560_ads_defconfig        |  99 +++++----
 .../configs/85xx/mpc85xx_cds_defconfig        |  99 +++++----
 arch/powerpc/configs/85xx/sbc8548_defconfig   |  96 +++++----
 arch/powerpc/configs/85xx/sbc8560_defconfig   |  91 ++++++---
 arch/powerpc/configs/85xx/socrates_defconfig  | 165 ++++++++++-----
 arch/powerpc/configs/85xx/stx_gp3_defconfig   | 119 +++++++----
 arch/powerpc/configs/85xx/tqm8540_defconfig   | 100 +++++----
 arch/powerpc/configs/85xx/tqm8541_defconfig   | 101 +++++----
 arch/powerpc/configs/85xx/tqm8548_defconfig   | 100 +++++----
 arch/powerpc/configs/85xx/tqm8555_defconfig   | 101 +++++----
 arch/powerpc/configs/85xx/tqm8560_defconfig   | 101 +++++----
 .../configs/85xx/xes_mpc85xx_defconfig        | 118 ++++++-----
 arch/powerpc/configs/86xx/gef_ppc9a_defconfig |   7 +-
 .../powerpc/configs/86xx/gef_sbc310_defconfig |   7 +-
 .../powerpc/configs/86xx/gef_sbc610_defconfig | 130 +++++++-----
 .../configs/86xx/mpc8610_hpcd_defconfig       | 118 +++++++----
 .../configs/86xx/mpc8641_hpcn_defconfig       | 186 ++++++++---------
 arch/powerpc/configs/86xx/sbc8641d_defconfig  | 112 ++++++----
 arch/powerpc/configs/adder875_defconfig       |  97 +++++----
 arch/powerpc/configs/c2k_defconfig            | 121 ++++++-----
 arch/powerpc/configs/ep8248e_defconfig        |  97 +++++----
 arch/powerpc/configs/ep88xc_defconfig         |  91 ++++++---
 arch/powerpc/configs/linkstation_defconfig    | 116 +++++++----
 arch/powerpc/configs/mgcoge_defconfig         |  97 +++++----
 arch/powerpc/configs/mgsuvd_defconfig         |  89 ++++----
 arch/powerpc/configs/mpc7448_hpc2_defconfig   | 103 +++++-----
 arch/powerpc/configs/mpc8272_ads_defconfig    | 104 ++++++----
 arch/powerpc/configs/mpc83xx_defconfig        | 162 ++++++++++-----
 arch/powerpc/configs/mpc85xx_defconfig        | 193 ++++++++----------
 arch/powerpc/configs/mpc85xx_smp_defconfig    | 193 ++++++++----------
 arch/powerpc/configs/mpc866_ads_defconfig     |  92 +++++----
 arch/powerpc/configs/mpc86xx_defconfig        | 186 ++++++++---------
 arch/powerpc/configs/mpc885_ads_defconfig     |  91 ++++++---
 arch/powerpc/configs/pq2fads_defconfig        | 110 ++++++----
 arch/powerpc/configs/prpmc2800_defconfig      | 158 +++++++++-----
 arch/powerpc/configs/storcenter_defconfig     | 108 +++++-----
 52 files changed, 3639 insertions(+), 2374 deletions(-)

diff --git a/arch/powerpc/configs/83xx/asp8347_defconfig b/arch/powerpc/configs/83xx/asp8347_defconfig
index 27893971377..a2df0635b6d 100644
--- a/arch/powerpc/configs/83xx/asp8347_defconfig
+++ b/arch/powerpc/configs/83xx/asp8347_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:05 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:02 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 CONFIG_FSL_EMB_PERFMON=y
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,6 +56,7 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 CONFIG_REDBOOT=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
@@ -60,6 +64,7 @@ CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -108,7 +113,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -121,9 +125,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -136,6 +147,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -148,7 +163,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -190,6 +205,7 @@ CONFIG_PPC_83xx=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 CONFIG_ASP834x=y
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC834x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -235,6 +251,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -255,9 +272,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -383,7 +401,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -490,6 +512,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -525,7 +548,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -545,14 +570,17 @@ CONFIG_HAVE_IDE=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -599,6 +627,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -618,8 +647,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -786,13 +817,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -847,6 +882,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -900,24 +936,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -960,6 +981,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1069,6 +1091,7 @@ CONFIG_RTC_DRV_DS1374=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1096,6 +1119,10 @@ CONFIG_RTC_DRV_DS1374=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1115,10 +1142,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1192,6 +1221,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1287,6 +1317,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1312,22 +1343,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/kmeter1_defconfig b/arch/powerpc/configs/83xx/kmeter1_defconfig
index bf0853f29f3..93ebd443a18 100644
--- a/arch/powerpc/configs/83xx/kmeter1_defconfig
+++ b/arch/powerpc/configs/83xx/kmeter1_defconfig
@@ -1,25 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28
-# Fri Apr  3 10:34:33 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:03 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
+CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -30,21 +33,22 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
 CONFIG_EARLY_PRINTK=y
 CONFIG_GENERIC_NVRAM=y
-CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
 CONFIG_ARCH_MAY_HAVE_PC_FDC=y
 CONFIG_PPC_OF=y
 CONFIG_OF=y
@@ -52,11 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
+CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -71,19 +78,30 @@ CONFIG_LOCALVERSION_AUTO=y
 CONFIG_SYSVIPC=y
 CONFIG_SYSVIPC_SYSCTL=y
 CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
 # CONFIG_BSD_PROCESS_ACCT is not set
 # CONFIG_TASKSTATS is not set
 # CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
 # CONFIG_IKCONFIG is not set
 CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CGROUPS is not set
 # CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
 # CONFIG_SYSFS_DEPRECATED_V2 is not set
 # CONFIG_RELAY is not set
 # CONFIG_NAMESPACES is not set
 # CONFIG_BLK_DEV_INITRD is not set
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
@@ -93,17 +111,23 @@ CONFIG_KALLSYMS_ALL=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
 CONFIG_ELF_CORE=y
-CONFIG_COMPAT_BRK=y
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
 CONFIG_EPOLL=y
 CONFIG_SIGNALFD=y
 CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
+CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
 # CONFIG_SLOB is not set
@@ -116,10 +140,15 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
+# CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
 CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
 CONFIG_BASE_SMALL=0
 CONFIG_MODULES=y
 # CONFIG_MODULE_FORCE_LOAD is not set
@@ -127,11 +156,8 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODULE_FORCE_UNLOAD is not set
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
-CONFIG_KMOD=y
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -147,14 +173,11 @@ CONFIG_IOSCHED_NOOP=y
 # CONFIG_DEFAULT_CFQ is not set
 CONFIG_DEFAULT_NOOP=y
 CONFIG_DEFAULT_IOSCHED="noop"
-CONFIG_CLASSIC_RCU=y
 # CONFIG_FREEZER is not set
 
 #
 # Platform support
 #
-CONFIG_PPC_MULTIPLATFORM=y
-CONFIG_CLASSIC32=y
 # CONFIG_PPC_CHRP is not set
 # CONFIG_MPC5121_ADS is not set
 # CONFIG_MPC5121_GENERIC is not set
@@ -179,6 +202,8 @@ CONFIG_PPC_83xx=y
 CONFIG_KMETER1=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
+# CONFIG_AMIGAONE is not set
+CONFIG_PPC_OF_BOOT_TRAMPOLINE=y
 CONFIG_IPIC=y
 # CONFIG_MPIC is not set
 # CONFIG_MPIC_WEIRD is not set
@@ -194,6 +219,8 @@ CONFIG_IPIC=y
 CONFIG_QUICC_ENGINE=y
 # CONFIG_QE_GPIO is not set
 # CONFIG_FSL_ULI1575 is not set
+# CONFIG_SIMPLE_GPIO is not set
+# CONFIG_MCU_MPC8349EMITX is not set
 
 #
 # Kernel options
@@ -212,16 +239,17 @@ CONFIG_SCHED_HRTICK=y
 # CONFIG_PREEMPT_NONE is not set
 # CONFIG_PREEMPT_VOLUNTARY is not set
 CONFIG_PREEMPT=y
-# CONFIG_PREEMPT_RCU is not set
 CONFIG_BINFMT_ELF=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
 # CONFIG_KEXEC is not set
+# CONFIG_CRASH_DUMP is not set
 CONFIG_ARCH_FLATMEM_ENABLE=y
 CONFIG_ARCH_POPULATES_NODE_MAP=y
 CONFIG_SELECT_MEMORY_MODEL=y
@@ -233,12 +261,17 @@ CONFIG_FLAT_NODE_MEM_MAP=y
 CONFIG_PAGEFLAGS_EXTENDED=y
 CONFIG_SPLIT_PTLOCK_CPUS=4
 CONFIG_MIGRATION=y
-# CONFIG_RESOURCES_64BIT is not set
 # CONFIG_PHYS_ADDR_T_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_PPC_4K_PAGES=y
+# CONFIG_PPC_16K_PAGES is not set
+# CONFIG_PPC_64K_PAGES is not set
+# CONFIG_PPC_256K_PAGES is not set
 CONFIG_FORCE_MAX_ZONEORDER=11
 CONFIG_PROC_DEVICETREE=y
 # CONFIG_CMDLINE_BOOL is not set
@@ -331,7 +364,10 @@ CONFIG_LLC=m
 # CONFIG_LAPB is not set
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
 
 #
 # Network testing
@@ -342,8 +378,8 @@ CONFIG_LLC=m
 # CONFIG_IRDA is not set
 # CONFIG_BT is not set
 # CONFIG_AF_RXRPC is not set
-# CONFIG_PHONET is not set
 # CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
 
@@ -362,6 +398,7 @@ CONFIG_MTD=y
 # CONFIG_MTD_DEBUG is not set
 CONFIG_MTD_CONCAT=y
 CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
 # CONFIG_MTD_REDBOOT_PARTS is not set
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_OF_PARTS=y
@@ -430,6 +467,11 @@ CONFIG_MTD_PHRAM=y
 # CONFIG_MTD_NAND is not set
 # CONFIG_MTD_ONENAND is not set
 
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
 #
 # UBI - Unsorted block images
 #
@@ -445,7 +487,6 @@ CONFIG_MTD_UBI_DEBUG=y
 # CONFIG_MTD_UBI_DEBUG_MSG is not set
 # CONFIG_MTD_UBI_DEBUG_PARANOID is not set
 # CONFIG_MTD_UBI_DEBUG_DISABLE_BGT is not set
-# CONFIG_MTD_UBI_DEBUG_USERSPACE_IO is not set
 # CONFIG_MTD_UBI_DEBUG_EMULATE_BITFLIPS is not set
 # CONFIG_MTD_UBI_DEBUG_EMULATE_WRITE_FAILURES is not set
 # CONFIG_MTD_UBI_DEBUG_EMULATE_ERASE_FAILURES is not set
@@ -459,6 +500,7 @@ CONFIG_MTD_UBI_DEBUG=y
 # CONFIG_MTD_UBI_DEBUG_MSG_IO is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -505,10 +547,15 @@ CONFIG_MARVELL_PHY=y
 # CONFIG_BROADCOM_PHY is not set
 # CONFIG_ICPLUS_PHY is not set
 # CONFIG_REALTEK_PHY is not set
+# CONFIG_NATIONAL_PHY is not set
+# CONFIG_STE10XP is not set
+# CONFIG_LSI_ET1011C_PHY is not set
 # CONFIG_FIXED_PHY is not set
 # CONFIG_MDIO_BITBANG is not set
 CONFIG_NET_ETHERNET=y
 CONFIG_MII=y
+# CONFIG_ETHOC is not set
+# CONFIG_DNET is not set
 # CONFIG_IBM_NEW_EMAC_ZMII is not set
 # CONFIG_IBM_NEW_EMAC_RGMII is not set
 # CONFIG_IBM_NEW_EMAC_TAH is not set
@@ -517,11 +564,12 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_NETDEV_1000=y
+CONFIG_FSL_PQ_MDIO=y
 # CONFIG_GIANFAR is not set
 CONFIG_UCC_GETH=y
 # CONFIG_UGETH_MAGIC_PACKET is not set
-# CONFIG_UGETH_FILTERING is not set
 # CONFIG_UGETH_TX_ON_DEMAND is not set
 # CONFIG_MV643XX_ETH is not set
 # CONFIG_NETDEV_10000 is not set
@@ -531,7 +579,10 @@ CONFIG_UCC_GETH=y
 #
 # CONFIG_WLAN_PRE80211 is not set
 # CONFIG_WLAN_80211 is not set
-# CONFIG_IWLWIFI_LEDS is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
 CONFIG_WAN=y
 CONFIG_HDLC=y
 # CONFIG_HDLC_RAW is not set
@@ -543,8 +594,6 @@ CONFIG_HDLC=y
 #
 # X.25/LAPB support is disabled
 #
-CONFIG_HDLC_KM=y
-CONFIG_FS_UCC_HDLC=y
 # CONFIG_DLCI is not set
 CONFIG_PPP=y
 CONFIG_PPP_MULTILINK=y
@@ -600,16 +649,18 @@ CONFIG_SERIAL_CORE_CONSOLE=y
 # CONFIG_SERIAL_OF_PLATFORM is not set
 # CONFIG_SERIAL_QE is not set
 CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
 CONFIG_LEGACY_PTYS=y
 CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_HVC_UDBG is not set
 # CONFIG_IPMI_HANDLER is not set
 CONFIG_HW_RANDOM=y
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
 # CONFIG_NVRAM is not set
 # CONFIG_GEN_RTC is not set
 # CONFIG_R3964 is not set
 # CONFIG_RAW_DRIVER is not set
 # CONFIG_TCG_TPM is not set
-CONFIG_BOOTCOUNT=y
 CONFIG_I2C=y
 CONFIG_I2C_BOARDINFO=y
 CONFIG_I2C_CHARDEV=y
@@ -642,20 +693,20 @@ CONFIG_I2C_MPC=y
 # Miscellaneous I2C Chip support
 #
 # CONFIG_DS1682 is not set
-# CONFIG_AT24 is not set
-# CONFIG_SENSORS_EEPROM is not set
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_PCF8591 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
-# CONFIG_MCU_MPC8349EMITX is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -677,27 +728,15 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_CORE is not set
 # CONFIG_MFD_SM501 is not set
 # CONFIG_HTC_PASIC3 is not set
+# CONFIG_TWL4030_CORE is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_PMIC_DA903X is not set
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -720,11 +759,16 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_EDAC is not set
 # CONFIG_RTC_CLASS is not set
 # CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
 CONFIG_UIO=y
 # CONFIG_UIO_PDRV is not set
 # CONFIG_UIO_PDRV_GENIRQ is not set
 # CONFIG_UIO_SMX is not set
 # CONFIG_UIO_SERCOS3 is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -736,9 +780,12 @@ CONFIG_UIO=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -747,6 +794,11 @@ CONFIG_INOTIFY_USER=y
 # CONFIG_AUTOFS4_FS is not set
 # CONFIG_FUSE_FS is not set
 
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
 #
 # CD-ROM/DVD Filesystems
 #
@@ -772,10 +824,7 @@ CONFIG_TMPFS=y
 # CONFIG_TMPFS_POSIX_ACL is not set
 # CONFIG_HUGETLB_PAGE is not set
 # CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
+CONFIG_MISC_FILESYSTEMS=y
 # CONFIG_ADFS_FS is not set
 # CONFIG_AFFS_FS is not set
 # CONFIG_HFS_FS is not set
@@ -796,6 +845,7 @@ CONFIG_JFFS2_RTIME=y
 # CONFIG_JFFS2_RUBIN is not set
 # CONFIG_UBIFS_FS is not set
 # CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
 # CONFIG_VXFS_FS is not set
 # CONFIG_MINIX_FS is not set
 # CONFIG_OMFS_FS is not set
@@ -804,6 +854,7 @@ CONFIG_JFFS2_RTIME=y
 # CONFIG_ROMFS_FS is not set
 # CONFIG_SYSV_FS is not set
 # CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
 CONFIG_NETWORK_FILESYSTEMS=y
 CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
@@ -815,7 +866,6 @@ CONFIG_LOCKD=y
 CONFIG_LOCKD_V4=y
 CONFIG_NFS_COMMON=y
 CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_REGISTER_V4 is not set
 # CONFIG_RPCSEC_GSS_KRB5 is not set
 # CONFIG_RPCSEC_GSS_SPKM3 is not set
 # CONFIG_SMB_FS is not set
@@ -845,11 +895,13 @@ CONFIG_PARTITION_ADVANCED=y
 # CONFIG_DLM is not set
 CONFIG_UCC_FAST=y
 CONFIG_UCC=y
+# CONFIG_BINARY_PRINTF is not set
 
 #
 # Library routines
 #
 CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
 # CONFIG_CRC_CCITT is not set
 # CONFIG_CRC16 is not set
 # CONFIG_CRC_T10DIF is not set
@@ -859,11 +911,12 @@ CONFIG_CRC32=y
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=y
 CONFIG_ZLIB_DEFLATE=y
-CONFIG_PLIST=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
+CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -883,13 +936,18 @@ CONFIG_DEBUG_FS=y
 # CONFIG_LATENCYTOP is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
 CONFIG_HAVE_FUNCTION_TRACER=y
-
-#
-# Tracers
-#
-# CONFIG_DYNAMIC_PRINTK_DEBUG is not set
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_DYNAMIC_DEBUG is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
+CONFIG_PRINT_STACK_DEPTH=64
+# CONFIG_PPC_EMULATED_STATS is not set
 # CONFIG_IRQSTACKS is not set
 # CONFIG_VIRQ_DEBUG is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig b/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig
index c5c0fe71a43..ff33a7db2ea 100644
--- a/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig
+++ b/arch/powerpc/configs/83xx/mpc8313_rdb_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:06 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:04 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -120,9 +124,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -189,6 +204,7 @@ CONFIG_MPC831x_RDB=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC831x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -254,9 +271,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -383,7 +401,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -503,6 +525,7 @@ CONFIG_MTD_NAND_FSL_ELBC=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
 CONFIG_OF_SPI=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -539,7 +562,9 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_AT25 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -562,10 +587,6 @@ CONFIG_SCSI_PROC_FS=y
 # CONFIG_BLK_DEV_SR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -583,6 +604,7 @@ CONFIG_SCSI_SPI_ATTRS=y
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -591,6 +613,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -610,7 +633,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_QLOGIC_1280 is not set
@@ -643,14 +665,17 @@ CONFIG_MD_RAID1=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -714,6 +739,8 @@ CONFIG_E100=y
 # CONFIG_SMSC9420 is not set
 # CONFIG_SUNDANCE is not set
 # CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
 # CONFIG_VIA_RHINE is not set
 # CONFIG_SC92031 is not set
 # CONFIG_ATL2 is not set
@@ -735,8 +762,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -924,7 +953,6 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -938,13 +966,18 @@ CONFIG_SPI_MASTER=y
 # SPI Master Controller Drivers
 #
 CONFIG_SPI_BITBANG=y
-CONFIG_SPI_MPC83xx=y
+# CONFIG_SPI_MPC8xxx is not set
 
 #
 # SPI Protocol Masters
 #
 # CONFIG_SPI_SPIDEV is not set
 # CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -1002,6 +1035,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1056,24 +1090,10 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1135,6 +1155,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1144,9 +1165,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
+CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PCI=y
 CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1235,8 +1256,9 @@ CONFIG_USB_GADGET_SELECTED=y
 # CONFIG_USB_GADGET_OMAP is not set
 # CONFIG_USB_GADGET_PXA25X is not set
 # CONFIG_USB_GADGET_PXA27X is not set
-# CONFIG_USB_GADGET_S3C2410 is not set
+# CONFIG_USB_GADGET_S3C_HSOTG is not set
 # CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
 # CONFIG_USB_GADGET_M66592 is not set
 # CONFIG_USB_GADGET_AMD5536UDC is not set
 # CONFIG_USB_GADGET_FSL_QE is not set
@@ -1244,9 +1266,11 @@ CONFIG_USB_GADGET_SELECTED=y
 CONFIG_USB_GADGET_NET2280=y
 CONFIG_USB_NET2280=y
 # CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LANGWELL is not set
 # CONFIG_USB_GADGET_DUMMY_HCD is not set
 CONFIG_USB_GADGET_DUALSPEED=y
 # CONFIG_USB_ZERO is not set
+# CONFIG_USB_AUDIO is not set
 CONFIG_USB_ETH=y
 CONFIG_USB_ETH_RNDIS=y
 # CONFIG_USB_GADGETFS is not set
@@ -1298,6 +1322,7 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1332,6 +1357,10 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1351,10 +1380,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1428,6 +1459,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1464,7 +1496,46 @@ CONFIG_MSDOS_PARTITION=y
 # CONFIG_KARMA_PARTITION is not set
 # CONFIG_EFI_PARTITION is not set
 # CONFIG_SYSV68_PARTITION is not set
-# CONFIG_NLS is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
 # CONFIG_DLM is not set
 # CONFIG_BINARY_PRINTF is not set
 
@@ -1488,6 +1559,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1518,6 +1590,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1529,7 +1604,6 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1543,16 +1617,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1560,6 +1633,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig b/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig
index af4952feba3..76237d46670 100644
--- a/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig
+++ b/arch/powerpc/configs/83xx/mpc8315_rdb_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:06 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:05 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -120,9 +124,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -189,6 +204,7 @@ CONFIG_MPC831x_RDB=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC831x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -254,9 +271,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -383,7 +401,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -503,6 +525,7 @@ CONFIG_MTD_NAND_IDS=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
 CONFIG_OF_SPI=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -539,7 +562,9 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_AT25 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -562,10 +587,6 @@ CONFIG_SCSI_PROC_FS=y
 # CONFIG_BLK_DEV_SR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -583,6 +604,7 @@ CONFIG_SCSI_SPI_ATTRS=y
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -591,6 +613,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -610,7 +633,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -704,14 +726,17 @@ CONFIG_MD_RAID1=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -775,6 +800,8 @@ CONFIG_E100=y
 # CONFIG_SMSC9420 is not set
 # CONFIG_SUNDANCE is not set
 # CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
 # CONFIG_VIA_RHINE is not set
 # CONFIG_SC92031 is not set
 # CONFIG_ATL2 is not set
@@ -796,8 +823,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -985,7 +1014,6 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -999,13 +1027,18 @@ CONFIG_SPI_MASTER=y
 # SPI Master Controller Drivers
 #
 CONFIG_SPI_BITBANG=y
-CONFIG_SPI_MPC83xx=y
+# CONFIG_SPI_MPC8xxx is not set
 
 #
 # SPI Protocol Masters
 #
 # CONFIG_SPI_SPIDEV is not set
 # CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -1063,6 +1096,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1117,24 +1151,10 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1196,6 +1216,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1205,9 +1226,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
+CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PCI=y
 CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1296,8 +1317,9 @@ CONFIG_USB_GADGET_SELECTED=y
 # CONFIG_USB_GADGET_OMAP is not set
 # CONFIG_USB_GADGET_PXA25X is not set
 # CONFIG_USB_GADGET_PXA27X is not set
-# CONFIG_USB_GADGET_S3C2410 is not set
+# CONFIG_USB_GADGET_S3C_HSOTG is not set
 # CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
 # CONFIG_USB_GADGET_M66592 is not set
 # CONFIG_USB_GADGET_AMD5536UDC is not set
 # CONFIG_USB_GADGET_FSL_QE is not set
@@ -1305,9 +1327,11 @@ CONFIG_USB_GADGET_SELECTED=y
 CONFIG_USB_GADGET_NET2280=y
 CONFIG_USB_NET2280=y
 # CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LANGWELL is not set
 # CONFIG_USB_GADGET_DUMMY_HCD is not set
 CONFIG_USB_GADGET_DUALSPEED=y
 # CONFIG_USB_ZERO is not set
+# CONFIG_USB_AUDIO is not set
 CONFIG_USB_ETH=y
 CONFIG_USB_ETH_RNDIS=y
 # CONFIG_USB_GADGETFS is not set
@@ -1359,6 +1383,7 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1393,6 +1418,10 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1412,10 +1441,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1489,6 +1520,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1525,7 +1557,46 @@ CONFIG_MSDOS_PARTITION=y
 # CONFIG_KARMA_PARTITION is not set
 # CONFIG_EFI_PARTITION is not set
 # CONFIG_SYSV68_PARTITION is not set
-# CONFIG_NLS is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
 # CONFIG_DLM is not set
 # CONFIG_BINARY_PRINTF is not set
 
@@ -1549,6 +1620,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1579,6 +1651,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1590,7 +1665,6 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1604,16 +1678,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1621,6 +1694,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/83xx/mpc832x_mds_defconfig b/arch/powerpc/configs/83xx/mpc832x_mds_defconfig
index 8c8f660b4fc..e0e36a11340 100644
--- a/arch/powerpc/configs/83xx/mpc832x_mds_defconfig
+++ b/arch/powerpc/configs/83xx/mpc832x_mds_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:07 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:06 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -120,9 +124,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -189,6 +204,7 @@ CONFIG_MPC832x_MDS=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC832x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -235,6 +251,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -255,9 +272,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -383,7 +401,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -404,6 +426,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -438,7 +461,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -461,10 +486,6 @@ CONFIG_SCSI_PROC_FS=y
 # CONFIG_BLK_DEV_SR is not set
 # CONFIG_CHR_DEV_SG is not set
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -482,6 +503,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -490,6 +512,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -509,7 +532,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_QLOGIC_1280 is not set
@@ -532,14 +554,17 @@ CONFIG_SCSI_LOWLEVEL=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -586,6 +611,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -605,11 +631,13 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 # CONFIG_GIANFAR is not set
 CONFIG_UCC_GETH=y
 # CONFIG_UGETH_MAGIC_PACKET is not set
 # CONFIG_UGETH_TX_ON_DEMAND is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -787,13 +815,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -848,6 +880,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -896,23 +929,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -996,6 +1015,7 @@ CONFIG_RTC_DRV_DS1374=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1023,6 +1043,10 @@ CONFIG_RTC_DRV_DS1374=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1042,10 +1066,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1108,6 +1134,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1165,6 +1192,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1190,22 +1218,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig b/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig
index 227dbba7679..4f27d454822 100644
--- a/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig
+++ b/arch/powerpc/configs/83xx/mpc832x_rdb_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:08 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:07 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -120,9 +124,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -189,6 +204,7 @@ CONFIG_MPC832x_RDB=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC832x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -235,6 +251,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -255,9 +272,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -383,7 +401,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -405,6 +427,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
 CONFIG_OF_SPI=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -441,7 +464,9 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_AT25 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -464,10 +489,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 # CONFIG_CHR_DEV_SG is not set
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -485,6 +506,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -493,6 +515,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -512,7 +535,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_QLOGIC_1280 is not set
@@ -535,14 +557,17 @@ CONFIG_SCSI_LOWLEVEL=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -590,6 +615,8 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -609,11 +636,13 @@ CONFIG_E1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 # CONFIG_GIANFAR is not set
 CONFIG_UCC_GETH=y
 # CONFIG_UGETH_MAGIC_PACKET is not set
 # CONFIG_UGETH_TX_ON_DEMAND is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -804,7 +833,6 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -817,13 +845,18 @@ CONFIG_SPI_MASTER=y
 # SPI Master Controller Drivers
 #
 CONFIG_SPI_BITBANG=y
-CONFIG_SPI_MPC83xx=y
+# CONFIG_SPI_MPC8xxx is not set
 
 #
 # SPI Protocol Masters
 #
 # CONFIG_SPI_SPIDEV is not set
 # CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -881,6 +914,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -935,24 +969,10 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1014,6 +1034,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1023,9 +1044,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
+CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PCI=y
 CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1127,6 +1148,8 @@ CONFIG_MMC_BLOCK_BOUNCE=y
 # CONFIG_MMC_WBSD is not set
 # CONFIG_MMC_TIFM_SD is not set
 CONFIG_MMC_SPI=y
+# CONFIG_MMC_CB710 is not set
+# CONFIG_MMC_VIA_SDMMC is not set
 # CONFIG_MEMSTICK is not set
 # CONFIG_NEW_LEDS is not set
 # CONFIG_ACCESSIBILITY is not set
@@ -1136,6 +1159,10 @@ CONFIG_MMC_SPI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1155,10 +1182,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1224,6 +1253,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1325,6 +1355,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1350,22 +1381,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/mpc834x_itx_defconfig b/arch/powerpc/configs/83xx/mpc834x_itx_defconfig
index 24ee7fcac87..648dac0c9d8 100644
--- a/arch/powerpc/configs/83xx/mpc834x_itx_defconfig
+++ b/arch/powerpc/configs/83xx/mpc834x_itx_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:09 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:07 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -120,9 +124,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -189,6 +204,7 @@ CONFIG_MPC834x_ITX=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC834x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -254,9 +271,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -365,6 +382,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -382,7 +400,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -487,6 +509,7 @@ CONFIG_MTD_PHYSMAP=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
 CONFIG_OF_SPI=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -523,7 +546,9 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_AT25 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -594,10 +619,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -615,6 +636,7 @@ CONFIG_SCSI_SPI_ATTRS=y
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -623,6 +645,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -642,7 +665,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -737,14 +759,17 @@ CONFIG_MD_RAID1=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -791,8 +816,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -960,7 +987,6 @@ CONFIG_I2C_MPC=y
 CONFIG_SENSORS_PCF8574=y
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -973,13 +999,18 @@ CONFIG_SPI_MASTER=y
 # SPI Master Controller Drivers
 #
 CONFIG_SPI_BITBANG=y
-CONFIG_SPI_MPC83xx=y
+# CONFIG_SPI_MPC8xxx is not set
 
 #
 # SPI Protocol Masters
 #
 # CONFIG_SPI_SPIDEV is not set
 # CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -1026,24 +1057,10 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1085,6 +1102,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1208,6 +1226,7 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1242,6 +1261,10 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1261,10 +1284,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1331,6 +1356,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1429,6 +1455,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1454,22 +1481,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig b/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig
index 7f39543205a..bf6deb831dc 100644
--- a/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig
+++ b/arch/powerpc/configs/83xx/mpc834x_itxgp_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:10 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:08 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -120,9 +124,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -189,6 +204,7 @@ CONFIG_MPC834x_ITX=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC834x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -254,9 +271,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -365,6 +382,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -382,7 +400,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -487,6 +509,7 @@ CONFIG_MTD_PHYSMAP=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
 CONFIG_OF_SPI=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -523,7 +546,9 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_AT25 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -546,10 +571,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -567,6 +588,7 @@ CONFIG_SCSI_SPI_ATTRS=y
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -575,6 +597,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -594,7 +617,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_QLOGIC_1280 is not set
@@ -617,14 +639,17 @@ CONFIG_SCSI_LOWLEVEL=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -671,8 +696,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -840,7 +867,6 @@ CONFIG_I2C_MPC=y
 CONFIG_SENSORS_PCF8574=y
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -853,13 +879,18 @@ CONFIG_SPI_MASTER=y
 # SPI Master Controller Drivers
 #
 CONFIG_SPI_BITBANG=y
-CONFIG_SPI_MPC83xx=y
+# CONFIG_SPI_MPC8xxx is not set
 
 #
 # SPI Protocol Masters
 #
 # CONFIG_SPI_SPIDEV is not set
 # CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -906,24 +937,10 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -965,6 +982,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1087,6 +1105,7 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1121,6 +1140,10 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1140,10 +1163,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1210,6 +1235,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1308,6 +1334,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1333,22 +1360,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/mpc834x_mds_defconfig b/arch/powerpc/configs/83xx/mpc834x_mds_defconfig
index 1cd1fcac22c..3236c47712c 100644
--- a/arch/powerpc/configs/83xx/mpc834x_mds_defconfig
+++ b/arch/powerpc/configs/83xx/mpc834x_mds_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:11 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:09 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -120,9 +124,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -189,6 +204,7 @@ CONFIG_MPC834x_MDS=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC834x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -254,9 +271,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -365,6 +382,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -382,7 +400,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -403,6 +425,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -437,7 +460,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -457,14 +482,17 @@ CONFIG_HAVE_IDE=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -527,6 +555,7 @@ CONFIG_E100=y
 # CONFIG_SMSC9420 is not set
 # CONFIG_SUNDANCE is not set
 # CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
 # CONFIG_VIA_RHINE is not set
 # CONFIG_SC92031 is not set
 # CONFIG_ATL2 is not set
@@ -548,8 +577,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -724,13 +755,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -785,6 +820,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -833,23 +869,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -933,6 +955,7 @@ CONFIG_RTC_DRV_DS1374=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -960,6 +983,10 @@ CONFIG_RTC_DRV_DS1374=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -979,10 +1006,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1045,6 +1074,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1100,6 +1130,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1125,22 +1156,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/mpc836x_mds_defconfig b/arch/powerpc/configs/83xx/mpc836x_mds_defconfig
index ce5177393a0..8c5299d7481 100644
--- a/arch/powerpc/configs/83xx/mpc836x_mds_defconfig
+++ b/arch/powerpc/configs/83xx/mpc836x_mds_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:12 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:10 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -120,9 +124,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -135,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -147,7 +162,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -189,6 +204,7 @@ CONFIG_MPC836x_MDS=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
 # CONFIG_AMIGAONE is not set
@@ -233,6 +249,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -253,9 +270,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -364,6 +381,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -381,7 +399,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -485,6 +507,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -519,7 +542,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -542,10 +567,6 @@ CONFIG_SCSI_PROC_FS=y
 # CONFIG_BLK_DEV_SR is not set
 # CONFIG_CHR_DEV_SG is not set
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -563,6 +584,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -571,6 +593,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -590,7 +613,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_QLOGIC_1280 is not set
@@ -613,14 +635,17 @@ CONFIG_SCSI_LOWLEVEL=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -667,6 +692,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -686,11 +712,13 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 # CONFIG_GIANFAR is not set
 CONFIG_UCC_GETH=y
 # CONFIG_UGETH_MAGIC_PACKET is not set
 # CONFIG_UGETH_TX_ON_DEMAND is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -868,13 +896,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -929,6 +961,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -977,23 +1010,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1077,6 +1096,7 @@ CONFIG_RTC_DRV_DS1374=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1104,6 +1124,10 @@ CONFIG_RTC_DRV_DS1374=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1123,10 +1147,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1190,6 +1216,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1247,6 +1274,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1272,22 +1300,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig b/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig
index 7f1d1383a24..ff31667a890 100644
--- a/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig
+++ b/arch/powerpc/configs/83xx/mpc836x_rdk_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:13 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:12 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -54,12 +57,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -108,7 +113,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -121,9 +125,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -136,6 +147,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -148,7 +163,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -190,6 +205,7 @@ CONFIG_MPC836x_RDK=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
 # CONFIG_AMIGAONE is not set
@@ -233,6 +249,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -253,9 +270,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -366,6 +383,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -383,7 +401,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -498,6 +520,7 @@ CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
 CONFIG_OF_SPI=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -533,7 +556,9 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_AT25 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -553,14 +578,17 @@ CONFIG_HAVE_IDE=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -607,11 +635,13 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 # CONFIG_GIANFAR is not set
 CONFIG_UCC_GETH=y
 # CONFIG_UGETH_MAGIC_PACKET is not set
 # CONFIG_UGETH_TX_ON_DEMAND is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -777,7 +807,6 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -791,13 +820,18 @@ CONFIG_SPI_MASTER=y
 #
 CONFIG_SPI_BITBANG=y
 # CONFIG_SPI_GPIO is not set
-CONFIG_SPI_MPC83xx=y
+# CONFIG_SPI_MPC8xxx is not set
 
 #
 # SPI Protocol Masters
 #
 CONFIG_SPI_SPIDEV=y
 # CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -865,23 +899,10 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -990,6 +1011,10 @@ CONFIG_HID=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1009,10 +1034,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1086,6 +1113,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1145,6 +1173,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1170,22 +1199,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/mpc837x_mds_defconfig b/arch/powerpc/configs/83xx/mpc837x_mds_defconfig
index bf636fd560a..e285ec0fe95 100644
--- a/arch/powerpc/configs/83xx/mpc837x_mds_defconfig
+++ b/arch/powerpc/configs/83xx/mpc837x_mds_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:12 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:11 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -108,7 +113,6 @@ CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -121,8 +125,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -136,6 +147,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -148,7 +163,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -190,6 +205,7 @@ CONFIG_MPC837x_MDS=y
 # CONFIG_MPC837x_RDB is not set
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC837x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -254,9 +271,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -365,6 +382,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -382,7 +400,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -403,6 +425,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -437,7 +460,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -460,10 +485,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -481,6 +502,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -489,6 +511,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -508,7 +531,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -592,14 +614,17 @@ CONFIG_ATA_SFF=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -646,6 +671,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -665,8 +691,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -844,13 +872,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -905,6 +937,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -953,23 +986,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1026,6 +1045,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1045,10 +1068,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1111,6 +1136,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1170,6 +1196,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1193,22 +1220,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig b/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig
index fe6454eacbd..1ab3e4cd301 100644
--- a/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig
+++ b/arch/powerpc/configs/83xx/mpc837x_rdb_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:14 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:13 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -108,7 +113,6 @@ CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -121,8 +125,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -136,6 +147,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -148,7 +163,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -190,6 +205,7 @@ CONFIG_PPC_83xx=y
 CONFIG_MPC837x_RDB=y
 # CONFIG_SBC834x is not set
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC837x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -254,9 +271,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -360,6 +377,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -377,7 +395,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -398,6 +420,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -433,7 +456,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -456,10 +481,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -476,6 +497,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 # CONFIG_SCSI_SRP_ATTRS is not set
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -484,6 +506,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -503,7 +526,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -598,14 +620,17 @@ CONFIG_MD_RAID6_PQ=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -652,6 +677,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -671,8 +697,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -842,13 +870,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -903,6 +935,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -956,24 +989,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1011,7 +1029,7 @@ CONFIG_HID_BELKIN=y
 CONFIG_HID_CHERRY=y
 CONFIG_HID_CHICONY=y
 CONFIG_HID_CYPRESS=y
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 CONFIG_HID_EZKEY=y
 # CONFIG_HID_KYE is not set
 CONFIG_HID_GYRATION=y
@@ -1028,10 +1046,11 @@ CONFIG_HID_PETALYNX=y
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-CONFIG_THRUSTMASTER_FF=m
-CONFIG_ZEROPLUS_FF=m
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1057,6 +1076,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1141,6 +1161,10 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1160,10 +1184,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1226,6 +1252,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1262,7 +1289,46 @@ CONFIG_MSDOS_PARTITION=y
 # CONFIG_KARMA_PARTITION is not set
 # CONFIG_EFI_PARTITION is not set
 # CONFIG_SYSV68_PARTITION is not set
-# CONFIG_NLS is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
 # CONFIG_DLM is not set
 # CONFIG_BINARY_PRINTF is not set
 
@@ -1285,6 +1351,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1308,22 +1375,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/83xx/sbc834x_defconfig b/arch/powerpc/configs/83xx/sbc834x_defconfig
index fe08f672cb2..a592b5efdc4 100644
--- a/arch/powerpc/configs/83xx/sbc834x_defconfig
+++ b/arch/powerpc/configs/83xx/sbc834x_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:15 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:13 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,12 +56,14 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -107,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -120,8 +124,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -134,6 +145,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -146,7 +161,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -188,6 +203,7 @@ CONFIG_PPC_83xx=y
 # CONFIG_MPC837x_RDB is not set
 CONFIG_SBC834x=y
 # CONFIG_ASP834x is not set
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC834x=y
 # CONFIG_PPC_86xx is not set
 # CONFIG_EMBEDDED6xx is not set
@@ -232,6 +248,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -252,9 +269,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -363,6 +380,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -380,7 +398,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -401,6 +423,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -435,7 +458,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -455,14 +480,17 @@ CONFIG_HAVE_IDE=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -509,6 +537,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -528,8 +557,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -688,13 +719,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -749,6 +784,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -797,23 +833,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -851,6 +873,10 @@ CONFIG_HID=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -862,10 +888,12 @@ CONFIG_HID=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -928,6 +956,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -971,6 +1000,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -994,22 +1024,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/85xx/ksi8560_defconfig b/arch/powerpc/configs/85xx/ksi8560_defconfig
index 09146ddaa3c..ff04e1028f5 100644
--- a/arch/powerpc/configs/85xx/ksi8560_defconfig
+++ b/arch/powerpc/configs/85xx/ksi8560_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:16 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:14 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -108,7 +111,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -121,8 +123,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -136,6 +145,11 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -143,7 +157,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -176,6 +190,7 @@ CONFIG_MPC85xx=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 CONFIG_KSI8560=y
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -224,6 +239,7 @@ CONFIG_BINFMT_ELF=y
 CONFIG_BINFMT_MISC=y
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -242,9 +258,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -346,6 +362,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -363,7 +380,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -466,6 +487,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -520,7 +542,6 @@ CONFIG_IDE_PROC_FS=y
 # CONFIG_MD is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -560,6 +581,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_FS_ENET=y
 # CONFIG_FS_ENET_HAS_SCC is not set
 CONFIG_FS_ENET_HAS_FCC=y
@@ -567,6 +589,7 @@ CONFIG_FS_ENET_MDIO_FCC=y
 CONFIG_NETDEV_1000=y
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 CONFIG_NETDEV_10000=y
 
 #
@@ -654,6 +677,11 @@ CONFIG_GEN_RTC=y
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -710,22 +738,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -777,6 +790,10 @@ CONFIG_USB_SUPPORT=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -797,10 +814,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -916,6 +935,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -946,6 +966,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -958,7 +981,6 @@ CONFIG_DEBUG_MUTEXES=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -972,16 +994,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -990,9 +1011,13 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_PPC_EMULATED_STATS is not set
 # CONFIG_CODE_PATCHING_SELFTEST is not set
 # CONFIG_FTR_FIXUP_SELFTEST is not set
 # CONFIG_MSI_BITMAP_SELFTEST is not set
diff --git a/arch/powerpc/configs/85xx/mpc8540_ads_defconfig b/arch/powerpc/configs/85xx/mpc8540_ads_defconfig
index 7b43be7586b..fb10cc83702 100644
--- a/arch/powerpc/configs/85xx/mpc8540_ads_defconfig
+++ b/arch/powerpc/configs/85xx/mpc8540_ads_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:17 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:15 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -111,7 +114,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -124,8 +126,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -138,6 +147,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -145,7 +158,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -178,6 +191,7 @@ CONFIG_MPC8540_ADS=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -226,6 +240,7 @@ CONFIG_BINFMT_ELF=y
 CONFIG_BINFMT_MISC=y
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -244,9 +259,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -348,6 +363,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -365,7 +381,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -387,6 +407,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_CONNECTOR is not set
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -423,7 +444,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_MD is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -462,9 +482,11 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_NETDEV_1000=y
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 CONFIG_NETDEV_10000=y
 
 #
@@ -555,6 +577,11 @@ CONFIG_GEN_RTC=y
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -590,22 +617,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -657,6 +669,10 @@ CONFIG_USB_SUPPORT=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -676,10 +692,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -794,6 +812,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -824,6 +843,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -835,7 +857,6 @@ CONFIG_DEBUG_MUTEXES=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -849,16 +870,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -866,6 +886,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/85xx/mpc8560_ads_defconfig b/arch/powerpc/configs/85xx/mpc8560_ads_defconfig
index 62adb71a5d4..5c8ce697882 100644
--- a/arch/powerpc/configs/85xx/mpc8560_ads_defconfig
+++ b/arch/powerpc/configs/85xx/mpc8560_ads_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:17 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:16 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -112,7 +115,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -125,9 +127,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -141,6 +150,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -148,7 +161,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -181,6 +194,7 @@ CONFIG_MPC8560_ADS=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -229,6 +243,7 @@ CONFIG_BINFMT_ELF=y
 CONFIG_BINFMT_MISC=y
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -247,9 +262,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -360,6 +375,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -377,7 +393,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -400,6 +420,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -431,6 +452,7 @@ CONFIG_MISC_DEVICES=y
 # EEPROM support
 #
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -450,14 +472,17 @@ CONFIG_HAVE_IDE=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -504,6 +529,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_FS_ENET=y
 # CONFIG_FS_ENET_HAS_SCC is not set
@@ -527,8 +553,10 @@ CONFIG_E1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -646,6 +674,11 @@ CONFIG_GEN_RTC=y
 CONFIG_DEVPORT=y
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -707,22 +740,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -779,6 +797,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -798,10 +820,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -916,6 +940,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -946,6 +971,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -957,7 +985,6 @@ CONFIG_DEBUG_MUTEXES=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -971,16 +998,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -988,6 +1014,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/85xx/mpc85xx_cds_defconfig b/arch/powerpc/configs/85xx/mpc85xx_cds_defconfig
index 41209e3a654..158e63e8607 100644
--- a/arch/powerpc/configs/85xx/mpc85xx_cds_defconfig
+++ b/arch/powerpc/configs/85xx/mpc85xx_cds_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:18 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:17 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -111,7 +114,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -124,9 +126,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -139,6 +148,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -146,7 +159,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -179,6 +192,7 @@ CONFIG_MPC85xx_CDS=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -227,6 +241,7 @@ CONFIG_BINFMT_ELF=y
 CONFIG_BINFMT_MISC=y
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -245,9 +260,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -358,6 +373,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -375,7 +391,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -397,6 +417,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_CONNECTOR is not set
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -428,6 +449,7 @@ CONFIG_MISC_DEVICES=y
 # EEPROM support
 #
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -502,14 +524,17 @@ CONFIG_BLK_DEV_IDEDMA=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -556,6 +581,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -575,8 +601,10 @@ CONFIG_E1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -698,6 +726,11 @@ CONFIG_GEN_RTC=y
 CONFIG_DEVPORT=y
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -737,22 +770,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -809,6 +827,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -828,10 +850,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -946,6 +970,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -976,6 +1001,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -987,7 +1015,6 @@ CONFIG_DEBUG_MUTEXES=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1001,16 +1028,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1018,6 +1044,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/85xx/sbc8548_defconfig b/arch/powerpc/configs/85xx/sbc8548_defconfig
index 6c36c9c7abf..2726fca1d69 100644
--- a/arch/powerpc/configs/85xx/sbc8548_defconfig
+++ b/arch/powerpc/configs/85xx/sbc8548_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:19 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:18 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -110,7 +113,6 @@ CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -123,8 +125,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -137,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -144,7 +157,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -177,6 +190,7 @@ CONFIG_MPC85xx=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -224,6 +238,7 @@ CONFIG_BINFMT_ELF=y
 CONFIG_BINFMT_MISC=y
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -242,9 +257,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -354,6 +369,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -371,7 +387,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -391,6 +411,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_CONNECTOR is not set
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -422,6 +443,7 @@ CONFIG_MISC_DEVICES=y
 # EEPROM support
 #
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -441,14 +463,17 @@ CONFIG_HAVE_IDE=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -495,6 +520,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -514,8 +540,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -637,6 +665,11 @@ CONFIG_GEN_RTC=y
 CONFIG_DEVPORT=y
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -676,22 +709,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -721,6 +739,10 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -732,10 +754,12 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -838,6 +862,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -861,22 +886,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_PPC_EARLY_DEBUG is not set
diff --git a/arch/powerpc/configs/85xx/sbc8560_defconfig b/arch/powerpc/configs/85xx/sbc8560_defconfig
index 4aaf1a6bdc7..b0c469823b0 100644
--- a/arch/powerpc/configs/85xx/sbc8560_defconfig
+++ b/arch/powerpc/configs/85xx/sbc8560_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:20 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:19 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -111,7 +114,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -124,7 +126,14 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -137,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -144,7 +157,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -177,6 +190,7 @@ CONFIG_MPC85xx=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -224,6 +238,7 @@ CONFIG_BINFMT_ELF=y
 CONFIG_BINFMT_MISC=y
 # CONFIG_MATH_EMULATION is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -242,9 +257,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -346,6 +361,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -363,7 +379,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -385,6 +405,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_CONNECTOR is not set
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -421,7 +442,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_MD is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -460,9 +480,11 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_NETDEV_1000=y
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 CONFIG_NETDEV_10000=y
 
 #
@@ -551,6 +573,11 @@ CONFIG_LEGACY_PTY_COUNT=256
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -586,22 +613,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -690,6 +702,10 @@ CONFIG_RTC_DRV_M48T59=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -701,10 +717,12 @@ CONFIG_RTC_DRV_M48T59=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -819,6 +837,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -848,6 +867,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -859,7 +881,6 @@ CONFIG_DEBUG_MUTEXES=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -873,16 +894,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -890,6 +910,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/85xx/socrates_defconfig b/arch/powerpc/configs/85xx/socrates_defconfig
index 79984589db6..04c85dada84 100644
--- a/arch/powerpc/configs/85xx/socrates_defconfig
+++ b/arch/powerpc/configs/85xx/socrates_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:21 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:19 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -109,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -122,9 +124,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -137,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -149,7 +162,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -182,6 +195,7 @@ CONFIG_MPC85xx=y
 # CONFIG_MPC85xx_DS is not set
 CONFIG_SOCRATES=y
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -229,6 +243,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -247,9 +262,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -357,6 +372,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -373,6 +389,7 @@ CONFIG_CAN_BCM=y
 # CAN Device Drivers
 #
 # CONFIG_CAN_VCAN is not set
+# CONFIG_CAN_DEV is not set
 # CONFIG_CAN_DEBUG_DEVICES is not set
 # CONFIG_IRDA is not set
 # CONFIG_BT is not set
@@ -382,7 +399,11 @@ CONFIG_WIRELESS=y
 # CONFIG_WIRELESS_OLD_REGULATORY is not set
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -499,6 +520,7 @@ CONFIG_MTD_NAND_SOCRATES=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
 CONFIG_OF_SPI=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -535,7 +557,9 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_AT25 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -558,10 +582,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 # CONFIG_CHR_DEV_SG is not set
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -588,14 +608,17 @@ CONFIG_SCSI_WAIT_SCAN=m
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -643,6 +666,8 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -662,8 +687,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -733,6 +760,7 @@ CONFIG_INPUT_TOUCHSCREEN=y
 # CONFIG_TOUCHSCREEN_AD7879_I2C is not set
 # CONFIG_TOUCHSCREEN_AD7879_SPI is not set
 # CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_EETI is not set
 # CONFIG_TOUCHSCREEN_FUJITSU is not set
 # CONFIG_TOUCHSCREEN_GUNZE is not set
 # CONFIG_TOUCHSCREEN_ELO is not set
@@ -746,6 +774,7 @@ CONFIG_INPUT_TOUCHSCREEN=y
 # CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
 # CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
 # CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
 # CONFIG_INPUT_MISC is not set
 
 #
@@ -862,7 +891,6 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
@@ -875,12 +903,18 @@ CONFIG_SPI_MASTER=y
 # SPI Master Controller Drivers
 #
 # CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_MPC8xxx is not set
 
 #
 # SPI Protocol Masters
 #
 # CONFIG_SPI_SPIDEV is not set
 # CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -938,6 +972,7 @@ CONFIG_SENSORS_LM75=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -973,24 +1008,10 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1110,7 +1131,7 @@ CONFIG_USB_HID=y
 # CONFIG_HID_CHERRY is not set
 # CONFIG_HID_CHICONY is not set
 # CONFIG_HID_CYPRESS is not set
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 # CONFIG_HID_EZKEY is not set
 # CONFIG_HID_KYE is not set
 # CONFIG_HID_GYRATION is not set
@@ -1124,10 +1145,11 @@ CONFIG_USB_HID=y
 # CONFIG_HID_SAMSUNG is not set
 # CONFIG_HID_SONY is not set
 # CONFIG_HID_SUNPLUS is not set
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-# CONFIG_THRUSTMASTER_FF is not set
-# CONFIG_ZEROPLUS_FF is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1153,6 +1175,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1162,9 +1185,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
+CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PCI=y
 CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1284,6 +1307,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1318,6 +1342,10 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1337,10 +1365,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1449,7 +1479,46 @@ CONFIG_MSDOS_PARTITION=y
 # CONFIG_KARMA_PARTITION is not set
 # CONFIG_EFI_PARTITION is not set
 # CONFIG_SYSV68_PARTITION is not set
-# CONFIG_NLS is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
 # CONFIG_DLM is not set
 # CONFIG_BINARY_PRINTF is not set
 
@@ -1473,6 +1542,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1498,22 +1568,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_PPC_EARLY_DEBUG is not set
diff --git a/arch/powerpc/configs/85xx/stx_gp3_defconfig b/arch/powerpc/configs/85xx/stx_gp3_defconfig
index bd1bfcddbd0..e7e81d6769f 100644
--- a/arch/powerpc/configs/85xx/stx_gp3_defconfig
+++ b/arch/powerpc/configs/85xx/stx_gp3_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:22 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:20 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -112,7 +115,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -125,9 +127,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -142,6 +151,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -153,7 +166,7 @@ CONFIG_MODULES=y
 CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -186,6 +199,7 @@ CONFIG_MPC85xx=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 CONFIG_STX_GP3=y
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -234,6 +248,7 @@ CONFIG_BINFMT_ELF=y
 CONFIG_BINFMT_MISC=m
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -252,9 +267,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -425,6 +440,7 @@ CONFIG_IP_NF_FILTER=m
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -442,7 +458,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -466,6 +486,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=m
+CONFIG_OF_MDIO=y
 CONFIG_PARPORT=m
 CONFIG_PARPORT_PC=m
 # CONFIG_PARPORT_PC_FIFO is not set
@@ -507,7 +528,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -581,10 +604,6 @@ CONFIG_BLK_DEV_SR=m
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 CONFIG_CHR_DEV_SG=m
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 CONFIG_SCSI_MULTI_LUN=y
 CONFIG_SCSI_CONSTANTS=y
 # CONFIG_SCSI_LOGGING is not set
@@ -602,6 +621,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -610,6 +630,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -631,7 +652,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_INIA100 is not set
 # CONFIG_SCSI_PPA is not set
 # CONFIG_SCSI_IMM is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_QLOGIC_1280 is not set
@@ -654,14 +674,17 @@ CONFIG_SCSI_LOWLEVEL=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -708,6 +731,7 @@ CONFIG_NET_ETHERNET=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_NET_POCKET is not set
 # CONFIG_ATL2 is not set
 # CONFIG_FS_ENET is not set
@@ -729,8 +753,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -802,12 +828,13 @@ CONFIG_INPUT_EVDEV=m
 #
 CONFIG_INPUT_KEYBOARD=y
 CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
 # CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_MATRIX is not set
 # CONFIG_KEYBOARD_NEWTON is not set
 # CONFIG_KEYBOARD_STOWAWAY is not set
-# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
 CONFIG_INPUT_MOUSE=y
 CONFIG_MOUSE_PS2=y
 CONFIG_MOUSE_PS2_ALPS=y
@@ -821,6 +848,7 @@ CONFIG_MOUSE_PS2_TRACKPOINT=y
 # CONFIG_MOUSE_BCM5974 is not set
 # CONFIG_MOUSE_VSXXXAA is not set
 # CONFIG_MOUSE_GPIO is not set
+# CONFIG_MOUSE_SYNAPTICS_I2C is not set
 # CONFIG_INPUT_JOYSTICK is not set
 # CONFIG_INPUT_TABLET is not set
 # CONFIG_INPUT_TOUCHSCREEN is not set
@@ -911,6 +939,7 @@ CONFIG_I2C_ALGOBIT=m
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
 # CONFIG_I2C_CPM is not set
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_GPIO is not set
 # CONFIG_I2C_MPC is not set
 # CONFIG_I2C_OCORES is not set
@@ -941,13 +970,17 @@ CONFIG_I2C_ALGOBIT=m
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -1027,6 +1060,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1060,23 +1094,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1143,6 +1163,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1162,10 +1186,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1316,6 +1342,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1346,6 +1373,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1358,7 +1388,6 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1372,16 +1401,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1389,6 +1417,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/85xx/tqm8540_defconfig b/arch/powerpc/configs/85xx/tqm8540_defconfig
index 767600145fb..2c407523aad 100644
--- a/arch/powerpc/configs/85xx/tqm8540_defconfig
+++ b/arch/powerpc/configs/85xx/tqm8540_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:23 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:21 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -109,7 +112,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -122,9 +124,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -137,6 +146,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -144,7 +157,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -177,6 +190,7 @@ CONFIG_MPC85xx=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 CONFIG_TQM8540=y
 # CONFIG_TQM8541 is not set
@@ -225,6 +239,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -243,9 +258,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -353,6 +368,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -370,7 +386,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -471,6 +491,7 @@ CONFIG_MTD_CFI_UTIL=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -505,7 +526,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -580,14 +603,17 @@ CONFIG_BLK_DEV_IDEDMA=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -650,6 +676,7 @@ CONFIG_E100=y
 # CONFIG_SMSC9420 is not set
 # CONFIG_SUNDANCE is not set
 # CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
 # CONFIG_VIA_RHINE is not set
 # CONFIG_SC92031 is not set
 # CONFIG_ATL2 is not set
@@ -671,8 +698,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -850,13 +879,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -911,6 +944,7 @@ CONFIG_SENSORS_LM75=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -945,23 +979,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1018,6 +1038,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1037,10 +1061,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1167,6 +1193,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1192,22 +1219,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_PPC_EARLY_DEBUG is not set
diff --git a/arch/powerpc/configs/85xx/tqm8541_defconfig b/arch/powerpc/configs/85xx/tqm8541_defconfig
index 52fafc006dd..845731dc51c 100644
--- a/arch/powerpc/configs/85xx/tqm8541_defconfig
+++ b/arch/powerpc/configs/85xx/tqm8541_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:23 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:22 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -110,7 +113,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -123,9 +125,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -139,6 +148,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -146,7 +159,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -179,6 +192,7 @@ CONFIG_MPC85xx=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 CONFIG_TQM8541=y
@@ -228,6 +242,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -246,9 +261,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -356,6 +371,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -373,7 +389,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -475,6 +495,7 @@ CONFIG_MTD_CFI_UTIL=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -509,7 +530,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -584,14 +607,17 @@ CONFIG_BLK_DEV_IDEDMA=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -654,6 +680,7 @@ CONFIG_E100=y
 # CONFIG_SMSC9420 is not set
 # CONFIG_SUNDANCE is not set
 # CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
 # CONFIG_VIA_RHINE is not set
 # CONFIG_SC92031 is not set
 # CONFIG_ATL2 is not set
@@ -676,8 +703,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -831,6 +860,7 @@ CONFIG_I2C_HELPER_AUTO=y
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
 # CONFIG_I2C_CPM is not set
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_GPIO is not set
 CONFIG_I2C_MPC=y
 # CONFIG_I2C_OCORES is not set
@@ -859,13 +889,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -944,6 +978,7 @@ CONFIG_SENSORS_LM75=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -979,23 +1014,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1052,6 +1073,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1071,10 +1096,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1201,6 +1228,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1226,22 +1254,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_PPC_EARLY_DEBUG is not set
diff --git a/arch/powerpc/configs/85xx/tqm8548_defconfig b/arch/powerpc/configs/85xx/tqm8548_defconfig
index 8b4faae7a9a..4f228a90527 100644
--- a/arch/powerpc/configs/85xx/tqm8548_defconfig
+++ b/arch/powerpc/configs/85xx/tqm8548_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:24 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:23 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -56,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -111,7 +114,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -124,9 +126,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -140,6 +149,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -152,7 +165,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -185,6 +198,7 @@ CONFIG_MPC85xx=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -234,6 +248,7 @@ CONFIG_BINFMT_ELF=y
 CONFIG_BINFMT_MISC=y
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -252,9 +267,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -281,6 +296,8 @@ CONFIG_PCI_DOMAINS=y
 CONFIG_PCI_SYSCALL=y
 CONFIG_PCIEPORTBUS=y
 CONFIG_PCIEAER=y
+# CONFIG_PCIE_ECRC is not set
+# CONFIG_PCIEAER_INJECT is not set
 # CONFIG_PCIEASPM is not set
 CONFIG_ARCH_SUPPORTS_MSI=y
 # CONFIG_PCI_MSI is not set
@@ -368,6 +385,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -497,6 +515,7 @@ CONFIG_MTD_NAND_FSL_UPM=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -531,7 +550,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -551,14 +572,17 @@ CONFIG_HAVE_IDE=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -605,6 +629,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -624,8 +649,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -801,13 +828,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -862,6 +893,7 @@ CONFIG_SENSORS_LM75=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -896,23 +928,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -977,6 +995,7 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1004,6 +1023,10 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1015,10 +1038,12 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1145,6 +1170,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1175,6 +1201,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1187,7 +1216,6 @@ CONFIG_DEBUG_MUTEXES=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1201,16 +1229,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1218,6 +1245,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/85xx/tqm8555_defconfig b/arch/powerpc/configs/85xx/tqm8555_defconfig
index 170360934ce..9196724bebc 100644
--- a/arch/powerpc/configs/85xx/tqm8555_defconfig
+++ b/arch/powerpc/configs/85xx/tqm8555_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:25 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:24 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -110,7 +113,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -123,9 +125,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -139,6 +148,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -146,7 +159,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -179,6 +192,7 @@ CONFIG_MPC85xx=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -228,6 +242,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -246,9 +261,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -356,6 +371,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -373,7 +389,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -475,6 +495,7 @@ CONFIG_MTD_CFI_UTIL=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -509,7 +530,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -584,14 +607,17 @@ CONFIG_BLK_DEV_IDEDMA=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -654,6 +680,7 @@ CONFIG_E100=y
 # CONFIG_SMSC9420 is not set
 # CONFIG_SUNDANCE is not set
 # CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
 # CONFIG_VIA_RHINE is not set
 # CONFIG_SC92031 is not set
 # CONFIG_ATL2 is not set
@@ -676,8 +703,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -831,6 +860,7 @@ CONFIG_I2C_HELPER_AUTO=y
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
 # CONFIG_I2C_CPM is not set
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_GPIO is not set
 CONFIG_I2C_MPC=y
 # CONFIG_I2C_OCORES is not set
@@ -859,13 +889,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -944,6 +978,7 @@ CONFIG_SENSORS_LM75=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -979,23 +1014,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1052,6 +1073,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1071,10 +1096,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1201,6 +1228,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1226,22 +1254,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_PPC_EARLY_DEBUG is not set
diff --git a/arch/powerpc/configs/85xx/tqm8560_defconfig b/arch/powerpc/configs/85xx/tqm8560_defconfig
index f41cc2444d4..2e49a6e9faf 100644
--- a/arch/powerpc/configs/85xx/tqm8560_defconfig
+++ b/arch/powerpc/configs/85xx/tqm8560_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:26 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:25 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -110,7 +113,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -123,9 +125,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -139,6 +148,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -146,7 +159,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -179,6 +192,7 @@ CONFIG_MPC85xx=y
 # CONFIG_MPC85xx_DS is not set
 # CONFIG_SOCRATES is not set
 # CONFIG_KSI8560 is not set
+# CONFIG_XES_MPC85xx is not set
 # CONFIG_STX_GP3 is not set
 # CONFIG_TQM8540 is not set
 # CONFIG_TQM8541 is not set
@@ -228,6 +242,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -246,9 +261,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -356,6 +371,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -373,7 +389,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -475,6 +495,7 @@ CONFIG_MTD_CFI_UTIL=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -509,7 +530,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -584,14 +607,17 @@ CONFIG_BLK_DEV_IDEDMA=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -654,6 +680,7 @@ CONFIG_E100=y
 # CONFIG_SMSC9420 is not set
 # CONFIG_SUNDANCE is not set
 # CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
 # CONFIG_VIA_RHINE is not set
 # CONFIG_SC92031 is not set
 # CONFIG_ATL2 is not set
@@ -676,8 +703,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -831,6 +860,7 @@ CONFIG_I2C_HELPER_AUTO=y
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
 # CONFIG_I2C_CPM is not set
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_GPIO is not set
 CONFIG_I2C_MPC=y
 # CONFIG_I2C_OCORES is not set
@@ -859,13 +889,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -944,6 +978,7 @@ CONFIG_SENSORS_LM75=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -979,23 +1014,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1052,6 +1073,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1071,10 +1096,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1201,6 +1228,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1226,22 +1254,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_PPC_EARLY_DEBUG is not set
diff --git a/arch/powerpc/configs/85xx/xes_mpc85xx_defconfig b/arch/powerpc/configs/85xx/xes_mpc85xx_defconfig
index 2552cbefba6..1025da2bf06 100644
--- a/arch/powerpc/configs/85xx/xes_mpc85xx_defconfig
+++ b/arch/powerpc/configs/85xx/xes_mpc85xx_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc6
-# Thu Jun 11 11:25:17 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:25 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -35,15 +35,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -64,6 +65,7 @@ CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -114,7 +116,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -127,9 +128,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -144,6 +152,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_USE_GENERIC_SMP_HELPERS=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -157,7 +169,7 @@ CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
-CONFIG_LBD=y
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -239,6 +251,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -258,9 +271,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -287,6 +300,8 @@ CONFIG_PCI_DOMAINS=y
 CONFIG_PCI_SYSCALL=y
 CONFIG_PCIEPORTBUS=y
 CONFIG_PCIEAER=y
+# CONFIG_PCIE_ECRC is not set
+# CONFIG_PCIEAER_INJECT is not set
 # CONFIG_PCIEASPM is not set
 CONFIG_ARCH_SUPPORTS_MSI=y
 CONFIG_PCI_MSI=y
@@ -404,6 +419,7 @@ CONFIG_IPV6_NDISC_NODETYPE=y
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -540,6 +556,7 @@ CONFIG_MTD_NAND_FSL_UPM=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -575,7 +592,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -599,10 +618,6 @@ CONFIG_BLK_DEV_SR=y
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 CONFIG_SCSI_MULTI_LUN=y
 # CONFIG_SCSI_CONSTANTS is not set
 CONFIG_SCSI_LOGGING=y
@@ -619,6 +634,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 # CONFIG_SCSI_SRP_ATTRS is not set
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -627,6 +643,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -646,7 +663,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -730,14 +746,17 @@ CONFIG_PATA_ALI=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=y
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -784,6 +803,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -803,8 +823,10 @@ CONFIG_E1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -986,13 +1008,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_DS1682 is not set
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -1072,6 +1098,7 @@ CONFIG_SENSORS_LM90=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1126,23 +1153,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1187,7 +1200,7 @@ CONFIG_USB_HID=y
 # CONFIG_HID_CHERRY is not set
 # CONFIG_HID_CHICONY is not set
 # CONFIG_HID_CYPRESS is not set
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 # CONFIG_HID_EZKEY is not set
 # CONFIG_HID_KYE is not set
 # CONFIG_HID_GYRATION is not set
@@ -1201,10 +1214,11 @@ CONFIG_USB_HID=y
 # CONFIG_HID_SAMSUNG is not set
 # CONFIG_HID_SONY is not set
 # CONFIG_HID_SUNPLUS is not set
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-# CONFIG_THRUSTMASTER_FF is not set
-# CONFIG_ZEROPLUS_FF is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1230,6 +1244,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 # CONFIG_USB_EHCI_HCD is not set
 # CONFIG_USB_OXU210HP_HCD is not set
 # CONFIG_USB_ISP116X_HCD is not set
@@ -1325,7 +1340,7 @@ CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_GPIO_PLATFORM=y
 CONFIG_LEDS_GPIO_OF=y
-# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_LP3944 is not set
 CONFIG_LEDS_PCA955X=y
 # CONFIG_LEDS_BD2802 is not set
 
@@ -1352,8 +1367,6 @@ CONFIG_EDAC=y
 # CONFIG_EDAC_DEBUG is not set
 CONFIG_EDAC_MM_EDAC=y
 CONFIG_EDAC_MPC85XX=y
-# CONFIG_EDAC_AMD8131 is not set
-# CONFIG_EDAC_AMD8111 is not set
 CONFIG_RTC_LIB=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_HCTOSYS=y
@@ -1385,6 +1398,7 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1425,6 +1439,10 @@ CONFIG_NET_DMA=y
 # CONFIG_DMATEST is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1444,11 +1462,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1629,6 +1648,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1659,6 +1679,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1671,7 +1694,6 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1685,16 +1707,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1702,6 +1723,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/86xx/gef_ppc9a_defconfig b/arch/powerpc/configs/86xx/gef_ppc9a_defconfig
index d8354d993b2..527ad1a5e80 100644
--- a/arch/powerpc/configs/86xx/gef_ppc9a_defconfig
+++ b/arch/powerpc/configs/86xx/gef_ppc9a_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jul  2 13:55:24 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:31 2009
 #
 # CONFIG_PPC64 is not set
 
@@ -39,6 +39,7 @@ CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_GENERIC_LOCKBREAK=y
@@ -1322,6 +1323,8 @@ CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
 # CONFIG_USB_OHCI_HCD_PPC_OF is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
diff --git a/arch/powerpc/configs/86xx/gef_sbc310_defconfig b/arch/powerpc/configs/86xx/gef_sbc310_defconfig
index f2362e5bf06..cd338d493be 100644
--- a/arch/powerpc/configs/86xx/gef_sbc310_defconfig
+++ b/arch/powerpc/configs/86xx/gef_sbc310_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jul  2 14:10:12 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:29 2009
 #
 # CONFIG_PPC64 is not set
 
@@ -39,6 +39,7 @@ CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_GENERIC_LOCKBREAK=y
@@ -1267,6 +1268,8 @@ CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
 # CONFIG_USB_OHCI_HCD_PPC_OF is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
diff --git a/arch/powerpc/configs/86xx/gef_sbc610_defconfig b/arch/powerpc/configs/86xx/gef_sbc610_defconfig
index c6a7fc82b69..ba47883f4aa 100644
--- a/arch/powerpc/configs/86xx/gef_sbc610_defconfig
+++ b/arch/powerpc/configs/86xx/gef_sbc610_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:30 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:30 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_PHYS_64BIT is not set
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_PPC32=y
@@ -32,16 +34,17 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_GENERIC_LOCKBREAK=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -56,11 +59,13 @@ CONFIG_PPC_UDBG_16550=y
 CONFIG_GENERIC_TBSYNC=y
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -114,7 +119,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -127,8 +131,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -143,6 +154,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_USE_GENERIC_SMP_HELPERS=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -156,7 +171,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -235,6 +250,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=m
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -256,9 +272,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -285,6 +301,8 @@ CONFIG_PCI_DOMAINS=y
 CONFIG_PCI_SYSCALL=y
 CONFIG_PCIEPORTBUS=y
 CONFIG_PCIEAER=y
+# CONFIG_PCIE_ECRC is not set
+# CONFIG_PCIEAER_INJECT is not set
 # CONFIG_PCIEASPM is not set
 CONFIG_ARCH_SUPPORTS_MSI=y
 # CONFIG_PCI_MSI is not set
@@ -510,6 +528,7 @@ CONFIG_LLC=m
 # CONFIG_ECONET is not set
 CONFIG_WAN_ROUTER=m
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 CONFIG_NET_SCHED=y
 
 #
@@ -566,7 +585,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -678,6 +701,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -713,7 +737,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -737,10 +763,6 @@ CONFIG_BLK_DEV_SR=y
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 # CONFIG_CHR_DEV_SG is not set
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -757,6 +779,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 # CONFIG_SCSI_SRP_ATTRS is not set
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -765,6 +788,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -784,7 +808,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -868,14 +891,17 @@ CONFIG_SATA_SIL=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=m
 CONFIG_BONDING=m
 # CONFIG_MACVLAN is not set
@@ -922,6 +948,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -941,8 +968,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -1149,13 +1178,17 @@ CONFIG_DS1682=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -1235,6 +1268,7 @@ CONFIG_SENSORS_LM92=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1290,24 +1324,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1352,7 +1371,7 @@ CONFIG_HID_BELKIN=y
 CONFIG_HID_CHERRY=y
 CONFIG_HID_CHICONY=y
 CONFIG_HID_CYPRESS=y
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 CONFIG_HID_EZKEY=y
 # CONFIG_HID_KYE is not set
 CONFIG_HID_GYRATION=y
@@ -1369,10 +1388,11 @@ CONFIG_HID_PETALYNX=y
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-CONFIG_THRUSTMASTER_FF=m
-CONFIG_ZEROPLUS_FF=m
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1398,6 +1418,7 @@ CONFIG_USB=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1407,6 +1428,8 @@ CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
 # CONFIG_USB_OHCI_HCD_PPC_OF is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
@@ -1527,6 +1550,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 CONFIG_RTC_DRV_RX8581=y
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1554,6 +1578,10 @@ CONFIG_RTC_DRV_RX8581=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1575,10 +1603,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1645,6 +1675,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1734,6 +1765,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1759,10 +1791,14 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_TIMER_STATS is not set
 # CONFIG_DEBUG_OBJECTS is not set
 # CONFIG_DEBUG_SLAB is not set
+CONFIG_DEBUG_PREEMPT=y
 # CONFIG_DEBUG_RT_MUTEXES is not set
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1774,7 +1810,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1788,17 +1823,16 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_PREEMPT_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1806,6 +1840,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
@@ -1829,7 +1866,6 @@ CONFIG_SECURITY_NETWORK=y
 # CONFIG_SECURITY_PATH is not set
 # CONFIG_SECURITY_FILE_CAPABILITIES is not set
 # CONFIG_SECURITY_ROOTPLUG is not set
-CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0
 # CONFIG_SECURITY_TOMOYO is not set
 CONFIG_CRYPTO=y
 
diff --git a/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig b/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig
index cfd2efcc6bc..a61f183f718 100644
--- a/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig
+++ b/arch/powerpc/configs/86xx/mpc8610_hpcd_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:28 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:27 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_PHYS_64BIT is not set
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -53,11 +56,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -109,7 +114,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -122,9 +126,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -138,6 +149,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -150,7 +165,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -230,6 +245,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -250,9 +266,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -279,6 +295,8 @@ CONFIG_PCI_DOMAINS=y
 CONFIG_PCI_SYSCALL=y
 CONFIG_PCIEPORTBUS=y
 CONFIG_PCIEAER=y
+# CONFIG_PCIE_ECRC is not set
+# CONFIG_PCIEAER_INJECT is not set
 # CONFIG_PCIEASPM is not set
 CONFIG_ARCH_SUPPORTS_MSI=y
 # CONFIG_PCI_MSI is not set
@@ -381,6 +399,7 @@ CONFIG_IPV6_NDISC_NODETYPE=y
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -398,7 +417,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -549,7 +572,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -620,10 +645,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -640,6 +661,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 # CONFIG_SCSI_SRP_ATTRS is not set
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -648,6 +670,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -667,7 +690,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -751,14 +773,17 @@ CONFIG_PATA_ALI=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=y
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -792,6 +817,7 @@ CONFIG_ULI526X=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 # CONFIG_NETDEV_1000 is not set
 # CONFIG_NETDEV_10000 is not set
@@ -959,13 +985,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -993,23 +1023,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1106,6 +1122,11 @@ CONFIG_SND_PCM_OSS_PLUGINS=y
 CONFIG_SND_VERBOSE_PROCFS=y
 # CONFIG_SND_VERBOSE_PRINTK is not set
 # CONFIG_SND_DEBUG is not set
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
 CONFIG_SND_DRIVERS=y
 # CONFIG_SND_DUMMY is not set
 # CONFIG_SND_MTPAV is not set
@@ -1130,6 +1151,7 @@ CONFIG_SND_PCI=y
 # CONFIG_SND_CS4281 is not set
 # CONFIG_SND_CS46XX is not set
 # CONFIG_SND_CS5530 is not set
+# CONFIG_SND_CTXFI is not set
 # CONFIG_SND_DARLA20 is not set
 # CONFIG_SND_GINA20 is not set
 # CONFIG_SND_LAYLA20 is not set
@@ -1160,6 +1182,7 @@ CONFIG_SND_PCI=y
 # CONFIG_SND_INTEL8X0 is not set
 # CONFIG_SND_INTEL8X0M is not set
 # CONFIG_SND_KORG1212 is not set
+# CONFIG_SND_LX6464ES is not set
 # CONFIG_SND_MAESTRO3 is not set
 # CONFIG_SND_MIXART is not set
 # CONFIG_SND_NM256 is not set
@@ -1251,6 +1274,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1278,6 +1302,10 @@ CONFIG_RTC_DRV_CMOS=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1297,12 +1325,15 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 # CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
 # CONFIG_QUOTA is not set
 # CONFIG_AUTOFS_FS is not set
 # CONFIG_AUTOFS4_FS is not set
@@ -1464,6 +1495,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1494,6 +1526,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1506,7 +1541,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1520,16 +1554,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1537,6 +1570,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig b/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig
index 0bee3e30394..7016ce73260 100644
--- a/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig
+++ b/arch/powerpc/configs/86xx/mpc8641_hpcn_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:28 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:28 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_PHYS_64BIT is not set
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_PPC32=y
@@ -32,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -54,11 +57,13 @@ CONFIG_PPC_UDBG_16550=y
 CONFIG_GENERIC_TBSYNC=y
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -113,7 +118,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -126,9 +130,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -143,6 +154,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_USE_GENERIC_SMP_HELPERS=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -156,7 +171,7 @@ CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
-CONFIG_LBD=y
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -234,7 +249,9 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=m
-# CONFIG_IOMMU_HELPER is not set
+CONFIG_IOMMU_HELPER=y
+CONFIG_SWIOTLB=y
+CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -256,9 +273,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -401,6 +418,7 @@ CONFIG_SCTP_HMAC_MD5=y
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -419,7 +437,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -444,6 +466,7 @@ CONFIG_EXTRA_FIRMWARE=""
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -479,7 +502,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 CONFIG_EEPROM_LEGACY=y
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -503,10 +528,6 @@ CONFIG_BLK_DEV_SR=y
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 CONFIG_SCSI_MULTI_LUN=y
 # CONFIG_SCSI_CONSTANTS is not set
 CONFIG_SCSI_LOGGING=y
@@ -524,6 +545,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -532,6 +554,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -551,7 +574,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -635,14 +657,17 @@ CONFIG_PATA_ALI=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=y
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -689,6 +714,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -708,8 +734,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -909,13 +937,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -943,76 +975,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-CONFIG_DVB_CORE=m
-CONFIG_VIDEO_MEDIA=m
-
-#
-# Multimedia drivers
-#
-# CONFIG_MEDIA_ATTACH is not set
-CONFIG_MEDIA_TUNER=m
-# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
-CONFIG_MEDIA_TUNER_SIMPLE=m
-CONFIG_MEDIA_TUNER_TDA8290=m
-CONFIG_MEDIA_TUNER_TDA9887=m
-CONFIG_MEDIA_TUNER_TEA5761=m
-CONFIG_MEDIA_TUNER_TEA5767=m
-CONFIG_MEDIA_TUNER_MT20XX=m
-CONFIG_MEDIA_TUNER_XC2028=m
-CONFIG_MEDIA_TUNER_XC5000=m
-CONFIG_MEDIA_TUNER_MC44S803=m
-# CONFIG_DVB_DYNAMIC_MINORS is not set
-CONFIG_DVB_CAPTURE_DRIVERS=y
-
-#
-# Supported SAA7146 based PCI Adapters
-#
-# CONFIG_TTPCI_EEPROM is not set
-# CONFIG_DVB_BUDGET_CORE is not set
-
-#
-# Supported USB Adapters
-#
-# CONFIG_DVB_USB is not set
-# CONFIG_DVB_TTUSB_BUDGET is not set
-# CONFIG_DVB_TTUSB_DEC is not set
-# CONFIG_DVB_SIANO_SMS1XXX is not set
-
-#
-# Supported FlexCopII (B2C2) Adapters
-#
-# CONFIG_DVB_B2C2_FLEXCOP is not set
-
-#
-# Supported BT878 Adapters
-#
-
-#
-# Supported Pluto2 Adapters
-#
-# CONFIG_DVB_PLUTO2 is not set
-
-#
-# Supported SDMC DM1105 Adapters
-#
-# CONFIG_DVB_DM1105 is not set
-
-#
-# Supported DVB Frontends
-#
-# CONFIG_DVB_FE_CUSTOMISE is not set
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1052,6 +1017,11 @@ CONFIG_SND_VERBOSE_PROCFS=y
 # CONFIG_SND_VERBOSE_PRINTK is not set
 # CONFIG_SND_DEBUG is not set
 CONFIG_SND_VMASTER=y
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
 CONFIG_SND_AC97_CODEC=y
 CONFIG_SND_DRIVERS=y
 # CONFIG_SND_DUMMY is not set
@@ -1078,6 +1048,7 @@ CONFIG_SND_PCI=y
 # CONFIG_SND_CS4281 is not set
 # CONFIG_SND_CS46XX is not set
 # CONFIG_SND_CS5530 is not set
+# CONFIG_SND_CTXFI is not set
 # CONFIG_SND_DARLA20 is not set
 # CONFIG_SND_GINA20 is not set
 # CONFIG_SND_LAYLA20 is not set
@@ -1108,6 +1079,7 @@ CONFIG_SND_PCI=y
 CONFIG_SND_INTEL8X0=y
 # CONFIG_SND_INTEL8X0M is not set
 # CONFIG_SND_KORG1212 is not set
+# CONFIG_SND_LX6464ES is not set
 # CONFIG_SND_MAESTRO3 is not set
 # CONFIG_SND_MIXART is not set
 # CONFIG_SND_NM256 is not set
@@ -1152,7 +1124,7 @@ CONFIG_HID_BELKIN=y
 CONFIG_HID_CHERRY=y
 CONFIG_HID_CHICONY=y
 CONFIG_HID_CYPRESS=y
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 CONFIG_HID_EZKEY=y
 # CONFIG_HID_KYE is not set
 CONFIG_HID_GYRATION=y
@@ -1169,10 +1141,11 @@ CONFIG_HID_PETALYNX=y
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-CONFIG_THRUSTMASTER_FF=m
-CONFIG_ZEROPLUS_FF=m
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1198,6 +1171,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1207,9 +1181,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 CONFIG_USB_OHCI_HCD_PPC_OF_LE=y
+CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PCI=y
 CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1329,6 +1303,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1356,6 +1331,10 @@ CONFIG_RTC_DRV_CMOS=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1375,11 +1354,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1454,6 +1434,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
 # CONFIG_NFSD_V3 is not set
@@ -1555,6 +1536,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1585,6 +1567,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1597,7 +1582,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1611,16 +1595,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1628,6 +1611,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/86xx/sbc8641d_defconfig b/arch/powerpc/configs/86xx/sbc8641d_defconfig
index c30a0c71587..f5ca2e0cd40 100644
--- a/arch/powerpc/configs/86xx/sbc8641d_defconfig
+++ b/arch/powerpc/configs/86xx/sbc8641d_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:27 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:26 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_PHYS_64BIT is not set
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_PPC32=y
@@ -32,16 +34,17 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_GENERIC_LOCKBREAK=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -55,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 CONFIG_GENERIC_TBSYNC=y
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -113,7 +118,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -126,8 +130,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -142,6 +153,11 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_USE_GENERIC_SMP_HELPERS=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -155,7 +171,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -234,6 +250,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=m
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -255,9 +272,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -284,6 +301,8 @@ CONFIG_PCI_DOMAINS=y
 CONFIG_PCI_SYSCALL=y
 CONFIG_PCIEPORTBUS=y
 CONFIG_PCIEAER=y
+# CONFIG_PCIE_ECRC is not set
+# CONFIG_PCIEAER_INJECT is not set
 # CONFIG_PCIEASPM is not set
 CONFIG_ARCH_SUPPORTS_MSI=y
 # CONFIG_PCI_MSI is not set
@@ -508,6 +527,7 @@ CONFIG_LLC=m
 # CONFIG_ECONET is not set
 CONFIG_WAN_ROUTER=m
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 CONFIG_NET_SCHED=y
 
 #
@@ -564,7 +584,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -675,6 +699,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -709,7 +734,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -736,6 +763,7 @@ CONFIG_BLK_DEV_DM=y
 CONFIG_DM_CRYPT=y
 CONFIG_DM_SNAPSHOT=y
 CONFIG_DM_MIRROR=y
+# CONFIG_DM_LOG_USERSPACE is not set
 CONFIG_DM_ZERO=y
 # CONFIG_DM_MULTIPATH is not set
 # CONFIG_DM_DELAY is not set
@@ -747,14 +775,17 @@ CONFIG_DM_ZERO=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=m
 CONFIG_BONDING=m
 # CONFIG_MACVLAN is not set
@@ -801,6 +832,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -820,8 +852,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -1018,13 +1052,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -1079,6 +1117,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1127,23 +1166,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1207,6 +1232,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1236,8 +1265,8 @@ CONFIG_REISERFS_FS_POSIX_ACL=y
 # CONFIG_REISERFS_FS_SECURITY is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 CONFIG_OCFS2_FS=m
 CONFIG_OCFS2_FS_O2CB=m
 CONFIG_OCFS2_FS_STATS=y
@@ -1245,6 +1274,8 @@ CONFIG_OCFS2_DEBUG_MASKLOG=y
 # CONFIG_OCFS2_DEBUG_FS is not set
 # CONFIG_OCFS2_FS_POSIX_ACL is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1318,6 +1349,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1409,6 +1441,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1434,10 +1467,14 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_TIMER_STATS is not set
 # CONFIG_DEBUG_OBJECTS is not set
 # CONFIG_DEBUG_SLAB is not set
+CONFIG_DEBUG_PREEMPT=y
 # CONFIG_DEBUG_RT_MUTEXES is not set
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1449,7 +1486,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1463,17 +1499,16 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_PREEMPT_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1482,9 +1517,13 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_PPC_EMULATED_STATS is not set
 # CONFIG_CODE_PATCHING_SELFTEST is not set
 # CONFIG_FTR_FIXUP_SELFTEST is not set
 # CONFIG_MSI_BITMAP_SELFTEST is not set
@@ -1505,7 +1544,6 @@ CONFIG_SECURITY_NETWORK=y
 # CONFIG_SECURITY_NETWORK_XFRM is not set
 # CONFIG_SECURITY_PATH is not set
 # CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0
 # CONFIG_SECURITY_TOMOYO is not set
 CONFIG_CRYPTO=y
 
diff --git a/arch/powerpc/configs/adder875_defconfig b/arch/powerpc/configs/adder875_defconfig
index 74f7f7c6fdc..aece6bb5f73 100644
--- a/arch/powerpc/configs/adder875_defconfig
+++ b/arch/powerpc/configs/adder875_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:21:50 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:47 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 # CONFIG_PPC_85xx is not set
 CONFIG_PPC_8xx=y
 # CONFIG_40x is not set
@@ -27,15 +27,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -49,12 +50,14 @@ CONFIG_OF=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 CONFIG_REDBOOT=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -101,7 +104,6 @@ CONFIG_EMBEDDED=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -114,8 +116,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 # CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -129,13 +138,18 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
 CONFIG_BASE_SMALL=1
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -220,6 +234,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_MATH_EMULATION is not set
 # CONFIG_8XX_MINIMAL_FPEMU is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
@@ -239,9 +254,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -280,6 +295,7 @@ CONFIG_PAGE_OFFSET=0xc0000000
 CONFIG_KERNEL_START=0xc0000000
 CONFIG_PHYSICAL_START=0x00000000
 CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_SIZE=0x00200000
 CONFIG_NET=y
 
 #
@@ -336,6 +352,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -353,7 +370,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -452,6 +473,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 #
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 # CONFIG_BLK_DEV is not set
 # CONFIG_MISC_DEVICES is not set
@@ -469,7 +491,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_MD is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -508,6 +529,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_FS_ENET=y
 # CONFIG_FS_ENET_HAS_SCC is not set
 CONFIG_FS_ENET_HAS_FEC=y
@@ -556,11 +578,11 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
 #
 CONFIG_INPUT_KEYBOARD=y
 CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
 # CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
 # CONFIG_KEYBOARD_NEWTON is not set
 # CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
 CONFIG_INPUT_MOUSE=y
 CONFIG_MOUSE_PS2=y
 CONFIG_MOUSE_PS2_ALPS=y
@@ -622,6 +644,11 @@ CONFIG_GEN_RTC=y
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -644,22 +671,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -685,6 +697,10 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -696,12 +712,15 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 # CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
 # CONFIG_QUOTA is not set
 # CONFIG_AUTOFS_FS is not set
 # CONFIG_AUTOFS4_FS is not set
@@ -818,6 +837,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -846,6 +866,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_SLUB_STATS is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -857,7 +880,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -870,16 +892,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -888,9 +909,13 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_PPC_EMULATED_STATS is not set
 # CONFIG_CODE_PATCHING_SELFTEST is not set
 # CONFIG_FTR_FIXUP_SELFTEST is not set
 # CONFIG_MSI_BITMAP_SELFTEST is not set
diff --git a/arch/powerpc/configs/c2k_defconfig b/arch/powerpc/configs/c2k_defconfig
index 9ffa8de9280..8105360d53f 100644
--- a/arch/powerpc/configs/c2k_defconfig
+++ b/arch/powerpc/configs/c2k_defconfig
@@ -1,25 +1,27 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:21:51 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:48 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_NOT_COHERENT_CACHE=y
 CONFIG_CHECK_CACHE_COHERENCY=y
@@ -32,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -54,11 +57,13 @@ CONFIG_OF=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -118,7 +123,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -131,16 +135,23 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
 # CONFIG_SLOB is not set
 CONFIG_PROFILING=y
 CONFIG_TRACEPOINTS=y
-# CONFIG_MARKERS is not set
+CONFIG_MARKERS=y
 CONFIG_OPROFILE=m
 CONFIG_HAVE_OPROFILE=y
 CONFIG_KPROBES=y
@@ -150,6 +161,11 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -162,7 +178,7 @@ CONFIG_MODULE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-CONFIG_LBD=y
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -258,6 +274,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
@@ -279,9 +296,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -331,6 +348,7 @@ CONFIG_PAGE_OFFSET=0xc0000000
 CONFIG_KERNEL_START=0xc0000000
 CONFIG_PHYSICAL_START=0x00000000
 CONFIG_TASK_SIZE=0xc0000000
+CONFIG_CONSISTENT_SIZE=0x00200000
 CONFIG_NET=y
 
 #
@@ -583,6 +601,7 @@ CONFIG_LLC=m
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 CONFIG_NET_SCHED=y
 
 #
@@ -663,7 +682,11 @@ CONFIG_WIRELESS_OLD_REGULATORY=y
 CONFIG_WIRELESS_EXT=y
 CONFIG_WIRELESS_EXT_SYSFS=y
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -772,6 +795,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=m
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -816,10 +840,6 @@ CONFIG_BLK_DEV_SR=m
 CONFIG_BLK_DEV_SR_VENDOR=y
 CONFIG_CHR_DEV_SG=m
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 CONFIG_SCSI_CONSTANTS=y
 CONFIG_SCSI_LOGGING=y
@@ -836,6 +856,7 @@ CONFIG_SCSI_ISCSI_ATTRS=m
 CONFIG_SCSI_SRP_ATTRS=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 CONFIG_BLK_DEV_3W_XXXX_RAID=m
 CONFIG_SCSI_3W_9XXX=m
 CONFIG_SCSI_ACARD=m
@@ -854,6 +875,7 @@ CONFIG_AIC79XX_RESET_DELAY_MS=15000
 CONFIG_AIC79XX_DEBUG_MASK=0
 # CONFIG_AIC79XX_REG_PRETTY_PRINT is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 CONFIG_SCSI_ARCMSR=m
@@ -875,7 +897,6 @@ CONFIG_SCSI_GDTH=m
 CONFIG_SCSI_IPS=m
 CONFIG_SCSI_INITIO=m
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 CONFIG_SCSI_SYM53C8XX_2=m
 CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
@@ -903,14 +924,17 @@ CONFIG_SCSI_LPFC=m
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=m
 CONFIG_BONDING=m
 # CONFIG_MACVLAN is not set
@@ -957,6 +981,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -976,6 +1001,7 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_MV643XX_ETH=y
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
@@ -1177,13 +1203,17 @@ CONFIG_I2C_MV64XXX=m
 CONFIG_SENSORS_PCF8574=m
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -1238,6 +1268,7 @@ CONFIG_SENSORS_SMSC47M1=m
 CONFIG_SENSORS_SMSC47B397=m
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 CONFIG_SENSORS_VIA686A=m
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1266,7 +1297,6 @@ CONFIG_SOFT_WATCHDOG=m
 #
 CONFIG_PCIPCWATCHDOG=m
 CONFIG_WDTPCI=m
-CONFIG_WDT_501_PCI=y
 
 #
 # USB-based Watchdog Cards
@@ -1289,23 +1319,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1354,6 +1370,7 @@ CONFIG_USB_MON=m
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=m
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1362,9 +1379,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=m
-CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
+CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PCI=y
 CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1545,6 +1562,10 @@ CONFIG_DMADEVICES=y
 #
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1563,11 +1584,12 @@ CONFIG_FS_MBCACHE=m
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1652,6 +1674,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1764,6 +1787,7 @@ CONFIG_HAS_DMA=y
 CONFIG_CHECK_SIGNATURE=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1794,6 +1818,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 CONFIG_DEBUG_SPINLOCK=y
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 CONFIG_DEBUG_SPINLOCK_SLEEP=y
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 CONFIG_STACKTRACE=y
@@ -1807,7 +1834,6 @@ CONFIG_DEBUG_MEMORY_INIT=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_KPROBES_SANITY_TEST is not set
@@ -1824,30 +1850,34 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_RING_BUFFER=y
+CONFIG_EVENT_TRACING=y
+CONFIG_CONTEXT_SWITCH_TRACER=y
 CONFIG_TRACING=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
 # CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_FTRACE_STARTUP_TEST is not set
+# CONFIG_RING_BUFFER_BENCHMARK is not set
 # CONFIG_DYNAMIC_DEBUG is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 CONFIG_DEBUG_STACKOVERFLOW=y
 CONFIG_DEBUG_STACK_USAGE=y
+# CONFIG_PPC_EMULATED_STATS is not set
 # CONFIG_CODE_PATCHING_SELFTEST is not set
 # CONFIG_FTR_FIXUP_SELFTEST is not set
 # CONFIG_MSI_BITMAP_SELFTEST is not set
@@ -1869,7 +1899,6 @@ CONFIG_SECURITY_NETWORK=y
 # CONFIG_SECURITY_NETWORK_XFRM is not set
 # CONFIG_SECURITY_PATH is not set
 # CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_SECURITY_DEFAULT_MMAP_MIN_ADDR=0
 CONFIG_SECURITY_SELINUX=y
 CONFIG_SECURITY_SELINUX_BOOTPARAM=y
 CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=1
diff --git a/arch/powerpc/configs/ep8248e_defconfig b/arch/powerpc/configs/ep8248e_defconfig
index 04915c3a43f..0aa5b43ffeb 100644
--- a/arch/powerpc/configs/ep8248e_defconfig
+++ b/arch/powerpc/configs/ep8248e_defconfig
@@ -1,25 +1,27 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:21:52 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:49 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -53,11 +56,13 @@ CONFIG_OF=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -99,7 +104,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -112,8 +116,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -127,6 +138,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -134,7 +149,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
 #
@@ -213,6 +228,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -228,9 +244,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -300,6 +316,7 @@ CONFIG_IP_PNP_BOOTP=y
 # CONFIG_NET_IPIP is not set
 # CONFIG_NET_IPGRE is not set
 # CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
 CONFIG_SYN_COOKIES=y
 # CONFIG_INET_AH is not set
 # CONFIG_INET_ESP is not set
@@ -380,7 +397,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 
@@ -485,6 +506,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -520,13 +542,17 @@ CONFIG_HAVE_IDE=y
 #
 
 #
-# A new alternative FireWire stack is available with EXPERIMENTAL=y
+# You can enable one or both FireWire driver stacks.
 #
+
+#
+# See the help texts for more information.
+#
+# CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_EQUALIZER is not set
@@ -573,6 +599,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_FS_ENET=y
 # CONFIG_FS_ENET_HAS_SCC is not set
@@ -594,8 +621,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 # CONFIG_FSL_PQ_MDIO is not set
 # CONFIG_GIANFAR is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_JME is not set
@@ -685,6 +714,10 @@ CONFIG_HW_RANDOM=y
 CONFIG_DEVPORT=y
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -728,22 +761,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -771,6 +789,10 @@ CONFIG_DAB=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -787,9 +809,10 @@ CONFIG_JBD=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_OCFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -935,6 +958,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -960,6 +984,9 @@ CONFIG_DEBUG_KERNEL=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -971,7 +998,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -985,22 +1011,23 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
 # CONFIG_BLK_DEV_IO_TRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/ep88xc_defconfig b/arch/powerpc/configs/ep88xc_defconfig
index c2a439595f4..2c292e25cc0 100644
--- a/arch/powerpc/configs/ep88xc_defconfig
+++ b/arch/powerpc/configs/ep88xc_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:21:53 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:49 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 # CONFIG_PPC_85xx is not set
 CONFIG_PPC_8xx=y
 # CONFIG_40x is not set
@@ -27,15 +27,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -49,11 +50,13 @@ CONFIG_OF=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -100,7 +103,6 @@ CONFIG_EMBEDDED=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -113,8 +115,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 # CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -128,13 +137,17 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
 CONFIG_BASE_SMALL=1
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -220,6 +233,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_MATH_EMULATION is not set
 CONFIG_8XX_MINIMAL_FPEMU=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
@@ -239,9 +253,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -280,6 +294,7 @@ CONFIG_PAGE_OFFSET=0xc0000000
 CONFIG_KERNEL_START=0xc0000000
 CONFIG_PHYSICAL_START=0x00000000
 CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_SIZE=0x00200000
 CONFIG_NET=y
 
 #
@@ -336,6 +351,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -353,7 +369,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -452,6 +472,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 #
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 # CONFIG_BLK_DEV is not set
 # CONFIG_MISC_DEVICES is not set
@@ -469,7 +490,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_MD is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -508,6 +528,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_FS_ENET=y
 # CONFIG_FS_ENET_HAS_SCC is not set
 CONFIG_FS_ENET_HAS_FEC=y
@@ -579,6 +600,11 @@ CONFIG_GEN_RTC=y
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -602,22 +628,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -642,6 +653,10 @@ CONFIG_DAB=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -653,12 +668,15 @@ CONFIG_DAB=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 # CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
 # CONFIG_QUOTA is not set
 # CONFIG_AUTOFS_FS is not set
 # CONFIG_AUTOFS4_FS is not set
@@ -775,6 +793,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -803,6 +822,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_SLUB_STATS is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -814,7 +836,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -827,16 +848,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -844,6 +864,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/linkstation_defconfig b/arch/powerpc/configs/linkstation_defconfig
index a4053ab9e24..45671e7dd2c 100644
--- a/arch/powerpc/configs/linkstation_defconfig
+++ b/arch/powerpc/configs/linkstation_defconfig
@@ -1,25 +1,27 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:21:54 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:50 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -52,11 +55,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -114,7 +119,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -127,9 +131,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_COMPAT_BRK is not set
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -143,6 +154,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -155,7 +170,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -237,6 +252,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 # CONFIG_BINFMT_MISC is not set
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -257,9 +273,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -480,6 +496,7 @@ CONFIG_IP_NF_ARP_MANGLE=m
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -498,7 +515,11 @@ CONFIG_WIRELESS_OLD_REGULATORY=y
 CONFIG_WIRELESS_EXT=y
 CONFIG_WIRELESS_EXT_SYSFS=y
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -647,7 +668,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 CONFIG_EEPROM_LEGACY=m
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -670,10 +693,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 CONFIG_SCSI_MULTI_LUN=y
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -691,6 +710,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -699,6 +719,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -718,7 +739,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -802,14 +822,17 @@ CONFIG_PATA_SIL680=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -846,6 +869,7 @@ CONFIG_TULIP_MMIO=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -865,8 +889,10 @@ CONFIG_R8169=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 # CONFIG_FSL_PQ_MDIO is not set
 # CONFIG_GIANFAR is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -1074,13 +1100,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -1135,6 +1165,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1169,23 +1200,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1245,6 +1262,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1254,9 +1272,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 # CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
+CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PCI=y
 CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1423,6 +1441,7 @@ CONFIG_RTC_DRV_RS5C372=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1450,6 +1469,10 @@ CONFIG_RTC_DRV_RS5C372=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1469,14 +1492,16 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 CONFIG_XFS_FS=m
 # CONFIG_XFS_QUOTA is not set
 # CONFIG_XFS_POSIX_ACL is not set
 # CONFIG_XFS_RT is not set
 # CONFIG_XFS_DEBUG is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1548,6 +1573,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=m
 CONFIG_NFSD_V3=y
@@ -1578,7 +1604,7 @@ CONFIG_CIFS=m
 #
 # CONFIG_PARTITION_ADVANCED is not set
 CONFIG_MSDOS_PARTITION=y
-CONFIG_NLS=m
+CONFIG_NLS=y
 CONFIG_NLS_DEFAULT="iso8859-1"
 CONFIG_NLS_CODEPAGE_437=m
 # CONFIG_NLS_CODEPAGE_737 is not set
@@ -1645,6 +1671,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1675,6 +1702,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1686,7 +1716,6 @@ CONFIG_DEBUG_MEMORY_INIT=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1700,16 +1729,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1717,6 +1745,8 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/mgcoge_defconfig b/arch/powerpc/configs/mgcoge_defconfig
index 31e1df66515..e9491c1c3f3 100644
--- a/arch/powerpc/configs/mgcoge_defconfig
+++ b/arch/powerpc/configs/mgcoge_defconfig
@@ -1,25 +1,27 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:21:55 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:51 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -53,6 +56,7 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 CONFIG_HIBERNATE_32=y
 CONFIG_ARCH_HIBERNATION_POSSIBLE=y
@@ -60,6 +64,7 @@ CONFIG_ARCH_HIBERNATION_POSSIBLE=y
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -105,7 +110,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -119,8 +123,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -134,6 +145,11 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -141,7 +157,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
 #
@@ -225,6 +241,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -240,9 +257,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -313,6 +330,7 @@ CONFIG_IP_PNP_BOOTP=y
 # CONFIG_NET_IPIP is not set
 # CONFIG_NET_IPGRE is not set
 # CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
 CONFIG_SYN_COOKIES=y
 # CONFIG_INET_AH is not set
 # CONFIG_INET_ESP is not set
@@ -374,7 +392,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 
@@ -484,6 +506,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -523,13 +546,17 @@ CONFIG_HAVE_IDE=y
 #
 
 #
-# A new alternative FireWire stack is available with EXPERIMENTAL=y
+# You can enable one or both FireWire driver stacks.
 #
+
+#
+# See the help texts for more information.
+#
+# CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_EQUALIZER is not set
@@ -577,6 +604,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_FS_ENET=y
 CONFIG_FS_ENET_HAS_SCC=y
@@ -654,6 +682,10 @@ CONFIG_HW_RANDOM=y
 CONFIG_DEVPORT=y
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -697,22 +729,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -740,6 +757,10 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -757,9 +778,10 @@ CONFIG_JBD=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_OCFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -916,6 +938,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -941,6 +964,9 @@ CONFIG_DEBUG_KERNEL=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -952,7 +978,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -966,16 +991,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -983,9 +1007,12 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_DYNAMIC_DEBUG is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_PPC_EMULATED_STATS is not set
 # CONFIG_CODE_PATCHING_SELFTEST is not set
 # CONFIG_FTR_FIXUP_SELFTEST is not set
 # CONFIG_MSI_BITMAP_SELFTEST is not set
diff --git a/arch/powerpc/configs/mgsuvd_defconfig b/arch/powerpc/configs/mgsuvd_defconfig
index 24fa90792c5..1ae85a3b294 100644
--- a/arch/powerpc/configs/mgsuvd_defconfig
+++ b/arch/powerpc/configs/mgsuvd_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:21:55 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:52 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 # CONFIG_PPC_85xx is not set
 CONFIG_PPC_8xx=y
 # CONFIG_40x is not set
@@ -27,15 +27,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -48,11 +49,13 @@ CONFIG_OF=y
 # CONFIG_PPC_UDBG_16550 is not set
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -102,7 +105,6 @@ CONFIG_EMBEDDED=y
 # CONFIG_SYSCTL_SYSCALL is not set
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 # CONFIG_BUG is not set
@@ -115,7 +117,14 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 # CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -129,6 +138,11 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -136,7 +150,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=1
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -222,6 +236,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
@@ -241,9 +256,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -281,6 +296,7 @@ CONFIG_PAGE_OFFSET=0xc0000000
 CONFIG_KERNEL_START=0xc0000000
 CONFIG_PHYSICAL_START=0x00000000
 CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_SIZE=0x00200000
 CONFIG_NET=y
 
 #
@@ -342,6 +358,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -359,7 +376,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -463,6 +484,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 #
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -492,7 +514,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_MD is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -531,6 +552,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_FS_ENET=y
 CONFIG_FS_ENET_HAS_SCC=y
 # CONFIG_FS_ENET_HAS_FEC is not set
@@ -602,6 +624,11 @@ CONFIG_GEN_RTC=y
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -625,22 +652,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -665,6 +677,10 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -687,10 +703,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -823,6 +841,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -844,24 +863,14 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_DYNAMIC_DEBUG is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
+# CONFIG_PPC_EMULATED_STATS is not set
 # CONFIG_IRQSTACKS is not set
 # CONFIG_VIRQ_DEBUG is not set
 # CONFIG_PPC_EARLY_DEBUG is not set
diff --git a/arch/powerpc/configs/mpc7448_hpc2_defconfig b/arch/powerpc/configs/mpc7448_hpc2_defconfig
index 642ab67c843..f23428c3b34 100644
--- a/arch/powerpc/configs/mpc7448_hpc2_defconfig
+++ b/arch/powerpc/configs/mpc7448_hpc2_defconfig
@@ -1,25 +1,27 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:21:56 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:53 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -52,11 +55,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -106,7 +111,6 @@ CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -119,9 +123,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -134,6 +145,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -141,7 +156,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-CONFIG_LBD=y
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -220,6 +235,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -240,9 +256,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -348,6 +364,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -365,7 +382,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -385,6 +406,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_CONNECTOR is not set
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -416,6 +438,7 @@ CONFIG_MISC_DEVICES=y
 # EEPROM support
 #
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -438,10 +461,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 # CONFIG_CHR_DEV_SG is not set
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -458,6 +477,7 @@ CONFIG_BLK_DEV_SD=y
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -466,6 +486,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -485,7 +506,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -568,14 +588,17 @@ CONFIG_SATA_MV=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -642,6 +665,7 @@ CONFIG_8139TOO=y
 # CONFIG_SMSC9420 is not set
 # CONFIG_SUNDANCE is not set
 # CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
 # CONFIG_VIA_RHINE is not set
 # CONFIG_SC92031 is not set
 # CONFIG_ATL2 is not set
@@ -663,7 +687,9 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_TSI108_ETH=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -785,6 +811,11 @@ CONFIG_GEN_RTC=y
 CONFIG_DEVPORT=y
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -824,22 +855,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -896,6 +912,10 @@ CONFIG_USB_ARCH_HAS_EHCI=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -915,11 +935,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1038,6 +1059,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1063,22 +1085,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/mpc8272_ads_defconfig b/arch/powerpc/configs/mpc8272_ads_defconfig
index cb966ca2ce8..02716f72db6 100644
--- a/arch/powerpc/configs/mpc8272_ads_defconfig
+++ b/arch/powerpc/configs/mpc8272_ads_defconfig
@@ -1,25 +1,27 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:21:57 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:54 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -53,11 +56,13 @@ CONFIG_OF=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -99,7 +104,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -112,9 +116,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -128,6 +139,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -135,7 +150,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
 #
@@ -216,6 +231,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -231,9 +247,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -303,6 +319,7 @@ CONFIG_IP_PNP_BOOTP=y
 # CONFIG_NET_IPIP is not set
 # CONFIG_NET_IPGRE is not set
 # CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
 CONFIG_SYN_COOKIES=y
 # CONFIG_INET_AH is not set
 # CONFIG_INET_ESP is not set
@@ -383,7 +400,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 
@@ -489,6 +510,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -524,13 +546,17 @@ CONFIG_HAVE_IDE=y
 #
 
 #
-# A new alternative FireWire stack is available with EXPERIMENTAL=y
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
+# CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_EQUALIZER is not set
@@ -577,6 +603,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_FS_ENET=y
 # CONFIG_FS_ENET_HAS_SCC is not set
@@ -598,8 +625,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 # CONFIG_FSL_PQ_MDIO is not set
 # CONFIG_GIANFAR is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_JME is not set
@@ -671,12 +700,13 @@ CONFIG_INPUT_EVDEV=y
 #
 CONFIG_INPUT_KEYBOARD=y
 CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
 # CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_MATRIX is not set
 # CONFIG_KEYBOARD_NEWTON is not set
 # CONFIG_KEYBOARD_STOWAWAY is not set
-# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
 CONFIG_INPUT_MOUSE=y
 CONFIG_MOUSE_PS2=y
 CONFIG_MOUSE_PS2_ALPS=y
@@ -741,6 +771,10 @@ CONFIG_HW_RANDOM=y
 CONFIG_DEVPORT=y
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -784,22 +818,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -828,6 +847,10 @@ CONFIG_DAB=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -847,9 +870,10 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_OCFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -998,6 +1022,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1028,6 +1053,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1039,7 +1067,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1053,22 +1080,23 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
 # CONFIG_BLK_DEV_IO_TRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/mpc83xx_defconfig b/arch/powerpc/configs/mpc83xx_defconfig
index 433c303eb82..4a96cb6925b 100644
--- a/arch/powerpc/configs/mpc83xx_defconfig
+++ b/arch/powerpc/configs/mpc83xx_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:21:58 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:55 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_FSL_EMB_PERFMON is not set
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -31,15 +33,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -54,6 +57,7 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 CONFIG_REDBOOT=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
@@ -61,6 +65,7 @@ CONFIG_ARCH_SUSPEND_POSSIBLE=y
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -110,7 +115,6 @@ CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -123,8 +127,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -138,6 +149,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -150,7 +165,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -192,6 +207,7 @@ CONFIG_MPC837x_MDS=y
 CONFIG_MPC837x_RDB=y
 CONFIG_SBC834x=y
 CONFIG_ASP834x=y
+# CONFIG_KMETER1 is not set
 CONFIG_PPC_MPC831x=y
 CONFIG_PPC_MPC832x=y
 CONFIG_PPC_MPC834x=y
@@ -241,6 +257,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -261,9 +278,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -374,6 +391,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -391,7 +409,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -507,6 +529,7 @@ CONFIG_MTD_NAND_FSL_ELBC=y
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -542,7 +565,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -565,10 +590,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -586,6 +607,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -594,6 +616,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -613,7 +636,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -697,14 +719,17 @@ CONFIG_ATA_SFF=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -751,6 +776,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -770,11 +796,13 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
 CONFIG_UCC_GETH=y
 # CONFIG_UGETH_MAGIC_PACKET is not set
 # CONFIG_UGETH_TX_ON_DEMAND is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -965,13 +993,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -1050,6 +1082,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1104,24 +1137,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1159,7 +1177,7 @@ CONFIG_HID_BELKIN=y
 CONFIG_HID_CHERRY=y
 CONFIG_HID_CHICONY=y
 CONFIG_HID_CYPRESS=y
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 CONFIG_HID_EZKEY=y
 # CONFIG_HID_KYE is not set
 CONFIG_HID_GYRATION=y
@@ -1176,10 +1194,11 @@ CONFIG_HID_PETALYNX=y
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-CONFIG_THRUSTMASTER_FF=m
-CONFIG_ZEROPLUS_FF=m
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1205,6 +1224,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1291,6 +1311,10 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1310,10 +1334,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1377,6 +1403,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1413,7 +1440,46 @@ CONFIG_MSDOS_PARTITION=y
 # CONFIG_KARMA_PARTITION is not set
 # CONFIG_EFI_PARTITION is not set
 # CONFIG_SYSV68_PARTITION is not set
-# CONFIG_NLS is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
 # CONFIG_DLM is not set
 CONFIG_UCC_FAST=y
 CONFIG_UCC=y
@@ -1438,6 +1504,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1461,22 +1528,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/mpc85xx_defconfig b/arch/powerpc/configs/mpc85xx_defconfig
index c162724fed4..ada595898af 100644
--- a/arch/powerpc/configs/mpc85xx_defconfig
+++ b/arch/powerpc/configs/mpc85xx_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc2
-# Tue Apr 21 15:40:23 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:55 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -34,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -57,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -116,7 +119,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -129,9 +131,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -146,6 +155,11 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -158,7 +172,7 @@ CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-CONFIG_LBD=y
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -191,6 +205,7 @@ CONFIG_MPC8536_DS=y
 CONFIG_MPC85xx_DS=y
 CONFIG_SOCRATES=y
 CONFIG_KSI8560=y
+# CONFIG_XES_MPC85xx is not set
 CONFIG_STX_GP3=y
 CONFIG_TQM8540=y
 CONFIG_TQM8541=y
@@ -241,7 +256,9 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=m
 CONFIG_MATH_EMULATION=y
-# CONFIG_IOMMU_HELPER is not set
+CONFIG_IOMMU_HELPER=y
+CONFIG_SWIOTLB=y
+CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -260,9 +277,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -296,7 +313,8 @@ CONFIG_ARCH_SUPPORTS_MSI=y
 # CONFIG_PCI_IOV is not set
 # CONFIG_PCCARD is not set
 # CONFIG_HOTPLUG_PCI is not set
-# CONFIG_HAS_RAPIDIO is not set
+CONFIG_HAS_RAPIDIO=y
+# CONFIG_RAPIDIO is not set
 
 #
 # Advanced setup
@@ -406,6 +424,7 @@ CONFIG_SCTP_HMAC_MD5=y
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -424,7 +443,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -450,6 +473,7 @@ CONFIG_EXTRA_FIRMWARE=""
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -485,7 +509,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 CONFIG_EEPROM_LEGACY=y
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -509,10 +535,6 @@ CONFIG_BLK_DEV_SR=y
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 CONFIG_SCSI_MULTI_LUN=y
 # CONFIG_SCSI_CONSTANTS is not set
 CONFIG_SCSI_LOGGING=y
@@ -530,6 +552,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -538,6 +561,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -557,7 +581,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -641,14 +664,17 @@ CONFIG_PATA_ALI=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=y
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -695,6 +721,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_FS_ENET=y
 CONFIG_FS_ENET_HAS_SCC=y
@@ -718,11 +745,13 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
 CONFIG_UCC_GETH=y
 # CONFIG_UGETH_MAGIC_PACKET is not set
 # CONFIG_UGETH_TX_ON_DEMAND is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -897,6 +926,7 @@ CONFIG_I2C_HELPER_AUTO=y
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
 CONFIG_I2C_CPM=m
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_GPIO is not set
 CONFIG_I2C_MPC=y
 # CONFIG_I2C_OCORES is not set
@@ -927,13 +957,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -987,76 +1021,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-CONFIG_DVB_CORE=m
-CONFIG_VIDEO_MEDIA=m
-
-#
-# Multimedia drivers
-#
-# CONFIG_MEDIA_ATTACH is not set
-CONFIG_MEDIA_TUNER=m
-# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
-CONFIG_MEDIA_TUNER_SIMPLE=m
-CONFIG_MEDIA_TUNER_TDA8290=m
-CONFIG_MEDIA_TUNER_TDA9887=m
-CONFIG_MEDIA_TUNER_TEA5761=m
-CONFIG_MEDIA_TUNER_TEA5767=m
-CONFIG_MEDIA_TUNER_MT20XX=m
-CONFIG_MEDIA_TUNER_XC2028=m
-CONFIG_MEDIA_TUNER_XC5000=m
-CONFIG_MEDIA_TUNER_MC44S803=m
-# CONFIG_DVB_DYNAMIC_MINORS is not set
-CONFIG_DVB_CAPTURE_DRIVERS=y
-
-#
-# Supported SAA7146 based PCI Adapters
-#
-# CONFIG_TTPCI_EEPROM is not set
-# CONFIG_DVB_BUDGET_CORE is not set
-
-#
-# Supported USB Adapters
-#
-# CONFIG_DVB_USB is not set
-# CONFIG_DVB_TTUSB_BUDGET is not set
-# CONFIG_DVB_TTUSB_DEC is not set
-# CONFIG_DVB_SIANO_SMS1XXX is not set
-
-#
-# Supported FlexCopII (B2C2) Adapters
-#
-# CONFIG_DVB_B2C2_FLEXCOP is not set
-
-#
-# Supported BT878 Adapters
-#
-
-#
-# Supported Pluto2 Adapters
-#
-# CONFIG_DVB_PLUTO2 is not set
-
-#
-# Supported SDMC DM1105 Adapters
-#
-# CONFIG_DVB_DM1105 is not set
-
-#
-# Supported DVB Frontends
-#
-# CONFIG_DVB_FE_CUSTOMISE is not set
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1096,6 +1063,11 @@ CONFIG_SND_VERBOSE_PROCFS=y
 # CONFIG_SND_VERBOSE_PRINTK is not set
 # CONFIG_SND_DEBUG is not set
 CONFIG_SND_VMASTER=y
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
 CONFIG_SND_AC97_CODEC=y
 CONFIG_SND_DRIVERS=y
 # CONFIG_SND_DUMMY is not set
@@ -1122,6 +1094,7 @@ CONFIG_SND_PCI=y
 # CONFIG_SND_CS4281 is not set
 # CONFIG_SND_CS46XX is not set
 # CONFIG_SND_CS5530 is not set
+# CONFIG_SND_CTXFI is not set
 # CONFIG_SND_DARLA20 is not set
 # CONFIG_SND_GINA20 is not set
 # CONFIG_SND_LAYLA20 is not set
@@ -1152,6 +1125,7 @@ CONFIG_SND_PCI=y
 CONFIG_SND_INTEL8X0=y
 # CONFIG_SND_INTEL8X0M is not set
 # CONFIG_SND_KORG1212 is not set
+# CONFIG_SND_LX6464ES is not set
 # CONFIG_SND_MAESTRO3 is not set
 # CONFIG_SND_MIXART is not set
 # CONFIG_SND_NM256 is not set
@@ -1196,7 +1170,7 @@ CONFIG_HID_BELKIN=y
 CONFIG_HID_CHERRY=y
 CONFIG_HID_CHICONY=y
 CONFIG_HID_CYPRESS=y
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 CONFIG_HID_EZKEY=y
 # CONFIG_HID_KYE is not set
 CONFIG_HID_GYRATION=y
@@ -1213,10 +1187,11 @@ CONFIG_HID_PETALYNX=y
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-CONFIG_THRUSTMASTER_FF=m
-CONFIG_ZEROPLUS_FF=m
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1242,6 +1217,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1251,9 +1227,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 CONFIG_USB_OHCI_HCD_PPC_OF_LE=y
+CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PCI=y
 CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1352,8 +1328,6 @@ CONFIG_EDAC=y
 # CONFIG_EDAC_DEBUG is not set
 CONFIG_EDAC_MM_EDAC=y
 CONFIG_EDAC_MPC85XX=y
-# CONFIG_EDAC_AMD8131 is not set
-# CONFIG_EDAC_AMD8111 is not set
 CONFIG_RTC_LIB=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_HCTOSYS=y
@@ -1385,6 +1359,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1425,6 +1400,10 @@ CONFIG_DMA_ENGINE=y
 # CONFIG_DMATEST is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1445,11 +1424,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1524,6 +1504,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
 # CONFIG_NFSD_V3 is not set
@@ -1628,6 +1609,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1658,6 +1640,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1670,7 +1655,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1684,16 +1668,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1702,9 +1685,13 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_PPC_EMULATED_STATS is not set
 # CONFIG_CODE_PATCHING_SELFTEST is not set
 # CONFIG_FTR_FIXUP_SELFTEST is not set
 # CONFIG_MSI_BITMAP_SELFTEST is not set
diff --git a/arch/powerpc/configs/mpc85xx_smp_defconfig b/arch/powerpc/configs/mpc85xx_smp_defconfig
index 1aa1c508d60..db082ce5a1c 100644
--- a/arch/powerpc/configs/mpc85xx_smp_defconfig
+++ b/arch/powerpc/configs/mpc85xx_smp_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc2
-# Tue Apr 21 15:41:18 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:56 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 CONFIG_PPC_85xx=y
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
@@ -35,15 +35,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -58,11 +59,13 @@ CONFIG_PPC_UDBG_16550=y
 CONFIG_GENERIC_TBSYNC=y
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -117,7 +120,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -130,9 +132,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -148,6 +157,11 @@ CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_USE_GENERIC_SMP_HELPERS=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -161,7 +175,7 @@ CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
-CONFIG_LBD=y
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -194,6 +208,7 @@ CONFIG_MPC8536_DS=y
 CONFIG_MPC85xx_DS=y
 CONFIG_SOCRATES=y
 CONFIG_KSI8560=y
+# CONFIG_XES_MPC85xx is not set
 CONFIG_STX_GP3=y
 CONFIG_TQM8540=y
 CONFIG_TQM8541=y
@@ -244,7 +259,9 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=m
 CONFIG_MATH_EMULATION=y
-# CONFIG_IOMMU_HELPER is not set
+CONFIG_IOMMU_HELPER=y
+CONFIG_SWIOTLB=y
+CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -264,9 +281,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -300,7 +317,8 @@ CONFIG_ARCH_SUPPORTS_MSI=y
 # CONFIG_PCI_IOV is not set
 # CONFIG_PCCARD is not set
 # CONFIG_HOTPLUG_PCI is not set
-# CONFIG_HAS_RAPIDIO is not set
+CONFIG_HAS_RAPIDIO=y
+# CONFIG_RAPIDIO is not set
 
 #
 # Advanced setup
@@ -410,6 +428,7 @@ CONFIG_SCTP_HMAC_MD5=y
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -428,7 +447,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -454,6 +477,7 @@ CONFIG_EXTRA_FIRMWARE=""
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -489,7 +513,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 CONFIG_EEPROM_LEGACY=y
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -513,10 +539,6 @@ CONFIG_BLK_DEV_SR=y
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 CONFIG_SCSI_MULTI_LUN=y
 # CONFIG_SCSI_CONSTANTS is not set
 CONFIG_SCSI_LOGGING=y
@@ -534,6 +556,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -542,6 +565,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -561,7 +585,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -645,14 +668,17 @@ CONFIG_PATA_ALI=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=y
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -699,6 +725,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_FS_ENET=y
 CONFIG_FS_ENET_HAS_SCC=y
@@ -722,11 +749,13 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
 CONFIG_UCC_GETH=y
 # CONFIG_UGETH_MAGIC_PACKET is not set
 # CONFIG_UGETH_TX_ON_DEMAND is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -901,6 +930,7 @@ CONFIG_I2C_HELPER_AUTO=y
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
 CONFIG_I2C_CPM=m
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_GPIO is not set
 CONFIG_I2C_MPC=y
 # CONFIG_I2C_OCORES is not set
@@ -931,13 +961,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -991,76 +1025,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-CONFIG_DVB_CORE=m
-CONFIG_VIDEO_MEDIA=m
-
-#
-# Multimedia drivers
-#
-# CONFIG_MEDIA_ATTACH is not set
-CONFIG_MEDIA_TUNER=m
-# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
-CONFIG_MEDIA_TUNER_SIMPLE=m
-CONFIG_MEDIA_TUNER_TDA8290=m
-CONFIG_MEDIA_TUNER_TDA9887=m
-CONFIG_MEDIA_TUNER_TEA5761=m
-CONFIG_MEDIA_TUNER_TEA5767=m
-CONFIG_MEDIA_TUNER_MT20XX=m
-CONFIG_MEDIA_TUNER_XC2028=m
-CONFIG_MEDIA_TUNER_XC5000=m
-CONFIG_MEDIA_TUNER_MC44S803=m
-# CONFIG_DVB_DYNAMIC_MINORS is not set
-CONFIG_DVB_CAPTURE_DRIVERS=y
-
-#
-# Supported SAA7146 based PCI Adapters
-#
-# CONFIG_TTPCI_EEPROM is not set
-# CONFIG_DVB_BUDGET_CORE is not set
-
-#
-# Supported USB Adapters
-#
-# CONFIG_DVB_USB is not set
-# CONFIG_DVB_TTUSB_BUDGET is not set
-# CONFIG_DVB_TTUSB_DEC is not set
-# CONFIG_DVB_SIANO_SMS1XXX is not set
-
-#
-# Supported FlexCopII (B2C2) Adapters
-#
-# CONFIG_DVB_B2C2_FLEXCOP is not set
-
-#
-# Supported BT878 Adapters
-#
-
-#
-# Supported Pluto2 Adapters
-#
-# CONFIG_DVB_PLUTO2 is not set
-
-#
-# Supported SDMC DM1105 Adapters
-#
-# CONFIG_DVB_DM1105 is not set
-
-#
-# Supported DVB Frontends
-#
-# CONFIG_DVB_FE_CUSTOMISE is not set
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1100,6 +1067,11 @@ CONFIG_SND_VERBOSE_PROCFS=y
 # CONFIG_SND_VERBOSE_PRINTK is not set
 # CONFIG_SND_DEBUG is not set
 CONFIG_SND_VMASTER=y
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
 CONFIG_SND_AC97_CODEC=y
 CONFIG_SND_DRIVERS=y
 # CONFIG_SND_DUMMY is not set
@@ -1126,6 +1098,7 @@ CONFIG_SND_PCI=y
 # CONFIG_SND_CS4281 is not set
 # CONFIG_SND_CS46XX is not set
 # CONFIG_SND_CS5530 is not set
+# CONFIG_SND_CTXFI is not set
 # CONFIG_SND_DARLA20 is not set
 # CONFIG_SND_GINA20 is not set
 # CONFIG_SND_LAYLA20 is not set
@@ -1156,6 +1129,7 @@ CONFIG_SND_PCI=y
 CONFIG_SND_INTEL8X0=y
 # CONFIG_SND_INTEL8X0M is not set
 # CONFIG_SND_KORG1212 is not set
+# CONFIG_SND_LX6464ES is not set
 # CONFIG_SND_MAESTRO3 is not set
 # CONFIG_SND_MIXART is not set
 # CONFIG_SND_NM256 is not set
@@ -1200,7 +1174,7 @@ CONFIG_HID_BELKIN=y
 CONFIG_HID_CHERRY=y
 CONFIG_HID_CHICONY=y
 CONFIG_HID_CYPRESS=y
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 CONFIG_HID_EZKEY=y
 # CONFIG_HID_KYE is not set
 CONFIG_HID_GYRATION=y
@@ -1217,10 +1191,11 @@ CONFIG_HID_PETALYNX=y
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-CONFIG_THRUSTMASTER_FF=m
-CONFIG_ZEROPLUS_FF=m
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1246,6 +1221,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1255,9 +1231,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 CONFIG_USB_OHCI_HCD_PPC_OF_LE=y
+CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PCI=y
 CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1356,8 +1332,6 @@ CONFIG_EDAC=y
 # CONFIG_EDAC_DEBUG is not set
 CONFIG_EDAC_MM_EDAC=y
 CONFIG_EDAC_MPC85XX=y
-# CONFIG_EDAC_AMD8131 is not set
-# CONFIG_EDAC_AMD8111 is not set
 CONFIG_RTC_LIB=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_HCTOSYS=y
@@ -1389,6 +1363,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1429,6 +1404,10 @@ CONFIG_DMA_ENGINE=y
 # CONFIG_DMATEST is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1449,11 +1428,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1528,6 +1508,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
 # CONFIG_NFSD_V3 is not set
@@ -1632,6 +1613,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1662,6 +1644,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1674,7 +1659,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1688,16 +1672,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1706,9 +1689,13 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_PPC_EMULATED_STATS is not set
 # CONFIG_CODE_PATCHING_SELFTEST is not set
 # CONFIG_FTR_FIXUP_SELFTEST is not set
 # CONFIG_MSI_BITMAP_SELFTEST is not set
diff --git a/arch/powerpc/configs/mpc866_ads_defconfig b/arch/powerpc/configs/mpc866_ads_defconfig
index 3add6f62b21..6809b61ed3d 100644
--- a/arch/powerpc/configs/mpc866_ads_defconfig
+++ b/arch/powerpc/configs/mpc866_ads_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:00 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:57 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 # CONFIG_PPC_85xx is not set
 CONFIG_PPC_8xx=y
 # CONFIG_40x is not set
@@ -27,15 +27,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -48,11 +49,13 @@ CONFIG_OF=y
 # CONFIG_PPC_UDBG_16550 is not set
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -98,7 +101,6 @@ CONFIG_EMBEDDED=y
 # CONFIG_SYSCTL_SYSCALL is not set
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 # CONFIG_BUG is not set
@@ -111,8 +113,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 # CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -126,6 +135,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -133,7 +146,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=1
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -219,6 +232,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
 CONFIG_MATH_EMULATION=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
@@ -238,9 +252,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -278,6 +292,7 @@ CONFIG_PAGE_OFFSET=0xc0000000
 CONFIG_KERNEL_START=0xc0000000
 CONFIG_PHYSICAL_START=0x00000000
 CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_SIZE=0x00200000
 CONFIG_NET=y
 
 #
@@ -339,6 +354,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -356,7 +372,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -374,6 +394,7 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y
 # CONFIG_CONNECTOR is not set
 # CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -407,7 +428,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_MD is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -446,6 +466,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_FS_ENET=y
 CONFIG_FS_ENET_HAS_SCC=y
 CONFIG_FS_ENET_HAS_FEC=y
@@ -453,6 +474,7 @@ CONFIG_FS_ENET_MDIO_FEC=y
 CONFIG_NETDEV_1000=y
 # CONFIG_FSL_PQ_MDIO is not set
 # CONFIG_GIANFAR is not set
+# CONFIG_MV643XX_ETH is not set
 CONFIG_NETDEV_10000=y
 
 #
@@ -496,11 +518,11 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
 #
 CONFIG_INPUT_KEYBOARD=y
 CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
 # CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
 # CONFIG_KEYBOARD_NEWTON is not set
 # CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
 CONFIG_INPUT_MOUSE=y
 CONFIG_MOUSE_PS2=y
 CONFIG_MOUSE_PS2_ALPS=y
@@ -562,6 +584,11 @@ CONFIG_GEN_RTC=y
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -597,22 +624,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -664,6 +676,10 @@ CONFIG_USB_SUPPORT=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -685,10 +701,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -808,6 +826,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -831,22 +850,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_PPC_EARLY_DEBUG is not set
diff --git a/arch/powerpc/configs/mpc86xx_defconfig b/arch/powerpc/configs/mpc86xx_defconfig
index 5bb1b8eb0b4..0e8684a3138 100644
--- a/arch/powerpc/configs/mpc86xx_defconfig
+++ b/arch/powerpc/configs/mpc86xx_defconfig
@@ -1,26 +1,28 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:00 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:58 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_PHYS_64BIT is not set
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_PPC32=y
@@ -32,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -55,11 +58,13 @@ CONFIG_PPC_UDBG_16550=y
 CONFIG_GENERIC_TBSYNC=y
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -114,7 +119,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -127,9 +131,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -144,6 +155,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_USE_GENERIC_SMP_HELPERS=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -157,7 +172,7 @@ CONFIG_MODVERSIONS=y
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
-CONFIG_LBD=y
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -236,7 +251,9 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=m
-# CONFIG_IOMMU_HELPER is not set
+CONFIG_IOMMU_HELPER=y
+CONFIG_SWIOTLB=y
+CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -258,9 +275,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -403,6 +420,7 @@ CONFIG_SCTP_HMAC_MD5=y
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -421,7 +439,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -447,6 +469,7 @@ CONFIG_EXTRA_FIRMWARE=""
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -482,7 +505,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 CONFIG_EEPROM_LEGACY=y
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -506,10 +531,6 @@ CONFIG_BLK_DEV_SR=y
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 CONFIG_CHR_DEV_SG=y
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 CONFIG_SCSI_MULTI_LUN=y
 # CONFIG_SCSI_CONSTANTS is not set
 CONFIG_SCSI_LOGGING=y
@@ -527,6 +548,7 @@ CONFIG_SCSI_WAIT_SCAN=m
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -535,6 +557,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -554,7 +577,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -638,14 +660,17 @@ CONFIG_PATA_ALI=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=y
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -692,6 +717,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -711,8 +737,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_FSL_PQ_MDIO=y
 CONFIG_GIANFAR=y
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -913,13 +941,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -973,76 +1005,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-CONFIG_DVB_CORE=m
-CONFIG_VIDEO_MEDIA=m
-
-#
-# Multimedia drivers
-#
-# CONFIG_MEDIA_ATTACH is not set
-CONFIG_MEDIA_TUNER=m
-# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
-CONFIG_MEDIA_TUNER_SIMPLE=m
-CONFIG_MEDIA_TUNER_TDA8290=m
-CONFIG_MEDIA_TUNER_TDA9887=m
-CONFIG_MEDIA_TUNER_TEA5761=m
-CONFIG_MEDIA_TUNER_TEA5767=m
-CONFIG_MEDIA_TUNER_MT20XX=m
-CONFIG_MEDIA_TUNER_XC2028=m
-CONFIG_MEDIA_TUNER_XC5000=m
-CONFIG_MEDIA_TUNER_MC44S803=m
-# CONFIG_DVB_DYNAMIC_MINORS is not set
-CONFIG_DVB_CAPTURE_DRIVERS=y
-
-#
-# Supported SAA7146 based PCI Adapters
-#
-# CONFIG_TTPCI_EEPROM is not set
-# CONFIG_DVB_BUDGET_CORE is not set
-
-#
-# Supported USB Adapters
-#
-# CONFIG_DVB_USB is not set
-# CONFIG_DVB_TTUSB_BUDGET is not set
-# CONFIG_DVB_TTUSB_DEC is not set
-# CONFIG_DVB_SIANO_SMS1XXX is not set
-
-#
-# Supported FlexCopII (B2C2) Adapters
-#
-# CONFIG_DVB_B2C2_FLEXCOP is not set
-
-#
-# Supported BT878 Adapters
-#
-
-#
-# Supported Pluto2 Adapters
-#
-# CONFIG_DVB_PLUTO2 is not set
-
-#
-# Supported SDMC DM1105 Adapters
-#
-# CONFIG_DVB_DM1105 is not set
-
-#
-# Supported DVB Frontends
-#
-# CONFIG_DVB_FE_CUSTOMISE is not set
-CONFIG_DAB=y
-# CONFIG_USB_DABUSB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1082,6 +1047,11 @@ CONFIG_SND_VERBOSE_PROCFS=y
 # CONFIG_SND_VERBOSE_PRINTK is not set
 # CONFIG_SND_DEBUG is not set
 CONFIG_SND_VMASTER=y
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
 CONFIG_SND_AC97_CODEC=y
 CONFIG_SND_DRIVERS=y
 # CONFIG_SND_DUMMY is not set
@@ -1108,6 +1078,7 @@ CONFIG_SND_PCI=y
 # CONFIG_SND_CS4281 is not set
 # CONFIG_SND_CS46XX is not set
 # CONFIG_SND_CS5530 is not set
+# CONFIG_SND_CTXFI is not set
 # CONFIG_SND_DARLA20 is not set
 # CONFIG_SND_GINA20 is not set
 # CONFIG_SND_LAYLA20 is not set
@@ -1138,6 +1109,7 @@ CONFIG_SND_PCI=y
 CONFIG_SND_INTEL8X0=y
 # CONFIG_SND_INTEL8X0M is not set
 # CONFIG_SND_KORG1212 is not set
+# CONFIG_SND_LX6464ES is not set
 # CONFIG_SND_MAESTRO3 is not set
 # CONFIG_SND_MIXART is not set
 # CONFIG_SND_NM256 is not set
@@ -1182,7 +1154,7 @@ CONFIG_HID_BELKIN=y
 CONFIG_HID_CHERRY=y
 CONFIG_HID_CHICONY=y
 CONFIG_HID_CYPRESS=y
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
 CONFIG_HID_EZKEY=y
 # CONFIG_HID_KYE is not set
 CONFIG_HID_GYRATION=y
@@ -1199,10 +1171,11 @@ CONFIG_HID_PETALYNX=y
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
 # CONFIG_HID_TOPSEED is not set
-CONFIG_THRUSTMASTER_FF=m
-CONFIG_ZEROPLUS_FF=m
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1228,6 +1201,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1237,9 +1211,9 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
 CONFIG_USB_OHCI_HCD_PPC_OF_LE=y
+CONFIG_USB_OHCI_HCD_PPC_OF=y
 CONFIG_USB_OHCI_HCD_PCI=y
 CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1360,6 +1334,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1387,6 +1362,10 @@ CONFIG_RTC_DRV_CMOS=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1406,11 +1385,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1485,6 +1465,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
 # CONFIG_NFSD_V3 is not set
@@ -1586,6 +1567,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1616,6 +1598,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1628,7 +1613,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1642,16 +1626,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -1659,6 +1642,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/mpc885_ads_defconfig b/arch/powerpc/configs/mpc885_ads_defconfig
index 42e64ebc279..dbe8e869a82 100644
--- a/arch/powerpc/configs/mpc885_ads_defconfig
+++ b/arch/powerpc/configs/mpc885_ads_defconfig
@@ -1,14 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:01 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:31:59 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-# CONFIG_6xx is not set
+# CONFIG_PPC_BOOK3S_32 is not set
 # CONFIG_PPC_85xx is not set
 CONFIG_PPC_8xx=y
 # CONFIG_40x is not set
@@ -27,15 +27,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -49,11 +50,13 @@ CONFIG_OF=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -100,7 +103,6 @@ CONFIG_EMBEDDED=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -113,8 +115,15 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 # CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -128,13 +137,17 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
 CONFIG_BASE_SMALL=1
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -227,6 +240,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_MATH_EMULATION is not set
 CONFIG_8XX_MINIMAL_FPEMU=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
@@ -246,9 +260,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -287,6 +301,7 @@ CONFIG_PAGE_OFFSET=0xc0000000
 CONFIG_KERNEL_START=0xc0000000
 CONFIG_PHYSICAL_START=0x00000000
 CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_SIZE=0x00200000
 CONFIG_NET=y
 
 #
@@ -343,6 +358,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -360,7 +376,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -463,6 +483,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 #
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 # CONFIG_BLK_DEV is not set
 # CONFIG_MISC_DEVICES is not set
@@ -480,7 +501,6 @@ CONFIG_HAVE_IDE=y
 # CONFIG_MD is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -519,6 +539,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_FS_ENET=y
 # CONFIG_FS_ENET_HAS_SCC is not set
 CONFIG_FS_ENET_HAS_FEC=y
@@ -590,6 +611,11 @@ CONFIG_GEN_RTC=y
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -613,22 +639,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -653,6 +664,10 @@ CONFIG_DAB=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -664,12 +679,15 @@ CONFIG_DAB=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 # CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
 # CONFIG_QUOTA is not set
 # CONFIG_AUTOFS_FS is not set
 # CONFIG_AUTOFS4_FS is not set
@@ -786,6 +804,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -814,6 +833,9 @@ CONFIG_SCHED_DEBUG=y
 # CONFIG_SLUB_STATS is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -825,7 +847,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -838,16 +859,15 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
@@ -855,6 +875,9 @@ CONFIG_TRACING_SUPPORT=y
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/pq2fads_defconfig b/arch/powerpc/configs/pq2fads_defconfig
index 129d80860f2..ff96bb43c32 100644
--- a/arch/powerpc/configs/pq2fads_defconfig
+++ b/arch/powerpc/configs/pq2fads_defconfig
@@ -1,25 +1,27 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:02 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:00 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_GENERIC_GPIO=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
@@ -53,11 +56,13 @@ CONFIG_OF=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 CONFIG_DEFAULT_UIMAGE=y
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -103,7 +108,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -116,9 +120,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -132,6 +143,10 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -139,7 +154,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
 #
@@ -219,6 +234,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -234,9 +250,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -307,6 +323,7 @@ CONFIG_IP_PNP_BOOTP=y
 # CONFIG_NET_IPIP is not set
 # CONFIG_NET_IPGRE is not set
 # CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
 CONFIG_SYN_COOKIES=y
 # CONFIG_INET_AH is not set
 # CONFIG_INET_ESP is not set
@@ -387,7 +404,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 
@@ -493,6 +514,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_GPIO=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -518,6 +540,7 @@ CONFIG_MISC_DEVICES=y
 # EEPROM support
 #
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -583,13 +606,17 @@ CONFIG_IDE_PROC_FS=y
 #
 
 #
-# A new alternative FireWire stack is available with EXPERIMENTAL=y
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
+# CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_EQUALIZER is not set
@@ -636,6 +663,7 @@ CONFIG_MII=y
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_FS_ENET=y
 # CONFIG_FS_ENET_HAS_SCC is not set
@@ -657,8 +685,10 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 # CONFIG_FSL_PQ_MDIO is not set
 # CONFIG_GIANFAR is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_JME is not set
@@ -730,12 +760,13 @@ CONFIG_INPUT_EVDEV=y
 #
 CONFIG_INPUT_KEYBOARD=y
 CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
 # CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_MATRIX is not set
 # CONFIG_KEYBOARD_NEWTON is not set
 # CONFIG_KEYBOARD_STOWAWAY is not set
-# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
 CONFIG_INPUT_MOUSE=y
 CONFIG_MOUSE_PS2=y
 CONFIG_MOUSE_PS2_ALPS=y
@@ -802,6 +833,10 @@ CONFIG_HW_RANDOM=y
 CONFIG_DEVPORT=y
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
@@ -845,22 +880,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -903,8 +923,9 @@ CONFIG_USB_GADGET_SELECTED=y
 # CONFIG_USB_GADGET_OMAP is not set
 # CONFIG_USB_GADGET_PXA25X is not set
 # CONFIG_USB_GADGET_PXA27X is not set
-# CONFIG_USB_GADGET_S3C2410 is not set
+# CONFIG_USB_GADGET_S3C_HSOTG is not set
 # CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
 CONFIG_USB_GADGET_M66592=y
 CONFIG_USB_M66592=y
 # CONFIG_USB_GADGET_AMD5536UDC is not set
@@ -912,9 +933,11 @@ CONFIG_USB_M66592=y
 # CONFIG_USB_GADGET_CI13XXX is not set
 # CONFIG_USB_GADGET_NET2280 is not set
 # CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LANGWELL is not set
 # CONFIG_USB_GADGET_DUMMY_HCD is not set
 CONFIG_USB_GADGET_DUALSPEED=y
 # CONFIG_USB_ZERO is not set
+# CONFIG_USB_AUDIO is not set
 CONFIG_USB_ETH=y
 CONFIG_USB_ETH_RNDIS=y
 # CONFIG_USB_GADGETFS is not set
@@ -939,6 +962,10 @@ CONFIG_USB_ETH_RNDIS=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -958,9 +985,10 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_OCFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1110,6 +1138,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1140,6 +1169,9 @@ CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
 # CONFIG_RT_MUTEX_TESTER is not set
 # CONFIG_DEBUG_SPINLOCK is not set
 # CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
 # CONFIG_DEBUG_SPINLOCK_SLEEP is not set
 # CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 # CONFIG_DEBUG_KOBJECT is not set
@@ -1151,7 +1183,6 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_LIST is not set
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1165,22 +1196,23 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
+CONFIG_FTRACE=y
 # CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
 # CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
 # CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
 # CONFIG_STACK_TRACER is not set
 # CONFIG_KMEMTRACE is not set
 # CONFIG_WORKQUEUE_TRACER is not set
 # CONFIG_BLK_DEV_IO_TRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
diff --git a/arch/powerpc/configs/prpmc2800_defconfig b/arch/powerpc/configs/prpmc2800_defconfig
index e9f287f313f..1293c465d7f 100644
--- a/arch/powerpc/configs/prpmc2800_defconfig
+++ b/arch/powerpc/configs/prpmc2800_defconfig
@@ -1,25 +1,27 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:03 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:01 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_NOT_COHERENT_CACHE=y
 CONFIG_CHECK_CACHE_COHERENCY=y
@@ -32,15 +34,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -54,11 +57,13 @@ CONFIG_OF=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -114,7 +119,6 @@ CONFIG_ANON_INODES=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -127,9 +131,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -142,6 +153,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -149,7 +164,7 @@ CONFIG_RT_MUTEXES=y
 CONFIG_BASE_SMALL=0
 # CONFIG_MODULES is not set
 CONFIG_BLOCK=y
-CONFIG_LBD=y
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -228,6 +243,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_PPC_NEED_DMA_SYNC_OPS=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
@@ -249,9 +265,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -296,6 +312,7 @@ CONFIG_PAGE_OFFSET=0xc0000000
 CONFIG_KERNEL_START=0xc0000000
 CONFIG_PHYSICAL_START=0x00000000
 CONFIG_TASK_SIZE=0xc0000000
+CONFIG_CONSISTENT_SIZE=0x00200000
 CONFIG_NET=y
 
 #
@@ -357,6 +374,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -374,7 +392,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -479,6 +501,7 @@ CONFIG_MTD_PHYSMAP_OF=y
 # CONFIG_MTD_UBI is not set
 CONFIG_OF_DEVICE=y
 CONFIG_OF_I2C=y
+CONFIG_OF_MDIO=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_FD is not set
@@ -514,7 +537,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -591,10 +616,6 @@ CONFIG_BLK_DEV_SD=y
 # CONFIG_BLK_DEV_SR is not set
 # CONFIG_CHR_DEV_SG is not set
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -611,6 +632,7 @@ CONFIG_BLK_DEV_SD=y
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -619,6 +641,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -638,7 +661,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_IPR is not set
@@ -721,7 +743,11 @@ CONFIG_SATA_MV=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
@@ -730,7 +756,6 @@ CONFIG_MACINTOSH_DRIVERS=y
 # CONFIG_MAC_EMUMOUSEBTN is not set
 # CONFIG_WINDFARM is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -797,6 +822,7 @@ CONFIG_8139TOO=y
 # CONFIG_SMSC9420 is not set
 # CONFIG_SUNDANCE is not set
 # CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
 # CONFIG_VIA_RHINE is not set
 # CONFIG_SC92031 is not set
 # CONFIG_ATL2 is not set
@@ -818,6 +844,7 @@ CONFIG_E1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 CONFIG_MV643XX_ETH=y
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
@@ -1007,13 +1034,17 @@ CONFIG_I2C_MV64XXX=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -1068,6 +1099,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -1102,23 +1134,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1163,6 +1181,7 @@ CONFIG_HID_BELKIN=y
 CONFIG_HID_CHERRY=y
 CONFIG_HID_CHICONY=y
 CONFIG_HID_CYPRESS=y
+CONFIG_HID_DRAGONRISE=y
 # CONFIG_DRAGONRISE_FF is not set
 CONFIG_HID_EZKEY=y
 CONFIG_HID_KYE=y
@@ -1180,9 +1199,14 @@ CONFIG_HID_PETALYNX=y
 CONFIG_HID_SAMSUNG=y
 CONFIG_HID_SONY=y
 CONFIG_HID_SUNPLUS=y
+CONFIG_HID_GREENASIA=y
 # CONFIG_GREENASIA_FF is not set
+CONFIG_HID_SMARTJOYPLUS=y
+# CONFIG_SMARTJOYPLUS_FF is not set
 CONFIG_HID_TOPSEED=y
+CONFIG_HID_THRUSTMASTER=y
 CONFIG_THRUSTMASTER_FF=y
+CONFIG_HID_ZEROPLUS=y
 CONFIG_ZEROPLUS_FF=y
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
@@ -1207,6 +1231,7 @@ CONFIG_USB_MON=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1215,6 +1240,8 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
 # CONFIG_USB_OHCI_HCD_PPC_OF is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
@@ -1322,6 +1349,7 @@ CONFIG_RTC_DRV_MAX6900=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1349,6 +1377,10 @@ CONFIG_RTC_DRV_MAX6900=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1368,11 +1400,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1469,7 +1502,46 @@ CONFIG_MSDOS_PARTITION=y
 # CONFIG_KARMA_PARTITION is not set
 # CONFIG_EFI_PARTITION is not set
 # CONFIG_SYSV68_PARTITION is not set
-# CONFIG_NLS is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
 # CONFIG_DLM is not set
 # CONFIG_BINARY_PRINTF is not set
 
@@ -1494,6 +1566,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1519,22 +1592,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
diff --git a/arch/powerpc/configs/storcenter_defconfig b/arch/powerpc/configs/storcenter_defconfig
index bd4a8d435c5..28384dc0100 100644
--- a/arch/powerpc/configs/storcenter_defconfig
+++ b/arch/powerpc/configs/storcenter_defconfig
@@ -1,25 +1,27 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc3
-# Wed May 13 17:22:04 2009
+# Linux kernel version: 2.6.31-rc4
+# Wed Jul 29 23:32:01 2009
 #
 # CONFIG_PPC64 is not set
 
 #
 # Processor support
 #
-CONFIG_6xx=y
+CONFIG_PPC_BOOK3S_32=y
 # CONFIG_PPC_85xx is not set
 # CONFIG_PPC_8xx is not set
 # CONFIG_40x is not set
 # CONFIG_44x is not set
 # CONFIG_E200 is not set
 CONFIG_PPC_BOOK3S=y
+CONFIG_6xx=y
 CONFIG_PPC_FPU=y
 # CONFIG_ALTIVEC is not set
 CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_32=y
 # CONFIG_PPC_MM_SLICES is not set
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 # CONFIG_SMP is not set
 CONFIG_PPC32=y
 CONFIG_WORD_SIZE=32
@@ -30,15 +32,16 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
 CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
 CONFIG_LOCKDEP_SUPPORT=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 # CONFIG_ARCH_NO_VIRT_TO_BUS is not set
 CONFIG_PPC=y
@@ -52,11 +55,13 @@ CONFIG_PPC_UDBG_16550=y
 # CONFIG_GENERIC_TBSYNC is not set
 CONFIG_AUDIT_ARCH=y
 CONFIG_GENERIC_BUG=y
+CONFIG_DTC=y
 # CONFIG_DEFAULT_UIMAGE is not set
 # CONFIG_PPC_DCR_NATIVE is not set
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -101,7 +106,6 @@ CONFIG_ANON_INODES=y
 CONFIG_EMBEDDED=y
 CONFIG_SYSCTL_SYSCALL=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -114,9 +118,16 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
 CONFIG_SLUB_DEBUG=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 # CONFIG_SLAB is not set
 CONFIG_SLUB=y
@@ -129,6 +140,10 @@ CONFIG_HAVE_IOREMAP_PROT=y
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -141,7 +156,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-CONFIG_LBD=y
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -222,6 +237,7 @@ CONFIG_BINFMT_ELF=y
 # CONFIG_HAVE_AOUT is not set
 CONFIG_BINFMT_MISC=y
 # CONFIG_IOMMU_HELPER is not set
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -242,9 +258,9 @@ CONFIG_MIGRATION=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_PPC_4K_PAGES=y
 # CONFIG_PPC_16K_PAGES is not set
 # CONFIG_PPC_64K_PAGES is not set
@@ -347,6 +363,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -364,7 +381,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -501,7 +522,9 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 CONFIG_IDE=y
 
@@ -579,10 +602,6 @@ CONFIG_BLK_DEV_SR=y
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 # CONFIG_CHR_DEV_SG is not set
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -599,6 +618,7 @@ CONFIG_SCSI_SPI_ATTRS=y
 # CONFIG_SCSI_SRP_ATTRS is not set
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -607,6 +627,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_DPT_I2O is not set
 # CONFIG_SCSI_ADVANSYS is not set
 # CONFIG_SCSI_ARCMSR is not set
@@ -626,7 +647,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_QLOGIC_1280 is not set
@@ -660,14 +680,17 @@ CONFIG_MD_RAID6_PQ=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=m
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -695,8 +718,10 @@ CONFIG_R8169=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 # CONFIG_FSL_PQ_MDIO is not set
 # CONFIG_GIANFAR is not set
+# CONFIG_MV643XX_ETH is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -845,13 +870,17 @@ CONFIG_I2C_MPC=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -879,23 +908,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -937,6 +952,7 @@ CONFIG_USB_DEVICE_CLASS=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=y
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -946,6 +962,8 @@ CONFIG_USB_EHCI_HCD_PPC_OF=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
 # CONFIG_USB_OHCI_HCD_PPC_OF is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
@@ -1064,6 +1082,7 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1091,6 +1110,10 @@ CONFIG_RTC_DRV_DS1307=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1110,7 +1133,6 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 CONFIG_XFS_FS=m
 # CONFIG_XFS_QUOTA is not set
 # CONFIG_XFS_POSIX_ACL is not set
@@ -1119,6 +1141,8 @@ CONFIG_XFS_FS=m
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1273,6 +1297,7 @@ CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
+CONFIG_GENERIC_ATOMIC64=y
 
 #
 # Kernel hacking
@@ -1298,22 +1323,11 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_FTRACE is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 # CONFIG_IRQSTACKS is not set
 # CONFIG_BOOTX_TEXT is not set
-- 
GitLab


From f294526279cda8934b0313ebd02184a16ba888c9 Mon Sep 17 00:00:00 2001
From: Dan Carpenter <error27@gmail.com>
Date: Sun, 19 Jul 2009 14:46:09 +0300
Subject: [PATCH 0303/1153] lguest: dereferencing freed mem in add_eventfd()

"new" was freed and then dereferenced.  Also the return value wasn't being
used so I modified the caller as well.

Compile tested only.  Found by smatch (http://repo.or.cz/w/smatch.git).

regards,
dan carpenter

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
---
 drivers/lguest/lguest_user.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/lguest/lguest_user.c b/drivers/lguest/lguest_user.c
index 9f9a2953b38..407722a8e0c 100644
--- a/drivers/lguest/lguest_user.c
+++ b/drivers/lguest/lguest_user.c
@@ -52,8 +52,9 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd)
 	new->map[new->num].addr = addr;
 	new->map[new->num].event = eventfd_ctx_fdget(fd);
 	if (IS_ERR(new->map[new->num].event)) {
+		int err =  PTR_ERR(new->map[new->num].event);
 		kfree(new);
-		return PTR_ERR(new->map[new->num].event);
+		return err;
 	}
 	new->num++;
 
@@ -83,7 +84,7 @@ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input)
 	err = add_eventfd(lg, addr, fd);
 	mutex_unlock(&lguest_lock);
 
-	return 0;
+	return err;
 }
 
 /*L:050 Sending an interrupt is done by writing LHREQ_IRQ and an interrupt
-- 
GitLab


From 8ef562d112c82ec539775698f8b63ac5ec1bd766 Mon Sep 17 00:00:00 2001
From: Rusty Russell <rusty@rustcorp.com.au>
Date: Thu, 30 Jul 2009 16:03:43 -0600
Subject: [PATCH 0304/1153] lguest: fix descriptor corruption in example
 launcher

1d589bb16b825b3a7b4edd34d997f1f1f953033d "Add serial number support
for virtio_blk, V4a" extended 'struct virtio_blk_config' to 536 bytes.
Lguest and S/390 both use an 8 bit value for the feature length, and
this change broke them (if the code is naive).

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: John Cooper <john.cooper@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
---
 Documentation/lguest/lguest.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c
index 9ebcd6ef361..45d7d6dcae7 100644
--- a/Documentation/lguest/lguest.c
+++ b/Documentation/lguest/lguest.c
@@ -1105,6 +1105,9 @@ static void set_config(struct device *dev, unsigned len, const void *conf)
 	/* Copy in the config information, and store the length. */
 	memcpy(device_config(dev), conf, len);
 	dev->desc->config_len = len;
+
+	/* Size must fit in config_len field (8 bits)! */
+	assert(dev->desc->config_len == len);
 }
 
 /* This routine does all the creation and setup of a new device, including
@@ -1515,7 +1518,8 @@ static void setup_block_file(const char *filename)
 	add_feature(dev, VIRTIO_BLK_F_SEG_MAX);
 	conf.seg_max = cpu_to_le32(VIRTQUEUE_NUM - 2);
 
-	set_config(dev, sizeof(conf), &conf);
+	/* Don't try to put whole struct: we have 8 bit limit. */
+	set_config(dev, offsetof(struct virtio_blk_config, geometry), &conf);
 
 	verbose("device %u: virtblock %llu sectors\n",
 		++devices.device_num, le64_to_cpu(conf.capacity));
-- 
GitLab


From ff52c3fc7188855ede75d87b022271f0da309e5b Mon Sep 17 00:00:00 2001
From: "Michael S. Tsirkin" <mst@redhat.com>
Date: Thu, 23 Jul 2009 14:57:37 +0300
Subject: [PATCH 0305/1153] virtio: fix memory leak on device removal

Make vp_free_vectors do the reverse of vq_request_vectors.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
---
 drivers/virtio/virtio_pci.c | 28 +++++++++++++++-------------
 1 file changed, 15 insertions(+), 13 deletions(-)

diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c
index bcec78ffc76..ca40517ef9c 100644
--- a/drivers/virtio/virtio_pci.c
+++ b/drivers/virtio/virtio_pci.c
@@ -258,7 +258,6 @@ static void vp_free_vectors(struct virtio_device *vdev)
 
 	for (i = 0; i < vp_dev->msix_used_vectors; ++i)
 		free_irq(vp_dev->msix_entries[i].vector, vp_dev);
-	vp_dev->msix_used_vectors = 0;
 
 	if (vp_dev->msix_enabled) {
 		/* Disable the vector used for configuration */
@@ -267,9 +266,16 @@ static void vp_free_vectors(struct virtio_device *vdev)
 		/* Flush the write out to device */
 		ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR);
 
-		vp_dev->msix_enabled = 0;
 		pci_disable_msix(vp_dev->pci_dev);
+		vp_dev->msix_enabled = 0;
+		vp_dev->msix_vectors = 0;
 	}
+
+	vp_dev->msix_used_vectors = 0;
+	kfree(vp_dev->msix_names);
+	vp_dev->msix_names = NULL;
+	kfree(vp_dev->msix_entries);
+	vp_dev->msix_entries = NULL;
 }
 
 static int vp_enable_msix(struct pci_dev *dev, struct msix_entry *entries,
@@ -297,11 +303,11 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs)
 	vp_dev->msix_entries = kmalloc(nvectors * sizeof *vp_dev->msix_entries,
 				       GFP_KERNEL);
 	if (!vp_dev->msix_entries)
-		goto error_entries;
+		goto error;
 	vp_dev->msix_names = kmalloc(nvectors * sizeof *vp_dev->msix_names,
 				     GFP_KERNEL);
 	if (!vp_dev->msix_names)
-		goto error_names;
+		goto error;
 
 	for (i = 0; i < nvectors; ++i)
 		vp_dev->msix_entries[i].entry = i;
@@ -314,7 +320,7 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs)
 		err = request_irq(vp_dev->pci_dev->irq, vp_interrupt,
 				  IRQF_SHARED, name, vp_dev);
 		if (err)
-			goto error_irq;
+			goto error;
 		vp_dev->intx_enabled = 1;
 	} else {
 		vp_dev->msix_vectors = err;
@@ -328,7 +334,7 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs)
 				  vp_config_changed, 0, vp_dev->msix_names[v],
 				  vp_dev);
 		if (err)
-			goto error_irq;
+			goto error;
 		++vp_dev->msix_used_vectors;
 
 		iowrite16(v, vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR);
@@ -336,7 +342,7 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs)
 		v = ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR);
 		if (v == VIRTIO_MSI_NO_VECTOR) {
 			err = -EBUSY;
-			goto error_irq;
+			goto error;
 		}
 	}
 
@@ -349,16 +355,12 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs)
 				  vp_vring_interrupt, 0, vp_dev->msix_names[v],
 				  vp_dev);
 		if (err)
-			goto error_irq;
+			goto error;
 		++vp_dev->msix_used_vectors;
 	}
 	return 0;
-error_irq:
+error:
 	vp_free_vectors(vdev);
-	kfree(vp_dev->msix_names);
-error_names:
-	kfree(vp_dev->msix_entries);
-error_entries:
 	return err;
 }
 
-- 
GitLab


From f6c82507030d61e15928d5cad946d3eac1c4a384 Mon Sep 17 00:00:00 2001
From: "Michael S. Tsirkin" <mst@redhat.com>
Date: Sun, 26 Jul 2009 15:48:01 +0300
Subject: [PATCH 0306/1153] virtio: delete vq from list

This makes delete vq the reverse of find vq.
This is required to make it possible to retry find_vqs
after a failure, otherwise the list gets corrupted.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
---
 drivers/virtio/virtio_pci.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c
index ca40517ef9c..a1cb1a1c652 100644
--- a/drivers/virtio/virtio_pci.c
+++ b/drivers/virtio/virtio_pci.c
@@ -464,7 +464,11 @@ static void vp_del_vq(struct virtqueue *vq)
 {
 	struct virtio_pci_device *vp_dev = to_vp_device(vq->vdev);
 	struct virtio_pci_vq_info *info = vq->priv;
-	unsigned long size;
+	unsigned long flags, size;
+
+	spin_lock_irqsave(&vp_dev->lock, flags);
+	list_del(&info->node);
+	spin_unlock_irqrestore(&vp_dev->lock, flags);
 
 	iowrite16(info->queue_index, vp_dev->ioaddr + VIRTIO_PCI_QUEUE_SEL);
 
-- 
GitLab


From e969fed542cae08cb11d666efac4f7c5d624d09f Mon Sep 17 00:00:00 2001
From: "Michael S. Tsirkin" <mst@redhat.com>
Date: Sun, 26 Jul 2009 15:48:08 +0300
Subject: [PATCH 0307/1153] virtio: refactor find_vqs

This refactors find_vqs, making it more readable and robust, and fixing
two regressions from 2.6.30:
- double free_irq causing BUG_ON on device removal
- probe failure when vq can't be assigned to msi-x vector
  (reported on old host kernels)

Tested-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
---
 drivers/virtio/virtio_pci.c | 212 ++++++++++++++++++++----------------
 1 file changed, 119 insertions(+), 93 deletions(-)

diff --git a/drivers/virtio/virtio_pci.c b/drivers/virtio/virtio_pci.c
index a1cb1a1c652..248e00ec4dc 100644
--- a/drivers/virtio/virtio_pci.c
+++ b/drivers/virtio/virtio_pci.c
@@ -52,8 +52,10 @@ struct virtio_pci_device
 	char (*msix_names)[256];
 	/* Number of available vectors */
 	unsigned msix_vectors;
-	/* Vectors allocated */
+	/* Vectors allocated, excluding per-vq vectors if any */
 	unsigned msix_used_vectors;
+	/* Whether we have vector per vq */
+	bool per_vq_vectors;
 };
 
 /* Constants for MSI-X */
@@ -278,27 +280,24 @@ static void vp_free_vectors(struct virtio_device *vdev)
 	vp_dev->msix_entries = NULL;
 }
 
-static int vp_enable_msix(struct pci_dev *dev, struct msix_entry *entries,
-			  int *options, int noptions)
-{
-	int i;
-	for (i = 0; i < noptions; ++i)
-		if (!pci_enable_msix(dev, entries, options[i]))
-			return options[i];
-	return -EBUSY;
-}
-
-static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs)
+static int vp_request_vectors(struct virtio_device *vdev, int nvectors,
+			      bool per_vq_vectors)
 {
 	struct virtio_pci_device *vp_dev = to_vp_device(vdev);
 	const char *name = dev_name(&vp_dev->vdev.dev);
 	unsigned i, v;
 	int err = -ENOMEM;
-	/* We want at most one vector per queue and one for config changes.
-	 * Fallback to separate vectors for config and a shared for queues.
-	 * Finally fall back to regular interrupts. */
-	int options[] = { max_vqs + 1, 2 };
-	int nvectors = max(options[0], options[1]);
+
+	if (!nvectors) {
+		/* Can't allocate MSI-X vectors, use regular interrupt */
+		vp_dev->msix_vectors = 0;
+		err = request_irq(vp_dev->pci_dev->irq, vp_interrupt,
+				  IRQF_SHARED, name, vp_dev);
+		if (err)
+			return err;
+		vp_dev->intx_enabled = 1;
+		return 0;
+	}
 
 	vp_dev->msix_entries = kmalloc(nvectors * sizeof *vp_dev->msix_entries,
 				       GFP_KERNEL);
@@ -312,41 +311,34 @@ static int vp_request_vectors(struct virtio_device *vdev, unsigned max_vqs)
 	for (i = 0; i < nvectors; ++i)
 		vp_dev->msix_entries[i].entry = i;
 
-	err = vp_enable_msix(vp_dev->pci_dev, vp_dev->msix_entries,
-			     options, ARRAY_SIZE(options));
-	if (err < 0) {
-		/* Can't allocate enough MSI-X vectors, use regular interrupt */
-		vp_dev->msix_vectors = 0;
-		err = request_irq(vp_dev->pci_dev->irq, vp_interrupt,
-				  IRQF_SHARED, name, vp_dev);
-		if (err)
-			goto error;
-		vp_dev->intx_enabled = 1;
-	} else {
-		vp_dev->msix_vectors = err;
-		vp_dev->msix_enabled = 1;
-
-		/* Set the vector used for configuration */
-		v = vp_dev->msix_used_vectors;
-		snprintf(vp_dev->msix_names[v], sizeof *vp_dev->msix_names,
-			 "%s-config", name);
-		err = request_irq(vp_dev->msix_entries[v].vector,
-				  vp_config_changed, 0, vp_dev->msix_names[v],
-				  vp_dev);
-		if (err)
-			goto error;
-		++vp_dev->msix_used_vectors;
+	err = pci_enable_msix(vp_dev->pci_dev, vp_dev->msix_entries, nvectors);
+	if (err > 0)
+		err = -ENOSPC;
+	if (err)
+		goto error;
+	vp_dev->msix_vectors = nvectors;
+	vp_dev->msix_enabled = 1;
+
+	/* Set the vector used for configuration */
+	v = vp_dev->msix_used_vectors;
+	snprintf(vp_dev->msix_names[v], sizeof *vp_dev->msix_names,
+		 "%s-config", name);
+	err = request_irq(vp_dev->msix_entries[v].vector,
+			  vp_config_changed, 0, vp_dev->msix_names[v],
+			  vp_dev);
+	if (err)
+		goto error;
+	++vp_dev->msix_used_vectors;
 
-		iowrite16(v, vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR);
-		/* Verify we had enough resources to assign the vector */
-		v = ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR);
-		if (v == VIRTIO_MSI_NO_VECTOR) {
-			err = -EBUSY;
-			goto error;
-		}
+	iowrite16(v, vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR);
+	/* Verify we had enough resources to assign the vector */
+	v = ioread16(vp_dev->ioaddr + VIRTIO_MSI_CONFIG_VECTOR);
+	if (v == VIRTIO_MSI_NO_VECTOR) {
+		err = -EBUSY;
+		goto error;
 	}
 
-	if (vp_dev->msix_vectors && vp_dev->msix_vectors != max_vqs + 1) {
+	if (!per_vq_vectors) {
 		/* Shared vector for all VQs */
 		v = vp_dev->msix_used_vectors;
 		snprintf(vp_dev->msix_names[v], sizeof *vp_dev->msix_names,
@@ -366,13 +358,14 @@ error:
 
 static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index,
 				    void (*callback)(struct virtqueue *vq),
-				    const char *name)
+				    const char *name,
+				    u16 vector)
 {
 	struct virtio_pci_device *vp_dev = to_vp_device(vdev);
 	struct virtio_pci_vq_info *info;
 	struct virtqueue *vq;
 	unsigned long flags, size;
-	u16 num, vector;
+	u16 num;
 	int err;
 
 	/* Select the queue we're interested in */
@@ -391,7 +384,7 @@ static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index,
 
 	info->queue_index = index;
 	info->num = num;
-	info->vector = VIRTIO_MSI_NO_VECTOR;
+	info->vector = vector;
 
 	size = PAGE_ALIGN(vring_size(num, VIRTIO_PCI_VRING_ALIGN));
 	info->queue = alloc_pages_exact(size, GFP_KERNEL|__GFP_ZERO);
@@ -415,22 +408,7 @@ static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index,
 	vq->priv = info;
 	info->vq = vq;
 
-	/* allocate per-vq vector if available and necessary */
-	if (callback && vp_dev->msix_used_vectors < vp_dev->msix_vectors) {
-		vector = vp_dev->msix_used_vectors;
-		snprintf(vp_dev->msix_names[vector], sizeof *vp_dev->msix_names,
-			 "%s-%s", dev_name(&vp_dev->vdev.dev), name);
-		err = request_irq(vp_dev->msix_entries[vector].vector,
-				  vring_interrupt, 0,
-				  vp_dev->msix_names[vector], vq);
-		if (err)
-			goto out_request_irq;
-		info->vector = vector;
-		++vp_dev->msix_used_vectors;
-	} else
-		vector = VP_MSIX_VQ_VECTOR;
-
-	 if (callback && vp_dev->msix_enabled) {
+	 if (vector != VIRTIO_MSI_NO_VECTOR) {
 		iowrite16(vector, vp_dev->ioaddr + VIRTIO_MSI_QUEUE_VECTOR);
 		vector = ioread16(vp_dev->ioaddr + VIRTIO_MSI_QUEUE_VECTOR);
 		if (vector == VIRTIO_MSI_NO_VECTOR) {
@@ -446,11 +424,6 @@ static struct virtqueue *vp_find_vq(struct virtio_device *vdev, unsigned index,
 	return vq;
 
 out_assign:
-	if (info->vector != VIRTIO_MSI_NO_VECTOR) {
-		free_irq(vp_dev->msix_entries[info->vector].vector, vq);
-		--vp_dev->msix_used_vectors;
-	}
-out_request_irq:
 	vring_del_virtqueue(vq);
 out_activate_queue:
 	iowrite32(0, vp_dev->ioaddr + VIRTIO_PCI_QUEUE_PFN);
@@ -472,9 +445,6 @@ static void vp_del_vq(struct virtqueue *vq)
 
 	iowrite16(info->queue_index, vp_dev->ioaddr + VIRTIO_PCI_QUEUE_SEL);
 
-	if (info->vector != VIRTIO_MSI_NO_VECTOR)
-		free_irq(vp_dev->msix_entries[info->vector].vector, vq);
-
 	if (vp_dev->msix_enabled) {
 		iowrite16(VIRTIO_MSI_NO_VECTOR,
 			  vp_dev->ioaddr + VIRTIO_MSI_QUEUE_VECTOR);
@@ -495,36 +465,62 @@ static void vp_del_vq(struct virtqueue *vq)
 /* the config->del_vqs() implementation */
 static void vp_del_vqs(struct virtio_device *vdev)
 {
+	struct virtio_pci_device *vp_dev = to_vp_device(vdev);
 	struct virtqueue *vq, *n;
+	struct virtio_pci_vq_info *info;
 
-	list_for_each_entry_safe(vq, n, &vdev->vqs, list)
+	list_for_each_entry_safe(vq, n, &vdev->vqs, list) {
+		info = vq->priv;
+		if (vp_dev->per_vq_vectors)
+			free_irq(vp_dev->msix_entries[info->vector].vector, vq);
 		vp_del_vq(vq);
+	}
+	vp_dev->per_vq_vectors = false;
 
 	vp_free_vectors(vdev);
 }
 
-/* the config->find_vqs() implementation */
-static int vp_find_vqs(struct virtio_device *vdev, unsigned nvqs,
-		       struct virtqueue *vqs[],
-		       vq_callback_t *callbacks[],
-		       const char *names[])
+static int vp_try_to_find_vqs(struct virtio_device *vdev, unsigned nvqs,
+			      struct virtqueue *vqs[],
+			      vq_callback_t *callbacks[],
+			      const char *names[],
+			      int nvectors,
+			      bool per_vq_vectors)
 {
-	int vectors = 0;
-	int i, err;
-
-	/* How many vectors would we like? */
-	for (i = 0; i < nvqs; ++i)
-		if (callbacks[i])
-			++vectors;
+	struct virtio_pci_device *vp_dev = to_vp_device(vdev);
+	u16 vector;
+	int i, err, allocated_vectors;
 
-	err = vp_request_vectors(vdev, vectors);
+	err = vp_request_vectors(vdev, nvectors, per_vq_vectors);
 	if (err)
 		goto error_request;
 
+	vp_dev->per_vq_vectors = per_vq_vectors;
+	allocated_vectors = vp_dev->msix_used_vectors;
 	for (i = 0; i < nvqs; ++i) {
-		vqs[i] = vp_find_vq(vdev, i, callbacks[i], names[i]);
-		if (IS_ERR(vqs[i]))
+		if (!callbacks[i] || !vp_dev->msix_enabled)
+			vector = VIRTIO_MSI_NO_VECTOR;
+		else if (vp_dev->per_vq_vectors)
+			vector = allocated_vectors++;
+		else
+			vector = VP_MSIX_VQ_VECTOR;
+		vqs[i] = vp_find_vq(vdev, i, callbacks[i], names[i], vector);
+		if (IS_ERR(vqs[i])) {
+			err = PTR_ERR(vqs[i]);
 			goto error_find;
+		}
+		/* allocate per-vq irq if available and necessary */
+		if (vp_dev->per_vq_vectors && vector != VIRTIO_MSI_NO_VECTOR) {
+			snprintf(vp_dev->msix_names[vector], sizeof *vp_dev->msix_names,
+				 "%s-%s", dev_name(&vp_dev->vdev.dev), names[i]);
+			err = request_irq(vp_dev->msix_entries[vector].vector,
+					  vring_interrupt, 0,
+					  vp_dev->msix_names[vector], vqs[i]);
+			if (err) {
+				vp_del_vq(vqs[i]);
+				goto error_find;
+			}
+		}
 	}
 	return 0;
 
@@ -532,7 +528,37 @@ error_find:
 	vp_del_vqs(vdev);
 
 error_request:
-	return PTR_ERR(vqs[i]);
+	return err;
+}
+
+/* the config->find_vqs() implementation */
+static int vp_find_vqs(struct virtio_device *vdev, unsigned nvqs,
+		       struct virtqueue *vqs[],
+		       vq_callback_t *callbacks[],
+		       const char *names[])
+{
+	int vectors = 0;
+	int i, uninitialized_var(err);
+
+	/* How many vectors would we like? */
+	for (i = 0; i < nvqs; ++i)
+		if (callbacks[i])
+			++vectors;
+
+	/* We want at most one vector per queue and one for config changes. */
+	err = vp_try_to_find_vqs(vdev, nvqs, vqs, callbacks, names,
+				 vectors + 1, true);
+	if (!err)
+		return 0;
+	/* Fallback to separate vectors for config and a shared for queues. */
+	err = vp_try_to_find_vqs(vdev, nvqs, vqs, callbacks, names,
+				 2, false);
+	if (!err)
+		return 0;
+	/* Finally fall back to regular interrupts. */
+	err = vp_try_to_find_vqs(vdev, nvqs, vqs, callbacks, names,
+				 0, false);
+	return err;
 }
 
 static struct virtio_config_ops virtio_pci_config_ops = {
-- 
GitLab


From 2e04ef76916d1e29a077ea9d0f2003c8fd86724d Mon Sep 17 00:00:00 2001
From: Rusty Russell <rusty@rustcorp.com.au>
Date: Thu, 30 Jul 2009 16:03:45 -0600
Subject: [PATCH 0308/1153] lguest: fix comment style

I don't really notice it (except to begrudge the extra vertical
space), but Ingo does.  And he pointed out that one excuse of lguest
is as a teaching tool, it should set a good example.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
---
 Documentation/lguest/lguest.c         | 540 +++++++++++++++++---------
 arch/x86/include/asm/lguest.h         |   3 +-
 arch/x86/include/asm/lguest_hcall.h   |  10 +-
 arch/x86/lguest/boot.c                | 428 +++++++++++++-------
 arch/x86/lguest/i386_head.S           | 110 ++++--
 drivers/lguest/core.c                 | 114 ++++--
 drivers/lguest/hypercalls.c           | 141 ++++---
 drivers/lguest/interrupts_and_traps.c | 288 +++++++++-----
 drivers/lguest/lg.h                   |  23 +-
 drivers/lguest/lguest_device.c        | 150 ++++---
 drivers/lguest/lguest_user.c          | 137 ++++---
 drivers/lguest/page_tables.c          | 427 +++++++++++++-------
 drivers/lguest/segments.c             | 106 +++--
 drivers/lguest/x86/core.c             | 372 ++++++++++++------
 drivers/lguest/x86/switcher_32.S      |  18 +-
 include/linux/lguest.h                |  36 +-
 include/linux/lguest_launcher.h       |  18 +-
 17 files changed, 1906 insertions(+), 1015 deletions(-)

diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c
index 45d7d6dcae7..aa66a52b73e 100644
--- a/Documentation/lguest/lguest.c
+++ b/Documentation/lguest/lguest.c
@@ -1,7 +1,9 @@
-/*P:100 This is the Launcher code, a simple program which lays out the
- * "physical" memory for the new Guest by mapping the kernel image and
- * the virtual devices, then opens /dev/lguest to tell the kernel
- * about the Guest and control it. :*/
+/*P:100
+ * This is the Launcher code, a simple program which lays out the "physical"
+ * memory for the new Guest by mapping the kernel image and the virtual
+ * devices, then opens /dev/lguest to tell the kernel about the Guest and
+ * control it.
+:*/
 #define _LARGEFILE64_SOURCE
 #define _GNU_SOURCE
 #include <stdio.h>
@@ -46,13 +48,15 @@
 #include "linux/virtio_rng.h"
 #include "linux/virtio_ring.h"
 #include "asm/bootparam.h"
-/*L:110 We can ignore the 39 include files we need for this program, but I do
- * want to draw attention to the use of kernel-style types.
+/*L:110
+ * We can ignore the 39 include files we need for this program, but I do want
+ * to draw attention to the use of kernel-style types.
  *
  * As Linus said, "C is a Spartan language, and so should your naming be."  I
  * like these abbreviations, so we define them here.  Note that u64 is always
  * unsigned long long, which works on all Linux systems: this means that we can
- * use %llu in printf for any u64. */
+ * use %llu in printf for any u64.
+ */
 typedef unsigned long long u64;
 typedef uint32_t u32;
 typedef uint16_t u16;
@@ -69,8 +73,10 @@ typedef uint8_t u8;
 /* This will occupy 3 pages: it must be a power of 2. */
 #define VIRTQUEUE_NUM 256
 
-/*L:120 verbose is both a global flag and a macro.  The C preprocessor allows
- * this, and although I wouldn't recommend it, it works quite nicely here. */
+/*L:120
+ * verbose is both a global flag and a macro.  The C preprocessor allows
+ * this, and although I wouldn't recommend it, it works quite nicely here.
+ */
 static bool verbose;
 #define verbose(args...) \
 	do { if (verbose) printf(args); } while(0)
@@ -100,8 +106,7 @@ struct device_list
 
 	/* A single linked list of devices. */
 	struct device *dev;
-	/* And a pointer to the last device for easy append and also for
-	 * configuration appending. */
+	/* And a pointer to the last device for easy append. */
 	struct device *lastdev;
 };
 
@@ -168,20 +173,24 @@ static char **main_args;
 /* The original tty settings to restore on exit. */
 static struct termios orig_term;
 
-/* We have to be careful with barriers: our devices are all run in separate
+/*
+ * We have to be careful with barriers: our devices are all run in separate
  * threads and so we need to make sure that changes visible to the Guest happen
- * in precise order. */
+ * in precise order.
+ */
 #define wmb() __asm__ __volatile__("" : : : "memory")
 #define mb() __asm__ __volatile__("" : : : "memory")
 
-/* Convert an iovec element to the given type.
+/*
+ * Convert an iovec element to the given type.
  *
  * This is a fairly ugly trick: we need to know the size of the type and
  * alignment requirement to check the pointer is kosher.  It's also nice to
  * have the name of the type in case we report failure.
  *
  * Typing those three things all the time is cumbersome and error prone, so we
- * have a macro which sets them all up and passes to the real function. */
+ * have a macro which sets them all up and passes to the real function.
+ */
 #define convert(iov, type) \
 	((type *)_convert((iov), sizeof(type), __alignof__(type), #type))
 
@@ -198,8 +207,10 @@ static void *_convert(struct iovec *iov, size_t size, size_t align,
 /* Wrapper for the last available index.  Makes it easier to change. */
 #define lg_last_avail(vq)	((vq)->last_avail_idx)
 
-/* The virtio configuration space is defined to be little-endian.  x86 is
- * little-endian too, but it's nice to be explicit so we have these helpers. */
+/*
+ * The virtio configuration space is defined to be little-endian.  x86 is
+ * little-endian too, but it's nice to be explicit so we have these helpers.
+ */
 #define cpu_to_le16(v16) (v16)
 #define cpu_to_le32(v32) (v32)
 #define cpu_to_le64(v64) (v64)
@@ -241,11 +252,12 @@ static u8 *get_feature_bits(struct device *dev)
 		+ dev->num_vq * sizeof(struct lguest_vqconfig);
 }
 
-/*L:100 The Launcher code itself takes us out into userspace, that scary place
- * where pointers run wild and free!  Unfortunately, like most userspace
- * programs, it's quite boring (which is why everyone likes to hack on the
- * kernel!).  Perhaps if you make up an Lguest Drinking Game at this point, it
- * will get you through this section.  Or, maybe not.
+/*L:100
+ * The Launcher code itself takes us out into userspace, that scary place where
+ * pointers run wild and free!  Unfortunately, like most userspace programs,
+ * it's quite boring (which is why everyone likes to hack on the kernel!).
+ * Perhaps if you make up an Lguest Drinking Game at this point, it will get
+ * you through this section.  Or, maybe not.
  *
  * The Launcher sets up a big chunk of memory to be the Guest's "physical"
  * memory and stores it in "guest_base".  In other words, Guest physical ==
@@ -253,7 +265,8 @@ static u8 *get_feature_bits(struct device *dev)
  *
  * This can be tough to get your head around, but usually it just means that we
  * use these trivial conversion functions when the Guest gives us it's
- * "physical" addresses: */
+ * "physical" addresses:
+ */
 static void *from_guest_phys(unsigned long addr)
 {
 	return guest_base + addr;
@@ -268,7 +281,8 @@ static unsigned long to_guest_phys(const void *addr)
  * Loading the Kernel.
  *
  * We start with couple of simple helper routines.  open_or_die() avoids
- * error-checking code cluttering the callers: */
+ * error-checking code cluttering the callers:
+ */
 static int open_or_die(const char *name, int flags)
 {
 	int fd = open(name, flags);
@@ -283,8 +297,10 @@ static void *map_zeroed_pages(unsigned int num)
 	int fd = open_or_die("/dev/zero", O_RDONLY);
 	void *addr;
 
-	/* We use a private mapping (ie. if we write to the page, it will be
-	 * copied). */
+	/*
+	 * We use a private mapping (ie. if we write to the page, it will be
+	 * copied).
+	 */
 	addr = mmap(NULL, getpagesize() * num,
 		    PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE, fd, 0);
 	if (addr == MAP_FAILED)
@@ -305,20 +321,24 @@ static void *get_pages(unsigned int num)
 	return addr;
 }
 
-/* This routine is used to load the kernel or initrd.  It tries mmap, but if
+/*
+ * This routine is used to load the kernel or initrd.  It tries mmap, but if
  * that fails (Plan 9's kernel file isn't nicely aligned on page boundaries),
- * it falls back to reading the memory in. */
+ * it falls back to reading the memory in.
+ */
 static void map_at(int fd, void *addr, unsigned long offset, unsigned long len)
 {
 	ssize_t r;
 
-	/* We map writable even though for some segments are marked read-only.
+	/*
+	 * We map writable even though for some segments are marked read-only.
 	 * The kernel really wants to be writable: it patches its own
 	 * instructions.
 	 *
 	 * MAP_PRIVATE means that the page won't be copied until a write is
 	 * done to it.  This allows us to share untouched memory between
-	 * Guests. */
+	 * Guests.
+	 */
 	if (mmap(addr, len, PROT_READ|PROT_WRITE|PROT_EXEC,
 		 MAP_FIXED|MAP_PRIVATE, fd, offset) != MAP_FAILED)
 		return;
@@ -329,7 +349,8 @@ static void map_at(int fd, void *addr, unsigned long offset, unsigned long len)
 		err(1, "Reading offset %lu len %lu gave %zi", offset, len, r);
 }
 
-/* This routine takes an open vmlinux image, which is in ELF, and maps it into
+/*
+ * This routine takes an open vmlinux image, which is in ELF, and maps it into
  * the Guest memory.  ELF = Embedded Linking Format, which is the format used
  * by all modern binaries on Linux including the kernel.
  *
@@ -337,23 +358,28 @@ static void map_at(int fd, void *addr, unsigned long offset, unsigned long len)
  * address.  We use the physical address; the Guest will map itself to the
  * virtual address.
  *
- * We return the starting address. */
+ * We return the starting address.
+ */
 static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr)
 {
 	Elf32_Phdr phdr[ehdr->e_phnum];
 	unsigned int i;
 
-	/* Sanity checks on the main ELF header: an x86 executable with a
-	 * reasonable number of correctly-sized program headers. */
+	/*
+	 * Sanity checks on the main ELF header: an x86 executable with a
+	 * reasonable number of correctly-sized program headers.
+	 */
 	if (ehdr->e_type != ET_EXEC
 	    || ehdr->e_machine != EM_386
 	    || ehdr->e_phentsize != sizeof(Elf32_Phdr)
 	    || ehdr->e_phnum < 1 || ehdr->e_phnum > 65536U/sizeof(Elf32_Phdr))
 		errx(1, "Malformed elf header");
 
-	/* An ELF executable contains an ELF header and a number of "program"
+	/*
+	 * An ELF executable contains an ELF header and a number of "program"
 	 * headers which indicate which parts ("segments") of the program to
-	 * load where. */
+	 * load where.
+	 */
 
 	/* We read in all the program headers at once: */
 	if (lseek(elf_fd, ehdr->e_phoff, SEEK_SET) < 0)
@@ -361,8 +387,10 @@ static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr)
 	if (read(elf_fd, phdr, sizeof(phdr)) != sizeof(phdr))
 		err(1, "Reading program headers");
 
-	/* Try all the headers: there are usually only three.  A read-only one,
-	 * a read-write one, and a "note" section which we don't load. */
+	/*
+	 * Try all the headers: there are usually only three.  A read-only one,
+	 * a read-write one, and a "note" section which we don't load.
+	 */
 	for (i = 0; i < ehdr->e_phnum; i++) {
 		/* If this isn't a loadable segment, we ignore it */
 		if (phdr[i].p_type != PT_LOAD)
@@ -380,13 +408,15 @@ static unsigned long map_elf(int elf_fd, const Elf32_Ehdr *ehdr)
 	return ehdr->e_entry;
 }
 
-/*L:150 A bzImage, unlike an ELF file, is not meant to be loaded.  You're
- * supposed to jump into it and it will unpack itself.  We used to have to
- * perform some hairy magic because the unpacking code scared me.
+/*L:150
+ * A bzImage, unlike an ELF file, is not meant to be loaded.  You're supposed
+ * to jump into it and it will unpack itself.  We used to have to perform some
+ * hairy magic because the unpacking code scared me.
  *
  * Fortunately, Jeremy Fitzhardinge convinced me it wasn't that hard and wrote
  * a small patch to jump over the tricky bits in the Guest, so now we just read
- * the funky header so we know where in the file to load, and away we go! */
+ * the funky header so we know where in the file to load, and away we go!
+ */
 static unsigned long load_bzimage(int fd)
 {
 	struct boot_params boot;
@@ -394,8 +424,10 @@ static unsigned long load_bzimage(int fd)
 	/* Modern bzImages get loaded at 1M. */
 	void *p = from_guest_phys(0x100000);
 
-	/* Go back to the start of the file and read the header.  It should be
-	 * a Linux boot header (see Documentation/x86/i386/boot.txt) */
+	/*
+	 * Go back to the start of the file and read the header.  It should be
+	 * a Linux boot header (see Documentation/x86/i386/boot.txt)
+	 */
 	lseek(fd, 0, SEEK_SET);
 	read(fd, &boot, sizeof(boot));
 
@@ -414,9 +446,11 @@ static unsigned long load_bzimage(int fd)
 	return boot.hdr.code32_start;
 }
 
-/*L:140 Loading the kernel is easy when it's a "vmlinux", but most kernels
+/*L:140
+ * Loading the kernel is easy when it's a "vmlinux", but most kernels
  * come wrapped up in the self-decompressing "bzImage" format.  With a little
- * work, we can load those, too. */
+ * work, we can load those, too.
+ */
 static unsigned long load_kernel(int fd)
 {
 	Elf32_Ehdr hdr;
@@ -433,24 +467,28 @@ static unsigned long load_kernel(int fd)
 	return load_bzimage(fd);
 }
 
-/* This is a trivial little helper to align pages.  Andi Kleen hated it because
+/*
+ * This is a trivial little helper to align pages.  Andi Kleen hated it because
  * it calls getpagesize() twice: "it's dumb code."
  *
  * Kernel guys get really het up about optimization, even when it's not
- * necessary.  I leave this code as a reaction against that. */
+ * necessary.  I leave this code as a reaction against that.
+ */
 static inline unsigned long page_align(unsigned long addr)
 {
 	/* Add upwards and truncate downwards. */
 	return ((addr + getpagesize()-1) & ~(getpagesize()-1));
 }
 
-/*L:180 An "initial ram disk" is a disk image loaded into memory along with
- * the kernel which the kernel can use to boot from without needing any
- * drivers.  Most distributions now use this as standard: the initrd contains
- * the code to load the appropriate driver modules for the current machine.
+/*L:180
+ * An "initial ram disk" is a disk image loaded into memory along with the
+ * kernel which the kernel can use to boot from without needing any drivers.
+ * Most distributions now use this as standard: the initrd contains the code to
+ * load the appropriate driver modules for the current machine.
  *
  * Importantly, James Morris works for RedHat, and Fedora uses initrds for its
- * kernels.  He sent me this (and tells me when I break it). */
+ * kernels.  He sent me this (and tells me when I break it).
+ */
 static unsigned long load_initrd(const char *name, unsigned long mem)
 {
 	int ifd;
@@ -462,12 +500,16 @@ static unsigned long load_initrd(const char *name, unsigned long mem)
 	if (fstat(ifd, &st) < 0)
 		err(1, "fstat() on initrd '%s'", name);
 
-	/* We map the initrd at the top of memory, but mmap wants it to be
-	 * page-aligned, so we round the size up for that. */
+	/*
+	 * We map the initrd at the top of memory, but mmap wants it to be
+	 * page-aligned, so we round the size up for that.
+	 */
 	len = page_align(st.st_size);
 	map_at(ifd, from_guest_phys(mem - len), 0, st.st_size);
-	/* Once a file is mapped, you can close the file descriptor.  It's a
-	 * little odd, but quite useful. */
+	/*
+	 * Once a file is mapped, you can close the file descriptor.  It's a
+	 * little odd, but quite useful.
+	 */
 	close(ifd);
 	verbose("mapped initrd %s size=%lu @ %p\n", name, len, (void*)mem-len);
 
@@ -476,8 +518,10 @@ static unsigned long load_initrd(const char *name, unsigned long mem)
 }
 /*:*/
 
-/* Simple routine to roll all the commandline arguments together with spaces
- * between them. */
+/*
+ * Simple routine to roll all the commandline arguments together with spaces
+ * between them.
+ */
 static void concat(char *dst, char *args[])
 {
 	unsigned int i, len = 0;
@@ -494,10 +538,12 @@ static void concat(char *dst, char *args[])
 	dst[len] = '\0';
 }
 
-/*L:185 This is where we actually tell the kernel to initialize the Guest.  We
+/*L:185
+ * This is where we actually tell the kernel to initialize the Guest.  We
  * saw the arguments it expects when we looked at initialize() in lguest_user.c:
  * the base of Guest "physical" memory, the top physical page to allow and the
- * entry point for the Guest. */
+ * entry point for the Guest.
+ */
 static void tell_kernel(unsigned long start)
 {
 	unsigned long args[] = { LHREQ_INITIALIZE,
@@ -522,20 +568,26 @@ static void tell_kernel(unsigned long start)
 static void *_check_pointer(unsigned long addr, unsigned int size,
 			    unsigned int line)
 {
-	/* We have to separately check addr and addr+size, because size could
-	 * be huge and addr + size might wrap around. */
+	/*
+	 * We have to separately check addr and addr+size, because size could
+	 * be huge and addr + size might wrap around.
+	 */
 	if (addr >= guest_limit || addr + size >= guest_limit)
 		errx(1, "%s:%i: Invalid address %#lx", __FILE__, line, addr);
-	/* We return a pointer for the caller's convenience, now we know it's
-	 * safe to use. */
+	/*
+	 * We return a pointer for the caller's convenience, now we know it's
+	 * safe to use.
+	 */
 	return from_guest_phys(addr);
 }
 /* A macro which transparently hands the line number to the real function. */
 #define check_pointer(addr,size) _check_pointer(addr, size, __LINE__)
 
-/* Each buffer in the virtqueues is actually a chain of descriptors.  This
+/*
+ * Each buffer in the virtqueues is actually a chain of descriptors.  This
  * function returns the next descriptor in the chain, or vq->vring.num if we're
- * at the end. */
+ * at the end.
+ */
 static unsigned next_desc(struct vring_desc *desc,
 			  unsigned int i, unsigned int max)
 {
@@ -576,12 +628,14 @@ static void trigger_irq(struct virtqueue *vq)
 		err(1, "Triggering irq %i", vq->config.irq);
 }
 
-/* This looks in the virtqueue and for the first available buffer, and converts
+/*
+ * This looks in the virtqueue and for the first available buffer, and converts
  * it to an iovec for convenient access.  Since descriptors consist of some
  * number of output then some number of input descriptors, it's actually two
  * iovecs, but we pack them into one and note how many of each there were.
  *
- * This function returns the descriptor number found. */
+ * This function returns the descriptor number found.
+ */
 static unsigned wait_for_vq_desc(struct virtqueue *vq,
 				 struct iovec iov[],
 				 unsigned int *out_num, unsigned int *in_num)
@@ -599,8 +653,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 		/* OK, now we need to know about added descriptors. */
 		vq->vring.used->flags &= ~VRING_USED_F_NO_NOTIFY;
 
-		/* They could have slipped one in as we were doing that: make
-		 * sure it's written, then check again. */
+		/*
+		 * They could have slipped one in as we were doing that: make
+		 * sure it's written, then check again.
+		 */
 		mb();
 		if (last_avail != vq->vring.avail->idx) {
 			vq->vring.used->flags |= VRING_USED_F_NO_NOTIFY;
@@ -620,8 +676,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 		errx(1, "Guest moved used index from %u to %u",
 		     last_avail, vq->vring.avail->idx);
 
-	/* Grab the next descriptor number they're advertising, and increment
-	 * the index we've seen. */
+	/*
+	 * Grab the next descriptor number they're advertising, and increment
+	 * the index we've seen.
+	 */
 	head = vq->vring.avail->ring[last_avail % vq->vring.num];
 	lg_last_avail(vq)++;
 
@@ -636,8 +694,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 	desc = vq->vring.desc;
 	i = head;
 
-	/* If this is an indirect entry, then this buffer contains a descriptor
-	 * table which we handle as if it's any normal descriptor chain. */
+	/*
+	 * If this is an indirect entry, then this buffer contains a descriptor
+	 * table which we handle as if it's any normal descriptor chain.
+	 */
 	if (desc[i].flags & VRING_DESC_F_INDIRECT) {
 		if (desc[i].len % sizeof(struct vring_desc))
 			errx(1, "Invalid size for indirect buffer table");
@@ -656,8 +716,10 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 		if (desc[i].flags & VRING_DESC_F_WRITE)
 			(*in_num)++;
 		else {
-			/* If it's an output descriptor, they're all supposed
-			 * to come before any input descriptors. */
+			/*
+			 * If it's an output descriptor, they're all supposed
+			 * to come before any input descriptors.
+			 */
 			if (*in_num)
 				errx(1, "Descriptor has out after in");
 			(*out_num)++;
@@ -671,14 +733,18 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 	return head;
 }
 
-/* After we've used one of their buffers, we tell them about it.  We'll then
- * want to send them an interrupt, using trigger_irq(). */
+/*
+ * After we've used one of their buffers, we tell them about it.  We'll then
+ * want to send them an interrupt, using trigger_irq().
+ */
 static void add_used(struct virtqueue *vq, unsigned int head, int len)
 {
 	struct vring_used_elem *used;
 
-	/* The virtqueue contains a ring of used buffers.  Get a pointer to the
-	 * next entry in that used ring. */
+	/*
+	 * The virtqueue contains a ring of used buffers.  Get a pointer to the
+	 * next entry in that used ring.
+	 */
 	used = &vq->vring.used->ring[vq->vring.used->idx % vq->vring.num];
 	used->id = head;
 	used->len = len;
@@ -698,7 +764,8 @@ static void add_used_and_trigger(struct virtqueue *vq, unsigned head, int len)
 /*
  * The Console
  *
- * We associate some data with the console for our exit hack. */
+ * We associate some data with the console for our exit hack.
+ */
 struct console_abort
 {
 	/* How many times have they hit ^C? */
@@ -725,20 +792,24 @@ static void console_input(struct virtqueue *vq)
 	if (len <= 0) {
 		/* Ran out of input? */
 		warnx("Failed to get console input, ignoring console.");
-		/* For simplicity, dying threads kill the whole Launcher.  So
-		 * just nap here. */
+		/*
+		 * For simplicity, dying threads kill the whole Launcher.  So
+		 * just nap here.
+		 */
 		for (;;)
 			pause();
 	}
 
 	add_used_and_trigger(vq, head, len);
 
-	/* Three ^C within one second?  Exit.
+	/*
+	 * Three ^C within one second?  Exit.
 	 *
 	 * This is such a hack, but works surprisingly well.  Each ^C has to
 	 * be in a buffer by itself, so they can't be too fast.  But we check
 	 * that we get three within about a second, so they can't be too
-	 * slow. */
+	 * slow.
+	 */
 	if (len != 1 || ((char *)iov[0].iov_base)[0] != 3) {
 		abort->count = 0;
 		return;
@@ -809,8 +880,7 @@ static bool will_block(int fd)
 	return select(fd+1, &fdset, NULL, NULL, &zero) != 1;
 }
 
-/* This is where we handle packets coming in from the tun device to our
- * Guest. */
+/* This handles packets coming in from the tun device to our Guest. */
 static void net_input(struct virtqueue *vq)
 {
 	int len;
@@ -842,8 +912,10 @@ static int do_thread(void *_vq)
 	return 0;
 }
 
-/* When a child dies, we kill our entire process group with SIGTERM.  This
- * also has the side effect that the shell restores the console for us! */
+/*
+ * When a child dies, we kill our entire process group with SIGTERM.  This
+ * also has the side effect that the shell restores the console for us!
+ */
 static void kill_launcher(int signal)
 {
 	kill(0, SIGTERM);
@@ -880,9 +952,10 @@ static void reset_device(struct device *dev)
 
 static void create_thread(struct virtqueue *vq)
 {
-	/* Create stack for thread and run it.  Since stack grows
-	 * upwards, we point the stack pointer to the end of this
-	 * region. */
+	/*
+	 * Create stack for thread and run it.  Since the stack grows upwards,
+	 * we point the stack pointer to the end of this region.
+	 */
 	char *stack = malloc(32768);
 	unsigned long args[] = { LHREQ_EVENTFD,
 				 vq->config.pfn*getpagesize(), 0 };
@@ -981,8 +1054,11 @@ static void handle_output(unsigned long addr)
 		}
 	}
 
-	/* Early console write is done using notify on a nul-terminated string
-	 * in Guest memory. */
+	/*
+	 * Early console write is done using notify on a nul-terminated string
+	 * in Guest memory.  It's also great for hacking debugging messages
+	 * into a Guest.
+	 */
 	if (addr >= guest_limit)
 		errx(1, "Bad NOTIFY %#lx", addr);
 
@@ -998,10 +1074,12 @@ static void handle_output(unsigned long addr)
  * routines to allocate and manage them.
  */
 
-/* The layout of the device page is a "struct lguest_device_desc" followed by a
+/*
+ * The layout of the device page is a "struct lguest_device_desc" followed by a
  * number of virtqueue descriptors, then two sets of feature bits, then an
  * array of configuration bytes.  This routine returns the configuration
- * pointer. */
+ * pointer.
+ */
 static u8 *device_config(const struct device *dev)
 {
 	return (void *)(dev->desc + 1)
@@ -1009,9 +1087,11 @@ static u8 *device_config(const struct device *dev)
 		+ dev->feature_len * 2;
 }
 
-/* This routine allocates a new "struct lguest_device_desc" from descriptor
+/*
+ * This routine allocates a new "struct lguest_device_desc" from descriptor
  * table page just above the Guest's normal memory.  It returns a pointer to
- * that descriptor. */
+ * that descriptor.
+ */
 static struct lguest_device_desc *new_dev_desc(u16 type)
 {
 	struct lguest_device_desc d = { .type = type };
@@ -1032,8 +1112,10 @@ static struct lguest_device_desc *new_dev_desc(u16 type)
 	return memcpy(p, &d, sizeof(d));
 }
 
-/* Each device descriptor is followed by the description of its virtqueues.  We
- * specify how many descriptors the virtqueue is to have. */
+/*
+ * Each device descriptor is followed by the description of its virtqueues.  We
+ * specify how many descriptors the virtqueue is to have.
+ */
 static void add_virtqueue(struct device *dev, unsigned int num_descs,
 			  void (*service)(struct virtqueue *))
 {
@@ -1061,10 +1143,12 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs,
 	/* Initialize the vring. */
 	vring_init(&vq->vring, num_descs, p, LGUEST_VRING_ALIGN);
 
-	/* Append virtqueue to this device's descriptor.  We use
+	/*
+	 * Append virtqueue to this device's descriptor.  We use
 	 * device_config() to get the end of the device's current virtqueues;
 	 * we check that we haven't added any config or feature information
-	 * yet, otherwise we'd be overwriting them. */
+	 * yet, otherwise we'd be overwriting them.
+	 */
 	assert(dev->desc->config_len == 0 && dev->desc->feature_len == 0);
 	memcpy(device_config(dev), &vq->config, sizeof(vq->config));
 	dev->num_vq++;
@@ -1072,14 +1156,18 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs,
 
 	verbose("Virtqueue page %#lx\n", to_guest_phys(p));
 
-	/* Add to tail of list, so dev->vq is first vq, dev->vq->next is
-	 * second.  */
+	/*
+	 * Add to tail of list, so dev->vq is first vq, dev->vq->next is
+	 * second.
+	 */
 	for (i = &dev->vq; *i; i = &(*i)->next);
 	*i = vq;
 }
 
-/* The first half of the feature bitmask is for us to advertise features.  The
- * second half is for the Guest to accept features. */
+/*
+ * The first half of the feature bitmask is for us to advertise features.  The
+ * second half is for the Guest to accept features.
+ */
 static void add_feature(struct device *dev, unsigned bit)
 {
 	u8 *features = get_feature_bits(dev);
@@ -1093,9 +1181,11 @@ static void add_feature(struct device *dev, unsigned bit)
 	features[bit / CHAR_BIT] |= (1 << (bit % CHAR_BIT));
 }
 
-/* This routine sets the configuration fields for an existing device's
+/*
+ * This routine sets the configuration fields for an existing device's
  * descriptor.  It only works for the last device, but that's OK because that's
- * how we use it. */
+ * how we use it.
+ */
 static void set_config(struct device *dev, unsigned len, const void *conf)
 {
 	/* Check we haven't overflowed our single page. */
@@ -1110,10 +1200,12 @@ static void set_config(struct device *dev, unsigned len, const void *conf)
 	assert(dev->desc->config_len == len);
 }
 
-/* This routine does all the creation and setup of a new device, including
+/*
+ * This routine does all the creation and setup of a new device, including
  * calling new_dev_desc() to allocate the descriptor and device memory.
  *
- * See what I mean about userspace being boring? */
+ * See what I mean about userspace being boring?
+ */
 static struct device *new_device(const char *name, u16 type)
 {
 	struct device *dev = malloc(sizeof(*dev));
@@ -1126,10 +1218,12 @@ static struct device *new_device(const char *name, u16 type)
 	dev->num_vq = 0;
 	dev->running = false;
 
-	/* Append to device list.  Prepending to a single-linked list is
+	/*
+	 * Append to device list.  Prepending to a single-linked list is
 	 * easier, but the user expects the devices to be arranged on the bus
 	 * in command-line order.  The first network device on the command line
-	 * is eth0, the first block device /dev/vda, etc. */
+	 * is eth0, the first block device /dev/vda, etc.
+	 */
 	if (devices.lastdev)
 		devices.lastdev->next = dev;
 	else
@@ -1139,8 +1233,10 @@ static struct device *new_device(const char *name, u16 type)
 	return dev;
 }
 
-/* Our first setup routine is the console.  It's a fairly simple device, but
- * UNIX tty handling makes it uglier than it could be. */
+/*
+ * Our first setup routine is the console.  It's a fairly simple device, but
+ * UNIX tty handling makes it uglier than it could be.
+ */
 static void setup_console(void)
 {
 	struct device *dev;
@@ -1148,8 +1244,10 @@ static void setup_console(void)
 	/* If we can save the initial standard input settings... */
 	if (tcgetattr(STDIN_FILENO, &orig_term) == 0) {
 		struct termios term = orig_term;
-		/* Then we turn off echo, line buffering and ^C etc.  We want a
-		 * raw input stream to the Guest. */
+		/*
+		 * Then we turn off echo, line buffering and ^C etc: We want a
+		 * raw input stream to the Guest.
+		 */
 		term.c_lflag &= ~(ISIG|ICANON|ECHO);
 		tcsetattr(STDIN_FILENO, TCSANOW, &term);
 	}
@@ -1160,10 +1258,12 @@ static void setup_console(void)
 	dev->priv = malloc(sizeof(struct console_abort));
 	((struct console_abort *)dev->priv)->count = 0;
 
-	/* The console needs two virtqueues: the input then the output.  When
+	/*
+	 * The console needs two virtqueues: the input then the output.  When
 	 * they put something the input queue, we make sure we're listening to
 	 * stdin.  When they put something in the output queue, we write it to
-	 * stdout. */
+	 * stdout.
+	 */
 	add_virtqueue(dev, VIRTQUEUE_NUM, console_input);
 	add_virtqueue(dev, VIRTQUEUE_NUM, console_output);
 
@@ -1171,7 +1271,8 @@ static void setup_console(void)
 }
 /*:*/
 
-/*M:010 Inter-guest networking is an interesting area.  Simplest is to have a
+/*M:010
+ * Inter-guest networking is an interesting area.  Simplest is to have a
  * --sharenet=<name> option which opens or creates a named pipe.  This can be
  * used to send packets to another guest in a 1:1 manner.
  *
@@ -1185,7 +1286,8 @@ static void setup_console(void)
  * multiple inter-guest channels behind one interface, although it would
  * require some manner of hotplugging new virtio channels.
  *
- * Finally, we could implement a virtio network switch in the kernel. :*/
+ * Finally, we could implement a virtio network switch in the kernel.
+:*/
 
 static u32 str2ip(const char *ipaddr)
 {
@@ -1210,11 +1312,13 @@ static void str2mac(const char *macaddr, unsigned char mac[6])
 	mac[5] = m[5];
 }
 
-/* This code is "adapted" from libbridge: it attaches the Host end of the
+/*
+ * This code is "adapted" from libbridge: it attaches the Host end of the
  * network device to the bridge device specified by the command line.
  *
  * This is yet another James Morris contribution (I'm an IP-level guy, so I
- * dislike bridging), and I just try not to break it. */
+ * dislike bridging), and I just try not to break it.
+ */
 static void add_to_bridge(int fd, const char *if_name, const char *br_name)
 {
 	int ifidx;
@@ -1234,9 +1338,11 @@ static void add_to_bridge(int fd, const char *if_name, const char *br_name)
 		err(1, "can't add %s to bridge %s", if_name, br_name);
 }
 
-/* This sets up the Host end of the network device with an IP address, brings
+/*
+ * This sets up the Host end of the network device with an IP address, brings
  * it up so packets will flow, the copies the MAC address into the hwaddr
- * pointer. */
+ * pointer.
+ */
 static void configure_device(int fd, const char *tapif, u32 ipaddr)
 {
 	struct ifreq ifr;
@@ -1263,10 +1369,12 @@ static int get_tun_device(char tapif[IFNAMSIZ])
 	/* Start with this zeroed.  Messy but sure. */
 	memset(&ifr, 0, sizeof(ifr));
 
-	/* We open the /dev/net/tun device and tell it we want a tap device.  A
+	/*
+	 * We open the /dev/net/tun device and tell it we want a tap device.  A
 	 * tap device is like a tun device, only somehow different.  To tell
 	 * the truth, I completely blundered my way through this code, but it
-	 * works now! */
+	 * works now!
+	 */
 	netfd = open_or_die("/dev/net/tun", O_RDWR);
 	ifr.ifr_flags = IFF_TAP | IFF_NO_PI | IFF_VNET_HDR;
 	strcpy(ifr.ifr_name, "tap%d");
@@ -1277,18 +1385,22 @@ static int get_tun_device(char tapif[IFNAMSIZ])
 		  TUN_F_CSUM|TUN_F_TSO4|TUN_F_TSO6|TUN_F_TSO_ECN) != 0)
 		err(1, "Could not set features for tun device");
 
-	/* We don't need checksums calculated for packets coming in this
-	 * device: trust us! */
+	/*
+	 * We don't need checksums calculated for packets coming in this
+	 * device: trust us!
+	 */
 	ioctl(netfd, TUNSETNOCSUM, 1);
 
 	memcpy(tapif, ifr.ifr_name, IFNAMSIZ);
 	return netfd;
 }
 
-/*L:195 Our network is a Host<->Guest network.  This can either use bridging or
+/*L:195
+ * Our network is a Host<->Guest network.  This can either use bridging or
  * routing, but the principle is the same: it uses the "tun" device to inject
  * packets into the Host as if they came in from a normal network card.  We
- * just shunt packets between the Guest and the tun device. */
+ * just shunt packets between the Guest and the tun device.
+ */
 static void setup_tun_net(char *arg)
 {
 	struct device *dev;
@@ -1305,13 +1417,14 @@ static void setup_tun_net(char *arg)
 	dev = new_device("net", VIRTIO_ID_NET);
 	dev->priv = net_info;
 
-	/* Network devices need a receive and a send queue, just like
-	 * console. */
+	/* Network devices need a recv and a send queue, just like console. */
 	add_virtqueue(dev, VIRTQUEUE_NUM, net_input);
 	add_virtqueue(dev, VIRTQUEUE_NUM, net_output);
 
-	/* We need a socket to perform the magic network ioctls to bring up the
-	 * tap interface, connect to the bridge etc.  Any socket will do! */
+	/*
+	 * We need a socket to perform the magic network ioctls to bring up the
+	 * tap interface, connect to the bridge etc.  Any socket will do!
+	 */
 	ipfd = socket(PF_INET, SOCK_DGRAM, IPPROTO_IP);
 	if (ipfd < 0)
 		err(1, "opening IP socket");
@@ -1366,7 +1479,8 @@ static void setup_tun_net(char *arg)
 			devices.device_num, tapif, arg);
 }
 
-/* Our block (disk) device should be really simple: the Guest asks for a block
+/*
+ * Our block (disk) device should be really simple: the Guest asks for a block
  * number and we read or write that position in the file.  Unfortunately, that
  * was amazingly slow: the Guest waits until the read is finished before
  * running anything else, even if it could have been doing useful work.
@@ -1374,7 +1488,9 @@ static void setup_tun_net(char *arg)
  * We could use async I/O, except it's reputed to suck so hard that characters
  * actually go missing from your code when you try to use it.
  *
- * So we farm the I/O out to thread, and communicate with it via a pipe. */
+ * So this was one reason why lguest now does all virtqueue servicing in
+ * separate threads: it's more efficient and more like a real device.
+ */
 
 /* This hangs off device->priv. */
 struct vblk_info
@@ -1412,9 +1528,11 @@ static void blk_request(struct virtqueue *vq)
 	/* Get the next request. */
 	head = wait_for_vq_desc(vq, iov, &out_num, &in_num);
 
-	/* Every block request should contain at least one output buffer
+	/*
+	 * Every block request should contain at least one output buffer
 	 * (detailing the location on disk and the type of request) and one
-	 * input buffer (to hold the result). */
+	 * input buffer (to hold the result).
+	 */
 	if (out_num == 0 || in_num == 0)
 		errx(1, "Bad virtblk cmd %u out=%u in=%u",
 		     head, out_num, in_num);
@@ -1423,33 +1541,41 @@ static void blk_request(struct virtqueue *vq)
 	in = convert(&iov[out_num+in_num-1], u8);
 	off = out->sector * 512;
 
-	/* The block device implements "barriers", where the Guest indicates
+	/*
+	 * The block device implements "barriers", where the Guest indicates
 	 * that it wants all previous writes to occur before this write.  We
 	 * don't have a way of asking our kernel to do a barrier, so we just
-	 * synchronize all the data in the file.  Pretty poor, no? */
+	 * synchronize all the data in the file.  Pretty poor, no?
+	 */
 	if (out->type & VIRTIO_BLK_T_BARRIER)
 		fdatasync(vblk->fd);
 
-	/* In general the virtio block driver is allowed to try SCSI commands.
-	 * It'd be nice if we supported eject, for example, but we don't. */
+	/*
+	 * In general the virtio block driver is allowed to try SCSI commands.
+	 * It'd be nice if we supported eject, for example, but we don't.
+	 */
 	if (out->type & VIRTIO_BLK_T_SCSI_CMD) {
 		fprintf(stderr, "Scsi commands unsupported\n");
 		*in = VIRTIO_BLK_S_UNSUPP;
 		wlen = sizeof(*in);
 	} else if (out->type & VIRTIO_BLK_T_OUT) {
-		/* Write */
-
-		/* Move to the right location in the block file.  This can fail
-		 * if they try to write past end. */
+		/*
+		 * Write
+		 *
+		 * Move to the right location in the block file.  This can fail
+		 * if they try to write past end.
+		 */
 		if (lseek64(vblk->fd, off, SEEK_SET) != off)
 			err(1, "Bad seek to sector %llu", out->sector);
 
 		ret = writev(vblk->fd, iov+1, out_num-1);
 		verbose("WRITE to sector %llu: %i\n", out->sector, ret);
 
-		/* Grr... Now we know how long the descriptor they sent was, we
+		/*
+		 * Grr... Now we know how long the descriptor they sent was, we
 		 * make sure they didn't try to write over the end of the block
-		 * file (possibly extending it). */
+		 * file (possibly extending it).
+		 */
 		if (ret > 0 && off + ret > vblk->len) {
 			/* Trim it back to the correct length */
 			ftruncate64(vblk->fd, vblk->len);
@@ -1459,10 +1585,12 @@ static void blk_request(struct virtqueue *vq)
 		wlen = sizeof(*in);
 		*in = (ret >= 0 ? VIRTIO_BLK_S_OK : VIRTIO_BLK_S_IOERR);
 	} else {
-		/* Read */
-
-		/* Move to the right location in the block file.  This can fail
-		 * if they try to read past end. */
+		/*
+		 * Read
+		 *
+		 * Move to the right location in the block file.  This can fail
+		 * if they try to read past end.
+		 */
 		if (lseek64(vblk->fd, off, SEEK_SET) != off)
 			err(1, "Bad seek to sector %llu", out->sector);
 
@@ -1477,10 +1605,12 @@ static void blk_request(struct virtqueue *vq)
 		}
 	}
 
-	/* OK, so we noted that it was pretty poor to use an fdatasync as a
+	/*
+	 * OK, so we noted that it was pretty poor to use an fdatasync as a
 	 * barrier.  But Christoph Hellwig points out that we need a sync
 	 * *afterwards* as well: "Barriers specify no reordering to the front
-	 * or the back."  And Jens Axboe confirmed it, so here we are: */
+	 * or the back."  And Jens Axboe confirmed it, so here we are:
+	 */
 	if (out->type & VIRTIO_BLK_T_BARRIER)
 		fdatasync(vblk->fd);
 
@@ -1494,7 +1624,7 @@ static void setup_block_file(const char *filename)
 	struct vblk_info *vblk;
 	struct virtio_blk_config conf;
 
-	/* The device responds to return from I/O thread. */
+	/* Creat the device. */
 	dev = new_device("block", VIRTIO_ID_BLOCK);
 
 	/* The device has one virtqueue, where the Guest places requests. */
@@ -1513,8 +1643,10 @@ static void setup_block_file(const char *filename)
 	/* Tell Guest how many sectors this device has. */
 	conf.capacity = cpu_to_le64(vblk->len / 512);
 
-	/* Tell Guest not to put in too many descriptors at once: two are used
-	 * for the in and out elements. */
+	/*
+	 * Tell Guest not to put in too many descriptors at once: two are used
+	 * for the in and out elements.
+	 */
 	add_feature(dev, VIRTIO_BLK_F_SEG_MAX);
 	conf.seg_max = cpu_to_le32(VIRTQUEUE_NUM - 2);
 
@@ -1525,16 +1657,18 @@ static void setup_block_file(const char *filename)
 		++devices.device_num, le64_to_cpu(conf.capacity));
 }
 
-struct rng_info {
-	int rfd;
-};
-
-/* Our random number generator device reads from /dev/random into the Guest's
+/*L:211
+ * Our random number generator device reads from /dev/random into the Guest's
  * input buffers.  The usual case is that the Guest doesn't want random numbers
  * and so has no buffers although /dev/random is still readable, whereas
  * console is the reverse.
  *
- * The same logic applies, however. */
+ * The same logic applies, however.
+ */
+struct rng_info {
+	int rfd;
+};
+
 static void rng_input(struct virtqueue *vq)
 {
 	int len;
@@ -1547,9 +1681,11 @@ static void rng_input(struct virtqueue *vq)
 	if (out_num)
 		errx(1, "Output buffers in rng?");
 
-	/* This is why we convert to iovecs: the readv() call uses them, and so
+	/*
+	 * This is why we convert to iovecs: the readv() call uses them, and so
 	 * it reads straight into the Guest's buffer.  We loop to make sure we
-	 * fill it. */
+	 * fill it.
+	 */
 	while (!iov_empty(iov, in_num)) {
 		len = readv(rng_info->rfd, iov, in_num);
 		if (len <= 0)
@@ -1562,15 +1698,18 @@ static void rng_input(struct virtqueue *vq)
 	add_used(vq, head, totlen);
 }
 
-/* And this creates a "hardware" random number device for the Guest. */
+/*L:199
+ * This creates a "hardware" random number device for the Guest.
+ */
 static void setup_rng(void)
 {
 	struct device *dev;
 	struct rng_info *rng_info = malloc(sizeof(*rng_info));
 
+	/* Our device's privat info simply contains the /dev/random fd. */
 	rng_info->rfd = open_or_die("/dev/random", O_RDONLY);
 
-	/* The device responds to return from I/O thread. */
+	/* Create the new device. */
 	dev = new_device("rng", VIRTIO_ID_RNG);
 	dev->priv = rng_info;
 
@@ -1586,8 +1725,10 @@ static void __attribute__((noreturn)) restart_guest(void)
 {
 	unsigned int i;
 
-	/* Since we don't track all open fds, we simply close everything beyond
-	 * stderr. */
+	/*
+	 * Since we don't track all open fds, we simply close everything beyond
+	 * stderr.
+	 */
 	for (i = 3; i < FD_SETSIZE; i++)
 		close(i);
 
@@ -1598,8 +1739,10 @@ static void __attribute__((noreturn)) restart_guest(void)
 	err(1, "Could not exec %s", main_args[0]);
 }
 
-/*L:220 Finally we reach the core of the Launcher which runs the Guest, serves
- * its input and output, and finally, lays it to rest. */
+/*L:220
+ * Finally we reach the core of the Launcher which runs the Guest, serves
+ * its input and output, and finally, lays it to rest.
+ */
 static void __attribute__((noreturn)) run_guest(void)
 {
 	for (;;) {
@@ -1634,7 +1777,7 @@ static void __attribute__((noreturn)) run_guest(void)
  *
  * Are you ready?  Take a deep breath and join me in the core of the Host, in
  * "make Host".
- :*/
+:*/
 
 static struct option opts[] = {
 	{ "verbose", 0, NULL, 'v' },
@@ -1655,8 +1798,7 @@ static void usage(void)
 /*L:105 The main routine is where the real work begins: */
 int main(int argc, char *argv[])
 {
-	/* Memory, top-level pagetable, code startpoint and size of the
-	 * (optional) initrd. */
+	/* Memory, code startpoint and size of the (optional) initrd. */
 	unsigned long mem = 0, start, initrd_size = 0;
 	/* Two temporaries. */
 	int i, c;
@@ -1668,24 +1810,30 @@ int main(int argc, char *argv[])
 	/* Save the args: we "reboot" by execing ourselves again. */
 	main_args = argv;
 
-	/* First we initialize the device list.  We keep a pointer to the last
+	/*
+	 * First we initialize the device list.  We keep a pointer to the last
 	 * device, and the next interrupt number to use for devices (1:
-	 * remember that 0 is used by the timer). */
+	 * remember that 0 is used by the timer).
+	 */
 	devices.lastdev = NULL;
 	devices.next_irq = 1;
 
 	cpu_id = 0;
-	/* We need to know how much memory so we can set up the device
+	/*
+	 * We need to know how much memory so we can set up the device
 	 * descriptor and memory pages for the devices as we parse the command
 	 * line.  So we quickly look through the arguments to find the amount
-	 * of memory now. */
+	 * of memory now.
+	 */
 	for (i = 1; i < argc; i++) {
 		if (argv[i][0] != '-') {
 			mem = atoi(argv[i]) * 1024 * 1024;
-			/* We start by mapping anonymous pages over all of
+			/*
+			 * We start by mapping anonymous pages over all of
 			 * guest-physical memory range.  This fills it with 0,
 			 * and ensures that the Guest won't be killed when it
-			 * tries to access it. */
+			 * tries to access it.
+			 */
 			guest_base = map_zeroed_pages(mem / getpagesize()
 						      + DEVICE_PAGES);
 			guest_limit = mem;
@@ -1718,8 +1866,10 @@ int main(int argc, char *argv[])
 			usage();
 		}
 	}
-	/* After the other arguments we expect memory and kernel image name,
-	 * followed by command line arguments for the kernel. */
+	/*
+	 * After the other arguments we expect memory and kernel image name,
+	 * followed by command line arguments for the kernel.
+	 */
 	if (optind + 2 > argc)
 		usage();
 
@@ -1737,20 +1887,26 @@ int main(int argc, char *argv[])
 	/* Map the initrd image if requested (at top of physical memory) */
 	if (initrd_name) {
 		initrd_size = load_initrd(initrd_name, mem);
-		/* These are the location in the Linux boot header where the
-		 * start and size of the initrd are expected to be found. */
+		/*
+		 * These are the location in the Linux boot header where the
+		 * start and size of the initrd are expected to be found.
+		 */
 		boot->hdr.ramdisk_image = mem - initrd_size;
 		boot->hdr.ramdisk_size = initrd_size;
 		/* The bootloader type 0xFF means "unknown"; that's OK. */
 		boot->hdr.type_of_loader = 0xFF;
 	}
 
-	/* The Linux boot header contains an "E820" memory map: ours is a
-	 * simple, single region. */
+	/*
+	 * The Linux boot header contains an "E820" memory map: ours is a
+	 * simple, single region.
+	 */
 	boot->e820_entries = 1;
 	boot->e820_map[0] = ((struct e820entry) { 0, mem, E820_RAM });
-	/* The boot header contains a command line pointer: we put the command
-	 * line after the boot header. */
+	/*
+	 * The boot header contains a command line pointer: we put the command
+	 * line after the boot header.
+	 */
 	boot->hdr.cmd_line_ptr = to_guest_phys(boot + 1);
 	/* We use a simple helper to copy the arguments separated by spaces. */
 	concat((char *)(boot + 1), argv+optind+2);
@@ -1764,8 +1920,10 @@ int main(int argc, char *argv[])
 	/* Tell the entry path not to try to reload segment registers. */
 	boot->hdr.loadflags |= KEEP_SEGMENTS;
 
-	/* We tell the kernel to initialize the Guest: this returns the open
-	 * /dev/lguest file descriptor. */
+	/*
+	 * We tell the kernel to initialize the Guest: this returns the open
+	 * /dev/lguest file descriptor.
+	 */
 	tell_kernel(start);
 
 	/* Ensure that we terminate if a child dies. */
diff --git a/arch/x86/include/asm/lguest.h b/arch/x86/include/asm/lguest.h
index 313389cd50d..5136dad57cb 100644
--- a/arch/x86/include/asm/lguest.h
+++ b/arch/x86/include/asm/lguest.h
@@ -17,8 +17,7 @@
 /* Pages for switcher itself, then two pages per cpu */
 #define TOTAL_SWITCHER_PAGES (SHARED_SWITCHER_PAGES + 2 * nr_cpu_ids)
 
-/* We map at -4M (-2M when PAE is activated) for ease of mapping
- * into the guest (one PTE page). */
+/* We map at -4M (-2M for PAE) for ease of mapping (one PTE page). */
 #ifdef CONFIG_X86_PAE
 #define SWITCHER_ADDR 0xFFE00000
 #else
diff --git a/arch/x86/include/asm/lguest_hcall.h b/arch/x86/include/asm/lguest_hcall.h
index 33600a66755..cceb73e12e5 100644
--- a/arch/x86/include/asm/lguest_hcall.h
+++ b/arch/x86/include/asm/lguest_hcall.h
@@ -30,7 +30,8 @@
 #include <asm/hw_irq.h>
 #include <asm/kvm_para.h>
 
-/*G:030 But first, how does our Guest contact the Host to ask for privileged
+/*G:030
+ * But first, how does our Guest contact the Host to ask for privileged
  * operations?  There are two ways: the direct way is to make a "hypercall",
  * to make requests of the Host Itself.
  *
@@ -41,16 +42,15 @@
  *
  * Grossly invalid calls result in Sudden Death at the hands of the vengeful
  * Host, rather than returning failure.  This reflects Winston Churchill's
- * definition of a gentleman: "someone who is only rude intentionally". */
-/*:*/
+ * definition of a gentleman: "someone who is only rude intentionally".
+:*/
 
 /* Can't use our min() macro here: needs to be a constant */
 #define LGUEST_IRQS (NR_IRQS < 32 ? NR_IRQS: 32)
 
 #define LHCALL_RING_SIZE 64
 struct hcall_args {
-	/* These map directly onto eax, ebx, ecx, edx and esi
-	 * in struct lguest_regs */
+	/* These map directly onto eax/ebx/ecx/edx/esi in struct lguest_regs */
 	unsigned long arg0, arg1, arg2, arg3, arg4;
 };
 
diff --git a/arch/x86/lguest/boot.c b/arch/x86/lguest/boot.c
index f2bf1f73d46..025c04d18f2 100644
--- a/arch/x86/lguest/boot.c
+++ b/arch/x86/lguest/boot.c
@@ -22,7 +22,8 @@
  *
  * So how does the kernel know it's a Guest?  We'll see that later, but let's
  * just say that we end up here where we replace the native functions various
- * "paravirt" structures with our Guest versions, then boot like normal. :*/
+ * "paravirt" structures with our Guest versions, then boot like normal.
+:*/
 
 /*
  * Copyright (C) 2006, Rusty Russell <rusty@rustcorp.com.au> IBM Corporation.
@@ -74,7 +75,8 @@
  *
  * The Guest in our tale is a simple creature: identical to the Host but
  * behaving in simplified but equivalent ways.  In particular, the Guest is the
- * same kernel as the Host (or at least, built from the same source code). :*/
+ * same kernel as the Host (or at least, built from the same source code).
+:*/
 
 struct lguest_data lguest_data = {
 	.hcall_status = { [0 ... LHCALL_RING_SIZE-1] = 0xFF },
@@ -85,7 +87,8 @@ struct lguest_data lguest_data = {
 	.syscall_vec = SYSCALL_VECTOR,
 };
 
-/*G:037 async_hcall() is pretty simple: I'm quite proud of it really.  We have a
+/*G:037
+ * async_hcall() is pretty simple: I'm quite proud of it really.  We have a
  * ring buffer of stored hypercalls which the Host will run though next time we
  * do a normal hypercall.  Each entry in the ring has 5 slots for the hypercall
  * arguments, and a "hcall_status" word which is 0 if the call is ready to go,
@@ -94,7 +97,8 @@ struct lguest_data lguest_data = {
  * If we come around to a slot which hasn't been finished, then the table is
  * full and we just make the hypercall directly.  This has the nice side
  * effect of causing the Host to run all the stored calls in the ring buffer
- * which empties it for next time! */
+ * which empties it for next time!
+ */
 static void async_hcall(unsigned long call, unsigned long arg1,
 			unsigned long arg2, unsigned long arg3,
 			unsigned long arg4)
@@ -103,9 +107,11 @@ static void async_hcall(unsigned long call, unsigned long arg1,
 	static unsigned int next_call;
 	unsigned long flags;
 
-	/* Disable interrupts if not already disabled: we don't want an
+	/*
+	 * Disable interrupts if not already disabled: we don't want an
 	 * interrupt handler making a hypercall while we're already doing
-	 * one! */
+	 * one!
+	 */
 	local_irq_save(flags);
 	if (lguest_data.hcall_status[next_call] != 0xFF) {
 		/* Table full, so do normal hcall which will flush table. */
@@ -125,8 +131,9 @@ static void async_hcall(unsigned long call, unsigned long arg1,
 	local_irq_restore(flags);
 }
 
-/*G:035 Notice the lazy_hcall() above, rather than hcall().  This is our first
- * real optimization trick!
+/*G:035
+ * Notice the lazy_hcall() above, rather than hcall().  This is our first real
+ * optimization trick!
  *
  * When lazy_mode is set, it means we're allowed to defer all hypercalls and do
  * them as a batch when lazy_mode is eventually turned off.  Because hypercalls
@@ -136,7 +143,8 @@ static void async_hcall(unsigned long call, unsigned long arg1,
  * lguest_leave_lazy_mode().
  *
  * So, when we're in lazy mode, we call async_hcall() to store the call for
- * future processing: */
+ * future processing:
+ */
 static void lazy_hcall1(unsigned long call,
 		       unsigned long arg1)
 {
@@ -208,9 +216,11 @@ static void lguest_end_context_switch(struct task_struct *next)
  * check there before it tries to deliver an interrupt.
  */
 
-/* save_flags() is expected to return the processor state (ie. "flags").  The
+/*
+ * save_flags() is expected to return the processor state (ie. "flags").  The
  * flags word contains all kind of stuff, but in practice Linux only cares
- * about the interrupt flag.  Our "save_flags()" just returns that. */
+ * about the interrupt flag.  Our "save_flags()" just returns that.
+ */
 static unsigned long save_fl(void)
 {
 	return lguest_data.irq_enabled;
@@ -222,13 +232,15 @@ static void irq_disable(void)
 	lguest_data.irq_enabled = 0;
 }
 
-/* Let's pause a moment.  Remember how I said these are called so often?
+/*
+ * Let's pause a moment.  Remember how I said these are called so often?
  * Jeremy Fitzhardinge optimized them so hard early in 2009 that he had to
  * break some rules.  In particular, these functions are assumed to save their
  * own registers if they need to: normal C functions assume they can trash the
  * eax register.  To use normal C functions, we use
  * PV_CALLEE_SAVE_REGS_THUNK(), which pushes %eax onto the stack, calls the
- * C function, then restores it. */
+ * C function, then restores it.
+ */
 PV_CALLEE_SAVE_REGS_THUNK(save_fl);
 PV_CALLEE_SAVE_REGS_THUNK(irq_disable);
 /*:*/
@@ -237,18 +249,20 @@ PV_CALLEE_SAVE_REGS_THUNK(irq_disable);
 extern void lg_irq_enable(void);
 extern void lg_restore_fl(unsigned long flags);
 
-/*M:003 Note that we don't check for outstanding interrupts when we re-enable
- * them (or when we unmask an interrupt).  This seems to work for the moment,
- * since interrupts are rare and we'll just get the interrupt on the next timer
- * tick, but now we can run with CONFIG_NO_HZ, we should revisit this.  One way
- * would be to put the "irq_enabled" field in a page by itself, and have the
- * Host write-protect it when an interrupt comes in when irqs are disabled.
- * There will then be a page fault as soon as interrupts are re-enabled.
+/*M:003
+ * Note that we don't check for outstanding interrupts when we re-enable them
+ * (or when we unmask an interrupt).  This seems to work for the moment, since
+ * interrupts are rare and we'll just get the interrupt on the next timer tick,
+ * but now we can run with CONFIG_NO_HZ, we should revisit this.  One way would
+ * be to put the "irq_enabled" field in a page by itself, and have the Host
+ * write-protect it when an interrupt comes in when irqs are disabled.  There
+ * will then be a page fault as soon as interrupts are re-enabled.
  *
  * A better method is to implement soft interrupt disable generally for x86:
  * instead of disabling interrupts, we set a flag.  If an interrupt does come
  * in, we then disable them for real.  This is uncommon, so we could simply use
- * a hypercall for interrupt control and not worry about efficiency. :*/
+ * a hypercall for interrupt control and not worry about efficiency.
+:*/
 
 /*G:034
  * The Interrupt Descriptor Table (IDT).
@@ -261,10 +275,12 @@ extern void lg_restore_fl(unsigned long flags);
 static void lguest_write_idt_entry(gate_desc *dt,
 				   int entrynum, const gate_desc *g)
 {
-	/* The gate_desc structure is 8 bytes long: we hand it to the Host in
+	/*
+	 * The gate_desc structure is 8 bytes long: we hand it to the Host in
 	 * two 32-bit chunks.  The whole 32-bit kernel used to hand descriptors
 	 * around like this; typesafety wasn't a big concern in Linux's early
-	 * years. */
+	 * years.
+	 */
 	u32 *desc = (u32 *)g;
 	/* Keep the local copy up to date. */
 	native_write_idt_entry(dt, entrynum, g);
@@ -272,9 +288,11 @@ static void lguest_write_idt_entry(gate_desc *dt,
 	kvm_hypercall3(LHCALL_LOAD_IDT_ENTRY, entrynum, desc[0], desc[1]);
 }
 
-/* Changing to a different IDT is very rare: we keep the IDT up-to-date every
+/*
+ * Changing to a different IDT is very rare: we keep the IDT up-to-date every
  * time it is written, so we can simply loop through all entries and tell the
- * Host about them. */
+ * Host about them.
+ */
 static void lguest_load_idt(const struct desc_ptr *desc)
 {
 	unsigned int i;
@@ -305,9 +323,11 @@ static void lguest_load_gdt(const struct desc_ptr *desc)
 		kvm_hypercall3(LHCALL_LOAD_GDT_ENTRY, i, gdt[i].a, gdt[i].b);
 }
 
-/* For a single GDT entry which changes, we do the lazy thing: alter our GDT,
+/*
+ * For a single GDT entry which changes, we do the lazy thing: alter our GDT,
  * then tell the Host to reload the entire thing.  This operation is so rare
- * that this naive implementation is reasonable. */
+ * that this naive implementation is reasonable.
+ */
 static void lguest_write_gdt_entry(struct desc_struct *dt, int entrynum,
 				   const void *desc, int type)
 {
@@ -317,29 +337,36 @@ static void lguest_write_gdt_entry(struct desc_struct *dt, int entrynum,
 		       dt[entrynum].a, dt[entrynum].b);
 }
 
-/* OK, I lied.  There are three "thread local storage" GDT entries which change
+/*
+ * OK, I lied.  There are three "thread local storage" GDT entries which change
  * on every context switch (these three entries are how glibc implements
- * __thread variables).  So we have a hypercall specifically for this case. */
+ * __thread variables).  So we have a hypercall specifically for this case.
+ */
 static void lguest_load_tls(struct thread_struct *t, unsigned int cpu)
 {
-	/* There's one problem which normal hardware doesn't have: the Host
+	/*
+	 * There's one problem which normal hardware doesn't have: the Host
 	 * can't handle us removing entries we're currently using.  So we clear
-	 * the GS register here: if it's needed it'll be reloaded anyway. */
+	 * the GS register here: if it's needed it'll be reloaded anyway.
+	 */
 	lazy_load_gs(0);
 	lazy_hcall2(LHCALL_LOAD_TLS, __pa(&t->tls_array), cpu);
 }
 
-/*G:038 That's enough excitement for now, back to ploughing through each of
- * the different pv_ops structures (we're about 1/3 of the way through).
+/*G:038
+ * That's enough excitement for now, back to ploughing through each of the
+ * different pv_ops structures (we're about 1/3 of the way through).
  *
  * This is the Local Descriptor Table, another weird Intel thingy.  Linux only
  * uses this for some strange applications like Wine.  We don't do anything
- * here, so they'll get an informative and friendly Segmentation Fault. */
+ * here, so they'll get an informative and friendly Segmentation Fault.
+ */
 static void lguest_set_ldt(const void *addr, unsigned entries)
 {
 }
 
-/* This loads a GDT entry into the "Task Register": that entry points to a
+/*
+ * This loads a GDT entry into the "Task Register": that entry points to a
  * structure called the Task State Segment.  Some comments scattered though the
  * kernel code indicate that this used for task switching in ages past, along
  * with blood sacrifice and astrology.
@@ -347,19 +374,21 @@ static void lguest_set_ldt(const void *addr, unsigned entries)
  * Now there's nothing interesting in here that we don't get told elsewhere.
  * But the native version uses the "ltr" instruction, which makes the Host
  * complain to the Guest about a Segmentation Fault and it'll oops.  So we
- * override the native version with a do-nothing version. */
+ * override the native version with a do-nothing version.
+ */
 static void lguest_load_tr_desc(void)
 {
 }
 
-/* The "cpuid" instruction is a way of querying both the CPU identity
+/*
+ * The "cpuid" instruction is a way of querying both the CPU identity
  * (manufacturer, model, etc) and its features.  It was introduced before the
  * Pentium in 1993 and keeps getting extended by both Intel, AMD and others.
  * As you might imagine, after a decade and a half this treatment, it is now a
  * giant ball of hair.  Its entry in the current Intel manual runs to 28 pages.
  *
  * This instruction even it has its own Wikipedia entry.  The Wikipedia entry
- * has been translated into 4 languages.  I am not making this up!
+ * has been translated into 5 languages.  I am not making this up!
  *
  * We could get funky here and identify ourselves as "GenuineLguest", but
  * instead we just use the real "cpuid" instruction.  Then I pretty much turned
@@ -371,7 +400,8 @@ static void lguest_load_tr_desc(void)
  * Replacing the cpuid so we can turn features off is great for the kernel, but
  * anyone (including userspace) can just use the raw "cpuid" instruction and
  * the Host won't even notice since it isn't privileged.  So we try not to get
- * too worked up about it. */
+ * too worked up about it.
+ */
 static void lguest_cpuid(unsigned int *ax, unsigned int *bx,
 			 unsigned int *cx, unsigned int *dx)
 {
@@ -379,43 +409,63 @@ static void lguest_cpuid(unsigned int *ax, unsigned int *bx,
 
 	native_cpuid(ax, bx, cx, dx);
 	switch (function) {
-	case 0: /* ID and highest CPUID.  Futureproof a little by sticking to
-		 * older ones. */
+	/*
+	 * CPUID 0 gives the highest legal CPUID number (and the ID string).
+	 * We futureproof our code a little by sticking to known CPUID values.
+	 */
+	case 0:
 		if (*ax > 5)
 			*ax = 5;
 		break;
-	case 1:	/* Basic feature request. */
-		/* We only allow kernel to see SSE3, CMPXCHG16B and SSSE3 */
+
+	/*
+	 * CPUID 1 is a basic feature request.
+	 *
+	 * CX: we only allow kernel to see SSE3, CMPXCHG16B and SSSE3
+	 * DX: SSE, SSE2, FXSR, MMX, CMOV, CMPXCHG8B, TSC, FPU and PAE.
+	 */
+	case 1:
 		*cx &= 0x00002201;
-		/* SSE, SSE2, FXSR, MMX, CMOV, CMPXCHG8B, TSC, FPU, PAE. */
 		*dx &= 0x07808151;
-		/* The Host can do a nice optimization if it knows that the
+		/*
+		 * The Host can do a nice optimization if it knows that the
 		 * kernel mappings (addresses above 0xC0000000 or whatever
 		 * PAGE_OFFSET is set to) haven't changed.  But Linux calls
 		 * flush_tlb_user() for both user and kernel mappings unless
-		 * the Page Global Enable (PGE) feature bit is set. */
+		 * the Page Global Enable (PGE) feature bit is set.
+		 */
 		*dx |= 0x00002000;
-		/* We also lie, and say we're family id 5.  6 or greater
+		/*
+		 * We also lie, and say we're family id 5.  6 or greater
 		 * leads to a rdmsr in early_init_intel which we can't handle.
-		 * Family ID is returned as bits 8-12 in ax. */
+		 * Family ID is returned as bits 8-12 in ax.
+		 */
 		*ax &= 0xFFFFF0FF;
 		*ax |= 0x00000500;
 		break;
+	/*
+	 * 0x80000000 returns the highest Extended Function, so we futureproof
+	 * like we do above by limiting it to known fields.
+	 */
 	case 0x80000000:
-		/* Futureproof this a little: if they ask how much extended
-		 * processor information there is, limit it to known fields. */
 		if (*ax > 0x80000008)
 			*ax = 0x80000008;
 		break;
+
+	/*
+	 * PAE systems can mark pages as non-executable.  Linux calls this the
+	 * NX bit.  Intel calls it XD (eXecute Disable), AMD EVP (Enhanced
+	 * Virus Protection).  We just switch turn if off here, since we don't
+	 * support it.
+	 */
 	case 0x80000001:
-		/* Here we should fix nx cap depending on host. */
-		/* For this version of PAE, we just clear NX bit. */
 		*dx &= ~(1 << 20);
 		break;
 	}
 }
 
-/* Intel has four control registers, imaginatively named cr0, cr2, cr3 and cr4.
+/*
+ * Intel has four control registers, imaginatively named cr0, cr2, cr3 and cr4.
  * I assume there's a cr1, but it hasn't bothered us yet, so we'll not bother
  * it.  The Host needs to know when the Guest wants to change them, so we have
  * a whole series of functions like read_cr0() and write_cr0().
@@ -430,7 +480,8 @@ static void lguest_cpuid(unsigned int *ax, unsigned int *bx,
  * name like "FPUTRAP bit" be a little less cryptic?
  *
  * We store cr0 locally because the Host never changes it.  The Guest sometimes
- * wants to read it and we'd prefer not to bother the Host unnecessarily. */
+ * wants to read it and we'd prefer not to bother the Host unnecessarily.
+ */
 static unsigned long current_cr0;
 static void lguest_write_cr0(unsigned long val)
 {
@@ -443,18 +494,22 @@ static unsigned long lguest_read_cr0(void)
 	return current_cr0;
 }
 
-/* Intel provided a special instruction to clear the TS bit for people too cool
+/*
+ * Intel provided a special instruction to clear the TS bit for people too cool
  * to use write_cr0() to do it.  This "clts" instruction is faster, because all
- * the vowels have been optimized out. */
+ * the vowels have been optimized out.
+ */
 static void lguest_clts(void)
 {
 	lazy_hcall1(LHCALL_TS, 0);
 	current_cr0 &= ~X86_CR0_TS;
 }
 
-/* cr2 is the virtual address of the last page fault, which the Guest only ever
+/*
+ * cr2 is the virtual address of the last page fault, which the Guest only ever
  * reads.  The Host kindly writes this into our "struct lguest_data", so we
- * just read it out of there. */
+ * just read it out of there.
+ */
 static unsigned long lguest_read_cr2(void)
 {
 	return lguest_data.cr2;
@@ -463,10 +518,12 @@ static unsigned long lguest_read_cr2(void)
 /* See lguest_set_pte() below. */
 static bool cr3_changed = false;
 
-/* cr3 is the current toplevel pagetable page: the principle is the same as
+/*
+ * cr3 is the current toplevel pagetable page: the principle is the same as
  * cr0.  Keep a local copy, and tell the Host when it changes.  The only
  * difference is that our local copy is in lguest_data because the Host needs
- * to set it upon our initial hypercall. */
+ * to set it upon our initial hypercall.
+ */
 static void lguest_write_cr3(unsigned long cr3)
 {
 	lguest_data.pgdir = cr3;
@@ -538,10 +595,12 @@ static void lguest_write_cr4(unsigned long val)
  * the real page tables based on the Guests'.
  */
 
-/* The Guest calls this to set a second-level entry (pte), ie. to map a page
+/*
+ * The Guest calls this to set a second-level entry (pte), ie. to map a page
  * into a process' address space.  We set the entry then tell the Host the
  * toplevel and address this corresponds to.  The Guest uses one pagetable per
- * process, so we need to tell the Host which one we're changing (mm->pgd). */
+ * process, so we need to tell the Host which one we're changing (mm->pgd).
+ */
 static void lguest_pte_update(struct mm_struct *mm, unsigned long addr,
 			       pte_t *ptep)
 {
@@ -560,10 +619,13 @@ static void lguest_set_pte_at(struct mm_struct *mm, unsigned long addr,
 	lguest_pte_update(mm, addr, ptep);
 }
 
-/* The Guest calls lguest_set_pud to set a top-level entry and lguest_set_pmd
+/*
+ * The Guest calls lguest_set_pud to set a top-level entry and lguest_set_pmd
  * to set a middle-level entry when PAE is activated.
+ *
  * Again, we set the entry then tell the Host which page we changed,
- * and the index of the entry we changed. */
+ * and the index of the entry we changed.
+ */
 #ifdef CONFIG_X86_PAE
 static void lguest_set_pud(pud_t *pudp, pud_t pudval)
 {
@@ -582,8 +644,7 @@ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval)
 }
 #else
 
-/* The Guest calls lguest_set_pmd to set a top-level entry when PAE is not
- * activated. */
+/* The Guest calls lguest_set_pmd to set a top-level entry when !PAE. */
 static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval)
 {
 	native_set_pmd(pmdp, pmdval);
@@ -592,7 +653,8 @@ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval)
 }
 #endif
 
-/* There are a couple of legacy places where the kernel sets a PTE, but we
+/*
+ * There are a couple of legacy places where the kernel sets a PTE, but we
  * don't know the top level any more.  This is useless for us, since we don't
  * know which pagetable is changing or what address, so we just tell the Host
  * to forget all of them.  Fortunately, this is very rare.
@@ -600,7 +662,8 @@ static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval)
  * ... except in early boot when the kernel sets up the initial pagetables,
  * which makes booting astonishingly slow: 1.83 seconds!  So we don't even tell
  * the Host anything changed until we've done the first page table switch,
- * which brings boot back to 0.25 seconds. */
+ * which brings boot back to 0.25 seconds.
+ */
 static void lguest_set_pte(pte_t *ptep, pte_t pteval)
 {
 	native_set_pte(ptep, pteval);
@@ -628,7 +691,8 @@ void lguest_pmd_clear(pmd_t *pmdp)
 }
 #endif
 
-/* Unfortunately for Lguest, the pv_mmu_ops for page tables were based on
+/*
+ * Unfortunately for Lguest, the pv_mmu_ops for page tables were based on
  * native page table operations.  On native hardware you can set a new page
  * table entry whenever you want, but if you want to remove one you have to do
  * a TLB flush (a TLB is a little cache of page table entries kept by the CPU).
@@ -637,24 +701,29 @@ void lguest_pmd_clear(pmd_t *pmdp)
  * called when a valid entry is written, not when it's removed (ie. marked not
  * present).  Instead, this is where we come when the Guest wants to remove a
  * page table entry: we tell the Host to set that entry to 0 (ie. the present
- * bit is zero). */
+ * bit is zero).
+ */
 static void lguest_flush_tlb_single(unsigned long addr)
 {
 	/* Simply set it to zero: if it was not, it will fault back in. */
 	lazy_hcall3(LHCALL_SET_PTE, lguest_data.pgdir, addr, 0);
 }
 
-/* This is what happens after the Guest has removed a large number of entries.
+/*
+ * This is what happens after the Guest has removed a large number of entries.
  * This tells the Host that any of the page table entries for userspace might
- * have changed, ie. virtual addresses below PAGE_OFFSET. */
+ * have changed, ie. virtual addresses below PAGE_OFFSET.
+ */
 static void lguest_flush_tlb_user(void)
 {
 	lazy_hcall1(LHCALL_FLUSH_TLB, 0);
 }
 
-/* This is called when the kernel page tables have changed.  That's not very
+/*
+ * This is called when the kernel page tables have changed.  That's not very
  * common (unless the Guest is using highmem, which makes the Guest extremely
- * slow), so it's worth separating this from the user flushing above. */
+ * slow), so it's worth separating this from the user flushing above.
+ */
 static void lguest_flush_tlb_kernel(void)
 {
 	lazy_hcall1(LHCALL_FLUSH_TLB, 1);
@@ -691,23 +760,27 @@ static struct irq_chip lguest_irq_controller = {
 	.unmask		= enable_lguest_irq,
 };
 
-/* This sets up the Interrupt Descriptor Table (IDT) entry for each hardware
+/*
+ * This sets up the Interrupt Descriptor Table (IDT) entry for each hardware
  * interrupt (except 128, which is used for system calls), and then tells the
  * Linux infrastructure that each interrupt is controlled by our level-based
- * lguest interrupt controller. */
+ * lguest interrupt controller.
+ */
 static void __init lguest_init_IRQ(void)
 {
 	unsigned int i;
 
 	for (i = FIRST_EXTERNAL_VECTOR; i < NR_VECTORS; i++) {
-		/* Some systems map "vectors" to interrupts weirdly.  Lguest has
-		 * a straightforward 1 to 1 mapping, so force that here. */
+		/* Some systems map "vectors" to interrupts weirdly.  Not us! */
 		__get_cpu_var(vector_irq)[i] = i - FIRST_EXTERNAL_VECTOR;
 		if (i != SYSCALL_VECTOR)
 			set_intr_gate(i, interrupt[i - FIRST_EXTERNAL_VECTOR]);
 	}
-	/* This call is required to set up for 4k stacks, where we have
-	 * separate stacks for hard and soft interrupts. */
+
+	/*
+	 * This call is required to set up for 4k stacks, where we have
+	 * separate stacks for hard and soft interrupts.
+	 */
 	irq_ctx_init(smp_processor_id());
 }
 
@@ -729,31 +802,39 @@ static unsigned long lguest_get_wallclock(void)
 	return lguest_data.time.tv_sec;
 }
 
-/* The TSC is an Intel thing called the Time Stamp Counter.  The Host tells us
+/*
+ * The TSC is an Intel thing called the Time Stamp Counter.  The Host tells us
  * what speed it runs at, or 0 if it's unusable as a reliable clock source.
  * This matches what we want here: if we return 0 from this function, the x86
- * TSC clock will give up and not register itself. */
+ * TSC clock will give up and not register itself.
+ */
 static unsigned long lguest_tsc_khz(void)
 {
 	return lguest_data.tsc_khz;
 }
 
-/* If we can't use the TSC, the kernel falls back to our lower-priority
- * "lguest_clock", where we read the time value given to us by the Host. */
+/*
+ * If we can't use the TSC, the kernel falls back to our lower-priority
+ * "lguest_clock", where we read the time value given to us by the Host.
+ */
 static cycle_t lguest_clock_read(struct clocksource *cs)
 {
 	unsigned long sec, nsec;
 
-	/* Since the time is in two parts (seconds and nanoseconds), we risk
+	/*
+	 * Since the time is in two parts (seconds and nanoseconds), we risk
 	 * reading it just as it's changing from 99 & 0.999999999 to 100 and 0,
 	 * and getting 99 and 0.  As Linux tends to come apart under the stress
-	 * of time travel, we must be careful: */
+	 * of time travel, we must be careful:
+	 */
 	do {
 		/* First we read the seconds part. */
 		sec = lguest_data.time.tv_sec;
-		/* This read memory barrier tells the compiler and the CPU that
+		/*
+		 * This read memory barrier tells the compiler and the CPU that
 		 * this can't be reordered: we have to complete the above
-		 * before going on. */
+		 * before going on.
+		 */
 		rmb();
 		/* Now we read the nanoseconds part. */
 		nsec = lguest_data.time.tv_nsec;
@@ -777,9 +858,11 @@ static struct clocksource lguest_clock = {
 	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
-/* We also need a "struct clock_event_device": Linux asks us to set it to go
+/*
+ * We also need a "struct clock_event_device": Linux asks us to set it to go
  * off some time in the future.  Actually, James Morris figured all this out, I
- * just applied the patch. */
+ * just applied the patch.
+ */
 static int lguest_clockevent_set_next_event(unsigned long delta,
                                            struct clock_event_device *evt)
 {
@@ -829,8 +912,10 @@ static struct clock_event_device lguest_clockevent = {
 	.max_delta_ns           = LG_CLOCK_MAX_DELTA,
 };
 
-/* This is the Guest timer interrupt handler (hardware interrupt 0).  We just
- * call the clockevent infrastructure and it does whatever needs doing. */
+/*
+ * This is the Guest timer interrupt handler (hardware interrupt 0).  We just
+ * call the clockevent infrastructure and it does whatever needs doing.
+ */
 static void lguest_time_irq(unsigned int irq, struct irq_desc *desc)
 {
 	unsigned long flags;
@@ -841,10 +926,12 @@ static void lguest_time_irq(unsigned int irq, struct irq_desc *desc)
 	local_irq_restore(flags);
 }
 
-/* At some point in the boot process, we get asked to set up our timing
+/*
+ * At some point in the boot process, we get asked to set up our timing
  * infrastructure.  The kernel doesn't expect timer interrupts before this, but
  * we cleverly initialized the "blocked_interrupts" field of "struct
- * lguest_data" so that timer interrupts were blocked until now. */
+ * lguest_data" so that timer interrupts were blocked until now.
+ */
 static void lguest_time_init(void)
 {
 	/* Set up the timer interrupt (0) to go to our simple timer routine */
@@ -868,14 +955,16 @@ static void lguest_time_init(void)
  * to work.  They're pretty simple.
  */
 
-/* The Guest needs to tell the Host what stack it expects traps to use.  For
+/*
+ * The Guest needs to tell the Host what stack it expects traps to use.  For
  * native hardware, this is part of the Task State Segment mentioned above in
  * lguest_load_tr_desc(), but to help hypervisors there's this special call.
  *
  * We tell the Host the segment we want to use (__KERNEL_DS is the kernel data
  * segment), the privilege level (we're privilege level 1, the Host is 0 and
  * will not tolerate us trying to use that), the stack pointer, and the number
- * of pages in the stack. */
+ * of pages in the stack.
+ */
 static void lguest_load_sp0(struct tss_struct *tss,
 			    struct thread_struct *thread)
 {
@@ -889,7 +978,8 @@ static void lguest_set_debugreg(int regno, unsigned long value)
 	/* FIXME: Implement */
 }
 
-/* There are times when the kernel wants to make sure that no memory writes are
+/*
+ * There are times when the kernel wants to make sure that no memory writes are
  * caught in the cache (that they've all reached real hardware devices).  This
  * doesn't matter for the Guest which has virtual hardware.
  *
@@ -903,11 +993,13 @@ static void lguest_wbinvd(void)
 {
 }
 
-/* If the Guest expects to have an Advanced Programmable Interrupt Controller,
+/*
+ * If the Guest expects to have an Advanced Programmable Interrupt Controller,
  * we play dumb by ignoring writes and returning 0 for reads.  So it's no
  * longer Programmable nor Controlling anything, and I don't think 8 lines of
  * code qualifies for Advanced.  It will also never interrupt anything.  It
- * does, however, allow us to get through the Linux boot code. */
+ * does, however, allow us to get through the Linux boot code.
+ */
 #ifdef CONFIG_X86_LOCAL_APIC
 static void lguest_apic_write(u32 reg, u32 v)
 {
@@ -956,11 +1048,13 @@ static void lguest_safe_halt(void)
 	kvm_hypercall0(LHCALL_HALT);
 }
 
-/* The SHUTDOWN hypercall takes a string to describe what's happening, and
+/*
+ * The SHUTDOWN hypercall takes a string to describe what's happening, and
  * an argument which says whether this to restart (reboot) the Guest or not.
  *
  * Note that the Host always prefers that the Guest speak in physical addresses
- * rather than virtual addresses, so we use __pa() here. */
+ * rather than virtual addresses, so we use __pa() here.
+ */
 static void lguest_power_off(void)
 {
 	kvm_hypercall2(LHCALL_SHUTDOWN, __pa("Power down"),
@@ -991,8 +1085,10 @@ static __init char *lguest_memory_setup(void)
 	 * nice to move it back to lguest_init.  Patch welcome... */
 	atomic_notifier_chain_register(&panic_notifier_list, &paniced);
 
-	/* The Linux bootloader header contains an "e820" memory map: the
-	 * Launcher populated the first entry with our memory limit. */
+	/*
+	 *The Linux bootloader header contains an "e820" memory map: the
+	 * Launcher populated the first entry with our memory limit.
+	 */
 	e820_add_region(boot_params.e820_map[0].addr,
 			  boot_params.e820_map[0].size,
 			  boot_params.e820_map[0].type);
@@ -1001,16 +1097,17 @@ static __init char *lguest_memory_setup(void)
 	return "LGUEST";
 }
 
-/* We will eventually use the virtio console device to produce console output,
+/*
+ * We will eventually use the virtio console device to produce console output,
  * but before that is set up we use LHCALL_NOTIFY on normal memory to produce
- * console output. */
+ * console output.
+ */
 static __init int early_put_chars(u32 vtermno, const char *buf, int count)
 {
 	char scratch[17];
 	unsigned int len = count;
 
-	/* We use a nul-terminated string, so we have to make a copy.  Icky,
-	 * huh? */
+	/* We use a nul-terminated string, so we make a copy.  Icky, huh? */
 	if (len > sizeof(scratch) - 1)
 		len = sizeof(scratch) - 1;
 	scratch[len] = '\0';
@@ -1021,8 +1118,10 @@ static __init int early_put_chars(u32 vtermno, const char *buf, int count)
 	return len;
 }
 
-/* Rebooting also tells the Host we're finished, but the RESTART flag tells the
- * Launcher to reboot us. */
+/*
+ * Rebooting also tells the Host we're finished, but the RESTART flag tells the
+ * Launcher to reboot us.
+ */
 static void lguest_restart(char *reason)
 {
 	kvm_hypercall2(LHCALL_SHUTDOWN, __pa(reason), LGUEST_SHUTDOWN_RESTART);
@@ -1049,7 +1148,8 @@ static void lguest_restart(char *reason)
  * fit comfortably.
  *
  * First we need assembly templates of each of the patchable Guest operations,
- * and these are in i386_head.S. */
+ * and these are in i386_head.S.
+ */
 
 /*G:060 We construct a table from the assembler templates: */
 static const struct lguest_insns
@@ -1060,9 +1160,11 @@ static const struct lguest_insns
 	[PARAVIRT_PATCH(pv_irq_ops.save_fl)] = { lgstart_pushf, lgend_pushf },
 };
 
-/* Now our patch routine is fairly simple (based on the native one in
+/*
+ * Now our patch routine is fairly simple (based on the native one in
  * paravirt.c).  If we have a replacement, we copy it in and return how much of
- * the available space we used. */
+ * the available space we used.
+ */
 static unsigned lguest_patch(u8 type, u16 clobber, void *ibuf,
 			     unsigned long addr, unsigned len)
 {
@@ -1074,8 +1176,7 @@ static unsigned lguest_patch(u8 type, u16 clobber, void *ibuf,
 
 	insn_len = lguest_insns[type].end - lguest_insns[type].start;
 
-	/* Similarly if we can't fit replacement (shouldn't happen, but let's
-	 * be thorough). */
+	/* Similarly if it can't fit (doesn't happen, but let's be thorough). */
 	if (len < insn_len)
 		return paravirt_patch_default(type, clobber, ibuf, addr, len);
 
@@ -1084,22 +1185,28 @@ static unsigned lguest_patch(u8 type, u16 clobber, void *ibuf,
 	return insn_len;
 }
 
-/*G:029 Once we get to lguest_init(), we know we're a Guest.  The various
+/*G:029
+ * Once we get to lguest_init(), we know we're a Guest.  The various
  * pv_ops structures in the kernel provide points for (almost) every routine we
- * have to override to avoid privileged instructions. */
+ * have to override to avoid privileged instructions.
+ */
 __init void lguest_init(void)
 {
-	/* We're under lguest, paravirt is enabled, and we're running at
-	 * privilege level 1, not 0 as normal. */
+	/* We're under lguest. */
 	pv_info.name = "lguest";
+	/* Paravirt is enabled. */
 	pv_info.paravirt_enabled = 1;
+	/* We're running at privilege level 1, not 0 as normal. */
 	pv_info.kernel_rpl = 1;
+	/* Everyone except Xen runs with this set. */
 	pv_info.shared_kernel_pmd = 1;
 
-	/* We set up all the lguest overrides for sensitive operations.  These
-	 * are detailed with the operations themselves. */
+	/*
+	 * We set up all the lguest overrides for sensitive operations.  These
+	 * are detailed with the operations themselves.
+	 */
 
-	/* interrupt-related operations */
+	/* Interrupt-related operations */
 	pv_irq_ops.init_IRQ = lguest_init_IRQ;
 	pv_irq_ops.save_fl = PV_CALLEE_SAVE(save_fl);
 	pv_irq_ops.restore_fl = __PV_IS_CALLEE_SAVE(lg_restore_fl);
@@ -1107,11 +1214,11 @@ __init void lguest_init(void)
 	pv_irq_ops.irq_enable = __PV_IS_CALLEE_SAVE(lg_irq_enable);
 	pv_irq_ops.safe_halt = lguest_safe_halt;
 
-	/* init-time operations */
+	/* Setup operations */
 	pv_init_ops.memory_setup = lguest_memory_setup;
 	pv_init_ops.patch = lguest_patch;
 
-	/* Intercepts of various cpu instructions */
+	/* Intercepts of various CPU instructions */
 	pv_cpu_ops.load_gdt = lguest_load_gdt;
 	pv_cpu_ops.cpuid = lguest_cpuid;
 	pv_cpu_ops.load_idt = lguest_load_idt;
@@ -1132,7 +1239,7 @@ __init void lguest_init(void)
 	pv_cpu_ops.start_context_switch = paravirt_start_context_switch;
 	pv_cpu_ops.end_context_switch = lguest_end_context_switch;
 
-	/* pagetable management */
+	/* Pagetable management */
 	pv_mmu_ops.write_cr3 = lguest_write_cr3;
 	pv_mmu_ops.flush_tlb_user = lguest_flush_tlb_user;
 	pv_mmu_ops.flush_tlb_single = lguest_flush_tlb_single;
@@ -1154,54 +1261,71 @@ __init void lguest_init(void)
 	pv_mmu_ops.pte_update_defer = lguest_pte_update;
 
 #ifdef CONFIG_X86_LOCAL_APIC
-	/* apic read/write intercepts */
+	/* APIC read/write intercepts */
 	set_lguest_basic_apic_ops();
 #endif
 
-	/* time operations */
+	/* Time operations */
 	pv_time_ops.get_wallclock = lguest_get_wallclock;
 	pv_time_ops.time_init = lguest_time_init;
 	pv_time_ops.get_tsc_khz = lguest_tsc_khz;
 
-	/* Now is a good time to look at the implementations of these functions
-	 * before returning to the rest of lguest_init(). */
+	/*
+	 * Now is a good time to look at the implementations of these functions
+	 * before returning to the rest of lguest_init().
+	 */
 
-	/*G:070 Now we've seen all the paravirt_ops, we return to
+	/*G:070
+	 * Now we've seen all the paravirt_ops, we return to
 	 * lguest_init() where the rest of the fairly chaotic boot setup
-	 * occurs. */
+	 * occurs.
+	 */
 
-	/* The stack protector is a weird thing where gcc places a canary
+	/*
+	 * The stack protector is a weird thing where gcc places a canary
 	 * value on the stack and then checks it on return.  This file is
 	 * compiled with -fno-stack-protector it, so we got this far without
 	 * problems.  The value of the canary is kept at offset 20 from the
 	 * %gs register, so we need to set that up before calling C functions
-	 * in other files. */
+	 * in other files.
+	 */
 	setup_stack_canary_segment(0);
-	/* We could just call load_stack_canary_segment(), but we might as
-	 * call switch_to_new_gdt() which loads the whole table and sets up
-	 * the per-cpu segment descriptor register %fs as well. */
+
+	/*
+	 * We could just call load_stack_canary_segment(), but we might as well
+	 * call switch_to_new_gdt() which loads the whole table and sets up the
+	 * per-cpu segment descriptor register %fs as well.
+	 */
 	switch_to_new_gdt(0);
 
 	/* As described in head_32.S, we map the first 128M of memory. */
 	max_pfn_mapped = (128*1024*1024) >> PAGE_SHIFT;
 
-	/* The Host<->Guest Switcher lives at the top of our address space, and
+	/*
+	 * The Host<->Guest Switcher lives at the top of our address space, and
 	 * the Host told us how big it is when we made LGUEST_INIT hypercall:
-	 * it put the answer in lguest_data.reserve_mem  */
+	 * it put the answer in lguest_data.reserve_mem
+	 */
 	reserve_top_address(lguest_data.reserve_mem);
 
-	/* If we don't initialize the lock dependency checker now, it crashes
-	 * paravirt_disable_iospace. */
+	/*
+	 * If we don't initialize the lock dependency checker now, it crashes
+	 * paravirt_disable_iospace.
+	 */
 	lockdep_init();
 
-	/* The IDE code spends about 3 seconds probing for disks: if we reserve
+	/*
+	 * The IDE code spends about 3 seconds probing for disks: if we reserve
 	 * all the I/O ports up front it can't get them and so doesn't probe.
 	 * Other device drivers are similar (but less severe).  This cuts the
-	 * kernel boot time on my machine from 4.1 seconds to 0.45 seconds. */
+	 * kernel boot time on my machine from 4.1 seconds to 0.45 seconds.
+	 */
 	paravirt_disable_iospace();
 
-	/* This is messy CPU setup stuff which the native boot code does before
-	 * start_kernel, so we have to do, too: */
+	/*
+	 * This is messy CPU setup stuff which the native boot code does before
+	 * start_kernel, so we have to do, too:
+	 */
 	cpu_detect(&new_cpu_data);
 	/* head.S usually sets up the first capability word, so do it here. */
 	new_cpu_data.x86_capability[0] = cpuid_edx(1);
@@ -1218,22 +1342,28 @@ __init void lguest_init(void)
 	acpi_ht = 0;
 #endif
 
-	/* We set the preferred console to "hvc".  This is the "hypervisor
+	/*
+	 * We set the preferred console to "hvc".  This is the "hypervisor
 	 * virtual console" driver written by the PowerPC people, which we also
-	 * adapted for lguest's use. */
+	 * adapted for lguest's use.
+	 */
 	add_preferred_console("hvc", 0, NULL);
 
 	/* Register our very early console. */
 	virtio_cons_early_init(early_put_chars);
 
-	/* Last of all, we set the power management poweroff hook to point to
+	/*
+	 * Last of all, we set the power management poweroff hook to point to
 	 * the Guest routine to power off, and the reboot hook to our restart
-	 * routine. */
+	 * routine.
+	 */
 	pm_power_off = lguest_power_off;
 	machine_ops.restart = lguest_restart;
 
-	/* Now we're set up, call i386_start_kernel() in head32.c and we proceed
-	 * to boot as normal.  It never returns. */
+	/*
+	 * Now we're set up, call i386_start_kernel() in head32.c and we proceed
+	 * to boot as normal.  It never returns.
+	 */
 	i386_start_kernel();
 }
 /*
diff --git a/arch/x86/lguest/i386_head.S b/arch/x86/lguest/i386_head.S
index a9c8cfe61cd..db6aa95eb05 100644
--- a/arch/x86/lguest/i386_head.S
+++ b/arch/x86/lguest/i386_head.S
@@ -5,7 +5,8 @@
 #include <asm/thread_info.h>
 #include <asm/processor-flags.h>
 
-/*G:020 Our story starts with the kernel booting into startup_32 in
+/*G:020
+ * Our story starts with the kernel booting into startup_32 in
  * arch/x86/kernel/head_32.S.  It expects a boot header, which is created by
  * the bootloader (the Launcher in our case).
  *
@@ -21,11 +22,14 @@
  * data without remembering to subtract __PAGE_OFFSET!
  *
  * The .section line puts this code in .init.text so it will be discarded after
- * boot. */
+ * boot.
+ */
 .section .init.text, "ax", @progbits
 ENTRY(lguest_entry)
-	/* We make the "initialization" hypercall now to tell the Host about
-	 * us, and also find out where it put our page tables. */
+	/*
+	 * We make the "initialization" hypercall now to tell the Host about
+	 * us, and also find out where it put our page tables.
+	 */
 	movl $LHCALL_LGUEST_INIT, %eax
 	movl $lguest_data - __PAGE_OFFSET, %ebx
 	.byte 0x0f,0x01,0xc1 /* KVM_HYPERCALL */
@@ -33,13 +37,14 @@ ENTRY(lguest_entry)
 	/* Set up the initial stack so we can run C code. */
 	movl $(init_thread_union+THREAD_SIZE),%esp
 
-	/* Jumps are relative, and we're running __PAGE_OFFSET too low at the
-	 * moment. */
+	/* Jumps are relative: we're running __PAGE_OFFSET too low. */
 	jmp lguest_init+__PAGE_OFFSET
 
-/*G:055 We create a macro which puts the assembler code between lgstart_ and
- * lgend_ markers.  These templates are put in the .text section: they can't be
- * discarded after boot as we may need to patch modules, too. */
+/*G:055
+ * We create a macro which puts the assembler code between lgstart_ and lgend_
+ * markers.  These templates are put in the .text section: they can't be
+ * discarded after boot as we may need to patch modules, too.
+ */
 .text
 #define LGUEST_PATCH(name, insns...)			\
 	lgstart_##name:	insns; lgend_##name:;		\
@@ -48,58 +53,74 @@ ENTRY(lguest_entry)
 LGUEST_PATCH(cli, movl $0, lguest_data+LGUEST_DATA_irq_enabled)
 LGUEST_PATCH(pushf, movl lguest_data+LGUEST_DATA_irq_enabled, %eax)
 
-/*G:033 But using those wrappers is inefficient (we'll see why that doesn't
- * matter for save_fl and irq_disable later).  If we write our routines
- * carefully in assembler, we can avoid clobbering any registers and avoid
- * jumping through the wrapper functions.
+/*G:033
+ * But using those wrappers is inefficient (we'll see why that doesn't matter
+ * for save_fl and irq_disable later).  If we write our routines carefully in
+ * assembler, we can avoid clobbering any registers and avoid jumping through
+ * the wrapper functions.
  *
  * I skipped over our first piece of assembler, but this one is worth studying
- * in a bit more detail so I'll describe in easy stages.  First, the routine
- * to enable interrupts: */
+ * in a bit more detail so I'll describe in easy stages.  First, the routine to
+ * enable interrupts:
+ */
 ENTRY(lg_irq_enable)
-	/* The reverse of irq_disable, this sets lguest_data.irq_enabled to
-	 * X86_EFLAGS_IF (ie. "Interrupts enabled"). */
+	/*
+	 * The reverse of irq_disable, this sets lguest_data.irq_enabled to
+	 * X86_EFLAGS_IF (ie. "Interrupts enabled").
+	 */
 	movl $X86_EFLAGS_IF, lguest_data+LGUEST_DATA_irq_enabled
-	/* But now we need to check if the Host wants to know: there might have
+	/*
+	 * But now we need to check if the Host wants to know: there might have
 	 * been interrupts waiting to be delivered, in which case it will have
 	 * set lguest_data.irq_pending to X86_EFLAGS_IF.  If it's not zero, we
-	 * jump to send_interrupts, otherwise we're done. */
+	 * jump to send_interrupts, otherwise we're done.
+	 */
 	testl $0, lguest_data+LGUEST_DATA_irq_pending
 	jnz send_interrupts
-	/* One cool thing about x86 is that you can do many things without using
+	/*
+	 * One cool thing about x86 is that you can do many things without using
 	 * a register.  In this case, the normal path hasn't needed to save or
-	 * restore any registers at all! */
+	 * restore any registers at all!
+	 */
 	ret
 send_interrupts:
-	/* OK, now we need a register: eax is used for the hypercall number,
+	/*
+	 * OK, now we need a register: eax is used for the hypercall number,
 	 * which is LHCALL_SEND_INTERRUPTS.
 	 *
 	 * We used not to bother with this pending detection at all, which was
 	 * much simpler.  Sooner or later the Host would realize it had to
 	 * send us an interrupt.  But that turns out to make performance 7
 	 * times worse on a simple tcp benchmark.  So now we do this the hard
-	 * way. */
+	 * way.
+	 */
 	pushl %eax
 	movl $LHCALL_SEND_INTERRUPTS, %eax
-	/* This is a vmcall instruction (same thing that KVM uses).  Older
+	/*
+	 * This is a vmcall instruction (same thing that KVM uses).  Older
 	 * assembler versions might not know the "vmcall" instruction, so we
-	 * create one manually here. */
+	 * create one manually here.
+	 */
 	.byte 0x0f,0x01,0xc1 /* KVM_HYPERCALL */
 	popl %eax
 	ret
 
-/* Finally, the "popf" or "restore flags" routine.  The %eax register holds the
+/*
+ * Finally, the "popf" or "restore flags" routine.  The %eax register holds the
  * flags (in practice, either X86_EFLAGS_IF or 0): if it's X86_EFLAGS_IF we're
- * enabling interrupts again, if it's 0 we're leaving them off. */
+ * enabling interrupts again, if it's 0 we're leaving them off.
+ */
 ENTRY(lg_restore_fl)
 	/* This is just "lguest_data.irq_enabled = flags;" */
 	movl %eax, lguest_data+LGUEST_DATA_irq_enabled
-	/* Now, if the %eax value has enabled interrupts and
+	/*
+	 * Now, if the %eax value has enabled interrupts and
 	 * lguest_data.irq_pending is set, we want to tell the Host so it can
 	 * deliver any outstanding interrupts.  Fortunately, both values will
 	 * be X86_EFLAGS_IF (ie. 512) in that case, and the "testl"
 	 * instruction will AND them together for us.  If both are set, we
-	 * jump to send_interrupts. */
+	 * jump to send_interrupts.
+	 */
 	testl lguest_data+LGUEST_DATA_irq_pending, %eax
 	jnz send_interrupts
 	/* Again, the normal path has used no extra registers.  Clever, huh? */
@@ -109,22 +130,24 @@ ENTRY(lg_restore_fl)
 .global lguest_noirq_start
 .global lguest_noirq_end
 
-/*M:004 When the Host reflects a trap or injects an interrupt into the Guest,
- * it sets the eflags interrupt bit on the stack based on
- * lguest_data.irq_enabled, so the Guest iret logic does the right thing when
- * restoring it.  However, when the Host sets the Guest up for direct traps,
- * such as system calls, the processor is the one to push eflags onto the
- * stack, and the interrupt bit will be 1 (in reality, interrupts are always
- * enabled in the Guest).
+/*M:004
+ * When the Host reflects a trap or injects an interrupt into the Guest, it
+ * sets the eflags interrupt bit on the stack based on lguest_data.irq_enabled,
+ * so the Guest iret logic does the right thing when restoring it.  However,
+ * when the Host sets the Guest up for direct traps, such as system calls, the
+ * processor is the one to push eflags onto the stack, and the interrupt bit
+ * will be 1 (in reality, interrupts are always enabled in the Guest).
  *
  * This turns out to be harmless: the only trap which should happen under Linux
  * with interrupts disabled is Page Fault (due to our lazy mapping of vmalloc
  * regions), which has to be reflected through the Host anyway.  If another
  * trap *does* go off when interrupts are disabled, the Guest will panic, and
- * we'll never get to this iret! :*/
+ * we'll never get to this iret!
+:*/
 
-/*G:045 There is one final paravirt_op that the Guest implements, and glancing
- * at it you can see why I left it to last.  It's *cool*!  It's in *assembler*!
+/*G:045
+ * There is one final paravirt_op that the Guest implements, and glancing at it
+ * you can see why I left it to last.  It's *cool*!  It's in *assembler*!
  *
  * The "iret" instruction is used to return from an interrupt or trap.  The
  * stack looks like this:
@@ -148,15 +171,18 @@ ENTRY(lg_restore_fl)
  * return to userspace or wherever.  Our solution to this is to surround the
  * code with lguest_noirq_start: and lguest_noirq_end: labels.  We tell the
  * Host that it is *never* to interrupt us there, even if interrupts seem to be
- * enabled. */
+ * enabled.
+ */
 ENTRY(lguest_iret)
 	pushl	%eax
 	movl	12(%esp), %eax
 lguest_noirq_start:
-	/* Note the %ss: segment prefix here.  Normal data accesses use the
+	/*
+	 * Note the %ss: segment prefix here.  Normal data accesses use the
 	 * "ds" segment, but that will have already been restored for whatever
 	 * we're returning to (such as userspace): we can't trust it.  The %ss:
-	 * prefix makes sure we use the stack segment, which is still valid. */
+	 * prefix makes sure we use the stack segment, which is still valid.
+	 */
 	movl	%eax,%ss:lguest_data+LGUEST_DATA_irq_enabled
 	popl	%eax
 	iret
diff --git a/drivers/lguest/core.c b/drivers/lguest/core.c
index a6974e9b8eb..cd058bc903f 100644
--- a/drivers/lguest/core.c
+++ b/drivers/lguest/core.c
@@ -1,6 +1,8 @@
-/*P:400 This contains run_guest() which actually calls into the Host<->Guest
+/*P:400
+ * This contains run_guest() which actually calls into the Host<->Guest
  * Switcher and analyzes the return, such as determining if the Guest wants the
- * Host to do something.  This file also contains useful helper routines. :*/
+ * Host to do something.  This file also contains useful helper routines.
+:*/
 #include <linux/module.h>
 #include <linux/stringify.h>
 #include <linux/stddef.h>
@@ -24,7 +26,8 @@ static struct page **switcher_page;
 /* This One Big lock protects all inter-guest data structures. */
 DEFINE_MUTEX(lguest_lock);
 
-/*H:010 We need to set up the Switcher at a high virtual address.  Remember the
+/*H:010
+ * We need to set up the Switcher at a high virtual address.  Remember the
  * Switcher is a few hundred bytes of assembler code which actually changes the
  * CPU to run the Guest, and then changes back to the Host when a trap or
  * interrupt happens.
@@ -33,7 +36,8 @@ DEFINE_MUTEX(lguest_lock);
  * Host since it will be running as the switchover occurs.
  *
  * Trying to map memory at a particular address is an unusual thing to do, so
- * it's not a simple one-liner. */
+ * it's not a simple one-liner.
+ */
 static __init int map_switcher(void)
 {
 	int i, err;
@@ -47,8 +51,10 @@ static __init int map_switcher(void)
 	 * easy.
 	 */
 
-	/* We allocate an array of struct page pointers.  map_vm_area() wants
-	 * this, rather than just an array of pages. */
+	/*
+	 * We allocate an array of struct page pointers.  map_vm_area() wants
+	 * this, rather than just an array of pages.
+	 */
 	switcher_page = kmalloc(sizeof(switcher_page[0])*TOTAL_SWITCHER_PAGES,
 				GFP_KERNEL);
 	if (!switcher_page) {
@@ -56,8 +62,10 @@ static __init int map_switcher(void)
 		goto out;
 	}
 
-	/* Now we actually allocate the pages.  The Guest will see these pages,
-	 * so we make sure they're zeroed. */
+	/*
+	 * Now we actually allocate the pages.  The Guest will see these pages,
+	 * so we make sure they're zeroed.
+	 */
 	for (i = 0; i < TOTAL_SWITCHER_PAGES; i++) {
 		unsigned long addr = get_zeroed_page(GFP_KERNEL);
 		if (!addr) {
@@ -67,19 +75,23 @@ static __init int map_switcher(void)
 		switcher_page[i] = virt_to_page(addr);
 	}
 
-	/* First we check that the Switcher won't overlap the fixmap area at
+	/*
+	 * First we check that the Switcher won't overlap the fixmap area at
 	 * the top of memory.  It's currently nowhere near, but it could have
-	 * very strange effects if it ever happened. */
+	 * very strange effects if it ever happened.
+	 */
 	if (SWITCHER_ADDR + (TOTAL_SWITCHER_PAGES+1)*PAGE_SIZE > FIXADDR_START){
 		err = -ENOMEM;
 		printk("lguest: mapping switcher would thwack fixmap\n");
 		goto free_pages;
 	}
 
-	/* Now we reserve the "virtual memory area" we want: 0xFFC00000
+	/*
+	 * Now we reserve the "virtual memory area" we want: 0xFFC00000
 	 * (SWITCHER_ADDR).  We might not get it in theory, but in practice
 	 * it's worked so far.  The end address needs +1 because __get_vm_area
-	 * allocates an extra guard page, so we need space for that. */
+	 * allocates an extra guard page, so we need space for that.
+	 */
 	switcher_vma = __get_vm_area(TOTAL_SWITCHER_PAGES * PAGE_SIZE,
 				     VM_ALLOC, SWITCHER_ADDR, SWITCHER_ADDR
 				     + (TOTAL_SWITCHER_PAGES+1) * PAGE_SIZE);
@@ -89,11 +101,13 @@ static __init int map_switcher(void)
 		goto free_pages;
 	}
 
-	/* This code actually sets up the pages we've allocated to appear at
+	/*
+	 * This code actually sets up the pages we've allocated to appear at
 	 * SWITCHER_ADDR.  map_vm_area() takes the vma we allocated above, the
 	 * kind of pages we're mapping (kernel pages), and a pointer to our
 	 * array of struct pages.  It increments that pointer, but we don't
-	 * care. */
+	 * care.
+	 */
 	pagep = switcher_page;
 	err = map_vm_area(switcher_vma, PAGE_KERNEL_EXEC, &pagep);
 	if (err) {
@@ -101,8 +115,10 @@ static __init int map_switcher(void)
 		goto free_vma;
 	}
 
-	/* Now the Switcher is mapped at the right address, we can't fail!
-	 * Copy in the compiled-in Switcher code (from <arch>_switcher.S). */
+	/*
+	 * Now the Switcher is mapped at the right address, we can't fail!
+	 * Copy in the compiled-in Switcher code (from <arch>_switcher.S).
+	 */
 	memcpy(switcher_vma->addr, start_switcher_text,
 	       end_switcher_text - start_switcher_text);
 
@@ -124,8 +140,7 @@ out:
 }
 /*:*/
 
-/* Cleaning up the mapping when the module is unloaded is almost...
- * too easy. */
+/* Cleaning up the mapping when the module is unloaded is almost... too easy. */
 static void unmap_switcher(void)
 {
 	unsigned int i;
@@ -151,16 +166,19 @@ static void unmap_switcher(void)
  * But we can't trust the Guest: it might be trying to access the Launcher
  * code.  We have to check that the range is below the pfn_limit the Launcher
  * gave us.  We have to make sure that addr + len doesn't give us a false
- * positive by overflowing, too. */
+ * positive by overflowing, too.
+ */
 bool lguest_address_ok(const struct lguest *lg,
 		       unsigned long addr, unsigned long len)
 {
 	return (addr+len) / PAGE_SIZE < lg->pfn_limit && (addr+len >= addr);
 }
 
-/* This routine copies memory from the Guest.  Here we can see how useful the
+/*
+ * This routine copies memory from the Guest.  Here we can see how useful the
  * kill_lguest() routine we met in the Launcher can be: we return a random
- * value (all zeroes) instead of needing to return an error. */
+ * value (all zeroes) instead of needing to return an error.
+ */
 void __lgread(struct lg_cpu *cpu, void *b, unsigned long addr, unsigned bytes)
 {
 	if (!lguest_address_ok(cpu->lg, addr, bytes)
@@ -181,9 +199,11 @@ void __lgwrite(struct lg_cpu *cpu, unsigned long addr, const void *b,
 }
 /*:*/
 
-/*H:030 Let's jump straight to the the main loop which runs the Guest.
+/*H:030
+ * Let's jump straight to the the main loop which runs the Guest.
  * Remember, this is called by the Launcher reading /dev/lguest, and we keep
- * going around and around until something interesting happens. */
+ * going around and around until something interesting happens.
+ */
 int run_guest(struct lg_cpu *cpu, unsigned long __user *user)
 {
 	/* We stop running once the Guest is dead. */
@@ -195,8 +215,10 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user)
 		if (cpu->hcall)
 			do_hypercalls(cpu);
 
-		/* It's possible the Guest did a NOTIFY hypercall to the
-		 * Launcher, in which case we return from the read() now. */
+		/*
+		 * It's possible the Guest did a NOTIFY hypercall to the
+		 * Launcher, in which case we return from the read() now.
+		 */
 		if (cpu->pending_notify) {
 			if (!send_notify_to_eventfd(cpu)) {
 				if (put_user(cpu->pending_notify, user))
@@ -209,29 +231,39 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user)
 		if (signal_pending(current))
 			return -ERESTARTSYS;
 
-		/* Check if there are any interrupts which can be delivered now:
+		/*
+		 * Check if there are any interrupts which can be delivered now:
 		 * if so, this sets up the hander to be executed when we next
-		 * run the Guest. */
+		 * run the Guest.
+		 */
 		irq = interrupt_pending(cpu, &more);
 		if (irq < LGUEST_IRQS)
 			try_deliver_interrupt(cpu, irq, more);
 
-		/* All long-lived kernel loops need to check with this horrible
+		/*
+		 * All long-lived kernel loops need to check with this horrible
 		 * thing called the freezer.  If the Host is trying to suspend,
-		 * it stops us. */
+		 * it stops us.
+		 */
 		try_to_freeze();
 
-		/* Just make absolutely sure the Guest is still alive.  One of
-		 * those hypercalls could have been fatal, for example. */
+		/*
+		 * Just make absolutely sure the Guest is still alive.  One of
+		 * those hypercalls could have been fatal, for example.
+		 */
 		if (cpu->lg->dead)
 			break;
 
-		/* If the Guest asked to be stopped, we sleep.  The Guest's
-		 * clock timer will wake us. */
+		/*
+		 * If the Guest asked to be stopped, we sleep.  The Guest's
+		 * clock timer will wake us.
+		 */
 		if (cpu->halted) {
 			set_current_state(TASK_INTERRUPTIBLE);
-			/* Just before we sleep, make sure no interrupt snuck in
-			 * which we should be doing. */
+			/*
+			 * Just before we sleep, make sure no interrupt snuck in
+			 * which we should be doing.
+			 */
 			if (interrupt_pending(cpu, &more) < LGUEST_IRQS)
 				set_current_state(TASK_RUNNING);
 			else
@@ -239,8 +271,10 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user)
 			continue;
 		}
 
-		/* OK, now we're ready to jump into the Guest.  First we put up
-		 * the "Do Not Disturb" sign: */
+		/*
+		 * OK, now we're ready to jump into the Guest.  First we put up
+		 * the "Do Not Disturb" sign:
+		 */
 		local_irq_disable();
 
 		/* Actually run the Guest until something happens. */
@@ -327,8 +361,10 @@ static void __exit fini(void)
 }
 /*:*/
 
-/* The Host side of lguest can be a module.  This is a nice way for people to
- * play with it.  */
+/*
+ * The Host side of lguest can be a module.  This is a nice way for people to
+ * play with it.
+ */
 module_init(init);
 module_exit(fini);
 MODULE_LICENSE("GPL");
diff --git a/drivers/lguest/hypercalls.c b/drivers/lguest/hypercalls.c
index c29ffa19cb7..787ab4bc09f 100644
--- a/drivers/lguest/hypercalls.c
+++ b/drivers/lguest/hypercalls.c
@@ -1,8 +1,10 @@
-/*P:500 Just as userspace programs request kernel operations through a system
+/*P:500
+ * Just as userspace programs request kernel operations through a system
  * call, the Guest requests Host operations through a "hypercall".  You might
  * notice this nomenclature doesn't really follow any logic, but the name has
  * been around for long enough that we're stuck with it.  As you'd expect, this
- * code is basically a one big switch statement. :*/
+ * code is basically a one big switch statement.
+:*/
 
 /*  Copyright (C) 2006 Rusty Russell IBM Corporation
 
@@ -28,30 +30,41 @@
 #include <asm/pgtable.h>
 #include "lg.h"
 
-/*H:120 This is the core hypercall routine: where the Guest gets what it wants.
- * Or gets killed.  Or, in the case of LHCALL_SHUTDOWN, both. */
+/*H:120
+ * This is the core hypercall routine: where the Guest gets what it wants.
+ * Or gets killed.  Or, in the case of LHCALL_SHUTDOWN, both.
+ */
 static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args)
 {
 	switch (args->arg0) {
 	case LHCALL_FLUSH_ASYNC:
-		/* This call does nothing, except by breaking out of the Guest
-		 * it makes us process all the asynchronous hypercalls. */
+		/*
+		 * This call does nothing, except by breaking out of the Guest
+		 * it makes us process all the asynchronous hypercalls.
+		 */
 		break;
 	case LHCALL_SEND_INTERRUPTS:
-		/* This call does nothing too, but by breaking out of the Guest
-		 * it makes us process any pending interrupts. */
+		/*
+		 * This call does nothing too, but by breaking out of the Guest
+		 * it makes us process any pending interrupts.
+		 */
 		break;
 	case LHCALL_LGUEST_INIT:
-		/* You can't get here unless you're already initialized.  Don't
-		 * do that. */
+		/*
+		 * You can't get here unless you're already initialized.  Don't
+		 * do that.
+		 */
 		kill_guest(cpu, "already have lguest_data");
 		break;
 	case LHCALL_SHUTDOWN: {
-		/* Shutdown is such a trivial hypercall that we do it in four
-		 * lines right here. */
 		char msg[128];
-		/* If the lgread fails, it will call kill_guest() itself; the
-		 * kill_guest() with the message will be ignored. */
+		/*
+		 * Shutdown is such a trivial hypercall that we do it in four
+		 * lines right here.
+		 *
+		 * If the lgread fails, it will call kill_guest() itself; the
+		 * kill_guest() with the message will be ignored.
+		 */
 		__lgread(cpu, msg, args->arg1, sizeof(msg));
 		msg[sizeof(msg)-1] = '\0';
 		kill_guest(cpu, "CRASH: %s", msg);
@@ -60,16 +73,17 @@ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args)
 		break;
 	}
 	case LHCALL_FLUSH_TLB:
-		/* FLUSH_TLB comes in two flavors, depending on the
-		 * argument: */
+		/* FLUSH_TLB comes in two flavors, depending on the argument: */
 		if (args->arg1)
 			guest_pagetable_clear_all(cpu);
 		else
 			guest_pagetable_flush_user(cpu);
 		break;
 
-	/* All these calls simply pass the arguments through to the right
-	 * routines. */
+	/*
+	 * All these calls simply pass the arguments through to the right
+	 * routines.
+	 */
 	case LHCALL_NEW_PGTABLE:
 		guest_new_pagetable(cpu, args->arg1);
 		break;
@@ -112,15 +126,16 @@ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args)
 			kill_guest(cpu, "Bad hypercall %li\n", args->arg0);
 	}
 }
-/*:*/
 
-/*H:124 Asynchronous hypercalls are easy: we just look in the array in the
+/*H:124
+ * Asynchronous hypercalls are easy: we just look in the array in the
  * Guest's "struct lguest_data" to see if any new ones are marked "ready".
  *
  * We are careful to do these in order: obviously we respect the order the
  * Guest put them in the ring, but we also promise the Guest that they will
  * happen before any normal hypercall (which is why we check this before
- * checking for a normal hcall). */
+ * checking for a normal hcall).
+ */
 static void do_async_hcalls(struct lg_cpu *cpu)
 {
 	unsigned int i;
@@ -133,22 +148,28 @@ static void do_async_hcalls(struct lg_cpu *cpu)
 	/* We process "struct lguest_data"s hcalls[] ring once. */
 	for (i = 0; i < ARRAY_SIZE(st); i++) {
 		struct hcall_args args;
-		/* We remember where we were up to from last time.  This makes
+		/*
+		 * We remember where we were up to from last time.  This makes
 		 * sure that the hypercalls are done in the order the Guest
-		 * places them in the ring. */
+		 * places them in the ring.
+		 */
 		unsigned int n = cpu->next_hcall;
 
 		/* 0xFF means there's no call here (yet). */
 		if (st[n] == 0xFF)
 			break;
 
-		/* OK, we have hypercall.  Increment the "next_hcall" cursor,
-		 * and wrap back to 0 if we reach the end. */
+		/*
+		 * OK, we have hypercall.  Increment the "next_hcall" cursor,
+		 * and wrap back to 0 if we reach the end.
+		 */
 		if (++cpu->next_hcall == LHCALL_RING_SIZE)
 			cpu->next_hcall = 0;
 
-		/* Copy the hypercall arguments into a local copy of
-		 * the hcall_args struct. */
+		/*
+		 * Copy the hypercall arguments into a local copy of the
+		 * hcall_args struct.
+		 */
 		if (copy_from_user(&args, &cpu->lg->lguest_data->hcalls[n],
 				   sizeof(struct hcall_args))) {
 			kill_guest(cpu, "Fetching async hypercalls");
@@ -164,19 +185,25 @@ static void do_async_hcalls(struct lg_cpu *cpu)
 			break;
 		}
 
-		/* Stop doing hypercalls if they want to notify the Launcher:
-		 * it needs to service this first. */
+		/*
+		 * Stop doing hypercalls if they want to notify the Launcher:
+		 * it needs to service this first.
+		 */
 		if (cpu->pending_notify)
 			break;
 	}
 }
 
-/* Last of all, we look at what happens first of all.  The very first time the
- * Guest makes a hypercall, we end up here to set things up: */
+/*
+ * Last of all, we look at what happens first of all.  The very first time the
+ * Guest makes a hypercall, we end up here to set things up:
+ */
 static void initialize(struct lg_cpu *cpu)
 {
-	/* You can't do anything until you're initialized.  The Guest knows the
-	 * rules, so we're unforgiving here. */
+	/*
+	 * You can't do anything until you're initialized.  The Guest knows the
+	 * rules, so we're unforgiving here.
+	 */
 	if (cpu->hcall->arg0 != LHCALL_LGUEST_INIT) {
 		kill_guest(cpu, "hypercall %li before INIT", cpu->hcall->arg0);
 		return;
@@ -185,32 +212,40 @@ static void initialize(struct lg_cpu *cpu)
 	if (lguest_arch_init_hypercalls(cpu))
 		kill_guest(cpu, "bad guest page %p", cpu->lg->lguest_data);
 
-	/* The Guest tells us where we're not to deliver interrupts by putting
-	 * the range of addresses into "struct lguest_data". */
+	/*
+	 * The Guest tells us where we're not to deliver interrupts by putting
+	 * the range of addresses into "struct lguest_data".
+	 */
 	if (get_user(cpu->lg->noirq_start, &cpu->lg->lguest_data->noirq_start)
 	    || get_user(cpu->lg->noirq_end, &cpu->lg->lguest_data->noirq_end))
 		kill_guest(cpu, "bad guest page %p", cpu->lg->lguest_data);
 
-	/* We write the current time into the Guest's data page once so it can
-	 * set its clock. */
+	/*
+	 * We write the current time into the Guest's data page once so it can
+	 * set its clock.
+	 */
 	write_timestamp(cpu);
 
 	/* page_tables.c will also do some setup. */
 	page_table_guest_data_init(cpu);
 
-	/* This is the one case where the above accesses might have been the
+	/*
+	 * This is the one case where the above accesses might have been the
 	 * first write to a Guest page.  This may have caused a copy-on-write
 	 * fault, but the old page might be (read-only) in the Guest
-	 * pagetable. */
+	 * pagetable.
+	 */
 	guest_pagetable_clear_all(cpu);
 }
 /*:*/
 
-/*M:013 If a Guest reads from a page (so creates a mapping) that it has never
+/*M:013
+ * If a Guest reads from a page (so creates a mapping) that it has never
  * written to, and then the Launcher writes to it (ie. the output of a virtual
  * device), the Guest will still see the old page.  In practice, this never
  * happens: why would the Guest read a page which it has never written to?  But
- * a similar scenario might one day bite us, so it's worth mentioning. :*/
+ * a similar scenario might one day bite us, so it's worth mentioning.
+:*/
 
 /*H:100
  * Hypercalls
@@ -229,17 +264,22 @@ void do_hypercalls(struct lg_cpu *cpu)
 		return;
 	}
 
-	/* The Guest has initialized.
+	/*
+	 * The Guest has initialized.
 	 *
-	 * Look in the hypercall ring for the async hypercalls: */
+	 * Look in the hypercall ring for the async hypercalls:
+	 */
 	do_async_hcalls(cpu);
 
-	/* If we stopped reading the hypercall ring because the Guest did a
+	/*
+	 * If we stopped reading the hypercall ring because the Guest did a
 	 * NOTIFY to the Launcher, we want to return now.  Otherwise we do
-	 * the hypercall. */
+	 * the hypercall.
+	 */
 	if (!cpu->pending_notify) {
 		do_hcall(cpu, cpu->hcall);
-		/* Tricky point: we reset the hcall pointer to mark the
+		/*
+		 * Tricky point: we reset the hcall pointer to mark the
 		 * hypercall as "done".  We use the hcall pointer rather than
 		 * the trap number to indicate a hypercall is pending.
 		 * Normally it doesn't matter: the Guest will run again and
@@ -248,13 +288,16 @@ void do_hypercalls(struct lg_cpu *cpu)
 		 * However, if we are signalled or the Guest sends I/O to the
 		 * Launcher, the run_guest() loop will exit without running the
 		 * Guest.  When it comes back it would try to re-run the
-		 * hypercall.  Finding that bug sucked. */
+		 * hypercall.  Finding that bug sucked.
+		 */
 		cpu->hcall = NULL;
 	}
 }
 
-/* This routine supplies the Guest with time: it's used for wallclock time at
- * initial boot and as a rough time source if the TSC isn't available. */
+/*
+ * This routine supplies the Guest with time: it's used for wallclock time at
+ * initial boot and as a rough time source if the TSC isn't available.
+ */
 void write_timestamp(struct lg_cpu *cpu)
 {
 	struct timespec now;
diff --git a/drivers/lguest/interrupts_and_traps.c b/drivers/lguest/interrupts_and_traps.c
index 0e9067b0d50..18648180db0 100644
--- a/drivers/lguest/interrupts_and_traps.c
+++ b/drivers/lguest/interrupts_and_traps.c
@@ -1,4 +1,5 @@
-/*P:800 Interrupts (traps) are complicated enough to earn their own file.
+/*P:800
+ * Interrupts (traps) are complicated enough to earn their own file.
  * There are three classes of interrupts:
  *
  * 1) Real hardware interrupts which occur while we're running the Guest,
@@ -10,7 +11,8 @@
  * just like real hardware would deliver them.  Traps from the Guest can be set
  * up to go directly back into the Guest, but sometimes the Host wants to see
  * them first, so we also have a way of "reflecting" them into the Guest as if
- * they had been delivered to it directly. :*/
+ * they had been delivered to it directly.
+:*/
 #include <linux/uaccess.h>
 #include <linux/interrupt.h>
 #include <linux/module.h>
@@ -26,8 +28,10 @@ static unsigned long idt_address(u32 lo, u32 hi)
 	return (lo & 0x0000FFFF) | (hi & 0xFFFF0000);
 }
 
-/* The "type" of the interrupt handler is a 4 bit field: we only support a
- * couple of types. */
+/*
+ * The "type" of the interrupt handler is a 4 bit field: we only support a
+ * couple of types.
+ */
 static int idt_type(u32 lo, u32 hi)
 {
 	return (hi >> 8) & 0xF;
@@ -39,8 +43,10 @@ static bool idt_present(u32 lo, u32 hi)
 	return (hi & 0x8000);
 }
 
-/* We need a helper to "push" a value onto the Guest's stack, since that's a
- * big part of what delivering an interrupt does. */
+/*
+ * We need a helper to "push" a value onto the Guest's stack, since that's a
+ * big part of what delivering an interrupt does.
+ */
 static void push_guest_stack(struct lg_cpu *cpu, unsigned long *gstack, u32 val)
 {
 	/* Stack grows upwards: move stack then write value. */
@@ -48,7 +54,8 @@ static void push_guest_stack(struct lg_cpu *cpu, unsigned long *gstack, u32 val)
 	lgwrite(cpu, *gstack, u32, val);
 }
 
-/*H:210 The set_guest_interrupt() routine actually delivers the interrupt or
+/*H:210
+ * The set_guest_interrupt() routine actually delivers the interrupt or
  * trap.  The mechanics of delivering traps and interrupts to the Guest are the
  * same, except some traps have an "error code" which gets pushed onto the
  * stack as well: the caller tells us if this is one.
@@ -59,7 +66,8 @@ static void push_guest_stack(struct lg_cpu *cpu, unsigned long *gstack, u32 val)
  *
  * We set up the stack just like the CPU does for a real interrupt, so it's
  * identical for the Guest (and the standard "iret" instruction will undo
- * it). */
+ * it).
+ */
 static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi,
 				bool has_err)
 {
@@ -67,20 +75,26 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi,
 	u32 eflags, ss, irq_enable;
 	unsigned long virtstack;
 
-	/* There are two cases for interrupts: one where the Guest is already
+	/*
+	 * There are two cases for interrupts: one where the Guest is already
 	 * in the kernel, and a more complex one where the Guest is in
-	 * userspace.  We check the privilege level to find out. */
+	 * userspace.  We check the privilege level to find out.
+	 */
 	if ((cpu->regs->ss&0x3) != GUEST_PL) {
-		/* The Guest told us their kernel stack with the SET_STACK
-		 * hypercall: both the virtual address and the segment */
+		/*
+		 * The Guest told us their kernel stack with the SET_STACK
+		 * hypercall: both the virtual address and the segment.
+		 */
 		virtstack = cpu->esp1;
 		ss = cpu->ss1;
 
 		origstack = gstack = guest_pa(cpu, virtstack);
-		/* We push the old stack segment and pointer onto the new
+		/*
+		 * We push the old stack segment and pointer onto the new
 		 * stack: when the Guest does an "iret" back from the interrupt
 		 * handler the CPU will notice they're dropping privilege
-		 * levels and expect these here. */
+		 * levels and expect these here.
+		 */
 		push_guest_stack(cpu, &gstack, cpu->regs->ss);
 		push_guest_stack(cpu, &gstack, cpu->regs->esp);
 	} else {
@@ -91,18 +105,22 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi,
 		origstack = gstack = guest_pa(cpu, virtstack);
 	}
 
-	/* Remember that we never let the Guest actually disable interrupts, so
+	/*
+	 * Remember that we never let the Guest actually disable interrupts, so
 	 * the "Interrupt Flag" bit is always set.  We copy that bit from the
 	 * Guest's "irq_enabled" field into the eflags word: we saw the Guest
-	 * copy it back in "lguest_iret". */
+	 * copy it back in "lguest_iret".
+	 */
 	eflags = cpu->regs->eflags;
 	if (get_user(irq_enable, &cpu->lg->lguest_data->irq_enabled) == 0
 	    && !(irq_enable & X86_EFLAGS_IF))
 		eflags &= ~X86_EFLAGS_IF;
 
-	/* An interrupt is expected to push three things on the stack: the old
+	/*
+	 * An interrupt is expected to push three things on the stack: the old
 	 * "eflags" word, the old code segment, and the old instruction
-	 * pointer. */
+	 * pointer.
+	 */
 	push_guest_stack(cpu, &gstack, eflags);
 	push_guest_stack(cpu, &gstack, cpu->regs->cs);
 	push_guest_stack(cpu, &gstack, cpu->regs->eip);
@@ -111,15 +129,19 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi,
 	if (has_err)
 		push_guest_stack(cpu, &gstack, cpu->regs->errcode);
 
-	/* Now we've pushed all the old state, we change the stack, the code
-	 * segment and the address to execute. */
+	/*
+	 * Now we've pushed all the old state, we change the stack, the code
+	 * segment and the address to execute.
+	 */
 	cpu->regs->ss = ss;
 	cpu->regs->esp = virtstack + (gstack - origstack);
 	cpu->regs->cs = (__KERNEL_CS|GUEST_PL);
 	cpu->regs->eip = idt_address(lo, hi);
 
-	/* There are two kinds of interrupt handlers: 0xE is an "interrupt
-	 * gate" which expects interrupts to be disabled on entry. */
+	/*
+	 * There are two kinds of interrupt handlers: 0xE is an "interrupt
+	 * gate" which expects interrupts to be disabled on entry.
+	 */
 	if (idt_type(lo, hi) == 0xE)
 		if (put_user(0, &cpu->lg->lguest_data->irq_enabled))
 			kill_guest(cpu, "Disabling interrupts");
@@ -130,7 +152,8 @@ static void set_guest_interrupt(struct lg_cpu *cpu, u32 lo, u32 hi,
  *
  * interrupt_pending() returns the first pending interrupt which isn't blocked
  * by the Guest.  It is called before every entry to the Guest, and just before
- * we go to sleep when the Guest has halted itself. */
+ * we go to sleep when the Guest has halted itself.
+ */
 unsigned int interrupt_pending(struct lg_cpu *cpu, bool *more)
 {
 	unsigned int irq;
@@ -140,8 +163,10 @@ unsigned int interrupt_pending(struct lg_cpu *cpu, bool *more)
 	if (!cpu->lg->lguest_data)
 		return LGUEST_IRQS;
 
-	/* Take our "irqs_pending" array and remove any interrupts the Guest
-	 * wants blocked: the result ends up in "blk". */
+	/*
+	 * Take our "irqs_pending" array and remove any interrupts the Guest
+	 * wants blocked: the result ends up in "blk".
+	 */
 	if (copy_from_user(&blk, cpu->lg->lguest_data->blocked_interrupts,
 			   sizeof(blk)))
 		return LGUEST_IRQS;
@@ -154,16 +179,20 @@ unsigned int interrupt_pending(struct lg_cpu *cpu, bool *more)
 	return irq;
 }
 
-/* This actually diverts the Guest to running an interrupt handler, once an
- * interrupt has been identified by interrupt_pending(). */
+/*
+ * This actually diverts the Guest to running an interrupt handler, once an
+ * interrupt has been identified by interrupt_pending().
+ */
 void try_deliver_interrupt(struct lg_cpu *cpu, unsigned int irq, bool more)
 {
 	struct desc_struct *idt;
 
 	BUG_ON(irq >= LGUEST_IRQS);
 
-	/* They may be in the middle of an iret, where they asked us never to
-	 * deliver interrupts. */
+	/*
+	 * They may be in the middle of an iret, where they asked us never to
+	 * deliver interrupts.
+	 */
 	if (cpu->regs->eip >= cpu->lg->noirq_start &&
 	   (cpu->regs->eip < cpu->lg->noirq_end))
 		return;
@@ -187,29 +216,37 @@ void try_deliver_interrupt(struct lg_cpu *cpu, unsigned int irq, bool more)
 		}
 	}
 
-	/* Look at the IDT entry the Guest gave us for this interrupt.  The
+	/*
+	 * Look at the IDT entry the Guest gave us for this interrupt.  The
 	 * first 32 (FIRST_EXTERNAL_VECTOR) entries are for traps, so we skip
-	 * over them. */
+	 * over them.
+	 */
 	idt = &cpu->arch.idt[FIRST_EXTERNAL_VECTOR+irq];
 	/* If they don't have a handler (yet?), we just ignore it */
 	if (idt_present(idt->a, idt->b)) {
 		/* OK, mark it no longer pending and deliver it. */
 		clear_bit(irq, cpu->irqs_pending);
-		/* set_guest_interrupt() takes the interrupt descriptor and a
+		/*
+		 * set_guest_interrupt() takes the interrupt descriptor and a
 		 * flag to say whether this interrupt pushes an error code onto
-		 * the stack as well: virtual interrupts never do. */
+		 * the stack as well: virtual interrupts never do.
+		 */
 		set_guest_interrupt(cpu, idt->a, idt->b, false);
 	}
 
-	/* Every time we deliver an interrupt, we update the timestamp in the
+	/*
+	 * Every time we deliver an interrupt, we update the timestamp in the
 	 * Guest's lguest_data struct.  It would be better for the Guest if we
 	 * did this more often, but it can actually be quite slow: doing it
 	 * here is a compromise which means at least it gets updated every
-	 * timer interrupt. */
+	 * timer interrupt.
+	 */
 	write_timestamp(cpu);
 
-	/* If there are no other interrupts we want to deliver, clear
-	 * the pending flag. */
+	/*
+	 * If there are no other interrupts we want to deliver, clear
+	 * the pending flag.
+	 */
 	if (!more)
 		put_user(0, &cpu->lg->lguest_data->irq_pending);
 }
@@ -217,24 +254,29 @@ void try_deliver_interrupt(struct lg_cpu *cpu, unsigned int irq, bool more)
 /* And this is the routine when we want to set an interrupt for the Guest. */
 void set_interrupt(struct lg_cpu *cpu, unsigned int irq)
 {
-	/* Next time the Guest runs, the core code will see if it can deliver
-	 * this interrupt. */
+	/*
+	 * Next time the Guest runs, the core code will see if it can deliver
+	 * this interrupt.
+	 */
 	set_bit(irq, cpu->irqs_pending);
 
-	/* Make sure it sees it; it might be asleep (eg. halted), or
-	 * running the Guest right now, in which case kick_process()
-	 * will knock it out. */
+	/*
+	 * Make sure it sees it; it might be asleep (eg. halted), or running
+	 * the Guest right now, in which case kick_process() will knock it out.
+	 */
 	if (!wake_up_process(cpu->tsk))
 		kick_process(cpu->tsk);
 }
 /*:*/
 
-/* Linux uses trap 128 for system calls.  Plan9 uses 64, and Ron Minnich sent
+/*
+ * Linux uses trap 128 for system calls.  Plan9 uses 64, and Ron Minnich sent
  * me a patch, so we support that too.  It'd be a big step for lguest if half
  * the Plan 9 user base were to start using it.
  *
  * Actually now I think of it, it's possible that Ron *is* half the Plan 9
- * userbase.  Oh well. */
+ * userbase.  Oh well.
+ */
 static bool could_be_syscall(unsigned int num)
 {
 	/* Normal Linux SYSCALL_VECTOR or reserved vector? */
@@ -274,9 +316,11 @@ void free_interrupts(void)
 		clear_bit(syscall_vector, used_vectors);
 }
 
-/*H:220 Now we've got the routines to deliver interrupts, delivering traps like
+/*H:220
+ * Now we've got the routines to deliver interrupts, delivering traps like
  * page fault is easy.  The only trick is that Intel decided that some traps
- * should have error codes: */
+ * should have error codes:
+ */
 static bool has_err(unsigned int trap)
 {
 	return (trap == 8 || (trap >= 10 && trap <= 14) || trap == 17);
@@ -285,13 +329,17 @@ static bool has_err(unsigned int trap)
 /* deliver_trap() returns true if it could deliver the trap. */
 bool deliver_trap(struct lg_cpu *cpu, unsigned int num)
 {
-	/* Trap numbers are always 8 bit, but we set an impossible trap number
-	 * for traps inside the Switcher, so check that here. */
+	/*
+	 * Trap numbers are always 8 bit, but we set an impossible trap number
+	 * for traps inside the Switcher, so check that here.
+	 */
 	if (num >= ARRAY_SIZE(cpu->arch.idt))
 		return false;
 
-	/* Early on the Guest hasn't set the IDT entries (or maybe it put a
-	 * bogus one in): if we fail here, the Guest will be killed. */
+	/*
+	 * Early on the Guest hasn't set the IDT entries (or maybe it put a
+	 * bogus one in): if we fail here, the Guest will be killed.
+	 */
 	if (!idt_present(cpu->arch.idt[num].a, cpu->arch.idt[num].b))
 		return false;
 	set_guest_interrupt(cpu, cpu->arch.idt[num].a,
@@ -299,7 +347,8 @@ bool deliver_trap(struct lg_cpu *cpu, unsigned int num)
 	return true;
 }
 
-/*H:250 Here's the hard part: returning to the Host every time a trap happens
+/*H:250
+ * Here's the hard part: returning to the Host every time a trap happens
  * and then calling deliver_trap() and re-entering the Guest is slow.
  * Particularly because Guest userspace system calls are traps (usually trap
  * 128).
@@ -311,69 +360,87 @@ bool deliver_trap(struct lg_cpu *cpu, unsigned int num)
  * the other hypervisors would beat it up at lunchtime.
  *
  * This routine indicates if a particular trap number could be delivered
- * directly. */
+ * directly.
+ */
 static bool direct_trap(unsigned int num)
 {
-	/* Hardware interrupts don't go to the Guest at all (except system
-	 * call). */
+	/*
+	 * Hardware interrupts don't go to the Guest at all (except system
+	 * call).
+	 */
 	if (num >= FIRST_EXTERNAL_VECTOR && !could_be_syscall(num))
 		return false;
 
-	/* The Host needs to see page faults (for shadow paging and to save the
+	/*
+	 * The Host needs to see page faults (for shadow paging and to save the
 	 * fault address), general protection faults (in/out emulation) and
 	 * device not available (TS handling), invalid opcode fault (kvm hcall),
-	 * and of course, the hypercall trap. */
+	 * and of course, the hypercall trap.
+	 */
 	return num != 14 && num != 13 && num != 7 &&
 			num != 6 && num != LGUEST_TRAP_ENTRY;
 }
 /*:*/
 
-/*M:005 The Guest has the ability to turn its interrupt gates into trap gates,
+/*M:005
+ * The Guest has the ability to turn its interrupt gates into trap gates,
  * if it is careful.  The Host will let trap gates can go directly to the
  * Guest, but the Guest needs the interrupts atomically disabled for an
  * interrupt gate.  It can do this by pointing the trap gate at instructions
- * within noirq_start and noirq_end, where it can safely disable interrupts. */
+ * within noirq_start and noirq_end, where it can safely disable interrupts.
+ */
 
-/*M:006 The Guests do not use the sysenter (fast system call) instruction,
+/*M:006
+ * The Guests do not use the sysenter (fast system call) instruction,
  * because it's hardcoded to enter privilege level 0 and so can't go direct.
  * It's about twice as fast as the older "int 0x80" system call, so it might
  * still be worthwhile to handle it in the Switcher and lcall down to the
  * Guest.  The sysenter semantics are hairy tho: search for that keyword in
- * entry.S :*/
+ * entry.S
+:*/
 
-/*H:260 When we make traps go directly into the Guest, we need to make sure
+/*H:260
+ * When we make traps go directly into the Guest, we need to make sure
  * the kernel stack is valid (ie. mapped in the page tables).  Otherwise, the
  * CPU trying to deliver the trap will fault while trying to push the interrupt
  * words on the stack: this is called a double fault, and it forces us to kill
  * the Guest.
  *
- * Which is deeply unfair, because (literally!) it wasn't the Guests' fault. */
+ * Which is deeply unfair, because (literally!) it wasn't the Guests' fault.
+ */
 void pin_stack_pages(struct lg_cpu *cpu)
 {
 	unsigned int i;
 
-	/* Depending on the CONFIG_4KSTACKS option, the Guest can have one or
-	 * two pages of stack space. */
+	/*
+	 * Depending on the CONFIG_4KSTACKS option, the Guest can have one or
+	 * two pages of stack space.
+	 */
 	for (i = 0; i < cpu->lg->stack_pages; i++)
-		/* The stack grows *upwards*, so the address we're given is the
+		/*
+		 * The stack grows *upwards*, so the address we're given is the
 		 * start of the page after the kernel stack.  Subtract one to
 		 * get back onto the first stack page, and keep subtracting to
-		 * get to the rest of the stack pages. */
+		 * get to the rest of the stack pages.
+		 */
 		pin_page(cpu, cpu->esp1 - 1 - i * PAGE_SIZE);
 }
 
-/* Direct traps also mean that we need to know whenever the Guest wants to use
+/*
+ * Direct traps also mean that we need to know whenever the Guest wants to use
  * a different kernel stack, so we can change the IDT entries to use that
  * stack.  The IDT entries expect a virtual address, so unlike most addresses
  * the Guest gives us, the "esp" (stack pointer) value here is virtual, not
  * physical.
  *
  * In Linux each process has its own kernel stack, so this happens a lot: we
- * change stacks on each context switch. */
+ * change stacks on each context switch.
+ */
 void guest_set_stack(struct lg_cpu *cpu, u32 seg, u32 esp, unsigned int pages)
 {
-	/* You are not allowed have a stack segment with privilege level 0: bad
-	 * Guest! */
+	/*
+	 * You're not allowed a stack segment with privilege level 0: bad Guest!
+	 */
 	if ((seg & 0x3) != GUEST_PL)
 		kill_guest(cpu, "bad stack segment %i", seg);
 	/* We only expect one or two stack pages. */
@@ -387,11 +454,15 @@ void guest_set_stack(struct lg_cpu *cpu, u32 seg, u32 esp, unsigned int pages)
 	pin_stack_pages(cpu);
 }
 
-/* All this reference to mapping stacks leads us neatly into the other complex
- * part of the Host: page table handling. */
+/*
+ * All this reference to mapping stacks leads us neatly into the other complex
+ * part of the Host: page table handling.
+ */
 
-/*H:235 This is the routine which actually checks the Guest's IDT entry and
- * transfers it into the entry in "struct lguest": */
+/*H:235
+ * This is the routine which actually checks the Guest's IDT entry and
+ * transfers it into the entry in "struct lguest":
+ */
 static void set_trap(struct lg_cpu *cpu, struct desc_struct *trap,
 		     unsigned int num, u32 lo, u32 hi)
 {
@@ -407,30 +478,38 @@ static void set_trap(struct lg_cpu *cpu, struct desc_struct *trap,
 	if (type != 0xE && type != 0xF)
 		kill_guest(cpu, "bad IDT type %i", type);
 
-	/* We only copy the handler address, present bit, privilege level and
+	/*
+	 * We only copy the handler address, present bit, privilege level and
 	 * type.  The privilege level controls where the trap can be triggered
 	 * manually with an "int" instruction.  This is usually GUEST_PL,
-	 * except for system calls which userspace can use. */
+	 * except for system calls which userspace can use.
+	 */
 	trap->a = ((__KERNEL_CS|GUEST_PL)<<16) | (lo&0x0000FFFF);
 	trap->b = (hi&0xFFFFEF00);
 }
 
-/*H:230 While we're here, dealing with delivering traps and interrupts to the
+/*H:230
+ * While we're here, dealing with delivering traps and interrupts to the
  * Guest, we might as well complete the picture: how the Guest tells us where
  * it wants them to go.  This would be simple, except making traps fast
  * requires some tricks.
  *
  * We saw the Guest setting Interrupt Descriptor Table (IDT) entries with the
- * LHCALL_LOAD_IDT_ENTRY hypercall before: that comes here. */
+ * LHCALL_LOAD_IDT_ENTRY hypercall before: that comes here.
+ */
 void load_guest_idt_entry(struct lg_cpu *cpu, unsigned int num, u32 lo, u32 hi)
 {
-	/* Guest never handles: NMI, doublefault, spurious interrupt or
-	 * hypercall.  We ignore when it tries to set them. */
+	/*
+	 * Guest never handles: NMI, doublefault, spurious interrupt or
+	 * hypercall.  We ignore when it tries to set them.
+	 */
 	if (num == 2 || num == 8 || num == 15 || num == LGUEST_TRAP_ENTRY)
 		return;
 
-	/* Mark the IDT as changed: next time the Guest runs we'll know we have
-	 * to copy this again. */
+	/*
+	 * Mark the IDT as changed: next time the Guest runs we'll know we have
+	 * to copy this again.
+	 */
 	cpu->changed |= CHANGED_IDT;
 
 	/* Check that the Guest doesn't try to step outside the bounds. */
@@ -440,9 +519,11 @@ void load_guest_idt_entry(struct lg_cpu *cpu, unsigned int num, u32 lo, u32 hi)
 		set_trap(cpu, &cpu->arch.idt[num], num, lo, hi);
 }
 
-/* The default entry for each interrupt points into the Switcher routines which
+/*
+ * The default entry for each interrupt points into the Switcher routines which
  * simply return to the Host.  The run_guest() loop will then call
- * deliver_trap() to bounce it back into the Guest. */
+ * deliver_trap() to bounce it back into the Guest.
+ */
 static void default_idt_entry(struct desc_struct *idt,
 			      int trap,
 			      const unsigned long handler,
@@ -451,13 +532,17 @@ static void default_idt_entry(struct desc_struct *idt,
 	/* A present interrupt gate. */
 	u32 flags = 0x8e00;
 
-	/* Set the privilege level on the entry for the hypercall: this allows
-	 * the Guest to use the "int" instruction to trigger it. */
+	/*
+	 * Set the privilege level on the entry for the hypercall: this allows
+	 * the Guest to use the "int" instruction to trigger it.
+	 */
 	if (trap == LGUEST_TRAP_ENTRY)
 		flags |= (GUEST_PL << 13);
 	else if (base)
-		/* Copy priv. level from what Guest asked for.  This allows
-		 * debug (int 3) traps from Guest userspace, for example. */
+		/*
+		 * Copy privilege level from what Guest asked for.  This allows
+		 * debug (int 3) traps from Guest userspace, for example.
+		 */
 		flags |= (base->b & 0x6000);
 
 	/* Now pack it into the IDT entry in its weird format. */
@@ -475,16 +560,20 @@ void setup_default_idt_entries(struct lguest_ro_state *state,
 		default_idt_entry(&state->guest_idt[i], i, def[i], NULL);
 }
 
-/*H:240 We don't use the IDT entries in the "struct lguest" directly, instead
+/*H:240
+ * We don't use the IDT entries in the "struct lguest" directly, instead
  * we copy them into the IDT which we've set up for Guests on this CPU, just
- * before we run the Guest.  This routine does that copy. */
+ * before we run the Guest.  This routine does that copy.
+ */
 void copy_traps(const struct lg_cpu *cpu, struct desc_struct *idt,
 		const unsigned long *def)
 {
 	unsigned int i;
 
-	/* We can simply copy the direct traps, otherwise we use the default
-	 * ones in the Switcher: they will return to the Host. */
+	/*
+	 * We can simply copy the direct traps, otherwise we use the default
+	 * ones in the Switcher: they will return to the Host.
+	 */
 	for (i = 0; i < ARRAY_SIZE(cpu->arch.idt); i++) {
 		const struct desc_struct *gidt = &cpu->arch.idt[i];
 
@@ -492,14 +581,16 @@ void copy_traps(const struct lg_cpu *cpu, struct desc_struct *idt,
 		if (!direct_trap(i))
 			continue;
 
-		/* Only trap gates (type 15) can go direct to the Guest.
+		/*
+		 * Only trap gates (type 15) can go direct to the Guest.
 		 * Interrupt gates (type 14) disable interrupts as they are
 		 * entered, which we never let the Guest do.  Not present
 		 * entries (type 0x0) also can't go direct, of course.
 		 *
 		 * If it can't go direct, we still need to copy the priv. level:
 		 * they might want to give userspace access to a software
-		 * interrupt. */
+		 * interrupt.
+		 */
 		if (idt_type(gidt->a, gidt->b) == 0xF)
 			idt[i] = *gidt;
 		else
@@ -518,7 +609,8 @@ void copy_traps(const struct lg_cpu *cpu, struct desc_struct *idt,
  * the next timer interrupt (in nanoseconds).  We use the high-resolution timer
  * infrastructure to set a callback at that time.
  *
- * 0 means "turn off the clock". */
+ * 0 means "turn off the clock".
+ */
 void guest_set_clockevent(struct lg_cpu *cpu, unsigned long delta)
 {
 	ktime_t expires;
@@ -529,9 +621,11 @@ void guest_set_clockevent(struct lg_cpu *cpu, unsigned long delta)
 		return;
 	}
 
-	/* We use wallclock time here, so the Guest might not be running for
+	/*
+	 * We use wallclock time here, so the Guest might not be running for
 	 * all the time between now and the timer interrupt it asked for.  This
-	 * is almost always the right thing to do. */
+	 * is almost always the right thing to do.
+	 */
 	expires = ktime_add_ns(ktime_get_real(), delta);
 	hrtimer_start(&cpu->hrt, expires, HRTIMER_MODE_ABS);
 }
diff --git a/drivers/lguest/lg.h b/drivers/lguest/lg.h
index 01c59192379..74c0db691b5 100644
--- a/drivers/lguest/lg.h
+++ b/drivers/lguest/lg.h
@@ -54,13 +54,13 @@ struct lg_cpu {
 
 	unsigned long pending_notify; /* pfn from LHCALL_NOTIFY */
 
-	/* At end of a page shared mapped over lguest_pages in guest.  */
+	/* At end of a page shared mapped over lguest_pages in guest. */
 	unsigned long regs_page;
 	struct lguest_regs *regs;
 
 	struct lguest_pages *last_pages;
 
-	int cpu_pgd; /* which pgd this cpu is currently using */
+	int cpu_pgd; /* Which pgd this cpu is currently using */
 
 	/* If a hypercall was asked for, this points to the arguments. */
 	struct hcall_args *hcall;
@@ -96,8 +96,11 @@ struct lguest
 	unsigned int nr_cpus;
 
 	u32 pfn_limit;
-	/* This provides the offset to the base of guest-physical
-	 * memory in the Launcher. */
+
+	/*
+	 * This provides the offset to the base of guest-physical memory in the
+	 * Launcher.
+	 */
 	void __user *mem_base;
 	unsigned long kernel_address;
 
@@ -122,11 +125,13 @@ bool lguest_address_ok(const struct lguest *lg,
 void __lgread(struct lg_cpu *, void *, unsigned long, unsigned);
 void __lgwrite(struct lg_cpu *, unsigned long, const void *, unsigned);
 
-/*H:035 Using memory-copy operations like that is usually inconvient, so we
+/*H:035
+ * Using memory-copy operations like that is usually inconvient, so we
  * have the following helper macros which read and write a specific type (often
  * an unsigned long).
  *
- * This reads into a variable of the given type then returns that. */
+ * This reads into a variable of the given type then returns that.
+ */
 #define lgread(cpu, addr, type)						\
 	({ type _v; __lgread((cpu), &_v, (addr), sizeof(_v)); _v; })
 
@@ -140,9 +145,11 @@ void __lgwrite(struct lg_cpu *, unsigned long, const void *, unsigned);
 
 int run_guest(struct lg_cpu *cpu, unsigned long __user *user);
 
-/* Helper macros to obtain the first 12 or the last 20 bits, this is only the
+/*
+ * Helper macros to obtain the first 12 or the last 20 bits, this is only the
  * first step in the migration to the kernel types.  pte_pfn is already defined
- * in the kernel. */
+ * in the kernel.
+ */
 #define pgd_flags(x)	(pgd_val(x) & ~PAGE_MASK)
 #define pgd_pfn(x)	(pgd_val(x) >> PAGE_SHIFT)
 #define pmd_flags(x)    (pmd_val(x) & ~PAGE_MASK)
diff --git a/drivers/lguest/lguest_device.c b/drivers/lguest/lguest_device.c
index e082cdac88b..cc000e79c3d 100644
--- a/drivers/lguest/lguest_device.c
+++ b/drivers/lguest/lguest_device.c
@@ -1,10 +1,12 @@
-/*P:050 Lguest guests use a very simple method to describe devices.  It's a
+/*P:050
+ * Lguest guests use a very simple method to describe devices.  It's a
  * series of device descriptors contained just above the top of normal Guest
  * memory.
  *
  * We use the standard "virtio" device infrastructure, which provides us with a
  * console, a network and a block driver.  Each one expects some configuration
- * information and a "virtqueue" or two to send and receive data. :*/
+ * information and a "virtqueue" or two to send and receive data.
+:*/
 #include <linux/init.h>
 #include <linux/bootmem.h>
 #include <linux/lguest_launcher.h>
@@ -20,8 +22,10 @@
 /* The pointer to our (page) of device descriptions. */
 static void *lguest_devices;
 
-/* For Guests, device memory can be used as normal memory, so we cast away the
- * __iomem to quieten sparse. */
+/*
+ * For Guests, device memory can be used as normal memory, so we cast away the
+ * __iomem to quieten sparse.
+ */
 static inline void *lguest_map(unsigned long phys_addr, unsigned long pages)
 {
 	return (__force void *)ioremap_cache(phys_addr, PAGE_SIZE*pages);
@@ -32,8 +36,10 @@ static inline void lguest_unmap(void *addr)
 	iounmap((__force void __iomem *)addr);
 }
 
-/*D:100 Each lguest device is just a virtio device plus a pointer to its entry
- * in the lguest_devices page. */
+/*D:100
+ * Each lguest device is just a virtio device plus a pointer to its entry
+ * in the lguest_devices page.
+ */
 struct lguest_device {
 	struct virtio_device vdev;
 
@@ -41,9 +47,11 @@ struct lguest_device {
 	struct lguest_device_desc *desc;
 };
 
-/* Since the virtio infrastructure hands us a pointer to the virtio_device all
+/*
+ * Since the virtio infrastructure hands us a pointer to the virtio_device all
  * the time, it helps to have a curt macro to get a pointer to the struct
- * lguest_device it's enclosed in.  */
+ * lguest_device it's enclosed in.
+ */
 #define to_lgdev(vd) container_of(vd, struct lguest_device, vdev)
 
 /*D:130
@@ -55,7 +63,8 @@ struct lguest_device {
  * the driver will look at them during setup.
  *
  * A convenient routine to return the device's virtqueue config array:
- * immediately after the descriptor. */
+ * immediately after the descriptor.
+ */
 static struct lguest_vqconfig *lg_vq(const struct lguest_device_desc *desc)
 {
 	return (void *)(desc + 1);
@@ -98,10 +107,12 @@ static u32 lg_get_features(struct virtio_device *vdev)
 	return features;
 }
 
-/* The virtio core takes the features the Host offers, and copies the
- * ones supported by the driver into the vdev->features array.  Once
- * that's all sorted out, this routine is called so we can tell the
- * Host which features we understand and accept. */
+/*
+ * The virtio core takes the features the Host offers, and copies the ones
+ * supported by the driver into the vdev->features array.  Once that's all
+ * sorted out, this routine is called so we can tell the Host which features we
+ * understand and accept.
+ */
 static void lg_finalize_features(struct virtio_device *vdev)
 {
 	unsigned int i, bits;
@@ -112,10 +123,11 @@ static void lg_finalize_features(struct virtio_device *vdev)
 	/* Give virtio_ring a chance to accept features. */
 	vring_transport_features(vdev);
 
-	/* The vdev->feature array is a Linux bitmask: this isn't the
-	 * same as a the simple array of bits used by lguest devices
-	 * for features.  So we do this slow, manual conversion which is
-	 * completely general. */
+	/*
+	 * The vdev->feature array is a Linux bitmask: this isn't the same as a
+	 * the simple array of bits used by lguest devices for features.  So we
+	 * do this slow, manual conversion which is completely general.
+	 */
 	memset(out_features, 0, desc->feature_len);
 	bits = min_t(unsigned, desc->feature_len, sizeof(vdev->features)) * 8;
 	for (i = 0; i < bits; i++) {
@@ -146,15 +158,19 @@ static void lg_set(struct virtio_device *vdev, unsigned int offset,
 	memcpy(lg_config(desc) + offset, buf, len);
 }
 
-/* The operations to get and set the status word just access the status field
- * of the device descriptor. */
+/*
+ * The operations to get and set the status word just access the status field
+ * of the device descriptor.
+ */
 static u8 lg_get_status(struct virtio_device *vdev)
 {
 	return to_lgdev(vdev)->desc->status;
 }
 
-/* To notify on status updates, we (ab)use the NOTIFY hypercall, with the
- * descriptor address of the device.  A zero status means "reset". */
+/*
+ * To notify on status updates, we (ab)use the NOTIFY hypercall, with the
+ * descriptor address of the device.  A zero status means "reset".
+ */
 static void set_status(struct virtio_device *vdev, u8 status)
 {
 	unsigned long offset = (void *)to_lgdev(vdev)->desc - lguest_devices;
@@ -200,13 +216,17 @@ struct lguest_vq_info
 	void *pages;
 };
 
-/* When the virtio_ring code wants to prod the Host, it calls us here and we
+/*
+ * When the virtio_ring code wants to prod the Host, it calls us here and we
  * make a hypercall.  We hand the physical address of the virtqueue so the Host
- * knows which virtqueue we're talking about. */
+ * knows which virtqueue we're talking about.
+ */
 static void lg_notify(struct virtqueue *vq)
 {
-	/* We store our virtqueue information in the "priv" pointer of the
-	 * virtqueue structure. */
+	/*
+	 * We store our virtqueue information in the "priv" pointer of the
+	 * virtqueue structure.
+	 */
 	struct lguest_vq_info *lvq = vq->priv;
 
 	kvm_hypercall1(LHCALL_NOTIFY, lvq->config.pfn << PAGE_SHIFT);
@@ -215,7 +235,8 @@ static void lg_notify(struct virtqueue *vq)
 /* An extern declaration inside a C file is bad form.  Don't do it. */
 extern void lguest_setup_irq(unsigned int irq);
 
-/* This routine finds the first virtqueue described in the configuration of
+/*
+ * This routine finds the first virtqueue described in the configuration of
  * this device and sets it up.
  *
  * This is kind of an ugly duckling.  It'd be nicer to have a standard
@@ -225,7 +246,8 @@ extern void lguest_setup_irq(unsigned int irq);
  * simpler for the Host to simply tell us where the pages are.
  *
  * So we provide drivers with a "find the Nth virtqueue and set it up"
- * function. */
+ * function.
+ */
 static struct virtqueue *lg_find_vq(struct virtio_device *vdev,
 				    unsigned index,
 				    void (*callback)(struct virtqueue *vq),
@@ -244,9 +266,11 @@ static struct virtqueue *lg_find_vq(struct virtio_device *vdev,
 	if (!lvq)
 		return ERR_PTR(-ENOMEM);
 
-	/* Make a copy of the "struct lguest_vqconfig" entry, which sits after
+	/*
+	 * Make a copy of the "struct lguest_vqconfig" entry, which sits after
 	 * the descriptor.  We need a copy because the config space might not
-	 * be aligned correctly. */
+	 * be aligned correctly.
+	 */
 	memcpy(&lvq->config, lg_vq(ldev->desc)+index, sizeof(lvq->config));
 
 	printk("Mapping virtqueue %i addr %lx\n", index,
@@ -261,8 +285,10 @@ static struct virtqueue *lg_find_vq(struct virtio_device *vdev,
 		goto free_lvq;
 	}
 
-	/* OK, tell virtio_ring.c to set up a virtqueue now we know its size
-	 * and we've got a pointer to its pages. */
+	/*
+	 * OK, tell virtio_ring.c to set up a virtqueue now we know its size
+	 * and we've got a pointer to its pages.
+	 */
 	vq = vring_new_virtqueue(lvq->config.num, LGUEST_VRING_ALIGN,
 				 vdev, lvq->pages, lg_notify, callback, name);
 	if (!vq) {
@@ -273,18 +299,23 @@ static struct virtqueue *lg_find_vq(struct virtio_device *vdev,
 	/* Make sure the interrupt is allocated. */
 	lguest_setup_irq(lvq->config.irq);
 
-	/* Tell the interrupt for this virtqueue to go to the virtio_ring
-	 * interrupt handler. */
-	/* FIXME: We used to have a flag for the Host to tell us we could use
+	/*
+	 * Tell the interrupt for this virtqueue to go to the virtio_ring
+	 * interrupt handler.
+	 *
+	 * FIXME: We used to have a flag for the Host to tell us we could use
 	 * the interrupt as a source of randomness: it'd be nice to have that
-	 * back.. */
+	 * back.
+	 */
 	err = request_irq(lvq->config.irq, vring_interrupt, IRQF_SHARED,
 			  dev_name(&vdev->dev), vq);
 	if (err)
 		goto destroy_vring;
 
-	/* Last of all we hook up our 'struct lguest_vq_info" to the
-	 * virtqueue's priv pointer. */
+	/*
+	 * Last of all we hook up our 'struct lguest_vq_info" to the
+	 * virtqueue's priv pointer.
+	 */
 	vq->priv = lvq;
 	return vq;
 
@@ -358,11 +389,14 @@ static struct virtio_config_ops lguest_config_ops = {
 	.del_vqs = lg_del_vqs,
 };
 
-/* The root device for the lguest virtio devices.  This makes them appear as
- * /sys/devices/lguest/0,1,2 not /sys/devices/0,1,2. */
+/*
+ * The root device for the lguest virtio devices.  This makes them appear as
+ * /sys/devices/lguest/0,1,2 not /sys/devices/0,1,2.
+ */
 static struct device *lguest_root;
 
-/*D:120 This is the core of the lguest bus: actually adding a new device.
+/*D:120
+ * This is the core of the lguest bus: actually adding a new device.
  * It's a separate function because it's neater that way, and because an
  * earlier version of the code supported hotplug and unplug.  They were removed
  * early on because they were never used.
@@ -371,14 +405,14 @@ static struct device *lguest_root;
  *
  * It's worth reading this carefully: we start with a pointer to the new device
  * descriptor in the "lguest_devices" page, and the offset into the device
- * descriptor page so we can uniquely identify it if things go badly wrong. */
+ * descriptor page so we can uniquely identify it if things go badly wrong.
+ */
 static void add_lguest_device(struct lguest_device_desc *d,
 			      unsigned int offset)
 {
 	struct lguest_device *ldev;
 
-	/* Start with zeroed memory; Linux's device layer seems to count on
-	 * it. */
+	/* Start with zeroed memory; Linux's device layer counts on it. */
 	ldev = kzalloc(sizeof(*ldev), GFP_KERNEL);
 	if (!ldev) {
 		printk(KERN_EMERG "Cannot allocate lguest dev %u type %u\n",
@@ -390,15 +424,19 @@ static void add_lguest_device(struct lguest_device_desc *d,
 	ldev->vdev.dev.parent = lguest_root;
 	/* We have a unique device index thanks to the dev_index counter. */
 	ldev->vdev.id.device = d->type;
-	/* We have a simple set of routines for querying the device's
-	 * configuration information and setting its status. */
+	/*
+	 * We have a simple set of routines for querying the device's
+	 * configuration information and setting its status.
+	 */
 	ldev->vdev.config = &lguest_config_ops;
 	/* And we remember the device's descriptor for lguest_config_ops. */
 	ldev->desc = d;
 
-	/* register_virtio_device() sets up the generic fields for the struct
+	/*
+	 * register_virtio_device() sets up the generic fields for the struct
 	 * virtio_device and calls device_register().  This makes the bus
-	 * infrastructure look for a matching driver. */
+	 * infrastructure look for a matching driver.
+	 */
 	if (register_virtio_device(&ldev->vdev) != 0) {
 		printk(KERN_ERR "Failed to register lguest dev %u type %u\n",
 		       offset, d->type);
@@ -406,8 +444,10 @@ static void add_lguest_device(struct lguest_device_desc *d,
 	}
 }
 
-/*D:110 scan_devices() simply iterates through the device page.  The type 0 is
- * reserved to mean "end of devices". */
+/*D:110
+ * scan_devices() simply iterates through the device page.  The type 0 is
+ * reserved to mean "end of devices".
+ */
 static void scan_devices(void)
 {
 	unsigned int i;
@@ -426,7 +466,8 @@ static void scan_devices(void)
 	}
 }
 
-/*D:105 Fairly early in boot, lguest_devices_init() is called to set up the
+/*D:105
+ * Fairly early in boot, lguest_devices_init() is called to set up the
  * lguest device infrastructure.  We check that we are a Guest by checking
  * pv_info.name: there are other ways of checking, but this seems most
  * obvious to me.
@@ -437,7 +478,8 @@ static void scan_devices(void)
  * correct sysfs incantation).
  *
  * Finally we call scan_devices() which adds all the devices found in the
- * lguest_devices page. */
+ * lguest_devices page.
+ */
 static int __init lguest_devices_init(void)
 {
 	if (strcmp(pv_info.name, "lguest") != 0)
@@ -456,11 +498,13 @@ static int __init lguest_devices_init(void)
 /* We do this after core stuff, but before the drivers. */
 postcore_initcall(lguest_devices_init);
 
-/*D:150 At this point in the journey we used to now wade through the lguest
+/*D:150
+ * At this point in the journey we used to now wade through the lguest
  * devices themselves: net, block and console.  Since they're all now virtio
  * devices rather than lguest-specific, I've decided to ignore them.  Mostly,
  * they're kind of boring.  But this does mean you'll never experience the
  * thrill of reading the forbidden love scene buried deep in the block driver.
  *
  * "make Launcher" beckons, where we answer questions like "Where do Guests
- * come from?", and "What do you do when someone asks for optimization?". */
+ * come from?", and "What do you do when someone asks for optimization?".
+ */
diff --git a/drivers/lguest/lguest_user.c b/drivers/lguest/lguest_user.c
index 407722a8e0c..7e92017103d 100644
--- a/drivers/lguest/lguest_user.c
+++ b/drivers/lguest/lguest_user.c
@@ -1,8 +1,10 @@
-/*P:200 This contains all the /dev/lguest code, whereby the userspace launcher
+/*P:200
+ * This contains all the /dev/lguest code, whereby the userspace launcher
  * controls and communicates with the Guest.  For example, the first write will
  * tell us the Guest's memory layout, pagetable, entry point and kernel address
  * offset.  A read will run the Guest until something happens, such as a signal
- * or the Guest doing a NOTIFY out to the Launcher. :*/
+ * or the Guest doing a NOTIFY out to the Launcher.
+:*/
 #include <linux/uaccess.h>
 #include <linux/miscdevice.h>
 #include <linux/fs.h>
@@ -37,8 +39,10 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd)
 	if (!addr)
 		return -EINVAL;
 
-	/* Replace the old array with the new one, carefully: others can
-	 * be accessing it at the same time */
+	/*
+	 * Replace the old array with the new one, carefully: others can
+	 * be accessing it at the same time.
+	 */
 	new = kmalloc(sizeof(*new) + sizeof(new->map[0]) * (old->num + 1),
 		      GFP_KERNEL);
 	if (!new)
@@ -61,8 +65,10 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd)
 	/* Now put new one in place. */
 	rcu_assign_pointer(lg->eventfds, new);
 
-	/* We're not in a big hurry.  Wait until noone's looking at old
-	 * version, then delete it. */
+	/*
+	 * We're not in a big hurry.  Wait until noone's looking at old
+	 * version, then delete it.
+	 */
 	synchronize_rcu();
 	kfree(old);
 
@@ -87,8 +93,10 @@ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input)
 	return err;
 }
 
-/*L:050 Sending an interrupt is done by writing LHREQ_IRQ and an interrupt
- * number to /dev/lguest. */
+/*L:050
+ * Sending an interrupt is done by writing LHREQ_IRQ and an interrupt
+ * number to /dev/lguest.
+ */
 static int user_send_irq(struct lg_cpu *cpu, const unsigned long __user *input)
 {
 	unsigned long irq;
@@ -102,8 +110,10 @@ static int user_send_irq(struct lg_cpu *cpu, const unsigned long __user *input)
 	return 0;
 }
 
-/*L:040 Once our Guest is initialized, the Launcher makes it run by reading
- * from /dev/lguest. */
+/*L:040
+ * Once our Guest is initialized, the Launcher makes it run by reading
+ * from /dev/lguest.
+ */
 static ssize_t read(struct file *file, char __user *user, size_t size,loff_t*o)
 {
 	struct lguest *lg = file->private_data;
@@ -139,8 +149,10 @@ static ssize_t read(struct file *file, char __user *user, size_t size,loff_t*o)
 		return len;
 	}
 
-	/* If we returned from read() last time because the Guest sent I/O,
-	 * clear the flag. */
+	/*
+	 * If we returned from read() last time because the Guest sent I/O,
+	 * clear the flag.
+	 */
 	if (cpu->pending_notify)
 		cpu->pending_notify = 0;
 
@@ -148,8 +160,10 @@ static ssize_t read(struct file *file, char __user *user, size_t size,loff_t*o)
 	return run_guest(cpu, (unsigned long __user *)user);
 }
 
-/*L:025 This actually initializes a CPU.  For the moment, a Guest is only
- * uniprocessor, so "id" is always 0. */
+/*L:025
+ * This actually initializes a CPU.  For the moment, a Guest is only
+ * uniprocessor, so "id" is always 0.
+ */
 static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip)
 {
 	/* We have a limited number the number of CPUs in the lguest struct. */
@@ -164,8 +178,10 @@ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip)
 	/* Each CPU has a timer it can set. */
 	init_clockdev(cpu);
 
-	/* We need a complete page for the Guest registers: they are accessible
-	 * to the Guest and we can only grant it access to whole pages. */
+	/*
+	 * We need a complete page for the Guest registers: they are accessible
+	 * to the Guest and we can only grant it access to whole pages.
+	 */
 	cpu->regs_page = get_zeroed_page(GFP_KERNEL);
 	if (!cpu->regs_page)
 		return -ENOMEM;
@@ -173,29 +189,38 @@ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip)
 	/* We actually put the registers at the bottom of the page. */
 	cpu->regs = (void *)cpu->regs_page + PAGE_SIZE - sizeof(*cpu->regs);
 
-	/* Now we initialize the Guest's registers, handing it the start
-	 * address. */
+	/*
+	 * Now we initialize the Guest's registers, handing it the start
+	 * address.
+	 */
 	lguest_arch_setup_regs(cpu, start_ip);
 
-	/* We keep a pointer to the Launcher task (ie. current task) for when
-	 * other Guests want to wake this one (eg. console input). */
+	/*
+	 * We keep a pointer to the Launcher task (ie. current task) for when
+	 * other Guests want to wake this one (eg. console input).
+	 */
 	cpu->tsk = current;
 
-	/* We need to keep a pointer to the Launcher's memory map, because if
+	/*
+	 * We need to keep a pointer to the Launcher's memory map, because if
 	 * the Launcher dies we need to clean it up.  If we don't keep a
-	 * reference, it is destroyed before close() is called. */
+	 * reference, it is destroyed before close() is called.
+	 */
 	cpu->mm = get_task_mm(cpu->tsk);
 
-	/* We remember which CPU's pages this Guest used last, for optimization
-	 * when the same Guest runs on the same CPU twice. */
+	/*
+	 * We remember which CPU's pages this Guest used last, for optimization
+	 * when the same Guest runs on the same CPU twice.
+	 */
 	cpu->last_pages = NULL;
 
 	/* No error == success. */
 	return 0;
 }
 
-/*L:020 The initialization write supplies 3 pointer sized (32 or 64 bit)
- * values (in addition to the LHREQ_INITIALIZE value).  These are:
+/*L:020
+ * The initialization write supplies 3 pointer sized (32 or 64 bit) values (in
+ * addition to the LHREQ_INITIALIZE value).  These are:
  *
  * base: The start of the Guest-physical memory inside the Launcher memory.
  *
@@ -207,14 +232,15 @@ static int lg_cpu_start(struct lg_cpu *cpu, unsigned id, unsigned long start_ip)
  */
 static int initialize(struct file *file, const unsigned long __user *input)
 {
-	/* "struct lguest" contains everything we (the Host) know about a
-	 * Guest. */
+	/* "struct lguest" contains all we (the Host) know about a Guest. */
 	struct lguest *lg;
 	int err;
 	unsigned long args[3];
 
-	/* We grab the Big Lguest lock, which protects against multiple
-	 * simultaneous initializations. */
+	/*
+	 * We grab the Big Lguest lock, which protects against multiple
+	 * simultaneous initializations.
+	 */
 	mutex_lock(&lguest_lock);
 	/* You can't initialize twice!  Close the device and start again... */
 	if (file->private_data) {
@@ -249,8 +275,10 @@ static int initialize(struct file *file, const unsigned long __user *input)
 	if (err)
 		goto free_eventfds;
 
-	/* Initialize the Guest's shadow page tables, using the toplevel
-	 * address the Launcher gave us.  This allocates memory, so can fail. */
+	/*
+	 * Initialize the Guest's shadow page tables, using the toplevel
+	 * address the Launcher gave us.  This allocates memory, so can fail.
+	 */
 	err = init_guest_pagetable(lg);
 	if (err)
 		goto free_regs;
@@ -275,7 +303,8 @@ unlock:
 	return err;
 }
 
-/*L:010 The first operation the Launcher does must be a write.  All writes
+/*L:010
+ * The first operation the Launcher does must be a write.  All writes
  * start with an unsigned long number: for the first write this must be
  * LHREQ_INITIALIZE to set up the Guest.  After that the Launcher can use
  * writes of other values to send interrupts.
@@ -283,12 +312,15 @@ unlock:
  * Note that we overload the "offset" in the /dev/lguest file to indicate what
  * CPU number we're dealing with.  Currently this is always 0, since we only
  * support uniprocessor Guests, but you can see the beginnings of SMP support
- * here. */
+ * here.
+ */
 static ssize_t write(struct file *file, const char __user *in,
 		     size_t size, loff_t *off)
 {
-	/* Once the Guest is initialized, we hold the "struct lguest" in the
-	 * file private data. */
+	/*
+	 * Once the Guest is initialized, we hold the "struct lguest" in the
+	 * file private data.
+	 */
 	struct lguest *lg = file->private_data;
 	const unsigned long __user *input = (const unsigned long __user *)in;
 	unsigned long req;
@@ -323,13 +355,15 @@ static ssize_t write(struct file *file, const char __user *in,
 	}
 }
 
-/*L:060 The final piece of interface code is the close() routine.  It reverses
+/*L:060
+ * The final piece of interface code is the close() routine.  It reverses
  * everything done in initialize().  This is usually called because the
  * Launcher exited.
  *
  * Note that the close routine returns 0 or a negative error number: it can't
  * really fail, but it can whine.  I blame Sun for this wart, and K&R C for
- * letting them do it. :*/
+ * letting them do it.
+:*/
 static int close(struct inode *inode, struct file *file)
 {
 	struct lguest *lg = file->private_data;
@@ -339,8 +373,10 @@ static int close(struct inode *inode, struct file *file)
 	if (!lg)
 		return 0;
 
-	/* We need the big lock, to protect from inter-guest I/O and other
-	 * Launchers initializing guests. */
+	/*
+	 * We need the big lock, to protect from inter-guest I/O and other
+	 * Launchers initializing guests.
+	 */
 	mutex_lock(&lguest_lock);
 
 	/* Free up the shadow page tables for the Guest. */
@@ -351,8 +387,10 @@ static int close(struct inode *inode, struct file *file)
 		hrtimer_cancel(&lg->cpus[i].hrt);
 		/* We can free up the register page we allocated. */
 		free_page(lg->cpus[i].regs_page);
-		/* Now all the memory cleanups are done, it's safe to release
-		 * the Launcher's memory management structure. */
+		/*
+		 * Now all the memory cleanups are done, it's safe to release
+		 * the Launcher's memory management structure.
+		 */
 		mmput(lg->cpus[i].mm);
 	}
 
@@ -361,8 +399,10 @@ static int close(struct inode *inode, struct file *file)
 		eventfd_ctx_put(lg->eventfds->map[i].event);
 	kfree(lg->eventfds);
 
-	/* If lg->dead doesn't contain an error code it will be NULL or a
-	 * kmalloc()ed string, either of which is ok to hand to kfree(). */
+	/*
+	 * If lg->dead doesn't contain an error code it will be NULL or a
+	 * kmalloc()ed string, either of which is ok to hand to kfree().
+	 */
 	if (!IS_ERR(lg->dead))
 		kfree(lg->dead);
 	/* Free the memory allocated to the lguest_struct */
@@ -386,7 +426,8 @@ static int close(struct inode *inode, struct file *file)
  *
  * We begin our understanding with the Host kernel interface which the Launcher
  * uses: reading and writing a character device called /dev/lguest.  All the
- * work happens in the read(), write() and close() routines: */
+ * work happens in the read(), write() and close() routines:
+ */
 static struct file_operations lguest_fops = {
 	.owner	 = THIS_MODULE,
 	.release = close,
@@ -394,8 +435,10 @@ static struct file_operations lguest_fops = {
 	.read	 = read,
 };
 
-/* This is a textbook example of a "misc" character device.  Populate a "struct
- * miscdevice" and register it with misc_register(). */
+/*
+ * This is a textbook example of a "misc" character device.  Populate a "struct
+ * miscdevice" and register it with misc_register().
+ */
 static struct miscdevice lguest_dev = {
 	.minor	= MISC_DYNAMIC_MINOR,
 	.name	= "lguest",
diff --git a/drivers/lguest/page_tables.c b/drivers/lguest/page_tables.c
index a6fe1abda24..3da902e4b4c 100644
--- a/drivers/lguest/page_tables.c
+++ b/drivers/lguest/page_tables.c
@@ -1,9 +1,11 @@
-/*P:700 The pagetable code, on the other hand, still shows the scars of
+/*P:700
+ * The pagetable code, on the other hand, still shows the scars of
  * previous encounters.  It's functional, and as neat as it can be in the
  * circumstances, but be wary, for these things are subtle and break easily.
  * The Guest provides a virtual to physical mapping, but we can neither trust
  * it nor use it: we verify and convert it here then point the CPU to the
- * converted Guest pages when running the Guest. :*/
+ * converted Guest pages when running the Guest.
+:*/
 
 /* Copyright (C) Rusty Russell IBM Corporation 2006.
  * GPL v2 and any later version */
@@ -17,10 +19,12 @@
 #include <asm/bootparam.h>
 #include "lg.h"
 
-/*M:008 We hold reference to pages, which prevents them from being swapped.
+/*M:008
+ * We hold reference to pages, which prevents them from being swapped.
  * It'd be nice to have a callback in the "struct mm_struct" when Linux wants
  * to swap out.  If we had this, and a shrinker callback to trim PTE pages, we
- * could probably consider launching Guests as non-root. :*/
+ * could probably consider launching Guests as non-root.
+:*/
 
 /*H:300
  * The Page Table Code
@@ -45,16 +49,19 @@
  *  (v) Flushing (throwing away) page tables,
  *  (vi) Mapping the Switcher when the Guest is about to run,
  *  (vii) Setting up the page tables initially.
- :*/
+:*/
 
-
-/* 1024 entries in a page table page maps 1024 pages: 4MB.  The Switcher is
+/*
+ * 1024 entries in a page table page maps 1024 pages: 4MB.  The Switcher is
  * conveniently placed at the top 4MB, so it uses a separate, complete PTE
- * page.  */
+ * page.
+ */
 #define SWITCHER_PGD_INDEX (PTRS_PER_PGD - 1)
 
-/* For PAE we need the PMD index as well. We use the last 2MB, so we
- * will need the last pmd entry of the last pmd page.  */
+/*
+ * For PAE we need the PMD index as well. We use the last 2MB, so we
+ * will need the last pmd entry of the last pmd page.
+ */
 #ifdef CONFIG_X86_PAE
 #define SWITCHER_PMD_INDEX 	(PTRS_PER_PMD - 1)
 #define RESERVE_MEM 		2U
@@ -64,13 +71,16 @@
 #define CHECK_GPGD_MASK		_PAGE_TABLE
 #endif
 
-/* We actually need a separate PTE page for each CPU.  Remember that after the
+/*
+ * We actually need a separate PTE page for each CPU.  Remember that after the
  * Switcher code itself comes two pages for each CPU, and we don't want this
- * CPU's guest to see the pages of any other CPU. */
+ * CPU's guest to see the pages of any other CPU.
+ */
 static DEFINE_PER_CPU(pte_t *, switcher_pte_pages);
 #define switcher_pte_page(cpu) per_cpu(switcher_pte_pages, cpu)
 
-/*H:320 The page table code is curly enough to need helper functions to keep it
+/*H:320
+ * The page table code is curly enough to need helper functions to keep it
  * clear and clean.
  *
  * There are two functions which return pointers to the shadow (aka "real")
@@ -79,7 +89,8 @@ static DEFINE_PER_CPU(pte_t *, switcher_pte_pages);
  * spgd_addr() takes the virtual address and returns a pointer to the top-level
  * page directory entry (PGD) for that address.  Since we keep track of several
  * page tables, the "i" argument tells us which one we're interested in (it's
- * usually the current one). */
+ * usually the current one).
+ */
 static pgd_t *spgd_addr(struct lg_cpu *cpu, u32 i, unsigned long vaddr)
 {
 	unsigned int index = pgd_index(vaddr);
@@ -96,9 +107,11 @@ static pgd_t *spgd_addr(struct lg_cpu *cpu, u32 i, unsigned long vaddr)
 }
 
 #ifdef CONFIG_X86_PAE
-/* This routine then takes the PGD entry given above, which contains the
+/*
+ * This routine then takes the PGD entry given above, which contains the
  * address of the PMD page.  It then returns a pointer to the PMD entry for the
- * given address. */
+ * given address.
+ */
 static pmd_t *spmd_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr)
 {
 	unsigned int index = pmd_index(vaddr);
@@ -119,9 +132,11 @@ static pmd_t *spmd_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr)
 }
 #endif
 
-/* This routine then takes the page directory entry returned above, which
+/*
+ * This routine then takes the page directory entry returned above, which
  * contains the address of the page table entry (PTE) page.  It then returns a
- * pointer to the PTE entry for the given address. */
+ * pointer to the PTE entry for the given address.
+ */
 static pte_t *spte_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr)
 {
 #ifdef CONFIG_X86_PAE
@@ -139,8 +154,10 @@ static pte_t *spte_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr)
 	return &page[pte_index(vaddr)];
 }
 
-/* These two functions just like the above two, except they access the Guest
- * page tables.  Hence they return a Guest address. */
+/*
+ * These two functions just like the above two, except they access the Guest
+ * page tables.  Hence they return a Guest address.
+ */
 static unsigned long gpgd_addr(struct lg_cpu *cpu, unsigned long vaddr)
 {
 	unsigned int index = vaddr >> (PGDIR_SHIFT);
@@ -175,17 +192,21 @@ static unsigned long gpte_addr(struct lg_cpu *cpu,
 #endif
 /*:*/
 
-/*M:014 get_pfn is slow: we could probably try to grab batches of pages here as
- * an optimization (ie. pre-faulting). :*/
+/*M:014
+ * get_pfn is slow: we could probably try to grab batches of pages here as
+ * an optimization (ie. pre-faulting).
+:*/
 
-/*H:350 This routine takes a page number given by the Guest and converts it to
+/*H:350
+ * This routine takes a page number given by the Guest and converts it to
  * an actual, physical page number.  It can fail for several reasons: the
  * virtual address might not be mapped by the Launcher, the write flag is set
  * and the page is read-only, or the write flag was set and the page was
  * shared so had to be copied, but we ran out of memory.
  *
  * This holds a reference to the page, so release_pte() is careful to put that
- * back. */
+ * back.
+ */
 static unsigned long get_pfn(unsigned long virtpfn, int write)
 {
 	struct page *page;
@@ -198,33 +219,41 @@ static unsigned long get_pfn(unsigned long virtpfn, int write)
 	return -1UL;
 }
 
-/*H:340 Converting a Guest page table entry to a shadow (ie. real) page table
+/*H:340
+ * Converting a Guest page table entry to a shadow (ie. real) page table
  * entry can be a little tricky.  The flags are (almost) the same, but the
  * Guest PTE contains a virtual page number: the CPU needs the real page
- * number. */
+ * number.
+ */
 static pte_t gpte_to_spte(struct lg_cpu *cpu, pte_t gpte, int write)
 {
 	unsigned long pfn, base, flags;
 
-	/* The Guest sets the global flag, because it thinks that it is using
+	/*
+	 * The Guest sets the global flag, because it thinks that it is using
 	 * PGE.  We only told it to use PGE so it would tell us whether it was
 	 * flushing a kernel mapping or a userspace mapping.  We don't actually
-	 * use the global bit, so throw it away. */
+	 * use the global bit, so throw it away.
+	 */
 	flags = (pte_flags(gpte) & ~_PAGE_GLOBAL);
 
 	/* The Guest's pages are offset inside the Launcher. */
 	base = (unsigned long)cpu->lg->mem_base / PAGE_SIZE;
 
-	/* We need a temporary "unsigned long" variable to hold the answer from
+	/*
+	 * We need a temporary "unsigned long" variable to hold the answer from
 	 * get_pfn(), because it returns 0xFFFFFFFF on failure, which wouldn't
 	 * fit in spte.pfn.  get_pfn() finds the real physical number of the
-	 * page, given the virtual number. */
+	 * page, given the virtual number.
+	 */
 	pfn = get_pfn(base + pte_pfn(gpte), write);
 	if (pfn == -1UL) {
 		kill_guest(cpu, "failed to get page %lu", pte_pfn(gpte));
-		/* When we destroy the Guest, we'll go through the shadow page
+		/*
+		 * When we destroy the Guest, we'll go through the shadow page
 		 * tables and release_pte() them.  Make sure we don't think
-		 * this one is valid! */
+		 * this one is valid!
+		 */
 		flags = 0;
 	}
 	/* Now we assemble our shadow PTE from the page number and flags. */
@@ -234,8 +263,10 @@ static pte_t gpte_to_spte(struct lg_cpu *cpu, pte_t gpte, int write)
 /*H:460 And to complete the chain, release_pte() looks like this: */
 static void release_pte(pte_t pte)
 {
-	/* Remember that get_user_pages_fast() took a reference to the page, in
-	 * get_pfn()?  We have to put it back now. */
+	/*
+	 * Remember that get_user_pages_fast() took a reference to the page, in
+	 * get_pfn()?  We have to put it back now.
+	 */
 	if (pte_flags(pte) & _PAGE_PRESENT)
 		put_page(pte_page(pte));
 }
@@ -273,7 +304,8 @@ static void check_gpmd(struct lg_cpu *cpu, pmd_t gpmd)
  * and return to the Guest without it knowing.
  *
  * If we fixed up the fault (ie. we mapped the address), this routine returns
- * true.  Otherwise, it was a real fault and we need to tell the Guest. */
+ * true.  Otherwise, it was a real fault and we need to tell the Guest.
+ */
 bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode)
 {
 	pgd_t gpgd;
@@ -298,22 +330,26 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode)
 	if (!(pgd_flags(*spgd) & _PAGE_PRESENT)) {
 		/* No shadow entry: allocate a new shadow PTE page. */
 		unsigned long ptepage = get_zeroed_page(GFP_KERNEL);
-		/* This is not really the Guest's fault, but killing it is
-		 * simple for this corner case. */
+		/*
+		 * This is not really the Guest's fault, but killing it is
+		 * simple for this corner case.
+		 */
 		if (!ptepage) {
 			kill_guest(cpu, "out of memory allocating pte page");
 			return false;
 		}
 		/* We check that the Guest pgd is OK. */
 		check_gpgd(cpu, gpgd);
-		/* And we copy the flags to the shadow PGD entry.  The page
-		 * number in the shadow PGD is the page we just allocated. */
+		/*
+		 * And we copy the flags to the shadow PGD entry.  The page
+		 * number in the shadow PGD is the page we just allocated.
+		 */
 		set_pgd(spgd, __pgd(__pa(ptepage) | pgd_flags(gpgd)));
 	}
 
 #ifdef CONFIG_X86_PAE
 	gpmd = lgread(cpu, gpmd_addr(gpgd, vaddr), pmd_t);
-	/* middle level not present?  We can't map it in. */
+	/* Middle level not present?  We can't map it in. */
 	if (!(pmd_flags(gpmd) & _PAGE_PRESENT))
 		return false;
 
@@ -324,8 +360,10 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode)
 		/* No shadow entry: allocate a new shadow PTE page. */
 		unsigned long ptepage = get_zeroed_page(GFP_KERNEL);
 
-		/* This is not really the Guest's fault, but killing it is
-		* simple for this corner case. */
+		/*
+		 * This is not really the Guest's fault, but killing it is
+		 * simple for this corner case.
+		 */
 		if (!ptepage) {
 			kill_guest(cpu, "out of memory allocating pte page");
 			return false;
@@ -334,17 +372,23 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode)
 		/* We check that the Guest pmd is OK. */
 		check_gpmd(cpu, gpmd);
 
-		/* And we copy the flags to the shadow PMD entry.  The page
-		 * number in the shadow PMD is the page we just allocated. */
+		/*
+		 * And we copy the flags to the shadow PMD entry.  The page
+		 * number in the shadow PMD is the page we just allocated.
+		 */
 		native_set_pmd(spmd, __pmd(__pa(ptepage) | pmd_flags(gpmd)));
 	}
 
-	/* OK, now we look at the lower level in the Guest page table: keep its
-	 * address, because we might update it later. */
+	/*
+	 * OK, now we look at the lower level in the Guest page table: keep its
+	 * address, because we might update it later.
+	 */
 	gpte_ptr = gpte_addr(cpu, gpmd, vaddr);
 #else
-	/* OK, now we look at the lower level in the Guest page table: keep its
-	 * address, because we might update it later. */
+	/*
+	 * OK, now we look at the lower level in the Guest page table: keep its
+	 * address, because we might update it later.
+	 */
 	gpte_ptr = gpte_addr(cpu, gpgd, vaddr);
 #endif
 	gpte = lgread(cpu, gpte_ptr, pte_t);
@@ -353,8 +397,10 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode)
 	if (!(pte_flags(gpte) & _PAGE_PRESENT))
 		return false;
 
-	/* Check they're not trying to write to a page the Guest wants
-	 * read-only (bit 2 of errcode == write). */
+	/*
+	 * Check they're not trying to write to a page the Guest wants
+	 * read-only (bit 2 of errcode == write).
+	 */
 	if ((errcode & 2) && !(pte_flags(gpte) & _PAGE_RW))
 		return false;
 
@@ -362,8 +408,10 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode)
 	if ((errcode & 4) && !(pte_flags(gpte) & _PAGE_USER))
 		return false;
 
-	/* Check that the Guest PTE flags are OK, and the page number is below
-	 * the pfn_limit (ie. not mapping the Launcher binary). */
+	/*
+	 * Check that the Guest PTE flags are OK, and the page number is below
+	 * the pfn_limit (ie. not mapping the Launcher binary).
+	 */
 	check_gpte(cpu, gpte);
 
 	/* Add the _PAGE_ACCESSED and (for a write) _PAGE_DIRTY flag */
@@ -373,29 +421,40 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode)
 
 	/* Get the pointer to the shadow PTE entry we're going to set. */
 	spte = spte_addr(cpu, *spgd, vaddr);
-	/* If there was a valid shadow PTE entry here before, we release it.
-	 * This can happen with a write to a previously read-only entry. */
+
+	/*
+	 * If there was a valid shadow PTE entry here before, we release it.
+	 * This can happen with a write to a previously read-only entry.
+	 */
 	release_pte(*spte);
 
-	/* If this is a write, we insist that the Guest page is writable (the
-	 * final arg to gpte_to_spte()). */
+	/*
+	 * If this is a write, we insist that the Guest page is writable (the
+	 * final arg to gpte_to_spte()).
+	 */
 	if (pte_dirty(gpte))
 		*spte = gpte_to_spte(cpu, gpte, 1);
 	else
-		/* If this is a read, don't set the "writable" bit in the page
+		/*
+		 * If this is a read, don't set the "writable" bit in the page
 		 * table entry, even if the Guest says it's writable.  That way
 		 * we will come back here when a write does actually occur, so
-		 * we can update the Guest's _PAGE_DIRTY flag. */
+		 * we can update the Guest's _PAGE_DIRTY flag.
+		 */
 		native_set_pte(spte, gpte_to_spte(cpu, pte_wrprotect(gpte), 0));
 
-	/* Finally, we write the Guest PTE entry back: we've set the
-	 * _PAGE_ACCESSED and maybe the _PAGE_DIRTY flags. */
+	/*
+	 * Finally, we write the Guest PTE entry back: we've set the
+	 * _PAGE_ACCESSED and maybe the _PAGE_DIRTY flags.
+	 */
 	lgwrite(cpu, gpte_ptr, pte_t, gpte);
 
-	/* The fault is fixed, the page table is populated, the mapping
+	/*
+	 * The fault is fixed, the page table is populated, the mapping
 	 * manipulated, the result returned and the code complete.  A small
 	 * delay and a trace of alliteration are the only indications the Guest
-	 * has that a page fault occurred at all. */
+	 * has that a page fault occurred at all.
+	 */
 	return true;
 }
 
@@ -408,7 +467,8 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode)
  * mapped, so it's overkill.
  *
  * This is a quick version which answers the question: is this virtual address
- * mapped by the shadow page tables, and is it writable? */
+ * mapped by the shadow page tables, and is it writable?
+ */
 static bool page_writable(struct lg_cpu *cpu, unsigned long vaddr)
 {
 	pgd_t *spgd;
@@ -428,16 +488,20 @@ static bool page_writable(struct lg_cpu *cpu, unsigned long vaddr)
 		return false;
 #endif
 
-	/* Check the flags on the pte entry itself: it must be present and
-	 * writable. */
+	/*
+	 * Check the flags on the pte entry itself: it must be present and
+	 * writable.
+	 */
 	flags = pte_flags(*(spte_addr(cpu, *spgd, vaddr)));
 
 	return (flags & (_PAGE_PRESENT|_PAGE_RW)) == (_PAGE_PRESENT|_PAGE_RW);
 }
 
-/* So, when pin_stack_pages() asks us to pin a page, we check if it's already
+/*
+ * So, when pin_stack_pages() asks us to pin a page, we check if it's already
  * in the page tables, and if not, we call demand_page() with error code 2
- * (meaning "write"). */
+ * (meaning "write").
+ */
 void pin_page(struct lg_cpu *cpu, unsigned long vaddr)
 {
 	if (!page_writable(cpu, vaddr) && !demand_page(cpu, vaddr, 2))
@@ -485,9 +549,11 @@ static void release_pgd(pgd_t *spgd)
 	/* If the entry's not present, there's nothing to release. */
 	if (pgd_flags(*spgd) & _PAGE_PRESENT) {
 		unsigned int i;
-		/* Converting the pfn to find the actual PTE page is easy: turn
+		/*
+		 * Converting the pfn to find the actual PTE page is easy: turn
 		 * the page number into a physical address, then convert to a
-		 * virtual address (easy for kernel pages like this one). */
+		 * virtual address (easy for kernel pages like this one).
+		 */
 		pte_t *ptepage = __va(pgd_pfn(*spgd) << PAGE_SHIFT);
 		/* For each entry in the page, we might need to release it. */
 		for (i = 0; i < PTRS_PER_PTE; i++)
@@ -499,9 +565,12 @@ static void release_pgd(pgd_t *spgd)
 	}
 }
 #endif
-/*H:445 We saw flush_user_mappings() twice: once from the flush_user_mappings()
+
+/*H:445
+ * We saw flush_user_mappings() twice: once from the flush_user_mappings()
  * hypercall and once in new_pgdir() when we re-used a top-level pgdir page.
- * It simply releases every PTE page from 0 up to the Guest's kernel address. */
+ * It simply releases every PTE page from 0 up to the Guest's kernel address.
+ */
 static void flush_user_mappings(struct lguest *lg, int idx)
 {
 	unsigned int i;
@@ -510,10 +579,12 @@ static void flush_user_mappings(struct lguest *lg, int idx)
 		release_pgd(lg->pgdirs[idx].pgdir + i);
 }
 
-/*H:440 (v) Flushing (throwing away) page tables,
+/*H:440
+ * (v) Flushing (throwing away) page tables,
  *
  * The Guest has a hypercall to throw away the page tables: it's used when a
- * large number of mappings have been changed. */
+ * large number of mappings have been changed.
+ */
 void guest_pagetable_flush_user(struct lg_cpu *cpu)
 {
 	/* Drop the userspace part of the current page table. */
@@ -551,9 +622,11 @@ unsigned long guest_pa(struct lg_cpu *cpu, unsigned long vaddr)
 	return pte_pfn(gpte) * PAGE_SIZE | (vaddr & ~PAGE_MASK);
 }
 
-/* We keep several page tables.  This is a simple routine to find the page
+/*
+ * We keep several page tables.  This is a simple routine to find the page
  * table (if any) corresponding to this top-level address the Guest has given
- * us. */
+ * us.
+ */
 static unsigned int find_pgdir(struct lguest *lg, unsigned long pgtable)
 {
 	unsigned int i;
@@ -563,9 +636,11 @@ static unsigned int find_pgdir(struct lguest *lg, unsigned long pgtable)
 	return i;
 }
 
-/*H:435 And this is us, creating the new page directory.  If we really do
+/*H:435
+ * And this is us, creating the new page directory.  If we really do
  * allocate a new one (and so the kernel parts are not there), we set
- * blank_pgdir. */
+ * blank_pgdir.
+ */
 static unsigned int new_pgdir(struct lg_cpu *cpu,
 			      unsigned long gpgdir,
 			      int *blank_pgdir)
@@ -575,8 +650,10 @@ static unsigned int new_pgdir(struct lg_cpu *cpu,
 	pmd_t *pmd_table;
 #endif
 
-	/* We pick one entry at random to throw out.  Choosing the Least
-	 * Recently Used might be better, but this is easy. */
+	/*
+	 * We pick one entry at random to throw out.  Choosing the Least
+	 * Recently Used might be better, but this is easy.
+	 */
 	next = random32() % ARRAY_SIZE(cpu->lg->pgdirs);
 	/* If it's never been allocated at all before, try now. */
 	if (!cpu->lg->pgdirs[next].pgdir) {
@@ -587,8 +664,10 @@ static unsigned int new_pgdir(struct lg_cpu *cpu,
 			next = cpu->cpu_pgd;
 		else {
 #ifdef CONFIG_X86_PAE
-			/* In PAE mode, allocate a pmd page and populate the
-			 * last pgd entry. */
+			/*
+			 * In PAE mode, allocate a pmd page and populate the
+			 * last pgd entry.
+			 */
 			pmd_table = (pmd_t *)get_zeroed_page(GFP_KERNEL);
 			if (!pmd_table) {
 				free_page((long)cpu->lg->pgdirs[next].pgdir);
@@ -598,8 +677,10 @@ static unsigned int new_pgdir(struct lg_cpu *cpu,
 				set_pgd(cpu->lg->pgdirs[next].pgdir +
 					SWITCHER_PGD_INDEX,
 					__pgd(__pa(pmd_table) | _PAGE_PRESENT));
-				/* This is a blank page, so there are no kernel
-				 * mappings: caller must map the stack! */
+				/*
+				 * This is a blank page, so there are no kernel
+				 * mappings: caller must map the stack!
+				 */
 				*blank_pgdir = 1;
 			}
 #else
@@ -615,19 +696,23 @@ static unsigned int new_pgdir(struct lg_cpu *cpu,
 	return next;
 }
 
-/*H:430 (iv) Switching page tables
+/*H:430
+ * (iv) Switching page tables
  *
  * Now we've seen all the page table setting and manipulation, let's see
  * what happens when the Guest changes page tables (ie. changes the top-level
- * pgdir).  This occurs on almost every context switch. */
+ * pgdir).  This occurs on almost every context switch.
+ */
 void guest_new_pagetable(struct lg_cpu *cpu, unsigned long pgtable)
 {
 	int newpgdir, repin = 0;
 
 	/* Look to see if we have this one already. */
 	newpgdir = find_pgdir(cpu->lg, pgtable);
-	/* If not, we allocate or mug an existing one: if it's a fresh one,
-	 * repin gets set to 1. */
+	/*
+	 * If not, we allocate or mug an existing one: if it's a fresh one,
+	 * repin gets set to 1.
+	 */
 	if (newpgdir == ARRAY_SIZE(cpu->lg->pgdirs))
 		newpgdir = new_pgdir(cpu, pgtable, &repin);
 	/* Change the current pgd index to the new one. */
@@ -637,9 +722,11 @@ void guest_new_pagetable(struct lg_cpu *cpu, unsigned long pgtable)
 		pin_stack_pages(cpu);
 }
 
-/*H:470 Finally, a routine which throws away everything: all PGD entries in all
+/*H:470
+ * Finally, a routine which throws away everything: all PGD entries in all
  * the shadow page tables, including the Guest's kernel mappings.  This is used
- * when we destroy the Guest. */
+ * when we destroy the Guest.
+ */
 static void release_all_pagetables(struct lguest *lg)
 {
 	unsigned int i, j;
@@ -656,8 +743,10 @@ static void release_all_pagetables(struct lguest *lg)
 			spgd = lg->pgdirs[i].pgdir + SWITCHER_PGD_INDEX;
 			pmdpage = __va(pgd_pfn(*spgd) << PAGE_SHIFT);
 
-			/* And release the pmd entries of that pmd page,
-			 * except for the switcher pmd. */
+			/*
+			 * And release the pmd entries of that pmd page,
+			 * except for the switcher pmd.
+			 */
 			for (k = 0; k < SWITCHER_PMD_INDEX; k++)
 				release_pmd(&pmdpage[k]);
 #endif
@@ -667,10 +756,12 @@ static void release_all_pagetables(struct lguest *lg)
 		}
 }
 
-/* We also throw away everything when a Guest tells us it's changed a kernel
+/*
+ * We also throw away everything when a Guest tells us it's changed a kernel
  * mapping.  Since kernel mappings are in every page table, it's easiest to
  * throw them all away.  This traps the Guest in amber for a while as
- * everything faults back in, but it's rare. */
+ * everything faults back in, but it's rare.
+ */
 void guest_pagetable_clear_all(struct lg_cpu *cpu)
 {
 	release_all_pagetables(cpu->lg);
@@ -678,15 +769,19 @@ void guest_pagetable_clear_all(struct lg_cpu *cpu)
 	pin_stack_pages(cpu);
 }
 /*:*/
-/*M:009 Since we throw away all mappings when a kernel mapping changes, our
+
+/*M:009
+ * Since we throw away all mappings when a kernel mapping changes, our
  * performance sucks for guests using highmem.  In fact, a guest with
  * PAGE_OFFSET 0xc0000000 (the default) and more than about 700MB of RAM is
  * usually slower than a Guest with less memory.
  *
  * This, of course, cannot be fixed.  It would take some kind of... well, I
- * don't know, but the term "puissant code-fu" comes to mind. :*/
+ * don't know, but the term "puissant code-fu" comes to mind.
+:*/
 
-/*H:420 This is the routine which actually sets the page table entry for then
+/*H:420
+ * This is the routine which actually sets the page table entry for then
  * "idx"'th shadow page table.
  *
  * Normally, we can just throw out the old entry and replace it with 0: if they
@@ -715,31 +810,36 @@ static void do_set_pte(struct lg_cpu *cpu, int idx,
 		spmd = spmd_addr(cpu, *spgd, vaddr);
 		if (pmd_flags(*spmd) & _PAGE_PRESENT) {
 #endif
-			/* Otherwise, we start by releasing
-			 * the existing entry. */
+			/* Otherwise, start by releasing the existing entry. */
 			pte_t *spte = spte_addr(cpu, *spgd, vaddr);
 			release_pte(*spte);
 
-			/* If they're setting this entry as dirty or accessed,
-			 * we might as well put that entry they've given us
-			 * in now.  This shaves 10% off a
-			 * copy-on-write micro-benchmark. */
+			/*
+			 * If they're setting this entry as dirty or accessed,
+			 * we might as well put that entry they've given us in
+			 * now.  This shaves 10% off a copy-on-write
+			 * micro-benchmark.
+			 */
 			if (pte_flags(gpte) & (_PAGE_DIRTY | _PAGE_ACCESSED)) {
 				check_gpte(cpu, gpte);
 				native_set_pte(spte,
 						gpte_to_spte(cpu, gpte,
 						pte_flags(gpte) & _PAGE_DIRTY));
-			} else
-				/* Otherwise kill it and we can demand_page()
-				 * it in later. */
+			} else {
+				/*
+				 * Otherwise kill it and we can demand_page()
+				 * it in later.
+				 */
 				native_set_pte(spte, __pte(0));
+			}
 #ifdef CONFIG_X86_PAE
 		}
 #endif
 	}
 }
 
-/*H:410 Updating a PTE entry is a little trickier.
+/*H:410
+ * Updating a PTE entry is a little trickier.
  *
  * We keep track of several different page tables (the Guest uses one for each
  * process, so it makes sense to cache at least a few).  Each of these have
@@ -748,12 +848,15 @@ static void do_set_pte(struct lg_cpu *cpu, int idx,
  * all the page tables, not just the current one.  This is rare.
  *
  * The benefit is that when we have to track a new page table, we can keep all
- * the kernel mappings.  This speeds up context switch immensely. */
+ * the kernel mappings.  This speeds up context switch immensely.
+ */
 void guest_set_pte(struct lg_cpu *cpu,
 		   unsigned long gpgdir, unsigned long vaddr, pte_t gpte)
 {
-	/* Kernel mappings must be changed on all top levels.  Slow, but doesn't
-	 * happen often. */
+	/*
+	 * Kernel mappings must be changed on all top levels.  Slow, but doesn't
+	 * happen often.
+	 */
 	if (vaddr >= cpu->lg->kernel_address) {
 		unsigned int i;
 		for (i = 0; i < ARRAY_SIZE(cpu->lg->pgdirs); i++)
@@ -802,12 +905,14 @@ void guest_set_pmd(struct lguest *lg, unsigned long pmdp, u32 idx)
 }
 #endif
 
-/* Once we know how much memory we have we can construct simple identity
- * (which set virtual == physical) and linear mappings
- * which will get the Guest far enough into the boot to create its own.
+/*
+ * Once we know how much memory we have we can construct simple identity (which
+ * set virtual == physical) and linear mappings which will get the Guest far
+ * enough into the boot to create its own.
  *
  * We lay them out of the way, just below the initrd (which is why we need to
- * know its size here). */
+ * know its size here).
+ */
 static unsigned long setup_pagetables(struct lguest *lg,
 				      unsigned long mem,
 				      unsigned long initrd_size)
@@ -825,8 +930,10 @@ static unsigned long setup_pagetables(struct lguest *lg,
 	unsigned int phys_linear;
 #endif
 
-	/* We have mapped_pages frames to map, so we need
-	 * linear_pages page tables to map them. */
+	/*
+	 * We have mapped_pages frames to map, so we need linear_pages page
+	 * tables to map them.
+	 */
 	mapped_pages = mem / PAGE_SIZE;
 	linear_pages = (mapped_pages + PTRS_PER_PTE - 1) / PTRS_PER_PTE;
 
@@ -839,8 +946,10 @@ static unsigned long setup_pagetables(struct lguest *lg,
 #ifdef CONFIG_X86_PAE
 	pmds = (void *)linear - PAGE_SIZE;
 #endif
-	/* Linear mapping is easy: put every page's address into the
-	 * mapping in order. */
+	/*
+	 * Linear mapping is easy: put every page's address into the
+	 * mapping in order.
+	 */
 	for (i = 0; i < mapped_pages; i++) {
 		pte_t pte;
 		pte = pfn_pte(i, __pgprot(_PAGE_PRESENT|_PAGE_RW|_PAGE_USER));
@@ -848,8 +957,10 @@ static unsigned long setup_pagetables(struct lguest *lg,
 			return -EFAULT;
 	}
 
-	/* The top level points to the linear page table pages above.
-	 * We setup the identity and linear mappings here. */
+	/*
+	 * The top level points to the linear page table pages above.
+	 * We setup the identity and linear mappings here.
+	 */
 #ifdef CONFIG_X86_PAE
 	for (i = j = 0; i < mapped_pages && j < PTRS_PER_PMD;
 	     i += PTRS_PER_PTE, j++) {
@@ -880,15 +991,19 @@ static unsigned long setup_pagetables(struct lguest *lg,
 	}
 #endif
 
-	/* We return the top level (guest-physical) address: remember where
-	 * this is. */
+	/*
+	 * We return the top level (guest-physical) address: remember where
+	 * this is.
+	 */
 	return (unsigned long)pgdir - mem_base;
 }
 
-/*H:500 (vii) Setting up the page tables initially.
+/*H:500
+ * (vii) Setting up the page tables initially.
  *
  * When a Guest is first created, the Launcher tells us where the toplevel of
- * its first page table is.  We set some things up here: */
+ * its first page table is.  We set some things up here:
+ */
 int init_guest_pagetable(struct lguest *lg)
 {
 	u64 mem;
@@ -898,14 +1013,18 @@ int init_guest_pagetable(struct lguest *lg)
 	pgd_t *pgd;
 	pmd_t *pmd_table;
 #endif
-	/* Get the Guest memory size and the ramdisk size from the boot header
-	 * located at lg->mem_base (Guest address 0). */
+	/*
+	 * Get the Guest memory size and the ramdisk size from the boot header
+	 * located at lg->mem_base (Guest address 0).
+	 */
 	if (copy_from_user(&mem, &boot->e820_map[0].size, sizeof(mem))
 	    || get_user(initrd_size, &boot->hdr.ramdisk_size))
 		return -EFAULT;
 
-	/* We start on the first shadow page table, and give it a blank PGD
-	 * page. */
+	/*
+	 * We start on the first shadow page table, and give it a blank PGD
+	 * page.
+	 */
 	lg->pgdirs[0].gpgdir = setup_pagetables(lg, mem, initrd_size);
 	if (IS_ERR_VALUE(lg->pgdirs[0].gpgdir))
 		return lg->pgdirs[0].gpgdir;
@@ -931,17 +1050,21 @@ void page_table_guest_data_init(struct lg_cpu *cpu)
 	/* We get the kernel address: above this is all kernel memory. */
 	if (get_user(cpu->lg->kernel_address,
 		&cpu->lg->lguest_data->kernel_address)
-		/* We tell the Guest that it can't use the top 2 or 4 MB
-		 * of virtual addresses used by the Switcher. */
+		/*
+		 * We tell the Guest that it can't use the top 2 or 4 MB
+		 * of virtual addresses used by the Switcher.
+		 */
 		|| put_user(RESERVE_MEM * 1024 * 1024,
 			&cpu->lg->lguest_data->reserve_mem)
 		|| put_user(cpu->lg->pgdirs[0].gpgdir,
 			&cpu->lg->lguest_data->pgdir))
 		kill_guest(cpu, "bad guest page %p", cpu->lg->lguest_data);
 
-	/* In flush_user_mappings() we loop from 0 to
+	/*
+	 * In flush_user_mappings() we loop from 0 to
 	 * "pgd_index(lg->kernel_address)".  This assumes it won't hit the
-	 * Switcher mappings, so check that now. */
+	 * Switcher mappings, so check that now.
+	 */
 #ifdef CONFIG_X86_PAE
 	if (pgd_index(cpu->lg->kernel_address) == SWITCHER_PGD_INDEX &&
 		pmd_index(cpu->lg->kernel_address) == SWITCHER_PMD_INDEX)
@@ -964,12 +1087,14 @@ void free_guest_pagetable(struct lguest *lg)
 		free_page((long)lg->pgdirs[i].pgdir);
 }
 
-/*H:480 (vi) Mapping the Switcher when the Guest is about to run.
+/*H:480
+ * (vi) Mapping the Switcher when the Guest is about to run.
  *
  * The Switcher and the two pages for this CPU need to be visible in the
  * Guest (and not the pages for other CPUs).  We have the appropriate PTE pages
  * for each CPU already set up, we just need to hook them in now we know which
- * Guest is about to run on this CPU. */
+ * Guest is about to run on this CPU.
+ */
 void map_switcher_in_guest(struct lg_cpu *cpu, struct lguest_pages *pages)
 {
 	pte_t *switcher_pte_page = __get_cpu_var(switcher_pte_pages);
@@ -990,20 +1115,24 @@ void map_switcher_in_guest(struct lg_cpu *cpu, struct lguest_pages *pages)
 #else
 	pgd_t switcher_pgd;
 
-	/* Make the last PGD entry for this Guest point to the Switcher's PTE
-	 * page for this CPU (with appropriate flags). */
+	/*
+	 * Make the last PGD entry for this Guest point to the Switcher's PTE
+	 * page for this CPU (with appropriate flags).
+	 */
 	switcher_pgd = __pgd(__pa(switcher_pte_page) | __PAGE_KERNEL_EXEC);
 
 	cpu->lg->pgdirs[cpu->cpu_pgd].pgdir[SWITCHER_PGD_INDEX] = switcher_pgd;
 
 #endif
-	/* We also change the Switcher PTE page.  When we're running the Guest,
+	/*
+	 * We also change the Switcher PTE page.  When we're running the Guest,
 	 * we want the Guest's "regs" page to appear where the first Switcher
 	 * page for this CPU is.  This is an optimization: when the Switcher
 	 * saves the Guest registers, it saves them into the first page of this
 	 * CPU's "struct lguest_pages": if we make sure the Guest's register
 	 * page is already mapped there, we don't have to copy them out
-	 * again. */
+	 * again.
+	 */
 	pfn = __pa(cpu->regs_page) >> PAGE_SHIFT;
 	native_set_pte(&regs_pte, pfn_pte(pfn, PAGE_KERNEL));
 	native_set_pte(&switcher_pte_page[pte_index((unsigned long)pages)],
@@ -1019,10 +1148,12 @@ static void free_switcher_pte_pages(void)
 		free_page((long)switcher_pte_page(i));
 }
 
-/*H:520 Setting up the Switcher PTE page for given CPU is fairly easy, given
+/*H:520
+ * Setting up the Switcher PTE page for given CPU is fairly easy, given
  * the CPU number and the "struct page"s for the Switcher code itself.
  *
- * Currently the Switcher is less than a page long, so "pages" is always 1. */
+ * Currently the Switcher is less than a page long, so "pages" is always 1.
+ */
 static __init void populate_switcher_pte_page(unsigned int cpu,
 					      struct page *switcher_page[],
 					      unsigned int pages)
@@ -1043,13 +1174,16 @@ static __init void populate_switcher_pte_page(unsigned int cpu,
 	native_set_pte(&pte[i], pfn_pte(page_to_pfn(switcher_page[i]),
 			 __pgprot(_PAGE_PRESENT|_PAGE_ACCESSED|_PAGE_RW)));
 
-	/* The second page contains the "struct lguest_ro_state", and is
-	 * read-only. */
+	/*
+	 * The second page contains the "struct lguest_ro_state", and is
+	 * read-only.
+	 */
 	native_set_pte(&pte[i+1], pfn_pte(page_to_pfn(switcher_page[i+1]),
 			   __pgprot(_PAGE_PRESENT|_PAGE_ACCESSED)));
 }
 
-/* We've made it through the page table code.  Perhaps our tired brains are
+/*
+ * We've made it through the page table code.  Perhaps our tired brains are
  * still processing the details, or perhaps we're simply glad it's over.
  *
  * If nothing else, note that all this complexity in juggling shadow page tables
@@ -1058,10 +1192,13 @@ static __init void populate_switcher_pte_page(unsigned int cpu,
  * uses exotic direct Guest pagetable manipulation, and why both Intel and AMD
  * have implemented shadow page table support directly into hardware.
  *
- * There is just one file remaining in the Host. */
+ * There is just one file remaining in the Host.
+ */
 
-/*H:510 At boot or module load time, init_pagetables() allocates and populates
- * the Switcher PTE page for each CPU. */
+/*H:510
+ * At boot or module load time, init_pagetables() allocates and populates
+ * the Switcher PTE page for each CPU.
+ */
 __init int init_pagetables(struct page **switcher_page, unsigned int pages)
 {
 	unsigned int i;
diff --git a/drivers/lguest/segments.c b/drivers/lguest/segments.c
index 482ed5a1875..951c57b0a7e 100644
--- a/drivers/lguest/segments.c
+++ b/drivers/lguest/segments.c
@@ -1,4 +1,5 @@
-/*P:600 The x86 architecture has segments, which involve a table of descriptors
+/*P:600
+ * The x86 architecture has segments, which involve a table of descriptors
  * which can be used to do funky things with virtual address interpretation.
  * We originally used to use segments so the Guest couldn't alter the
  * Guest<->Host Switcher, and then we had to trim Guest segments, and restore
@@ -8,7 +9,8 @@
  *
  * In these modern times, the segment handling code consists of simple sanity
  * checks, and the worst you'll experience reading this code is butterfly-rash
- * from frolicking through its parklike serenity. :*/
+ * from frolicking through its parklike serenity.
+:*/
 #include "lg.h"
 
 /*H:600
@@ -41,10 +43,12 @@
  * begin.
  */
 
-/* There are several entries we don't let the Guest set.  The TSS entry is the
+/*
+ * There are several entries we don't let the Guest set.  The TSS entry is the
  * "Task State Segment" which controls all kinds of delicate things.  The
  * LGUEST_CS and LGUEST_DS entries are reserved for the Switcher, and the
- * the Guest can't be trusted to deal with double faults. */
+ * the Guest can't be trusted to deal with double faults.
+ */
 static bool ignored_gdt(unsigned int num)
 {
 	return (num == GDT_ENTRY_TSS
@@ -53,42 +57,52 @@ static bool ignored_gdt(unsigned int num)
 		|| num == GDT_ENTRY_DOUBLEFAULT_TSS);
 }
 
-/*H:630 Once the Guest gave us new GDT entries, we fix them up a little.  We
+/*H:630
+ * Once the Guest gave us new GDT entries, we fix them up a little.  We
  * don't care if they're invalid: the worst that can happen is a General
  * Protection Fault in the Switcher when it restores a Guest segment register
  * which tries to use that entry.  Then we kill the Guest for causing such a
- * mess: the message will be "unhandled trap 256". */
+ * mess: the message will be "unhandled trap 256".
+ */
 static void fixup_gdt_table(struct lg_cpu *cpu, unsigned start, unsigned end)
 {
 	unsigned int i;
 
 	for (i = start; i < end; i++) {
-		/* We never copy these ones to real GDT, so we don't care what
-		 * they say */
+		/*
+		 * We never copy these ones to real GDT, so we don't care what
+		 * they say
+		 */
 		if (ignored_gdt(i))
 			continue;
 
-		/* Segment descriptors contain a privilege level: the Guest is
+		/*
+		 * Segment descriptors contain a privilege level: the Guest is
 		 * sometimes careless and leaves this as 0, even though it's
-		 * running at privilege level 1.  If so, we fix it here. */
+		 * running at privilege level 1.  If so, we fix it here.
+		 */
 		if ((cpu->arch.gdt[i].b & 0x00006000) == 0)
 			cpu->arch.gdt[i].b |= (GUEST_PL << 13);
 
-		/* Each descriptor has an "accessed" bit.  If we don't set it
+		/*
+		 * Each descriptor has an "accessed" bit.  If we don't set it
 		 * now, the CPU will try to set it when the Guest first loads
 		 * that entry into a segment register.  But the GDT isn't
-		 * writable by the Guest, so bad things can happen. */
+		 * writable by the Guest, so bad things can happen.
+		 */
 		cpu->arch.gdt[i].b |= 0x00000100;
 	}
 }
 
-/*H:610 Like the IDT, we never simply use the GDT the Guest gives us.  We keep
+/*H:610
+ * Like the IDT, we never simply use the GDT the Guest gives us.  We keep
  * a GDT for each CPU, and copy across the Guest's entries each time we want to
  * run the Guest on that CPU.
  *
  * This routine is called at boot or modprobe time for each CPU to set up the
  * constant GDT entries: the ones which are the same no matter what Guest we're
- * running. */
+ * running.
+ */
 void setup_default_gdt_entries(struct lguest_ro_state *state)
 {
 	struct desc_struct *gdt = state->guest_gdt;
@@ -98,30 +112,37 @@ void setup_default_gdt_entries(struct lguest_ro_state *state)
 	gdt[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT;
 	gdt[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT;
 
-	/* The TSS segment refers to the TSS entry for this particular CPU.
+	/*
+	 * The TSS segment refers to the TSS entry for this particular CPU.
 	 * Forgive the magic flags: the 0x8900 means the entry is Present, it's
 	 * privilege level 0 Available 386 TSS system segment, and the 0x67
-	 * means Saturn is eclipsed by Mercury in the twelfth house. */
+	 * means Saturn is eclipsed by Mercury in the twelfth house.
+	 */
 	gdt[GDT_ENTRY_TSS].a = 0x00000067 | (tss << 16);
 	gdt[GDT_ENTRY_TSS].b = 0x00008900 | (tss & 0xFF000000)
 		| ((tss >> 16) & 0x000000FF);
 }
 
-/* This routine sets up the initial Guest GDT for booting.  All entries start
- * as 0 (unusable). */
+/*
+ * This routine sets up the initial Guest GDT for booting.  All entries start
+ * as 0 (unusable).
+ */
 void setup_guest_gdt(struct lg_cpu *cpu)
 {
-	/* Start with full 0-4G segments... */
+	/*
+	 * Start with full 0-4G segments...except the Guest is allowed to use
+	 * them, so set the privilege level appropriately in the flags.
+	 */
 	cpu->arch.gdt[GDT_ENTRY_KERNEL_CS] = FULL_EXEC_SEGMENT;
 	cpu->arch.gdt[GDT_ENTRY_KERNEL_DS] = FULL_SEGMENT;
-	/* ...except the Guest is allowed to use them, so set the privilege
-	 * level appropriately in the flags. */
 	cpu->arch.gdt[GDT_ENTRY_KERNEL_CS].b |= (GUEST_PL << 13);
 	cpu->arch.gdt[GDT_ENTRY_KERNEL_DS].b |= (GUEST_PL << 13);
 }
 
-/*H:650 An optimization of copy_gdt(), for just the three "thead-local storage"
- * entries. */
+/*H:650
+ * An optimization of copy_gdt(), for just the three "thead-local storage"
+ * entries.
+ */
 void copy_gdt_tls(const struct lg_cpu *cpu, struct desc_struct *gdt)
 {
 	unsigned int i;
@@ -130,26 +151,34 @@ void copy_gdt_tls(const struct lg_cpu *cpu, struct desc_struct *gdt)
 		gdt[i] = cpu->arch.gdt[i];
 }
 
-/*H:640 When the Guest is run on a different CPU, or the GDT entries have
- * changed, copy_gdt() is called to copy the Guest's GDT entries across to this
- * CPU's GDT. */
+/*H:640
+ * When the Guest is run on a different CPU, or the GDT entries have changed,
+ * copy_gdt() is called to copy the Guest's GDT entries across to this CPU's
+ * GDT.
+ */
 void copy_gdt(const struct lg_cpu *cpu, struct desc_struct *gdt)
 {
 	unsigned int i;
 
-	/* The default entries from setup_default_gdt_entries() are not
-	 * replaced.  See ignored_gdt() above. */
+	/*
+	 * The default entries from setup_default_gdt_entries() are not
+	 * replaced.  See ignored_gdt() above.
+	 */
 	for (i = 0; i < GDT_ENTRIES; i++)
 		if (!ignored_gdt(i))
 			gdt[i] = cpu->arch.gdt[i];
 }
 
-/*H:620 This is where the Guest asks us to load a new GDT entry
- * (LHCALL_LOAD_GDT_ENTRY).  We tweak the entry and copy it in. */
+/*H:620
+ * This is where the Guest asks us to load a new GDT entry
+ * (LHCALL_LOAD_GDT_ENTRY).  We tweak the entry and copy it in.
+ */
 void load_guest_gdt_entry(struct lg_cpu *cpu, u32 num, u32 lo, u32 hi)
 {
-	/* We assume the Guest has the same number of GDT entries as the
-	 * Host, otherwise we'd have to dynamically allocate the Guest GDT. */
+	/*
+	 * We assume the Guest has the same number of GDT entries as the
+	 * Host, otherwise we'd have to dynamically allocate the Guest GDT.
+	 */
 	if (num >= ARRAY_SIZE(cpu->arch.gdt))
 		kill_guest(cpu, "too many gdt entries %i", num);
 
@@ -157,15 +186,19 @@ void load_guest_gdt_entry(struct lg_cpu *cpu, u32 num, u32 lo, u32 hi)
 	cpu->arch.gdt[num].a = lo;
 	cpu->arch.gdt[num].b = hi;
 	fixup_gdt_table(cpu, num, num+1);
-	/* Mark that the GDT changed so the core knows it has to copy it again,
-	 * even if the Guest is run on the same CPU. */
+	/*
+	 * Mark that the GDT changed so the core knows it has to copy it again,
+	 * even if the Guest is run on the same CPU.
+	 */
 	cpu->changed |= CHANGED_GDT;
 }
 
-/* This is the fast-track version for just changing the three TLS entries.
+/*
+ * This is the fast-track version for just changing the three TLS entries.
  * Remember that this happens on every context switch, so it's worth
  * optimizing.  But wouldn't it be neater to have a single hypercall to cover
- * both cases? */
+ * both cases?
+ */
 void guest_load_tls(struct lg_cpu *cpu, unsigned long gtls)
 {
 	struct desc_struct *tls = &cpu->arch.gdt[GDT_ENTRY_TLS_MIN];
@@ -175,7 +208,6 @@ void guest_load_tls(struct lg_cpu *cpu, unsigned long gtls)
 	/* Note that just the TLS entries have changed. */
 	cpu->changed |= CHANGED_GDT_TLS;
 }
-/*:*/
 
 /*H:660
  * With this, we have finished the Host.
diff --git a/drivers/lguest/x86/core.c b/drivers/lguest/x86/core.c
index eaf722fe309..96f7d88ec7f 100644
--- a/drivers/lguest/x86/core.c
+++ b/drivers/lguest/x86/core.c
@@ -17,13 +17,15 @@
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
-/*P:450 This file contains the x86-specific lguest code.  It used to be all
+/*P:450
+ * This file contains the x86-specific lguest code.  It used to be all
  * mixed in with drivers/lguest/core.c but several foolhardy code slashers
  * wrestled most of the dependencies out to here in preparation for porting
  * lguest to other architectures (see what I mean by foolhardy?).
  *
  * This also contains a couple of non-obvious setup and teardown pieces which
- * were implemented after days of debugging pain. :*/
+ * were implemented after days of debugging pain.
+:*/
 #include <linux/kernel.h>
 #include <linux/start_kernel.h>
 #include <linux/string.h>
@@ -82,25 +84,33 @@ static DEFINE_PER_CPU(struct lg_cpu *, last_cpu);
  */
 static void copy_in_guest_info(struct lg_cpu *cpu, struct lguest_pages *pages)
 {
-	/* Copying all this data can be quite expensive.  We usually run the
+	/*
+	 * Copying all this data can be quite expensive.  We usually run the
 	 * same Guest we ran last time (and that Guest hasn't run anywhere else
 	 * meanwhile).  If that's not the case, we pretend everything in the
-	 * Guest has changed. */
+	 * Guest has changed.
+	 */
 	if (__get_cpu_var(last_cpu) != cpu || cpu->last_pages != pages) {
 		__get_cpu_var(last_cpu) = cpu;
 		cpu->last_pages = pages;
 		cpu->changed = CHANGED_ALL;
 	}
 
-	/* These copies are pretty cheap, so we do them unconditionally: */
-	/* Save the current Host top-level page directory. */
+	/*
+	 * These copies are pretty cheap, so we do them unconditionally: */
+	/* Save the current Host top-level page directory.
+	 */
 	pages->state.host_cr3 = __pa(current->mm->pgd);
-	/* Set up the Guest's page tables to see this CPU's pages (and no
-	 * other CPU's pages). */
+	/*
+	 * Set up the Guest's page tables to see this CPU's pages (and no
+	 * other CPU's pages).
+	 */
 	map_switcher_in_guest(cpu, pages);
-	/* Set up the two "TSS" members which tell the CPU what stack to use
+	/*
+	 * Set up the two "TSS" members which tell the CPU what stack to use
 	 * for traps which do directly into the Guest (ie. traps at privilege
-	 * level 1). */
+	 * level 1).
+	 */
 	pages->state.guest_tss.sp1 = cpu->esp1;
 	pages->state.guest_tss.ss1 = cpu->ss1;
 
@@ -125,40 +135,53 @@ static void run_guest_once(struct lg_cpu *cpu, struct lguest_pages *pages)
 	/* This is a dummy value we need for GCC's sake. */
 	unsigned int clobber;
 
-	/* Copy the guest-specific information into this CPU's "struct
-	 * lguest_pages". */
+	/*
+	 * Copy the guest-specific information into this CPU's "struct
+	 * lguest_pages".
+	 */
 	copy_in_guest_info(cpu, pages);
 
-	/* Set the trap number to 256 (impossible value).  If we fault while
+	/*
+	 * Set the trap number to 256 (impossible value).  If we fault while
 	 * switching to the Guest (bad segment registers or bug), this will
-	 * cause us to abort the Guest. */
+	 * cause us to abort the Guest.
+	 */
 	cpu->regs->trapnum = 256;
 
-	/* Now: we push the "eflags" register on the stack, then do an "lcall".
+	/*
+	 * Now: we push the "eflags" register on the stack, then do an "lcall".
 	 * This is how we change from using the kernel code segment to using
 	 * the dedicated lguest code segment, as well as jumping into the
 	 * Switcher.
 	 *
 	 * The lcall also pushes the old code segment (KERNEL_CS) onto the
 	 * stack, then the address of this call.  This stack layout happens to
-	 * exactly match the stack layout created by an interrupt... */
+	 * exactly match the stack layout created by an interrupt...
+	 */
 	asm volatile("pushf; lcall *lguest_entry"
-		     /* This is how we tell GCC that %eax ("a") and %ebx ("b")
-		      * are changed by this routine.  The "=" means output. */
+		     /*
+		      * This is how we tell GCC that %eax ("a") and %ebx ("b")
+		      * are changed by this routine.  The "=" means output.
+		      */
 		     : "=a"(clobber), "=b"(clobber)
-		     /* %eax contains the pages pointer.  ("0" refers to the
+		     /*
+		      * %eax contains the pages pointer.  ("0" refers to the
 		      * 0-th argument above, ie "a").  %ebx contains the
 		      * physical address of the Guest's top-level page
-		      * directory. */
+		      * directory.
+		      */
 		     : "0"(pages), "1"(__pa(cpu->lg->pgdirs[cpu->cpu_pgd].pgdir))
-		     /* We tell gcc that all these registers could change,
+		     /*
+		      * We tell gcc that all these registers could change,
 		      * which means we don't have to save and restore them in
-		      * the Switcher. */
+		      * the Switcher.
+		      */
 		     : "memory", "%edx", "%ecx", "%edi", "%esi");
 }
 /*:*/
 
-/*M:002 There are hooks in the scheduler which we can register to tell when we
+/*M:002
+ * There are hooks in the scheduler which we can register to tell when we
  * get kicked off the CPU (preempt_notifier_register()).  This would allow us
  * to lazily disable SYSENTER which would regain some performance, and should
  * also simplify copy_in_guest_info().  Note that we'd still need to restore
@@ -166,56 +189,72 @@ static void run_guest_once(struct lg_cpu *cpu, struct lguest_pages *pages)
  *
  * We could also try using this hooks for PGE, but that might be too expensive.
  *
- * The hooks were designed for KVM, but we can also put them to good use. :*/
+ * The hooks were designed for KVM, but we can also put them to good use.
+:*/
 
-/*H:040 This is the i386-specific code to setup and run the Guest.  Interrupts
- * are disabled: we own the CPU. */
+/*H:040
+ * This is the i386-specific code to setup and run the Guest.  Interrupts
+ * are disabled: we own the CPU.
+ */
 void lguest_arch_run_guest(struct lg_cpu *cpu)
 {
-	/* Remember the awfully-named TS bit?  If the Guest has asked to set it
+	/*
+	 * Remember the awfully-named TS bit?  If the Guest has asked to set it
 	 * we set it now, so we can trap and pass that trap to the Guest if it
-	 * uses the FPU. */
+	 * uses the FPU.
+	 */
 	if (cpu->ts)
 		unlazy_fpu(current);
 
-	/* SYSENTER is an optimized way of doing system calls.  We can't allow
+	/*
+	 * SYSENTER is an optimized way of doing system calls.  We can't allow
 	 * it because it always jumps to privilege level 0.  A normal Guest
 	 * won't try it because we don't advertise it in CPUID, but a malicious
 	 * Guest (or malicious Guest userspace program) could, so we tell the
-	 * CPU to disable it before running the Guest. */
+	 * CPU to disable it before running the Guest.
+	 */
 	if (boot_cpu_has(X86_FEATURE_SEP))
 		wrmsr(MSR_IA32_SYSENTER_CS, 0, 0);
 
-	/* Now we actually run the Guest.  It will return when something
+	/*
+	 * Now we actually run the Guest.  It will return when something
 	 * interesting happens, and we can examine its registers to see what it
-	 * was doing. */
+	 * was doing.
+	 */
 	run_guest_once(cpu, lguest_pages(raw_smp_processor_id()));
 
-	/* Note that the "regs" structure contains two extra entries which are
+	/*
+	 * Note that the "regs" structure contains two extra entries which are
 	 * not really registers: a trap number which says what interrupt or
 	 * trap made the switcher code come back, and an error code which some
-	 * traps set.  */
+	 * traps set.
+	 */
 
 	 /* Restore SYSENTER if it's supposed to be on. */
 	 if (boot_cpu_has(X86_FEATURE_SEP))
 		wrmsr(MSR_IA32_SYSENTER_CS, __KERNEL_CS, 0);
 
-	/* If the Guest page faulted, then the cr2 register will tell us the
+	/*
+	 * If the Guest page faulted, then the cr2 register will tell us the
 	 * bad virtual address.  We have to grab this now, because once we
 	 * re-enable interrupts an interrupt could fault and thus overwrite
-	 * cr2, or we could even move off to a different CPU. */
+	 * cr2, or we could even move off to a different CPU.
+	 */
 	if (cpu->regs->trapnum == 14)
 		cpu->arch.last_pagefault = read_cr2();
-	/* Similarly, if we took a trap because the Guest used the FPU,
+	/*
+	 * Similarly, if we took a trap because the Guest used the FPU,
 	 * we have to restore the FPU it expects to see.
 	 * math_state_restore() may sleep and we may even move off to
 	 * a different CPU. So all the critical stuff should be done
-	 * before this.  */
+	 * before this.
+	 */
 	else if (cpu->regs->trapnum == 7)
 		math_state_restore();
 }
 
-/*H:130 Now we've examined the hypercall code; our Guest can make requests.
+/*H:130
+ * Now we've examined the hypercall code; our Guest can make requests.
  * Our Guest is usually so well behaved; it never tries to do things it isn't
  * allowed to, and uses hypercalls instead.  Unfortunately, Linux's paravirtual
  * infrastructure isn't quite complete, because it doesn't contain replacements
@@ -225,26 +264,33 @@ void lguest_arch_run_guest(struct lg_cpu *cpu)
  *
  * When the Guest uses one of these instructions, we get a trap (General
  * Protection Fault) and come here.  We see if it's one of those troublesome
- * instructions and skip over it.  We return true if we did. */
+ * instructions and skip over it.  We return true if we did.
+ */
 static int emulate_insn(struct lg_cpu *cpu)
 {
 	u8 insn;
 	unsigned int insnlen = 0, in = 0, shift = 0;
-	/* The eip contains the *virtual* address of the Guest's instruction:
-	 * guest_pa just subtracts the Guest's page_offset. */
+	/*
+	 * The eip contains the *virtual* address of the Guest's instruction:
+	 * guest_pa just subtracts the Guest's page_offset.
+	 */
 	unsigned long physaddr = guest_pa(cpu, cpu->regs->eip);
 
-	/* This must be the Guest kernel trying to do something, not userspace!
+	/*
+	 * This must be the Guest kernel trying to do something, not userspace!
 	 * The bottom two bits of the CS segment register are the privilege
-	 * level. */
+	 * level.
+	 */
 	if ((cpu->regs->cs & 3) != GUEST_PL)
 		return 0;
 
 	/* Decoding x86 instructions is icky. */
 	insn = lgread(cpu, physaddr, u8);
 
-	/* 0x66 is an "operand prefix".  It means it's using the upper 16 bits
-	   of the eax register. */
+	/*
+	 * 0x66 is an "operand prefix".  It means it's using the upper 16 bits
+	 * of the eax register.
+	 */
 	if (insn == 0x66) {
 		shift = 16;
 		/* The instruction is 1 byte so far, read the next byte. */
@@ -252,8 +298,10 @@ static int emulate_insn(struct lg_cpu *cpu)
 		insn = lgread(cpu, physaddr + insnlen, u8);
 	}
 
-	/* We can ignore the lower bit for the moment and decode the 4 opcodes
-	 * we need to emulate. */
+	/*
+	 * We can ignore the lower bit for the moment and decode the 4 opcodes
+	 * we need to emulate.
+	 */
 	switch (insn & 0xFE) {
 	case 0xE4: /* in     <next byte>,%al */
 		insnlen += 2;
@@ -274,9 +322,11 @@ static int emulate_insn(struct lg_cpu *cpu)
 		return 0;
 	}
 
-	/* If it was an "IN" instruction, they expect the result to be read
+	/*
+	 * If it was an "IN" instruction, they expect the result to be read
 	 * into %eax, so we change %eax.  We always return all-ones, which
-	 * traditionally means "there's nothing there". */
+	 * traditionally means "there's nothing there".
+	 */
 	if (in) {
 		/* Lower bit tells is whether it's a 16 or 32 bit access */
 		if (insn & 0x1)
@@ -290,7 +340,8 @@ static int emulate_insn(struct lg_cpu *cpu)
 	return 1;
 }
 
-/* Our hypercalls mechanism used to be based on direct software interrupts.
+/*
+ * Our hypercalls mechanism used to be based on direct software interrupts.
  * After Anthony's "Refactor hypercall infrastructure" kvm patch, we decided to
  * change over to using kvm hypercalls.
  *
@@ -318,16 +369,20 @@ static int emulate_insn(struct lg_cpu *cpu)
  */
 static void rewrite_hypercall(struct lg_cpu *cpu)
 {
-	/* This are the opcodes we use to patch the Guest.  The opcode for "int
+	/*
+	 * This are the opcodes we use to patch the Guest.  The opcode for "int
 	 * $0x1f" is "0xcd 0x1f" but vmcall instruction is 3 bytes long, so we
-	 * complete the sequence with a NOP (0x90). */
+	 * complete the sequence with a NOP (0x90).
+	 */
 	u8 insn[3] = {0xcd, 0x1f, 0x90};
 
 	__lgwrite(cpu, guest_pa(cpu, cpu->regs->eip), insn, sizeof(insn));
-	/* The above write might have caused a copy of that page to be made
+	/*
+	 * The above write might have caused a copy of that page to be made
 	 * (if it was read-only).  We need to make sure the Guest has
 	 * up-to-date pagetables.  As this doesn't happen often, we can just
-	 * drop them all. */
+	 * drop them all.
+	 */
 	guest_pagetable_clear_all(cpu);
 }
 
@@ -335,9 +390,11 @@ static bool is_hypercall(struct lg_cpu *cpu)
 {
 	u8 insn[3];
 
-	/* This must be the Guest kernel trying to do something.
+	/*
+	 * This must be the Guest kernel trying to do something.
 	 * The bottom two bits of the CS segment register are the privilege
-	 * level. */
+	 * level.
+	 */
 	if ((cpu->regs->cs & 3) != GUEST_PL)
 		return false;
 
@@ -351,86 +408,105 @@ void lguest_arch_handle_trap(struct lg_cpu *cpu)
 {
 	switch (cpu->regs->trapnum) {
 	case 13: /* We've intercepted a General Protection Fault. */
-		/* Check if this was one of those annoying IN or OUT
+		/*
+		 * Check if this was one of those annoying IN or OUT
 		 * instructions which we need to emulate.  If so, we just go
-		 * back into the Guest after we've done it. */
+		 * back into the Guest after we've done it.
+		 */
 		if (cpu->regs->errcode == 0) {
 			if (emulate_insn(cpu))
 				return;
 		}
-		/* If KVM is active, the vmcall instruction triggers a
-		 * General Protection Fault.  Normally it triggers an
-		 * invalid opcode fault (6): */
+		/*
+		 * If KVM is active, the vmcall instruction triggers a General
+		 * Protection Fault.  Normally it triggers an invalid opcode
+		 * fault (6):
+		 */
 	case 6:
-		/* We need to check if ring == GUEST_PL and
-		 * faulting instruction == vmcall. */
+		/*
+		 * We need to check if ring == GUEST_PL and faulting
+		 * instruction == vmcall.
+		 */
 		if (is_hypercall(cpu)) {
 			rewrite_hypercall(cpu);
 			return;
 		}
 		break;
 	case 14: /* We've intercepted a Page Fault. */
-		/* The Guest accessed a virtual address that wasn't mapped.
+		/*
+		 * The Guest accessed a virtual address that wasn't mapped.
 		 * This happens a lot: we don't actually set up most of the page
 		 * tables for the Guest at all when we start: as it runs it asks
 		 * for more and more, and we set them up as required. In this
 		 * case, we don't even tell the Guest that the fault happened.
 		 *
 		 * The errcode tells whether this was a read or a write, and
-		 * whether kernel or userspace code. */
+		 * whether kernel or userspace code.
+		 */
 		if (demand_page(cpu, cpu->arch.last_pagefault,
 				cpu->regs->errcode))
 			return;
 
-		/* OK, it's really not there (or not OK): the Guest needs to
+		/*
+		 * OK, it's really not there (or not OK): the Guest needs to
 		 * know.  We write out the cr2 value so it knows where the
 		 * fault occurred.
 		 *
 		 * Note that if the Guest were really messed up, this could
 		 * happen before it's done the LHCALL_LGUEST_INIT hypercall, so
-		 * lg->lguest_data could be NULL */
+		 * lg->lguest_data could be NULL
+		 */
 		if (cpu->lg->lguest_data &&
 		    put_user(cpu->arch.last_pagefault,
 			     &cpu->lg->lguest_data->cr2))
 			kill_guest(cpu, "Writing cr2");
 		break;
 	case 7: /* We've intercepted a Device Not Available fault. */
-		/* If the Guest doesn't want to know, we already restored the
-		 * Floating Point Unit, so we just continue without telling
-		 * it. */
+		/*
+		 * If the Guest doesn't want to know, we already restored the
+		 * Floating Point Unit, so we just continue without telling it.
+		 */
 		if (!cpu->ts)
 			return;
 		break;
 	case 32 ... 255:
-		/* These values mean a real interrupt occurred, in which case
+		/*
+		 * These values mean a real interrupt occurred, in which case
 		 * the Host handler has already been run. We just do a
 		 * friendly check if another process should now be run, then
-		 * return to run the Guest again */
+		 * return to run the Guest again
+		 */
 		cond_resched();
 		return;
 	case LGUEST_TRAP_ENTRY:
-		/* Our 'struct hcall_args' maps directly over our regs: we set
-		 * up the pointer now to indicate a hypercall is pending. */
+		/*
+		 * Our 'struct hcall_args' maps directly over our regs: we set
+		 * up the pointer now to indicate a hypercall is pending.
+		 */
 		cpu->hcall = (struct hcall_args *)cpu->regs;
 		return;
 	}
 
 	/* We didn't handle the trap, so it needs to go to the Guest. */
 	if (!deliver_trap(cpu, cpu->regs->trapnum))
-		/* If the Guest doesn't have a handler (either it hasn't
+		/*
+		 * If the Guest doesn't have a handler (either it hasn't
 		 * registered any yet, or it's one of the faults we don't let
-		 * it handle), it dies with this cryptic error message. */
+		 * it handle), it dies with this cryptic error message.
+		 */
 		kill_guest(cpu, "unhandled trap %li at %#lx (%#lx)",
 			   cpu->regs->trapnum, cpu->regs->eip,
 			   cpu->regs->trapnum == 14 ? cpu->arch.last_pagefault
 			   : cpu->regs->errcode);
 }
 
-/* Now we can look at each of the routines this calls, in increasing order of
+/*
+ * Now we can look at each of the routines this calls, in increasing order of
  * complexity: do_hypercalls(), emulate_insn(), maybe_do_interrupt(),
  * deliver_trap() and demand_page().  After all those, we'll be ready to
  * examine the Switcher, and our philosophical understanding of the Host/Guest
- * duality will be complete. :*/
+ * duality will be complete.
+:*/
 static void adjust_pge(void *on)
 {
 	if (on)
@@ -439,13 +515,16 @@ static void adjust_pge(void *on)
 		write_cr4(read_cr4() & ~X86_CR4_PGE);
 }
 
-/*H:020 Now the Switcher is mapped and every thing else is ready, we need to do
- * some more i386-specific initialization. */
+/*H:020
+ * Now the Switcher is mapped and every thing else is ready, we need to do
+ * some more i386-specific initialization.
+ */
 void __init lguest_arch_host_init(void)
 {
 	int i;
 
-	/* Most of the i386/switcher.S doesn't care that it's been moved; on
+	/*
+	 * Most of the i386/switcher.S doesn't care that it's been moved; on
 	 * Intel, jumps are relative, and it doesn't access any references to
 	 * external code or data.
 	 *
@@ -453,7 +532,8 @@ void __init lguest_arch_host_init(void)
 	 * addresses are placed in a table (default_idt_entries), so we need to
 	 * update the table with the new addresses.  switcher_offset() is a
 	 * convenience function which returns the distance between the
-	 * compiled-in switcher code and the high-mapped copy we just made. */
+	 * compiled-in switcher code and the high-mapped copy we just made.
+	 */
 	for (i = 0; i < IDT_ENTRIES; i++)
 		default_idt_entries[i] += switcher_offset();
 
@@ -468,63 +548,81 @@ void __init lguest_arch_host_init(void)
 	for_each_possible_cpu(i) {
 		/* lguest_pages() returns this CPU's two pages. */
 		struct lguest_pages *pages = lguest_pages(i);
-		/* This is a convenience pointer to make the code fit one
-		 * statement to a line. */
+		/* This is a convenience pointer to make the code neater. */
 		struct lguest_ro_state *state = &pages->state;
 
-		/* The Global Descriptor Table: the Host has a different one
+		/*
+		 * The Global Descriptor Table: the Host has a different one
 		 * for each CPU.  We keep a descriptor for the GDT which says
 		 * where it is and how big it is (the size is actually the last
-		 * byte, not the size, hence the "-1"). */
+		 * byte, not the size, hence the "-1").
+		 */
 		state->host_gdt_desc.size = GDT_SIZE-1;
 		state->host_gdt_desc.address = (long)get_cpu_gdt_table(i);
 
-		/* All CPUs on the Host use the same Interrupt Descriptor
+		/*
+		 * All CPUs on the Host use the same Interrupt Descriptor
 		 * Table, so we just use store_idt(), which gets this CPU's IDT
-		 * descriptor. */
+		 * descriptor.
+		 */
 		store_idt(&state->host_idt_desc);
 
-		/* The descriptors for the Guest's GDT and IDT can be filled
+		/*
+		 * The descriptors for the Guest's GDT and IDT can be filled
 		 * out now, too.  We copy the GDT & IDT into ->guest_gdt and
-		 * ->guest_idt before actually running the Guest. */
+		 * ->guest_idt before actually running the Guest.
+		 */
 		state->guest_idt_desc.size = sizeof(state->guest_idt)-1;
 		state->guest_idt_desc.address = (long)&state->guest_idt;
 		state->guest_gdt_desc.size = sizeof(state->guest_gdt)-1;
 		state->guest_gdt_desc.address = (long)&state->guest_gdt;
 
-		/* We know where we want the stack to be when the Guest enters
+		/*
+		 * We know where we want the stack to be when the Guest enters
 		 * the Switcher: in pages->regs.  The stack grows upwards, so
-		 * we start it at the end of that structure. */
+		 * we start it at the end of that structure.
+		 */
 		state->guest_tss.sp0 = (long)(&pages->regs + 1);
-		/* And this is the GDT entry to use for the stack: we keep a
-		 * couple of special LGUEST entries. */
+		/*
+		 * And this is the GDT entry to use for the stack: we keep a
+		 * couple of special LGUEST entries.
+		 */
 		state->guest_tss.ss0 = LGUEST_DS;
 
-		/* x86 can have a finegrained bitmap which indicates what I/O
+		/*
+		 * x86 can have a finegrained bitmap which indicates what I/O
 		 * ports the process can use.  We set it to the end of our
-		 * structure, meaning "none". */
+		 * structure, meaning "none".
+		 */
 		state->guest_tss.io_bitmap_base = sizeof(state->guest_tss);
 
-		/* Some GDT entries are the same across all Guests, so we can
-		 * set them up now. */
+		/*
+		 * Some GDT entries are the same across all Guests, so we can
+		 * set them up now.
+		 */
 		setup_default_gdt_entries(state);
 		/* Most IDT entries are the same for all Guests, too.*/
 		setup_default_idt_entries(state, default_idt_entries);
 
-		/* The Host needs to be able to use the LGUEST segments on this
-		 * CPU, too, so put them in the Host GDT. */
+		/*
+		 * The Host needs to be able to use the LGUEST segments on this
+		 * CPU, too, so put them in the Host GDT.
+		 */
 		get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_CS] = FULL_EXEC_SEGMENT;
 		get_cpu_gdt_table(i)[GDT_ENTRY_LGUEST_DS] = FULL_SEGMENT;
 	}
 
-	/* In the Switcher, we want the %cs segment register to use the
+	/*
+	 * In the Switcher, we want the %cs segment register to use the
 	 * LGUEST_CS GDT entry: we've put that in the Host and Guest GDTs, so
 	 * it will be undisturbed when we switch.  To change %cs and jump we
-	 * need this structure to feed to Intel's "lcall" instruction. */
+	 * need this structure to feed to Intel's "lcall" instruction.
+	 */
 	lguest_entry.offset = (long)switch_to_guest + switcher_offset();
 	lguest_entry.segment = LGUEST_CS;
 
-	/* Finally, we need to turn off "Page Global Enable".  PGE is an
+	/*
+	 * Finally, we need to turn off "Page Global Enable".  PGE is an
 	 * optimization where page table entries are specially marked to show
 	 * they never change.  The Host kernel marks all the kernel pages this
 	 * way because it's always present, even when userspace is running.
@@ -534,16 +632,21 @@ void __init lguest_arch_host_init(void)
 	 * you'll get really weird bugs that you'll chase for two days.
 	 *
 	 * I used to turn PGE off every time we switched to the Guest and back
-	 * on when we return, but that slowed the Switcher down noticibly. */
+	 * on when we return, but that slowed the Switcher down noticibly.
+	 */
 
-	/* We don't need the complexity of CPUs coming and going while we're
-	 * doing this. */
+	/*
+	 * We don't need the complexity of CPUs coming and going while we're
+	 * doing this.
+	 */
 	get_online_cpus();
 	if (cpu_has_pge) { /* We have a broader idea of "global". */
 		/* Remember that this was originally set (for cleanup). */
 		cpu_had_pge = 1;
-		/* adjust_pge is a helper function which sets or unsets the PGE
-		 * bit on its CPU, depending on the argument (0 == unset). */
+		/*
+		 * adjust_pge is a helper function which sets or unsets the PGE
+		 * bit on its CPU, depending on the argument (0 == unset).
+		 */
 		on_each_cpu(adjust_pge, (void *)0, 1);
 		/* Turn off the feature in the global feature set. */
 		clear_cpu_cap(&boot_cpu_data, X86_FEATURE_PGE);
@@ -590,26 +693,32 @@ int lguest_arch_init_hypercalls(struct lg_cpu *cpu)
 {
 	u32 tsc_speed;
 
-	/* The pointer to the Guest's "struct lguest_data" is the only argument.
-	 * We check that address now. */
+	/*
+	 * The pointer to the Guest's "struct lguest_data" is the only argument.
+	 * We check that address now.
+	 */
 	if (!lguest_address_ok(cpu->lg, cpu->hcall->arg1,
 			       sizeof(*cpu->lg->lguest_data)))
 		return -EFAULT;
 
-	/* Having checked it, we simply set lg->lguest_data to point straight
+	/*
+	 * Having checked it, we simply set lg->lguest_data to point straight
 	 * into the Launcher's memory at the right place and then use
 	 * copy_to_user/from_user from now on, instead of lgread/write.  I put
 	 * this in to show that I'm not immune to writing stupid
-	 * optimizations. */
+	 * optimizations.
+	 */
 	cpu->lg->lguest_data = cpu->lg->mem_base + cpu->hcall->arg1;
 
-	/* We insist that the Time Stamp Counter exist and doesn't change with
+	/*
+	 * We insist that the Time Stamp Counter exist and doesn't change with
 	 * cpu frequency.  Some devious chip manufacturers decided that TSC
 	 * changes could be handled in software.  I decided that time going
 	 * backwards might be good for benchmarks, but it's bad for users.
 	 *
 	 * We also insist that the TSC be stable: the kernel detects unreliable
-	 * TSCs for its own purposes, and we use that here. */
+	 * TSCs for its own purposes, and we use that here.
+	 */
 	if (boot_cpu_has(X86_FEATURE_CONSTANT_TSC) && !check_tsc_unstable())
 		tsc_speed = tsc_khz;
 	else
@@ -625,38 +734,47 @@ int lguest_arch_init_hypercalls(struct lg_cpu *cpu)
 }
 /*:*/
 
-/*L:030 lguest_arch_setup_regs()
+/*L:030
+ * lguest_arch_setup_regs()
  *
  * Most of the Guest's registers are left alone: we used get_zeroed_page() to
- * allocate the structure, so they will be 0. */
+ * allocate the structure, so they will be 0.
+ */
 void lguest_arch_setup_regs(struct lg_cpu *cpu, unsigned long start)
 {
 	struct lguest_regs *regs = cpu->regs;
 
-	/* There are four "segment" registers which the Guest needs to boot:
+	/*
+	 * There are four "segment" registers which the Guest needs to boot:
 	 * The "code segment" register (cs) refers to the kernel code segment
 	 * __KERNEL_CS, and the "data", "extra" and "stack" segment registers
 	 * refer to the kernel data segment __KERNEL_DS.
 	 *
 	 * The privilege level is packed into the lower bits.  The Guest runs
-	 * at privilege level 1 (GUEST_PL).*/
+	 * at privilege level 1 (GUEST_PL).
+	 */
 	regs->ds = regs->es = regs->ss = __KERNEL_DS|GUEST_PL;
 	regs->cs = __KERNEL_CS|GUEST_PL;
 
-	/* The "eflags" register contains miscellaneous flags.  Bit 1 (0x002)
+	/*
+	 * The "eflags" register contains miscellaneous flags.  Bit 1 (0x002)
 	 * is supposed to always be "1".  Bit 9 (0x200) controls whether
 	 * interrupts are enabled.  We always leave interrupts enabled while
-	 * running the Guest. */
+	 * running the Guest.
+	 */
 	regs->eflags = X86_EFLAGS_IF | 0x2;
 
-	/* The "Extended Instruction Pointer" register says where the Guest is
-	 * running. */
+	/*
+	 * The "Extended Instruction Pointer" register says where the Guest is
+	 * running.
+	 */
 	regs->eip = start;
 
-	/* %esi points to our boot information, at physical address 0, so don't
-	 * touch it. */
+	/*
+	 * %esi points to our boot information, at physical address 0, so don't
+	 * touch it.
+	 */
 
-	/* There are a couple of GDT entries the Guest expects when first
-	 * booting. */
+	/* There are a couple of GDT entries the Guest expects at boot. */
 	setup_guest_gdt(cpu);
 }
diff --git a/drivers/lguest/x86/switcher_32.S b/drivers/lguest/x86/switcher_32.S
index 3fc15318a80..6dec0979383 100644
--- a/drivers/lguest/x86/switcher_32.S
+++ b/drivers/lguest/x86/switcher_32.S
@@ -1,12 +1,15 @@
-/*P:900 This is the Switcher: code which sits at 0xFFC00000 astride both the
+/*P:900
+ * This is the Switcher: code which sits at 0xFFC00000 astride both the
  * Host and Guest to do the low-level Guest<->Host switch.  It is as simple as
  * it can be made, but it's naturally very specific to x86.
  *
  * You have now completed Preparation.  If this has whet your appetite; if you
  * are feeling invigorated and refreshed then the next, more challenging stage
- * can be found in "make Guest". :*/
+ * can be found in "make Guest".
+ :*/
 
-/*M:012 Lguest is meant to be simple: my rule of thumb is that 1% more LOC must
+/*M:012
+ * Lguest is meant to be simple: my rule of thumb is that 1% more LOC must
  * gain at least 1% more performance.  Since neither LOC nor performance can be
  * measured beforehand, it generally means implementing a feature then deciding
  * if it's worth it.  And once it's implemented, who can say no?
@@ -31,11 +34,14 @@
  * Host (which is actually really easy).
  *
  * Two questions remain.  Would the performance gain outweigh the complexity?
- * And who would write the verse documenting it? :*/
+ * And who would write the verse documenting it?
+:*/
 
-/*M:011 Lguest64 handles NMI.  This gave me NMI envy (until I looked at their
+/*M:011
+ * Lguest64 handles NMI.  This gave me NMI envy (until I looked at their
  * code).  It's worth doing though, since it would let us use oprofile in the
- * Host when a Guest is running. :*/
+ * Host when a Guest is running.
+:*/
 
 /*S:100
  * Welcome to the Switcher itself!
diff --git a/include/linux/lguest.h b/include/linux/lguest.h
index dbf2479e808..0a3a11afd64 100644
--- a/include/linux/lguest.h
+++ b/include/linux/lguest.h
@@ -1,5 +1,7 @@
-/* Things the lguest guest needs to know.  Note: like all lguest interfaces,
- * this is subject to wild and random change between versions. */
+/*
+ * Things the lguest guest needs to know.  Note: like all lguest interfaces,
+ * this is subject to wild and random change between versions.
+ */
 #ifndef _LINUX_LGUEST_H
 #define _LINUX_LGUEST_H
 
@@ -11,32 +13,42 @@
 #define LG_CLOCK_MIN_DELTA	100UL
 #define LG_CLOCK_MAX_DELTA	ULONG_MAX
 
-/*G:031 The second method of communicating with the Host is to via "struct
+/*G:031
+ * The second method of communicating with the Host is to via "struct
  * lguest_data".  Once the Guest's initialization hypercall tells the Host where
- * this is, the Guest and Host both publish information in it. :*/
+ * this is, the Guest and Host both publish information in it.
+:*/
 struct lguest_data
 {
-	/* 512 == enabled (same as eflags in normal hardware).  The Guest
-	 * changes interrupts so often that a hypercall is too slow. */
+	/*
+	 * 512 == enabled (same as eflags in normal hardware).  The Guest
+	 * changes interrupts so often that a hypercall is too slow.
+	 */
 	unsigned int irq_enabled;
 	/* Fine-grained interrupt disabling by the Guest */
 	DECLARE_BITMAP(blocked_interrupts, LGUEST_IRQS);
 
-	/* The Host writes the virtual address of the last page fault here,
+	/*
+	 * The Host writes the virtual address of the last page fault here,
 	 * which saves the Guest a hypercall.  CR2 is the native register where
-	 * this address would normally be found. */
+	 * this address would normally be found.
+	 */
 	unsigned long cr2;
 
 	/* Wallclock time set by the Host. */
 	struct timespec time;
 
-	/* Interrupt pending set by the Host.  The Guest should do a hypercall
-	 * if it re-enables interrupts and sees this set (to X86_EFLAGS_IF). */
+	/*
+	 * Interrupt pending set by the Host.  The Guest should do a hypercall
+	 * if it re-enables interrupts and sees this set (to X86_EFLAGS_IF).
+	 */
 	int irq_pending;
 
-	/* Async hypercall ring.  Instead of directly making hypercalls, we can
+	/*
+	 * Async hypercall ring.  Instead of directly making hypercalls, we can
 	 * place them in here for processing the next time the Host wants.
-	 * This batching can be quite efficient. */
+	 * This batching can be quite efficient.
+	 */
 
 	/* 0xFF == done (set by Host), 0 == pending (set by Guest). */
 	u8 hcall_status[LHCALL_RING_SIZE];
diff --git a/include/linux/lguest_launcher.h b/include/linux/lguest_launcher.h
index bfefbdf7498..495203ff221 100644
--- a/include/linux/lguest_launcher.h
+++ b/include/linux/lguest_launcher.h
@@ -29,8 +29,10 @@ struct lguest_device_desc {
 	__u8 type;
 	/* The number of virtqueues (first in config array) */
 	__u8 num_vq;
-	/* The number of bytes of feature bits.  Multiply by 2: one for host
-	 * features and one for Guest acknowledgements. */
+	/*
+	 * The number of bytes of feature bits.  Multiply by 2: one for host
+	 * features and one for Guest acknowledgements.
+	 */
 	__u8 feature_len;
 	/* The number of bytes of the config array after virtqueues. */
 	__u8 config_len;
@@ -39,8 +41,10 @@ struct lguest_device_desc {
 	__u8 config[0];
 };
 
-/*D:135 This is how we expect the device configuration field for a virtqueue
- * to be laid out in config space. */
+/*D:135
+ * This is how we expect the device configuration field for a virtqueue
+ * to be laid out in config space.
+ */
 struct lguest_vqconfig {
 	/* The number of entries in the virtio_ring */
 	__u16 num;
@@ -61,7 +65,9 @@ enum lguest_req
 	LHREQ_EVENTFD, /* + address, fd. */
 };
 
-/* The alignment to use between consumer and producer parts of vring.
- * x86 pagesize for historical reasons. */
+/*
+ * The alignment to use between consumer and producer parts of vring.
+ * x86 pagesize for historical reasons.
+ */
 #define LGUEST_VRING_ALIGN	4096
 #endif /* _LINUX_LGUEST_LAUNCHER */
-- 
GitLab


From a91d74a3c4de8115295ee87350c13a329164aaaf Mon Sep 17 00:00:00 2001
From: Rusty Russell <rusty@rustcorp.com.au>
Date: Thu, 30 Jul 2009 16:03:45 -0600
Subject: [PATCH 0309/1153] lguest: update commentry

Every so often, after code shuffles, I need to go through and unbitrot
the Lguest Journey (see drivers/lguest/README).  Since we now use RCU in
a simple form in one place I took the opportunity to expand that explanation.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
---
 Documentation/lguest/lguest.c       | 184 +++++++++++++++++++++-------
 arch/x86/include/asm/lguest_hcall.h |   8 +-
 arch/x86/lguest/boot.c              |  99 +++++++++++----
 arch/x86/lguest/i386_head.S         |   2 +
 drivers/lguest/core.c               |   7 +-
 drivers/lguest/hypercalls.c         |   6 +-
 drivers/lguest/lguest_device.c      |  11 +-
 drivers/lguest/lguest_user.c        | 100 +++++++++++++--
 drivers/lguest/page_tables.c        |  84 ++++++++++---
 drivers/lguest/x86/core.c           |   2 +-
 drivers/lguest/x86/switcher_32.S    |   6 +-
 11 files changed, 398 insertions(+), 111 deletions(-)

diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c
index aa66a52b73e..45163651b51 100644
--- a/Documentation/lguest/lguest.c
+++ b/Documentation/lguest/lguest.c
@@ -49,7 +49,7 @@
 #include "linux/virtio_ring.h"
 #include "asm/bootparam.h"
 /*L:110
- * We can ignore the 39 include files we need for this program, but I do want
+ * We can ignore the 42 include files we need for this program, but I do want
  * to draw attention to the use of kernel-style types.
  *
  * As Linus said, "C is a Spartan language, and so should your naming be."  I
@@ -305,6 +305,11 @@ static void *map_zeroed_pages(unsigned int num)
 		    PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE, fd, 0);
 	if (addr == MAP_FAILED)
 		err(1, "Mmaping %u pages of /dev/zero", num);
+
+	/*
+	 * One neat mmap feature is that you can close the fd, and it
+	 * stays mapped.
+	 */
 	close(fd);
 
 	return addr;
@@ -557,7 +562,7 @@ static void tell_kernel(unsigned long start)
 }
 /*:*/
 
-/*
+/*L:200
  * Device Handling.
  *
  * When the Guest gives us a buffer, it sends an array of addresses and sizes.
@@ -608,7 +613,10 @@ static unsigned next_desc(struct vring_desc *desc,
 	return next;
 }
 
-/* This actually sends the interrupt for this virtqueue */
+/*
+ * This actually sends the interrupt for this virtqueue, if we've used a
+ * buffer.
+ */
 static void trigger_irq(struct virtqueue *vq)
 {
 	unsigned long buf[] = { LHREQ_IRQ, vq->config.irq };
@@ -629,12 +637,12 @@ static void trigger_irq(struct virtqueue *vq)
 }
 
 /*
- * This looks in the virtqueue and for the first available buffer, and converts
+ * This looks in the virtqueue for the first available buffer, and converts
  * it to an iovec for convenient access.  Since descriptors consist of some
  * number of output then some number of input descriptors, it's actually two
  * iovecs, but we pack them into one and note how many of each there were.
  *
- * This function returns the descriptor number found.
+ * This function waits if necessary, and returns the descriptor number found.
  */
 static unsigned wait_for_vq_desc(struct virtqueue *vq,
 				 struct iovec iov[],
@@ -644,10 +652,14 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 	struct vring_desc *desc;
 	u16 last_avail = lg_last_avail(vq);
 
+	/* There's nothing available? */
 	while (last_avail == vq->vring.avail->idx) {
 		u64 event;
 
-		/* OK, tell Guest about progress up to now. */
+		/*
+		 * Since we're about to sleep, now is a good time to tell the
+		 * Guest about what we've used up to now.
+		 */
 		trigger_irq(vq);
 
 		/* OK, now we need to know about added descriptors. */
@@ -734,8 +746,9 @@ static unsigned wait_for_vq_desc(struct virtqueue *vq,
 }
 
 /*
- * After we've used one of their buffers, we tell them about it.  We'll then
- * want to send them an interrupt, using trigger_irq().
+ * After we've used one of their buffers, we tell the Guest about it.  Sometime
+ * later we'll want to send them an interrupt using trigger_irq(); note that
+ * wait_for_vq_desc() does that for us if it has to wait.
  */
 static void add_used(struct virtqueue *vq, unsigned int head, int len)
 {
@@ -782,12 +795,12 @@ static void console_input(struct virtqueue *vq)
 	struct console_abort *abort = vq->dev->priv;
 	struct iovec iov[vq->vring.num];
 
-	/* Make sure there's a descriptor waiting. */
+	/* Make sure there's a descriptor available. */
 	head = wait_for_vq_desc(vq, iov, &out_num, &in_num);
 	if (out_num)
 		errx(1, "Output buffers in console in queue?");
 
-	/* Read it in. */
+	/* Read into it.  This is where we usually wait. */
 	len = readv(STDIN_FILENO, iov, in_num);
 	if (len <= 0) {
 		/* Ran out of input? */
@@ -800,6 +813,7 @@ static void console_input(struct virtqueue *vq)
 			pause();
 	}
 
+	/* Tell the Guest we used a buffer. */
 	add_used_and_trigger(vq, head, len);
 
 	/*
@@ -834,15 +848,23 @@ static void console_output(struct virtqueue *vq)
 	unsigned int head, out, in;
 	struct iovec iov[vq->vring.num];
 
+	/* We usually wait in here, for the Guest to give us something. */
 	head = wait_for_vq_desc(vq, iov, &out, &in);
 	if (in)
 		errx(1, "Input buffers in console output queue?");
+
+	/* writev can return a partial write, so we loop here. */
 	while (!iov_empty(iov, out)) {
 		int len = writev(STDOUT_FILENO, iov, out);
 		if (len <= 0)
 			err(1, "Write to stdout gave %i", len);
 		iov_consume(iov, out, len);
 	}
+
+	/*
+	 * We're finished with that buffer: if we're going to sleep,
+	 * wait_for_vq_desc() will prod the Guest with an interrupt.
+	 */
 	add_used(vq, head, 0);
 }
 
@@ -862,15 +884,30 @@ static void net_output(struct virtqueue *vq)
 	unsigned int head, out, in;
 	struct iovec iov[vq->vring.num];
 
+	/* We usually wait in here for the Guest to give us a packet. */
 	head = wait_for_vq_desc(vq, iov, &out, &in);
 	if (in)
 		errx(1, "Input buffers in net output queue?");
+	/*
+	 * Send the whole thing through to /dev/net/tun.  It expects the exact
+	 * same format: what a coincidence!
+	 */
 	if (writev(net_info->tunfd, iov, out) < 0)
 		errx(1, "Write to tun failed?");
+
+	/*
+	 * Done with that one; wait_for_vq_desc() will send the interrupt if
+	 * all packets are processed.
+	 */
 	add_used(vq, head, 0);
 }
 
-/* Will reading from this file descriptor block? */
+/*
+ * Handling network input is a bit trickier, because I've tried to optimize it.
+ *
+ * First we have a helper routine which tells is if from this file descriptor
+ * (ie. the /dev/net/tun device) will block:
+ */
 static bool will_block(int fd)
 {
 	fd_set fdset;
@@ -880,7 +917,11 @@ static bool will_block(int fd)
 	return select(fd+1, &fdset, NULL, NULL, &zero) != 1;
 }
 
-/* This handles packets coming in from the tun device to our Guest. */
+/*
+ * This handles packets coming in from the tun device to our Guest.  Like all
+ * service routines, it gets called again as soon as it returns, so you don't
+ * see a while(1) loop here.
+ */
 static void net_input(struct virtqueue *vq)
 {
 	int len;
@@ -888,21 +929,38 @@ static void net_input(struct virtqueue *vq)
 	struct iovec iov[vq->vring.num];
 	struct net_info *net_info = vq->dev->priv;
 
+	/*
+	 * Get a descriptor to write an incoming packet into.  This will also
+	 * send an interrupt if they're out of descriptors.
+	 */
 	head = wait_for_vq_desc(vq, iov, &out, &in);
 	if (out)
 		errx(1, "Output buffers in net input queue?");
 
-	/* Deliver interrupt now, since we're about to sleep. */
+	/*
+	 * If it looks like we'll block reading from the tun device, send them
+	 * an interrupt.
+	 */
 	if (vq->pending_used && will_block(net_info->tunfd))
 		trigger_irq(vq);
 
+	/*
+	 * Read in the packet.  This is where we normally wait (when there's no
+	 * incoming network traffic).
+	 */
 	len = readv(net_info->tunfd, iov, in);
 	if (len <= 0)
 		err(1, "Failed to read from tun.");
+
+	/*
+	 * Mark that packet buffer as used, but don't interrupt here.  We want
+	 * to wait until we've done as much work as we can.
+	 */
 	add_used(vq, head, len);
 }
+/*:*/
 
-/* This is the helper to create threads. */
+/* This is the helper to create threads: run the service routine in a loop. */
 static int do_thread(void *_vq)
 {
 	struct virtqueue *vq = _vq;
@@ -950,11 +1008,14 @@ static void reset_device(struct device *dev)
 	signal(SIGCHLD, (void *)kill_launcher);
 }
 
+/*L:216
+ * This actually creates the thread which services the virtqueue for a device.
+ */
 static void create_thread(struct virtqueue *vq)
 {
 	/*
-	 * Create stack for thread and run it.  Since the stack grows upwards,
-	 * we point the stack pointer to the end of this region.
+	 * Create stack for thread.  Since the stack grows upwards, we point
+	 * the stack pointer to the end of this region.
 	 */
 	char *stack = malloc(32768);
 	unsigned long args[] = { LHREQ_EVENTFD,
@@ -966,17 +1027,22 @@ static void create_thread(struct virtqueue *vq)
 		err(1, "Creating eventfd");
 	args[2] = vq->eventfd;
 
-	/* Attach an eventfd to this virtqueue: it will go off
-	 * when the Guest does an LHCALL_NOTIFY for this vq. */
+	/*
+	 * Attach an eventfd to this virtqueue: it will go off when the Guest
+	 * does an LHCALL_NOTIFY for this vq.
+	 */
 	if (write(lguest_fd, &args, sizeof(args)) != 0)
 		err(1, "Attaching eventfd");
 
-	/* CLONE_VM: because it has to access the Guest memory, and
-	 * SIGCHLD so we get a signal if it dies. */
+	/*
+	 * CLONE_VM: because it has to access the Guest memory, and SIGCHLD so
+	 * we get a signal if it dies.
+	 */
 	vq->thread = clone(do_thread, stack + 32768, CLONE_VM | SIGCHLD, vq);
 	if (vq->thread == (pid_t)-1)
 		err(1, "Creating clone");
-	/* We close our local copy, now the child has it. */
+
+	/* We close our local copy now the child has it. */
 	close(vq->eventfd);
 }
 
@@ -1028,7 +1094,10 @@ static void update_device_status(struct device *dev)
 	}
 }
 
-/* This is the generic routine we call when the Guest uses LHCALL_NOTIFY. */
+/*L:215
+ * This is the generic routine we call when the Guest uses LHCALL_NOTIFY.  In
+ * particular, it's used to notify us of device status changes during boot.
+ */
 static void handle_output(unsigned long addr)
 {
 	struct device *i;
@@ -1037,18 +1106,32 @@ static void handle_output(unsigned long addr)
 	for (i = devices.dev; i; i = i->next) {
 		struct virtqueue *vq;
 
-		/* Notifications to device descriptors update device status. */
+		/*
+		 * Notifications to device descriptors mean they updated the
+		 * device status.
+		 */
 		if (from_guest_phys(addr) == i->desc) {
 			update_device_status(i);
 			return;
 		}
 
-		/* Devices *can* be used before status is set to DRIVER_OK. */
+		/*
+		 * Devices *can* be used before status is set to DRIVER_OK.
+		 * The original plan was that they would never do this: they
+		 * would always finish setting up their status bits before
+		 * actually touching the virtqueues.  In practice, we allowed
+		 * them to, and they do (eg. the disk probes for partition
+		 * tables as part of initialization).
+		 *
+		 * If we see this, we start the device: once it's running, we
+		 * expect the device to catch all the notifications.
+		 */
 		for (vq = i->vq; vq; vq = vq->next) {
 			if (addr != vq->config.pfn*getpagesize())
 				continue;
 			if (i->running)
 				errx(1, "Notification on running %s", i->name);
+			/* This just calls create_thread() for each virtqueue */
 			start_device(i);
 			return;
 		}
@@ -1132,6 +1215,11 @@ static void add_virtqueue(struct device *dev, unsigned int num_descs,
 	vq->next = NULL;
 	vq->last_avail_idx = 0;
 	vq->dev = dev;
+
+	/*
+	 * This is the routine the service thread will run, and its Process ID
+	 * once it's running.
+	 */
 	vq->service = service;
 	vq->thread = (pid_t)-1;
 
@@ -1202,7 +1290,8 @@ static void set_config(struct device *dev, unsigned len, const void *conf)
 
 /*
  * This routine does all the creation and setup of a new device, including
- * calling new_dev_desc() to allocate the descriptor and device memory.
+ * calling new_dev_desc() to allocate the descriptor and device memory.  We
+ * don't actually start the service threads until later.
  *
  * See what I mean about userspace being boring?
  */
@@ -1478,19 +1567,7 @@ static void setup_tun_net(char *arg)
 		verbose("device %u: tun %s: %s\n",
 			devices.device_num, tapif, arg);
 }
-
-/*
- * Our block (disk) device should be really simple: the Guest asks for a block
- * number and we read or write that position in the file.  Unfortunately, that
- * was amazingly slow: the Guest waits until the read is finished before
- * running anything else, even if it could have been doing useful work.
- *
- * We could use async I/O, except it's reputed to suck so hard that characters
- * actually go missing from your code when you try to use it.
- *
- * So this was one reason why lguest now does all virtqueue servicing in
- * separate threads: it's more efficient and more like a real device.
- */
+/*:*/
 
 /* This hangs off device->priv. */
 struct vblk_info
@@ -1512,8 +1589,16 @@ struct vblk_info
 /*L:210
  * The Disk
  *
- * Remember that the block device is handled by a separate I/O thread.  We head
- * straight into the core of that thread here:
+ * The disk only has one virtqueue, so it only has one thread.  It is really
+ * simple: the Guest asks for a block number and we read or write that position
+ * in the file.
+ *
+ * Before we serviced each virtqueue in a separate thread, that was unacceptably
+ * slow: the Guest waits until the read is finished before running anything
+ * else, even if it could have been doing useful work.
+ *
+ * We could have used async I/O, except it's reputed to suck so hard that
+ * characters actually go missing from your code when you try to use it.
  */
 static void blk_request(struct virtqueue *vq)
 {
@@ -1525,7 +1610,10 @@ static void blk_request(struct virtqueue *vq)
 	struct iovec iov[vq->vring.num];
 	off64_t off;
 
-	/* Get the next request. */
+	/*
+	 * Get the next request, where we normally wait.  It triggers the
+	 * interrupt to acknowledge previously serviced requests (if any).
+	 */
 	head = wait_for_vq_desc(vq, iov, &out_num, &in_num);
 
 	/*
@@ -1539,6 +1627,10 @@ static void blk_request(struct virtqueue *vq)
 
 	out = convert(&iov[0], struct virtio_blk_outhdr);
 	in = convert(&iov[out_num+in_num-1], u8);
+	/*
+	 * For historical reasons, block operations are expressed in 512 byte
+	 * "sectors".
+	 */
 	off = out->sector * 512;
 
 	/*
@@ -1614,6 +1706,7 @@ static void blk_request(struct virtqueue *vq)
 	if (out->type & VIRTIO_BLK_T_BARRIER)
 		fdatasync(vblk->fd);
 
+	/* Finished that request. */
 	add_used(vq, head, wlen);
 }
 
@@ -1682,9 +1775,8 @@ static void rng_input(struct virtqueue *vq)
 		errx(1, "Output buffers in rng?");
 
 	/*
-	 * This is why we convert to iovecs: the readv() call uses them, and so
-	 * it reads straight into the Guest's buffer.  We loop to make sure we
-	 * fill it.
+	 * Just like the console write, we loop to cover the whole iovec.
+	 * In this case, short reads actually happen quite a bit.
 	 */
 	while (!iov_empty(iov, in_num)) {
 		len = readv(rng_info->rfd, iov, in_num);
@@ -1818,7 +1910,9 @@ int main(int argc, char *argv[])
 	devices.lastdev = NULL;
 	devices.next_irq = 1;
 
+	/* We're CPU 0.  In fact, that's the only CPU possible right now. */
 	cpu_id = 0;
+
 	/*
 	 * We need to know how much memory so we can set up the device
 	 * descriptor and memory pages for the devices as we parse the command
@@ -1926,7 +2020,7 @@ int main(int argc, char *argv[])
 	 */
 	tell_kernel(start);
 
-	/* Ensure that we terminate if a child dies. */
+	/* Ensure that we terminate if a device-servicing child dies. */
 	signal(SIGCHLD, kill_launcher);
 
 	/* If we exit via err(), this kills all the threads, restores tty. */
diff --git a/arch/x86/include/asm/lguest_hcall.h b/arch/x86/include/asm/lguest_hcall.h
index cceb73e12e5..ba0eed8aa1a 100644
--- a/arch/x86/include/asm/lguest_hcall.h
+++ b/arch/x86/include/asm/lguest_hcall.h
@@ -35,10 +35,10 @@
  * operations?  There are two ways: the direct way is to make a "hypercall",
  * to make requests of the Host Itself.
  *
- * We use the KVM hypercall mechanism. Seventeen hypercalls are
- * available: the hypercall number is put in the %eax register, and the
- * arguments (when required) are placed in %ebx, %ecx, %edx and %esi.
- * If a return value makes sense, it's returned in %eax.
+ * We use the KVM hypercall mechanism, though completely different hypercall
+ * numbers. Seventeen hypercalls are available: the hypercall number is put in
+ * the %eax register, and the arguments (when required) are placed in %ebx,
+ * %ecx, %edx and %esi.  If a return value makes sense, it's returned in %eax.
  *
  * Grossly invalid calls result in Sudden Death at the hands of the vengeful
  * Host, rather than returning failure.  This reflects Winston Churchill's
diff --git a/arch/x86/lguest/boot.c b/arch/x86/lguest/boot.c
index 025c04d18f2..d677fa9ca65 100644
--- a/arch/x86/lguest/boot.c
+++ b/arch/x86/lguest/boot.c
@@ -154,6 +154,7 @@ static void lazy_hcall1(unsigned long call,
 		async_hcall(call, arg1, 0, 0, 0);
 }
 
+/* You can imagine what lazy_hcall2, 3 and 4 look like. :*/
 static void lazy_hcall2(unsigned long call,
 		       unsigned long arg1,
 		       unsigned long arg2)
@@ -189,8 +190,10 @@ static void lazy_hcall4(unsigned long call,
 }
 #endif
 
-/* When lazy mode is turned off reset the per-cpu lazy mode variable and then
- * issue the do-nothing hypercall to flush any stored calls. */
+/*G:036
+ * When lazy mode is turned off reset the per-cpu lazy mode variable and then
+ * issue the do-nothing hypercall to flush any stored calls.
+:*/
 static void lguest_leave_lazy_mmu_mode(void)
 {
 	kvm_hypercall0(LHCALL_FLUSH_ASYNC);
@@ -250,13 +253,11 @@ extern void lg_irq_enable(void);
 extern void lg_restore_fl(unsigned long flags);
 
 /*M:003
- * Note that we don't check for outstanding interrupts when we re-enable them
- * (or when we unmask an interrupt).  This seems to work for the moment, since
- * interrupts are rare and we'll just get the interrupt on the next timer tick,
- * but now we can run with CONFIG_NO_HZ, we should revisit this.  One way would
- * be to put the "irq_enabled" field in a page by itself, and have the Host
- * write-protect it when an interrupt comes in when irqs are disabled.  There
- * will then be a page fault as soon as interrupts are re-enabled.
+ * We could be more efficient in our checking of outstanding interrupts, rather
+ * than using a branch.  One way would be to put the "irq_enabled" field in a
+ * page by itself, and have the Host write-protect it when an interrupt comes
+ * in when irqs are disabled.  There will then be a page fault as soon as
+ * interrupts are re-enabled.
  *
  * A better method is to implement soft interrupt disable generally for x86:
  * instead of disabling interrupts, we set a flag.  If an interrupt does come
@@ -568,7 +569,7 @@ static void lguest_write_cr4(unsigned long val)
  * cr3 ---> +---------+
  *	    |  	   --------->+---------+
  *	    |	      |	     | PADDR1  |
- *	  Top-level   |	     | PADDR2  |
+ *	  Mid-level   |	     | PADDR2  |
  *	  (PMD) page  |	     | 	       |
  *	    |	      |	   Lower-level |
  *	    |	      |	   (PTE) page  |
@@ -588,23 +589,62 @@ static void lguest_write_cr4(unsigned long val)
  *    Index into top     Index into second      Offset within page
  *  page directory page    pagetable page
  *
- * The kernel spends a lot of time changing both the top-level page directory
- * and lower-level pagetable pages.  The Guest doesn't know physical addresses,
- * so while it maintains these page tables exactly like normal, it also needs
- * to keep the Host informed whenever it makes a change: the Host will create
- * the real page tables based on the Guests'.
+ * Now, unfortunately, this isn't the whole story: Intel added Physical Address
+ * Extension (PAE) to allow 32 bit systems to use 64GB of memory (ie. 36 bits).
+ * These are held in 64-bit page table entries, so we can now only fit 512
+ * entries in a page, and the neat three-level tree breaks down.
+ *
+ * The result is a four level page table:
+ *
+ * cr3 --> [ 4 Upper  ]
+ *	   [   Level  ]
+ *	   [  Entries ]
+ *	   [(PUD Page)]---> +---------+
+ *	 		    |  	   --------->+---------+
+ *	 		    |	      |	     | PADDR1  |
+ *	 		  Mid-level   |	     | PADDR2  |
+ *	 		  (PMD) page  |	     | 	       |
+ *	 		    |	      |	   Lower-level |
+ *	 		    |	      |	   (PTE) page  |
+ *	 		    |	      |	     |	       |
+ *	 		      ....    	     	 ....
+ *
+ *
+ * And the virtual address is decoded as:
+ *
+ *         1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ *      |<-2->|<--- 9 bits ---->|<---- 9 bits --->|<------ 12 bits ------>|
+ * Index into    Index into mid    Index into lower    Offset within page
+ * top entries   directory page     pagetable page
+ *
+ * It's too hard to switch between these two formats at runtime, so Linux only
+ * supports one or the other depending on whether CONFIG_X86_PAE is set.  Many
+ * distributions turn it on, and not just for people with silly amounts of
+ * memory: the larger PTE entries allow room for the NX bit, which lets the
+ * kernel disable execution of pages and increase security.
+ *
+ * This was a problem for lguest, which couldn't run on these distributions;
+ * then Matias Zabaljauregui figured it all out and implemented it, and only a
+ * handful of puppies were crushed in the process!
+ *
+ * Back to our point: the kernel spends a lot of time changing both the
+ * top-level page directory and lower-level pagetable pages.  The Guest doesn't
+ * know physical addresses, so while it maintains these page tables exactly
+ * like normal, it also needs to keep the Host informed whenever it makes a
+ * change: the Host will create the real page tables based on the Guests'.
  */
 
 /*
- * The Guest calls this to set a second-level entry (pte), ie. to map a page
- * into a process' address space.  We set the entry then tell the Host the
- * toplevel and address this corresponds to.  The Guest uses one pagetable per
- * process, so we need to tell the Host which one we're changing (mm->pgd).
+ * The Guest calls this after it has set a second-level entry (pte), ie. to map
+ * a page into a process' address space.  Wetell the Host the toplevel and
+ * address this corresponds to.  The Guest uses one pagetable per process, so
+ * we need to tell the Host which one we're changing (mm->pgd).
  */
 static void lguest_pte_update(struct mm_struct *mm, unsigned long addr,
 			       pte_t *ptep)
 {
 #ifdef CONFIG_X86_PAE
+	/* PAE needs to hand a 64 bit page table entry, so it uses two args. */
 	lazy_hcall4(LHCALL_SET_PTE, __pa(mm->pgd), addr,
 		    ptep->pte_low, ptep->pte_high);
 #else
@@ -612,6 +652,7 @@ static void lguest_pte_update(struct mm_struct *mm, unsigned long addr,
 #endif
 }
 
+/* This is the "set and update" combo-meal-deal version. */
 static void lguest_set_pte_at(struct mm_struct *mm, unsigned long addr,
 			      pte_t *ptep, pte_t pteval)
 {
@@ -672,6 +713,11 @@ static void lguest_set_pte(pte_t *ptep, pte_t pteval)
 }
 
 #ifdef CONFIG_X86_PAE
+/*
+ * With 64-bit PTE values, we need to be careful setting them: if we set 32
+ * bits at a time, the hardware could see a weird half-set entry.  These
+ * versions ensure we update all 64 bits at once.
+ */
 static void lguest_set_pte_atomic(pte_t *ptep, pte_t pte)
 {
 	native_set_pte_atomic(ptep, pte);
@@ -679,13 +725,14 @@ static void lguest_set_pte_atomic(pte_t *ptep, pte_t pte)
 		lazy_hcall1(LHCALL_FLUSH_TLB, 1);
 }
 
-void lguest_pte_clear(struct mm_struct *mm, unsigned long addr, pte_t *ptep)
+static void lguest_pte_clear(struct mm_struct *mm, unsigned long addr,
+			     pte_t *ptep)
 {
 	native_pte_clear(mm, addr, ptep);
 	lguest_pte_update(mm, addr, ptep);
 }
 
-void lguest_pmd_clear(pmd_t *pmdp)
+static void lguest_pmd_clear(pmd_t *pmdp)
 {
 	lguest_set_pmd(pmdp, __pmd(0));
 }
@@ -784,6 +831,14 @@ static void __init lguest_init_IRQ(void)
 	irq_ctx_init(smp_processor_id());
 }
 
+/*
+ * With CONFIG_SPARSE_IRQ, interrupt descriptors are allocated as-needed, so
+ * rather than set them in lguest_init_IRQ we are called here every time an
+ * lguest device needs an interrupt.
+ *
+ * FIXME: irq_to_desc_alloc_node() can fail due to lack of memory, we should
+ * pass that up!
+ */
 void lguest_setup_irq(unsigned int irq)
 {
 	irq_to_desc_alloc_node(irq, 0);
@@ -1298,7 +1353,7 @@ __init void lguest_init(void)
 	 */
 	switch_to_new_gdt(0);
 
-	/* As described in head_32.S, we map the first 128M of memory. */
+	/* We actually boot with all memory mapped, but let's say 128MB. */
 	max_pfn_mapped = (128*1024*1024) >> PAGE_SHIFT;
 
 	/*
diff --git a/arch/x86/lguest/i386_head.S b/arch/x86/lguest/i386_head.S
index db6aa95eb05..27eac0faee4 100644
--- a/arch/x86/lguest/i386_head.S
+++ b/arch/x86/lguest/i386_head.S
@@ -102,6 +102,7 @@ send_interrupts:
 	 * create one manually here.
 	 */
 	.byte 0x0f,0x01,0xc1 /* KVM_HYPERCALL */
+	/* Put eax back the way we found it. */
 	popl %eax
 	ret
 
@@ -125,6 +126,7 @@ ENTRY(lg_restore_fl)
 	jnz send_interrupts
 	/* Again, the normal path has used no extra registers.  Clever, huh? */
 	ret
+/*:*/
 
 /* These demark the EIP range where host should never deliver interrupts. */
 .global lguest_noirq_start
diff --git a/drivers/lguest/core.c b/drivers/lguest/core.c
index cd058bc903f..1e2cb846b3c 100644
--- a/drivers/lguest/core.c
+++ b/drivers/lguest/core.c
@@ -217,10 +217,15 @@ int run_guest(struct lg_cpu *cpu, unsigned long __user *user)
 
 		/*
 		 * It's possible the Guest did a NOTIFY hypercall to the
-		 * Launcher, in which case we return from the read() now.
+		 * Launcher.
 		 */
 		if (cpu->pending_notify) {
+			/*
+			 * Does it just needs to write to a registered
+			 * eventfd (ie. the appropriate virtqueue thread)?
+			 */
 			if (!send_notify_to_eventfd(cpu)) {
+				/* OK, we tell the main Laucher. */
 				if (put_user(cpu->pending_notify, user))
 					return -EFAULT;
 				return sizeof(cpu->pending_notify);
diff --git a/drivers/lguest/hypercalls.c b/drivers/lguest/hypercalls.c
index 787ab4bc09f..83511eb0923 100644
--- a/drivers/lguest/hypercalls.c
+++ b/drivers/lguest/hypercalls.c
@@ -59,7 +59,7 @@ static void do_hcall(struct lg_cpu *cpu, struct hcall_args *args)
 	case LHCALL_SHUTDOWN: {
 		char msg[128];
 		/*
-		 * Shutdown is such a trivial hypercall that we do it in four
+		 * Shutdown is such a trivial hypercall that we do it in five
 		 * lines right here.
 		 *
 		 * If the lgread fails, it will call kill_guest() itself; the
@@ -245,6 +245,10 @@ static void initialize(struct lg_cpu *cpu)
  * device), the Guest will still see the old page.  In practice, this never
  * happens: why would the Guest read a page which it has never written to?  But
  * a similar scenario might one day bite us, so it's worth mentioning.
+ *
+ * Note that if we used a shared anonymous mapping in the Launcher instead of
+ * mapping /dev/zero private, we wouldn't worry about cop-on-write.  And we
+ * need that to switch the Launcher to processes (away from threads) anyway.
 :*/
 
 /*H:100
diff --git a/drivers/lguest/lguest_device.c b/drivers/lguest/lguest_device.c
index cc000e79c3d..1401c1ace1e 100644
--- a/drivers/lguest/lguest_device.c
+++ b/drivers/lguest/lguest_device.c
@@ -236,7 +236,7 @@ static void lg_notify(struct virtqueue *vq)
 extern void lguest_setup_irq(unsigned int irq);
 
 /*
- * This routine finds the first virtqueue described in the configuration of
+ * This routine finds the Nth virtqueue described in the configuration of
  * this device and sets it up.
  *
  * This is kind of an ugly duckling.  It'd be nicer to have a standard
@@ -244,9 +244,6 @@ extern void lguest_setup_irq(unsigned int irq);
  * everyone wants to do it differently.  The KVM coders want the Guest to
  * allocate its own pages and tell the Host where they are, but for lguest it's
  * simpler for the Host to simply tell us where the pages are.
- *
- * So we provide drivers with a "find the Nth virtqueue and set it up"
- * function.
  */
 static struct virtqueue *lg_find_vq(struct virtio_device *vdev,
 				    unsigned index,
@@ -422,7 +419,11 @@ static void add_lguest_device(struct lguest_device_desc *d,
 
 	/* This devices' parent is the lguest/ dir. */
 	ldev->vdev.dev.parent = lguest_root;
-	/* We have a unique device index thanks to the dev_index counter. */
+	/*
+	 * The device type comes straight from the descriptor.  There's also a
+	 * device vendor field in the virtio_device struct, which we leave as
+	 * 0.
+	 */
 	ldev->vdev.id.device = d->type;
 	/*
 	 * We have a simple set of routines for querying the device's
diff --git a/drivers/lguest/lguest_user.c b/drivers/lguest/lguest_user.c
index 7e92017103d..b4d3f7ca554 100644
--- a/drivers/lguest/lguest_user.c
+++ b/drivers/lguest/lguest_user.c
@@ -1,9 +1,8 @@
-/*P:200
- * This contains all the /dev/lguest code, whereby the userspace launcher
+/*P:200 This contains all the /dev/lguest code, whereby the userspace launcher
  * controls and communicates with the Guest.  For example, the first write will
- * tell us the Guest's memory layout, pagetable, entry point and kernel address
- * offset.  A read will run the Guest until something happens, such as a signal
- * or the Guest doing a NOTIFY out to the Launcher.
+ * tell us the Guest's memory layout and entry point.  A read will run the
+ * Guest until something happens, such as a signal or the Guest doing a NOTIFY
+ * out to the Launcher.
 :*/
 #include <linux/uaccess.h>
 #include <linux/miscdevice.h>
@@ -13,14 +12,41 @@
 #include <linux/file.h>
 #include "lg.h"
 
+/*L:056
+ * Before we move on, let's jump ahead and look at what the kernel does when
+ * it needs to look up the eventfds.  That will complete our picture of how we
+ * use RCU.
+ *
+ * The notification value is in cpu->pending_notify: we return true if it went
+ * to an eventfd.
+ */
 bool send_notify_to_eventfd(struct lg_cpu *cpu)
 {
 	unsigned int i;
 	struct lg_eventfd_map *map;
 
-	/* lg->eventfds is RCU-protected */
+	/*
+	 * This "rcu_read_lock()" helps track when someone is still looking at
+	 * the (RCU-using) eventfds array.  It's not actually a lock at all;
+	 * indeed it's a noop in many configurations.  (You didn't expect me to
+	 * explain all the RCU secrets here, did you?)
+	 */
 	rcu_read_lock();
+	/*
+	 * rcu_dereference is the counter-side of rcu_assign_pointer(); it
+	 * makes sure we don't access the memory pointed to by
+	 * cpu->lg->eventfds before cpu->lg->eventfds is set.  Sounds crazy,
+	 * but Alpha allows this!  Paul McKenney points out that a really
+	 * aggressive compiler could have the same effect:
+	 *   http://lists.ozlabs.org/pipermail/lguest/2009-July/001560.html
+	 *
+	 * So play safe, use rcu_dereference to get the rcu-protected pointer:
+	 */
 	map = rcu_dereference(cpu->lg->eventfds);
+	/*
+	 * Simple array search: even if they add an eventfd while we do this,
+	 * we'll continue to use the old array and just won't see the new one.
+	 */
 	for (i = 0; i < map->num; i++) {
 		if (map->map[i].addr == cpu->pending_notify) {
 			eventfd_signal(map->map[i].event, 1);
@@ -28,14 +54,43 @@ bool send_notify_to_eventfd(struct lg_cpu *cpu)
 			break;
 		}
 	}
+	/* We're done with the rcu-protected variable cpu->lg->eventfds. */
 	rcu_read_unlock();
+
+	/* If we cleared the notification, it's because we found a match. */
 	return cpu->pending_notify == 0;
 }
 
+/*L:055
+ * One of the more tricksy tricks in the Linux Kernel is a technique called
+ * Read Copy Update.  Since one point of lguest is to teach lguest journeyers
+ * about kernel coding, I use it here.  (In case you're curious, other purposes
+ * include learning about virtualization and instilling a deep appreciation for
+ * simplicity and puppies).
+ *
+ * We keep a simple array which maps LHCALL_NOTIFY values to eventfds, but we
+ * add new eventfds without ever blocking readers from accessing the array.
+ * The current Launcher only does this during boot, so that never happens.  But
+ * Read Copy Update is cool, and adding a lock risks damaging even more puppies
+ * than this code does.
+ *
+ * We allocate a brand new one-larger array, copy the old one and add our new
+ * element.  Then we make the lg eventfd pointer point to the new array.
+ * That's the easy part: now we need to free the old one, but we need to make
+ * sure no slow CPU somewhere is still looking at it.  That's what
+ * synchronize_rcu does for us: waits until every CPU has indicated that it has
+ * moved on to know it's no longer using the old one.
+ *
+ * If that's unclear, see http://en.wikipedia.org/wiki/Read-copy-update.
+ */
 static int add_eventfd(struct lguest *lg, unsigned long addr, int fd)
 {
 	struct lg_eventfd_map *new, *old = lg->eventfds;
 
+	/*
+	 * We don't allow notifications on value 0 anyway (pending_notify of
+	 * 0 means "nothing pending").
+	 */
 	if (!addr)
 		return -EINVAL;
 
@@ -62,12 +117,20 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd)
 	}
 	new->num++;
 
-	/* Now put new one in place. */
+	/*
+	 * Now put new one in place: rcu_assign_pointer() is a fancy way of
+	 * doing "lg->eventfds = new", but it uses memory barriers to make
+	 * absolutely sure that the contents of "new" written above is nailed
+	 * down before we actually do the assignment.
+	 *
+	 * We have to think about these kinds of things when we're operating on
+	 * live data without locks.
+	 */
 	rcu_assign_pointer(lg->eventfds, new);
 
 	/*
 	 * We're not in a big hurry.  Wait until noone's looking at old
-	 * version, then delete it.
+	 * version, then free it.
 	 */
 	synchronize_rcu();
 	kfree(old);
@@ -75,6 +138,14 @@ static int add_eventfd(struct lguest *lg, unsigned long addr, int fd)
 	return 0;
 }
 
+/*L:052
+ * Receiving notifications from the Guest is usually done by attaching a
+ * particular LHCALL_NOTIFY value to an event filedescriptor.  The eventfd will
+ * become readable when the Guest does an LHCALL_NOTIFY with that value.
+ *
+ * This is really convenient for processing each virtqueue in a separate
+ * thread.
+ */
 static int attach_eventfd(struct lguest *lg, const unsigned long __user *input)
 {
 	unsigned long addr, fd;
@@ -86,6 +157,11 @@ static int attach_eventfd(struct lguest *lg, const unsigned long __user *input)
 	if (get_user(fd, input) != 0)
 		return -EFAULT;
 
+	/*
+	 * Just make sure two callers don't add eventfds at once.  We really
+	 * only need to lock against callers adding to the same Guest, so using
+	 * the Big Lguest Lock is overkill.  But this is setup, not a fast path.
+	 */
 	mutex_lock(&lguest_lock);
 	err = add_eventfd(lg, addr, fd);
 	mutex_unlock(&lguest_lock);
@@ -106,6 +182,10 @@ static int user_send_irq(struct lg_cpu *cpu, const unsigned long __user *input)
 	if (irq >= LGUEST_IRQS)
 		return -EINVAL;
 
+	/*
+	 * Next time the Guest runs, the core code will see if it can deliver
+	 * this interrupt.
+	 */
 	set_interrupt(cpu, irq);
 	return 0;
 }
@@ -307,10 +387,10 @@ unlock:
  * The first operation the Launcher does must be a write.  All writes
  * start with an unsigned long number: for the first write this must be
  * LHREQ_INITIALIZE to set up the Guest.  After that the Launcher can use
- * writes of other values to send interrupts.
+ * writes of other values to send interrupts or set up receipt of notifications.
  *
  * Note that we overload the "offset" in the /dev/lguest file to indicate what
- * CPU number we're dealing with.  Currently this is always 0, since we only
+ * CPU number we're dealing with.  Currently this is always 0 since we only
  * support uniprocessor Guests, but you can see the beginnings of SMP support
  * here.
  */
diff --git a/drivers/lguest/page_tables.c b/drivers/lguest/page_tables.c
index 3da902e4b4c..a8d0aee3bc0 100644
--- a/drivers/lguest/page_tables.c
+++ b/drivers/lguest/page_tables.c
@@ -29,10 +29,10 @@
 /*H:300
  * The Page Table Code
  *
- * We use two-level page tables for the Guest.  If you're not entirely
- * comfortable with virtual addresses, physical addresses and page tables then
- * I recommend you review arch/x86/lguest/boot.c's "Page Table Handling" (with
- * diagrams!).
+ * We use two-level page tables for the Guest, or three-level with PAE.  If
+ * you're not entirely comfortable with virtual addresses, physical addresses
+ * and page tables then I recommend you review arch/x86/lguest/boot.c's "Page
+ * Table Handling" (with diagrams!).
  *
  * The Guest keeps page tables, but we maintain the actual ones here: these are
  * called "shadow" page tables.  Which is a very Guest-centric name: these are
@@ -52,9 +52,8 @@
 :*/
 
 /*
- * 1024 entries in a page table page maps 1024 pages: 4MB.  The Switcher is
- * conveniently placed at the top 4MB, so it uses a separate, complete PTE
- * page.
+ * The Switcher uses the complete top PTE page.  That's 1024 PTE entries (4MB)
+ * or 512 PTE entries with PAE (2MB).
  */
 #define SWITCHER_PGD_INDEX (PTRS_PER_PGD - 1)
 
@@ -81,7 +80,8 @@ static DEFINE_PER_CPU(pte_t *, switcher_pte_pages);
 
 /*H:320
  * The page table code is curly enough to need helper functions to keep it
- * clear and clean.
+ * clear and clean.  The kernel itself provides many of them; one advantage
+ * of insisting that the Guest and Host use the same CONFIG_PAE setting.
  *
  * There are two functions which return pointers to the shadow (aka "real")
  * page tables.
@@ -155,7 +155,7 @@ static pte_t *spte_addr(struct lg_cpu *cpu, pgd_t spgd, unsigned long vaddr)
 }
 
 /*
- * These two functions just like the above two, except they access the Guest
+ * These functions are just like the above two, except they access the Guest
  * page tables.  Hence they return a Guest address.
  */
 static unsigned long gpgd_addr(struct lg_cpu *cpu, unsigned long vaddr)
@@ -165,6 +165,7 @@ static unsigned long gpgd_addr(struct lg_cpu *cpu, unsigned long vaddr)
 }
 
 #ifdef CONFIG_X86_PAE
+/* Follow the PGD to the PMD. */
 static unsigned long gpmd_addr(pgd_t gpgd, unsigned long vaddr)
 {
 	unsigned long gpage = pgd_pfn(gpgd) << PAGE_SHIFT;
@@ -172,6 +173,7 @@ static unsigned long gpmd_addr(pgd_t gpgd, unsigned long vaddr)
 	return gpage + pmd_index(vaddr) * sizeof(pmd_t);
 }
 
+/* Follow the PMD to the PTE. */
 static unsigned long gpte_addr(struct lg_cpu *cpu,
 			       pmd_t gpmd, unsigned long vaddr)
 {
@@ -181,6 +183,7 @@ static unsigned long gpte_addr(struct lg_cpu *cpu,
 	return gpage + pte_index(vaddr) * sizeof(pte_t);
 }
 #else
+/* Follow the PGD to the PTE (no mid-level for !PAE). */
 static unsigned long gpte_addr(struct lg_cpu *cpu,
 				pgd_t gpgd, unsigned long vaddr)
 {
@@ -314,6 +317,7 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode)
 	pte_t gpte;
 	pte_t *spte;
 
+	/* Mid level for PAE. */
 #ifdef CONFIG_X86_PAE
 	pmd_t *spmd;
 	pmd_t gpmd;
@@ -391,6 +395,8 @@ bool demand_page(struct lg_cpu *cpu, unsigned long vaddr, int errcode)
 	 */
 	gpte_ptr = gpte_addr(cpu, gpgd, vaddr);
 #endif
+
+	/* Read the actual PTE value. */
 	gpte = lgread(cpu, gpte_ptr, pte_t);
 
 	/* If this page isn't in the Guest page tables, we can't page it in. */
@@ -507,6 +513,7 @@ void pin_page(struct lg_cpu *cpu, unsigned long vaddr)
 	if (!page_writable(cpu, vaddr) && !demand_page(cpu, vaddr, 2))
 		kill_guest(cpu, "bad stack page %#lx", vaddr);
 }
+/*:*/
 
 #ifdef CONFIG_X86_PAE
 static void release_pmd(pmd_t *spmd)
@@ -543,7 +550,11 @@ static void release_pgd(pgd_t *spgd)
 }
 
 #else /* !CONFIG_X86_PAE */
-/*H:450 If we chase down the release_pgd() code, it looks like this: */
+/*H:450
+ * If we chase down the release_pgd() code, the non-PAE version looks like
+ * this.  The PAE version is almost identical, but instead of calling
+ * release_pte it calls release_pmd(), which looks much like this.
+ */
 static void release_pgd(pgd_t *spgd)
 {
 	/* If the entry's not present, there's nothing to release. */
@@ -898,17 +909,21 @@ void guest_set_pgd(struct lguest *lg, unsigned long gpgdir, u32 idx)
 		/* ... throw it away. */
 		release_pgd(lg->pgdirs[pgdir].pgdir + idx);
 }
+
 #ifdef CONFIG_X86_PAE
+/* For setting a mid-level, we just throw everything away.  It's easy. */
 void guest_set_pmd(struct lguest *lg, unsigned long pmdp, u32 idx)
 {
 	guest_pagetable_clear_all(&lg->cpus[0]);
 }
 #endif
 
-/*
- * Once we know how much memory we have we can construct simple identity (which
+/*H:505
+ * To get through boot, we construct simple identity page mappings (which
  * set virtual == physical) and linear mappings which will get the Guest far
- * enough into the boot to create its own.
+ * enough into the boot to create its own.  The linear mapping means we
+ * simplify the Guest boot, but it makes assumptions about their PAGE_OFFSET,
+ * as you'll see.
  *
  * We lay them out of the way, just below the initrd (which is why we need to
  * know its size here).
@@ -944,6 +959,10 @@ static unsigned long setup_pagetables(struct lguest *lg,
 	linear = (void *)pgdir - linear_pages * PAGE_SIZE;
 
 #ifdef CONFIG_X86_PAE
+	/*
+	 * And the single mid page goes below that.  We only use one, but
+	 * that's enough to map 1G, which definitely gets us through boot.
+	 */
 	pmds = (void *)linear - PAGE_SIZE;
 #endif
 	/*
@@ -957,13 +976,14 @@ static unsigned long setup_pagetables(struct lguest *lg,
 			return -EFAULT;
 	}
 
+#ifdef CONFIG_X86_PAE
 	/*
-	 * The top level points to the linear page table pages above.
-	 * We setup the identity and linear mappings here.
+	 * Make the Guest PMD entries point to the corresponding place in the
+	 * linear mapping (up to one page worth of PMD).
 	 */
-#ifdef CONFIG_X86_PAE
 	for (i = j = 0; i < mapped_pages && j < PTRS_PER_PMD;
 	     i += PTRS_PER_PTE, j++) {
+		/* FIXME: native_set_pmd is overkill here. */
 		native_set_pmd(&pmd, __pmd(((unsigned long)(linear + i)
 		- mem_base) | _PAGE_PRESENT | _PAGE_RW | _PAGE_USER));
 
@@ -971,18 +991,36 @@ static unsigned long setup_pagetables(struct lguest *lg,
 			return -EFAULT;
 	}
 
+	/* One PGD entry, pointing to that PMD page. */
 	set_pgd(&pgd, __pgd(((u32)pmds - mem_base) | _PAGE_PRESENT));
+	/* Copy it in as the first PGD entry (ie. addresses 0-1G). */
 	if (copy_to_user(&pgdir[0], &pgd, sizeof(pgd)) != 0)
 		return -EFAULT;
+	/*
+	 * And the third PGD entry (ie. addresses 3G-4G).
+	 *
+	 * FIXME: This assumes that PAGE_OFFSET for the Guest is 0xC0000000.
+	 */
 	if (copy_to_user(&pgdir[3], &pgd, sizeof(pgd)) != 0)
 		return -EFAULT;
 #else
+	/*
+	 * The top level points to the linear page table pages above.
+	 * We setup the identity and linear mappings here.
+	 */
 	phys_linear = (unsigned long)linear - mem_base;
 	for (i = 0; i < mapped_pages; i += PTRS_PER_PTE) {
 		pgd_t pgd;
+		/*
+		 * Create a PGD entry which points to the right part of the
+		 * linear PTE pages.
+		 */
 		pgd = __pgd((phys_linear + i * sizeof(pte_t)) |
 			    (_PAGE_PRESENT | _PAGE_RW | _PAGE_USER));
 
+		/*
+		 * Copy it into the PGD page at 0 and PAGE_OFFSET.
+		 */
 		if (copy_to_user(&pgdir[i / PTRS_PER_PTE], &pgd, sizeof(pgd))
 		    || copy_to_user(&pgdir[pgd_index(PAGE_OFFSET)
 					   + i / PTRS_PER_PTE],
@@ -992,8 +1030,8 @@ static unsigned long setup_pagetables(struct lguest *lg,
 #endif
 
 	/*
-	 * We return the top level (guest-physical) address: remember where
-	 * this is.
+	 * We return the top level (guest-physical) address: we remember where
+	 * this is to write it into lguest_data when the Guest initializes.
 	 */
 	return (unsigned long)pgdir - mem_base;
 }
@@ -1031,7 +1069,9 @@ int init_guest_pagetable(struct lguest *lg)
 	lg->pgdirs[0].pgdir = (pgd_t *)get_zeroed_page(GFP_KERNEL);
 	if (!lg->pgdirs[0].pgdir)
 		return -ENOMEM;
+
 #ifdef CONFIG_X86_PAE
+	/* For PAE, we also create the initial mid-level. */
 	pgd = lg->pgdirs[0].pgdir;
 	pmd_table = (pmd_t *) get_zeroed_page(GFP_KERNEL);
 	if (!pmd_table)
@@ -1040,11 +1080,13 @@ int init_guest_pagetable(struct lguest *lg)
 	set_pgd(pgd + SWITCHER_PGD_INDEX,
 		__pgd(__pa(pmd_table) | _PAGE_PRESENT));
 #endif
+
+	/* This is the current page table. */
 	lg->cpus[0].cpu_pgd = 0;
 	return 0;
 }
 
-/* When the Guest calls LHCALL_LGUEST_INIT we do more setup. */
+/*H:508 When the Guest calls LHCALL_LGUEST_INIT we do more setup. */
 void page_table_guest_data_init(struct lg_cpu *cpu)
 {
 	/* We get the kernel address: above this is all kernel memory. */
@@ -1105,12 +1147,16 @@ void map_switcher_in_guest(struct lg_cpu *cpu, struct lguest_pages *pages)
 	pmd_t switcher_pmd;
 	pmd_t *pmd_table;
 
+	/* FIXME: native_set_pmd is overkill here. */
 	native_set_pmd(&switcher_pmd, pfn_pmd(__pa(switcher_pte_page) >>
 		       PAGE_SHIFT, PAGE_KERNEL_EXEC));
 
+	/* Figure out where the pmd page is, by reading the PGD, and converting
+	 * it to a virtual address. */
 	pmd_table = __va(pgd_pfn(cpu->lg->
 			pgdirs[cpu->cpu_pgd].pgdir[SWITCHER_PGD_INDEX])
 								<< PAGE_SHIFT);
+	/* Now write it into the shadow page table. */
 	native_set_pmd(&pmd_table[SWITCHER_PMD_INDEX], switcher_pmd);
 #else
 	pgd_t switcher_pgd;
diff --git a/drivers/lguest/x86/core.c b/drivers/lguest/x86/core.c
index 96f7d88ec7f..6ae388849a3 100644
--- a/drivers/lguest/x86/core.c
+++ b/drivers/lguest/x86/core.c
@@ -187,7 +187,7 @@ static void run_guest_once(struct lg_cpu *cpu, struct lguest_pages *pages)
  * also simplify copy_in_guest_info().  Note that we'd still need to restore
  * things when we exit to Launcher userspace, but that's fairly easy.
  *
- * We could also try using this hooks for PGE, but that might be too expensive.
+ * We could also try using these hooks for PGE, but that might be too expensive.
  *
  * The hooks were designed for KVM, but we can also put them to good use.
 :*/
diff --git a/drivers/lguest/x86/switcher_32.S b/drivers/lguest/x86/switcher_32.S
index 6dec0979383..40634b0db9f 100644
--- a/drivers/lguest/x86/switcher_32.S
+++ b/drivers/lguest/x86/switcher_32.S
@@ -1,7 +1,7 @@
 /*P:900
- * This is the Switcher: code which sits at 0xFFC00000 astride both the
- * Host and Guest to do the low-level Guest<->Host switch.  It is as simple as
- * it can be made, but it's naturally very specific to x86.
+ * This is the Switcher: code which sits at 0xFFC00000 (or 0xFFE00000) astride
+ * both the Host and Guest to do the low-level Guest<->Host switch.  It is as
+ * simple as it can be made, but it's naturally very specific to x86.
  *
  * You have now completed Preparation.  If this has whet your appetite; if you
  * are feeling invigorated and refreshed then the next, more challenging stage
-- 
GitLab


From 1842f23c05b6a866be831aa60bc8a8731c58ddd0 Mon Sep 17 00:00:00 2001
From: Rusty Russell <rusty@rustcorp.com.au>
Date: Thu, 30 Jul 2009 16:03:46 -0600
Subject: [PATCH 0310/1153] lguest and virtio: cleanup struct definitions to
 Linux style.

I've been doing this for years, and akpm picked me up on it about 12
months ago.  lguest partly serves as example code, so let's do it Right.

Also, remove two unused fields in struct vblk_info in the example launcher.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
---
 Documentation/lguest/lguest.c  | 21 +++++----------------
 drivers/lguest/lg.h            |  9 +++------
 drivers/lguest/lguest_device.c |  3 +--
 include/linux/lguest.h         |  3 +--
 include/linux/virtio_blk.h     |  6 ++----
 include/linux/virtio_config.h  |  3 +--
 include/linux/virtio_net.h     |  6 ++----
 include/linux/virtio_ring.h    | 12 ++++--------
 8 files changed, 19 insertions(+), 44 deletions(-)

diff --git a/Documentation/lguest/lguest.c b/Documentation/lguest/lguest.c
index 45163651b51..950cde6d6e5 100644
--- a/Documentation/lguest/lguest.c
+++ b/Documentation/lguest/lguest.c
@@ -93,8 +93,7 @@ static int lguest_fd;
 static unsigned int __thread cpu_id;
 
 /* This is our list of devices. */
-struct device_list
-{
+struct device_list {
 	/* Counter to assign interrupt numbers. */
 	unsigned int next_irq;
 
@@ -114,8 +113,7 @@ struct device_list
 static struct device_list devices;
 
 /* The device structure describes a single device. */
-struct device
-{
+struct device {
 	/* The linked-list pointer. */
 	struct device *next;
 
@@ -140,8 +138,7 @@ struct device
 };
 
 /* The virtqueue structure describes a queue attached to a device. */
-struct virtqueue
-{
+struct virtqueue {
 	struct virtqueue *next;
 
 	/* Which device owns me. */
@@ -779,8 +776,7 @@ static void add_used_and_trigger(struct virtqueue *vq, unsigned head, int len)
  *
  * We associate some data with the console for our exit hack.
  */
-struct console_abort
-{
+struct console_abort {
 	/* How many times have they hit ^C? */
 	int count;
 	/* When did they start? */
@@ -1570,20 +1566,13 @@ static void setup_tun_net(char *arg)
 /*:*/
 
 /* This hangs off device->priv. */
-struct vblk_info
-{
+struct vblk_info {
 	/* The size of the file. */
 	off64_t len;
 
 	/* The file descriptor for the file. */
 	int fd;
 
-	/* IO thread listens on this file descriptor [0]. */
-	int workpipe[2];
-
-	/* IO thread writes to this file descriptor to mark it done, then
-	 * Launcher triggers interrupt to Guest. */
-	int done_fd;
 };
 
 /*L:210
diff --git a/drivers/lguest/lg.h b/drivers/lguest/lg.h
index 74c0db691b5..bc28745d05a 100644
--- a/drivers/lguest/lg.h
+++ b/drivers/lguest/lg.h
@@ -16,15 +16,13 @@
 void free_pagetables(void);
 int init_pagetables(struct page **switcher_page, unsigned int pages);
 
-struct pgdir
-{
+struct pgdir {
 	unsigned long gpgdir;
 	pgd_t *pgdir;
 };
 
 /* We have two pages shared with guests, per cpu.  */
-struct lguest_pages
-{
+struct lguest_pages {
 	/* This is the stack page mapped rw in guest */
 	char spare[PAGE_SIZE - sizeof(struct lguest_regs)];
 	struct lguest_regs regs;
@@ -89,8 +87,7 @@ struct lg_eventfd_map {
 };
 
 /* The private info the thread maintains about the guest. */
-struct lguest
-{
+struct lguest {
 	struct lguest_data __user *lguest_data;
 	struct lg_cpu cpus[NR_CPUS];
 	unsigned int nr_cpus;
diff --git a/drivers/lguest/lguest_device.c b/drivers/lguest/lguest_device.c
index 1401c1ace1e..b6200bc39b5 100644
--- a/drivers/lguest/lguest_device.c
+++ b/drivers/lguest/lguest_device.c
@@ -207,8 +207,7 @@ static void lg_reset(struct virtio_device *vdev)
  */
 
 /*D:140 This is the information we remember about each virtqueue. */
-struct lguest_vq_info
-{
+struct lguest_vq_info {
 	/* A copy of the information contained in the device config. */
 	struct lguest_vqconfig config;
 
diff --git a/include/linux/lguest.h b/include/linux/lguest.h
index 0a3a11afd64..2fb1dcbcb5a 100644
--- a/include/linux/lguest.h
+++ b/include/linux/lguest.h
@@ -18,8 +18,7 @@
  * lguest_data".  Once the Guest's initialization hypercall tells the Host where
  * this is, the Guest and Host both publish information in it.
 :*/
-struct lguest_data
-{
+struct lguest_data {
 	/*
 	 * 512 == enabled (same as eflags in normal hardware).  The Guest
 	 * changes interrupts so often that a hypercall is too slow.
diff --git a/include/linux/virtio_blk.h b/include/linux/virtio_blk.h
index be7d255fc7c..8dab9f2b883 100644
--- a/include/linux/virtio_blk.h
+++ b/include/linux/virtio_blk.h
@@ -20,8 +20,7 @@
 
 #define VIRTIO_BLK_ID_BYTES	(sizeof(__u16[256]))	/* IDENTIFY DATA */
 
-struct virtio_blk_config
-{
+struct virtio_blk_config {
 	/* The capacity (in 512-byte sectors). */
 	__u64 capacity;
 	/* The maximum segment size (if VIRTIO_BLK_F_SIZE_MAX) */
@@ -50,8 +49,7 @@ struct virtio_blk_config
 #define VIRTIO_BLK_T_BARRIER	0x80000000
 
 /* This is the first element of the read scatter-gather list. */
-struct virtio_blk_outhdr
-{
+struct virtio_blk_outhdr {
 	/* VIRTIO_BLK_T* */
 	__u32 type;
 	/* io priority. */
diff --git a/include/linux/virtio_config.h b/include/linux/virtio_config.h
index 99f514575f6..e547e3c8ee9 100644
--- a/include/linux/virtio_config.h
+++ b/include/linux/virtio_config.h
@@ -79,8 +79,7 @@
  *	the dev->feature bits if it wants.
  */
 typedef void vq_callback_t(struct virtqueue *);
-struct virtio_config_ops
-{
+struct virtio_config_ops {
 	void (*get)(struct virtio_device *vdev, unsigned offset,
 		    void *buf, unsigned len);
 	void (*set)(struct virtio_device *vdev, unsigned offset,
diff --git a/include/linux/virtio_net.h b/include/linux/virtio_net.h
index 9c543d6ac53..d8dd539c9f4 100644
--- a/include/linux/virtio_net.h
+++ b/include/linux/virtio_net.h
@@ -31,8 +31,7 @@
 
 #define VIRTIO_NET_S_LINK_UP	1	/* Link is up */
 
-struct virtio_net_config
-{
+struct virtio_net_config {
 	/* The config defining mac address (if VIRTIO_NET_F_MAC) */
 	__u8 mac[6];
 	/* See VIRTIO_NET_F_STATUS and VIRTIO_NET_S_* above */
@@ -41,8 +40,7 @@ struct virtio_net_config
 
 /* This is the first element of the scatter-gather list.  If you don't
  * specify GSO or CSUM features, you can simply ignore the header. */
-struct virtio_net_hdr
-{
+struct virtio_net_hdr {
 #define VIRTIO_NET_HDR_F_NEEDS_CSUM	1	// Use csum_start, csum_offset
 	__u8 flags;
 #define VIRTIO_NET_HDR_GSO_NONE		0	// Not a GSO frame
diff --git a/include/linux/virtio_ring.h b/include/linux/virtio_ring.h
index 693e0ec5afa..e4d144b132b 100644
--- a/include/linux/virtio_ring.h
+++ b/include/linux/virtio_ring.h
@@ -30,8 +30,7 @@
 #define VIRTIO_RING_F_INDIRECT_DESC	28
 
 /* Virtio ring descriptors: 16 bytes.  These can chain together via "next". */
-struct vring_desc
-{
+struct vring_desc {
 	/* Address (guest-physical). */
 	__u64 addr;
 	/* Length. */
@@ -42,24 +41,21 @@ struct vring_desc
 	__u16 next;
 };
 
-struct vring_avail
-{
+struct vring_avail {
 	__u16 flags;
 	__u16 idx;
 	__u16 ring[];
 };
 
 /* u32 is used here for ids for padding reasons. */
-struct vring_used_elem
-{
+struct vring_used_elem {
 	/* Index of start of used descriptor chain. */
 	__u32 id;
 	/* Total length of the descriptor chain which was used (written to) */
 	__u32 len;
 };
 
-struct vring_used
-{
+struct vring_used {
 	__u16 flags;
 	__u16 idx;
 	struct vring_used_elem ring[];
-- 
GitLab


From e624859e7eb6ae2930df3923af73406dc6ccdad8 Mon Sep 17 00:00:00 2001
From: Linus Walleij <linus.walleij@stericsson.com>
Date: Mon, 27 Jul 2009 22:11:59 +0100
Subject: [PATCH 0311/1153] ARM: 5624/1: Document cache aliasing region

Augment the memory.txt file for ARM to list the cache aliasing
region ffff4000-fffffff.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 Documentation/arm/memory.txt | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/arm/memory.txt b/Documentation/arm/memory.txt
index 43cb1004d35..9d58c7c5edd 100644
--- a/Documentation/arm/memory.txt
+++ b/Documentation/arm/memory.txt
@@ -21,6 +21,8 @@ ffff8000	ffffffff	copy_user_page / clear_user_page use.
 				For SA11xx and Xscale, this is used to
 				setup a minicache mapping.
 
+ffff4000	ffffffff	cache aliasing on ARMv6 and later CPUs.
+
 ffff1000	ffff7fff	Reserved.
 				Platforms must not use this address range.
 
-- 
GitLab


From 3ef7143d2287b21e09e00a25a8cb4fbdcf0c6c4c Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= <u.kleine-koenig@pengutronix.de>
Date: Wed, 29 Jul 2009 19:31:30 +0100
Subject: [PATCH 0312/1153] ARM: 5627/1: Fix restoring of lr at the end of
 mcount
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

After ftrace_trace_function is called r1 is probably clobbered so don't
try to use its value for restoring.

This was introduced in v2.6.29~38^2~7

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/kernel/entry-common.S | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S
index 366e5097a41..8c3de1a350b 100644
--- a/arch/arm/kernel/entry-common.S
+++ b/arch/arm/kernel/entry-common.S
@@ -148,7 +148,7 @@ trace:
 	sub r0, r0, #MCOUNT_INSN_SIZE
 	mov lr, pc
 	mov pc, r2
-	mov lr, r1				@ restore lr
+	ldr lr, [fp, #-4]			@ restore lr
 	ldmia sp!, {r0-r3, pc}
 
 #endif /* CONFIG_DYNAMIC_FTRACE */
-- 
GitLab


From 320145fac91955ee35a6af7e1c2b42388a17b3d8 Mon Sep 17 00:00:00 2001
From: Yegor Yefremov <yegorslists@googlemail.com>
Date: Thu, 9 Jul 2009 08:48:03 +0100
Subject: [PATCH 0313/1153] ARM: 5597/1: [PCI] reset all internal hardware
 prior PCI initialization

Make software reset to avoid freeze if PCI bus was messed up

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-ks8695/pci.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/mach-ks8695/pci.c b/arch/arm/mach-ks8695/pci.c
index f5ebcc0fcab..78499667eb7 100644
--- a/arch/arm/mach-ks8695/pci.c
+++ b/arch/arm/mach-ks8695/pci.c
@@ -245,6 +245,9 @@ static int ks8695_pci_fault(unsigned long addr, unsigned int fsr, struct pt_regs
 
 static void __init ks8695_pci_preinit(void)
 {
+	/* make software reset to avoid freeze if PCI bus was messed up */
+	__raw_writel(0x80000000, KS8695_PCI_VA + KS8695_PBCS);
+
 	/* stage 1 initialization, subid, subdevice = 0x0001 */
 	__raw_writel(0x00010001, KS8695_PCI_VA + KS8695_CRCSID);
 
-- 
GitLab


From 2163b1e616c41c286f5ab79912671cd4bf52057c Mon Sep 17 00:00:00 2001
From: Steven Whitehouse <swhiteho@redhat.com>
Date: Thu, 25 Jun 2009 16:30:26 +0100
Subject: [PATCH 0314/1153] GFS2: Shrink the shrinker

This patch removes some of the special cases that the shrinker
was trying to deal with. As a result we leave fewer items on
the list and none at all which cannot be demoted. This makes
the list scanning more efficient and solves some issues seen
with large numbers of inodes.

Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
---
 fs/gfs2/glock.c | 23 +++++------------------
 1 file changed, 5 insertions(+), 18 deletions(-)

diff --git a/fs/gfs2/glock.c b/fs/gfs2/glock.c
index 297421c0427..fdb796c4f94 100644
--- a/fs/gfs2/glock.c
+++ b/fs/gfs2/glock.c
@@ -1300,7 +1300,6 @@ static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask)
 	struct gfs2_glock *gl;
 	int may_demote;
 	int nr_skipped = 0;
-	int got_ref = 0;
 	LIST_HEAD(skipped);
 
 	if (nr == 0)
@@ -1318,7 +1317,6 @@ static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask)
 		/* Test for being demotable */
 		if (!test_and_set_bit(GLF_LOCK, &gl->gl_flags)) {
 			gfs2_glock_hold(gl);
-			got_ref = 1;
 			spin_unlock(&lru_lock);
 			spin_lock(&gl->gl_spin);
 			may_demote = demote_ok(gl);
@@ -1327,25 +1325,14 @@ static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask)
 			if (may_demote) {
 				handle_callback(gl, LM_ST_UNLOCKED, 0);
 				nr--;
-				if (queue_delayed_work(glock_workqueue, &gl->gl_work, 0) == 0)
-					gfs2_glock_put(gl);
-				got_ref = 0;
 			}
+			if (queue_delayed_work(glock_workqueue, &gl->gl_work, 0) == 0)
+				gfs2_glock_put(gl);
 			spin_lock(&lru_lock);
-			if (may_demote)
-				continue;
-		}
-		if (list_empty(&gl->gl_lru) &&
-		    (atomic_read(&gl->gl_ref) <= (2 + got_ref))) {
-			nr_skipped++;
-			list_add(&gl->gl_lru, &skipped);
-		}
-		if (got_ref) {
-			spin_unlock(&lru_lock);
-			gfs2_glock_put(gl);
-			spin_lock(&lru_lock);
-			got_ref = 0;
+			continue;
 		}
+		nr_skipped++;
+		list_add(&gl->gl_lru, &skipped);
 	}
 	list_splice(&skipped, &lru_list);
 	atomic_add(nr_skipped, &lru_count);
-- 
GitLab


From 1946f70ab5e4eb8b54a8eaaedba2293a3750ab7e Mon Sep 17 00:00:00 2001
From: Benjamin Marzinski <bmarzins@redhat.com>
Date: Thu, 25 Jun 2009 15:09:51 -0500
Subject: [PATCH 0315/1153] GFS2: keep statfs info in sync on grows

GFS2 wasn't syncing its statfs info on grows.  This causes a problem
when you grow the filesystem on multiple nodes.  GFS2 would calculate
the new space based on the resource groups (which are always current),
and then assume that the filesystem had grown the from the existing
statfs size.  If you grew the filesystem on two different nodes in a
short time, the second node wouldn't see the statfs size change from the
first node, and would assume that it was grown by a larger amount than
it was.  When all these changes were synced out, the total fileystem
size would be incorrect (the first grow would be counted twice).

This patch syncs makes GFS2 read in the statfs changes from disk before
a grow, and write them out after the grow, while the master statfs inode
is locked.

Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
---
 fs/gfs2/aops.c  | 39 +++++++++++++++++++++++++++++++++++++++
 fs/gfs2/super.c | 39 +++++++++++++++++++++++++--------------
 fs/gfs2/super.h |  4 ++++
 3 files changed, 68 insertions(+), 14 deletions(-)

diff --git a/fs/gfs2/aops.c b/fs/gfs2/aops.c
index 03ebb439ace..7ebae9a4ecc 100644
--- a/fs/gfs2/aops.c
+++ b/fs/gfs2/aops.c
@@ -624,6 +624,7 @@ static int gfs2_write_begin(struct file *file, struct address_space *mapping,
 {
 	struct gfs2_inode *ip = GFS2_I(mapping->host);
 	struct gfs2_sbd *sdp = GFS2_SB(mapping->host);
+	struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode);
 	unsigned int data_blocks = 0, ind_blocks = 0, rblocks;
 	int alloc_required;
 	int error = 0;
@@ -637,6 +638,14 @@ static int gfs2_write_begin(struct file *file, struct address_space *mapping,
 	error = gfs2_glock_nq(&ip->i_gh);
 	if (unlikely(error))
 		goto out_uninit;
+	if (&ip->i_inode == sdp->sd_rindex) {
+		error = gfs2_glock_nq_init(m_ip->i_gl, LM_ST_EXCLUSIVE,
+					   GL_NOCACHE, &m_ip->i_gh);
+		if (unlikely(error)) {
+			gfs2_glock_dq(&ip->i_gh);
+			goto out_uninit;
+		}
+	}
 
 	error = gfs2_write_alloc_required(ip, pos, len, &alloc_required);
 	if (error)
@@ -667,6 +676,8 @@ static int gfs2_write_begin(struct file *file, struct address_space *mapping,
 		rblocks += data_blocks ? data_blocks : 1;
 	if (ind_blocks || data_blocks)
 		rblocks += RES_STATFS + RES_QUOTA;
+	if (&ip->i_inode == sdp->sd_rindex)
+		rblocks += 2 * RES_STATFS;
 
 	error = gfs2_trans_begin(sdp, rblocks,
 				 PAGE_CACHE_SIZE/sdp->sd_sb.sb_bsize);
@@ -712,6 +723,10 @@ out_alloc_put:
 		gfs2_alloc_put(ip);
 	}
 out_unlock:
+	if (&ip->i_inode == sdp->sd_rindex) {
+		gfs2_glock_dq(&m_ip->i_gh);
+		gfs2_holder_uninit(&m_ip->i_gh);
+	}
 	gfs2_glock_dq(&ip->i_gh);
 out_uninit:
 	gfs2_holder_uninit(&ip->i_gh);
@@ -725,14 +740,21 @@ out_uninit:
 static void adjust_fs_space(struct inode *inode)
 {
 	struct gfs2_sbd *sdp = inode->i_sb->s_fs_info;
+	struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode);
+	struct gfs2_inode *l_ip = GFS2_I(sdp->sd_sc_inode);
 	struct gfs2_statfs_change_host *m_sc = &sdp->sd_statfs_master;
 	struct gfs2_statfs_change_host *l_sc = &sdp->sd_statfs_local;
+	struct buffer_head *m_bh, *l_bh;
 	u64 fs_total, new_free;
 
 	/* Total up the file system space, according to the latest rindex. */
 	fs_total = gfs2_ri_total(sdp);
+	if (gfs2_meta_inode_buffer(m_ip, &m_bh) != 0)
+		return;
 
 	spin_lock(&sdp->sd_statfs_spin);
+	gfs2_statfs_change_in(m_sc, m_bh->b_data +
+			      sizeof(struct gfs2_dinode));
 	if (fs_total > (m_sc->sc_total + l_sc->sc_total))
 		new_free = fs_total - (m_sc->sc_total + l_sc->sc_total);
 	else
@@ -741,6 +763,13 @@ static void adjust_fs_space(struct inode *inode)
 	fs_warn(sdp, "File system extended by %llu blocks.\n",
 		(unsigned long long)new_free);
 	gfs2_statfs_change(sdp, new_free, new_free, 0);
+
+	if (gfs2_meta_inode_buffer(l_ip, &l_bh) != 0)
+		goto out;
+	update_statfs(sdp, m_bh, l_bh);
+	brelse(l_bh);
+out:
+	brelse(m_bh);
 }
 
 /**
@@ -763,6 +792,7 @@ static int gfs2_stuffed_write_end(struct inode *inode, struct buffer_head *dibh,
 {
 	struct gfs2_inode *ip = GFS2_I(inode);
 	struct gfs2_sbd *sdp = GFS2_SB(inode);
+	struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode);
 	u64 to = pos + copied;
 	void *kaddr;
 	unsigned char *buf = dibh->b_data + sizeof(struct gfs2_dinode);
@@ -794,6 +824,10 @@ static int gfs2_stuffed_write_end(struct inode *inode, struct buffer_head *dibh,
 
 	brelse(dibh);
 	gfs2_trans_end(sdp);
+	if (inode == sdp->sd_rindex) {
+		gfs2_glock_dq(&m_ip->i_gh);
+		gfs2_holder_uninit(&m_ip->i_gh);
+	}
 	gfs2_glock_dq(&ip->i_gh);
 	gfs2_holder_uninit(&ip->i_gh);
 	return copied;
@@ -823,6 +857,7 @@ static int gfs2_write_end(struct file *file, struct address_space *mapping,
 	struct inode *inode = page->mapping->host;
 	struct gfs2_inode *ip = GFS2_I(inode);
 	struct gfs2_sbd *sdp = GFS2_SB(inode);
+	struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode);
 	struct buffer_head *dibh;
 	struct gfs2_alloc *al = ip->i_alloc;
 	unsigned int from = pos & (PAGE_CACHE_SIZE - 1);
@@ -865,6 +900,10 @@ failed:
 		gfs2_quota_unlock(ip);
 		gfs2_alloc_put(ip);
 	}
+	if (inode == sdp->sd_rindex) {
+		gfs2_glock_dq(&m_ip->i_gh);
+		gfs2_holder_uninit(&m_ip->i_gh);
+	}
 	gfs2_glock_dq(&ip->i_gh);
 	gfs2_holder_uninit(&ip->i_gh);
 	return ret;
diff --git a/fs/gfs2/super.c b/fs/gfs2/super.c
index 0a680133647..552e321cee5 100644
--- a/fs/gfs2/super.c
+++ b/fs/gfs2/super.c
@@ -353,7 +353,7 @@ fail:
 	return error;
 }
 
-static void gfs2_statfs_change_in(struct gfs2_statfs_change_host *sc, const void *buf)
+void gfs2_statfs_change_in(struct gfs2_statfs_change_host *sc, const void *buf)
 {
 	const struct gfs2_statfs_change *str = buf;
 
@@ -441,6 +441,29 @@ void gfs2_statfs_change(struct gfs2_sbd *sdp, s64 total, s64 free,
 	brelse(l_bh);
 }
 
+void update_statfs(struct gfs2_sbd *sdp, struct buffer_head *m_bh,
+		   struct buffer_head *l_bh)
+{
+	struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode);
+	struct gfs2_inode *l_ip = GFS2_I(sdp->sd_sc_inode);
+	struct gfs2_statfs_change_host *m_sc = &sdp->sd_statfs_master;
+	struct gfs2_statfs_change_host *l_sc = &sdp->sd_statfs_local;
+
+	gfs2_trans_add_bh(l_ip->i_gl, l_bh, 1);
+
+	spin_lock(&sdp->sd_statfs_spin);
+	m_sc->sc_total += l_sc->sc_total;
+	m_sc->sc_free += l_sc->sc_free;
+	m_sc->sc_dinodes += l_sc->sc_dinodes;
+	memset(l_sc, 0, sizeof(struct gfs2_statfs_change));
+	memset(l_bh->b_data + sizeof(struct gfs2_dinode),
+	       0, sizeof(struct gfs2_statfs_change));
+	spin_unlock(&sdp->sd_statfs_spin);
+
+	gfs2_trans_add_bh(m_ip->i_gl, m_bh, 1);
+	gfs2_statfs_change_out(m_sc, m_bh->b_data + sizeof(struct gfs2_dinode));
+}
+
 int gfs2_statfs_sync(struct gfs2_sbd *sdp)
 {
 	struct gfs2_inode *m_ip = GFS2_I(sdp->sd_statfs_inode);
@@ -477,19 +500,7 @@ int gfs2_statfs_sync(struct gfs2_sbd *sdp)
 	if (error)
 		goto out_bh2;
 
-	gfs2_trans_add_bh(l_ip->i_gl, l_bh, 1);
-
-	spin_lock(&sdp->sd_statfs_spin);
-	m_sc->sc_total += l_sc->sc_total;
-	m_sc->sc_free += l_sc->sc_free;
-	m_sc->sc_dinodes += l_sc->sc_dinodes;
-	memset(l_sc, 0, sizeof(struct gfs2_statfs_change));
-	memset(l_bh->b_data + sizeof(struct gfs2_dinode),
-	       0, sizeof(struct gfs2_statfs_change));
-	spin_unlock(&sdp->sd_statfs_spin);
-
-	gfs2_trans_add_bh(m_ip->i_gl, m_bh, 1);
-	gfs2_statfs_change_out(m_sc, m_bh->b_data + sizeof(struct gfs2_dinode));
+	update_statfs(sdp, m_bh, l_bh);
 
 	gfs2_trans_end(sdp);
 
diff --git a/fs/gfs2/super.h b/fs/gfs2/super.h
index b56413e3e40..22e0417ed99 100644
--- a/fs/gfs2/super.h
+++ b/fs/gfs2/super.h
@@ -40,6 +40,10 @@ extern int gfs2_make_fs_rw(struct gfs2_sbd *sdp);
 extern int gfs2_statfs_init(struct gfs2_sbd *sdp);
 extern void gfs2_statfs_change(struct gfs2_sbd *sdp, s64 total, s64 free,
 			       s64 dinodes);
+extern void gfs2_statfs_change_in(struct gfs2_statfs_change_host *sc,
+				  const void *buf);
+extern void update_statfs(struct gfs2_sbd *sdp, struct buffer_head *m_bh,
+			  struct buffer_head *l_bh);
 extern int gfs2_statfs_sync(struct gfs2_sbd *sdp);
 
 extern int gfs2_freeze_fs(struct gfs2_sbd *sdp);
-- 
GitLab


From a51b56fff3f04fc5aa66b21a2a6d693ee9862d66 Mon Sep 17 00:00:00 2001
From: Benjamin Marzinski <bmarzins@redhat.com>
Date: Tue, 30 Jun 2009 13:51:11 -0500
Subject: [PATCH 0316/1153] GFS2: Fix panic in glock memory shrinker

It is possible for gfs2_shrink_glock_memory() to check a glock for
demotion
that's in the process of being freed by gfs2_glock_put().  In this case,
gfs2_shrink_glock_memory() will acquire a new reference to this glock,
and
then try to free the glock itself when it drops the refernce.  To solve
this, gfs2_shrink_glock_memory() just needs to check if the glock is in
the process of being freed, and if so skip it without ever unlocking the
lru_lock.

Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Acked-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
---
 fs/gfs2/glock.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/fs/gfs2/glock.c b/fs/gfs2/glock.c
index fdb796c4f94..827136ee794 100644
--- a/fs/gfs2/glock.c
+++ b/fs/gfs2/glock.c
@@ -1314,6 +1314,10 @@ static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask)
 		list_del_init(&gl->gl_lru);
 		atomic_dec(&lru_count);
 
+		/* Check if glock is about to be freed */
+		if (atomic_read(&gl->gl_ref) == 0)
+			continue;
+
 		/* Test for being demotable */
 		if (!test_and_set_bit(GLF_LOCK, &gl->gl_flags)) {
 			gfs2_glock_hold(gl);
-- 
GitLab


From 1e19a19584b332eb92a573b66b7342fb97e67507 Mon Sep 17 00:00:00 2001
From: Steven Whitehouse <swhiteho@redhat.com>
Date: Fri, 10 Jul 2009 21:13:38 +0100
Subject: [PATCH 0317/1153] GFS2: Don't try and dealloc own inode

When searching for unlinked, but still allocated inodes during block
allocation, avoid the block relating to the inode that is doing the
allocation. This fixes a hang caused when an unlinked, but still
open, inode tries to allocate some more blocks and lands up
finding itself during the search for deallocatable inodes.

Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
---
 fs/gfs2/rgrp.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/fs/gfs2/rgrp.c b/fs/gfs2/rgrp.c
index daa4ae341a2..5e5074176da 100644
--- a/fs/gfs2/rgrp.c
+++ b/fs/gfs2/rgrp.c
@@ -961,7 +961,8 @@ static int try_rgrp_fit(struct gfs2_rgrpd *rgd, struct gfs2_alloc *al)
  * Returns: The inode, if one has been found
  */
 
-static struct inode *try_rgrp_unlink(struct gfs2_rgrpd *rgd, u64 *last_unlinked)
+static struct inode *try_rgrp_unlink(struct gfs2_rgrpd *rgd, u64 *last_unlinked,
+				     u64 skip)
 {
 	struct inode *inode;
 	u32 goal = 0, block;
@@ -985,6 +986,8 @@ static struct inode *try_rgrp_unlink(struct gfs2_rgrpd *rgd, u64 *last_unlinked)
 		goal++;
 		if (*last_unlinked != NO_BLOCK && no_addr <= *last_unlinked)
 			continue;
+		if (no_addr == skip)
+			continue;
 		*last_unlinked = no_addr;
 		inode = gfs2_inode_lookup(rgd->rd_sbd->sd_vfs, DT_UNKNOWN,
 					  no_addr, -1, 1);
@@ -1104,7 +1107,7 @@ static struct inode *get_local_rgrp(struct gfs2_inode *ip, u64 *last_unlinked)
 			if (try_rgrp_fit(rgd, al))
 				goto out;
 			if (rgd->rd_flags & GFS2_RDF_CHECK)
-				inode = try_rgrp_unlink(rgd, last_unlinked);
+				inode = try_rgrp_unlink(rgd, last_unlinked, ip->i_no_addr);
 			if (!rg_locked)
 				gfs2_glock_dq_uninit(&al->al_rgd_gh);
 			if (inode)
@@ -1138,7 +1141,7 @@ static struct inode *get_local_rgrp(struct gfs2_inode *ip, u64 *last_unlinked)
 			if (try_rgrp_fit(rgd, al))
 				goto out;
 			if (rgd->rd_flags & GFS2_RDF_CHECK)
-				inode = try_rgrp_unlink(rgd, last_unlinked);
+				inode = try_rgrp_unlink(rgd, last_unlinked, ip->i_no_addr);
 			if (!rg_locked)
 				gfs2_glock_dq_uninit(&al->al_rgd_gh);
 			if (inode)
-- 
GitLab


From 8ff22a6f9bdaac87c0eeb1d56c736181f11b4221 Mon Sep 17 00:00:00 2001
From: Benjamin Marzinski <bmarzins@redhat.com>
Date: Fri, 10 Jul 2009 18:04:24 -0500
Subject: [PATCH 0318/1153] GFS2: Don't put unlikely reclaim candidates on the
 reclaim list.

GFS2 was placing far too many glocks on the reclaim list that were not good
candidates for freeing up from cache.  These locks would sit there and
repeatedly get scanned to see if they could be reclaimed, wasting a lot
of time when there was memory pressure. This fix does more checks on the
locks to see if they are actually likely to be removable from cache.

Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
---
 fs/gfs2/glock.c | 72 +++++++++++++++++++++++++++++++------------------
 1 file changed, 46 insertions(+), 26 deletions(-)

diff --git a/fs/gfs2/glock.c b/fs/gfs2/glock.c
index 827136ee794..f041a89e1ab 100644
--- a/fs/gfs2/glock.c
+++ b/fs/gfs2/glock.c
@@ -173,6 +173,26 @@ static void gfs2_glock_hold(struct gfs2_glock *gl)
 	atomic_inc(&gl->gl_ref);
 }
 
+/**
+ * demote_ok - Check to see if it's ok to unlock a glock
+ * @gl: the glock
+ *
+ * Returns: 1 if it's ok
+ */
+
+static int demote_ok(const struct gfs2_glock *gl)
+{
+	const struct gfs2_glock_operations *glops = gl->gl_ops;
+
+	if (gl->gl_state == LM_ST_UNLOCKED)
+		return 0;
+	if (!list_empty(&gl->gl_holders))
+		return 0;
+	if (glops->go_demote_ok)
+		return glops->go_demote_ok(gl);
+	return 1;
+}
+
 /**
  * gfs2_glock_schedule_for_reclaim - Add a glock to the reclaim list
  * @gl: the glock
@@ -181,14 +201,34 @@ static void gfs2_glock_hold(struct gfs2_glock *gl)
 
 static void gfs2_glock_schedule_for_reclaim(struct gfs2_glock *gl)
 {
+	int may_reclaim;
+	may_reclaim = (demote_ok(gl) &&
+		       (atomic_read(&gl->gl_ref) == 1 ||
+			(gl->gl_name.ln_type == LM_TYPE_INODE &&
+			 atomic_read(&gl->gl_ref) <= 2)));
 	spin_lock(&lru_lock);
-	if (list_empty(&gl->gl_lru) && gl->gl_state != LM_ST_UNLOCKED) {
+	if (list_empty(&gl->gl_lru) && may_reclaim) {
 		list_add_tail(&gl->gl_lru, &lru_list);
 		atomic_inc(&lru_count);
 	}
 	spin_unlock(&lru_lock);
 }
 
+/**
+ * gfs2_glock_put_nolock() - Decrement reference count on glock
+ * @gl: The glock to put
+ *
+ * This function should only be used if the caller has its own reference
+ * to the glock, in addition to the one it is dropping.
+ */
+
+static void gfs2_glock_put_nolock(struct gfs2_glock *gl)
+{
+	if (atomic_dec_and_test(&gl->gl_ref))
+		GLOCK_BUG_ON(gl, 1);
+	gfs2_glock_schedule_for_reclaim(gl);
+}
+
 /**
  * gfs2_glock_put() - Decrement reference count on glock
  * @gl: The glock to put
@@ -214,9 +254,9 @@ int gfs2_glock_put(struct gfs2_glock *gl)
 		rv = 1;
 		goto out;
 	}
-	/* 1 for being hashed, 1 for having state != LM_ST_UNLOCKED */
-	if (atomic_read(&gl->gl_ref) == 2)
-		gfs2_glock_schedule_for_reclaim(gl);
+	spin_lock(&gl->gl_spin);
+	gfs2_glock_schedule_for_reclaim(gl);
+	spin_unlock(&gl->gl_spin);
 	write_unlock(gl_lock_addr(gl->gl_hash));
 out:
 	return rv;
@@ -398,7 +438,7 @@ static void state_change(struct gfs2_glock *gl, unsigned int new_state)
 		if (held2)
 			gfs2_glock_hold(gl);
 		else
-			gfs2_glock_put(gl);
+			gfs2_glock_put_nolock(gl);
 	}
 
 	gl->gl_state = new_state;
@@ -633,7 +673,7 @@ out:
 out_sched:
 	gfs2_glock_hold(gl);
 	if (queue_delayed_work(glock_workqueue, &gl->gl_work, 0) == 0)
-		gfs2_glock_put(gl);
+		gfs2_glock_put_nolock(gl);
 out_unlock:
 	clear_bit(GLF_LOCK, &gl->gl_flags);
 	goto out;
@@ -1274,26 +1314,6 @@ void gfs2_glock_complete(struct gfs2_glock *gl, int ret)
 		gfs2_glock_put(gl);
 }
 
-/**
- * demote_ok - Check to see if it's ok to unlock a glock
- * @gl: the glock
- *
- * Returns: 1 if it's ok
- */
-
-static int demote_ok(const struct gfs2_glock *gl)
-{
-	const struct gfs2_glock_operations *glops = gl->gl_ops;
-
-	if (gl->gl_state == LM_ST_UNLOCKED)
-		return 0;
-	if (!list_empty(&gl->gl_holders))
-		return 0;
-	if (glops->go_demote_ok)
-		return glops->go_demote_ok(gl);
-	return 1;
-}
-
 
 static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask)
 {
-- 
GitLab


From 6b94617024bd6810cde1d0d491202c30d5a38d91 Mon Sep 17 00:00:00 2001
From: Benjamin Marzinski <bmarzins@redhat.com>
Date: Fri, 10 Jul 2009 18:13:26 -0500
Subject: [PATCH 0319/1153] GFS2: Fix incorrent statfs consistency check

Since both linked and unlinked inodes are counted by rgd->rd_dinodes, It
makes no sense to count them with the used data blocks (first check that
I changed), it makes sense to count them with the linked inodes (second
check), and it makes no sense to care if there are more unlinked inodes
than linked ones. This fixes these errors.

Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
---
 fs/gfs2/rgrp.c | 14 +++-----------
 1 file changed, 3 insertions(+), 11 deletions(-)

diff --git a/fs/gfs2/rgrp.c b/fs/gfs2/rgrp.c
index 5e5074176da..fba795798d3 100644
--- a/fs/gfs2/rgrp.c
+++ b/fs/gfs2/rgrp.c
@@ -285,27 +285,19 @@ void gfs2_rgrp_verify(struct gfs2_rgrpd *rgd)
 	}
 
 	tmp = rgd->rd_data - rgd->rd_free - rgd->rd_dinodes;
-	if (count[1] + count[2] != tmp) {
+	if (count[1] != tmp) {
 		if (gfs2_consist_rgrpd(rgd))
 			fs_err(sdp, "used data mismatch:  %u != %u\n",
 			       count[1], tmp);
 		return;
 	}
 
-	if (count[3] != rgd->rd_dinodes) {
+	if (count[2] + count[3] != rgd->rd_dinodes) {
 		if (gfs2_consist_rgrpd(rgd))
 			fs_err(sdp, "used metadata mismatch:  %u != %u\n",
-			       count[3], rgd->rd_dinodes);
+			       count[2] + count[3], rgd->rd_dinodes);
 		return;
 	}
-
-	if (count[2] > count[3]) {
-		if (gfs2_consist_rgrpd(rgd))
-			fs_err(sdp, "unlinked inodes > inodes:  %u\n",
-			       count[2]);
-		return;
-	}
-
 }
 
 static inline int rgrp_contains_block(struct gfs2_rgrpd *rgd, u64 block)
-- 
GitLab


From b94a170e96dc416828af9d350ae2e34b70ae7347 Mon Sep 17 00:00:00 2001
From: Benjamin Marzinski <bmarzins@redhat.com>
Date: Thu, 23 Jul 2009 18:52:34 -0500
Subject: [PATCH 0320/1153] GFS2: remove dcache entries for remote deleted
 inodes

When a file is deleted from a gfs2 filesystem on one node, a dcache
entry for it may still exist on other nodes in the cluster. If this
happens, gfs2 will be unable to free this file on disk. Because of this,
it's possible to have a gfs2 filesystem with no files on it and no free
space. With this patch, when a node receives a callback notifying it
that the file is being deleted on another node, it schedules a new
workqueue thread to remove the file's dcache entry.

Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
---
 fs/gfs2/glock.c  | 43 ++++++++++++++++++++++++++++++++++++++-----
 fs/gfs2/glock.h  |  3 +++
 fs/gfs2/glops.c  | 21 +++++++++++++++++++++
 fs/gfs2/incore.h |  2 ++
 fs/gfs2/super.c  |  1 +
 5 files changed, 65 insertions(+), 5 deletions(-)

diff --git a/fs/gfs2/glock.c b/fs/gfs2/glock.c
index f041a89e1ab..8b674b1f3a5 100644
--- a/fs/gfs2/glock.c
+++ b/fs/gfs2/glock.c
@@ -63,6 +63,7 @@ static void do_xmote(struct gfs2_glock *gl, struct gfs2_holder *gh, unsigned int
 static DECLARE_RWSEM(gfs2_umount_flush_sem);
 static struct dentry *gfs2_root;
 static struct workqueue_struct *glock_workqueue;
+struct workqueue_struct *gfs2_delete_workqueue;
 static LIST_HEAD(lru_list);
 static atomic_t lru_count = ATOMIC_INIT(0);
 static DEFINE_SPINLOCK(lru_lock);
@@ -167,7 +168,7 @@ static void glock_free(struct gfs2_glock *gl)
  *
  */
 
-static void gfs2_glock_hold(struct gfs2_glock *gl)
+void gfs2_glock_hold(struct gfs2_glock *gl)
 {
 	GLOCK_BUG_ON(gl, atomic_read(&gl->gl_ref) == 0);
 	atomic_inc(&gl->gl_ref);
@@ -222,7 +223,7 @@ static void gfs2_glock_schedule_for_reclaim(struct gfs2_glock *gl)
  * to the glock, in addition to the one it is dropping.
  */
 
-static void gfs2_glock_put_nolock(struct gfs2_glock *gl)
+void gfs2_glock_put_nolock(struct gfs2_glock *gl)
 {
 	if (atomic_dec_and_test(&gl->gl_ref))
 		GLOCK_BUG_ON(gl, 1);
@@ -679,6 +680,29 @@ out_unlock:
 	goto out;
 }
 
+static void delete_work_func(struct work_struct *work)
+{
+	struct gfs2_glock *gl = container_of(work, struct gfs2_glock, gl_delete);
+	struct gfs2_sbd *sdp = gl->gl_sbd;
+	struct gfs2_inode *ip = NULL;
+	struct inode *inode;
+	u64 no_addr = 0;
+
+	spin_lock(&gl->gl_spin);
+	ip = (struct gfs2_inode *)gl->gl_object;
+	if (ip)
+		no_addr = ip->i_no_addr;
+	spin_unlock(&gl->gl_spin);
+	if (ip) {
+		inode = gfs2_ilookup(sdp->sd_vfs, no_addr);
+		if (inode) {
+			d_prune_aliases(inode);
+			iput(inode);
+		}
+	}
+	gfs2_glock_put(gl);
+}
+
 static void glock_work_func(struct work_struct *work)
 {
 	unsigned long delay = 0;
@@ -757,6 +781,7 @@ int gfs2_glock_get(struct gfs2_sbd *sdp, u64 number,
 	gl->gl_sbd = sdp;
 	gl->gl_aspace = NULL;
 	INIT_DELAYED_WORK(&gl->gl_work, glock_work_func);
+	INIT_WORK(&gl->gl_delete, delete_work_func);
 
 	/* If this glock protects actual on-disk data or metadata blocks,
 	   create a VFS inode to manage the pages/buffers holding them. */
@@ -898,6 +923,8 @@ static void handle_callback(struct gfs2_glock *gl, unsigned int state,
 			gl->gl_demote_state != state) {
 		gl->gl_demote_state = LM_ST_UNLOCKED;
 	}
+	if (gl->gl_ops->go_callback)
+		gl->gl_ops->go_callback(gl);
 	trace_gfs2_demote_rq(gl);
 }
 
@@ -1344,14 +1371,14 @@ static int gfs2_shrink_glock_memory(int nr, gfp_t gfp_mask)
 			spin_unlock(&lru_lock);
 			spin_lock(&gl->gl_spin);
 			may_demote = demote_ok(gl);
-			spin_unlock(&gl->gl_spin);
-			clear_bit(GLF_LOCK, &gl->gl_flags);
 			if (may_demote) {
 				handle_callback(gl, LM_ST_UNLOCKED, 0);
 				nr--;
 			}
 			if (queue_delayed_work(glock_workqueue, &gl->gl_work, 0) == 0)
-				gfs2_glock_put(gl);
+				gfs2_glock_put_nolock(gl);
+			spin_unlock(&gl->gl_spin);
+			clear_bit(GLF_LOCK, &gl->gl_flags);
 			spin_lock(&lru_lock);
 			continue;
 		}
@@ -1738,6 +1765,11 @@ int __init gfs2_glock_init(void)
 	glock_workqueue = create_workqueue("glock_workqueue");
 	if (IS_ERR(glock_workqueue))
 		return PTR_ERR(glock_workqueue);
+	gfs2_delete_workqueue = create_workqueue("delete_workqueue");
+	if (IS_ERR(gfs2_delete_workqueue)) {
+		destroy_workqueue(glock_workqueue);
+		return PTR_ERR(gfs2_delete_workqueue);
+	}
 
 	register_shrinker(&glock_shrinker);
 
@@ -1748,6 +1780,7 @@ void gfs2_glock_exit(void)
 {
 	unregister_shrinker(&glock_shrinker);
 	destroy_workqueue(glock_workqueue);
+	destroy_workqueue(gfs2_delete_workqueue);
 }
 
 static int gfs2_glock_iter_next(struct gfs2_glock_iter *gi)
diff --git a/fs/gfs2/glock.h b/fs/gfs2/glock.h
index a602a28f6f0..c609894ec0d 100644
--- a/fs/gfs2/glock.h
+++ b/fs/gfs2/glock.h
@@ -143,6 +143,7 @@ struct lm_lockops {
 
 #define GLR_TRYFAILED		13
 
+extern struct workqueue_struct *gfs2_delete_workqueue;
 static inline struct gfs2_holder *gfs2_glock_is_locked_by_me(struct gfs2_glock *gl)
 {
 	struct gfs2_holder *gh;
@@ -191,6 +192,8 @@ static inline int gfs2_glock_is_blocking(struct gfs2_glock *gl)
 int gfs2_glock_get(struct gfs2_sbd *sdp,
 		   u64 number, const struct gfs2_glock_operations *glops,
 		   int create, struct gfs2_glock **glp);
+void gfs2_glock_hold(struct gfs2_glock *gl);
+void gfs2_glock_put_nolock(struct gfs2_glock *gl);
 int gfs2_glock_put(struct gfs2_glock *gl);
 void gfs2_holder_init(struct gfs2_glock *gl, unsigned int state, unsigned flags,
 		      struct gfs2_holder *gh);
diff --git a/fs/gfs2/glops.c b/fs/gfs2/glops.c
index d5e4ab155ca..6985eef06c3 100644
--- a/fs/gfs2/glops.c
+++ b/fs/gfs2/glops.c
@@ -323,6 +323,7 @@ static void trans_go_sync(struct gfs2_glock *gl)
 
 	if (gl->gl_state != LM_ST_UNLOCKED &&
 	    test_bit(SDF_JOURNAL_LIVE, &sdp->sd_flags)) {
+		flush_workqueue(gfs2_delete_workqueue);
 		gfs2_meta_syncfs(sdp);
 		gfs2_log_shutdown(sdp);
 	}
@@ -372,6 +373,25 @@ static int trans_go_demote_ok(const struct gfs2_glock *gl)
 	return 0;
 }
 
+/**
+ * iopen_go_callback - schedule the dcache entry for the inode to be deleted
+ * @gl: the glock
+ *
+ * gl_spin lock is held while calling this
+ */
+static void iopen_go_callback(struct gfs2_glock *gl)
+{
+	struct gfs2_inode *ip = (struct gfs2_inode *)gl->gl_object;
+
+	if (gl->gl_demote_state == LM_ST_UNLOCKED &&
+	    gl->gl_state == LM_ST_SHARED &&
+	    ip && test_bit(GIF_USER, &ip->i_flags)) {
+		gfs2_glock_hold(gl);
+		if (queue_work(gfs2_delete_workqueue, &gl->gl_delete) == 0)
+			gfs2_glock_put_nolock(gl);
+	}
+}
+
 const struct gfs2_glock_operations gfs2_meta_glops = {
 	.go_type = LM_TYPE_META,
 };
@@ -406,6 +426,7 @@ const struct gfs2_glock_operations gfs2_trans_glops = {
 
 const struct gfs2_glock_operations gfs2_iopen_glops = {
 	.go_type = LM_TYPE_IOPEN,
+	.go_callback = iopen_go_callback,
 };
 
 const struct gfs2_glock_operations gfs2_flock_glops = {
diff --git a/fs/gfs2/incore.h b/fs/gfs2/incore.h
index 225347fbff3..61801ada36f 100644
--- a/fs/gfs2/incore.h
+++ b/fs/gfs2/incore.h
@@ -159,6 +159,7 @@ struct gfs2_glock_operations {
 	int (*go_lock) (struct gfs2_holder *gh);
 	void (*go_unlock) (struct gfs2_holder *gh);
 	int (*go_dump)(struct seq_file *seq, const struct gfs2_glock *gl);
+	void (*go_callback) (struct gfs2_glock *gl);
 	const int go_type;
 	const unsigned long go_min_hold_time;
 };
@@ -228,6 +229,7 @@ struct gfs2_glock {
 	struct list_head gl_ail_list;
 	atomic_t gl_ail_count;
 	struct delayed_work gl_work;
+	struct work_struct gl_delete;
 };
 
 #define GFS2_MIN_LVB_SIZE 32	/* Min size of LVB that gfs2 supports */
diff --git a/fs/gfs2/super.c b/fs/gfs2/super.c
index 552e321cee5..f522bb01797 100644
--- a/fs/gfs2/super.c
+++ b/fs/gfs2/super.c
@@ -691,6 +691,7 @@ static int gfs2_make_fs_ro(struct gfs2_sbd *sdp)
 	struct gfs2_holder t_gh;
 	int error;
 
+	flush_workqueue(gfs2_delete_workqueue);
 	gfs2_quota_sync(sdp);
 	gfs2_statfs_sync(sdp);
 
-- 
GitLab


From 276e680d192a67d222fcea51af37b056feffb665 Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Thu, 30 Jul 2009 09:40:40 -0400
Subject: [PATCH 0321/1153] Btrfs: preserve commit_root for async caching

The async block group caching code uses the commit_root pointer
to get a stable version of the extent allocation tree for scanning.
This copy of the tree root isn't going to change and it significantly
reduces the complexity of the scanning code.

During a commit, we have a loop where we update the extent allocation
tree root.  We need to loop because updating the root pointer in
the tree of tree roots may allocate blocks which may change the
extent allocation tree.

Right now the commit_root pointer is changed inside this loop.  It
is more correct to change the commit_root pointer only after all the
looping is done.

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/ctree.h       |  4 +---
 fs/btrfs/disk-io.c     |  2 +-
 fs/btrfs/extent-tree.c |  6 +++---
 fs/btrfs/transaction.c | 12 +++++++++---
 4 files changed, 14 insertions(+), 10 deletions(-)

diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h
index 17ad92c29cf..38eeb6c49c8 100644
--- a/fs/btrfs/ctree.h
+++ b/fs/btrfs/ctree.h
@@ -827,6 +827,7 @@ struct btrfs_fs_info {
 	struct mutex drop_mutex;
 	struct mutex volume_mutex;
 	struct mutex tree_reloc_mutex;
+	struct rw_semaphore extent_commit_sem;
 
 	/*
 	 * this protects the ordered operations list only while we are
@@ -961,9 +962,6 @@ struct btrfs_root {
 	/* the node lock is held while changing the node pointer */
 	spinlock_t node_lock;
 
-	/* taken when updating the commit root */
-	struct rw_semaphore commit_root_sem;
-
 	struct extent_buffer *commit_root;
 	struct btrfs_root *log_root;
 	struct btrfs_root *reloc_root;
diff --git a/fs/btrfs/disk-io.c b/fs/btrfs/disk-io.c
index 3a9b8875988..3cf4cfa575c 100644
--- a/fs/btrfs/disk-io.c
+++ b/fs/btrfs/disk-io.c
@@ -907,7 +907,6 @@ static int __setup_root(u32 nodesize, u32 leafsize, u32 sectorsize,
 	spin_lock_init(&root->inode_lock);
 	mutex_init(&root->objectid_mutex);
 	mutex_init(&root->log_mutex);
-	init_rwsem(&root->commit_root_sem);
 	init_waitqueue_head(&root->log_writer_wait);
 	init_waitqueue_head(&root->log_commit_wait[0]);
 	init_waitqueue_head(&root->log_commit_wait[1]);
@@ -1624,6 +1623,7 @@ struct btrfs_root *open_ctree(struct super_block *sb,
 	mutex_init(&fs_info->cleaner_mutex);
 	mutex_init(&fs_info->volume_mutex);
 	mutex_init(&fs_info->tree_reloc_mutex);
+	init_rwsem(&fs_info->extent_commit_sem);
 
 	btrfs_init_free_cluster(&fs_info->meta_alloc_cluster);
 	btrfs_init_free_cluster(&fs_info->data_alloc_cluster);
diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index fadf69a2764..2fe21fa7491 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -267,7 +267,7 @@ static int caching_kthread(void *data)
 	last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET);
 again:
 	/* need to make sure the commit_root doesn't disappear */
-	down_read(&fs_info->extent_root->commit_root_sem);
+	down_read(&fs_info->extent_commit_sem);
 
 	/*
 	 * We don't want to deadlock with somebody trying to allocate a new
@@ -304,7 +304,7 @@ again:
 
 			if (need_resched()) {
 				btrfs_release_path(fs_info->extent_root, path);
-				up_read(&fs_info->extent_root->commit_root_sem);
+				up_read(&fs_info->extent_commit_sem);
 				cond_resched();
 				goto again;
 			}
@@ -345,7 +345,7 @@ next:
 
 err:
 	btrfs_free_path(path);
-	up_read(&fs_info->extent_root->commit_root_sem);
+	up_read(&fs_info->extent_commit_sem);
 	atomic_dec(&block_group->space_info->caching_threads);
 	wake_up(&block_group->caching_q);
 
diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c
index e51d2bc532f..de48e4ec808 100644
--- a/fs/btrfs/transaction.c
+++ b/fs/btrfs/transaction.c
@@ -42,10 +42,8 @@ static noinline void put_transaction(struct btrfs_transaction *transaction)
 
 static noinline void switch_commit_root(struct btrfs_root *root)
 {
-	down_write(&root->commit_root_sem);
 	free_extent_buffer(root->commit_root);
 	root->commit_root = btrfs_root_node(root);
-	up_write(&root->commit_root_sem);
 }
 
 /*
@@ -466,7 +464,10 @@ static int update_cowonly_root(struct btrfs_trans_handle *trans,
 		ret = btrfs_write_dirty_block_groups(trans, root);
 		BUG_ON(ret);
 	}
-	switch_commit_root(root);
+
+	if (root != root->fs_info->extent_root)
+		switch_commit_root(root);
+
 	return 0;
 }
 
@@ -499,6 +500,11 @@ static noinline int commit_cowonly_roots(struct btrfs_trans_handle *trans,
 
 		update_cowonly_root(trans, root);
 	}
+
+	down_write(&fs_info->extent_commit_sem);
+	switch_commit_root(fs_info->extent_root);
+	up_write(&fs_info->extent_commit_sem);
+
 	return 0;
 }
 
-- 
GitLab


From dfb3cf00e402686f671db697adbd8b9f4c219268 Mon Sep 17 00:00:00 2001
From: Swen Schillig <swen@vnet.ibm.com>
Date: Mon, 13 Jul 2009 15:06:02 +0200
Subject: [PATCH 0322/1153] [SCSI] zfcp: Fix invalid command order

We should not modify the port status after triggering an ERP action
for the port. It is not guaranteed which status is finally active
when the ERP action is performed. This can lead to situations which
are unwanted and hard to debug in case of a failure.

Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_fsf.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c
index c57658f3d34..bbb7ef0b052 100644
--- a/drivers/s390/scsi/zfcp_fsf.c
+++ b/drivers/s390/scsi/zfcp_fsf.c
@@ -1731,15 +1731,16 @@ static void zfcp_fsf_close_physical_port_handler(struct zfcp_fsf_req *req)
 		zfcp_fsf_access_denied_port(req, port);
 		break;
 	case FSF_PORT_BOXED:
-		zfcp_erp_port_boxed(port, "fscpph2", req);
-		req->status |= ZFCP_STATUS_FSFREQ_ERROR |
-			       ZFCP_STATUS_FSFREQ_RETRY;
 		/* can't use generic zfcp_erp_modify_port_status because
 		 * ZFCP_STATUS_COMMON_OPEN must not be reset for the port */
 		atomic_clear_mask(ZFCP_STATUS_PORT_PHYS_OPEN, &port->status);
 		list_for_each_entry(unit, &port->unit_list_head, list)
 			atomic_clear_mask(ZFCP_STATUS_COMMON_OPEN,
 					  &unit->status);
+		zfcp_erp_port_boxed(port, "fscpph2", req);
+		req->status |= ZFCP_STATUS_FSFREQ_ERROR |
+			       ZFCP_STATUS_FSFREQ_RETRY;
+
 		break;
 	case FSF_ADAPTER_STATUS_AVAILABLE:
 		switch (header->fsf_status_qual.word[0]) {
-- 
GitLab


From acf7b86150701de105aa8307b4b3f9dc533c45bb Mon Sep 17 00:00:00 2001
From: Christof Schmitt <christof.schmitt@de.ibm.com>
Date: Mon, 13 Jul 2009 15:06:03 +0200
Subject: [PATCH 0323/1153] [SCSI] zfcp: Acquire qdio_stat_lock when reading
 the queue utilization

req_q_util is not atomic, so the qdio_stat_lock must be held when
reading this variable.

Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_sysfs.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/s390/scsi/zfcp_sysfs.c b/drivers/s390/scsi/zfcp_sysfs.c
index 3e51e64d110..0fe5cce818c 100644
--- a/drivers/s390/scsi/zfcp_sysfs.c
+++ b/drivers/s390/scsi/zfcp_sysfs.c
@@ -494,9 +494,14 @@ static ssize_t zfcp_sysfs_adapter_q_full_show(struct device *dev,
 	struct Scsi_Host *scsi_host = class_to_shost(dev);
 	struct zfcp_adapter *adapter =
 		(struct zfcp_adapter *) scsi_host->hostdata[0];
+	u64 util;
+
+	spin_lock_bh(&adapter->qdio_stat_lock);
+	util = adapter->req_q_util;
+	spin_unlock_bh(&adapter->qdio_stat_lock);
 
 	return sprintf(buf, "%d %llu\n", atomic_read(&adapter->qdio_outb_full),
-		       (unsigned long long)adapter->req_q_util);
+		       (unsigned long long)util);
 }
 static DEVICE_ATTR(queue_full, S_IRUGO, zfcp_sysfs_adapter_q_full_show, NULL);
 
-- 
GitLab


From 1e9b16430ff4fd09408a74342d6b8338228e2f70 Mon Sep 17 00:00:00 2001
From: Christof Schmitt <christof.schmitt@de.ibm.com>
Date: Mon, 13 Jul 2009 15:06:04 +0200
Subject: [PATCH 0324/1153] [SCSI] zfcp: Return -ENOMEM for allocation failures
 in zfcp_fsf

When a fsf_req or a qtcb cannot be allocated return -ENOMEM instead of
-EIO.

Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_fsf.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c
index bbb7ef0b052..c4eb62b32a3 100644
--- a/drivers/s390/scsi/zfcp_fsf.c
+++ b/drivers/s390/scsi/zfcp_fsf.c
@@ -722,7 +722,7 @@ static struct zfcp_fsf_req *zfcp_fsf_req_create(struct zfcp_adapter *adapter,
 		req = zfcp_fsf_alloc_qtcb(pool);
 
 	if (unlikely(!req))
-		return ERR_PTR(-EIO);
+		return ERR_PTR(-ENOMEM);
 
 	if (adapter->req_no == 0)
 		adapter->req_no++;
-- 
GitLab


From 688a1820bde27749f22b18b94ef1c9bc179b1b29 Mon Sep 17 00:00:00 2001
From: Christof Schmitt <christof.schmitt@de.ibm.com>
Date: Mon, 13 Jul 2009 15:06:05 +0200
Subject: [PATCH 0325/1153] [SCSI] zfcp: Use correct flags for zfcp_erp_notify

zfcp_erp_notify uses the ZFCP_ERP_STATUS_* flags, so it is
ZFCP_STATUS_ERP_LOWMEM instead of ZFCP_ERP_NOMEM. Signalling
ZFCP_ERP_FAILED is not necessary, the missing d_id will show that the
nameserver did not return the d_id.

Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_erp.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c
index 8030e25152f..e7d7ef55e37 100644
--- a/drivers/s390/scsi/zfcp_erp.c
+++ b/drivers/s390/scsi/zfcp_erp.c
@@ -854,10 +854,10 @@ void zfcp_erp_port_strategy_open_lookup(struct work_struct *work)
 
 	retval = zfcp_fc_ns_gid_pn(&port->erp_action);
 	if (retval == -ENOMEM)
-		zfcp_erp_notify(&port->erp_action, ZFCP_ERP_NOMEM);
+		zfcp_erp_notify(&port->erp_action, ZFCP_STATUS_ERP_LOWMEM);
 	port->erp_action.step = ZFCP_ERP_STEP_NAMESERVER_LOOKUP;
 	if (retval)
-		zfcp_erp_notify(&port->erp_action, ZFCP_ERP_FAILED);
+		zfcp_erp_notify(&port->erp_action, 0);
 	zfcp_port_put(port);
 }
 
-- 
GitLab


From 426f6059b0eb66cec139f4b9066168ab72b85774 Mon Sep 17 00:00:00 2001
From: Christof Schmitt <christof.schmitt@de.ibm.com>
Date: Mon, 13 Jul 2009 15:06:06 +0200
Subject: [PATCH 0326/1153] [SCSI] zfcp: Use unchained mode for small ct and
 els requests

The ELS ADISC and the GID_PN requests sent from zfcp fit into
unchained FSF requests. Change the FSF allocation logic to use
unchained requests whenever possible where everything fits in one
SBAL. This avoids acquiring more SBALs than necessary, especially
during zfcp recovery when things might be stalled.

Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_fsf.c | 33 +++++++++++++++++++++++++--------
 1 file changed, 25 insertions(+), 8 deletions(-)

diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c
index c4eb62b32a3..bec912547fb 100644
--- a/drivers/s390/scsi/zfcp_fsf.c
+++ b/drivers/s390/scsi/zfcp_fsf.c
@@ -1010,6 +1010,23 @@ skip_fsfstatus:
 		send_ct->handler(send_ct->handler_data);
 }
 
+static void zfcp_fsf_setup_ct_els_unchained(struct qdio_buffer_element *sbale,
+					    struct scatterlist *sg_req,
+					    struct scatterlist *sg_resp)
+{
+	sbale[0].flags |= SBAL_FLAGS0_TYPE_WRITE_READ;
+	sbale[2].addr   = sg_virt(sg_req);
+	sbale[2].length = sg_req->length;
+	sbale[3].addr   = sg_virt(sg_resp);
+	sbale[3].length = sg_resp->length;
+	sbale[3].flags |= SBAL_FLAGS_LAST_ENTRY;
+}
+
+static int zfcp_fsf_one_sbal(struct scatterlist *sg)
+{
+	return sg_is_last(sg) && sg->length <= PAGE_SIZE;
+}
+
 static int zfcp_fsf_setup_ct_els_sbals(struct zfcp_fsf_req *req,
 				       struct scatterlist *sg_req,
 				       struct scatterlist *sg_resp,
@@ -1020,16 +1037,16 @@ static int zfcp_fsf_setup_ct_els_sbals(struct zfcp_fsf_req *req,
 	int bytes;
 
 	if (!(feat & FSF_FEATURE_ELS_CT_CHAINED_SBALS)) {
-		if (sg_req->length > PAGE_SIZE || sg_resp->length > PAGE_SIZE ||
-		    !sg_is_last(sg_req) || !sg_is_last(sg_resp))
+		if (!zfcp_fsf_one_sbal(sg_req) || !zfcp_fsf_one_sbal(sg_resp))
 			return -EOPNOTSUPP;
 
-		sbale[0].flags |= SBAL_FLAGS0_TYPE_WRITE_READ;
-		sbale[2].addr   = sg_virt(sg_req);
-		sbale[2].length = sg_req->length;
-		sbale[3].addr   = sg_virt(sg_resp);
-		sbale[3].length = sg_resp->length;
-		sbale[3].flags |= SBAL_FLAGS_LAST_ENTRY;
+		zfcp_fsf_setup_ct_els_unchained(sbale, sg_req, sg_resp);
+		return 0;
+	}
+
+	/* use single, unchained SBAL if it can hold the request */
+	if (zfcp_fsf_one_sbal(sg_req) && zfcp_fsf_one_sbal(sg_resp)) {
+		zfcp_fsf_setup_ct_els_unchained(sbale, sg_req, sg_resp);
 		return 0;
 	}
 
-- 
GitLab


From 9072df4dc6e8fd569d583815edb0198af4b688b8 Mon Sep 17 00:00:00 2001
From: Christof Schmitt <christof.schmitt@de.ibm.com>
Date: Mon, 13 Jul 2009 15:06:07 +0200
Subject: [PATCH 0327/1153] [SCSI] zfcp: Use -EIO for SBAL allocation failures

-ENOMEM is for memory allocation problems, -EIO for queue/SBAL
allocation problems.

Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_fsf.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c
index bec912547fb..0c24695a53c 100644
--- a/drivers/s390/scsi/zfcp_fsf.c
+++ b/drivers/s390/scsi/zfcp_fsf.c
@@ -1053,14 +1053,14 @@ static int zfcp_fsf_setup_ct_els_sbals(struct zfcp_fsf_req *req,
 	bytes = zfcp_qdio_sbals_from_sg(req, SBAL_FLAGS0_TYPE_WRITE_READ,
 					sg_req, max_sbals);
 	if (bytes <= 0)
-		return -ENOMEM;
+		return -EIO;
 	req->qtcb->bottom.support.req_buf_length = bytes;
 	req->sbale_curr = ZFCP_LAST_SBALE_PER_SBAL;
 
 	bytes = zfcp_qdio_sbals_from_sg(req, SBAL_FLAGS0_TYPE_WRITE_READ,
 					sg_resp, max_sbals);
 	if (bytes <= 0)
-		return -ENOMEM;
+		return -EIO;
 	req->qtcb->bottom.support.resp_buf_length = bytes;
 
 	return 0;
@@ -2559,7 +2559,6 @@ struct zfcp_fsf_req *zfcp_fsf_control_file(struct zfcp_adapter *adapter,
 	bytes = zfcp_qdio_sbals_from_sg(req, direction, fsf_cfdc->sg,
 					FSF_MAX_SBALS_PER_REQ);
 	if (bytes != ZFCP_CFDC_MAX_SIZE) {
-		retval = -ENOMEM;
 		zfcp_fsf_req_free(req);
 		goto out;
 	}
-- 
GitLab


From ddb3e0c111fed0a8bf74884dc918274acec2b618 Mon Sep 17 00:00:00 2001
From: Christof Schmitt <christof.schmitt@de.ibm.com>
Date: Mon, 13 Jul 2009 15:06:08 +0200
Subject: [PATCH 0328/1153] [SCSI] zfcp: Fix logic for physical port close

After closing the port, we want it to be "not open" to consider the
action to be successful.

Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_erp.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c
index e7d7ef55e37..0a7c6aef532 100644
--- a/drivers/s390/scsi/zfcp_erp.c
+++ b/drivers/s390/scsi/zfcp_erp.c
@@ -801,7 +801,7 @@ static int zfcp_erp_port_forced_strategy(struct zfcp_erp_action *erp_action)
 			return ZFCP_ERP_FAILED;
 
 	case ZFCP_ERP_STEP_PHYS_PORT_CLOSING:
-		if (status & ZFCP_STATUS_PORT_PHYS_OPEN)
+		if (!(status & ZFCP_STATUS_PORT_PHYS_OPEN))
 			return ZFCP_ERP_SUCCEEDED;
 	}
 	return ZFCP_ERP_FAILED;
-- 
GitLab


From 85600f7f8370fe5b4be0debd8b401de7986b52ae Mon Sep 17 00:00:00 2001
From: Christof Schmitt <christof.schmitt@de.ibm.com>
Date: Mon, 13 Jul 2009 15:06:09 +0200
Subject: [PATCH 0329/1153] [SCSI] zfcp: Fix erp escalation procedure

If an action fails, retry it until the erp count exceeds the
threshold. If there is something fundamentally wrong, the FSF layer
will trigger a more appropriate action depending on the FSF status
codes.

The followup for successful actions is a different followup than
retrying failed actions, so split the code two functions to make this
clear.

Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_erp.c | 50 +++++++++++++++++-------------------
 1 file changed, 24 insertions(+), 26 deletions(-)

diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c
index 0a7c6aef532..b5562f95265 100644
--- a/drivers/s390/scsi/zfcp_erp.c
+++ b/drivers/s390/scsi/zfcp_erp.c
@@ -553,40 +553,35 @@ static void _zfcp_erp_unit_reopen_all(struct zfcp_port *port, int clear,
 		_zfcp_erp_unit_reopen(unit, clear, id, ref);
 }
 
-static void zfcp_erp_strategy_followup_actions(struct zfcp_erp_action *act)
+static void zfcp_erp_strategy_followup_failed(struct zfcp_erp_action *act)
 {
-	struct zfcp_adapter *adapter = act->adapter;
-	struct zfcp_port *port = act->port;
-	struct zfcp_unit *unit = act->unit;
-	u32 status = act->status;
-
-	/* initiate follow-up actions depending on success of finished action */
 	switch (act->action) {
-
 	case ZFCP_ERP_ACTION_REOPEN_ADAPTER:
-		if (status == ZFCP_ERP_SUCCEEDED)
-			_zfcp_erp_port_reopen_all(adapter, 0, "ersfa_1", NULL);
-		else
-			_zfcp_erp_adapter_reopen(adapter, 0, "ersfa_2", NULL);
+		_zfcp_erp_adapter_reopen(act->adapter, 0, "ersff_1", NULL);
 		break;
-
 	case ZFCP_ERP_ACTION_REOPEN_PORT_FORCED:
-		if (status == ZFCP_ERP_SUCCEEDED)
-			_zfcp_erp_port_reopen(port, 0, "ersfa_3", NULL);
-		else
-			_zfcp_erp_adapter_reopen(adapter, 0, "ersfa_4", NULL);
+		_zfcp_erp_port_forced_reopen(act->port, 0, "ersff_2", NULL);
 		break;
-
 	case ZFCP_ERP_ACTION_REOPEN_PORT:
-		if (status == ZFCP_ERP_SUCCEEDED)
-			_zfcp_erp_unit_reopen_all(port, 0, "ersfa_5", NULL);
-		else
-			_zfcp_erp_port_forced_reopen(port, 0, "ersfa_6", NULL);
+		_zfcp_erp_port_reopen(act->port, 0, "ersff_3", NULL);
 		break;
-
 	case ZFCP_ERP_ACTION_REOPEN_UNIT:
-		if (status != ZFCP_ERP_SUCCEEDED)
-			_zfcp_erp_port_reopen(unit->port, 0, "ersfa_7", NULL);
+		_zfcp_erp_unit_reopen(act->unit, 0, "ersff_4", NULL);
+		break;
+	}
+}
+
+static void zfcp_erp_strategy_followup_success(struct zfcp_erp_action *act)
+{
+	switch (act->action) {
+	case ZFCP_ERP_ACTION_REOPEN_ADAPTER:
+		_zfcp_erp_port_reopen_all(act->adapter, 0, "ersfs_1", NULL);
+		break;
+	case ZFCP_ERP_ACTION_REOPEN_PORT_FORCED:
+		_zfcp_erp_port_reopen(act->port, 0, "ersfs_2", NULL);
+		break;
+	case ZFCP_ERP_ACTION_REOPEN_PORT:
+		_zfcp_erp_unit_reopen_all(act->port, 0, "ersfs_3", NULL);
 		break;
 	}
 }
@@ -1289,7 +1284,10 @@ static int zfcp_erp_strategy(struct zfcp_erp_action *erp_action)
 	retval = zfcp_erp_strategy_statechange(erp_action, retval);
 	if (retval == ZFCP_ERP_EXIT)
 		goto unlock;
-	zfcp_erp_strategy_followup_actions(erp_action);
+	if (retval == ZFCP_ERP_SUCCEEDED)
+		zfcp_erp_strategy_followup_success(erp_action);
+	if (retval == ZFCP_ERP_FAILED)
+		zfcp_erp_strategy_followup_failed(erp_action);
 
  unlock:
 	write_unlock(&adapter->erp_lock);
-- 
GitLab


From cbf1ed0264da104573458aedc220ebfcd02567f6 Mon Sep 17 00:00:00 2001
From: Christof Schmitt <christof.schmitt@de.ibm.com>
Date: Mon, 13 Jul 2009 15:06:10 +0200
Subject: [PATCH 0330/1153] [SCSI] zfcp: Recover from stalled outbound queue

Depending on interruptions on some storage systems, the complete
channel can stall which looks like an outbound queue stall to Linux.
When trying to acquire a free SBAL for a non-SCSI command, zfcp waits
for 5 seconds for a free slot to appear. This is the right place to
detect a queue stall: If the wait times out, we assume a stalled queue
and try to recover this.

The overall strategy should be to trigger the erp from specific
events, and not try an overall escalation from one failed port to a
full-blown queue recovery. If we manage to send a command, the status
codes for this command or a timeout will trigger the right follow-on
actions.

Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_fsf.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c
index 0c24695a53c..b7e48844056 100644
--- a/drivers/s390/scsi/zfcp_fsf.c
+++ b/drivers/s390/scsi/zfcp_fsf.c
@@ -670,8 +670,11 @@ static int zfcp_fsf_req_sbal_get(struct zfcp_adapter *adapter)
 			       zfcp_fsf_sbal_check(adapter), 5 * HZ);
 	if (ret > 0)
 		return 0;
-	if (!ret)
+	if (!ret) {
 		atomic_inc(&adapter->qdio_outb_full);
+		/* assume hanging outbound queue, try queue recovery */
+		zfcp_erp_adapter_reopen(adapter, 0, "fsrsg_1", NULL);
+	}
 
 	spin_lock_bh(&adapter->req_q_lock);
 	return -EIO;
-- 
GitLab


From 379d6bf6573ee6541a38bbe9140c1f0b94e3feae Mon Sep 17 00:00:00 2001
From: Christof Schmitt <christof.schmitt@de.ibm.com>
Date: Mon, 13 Jul 2009 15:06:11 +0200
Subject: [PATCH 0331/1153] [SCSI] zfcp: Add port only once to FC transport
 class

When calling fc_remote_port_add make sure to not call it again before
fc_remote_port_delete has been called. In other words, ensure to
create a new fc_rport, then delete it, then create a new one again.

Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_scsi.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/s390/scsi/zfcp_scsi.c b/drivers/s390/scsi/zfcp_scsi.c
index 967ede73f4c..ba32709921a 100644
--- a/drivers/s390/scsi/zfcp_scsi.c
+++ b/drivers/s390/scsi/zfcp_scsi.c
@@ -534,6 +534,9 @@ static void zfcp_scsi_rport_register(struct zfcp_port *port)
 	struct fc_rport_identifiers ids;
 	struct fc_rport *rport;
 
+	if (port->rport)
+		return;
+
 	ids.node_name = port->wwnn;
 	ids.port_name = port->wwpn;
 	ids.port_id = port->d_id;
@@ -557,8 +560,10 @@ static void zfcp_scsi_rport_block(struct zfcp_port *port)
 {
 	struct fc_rport *rport = port->rport;
 
-	if (rport)
+	if (rport) {
 		fc_remote_port_delete(rport);
+		port->rport = NULL;
+	}
 }
 
 void zfcp_scsi_schedule_rport_register(struct zfcp_port *port)
-- 
GitLab


From 17a093ef018481ee1760da19568bad3c11da395d Mon Sep 17 00:00:00 2001
From: Swen Schillig <swen@vnet.ibm.com>
Date: Mon, 13 Jul 2009 15:06:12 +0200
Subject: [PATCH 0332/1153] [SCSI] zfcp: avoid double notify in lowmem scenario

In a LOWMEM condition an ERP notification would have been sent twice
causing an unpredictable behaviour of the ERP.

Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_erp.c | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c
index b5562f95265..c75d6f35cb5 100644
--- a/drivers/s390/scsi/zfcp_erp.c
+++ b/drivers/s390/scsi/zfcp_erp.c
@@ -848,11 +848,17 @@ void zfcp_erp_port_strategy_open_lookup(struct work_struct *work)
 					      gid_pn_work);
 
 	retval = zfcp_fc_ns_gid_pn(&port->erp_action);
-	if (retval == -ENOMEM)
+	if (!retval) {
+		port->erp_action.step = ZFCP_ERP_STEP_NAMESERVER_LOOKUP;
+		goto out;
+	}
+	if (retval == -ENOMEM) {
 		zfcp_erp_notify(&port->erp_action, ZFCP_STATUS_ERP_LOWMEM);
-	port->erp_action.step = ZFCP_ERP_STEP_NAMESERVER_LOOKUP;
-	if (retval)
-		zfcp_erp_notify(&port->erp_action, 0);
+		goto out;
+	}
+	/* all other error condtions */
+	zfcp_erp_notify(&port->erp_action, 0);
+out:
 	zfcp_port_put(port);
 }
 
-- 
GitLab


From 27f492ccec94b6acd8440c83bfe0515ce4db0af0 Mon Sep 17 00:00:00 2001
From: Swen Schillig <swen@vnet.ibm.com>
Date: Mon, 13 Jul 2009 15:06:13 +0200
Subject: [PATCH 0333/1153] [SCSI] zfcp: Fix wka port processing

Under certain conditions it is possible that a WKA port ist not opened
within the expected timeframe of half a second. In this situation
the WKA port remains in the state OPENING preventing any succeding
request to open the port. This led to unrecoverable remote ports.
Fixing this by always setting an appropriate WKA port status before
leaving the function and removing the timeout value here since it's
not needed here because the general timeout processing would deal
with it if required.

Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_fc.c  | 8 +++-----
 drivers/s390/scsi/zfcp_fsf.c | 4 ++--
 2 files changed, 5 insertions(+), 7 deletions(-)

diff --git a/drivers/s390/scsi/zfcp_fc.c b/drivers/s390/scsi/zfcp_fc.c
index 2f0705d76b7..47daebfa7e5 100644
--- a/drivers/s390/scsi/zfcp_fc.c
+++ b/drivers/s390/scsi/zfcp_fc.c
@@ -79,11 +79,9 @@ static int zfcp_wka_port_get(struct zfcp_wka_port *wka_port)
 
 	mutex_unlock(&wka_port->mutex);
 
-	wait_event_timeout(
-		wka_port->completion_wq,
-		wka_port->status == ZFCP_WKA_PORT_ONLINE ||
-		wka_port->status == ZFCP_WKA_PORT_OFFLINE,
-		HZ >> 1);
+	wait_event(wka_port->completion_wq,
+		   wka_port->status == ZFCP_WKA_PORT_ONLINE ||
+		   wka_port->status == ZFCP_WKA_PORT_OFFLINE);
 
 	if (wka_port->status == ZFCP_WKA_PORT_ONLINE) {
 		atomic_inc(&wka_port->refcount);
diff --git a/drivers/s390/scsi/zfcp_fsf.c b/drivers/s390/scsi/zfcp_fsf.c
index b7e48844056..47795fbf081 100644
--- a/drivers/s390/scsi/zfcp_fsf.c
+++ b/drivers/s390/scsi/zfcp_fsf.c
@@ -1627,10 +1627,10 @@ static void zfcp_fsf_open_wka_port_handler(struct zfcp_fsf_req *req)
 	case FSF_ACCESS_DENIED:
 		wka_port->status = ZFCP_WKA_PORT_OFFLINE;
 		break;
-	case FSF_PORT_ALREADY_OPEN:
-		break;
 	case FSF_GOOD:
 		wka_port->handle = header->port_handle;
+		/* fall through */
+	case FSF_PORT_ALREADY_OPEN:
 		wka_port->status = ZFCP_WKA_PORT_ONLINE;
 	}
 out:
-- 
GitLab


From a11a52be115889a5d1f738ed2e154807bceed4ee Mon Sep 17 00:00:00 2001
From: Christof Schmitt <christof.schmitt@de.ibm.com>
Date: Mon, 13 Jul 2009 15:06:14 +0200
Subject: [PATCH 0334/1153] [SCSI] zfcp: Fix tracing of request id for abort
 requests

The trace record for SCSI abort requests has a field for the request
id of the request to be aborted. Put the real request id instead of
zero.

Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/s390/scsi/zfcp_scsi.c | 18 ++++++++++--------
 1 file changed, 10 insertions(+), 8 deletions(-)

diff --git a/drivers/s390/scsi/zfcp_scsi.c b/drivers/s390/scsi/zfcp_scsi.c
index ba32709921a..6925a178468 100644
--- a/drivers/s390/scsi/zfcp_scsi.c
+++ b/drivers/s390/scsi/zfcp_scsi.c
@@ -167,20 +167,21 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt)
 	struct zfcp_unit *unit = scpnt->device->hostdata;
 	struct zfcp_fsf_req *old_req, *abrt_req;
 	unsigned long flags;
-	unsigned long old_req_id = (unsigned long) scpnt->host_scribble;
+	unsigned long old_reqid = (unsigned long) scpnt->host_scribble;
 	int retval = SUCCESS;
 	int retry = 3;
+	char *dbf_tag;
 
 	/* avoid race condition between late normal completion and abort */
 	write_lock_irqsave(&adapter->abort_lock, flags);
 
 	spin_lock(&adapter->req_list_lock);
-	old_req = zfcp_reqlist_find(adapter, old_req_id);
+	old_req = zfcp_reqlist_find(adapter, old_reqid);
 	spin_unlock(&adapter->req_list_lock);
 	if (!old_req) {
 		write_unlock_irqrestore(&adapter->abort_lock, flags);
 		zfcp_scsi_dbf_event_abort("lte1", adapter, scpnt, NULL,
-					  old_req_id);
+					  old_reqid);
 		return FAILED; /* completion could be in progress */
 	}
 	old_req->data = NULL;
@@ -189,7 +190,7 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt)
 	write_unlock_irqrestore(&adapter->abort_lock, flags);
 
 	while (retry--) {
-		abrt_req = zfcp_fsf_abort_fcp_command(old_req_id, unit);
+		abrt_req = zfcp_fsf_abort_fcp_command(old_reqid, unit);
 		if (abrt_req)
 			break;
 
@@ -197,7 +198,7 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt)
 		if (!(atomic_read(&adapter->status) &
 		      ZFCP_STATUS_COMMON_RUNNING)) {
 			zfcp_scsi_dbf_event_abort("nres", adapter, scpnt, NULL,
-						  old_req_id);
+						  old_reqid);
 			return SUCCESS;
 		}
 	}
@@ -208,13 +209,14 @@ static int zfcp_scsi_eh_abort_handler(struct scsi_cmnd *scpnt)
 		   abrt_req->status & ZFCP_STATUS_FSFREQ_COMPLETED);
 
 	if (abrt_req->status & ZFCP_STATUS_FSFREQ_ABORTSUCCEEDED)
-		zfcp_scsi_dbf_event_abort("okay", adapter, scpnt, abrt_req, 0);
+		dbf_tag = "okay";
 	else if (abrt_req->status & ZFCP_STATUS_FSFREQ_ABORTNOTNEEDED)
-		zfcp_scsi_dbf_event_abort("lte2", adapter, scpnt, abrt_req, 0);
+		dbf_tag = "lte2";
 	else {
-		zfcp_scsi_dbf_event_abort("fail", adapter, scpnt, abrt_req, 0);
+		dbf_tag = "fail";
 		retval = FAILED;
 	}
+	zfcp_scsi_dbf_event_abort(dbf_tag, adapter, scpnt, abrt_req, old_reqid);
 	zfcp_fsf_req_free(abrt_req);
 	return retval;
 }
-- 
GitLab


From 6187c242089d334102be76427a5a020240e6c19a Mon Sep 17 00:00:00 2001
From: Mike Christie <michaelc@cs.wisc.edu>
Date: Wed, 15 Jul 2009 15:02:57 -0500
Subject: [PATCH 0335/1153] [SCSI] libiscsi: disable bh in and abort handler.

The session lock can be held in the scsi eh thread or the completion
paths run from the net softirq. This disables bhs in iscsi_eh_abort when
taking the session lock.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/scsi/libiscsi.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/libiscsi.c b/drivers/scsi/libiscsi.c
index 716cc344c5d..a751f6230c2 100644
--- a/drivers/scsi/libiscsi.c
+++ b/drivers/scsi/libiscsi.c
@@ -1974,10 +1974,10 @@ int iscsi_eh_abort(struct scsi_cmnd *sc)
 		 * good and have never sent us a successful tmf response
 		 * then sent more data for the cmd.
 		 */
-		spin_lock(&session->lock);
+		spin_lock_bh(&session->lock);
 		fail_scsi_task(task, DID_ABORT);
 		conn->tmf_state = TMF_INITIAL;
-		spin_unlock(&session->lock);
+		spin_unlock_bh(&session->lock);
 		iscsi_start_tx(conn);
 		goto success_unlocked;
 	case TMF_TIMEDOUT:
-- 
GitLab


From 94bced3c1b371014cbd187f2df5539b13a0e3b90 Mon Sep 17 00:00:00 2001
From: Karen Higgins <karen.higgins@qlogic.com>
Date: Wed, 15 Jul 2009 15:02:58 -0500
Subject: [PATCH 0336/1153] [SCSI] qla4xxx: Correct Extended Sense Data Errors

Fixed sense data errors occurring above the first 32 bytes,
as required by some third party applications.  Sense data
in the first 32 bytes has always been correct.

Patch updated to use srb data variables instead of scsi command
scratchpad data area, as scratchpad area is already used.

Also, corrected debug print alignment bug in dump_buffer routine.
Changed KERN_DEBUG to KERN_INFO in printk statements in this routine.

Changed version number to 5.01.00-k9

Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[michaelc: fixed checkpath.pl errors]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/scsi/qla4xxx/ql4_dbg.c     |  15 ++-
 drivers/scsi/qla4xxx/ql4_def.h     |   7 ++
 drivers/scsi/qla4xxx/ql4_fw.h      |   7 ++
 drivers/scsi/qla4xxx/ql4_isr.c     | 145 ++++++++++++++++++++---------
 drivers/scsi/qla4xxx/ql4_version.h |   2 +-
 5 files changed, 122 insertions(+), 54 deletions(-)

diff --git a/drivers/scsi/qla4xxx/ql4_dbg.c b/drivers/scsi/qla4xxx/ql4_dbg.c
index fcc184cd066..cbceb0ebabf 100644
--- a/drivers/scsi/qla4xxx/ql4_dbg.c
+++ b/drivers/scsi/qla4xxx/ql4_dbg.c
@@ -15,19 +15,18 @@ void qla4xxx_dump_buffer(void *b, uint32_t size)
 	uint32_t cnt;
 	uint8_t *c = b;
 
-	printk(" 0   1	 2   3	 4   5	 6   7	 8   9	Ah  Bh	Ch  Dh	Eh  "
+	printk(" 0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  "
 	       "Fh\n");
 	printk("------------------------------------------------------------"
 	       "--\n");
-	for (cnt = 0; cnt < size; cnt++, c++) {
-		printk(KERN_DEBUG "%02x", *c);
-		if (!(cnt % 16))
-			printk(KERN_DEBUG "\n");
+	for (cnt = 0; cnt < size; c++) {
+		printk(KERN_INFO "%02x", *c);
+		if (!(++cnt % 16))
+			printk(KERN_INFO "\n");
 
 		else
-			printk(KERN_DEBUG "  ");
+			printk(KERN_INFO "  ");
 	}
-	if (cnt % 16)
-		printk(KERN_DEBUG "\n");
+	printk(KERN_INFO "\n");
 }
 
diff --git a/drivers/scsi/qla4xxx/ql4_def.h b/drivers/scsi/qla4xxx/ql4_def.h
index b586f27c3bd..963e8553d21 100644
--- a/drivers/scsi/qla4xxx/ql4_def.h
+++ b/drivers/scsi/qla4xxx/ql4_def.h
@@ -184,6 +184,11 @@ struct srb {
 	uint16_t cc_stat;
 	u_long r_start;		/* Time we recieve a cmd from OS */
 	u_long u_start;		/* Time when we handed the cmd to F/W */
+
+	/* Used for extended sense / status continuation */
+	uint8_t *req_sense_ptr;
+	uint16_t req_sense_len;
+	uint16_t reserved2;
 };
 
 /*
@@ -436,6 +441,8 @@ struct scsi_qla_host {
 	/* Map ddb_list entry by FW ddb index */
 	struct ddb_entry *fw_ddb_index_map[MAX_DDB_ENTRIES];
 
+	/* Saved srb for status continuation entry processing */
+	struct srb *status_srb;
 };
 
 static inline int is_qla4010(struct scsi_qla_host *ha)
diff --git a/drivers/scsi/qla4xxx/ql4_fw.h b/drivers/scsi/qla4xxx/ql4_fw.h
index 1b667a70cff..9cd7a608df3 100644
--- a/drivers/scsi/qla4xxx/ql4_fw.h
+++ b/drivers/scsi/qla4xxx/ql4_fw.h
@@ -572,6 +572,7 @@ struct conn_event_log_entry {
  *************************************************************************/
 #define IOCB_MAX_CDB_LEN	    16	/* Bytes in a CBD */
 #define IOCB_MAX_SENSEDATA_LEN	    32	/* Bytes of sense data */
+#define IOCB_MAX_EXT_SENSEDATA_LEN  60  /* Bytes of extended sense data */
 
 /* IOCB header structure */
 struct qla4_header {
@@ -733,6 +734,12 @@ struct status_entry {
 
 };
 
+/* Status Continuation entry */
+struct status_cont_entry {
+       struct qla4_header hdr; /* 00-03 */
+       uint8_t ext_sense_data[IOCB_MAX_EXT_SENSEDATA_LEN]; /* 04-63 */
+};
+
 struct passthru0 {
 	struct qla4_header hdr;		       /* 00-03 */
 	uint32_t handle;	/* 04-07 */
diff --git a/drivers/scsi/qla4xxx/ql4_isr.c b/drivers/scsi/qla4xxx/ql4_isr.c
index 799120fcb9b..8025ee16588 100644
--- a/drivers/scsi/qla4xxx/ql4_isr.c
+++ b/drivers/scsi/qla4xxx/ql4_isr.c
@@ -10,6 +10,98 @@
 #include "ql4_dbg.h"
 #include "ql4_inline.h"
 
+/**
+ * qla4xxx_copy_sense - copy sense data	into cmd sense buffer
+ * @ha: Pointer to host adapter structure.
+ * @sts_entry: Pointer to status entry structure.
+ * @srb: Pointer to srb structure.
+ **/
+static void qla4xxx_copy_sense(struct scsi_qla_host *ha,
+                               struct status_entry *sts_entry,
+                               struct srb *srb)
+{
+	struct scsi_cmnd *cmd = srb->cmd;
+	uint16_t sense_len;
+
+	memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE);
+	sense_len = le16_to_cpu(sts_entry->senseDataByteCnt);
+	if (sense_len == 0)
+		return;
+
+	/* Save total available sense length,
+	 * not to exceed cmd's sense buffer size */
+	sense_len = min_t(uint16_t, sense_len, SCSI_SENSE_BUFFERSIZE);
+	srb->req_sense_ptr = cmd->sense_buffer;
+	srb->req_sense_len = sense_len;
+
+	/* Copy sense from sts_entry pkt */
+	sense_len = min_t(uint16_t, sense_len, IOCB_MAX_SENSEDATA_LEN);
+	memcpy(cmd->sense_buffer, sts_entry->senseData, sense_len);
+
+	DEBUG2(printk(KERN_INFO "scsi%ld:%d:%d:%d: %s: sense key = %x, "
+		"ASL= %02x, ASC/ASCQ = %02x/%02x\n", ha->host_no,
+		cmd->device->channel, cmd->device->id,
+		cmd->device->lun, __func__,
+		sts_entry->senseData[2] & 0x0f,
+		sts_entry->senseData[7],
+		sts_entry->senseData[12],
+		sts_entry->senseData[13]));
+
+	DEBUG5(qla4xxx_dump_buffer(cmd->sense_buffer, sense_len));
+	srb->flags |= SRB_GOT_SENSE;
+
+	/* Update srb, in case a sts_cont pkt follows */
+	srb->req_sense_ptr += sense_len;
+	srb->req_sense_len -= sense_len;
+	if (srb->req_sense_len != 0)
+		ha->status_srb = srb;
+	else
+		ha->status_srb = NULL;
+}
+
+/**
+ * qla4xxx_status_cont_entry - Process a Status Continuations entry.
+ * @ha: SCSI driver HA context
+ * @sts_cont: Entry pointer
+ *
+ * Extended sense data.
+ */
+static void
+qla4xxx_status_cont_entry(struct scsi_qla_host *ha,
+			  struct status_cont_entry *sts_cont)
+{
+	struct srb *srb = ha->status_srb;
+	struct scsi_cmnd *cmd;
+	uint8_t sense_len;
+
+	if (srb == NULL)
+		return;
+
+	cmd = srb->cmd;
+	if (cmd == NULL) {
+		DEBUG2(printk(KERN_INFO "scsi%ld: %s: Cmd already returned "
+			"back to OS srb=%p srb->state:%d\n", ha->host_no,
+			__func__, srb, srb->state));
+		ha->status_srb = NULL;
+		return;
+	}
+
+	/* Copy sense data. */
+	sense_len = min_t(uint16_t, srb->req_sense_len,
+			  IOCB_MAX_EXT_SENSEDATA_LEN);
+	memcpy(srb->req_sense_ptr, sts_cont->ext_sense_data, sense_len);
+	DEBUG5(qla4xxx_dump_buffer(srb->req_sense_ptr, sense_len));
+
+	srb->req_sense_ptr += sense_len;
+	srb->req_sense_len -= sense_len;
+
+	/* Place command on done queue. */
+	if (srb->req_sense_len == 0) {
+		qla4xxx_srb_compl(ha, srb);
+		ha->status_srb = NULL;
+	}
+}
+
 /**
  * qla4xxx_status_entry - processes status IOCBs
  * @ha: Pointer to host adapter structure.
@@ -23,7 +115,6 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha,
 	struct srb *srb;
 	struct ddb_entry *ddb_entry;
 	uint32_t residual;
-	uint16_t sensebytecnt;
 
 	srb = qla4xxx_del_from_active_array(ha, le32_to_cpu(sts_entry->handle));
 	if (!srb) {
@@ -92,24 +183,7 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha,
 			break;
 
 		/* Copy Sense Data into sense buffer. */
-		memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE);
-
-		sensebytecnt = le16_to_cpu(sts_entry->senseDataByteCnt);
-		if (sensebytecnt == 0)
-			break;
-
-		memcpy(cmd->sense_buffer, sts_entry->senseData,
-		       min_t(uint16_t, sensebytecnt, SCSI_SENSE_BUFFERSIZE));
-
-		DEBUG2(printk("scsi%ld:%d:%d:%d: %s: sense key = %x, "
-			      "ASC/ASCQ = %02x/%02x\n", ha->host_no,
-			      cmd->device->channel, cmd->device->id,
-			      cmd->device->lun, __func__,
-			      sts_entry->senseData[2] & 0x0f,
-			      sts_entry->senseData[12],
-			      sts_entry->senseData[13]));
-
-		srb->flags |= SRB_GOT_SENSE;
+		qla4xxx_copy_sense(ha, sts_entry, srb);
 		break;
 
 	case SCS_INCOMPLETE:
@@ -176,23 +250,7 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha,
 				break;
 
 			/* Copy Sense Data into sense buffer. */
-			memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE);
-
-			sensebytecnt =
-				le16_to_cpu(sts_entry->senseDataByteCnt);
-			if (sensebytecnt == 0)
-				break;
-
-			memcpy(cmd->sense_buffer, sts_entry->senseData,
-			       min_t(uint16_t, sensebytecnt, SCSI_SENSE_BUFFERSIZE));
-
-			DEBUG2(printk("scsi%ld:%d:%d:%d: %s: sense key = %x, "
-				      "ASC/ASCQ = %02x/%02x\n", ha->host_no,
-				      cmd->device->channel, cmd->device->id,
-				      cmd->device->lun, __func__,
-				      sts_entry->senseData[2] & 0x0f,
-				      sts_entry->senseData[12],
-				      sts_entry->senseData[13]));
+			qla4xxx_copy_sense(ha, sts_entry, srb);
 		} else {
 			/*
 			 * If RISC reports underrun and target does not
@@ -268,9 +326,10 @@ static void qla4xxx_status_entry(struct scsi_qla_host *ha,
 
 status_entry_exit:
 
-	/* complete the request */
+	/* complete the request, if not waiting for status_continuation pkt */
 	srb->cc_stat = sts_entry->completionStatus;
-	qla4xxx_srb_compl(ha, srb);
+	if (ha->status_srb == NULL)
+		qla4xxx_srb_compl(ha, srb);
 }
 
 /**
@@ -305,10 +364,7 @@ static void qla4xxx_process_response_queue(struct scsi_qla_host * ha)
 		/* process entry */
 		switch (sts_entry->hdr.entryType) {
 		case ET_STATUS:
-			/*
-			 * Common status - Single completion posted in single
-			 * IOSB.
-			 */
+			/* Common status */
 			qla4xxx_status_entry(ha, sts_entry);
 			break;
 
@@ -316,9 +372,8 @@ static void qla4xxx_process_response_queue(struct scsi_qla_host * ha)
 			break;
 
 		case ET_STATUS_CONTINUATION:
-			/* Just throw away the status continuation entries */
-			DEBUG2(printk("scsi%ld: %s: Status Continuation entry "
-				      "- ignoring\n", ha->host_no, __func__));
+			qla4xxx_status_cont_entry(ha,
+				(struct status_cont_entry *) sts_entry);
 			break;
 
 		case ET_COMMAND:
diff --git a/drivers/scsi/qla4xxx/ql4_version.h b/drivers/scsi/qla4xxx/ql4_version.h
index ab984cb89ce..6980cb279c8 100644
--- a/drivers/scsi/qla4xxx/ql4_version.h
+++ b/drivers/scsi/qla4xxx/ql4_version.h
@@ -5,5 +5,5 @@
  * See LICENSE.qla4xxx for copyright and licensing details.
  */
 
-#define QLA4XXX_DRIVER_VERSION	"5.01.00-k8"
+#define QLA4XXX_DRIVER_VERSION	"5.01.00-k9"
 
-- 
GitLab


From 5c656af7e4edfe44c85034d6fa7002909f9c3c59 Mon Sep 17 00:00:00 2001
From: Mike Christie <michaelc@cs.wisc.edu>
Date: Wed, 15 Jul 2009 15:02:59 -0500
Subject: [PATCH 0337/1153] [SCSI] qla4xxx: add timeout handler

Recently dm-multipath began calling blk_abort_queue. This causes all the
commands/request running on the path to have the timeout function called.
If a path does go down, and the LLD returns DID_*, dm-multpiath will eventually
get this error and begin to call the cmd timeout handler. qla4xxx currently
does not set a timed out handler and so the default one could return
BLK_EH_NOT_HANDLED and end up firing the scsi eh and stopping IO to all
paths on the host when only one path is affected.

For software and offload iscsi we have a timed out handler already.
This patch adds a driver specific one to qla4xxx because there
are some ddb->state and session->state and command completion races
that are better handled in the LLD.

This also handles the problem where if the session is down,
we do not need the scsi eh to run until the transport code
has tried to reconnect us.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/scsi/qla4xxx/ql4_os.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c
index ec9da6ce848..6841883b361 100644
--- a/drivers/scsi/qla4xxx/ql4_os.c
+++ b/drivers/scsi/qla4xxx/ql4_os.c
@@ -66,6 +66,7 @@ static int qla4xxx_sess_get_param(struct iscsi_cls_session *sess,
 static int qla4xxx_host_get_param(struct Scsi_Host *shost,
 				  enum iscsi_host_param param, char *buf);
 static void qla4xxx_recovery_timedout(struct iscsi_cls_session *session);
+static enum blk_eh_timer_return qla4xxx_eh_cmd_timed_out(struct scsi_cmnd *sc);
 
 /*
  * SCSI host template entry points
@@ -89,6 +90,7 @@ static struct scsi_host_template qla4xxx_driver_template = {
 	.eh_device_reset_handler = qla4xxx_eh_device_reset,
 	.eh_target_reset_handler = qla4xxx_eh_target_reset,
 	.eh_host_reset_handler	= qla4xxx_eh_host_reset,
+	.eh_timed_out		= qla4xxx_eh_cmd_timed_out,
 
 	.slave_configure	= qla4xxx_slave_configure,
 	.slave_alloc		= qla4xxx_slave_alloc,
@@ -124,6 +126,21 @@ static struct iscsi_transport qla4xxx_iscsi_transport = {
 
 static struct scsi_transport_template *qla4xxx_scsi_transport;
 
+static enum blk_eh_timer_return qla4xxx_eh_cmd_timed_out(struct scsi_cmnd *sc)
+{
+	struct iscsi_cls_session *session;
+	struct ddb_entry *ddb_entry;
+
+	session = starget_to_session(scsi_target(sc->device));
+	ddb_entry = session->dd_data;
+
+	/* if we are not logged in then the LLD is going to clean up the cmd */
+	if (atomic_read(&ddb_entry->state) != DDB_STATE_ONLINE)
+		return BLK_EH_RESET_TIMER;
+	else
+		return BLK_EH_NOT_HANDLED;
+}
+
 static void qla4xxx_recovery_timedout(struct iscsi_cls_session *session)
 {
 	struct ddb_entry *ddb_entry = session->dd_data;
-- 
GitLab


From dca05c4c07c48da0509708d9e562578d269e90e5 Mon Sep 17 00:00:00 2001
From: Karen Higgins <karen.higgins@qlogic.com>
Date: Wed, 15 Jul 2009 15:03:00 -0500
Subject: [PATCH 0338/1153] [SCSI] qla4xxx: Fix Driver Fault Recovery
 Completion

Fixed driver bug where adapter recovery did not complete if there were
outstanding commands detected on that host adapter.

Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/scsi/qla4xxx/ql4_os.c | 19 +++++++++----------
 1 file changed, 9 insertions(+), 10 deletions(-)

diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c
index 6841883b361..e1cc0d21d89 100644
--- a/drivers/scsi/qla4xxx/ql4_os.c
+++ b/drivers/scsi/qla4xxx/ql4_os.c
@@ -921,18 +921,17 @@ static int qla4xxx_recover_adapter(struct scsi_qla_host *ha,
 	/* Flush any pending ddb changed AENs */
 	qla4xxx_process_aen(ha, FLUSH_DDB_CHANGED_AENS);
 
+	qla4xxx_flush_active_srbs(ha);
+
 	/* Reset the firmware.	If successful, function
 	 * returns with ISP interrupts enabled.
 	 */
-	if (status == QLA_SUCCESS) {
-		DEBUG2(printk("scsi%ld: %s - Performing soft reset..\n",
-			      ha->host_no, __func__));
-		qla4xxx_flush_active_srbs(ha);
-		if (ql4xxx_lock_drvr_wait(ha) == QLA_SUCCESS)
-			status = qla4xxx_soft_reset(ha);
-		else
-			status = QLA_ERROR;
-	}
+	DEBUG2(printk("scsi%ld: %s - Performing soft reset..\n",
+		      ha->host_no, __func__));
+	if (ql4xxx_lock_drvr_wait(ha) == QLA_SUCCESS)
+		status = qla4xxx_soft_reset(ha);
+	else
+		status = QLA_ERROR;
 
 	/* Flush any pending ddb changed AENs */
 	qla4xxx_process_aen(ha, FLUSH_DDB_CHANGED_AENS);
@@ -1661,7 +1660,7 @@ static int qla4xxx_eh_host_reset(struct scsi_cmnd *cmd)
 	ha = (struct scsi_qla_host *) cmd->device->host->hostdata;
 
 	dev_info(&ha->pdev->dev,
-		   "scsi(%ld:%d:%d:%d): ADAPTER RESET ISSUED.\n", ha->host_no,
+		   "scsi(%ld:%d:%d:%d): HOST RESET ISSUED.\n", ha->host_no,
 		   cmd->device->channel, cmd->device->id, cmd->device->lun);
 
 	if (qla4xxx_wait_for_hba_online(ha) != QLA_SUCCESS) {
-- 
GitLab


From 612f73488785829d4f34aad00bfe30b904c94c9e Mon Sep 17 00:00:00 2001
From: Karen Higgins <karen.higgins@qlogic.com>
Date: Wed, 15 Jul 2009 15:03:01 -0500
Subject: [PATCH 0339/1153] [SCSI] qla4xxx: Fix srb lookup in
 qla4xxx_eh_device_reset

eh_device_reset may be called from scsi error handler or sg_reset, etc.
When called from sg_reset, there will not be an associated srb.  The
driver should lookup the corresponding device handle given information
from the supplied cmd structure and should not assume that there exists
an srb.

Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/scsi/qla4xxx/ql4_os.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c
index e1cc0d21d89..40e3cafb3a9 100644
--- a/drivers/scsi/qla4xxx/ql4_os.c
+++ b/drivers/scsi/qla4xxx/ql4_os.c
@@ -1543,11 +1543,9 @@ static int qla4xxx_eh_device_reset(struct scsi_cmnd *cmd)
 {
 	struct scsi_qla_host *ha = to_qla_host(cmd->device->host);
 	struct ddb_entry *ddb_entry = cmd->device->hostdata;
-	struct srb *sp;
 	int ret = FAILED, stat;
 
-	sp = (struct srb *) cmd->SCp.ptr;
-	if (!sp || !ddb_entry)
+	if (!ddb_entry)
 		return ret;
 
 	dev_info(&ha->pdev->dev,
-- 
GitLab


From 16ed55f9de6743ceece9bf528362cadff10f1c5c Mon Sep 17 00:00:00 2001
From: Karen Higgins <karen.higgins@qlogic.com>
Date: Wed, 15 Jul 2009 15:03:02 -0500
Subject: [PATCH 0340/1153] [SCSI] qla4xxx: Remove hiwat code so scsi eh does
 not get escalated when we can make progress

Removed unnecessary hiwat code to free up the number available IOCBs.
Eliminates unnecessary eh_ escalations due to inability to obtain IOCB
pkt for marker.

v2.
- Remove define not used anymore and fix req_q_coun accounting.

Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
[michaelc: ported patch from qlogic.com driver to upstream]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/scsi/qla4xxx/ql4_def.h  |   2 -
 drivers/scsi/qla4xxx/ql4_iocb.c | 133 ++++++++++++++------------------
 drivers/scsi/qla4xxx/ql4_mbx.c  |  10 ---
 3 files changed, 60 insertions(+), 85 deletions(-)

diff --git a/drivers/scsi/qla4xxx/ql4_def.h b/drivers/scsi/qla4xxx/ql4_def.h
index 963e8553d21..81b5f29254e 100644
--- a/drivers/scsi/qla4xxx/ql4_def.h
+++ b/drivers/scsi/qla4xxx/ql4_def.h
@@ -100,7 +100,6 @@
 #define MAX_SRBS		MAX_CMDS_TO_RISC
 #define MBOX_AEN_REG_COUNT	5
 #define MAX_INIT_RETRIES	5
-#define IOCB_HIWAT_CUSHION	16
 
 /*
  * Buffer sizes
@@ -307,7 +306,6 @@ struct scsi_qla_host {
 	uint32_t tot_ddbs;
 
 	uint16_t	iocb_cnt;
-	uint16_t	iocb_hiwat;
 
 	/* SRB cache. */
 #define SRB_MIN_REQ	128
diff --git a/drivers/scsi/qla4xxx/ql4_iocb.c b/drivers/scsi/qla4xxx/ql4_iocb.c
index 912a67494ad..e0c32159749 100644
--- a/drivers/scsi/qla4xxx/ql4_iocb.c
+++ b/drivers/scsi/qla4xxx/ql4_iocb.c
@@ -10,9 +10,42 @@
 #include "ql4_dbg.h"
 #include "ql4_inline.h"
 
-
 #include <scsi/scsi_tcq.h>
 
+static int
+qla4xxx_space_in_req_ring(struct scsi_qla_host *ha, uint16_t req_cnt)
+{
+	uint16_t cnt;
+
+	/* Calculate number of free request entries. */
+	if ((req_cnt + 2) >= ha->req_q_count) {
+		cnt = (uint16_t) le32_to_cpu(ha->shadow_regs->req_q_out);
+		if (ha->request_in < cnt)
+			ha->req_q_count = cnt - ha->request_in;
+		else
+			ha->req_q_count = REQUEST_QUEUE_DEPTH -
+						(ha->request_in - cnt);
+	}
+
+	/* Check if room for request in request ring. */
+	if ((req_cnt + 2) < ha->req_q_count)
+		return 1;
+	else
+		return 0;
+}
+
+static void qla4xxx_advance_req_ring_ptr(struct scsi_qla_host *ha)
+{
+	/* Advance request queue pointer */
+	if (ha->request_in == (REQUEST_QUEUE_DEPTH - 1)) {
+		ha->request_in = 0;
+		ha->request_ptr = ha->request_ring;
+	} else {
+		ha->request_in++;
+		ha->request_ptr++;
+	}
+}
+
 /**
  * qla4xxx_get_req_pkt - returns a valid entry in request queue.
  * @ha: Pointer to host adapter structure.
@@ -26,35 +59,18 @@
 static int qla4xxx_get_req_pkt(struct scsi_qla_host *ha,
 			       struct queue_entry **queue_entry)
 {
-	uint16_t request_in;
-	uint8_t status = QLA_SUCCESS;
-
-	*queue_entry = ha->request_ptr;
+	uint16_t req_cnt = 1;
 
-	/* get the latest request_in and request_out index */
-	request_in = ha->request_in;
-	ha->request_out = (uint16_t) le32_to_cpu(ha->shadow_regs->req_q_out);
-
-	/* Advance request queue pointer and check for queue full */
-	if (request_in == (REQUEST_QUEUE_DEPTH - 1)) {
-		request_in = 0;
-		ha->request_ptr = ha->request_ring;
-	} else {
-		request_in++;
-		ha->request_ptr++;
-	}
-
-	/* request queue is full, try again later */
-	if ((ha->iocb_cnt + 1) >= ha->iocb_hiwat) {
-		/* restore request pointer */
-		ha->request_ptr = *queue_entry;
-		status = QLA_ERROR;
-	} else {
-		ha->request_in = request_in;
+	if (qla4xxx_space_in_req_ring(ha, req_cnt)) {
+		*queue_entry = ha->request_ptr;
 		memset(*queue_entry, 0, sizeof(**queue_entry));
+
+		qla4xxx_advance_req_ring_ptr(ha);
+		ha->req_q_count -= req_cnt;
+		return QLA_SUCCESS;
 	}
 
-	return status;
+	return QLA_ERROR;
 }
 
 /**
@@ -100,21 +116,14 @@ exit_send_marker:
 	return status;
 }
 
-static struct continuation_t1_entry* qla4xxx_alloc_cont_entry(
-	struct scsi_qla_host *ha)
+static struct continuation_t1_entry *
+qla4xxx_alloc_cont_entry(struct scsi_qla_host *ha)
 {
 	struct continuation_t1_entry *cont_entry;
 
 	cont_entry = (struct continuation_t1_entry *)ha->request_ptr;
 
-	/* Advance request queue pointer */
-	if (ha->request_in == (REQUEST_QUEUE_DEPTH - 1)) {
-		ha->request_in = 0;
-		ha->request_ptr = ha->request_ring;
-	} else {
-		ha->request_in++;
-		ha->request_ptr++;
-	}
+	qla4xxx_advance_req_ring_ptr(ha);
 
 	/* Load packet defaults */
 	cont_entry->hdr.entryType = ET_CONTINUE;
@@ -197,13 +206,10 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb)
 	struct scsi_cmnd *cmd = srb->cmd;
 	struct ddb_entry *ddb_entry;
 	struct command_t3_entry *cmd_entry;
-
 	int nseg;
 	uint16_t tot_dsds;
 	uint16_t req_cnt;
-
 	unsigned long flags;
-	uint16_t cnt;
 	uint32_t index;
 	char tag[2];
 
@@ -217,6 +223,19 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb)
 
 	index = (uint32_t)cmd->request->tag;
 
+	/*
+	 * Check to see if adapter is online before placing request on
+	 * request queue.  If a reset occurs and a request is in the queue,
+	 * the firmware will still attempt to process the request, retrieving
+	 * garbage for pointers.
+	 */
+	if (!test_bit(AF_ONLINE, &ha->flags)) {
+		DEBUG2(printk("scsi%ld: %s: Adapter OFFLINE! "
+			      "Do not issue command.\n",
+			      ha->host_no, __func__));
+		goto queuing_error;
+	}
+
 	/* Calculate the number of request entries needed. */
 	nseg = scsi_dma_map(cmd);
 	if (nseg < 0)
@@ -224,17 +243,7 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb)
 	tot_dsds = nseg;
 
 	req_cnt = qla4xxx_calc_request_entries(tot_dsds);
-
-	if (ha->req_q_count < (req_cnt + 2)) {
-		cnt = (uint16_t) le32_to_cpu(ha->shadow_regs->req_q_out);
-		if (ha->request_in < cnt)
-			ha->req_q_count = cnt - ha->request_in;
-		else
-			ha->req_q_count = REQUEST_QUEUE_DEPTH -
-				(ha->request_in - cnt);
-	}
-
-	if (ha->req_q_count < (req_cnt + 2))
+	if (!qla4xxx_space_in_req_ring(ha, req_cnt))
 		goto queuing_error;
 
 	/* total iocbs active */
@@ -286,32 +295,10 @@ int qla4xxx_send_command_to_isp(struct scsi_qla_host *ha, struct srb * srb)
 			break;
 		}
 
-
-	/* Advance request queue pointer */
-	ha->request_in++;
-	if (ha->request_in == REQUEST_QUEUE_DEPTH) {
-		ha->request_in = 0;
-		ha->request_ptr = ha->request_ring;
-	} else
-		ha->request_ptr++;
-
-
+	qla4xxx_advance_req_ring_ptr(ha);
 	qla4xxx_build_scsi_iocbs(srb, cmd_entry, tot_dsds);
 	wmb();
 
-	/*
-	 * Check to see if adapter is online before placing request on
-	 * request queue.  If a reset occurs and a request is in the queue,
-	 * the firmware will still attempt to process the request, retrieving
-	 * garbage for pointers.
-	 */
-	if (!test_bit(AF_ONLINE, &ha->flags)) {
-		DEBUG2(printk("scsi%ld: %s: Adapter OFFLINE! "
-			      "Do not issue command.\n",
-			      ha->host_no, __func__));
-		goto queuing_error;
-	}
-
 	srb->cmd->host_scribble = (unsigned char *)srb;
 
 	/* update counters */
diff --git a/drivers/scsi/qla4xxx/ql4_mbx.c b/drivers/scsi/qla4xxx/ql4_mbx.c
index 051b0f5e8c8..09d6d4b76f3 100644
--- a/drivers/scsi/qla4xxx/ql4_mbx.c
+++ b/drivers/scsi/qla4xxx/ql4_mbx.c
@@ -385,16 +385,6 @@ int qla4xxx_get_firmware_status(struct scsi_qla_host * ha)
 			      mbox_sts[0]));
 		return QLA_ERROR;
 	}
-
-	/* High-water mark of IOCBs */
-	ha->iocb_hiwat = mbox_sts[2];
-	if (ha->iocb_hiwat > IOCB_HIWAT_CUSHION)
-		ha->iocb_hiwat -= IOCB_HIWAT_CUSHION;
-	else
-		dev_info(&ha->pdev->dev, "WARNING!!!  You have less than %d "
-			   "firmware IOCBs available (%d).\n",
-			   IOCB_HIWAT_CUSHION, ha->iocb_hiwat);
-
 	return QLA_SUCCESS;
 }
 
-- 
GitLab


From a0cc1ecc098e31d03b3265712a3e280a7fabf438 Mon Sep 17 00:00:00 2001
From: Vasu Dev <vasu.dev@intel.com>
Date: Tue, 28 Jul 2009 17:33:37 -0700
Subject: [PATCH 0341/1153] [SCSI] libfc: fix a circular locking warning during
 sending RRQ

Currently the fc_exch_rrq is called with fc_exch's ex_lock held.
The fc_exch_rrq allocates new exch and that requires taking
ex_lock again after EM lock. This locking order causes warning,
see more details on this warning at :-

 http://www.open-fcoe.org/pipermail/devel/2009-July/003251.html

This patch fixes this by dropping the ex_lock before calling
fc_exch_rrq().

The fc_exch_rrq needs to grab ex_lock lock again to schedule
RRQ retry and in the meanwhile fc_exch_reset could occur before
ex_lock is grabbed inside fc_exch_rrq. So to handle this case,
this patch adds additional check to detect fc_exch_reset after
ex_lock acquired and in case the fc_exch_reset occurred then
abandons the RRQ retry and releases the exch.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/scsi/libfc/fc_exch.c | 23 +++++++++++++++--------
 1 file changed, 15 insertions(+), 8 deletions(-)

diff --git a/drivers/scsi/libfc/fc_exch.c b/drivers/scsi/libfc/fc_exch.c
index 2bc22be5f84..145ab9ba55e 100644
--- a/drivers/scsi/libfc/fc_exch.c
+++ b/drivers/scsi/libfc/fc_exch.c
@@ -415,9 +415,9 @@ static void fc_exch_timeout(struct work_struct *work)
 	e_stat = ep->esb_stat;
 	if (e_stat & ESB_ST_COMPLETE) {
 		ep->esb_stat = e_stat & ~ESB_ST_REC_QUAL;
+		spin_unlock_bh(&ep->ex_lock);
 		if (e_stat & ESB_ST_REC_QUAL)
 			fc_exch_rrq(ep);
-		spin_unlock_bh(&ep->ex_lock);
 		goto done;
 	} else {
 		resp = ep->resp;
@@ -1624,14 +1624,14 @@ static void fc_exch_rrq(struct fc_exch *ep)
 	struct fc_lport *lp;
 	struct fc_els_rrq *rrq;
 	struct fc_frame *fp;
-	struct fc_seq *rrq_sp;
 	u32 did;
 
 	lp = ep->lp;
 
 	fp = fc_frame_alloc(lp, sizeof(*rrq));
 	if (!fp)
-		return;
+		goto retry;
+
 	rrq = fc_frame_payload_get(fp, sizeof(*rrq));
 	memset(rrq, 0, sizeof(*rrq));
 	rrq->rrq_cmd = ELS_RRQ;
@@ -1647,13 +1647,20 @@ static void fc_exch_rrq(struct fc_exch *ep)
 		       fc_host_port_id(lp->host), FC_TYPE_ELS,
 		       FC_FC_FIRST_SEQ | FC_FC_END_SEQ | FC_FC_SEQ_INIT, 0);
 
-	rrq_sp = fc_exch_seq_send(lp, fp, fc_exch_rrq_resp, NULL, ep,
-				  lp->e_d_tov);
-	if (!rrq_sp) {
-		ep->esb_stat |= ESB_ST_REC_QUAL;
-		fc_exch_timer_set_locked(ep, ep->r_a_tov);
+	if (fc_exch_seq_send(lp, fp, fc_exch_rrq_resp, NULL, ep, lp->e_d_tov))
+		return;
+
+retry:
+	spin_lock_bh(&ep->ex_lock);
+	if (ep->state & (FC_EX_RST_CLEANUP | FC_EX_DONE)) {
+		spin_unlock_bh(&ep->ex_lock);
+		/* drop hold for rec qual */
+		fc_exch_release(ep);
 		return;
 	}
+	ep->esb_stat |= ESB_ST_REC_QUAL;
+	fc_exch_timer_set_locked(ep, ep->r_a_tov);
+	spin_unlock_bh(&ep->ex_lock);
 }
 
 
-- 
GitLab


From f36f3042eae238bdaefe7c79310afe573bfc3622 Mon Sep 17 00:00:00 2001
From: Chris Mason <chris.mason@oracle.com>
Date: Thu, 30 Jul 2009 10:04:48 -0400
Subject: [PATCH 0342/1153] Btrfs: be more polite in the async caching threads

The semaphore used by the async caching threads can prevent a
transaction commit, which can make the FS appear to stall.  This
releases the semaphore more often when a transaction commit is
in progress.

Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/extent-tree.c |  5 +++--
 fs/btrfs/transaction.c | 10 ++++++++++
 fs/btrfs/transaction.h |  1 +
 3 files changed, 14 insertions(+), 2 deletions(-)

diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index 2fe21fa7491..dc84daee6bc 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -302,10 +302,11 @@ again:
 			else if (ret)
 				break;
 
-			if (need_resched()) {
+			if (need_resched() ||
+			    btrfs_transaction_in_commit(fs_info)) {
 				btrfs_release_path(fs_info->extent_root, path);
 				up_read(&fs_info->extent_commit_sem);
-				cond_resched();
+				schedule_timeout(1);
 				goto again;
 			}
 
diff --git a/fs/btrfs/transaction.c b/fs/btrfs/transaction.c
index de48e4ec808..cdbb5022da5 100644
--- a/fs/btrfs/transaction.c
+++ b/fs/btrfs/transaction.c
@@ -857,6 +857,16 @@ static void update_super_roots(struct btrfs_root *root)
 	super->root_level = root_item->level;
 }
 
+int btrfs_transaction_in_commit(struct btrfs_fs_info *info)
+{
+	int ret = 0;
+	spin_lock(&info->new_trans_lock);
+	if (info->running_transaction)
+		ret = info->running_transaction->in_commit;
+	spin_unlock(&info->new_trans_lock);
+	return ret;
+}
+
 int btrfs_commit_transaction(struct btrfs_trans_handle *trans,
 			     struct btrfs_root *root)
 {
diff --git a/fs/btrfs/transaction.h b/fs/btrfs/transaction.h
index 961c3ee5a2e..663c6740491 100644
--- a/fs/btrfs/transaction.h
+++ b/fs/btrfs/transaction.h
@@ -107,4 +107,5 @@ int btrfs_record_root_in_trans(struct btrfs_trans_handle *trans,
 				struct btrfs_root *root);
 int btrfs_write_and_wait_marked_extents(struct btrfs_root *root,
 					struct extent_io_tree *dirty_pages);
+int btrfs_transaction_in_commit(struct btrfs_fs_info *info);
 #endif
-- 
GitLab


From 19252de6818ced0def0551d64a0a2975f52a523d Mon Sep 17 00:00:00 2001
From: Tom Peng <tom_peng@usish.com>
Date: Fri, 17 Jul 2009 16:02:04 +0800
Subject: [PATCH 0343/1153] [SCSI] libsas: fix wide port hotplug issues

Hotplug of phys which form wide ports simply does not work at the moment.  Fix
this by adding checks at the hotplug points to see if the attached sas address
of the phy already exists (in which case it's part of a wide port) and act
accordingly.

Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
[jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower
 case to fix a ppc64 compile error in linux-next]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/scsi/libsas/sas_expander.c | 147 +++++++++++++++++++++--------
 1 file changed, 107 insertions(+), 40 deletions(-)

diff --git a/drivers/scsi/libsas/sas_expander.c b/drivers/scsi/libsas/sas_expander.c
index 54fa1e42dc4..b3381959acc 100644
--- a/drivers/scsi/libsas/sas_expander.c
+++ b/drivers/scsi/libsas/sas_expander.c
@@ -766,6 +766,7 @@ static int sas_ex_join_wide_port(struct domain_device *parent, int phy_id)
 		if (!memcmp(phy->attached_sas_addr, ephy->attached_sas_addr,
 			    SAS_ADDR_SIZE) && ephy->port) {
 			sas_port_add_phy(ephy->port, phy->phy);
+			phy->port = ephy->port;
 			phy->phy_state = PHY_DEVICE_DISCOVERED;
 			return 0;
 		}
@@ -945,11 +946,21 @@ static int sas_ex_discover_dev(struct domain_device *dev, int phy_id)
 			if (ex->ex_phy[i].phy_state == PHY_VACANT ||
 			    ex->ex_phy[i].phy_state == PHY_NOT_PRESENT)
 				continue;
-
+			/*
+			 * Due to races, the phy might not get added to the
+			 * wide port, so we add the phy to the wide port here.
+			 */
 			if (SAS_ADDR(ex->ex_phy[i].attached_sas_addr) ==
-			    SAS_ADDR(child->sas_addr))
+			    SAS_ADDR(child->sas_addr)) {
 				ex->ex_phy[i].phy_state= PHY_DEVICE_DISCOVERED;
+				res = sas_ex_join_wide_port(dev, i);
+				if (!res)
+					SAS_DPRINTK("Attaching ex phy%d to wide port %016llx\n",
+						    i, SAS_ADDR(ex->ex_phy[i].attached_sas_addr));
+
+			}
 		}
+		res = 0;
 	}
 
 	return res;
@@ -1598,7 +1609,7 @@ static int sas_get_phy_attached_sas_addr(struct domain_device *dev,
 }
 
 static int sas_find_bcast_phy(struct domain_device *dev, int *phy_id,
-			      int from_phy)
+			      int from_phy, bool update)
 {
 	struct expander_device *ex = &dev->ex_dev;
 	int res = 0;
@@ -1611,7 +1622,9 @@ static int sas_find_bcast_phy(struct domain_device *dev, int *phy_id,
 		if (res)
 			goto out;
 		else if (phy_change_count != ex->ex_phy[i].phy_change_count) {
-			ex->ex_phy[i].phy_change_count = phy_change_count;
+			if (update)
+				ex->ex_phy[i].phy_change_count =
+					phy_change_count;
 			*phy_id = i;
 			return 0;
 		}
@@ -1653,31 +1666,52 @@ out:
 	kfree(rg_req);
 	return res;
 }
+/**
+ * sas_find_bcast_dev -  find the device issue BROADCAST(CHANGE).
+ * @dev:domain device to be detect.
+ * @src_dev: the device which originated BROADCAST(CHANGE).
+ *
+ * Add self-configuration expander suport. Suppose two expander cascading,
+ * when the first level expander is self-configuring, hotplug the disks in
+ * second level expander, BROADCAST(CHANGE) will not only be originated
+ * in the second level expander, but also be originated in the first level
+ * expander (see SAS protocol SAS 2r-14, 7.11 for detail), it is to say,
+ * expander changed count in two level expanders will all increment at least
+ * once, but the phy which chang count has changed is the source device which
+ * we concerned.
+ */
 
 static int sas_find_bcast_dev(struct domain_device *dev,
 			      struct domain_device **src_dev)
 {
 	struct expander_device *ex = &dev->ex_dev;
 	int ex_change_count = -1;
+	int phy_id = -1;
 	int res;
+	struct domain_device *ch;
 
 	res = sas_get_ex_change_count(dev, &ex_change_count);
 	if (res)
 		goto out;
-	if (ex_change_count != -1 &&
-	    ex_change_count != ex->ex_change_count) {
-		*src_dev = dev;
-		ex->ex_change_count = ex_change_count;
-	} else {
-		struct domain_device *ch;
-
-		list_for_each_entry(ch, &ex->children, siblings) {
-			if (ch->dev_type == EDGE_DEV ||
-			    ch->dev_type == FANOUT_DEV) {
-				res = sas_find_bcast_dev(ch, src_dev);
-				if (src_dev)
-					return res;
-			}
+	if (ex_change_count != -1 && ex_change_count != ex->ex_change_count) {
+		/* Just detect if this expander phys phy change count changed,
+		* in order to determine if this expander originate BROADCAST,
+		* and do not update phy change count field in our structure.
+		*/
+		res = sas_find_bcast_phy(dev, &phy_id, 0, false);
+		if (phy_id != -1) {
+			*src_dev = dev;
+			ex->ex_change_count = ex_change_count;
+			SAS_DPRINTK("Expander phy change count has changed\n");
+			return res;
+		} else
+			SAS_DPRINTK("Expander phys DID NOT change\n");
+	}
+	list_for_each_entry(ch, &ex->children, siblings) {
+		if (ch->dev_type == EDGE_DEV || ch->dev_type == FANOUT_DEV) {
+			res = sas_find_bcast_dev(ch, src_dev);
+			if (src_dev)
+				return res;
 		}
 	}
 out:
@@ -1700,24 +1734,26 @@ static void sas_unregister_ex_tree(struct domain_device *dev)
 }
 
 static void sas_unregister_devs_sas_addr(struct domain_device *parent,
-					 int phy_id)
+					 int phy_id, bool last)
 {
 	struct expander_device *ex_dev = &parent->ex_dev;
 	struct ex_phy *phy = &ex_dev->ex_phy[phy_id];
 	struct domain_device *child, *n;
-
-	list_for_each_entry_safe(child, n, &ex_dev->children, siblings) {
-		if (SAS_ADDR(child->sas_addr) ==
-		    SAS_ADDR(phy->attached_sas_addr)) {
-			if (child->dev_type == EDGE_DEV ||
-			    child->dev_type == FANOUT_DEV)
-				sas_unregister_ex_tree(child);
-			else
-				sas_unregister_dev(child);
-			break;
+	if (last) {
+		list_for_each_entry_safe(child, n,
+			&ex_dev->children, siblings) {
+			if (SAS_ADDR(child->sas_addr) ==
+			    SAS_ADDR(phy->attached_sas_addr)) {
+				if (child->dev_type == EDGE_DEV ||
+				    child->dev_type == FANOUT_DEV)
+					sas_unregister_ex_tree(child);
+				else
+					sas_unregister_dev(child);
+				break;
+			}
 		}
+		sas_disable_routing(parent, phy->attached_sas_addr);
 	}
-	sas_disable_routing(parent, phy->attached_sas_addr);
 	memset(phy->attached_sas_addr, 0, SAS_ADDR_SIZE);
 	sas_port_delete_phy(phy->port, phy->phy);
 	if (phy->port->num_phys == 0)
@@ -1770,15 +1806,31 @@ static int sas_discover_new(struct domain_device *dev, int phy_id)
 {
 	struct ex_phy *ex_phy = &dev->ex_dev.ex_phy[phy_id];
 	struct domain_device *child;
-	int res;
+	bool found = false;
+	int res, i;
 
 	SAS_DPRINTK("ex %016llx phy%d new device attached\n",
 		    SAS_ADDR(dev->sas_addr), phy_id);
 	res = sas_ex_phy_discover(dev, phy_id);
 	if (res)
 		goto out;
+	/* to support the wide port inserted */
+	for (i = 0; i < dev->ex_dev.num_phys; i++) {
+		struct ex_phy *ex_phy_temp = &dev->ex_dev.ex_phy[i];
+		if (i == phy_id)
+			continue;
+		if (SAS_ADDR(ex_phy_temp->attached_sas_addr) ==
+		    SAS_ADDR(ex_phy->attached_sas_addr)) {
+			found = true;
+			break;
+		}
+	}
+	if (found) {
+		sas_ex_join_wide_port(dev, phy_id);
+		return 0;
+	}
 	res = sas_ex_discover_devices(dev, phy_id);
-	if (res)
+	if (!res)
 		goto out;
 	list_for_each_entry(child, &dev->ex_dev.children, siblings) {
 		if (SAS_ADDR(child->sas_addr) ==
@@ -1793,7 +1845,7 @@ out:
 	return res;
 }
 
-static int sas_rediscover_dev(struct domain_device *dev, int phy_id)
+static int sas_rediscover_dev(struct domain_device *dev, int phy_id, bool last)
 {
 	struct expander_device *ex = &dev->ex_dev;
 	struct ex_phy *phy = &ex->ex_phy[phy_id];
@@ -1804,11 +1856,11 @@ static int sas_rediscover_dev(struct domain_device *dev, int phy_id)
 	switch (res) {
 	case SMP_RESP_NO_PHY:
 		phy->phy_state = PHY_NOT_PRESENT;
-		sas_unregister_devs_sas_addr(dev, phy_id);
+		sas_unregister_devs_sas_addr(dev, phy_id, last);
 		goto out; break;
 	case SMP_RESP_PHY_VACANT:
 		phy->phy_state = PHY_VACANT;
-		sas_unregister_devs_sas_addr(dev, phy_id);
+		sas_unregister_devs_sas_addr(dev, phy_id, last);
 		goto out; break;
 	case SMP_RESP_FUNC_ACC:
 		break;
@@ -1816,7 +1868,7 @@ static int sas_rediscover_dev(struct domain_device *dev, int phy_id)
 
 	if (SAS_ADDR(attached_sas_addr) == 0) {
 		phy->phy_state = PHY_EMPTY;
-		sas_unregister_devs_sas_addr(dev, phy_id);
+		sas_unregister_devs_sas_addr(dev, phy_id, last);
 	} else if (SAS_ADDR(attached_sas_addr) ==
 		   SAS_ADDR(phy->attached_sas_addr)) {
 		SAS_DPRINTK("ex %016llx phy 0x%x broadcast flutter\n",
@@ -1828,12 +1880,27 @@ out:
 	return res;
 }
 
+/**
+ * sas_rediscover - revalidate the domain.
+ * @dev:domain device to be detect.
+ * @phy_id: the phy id will be detected.
+ *
+ * NOTE: this process _must_ quit (return) as soon as any connection
+ * errors are encountered.  Connection recovery is done elsewhere.
+ * Discover process only interrogates devices in order to discover the
+ * domain.For plugging out, we un-register the device only when it is
+ * the last phy in the port, for other phys in this port, we just delete it
+ * from the port.For inserting, we do discovery when it is the
+ * first phy,for other phys in this port, we add it to the port to
+ * forming the wide-port.
+ */
 static int sas_rediscover(struct domain_device *dev, const int phy_id)
 {
 	struct expander_device *ex = &dev->ex_dev;
 	struct ex_phy *changed_phy = &ex->ex_phy[phy_id];
 	int res = 0;
 	int i;
+	bool last = true;	/* is this the last phy of the port */
 
 	SAS_DPRINTK("ex %016llx phy%d originated BROADCAST(CHANGE)\n",
 		    SAS_ADDR(dev->sas_addr), phy_id);
@@ -1848,13 +1915,13 @@ static int sas_rediscover(struct domain_device *dev, const int phy_id)
 			    SAS_ADDR(changed_phy->attached_sas_addr)) {
 				SAS_DPRINTK("phy%d part of wide port with "
 					    "phy%d\n", phy_id, i);
-				goto out;
+				last = false;
+				break;
 			}
 		}
-		res = sas_rediscover_dev(dev, phy_id);
+		res = sas_rediscover_dev(dev, phy_id, last);
 	} else
 		res = sas_discover_new(dev, phy_id);
-out:
 	return res;
 }
 
@@ -1881,7 +1948,7 @@ int sas_ex_revalidate_domain(struct domain_device *port_dev)
 
 		do {
 			phy_id = -1;
-			res = sas_find_bcast_phy(dev, &phy_id, i);
+			res = sas_find_bcast_phy(dev, &phy_id, i, true);
 			if (phy_id == -1)
 				break;
 			res = sas_rediscover(dev, phy_id);
-- 
GitLab


From 4bf17af0dbfe4cf20cb750e22e8e926273e7a7a4 Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Tue, 14 Jul 2009 19:30:23 +0200
Subject: [PATCH 0344/1153] udf: Fix loading of VAT inode when drive wrongly
 reports number of recorded blocks

VAT inode is located in the last block recorded block of the medium. When the
drive errorneously reports number of recorded blocks, we failed to load the VAT
inode and thus mount the medium. This patch makes kernel try to read VAT inode
from the last block of the device if it is different from the last recorded
block.

Signed-off-by: Jan Kara <jack@suse.cz>
---
 fs/udf/super.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/fs/udf/super.c b/fs/udf/super.c
index 6832135159b..9d1b8c2e6c4 100644
--- a/fs/udf/super.c
+++ b/fs/udf/super.c
@@ -1087,11 +1087,23 @@ static int udf_load_vat(struct super_block *sb, int p_index, int type1_index)
 	struct udf_inode_info *vati;
 	uint32_t pos;
 	struct virtualAllocationTable20 *vat20;
+	sector_t blocks = sb->s_bdev->bd_inode->i_size >> sb->s_blocksize_bits;
 
 	/* VAT file entry is in the last recorded block */
 	ino.partitionReferenceNum = type1_index;
 	ino.logicalBlockNum = sbi->s_last_block - map->s_partition_root;
 	sbi->s_vat_inode = udf_iget(sb, &ino);
+	if (!sbi->s_vat_inode &&
+	    sbi->s_last_block != blocks - 1) {
+		printk(KERN_NOTICE "UDF-fs: Failed to read VAT inode from the"
+		       " last recorded block (%lu), retrying with the last "
+		       "block of the device (%lu).\n",
+		       (unsigned long)sbi->s_last_block,
+		       (unsigned long)blocks - 1);
+		ino.partitionReferenceNum = type1_index;
+		ino.logicalBlockNum = blocks - 1 - map->s_partition_root;
+		sbi->s_vat_inode = udf_iget(sb, &ino);
+	}
 	if (!sbi->s_vat_inode)
 		return 1;
 
-- 
GitLab


From dee865656f2d8b866f8ac22c60d6363b914e9f12 Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Wed, 22 Jul 2009 18:12:17 +0200
Subject: [PATCH 0345/1153] quota: Silence lockdep on quota_on

Commit d01730d74d2b0155da50d44555001706294014f7 didn't completely fix
the problem since we still take dqio_mutex and i_mutex in the wrong
order. Move taking of i_mutex further down (luckily it's needed only
for updating inode flags) below where dqio_mutex is taken.

Tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
---
 fs/quota/dquot.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/fs/quota/dquot.c b/fs/quota/dquot.c
index 70f36c043d6..38f7bd559f3 100644
--- a/fs/quota/dquot.c
+++ b/fs/quota/dquot.c
@@ -2043,7 +2043,6 @@ static int vfs_load_quota_inode(struct inode *inode, int type, int format_id,
 		invalidate_bdev(sb->s_bdev);
 	}
 	mutex_lock(&dqopt->dqonoff_mutex);
-	mutex_lock_nested(&inode->i_mutex, I_MUTEX_QUOTA);
 	if (sb_has_quota_loaded(sb, type)) {
 		error = -EBUSY;
 		goto out_lock;
@@ -2054,9 +2053,11 @@ static int vfs_load_quota_inode(struct inode *inode, int type, int format_id,
 		 * possible) Also nobody should write to the file - we use
 		 * special IO operations which ignore the immutable bit. */
 		down_write(&dqopt->dqptr_sem);
+		mutex_lock_nested(&inode->i_mutex, I_MUTEX_QUOTA);
 		oldflags = inode->i_flags & (S_NOATIME | S_IMMUTABLE |
 					     S_NOQUOTA);
 		inode->i_flags |= S_NOQUOTA | S_NOATIME | S_IMMUTABLE;
+		mutex_unlock(&inode->i_mutex);
 		up_write(&dqopt->dqptr_sem);
 		sb->dq_op->drop(inode);
 	}
@@ -2080,7 +2081,6 @@ static int vfs_load_quota_inode(struct inode *inode, int type, int format_id,
 		goto out_file_init;
 	}
 	mutex_unlock(&dqopt->dqio_mutex);
-	mutex_unlock(&inode->i_mutex);
 	spin_lock(&dq_state_lock);
 	dqopt->flags |= dquot_state_flag(flags, type);
 	spin_unlock(&dq_state_lock);
@@ -2096,13 +2096,14 @@ out_file_init:
 out_lock:
 	if (oldflags != -1) {
 		down_write(&dqopt->dqptr_sem);
+		mutex_lock_nested(&inode->i_mutex, I_MUTEX_QUOTA);
 		/* Set the flags back (in the case of accidental quotaon()
 		 * on a wrong file we don't want to mess up the flags) */
 		inode->i_flags &= ~(S_NOATIME | S_NOQUOTA | S_IMMUTABLE);
 		inode->i_flags |= oldflags;
+		mutex_unlock(&inode->i_mutex);
 		up_write(&dqopt->dqptr_sem);
 	}
-	mutex_unlock(&inode->i_mutex);
 	mutex_unlock(&dqopt->dqonoff_mutex);
 out_fmt:
 	put_quota_format(fmt);
-- 
GitLab


From ffd4bc2a984fab40ed969163efdff321490e8032 Mon Sep 17 00:00:00 2001
From: "Martin K. Petersen" <martin.petersen@oracle.com>
Date: Wed, 29 Jul 2009 14:06:53 -0400
Subject: [PATCH 0346/1153] [SCSI] sd: Avoid sending extended inquiry to legacy
 devices

Some USB devices crash when we send them an inquiry with the EVPD bit
set, regardless of page requested (i.e. including page 0).

We only need the extended inquiry to gain access to VPD pages 0xB0 and
0xB1.  These appeared in SBC2 and SBC3 respectively, so we can restrict
sending the extended inquiry to devices reporting SPC3 or higher.

This fixes bugzilla.kernel.org #13657.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[jejb: added comment]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
---
 drivers/scsi/sd.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/sd.c b/drivers/scsi/sd.c
index 5616cd780ff..b7b9fec67a9 100644
--- a/drivers/scsi/sd.c
+++ b/drivers/scsi/sd.c
@@ -1840,6 +1840,18 @@ static void sd_read_block_characteristics(struct scsi_disk *sdkp)
 	kfree(buffer);
 }
 
+static int sd_try_extended_inquiry(struct scsi_device *sdp)
+{
+	/*
+	 * Although VPD inquiries can go to SCSI-2 type devices,
+	 * some USB ones crash on receiving them, and the pages
+	 * we currently ask for are for SPC-3 and beyond
+	 */
+	if (sdp->scsi_level > SCSI_SPC_2)
+		return 1;
+	return 0;
+}
+
 /**
  *	sd_revalidate_disk - called the first time a new disk is seen,
  *	performs disk spin up, read_capacity, etc.
@@ -1877,8 +1889,12 @@ static int sd_revalidate_disk(struct gendisk *disk)
 	 */
 	if (sdkp->media_present) {
 		sd_read_capacity(sdkp, buffer);
-		sd_read_block_limits(sdkp);
-		sd_read_block_characteristics(sdkp);
+
+		if (sd_try_extended_inquiry(sdp)) {
+			sd_read_block_limits(sdkp);
+			sd_read_block_characteristics(sdkp);
+		}
+
 		sd_read_write_protect_flag(sdkp, buffer);
 		sd_read_cache_type(sdkp, buffer);
 		sd_read_app_tag_own(sdkp, buffer);
-- 
GitLab


From 2b8d33f714477d1719f96459370037993520de84 Mon Sep 17 00:00:00 2001
From: "ling.ma@intel.com" <ling.ma@intel.com>
Date: Wed, 29 Jul 2009 11:31:18 +0800
Subject: [PATCH 0347/1153] drm/i915: Return disconnected for SDVO DVI when
 there's no digital EDID.

The patch fixed a bug on MP965-D.  When VGA is connected to a DVI-I connector,
it incorrectly shows sdvo dvi as connected.

Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: hand-resolved against previous commit and fixed up commit message]
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_sdvo.c | 27 +++++++++++++++++++++------
 1 file changed, 21 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c
index b68746f0380..5371d933255 100644
--- a/drivers/gpu/drm/i915/intel_sdvo.c
+++ b/drivers/gpu/drm/i915/intel_sdvo.c
@@ -31,6 +31,7 @@
 #include "drm.h"
 #include "drm_crtc.h"
 #include "intel_drv.h"
+#include "drm_edid.h"
 #include "i915_drm.h"
 #include "i915_drv.h"
 #include "intel_sdvo_regs.h"
@@ -1477,20 +1478,35 @@ intel_sdvo_multifunc_encoder(struct intel_output *intel_output)
 	return (caps > 1);
 }
 
-static void
-intel_sdvo_hdmi_sink_detect(struct drm_connector *connector)
+enum drm_connector_status
+intel_sdvo_hdmi_sink_detect(struct drm_connector *connector, u16 response)
 {
 	struct intel_output *intel_output = to_intel_output(connector);
 	struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv;
+	enum drm_connector_status status = connector_status_connected;
 	struct edid *edid = NULL;
 
 	edid = drm_get_edid(&intel_output->base,
 			    intel_output->ddc_bus);
 	if (edid != NULL) {
-		sdvo_priv->is_hdmi = drm_detect_hdmi_monitor(edid);
+		/* Don't report the output as connected if it's a DVI-I
+		 * connector with a non-digital EDID coming out.
+		 */
+		if (response & (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1)) {
+			if (edid->input & DRM_EDID_INPUT_DIGITAL)
+				sdvo_priv->is_hdmi =
+					drm_detect_hdmi_monitor(edid);
+			else
+				status = connector_status_disconnected;
+		}
+
 		kfree(edid);
 		intel_output->base.display_info.raw_edid = NULL;
-	}
+
+	} else if (response & (SDVO_OUTPUT_TMDS0 | SDVO_OUTPUT_TMDS1))
+		status = connector_status_disconnected;
+
+	return status;
 }
 
 static enum drm_connector_status intel_sdvo_detect(struct drm_connector *connector)
@@ -1518,8 +1534,7 @@ static enum drm_connector_status intel_sdvo_detect(struct drm_connector *connect
 			return connector_status_unknown;
 		sdvo_priv->attached_output = response;
 	}
-	intel_sdvo_hdmi_sink_detect(connector);
-	return connector_status_connected;
+	return intel_sdvo_hdmi_sink_detect(connector, response);
 }
 
 static void intel_sdvo_get_ddc_modes(struct drm_connector *connector)
-- 
GitLab


From 0c2e39525b3b53a97a0202c5f35058147e53977e Mon Sep 17 00:00:00 2001
From: "ling.ma@intel.com" <ling.ma@intel.com>
Date: Fri, 17 Jul 2009 11:44:30 +0800
Subject: [PATCH 0348/1153] drm/i915: Add support for dual-channel LVDS on 8xx.

This corresponds to a fix to UMS back in 2007.  Fixes fd.o bug #20115.

Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_display.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 1da7b0b9ed3..d6fce213341 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -90,7 +90,7 @@ struct intel_limit {
 #define I8XX_P2_SLOW		      4
 #define I8XX_P2_FAST		      2
 #define I8XX_P2_LVDS_SLOW	      14
-#define I8XX_P2_LVDS_FAST	      14 /* No fast option */
+#define I8XX_P2_LVDS_FAST	      7
 #define I8XX_P2_SLOW_LIMIT	 165000
 
 #define I9XX_DOT_MIN		  20000
-- 
GitLab


From ca7daea612b480ecf0fc5bd1630b88447fe73fc5 Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Thu, 30 Jul 2009 04:38:19 +0000
Subject: [PATCH 0349/1153] net/netlabel: Add kmalloc NULL tests

The test on map4 should be a test on map6.

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@

x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
    when != x != NULL
    when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/netlabel/netlabel_kapi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/netlabel/netlabel_kapi.c b/net/netlabel/netlabel_kapi.c
index b0e582f2d37..16e6c4378ff 100644
--- a/net/netlabel/netlabel_kapi.c
+++ b/net/netlabel/netlabel_kapi.c
@@ -151,7 +151,7 @@ int netlbl_cfg_unlbl_map_add(const char *domain,
 			addr6 = addr;
 			mask6 = mask;
 			map6 = kzalloc(sizeof(*map6), GFP_ATOMIC);
-			if (map4 == NULL)
+			if (map6 == NULL)
 				goto cfg_unlbl_map_add_failure;
 			map6->type = NETLBL_NLTYPE_UNLABELED;
 			ipv6_addr_copy(&map6->list.addr, addr6);
-- 
GitLab


From a541f8401d8e9113a89ee902cb8d8e412d6d3569 Mon Sep 17 00:00:00 2001
From: Michael Chan <mchan@broadcom.com>
Date: Wed, 29 Jul 2009 08:49:52 +0000
Subject: [PATCH 0350/1153] iscsi: Use GFP_ATOMIC in iscsi_offload_mesg().

Changing to GFP_ATOMIC because the only caller in cnic/bnx2i may
be calling this function while holding spin_lock.

This problem was discovered by Mike Christie.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/scsi/scsi_transport_iscsi.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/scsi_transport_iscsi.c b/drivers/scsi/scsi_transport_iscsi.c
index 783e33c65eb..b47240ca4b1 100644
--- a/drivers/scsi/scsi_transport_iscsi.c
+++ b/drivers/scsi/scsi_transport_iscsi.c
@@ -990,7 +990,7 @@ int iscsi_offload_mesg(struct Scsi_Host *shost,
 	struct iscsi_uevent *ev;
 	int len = NLMSG_SPACE(sizeof(*ev) + data_size);
 
-	skb = alloc_skb(len, GFP_NOIO);
+	skb = alloc_skb(len, GFP_ATOMIC);
 	if (!skb) {
 		printk(KERN_ERR "can not deliver iscsi offload message:OOM\n");
 		return -ENOMEM;
@@ -1012,7 +1012,7 @@ int iscsi_offload_mesg(struct Scsi_Host *shost,
 
 	memcpy((char *)ev + sizeof(*ev), data, data_size);
 
-	return iscsi_multicast_skb(skb, ISCSI_NL_GRP_UIP, GFP_NOIO);
+	return iscsi_multicast_skb(skb, ISCSI_NL_GRP_UIP, GFP_ATOMIC);
 }
 EXPORT_SYMBOL_GPL(iscsi_offload_mesg);
 
-- 
GitLab


From e9956fae7dbce6ac770e7a00436c496ddbbd3215 Mon Sep 17 00:00:00 2001
From: Tao Ma <tao.ma@oracle.com>
Date: Thu, 30 Jul 2009 16:07:10 +0800
Subject: [PATCH 0351/1153] ocfs2/quota: Release lock for error in
 ocfs2_quota_write.

ocfs2_quota_write needs to release the lock if it fails to
read quota block. So use "goto out" instead of "return err".

Signed-off-by: Tao Ma <tao.ma@oracle.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/quota_global.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c
index cc8785cf8f6..d604a6aa0a2 100644
--- a/fs/ocfs2/quota_global.c
+++ b/fs/ocfs2/quota_global.c
@@ -238,7 +238,7 @@ ssize_t ocfs2_quota_write(struct super_block *sb, int type,
 	}
 	if (err) {
 		mlog_errno(err);
-		return err;
+		goto out;
 	}
 	lock_buffer(bh);
 	if (new)
-- 
GitLab


From 2a8aaacda5097fa92a39948da1b4c6614b6e150e Mon Sep 17 00:00:00 2001
From: Tobias Klauser <tklauser@distanz.ch>
Date: Thu, 30 Jul 2009 13:10:50 -0700
Subject: [PATCH 0352/1153] docbook: fix printk of ip address

Use the %pI4 format string instead of %d.%d.%d.%d and NIPQUAD.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 Documentation/DocBook/kernel-hacking.tmpl | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/Documentation/DocBook/kernel-hacking.tmpl b/Documentation/DocBook/kernel-hacking.tmpl
index a50d6cd5857..992e67e6be7 100644
--- a/Documentation/DocBook/kernel-hacking.tmpl
+++ b/Documentation/DocBook/kernel-hacking.tmpl
@@ -449,8 +449,8 @@ printk(KERN_INFO "i = %u\n", i);
    </para>
 
    <programlisting>
-__u32 ipaddress;
-printk(KERN_INFO "my ip: %d.%d.%d.%d\n", NIPQUAD(ipaddress));
+__be32 ipaddress;
+printk(KERN_INFO "my ip: %pI4\n", &amp;ipaddress);
    </programlisting>
 
    <para>
-- 
GitLab


From 3d54015b750e5d5e950a1dcee2735387fd4b6e1a Mon Sep 17 00:00:00 2001
From: roel kluin <roel.kluin@gmail.com>
Date: Thu, 30 Jul 2009 00:26:32 +0000
Subject: [PATCH 0353/1153] 3c515: Write outside array bounds

if dev_alloc_skb() fails on the first iteration, a write to
cp->rx_ring[-1] occurs.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/3c515.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/3c515.c b/drivers/net/3c515.c
index 3e00fa8ea65..4a7c32895be 100644
--- a/drivers/net/3c515.c
+++ b/drivers/net/3c515.c
@@ -832,7 +832,9 @@ static int corkscrew_open(struct net_device *dev)
 			skb_reserve(skb, 2);	/* Align IP on 16 byte boundaries */
 			vp->rx_ring[i].addr = isa_virt_to_bus(skb->data);
 		}
-		vp->rx_ring[i - 1].next = isa_virt_to_bus(&vp->rx_ring[0]);	/* Wrap the ring. */
+		if (i != 0)
+			vp->rx_ring[i - 1].next =
+				isa_virt_to_bus(&vp->rx_ring[0]);	/* Wrap the ring. */
 		outl(isa_virt_to_bus(&vp->rx_ring[0]), ioaddr + UpListPtr);
 	}
 	if (vp->full_bus_master_tx) {	/* Boomerang bus master Tx. */
-- 
GitLab


From a3e8ee682003685b8b9c98c89340a42e48c3e813 Mon Sep 17 00:00:00 2001
From: roel kluin <roel.kluin@gmail.com>
Date: Wed, 29 Jul 2009 23:46:59 +0000
Subject: [PATCH 0354/1153] ipv4: ARP neigh procfs buffer overflow

If arp_format_neigh_entry() can be called with n->dev->addr_len == 0, then a
write to hbuffer[-1] occurs.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/ipv4/arp.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/net/ipv4/arp.c b/net/ipv4/arp.c
index c29d75d8f1b..090e9991ac2 100644
--- a/net/ipv4/arp.c
+++ b/net/ipv4/arp.c
@@ -1304,7 +1304,9 @@ static void arp_format_neigh_entry(struct seq_file *seq,
 		hbuffer[k++] = hex_asc_lo(n->ha[j]);
 		hbuffer[k++] = ':';
 	}
-	hbuffer[--k] = 0;
+	if (k != 0)
+		--k;
+	hbuffer[k] = 0;
 #if defined(CONFIG_AX25) || defined(CONFIG_AX25_MODULE)
 	}
 #endif
-- 
GitLab


From f0c5b35c6c93c89a9d8ccab19b0b4842f5dfddc5 Mon Sep 17 00:00:00 2001
From: roel kluin <roel.kluin@gmail.com>
Date: Wed, 29 Jul 2009 03:18:56 +0000
Subject: [PATCH 0355/1153] eexpress: Read buffer overflow

start_code is 69 words, but the code always writes a multiple of 16 words,
so the last 11 words written are outside the array.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/eexpress.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/eexpress.c b/drivers/net/eexpress.c
index 1686dca2874..1f016d66684 100644
--- a/drivers/net/eexpress.c
+++ b/drivers/net/eexpress.c
@@ -1474,13 +1474,13 @@ static void eexp_hw_init586(struct net_device *dev)
 	outw(0x0000, ioaddr + 0x800c);
 	outw(0x0000, ioaddr + 0x800e);
 
-	for (i = 0; i < (sizeof(start_code)); i+=32) {
+	for (i = 0; i < ARRAY_SIZE(start_code) * 2; i+=32) {
 		int j;
 		outw(i, ioaddr + SM_PTR);
-		for (j = 0; j < 16; j+=2)
+		for (j = 0; j < 16 && (i+j)/2 < ARRAY_SIZE(start_code); j+=2)
 			outw(start_code[(i+j)/2],
 			     ioaddr+0x4000+j);
-		for (j = 0; j < 16; j+=2)
+		for (j = 0; j < 16 && (i+j+16)/2 < ARRAY_SIZE(start_code); j+=2)
 			outw(start_code[(i+j+16)/2],
 			     ioaddr+0x8000+j);
 	}
-- 
GitLab


From daed953721850381673687c59f3a0df553eb6626 Mon Sep 17 00:00:00 2001
From: Frans Pop <elendil@planet.nl>
Date: Thu, 30 Jul 2009 17:16:05 -0400
Subject: [PATCH 0356/1153] hp-wmi: check that an input device exists in resume
 handler
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Some systems may not support input events, or registering the input
handler may have failed. So check that an input device exists before
trying to set the docking and tablet mode state during resume.

Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=13865

Reported-and-tested-by: Cédric Godin <cedric@belbone.be>
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/platform/x86/hp-wmi.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/platform/x86/hp-wmi.c b/drivers/platform/x86/hp-wmi.c
index ca508564a18..a2ad53e1587 100644
--- a/drivers/platform/x86/hp-wmi.c
+++ b/drivers/platform/x86/hp-wmi.c
@@ -520,11 +520,13 @@ static int hp_wmi_resume_handler(struct platform_device *device)
 	 * the input layer will only actually pass it on if the state
 	 * changed.
 	 */
-
-	input_report_switch(hp_wmi_input_dev, SW_DOCK, hp_wmi_dock_state());
-	input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE,
-			    hp_wmi_tablet_state());
-	input_sync(hp_wmi_input_dev);
+	if (hp_wmi_input_dev) {
+		input_report_switch(hp_wmi_input_dev, SW_DOCK,
+				    hp_wmi_dock_state());
+		input_report_switch(hp_wmi_input_dev, SW_TABLET_MODE,
+				    hp_wmi_tablet_state());
+		input_sync(hp_wmi_input_dev);
+	}
 
 	return 0;
 }
-- 
GitLab


From 72fc939789dbe7ca091b50b686d45ac0df15417a Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Tue, 28 Jul 2009 23:43:08 +0000
Subject: [PATCH 0357/1153] pppoe: fix /proc/net/pppoe

If a socket is hashed in last slot of pppoe hash table (PPPOE_HASH_SIZE-1)
we report it many times (up to filling seq buffer)
(Only the last socket of last slot)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/pppoe.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/pppoe.c b/drivers/net/pppoe.c
index f0031f1f97e..5f2090233d7 100644
--- a/drivers/net/pppoe.c
+++ b/drivers/net/pppoe.c
@@ -1063,6 +1063,7 @@ static void *pppoe_seq_next(struct seq_file *seq, void *v, loff_t *pos)
 	else {
 		int hash = hash_item(po->pppoe_pa.sid, po->pppoe_pa.remote);
 
+		po = NULL;
 		while (++hash < PPPOE_HASH_SIZE) {
 			po = pn->hash_table[hash];
 			if (po)
-- 
GitLab


From accff95c2500c7bce671c1f722de6f8810fe550d Mon Sep 17 00:00:00 2001
From: Jiajun Wu <b06378@freescale.com>
Date: Thu, 30 Jul 2009 14:20:42 -0700
Subject: [PATCH 0358/1153] gianfar: fix coalescing setup in ethtool support

Parameter order for using mk_ic_value(count, time) was reversed,
the patch fixes this.

Signed-off-by: Jiajun Wu <b06378@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/gianfar_ethtool.c | 10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)

diff --git a/drivers/net/gianfar_ethtool.c b/drivers/net/gianfar_ethtool.c
index dbf06e9313c..2234118eedb 100644
--- a/drivers/net/gianfar_ethtool.c
+++ b/drivers/net/gianfar_ethtool.c
@@ -366,9 +366,8 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals
 		return -EINVAL;
 	}
 
-	priv->rxic = mk_ic_value(
-		gfar_usecs2ticks(priv, cvals->rx_coalesce_usecs),
-		cvals->rx_max_coalesced_frames);
+	priv->rxic = mk_ic_value(cvals->rx_max_coalesced_frames,
+		gfar_usecs2ticks(priv, cvals->rx_coalesce_usecs));
 
 	/* Set up tx coalescing */
 	if ((cvals->tx_coalesce_usecs == 0) ||
@@ -390,9 +389,8 @@ static int gfar_scoalesce(struct net_device *dev, struct ethtool_coalesce *cvals
 		return -EINVAL;
 	}
 
-	priv->txic = mk_ic_value(
-		gfar_usecs2ticks(priv, cvals->tx_coalesce_usecs),
-		cvals->tx_max_coalesced_frames);
+	priv->txic = mk_ic_value(cvals->tx_max_coalesced_frames,
+		gfar_usecs2ticks(priv, cvals->tx_coalesce_usecs));
 
 	gfar_write(&priv->regs->rxic, 0);
 	if (priv->rxcoalescing)
-- 
GitLab


From 165f5f64199f972a21f21effc125d89ed2488e58 Mon Sep 17 00:00:00 2001
From: Peter Korsgaard <jacmet@sunsite.dk>
Date: Wed, 1 Jul 2009 17:47:08 +0200
Subject: [PATCH 0359/1153] ARM: S3C: PWM fix for low duty cycle

The pwm hardware only checks the compare register after a decrement,
so the pin never toggles if tcmp = tcnt.

This happens when a very low duty cycle is requested. Fix it by always
ensuring that tcmp < tcnt.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 arch/arm/plat-s3c24xx/pwm.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/plat-s3c24xx/pwm.c b/arch/arm/plat-s3c24xx/pwm.c
index 0120b760315..82a6d4de02a 100644
--- a/arch/arm/plat-s3c24xx/pwm.c
+++ b/arch/arm/plat-s3c24xx/pwm.c
@@ -246,6 +246,10 @@ int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns)
 
 	tcmp = duty_ns / tin_ns;
 	tcmp = tcnt - tcmp;
+	/* the pwm hw only checks the compare register after a decrement,
+	   so the pin never toggles if tcmp = tcnt */
+	if (tcmp == tcnt)
+		tcmp--;
 
 	pwm_dbg(pwm, "tin_ns=%lu, tcmp=%ld/%lu\n", tin_ns, tcmp, tcnt);
 
-- 
GitLab


From 8fe70a5f7167e02bbc18086970f0e92a5e55b80d Mon Sep 17 00:00:00 2001
From: Ramax Lo <ramaxlo@gmail.com>
Date: Thu, 9 Jul 2009 16:28:33 +0800
Subject: [PATCH 0360/1153] ARM: S3C24XX: serial: Fix section mismatch warnings

During kernel build process, the following warning was found:

WARNING: drivers/serial/built-in.o(.data+0x304): Section mismatch in reference from
the variable s3c2440_serial_drv to the function .devexit.text:s3c24xx_serial_remove()
The variable s3c2440_serial_drv references the function __devexit s3c24xx_serial_remove()
If the reference is valid then annotate the variable with
__exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

The same warning happened for s3c241x platform. We rename variables to avoid
these warnings. These changes also apply to s3c2400 & s3c24a0 for consistency.

Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/serial/s3c2400.c | 8 ++++----
 drivers/serial/s3c2410.c | 8 ++++----
 drivers/serial/s3c2412.c | 8 ++++----
 drivers/serial/s3c2440.c | 8 ++++----
 drivers/serial/s3c24a0.c | 8 ++++----
 5 files changed, 20 insertions(+), 20 deletions(-)

diff --git a/drivers/serial/s3c2400.c b/drivers/serial/s3c2400.c
index fb00ed5296e..fed1a9a1ffb 100644
--- a/drivers/serial/s3c2400.c
+++ b/drivers/serial/s3c2400.c
@@ -76,7 +76,7 @@ static int s3c2400_serial_probe(struct platform_device *dev)
 	return s3c24xx_serial_probe(dev, &s3c2400_uart_inf);
 }
 
-static struct platform_driver s3c2400_serial_drv = {
+static struct platform_driver s3c2400_serial_driver = {
 	.probe		= s3c2400_serial_probe,
 	.remove		= __devexit_p(s3c24xx_serial_remove),
 	.driver		= {
@@ -85,16 +85,16 @@ static struct platform_driver s3c2400_serial_drv = {
 	},
 };
 
-s3c24xx_console_init(&s3c2400_serial_drv, &s3c2400_uart_inf);
+s3c24xx_console_init(&s3c2400_serial_driver, &s3c2400_uart_inf);
 
 static inline int s3c2400_serial_init(void)
 {
-	return s3c24xx_serial_init(&s3c2400_serial_drv, &s3c2400_uart_inf);
+	return s3c24xx_serial_init(&s3c2400_serial_driver, &s3c2400_uart_inf);
 }
 
 static inline void s3c2400_serial_exit(void)
 {
-	platform_driver_unregister(&s3c2400_serial_drv);
+	platform_driver_unregister(&s3c2400_serial_driver);
 }
 
 module_init(s3c2400_serial_init);
diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c
index b5d7cbcba2a..c99f0821cae 100644
--- a/drivers/serial/s3c2410.c
+++ b/drivers/serial/s3c2410.c
@@ -88,7 +88,7 @@ static int s3c2410_serial_probe(struct platform_device *dev)
 	return s3c24xx_serial_probe(dev, &s3c2410_uart_inf);
 }
 
-static struct platform_driver s3c2410_serial_drv = {
+static struct platform_driver s3c2410_serial_driver = {
 	.probe		= s3c2410_serial_probe,
 	.remove		= __devexit_p(s3c24xx_serial_remove),
 	.driver		= {
@@ -97,16 +97,16 @@ static struct platform_driver s3c2410_serial_drv = {
 	},
 };
 
-s3c24xx_console_init(&s3c2410_serial_drv, &s3c2410_uart_inf);
+s3c24xx_console_init(&s3c2410_serial_driver, &s3c2410_uart_inf);
 
 static int __init s3c2410_serial_init(void)
 {
-	return s3c24xx_serial_init(&s3c2410_serial_drv, &s3c2410_uart_inf);
+	return s3c24xx_serial_init(&s3c2410_serial_driver, &s3c2410_uart_inf);
 }
 
 static void __exit s3c2410_serial_exit(void)
 {
-	platform_driver_unregister(&s3c2410_serial_drv);
+	platform_driver_unregister(&s3c2410_serial_driver);
 }
 
 module_init(s3c2410_serial_init);
diff --git a/drivers/serial/s3c2412.c b/drivers/serial/s3c2412.c
index 11dcb90bdfe..6e057d8809d 100644
--- a/drivers/serial/s3c2412.c
+++ b/drivers/serial/s3c2412.c
@@ -121,7 +121,7 @@ static int s3c2412_serial_probe(struct platform_device *dev)
 	return s3c24xx_serial_probe(dev, &s3c2412_uart_inf);
 }
 
-static struct platform_driver s3c2412_serial_drv = {
+static struct platform_driver s3c2412_serial_driver = {
 	.probe		= s3c2412_serial_probe,
 	.remove		= __devexit_p(s3c24xx_serial_remove),
 	.driver		= {
@@ -130,16 +130,16 @@ static struct platform_driver s3c2412_serial_drv = {
 	},
 };
 
-s3c24xx_console_init(&s3c2412_serial_drv, &s3c2412_uart_inf);
+s3c24xx_console_init(&s3c2412_serial_driver, &s3c2412_uart_inf);
 
 static inline int s3c2412_serial_init(void)
 {
-	return s3c24xx_serial_init(&s3c2412_serial_drv, &s3c2412_uart_inf);
+	return s3c24xx_serial_init(&s3c2412_serial_driver, &s3c2412_uart_inf);
 }
 
 static inline void s3c2412_serial_exit(void)
 {
-	platform_driver_unregister(&s3c2412_serial_drv);
+	platform_driver_unregister(&s3c2412_serial_driver);
 }
 
 module_init(s3c2412_serial_init);
diff --git a/drivers/serial/s3c2440.c b/drivers/serial/s3c2440.c
index 06c5b0cc47a..69ff5d340f0 100644
--- a/drivers/serial/s3c2440.c
+++ b/drivers/serial/s3c2440.c
@@ -151,7 +151,7 @@ static int s3c2440_serial_probe(struct platform_device *dev)
 	return s3c24xx_serial_probe(dev, &s3c2440_uart_inf);
 }
 
-static struct platform_driver s3c2440_serial_drv = {
+static struct platform_driver s3c2440_serial_driver = {
 	.probe		= s3c2440_serial_probe,
 	.remove		= __devexit_p(s3c24xx_serial_remove),
 	.driver		= {
@@ -160,16 +160,16 @@ static struct platform_driver s3c2440_serial_drv = {
 	},
 };
 
-s3c24xx_console_init(&s3c2440_serial_drv, &s3c2440_uart_inf);
+s3c24xx_console_init(&s3c2440_serial_driver, &s3c2440_uart_inf);
 
 static int __init s3c2440_serial_init(void)
 {
-	return s3c24xx_serial_init(&s3c2440_serial_drv, &s3c2440_uart_inf);
+	return s3c24xx_serial_init(&s3c2440_serial_driver, &s3c2440_uart_inf);
 }
 
 static void __exit s3c2440_serial_exit(void)
 {
-	platform_driver_unregister(&s3c2440_serial_drv);
+	platform_driver_unregister(&s3c2440_serial_driver);
 }
 
 module_init(s3c2440_serial_init);
diff --git a/drivers/serial/s3c24a0.c b/drivers/serial/s3c24a0.c
index 786a067d62a..26c49e18bdd 100644
--- a/drivers/serial/s3c24a0.c
+++ b/drivers/serial/s3c24a0.c
@@ -92,7 +92,7 @@ static int s3c24a0_serial_probe(struct platform_device *dev)
 	return s3c24xx_serial_probe(dev, &s3c24a0_uart_inf);
 }
 
-static struct platform_driver s3c24a0_serial_drv = {
+static struct platform_driver s3c24a0_serial_driver = {
 	.probe		= s3c24a0_serial_probe,
 	.remove		= __devexit_p(s3c24xx_serial_remove),
 	.driver		= {
@@ -101,16 +101,16 @@ static struct platform_driver s3c24a0_serial_drv = {
 	},
 };
 
-s3c24xx_console_init(&s3c24a0_serial_drv, &s3c24a0_uart_inf);
+s3c24xx_console_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf);
 
 static int __init s3c24a0_serial_init(void)
 {
-	return s3c24xx_serial_init(&s3c24a0_serial_drv, &s3c24a0_uart_inf);
+	return s3c24xx_serial_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf);
 }
 
 static void __exit s3c24a0_serial_exit(void)
 {
-	platform_driver_unregister(&s3c24a0_serial_drv);
+	platform_driver_unregister(&s3c24a0_serial_driver);
 }
 
 module_init(s3c24a0_serial_init);
-- 
GitLab


From 909db80297ba65699a77d877f7bf618ba960f6fc Mon Sep 17 00:00:00 2001
From: Ramax Lo <ramaxlo@gmail.com>
Date: Fri, 10 Jul 2009 19:30:56 +0800
Subject: [PATCH 0361/1153] ARM: S3C64XX: serial: Fix section mismatch warning

Rename the structure to avoid the following warning:

WARNING: vmlinux.o(.data+0x11ef4): Section mismatch in reference from the variable
s3c6400_serial_drv to the function .devexit.text:s3c24xx_serial_remove()
The variable s3c6400_serial_drv references
the function __devexit s3c24xx_serial_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/serial/s3c6400.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/serial/s3c6400.c b/drivers/serial/s3c6400.c
index 48f1a3781f0..4be92ab5005 100644
--- a/drivers/serial/s3c6400.c
+++ b/drivers/serial/s3c6400.c
@@ -122,7 +122,7 @@ static int s3c6400_serial_probe(struct platform_device *dev)
 	return s3c24xx_serial_probe(dev, &s3c6400_uart_inf);
 }
 
-static struct platform_driver s3c6400_serial_drv = {
+static struct platform_driver s3c6400_serial_driver = {
 	.probe		= s3c6400_serial_probe,
 	.remove		= __devexit_p(s3c24xx_serial_remove),
 	.driver		= {
@@ -131,16 +131,16 @@ static struct platform_driver s3c6400_serial_drv = {
 	},
 };
 
-s3c24xx_console_init(&s3c6400_serial_drv, &s3c6400_uart_inf);
+s3c24xx_console_init(&s3c6400_serial_driver, &s3c6400_uart_inf);
 
 static int __init s3c6400_serial_init(void)
 {
-	return s3c24xx_serial_init(&s3c6400_serial_drv, &s3c6400_uart_inf);
+	return s3c24xx_serial_init(&s3c6400_serial_driver, &s3c6400_uart_inf);
 }
 
 static void __exit s3c6400_serial_exit(void)
 {
-	platform_driver_unregister(&s3c6400_serial_drv);
+	platform_driver_unregister(&s3c6400_serial_driver);
 }
 
 module_init(s3c6400_serial_init);
-- 
GitLab


From 90a09c9cf78344d18e2438c3b87363b949629fa3 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Thu, 30 Jul 2009 16:40:37 -0700
Subject: [PATCH 0362/1153] Alan doesn't want to maintain tty code any more

Not that anybody can blame him.  It's a morass.  But hey, it's way
better than it _used_ to be, though, so thanks for all the fish.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 66a3865da88..79471ba4981 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -155,10 +155,9 @@ S:	Maintained
 F:	drivers/net/r8169.c
 
 8250/16?50 (AND CLONE UARTS) SERIAL DRIVER
-M:	Alan Cox <alan@lxorguk.ukuu.org.uk>
 L:	linux-serial@vger.kernel.org
 W:	http://serial.sourceforge.net
-S:	Odd Fixes
+S:	Orphan
 F:	drivers/serial/8250*
 F:	include/linux/serial_8250.h
 
@@ -4997,9 +4996,7 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial.git
 S:	Maintained
 
 TTY LAYER
-M:	Alan Cox <alan@lxorguk.ukuu.org.uk>
-S:	Maintained
-T:	stgit http://zeniv.linux.org.uk/~alan/ttydev/
+S:	Orphan
 F:	drivers/char/tty_*
 F:	drivers/serial/serial_core.c
 F:	include/linux/serial_core.h
-- 
GitLab


From ec30c5f3a18722f8fcf8c83146a10b03ac4d9ff1 Mon Sep 17 00:00:00 2001
From: Masami Hiramatsu <mhiramat@redhat.com>
Date: Tue, 28 Jul 2009 19:47:23 -0400
Subject: [PATCH 0363/1153] kprobes: Use kernel_text_address() for checking
 probe address

Use kernel_text_address() for checking probe address instead of
__kernel_text_address(), because __kernel_text_address() returns true
for init functions even after relaseing those functions.

That will hit a BUG() in text_poke().

Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/kprobes.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/kprobes.c b/kernel/kprobes.c
index 16b5739c516..0540948e29a 100644
--- a/kernel/kprobes.c
+++ b/kernel/kprobes.c
@@ -694,7 +694,7 @@ int __kprobes register_kprobe(struct kprobe *p)
 	p->addr = addr;
 
 	preempt_disable();
-	if (!__kernel_text_address((unsigned long) p->addr) ||
+	if (!kernel_text_address((unsigned long) p->addr) ||
 	    in_kprobes_functions((unsigned long) p->addr)) {
 		preempt_enable();
 		return -EINVAL;
-- 
GitLab


From bdc6340f4eb68295b1e7c0ade2356b56dca93d93 Mon Sep 17 00:00:00 2001
From: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Date: Thu, 30 Jul 2009 14:43:19 -0700
Subject: [PATCH 0364/1153] x86, pat: Fix set_memory_wc related corruption

Changeset 3869c4aa18835c8c61b44bd0f3ace36e9d3b5bd0
that went in after 2.6.30-rc1 was a seemingly small change to _set_memory_wc()
to make it complaint with SDM requirements. But, introduced a nasty bug, which
can result in crash and/or strange corruptions when set_memory_wc is used.
One such crash reported here
http://lkml.org/lkml/2009/7/30/94

Actually, that changeset introduced two bugs.
* change_page_attr_set() takes &addr as first argument and can the addr value
  might have changed on return, even for single page change_page_attr_set()
  call. That will make the second change_page_attr_set() in this routine
  operate on unrelated addr, that can eventually cause strange corruptions
  and bad page state crash.
* The second change_page_attr_set() call, before setting _PAGE_CACHE_WC, should
  clear the earlier _PAGE_CACHE_UC_MINUS, as otherwise cache attribute will not
  be WC (will be UC instead).

The patch below fixes both these problems. Sending a single patch to fix both
the problems, as the change is to the same line of code. The change to have a
addr_copy is not very clean. But, it is simpler than making more changes
through various routines in pageattr.c.

A huge thanks to Jerome for reporting this problem and providing a simple test
case that helped us root cause the problem.

Reported-by: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20090730214319.GA1889@linux-os.sc.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
---
 arch/x86/mm/pageattr.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/arch/x86/mm/pageattr.c b/arch/x86/mm/pageattr.c
index 1b734d7a896..895d90e1a81 100644
--- a/arch/x86/mm/pageattr.c
+++ b/arch/x86/mm/pageattr.c
@@ -997,12 +997,15 @@ EXPORT_SYMBOL(set_memory_array_uc);
 int _set_memory_wc(unsigned long addr, int numpages)
 {
 	int ret;
+	unsigned long addr_copy = addr;
+
 	ret = change_page_attr_set(&addr, numpages,
 				    __pgprot(_PAGE_CACHE_UC_MINUS), 0);
-
 	if (!ret) {
-		ret = change_page_attr_set(&addr, numpages,
-				    __pgprot(_PAGE_CACHE_WC), 0);
+		ret = change_page_attr_set_clr(&addr_copy, numpages,
+					       __pgprot(_PAGE_CACHE_WC),
+					       __pgprot(_PAGE_CACHE_MASK),
+					       0, 0, NULL);
 	}
 	return ret;
 }
-- 
GitLab


From 8f9a71673d9f397a365f4d18c307e91141b8fe92 Mon Sep 17 00:00:00 2001
From: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Date: Thu, 30 Jul 2009 12:25:09 +0000
Subject: [PATCH 0365/1153] ixgbe: Fix netpoll to be properly multiqueue aware

Our ndo_poll_controller callback is broken for anything but non-multiqueue
setups.  This fixes that issue.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ixgbe/ixgbe_main.c | 13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index 200454f30f6..60c4a8bf7d3 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -5360,12 +5360,19 @@ static int ixgbe_del_sanmac_netdev(struct net_device *dev)
 static void ixgbe_netpoll(struct net_device *netdev)
 {
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
+	int i;
 
-	disable_irq(adapter->pdev->irq);
 	adapter->flags |= IXGBE_FLAG_IN_NETPOLL;
-	ixgbe_intr(adapter->pdev->irq, netdev);
+	if (adapter->flags & IXGBE_FLAG_MSIX_ENABLED) {
+		int num_q_vectors = adapter->num_msix_vectors - NON_Q_VECTORS;
+		for (i = 0; i < num_q_vectors; i++) {
+			struct ixgbe_q_vector *q_vector = adapter->q_vector[i];
+			ixgbe_msix_clean_many(0, q_vector);
+		}
+	} else {
+		ixgbe_intr(adapter->pdev->irq, netdev);
+	}
 	adapter->flags &= ~IXGBE_FLAG_IN_NETPOLL;
-	enable_irq(adapter->pdev->irq);
 }
 #endif
 
-- 
GitLab


From 0c19d6af9253f19b41821c29b9c49c2214f19425 Mon Sep 17 00:00:00 2001
From: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Date: Thu, 30 Jul 2009 12:25:28 +0000
Subject: [PATCH 0366/1153] ixgbe: Fix usage of second flags bitmap when using
 LRO/RSC

A second set of feature flag bits was added, and the hardware RSC engine
flags were moved there.  However, the code itself didn't make the move
completely to use the new bitmap.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ixgbe/ixgbe_ethtool.c |  6 +++---
 drivers/net/ixgbe/ixgbe_main.c    | 12 ++++++------
 2 files changed, 9 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c
index 2a978008fd6..7ddb50c03f0 100644
--- a/drivers/net/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ixgbe/ixgbe_ethtool.c
@@ -1999,13 +1999,13 @@ static int ixgbe_set_flags(struct net_device *netdev, u32 data)
 
 	ethtool_op_set_flags(netdev, data);
 
-	if (!(adapter->flags & IXGBE_FLAG2_RSC_CAPABLE))
+	if (!(adapter->flags2 & IXGBE_FLAG2_RSC_CAPABLE))
 		return 0;
 
 	/* if state changes we need to update adapter->flags and reset */
 	if ((!!(data & ETH_FLAG_LRO)) != 
-	    (!!(adapter->flags & IXGBE_FLAG2_RSC_ENABLED))) {
-		adapter->flags ^= IXGBE_FLAG2_RSC_ENABLED;
+	    (!!(adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED))) {
+		adapter->flags2 ^= IXGBE_FLAG2_RSC_ENABLED;
 		if (netif_running(netdev))
 			ixgbe_reinit_locked(adapter);
 		else
diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index 60c4a8bf7d3..110c65ab5cb 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -780,7 +780,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector,
 		prefetch(next_rxd);
 		cleaned_count++;
 
-		if (adapter->flags & IXGBE_FLAG2_RSC_CAPABLE)
+		if (adapter->flags2 & IXGBE_FLAG2_RSC_CAPABLE)
 			rsc_count = ixgbe_get_rsc_count(rx_desc);
 
 		if (rsc_count) {
@@ -2036,7 +2036,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 			IXGBE_WRITE_REG(hw, IXGBE_PSRTYPE(0), psrtype);
 		}
 	} else {
-		if (!(adapter->flags & IXGBE_FLAG2_RSC_ENABLED) &&
+		if (!(adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) &&
 		    (netdev->mtu <= ETH_DATA_LEN))
 			rx_buf_len = MAXIMUM_ETHERNET_VLAN_SIZE;
 		else
@@ -2165,7 +2165,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 		IXGBE_WRITE_REG(hw, IXGBE_RDRXCTL, rdrxctl);
 	}
 
-	if (adapter->flags & IXGBE_FLAG2_RSC_ENABLED) {
+	if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) {
 		/* Enable 82599 HW-RSC */
 		for (i = 0; i < adapter->num_rx_queues; i++) {
 			j = adapter->rx_ring[i].reg_idx;
@@ -3812,8 +3812,8 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter)
 		adapter->max_msix_q_vectors = MAX_MSIX_Q_VECTORS_82598;
 	} else if (hw->mac.type == ixgbe_mac_82599EB) {
 		adapter->max_msix_q_vectors = MAX_MSIX_Q_VECTORS_82599;
-		adapter->flags |= IXGBE_FLAG2_RSC_CAPABLE;
-		adapter->flags |= IXGBE_FLAG2_RSC_ENABLED;
+		adapter->flags2 |= IXGBE_FLAG2_RSC_CAPABLE;
+		adapter->flags2 |= IXGBE_FLAG2_RSC_ENABLED;
 		adapter->flags |= IXGBE_FLAG_FDIR_HASH_CAPABLE;
 		adapter->ring_feature[RING_F_FDIR].indices =
 		                                         IXGBE_MAX_FDIR_INDICES;
@@ -5618,7 +5618,7 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
 	if (pci_using_dac)
 		netdev->features |= NETIF_F_HIGHDMA;
 
-	if (adapter->flags & IXGBE_FLAG2_RSC_ENABLED)
+	if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED)
 		netdev->features |= NETIF_F_LRO;
 
 	/* make sure the EEPROM is good */
-- 
GitLab


From 0a924578bc4a2823a95c151f56975c71f5c156bb Mon Sep 17 00:00:00 2001
From: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Date: Thu, 30 Jul 2009 12:26:00 +0000
Subject: [PATCH 0367/1153] ixgbe: Fix RSC completion delay causing Rx
 interrupts to stop

When a user disables interrupt throttling with ethtool on 82599 devices,
the interrupt timer may not be re-enabled if hardware RSC is running.  The
RSC completions in hardware don't complete before the next ITR event tries
to fire, so the ITR timer never gets re-armed.  This patch increases the
amount of time between interrupts when throttling is disabled (rx-usecs =
0) when the hardware RSC deature is enabled.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ixgbe/ixgbe.h         | 2 ++
 drivers/net/ixgbe/ixgbe_ethtool.c | 5 ++++-
 2 files changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h
index 1b12c7ba275..e11d83d5852 100644
--- a/drivers/net/ixgbe/ixgbe.h
+++ b/drivers/net/ixgbe/ixgbe.h
@@ -96,6 +96,8 @@
 #define IXGBE_TX_FLAGS_VLAN_PRIO_MASK   0x0000e000
 #define IXGBE_TX_FLAGS_VLAN_SHIFT	16
 
+#define IXGBE_MAX_RSC_INT_RATE          162760
+
 /* wrapper around a pointer to a socket buffer,
  * so a DMA handle can be stored along with the buffer */
 struct ixgbe_tx_buffer {
diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c
index 7ddb50c03f0..79144e950a3 100644
--- a/drivers/net/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ixgbe/ixgbe_ethtool.c
@@ -1975,7 +1975,10 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
 		 * any other value means disable eitr, which is best
 		 * served by setting the interrupt rate very high
 		 */
-		adapter->eitr_param = IXGBE_MAX_INT_RATE;
+		if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED)
+			adapter->eitr_param = IXGBE_MAX_RSC_INT_RATE;
+		else
+			adapter->eitr_param = IXGBE_MAX_INT_RATE;
 		adapter->itr_setting = 0;
 	}
 
-- 
GitLab


From 95fc17aac45300f45968aacd97a536ddd8db8101 Mon Sep 17 00:00:00 2001
From: Dan Williams <dan.j.williams@intel.com>
Date: Fri, 31 Jul 2009 12:39:15 +1000
Subject: [PATCH 0368/1153] md/raid6: release spare page at ->stop()

Add missing call to safe_put_page from stop() by unifying open coded
raid5_conf_t de-allocation under free_conf().

Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/raid5.c | 26 ++++++++++++--------------
 1 file changed, 12 insertions(+), 14 deletions(-)

diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index 37835538b58..39374230a46 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -4316,6 +4316,15 @@ raid5_size(mddev_t *mddev, sector_t sectors, int raid_disks)
 	return sectors * (raid_disks - conf->max_degraded);
 }
 
+static void free_conf(raid5_conf_t *conf)
+{
+	shrink_stripes(conf);
+	safe_put_page(conf->spare_page);
+	kfree(conf->disks);
+	kfree(conf->stripe_hashtbl);
+	kfree(conf);
+}
+
 static raid5_conf_t *setup_conf(mddev_t *mddev)
 {
 	raid5_conf_t *conf;
@@ -4447,11 +4456,7 @@ static raid5_conf_t *setup_conf(mddev_t *mddev)
 
  abort:
 	if (conf) {
-		shrink_stripes(conf);
-		safe_put_page(conf->spare_page);
-		kfree(conf->disks);
-		kfree(conf->stripe_hashtbl);
-		kfree(conf);
+		free_conf(conf);
 		return ERR_PTR(-EIO);
 	} else
 		return ERR_PTR(-ENOMEM);
@@ -4629,12 +4634,8 @@ abort:
 	md_unregister_thread(mddev->thread);
 	mddev->thread = NULL;
 	if (conf) {
-		shrink_stripes(conf);
 		print_raid5_conf(conf);
-		safe_put_page(conf->spare_page);
-		kfree(conf->disks);
-		kfree(conf->stripe_hashtbl);
-		kfree(conf);
+		free_conf(conf);
 	}
 	mddev->private = NULL;
 	printk(KERN_ALERT "raid5: failed to run raid set %s\n", mdname(mddev));
@@ -4649,13 +4650,10 @@ static int stop(mddev_t *mddev)
 
 	md_unregister_thread(mddev->thread);
 	mddev->thread = NULL;
-	shrink_stripes(conf);
-	kfree(conf->stripe_hashtbl);
 	mddev->queue->backing_dev_info.congested_fn = NULL;
 	blk_sync_queue(mddev->queue); /* the unplug fn references 'conf'*/
 	sysfs_remove_group(&mddev->kobj, &raid5_attrs_group);
-	kfree(conf->disks);
-	kfree(conf);
+	free_conf(conf);
 	mddev->private = NULL;
 	return 0;
 }
-- 
GitLab


From 97db39a1f6f69e906e98118392400de5217aa33a Mon Sep 17 00:00:00 2001
From: Eric Sandeen <sandeen@sandeen.net>
Date: Sun, 26 Jul 2009 21:52:01 -0500
Subject: [PATCH 0369/1153] xfs: reduce bmv_count in xfs_vn_fiemap

commit 6321e3ed2acf3ee9643cdd403e1c88605d7944ba caused
the full bmv_count's worth of getbmapx structures to get
allocated; telling it to do MAXEXTNUM was a bit insane,
resulting in ENOMEM every time.

Chop it down to something reasonable, the number of slots
in the caller's input buffer.  If this is too large the
caller may get ENOMEM but the reason should not be a
mystery, and they can try again with something smaller.

We add 1 to the value because in the normal getbmap
world, bmv_count includes the header and xfs_getbmap does:

        nex = bmv->bmv_count - 1;
        if (nex <= 0)
                return XFS_ERROR(EINVAL);

Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/linux-2.6/xfs_iops.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/fs/xfs/linux-2.6/xfs_iops.c b/fs/xfs/linux-2.6/xfs_iops.c
index 58973bb4603..8070b34cc28 100644
--- a/fs/xfs/linux-2.6/xfs_iops.c
+++ b/fs/xfs/linux-2.6/xfs_iops.c
@@ -680,8 +680,8 @@ xfs_vn_fiemap(
 	else
 		bm.bmv_length = BTOBB(length);
 
-	/* our formatter will tell xfs_getbmap when to stop. */
-	bm.bmv_count = MAXEXTNUM;
+	/* We add one because in getbmap world count includes the header */
+	bm.bmv_count = fieinfo->fi_extents_max + 1;
 	bm.bmv_iflags = BMV_IF_PREALLOC;
 	if (fieinfo->fi_flags & FIEMAP_FLAG_XATTR)
 		bm.bmv_iflags |= BMV_IF_ATTRFORK;
-- 
GitLab


From c8a4051c3731b6db224482218cfd535ab9393ff8 Mon Sep 17 00:00:00 2001
From: Eric Sandeen <sandeen@sandeen.net>
Date: Fri, 31 Jul 2009 00:02:17 -0500
Subject: [PATCH 0370/1153] xfs: bump up nr_to_write in xfs_vm_writepage

VM calculation for nr_to_write seems off.  Bump it way
up, this gets simple streaming writes zippy again.
To be reviewed again after Jens' writeback changes.

Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Cc: Chris Mason <chris.mason@oracle.com>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/linux-2.6/xfs_aops.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/fs/xfs/linux-2.6/xfs_aops.c b/fs/xfs/linux-2.6/xfs_aops.c
index 7ec89fc05b2..aecf2519db7 100644
--- a/fs/xfs/linux-2.6/xfs_aops.c
+++ b/fs/xfs/linux-2.6/xfs_aops.c
@@ -1268,6 +1268,14 @@ xfs_vm_writepage(
 	if (!page_has_buffers(page))
 		create_empty_buffers(page, 1 << inode->i_blkbits, 0);
 
+
+	/*
+	 *  VM calculation for nr_to_write seems off.  Bump it way
+	 *  up, this gets simple streaming writes zippy again.
+	 *  To be reviewed again after Jens' writeback changes.
+	 */
+	wbc->nr_to_write *= 4;
+
 	/*
 	 * Convert delayed allocate, unwritten or unmapped space
 	 * to real space and flush out to disk.
-- 
GitLab


From cbb4f2646d77b536ed2b1500ef6641083228ed8f Mon Sep 17 00:00:00 2001
From: Li Zefan <lizf@cn.fujitsu.com>
Date: Fri, 31 Jul 2009 08:55:48 +0200
Subject: [PATCH 0371/1153] io context: fix ref counting

Commit d9c7d394a8ebacb60097b192939ae9f15235225e
("block: prevent possible io_context->refcount overflow") mistakenly
changed atomic_inc(&ioc->nr_tasks) to atomic_long_inc(&ioc->refcount).

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 include/linux/iocontext.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/iocontext.h b/include/linux/iocontext.h
index dd05434fa45..4da4a75c3f1 100644
--- a/include/linux/iocontext.h
+++ b/include/linux/iocontext.h
@@ -92,7 +92,7 @@ static inline struct io_context *ioc_task_link(struct io_context *ioc)
 	 * a race).
 	 */
 	if (ioc && atomic_long_inc_not_zero(&ioc->refcount)) {
-		atomic_long_inc(&ioc->refcount);
+		atomic_inc(&ioc->nr_tasks);
 		return ioc;
 	}
 
-- 
GitLab


From aa563af763373a7e67a7b8fdb427d2a2fcbeab3b Mon Sep 17 00:00:00 2001
From: Takashi Iwai <tiwai@suse.de>
Date: Fri, 31 Jul 2009 10:05:11 +0200
Subject: [PATCH 0372/1153] ALSA: hda - Increase PCM stream name buf in
 patch_realtek.c

The name buf with size 16 is too short for some codec names, e.g.
truncated like "ALC861-VD Analo".  Now the size is doubled.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/patch_realtek.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index 8c8b273116f..b95df5d5dcc 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -275,13 +275,13 @@ struct alc_spec {
 						 */
 	unsigned int num_init_verbs;
 
-	char stream_name_analog[16];	/* analog PCM stream */
+	char stream_name_analog[32];	/* analog PCM stream */
 	struct hda_pcm_stream *stream_analog_playback;
 	struct hda_pcm_stream *stream_analog_capture;
 	struct hda_pcm_stream *stream_analog_alt_playback;
 	struct hda_pcm_stream *stream_analog_alt_capture;
 
-	char stream_name_digital[16];	/* digital PCM stream */
+	char stream_name_digital[32];	/* digital PCM stream */
 	struct hda_pcm_stream *stream_digital_playback;
 	struct hda_pcm_stream *stream_digital_capture;
 
-- 
GitLab


From f065fabc864f4c98857bf67caa2365e9f8545751 Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Fri, 31 Jul 2009 08:32:03 +0200
Subject: [PATCH 0373/1153] ALSA: sound/aoa: Add kmalloc NULL tests

Check that the result of kzalloc is not NULL before a dereference.

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@

x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
    when != x != NULL
    when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/aoa/core/gpio-pmf.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/sound/aoa/core/gpio-pmf.c b/sound/aoa/core/gpio-pmf.c
index 5ca2220eac7..1dd0c28d1fb 100644
--- a/sound/aoa/core/gpio-pmf.c
+++ b/sound/aoa/core/gpio-pmf.c
@@ -182,6 +182,10 @@ static int pmf_set_notify(struct gpio_runtime *rt,
 	if (!old && notify) {
 		irq_client = kzalloc(sizeof(struct pmf_irq_client),
 				     GFP_KERNEL);
+		if (!irq_client) {
+			err = -ENOMEM;
+			goto out_unlock;
+		}
 		irq_client->data = notif;
 		irq_client->handler = pmf_handle_notify_irq;
 		irq_client->owner = THIS_MODULE;
-- 
GitLab


From 6de7e356faf54aa75de5b624bbce28a5b776dfa8 Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Date: Thu, 18 Jun 2009 10:19:12 +0200
Subject: [PATCH 0374/1153] lib/scatterlist: add a flags to signalize mapping
 direction

sg_miter_start() is currently unaware of the direction of the copy
process (to or from the scatter list). It is important to know the
direction because the page has to be flushed in case the data written
is seen on a different mapping in user land on cache incoherent
architectures.

Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
---
 include/linux/scatterlist.h |  2 ++
 lib/scatterlist.c           | 16 ++++++++++++----
 2 files changed, 14 insertions(+), 4 deletions(-)

diff --git a/include/linux/scatterlist.h b/include/linux/scatterlist.h
index e5996984ddd..9aaf5bfdad1 100644
--- a/include/linux/scatterlist.h
+++ b/include/linux/scatterlist.h
@@ -242,6 +242,8 @@ size_t sg_copy_to_buffer(struct scatterlist *sgl, unsigned int nents,
  */
 
 #define SG_MITER_ATOMIC		(1 << 0)	 /* use kmap_atomic */
+#define SG_MITER_TO_SG		(1 << 1)	/* flush back to phys on unmap */
+#define SG_MITER_FROM_SG	(1 << 2)	/* nop */
 
 struct sg_mapping_iter {
 	/* the following three fields can be accessed directly */
diff --git a/lib/scatterlist.c b/lib/scatterlist.c
index a295e404e90..0d475d8167b 100644
--- a/lib/scatterlist.c
+++ b/lib/scatterlist.c
@@ -314,6 +314,7 @@ void sg_miter_start(struct sg_mapping_iter *miter, struct scatterlist *sgl,
 	miter->__sg = sgl;
 	miter->__nents = nents;
 	miter->__offset = 0;
+	WARN_ON(!(flags & (SG_MITER_TO_SG | SG_MITER_FROM_SG)));
 	miter->__flags = flags;
 }
 EXPORT_SYMBOL(sg_miter_start);
@@ -394,6 +395,9 @@ void sg_miter_stop(struct sg_mapping_iter *miter)
 	if (miter->addr) {
 		miter->__offset += miter->consumed;
 
+		if (miter->__flags & SG_MITER_TO_SG)
+			flush_kernel_dcache_page(miter->page);
+
 		if (miter->__flags & SG_MITER_ATOMIC) {
 			WARN_ON(!irqs_disabled());
 			kunmap_atomic(miter->addr, KM_BIO_SRC_IRQ);
@@ -426,8 +430,14 @@ static size_t sg_copy_buffer(struct scatterlist *sgl, unsigned int nents,
 	unsigned int offset = 0;
 	struct sg_mapping_iter miter;
 	unsigned long flags;
+	unsigned int sg_flags = SG_MITER_ATOMIC;
+
+	if (to_buffer)
+		sg_flags |= SG_MITER_FROM_SG;
+	else
+		sg_flags |= SG_MITER_TO_SG;
 
-	sg_miter_start(&miter, sgl, nents, SG_MITER_ATOMIC);
+	sg_miter_start(&miter, sgl, nents, sg_flags);
 
 	local_irq_save(flags);
 
@@ -438,10 +448,8 @@ static size_t sg_copy_buffer(struct scatterlist *sgl, unsigned int nents,
 
 		if (to_buffer)
 			memcpy(buf + offset, miter.addr, len);
-		else {
+		else
 			memcpy(miter.addr, buf + offset, len);
-			flush_kernel_dcache_page(miter.page);
-		}
 
 		offset += len;
 	}
-- 
GitLab


From da60a91d012bcb10bc5bcd86d585c4281742832c Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Date: Thu, 18 Jun 2009 09:33:32 +0200
Subject: [PATCH 0375/1153] sdhci: use SG_MITER_TO_SG/SG_MITER_FROM_SG

so the page will be flushed on unmap on ARCH which need it.

Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
---
 drivers/mmc/host/sdhci.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 62041c7e924..fc96f8cb9c0 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -773,8 +773,14 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data)
 	}
 
 	if (!(host->flags & SDHCI_REQ_USE_DMA)) {
-		sg_miter_start(&host->sg_miter,
-			data->sg, data->sg_len, SG_MITER_ATOMIC);
+		int flags;
+
+		flags = SG_MITER_ATOMIC;
+		if (host->data->flags & MMC_DATA_READ)
+			flags |= SG_MITER_TO_SG;
+		else
+			flags |= SG_MITER_FROM_SG;
+		sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
 		host->blocks = data->blocks;
 	}
 
-- 
GitLab


From 4b2a108cd0d34880fe9d932258ca5b2ccebcd05e Mon Sep 17 00:00:00 2001
From: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Date: Mon, 22 Jun 2009 09:18:05 +0200
Subject: [PATCH 0376/1153] cb710: use SG_MITER_TO_SG/SG_MITER_FROM_SG
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

the code allready uses flush_kernel_dcache_page(). This patch updates the
driver to the recent sg API changes which require that either SG_MITER_TO_SG
or SG_MITER_FROM_SG is set. SG_MITER_TO_SG calls flush_kernel_dcache_page()
in sg_mitter_stop()

Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
---
 drivers/misc/cb710/sgbuf2.c  |  4 ----
 drivers/mmc/host/cb710-mmc.c |  6 +++---
 include/linux/cb710.h        | 29 +++--------------------------
 3 files changed, 6 insertions(+), 33 deletions(-)

diff --git a/drivers/misc/cb710/sgbuf2.c b/drivers/misc/cb710/sgbuf2.c
index d38a7acdb6e..d019746551f 100644
--- a/drivers/misc/cb710/sgbuf2.c
+++ b/drivers/misc/cb710/sgbuf2.c
@@ -114,7 +114,6 @@ static void sg_dwiter_write_slow(struct sg_mapping_iter *miter, uint32_t data)
 		if (!left)
 			return;
 		addr += len;
-		flush_kernel_dcache_page(miter->page);
 	} while (sg_dwiter_next(miter));
 }
 
@@ -142,9 +141,6 @@ void cb710_sg_dwiter_write_next_block(struct sg_mapping_iter *miter, uint32_t da
 			return;
 	} else
 		sg_dwiter_write_slow(miter, data);
-
-	if (miter->length == miter->consumed)
-		flush_kernel_dcache_page(miter->page);
 }
 EXPORT_SYMBOL_GPL(cb710_sg_dwiter_write_next_block);
 
diff --git a/drivers/mmc/host/cb710-mmc.c b/drivers/mmc/host/cb710-mmc.c
index 11efefb1af5..4e72964a7b4 100644
--- a/drivers/mmc/host/cb710-mmc.c
+++ b/drivers/mmc/host/cb710-mmc.c
@@ -278,7 +278,7 @@ static int cb710_mmc_receive(struct cb710_slot *slot, struct mmc_data *data)
 	if (unlikely(data->blksz & 15 && (data->blocks != 1 || data->blksz != 8)))
 		return -EINVAL;
 
-	sg_miter_start(&miter, data->sg, data->sg_len, 0);
+	sg_miter_start(&miter, data->sg, data->sg_len, SG_MITER_TO_SG);
 
 	cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT,
 		15, CB710_MMC_C2_READ_PIO_SIZE_MASK);
@@ -307,7 +307,7 @@ static int cb710_mmc_receive(struct cb710_slot *slot, struct mmc_data *data)
 			goto out;
 	}
 out:
-	cb710_sg_miter_stop_writing(&miter);
+	sg_miter_stop(&miter);
 	return err;
 }
 
@@ -322,7 +322,7 @@ static int cb710_mmc_send(struct cb710_slot *slot, struct mmc_data *data)
 	if (unlikely(data->blocks > 1 && data->blksz & 15))
 		return -EINVAL;
 
-	sg_miter_start(&miter, data->sg, data->sg_len, 0);
+	sg_miter_start(&miter, data->sg, data->sg_len, SG_MITER_FROM_SG);
 
 	cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT,
 		0, CB710_MMC_C2_READ_PIO_SIZE_MASK);
diff --git a/include/linux/cb710.h b/include/linux/cb710.h
index 63bc9a4d292..8cc10411bab 100644
--- a/include/linux/cb710.h
+++ b/include/linux/cb710.h
@@ -140,29 +140,6 @@ void cb710_dump_regs(struct cb710_chip *chip, unsigned dump);
 #include <linux/highmem.h>
 #include <linux/scatterlist.h>
 
-/**
- * cb710_sg_miter_stop_writing - stop mapping iteration after writing
- * @miter: sg mapping iter to be stopped
- *
- * Description:
- *   Stops mapping iterator @miter.  @miter should have been started
- *   started using sg_miter_start().  A stopped iteration can be
- *   resumed by calling sg_miter_next() on it.  This is useful when
- *   resources (kmap) need to be released during iteration.
- *
- *   This is a convenience wrapper that will be optimized out for arches
- *   that don't need flush_kernel_dcache_page().
- *
- * Context:
- *   IRQ disabled if the SG_MITER_ATOMIC is set.  Don't care otherwise.
- */
-static inline void cb710_sg_miter_stop_writing(struct sg_mapping_iter *miter)
-{
-	if (miter->page)
-		flush_kernel_dcache_page(miter->page);
-	sg_miter_stop(miter);
-}
-
 /*
  * 32-bit PIO mapping sg iterator
  *
@@ -171,12 +148,12 @@ static inline void cb710_sg_miter_stop_writing(struct sg_mapping_iter *miter)
  * without DMA support).
  *
  * Best-case reading (transfer from device):
- *   sg_miter_start();
+ *   sg_miter_start(, SG_MITER_TO_SG);
  *   cb710_sg_dwiter_write_from_io();
- *   cb710_sg_miter_stop_writing();
+ *   sg_miter_stop();
  *
  * Best-case writing (transfer to device):
- *   sg_miter_start();
+ *   sg_miter_start(, SG_MITER_FROM_SG);
  *   cb710_sg_dwiter_read_to_io();
  *   sg_miter_stop();
  */
-- 
GitLab


From a9239d750d9991f2feee78fc5669a4613abc1adb Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Sun, 28 Jun 2009 09:26:31 -0700
Subject: [PATCH 0377/1153] imxmmc: Remove unnecessary semicolons

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
---
 drivers/mmc/host/imxmmc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mmc/host/imxmmc.c b/drivers/mmc/host/imxmmc.c
index e0be21a4a69..bf98d7cc928 100644
--- a/drivers/mmc/host/imxmmc.c
+++ b/drivers/mmc/host/imxmmc.c
@@ -652,7 +652,7 @@ static irqreturn_t imxmci_irq(int irq, void *devid)
 	set_bit(IMXMCI_PEND_STARTED_b, &host->pending_events);
 	tasklet_schedule(&host->tasklet);
 
-	return IRQ_RETVAL(handled);;
+	return IRQ_RETVAL(handled);
 }
 
 static void imxmci_tasklet_fnc(unsigned long data)
-- 
GitLab


From 3822a0e38c329a598cb6f5baa16be7504e0db8d9 Mon Sep 17 00:00:00 2001
From: Pierre Ossman <pierre@ossman.eu>
Date: Fri, 31 Jul 2009 12:27:28 +0200
Subject: [PATCH 0378/1153] mmc: orphan subsystem

I do not have the time to take care of this, so remove myself as
maintainer.

Signed-off-by: Pierre Ossman <pierre@ossman.eu>
---
 MAINTAINERS | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 79471ba4981..d6befb2c470 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3420,8 +3420,7 @@ S:	Supported
 F:	drivers/mfd/
 
 MULTIMEDIA CARD (MMC), SECURE DIGITAL (SD) AND SDIO SUBSYSTEM
-M:	Pierre Ossman <pierre@ossman.eu>
-S:	Maintained
+S:	Orphan
 F:	drivers/mmc/
 F:	include/linux/mmc/
 
-- 
GitLab


From c7121843685de2bf7f3afd3ae1d6a146010bf1fc Mon Sep 17 00:00:00 2001
From: Magnus Damm <magnus.damm@gmail.com>
Date: Tue, 28 Jul 2009 14:09:55 -0700
Subject: [PATCH 0379/1153] clocksource: Save mult_orig in
 clocksource_disable()

To fix the common case where ->enable() does not set up
mult, make sure mult_orig is saved in mult on disable.

Also add comments to explain why we do this.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: johnstul@us.ibm.com
Cc: lethal@linux-sh.org
Cc: akpm@linux-foundation.org
LKML-Reference: <20090618152432.10136.9932.sendpatchset@rx1.opensource.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 include/linux/clocksource.h | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)

diff --git a/include/linux/clocksource.h b/include/linux/clocksource.h
index c56457c8334..1219be4fb42 100644
--- a/include/linux/clocksource.h
+++ b/include/linux/clocksource.h
@@ -293,7 +293,12 @@ static inline int clocksource_enable(struct clocksource *cs)
 	if (cs->enable)
 		ret = cs->enable(cs);
 
-	/* save mult_orig on enable */
+	/*
+	 * The frequency may have changed while the clocksource
+	 * was disabled. If so the code in ->enable() must update
+	 * the mult value to reflect the new frequency. Make sure
+	 * mult_orig follows this change.
+	 */
 	cs->mult_orig = cs->mult;
 
 	return ret;
@@ -309,6 +314,13 @@ static inline int clocksource_enable(struct clocksource *cs)
  */
 static inline void clocksource_disable(struct clocksource *cs)
 {
+	/*
+	 * Save mult_orig in mult so clocksource_enable() can
+	 * restore the value regardless if ->enable() updates
+	 * the value of mult or not.
+	 */
+	cs->mult = cs->mult_orig;
+
 	if (cs->disable)
 		cs->disable(cs);
 }
-- 
GitLab


From ff46a474ca2566d79e8d7454442b56d82bce37c1 Mon Sep 17 00:00:00 2001
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Date: Fri, 31 Jul 2009 15:42:09 +0200
Subject: [PATCH 0380/1153] mx3: Fix double pin allocation in pcm037_eet.c

SPI pins are now allocated in pcm037.c, remove them from EET.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx3/pcm037_eet.c | 9 ---------
 1 file changed, 9 deletions(-)

diff --git a/arch/arm/mach-mx3/pcm037_eet.c b/arch/arm/mach-mx3/pcm037_eet.c
index fe52fb1bb8b..8d386000fc4 100644
--- a/arch/arm/mach-mx3/pcm037_eet.c
+++ b/arch/arm/mach-mx3/pcm037_eet.c
@@ -24,15 +24,6 @@
 #include "devices.h"
 
 static unsigned int pcm037_eet_pins[] = {
-	/* SPI #1 */
-	MX31_PIN_CSPI1_MISO__MISO,
-	MX31_PIN_CSPI1_MOSI__MOSI,
-	MX31_PIN_CSPI1_SCLK__SCLK,
-	MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
-	MX31_PIN_CSPI1_SS0__SS0,
-	MX31_PIN_CSPI1_SS1__SS1,
-	MX31_PIN_CSPI1_SS2__SS2,
-
 	/* Reserve and hardwire GPIO 57 high - S6E63D6 chipselect */
 	IOMUX_MODE(MX31_PIN_KEY_COL7, IOMUX_CONFIG_GPIO),
 	/* GPIO keys */
-- 
GitLab


From 6606bb97e146a387932efee263745b7240a11193 Mon Sep 17 00:00:00 2001
From: Josef Bacik <josef@redhat.com>
Date: Fri, 31 Jul 2009 11:03:58 -0400
Subject: [PATCH 0381/1153] Btrfs: fix btrfs_remove_from_free_space corner case

Yan Zheng hit a problem where we tried to remove some free space but failed
because we couldn't find the free space entry.  This is because the free space
was held within a bitmap that had a starting offset well before the actual
offset of the free space, and there were free space extents that were in the
same range as that offset, so tree_search_offset returned with NULL because we
couldn't find a free space extent that had that offset.  This is fixed by
making sure that if we fail to find the entry, we re-search again with
bitmap_only set to 1 and do an offset_to_bitmap so we can get the appropriate
bitmap.  A similar problem happens in btrfs_alloc_from_bitmap for the
clustering code, but that is not as bad since we will just go and redo our
cluster allocation.

Also this adds some debugging checks to make sure that the free space we are
trying to remove from the bitmap is in fact there.  This can probably go away
after a while, but since this code is only used by the tree-logging stuff it
would be nice to run with it for a while to make sure there are no problems.

Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/free-space-cache.c | 73 ++++++++++++++++++++++++++++++++-----
 1 file changed, 64 insertions(+), 9 deletions(-)

diff --git a/fs/btrfs/free-space-cache.c b/fs/btrfs/free-space-cache.c
index af99b78b288..5edcee3a617 100644
--- a/fs/btrfs/free-space-cache.c
+++ b/fs/btrfs/free-space-cache.c
@@ -414,11 +414,29 @@ static noinline int remove_from_bitmap(struct btrfs_block_group_cache *block_gro
 			      u64 *offset, u64 *bytes)
 {
 	u64 end;
+	u64 search_start, search_bytes;
+	int ret;
 
 again:
 	end = bitmap_info->offset +
 		(u64)(BITS_PER_BITMAP * block_group->sectorsize) - 1;
 
+	/*
+	 * XXX - this can go away after a few releases.
+	 *
+	 * since the only user of btrfs_remove_free_space is the tree logging
+	 * stuff, and the only way to test that is under crash conditions, we
+	 * want to have this debug stuff here just in case somethings not
+	 * working.  Search the bitmap for the space we are trying to use to
+	 * make sure its actually there.  If its not there then we need to stop
+	 * because something has gone wrong.
+	 */
+	search_start = *offset;
+	search_bytes = *bytes;
+	ret = search_bitmap(block_group, bitmap_info, &search_start,
+			    &search_bytes);
+	BUG_ON(ret < 0 || search_start != *offset);
+
 	if (*offset > bitmap_info->offset && *offset + *bytes > end) {
 		bitmap_clear_bits(block_group, bitmap_info, *offset,
 				  end - *offset + 1);
@@ -430,6 +448,7 @@ again:
 	}
 
 	if (*bytes) {
+		struct rb_node *next = rb_next(&bitmap_info->offset_index);
 		if (!bitmap_info->bytes) {
 			unlink_free_space(block_group, bitmap_info);
 			kfree(bitmap_info->bitmap);
@@ -438,16 +457,36 @@ again:
 			recalculate_thresholds(block_group);
 		}
 
-		bitmap_info = tree_search_offset(block_group,
-						 offset_to_bitmap(block_group,
-								  *offset),
-						 1, 0);
-		if (!bitmap_info)
+		/*
+		 * no entry after this bitmap, but we still have bytes to
+		 * remove, so something has gone wrong.
+		 */
+		if (!next)
 			return -EINVAL;
 
+		bitmap_info = rb_entry(next, struct btrfs_free_space,
+				       offset_index);
+
+		/*
+		 * if the next entry isn't a bitmap we need to return to let the
+		 * extent stuff do its work.
+		 */
 		if (!bitmap_info->bitmap)
 			return -EAGAIN;
 
+		/*
+		 * Ok the next item is a bitmap, but it may not actually hold
+		 * the information for the rest of this free space stuff, so
+		 * look for it, and if we don't find it return so we can try
+		 * everything over again.
+		 */
+		search_start = *offset;
+		search_bytes = *bytes;
+		ret = search_bitmap(block_group, bitmap_info, &search_start,
+				    &search_bytes);
+		if (ret < 0 || search_start != *offset)
+			return -EAGAIN;
+
 		goto again;
 	} else if (!bitmap_info->bytes) {
 		unlink_free_space(block_group, bitmap_info);
@@ -644,8 +683,17 @@ int btrfs_remove_free_space(struct btrfs_block_group_cache *block_group,
 again:
 	info = tree_search_offset(block_group, offset, 0, 0);
 	if (!info) {
-		WARN_ON(1);
-		goto out_lock;
+		/*
+		 * oops didn't find an extent that matched the space we wanted
+		 * to remove, look for a bitmap instead
+		 */
+		info = tree_search_offset(block_group,
+					  offset_to_bitmap(block_group, offset),
+					  1, 0);
+		if (!info) {
+			WARN_ON(1);
+			goto out_lock;
+		}
 	}
 
 	if (info->bytes < bytes && rb_next(&info->offset_index)) {
@@ -957,8 +1005,15 @@ static u64 btrfs_alloc_from_bitmap(struct btrfs_block_group_cache *block_group,
 	if (cluster->block_group != block_group)
 		goto out;
 
-	entry = tree_search_offset(block_group, search_start, 0, 0);
-
+	/*
+	 * search_start is the beginning of the bitmap, but at some point it may
+	 * be a good idea to point to the actual start of the free area in the
+	 * bitmap, so do the offset_to_bitmap trick anyway, and set bitmap_only
+	 * to 1 to make sure we get the bitmap entry
+	 */
+	entry = tree_search_offset(block_group,
+				   offset_to_bitmap(block_group, search_start),
+				   1, 0);
 	if (!entry || !entry->bitmap)
 		goto out;
 
-- 
GitLab


From 013f1b12f4fc479f697acae2f31bad220162cd03 Mon Sep 17 00:00:00 2001
From: Chris Mason <chris.mason@oracle.com>
Date: Fri, 31 Jul 2009 14:57:55 -0400
Subject: [PATCH 0382/1153] Btrfs: make sure the async caching thread advances
 the key

The async caching thread can end up looping forever if a given
search puts it at the last key in a leaf.  It will end up calling
btrfs_next_leaf and then checking if it needs to politely drop
the read semaphore.

Most of the time this looping isn't noticed because it is able to
make progress the next time around.  But, during log replay,
we wait on the async caching thread to finish, and the async thread
is waiting on the commit, and no progress is really made.

The fix used here is to copy the key out of the next leaf,
that way our search lands there properly.

Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/extent-tree.c | 21 +++++++++++++++++----
 1 file changed, 17 insertions(+), 4 deletions(-)

diff --git a/fs/btrfs/extent-tree.c b/fs/btrfs/extent-tree.c
index dc84daee6bc..72a2b9c28e9 100644
--- a/fs/btrfs/extent-tree.c
+++ b/fs/btrfs/extent-tree.c
@@ -265,10 +265,6 @@ static int caching_kthread(void *data)
 
 	atomic_inc(&block_group->space_info->caching_threads);
 	last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET);
-again:
-	/* need to make sure the commit_root doesn't disappear */
-	down_read(&fs_info->extent_commit_sem);
-
 	/*
 	 * We don't want to deadlock with somebody trying to allocate a new
 	 * extent for the extent root while also trying to search the extent
@@ -282,6 +278,10 @@ again:
 	key.objectid = last;
 	key.offset = 0;
 	btrfs_set_key_type(&key, BTRFS_EXTENT_ITEM_KEY);
+again:
+	/* need to make sure the commit_root doesn't disappear */
+	down_read(&fs_info->extent_commit_sem);
+
 	ret = btrfs_search_slot(NULL, fs_info->extent_root, &key, path, 0, 0);
 	if (ret < 0)
 		goto err;
@@ -304,6 +304,19 @@ again:
 
 			if (need_resched() ||
 			    btrfs_transaction_in_commit(fs_info)) {
+				leaf = path->nodes[0];
+
+				/* this shouldn't happen, but if the
+				 * leaf is empty just move on.
+				 */
+				if (btrfs_header_nritems(leaf) == 0)
+					break;
+				/*
+				 * we need to copy the key out so that
+				 * we are sure the next search advances
+				 * us forward in the btree.
+				 */
+				btrfs_item_key_to_cpu(leaf, &key, 0);
 				btrfs_release_path(fs_info->extent_root, path);
 				up_read(&fs_info->extent_commit_sem);
 				schedule_timeout(1);
-- 
GitLab


From ab57a40827d99e2d8e59066a56b93bf6c844c916 Mon Sep 17 00:00:00 2001
From: Goldwyn Rodrigues <rgoldwyn@gmail.com>
Date: Fri, 31 Jul 2009 14:28:02 -0500
Subject: [PATCH 0383/1153] ocfs2: Remove redundant BUG_ON in __dlm_queue_ast()

We BUG_ON() the same thing twice.

Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/dlm/dlmast.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/fs/ocfs2/dlm/dlmast.c b/fs/ocfs2/dlm/dlmast.c
index d07ddbe4b28..81eff8e5832 100644
--- a/fs/ocfs2/dlm/dlmast.c
+++ b/fs/ocfs2/dlm/dlmast.c
@@ -103,7 +103,6 @@ static void __dlm_queue_ast(struct dlm_ctxt *dlm, struct dlm_lock *lock)
 		     lock->ast_pending, lock->ml.type);
 		BUG();
 	}
-	BUG_ON(!list_empty(&lock->ast_list));
 	if (lock->ast_pending)
 		mlog(0, "lock has an ast getting flushed right now\n");
 
-- 
GitLab


From ed680c4ad478d0fee9740f7d029087f181346564 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Fri, 31 Jul 2009 17:40:45 -0700
Subject: [PATCH 0384/1153] Linux 2.6.31-rc5

---
 Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Makefile b/Makefile
index 063d738405e..0d46615bffe 100644
--- a/Makefile
+++ b/Makefile
@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 31
-EXTRAVERSION = -rc4
+EXTRAVERSION = -rc5
 NAME = Man-Eating Seals of Antiquity
 
 # *DOCUMENTATION*
-- 
GitLab


From fef246672b009cf3f7a74e2fc9a76932ef2eeed2 Mon Sep 17 00:00:00 2001
From: "Martin K. Petersen" <martin.petersen@oracle.com>
Date: Fri, 31 Jul 2009 11:49:10 -0400
Subject: [PATCH 0385/1153] block: Make blk_queue_stack_limits use the new
 stacking interface

blk_queue_stack_limits() has been superceded by blk_stack_limits() and
disk_stack_limits().  Wrap the function call for now, we'll deprecate it
later.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 block/blk-settings.c | 22 +---------------------
 1 file changed, 1 insertion(+), 21 deletions(-)

diff --git a/block/blk-settings.c b/block/blk-settings.c
index 8a3ea3bba10..8e86e2d2b14 100644
--- a/block/blk-settings.c
+++ b/block/blk-settings.c
@@ -433,27 +433,7 @@ EXPORT_SYMBOL(blk_queue_io_opt);
  **/
 void blk_queue_stack_limits(struct request_queue *t, struct request_queue *b)
 {
-	/* zero is "infinity" */
-	t->limits.max_sectors = min_not_zero(queue_max_sectors(t),
-					     queue_max_sectors(b));
-
-	t->limits.max_hw_sectors = min_not_zero(queue_max_hw_sectors(t),
-						queue_max_hw_sectors(b));
-
-	t->limits.seg_boundary_mask = min_not_zero(queue_segment_boundary(t),
-						   queue_segment_boundary(b));
-
-	t->limits.max_phys_segments = min_not_zero(queue_max_phys_segments(t),
-						   queue_max_phys_segments(b));
-
-	t->limits.max_hw_segments = min_not_zero(queue_max_hw_segments(t),
-						 queue_max_hw_segments(b));
-
-	t->limits.max_segment_size = min_not_zero(queue_max_segment_size(t),
-						  queue_max_segment_size(b));
-
-	t->limits.logical_block_size = max(queue_logical_block_size(t),
-					   queue_logical_block_size(b));
+	blk_stack_limits(&t->limits, &b->limits, 0);
 
 	if (!t->queue_lock)
 		WARN_ON_ONCE(1);
-- 
GitLab


From 7c958e32649e0c35801762878fb0b6da8c55a515 Mon Sep 17 00:00:00 2001
From: "Martin K. Petersen" <martin.petersen@oracle.com>
Date: Fri, 31 Jul 2009 11:49:11 -0400
Subject: [PATCH 0386/1153] block: Add a wrapper for setting minimum request
 size without a queue

Introduce blk_limits_io_min() and make blk_queue_io_min() call it.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 block/blk-settings.c   | 31 ++++++++++++++++++++++++-------
 include/linux/blkdev.h |  1 +
 2 files changed, 25 insertions(+), 7 deletions(-)

diff --git a/block/blk-settings.c b/block/blk-settings.c
index 8e86e2d2b14..1f719743416 100644
--- a/block/blk-settings.c
+++ b/block/blk-settings.c
@@ -383,6 +383,29 @@ void blk_queue_alignment_offset(struct request_queue *q, unsigned int offset)
 }
 EXPORT_SYMBOL(blk_queue_alignment_offset);
 
+/**
+ * blk_limits_io_min - set minimum request size for a device
+ * @limits: the queue limits
+ * @min:  smallest I/O size in bytes
+ *
+ * Description:
+ *   Some devices have an internal block size bigger than the reported
+ *   hardware sector size.  This function can be used to signal the
+ *   smallest I/O the device can perform without incurring a performance
+ *   penalty.
+ */
+void blk_limits_io_min(struct queue_limits *limits, unsigned int min)
+{
+	limits->io_min = min;
+
+	if (limits->io_min < limits->logical_block_size)
+		limits->io_min = limits->logical_block_size;
+
+	if (limits->io_min < limits->physical_block_size)
+		limits->io_min = limits->physical_block_size;
+}
+EXPORT_SYMBOL(blk_limits_io_min);
+
 /**
  * blk_queue_io_min - set minimum request size for the queue
  * @q:	the request queue for the device
@@ -396,13 +419,7 @@ EXPORT_SYMBOL(blk_queue_alignment_offset);
  */
 void blk_queue_io_min(struct request_queue *q, unsigned int min)
 {
-	q->limits.io_min = min;
-
-	if (q->limits.io_min < q->limits.logical_block_size)
-		q->limits.io_min = q->limits.logical_block_size;
-
-	if (q->limits.io_min < q->limits.physical_block_size)
-		q->limits.io_min = q->limits.physical_block_size;
+	blk_limits_io_min(&q->limits, min);
 }
 EXPORT_SYMBOL(blk_queue_io_min);
 
diff --git a/include/linux/blkdev.h b/include/linux/blkdev.h
index e7cb5dbf6c2..69103e053c9 100644
--- a/include/linux/blkdev.h
+++ b/include/linux/blkdev.h
@@ -913,6 +913,7 @@ extern void blk_queue_logical_block_size(struct request_queue *, unsigned short)
 extern void blk_queue_physical_block_size(struct request_queue *, unsigned short);
 extern void blk_queue_alignment_offset(struct request_queue *q,
 				       unsigned int alignment);
+extern void blk_limits_io_min(struct queue_limits *limits, unsigned int min);
 extern void blk_queue_io_min(struct request_queue *q, unsigned int min);
 extern void blk_queue_io_opt(struct request_queue *q, unsigned int opt);
 extern void blk_set_default_limits(struct queue_limits *lim);
-- 
GitLab


From 70dd5bf3b99964d52862ad2810c24cc32a553535 Mon Sep 17 00:00:00 2001
From: "Martin K. Petersen" <martin.petersen@oracle.com>
Date: Fri, 31 Jul 2009 11:49:12 -0400
Subject: [PATCH 0387/1153] block: Stack optimal I/O size

When stacking block devices ensure that optimal I/O size is scaled
accordingly.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 block/blk-settings.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/block/blk-settings.c b/block/blk-settings.c
index 1f719743416..e1327ddfc13 100644
--- a/block/blk-settings.c
+++ b/block/blk-settings.c
@@ -7,6 +7,7 @@
 #include <linux/bio.h>
 #include <linux/blkdev.h>
 #include <linux/bootmem.h>	/* for max_pfn/max_low_pfn */
+#include <linux/gcd.h>
 
 #include "blk.h"
 
@@ -520,6 +521,16 @@ int blk_stack_limits(struct queue_limits *t, struct queue_limits *b,
 		return -1;
 	}
 
+	/* Find lcm() of optimal I/O size */
+	if (t->io_opt && b->io_opt)
+		t->io_opt = (t->io_opt * b->io_opt) / gcd(t->io_opt, b->io_opt);
+	else if (b->io_opt)
+		t->io_opt = b->io_opt;
+
+	/* Verify that optimal I/O size is a multiple of io_min */
+	if (t->io_min && t->io_opt % t->io_min)
+		return -1;
+
 	return 0;
 }
 EXPORT_SYMBOL(blk_stack_limits);
-- 
GitLab


From 7e5f5fb09e6fc657f21816b5a18ba645a913368e Mon Sep 17 00:00:00 2001
From: "Martin K. Petersen" <martin.petersen@oracle.com>
Date: Fri, 31 Jul 2009 11:49:13 -0400
Subject: [PATCH 0388/1153] block: Update topology documentation

Update topology comments and sysfs documentation based upon discussions
with Neil Brown.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 Documentation/ABI/testing/sysfs-block | 37 +++++++++++++++++----------
 block/blk-settings.c                  | 19 +++++++++-----
 2 files changed, 36 insertions(+), 20 deletions(-)

diff --git a/Documentation/ABI/testing/sysfs-block b/Documentation/ABI/testing/sysfs-block
index cbbd3e06994..5f3bedaf8e3 100644
--- a/Documentation/ABI/testing/sysfs-block
+++ b/Documentation/ABI/testing/sysfs-block
@@ -94,28 +94,37 @@ What:		/sys/block/<disk>/queue/physical_block_size
 Date:		May 2009
 Contact:	Martin K. Petersen <martin.petersen@oracle.com>
 Description:
-		This is the smallest unit the storage device can write
-		without resorting to read-modify-write operation.  It is
-		usually the same as the logical block size but may be
-		bigger.  One example is SATA drives with 4KB sectors
-		that expose a 512-byte logical block size to the
-		operating system.
+		This is the smallest unit a physical storage device can
+		write atomically.  It is usually the same as the logical
+		block size but may be bigger.  One example is SATA
+		drives with 4KB sectors that expose a 512-byte logical
+		block size to the operating system.  For stacked block
+		devices the physical_block_size variable contains the
+		maximum physical_block_size of the component devices.
 
 What:		/sys/block/<disk>/queue/minimum_io_size
 Date:		April 2009
 Contact:	Martin K. Petersen <martin.petersen@oracle.com>
 Description:
-		Storage devices may report a preferred minimum I/O size,
-		which is the smallest request the device can perform
-		without incurring a read-modify-write penalty.  For disk
-		drives this is often the physical block size.  For RAID
-		arrays it is often the stripe chunk size.
+		Storage devices may report a granularity or preferred
+		minimum I/O size which is the smallest request the
+		device can perform without incurring a performance
+		penalty.  For disk drives this is often the physical
+		block size.  For RAID arrays it is often the stripe
+		chunk size.  A properly aligned multiple of
+		minimum_io_size is the preferred request size for
+		workloads where a high number of I/O operations is
+		desired.
 
 What:		/sys/block/<disk>/queue/optimal_io_size
 Date:		April 2009
 Contact:	Martin K. Petersen <martin.petersen@oracle.com>
 Description:
 		Storage devices may report an optimal I/O size, which is
-		the device's preferred unit of receiving I/O.  This is
-		rarely reported for disk drives.  For RAID devices it is
-		usually the stripe width or the internal block size.
+		the device's preferred unit for sustained I/O.  This is
+		rarely reported for disk drives.  For RAID arrays it is
+		usually the stripe width or the internal track size.  A
+		properly aligned multiple of optimal_io_size is the
+		preferred request size for workloads where sustained
+		throughput is desired.  If no optimal I/O size is
+		reported this file contains 0.
diff --git a/block/blk-settings.c b/block/blk-settings.c
index e1327ddfc13..476d8706507 100644
--- a/block/blk-settings.c
+++ b/block/blk-settings.c
@@ -413,10 +413,13 @@ EXPORT_SYMBOL(blk_limits_io_min);
  * @min:  smallest I/O size in bytes
  *
  * Description:
- *   Some devices have an internal block size bigger than the reported
- *   hardware sector size.  This function can be used to signal the
- *   smallest I/O the device can perform without incurring a performance
- *   penalty.
+ *   Storage devices may report a granularity or preferred minimum I/O
+ *   size which is the smallest request the device can perform without
+ *   incurring a performance penalty.  For disk drives this is often the
+ *   physical block size.  For RAID arrays it is often the stripe chunk
+ *   size.  A properly aligned multiple of minimum_io_size is the
+ *   preferred request size for workloads where a high number of I/O
+ *   operations is desired.
  */
 void blk_queue_io_min(struct request_queue *q, unsigned int min)
 {
@@ -430,8 +433,12 @@ EXPORT_SYMBOL(blk_queue_io_min);
  * @opt:  optimal request size in bytes
  *
  * Description:
- *   Drivers can call this function to set the preferred I/O request
- *   size for devices that report such a value.
+ *   Storage devices may report an optimal I/O size, which is the
+ *   device's preferred unit for sustained I/O.  This is rarely reported
+ *   for disk drives.  For RAID arrays it is usually the stripe width or
+ *   the internal track size.  A properly aligned multiple of
+ *   optimal_io_size is the preferred request size for workloads where
+ *   sustained throughput is desired.
  */
 void blk_queue_io_opt(struct request_queue *q, unsigned int opt)
 {
-- 
GitLab


From 2d1b6949d2c855f195de0f5146625015ecca3944 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Sat, 1 Aug 2009 13:15:36 +0200
Subject: [PATCH 0389/1153] perf_counter tools: Fix link errors with older
 toolchains

On older distros (F8 for example) the perf build could fail
with such missing symbols:

    LINK perf
/usr/lib/gcc/x86_64-redhat-linux/4.3.2/../../../../lib64/libbfd.a(bfd.o): In function `bfd_demangle':
(.text+0x2b3): undefined reference to `cplus_demangle'
/usr/lib/gcc/x86_64-redhat-linux/4.3.2/../../../../lib64/libbfd.a(bfd.o): In function `bfd_demangle':

Link in -liberty too.

Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/tools/perf/Makefile b/tools/perf/Makefile
index a5e9b876ca0..4b20fa47c3a 100644
--- a/tools/perf/Makefile
+++ b/tools/perf/Makefile
@@ -345,7 +345,7 @@ BUILTIN_OBJS += builtin-stat.o
 BUILTIN_OBJS += builtin-top.o
 
 PERFLIBS = $(LIB_FILE)
-EXTLIBS = -lbfd
+EXTLIBS = -lbfd -liberty
 
 #
 # Platform specific tweaks
-- 
GitLab


From a97778457f22181e8c38c4cd7d7e528378738a98 Mon Sep 17 00:00:00 2001
From: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Date: Tue, 28 Jul 2009 17:55:29 +0900
Subject: [PATCH 0390/1153] nilfs2: fix oops due to inconsistent state in page
 with discrete b-tree nodes

Andrea Gelmini gave me a report that a kernel oops hit on a nilfs
filesystem with a 1KB block size when doing rsync.

This turned out to be caused by an inconsistency of dirty state
between a page and its buffers storing b-tree node blocks.

If the page had multiple buffers split over multiple logs, and if the
logs were written at a time, a dirty flag remained in the page even
every dirty flag in the buffers was cleared.

This will fix the failure by dropping the dirty flag properly for
pages with the discrete multiple b-tree nodes.

Reported-by: Andrea Gelmini <andrea.gelmini@gmail.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Andrea Gelmini <andrea.gelmini@gmail.com>
Cc: stable@kernel.org
---
 fs/nilfs2/segment.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/fs/nilfs2/segment.c b/fs/nilfs2/segment.c
index 8b5e4778cf2..51ff3d0a4ee 100644
--- a/fs/nilfs2/segment.c
+++ b/fs/nilfs2/segment.c
@@ -1859,12 +1859,26 @@ static void nilfs_end_page_io(struct page *page, int err)
 	if (!page)
 		return;
 
-	if (buffer_nilfs_node(page_buffers(page)) && !PageWriteback(page))
+	if (buffer_nilfs_node(page_buffers(page)) && !PageWriteback(page)) {
 		/*
 		 * For b-tree node pages, this function may be called twice
 		 * or more because they might be split in a segment.
 		 */
+		if (PageDirty(page)) {
+			/*
+			 * For pages holding split b-tree node buffers, dirty
+			 * flag on the buffers may be cleared discretely.
+			 * In that case, the page is once redirtied for
+			 * remaining buffers, and it must be cancelled if
+			 * all the buffers get cleaned later.
+			 */
+			lock_page(page);
+			if (nilfs_page_buffers_clean(page))
+				__nilfs_clear_page_dirty(page);
+			unlock_page(page);
+		}
 		return;
+	}
 
 	__nilfs_end_page_io(page, err);
 }
-- 
GitLab


From 0083fc2c50e6c5127c2802ad323adf8143ab7856 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sat, 1 Aug 2009 10:34:56 -0700
Subject: [PATCH 0391/1153] do_sigaltstack: avoid copying 'stack_t' as a
 structure to user space

Ulrich Drepper correctly points out that there is generally padding in
the structure on 64-bit hosts, and that copying the structure from
kernel to user space can leak information from the kernel stack in those
padding bytes.

Avoid the whole issue by just copying the three members one by one
instead, which also means that the function also can avoid the need for
a stack frame.  This also happens to match how we copy the new structure
from user space, so it all even makes sense.

[ The obvious solution of adding a memset() generates horrid code, gcc
  does really stupid things. ]

Reported-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/signal.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/kernel/signal.c b/kernel/signal.c
index ccf1ceedaeb..f268372c0cc 100644
--- a/kernel/signal.c
+++ b/kernel/signal.c
@@ -2454,11 +2454,9 @@ do_sigaltstack (const stack_t __user *uss, stack_t __user *uoss, unsigned long s
 	stack_t oss;
 	int error;
 
-	if (uoss) {
-		oss.ss_sp = (void __user *) current->sas_ss_sp;
-		oss.ss_size = current->sas_ss_size;
-		oss.ss_flags = sas_ss_flags(sp);
-	}
+	oss.ss_sp = (void __user *) current->sas_ss_sp;
+	oss.ss_size = current->sas_ss_size;
+	oss.ss_flags = sas_ss_flags(sp);
 
 	if (uss) {
 		void __user *ss_sp;
@@ -2501,13 +2499,16 @@ do_sigaltstack (const stack_t __user *uss, stack_t __user *uoss, unsigned long s
 		current->sas_ss_size = ss_size;
 	}
 
+	error = 0;
 	if (uoss) {
 		error = -EFAULT;
-		if (copy_to_user(uoss, &oss, sizeof(oss)))
+		if (!access_ok(VERIFY_WRITE, uoss, sizeof(*uoss)))
 			goto out;
+		error = __put_user(oss.ss_sp, &uoss->ss_sp) |
+			__put_user(oss.ss_size, &uoss->ss_size) |
+			__put_user(oss.ss_flags, &uoss->ss_flags);
 	}
 
-	error = 0;
 out:
 	return error;
 }
-- 
GitLab


From 0dd8486b5cfe8048e0613334659d9252ecd1b08a Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sat, 1 Aug 2009 11:18:56 -0700
Subject: [PATCH 0392/1153] do_sigaltstack: small cleanups

The previous commit ("do_sigaltstack: avoid copying 'stack_t' as a
structure to user space") fixed a real bug.  This one just cleans up the
copy from user space to that gcc can generate better code for it (and so
that it looks the same as the later copy back to user space).

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/signal.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/kernel/signal.c b/kernel/signal.c
index f268372c0cc..64c5deeaca5 100644
--- a/kernel/signal.c
+++ b/kernel/signal.c
@@ -2464,10 +2464,12 @@ do_sigaltstack (const stack_t __user *uss, stack_t __user *uoss, unsigned long s
 		int ss_flags;
 
 		error = -EFAULT;
-		if (!access_ok(VERIFY_READ, uss, sizeof(*uss))
-		    || __get_user(ss_sp, &uss->ss_sp)
-		    || __get_user(ss_flags, &uss->ss_flags)
-		    || __get_user(ss_size, &uss->ss_size))
+		if (!access_ok(VERIFY_READ, uss, sizeof(*uss)))
+			goto out;
+		error = __get_user(ss_sp, &uss->ss_sp) |
+			__get_user(ss_flags, &uss->ss_flags) |
+			__get_user(ss_size, &uss->ss_size);
+		if (error)
 			goto out;
 
 		error = -EPERM;
-- 
GitLab


From 550e7fd8afb7664ae7cedb398c407694e2bf7d3c Mon Sep 17 00:00:00 2001
From: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Date: Sat, 1 Aug 2009 12:04:17 -0300
Subject: [PATCH 0393/1153] thinkpad-acpi: disable broken bay and dock
 subdrivers

Currently, the ThinkPad-ACPI bay and dock drivers are completely
broken, and cause a NULL pointer derreference in kernel mode (and,
therefore, an OOPS) when they try to issue events (i.e. on dock,
undock, bay ejection, etc).

OTOH, the standard ACPI dock driver can handle the hotplug bays and
docks of the ThinkPads just fine (including batteries) as of 2.6.27.
In fact, it does a much better job of it than thinkpad-acpi ever did.

It is just not worth the hassle to find a way to fix this crap without
breaking the (deprecated) thinkpad-acpi dock/bay ABI.  This is old,
deprecated code that sees little testing or use.

As a quick fix suitable for -stable backports, mark the thinkpad-acpi
bay and dock subdrivers as BROKEN in Kconfig.  The dead code will be
removed by a later patch.

This fixes bugzilla #13669, and should be applied to 2.6.27 and later.

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Joerg Platte <jplatte@naasa.net>
Cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/platform/x86/Kconfig | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig
index 46dad12f952..6335f63892d 100644
--- a/drivers/platform/x86/Kconfig
+++ b/drivers/platform/x86/Kconfig
@@ -281,6 +281,7 @@ config THINKPAD_ACPI_DOCK
 	bool "Legacy Docking Station Support"
 	depends on THINKPAD_ACPI
 	depends on ACPI_DOCK=n
+	depends on BROKEN
 	default n
 	---help---
 	  Allows the thinkpad_acpi driver to handle docking station events.
@@ -294,7 +295,8 @@ config THINKPAD_ACPI_DOCK
 config THINKPAD_ACPI_BAY
 	bool "Legacy Removable Bay Support"
 	depends on THINKPAD_ACPI
-	default y
+	depends on BROKEN
+	default n
 	---help---
 	  Allows the thinkpad_acpi driver to handle removable bays.  It will
 	  electrically disable the device in the bay, and also generate
-- 
GitLab


From 1f6fc2de9525e34ee93bd392fa046369a8cfbf1e Mon Sep 17 00:00:00 2001
From: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Date: Sat, 1 Aug 2009 12:04:18 -0300
Subject: [PATCH 0394/1153] thinkpad-acpi: remove dock and bay subdrivers

The standard ACPI dock driver can handle the hotplug bays and docks of
the ThinkPads just fine (including batteries) as of 2.6.27, and the
code in thinkpad-acpi for the dock and bay subdrivers is currently
broken anyway...

Userspace needs some love to support the two-stage ejection nicely,
but it is simple enough to do through udev rules (you don't even need
HAL) so this wouldn't justify fixing the dock and bay subdrivers,
either.

That leaves warm-swap bays (_EJ3) support for thinkpad-acpi, as well
as support for the weird dock of the model 570, but since such support
has never left the "experimental" stage, it is also not a strong
enough reason to find a way to fix this code.

Users of ThinkPads with warm-swap bays are urged to request that _EJ3
support be added to the regular ACPI dock driver, if such feature is
indeed useful for them.

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 Documentation/laptops/thinkpad-acpi.txt | 127 ---------
 drivers/platform/x86/Kconfig            |  27 --
 drivers/platform/x86/thinkpad_acpi.c    | 327 ------------------------
 3 files changed, 481 deletions(-)

diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt
index f2296ecedb8..e2ddcdeb61b 100644
--- a/Documentation/laptops/thinkpad-acpi.txt
+++ b/Documentation/laptops/thinkpad-acpi.txt
@@ -36,8 +36,6 @@ detailed description):
 	- Bluetooth enable and disable
 	- video output switching, expansion control
 	- ThinkLight on and off
-	- limited docking and undocking
-	- UltraBay eject
 	- CMOS/UCMS control
 	- LED control
 	- ACPI sounds
@@ -729,131 +727,6 @@ cannot be read or if it is unknown, thinkpad-acpi will report it as "off".
 It is impossible to know if the status returned through sysfs is valid.
 
 
-Docking / undocking -- /proc/acpi/ibm/dock
-------------------------------------------
-
-Docking and undocking (e.g. with the X4 UltraBase) requires some
-actions to be taken by the operating system to safely make or break
-the electrical connections with the dock.
-
-The docking feature of this driver generates the following ACPI events:
-
-	ibm/dock GDCK 00000003 00000001 -- eject request
-	ibm/dock GDCK 00000003 00000002 -- undocked
-	ibm/dock GDCK 00000000 00000003 -- docked
-
-NOTE: These events will only be generated if the laptop was docked
-when originally booted. This is due to the current lack of support for
-hot plugging of devices in the Linux ACPI framework. If the laptop was
-booted while not in the dock, the following message is shown in the
-logs:
-
-	Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present
-
-In this case, no dock-related events are generated but the dock and
-undock commands described below still work. They can be executed
-manually or triggered by Fn key combinations (see the example acpid
-configuration files included in the driver tarball package available
-on the web site).
-
-When the eject request button on the dock is pressed, the first event
-above is generated. The handler for this event should issue the
-following command:
-
-	echo undock > /proc/acpi/ibm/dock
-
-After the LED on the dock goes off, it is safe to eject the laptop.
-Note: if you pressed this key by mistake, go ahead and eject the
-laptop, then dock it back in. Otherwise, the dock may not function as
-expected.
-
-When the laptop is docked, the third event above is generated. The
-handler for this event should issue the following command to fully
-enable the dock:
-
-	echo dock > /proc/acpi/ibm/dock
-
-The contents of the /proc/acpi/ibm/dock file shows the current status
-of the dock, as provided by the ACPI framework.
-
-The docking support in this driver does not take care of enabling or
-disabling any other devices you may have attached to the dock. For
-example, a CD drive plugged into the UltraBase needs to be disabled or
-enabled separately. See the provided example acpid configuration files
-for how this can be accomplished.
-
-There is no support yet for PCI devices that may be attached to a
-docking station, e.g. in the ThinkPad Dock II. The driver currently
-does not recognize, enable or disable such devices. This means that
-the only docking stations currently supported are the X-series
-UltraBase docks and "dumb" port replicators like the Mini Dock (the
-latter don't need any ACPI support, actually).
-
-
-UltraBay eject -- /proc/acpi/ibm/bay
-------------------------------------
-
-Inserting or ejecting an UltraBay device requires some actions to be
-taken by the operating system to safely make or break the electrical
-connections with the device.
-
-This feature generates the following ACPI events:
-
-	ibm/bay MSTR 00000003 00000000 -- eject request
-	ibm/bay MSTR 00000001 00000000 -- eject lever inserted
-
-NOTE: These events will only be generated if the UltraBay was present
-when the laptop was originally booted (on the X series, the UltraBay
-is in the dock, so it may not be present if the laptop was undocked).
-This is due to the current lack of support for hot plugging of devices
-in the Linux ACPI framework. If the laptop was booted without the
-UltraBay, the following message is shown in the logs:
-
-	Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present
-
-In this case, no bay-related events are generated but the eject
-command described below still works. It can be executed manually or
-triggered by a hot key combination.
-
-Sliding the eject lever generates the first event shown above. The
-handler for this event should take whatever actions are necessary to
-shut down the device in the UltraBay (e.g. call idectl), then issue
-the following command:
-
-	echo eject > /proc/acpi/ibm/bay
-
-After the LED on the UltraBay goes off, it is safe to pull out the
-device.
-
-When the eject lever is inserted, the second event above is
-generated. The handler for this event should take whatever actions are
-necessary to enable the UltraBay device (e.g. call idectl).
-
-The contents of the /proc/acpi/ibm/bay file shows the current status
-of the UltraBay, as provided by the ACPI framework.
-
-EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use
-this feature, you need to supply the experimental=1 parameter when
-loading the module):
-
-These models do not have a button near the UltraBay device to request
-a hot eject but rather require the laptop to be put to sleep
-(suspend-to-ram) before the bay device is ejected or inserted).
-The sequence of steps to eject the device is as follows:
-
-	echo eject > /proc/acpi/ibm/bay
-	put the ThinkPad to sleep
-	remove the drive
-	resume from sleep
-	cat /proc/acpi/ibm/bay should show that the drive was removed
-
-On the A3x, both the UltraBay 2000 and UltraBay Plus devices are
-supported. Use "eject2" instead of "eject" for the second bay.
-
-Note: the UltraBay eject support on the 600e/x, A22p and A3x is
-EXPERIMENTAL and may not work as expected. USE WITH CAUTION!
-
-
 CMOS/UCMS control
 -----------------
 
diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig
index 6335f63892d..77c6097ced8 100644
--- a/drivers/platform/x86/Kconfig
+++ b/drivers/platform/x86/Kconfig
@@ -277,33 +277,6 @@ config THINKPAD_ACPI_UNSAFE_LEDS
 	  Say N here, unless you are building a kernel for your own
 	  use, and need to control the important firmware LEDs.
 
-config THINKPAD_ACPI_DOCK
-	bool "Legacy Docking Station Support"
-	depends on THINKPAD_ACPI
-	depends on ACPI_DOCK=n
-	depends on BROKEN
-	default n
-	---help---
-	  Allows the thinkpad_acpi driver to handle docking station events.
-	  This support was made obsolete by the generic ACPI docking station
-	  support (CONFIG_ACPI_DOCK).  It will allow locking and removing the
-	  laptop from the docking station, but will not properly connect PCI
-	  devices.
-
-	  If you are not sure, say N here.
-
-config THINKPAD_ACPI_BAY
-	bool "Legacy Removable Bay Support"
-	depends on THINKPAD_ACPI
-	depends on BROKEN
-	default n
-	---help---
-	  Allows the thinkpad_acpi driver to handle removable bays.  It will
-	  electrically disable the device in the bay, and also generate
-	  notifications when the bay lever is ejected or inserted.
-
-	  If you are not sure, say Y here.
-
 config THINKPAD_ACPI_VIDEO
 	bool "Video output control support"
 	depends on THINKPAD_ACPI
diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c
index a463fd72c49..27d68e719e9 100644
--- a/drivers/platform/x86/thinkpad_acpi.c
+++ b/drivers/platform/x86/thinkpad_acpi.c
@@ -239,12 +239,6 @@ struct ibm_init_struct {
 };
 
 static struct {
-#ifdef CONFIG_THINKPAD_ACPI_BAY
-	u32 bay_status:1;
-	u32 bay_eject:1;
-	u32 bay_status2:1;
-	u32 bay_eject2:1;
-#endif
 	u32 bluetooth:1;
 	u32 hotkey:1;
 	u32 hotkey_mask:1;
@@ -589,18 +583,6 @@ static int acpi_ec_write(int i, u8 v)
 	return 1;
 }
 
-#if defined(CONFIG_THINKPAD_ACPI_DOCK) || defined(CONFIG_THINKPAD_ACPI_BAY)
-static int _sta(acpi_handle handle)
-{
-	int status;
-
-	if (!handle || !acpi_evalf(handle, &status, "_STA", "d"))
-		status = 0;
-
-	return status;
-}
-#endif
-
 static int issue_thinkpad_cmos_command(int cmos_cmd)
 {
 	if (!cmos_handle)
@@ -4441,293 +4423,6 @@ static struct ibm_struct light_driver_data = {
 	.exit = light_exit,
 };
 
-/*************************************************************************
- * Dock subdriver
- */
-
-#ifdef CONFIG_THINKPAD_ACPI_DOCK
-
-static void dock_notify(struct ibm_struct *ibm, u32 event);
-static int dock_read(char *p);
-static int dock_write(char *buf);
-
-TPACPI_HANDLE(dock, root, "\\_SB.GDCK",	/* X30, X31, X40 */
-	   "\\_SB.PCI0.DOCK",	/* 600e/x,770e,770x,A2xm/p,T20-22,X20-21 */
-	   "\\_SB.PCI0.PCI1.DOCK",	/* all others */
-	   "\\_SB.PCI.ISA.SLCE",	/* 570 */
-    );				/* A21e,G4x,R30,R31,R32,R40,R40e,R50e */
-
-/* don't list other alternatives as we install a notify handler on the 570 */
-TPACPI_HANDLE(pci, root, "\\_SB.PCI");	/* 570 */
-
-static const struct acpi_device_id ibm_pci_device_ids[] = {
-	{PCI_ROOT_HID_STRING, 0},
-	{"", 0},
-};
-
-static struct tp_acpi_drv_struct ibm_dock_acpidriver[2] = {
-	{
-	 .notify = dock_notify,
-	 .handle = &dock_handle,
-	 .type = ACPI_SYSTEM_NOTIFY,
-	},
-	{
-	/* THIS ONE MUST NEVER BE USED FOR DRIVER AUTOLOADING.
-	 * We just use it to get notifications of dock hotplug
-	 * in very old thinkpads */
-	 .hid = ibm_pci_device_ids,
-	 .notify = dock_notify,
-	 .handle = &pci_handle,
-	 .type = ACPI_SYSTEM_NOTIFY,
-	},
-};
-
-static struct ibm_struct dock_driver_data[2] = {
-	{
-	 .name = "dock",
-	 .read = dock_read,
-	 .write = dock_write,
-	 .acpi = &ibm_dock_acpidriver[0],
-	},
-	{
-	 .name = "dock",
-	 .acpi = &ibm_dock_acpidriver[1],
-	},
-};
-
-#define dock_docked() (_sta(dock_handle) & 1)
-
-static int __init dock_init(struct ibm_init_struct *iibm)
-{
-	vdbg_printk(TPACPI_DBG_INIT, "initializing dock subdriver\n");
-
-	TPACPI_ACPIHANDLE_INIT(dock);
-
-	vdbg_printk(TPACPI_DBG_INIT, "dock is %s\n",
-		str_supported(dock_handle != NULL));
-
-	return (dock_handle)? 0 : 1;
-}
-
-static int __init dock_init2(struct ibm_init_struct *iibm)
-{
-	int dock2_needed;
-
-	vdbg_printk(TPACPI_DBG_INIT, "initializing dock subdriver part 2\n");
-
-	if (dock_driver_data[0].flags.acpi_driver_registered &&
-	    dock_driver_data[0].flags.acpi_notify_installed) {
-		TPACPI_ACPIHANDLE_INIT(pci);
-		dock2_needed = (pci_handle != NULL);
-		vdbg_printk(TPACPI_DBG_INIT,
-			    "dock PCI handler for the TP 570 is %s\n",
-			    str_supported(dock2_needed));
-	} else {
-		vdbg_printk(TPACPI_DBG_INIT,
-		"dock subdriver part 2 not required\n");
-		dock2_needed = 0;
-	}
-
-	return (dock2_needed)? 0 : 1;
-}
-
-static void dock_notify(struct ibm_struct *ibm, u32 event)
-{
-	int docked = dock_docked();
-	int pci = ibm->acpi->hid && ibm->acpi->device &&
-		acpi_match_device_ids(ibm->acpi->device, ibm_pci_device_ids);
-	int data;
-
-	if (event == 1 && !pci)	/* 570 */
-		data = 1;	/* button */
-	else if (event == 1 && pci)	/* 570 */
-		data = 3;	/* dock */
-	else if (event == 3 && docked)
-		data = 1;	/* button */
-	else if (event == 3 && !docked)
-		data = 2;	/* undock */
-	else if (event == 0 && docked)
-		data = 3;	/* dock */
-	else {
-		printk(TPACPI_ERR "unknown dock event %d, status %d\n",
-		       event, _sta(dock_handle));
-		data = 0;	/* unknown */
-	}
-	acpi_bus_generate_proc_event(ibm->acpi->device, event, data);
-	acpi_bus_generate_netlink_event(ibm->acpi->device->pnp.device_class,
-					  dev_name(&ibm->acpi->device->dev),
-					  event, data);
-}
-
-static int dock_read(char *p)
-{
-	int len = 0;
-	int docked = dock_docked();
-
-	if (!dock_handle)
-		len += sprintf(p + len, "status:\t\tnot supported\n");
-	else if (!docked)
-		len += sprintf(p + len, "status:\t\tundocked\n");
-	else {
-		len += sprintf(p + len, "status:\t\tdocked\n");
-		len += sprintf(p + len, "commands:\tdock, undock\n");
-	}
-
-	return len;
-}
-
-static int dock_write(char *buf)
-{
-	char *cmd;
-
-	if (!dock_docked())
-		return -ENODEV;
-
-	while ((cmd = next_cmd(&buf))) {
-		if (strlencmp(cmd, "undock") == 0) {
-			if (!acpi_evalf(dock_handle, NULL, "_DCK", "vd", 0) ||
-			    !acpi_evalf(dock_handle, NULL, "_EJ0", "vd", 1))
-				return -EIO;
-		} else if (strlencmp(cmd, "dock") == 0) {
-			if (!acpi_evalf(dock_handle, NULL, "_DCK", "vd", 1))
-				return -EIO;
-		} else
-			return -EINVAL;
-	}
-
-	return 0;
-}
-
-#endif /* CONFIG_THINKPAD_ACPI_DOCK */
-
-/*************************************************************************
- * Bay subdriver
- */
-
-#ifdef CONFIG_THINKPAD_ACPI_BAY
-
-TPACPI_HANDLE(bay, root, "\\_SB.PCI.IDE.SECN.MAST",	/* 570 */
-	   "\\_SB.PCI0.IDE0.IDES.IDSM",	/* 600e/x, 770e, 770x */
-	   "\\_SB.PCI0.SATA.SCND.MSTR",	/* T60, X60, Z60 */
-	   "\\_SB.PCI0.IDE0.SCND.MSTR",	/* all others */
-	   );				/* A21e, R30, R31 */
-TPACPI_HANDLE(bay_ej, bay, "_EJ3",	/* 600e/x, A2xm/p, A3x */
-	   "_EJ0",		/* all others */
-	   );			/* 570,A21e,G4x,R30,R31,R32,R40e,R50e */
-TPACPI_HANDLE(bay2, root, "\\_SB.PCI0.IDE0.PRIM.SLAV",	/* A3x, R32 */
-	   "\\_SB.PCI0.IDE0.IDEP.IDPS",	/* 600e/x, 770e, 770x */
-	   );				/* all others */
-TPACPI_HANDLE(bay2_ej, bay2, "_EJ3",	/* 600e/x, 770e, A3x */
-	   "_EJ0",			/* 770x */
-	   );				/* all others */
-
-static int __init bay_init(struct ibm_init_struct *iibm)
-{
-	vdbg_printk(TPACPI_DBG_INIT, "initializing bay subdriver\n");
-
-	TPACPI_ACPIHANDLE_INIT(bay);
-	if (bay_handle)
-		TPACPI_ACPIHANDLE_INIT(bay_ej);
-	TPACPI_ACPIHANDLE_INIT(bay2);
-	if (bay2_handle)
-		TPACPI_ACPIHANDLE_INIT(bay2_ej);
-
-	tp_features.bay_status = bay_handle &&
-		acpi_evalf(bay_handle, NULL, "_STA", "qv");
-	tp_features.bay_status2 = bay2_handle &&
-		acpi_evalf(bay2_handle, NULL, "_STA", "qv");
-
-	tp_features.bay_eject = bay_handle && bay_ej_handle &&
-		(strlencmp(bay_ej_path, "_EJ0") == 0 || experimental);
-	tp_features.bay_eject2 = bay2_handle && bay2_ej_handle &&
-		(strlencmp(bay2_ej_path, "_EJ0") == 0 || experimental);
-
-	vdbg_printk(TPACPI_DBG_INIT,
-		"bay 1: status %s, eject %s; bay 2: status %s, eject %s\n",
-		str_supported(tp_features.bay_status),
-		str_supported(tp_features.bay_eject),
-		str_supported(tp_features.bay_status2),
-		str_supported(tp_features.bay_eject2));
-
-	return (tp_features.bay_status || tp_features.bay_eject ||
-		tp_features.bay_status2 || tp_features.bay_eject2)? 0 : 1;
-}
-
-static void bay_notify(struct ibm_struct *ibm, u32 event)
-{
-	acpi_bus_generate_proc_event(ibm->acpi->device, event, 0);
-	acpi_bus_generate_netlink_event(ibm->acpi->device->pnp.device_class,
-					  dev_name(&ibm->acpi->device->dev),
-					  event, 0);
-}
-
-#define bay_occupied(b) (_sta(b##_handle) & 1)
-
-static int bay_read(char *p)
-{
-	int len = 0;
-	int occupied = bay_occupied(bay);
-	int occupied2 = bay_occupied(bay2);
-	int eject, eject2;
-
-	len += sprintf(p + len, "status:\t\t%s\n",
-		tp_features.bay_status ?
-			(occupied ? "occupied" : "unoccupied") :
-				"not supported");
-	if (tp_features.bay_status2)
-		len += sprintf(p + len, "status2:\t%s\n", occupied2 ?
-			       "occupied" : "unoccupied");
-
-	eject = tp_features.bay_eject && occupied;
-	eject2 = tp_features.bay_eject2 && occupied2;
-
-	if (eject && eject2)
-		len += sprintf(p + len, "commands:\teject, eject2\n");
-	else if (eject)
-		len += sprintf(p + len, "commands:\teject\n");
-	else if (eject2)
-		len += sprintf(p + len, "commands:\teject2\n");
-
-	return len;
-}
-
-static int bay_write(char *buf)
-{
-	char *cmd;
-
-	if (!tp_features.bay_eject && !tp_features.bay_eject2)
-		return -ENODEV;
-
-	while ((cmd = next_cmd(&buf))) {
-		if (tp_features.bay_eject && strlencmp(cmd, "eject") == 0) {
-			if (!acpi_evalf(bay_ej_handle, NULL, NULL, "vd", 1))
-				return -EIO;
-		} else if (tp_features.bay_eject2 &&
-			   strlencmp(cmd, "eject2") == 0) {
-			if (!acpi_evalf(bay2_ej_handle, NULL, NULL, "vd", 1))
-				return -EIO;
-		} else
-			return -EINVAL;
-	}
-
-	return 0;
-}
-
-static struct tp_acpi_drv_struct ibm_bay_acpidriver = {
-	.notify = bay_notify,
-	.handle = &bay_handle,
-	.type = ACPI_SYSTEM_NOTIFY,
-};
-
-static struct ibm_struct bay_driver_data = {
-	.name = "bay",
-	.read = bay_read,
-	.write = bay_write,
-	.acpi = &ibm_bay_acpidriver,
-};
-
-#endif /* CONFIG_THINKPAD_ACPI_BAY */
-
 /*************************************************************************
  * CMOS subdriver
  */
@@ -7854,22 +7549,6 @@ static struct ibm_init_struct ibms_init[] __initdata = {
 		.init = light_init,
 		.data = &light_driver_data,
 	},
-#ifdef CONFIG_THINKPAD_ACPI_DOCK
-	{
-		.init = dock_init,
-		.data = &dock_driver_data[0],
-	},
-	{
-		.init = dock_init2,
-		.data = &dock_driver_data[1],
-	},
-#endif
-#ifdef CONFIG_THINKPAD_ACPI_BAY
-	{
-		.init = bay_init,
-		.data = &bay_driver_data,
-	},
-#endif
 	{
 		.init = cmos_init,
 		.data = &cmos_driver_data,
@@ -7968,12 +7647,6 @@ TPACPI_PARAM(hotkey);
 TPACPI_PARAM(bluetooth);
 TPACPI_PARAM(video);
 TPACPI_PARAM(light);
-#ifdef CONFIG_THINKPAD_ACPI_DOCK
-TPACPI_PARAM(dock);
-#endif
-#ifdef CONFIG_THINKPAD_ACPI_BAY
-TPACPI_PARAM(bay);
-#endif /* CONFIG_THINKPAD_ACPI_BAY */
 TPACPI_PARAM(cmos);
 TPACPI_PARAM(led);
 TPACPI_PARAM(beep);
-- 
GitLab


From 9b9d6b2434fe942895c341b9a982f158529788ec Mon Sep 17 00:00:00 2001
From: Jeff Layton <jlayton@redhat.com>
Date: Fri, 31 Jul 2009 06:56:09 -0400
Subject: [PATCH 0395/1153] cifs: reinstate original behavior when uid=/gid=
 options are specified

This patch fixes the regression reported here:

http://bugzilla.kernel.org/show_bug.cgi?id=13861

commit 4ae1507f6d266d0cc3dd36e474d83aad70fec9e4 changed the default
behavior when the uid= or gid= option was specified for a mount. The
existing behavior was to always clobber the ownership information
provided by the server when these options were specified. The above
commit changed this behavior so that these options simply provided
defaults when the server did not provide this information (unless
"forceuid" or "forcegid" were specified)

This patch reverts this change so that the default behavior is restored.
It also adds "noforceuid" and "noforcegid" options to make it so that
ownership information from the server is preserved, even when the mount
has uid= or gid= options specified.

It also adds a couple of printk notices that pop up when forceuid or
forcegid options are specified without a uid= or gid= option.

Reported-by: Tom Chiverton <bugzilla.kernel.org@falkensweb.com>
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
---
 fs/cifs/connect.c | 42 ++++++++++++++++++++++++++++++------------
 1 file changed, 30 insertions(+), 12 deletions(-)

diff --git a/fs/cifs/connect.c b/fs/cifs/connect.c
index f2486889b7b..1f3345d7fa7 100644
--- a/fs/cifs/connect.c
+++ b/fs/cifs/connect.c
@@ -803,6 +803,10 @@ cifs_parse_mount_options(char *options, const char *devname,
 	char *data;
 	unsigned int  temp_len, i, j;
 	char separator[2];
+	short int override_uid = -1;
+	short int override_gid = -1;
+	bool uid_specified = false;
+	bool gid_specified = false;
 
 	separator[0] = ',';
 	separator[1] = 0;
@@ -1093,18 +1097,20 @@ cifs_parse_mount_options(char *options, const char *devname,
 						    "too long.\n");
 				return 1;
 			}
-		} else if (strnicmp(data, "uid", 3) == 0) {
-			if (value && *value)
-				vol->linux_uid =
-					simple_strtoul(value, &value, 0);
-		} else if (strnicmp(data, "forceuid", 8) == 0) {
-				vol->override_uid = 1;
-		} else if (strnicmp(data, "gid", 3) == 0) {
-			if (value && *value)
-				vol->linux_gid =
-					simple_strtoul(value, &value, 0);
-		} else if (strnicmp(data, "forcegid", 8) == 0) {
-				vol->override_gid = 1;
+		} else if (!strnicmp(data, "uid", 3) && value && *value) {
+			vol->linux_uid = simple_strtoul(value, &value, 0);
+			uid_specified = true;
+		} else if (!strnicmp(data, "forceuid", 8)) {
+			override_uid = 1;
+		} else if (!strnicmp(data, "noforceuid", 10)) {
+			override_uid = 0;
+		} else if (!strnicmp(data, "gid", 3) && value && *value) {
+			vol->linux_gid = simple_strtoul(value, &value, 0);
+			gid_specified = true;
+		} else if (!strnicmp(data, "forcegid", 8)) {
+			override_gid = 1;
+		} else if (!strnicmp(data, "noforcegid", 10)) {
+			override_gid = 0;
 		} else if (strnicmp(data, "file_mode", 4) == 0) {
 			if (value && *value) {
 				vol->file_mode =
@@ -1355,6 +1361,18 @@ cifs_parse_mount_options(char *options, const char *devname,
 	if (vol->UNCip == NULL)
 		vol->UNCip = &vol->UNC[2];
 
+	if (uid_specified)
+		vol->override_uid = override_uid;
+	else if (override_uid == 1)
+		printk(KERN_NOTICE "CIFS: ignoring forceuid mount option "
+				   "specified with no uid= option.\n");
+
+	if (gid_specified)
+		vol->override_gid = override_gid;
+	else if (override_gid == 1)
+		printk(KERN_NOTICE "CIFS: ignoring forcegid mount option "
+				   "specified with no gid= option.\n");
+
 	return 0;
 }
 
-- 
GitLab


From 5b05d4696d38c3172e79e855cc1e2ed044589508 Mon Sep 17 00:00:00 2001
From: Michael Buesch <mb@bu3sch.de>
Date: Sat, 1 Aug 2009 12:04:19 -0300
Subject: [PATCH 0396/1153] thinkpad-acpi: restrict procfs count value to sane
 upper limit

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/platform/x86/thinkpad_acpi.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c
index 27d68e719e9..18f9ee63c50 100644
--- a/drivers/platform/x86/thinkpad_acpi.c
+++ b/drivers/platform/x86/thinkpad_acpi.c
@@ -766,6 +766,8 @@ static int dispatch_procfs_write(struct file *file,
 
 	if (!ibm || !ibm->write)
 		return -EINVAL;
+	if (count > PAGE_SIZE - 2)
+		return -EINVAL;
 
 	kernbuf = kmalloc(count + 2, GFP_KERNEL);
 	if (!kernbuf)
-- 
GitLab


From 59fe4fe34d7afdf63208124f313be9056feaa2f4 Mon Sep 17 00:00:00 2001
From: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Date: Sat, 1 Aug 2009 12:04:20 -0300
Subject: [PATCH 0397/1153] thinkpad-acpi: fix incorrect use of
 TPACPI_BRGHT_MODE_ECNVRAM

HBRV-based default selection of backlight control strategy didn't work
well, at least the X41 defines it but doesn't use it and I don't think
it will stop there.

Switch to a white/blacklist.  All models that have HBRV defined have
been included in the list, and initially all ATI GPUs will get
ECNVRAM, and the Intel GPUs will get UCMS_STEP.

Symptoms of incorrect backlight mode selection are:

1. Non-working backlight control through sysfs;

2. Backlight gets reset to the lowest level at every shutdown, reboot
   and when thinkpad-acpi gets unloaded;

This fixes a regression in 2.6.30, bugzilla #13826

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/platform/x86/thinkpad_acpi.c | 61 +++++++++++++++++++++-------
 1 file changed, 47 insertions(+), 14 deletions(-)

diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c
index 18f9ee63c50..e8560085250 100644
--- a/drivers/platform/x86/thinkpad_acpi.c
+++ b/drivers/platform/x86/thinkpad_acpi.c
@@ -5642,14 +5642,48 @@ static struct backlight_ops ibm_backlight_data = {
 
 /* --------------------------------------------------------------------- */
 
+/*
+ * These are only useful for models that have only one possibility
+ * of GPU.  If the BIOS model handles both ATI and Intel, don't use
+ * these quirks.
+ */
+#define TPACPI_BRGHT_Q_NOEC	0x0001	/* Must NOT use EC HBRV */
+#define TPACPI_BRGHT_Q_EC	0x0002  /* Should or must use EC HBRV */
+#define TPACPI_BRGHT_Q_ASK	0x8000	/* Ask for user report */
+
+static const struct tpacpi_quirk brightness_quirk_table[] __initconst = {
+	/* Models with ATI GPUs known to require ECNVRAM mode */
+	TPACPI_Q_IBM('1', 'Y', TPACPI_BRGHT_Q_EC),	/* T43/p ATI */
+
+	/* Models with ATI GPUs (waiting confirmation) */
+	TPACPI_Q_IBM('1', 'R', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC),
+	TPACPI_Q_IBM('1', 'Q', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC),
+	TPACPI_Q_IBM('7', '6', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC),
+	TPACPI_Q_IBM('7', '8', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_EC),
+
+	/* Models with Intel Extreme Graphics 2 (waiting confirmation) */
+	TPACPI_Q_IBM('1', 'V', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_NOEC),
+	TPACPI_Q_IBM('1', 'W', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_NOEC),
+	TPACPI_Q_IBM('1', 'U', TPACPI_BRGHT_Q_ASK|TPACPI_BRGHT_Q_NOEC),
+
+	/* Models with Intel GMA900 */
+	TPACPI_Q_IBM('7', '0', TPACPI_BRGHT_Q_NOEC),	/* T43, R52 */
+	TPACPI_Q_IBM('7', '4', TPACPI_BRGHT_Q_NOEC),	/* X41 */
+	TPACPI_Q_IBM('7', '5', TPACPI_BRGHT_Q_NOEC),	/* X41 Tablet */
+};
+
 static int __init brightness_init(struct ibm_init_struct *iibm)
 {
 	int b;
+	unsigned long quirks;
 
 	vdbg_printk(TPACPI_DBG_INIT, "initializing brightness subdriver\n");
 
 	mutex_init(&brightness_mutex);
 
+	quirks = tpacpi_check_quirks(brightness_quirk_table,
+				ARRAY_SIZE(brightness_quirk_table));
+
 	/*
 	 * We always attempt to detect acpi support, so as to switch
 	 * Lenovo Vista BIOS to ACPI brightness mode even if we are not
@@ -5706,23 +5740,13 @@ static int __init brightness_init(struct ibm_init_struct *iibm)
 	/* TPACPI_BRGHT_MODE_AUTO not implemented yet, just use default */
 	if (brightness_mode == TPACPI_BRGHT_MODE_AUTO ||
 	    brightness_mode == TPACPI_BRGHT_MODE_MAX) {
-		if (thinkpad_id.vendor == PCI_VENDOR_ID_IBM) {
-			/*
-			 * IBM models that define HBRV probably have
-			 * EC-based backlight level control
-			 */
-			if (acpi_evalf(ec_handle, NULL, "HBRV", "qd"))
-				/* T40-T43, R50-R52, R50e, R51e, X31-X41 */
-				brightness_mode = TPACPI_BRGHT_MODE_ECNVRAM;
-			else
-				/* all other IBM ThinkPads */
-				brightness_mode = TPACPI_BRGHT_MODE_UCMS_STEP;
-		} else
-			/* All Lenovo ThinkPads */
+		if (quirks & TPACPI_BRGHT_Q_EC)
+			brightness_mode = TPACPI_BRGHT_MODE_ECNVRAM;
+		else
 			brightness_mode = TPACPI_BRGHT_MODE_UCMS_STEP;
 
 		dbg_printk(TPACPI_DBG_BRGHT,
-			   "selected brightness_mode=%d\n",
+			   "driver auto-selected brightness_mode=%d\n",
 			   brightness_mode);
 	}
 
@@ -5749,6 +5773,15 @@ static int __init brightness_init(struct ibm_init_struct *iibm)
 	vdbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_BRGHT,
 			"brightness is supported\n");
 
+	if (quirks & TPACPI_BRGHT_Q_ASK) {
+		printk(TPACPI_NOTICE
+			"brightness: will use unverified default: "
+			"brightness_mode=%d\n", brightness_mode);
+		printk(TPACPI_NOTICE
+			"brightness: please report to %s whether it works well "
+			"or not on your ThinkPad\n", TPACPI_MAIL);
+	}
+
 	ibm_backlight_device->props.max_brightness =
 				(tp_features.bright_16levels)? 15 : 7;
 	ibm_backlight_device->props.brightness = b & TP_EC_BACKLIGHT_LVLMSK;
-- 
GitLab


From b4f2e2ad5348063ef94aa623f6f09b52ecaf0990 Mon Sep 17 00:00:00 2001
From: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Date: Sun, 2 Aug 2009 12:34:08 +0200
Subject: [PATCH 0398/1153] parisc: Fix GOT overflow during module load on
 64bit kernel

Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Helge Deller <deller@gmx.de>
---
 arch/parisc/kernel/module.c | 50 +++++++++++++++++++++++++++++++++----
 1 file changed, 45 insertions(+), 5 deletions(-)

diff --git a/arch/parisc/kernel/module.c b/arch/parisc/kernel/module.c
index ef5caf2e6ed..61ee0eec4e6 100644
--- a/arch/parisc/kernel/module.c
+++ b/arch/parisc/kernel/module.c
@@ -86,8 +86,12 @@
  * the bottom of the table, which has a maximum signed displacement of
  * 0x3fff; however, since we're only going forward, this becomes
  * 0x1fff, and thus, since each GOT entry is 8 bytes long we can have
- * at most 1023 entries */
-#define MAX_GOTS	1023
+ * at most 1023 entries.
+ * To overcome this 14bit displacement with some kernel modules, we'll
+ * use instead the unusal 16bit displacement method (see reassemble_16a)
+ * which gives us a maximum positive displacement of 0x7fff, and as such
+ * allows us to allocate up to 4095 GOT entries. */
+#define MAX_GOTS	4095
 
 /* three functions to determine where in the module core
  * or init pieces the location is */
@@ -145,12 +149,40 @@ struct stub_entry {
 /* The reassemble_* functions prepare an immediate value for
    insertion into an opcode. pa-risc uses all sorts of weird bitfields
    in the instruction to hold the value.  */
+static inline int sign_unext(int x, int len)
+{
+	int len_ones;
+
+	len_ones = (1 << len) - 1;
+	return x & len_ones;
+}
+
+static inline int low_sign_unext(int x, int len)
+{
+	int sign, temp;
+
+	sign = (x >> (len-1)) & 1;
+	temp = sign_unext(x, len-1);
+	return (temp << 1) | sign;
+}
+
 static inline int reassemble_14(int as14)
 {
 	return (((as14 & 0x1fff) << 1) |
 		((as14 & 0x2000) >> 13));
 }
 
+static inline int reassemble_16a(int as16)
+{
+	int s, t;
+
+	/* Unusual 16-bit encoding, for wide mode only.  */
+	t = (as16 << 1) & 0xffff;
+	s = (as16 & 0x8000);
+	return (t ^ s ^ (s >> 1)) | (s >> 15);
+}
+
+
 static inline int reassemble_17(int as17)
 {
 	return (((as17 & 0x10000) >> 16) |
@@ -407,6 +439,7 @@ static Elf_Addr get_stub(struct module *me, unsigned long value, long addend,
 	enum elf_stub_type stub_type, Elf_Addr loc0, unsigned int targetsec)
 {
 	struct stub_entry *stub;
+	int __maybe_unused d;
 
 	/* initialize stub_offset to point in front of the section */
 	if (!me->arch.section[targetsec].stub_offset) {
@@ -460,12 +493,19 @@ static Elf_Addr get_stub(struct module *me, unsigned long value, long addend,
  */
 	switch (stub_type) {
 	case ELF_STUB_GOT:
-		stub->insns[0] = 0x537b0000;	/* ldd 0(%dp),%dp	*/
+		d = get_got(me, value, addend);
+		if (d <= 15) {
+			/* Format 5 */
+			stub->insns[0] = 0x0f6010db; /* ldd 0(%dp),%dp	*/
+			stub->insns[0] |= low_sign_unext(d, 5) << 16;
+		} else {
+			/* Format 3 */
+			stub->insns[0] = 0x537b0000; /* ldd 0(%dp),%dp	*/
+			stub->insns[0] |= reassemble_16a(d);
+		}
 		stub->insns[1] = 0x53610020;	/* ldd 10(%dp),%r1	*/
 		stub->insns[2] = 0xe820d000;	/* bve (%r1)		*/
 		stub->insns[3] = 0x537b0030;	/* ldd 18(%dp),%dp	*/
-
-		stub->insns[0] |= reassemble_14(get_got(me, value, addend) & 0x3fff);
 		break;
 	case ELF_STUB_MILLI:
 		stub->insns[0] = 0x20200000;	/* ldil 0,%r1		*/
-- 
GitLab


From 447c233da4d109c6194fefd69e5185cbc93cc062 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Sun, 2 Aug 2009 08:02:28 +0000
Subject: [PATCH 0399/1153] parisc: Fix read buffer overflow in pdc_stable
 driver

Check whether index is within bounds before testing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
---
 drivers/parisc/pdc_stable.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/parisc/pdc_stable.c b/drivers/parisc/pdc_stable.c
index f9f9a5f1bbd..13a64bc081b 100644
--- a/drivers/parisc/pdc_stable.c
+++ b/drivers/parisc/pdc_stable.c
@@ -370,7 +370,7 @@ pdcspath_layer_read(struct pdcspath_entry *entry, char *buf)
 	if (!i)	/* entry is not ready */
 		return -ENODATA;
 	
-	for (i = 0; devpath->layers[i] && (likely(i < 6)); i++)
+	for (i = 0; i < 6 && devpath->layers[i]; i++)
 		out += sprintf(out, "%u ", devpath->layers[i]);
 
 	out += sprintf(out, "\n");
-- 
GitLab


From 450d6e306b4717bfae11218a02648509baf04ce1 Mon Sep 17 00:00:00 2001
From: Stoyan Gaydarov <sgayda2@uiuc.edu>
Date: Thu, 30 Jul 2009 10:25:19 +0000
Subject: [PATCH 0400/1153] parisc: fixed faulty check in lba_pci

This patche fixes a spelling error that has resulted from copy and pasting.
The location of the error was found using a semantic patch but the semantic
patch was not trying to find these errors. After looking things over it
seemed logical that this change was needed.

Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Helge Deller <deller@gmx.de>
---
 drivers/parisc/lba_pci.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/parisc/lba_pci.c b/drivers/parisc/lba_pci.c
index ede614616f8..3aeb3279c92 100644
--- a/drivers/parisc/lba_pci.c
+++ b/drivers/parisc/lba_pci.c
@@ -992,7 +992,7 @@ lba_pat_resources(struct parisc_device *pa_dev, struct lba_device *lba_dev)
 		return;
 
 	io_pdc_cell = kzalloc(sizeof(pdc_pat_cell_mod_maddr_block_t), GFP_KERNEL);
-	if (!pa_pdc_cell) {
+	if (!io_pdc_cell) {
 		kfree(pa_pdc_cell);
 		return;
 	}
-- 
GitLab


From 6b4dbcd86a9d464057fcc7abe4d0574093071fcc Mon Sep 17 00:00:00 2001
From: Michael Buesch <mb@bu3sch.de>
Date: Mon, 20 Jul 2009 22:58:44 +0000
Subject: [PATCH 0401/1153] parisc: isa-eeprom - Fix loff_t usage

loff_t is a signed type. If userspace passes a negative ppos, the "count"
range check is weakened. "count"s bigger than HPEE_MAX_LENGTH will pass the check.
Also, if ppos is negative, the readb(eisa_eeprom_addr + *ppos) will poke in random
memory.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable@kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
---
 drivers/parisc/eisa_eeprom.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/parisc/eisa_eeprom.c b/drivers/parisc/eisa_eeprom.c
index 685d94e69d4..8c0b26e9b98 100644
--- a/drivers/parisc/eisa_eeprom.c
+++ b/drivers/parisc/eisa_eeprom.c
@@ -55,7 +55,7 @@ static ssize_t eisa_eeprom_read(struct file * file,
 	ssize_t ret;
 	int i;
 	
-	if (*ppos >= HPEE_MAX_LENGTH)
+	if (*ppos < 0 || *ppos >= HPEE_MAX_LENGTH)
 		return 0;
 	
 	count = *ppos + count < HPEE_MAX_LENGTH ? count : HPEE_MAX_LENGTH - *ppos;
-- 
GitLab


From 2678251b207394aa8b9d92c653c05a8b3449f1f5 Mon Sep 17 00:00:00 2001
From: John David Anglin <dave@hiauly1.hia.nrc.ca>
Date: Mon, 13 Jul 2009 01:44:37 +0000
Subject: [PATCH 0402/1153] parisc: Set correct bit in protection flags

Signed-off-by: John David Anglin <dave@hiauly1.hia.nrc.ca>
Signed-off-by: Helge Deller <deller@gmx.de>
---
 arch/parisc/kernel/entry.S | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/parisc/kernel/entry.S b/arch/parisc/kernel/entry.S
index ae3e70cd1e1..e552e547cb9 100644
--- a/arch/parisc/kernel/entry.S
+++ b/arch/parisc/kernel/entry.S
@@ -553,7 +553,7 @@
 	 * on most of those machines only handles cache transactions.
 	 */
 	extrd,u,*=	\pte,_PAGE_NO_CACHE_BIT+32,1,%r0
-	depi		1,12,1,\prot
+	depdi		1,12,1,\prot
 
 	/* Drop prot bits and convert to page addr for iitlbt and idtlbt */
 	convert_for_tlb_insert20 \pte
-- 
GitLab


From b10ff54f9f58adfb708b53e6e56ed3d7804ade74 Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Wed, 8 Jul 2009 15:27:20 +0000
Subject: [PATCH 0403/1153] parisc: includecheck fix for ccio-dma.c

fix the following 'make includecheck' warning:

  drivers/parisc/ccio-dma.c: linux/proc_fs.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
---
 drivers/parisc/ccio-dma.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/parisc/ccio-dma.c b/drivers/parisc/ccio-dma.c
index 0f0e0b919ef..a45b0c0d574 100644
--- a/drivers/parisc/ccio-dma.c
+++ b/drivers/parisc/ccio-dma.c
@@ -70,7 +70,6 @@
 #undef CCIO_COLLECT_STATS
 #endif
 
-#include <linux/proc_fs.h>
 #include <asm/runway.h>		/* for proc_runway_root */
 
 #ifdef DEBUG_CCIO_INIT
-- 
GitLab


From 470a1396c25c27b4aff08b14d5c9cd9b3da15e09 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Wed, 29 Jul 2009 10:50:09 +0200
Subject: [PATCH 0404/1153] tracing, perf_counter: Add help text to
 CONFIG_EVENT_PROFILE

Explain what tracepoint profiling sources are about.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Jeff Garzik <jeff@garzik.org>
LKML-Reference: <1248856508.6987.3041.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 init/Kconfig | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/init/Kconfig b/init/Kconfig
index cb2c0927022..823ee0a2d2a 100644
--- a/init/Kconfig
+++ b/init/Kconfig
@@ -961,9 +961,17 @@ config PERF_COUNTERS
 	  Say Y if unsure.
 
 config EVENT_PROFILE
-	bool "Tracepoint profile sources"
+	bool "Tracepoint profiling sources"
 	depends on PERF_COUNTERS && EVENT_TRACING
 	default y
+	help
+	 Allow the use of tracepoints as software performance counters.
+
+	 When this is enabled, you can create perf counters based on
+	 tracepoints using PERF_TYPE_TRACEPOINT and the tracepoint ID
+	 found in debugfs://tracing/events/*/*/id. (The -e/--events
+	 option to the perf tool can parse and interpret symbolic
+	 tracepoints, in the subsystem:tracepoint_name format.)
 
 endmenu
 
-- 
GitLab


From e53c0994709166b111fbe9162d1a16ece7dfc45b Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Fri, 24 Jul 2009 14:42:10 +0200
Subject: [PATCH 0405/1153] perf_counter: Collapse inherit on read()

Currently the counter value returned by read() is the value of
the parent counter, to which child counters are only fed back
on child exit.

Thus read() can return rather erratic (and meaningless) numbers
depending on the state of the child processes.

Change this by always iterating the full child hierarchy on
read() and sum all counters.

Suggested-by: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 95093104195..48471d75ae0 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -1688,6 +1688,18 @@ static int perf_release(struct inode *inode, struct file *file)
 	return 0;
 }
 
+static u64 perf_counter_read_tree(struct perf_counter *counter)
+{
+	struct perf_counter *child;
+	u64 total = 0;
+
+	total += perf_counter_read(counter);
+	list_for_each_entry(child, &counter->child_list, child_list)
+		total += perf_counter_read(child);
+
+	return total;
+}
+
 /*
  * Read the performance counter - simple non blocking version for now
  */
@@ -1707,7 +1719,7 @@ perf_read_hw(struct perf_counter *counter, char __user *buf, size_t count)
 
 	WARN_ON_ONCE(counter->ctx->parent_ctx);
 	mutex_lock(&counter->child_mutex);
-	values[0] = perf_counter_read(counter);
+	values[0] = perf_counter_read_tree(counter);
 	n = 1;
 	if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_ENABLED)
 		values[n++] = counter->total_time_enabled +
-- 
GitLab


From 9f498cc5be7e013d8d6e4c616980ed0ffc8680d2 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Thu, 23 Jul 2009 14:46:33 +0200
Subject: [PATCH 0406/1153] perf_counter: Full task tracing

In order to be able to distinguish between no samples due to
inactivity and no samples due to task ended, Arjan asked for
PERF_EVENT_EXIT events. This is useful to the boot delay
instrumentation (bootchart) app.

This patch changes the PERF_EVENT_FORK to be emitted on every
clone, and adds PERF_EVENT_EXIT to be emitted on task exit,
after the task's counters have been closed.

This task tracing is controlled through: attr.comm || attr.mmap
and through the new attr.task field.

Suggested-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
[ cleaned up perf_counter.h a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 include/linux/perf_counter.h | 13 +++++-
 kernel/fork.c                |  4 +-
 kernel/perf_counter.c        | 87 ++++++++++++++++++++++++------------
 3 files changed, 71 insertions(+), 33 deletions(-)

diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h
index bd15d7a5f5c..e604e6ef72d 100644
--- a/include/linux/perf_counter.h
+++ b/include/linux/perf_counter.h
@@ -181,8 +181,9 @@ struct perf_counter_attr {
 				freq           :  1, /* use freq, not period  */
 				inherit_stat   :  1, /* per task counts       */
 				enable_on_exec :  1, /* next exec enables     */
+				task           :  1, /* trace fork/exit       */
 
-				__reserved_1   : 51;
+				__reserved_1   : 50;
 
 	__u32			wakeup_events;	/* wakeup every n events */
 	__u32			__reserved_2;
@@ -308,6 +309,15 @@ enum perf_event_type {
 	 */
 	PERF_EVENT_COMM			= 3,
 
+	/*
+	 * struct {
+	 *	struct perf_event_header	header;
+	 *	u32				pid, ppid;
+	 *	u32				tid, ptid;
+	 * };
+	 */
+	PERF_EVENT_EXIT			= 4,
+
 	/*
 	 * struct {
 	 *	struct perf_event_header	header;
@@ -323,6 +333,7 @@ enum perf_event_type {
 	 * struct {
 	 *	struct perf_event_header	header;
 	 *	u32				pid, ppid;
+	 *	u32				tid, ptid;
 	 * };
 	 */
 	PERF_EVENT_FORK			= 7,
diff --git a/kernel/fork.c b/kernel/fork.c
index 29b532e718f..466531eb92c 100644
--- a/kernel/fork.c
+++ b/kernel/fork.c
@@ -1269,6 +1269,7 @@ static struct task_struct *copy_process(unsigned long clone_flags,
 	write_unlock_irq(&tasklist_lock);
 	proc_fork_connector(p);
 	cgroup_post_fork(p);
+	perf_counter_fork(p);
 	return p;
 
 bad_fork_free_pid:
@@ -1410,9 +1411,6 @@ long do_fork(unsigned long clone_flags,
 			init_completion(&vfork);
 		}
 
-		if (!(clone_flags & CLONE_THREAD))
-			perf_counter_fork(p);
-
 		audit_finish_fork(p);
 		tracehook_report_clone(regs, clone_flags, nr, p);
 
diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 48471d75ae0..199ed477131 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -42,6 +42,7 @@ static int perf_overcommit __read_mostly = 1;
 static atomic_t nr_counters __read_mostly;
 static atomic_t nr_mmap_counters __read_mostly;
 static atomic_t nr_comm_counters __read_mostly;
+static atomic_t nr_task_counters __read_mostly;
 
 /*
  * perf counter paranoia level:
@@ -1654,6 +1655,8 @@ static void free_counter(struct perf_counter *counter)
 			atomic_dec(&nr_mmap_counters);
 		if (counter->attr.comm)
 			atomic_dec(&nr_comm_counters);
+		if (counter->attr.task)
+			atomic_dec(&nr_task_counters);
 	}
 
 	if (counter->destroy)
@@ -2831,10 +2834,12 @@ perf_counter_read_event(struct perf_counter *counter,
 }
 
 /*
- * fork tracking
+ * task tracking -- fork/exit
+ *
+ * enabled by: attr.comm | attr.mmap | attr.task
  */
 
-struct perf_fork_event {
+struct perf_task_event {
 	struct task_struct	*task;
 
 	struct {
@@ -2842,37 +2847,42 @@ struct perf_fork_event {
 
 		u32				pid;
 		u32				ppid;
+		u32				tid;
+		u32				ptid;
 	} event;
 };
 
-static void perf_counter_fork_output(struct perf_counter *counter,
-				     struct perf_fork_event *fork_event)
+static void perf_counter_task_output(struct perf_counter *counter,
+				     struct perf_task_event *task_event)
 {
 	struct perf_output_handle handle;
-	int size = fork_event->event.header.size;
-	struct task_struct *task = fork_event->task;
+	int size = task_event->event.header.size;
+	struct task_struct *task = task_event->task;
 	int ret = perf_output_begin(&handle, counter, size, 0, 0);
 
 	if (ret)
 		return;
 
-	fork_event->event.pid = perf_counter_pid(counter, task);
-	fork_event->event.ppid = perf_counter_pid(counter, task->real_parent);
+	task_event->event.pid = perf_counter_pid(counter, task);
+	task_event->event.ppid = perf_counter_pid(counter, task->real_parent);
 
-	perf_output_put(&handle, fork_event->event);
+	task_event->event.tid = perf_counter_tid(counter, task);
+	task_event->event.ptid = perf_counter_tid(counter, task->real_parent);
+
+	perf_output_put(&handle, task_event->event);
 	perf_output_end(&handle);
 }
 
-static int perf_counter_fork_match(struct perf_counter *counter)
+static int perf_counter_task_match(struct perf_counter *counter)
 {
-	if (counter->attr.comm || counter->attr.mmap)
+	if (counter->attr.comm || counter->attr.mmap || counter->attr.task)
 		return 1;
 
 	return 0;
 }
 
-static void perf_counter_fork_ctx(struct perf_counter_context *ctx,
-				  struct perf_fork_event *fork_event)
+static void perf_counter_task_ctx(struct perf_counter_context *ctx,
+				  struct perf_task_event *task_event)
 {
 	struct perf_counter *counter;
 
@@ -2881,19 +2891,19 @@ static void perf_counter_fork_ctx(struct perf_counter_context *ctx,
 
 	rcu_read_lock();
 	list_for_each_entry_rcu(counter, &ctx->event_list, event_entry) {
-		if (perf_counter_fork_match(counter))
-			perf_counter_fork_output(counter, fork_event);
+		if (perf_counter_task_match(counter))
+			perf_counter_task_output(counter, task_event);
 	}
 	rcu_read_unlock();
 }
 
-static void perf_counter_fork_event(struct perf_fork_event *fork_event)
+static void perf_counter_task_event(struct perf_task_event *task_event)
 {
 	struct perf_cpu_context *cpuctx;
 	struct perf_counter_context *ctx;
 
 	cpuctx = &get_cpu_var(perf_cpu_context);
-	perf_counter_fork_ctx(&cpuctx->ctx, fork_event);
+	perf_counter_task_ctx(&cpuctx->ctx, task_event);
 	put_cpu_var(perf_cpu_context);
 
 	rcu_read_lock();
@@ -2903,32 +2913,40 @@ static void perf_counter_fork_event(struct perf_fork_event *fork_event)
 	 */
 	ctx = rcu_dereference(current->perf_counter_ctxp);
 	if (ctx)
-		perf_counter_fork_ctx(ctx, fork_event);
+		perf_counter_task_ctx(ctx, task_event);
 	rcu_read_unlock();
 }
 
-void perf_counter_fork(struct task_struct *task)
+static void perf_counter_task(struct task_struct *task, int new)
 {
-	struct perf_fork_event fork_event;
+	struct perf_task_event task_event;
 
 	if (!atomic_read(&nr_comm_counters) &&
-	    !atomic_read(&nr_mmap_counters))
+	    !atomic_read(&nr_mmap_counters) &&
+	    !atomic_read(&nr_task_counters))
 		return;
 
-	fork_event = (struct perf_fork_event){
+	task_event = (struct perf_task_event){
 		.task	= task,
 		.event  = {
 			.header = {
-				.type = PERF_EVENT_FORK,
+				.type = new ? PERF_EVENT_FORK : PERF_EVENT_EXIT,
 				.misc = 0,
-				.size = sizeof(fork_event.event),
+				.size = sizeof(task_event.event),
 			},
 			/* .pid  */
 			/* .ppid */
+			/* .tid  */
+			/* .ptid */
 		},
 	};
 
-	perf_counter_fork_event(&fork_event);
+	perf_counter_task_event(&task_event);
+}
+
+void perf_counter_fork(struct task_struct *task)
+{
+	perf_counter_task(task, 1);
 }
 
 /*
@@ -3887,6 +3905,8 @@ done:
 			atomic_inc(&nr_mmap_counters);
 		if (counter->attr.comm)
 			atomic_inc(&nr_comm_counters);
+		if (counter->attr.task)
+			atomic_inc(&nr_task_counters);
 	}
 
 	return counter;
@@ -4248,8 +4268,10 @@ void perf_counter_exit_task(struct task_struct *child)
 	struct perf_counter_context *child_ctx;
 	unsigned long flags;
 
-	if (likely(!child->perf_counter_ctxp))
+	if (likely(!child->perf_counter_ctxp)) {
+		perf_counter_task(child, 0);
 		return;
+	}
 
 	local_irq_save(flags);
 	/*
@@ -4267,15 +4289,22 @@ void perf_counter_exit_task(struct task_struct *child)
 	 * incremented the context's refcount before we do put_ctx below.
 	 */
 	spin_lock(&child_ctx->lock);
-	child->perf_counter_ctxp = NULL;
 	/*
 	 * If this context is a clone; unclone it so it can't get
 	 * swapped to another process while we're removing all
 	 * the counters from it.
 	 */
 	unclone_ctx(child_ctx);
-	spin_unlock(&child_ctx->lock);
-	local_irq_restore(flags);
+	spin_unlock_irqrestore(&child_ctx->lock, flags);
+
+	/*
+	 * Report the task dead after unscheduling the counters so that we
+	 * won't get any samples after PERF_EVENT_EXIT. We can however still
+	 * get a few PERF_EVENT_READ events.
+	 */
+	perf_counter_task(child, 0);
+
+	child->perf_counter_ctxp = NULL;
 
 	/*
 	 * We can recurse on the same lock type through:
-- 
GitLab


From 27d028de64bd7e1f8e72bdeae6b0586939574fcb Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Thu, 23 Jul 2009 16:52:41 +0200
Subject: [PATCH 0407/1153] perf report: Update for the new FORK/EXIT events

Since FORK is now also issued for threads, detect those by
comparing the parent and child PID.

Teach it about EXIT events and ignore them.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-report.c | 22 ++++++++++++++++++----
 1 file changed, 18 insertions(+), 4 deletions(-)

diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index b20a4b6e31b..95fd06cdaa9 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -99,6 +99,7 @@ struct comm_event {
 struct fork_event {
 	struct perf_event_header header;
 	u32 pid, ppid;
+	u32 tid, ptid;
 };
 
 struct lost_event {
@@ -1608,15 +1609,27 @@ process_comm_event(event_t *event, unsigned long offset, unsigned long head)
 }
 
 static int
-process_fork_event(event_t *event, unsigned long offset, unsigned long head)
+process_task_event(event_t *event, unsigned long offset, unsigned long head)
 {
 	struct thread *thread = threads__findnew(event->fork.pid);
 	struct thread *parent = threads__findnew(event->fork.ppid);
 
-	dprintf("%p [%p]: PERF_EVENT_FORK: %d:%d\n",
+	dprintf("%p [%p]: PERF_EVENT_%s: (%d:%d):(%d:%d)\n",
 		(void *)(offset + head),
 		(void *)(long)(event->header.size),
-		event->fork.pid, event->fork.ppid);
+		event->header.type == PERF_EVENT_FORK ? "FORK" : "EXIT",
+		event->fork.pid, event->fork.tid,
+		event->fork.ppid, event->fork.ptid);
+
+	/*
+	 * A thread clone will have the same PID for both
+	 * parent and child.
+	 */
+	if (thread == parent)
+		return 0;
+
+	if (event->header.type == PERF_EVENT_EXIT)
+		return 0;
 
 	if (!thread || !parent || thread__fork(thread, parent)) {
 		dprintf("problem processing PERF_EVENT_FORK, skipping event.\n");
@@ -1706,7 +1719,8 @@ process_event(event_t *event, unsigned long offset, unsigned long head)
 		return process_comm_event(event, offset, head);
 
 	case PERF_EVENT_FORK:
-		return process_fork_event(event, offset, head);
+	case PERF_EVENT_EXIT:
+		return process_task_event(event, offset, head);
 
 	case PERF_EVENT_LOST:
 		return process_lost_event(event, offset, head);
-- 
GitLab


From 9b30a26bf3d2c56dcb1c3afaca28b73fcd6ed405 Mon Sep 17 00:00:00 2001
From: Stoyan Gaydarov <sgayda2@uiuc.edu>
Date: Thu, 30 Jul 2009 05:25:29 -0500
Subject: [PATCH 0408/1153] perf tools: Fix faulty check

This patch fixes a spelling error that has resulted from copy
and pasting. The location of the error was found using a
semantic patch but the semantic patch was not trying to find
these errors. After looking things over it seemed logical that
this change was needed. Please review it and then include the
patch if it is in fact the correct change.

Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1248949529-20891-1-git-send-email-sgayda2@uiuc.edu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/util/symbol.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c
index 28106059bf1..b4fe0579bd6 100644
--- a/tools/perf/util/symbol.c
+++ b/tools/perf/util/symbol.c
@@ -565,7 +565,7 @@ static int dso__load_sym(struct dso *self, int fd, const char *name,
 		goto out_elf_end;
 
 	secstrs = elf_getdata(sec_strndx, NULL);
-	if (symstrs == NULL)
+	if (secstrs == NULL)
 		goto out_elf_end;
 
 	nr_syms = shdr.sh_size / shdr.sh_entsize;
-- 
GitLab


From 59b9005692d4c8b5d73cfc41aa7229f47be163a9 Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Sun, 26 Jul 2009 19:06:19 -0300
Subject: [PATCH 0409/1153] perf top: Add mwait_idle_with_hints to
 skip_symbols[]

We skip the display of idle routine related symbols because
they are typically rather erratic and confusing: they depend
on the IRQ rate or sometimes they dominate the profile if
they are polling based.

Add mwait_idle_with_hints too, this is one of the idle
routines on x86.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-top.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/tools/perf/builtin-top.c b/tools/perf/builtin-top.c
index c0a423004e1..f139f1ab933 100644
--- a/tools/perf/builtin-top.c
+++ b/tools/perf/builtin-top.c
@@ -285,6 +285,7 @@ static const char *skip_symbols[] = {
 	"enter_idle",
 	"exit_idle",
 	"mwait_idle",
+	"mwait_idle_with_hints",
 	"ppc64_runlatch_off",
 	"pseries_dedicated_idle_sleep",
 	NULL
-- 
GitLab


From e414314cce7539788dd5d2c35decad11782dd858 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Thu, 23 Jul 2009 20:13:26 +0200
Subject: [PATCH 0410/1153] sched: Fix latencytop and sleep profiling vs group
 scheduling

The latencytop and sleep accounting code assumes that any
scheduler entity represents a task, this is not so.

Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/sched_fair.c | 32 +++++++++++++++++++-------------
 1 file changed, 19 insertions(+), 13 deletions(-)

diff --git a/kernel/sched_fair.c b/kernel/sched_fair.c
index 9ffb2b2ceba..652e8bdef9a 100644
--- a/kernel/sched_fair.c
+++ b/kernel/sched_fair.c
@@ -611,9 +611,13 @@ account_entity_dequeue(struct cfs_rq *cfs_rq, struct sched_entity *se)
 static void enqueue_sleeper(struct cfs_rq *cfs_rq, struct sched_entity *se)
 {
 #ifdef CONFIG_SCHEDSTATS
+	struct task_struct *tsk = NULL;
+
+	if (entity_is_task(se))
+		tsk = task_of(se);
+
 	if (se->sleep_start) {
 		u64 delta = rq_of(cfs_rq)->clock - se->sleep_start;
-		struct task_struct *tsk = task_of(se);
 
 		if ((s64)delta < 0)
 			delta = 0;
@@ -624,11 +628,11 @@ static void enqueue_sleeper(struct cfs_rq *cfs_rq, struct sched_entity *se)
 		se->sleep_start = 0;
 		se->sum_sleep_runtime += delta;
 
-		account_scheduler_latency(tsk, delta >> 10, 1);
+		if (tsk)
+			account_scheduler_latency(tsk, delta >> 10, 1);
 	}
 	if (se->block_start) {
 		u64 delta = rq_of(cfs_rq)->clock - se->block_start;
-		struct task_struct *tsk = task_of(se);
 
 		if ((s64)delta < 0)
 			delta = 0;
@@ -639,17 +643,19 @@ static void enqueue_sleeper(struct cfs_rq *cfs_rq, struct sched_entity *se)
 		se->block_start = 0;
 		se->sum_sleep_runtime += delta;
 
-		/*
-		 * Blocking time is in units of nanosecs, so shift by 20 to
-		 * get a milliseconds-range estimation of the amount of
-		 * time that the task spent sleeping:
-		 */
-		if (unlikely(prof_on == SLEEP_PROFILING)) {
-
-			profile_hits(SLEEP_PROFILING, (void *)get_wchan(tsk),
-				     delta >> 20);
+		if (tsk) {
+			/*
+			 * Blocking time is in units of nanosecs, so shift by
+			 * 20 to get a milliseconds-range estimation of the
+			 * amount of time that the task spent sleeping:
+			 */
+			if (unlikely(prof_on == SLEEP_PROFILING)) {
+				profile_hits(SLEEP_PROFILING,
+						(void *)get_wchan(tsk),
+						delta >> 20);
+			}
+			account_scheduler_latency(tsk, delta >> 10, 0);
 		}
-		account_scheduler_latency(tsk, delta >> 10, 0);
 	}
 #endif
 }
-- 
GitLab


From 07903af152b0597d94e9b0030746b63c4664e787 Mon Sep 17 00:00:00 2001
From: Gregory Haskins <ghaskins@novell.com>
Date: Thu, 30 Jul 2009 10:57:28 -0400
Subject: [PATCH 0411/1153] sched: Fix race in cpupri introduced by cpumask_var
 changes

Background:

Several race conditions in the scheduler have cropped up
recently, which Steven and I have tracked down using ftrace.
The most recent one turns out to be a race in how the scheduler
determines a suitable migration target for RT tasks, introduced
recently with commit:

    commit 68e74568fbe5854952355e942acca51f138096d9
    Date:   Tue Nov 25 02:35:13 2008 +1030

        sched: convert struct cpupri_vec cpumask_var_t.

The original design of cpupri allowed lockless readers to
quickly determine a best-estimate target.  Races between the
pri_active bitmap and the vec->mask were handled in the
original code because we would detect and return "0" when this
occured.  The design was predicated on the *effective*
atomicity (*) of caching the result of cpus_and() between the
cpus_allowed and the vec->mask.

Commit 68e74568 changed the behavior such that vec->mask is
accessed multiple times.  This introduces a subtle race, the
result of which means we can have a result that returns "1",
but with an empty bitmap.

*) yes, we know cpus_and() is not a locked operator across the
   entire composite array, but it is implicitly atomic on a
   per-word basis which is all the design required to work.

Implementation:

Rather than forgoing the lockless design, or reverting to a
stack-based cpumask_t, we simply check for when the race has
been encountered and continue processing in the event that the
race is hit.  This renders the removal race as if the priority
bit had been atomically cleared as well, and allows the
algorithm to execute correctly.

Signed-off-by: Gregory Haskins <ghaskins@novell.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090730145728.25226.92769.stgit@dev.haskins.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/sched_cpupri.c | 15 ++++++++++++++-
 1 file changed, 14 insertions(+), 1 deletion(-)

diff --git a/kernel/sched_cpupri.c b/kernel/sched_cpupri.c
index e6c251790dd..d014efbf947 100644
--- a/kernel/sched_cpupri.c
+++ b/kernel/sched_cpupri.c
@@ -81,8 +81,21 @@ int cpupri_find(struct cpupri *cp, struct task_struct *p,
 		if (cpumask_any_and(&p->cpus_allowed, vec->mask) >= nr_cpu_ids)
 			continue;
 
-		if (lowest_mask)
+		if (lowest_mask) {
 			cpumask_and(lowest_mask, &p->cpus_allowed, vec->mask);
+
+			/*
+			 * We have to ensure that we have at least one bit
+			 * still set in the array, since the map could have
+			 * been concurrently emptied between the first and
+			 * second reads of vec->mask.  If we hit this
+			 * condition, simply act as though we never hit this
+			 * priority level and continue on.
+			 */
+			if (cpumask_any(lowest_mask) >= nr_cpu_ids)
+				continue;
+		}
+
 		return 1;
 	}
 
-- 
GitLab


From c6fe6b0783a8fd923d11dd0388cbd561ff15bdf1 Mon Sep 17 00:00:00 2001
From: Helge Deller <deller@gmx.de>
Date: Sun, 2 Aug 2009 15:13:29 +0200
Subject: [PATCH 0412/1153] parisc: hp_sdc_mlc.c - check return value of
 down_trylock()

Signed-off-by: Helge Deller <deller@gmx.de>
---
 drivers/input/serio/hp_sdc_mlc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/input/serio/hp_sdc_mlc.c b/drivers/input/serio/hp_sdc_mlc.c
index b587e2d576a..820e51673b2 100644
--- a/drivers/input/serio/hp_sdc_mlc.c
+++ b/drivers/input/serio/hp_sdc_mlc.c
@@ -296,7 +296,7 @@ static void hp_sdc_mlc_out(hil_mlc *mlc)
 	priv->tseq[3] = 0;
 	if (mlc->opacket & HIL_CTRL_APE) {
 		priv->tseq[3] |= HP_SDC_LPC_APE_IPF;
-		down_trylock(&mlc->csem);
+		BUG_ON(down_trylock(&mlc->csem));
 	}
  enqueue:
 	hp_sdc_enqueue_transaction(&priv->trans);
-- 
GitLab


From 1e0deabd35f210f22c03cc734a0335c07ae71ff3 Mon Sep 17 00:00:00 2001
From: Helge Deller <deller@gmx.de>
Date: Sun, 2 Aug 2009 15:17:37 +0200
Subject: [PATCH 0413/1153] parisc: dino.c - check return value of
 pci_assign_resource()

Signed-off-by: Helge Deller <deller@gmx.de>
---
 drivers/parisc/dino.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/parisc/dino.c b/drivers/parisc/dino.c
index c590974e981..d69bde6a234 100644
--- a/drivers/parisc/dino.c
+++ b/drivers/parisc/dino.c
@@ -614,7 +614,7 @@ dino_fixup_bus(struct pci_bus *bus)
 			    dev_name(&bus->self->dev), i,
 			    bus->self->resource[i].start,
 			    bus->self->resource[i].end);
-			pci_assign_resource(bus->self, i);
+			WARN_ON(pci_assign_resource(bus->self, i));
 			DBG("DEBUG %s after assign %d [0x%lx,0x%lx]\n",
 			    dev_name(&bus->self->dev), i,
 			    bus->self->resource[i].start,
-- 
GitLab


From 01a261e09a21e0ba342d3907a79cf5c78ee3f37a Mon Sep 17 00:00:00 2001
From: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Date: Sun, 2 Aug 2009 17:45:55 +0900
Subject: [PATCH 0414/1153] nilfs2: fix missing unlock in error path of
 nilfs_mdt_write_page

This adds a missing unlock of nilfs->ns_writer_mutex in
nilfs_mdt_write_page() function.

Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
---
 fs/nilfs2/mdt.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/fs/nilfs2/mdt.c b/fs/nilfs2/mdt.c
index 3d3ddb3f517..2dfd47714ae 100644
--- a/fs/nilfs2/mdt.c
+++ b/fs/nilfs2/mdt.c
@@ -412,8 +412,10 @@ nilfs_mdt_write_page(struct page *page, struct writeback_control *wbc)
 		return 0; /* Do not request flush for shadow page cache */
 	if (!sb) {
 		writer = nilfs_get_writer(NILFS_MDT(inode)->mi_nilfs);
-		if (!writer)
+		if (!writer) {
+			nilfs_put_writer(NILFS_MDT(inode)->mi_nilfs);
 			return -EROFS;
+		}
 		sb = writer->s_super;
 	}
 
-- 
GitLab


From 1a1dba32412c15c51d5fc0b9efadd2ea310356d7 Mon Sep 17 00:00:00 2001
From: Helge Deller <deller@gmx.de>
Date: Sun, 2 Aug 2009 15:26:51 +0200
Subject: [PATCH 0415/1153] parisc: sticore.c - check return values

Signed-off-by: Helge Deller <deller@gmx.de>
---
 drivers/video/console/sticore.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/video/console/sticore.c b/drivers/video/console/sticore.c
index ef7870f5ea0..857b3668b3b 100644
--- a/drivers/video/console/sticore.c
+++ b/drivers/video/console/sticore.c
@@ -957,9 +957,14 @@ static int __devinit sticore_pci_init(struct pci_dev *pd,
 #ifdef CONFIG_PCI
 	unsigned long fb_base, rom_base;
 	unsigned int fb_len, rom_len;
+	int err;
 	struct sti_struct *sti;
 	
-	pci_enable_device(pd);
+	err = pci_enable_device(pd);
+	if (err < 0) {
+		dev_err(&pd->dev, "Cannot enable PCI device\n");
+		return err;
+	}
 
 	fb_base = pci_resource_start(pd, 0);
 	fb_len = pci_resource_len(pd, 0);
@@ -1048,7 +1053,7 @@ static void __devinit sti_init_roms(void)
 
 	/* Register drivers for native & PCI cards */
 	register_parisc_driver(&pa_sti_driver);
-	pci_register_driver(&pci_sti_driver);
+	WARN_ON(pci_register_driver(&pci_sti_driver));
 
 	/* if we didn't find the given default sti, take the first one */
 	if (!default_sti)
-- 
GitLab


From c43962321e8af5309dd3ffcd78743c89581265e5 Mon Sep 17 00:00:00 2001
From: Helge Deller <deller@gmx.de>
Date: Sun, 2 Aug 2009 15:35:43 +0200
Subject: [PATCH 0416/1153] parisc: parisc-agp.c - use correct page_mask
 function

Fix those compiler warnings, which indeed point to a bug:
drivers/char/agp/parisc-agp.c:228: warning: initialization from incompatible pointer type
drivers/char/agp/parisc-agp.c:201: warning: 'parisc_agp_page_mask_memory' defined but not used

Signed-off-by: Helge Deller <deller@gmx.de>
---
 drivers/char/agp/parisc-agp.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/char/agp/parisc-agp.c b/drivers/char/agp/parisc-agp.c
index f4bb43fb801..e077701ae3d 100644
--- a/drivers/char/agp/parisc-agp.c
+++ b/drivers/char/agp/parisc-agp.c
@@ -225,7 +225,7 @@ static const struct agp_bridge_driver parisc_agp_driver = {
 	.configure		= parisc_agp_configure,
 	.fetch_size		= parisc_agp_fetch_size,
 	.tlb_flush		= parisc_agp_tlbflush,
-	.mask_memory		= parisc_agp_mask_memory,
+	.mask_memory		= parisc_agp_page_mask_memory,
 	.masks			= parisc_agp_masks,
 	.agp_enable		= parisc_agp_enable,
 	.cache_flush		= global_cache_flush,
-- 
GitLab


From cae5a39f34d52c46ca49edfc3f297656a0fd60b7 Mon Sep 17 00:00:00 2001
From: Helge Deller <deller@gmx.de>
Date: Sun, 2 Aug 2009 15:42:39 +0200
Subject: [PATCH 0417/1153] parisc: hppb.c - fix printk format strings

Fix those warnings:
drivers/parisc/hppb.c: In function 'hppb_probe':
drivers/parisc/hppb.c:65: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/parisc/hppb.c:77: warning: format '%08x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'

Signed-off-by: Helge Deller <deller@gmx.de>
---
 drivers/parisc/hppb.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/parisc/hppb.c b/drivers/parisc/hppb.c
index 13856415b43..815db175d42 100644
--- a/drivers/parisc/hppb.c
+++ b/drivers/parisc/hppb.c
@@ -62,7 +62,8 @@ static int hppb_probe(struct parisc_device *dev)
 		}
 		card = card->next;
 	}
-        printk(KERN_INFO "Found GeckoBoa at 0x%x\n", dev->hpa.start);
+	printk(KERN_INFO "Found GeckoBoa at 0x%llx\n",
+			(unsigned long long) dev->hpa.start);
 
 	card->hpa = dev->hpa.start;
 	card->mmio_region.name = "HP-PB Bus";
@@ -73,8 +74,10 @@ static int hppb_probe(struct parisc_device *dev)
 
 	status = ccio_request_resource(dev, &card->mmio_region);
 	if(status < 0) {
-		printk(KERN_ERR "%s: failed to claim HP-PB bus space (%08x, %08x)\n",
-			__FILE__, card->mmio_region.start, card->mmio_region.end);
+		printk(KERN_ERR "%s: failed to claim HP-PB "
+			"bus space (0x%08llx, 0x%08llx)\n",
+			__FILE__, (unsigned long long) card->mmio_region.start,
+			(unsigned long long) card->mmio_region.end);
 	}
 
         return 0;
-- 
GitLab


From d0006f3281c920fbfead0f5035c62ec8053f980a Mon Sep 17 00:00:00 2001
From: Len Brown <len.brown@intel.com>
Date: Thu, 30 Jul 2009 16:00:53 -0400
Subject: [PATCH 0418/1153] ACPI: root-only read protection on
 /sys/firmware/acpi/tables/*

they were world readable.

Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/acpi/system.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/acpi/system.c b/drivers/acpi/system.c
index 0944daec064..9c61ab2177c 100644
--- a/drivers/acpi/system.c
+++ b/drivers/acpi/system.c
@@ -121,7 +121,7 @@ static void acpi_table_attr_init(struct acpi_table_attr *table_attr,
 	table_attr->attr.size = 0;
 	table_attr->attr.read = acpi_table_show;
 	table_attr->attr.attr.name = table_attr->name;
-	table_attr->attr.attr.mode = 0444;
+	table_attr->attr.attr.mode = 0400;
 
 	return;
 }
-- 
GitLab


From 74b5820808215f65b70b05a099d6d3c969b82689 Mon Sep 17 00:00:00 2001
From: Bjorn Helgaas <bjorn.helgaas@hp.com>
Date: Wed, 29 Jul 2009 15:54:25 -0600
Subject: [PATCH 0419/1153] ACPI: bind workqueues to CPU 0 to avoid SMI
 corruption

On some machines, a software-initiated SMI causes corruption unless the
SMI runs on CPU 0.  An SMI can be initiated by any AML, but typically it's
done in GPE-related methods that are run via workqueues, so we can avoid
the known corruption cases by binding the workqueues to CPU 0.

References:
    http://bugzilla.kernel.org/show_bug.cgi?id=13751
    https://bugs.launchpad.net/bugs/157171
    https://bugs.launchpad.net/bugs/157691

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/acpi/osl.c | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)

diff --git a/drivers/acpi/osl.c b/drivers/acpi/osl.c
index 71670719d61..5691f165a95 100644
--- a/drivers/acpi/osl.c
+++ b/drivers/acpi/osl.c
@@ -189,11 +189,36 @@ acpi_status __init acpi_os_initialize(void)
 	return AE_OK;
 }
 
+static void bind_to_cpu0(struct work_struct *work)
+{
+	set_cpus_allowed(current, cpumask_of_cpu(0));
+	kfree(work);
+}
+
+static void bind_workqueue(struct workqueue_struct *wq)
+{
+	struct work_struct *work;
+
+	work = kzalloc(sizeof(struct work_struct), GFP_KERNEL);
+	INIT_WORK(work, bind_to_cpu0);
+	queue_work(wq, work);
+}
+
 acpi_status acpi_os_initialize1(void)
 {
+	/*
+	 * On some machines, a software-initiated SMI causes corruption unless
+	 * the SMI runs on CPU 0.  An SMI can be initiated by any AML, but
+	 * typically it's done in GPE-related methods that are run via
+	 * workqueues, so we can avoid the known corruption cases by binding
+	 * the workqueues to CPU 0.
+	 */
 	kacpid_wq = create_singlethread_workqueue("kacpid");
+	bind_workqueue(kacpid_wq);
 	kacpi_notify_wq = create_singlethread_workqueue("kacpi_notify");
+	bind_workqueue(kacpi_notify_wq);
 	kacpi_hotplug_wq = create_singlethread_workqueue("kacpi_hotplug");
+	bind_workqueue(kacpi_hotplug_wq);
 	BUG_ON(!kacpid_wq);
 	BUG_ON(!kacpi_notify_wq);
 	BUG_ON(!kacpi_hotplug_wq);
-- 
GitLab


From aa7b2b2e973874df99a45b31adbed5978b46be1f Mon Sep 17 00:00:00 2001
From: Zhao Yakui <yakui.zhao@intel.com>
Date: Fri, 3 Jul 2009 10:49:03 +0800
Subject: [PATCH 0420/1153] ACPI: Don't treat generic error as ACPI error code
 in acpi memory hotplug driver

Don't treat the generic error as ACPI error code. Otherwise when the generic
code is returned, it will complain the following warning messag:
   >ACPI Exception (acpi_memhotplug-0171): UNKNOWN_STATUS_CODE,
		Cannot get acpi bus device [20080609]
   >ACPI: Cannot find driver data
   > ACPI Error (utglobal-0127): Unknown exception code: 0xFFFFFFED [20080609]
   > Pid: 85, comm: kacpi_notify Not tainted 2.6.27.19-5-default #1
     Call Trace:
     [<ffffffff8020da29>] show_trace_log_lvl+0x41/0x58
     [<ffffffff8049a3da>] dump_stack+0x69/0x6f
    .....

At the same time when the generic error code is returned, the ACPI_EXCEPTION
is replaced by the printk.

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/acpi/acpi_memhotplug.c | 16 ++++++++++------
 1 file changed, 10 insertions(+), 6 deletions(-)

diff --git a/drivers/acpi/acpi_memhotplug.c b/drivers/acpi/acpi_memhotplug.c
index 7a0f4aa4fa1..37cbe72d17e 100644
--- a/drivers/acpi/acpi_memhotplug.c
+++ b/drivers/acpi/acpi_memhotplug.c
@@ -38,6 +38,9 @@
 
 #define _COMPONENT		ACPI_MEMORY_DEVICE_COMPONENT
 
+#undef PREFIX
+#define 	PREFIX		"ACPI:memory_hp:"
+
 ACPI_MODULE_NAME("acpi_memhotplug");
 MODULE_AUTHOR("Naveen B S <naveen.b.s@intel.com>");
 MODULE_DESCRIPTION("Hotplug Mem Driver");
@@ -153,6 +156,7 @@ acpi_memory_get_device(acpi_handle handle,
 	acpi_handle phandle;
 	struct acpi_device *device = NULL;
 	struct acpi_device *pdevice = NULL;
+	int result;
 
 
 	if (!acpi_bus_get_device(handle, &device) && device)
@@ -165,9 +169,9 @@ acpi_memory_get_device(acpi_handle handle,
 	}
 
 	/* Get the parent device */
-	status = acpi_bus_get_device(phandle, &pdevice);
-	if (ACPI_FAILURE(status)) {
-		ACPI_EXCEPTION((AE_INFO, status, "Cannot get acpi bus device"));
+	result = acpi_bus_get_device(phandle, &pdevice);
+	if (result) {
+		printk(KERN_WARNING PREFIX "Cannot get acpi bus device");
 		return -EINVAL;
 	}
 
@@ -175,9 +179,9 @@ acpi_memory_get_device(acpi_handle handle,
 	 * Now add the notified device.  This creates the acpi_device
 	 * and invokes .add function
 	 */
-	status = acpi_bus_add(&device, pdevice, handle, ACPI_BUS_TYPE_DEVICE);
-	if (ACPI_FAILURE(status)) {
-		ACPI_EXCEPTION((AE_INFO, status, "Cannot add acpi bus"));
+	result = acpi_bus_add(&device, pdevice, handle, ACPI_BUS_TYPE_DEVICE);
+	if (result) {
+		printk(KERN_WARNING PREFIX "Cannot add acpi bus");
 		return -EINVAL;
 	}
 
-- 
GitLab


From 5d2619fca753d270e63e76c9e18437b0d9bc8d75 Mon Sep 17 00:00:00 2001
From: Zhao Yakui <yakui.zhao@intel.com>
Date: Tue, 7 Jul 2009 10:56:11 +0800
Subject: [PATCH 0421/1153] ACPI: Ingore the memory block with zero block size
 in course of memory hotplug

If the memory block size is zero, ignore it and don't do the memory hotplug
flowchart. Otherwise it will complain the following warning message:
  >System RAM resource 0 - ffffffffffffffff cannot be added

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/acpi/acpi_memhotplug.c | 18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)

diff --git a/drivers/acpi/acpi_memhotplug.c b/drivers/acpi/acpi_memhotplug.c
index 37cbe72d17e..9a62224cc27 100644
--- a/drivers/acpi/acpi_memhotplug.c
+++ b/drivers/acpi/acpi_memhotplug.c
@@ -242,7 +242,12 @@ static int acpi_memory_enable_device(struct acpi_memory_device *mem_device)
 			num_enabled++;
 			continue;
 		}
-
+		/*
+		 * If the memory block size is zero, please ignore it.
+		 * Don't try to do the following memory hotplug flowchart.
+		 */
+		if (!info->length)
+			continue;
 		if (node < 0)
 			node = memory_add_physaddr_to_nid(info->start_addr);
 
@@ -257,8 +262,15 @@ static int acpi_memory_enable_device(struct acpi_memory_device *mem_device)
 		mem_device->state = MEMORY_INVALID_STATE;
 		return -EINVAL;
 	}
-
-	return result;
+	/*
+	 * Sometimes the memory device will contain several memory blocks.
+	 * When one memory block is hot-added to the system memory, it will
+	 * be regarded as a success.
+	 * Otherwise if the last memory block can't be hot-added to the system
+	 * memory, it will be failure and the memory device can't be bound with
+	 * driver.
+	 */
+	return 0;
 }
 
 static int acpi_memory_powerdown_device(struct acpi_memory_device *mem_device)
-- 
GitLab


From 7334546a52c6764df120459509b1f803a073eacc Mon Sep 17 00:00:00 2001
From: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Date: Mon, 29 Jun 2009 09:40:07 +0100
Subject: [PATCH 0422/1153] eeepc-laptop: fix hot-unplug on resume

OOPS on resume when the wireless adaptor is disabled during suspend was
introduced by "eeepc-laptop: read rfkill soft-blocked state on resume".

Unable to handle kernel NULL pointer dereference

Process s2disk
Tainted: G W
IP: klist_put

Call trace:
? klist_del
? device_del
? device_unregister
? pci_stop_dev
? pci_stop_bus
? pci_remove_device
? eeepc_rfkill_hotplug [eeepc_laptop]
? eeepc_hotk_resume [eeepc_laptop]
? acpi_device_resume
? device_resume
? hibernation_snapshot

It appears the PCI device is removed twice.  The eeepc_rfkill_hotplug()
call from the resume handler is racing against the call from the ACPI
notifier callback.  The ACPI notification is triggered by the resume
handler when it refreshes the value of CM_ASL_WLAN.

The fix is to serialize hotplug calls using a workqueue.

http://bugzilla.kernel.org/show_bug.cgi?id=13825

Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/platform/x86/eeepc-laptop.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/platform/x86/eeepc-laptop.c b/drivers/platform/x86/eeepc-laptop.c
index ec560f16d72..222ffb892f2 100644
--- a/drivers/platform/x86/eeepc-laptop.c
+++ b/drivers/platform/x86/eeepc-laptop.c
@@ -143,6 +143,7 @@ struct eeepc_hotk {
 	struct rfkill *bluetooth_rfkill;
 	struct rfkill *wwan3g_rfkill;
 	struct hotplug_slot *hotplug_slot;
+	struct work_struct hotplug_work;
 };
 
 /* The actual device the driver binds to */
@@ -660,7 +661,7 @@ static int eeepc_get_adapter_status(struct hotplug_slot *hotplug_slot,
 	return 0;
 }
 
-static void eeepc_rfkill_hotplug(void)
+static void eeepc_hotplug_work(struct work_struct *work)
 {
 	struct pci_dev *dev;
 	struct pci_bus *bus = pci_find_bus(0, 1);
@@ -701,7 +702,7 @@ static void eeepc_rfkill_notify(acpi_handle handle, u32 event, void *data)
 	if (event != ACPI_NOTIFY_BUS_CHECK)
 		return;
 
-	eeepc_rfkill_hotplug();
+	schedule_work(&ehotk->hotplug_work);
 }
 
 static void eeepc_hotk_notify(struct acpi_device *device, u32 event)
@@ -892,7 +893,7 @@ static int eeepc_hotk_resume(struct acpi_device *device)
 
 		rfkill_set_sw_state(ehotk->wlan_rfkill, wlan != 1);
 
-		eeepc_rfkill_hotplug();
+		schedule_work(&ehotk->hotplug_work);
 	}
 
 	if (ehotk->bluetooth_rfkill)
@@ -1093,6 +1094,8 @@ static int eeepc_rfkill_init(struct device *dev)
 {
 	int result = 0;
 
+	INIT_WORK(&ehotk->hotplug_work, eeepc_hotplug_work);
+
 	eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P6");
 	eeepc_register_rfkill_notifier("\\_SB.PCI0.P0P7");
 
-- 
GitLab


From a53a8b56827cc429c6d9f861ad558beeb5f6103f Mon Sep 17 00:00:00 2001
From: Ben McKeegan <ben@netservers.co.uk>
Date: Tue, 28 Jul 2009 07:43:57 +0000
Subject: [PATCH 0423/1153] ppp: fix lost fragments in ppp_mp_explode()
 (resubmit)

This patch fixes the corner cases where the sum of MTU of the free
channels (adjusted for fragmentation overheads) is less than the MTU
of PPP link.  There are at least 3 situations where this case might
arise:

- some of the channels are busy

- the multilink session is running in a degraded state (i.e. with less
than its full complement of active channels)

- by design, where multilink protocol is being used to artificially
increase the effective link MTU of a single link.

Without this patch, at most 1 fragment is ever sent per free channel
for a given PPP frame and any remaining part of the PPP frame that
does not fit into those fragments is silently discarded.

This patch restores the original behaviour which was broken by commit
9c705260feea6ae329bc6b6d5f6d2ef0227eda0a 'ppp:ppp_mp_explode()
redesign'.  Once all 'free' channels have been given a fragment, an
additional fragment is queued to each available channel in turn, as many
times as necessary, until the entire PPP frame has been consumed.

Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ppp_generic.c | 34 ++++++++++++++++++----------------
 1 file changed, 18 insertions(+), 16 deletions(-)

diff --git a/drivers/net/ppp_generic.c b/drivers/net/ppp_generic.c
index 639d11bc444..cd37d739ac7 100644
--- a/drivers/net/ppp_generic.c
+++ b/drivers/net/ppp_generic.c
@@ -1384,7 +1384,7 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb)
 
 	/* create a	fragment for each channel */
 	bits = B;
-	while (nfree > 0 &&	len	> 0) {
+	while (len	> 0) {
 		list = list->next;
 		if (list ==	&ppp->channels)	{
 			i =	0;
@@ -1431,29 +1431,31 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb)
 		*otherwise divide it according to the speed
 		*of the channel we are going to transmit on
 		*/
-		if (pch->speed == 0) {
-			flen = totlen/nfree	;
-			if (nbigger > 0) {
-				flen++;
-				nbigger--;
-			}
-		} else {
-			flen = (((totfree - nzero)*(totlen + hdrlen*totfree)) /
-				((totspeed*totfree)/pch->speed)) - hdrlen;
-			if (nbigger > 0) {
-				flen += ((totfree - nzero)*pch->speed)/totspeed;
-				nbigger -= ((totfree - nzero)*pch->speed)/
+		if (nfree > 0) {
+			if (pch->speed == 0) {
+				flen = totlen/nfree	;
+				if (nbigger > 0) {
+					flen++;
+					nbigger--;
+				}
+			} else {
+				flen = (((totfree - nzero)*(totlen + hdrlen*totfree)) /
+					((totspeed*totfree)/pch->speed)) - hdrlen;
+				if (nbigger > 0) {
+					flen += ((totfree - nzero)*pch->speed)/totspeed;
+					nbigger -= ((totfree - nzero)*pch->speed)/
 							totspeed;
+				}
 			}
+			nfree--;
 		}
-		nfree--;
 
 		/*
 		 *check	if we are on the last channel or
 		 *we exceded the lenght	of the data	to
 		 *fragment
 		 */
-		if ((nfree == 0) || (flen > len))
+		if ((nfree <= 0) || (flen > len))
 			flen = len;
 		/*
 		 *it is not worth to tx on slow channels:
@@ -1467,7 +1469,7 @@ static int ppp_mp_explode(struct ppp *ppp, struct sk_buff *skb)
 			continue;
 		}
 
-		mtu	= pch->chan->mtu + 2 - hdrlen;
+		mtu	= pch->chan->mtu - hdrlen;
 		if (mtu	< 4)
 			mtu	= 4;
 		if (flen > mtu)
-- 
GitLab


From 446e72f30eca76d6f9a1a54adf84d2c6ba2831f8 Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Tue, 28 Jul 2009 03:47:39 +0000
Subject: [PATCH 0424/1153] pppol2tp: calls unregister_pernet_gen_device() at
 unload time

Failure to call unregister_pernet_gen_device() can exhaust memory
if module is loaded/unloaded many times.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/pppol2tp.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/pppol2tp.c b/drivers/net/pppol2tp.c
index e7935d09c89..e0f9219a0ae 100644
--- a/drivers/net/pppol2tp.c
+++ b/drivers/net/pppol2tp.c
@@ -2680,6 +2680,7 @@ out_unregister_pppol2tp_proto:
 static void __exit pppol2tp_exit(void)
 {
 	unregister_pppox_proto(PX_PROTO_OL2TP);
+	unregister_pernet_gen_device(pppol2tp_net_id, &pppol2tp_net_ops);
 	proto_unregister(&pppol2tp_sk_proto);
 }
 
-- 
GitLab


From 144586301f6af5ae5943a002f030d8c626fa4fdd Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Tue, 28 Jul 2009 02:36:15 +0000
Subject: [PATCH 0425/1153] net: net_assign_generic() fix

memcpy() should take into account size of pointers,
not only number of pointers to copy.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/core/net_namespace.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/core/net_namespace.c b/net/core/net_namespace.c
index b7292a2719d..197283072cc 100644
--- a/net/core/net_namespace.c
+++ b/net/core/net_namespace.c
@@ -488,7 +488,7 @@ int net_assign_generic(struct net *net, int id, void *data)
 	 */
 
 	ng->len = id;
-	memcpy(&ng->ptr, &old_ng->ptr, old_ng->len);
+	memcpy(&ng->ptr, &old_ng->ptr, old_ng->len * sizeof(void*));
 
 	rcu_assign_pointer(net->gen, ng);
 	call_rcu(&old_ng->rcu, net_generic_release);
-- 
GitLab


From 1b994b5a1b3cb5395598a08ef3bb0ac118d75c1b Mon Sep 17 00:00:00 2001
From: roel kluin <roel.kluin@gmail.com>
Date: Sat, 1 Aug 2009 20:26:52 +0000
Subject: [PATCH 0426/1153] tulip: Read buffer overflow

Check whether index is within bounds before testing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/tulip/de4x5.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/tulip/de4x5.c b/drivers/net/tulip/de4x5.c
index eb72d2e9ab3..acfdccd4456 100644
--- a/drivers/net/tulip/de4x5.c
+++ b/drivers/net/tulip/de4x5.c
@@ -5059,7 +5059,7 @@ mii_get_phy(struct net_device *dev)
 	if ((id == 0) || (id == 65535)) continue;  /* Valid ID? */
 	for (j=0; j<limit; j++) {                  /* Search PHY table */
 	    if (id != phy_info[j].id) continue;    /* ID match? */
-	    for (k=0; lp->phy[k].id && (k < DE4X5_MAX_PHY); k++);
+	    for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++);
 	    if (k < DE4X5_MAX_PHY) {
 		memcpy((char *)&lp->phy[k],
 		       (char *)&phy_info[j], sizeof(struct phy_table));
@@ -5072,7 +5072,7 @@ mii_get_phy(struct net_device *dev)
 	    break;
 	}
 	if ((j == limit) && (i < DE4X5_MAX_MII)) {
-	    for (k=0; lp->phy[k].id && (k < DE4X5_MAX_PHY); k++);
+	    for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++);
 	    lp->phy[k].addr = i;
 	    lp->phy[k].id = id;
 	    lp->phy[k].spd.reg = GENERIC_REG;      /* ANLPA register         */
@@ -5091,7 +5091,7 @@ mii_get_phy(struct net_device *dev)
   purgatory:
     lp->active = 0;
     if (lp->phy[0].id) {                           /* Reset the PHY devices */
-	for (k=0; lp->phy[k].id && (k < DE4X5_MAX_PHY); k++) { /*For each PHY*/
+	for (k=0; k < DE4X5_MAX_PHY && lp->phy[k].id; k++) { /*For each PHY*/
 	    mii_wr(MII_CR_RST, MII_CR, lp->phy[k].addr, DE4X5_MII);
 	    while (mii_rd(MII_CR, lp->phy[k].addr, DE4X5_MII) & MII_CR_RST);
 
-- 
GitLab


From 54706d99051582993037be5a076aa543fd7f1c38 Mon Sep 17 00:00:00 2001
From: roel kluin <roel.kluin@gmail.com>
Date: Sat, 1 Aug 2009 20:20:13 +0000
Subject: [PATCH 0427/1153] s6gmac: Read buffer overflow

Check whether index is within bounds before testing the element.
In the last iteration i is PHY_MAX_ADDR. the condition
`!(p = pd->mii.bus->phy_map[PHY_MAX_ADDR])' is undefined and may
evaluate to false, which leads to a dereference of this invalid
phy_map in the phy_connect() below.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/s6gmac.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/s6gmac.c b/drivers/net/s6gmac.c
index 5345e47b35a..4525cbe8dd6 100644
--- a/drivers/net/s6gmac.c
+++ b/drivers/net/s6gmac.c
@@ -793,7 +793,7 @@ static inline int s6gmac_phy_start(struct net_device *dev)
 	struct s6gmac *pd = netdev_priv(dev);
 	int i = 0;
 	struct phy_device *p = NULL;
-	while ((!(p = pd->mii.bus->phy_map[i])) && (i < PHY_MAX_ADDR))
+	while ((i < PHY_MAX_ADDR) && (!(p = pd->mii.bus->phy_map[i])))
 		i++;
 	p = phy_connect(dev, dev_name(&p->dev), &s6gmac_adjust_link, 0,
 			PHY_INTERFACE_MODE_RGMII);
-- 
GitLab


From 9bfdac94c78faf68ce038d5c45a385927f2667ce Mon Sep 17 00:00:00 2001
From: roel kluin <roel.kluin@gmail.com>
Date: Fri, 31 Jul 2009 03:43:59 +0000
Subject: [PATCH 0428/1153] mISDN: Read buffer overflow

Check whether index is within bounds before testing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/isdn/mISDN/l1oip_core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/isdn/mISDN/l1oip_core.c b/drivers/isdn/mISDN/l1oip_core.c
index 990e6a7e667..0ebce046ade 100644
--- a/drivers/isdn/mISDN/l1oip_core.c
+++ b/drivers/isdn/mISDN/l1oip_core.c
@@ -1480,7 +1480,7 @@ l1oip_init(void)
 		return -ENOMEM;
 
 	l1oip_cnt = 0;
-	while (type[l1oip_cnt] && l1oip_cnt < MAX_CARDS) {
+	while (l1oip_cnt < MAX_CARDS && type[l1oip_cnt]) {
 		switch (type[l1oip_cnt] & 0xff) {
 		case 1:
 			pri = 0;
-- 
GitLab


From 50c643e7652458e649955408685a16e88ea6dbae Mon Sep 17 00:00:00 2001
From: Dhananjay Phadke <dhananjay@netxen.com>
Date: Sat, 1 Aug 2009 21:36:16 +0000
Subject: [PATCH 0429/1153] netxen: fix coherent dma mask setting

Change default dma mask for NX3031 to 39 bit with ability
to update it to 64-bit (if firmware indicates support). Old
code was restricting it under 4GB (32-bit), sometimes causing
failure to allocate descriptor rings on heavily populated
system. NX2031 based NICs will still get 32-bit coherent mask.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/netxen/netxen_nic_main.c | 37 +++++++++++++++++++---------
 1 file changed, 25 insertions(+), 12 deletions(-)

diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c
index 637ac8b89ba..3cd8cfcf627 100644
--- a/drivers/net/netxen/netxen_nic_main.c
+++ b/drivers/net/netxen/netxen_nic_main.c
@@ -221,7 +221,7 @@ netxen_napi_disable(struct netxen_adapter *adapter)
 	}
 }
 
-static int nx_set_dma_mask(struct netxen_adapter *adapter, uint8_t revision_id)
+static int nx_set_dma_mask(struct netxen_adapter *adapter)
 {
 	struct pci_dev *pdev = adapter->pdev;
 	uint64_t mask, cmask;
@@ -229,19 +229,17 @@ static int nx_set_dma_mask(struct netxen_adapter *adapter, uint8_t revision_id)
 	adapter->pci_using_dac = 0;
 
 	mask = DMA_BIT_MASK(32);
-	/*
-	 * Consistent DMA mask is set to 32 bit because it cannot be set to
-	 * 35 bits. For P3 also leave it at 32 bits for now. Only the rings
-	 * come off this pool.
-	 */
 	cmask = DMA_BIT_MASK(32);
 
+	if (NX_IS_REVISION_P2(adapter->ahw.revision_id)) {
 #ifndef CONFIG_IA64
-	if (revision_id >= NX_P3_B0)
-		mask = DMA_BIT_MASK(39);
-	else if (revision_id == NX_P2_C1)
 		mask = DMA_BIT_MASK(35);
 #endif
+	} else {
+		mask = DMA_BIT_MASK(39);
+		cmask = mask;
+	}
+
 	if (pci_set_dma_mask(pdev, mask) == 0 &&
 		pci_set_consistent_dma_mask(pdev, cmask) == 0) {
 		adapter->pci_using_dac = 1;
@@ -256,7 +254,7 @@ static int
 nx_update_dma_mask(struct netxen_adapter *adapter)
 {
 	int change, shift, err;
-	uint64_t mask, old_mask;
+	uint64_t mask, old_mask, old_cmask;
 	struct pci_dev *pdev = adapter->pdev;
 
 	change = 0;
@@ -272,14 +270,29 @@ nx_update_dma_mask(struct netxen_adapter *adapter)
 
 	if (change) {
 		old_mask = pdev->dma_mask;
+		old_cmask = pdev->dev.coherent_dma_mask;
+
 		mask = (1ULL<<(32+shift)) - 1;
 
 		err = pci_set_dma_mask(pdev, mask);
 		if (err)
-			return pci_set_dma_mask(pdev, old_mask);
+			goto err_out;
+
+		if (NX_IS_REVISION_P3(adapter->ahw.revision_id)) {
+
+			err = pci_set_consistent_dma_mask(pdev, mask);
+			if (err)
+				goto err_out;
+		}
+		dev_info(&pdev->dev, "using %d-bit dma mask\n", 32+shift);
 	}
 
 	return 0;
+
+err_out:
+	pci_set_dma_mask(pdev, old_mask);
+	pci_set_consistent_dma_mask(pdev, old_cmask);
+	return err;
 }
 
 static void netxen_check_options(struct netxen_adapter *adapter)
@@ -1006,7 +1019,7 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	revision_id = pdev->revision;
 	adapter->ahw.revision_id = revision_id;
 
-	err = nx_set_dma_mask(adapter, revision_id);
+	err = nx_set_dma_mask(adapter);
 	if (err)
 		goto err_out_free_netdev;
 
-- 
GitLab


From a6ac65db2329e7685299666f5f7b6093c7b0f3a0 Mon Sep 17 00:00:00 2001
From: Jiri Pirko <jpirko@redhat.com>
Date: Thu, 30 Jul 2009 01:06:12 +0000
Subject: [PATCH 0430/1153] net: restore the original spinlock to protect
 unicast list

There is a path when an assetion in dev_unicast_sync() appears.

igmp6_group_added -> dev_mc_add -> __dev_set_rx_mode ->
-> vlan_dev_set_rx_mode -> dev_unicast_sync

Therefore we cannot protect this list with rtnl. This patch restores the
original protecting this list with spinlock.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/core/dev.c | 25 ++++++++++++++++---------
 1 file changed, 16 insertions(+), 9 deletions(-)

diff --git a/net/core/dev.c b/net/core/dev.c
index 70c27e0c7c3..43e61ba7bd9 100644
--- a/net/core/dev.c
+++ b/net/core/dev.c
@@ -3865,10 +3865,12 @@ int dev_unicast_delete(struct net_device *dev, void *addr)
 
 	ASSERT_RTNL();
 
+	netif_addr_lock_bh(dev);
 	err = __hw_addr_del(&dev->uc, addr, dev->addr_len,
 			    NETDEV_HW_ADDR_T_UNICAST);
 	if (!err)
 		__dev_set_rx_mode(dev);
+	netif_addr_unlock_bh(dev);
 	return err;
 }
 EXPORT_SYMBOL(dev_unicast_delete);
@@ -3889,10 +3891,12 @@ int dev_unicast_add(struct net_device *dev, void *addr)
 
 	ASSERT_RTNL();
 
+	netif_addr_lock_bh(dev);
 	err = __hw_addr_add(&dev->uc, addr, dev->addr_len,
 			    NETDEV_HW_ADDR_T_UNICAST);
 	if (!err)
 		__dev_set_rx_mode(dev);
+	netif_addr_unlock_bh(dev);
 	return err;
 }
 EXPORT_SYMBOL(dev_unicast_add);
@@ -3949,7 +3953,8 @@ void __dev_addr_unsync(struct dev_addr_list **to, int *to_count,
  *	@from: source device
  *
  *	Add newly added addresses to the destination device and release
- *	addresses that have no users left.
+ *	addresses that have no users left. The source device must be
+ *	locked by netif_tx_lock_bh.
  *
  *	This function is intended to be called from the dev->set_rx_mode
  *	function of layered software devices.
@@ -3958,14 +3963,14 @@ int dev_unicast_sync(struct net_device *to, struct net_device *from)
 {
 	int err = 0;
 
-	ASSERT_RTNL();
-
 	if (to->addr_len != from->addr_len)
 		return -EINVAL;
 
+	netif_addr_lock_bh(to);
 	err = __hw_addr_sync(&to->uc, &from->uc, to->addr_len);
 	if (!err)
 		__dev_set_rx_mode(to);
+	netif_addr_unlock_bh(to);
 	return err;
 }
 EXPORT_SYMBOL(dev_unicast_sync);
@@ -3981,28 +3986,30 @@ EXPORT_SYMBOL(dev_unicast_sync);
  */
 void dev_unicast_unsync(struct net_device *to, struct net_device *from)
 {
-	ASSERT_RTNL();
-
 	if (to->addr_len != from->addr_len)
 		return;
 
+	netif_addr_lock_bh(from);
+	netif_addr_lock(to);
 	__hw_addr_unsync(&to->uc, &from->uc, to->addr_len);
 	__dev_set_rx_mode(to);
+	netif_addr_unlock(to);
+	netif_addr_unlock_bh(from);
 }
 EXPORT_SYMBOL(dev_unicast_unsync);
 
 static void dev_unicast_flush(struct net_device *dev)
 {
-	/* rtnl_mutex must be held here */
-
+	netif_addr_lock_bh(dev);
 	__hw_addr_flush(&dev->uc);
+	netif_addr_unlock_bh(dev);
 }
 
 static void dev_unicast_init(struct net_device *dev)
 {
-	/* rtnl_mutex must be held here */
-
+	netif_addr_lock_bh(dev);
 	__hw_addr_init(&dev->uc);
+	netif_addr_unlock_bh(dev);
 }
 
 
-- 
GitLab


From df4e7f72f5156ef16a918da8a575ba90ec27ab77 Mon Sep 17 00:00:00 2001
From: Don Fry <pcnet32@verizon.net>
Date: Fri, 31 Jul 2009 08:40:06 +0000
Subject: [PATCH 0431/1153] pcnet32: remove superfluous NULL pointer check in
 pcnet32_probe1()

Move the debug printk() into the proper place and remove superfluous
NULL pointer check in pcnet32_probe1().

This takes care of the following entry from Dan's list:

drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev'

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by:  Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/pcnet32.c | 18 +++++++-----------
 1 file changed, 7 insertions(+), 11 deletions(-)

diff --git a/drivers/net/pcnet32.c b/drivers/net/pcnet32.c
index 1c35e1d637a..b61c97254b3 100644
--- a/drivers/net/pcnet32.c
+++ b/drivers/net/pcnet32.c
@@ -1611,8 +1611,11 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
 		if (pcnet32_dwio_read_csr(ioaddr, 0) == 4
 		    && pcnet32_dwio_check(ioaddr)) {
 			a = &pcnet32_dwio;
-		} else
+		} else {
+			if (pcnet32_debug & NETIF_MSG_PROBE)
+				printk(KERN_ERR PFX "No access methods\n");
 			goto err_release_region;
+		}
 	}
 
 	chip_version =
@@ -1852,12 +1855,6 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
 	    ((cards_found >= MAX_UNITS) || full_duplex[cards_found]))
 		lp->options |= PCNET32_PORT_FD;
 
-	if (!a) {
-		if (pcnet32_debug & NETIF_MSG_PROBE)
-			printk(KERN_ERR PFX "No access methods\n");
-		ret = -ENODEV;
-		goto err_free_consistent;
-	}
 	lp->a = *a;
 
 	/* prior to register_netdev, dev->name is not yet correct */
@@ -1973,14 +1970,13 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
 
 	return 0;
 
-      err_free_ring:
+err_free_ring:
 	pcnet32_free_ring(dev);
-      err_free_consistent:
 	pci_free_consistent(lp->pci_dev, sizeof(*lp->init_block),
 			    lp->init_block, lp->init_dma_addr);
-      err_free_netdev:
+err_free_netdev:
 	free_netdev(dev);
-      err_release_region:
+err_release_region:
 	release_region(ioaddr, PCNET32_TOTAL_SIZE);
 	return ret;
 }
-- 
GitLab


From 63097b3ad85788a64c75091bff351ecc850761b2 Mon Sep 17 00:00:00 2001
From: Don Fry <pcnet32@verizon.net>
Date: Fri, 31 Jul 2009 08:45:29 +0000
Subject: [PATCH 0432/1153] pcnet32: VLB support fixes

VLB support has been broken since at least 2004-2005 period as some
changes introduced back then assumed that ->pci_dev is always valid,
lets try to fix it:

- remove duplicated SET_NETDEV_DEV() call

- call SET_NETDEV_DEV() only for PCI devices

- check for ->pci_dev validity in pcnet32_open()

[ Alternatively we may consider removing VLB support but there would not
  be much gain in it since an extra driver code needed for VLB support is
  minimal and quite simple. ]

This takes care of the following entry from Dan's list:

drivers/net/pcnet32.c +1889 pcnet32_probe1(298) warning: variable derefenced before check 'pdev'

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by:  Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/pcnet32.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/net/pcnet32.c b/drivers/net/pcnet32.c
index b61c97254b3..16964ec73e6 100644
--- a/drivers/net/pcnet32.c
+++ b/drivers/net/pcnet32.c
@@ -1722,7 +1722,9 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
 		ret = -ENOMEM;
 		goto err_release_region;
 	}
-	SET_NETDEV_DEV(dev, &pdev->dev);
+
+	if (pdev)
+		SET_NETDEV_DEV(dev, &pdev->dev);
 
 	if (pcnet32_debug & NETIF_MSG_PROBE)
 		printk(KERN_INFO PFX "%s at %#3lx,", chipname, ioaddr);
@@ -1821,7 +1823,6 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
 
 	spin_lock_init(&lp->lock);
 
-	SET_NETDEV_DEV(dev, &pdev->dev);
 	lp->name = chipname;
 	lp->shared_irq = shared;
 	lp->tx_ring_size = TX_RING_SIZE;	/* default tx ring size */
@@ -2085,6 +2086,7 @@ static void pcnet32_free_ring(struct net_device *dev)
 static int pcnet32_open(struct net_device *dev)
 {
 	struct pcnet32_private *lp = netdev_priv(dev);
+	struct pci_dev *pdev = lp->pci_dev;
 	unsigned long ioaddr = dev->base_addr;
 	u16 val;
 	int i;
@@ -2145,9 +2147,9 @@ static int pcnet32_open(struct net_device *dev)
 	lp->a.write_csr(ioaddr, 124, val);
 
 	/* Allied Telesyn AT 2700/2701 FX are 100Mbit only and do not negotiate */
-	if (lp->pci_dev->subsystem_vendor == PCI_VENDOR_ID_AT &&
-	    (lp->pci_dev->subsystem_device == PCI_SUBDEVICE_ID_AT_2700FX ||
-	     lp->pci_dev->subsystem_device == PCI_SUBDEVICE_ID_AT_2701FX)) {
+	if (pdev && pdev->subsystem_vendor == PCI_VENDOR_ID_AT &&
+	    (pdev->subsystem_device == PCI_SUBDEVICE_ID_AT_2700FX ||
+	     pdev->subsystem_device == PCI_SUBDEVICE_ID_AT_2701FX)) {
 		if (lp->options & PCNET32_PORT_ASEL) {
 			lp->options = PCNET32_PORT_FD | PCNET32_PORT_100;
 			if (netif_msg_link(lp))
-- 
GitLab


From 5973bee46fe66db94fab198979dec87f263fc2a8 Mon Sep 17 00:00:00 2001
From: Linus Walleij <linus.walleij@stericsson.com>
Date: Tue, 21 Jul 2009 00:40:46 +0200
Subject: [PATCH 0433/1153] [WATCHDOG] Fix COH 901 327 watchdog enablement

Since the COH 901 327 found in U300 is clocked at 32 kHz we need
to wait for the interrupt clearing flag to propagate through
hardware in order not to accidentally fire off any interrupts
when we enable them.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
---
 drivers/watchdog/coh901327_wdt.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/watchdog/coh901327_wdt.c b/drivers/watchdog/coh901327_wdt.c
index fecb307d28e..aec7cefdef2 100644
--- a/drivers/watchdog/coh901327_wdt.c
+++ b/drivers/watchdog/coh901327_wdt.c
@@ -18,6 +18,7 @@
 #include <linux/bitops.h>
 #include <linux/uaccess.h>
 #include <linux/clk.h>
+#include <linux/delay.h>
 
 #define DRV_NAME "WDOG COH 901 327"
 
@@ -92,6 +93,8 @@ static struct clk *clk;
 static void coh901327_enable(u16 timeout)
 {
 	u16 val;
+	unsigned long freq;
+	unsigned long delay_ns;
 
 	clk_enable(clk);
 	/* Restart timer if it is disabled */
@@ -102,6 +105,14 @@ static void coh901327_enable(u16 timeout)
 	/* Acknowledge any pending interrupt so it doesn't just fire off */
 	writew(U300_WDOG_IER_WILL_BARK_IRQ_ACK_ENABLE,
 	       virtbase + U300_WDOG_IER);
+	/*
+	 * The interrupt is cleared in the 32 kHz clock domain.
+	 * Wait 3 32 kHz cycles for it to take effect
+	 */
+	freq = clk_get_rate(clk);
+	delay_ns = (1000000000 + freq - 1) / freq; /* Freq to ns and round up */
+	delay_ns = 3 * delay_ns; /* Wait 3 cycles */
+	ndelay(delay_ns);
 	/* Enable the watchdog interrupt */
 	writew(U300_WDOG_IMR_WILL_BARK_IRQ_ENABLE, virtbase + U300_WDOG_IMR);
 	/* Activate the watchdog timer */
-- 
GitLab


From b564afcfb82fe3e63a7ce05a944eb5e11244d7cb Mon Sep 17 00:00:00 2001
From: Andreas Eversberg <andreas@eversberg.eu>
Date: Mon, 27 Jul 2009 07:24:04 +0000
Subject: [PATCH 0434/1153] mISDN: Fix handling of receive buffer size in L1oIP

The size of receive buffer pointer was used to get size of
receive buffer instead of recvbuf_size itself, so only 4/8
bytes could be transfered.

This is a regression to 2.6.30 introduced by commit 8c90e11e3543d7de612194a042a148caeaab5f1d
mISDN: Use kernel_{send,recv}msg instead of open coding

Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/isdn/mISDN/l1oip_core.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/isdn/mISDN/l1oip_core.c b/drivers/isdn/mISDN/l1oip_core.c
index 0ebce046ade..7e5f30dbc0a 100644
--- a/drivers/isdn/mISDN/l1oip_core.c
+++ b/drivers/isdn/mISDN/l1oip_core.c
@@ -731,10 +731,10 @@ l1oip_socket_thread(void *data)
 	while (!signal_pending(current)) {
 		struct kvec iov = {
 			.iov_base = recvbuf,
-			.iov_len = sizeof(recvbuf),
+			.iov_len = recvbuf_size,
 		};
 		recvlen = kernel_recvmsg(socket, &msg, &iov, 1,
-					 sizeof(recvbuf), 0);
+					 recvbuf_size, 0);
 		if (recvlen > 0) {
 			l1oip_socket_parse(hc, &sin_rx, recvbuf, recvlen);
 		} else {
-- 
GitLab


From 79896cf42f6a96d7e14f2dc3473443d68d74031d Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun, 2 Aug 2009 14:04:19 -0700
Subject: [PATCH 0435/1153] Make pci_claim_resource() use request_resource()
 rather than insert_resource()

This function has traditionally used "insert_resource()", because before
commit cebd78a8c5 ("Fix pci_claim_resource") it used to just insert the
resource into whatever root resource tree that was indicated by
"pcibios_select_root()".

So there Matthew fixed it to actually look up the proper parent
resource, which means that now it's actively wrong to then traverse the
resource tree any more: we already know exactly where the new resource
should go.

And when we then did commit a76117dfd6 ("x86: Use pci_claim_resource"),
which changed the x86 PCI code from the open-coded

	pr = pci_find_parent_resource(dev, r);
	if (!pr || request_resource(pr, r) < 0) {

to using

	if (pci_claim_resource(dev, idx) < 0) {

that "insert_resource()" now suddenly became a problem, and causes a
regression covered by

	http://bugzilla.kernel.org/show_bug.cgi?id=13891

which this fixes.

Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Linux PCI <linux-pci@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/pci/setup-res.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/setup-res.c b/drivers/pci/setup-res.c
index b711fb7181e..1898c7b4790 100644
--- a/drivers/pci/setup-res.c
+++ b/drivers/pci/setup-res.c
@@ -100,16 +100,16 @@ int pci_claim_resource(struct pci_dev *dev, int resource)
 {
 	struct resource *res = &dev->resource[resource];
 	struct resource *root;
-	char *dtype = resource < PCI_BRIDGE_RESOURCES ? "device" : "bridge";
 	int err;
 
 	root = pci_find_parent_resource(dev, res);
 
 	err = -EINVAL;
 	if (root != NULL)
-		err = insert_resource(root, res);
+		err = request_resource(root, res);
 
 	if (err) {
+		const char *dtype = resource < PCI_BRIDGE_RESOURCES ? "device" : "bridge";
 		dev_err(&dev->dev, "BAR %d: %s of %s %pR\n",
 			resource,
 			root ? "address space collision on" :
-- 
GitLab


From 57d7f282271a83fe4ca4bd15eee79be577210210 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Fri, 31 Jul 2009 21:28:16 -0700
Subject: [PATCH 0436/1153] TTY: Maintainer change

Clearly, I am a glutton for punishment.  I'll see if I can see Alan's
changes through to the end, otherwise I'll be fending off a lot of bug
reports for usb-serial devices.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index d6befb2c470..b1114cfac6b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4995,7 +4995,9 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial.git
 S:	Maintained
 
 TTY LAYER
-S:	Orphan
+M:	Greg Kroah-Hartman <gregkh@suse.de>
+S:	Maintained
+T:	quilt kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/
 F:	drivers/char/tty_*
 F:	drivers/serial/serial_core.c
 F:	include/linux/serial_core.h
-- 
GitLab


From ac5e7113e74872928844d00085bd47c988f12728 Mon Sep 17 00:00:00 2001
From: Andre Noll <maan@systemlinux.org>
Date: Mon, 3 Aug 2009 10:59:47 +1000
Subject: [PATCH 0437/1153] md: Push down data integrity code to personalities.

This patch replaces md_integrity_check() by two new public functions:
md_integrity_register() and md_integrity_add_rdev() which are both
personality-independent.

md_integrity_register() is called from the ->run and ->hot_remove
methods of all personalities that support data integrity.  The
function iterates over the component devices of the array and
determines if all active devices are integrity capable and if their
profiles match. If this is the case, the common profile is registered
for the mddev via blk_integrity_register().

The second new function, md_integrity_add_rdev() is called from the
->hot_add_disk methods, i.e. whenever a new device is being added
to a raid array. If the new device does not support data integrity,
or has a profile different from the one already registered, data
integrity for the mddev is disabled.

For raid0 and linear, only the call to md_integrity_register() from
the ->run method is necessary.

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/linear.c    |  1 +
 drivers/md/md.c        | 94 ++++++++++++++++++++++++++++--------------
 drivers/md/md.h        |  2 +
 drivers/md/multipath.c |  5 ++-
 drivers/md/raid0.c     |  1 +
 drivers/md/raid1.c     |  6 ++-
 drivers/md/raid10.c    |  4 ++
 7 files changed, 80 insertions(+), 33 deletions(-)

diff --git a/drivers/md/linear.c b/drivers/md/linear.c
index 5810fa906af..54c8677f1e5 100644
--- a/drivers/md/linear.c
+++ b/drivers/md/linear.c
@@ -220,6 +220,7 @@ static int linear_run (mddev_t *mddev)
 	mddev->queue->unplug_fn = linear_unplug;
 	mddev->queue->backing_dev_info.congested_fn = linear_congested;
 	mddev->queue->backing_dev_info.congested_data = mddev;
+	md_integrity_register(mddev);
 	return 0;
 }
 
diff --git a/drivers/md/md.c b/drivers/md/md.c
index d4351ff0849..180949e94a7 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -1487,37 +1487,76 @@ static int match_mddev_units(mddev_t *mddev1, mddev_t *mddev2)
 
 static LIST_HEAD(pending_raid_disks);
 
-static void md_integrity_check(mdk_rdev_t *rdev, mddev_t *mddev)
+/*
+ * Try to register data integrity profile for an mddev
+ *
+ * This is called when an array is started and after a disk has been kicked
+ * from the array. It only succeeds if all working and active component devices
+ * are integrity capable with matching profiles.
+ */
+int md_integrity_register(mddev_t *mddev)
+{
+	mdk_rdev_t *rdev, *reference = NULL;
+
+	if (list_empty(&mddev->disks))
+		return 0; /* nothing to do */
+	if (blk_get_integrity(mddev->gendisk))
+		return 0; /* already registered */
+	list_for_each_entry(rdev, &mddev->disks, same_set) {
+		/* skip spares and non-functional disks */
+		if (test_bit(Faulty, &rdev->flags))
+			continue;
+		if (rdev->raid_disk < 0)
+			continue;
+		/*
+		 * If at least one rdev is not integrity capable, we can not
+		 * enable data integrity for the md device.
+		 */
+		if (!bdev_get_integrity(rdev->bdev))
+			return -EINVAL;
+		if (!reference) {
+			/* Use the first rdev as the reference */
+			reference = rdev;
+			continue;
+		}
+		/* does this rdev's profile match the reference profile? */
+		if (blk_integrity_compare(reference->bdev->bd_disk,
+				rdev->bdev->bd_disk) < 0)
+			return -EINVAL;
+	}
+	/*
+	 * All component devices are integrity capable and have matching
+	 * profiles, register the common profile for the md device.
+	 */
+	if (blk_integrity_register(mddev->gendisk,
+			bdev_get_integrity(reference->bdev)) != 0) {
+		printk(KERN_ERR "md: failed to register integrity for %s\n",
+			mdname(mddev));
+		return -EINVAL;
+	}
+	printk(KERN_NOTICE "md: data integrity on %s enabled\n",
+		mdname(mddev));
+	return 0;
+}
+EXPORT_SYMBOL(md_integrity_register);
+
+/* Disable data integrity if non-capable/non-matching disk is being added */
+void md_integrity_add_rdev(mdk_rdev_t *rdev, mddev_t *mddev)
 {
-	struct mdk_personality *pers = mddev->pers;
-	struct gendisk *disk = mddev->gendisk;
 	struct blk_integrity *bi_rdev = bdev_get_integrity(rdev->bdev);
-	struct blk_integrity *bi_mddev = blk_get_integrity(disk);
+	struct blk_integrity *bi_mddev = blk_get_integrity(mddev->gendisk);
 
-	/* Data integrity passthrough not supported on RAID 4, 5 and 6 */
-	if (pers && pers->level >= 4 && pers->level <= 6)
+	if (!bi_mddev) /* nothing to do */
 		return;
-
-	/* If rdev is integrity capable, register profile for mddev */
-	if (!bi_mddev && bi_rdev) {
-		if (blk_integrity_register(disk, bi_rdev))
-			printk(KERN_ERR "%s: %s Could not register integrity!\n",
-			       __func__, disk->disk_name);
-		else
-			printk(KERN_NOTICE "Enabling data integrity on %s\n",
-			       disk->disk_name);
+	if (rdev->raid_disk < 0) /* skip spares */
 		return;
-	}
-
-	/* Check that mddev and rdev have matching profiles */
-	if (blk_integrity_compare(disk, rdev->bdev->bd_disk) < 0) {
-		printk(KERN_ERR "%s: %s/%s integrity mismatch!\n", __func__,
-		       disk->disk_name, rdev->bdev->bd_disk->disk_name);
-		printk(KERN_NOTICE "Disabling data integrity on %s\n",
-		       disk->disk_name);
-		blk_integrity_unregister(disk);
-	}
+	if (bi_rdev && blk_integrity_compare(mddev->gendisk,
+					     rdev->bdev->bd_disk) >= 0)
+		return;
+	printk(KERN_NOTICE "disabling data integrity on %s\n", mdname(mddev));
+	blk_integrity_unregister(mddev->gendisk);
 }
+EXPORT_SYMBOL(md_integrity_add_rdev);
 
 static int bind_rdev_to_array(mdk_rdev_t * rdev, mddev_t * mddev)
 {
@@ -1591,7 +1630,6 @@ static int bind_rdev_to_array(mdk_rdev_t * rdev, mddev_t * mddev)
 	/* May as well allow recovery to be retried once */
 	mddev->recovery_disabled = 0;
 
-	md_integrity_check(rdev, mddev);
 	return 0;
 
  fail:
@@ -4048,10 +4086,6 @@ static int do_md_run(mddev_t * mddev)
 	}
 	strlcpy(mddev->clevel, pers->name, sizeof(mddev->clevel));
 
-	if (pers->level >= 4 && pers->level <= 6)
-		/* Cannot support integrity (yet) */
-		blk_integrity_unregister(mddev->gendisk);
-
 	if (mddev->reshape_position != MaxSector &&
 	    pers->start_reshape == NULL) {
 		/* This personality cannot handle reshaping... */
diff --git a/drivers/md/md.h b/drivers/md/md.h
index 9430a110db9..78f03168baf 100644
--- a/drivers/md/md.h
+++ b/drivers/md/md.h
@@ -431,5 +431,7 @@ extern int md_allow_write(mddev_t *mddev);
 extern void md_wait_for_blocked_rdev(mdk_rdev_t *rdev, mddev_t *mddev);
 extern void md_set_array_sectors(mddev_t *mddev, sector_t array_sectors);
 extern int md_check_no_bitmap(mddev_t *mddev);
+extern int md_integrity_register(mddev_t *mddev);
+void md_integrity_add_rdev(mdk_rdev_t *rdev, mddev_t *mddev);
 
 #endif /* _MD_MD_H */
diff --git a/drivers/md/multipath.c b/drivers/md/multipath.c
index 237fe3fd235..7140909f666 100644
--- a/drivers/md/multipath.c
+++ b/drivers/md/multipath.c
@@ -313,6 +313,7 @@ static int multipath_add_disk(mddev_t *mddev, mdk_rdev_t *rdev)
 			set_bit(In_sync, &rdev->flags);
 			rcu_assign_pointer(p->rdev, rdev);
 			err = 0;
+			md_integrity_add_rdev(rdev, mddev);
 			break;
 		}
 
@@ -345,7 +346,9 @@ static int multipath_remove_disk(mddev_t *mddev, int number)
 			/* lost the race, try later */
 			err = -EBUSY;
 			p->rdev = rdev;
+			goto abort;
 		}
+		md_integrity_register(mddev);
 	}
 abort:
 
@@ -519,7 +522,7 @@ static int multipath_run (mddev_t *mddev)
 	mddev->queue->unplug_fn = multipath_unplug;
 	mddev->queue->backing_dev_info.congested_fn = multipath_congested;
 	mddev->queue->backing_dev_info.congested_data = mddev;
-
+	md_integrity_register(mddev);
 	return 0;
 
 out_free_conf:
diff --git a/drivers/md/raid0.c b/drivers/md/raid0.c
index 335f490dcad..898e2bdfee4 100644
--- a/drivers/md/raid0.c
+++ b/drivers/md/raid0.c
@@ -351,6 +351,7 @@ static int raid0_run(mddev_t *mddev)
 
 	blk_queue_merge_bvec(mddev->queue, raid0_mergeable_bvec);
 	dump_zones(mddev);
+	md_integrity_register(mddev);
 	return 0;
 }
 
diff --git a/drivers/md/raid1.c b/drivers/md/raid1.c
index 0569efba0c0..67e794d0097 100644
--- a/drivers/md/raid1.c
+++ b/drivers/md/raid1.c
@@ -1144,7 +1144,7 @@ static int raid1_add_disk(mddev_t *mddev, mdk_rdev_t *rdev)
 			rcu_assign_pointer(p->rdev, rdev);
 			break;
 		}
-
+	md_integrity_add_rdev(rdev, mddev);
 	print_conf(conf);
 	return err;
 }
@@ -1178,7 +1178,9 @@ static int raid1_remove_disk(mddev_t *mddev, int number)
 			/* lost the race, try later */
 			err = -EBUSY;
 			p->rdev = rdev;
+			goto abort;
 		}
+		md_integrity_register(mddev);
 	}
 abort:
 
@@ -2067,7 +2069,7 @@ static int run(mddev_t *mddev)
 	mddev->queue->unplug_fn = raid1_unplug;
 	mddev->queue->backing_dev_info.congested_fn = raid1_congested;
 	mddev->queue->backing_dev_info.congested_data = mddev;
-
+	md_integrity_register(mddev);
 	return 0;
 
 out_no_mem:
diff --git a/drivers/md/raid10.c b/drivers/md/raid10.c
index 7298a5e5a18..3d9020cf6f6 100644
--- a/drivers/md/raid10.c
+++ b/drivers/md/raid10.c
@@ -1170,6 +1170,7 @@ static int raid10_add_disk(mddev_t *mddev, mdk_rdev_t *rdev)
 			break;
 		}
 
+	md_integrity_add_rdev(rdev, mddev);
 	print_conf(conf);
 	return err;
 }
@@ -1203,7 +1204,9 @@ static int raid10_remove_disk(mddev_t *mddev, int number)
 			/* lost the race, try later */
 			err = -EBUSY;
 			p->rdev = rdev;
+			goto abort;
 		}
+		md_integrity_register(mddev);
 	}
 abort:
 
@@ -2225,6 +2228,7 @@ static int run(mddev_t *mddev)
 
 	if (conf->near_copies < mddev->raid_disks)
 		blk_queue_merge_bvec(mddev->queue, raid10_mergeable_bvec);
+	md_integrity_register(mddev);
 	return 0;
 
 out_free_conf:
-- 
GitLab


From 3a981b03f38dc3b8a69b77cbc679e66c1318a44a Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Mon, 3 Aug 2009 10:59:55 +1000
Subject: [PATCH 0438/1153] md: when a level change reduces the number of
 devices, remove the excess.

When an array is changed from RAID6 to RAID5, fewer drives are
needed.  So any device that is made superfluous by the level
conversion must be marked as not-active.
For the RAID6->RAID5 conversion, this will be a drive which only
has 'Q' blocks on it.

Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/md.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/md/md.c b/drivers/md/md.c
index 180949e94a7..c194955aeca 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -2695,6 +2695,7 @@ level_store(mddev_t *mddev, const char *buf, size_t len)
 	ssize_t rv = len;
 	struct mdk_personality *pers;
 	void *priv;
+	mdk_rdev_t *rdev;
 
 	if (mddev->pers == NULL) {
 		if (len == 0)
@@ -2774,6 +2775,12 @@ level_store(mddev_t *mddev, const char *buf, size_t len)
 	mddev_suspend(mddev);
 	mddev->pers->stop(mddev);
 	module_put(mddev->pers->owner);
+	/* Invalidate devices that are now superfluous */
+	list_for_each_entry(rdev, &mddev->disks, same_set)
+		if (rdev->raid_disk >= mddev->raid_disks) {
+			rdev->raid_disk = -1;
+			clear_bit(In_sync, &rdev->flags);
+		}
 	mddev->pers = pers;
 	mddev->private = priv;
 	strlcpy(mddev->clevel, pers->name, sizeof(mddev->clevel));
-- 
GitLab


From 3673f305faf1bc66ead751344f8262ace851ff44 Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Mon, 3 Aug 2009 10:59:56 +1000
Subject: [PATCH 0439/1153] md: avoid array overflow with bad v1.x metadata

We trust the 'desc_nr' field in v1.x metadata enough to use it
as an index in an array.  This isn't really safe.
So range-check the value first.

Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/md.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/md/md.c b/drivers/md/md.c
index c194955aeca..249b2896d4e 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -1308,7 +1308,12 @@ static int super_1_validate(mddev_t *mddev, mdk_rdev_t *rdev)
 	}
 	if (mddev->level != LEVEL_MULTIPATH) {
 		int role;
-		role = le16_to_cpu(sb->dev_roles[rdev->desc_nr]);
+		if (rdev->desc_nr < 0 ||
+		    rdev->desc_nr >= le32_to_cpu(sb->max_dev)) {
+			role = 0xffff;
+			rdev->desc_nr = -1;
+		} else
+			role = le16_to_cpu(sb->dev_roles[rdev->desc_nr]);
 		switch(role) {
 		case 0xffff: /* spare */
 			break;
-- 
GitLab


From 70471dafe3390243c598a3165dfb86b8b8b3f4fe Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Mon, 3 Aug 2009 10:59:57 +1000
Subject: [PATCH 0440/1153] md: Handle growth of v1.x metadata correctly.

The v1.x metadata does not have a fixed size and can grow
when devices are added.
If it grows enough to require an extra sector of storage,
we need to update the 'sb_size' to match.

Without this, md can write out an incomplete superblock with a
bad checksum, which will be rejected when trying to re-assemble
the array.

Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/md.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/md/md.c b/drivers/md/md.c
index 249b2896d4e..52c988b072d 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -1399,8 +1399,14 @@ static void super_1_sync(mddev_t *mddev, mdk_rdev_t *rdev)
 		if (rdev2->desc_nr+1 > max_dev)
 			max_dev = rdev2->desc_nr+1;
 
-	if (max_dev > le32_to_cpu(sb->max_dev))
+	if (max_dev > le32_to_cpu(sb->max_dev)) {
+		int bmask;
 		sb->max_dev = cpu_to_le32(max_dev);
+		rdev->sb_size = max_dev * 2 + 256;
+		bmask = queue_logical_block_size(rdev->bdev->bd_disk->queue)-1;
+		if (rdev->sb_size & bmask)
+			rdev->sb_size = (rdev->sb_size | bmask) + 1;
+	}
 	for (i=0; i<max_dev;i++)
 		sb->dev_roles[i] = cpu_to_le16(0xfffe);
 	
-- 
GitLab


From e516402c0d4fc02be4af9fa8c18954d4f9deb44e Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Mon, 3 Aug 2009 10:59:57 +1000
Subject: [PATCH 0441/1153] md/raid5: set reshape_position correctly when
 reshape starts.

As the internal reshape_progress counter is the main driver
for reshape, the fact that reshape_position sometimes starts with the
wrong value has minimal effect.  It is visible in sysfs and that
is all.

Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/raid5.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index 39374230a46..659151e5eda 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -5000,7 +5000,7 @@ static int raid5_start_reshape(mddev_t *mddev)
 		spin_unlock_irqrestore(&conf->device_lock, flags);
 	}
 	mddev->raid_disks = conf->raid_disks;
-	mddev->reshape_position = 0;
+	mddev->reshape_position = conf->reshape_progress;
 	set_bit(MD_CHANGE_DEVS, &mddev->flags);
 
 	clear_bit(MD_RECOVERY_SYNC, &mddev->recovery);
-- 
GitLab


From 64bd660b51b2da92e99a5e97349f6558349f11c5 Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Mon, 3 Aug 2009 10:59:58 +1000
Subject: [PATCH 0442/1153] md: allow raid5_quiesce to work properly when
 reshape is happening.

The ->quiesce method is not supposed to stop resync/recovery/reshape,
just normal IO.
But in raid5 we don't have a way to know which stripes are being
used for normal IO and which for resync etc, so we need to wait for
all stripes to be idle to be sure that all writes have completed.

However reshape keeps at least some stripe busy for an extended period
of time, so a call to raid5_quiesce can block for several seconds
needlessly.
So arrange for reshape etc to pause briefly while raid5_quiesce is
trying to quiesce the array so that the active_stripes count can
drop to zero.

Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/raid5.c | 11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)

diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index 659151e5eda..2dc35b4c20a 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -3999,6 +3999,9 @@ static inline sector_t sync_request(mddev_t *mddev, sector_t sector_nr, int *ski
 		return 0;
 	}
 
+	/* Allow raid5_quiesce to complete */
+	wait_event(conf->wait_for_overlap, conf->quiesce != 2);
+
 	if (test_bit(MD_RECOVERY_RESHAPE, &mddev->recovery))
 		return reshape_request(mddev, sector_nr, skipped);
 
@@ -5104,12 +5107,18 @@ static void raid5_quiesce(mddev_t *mddev, int state)
 
 	case 1: /* stop all writes */
 		spin_lock_irq(&conf->device_lock);
-		conf->quiesce = 1;
+		/* '2' tells resync/reshape to pause so that all
+		 * active stripes can drain
+		 */
+		conf->quiesce = 2;
 		wait_event_lock_irq(conf->wait_for_stripe,
 				    atomic_read(&conf->active_stripes) == 0 &&
 				    atomic_read(&conf->active_aligned_reads) == 0,
 				    conf->device_lock, /* nothing */);
+		conf->quiesce = 1;
 		spin_unlock_irq(&conf->device_lock);
+		/* allow reshape to continue */
+		wake_up(&conf->wait_for_overlap);
 		break;
 
 	case 0: /* re-enable writes */
-- 
GitLab


From 449aad3e25358812c43afc60918c5ad3819488e7 Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Mon, 3 Aug 2009 10:59:58 +1000
Subject: [PATCH 0443/1153] md: Use revalidate_disk to effect changes in size
 of device.

As revalidate_disk calls check_disk_size_change, it will cause
any capacity change of a gendisk to be propagated to the blockdev
inode.  So use that instead of mucking about with locks and
i_size_write.

Also add a call to revalidate_disk in do_md_run and a few other places
where the gendisk capacity is changed.

Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/linear.c |  1 +
 drivers/md/md.c     | 28 +++++-----------------------
 drivers/md/raid1.c  |  1 +
 drivers/md/raid5.c  | 12 ++----------
 4 files changed, 9 insertions(+), 33 deletions(-)

diff --git a/drivers/md/linear.c b/drivers/md/linear.c
index 54c8677f1e5..5fe39c2a3d2 100644
--- a/drivers/md/linear.c
+++ b/drivers/md/linear.c
@@ -257,6 +257,7 @@ static int linear_add(mddev_t *mddev, mdk_rdev_t *rdev)
 	rcu_assign_pointer(mddev->private, newconf);
 	md_set_array_sectors(mddev, linear_size(mddev, 0, 0));
 	set_capacity(mddev->gendisk, mddev->array_sectors);
+	revalidate_disk(mddev->gendisk);
 	call_rcu(&oldconf->rcu, free_conf);
 	return 0;
 }
diff --git a/drivers/md/md.c b/drivers/md/md.c
index 52c988b072d..5b98bea4ff9 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -3741,17 +3741,8 @@ array_size_store(mddev_t *mddev, const char *buf, size_t len)
 
 	mddev->array_sectors = sectors;
 	set_capacity(mddev->gendisk, mddev->array_sectors);
-	if (mddev->pers) {
-		struct block_device *bdev = bdget_disk(mddev->gendisk, 0);
-
-		if (bdev) {
-			mutex_lock(&bdev->bd_inode->i_mutex);
-			i_size_write(bdev->bd_inode,
-				     (loff_t)mddev->array_sectors << 9);
-			mutex_unlock(&bdev->bd_inode->i_mutex);
-			bdput(bdev);
-		}
-	}
+	if (mddev->pers)
+		revalidate_disk(mddev->gendisk);
 
 	return len;
 }
@@ -4241,6 +4232,7 @@ static int do_md_run(mddev_t * mddev)
 	md_wakeup_thread(mddev->thread);
 	md_wakeup_thread(mddev->sync_thread); /* possibly kick off a reshape */
 
+	revalidate_disk(mddev->gendisk);
 	mddev->changed = 1;
 	md_new_event(mddev);
 	sysfs_notify_dirent(mddev->sysfs_state);
@@ -5139,18 +5131,8 @@ static int update_size(mddev_t *mddev, sector_t num_sectors)
 			return -ENOSPC;
 	}
 	rv = mddev->pers->resize(mddev, num_sectors);
-	if (!rv) {
-		struct block_device *bdev;
-
-		bdev = bdget_disk(mddev->gendisk, 0);
-		if (bdev) {
-			mutex_lock(&bdev->bd_inode->i_mutex);
-			i_size_write(bdev->bd_inode,
-				     (loff_t)mddev->array_sectors << 9);
-			mutex_unlock(&bdev->bd_inode->i_mutex);
-			bdput(bdev);
-		}
-	}
+	if (!rv)
+		revalidate_disk(mddev->gendisk);
 	return rv;
 }
 
diff --git a/drivers/md/raid1.c b/drivers/md/raid1.c
index 67e794d0097..8726fd7ebce 100644
--- a/drivers/md/raid1.c
+++ b/drivers/md/raid1.c
@@ -2134,6 +2134,7 @@ static int raid1_resize(mddev_t *mddev, sector_t sectors)
 		return -EINVAL;
 	set_capacity(mddev->gendisk, mddev->array_sectors);
 	mddev->changed = 1;
+	revalidate_disk(mddev->gendisk);
 	if (sectors > mddev->dev_sectors &&
 	    mddev->recovery_cp == MaxSector) {
 		mddev->recovery_cp = mddev->dev_sectors;
diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index 2dc35b4c20a..2b521ee67df 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -4858,6 +4858,7 @@ static int raid5_resize(mddev_t *mddev, sector_t sectors)
 		return -EINVAL;
 	set_capacity(mddev->gendisk, mddev->array_sectors);
 	mddev->changed = 1;
+	revalidate_disk(mddev->gendisk);
 	if (sectors > mddev->dev_sectors && mddev->recovery_cp == MaxSector) {
 		mddev->recovery_cp = mddev->dev_sectors;
 		set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
@@ -5058,7 +5059,6 @@ static void end_reshape(raid5_conf_t *conf)
  */
 static void raid5_finish_reshape(mddev_t *mddev)
 {
-	struct block_device *bdev;
 	raid5_conf_t *conf = mddev->private;
 
 	if (!test_bit(MD_RECOVERY_INTR, &mddev->recovery)) {
@@ -5067,15 +5067,7 @@ static void raid5_finish_reshape(mddev_t *mddev)
 			md_set_array_sectors(mddev, raid5_size(mddev, 0, 0));
 			set_capacity(mddev->gendisk, mddev->array_sectors);
 			mddev->changed = 1;
-
-			bdev = bdget_disk(mddev->gendisk, 0);
-			if (bdev) {
-				mutex_lock(&bdev->bd_inode->i_mutex);
-				i_size_write(bdev->bd_inode,
-					     (loff_t)mddev->array_sectors << 9);
-				mutex_unlock(&bdev->bd_inode->i_mutex);
-				bdput(bdev);
-			}
+			revalidate_disk(mddev->gendisk);
 		} else {
 			int d;
 			mddev->degraded = conf->raid_disks;
-- 
GitLab


From a923c28fc538a4161b15e9b5d7d48248d73d3e6f Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Sun, 2 Aug 2009 19:17:15 -0700
Subject: [PATCH 0444/1153] sparc: Use page_fault_out_of_memory() for
 VM_FAULT_OOM.

As noted by Nick Piggin.

Signed-off-by: David S. Miller <davem@davemloft.net>
---
 arch/sparc/mm/fault_32.c | 7 ++++---
 arch/sparc/mm/fault_64.c | 7 ++++---
 2 files changed, 8 insertions(+), 6 deletions(-)

diff --git a/arch/sparc/mm/fault_32.c b/arch/sparc/mm/fault_32.c
index a5e30c642ee..b99f81c4906 100644
--- a/arch/sparc/mm/fault_32.c
+++ b/arch/sparc/mm/fault_32.c
@@ -319,9 +319,10 @@ no_context:
  */
 out_of_memory:
 	up_read(&mm->mmap_sem);
-	printk("VM: killing process %s\n", tsk->comm);
-	if (from_user)
-		do_group_exit(SIGKILL);
+	if (from_user) {
+		pagefault_out_of_memory();
+		return;
+	}
 	goto no_context;
 
 do_sigbus:
diff --git a/arch/sparc/mm/fault_64.c b/arch/sparc/mm/fault_64.c
index e5620b27c8b..43b0da96a4f 100644
--- a/arch/sparc/mm/fault_64.c
+++ b/arch/sparc/mm/fault_64.c
@@ -447,9 +447,10 @@ handle_kernel_fault:
 out_of_memory:
 	insn = get_fault_insn(regs, insn);
 	up_read(&mm->mmap_sem);
-	printk("VM: killing process %s\n", current->comm);
-	if (!(regs->tstate & TSTATE_PRIV))
-		do_group_exit(SIGKILL);
+	if (!(regs->tstate & TSTATE_PRIV)) {
+		pagefault_out_of_memory();
+		return;
+	}
 	goto handle_kernel_fault;
 
 intr_or_no_mm:
-- 
GitLab


From eb4ad826419ab5b1260bc1625249114767d36bea Mon Sep 17 00:00:00 2001
From: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Date: Sun, 2 Aug 2009 20:22:18 -0700
Subject: [PATCH 0445/1153] mlx4_en: Fix double pci unmapping.

In cases of fragmented skb, with the data pointers being wrapped around
the TX buffer, the completion handling code would not forward the data
pointer and the firs fragment was unmapped several times, while others
were not unmapped at all.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/mlx4/en_tx.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/mlx4/en_tx.c b/drivers/net/mlx4/en_tx.c
index 08c43f2ae72..5a88b3f5769 100644
--- a/drivers/net/mlx4/en_tx.c
+++ b/drivers/net/mlx4/en_tx.c
@@ -249,6 +249,7 @@ static u32 mlx4_en_free_tx_desc(struct mlx4_en_priv *priv,
 				pci_unmap_page(mdev->pdev,
 					(dma_addr_t) be64_to_cpu(data->addr),
 					 frag->size, PCI_DMA_TODEVICE);
+				++data;
 			}
 		}
 		/* Stamp the freed descriptor */
-- 
GitLab


From ce577e8cf5ddb4216553c9d563a9835d6de70ffa Mon Sep 17 00:00:00 2001
From: Takashi Iwai <tiwai@suse.de>
Date: Mon, 3 Aug 2009 08:23:52 +0200
Subject: [PATCH 0446/1153] ALSA: hda - Fix quirk for Toshiba Satellite
 A135-S4527

Use model=lenovo instead of model=dallas for Toshiba Satellite A135-S4527
with ALC861-VD codec.

Reference: Novell bnc#526325
	https://bugzilla.novell.com/show_bug.cgi?id=526325

Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/patch_realtek.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index b95df5d5dcc..f6b4cbf1ead 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -15157,7 +15157,7 @@ static struct snd_pci_quirk alc861vd_cfg_tbl[] = {
 	SND_PCI_QUIRK(0x10de, 0x03f0, "Realtek ALC660 demo", ALC660VD_3ST),
 	SND_PCI_QUIRK(0x1179, 0xff00, "Toshiba A135", ALC861VD_LENOVO),
 	/*SND_PCI_QUIRK(0x1179, 0xff00, "DALLAS", ALC861VD_DALLAS),*/ /*lenovo*/
-	SND_PCI_QUIRK(0x1179, 0xff01, "DALLAS", ALC861VD_DALLAS),
+	SND_PCI_QUIRK(0x1179, 0xff01, "Toshiba A135", ALC861VD_LENOVO),
 	SND_PCI_QUIRK(0x1179, 0xff03, "Toshiba P205", ALC861VD_LENOVO),
 	SND_PCI_QUIRK(0x1179, 0xff31, "Toshiba L30-149", ALC861VD_DALLAS),
 	SND_PCI_QUIRK(0x1565, 0x820d, "Biostar NF61S SE", ALC861VD_6ST_DIG),
-- 
GitLab


From deadff1665491afce124a8ff83f00f784161f660 Mon Sep 17 00:00:00 2001
From: Wu Fengguang <fengguang.wu@intel.com>
Date: Sat, 1 Aug 2009 18:45:16 +0800
Subject: [PATCH 0447/1153] ALSA: hda: track CIRB/CORB command/response states
 for each codec

Recently we hit a bug in our dev board, whose HDMI codec#3 may emit
redundant/spurious responses, which were then taken as responses to
command for another onboard Realtek codec#2, and mess up both codecs.

Extend the azx_rb.cmds and azx_rb.res to array and track each codec's
commands/responses separately. This helps keep good codec safe from
broken ones.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/hda_codec.c |  2 +-
 sound/pci/hda/hda_codec.h |  2 +-
 sound/pci/hda/hda_intel.c | 76 +++++++++++++++++++++++++++------------
 3 files changed, 56 insertions(+), 24 deletions(-)

diff --git a/sound/pci/hda/hda_codec.c b/sound/pci/hda/hda_codec.c
index 88480c0c58a..c7df01b72ca 100644
--- a/sound/pci/hda/hda_codec.c
+++ b/sound/pci/hda/hda_codec.c
@@ -174,7 +174,7 @@ static int codec_exec_verb(struct hda_codec *codec, unsigned int cmd,
 	mutex_lock(&bus->cmd_mutex);
 	err = bus->ops.command(bus, cmd);
 	if (!err && res)
-		*res = bus->ops.get_response(bus);
+		*res = bus->ops.get_response(bus, codec->addr);
 	mutex_unlock(&bus->cmd_mutex);
 	snd_hda_power_down(codec);
 	if (res && *res == -1 && bus->rirb_error) {
diff --git a/sound/pci/hda/hda_codec.h b/sound/pci/hda/hda_codec.h
index cad79efaabc..1b75f28ed09 100644
--- a/sound/pci/hda/hda_codec.h
+++ b/sound/pci/hda/hda_codec.h
@@ -568,7 +568,7 @@ struct hda_bus_ops {
 	/* send a single command */
 	int (*command)(struct hda_bus *bus, unsigned int cmd);
 	/* get a response from the last command */
-	unsigned int (*get_response)(struct hda_bus *bus);
+	unsigned int (*get_response)(struct hda_bus *bus, unsigned int addr);
 	/* free the private data */
 	void (*private_free)(struct hda_bus *);
 	/* attach a PCM stream */
diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c
index 77c1b840ca8..19e67a1b602 100644
--- a/sound/pci/hda/hda_intel.c
+++ b/sound/pci/hda/hda_intel.c
@@ -253,7 +253,7 @@ enum { SDI0, SDI1, SDI2, SDI3, SDO0, SDO1, SDO2, SDO3 };
 
 /* STATESTS int mask: S3,SD2,SD1,SD0 */
 #define AZX_MAX_CODECS		4
-#define STATESTS_INT_MASK	0x0f
+#define STATESTS_INT_MASK	((1 << AZX_MAX_CODECS) - 1)
 
 /* SD_CTL bits */
 #define SD_CTL_STREAM_RESET	0x01	/* stream reset bit */
@@ -361,8 +361,8 @@ struct azx_rb {
 	dma_addr_t addr;	/* physical address of CORB/RIRB buffer */
 	/* for RIRB */
 	unsigned short rp, wp;	/* read/write pointers */
-	int cmds;		/* number of pending requests */
-	u32 res;		/* last read value */
+	int cmds[AZX_MAX_CODECS];	/* number of pending requests */
+	u32 res[AZX_MAX_CODECS];	/* last read value */
 };
 
 struct azx {
@@ -531,7 +531,8 @@ static void azx_init_cmd_io(struct azx *chip)
 	/* RIRB set up */
 	chip->rirb.addr = chip->rb.addr + 2048;
 	chip->rirb.buf = (u32 *)(chip->rb.area + 2048);
-	chip->rirb.wp = chip->rirb.rp = chip->rirb.cmds = 0;
+	chip->rirb.wp = chip->rirb.rp = 0;
+	memset(chip->rirb.cmds, 0, sizeof(chip->rirb.cmds));
 	azx_writel(chip, RIRBLBASE, (u32)chip->rirb.addr);
 	azx_writel(chip, RIRBUBASE, upper_32_bits(chip->rirb.addr));
 
@@ -552,10 +553,35 @@ static void azx_free_cmd_io(struct azx *chip)
 	azx_writeb(chip, CORBCTL, 0);
 }
 
+static unsigned int azx_command_addr(u32 cmd)
+{
+	unsigned int addr = cmd >> 28;
+
+	if (addr >= AZX_MAX_CODECS) {
+		snd_BUG();
+		addr = 0;
+	}
+
+	return addr;
+}
+
+static unsigned int azx_response_addr(u32 res)
+{
+	unsigned int addr = res & 0xf;
+
+	if (addr >= AZX_MAX_CODECS) {
+		snd_BUG();
+		addr = 0;
+	}
+
+	return addr;
+}
+
 /* send a command */
 static int azx_corb_send_cmd(struct hda_bus *bus, u32 val)
 {
 	struct azx *chip = bus->private_data;
+	unsigned int addr = azx_command_addr(val);
 	unsigned int wp;
 
 	/* add command to corb */
@@ -564,7 +590,7 @@ static int azx_corb_send_cmd(struct hda_bus *bus, u32 val)
 	wp %= ICH6_MAX_CORB_ENTRIES;
 
 	spin_lock_irq(&chip->reg_lock);
-	chip->rirb.cmds++;
+	chip->rirb.cmds[addr]++;
 	chip->corb.buf[wp] = cpu_to_le32(val);
 	azx_writel(chip, CORBWP, wp);
 	spin_unlock_irq(&chip->reg_lock);
@@ -578,13 +604,14 @@ static int azx_corb_send_cmd(struct hda_bus *bus, u32 val)
 static void azx_update_rirb(struct azx *chip)
 {
 	unsigned int rp, wp;
+	unsigned int addr;
 	u32 res, res_ex;
 
 	wp = azx_readb(chip, RIRBWP);
 	if (wp == chip->rirb.wp)
 		return;
 	chip->rirb.wp = wp;
-		
+
 	while (chip->rirb.rp != wp) {
 		chip->rirb.rp++;
 		chip->rirb.rp %= ICH6_MAX_RIRB_ENTRIES;
@@ -592,18 +619,20 @@ static void azx_update_rirb(struct azx *chip)
 		rp = chip->rirb.rp << 1; /* an RIRB entry is 8-bytes */
 		res_ex = le32_to_cpu(chip->rirb.buf[rp + 1]);
 		res = le32_to_cpu(chip->rirb.buf[rp]);
+		addr = azx_response_addr(res_ex);
 		if (res_ex & ICH6_RIRB_EX_UNSOL_EV)
 			snd_hda_queue_unsol_event(chip->bus, res, res_ex);
-		else if (chip->rirb.cmds) {
-			chip->rirb.res = res;
+		else if (chip->rirb.cmds[addr]) {
+			chip->rirb.res[addr] = res;
 			smp_wmb();
-			chip->rirb.cmds--;
+			chip->rirb.cmds[addr]--;
 		}
 	}
 }
 
 /* receive a response */
-static unsigned int azx_rirb_get_response(struct hda_bus *bus)
+static unsigned int azx_rirb_get_response(struct hda_bus *bus,
+					  unsigned int addr)
 {
 	struct azx *chip = bus->private_data;
 	unsigned long timeout;
@@ -616,10 +645,10 @@ static unsigned int azx_rirb_get_response(struct hda_bus *bus)
 			azx_update_rirb(chip);
 			spin_unlock_irq(&chip->reg_lock);
 		}
-		if (!chip->rirb.cmds) {
+		if (!chip->rirb.cmds[addr]) {
 			smp_rmb();
 			bus->rirb_error = 0;
-			return chip->rirb.res; /* the last value */
+			return chip->rirb.res[addr]; /* the last value */
 		}
 		if (time_after(jiffies, timeout))
 			break;
@@ -692,7 +721,7 @@ static unsigned int azx_rirb_get_response(struct hda_bus *bus)
  */
 
 /* receive a response */
-static int azx_single_wait_for_response(struct azx *chip)
+static int azx_single_wait_for_response(struct azx *chip, unsigned int addr)
 {
 	int timeout = 50;
 
@@ -700,7 +729,7 @@ static int azx_single_wait_for_response(struct azx *chip)
 		/* check IRV busy bit */
 		if (azx_readw(chip, IRS) & ICH6_IRS_VALID) {
 			/* reuse rirb.res as the response return value */
-			chip->rirb.res = azx_readl(chip, IR);
+			chip->rirb.res[addr] = azx_readl(chip, IR);
 			return 0;
 		}
 		udelay(1);
@@ -708,7 +737,7 @@ static int azx_single_wait_for_response(struct azx *chip)
 	if (printk_ratelimit())
 		snd_printd(SFX "get_response timeout: IRS=0x%x\n",
 			   azx_readw(chip, IRS));
-	chip->rirb.res = -1;
+	chip->rirb.res[addr] = -1;
 	return -EIO;
 }
 
@@ -716,6 +745,7 @@ static int azx_single_wait_for_response(struct azx *chip)
 static int azx_single_send_cmd(struct hda_bus *bus, u32 val)
 {
 	struct azx *chip = bus->private_data;
+	unsigned int addr = azx_command_addr(val);
 	int timeout = 50;
 
 	bus->rirb_error = 0;
@@ -728,7 +758,7 @@ static int azx_single_send_cmd(struct hda_bus *bus, u32 val)
 			azx_writel(chip, IC, val);
 			azx_writew(chip, IRS, azx_readw(chip, IRS) |
 				   ICH6_IRS_BUSY);
-			return azx_single_wait_for_response(chip);
+			return azx_single_wait_for_response(chip, addr);
 		}
 		udelay(1);
 	}
@@ -739,10 +769,11 @@ static int azx_single_send_cmd(struct hda_bus *bus, u32 val)
 }
 
 /* receive a response */
-static unsigned int azx_single_get_response(struct hda_bus *bus)
+static unsigned int azx_single_get_response(struct hda_bus *bus,
+					    unsigned int addr)
 {
 	struct azx *chip = bus->private_data;
-	return chip->rirb.res;
+	return chip->rirb.res[addr];
 }
 
 /*
@@ -765,13 +796,14 @@ static int azx_send_cmd(struct hda_bus *bus, unsigned int val)
 }
 
 /* get a response */
-static unsigned int azx_get_response(struct hda_bus *bus)
+static unsigned int azx_get_response(struct hda_bus *bus,
+				     unsigned int addr)
 {
 	struct azx *chip = bus->private_data;
 	if (chip->single_cmd)
-		return azx_single_get_response(bus);
+		return azx_single_get_response(bus, addr);
 	else
-		return azx_rirb_get_response(bus);
+		return azx_rirb_get_response(bus, addr);
 }
 
 #ifdef CONFIG_SND_HDA_POWER_SAVE
@@ -1245,7 +1277,7 @@ static int probe_codec(struct azx *chip, int addr)
 
 	chip->probing = 1;
 	azx_send_cmd(chip->bus, cmd);
-	res = azx_get_response(chip->bus);
+	res = azx_get_response(chip->bus, addr);
 	chip->probing = 0;
 	if (res == -1)
 		return -EIO;
-- 
GitLab


From a678cdee25a387c8fc3b2754974695412baf1d85 Mon Sep 17 00:00:00 2001
From: Wu Fengguang <fengguang.wu@intel.com>
Date: Sat, 1 Aug 2009 18:46:46 +0800
Subject: [PATCH 0448/1153] ALSA: hda: take cmd_mutex in probe_codec()

Now that each codec will have its own module, it is possible
for the user to load one codec while another one is running.

So cmd_mutex would be a safe addition to probe_codec().

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/hda_intel.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c
index 19e67a1b602..ddabc827ac4 100644
--- a/sound/pci/hda/hda_intel.c
+++ b/sound/pci/hda/hda_intel.c
@@ -1275,10 +1275,12 @@ static int probe_codec(struct azx *chip, int addr)
 		(AC_VERB_PARAMETERS << 8) | AC_PAR_VENDOR_ID;
 	unsigned int res;
 
+	mutex_lock(&chip->bus->cmd_mutex);
 	chip->probing = 1;
 	azx_send_cmd(chip->bus, cmd);
 	res = azx_get_response(chip->bus, addr);
 	chip->probing = 0;
+	mutex_unlock(&chip->bus->cmd_mutex);
 	if (res == -1)
 		return -EIO;
 	snd_printdd(SFX "codec #%d probed OK\n", addr);
-- 
GitLab


From cdb1fbf23181c133fb24f12ad14ccea7dc399599 Mon Sep 17 00:00:00 2001
From: Wu Fengguang <fengguang.wu@intel.com>
Date: Sat, 1 Aug 2009 18:47:41 +0800
Subject: [PATCH 0449/1153] ALSA: hda: take reg_lock in
 azx_init_cmd_io/azx_free_cmd_io

Just for safety.  azx_init_cmd_io() and azx_free_cmd_io() may be
called when switching to single command mode.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/hda_intel.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c
index ddabc827ac4..b6e6314d006 100644
--- a/sound/pci/hda/hda_intel.c
+++ b/sound/pci/hda/hda_intel.c
@@ -513,6 +513,7 @@ static int azx_alloc_cmd_io(struct azx *chip)
 
 static void azx_init_cmd_io(struct azx *chip)
 {
+	spin_lock_irq(&chip->reg_lock);
 	/* CORB set up */
 	chip->corb.addr = chip->rb.addr;
 	chip->corb.buf = (u32 *)chip->rb.area;
@@ -544,13 +545,16 @@ static void azx_init_cmd_io(struct azx *chip)
 	azx_writew(chip, RINTCNT, 1);
 	/* enable rirb dma and response irq */
 	azx_writeb(chip, RIRBCTL, ICH6_RBCTL_DMA_EN | ICH6_RBCTL_IRQ_EN);
+	spin_unlock_irq(&chip->reg_lock);
 }
 
 static void azx_free_cmd_io(struct azx *chip)
 {
+	spin_lock_irq(&chip->reg_lock);
 	/* disable ringbuffer DMAs */
 	azx_writeb(chip, RIRBCTL, 0);
 	azx_writeb(chip, CORBCTL, 0);
+	spin_unlock_irq(&chip->reg_lock);
 }
 
 static unsigned int azx_command_addr(u32 cmd)
-- 
GitLab


From c32649feb4573b31f0a2bfdf35cbe1351256c764 Mon Sep 17 00:00:00 2001
From: Wu Fengguang <fengguang.wu@intel.com>
Date: Sat, 1 Aug 2009 18:48:12 +0800
Subject: [PATCH 0450/1153] ALSA: hda: read CORBWP inside reg_lock

This converts the last CORBWP access outside of reg_lock.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/hda_intel.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c
index b6e6314d006..df6d9820efa 100644
--- a/sound/pci/hda/hda_intel.c
+++ b/sound/pci/hda/hda_intel.c
@@ -588,15 +588,17 @@ static int azx_corb_send_cmd(struct hda_bus *bus, u32 val)
 	unsigned int addr = azx_command_addr(val);
 	unsigned int wp;
 
+	spin_lock_irq(&chip->reg_lock);
+
 	/* add command to corb */
 	wp = azx_readb(chip, CORBWP);
 	wp++;
 	wp %= ICH6_MAX_CORB_ENTRIES;
 
-	spin_lock_irq(&chip->reg_lock);
 	chip->rirb.cmds[addr]++;
 	chip->corb.buf[wp] = cpu_to_le32(val);
 	azx_writel(chip, CORBWP, wp);
+
 	spin_unlock_irq(&chip->reg_lock);
 
 	return 0;
-- 
GitLab


From feb273404f15d86098cb0e81e46330d5c1e22b1b Mon Sep 17 00:00:00 2001
From: Wu Fengguang <fengguang.wu@intel.com>
Date: Sat, 1 Aug 2009 19:17:14 +0800
Subject: [PATCH 0451/1153] ALSA: hda: remember last command for each codec

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/hda_intel.c | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)

diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c
index df6d9820efa..7c43f92de2f 100644
--- a/sound/pci/hda/hda_intel.c
+++ b/sound/pci/hda/hda_intel.c
@@ -418,7 +418,7 @@ struct azx {
 	unsigned int probing :1; /* codec probing phase */
 
 	/* for debugging */
-	unsigned int last_cmd;	/* last issued command (to sync) */
+	unsigned int last_cmd[AZX_MAX_CODECS];
 
 	/* for pending irqs */
 	struct work_struct irq_pending_work;
@@ -668,7 +668,8 @@ static unsigned int azx_rirb_get_response(struct hda_bus *bus,
 
 	if (chip->msi) {
 		snd_printk(KERN_WARNING SFX "No response from codec, "
-			   "disabling MSI: last cmd=0x%08x\n", chip->last_cmd);
+			   "disabling MSI: last cmd=0x%08x\n",
+			   chip->last_cmd[addr]);
 		free_irq(chip->irq, chip);
 		chip->irq = -1;
 		pci_disable_msi(chip->pci);
@@ -683,7 +684,7 @@ static unsigned int azx_rirb_get_response(struct hda_bus *bus,
 	if (!chip->polling_mode) {
 		snd_printk(KERN_WARNING SFX "azx_get_response timeout, "
 			   "switching to polling mode: last cmd=0x%08x\n",
-			   chip->last_cmd);
+			   chip->last_cmd[addr]);
 		chip->polling_mode = 1;
 		goto again;
 	}
@@ -707,7 +708,7 @@ static unsigned int azx_rirb_get_response(struct hda_bus *bus,
 
 	snd_printk(KERN_ERR "hda_intel: azx_get_response timeout, "
 		   "switching to single_cmd mode: last cmd=0x%08x\n",
-		   chip->last_cmd);
+		   chip->last_cmd[addr]);
 	chip->single_cmd = 1;
 	bus->response_reset = 0;
 	/* re-initialize CORB/RIRB */
@@ -794,7 +795,7 @@ static int azx_send_cmd(struct hda_bus *bus, unsigned int val)
 {
 	struct azx *chip = bus->private_data;
 
-	chip->last_cmd = val;
+	chip->last_cmd[azx_command_addr(val)] = val;
 	if (chip->single_cmd)
 		return azx_single_send_cmd(bus, val);
 	else
-- 
GitLab


From e310bb0646e57a4f9182865115c5780931456c65 Mon Sep 17 00:00:00 2001
From: Wu Fengguang <fengguang.wu@intel.com>
Date: Sat, 1 Aug 2009 19:18:45 +0800
Subject: [PATCH 0452/1153] ALSA: hda: warn on spurious response

To help disclose hardware bugs.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/hda_intel.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c
index 7c43f92de2f..175f07a381b 100644
--- a/sound/pci/hda/hda_intel.c
+++ b/sound/pci/hda/hda_intel.c
@@ -632,7 +632,11 @@ static void azx_update_rirb(struct azx *chip)
 			chip->rirb.res[addr] = res;
 			smp_wmb();
 			chip->rirb.cmds[addr]--;
-		}
+		} else
+			snd_printk(KERN_ERR SFX "spurious response %#x:%#x, "
+				   "last cmd=%#08x\n",
+				   res, res_ex,
+				   chip->last_cmd[addr]);
 	}
 }
 
-- 
GitLab


From 84d3dc200fc8b878acf7c1840b238e6a0450e4d0 Mon Sep 17 00:00:00 2001
From: Chengu Wang <wangchengu@gmail.com>
Date: Thu, 30 Jul 2009 19:43:55 +0800
Subject: [PATCH 0453/1153] ALSA: hda: Correct EAPD for Dell Inspiron 1525

The commit 24918b61b55c21e09a3e07cd82e1b3a8154782dc statically changes
the model from dell-bios to dell-3stack to solve the sound decreasing
regression (http://lkml.org/lkml/2008/9/12/203), however it leads to another
problem that the 2nd headphone jack doesn't work
(https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3987). So I think
the commit 249**2dc is just a workaround. I would like to give a true solution
here.

The datasheet for STAC9228 says, GPIO2 is the same pin as VOL DOWN, and
the EAPD pin is GPIO0. This is why the sound decreases if we set EAPD as
GPIO2. This patch changes EAPD to GPIO0 to solve the problem.

Signed-off-by: Chengu Wang <wangchengu@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/patch_sigmatel.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c
index 5383d8cff88..456ef6ac12e 100644
--- a/sound/pci/hda/patch_sigmatel.c
+++ b/sound/pci/hda/patch_sigmatel.c
@@ -2266,7 +2266,7 @@ static struct snd_pci_quirk stac927x_cfg_tbl[] = {
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL,  0x01f3, "Dell Inspiron 1420", STAC_DELL_BIOS),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL,  0x0227, "Dell Vostro 1400  ", STAC_DELL_BIOS),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL,  0x022e, "Dell     ", STAC_DELL_BIOS),
-	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL,  0x022f, "Dell Inspiron 1525", STAC_DELL_3ST),
+	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL,  0x022f, "Dell Inspiron 1525", STAC_DELL_BIOS),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL,  0x0242, "Dell     ", STAC_DELL_BIOS),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL,  0x0243, "Dell     ", STAC_DELL_BIOS),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL,  0x02ff, "Dell     ", STAC_DELL_BIOS),
@@ -5645,6 +5645,13 @@ static int patch_stac927x(struct hda_codec *codec)
 		/* GPIO2 High = Enable EAPD */
 		spec->eapd_mask = spec->gpio_mask = spec->gpio_dir = 0x04;
 		spec->gpio_data = 0x04;
+		switch (codec->subsystem_id) {
+		case 0x1028022f:
+			/* correct EAPD to be GPIO0 */
+			spec->eapd_mask = spec->gpio_mask = 0x01;
+			spec->gpio_dir = spec->gpio_data = 0x01;
+			break;
+		};
 		spec->dmic_nids = stac927x_dmic_nids;
 		spec->num_dmics = STAC927X_NUM_DMICS;
 
-- 
GitLab


From 4b35d2ca2307d40ccb6b3b6f9cc25ac9178b2a6c Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Sun, 2 Aug 2009 13:30:45 +0200
Subject: [PATCH 0454/1153] ALSA: hda - Read buffer overflow

Check whether index is within bounds before testing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/patch_realtek.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index f6b4cbf1ead..51c44fdbc0f 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -559,7 +559,7 @@ static int alc_pin_mode_get(struct snd_kcontrol *kcontrol,
 
 	/* Find enumerated value for current pinctl setting */
 	i = alc_pin_mode_min(dir);
-	while (alc_pin_mode_values[i] != pinctl && i <= alc_pin_mode_max(dir))
+	while (i <= alc_pin_mode_max(dir) && alc_pin_mode_values[i] != pinctl)
 		i++;
 	*valp = i <= alc_pin_mode_max(dir) ? i: alc_pin_mode_min(dir);
 	return 0;
-- 
GitLab


From 7699ad35ed06044c4fc1be162553880f98658616 Mon Sep 17 00:00:00 2001
From: Nicolas Pitre <nico@cam.org>
Date: Mon, 15 Jun 2009 01:10:18 -0400
Subject: [PATCH 0455/1153] mtd: let include/linux/mtd/partitions.h stand on
 its own

When declaring static MTD partitions in board specific code, only
including <include/linux/mtd/partitions.h> should suffice without
gcc nagging us with:

In file included from arch/arm/mach-kirkwood/sheevaplug-setup.c:14:
include/linux/mtd/partitions.h:50: warning: 'struct mtd_info' declared inside parameter list
include/linux/mtd/partitions.h:50: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/mtd/partitions.h:51: warning: 'struct mtd_info' declared inside parameter list
include/linux/mtd/partitions.h:61: warning: 'struct mtd_info' declared inside parameter list
include/linux/mtd/partitions.h:67: warning: 'struct mtd_info' declared inside parameter list

Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 include/linux/mtd/partitions.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/include/linux/mtd/partitions.h b/include/linux/mtd/partitions.h
index af6dcb992bc..b70313d33ff 100644
--- a/include/linux/mtd/partitions.h
+++ b/include/linux/mtd/partitions.h
@@ -47,6 +47,8 @@ struct mtd_partition {
 #define MTDPART_SIZ_FULL	(0)
 
 
+struct mtd_info;
+
 int add_mtd_partitions(struct mtd_info *, const struct mtd_partition *, int);
 int del_mtd_partitions(struct mtd_info *);
 
-- 
GitLab


From 6afc4fdb3e94ba60cd566cb878b60c6c01979277 Mon Sep 17 00:00:00 2001
From: Saeed Bishara <saeed@marvell.com>
Date: Tue, 28 Jul 2009 04:56:43 -0700
Subject: [PATCH 0456/1153] mtd: fix the conversion from dev to mtd_info

The patch fixes a bug when converting dev to mtd_info by using the
drvdata of the dev, the previous code used
container_of(dev, struct mtd_info, dev), but won't work for the mtdXro
devices as they created without being contained inside mtd_info structure.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 drivers/mtd/mtdcore.c   | 7 ++++---
 include/linux/mtd/mtd.h | 2 +-
 2 files changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/mtd/mtdcore.c b/drivers/mtd/mtdcore.c
index fac54a3fa3f..00ebf7af746 100644
--- a/drivers/mtd/mtdcore.c
+++ b/drivers/mtd/mtdcore.c
@@ -65,8 +65,8 @@ static void mtd_release(struct device *dev)
 static int mtd_cls_suspend(struct device *dev, pm_message_t state)
 {
 	struct mtd_info *mtd = dev_to_mtd(dev);
-	
-	if (mtd->suspend)
+
+	if (mtd && mtd->suspend)
 		return mtd->suspend(mtd);
 	else
 		return 0;
@@ -76,7 +76,7 @@ static int mtd_cls_resume(struct device *dev)
 {
 	struct mtd_info *mtd = dev_to_mtd(dev);
 	
-	if (mtd->resume)
+	if (mtd && mtd->resume)
 		mtd->resume(mtd);
 	return 0;
 }
@@ -298,6 +298,7 @@ int add_mtd_device(struct mtd_info *mtd)
 			mtd->dev.class = &mtd_class;
 			mtd->dev.devt = MTD_DEVT(i);
 			dev_set_name(&mtd->dev, "mtd%d", i);
+			dev_set_drvdata(&mtd->dev, mtd);
 			if (device_register(&mtd->dev) != 0) {
 				mtd_table[i] = NULL;
 				break;
diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h
index 5675b63a063..0f32a9b6ff5 100644
--- a/include/linux/mtd/mtd.h
+++ b/include/linux/mtd/mtd.h
@@ -251,7 +251,7 @@ struct mtd_info {
 
 static inline struct mtd_info *dev_to_mtd(struct device *dev)
 {
-	return dev ? container_of(dev, struct mtd_info, dev) : NULL;
+	return dev ? dev_get_drvdata(dev) : NULL;
 }
 
 static inline uint32_t mtd_div_by_eb(uint64_t sz, struct mtd_info *mtd)
-- 
GitLab


From 8022c13c27b822cf22f13df10b42aae89cd56bf0 Mon Sep 17 00:00:00 2001
From: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Date: Fri, 10 Jul 2009 17:02:17 +0300
Subject: [PATCH 0457/1153] mtd: blkdevs: do not forget to get MTD devices

Nowadays MTD devices have to be "get" before they can be
used. This has to be done with 'get_mtd_device()'. The
'blktrans_open()' function did not do this and instead
used 'try_module_get()'. Fix this.

Since 'get_mtd_device()' already gets the module, extra
'try_module_get()' is not needed.

This fixes oops when one tries to use mtdblock on top of
gluebi.

Reported-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 drivers/mtd/mtd_blkdevs.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/mtd/mtd_blkdevs.c b/drivers/mtd/mtd_blkdevs.c
index c3f62654b6d..7baba40c1ed 100644
--- a/drivers/mtd/mtd_blkdevs.c
+++ b/drivers/mtd/mtd_blkdevs.c
@@ -144,7 +144,7 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode)
 	struct mtd_blktrans_ops *tr = dev->tr;
 	int ret = -ENODEV;
 
-	if (!try_module_get(dev->mtd->owner))
+	if (!get_mtd_device(NULL, dev->mtd->index))
 		goto out;
 
 	if (!try_module_get(tr->owner))
@@ -158,7 +158,7 @@ static int blktrans_open(struct block_device *bdev, fmode_t mode)
 	ret = 0;
 	if (tr->open && (ret = tr->open(dev))) {
 		dev->mtd->usecount--;
-		module_put(dev->mtd->owner);
+		put_mtd_device(dev->mtd);
 	out_tr:
 		module_put(tr->owner);
 	}
@@ -177,7 +177,7 @@ static int blktrans_release(struct gendisk *disk, fmode_t mode)
 
 	if (!ret) {
 		dev->mtd->usecount--;
-		module_put(dev->mtd->owner);
+		put_mtd_device(dev->mtd);
 		module_put(tr->owner);
 	}
 
-- 
GitLab


From 00acf4a80779611a7ea77ff5b5ffab886ed5cc42 Mon Sep 17 00:00:00 2001
From: Mika Korhonen <mika.j.korhonen@gmail.com>
Date: Thu, 11 Jun 2009 14:05:07 +0300
Subject: [PATCH 0458/1153] mtd: OneNAND: fix incorrect bufferram offset

Fixes the case where CONFIG_MTD_ONENAND_2X_PROGRAM is set and
the real page size differs from mtd_info.writesize.

Signed-off-by: Mika Korhonen <mika.j.korhonen@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 drivers/mtd/onenand/omap2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c
index 38d656b9b2e..6fac1f496d4 100644
--- a/drivers/mtd/onenand/omap2.c
+++ b/drivers/mtd/onenand/omap2.c
@@ -266,7 +266,7 @@ static inline int omap2_onenand_bufferram_offset(struct mtd_info *mtd, int area)
 
 	if (ONENAND_CURRENT_BUFFERRAM(this)) {
 		if (area == ONENAND_DATARAM)
-			return mtd->writesize;
+			return this->writesize;
 		if (area == ONENAND_SPARERAM)
 			return mtd->oobsize;
 	}
-- 
GitLab


From 3cae1cc149c40c14424162496eb5a7c8db1cd4fb Mon Sep 17 00:00:00 2001
From: Mika Korhonen <ext-mika.2.korhonen@nokia.com>
Date: Thu, 25 Jun 2009 15:32:19 +0300
Subject: [PATCH 0459/1153] mtd: OneNAND: OMAP2/3: free GPMC CS on module
 removal

GPMC CS was not freed in omap2_onenand_remove() preventing the module
from reloading after removal.

Signed-off-by: Mika Korhonen <ext-mika.2.korhonen@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 drivers/mtd/onenand/omap2.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/mtd/onenand/omap2.c b/drivers/mtd/onenand/omap2.c
index 6fac1f496d4..0108ed42e87 100644
--- a/drivers/mtd/onenand/omap2.c
+++ b/drivers/mtd/onenand/omap2.c
@@ -770,6 +770,7 @@ static int __devexit omap2_onenand_remove(struct platform_device *pdev)
 	}
 	iounmap(c->onenand.base);
 	release_mem_region(c->phys_base, ONENAND_IO_SIZE);
+	gpmc_cs_free(c->gpmc_cs);
 	kfree(c);
 
 	return 0;
-- 
GitLab


From 2bf961b7ccd69e108ac435c67e2b0522b403c578 Mon Sep 17 00:00:00 2001
From: Subrata Modak <subrata@linux.vnet.ibm.com>
Date: Wed, 1 Jul 2009 19:22:47 +0530
Subject: [PATCH 0460/1153] mtd: remove 'SBC8240 Wind River' Device Driver Code

This driver is causing build errors and is no longer needed -- it is obsoleted
by physmap_of.

Signed-off-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Tested-on-PPC64-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 drivers/mtd/maps/Kconfig   |   7 --
 drivers/mtd/maps/Makefile  |   1 -
 drivers/mtd/maps/sbc8240.c | 250 -------------------------------------
 3 files changed, 258 deletions(-)

diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index 0b98654d8ee..7a58bd5522f 100644
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -284,13 +284,6 @@ config MTD_L440GX
 
 	  BE VERY CAREFUL.
 
-config MTD_SBC8240
-	tristate "Flash device on SBC8240"
-	depends on MTD_JEDECPROBE && 8260
-	help
-          Flash access on the SBC8240 board from Wind River.  See
-          <http://www.windriver.com/products/sbc8240/>
-
 config MTD_TQM8XXL
 	tristate "CFI Flash device mapped on TQM8XXL"
 	depends on MTD_CFI && TQM8xxL
diff --git a/drivers/mtd/maps/Makefile b/drivers/mtd/maps/Makefile
index 8bae7f9850c..5beb0662d72 100644
--- a/drivers/mtd/maps/Makefile
+++ b/drivers/mtd/maps/Makefile
@@ -50,7 +50,6 @@ obj-$(CONFIG_MTD_UCLINUX)	+= uclinux.o
 obj-$(CONFIG_MTD_NETtel)	+= nettel.o
 obj-$(CONFIG_MTD_SCB2_FLASH)	+= scb2_flash.o
 obj-$(CONFIG_MTD_H720X)		+= h720x-flash.o
-obj-$(CONFIG_MTD_SBC8240)	+= sbc8240.o
 obj-$(CONFIG_MTD_IXP4XX)	+= ixp4xx.o
 obj-$(CONFIG_MTD_IXP2000)	+= ixp2000.o
 obj-$(CONFIG_MTD_WRSBC8260)	+= wr_sbc82xx_flash.o
diff --git a/drivers/mtd/maps/sbc8240.c b/drivers/mtd/maps/sbc8240.c
index d5374cdcb16..e69de29bb2d 100644
--- a/drivers/mtd/maps/sbc8240.c
+++ b/drivers/mtd/maps/sbc8240.c
@@ -1,250 +0,0 @@
-/*
- * Handle mapping of the flash memory access routines on the SBC8240 board.
- *
- * Carolyn Smith, Tektronix, Inc.
- *
- * This code is GPLed
- */
-
-/*
- * The SBC8240 has 2 flash banks.
- * Bank 0 is a 512 KiB AMD AM29F040B; 8 x 64 KiB sectors.
- * It contains the U-Boot code (7 sectors) and the environment (1 sector).
- * Bank 1 is 4 x 1 MiB AMD AM29LV800BT; 15 x 64 KiB sectors, 1 x 32 KiB sector,
- * 2 x 8 KiB sectors, 1 x 16 KiB sectors.
- * Both parts are JEDEC compatible.
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <asm/io.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/mtd/cfi.h>
-
-#ifdef CONFIG_MTD_PARTITIONS
-#include <linux/mtd/partitions.h>
-#endif
-
-#define	DEBUG
-
-#ifdef	DEBUG
-# define debugk(fmt,args...)	printk(fmt ,##args)
-#else
-# define debugk(fmt,args...)
-#endif
-
-
-#define WINDOW_ADDR0	0xFFF00000		/* 512 KiB */
-#define WINDOW_SIZE0	0x00080000
-#define BUSWIDTH0	1
-
-#define WINDOW_ADDR1	0xFF000000		/* 4 MiB */
-#define WINDOW_SIZE1	0x00400000
-#define BUSWIDTH1	8
-
-#define MSG_PREFIX "sbc8240:"	/* prefix for our printk()'s */
-#define MTDID	   "sbc8240-%d"	/* for mtdparts= partitioning */
-
-
-static struct map_info sbc8240_map[2] = {
-	{
-		.name           = "sbc8240 Flash Bank #0",
-		.size           = WINDOW_SIZE0,
-		.bankwidth       = BUSWIDTH0,
-	},
-	{
-		.name           = "sbc8240 Flash Bank #1",
-		.size           = WINDOW_SIZE1,
-		.bankwidth       = BUSWIDTH1,
-	}
-};
-
-#define NUM_FLASH_BANKS	ARRAY_SIZE(sbc8240_map)
-
-/*
- * The following defines the partition layout of SBC8240 boards.
- *
- * See include/linux/mtd/partitions.h for definition of the
- * mtd_partition structure.
- *
- * The *_max_flash_size is the maximum possible mapped flash size
- * which is not necessarily the actual flash size. It must correspond
- * to the value specified in the mapping definition defined by the
- * "struct map_desc *_io_desc" for the corresponding machine.
- */
-
-#ifdef CONFIG_MTD_PARTITIONS
-
-static struct mtd_partition sbc8240_uboot_partitions [] = {
-	/* Bank 0 */
-	{
-		.name =	"U-boot",			/* U-Boot Firmware	*/
-		.offset =	0,
-		.size =	0x00070000,			/*  7 x 64 KiB sectors 	*/
-		.mask_flags = MTD_WRITEABLE,		/*  force read-only	*/
-	},
-	{
-		.name =	"environment",			/* U-Boot environment	*/
-		.offset =	0x00070000,
-		.size =	0x00010000,			/*  1 x 64 KiB sector	*/
-	},
-};
-
-static struct mtd_partition sbc8240_fs_partitions [] = {
-	{
-		.name =	"jffs",				/* JFFS  filesystem	*/
-		.offset =	0,
-		.size =	0x003C0000,			/*  4 * 15 * 64KiB	*/
-	},
-	{
-		.name =	"tmp32",
-		.offset =	0x003C0000,
-		.size =	0x00020000,			/*  4 * 32KiB		*/
-	},
-	{
-		.name =	"tmp8a",
-		.offset =	0x003E0000,
-		.size =	0x00008000,			/*  4 * 8KiB		*/
-	},
-	{
-		.name =	"tmp8b",
-		.offset =	0x003E8000,
-		.size =	0x00008000,			/*  4 * 8KiB		*/
-	},
-	{
-		.name =	"tmp16",
-		.offset =	0x003F0000,
-		.size =	0x00010000,			/*  4 * 16KiB		*/
-	}
-};
-
-/* trivial struct to describe partition information */
-struct mtd_part_def
-{
-	int nums;
-	unsigned char *type;
-	struct mtd_partition* mtd_part;
-};
-
-static struct mtd_info *sbc8240_mtd[NUM_FLASH_BANKS];
-static struct mtd_part_def sbc8240_part_banks[NUM_FLASH_BANKS];
-
-
-#endif	/* CONFIG_MTD_PARTITIONS */
-
-
-static int __init init_sbc8240_mtd (void)
-{
-	static struct _cjs {
-		u_long addr;
-		u_long size;
-	} pt[NUM_FLASH_BANKS] = {
-		{
-			.addr = WINDOW_ADDR0,
-			.size = WINDOW_SIZE0
-		},
-		{
-			.addr = WINDOW_ADDR1,
-			.size = WINDOW_SIZE1
-		},
-	};
-
-	int devicesfound = 0;
-	int i,j;
-
-	for (i = 0; i < NUM_FLASH_BANKS; i++) {
-		printk (KERN_NOTICE MSG_PREFIX
-			"Probing 0x%08lx at 0x%08lx\n", pt[i].size, pt[i].addr);
-
-		sbc8240_map[i].map_priv_1 =
-			(unsigned long) ioremap (pt[i].addr, pt[i].size);
-		if (!sbc8240_map[i].map_priv_1) {
-			printk (MSG_PREFIX "failed to ioremap\n");
-			for (j = 0; j < i; j++) {
-				iounmap((void *) sbc8240_map[j].map_priv_1);
-				sbc8240_map[j].map_priv_1 = 0;
-			}
-			return -EIO;
-		}
-		simple_map_init(&sbc8240_mtd[i]);
-
-		sbc8240_mtd[i] = do_map_probe("jedec_probe", &sbc8240_map[i]);
-
-		if (sbc8240_mtd[i]) {
-			sbc8240_mtd[i]->module = THIS_MODULE;
-			devicesfound++;
-		} else {
-			if (sbc8240_map[i].map_priv_1) {
-				iounmap((void *) sbc8240_map[i].map_priv_1);
-				sbc8240_map[i].map_priv_1 = 0;
-			}
-		}
-	}
-
-	if (!devicesfound) {
-		printk(KERN_NOTICE MSG_PREFIX
-		       "No suppported flash chips found!\n");
-		return -ENXIO;
-	}
-
-#ifdef CONFIG_MTD_PARTITIONS
-	sbc8240_part_banks[0].mtd_part   = sbc8240_uboot_partitions;
-	sbc8240_part_banks[0].type       = "static image";
-	sbc8240_part_banks[0].nums       = ARRAY_SIZE(sbc8240_uboot_partitions);
-	sbc8240_part_banks[1].mtd_part   = sbc8240_fs_partitions;
-	sbc8240_part_banks[1].type       = "static file system";
-	sbc8240_part_banks[1].nums       = ARRAY_SIZE(sbc8240_fs_partitions);
-
-	for (i = 0; i < NUM_FLASH_BANKS; i++) {
-
-		if (!sbc8240_mtd[i]) continue;
-		if (sbc8240_part_banks[i].nums == 0) {
-			printk (KERN_NOTICE MSG_PREFIX
-				"No partition info available, registering whole device\n");
-			add_mtd_device(sbc8240_mtd[i]);
-		} else {
-			printk (KERN_NOTICE MSG_PREFIX
-				"Using %s partition definition\n", sbc8240_part_banks[i].mtd_part->name);
-			add_mtd_partitions (sbc8240_mtd[i],
-					    sbc8240_part_banks[i].mtd_part,
-					    sbc8240_part_banks[i].nums);
-		}
-	}
-#else
-	printk(KERN_NOTICE MSG_PREFIX
-	       "Registering %d flash banks at once\n", devicesfound);
-
-	for (i = 0; i < devicesfound; i++) {
-		add_mtd_device(sbc8240_mtd[i]);
-	}
-#endif	/* CONFIG_MTD_PARTITIONS */
-
-	return devicesfound == 0 ? -ENXIO : 0;
-}
-
-static void __exit cleanup_sbc8240_mtd (void)
-{
-	int i;
-
-	for (i = 0; i < NUM_FLASH_BANKS; i++) {
-		if (sbc8240_mtd[i]) {
-			del_mtd_device (sbc8240_mtd[i]);
-			map_destroy (sbc8240_mtd[i]);
-		}
-		if (sbc8240_map[i].map_priv_1) {
-			iounmap ((void *) sbc8240_map[i].map_priv_1);
-			sbc8240_map[i].map_priv_1 = 0;
-		}
-	}
-}
-
-module_init (init_sbc8240_mtd);
-module_exit (cleanup_sbc8240_mtd);
-
-MODULE_LICENSE ("GPL");
-MODULE_AUTHOR ("Carolyn Smith <carolyn.smith@tektronix.com>");
-MODULE_DESCRIPTION ("MTD map driver for SBC8240 boards");
-
-- 
GitLab


From d676c11727815761e41a81b00c054b4bec452ae5 Mon Sep 17 00:00:00 2001
From: Matthias Kaehlcke <matthias@kaehlcke.net>
Date: Tue, 14 Jul 2009 22:04:29 +0200
Subject: [PATCH 0461/1153] mtd: mtdblock: introduce mtdblks_lock

The mtdblks array and its content are prone to race conditions. Introduce
the mutex mtdblks_lock in order to solve this.

[Amended by Artem Bityutskiy]

Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 drivers/mtd/mtdblock.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/mtdblock.c b/drivers/mtd/mtdblock.c
index 208c6faa035..77db5ce24d9 100644
--- a/drivers/mtd/mtdblock.c
+++ b/drivers/mtd/mtdblock.c
@@ -29,6 +29,8 @@ static struct mtdblk_dev {
 	enum { STATE_EMPTY, STATE_CLEAN, STATE_DIRTY } cache_state;
 } *mtdblks[MAX_MTD_DEVICES];
 
+static struct mutex mtdblks_lock;
+
 /*
  * Cache stuff...
  *
@@ -270,15 +272,19 @@ static int mtdblock_open(struct mtd_blktrans_dev *mbd)
 
 	DEBUG(MTD_DEBUG_LEVEL1,"mtdblock_open\n");
 
+	mutex_lock(&mtdblks_lock);
 	if (mtdblks[dev]) {
 		mtdblks[dev]->count++;
+		mutex_unlock(&mtdblks_lock);
 		return 0;
 	}
 
 	/* OK, it's not open. Create cache info for it */
 	mtdblk = kzalloc(sizeof(struct mtdblk_dev), GFP_KERNEL);
-	if (!mtdblk)
+	if (!mtdblk) {
+		mutex_unlock(&mtdblks_lock);
 		return -ENOMEM;
+	}
 
 	mtdblk->count = 1;
 	mtdblk->mtd = mtd;
@@ -291,6 +297,7 @@ static int mtdblock_open(struct mtd_blktrans_dev *mbd)
 	}
 
 	mtdblks[dev] = mtdblk;
+	mutex_unlock(&mtdblks_lock);
 
 	DEBUG(MTD_DEBUG_LEVEL1, "ok\n");
 
@@ -304,6 +311,8 @@ static int mtdblock_release(struct mtd_blktrans_dev *mbd)
 
    	DEBUG(MTD_DEBUG_LEVEL1, "mtdblock_release\n");
 
+	mutex_lock(&mtdblks_lock);
+
 	mutex_lock(&mtdblk->cache_mutex);
 	write_cached_data(mtdblk);
 	mutex_unlock(&mtdblk->cache_mutex);
@@ -316,6 +325,9 @@ static int mtdblock_release(struct mtd_blktrans_dev *mbd)
 		vfree(mtdblk->cache_data);
 		kfree(mtdblk);
 	}
+
+	mutex_unlock(&mtdblks_lock);
+
 	DEBUG(MTD_DEBUG_LEVEL1, "ok\n");
 
 	return 0;
@@ -376,6 +388,8 @@ static struct mtd_blktrans_ops mtdblock_tr = {
 
 static int __init init_mtdblock(void)
 {
+	mutex_init(&mtdblks_lock);
+
 	return register_mtd_blktrans(&mtdblock_tr);
 }
 
-- 
GitLab


From 126b67b8d26f6623d199aa59279f2e3243f2144c Mon Sep 17 00:00:00 2001
From: Doug Thompson <dougthompson@xmission.com>
Date: Mon, 3 Aug 2009 12:37:06 +0200
Subject: [PATCH 0462/1153] amd64_edac: fix ECC checking

On the good path of BIOS enabled ECC and no override, the value returned
is 1 by omission and thus is deemed failing by the probe-function.

Allow proper module initialization by clearing the retval explicitly.

Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
---
 drivers/edac/amd64_edac.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/edac/amd64_edac.c b/drivers/edac/amd64_edac.c
index 24964c1d0af..5fa924d61b1 100644
--- a/drivers/edac/amd64_edac.c
+++ b/drivers/edac/amd64_edac.c
@@ -2977,6 +2977,9 @@ static int amd64_check_ecc_enabled(struct amd64_pvt *pvt)
 			"ECC is enabled by BIOS, Proceeding "
 			"with EDAC module initialization\n");
 
+		/* Signal good ECC status */
+		ret = 0;
+
 		/* CLEAR the override, since BIOS controlled it */
 		ecc_enable_override = 0;
 	}
-- 
GitLab


From 1c1a90d866c5fb029099b9f0f40534e01b7c4d91 Mon Sep 17 00:00:00 2001
From: Ralf Baechle <ralf@linux-mips.org>
Date: Sun, 5 Jul 2009 19:23:30 +0100
Subject: [PATCH 0463/1153] [PATCH] MIPS: Cavium: Move swapped comments to
 their rightful place.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/mm/c-octeon.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/mips/mm/c-octeon.c b/arch/mips/mm/c-octeon.c
index b165cdcb281..10ab69f7183 100644
--- a/arch/mips/mm/c-octeon.c
+++ b/arch/mips/mm/c-octeon.c
@@ -289,7 +289,7 @@ static void  cache_parity_error_octeon(int non_recoverable)
 }
 
 /**
- * Called when the the exception is not recoverable
+ * Called when the the exception is recoverable
  */
 
 asmlinkage void cache_parity_error_octeon_recoverable(void)
@@ -298,7 +298,7 @@ asmlinkage void cache_parity_error_octeon_recoverable(void)
 }
 
 /**
- * Called when the the exception is recoverable
+ * Called when the the exception is not recoverable
  */
 
 asmlinkage void cache_parity_error_octeon_non_recoverable(void)
-- 
GitLab


From 49316cbf0a9875f102f98dc8b7c80cfa142e33cf Mon Sep 17 00:00:00 2001
From: Ralf Baechle <ralf@linux-mips.org>
Date: Mon, 6 Jul 2009 09:13:17 +0100
Subject: [PATCH 0464/1153] MIPS: Eleminate filenames from comments

They tend to get not updated when files are moved around or copied and
lack any obvious use.  While at it zap some only too obvious comments and
as per Shinya's suggestion, add a copyright header to extable.c.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
---
 arch/mips/dec/ecc-berr.c                          | 2 --
 arch/mips/dec/int-handler.S                       | 2 --
 arch/mips/dec/ioasic-irq.c                        | 2 --
 arch/mips/dec/kn01-berr.c                         | 2 --
 arch/mips/dec/kn02-irq.c                          | 2 --
 arch/mips/dec/kn02xa-berr.c                       | 2 --
 arch/mips/dec/prom/call_o32.S                     | 2 --
 arch/mips/dec/prom/console.c                      | 2 --
 arch/mips/dec/time.c                              | 2 --
 arch/mips/emma/common/Makefile                    | 3 ---
 arch/mips/emma/common/prom.c                      | 3 ---
 arch/mips/emma/markeins/Makefile                  | 3 ---
 arch/mips/emma/markeins/irq.c                     | 3 ---
 arch/mips/emma/markeins/led.c                     | 3 ---
 arch/mips/emma/markeins/platform.c                | 3 ---
 arch/mips/emma/markeins/setup.c                   | 3 ---
 arch/mips/fw/lib/call_o32.S                       | 2 --
 arch/mips/include/asm/emma/emma2rh.h              | 3 ---
 arch/mips/include/asm/emma/markeins.h             | 3 ---
 arch/mips/kernel/irq_txx9.c                       | 2 --
 arch/mips/kernel/proc.c                           | 2 --
 arch/mips/kernel/stacktrace.c                     | 2 --
 arch/mips/mm/extable.c                            | 6 +++++-
 arch/mips/pci/fixup-emma2rh.c                     | 3 ---
 arch/mips/pci/fixup-sb1250.c                      | 2 --
 arch/mips/pci/ops-emma2rh.c                       | 3 ---
 arch/mips/pci/pci-emma2rh.c                       | 3 ---
 arch/mips/pci/pci-tx4927.c                        | 2 --
 arch/mips/pci/pci-tx4938.c                        | 2 --
 arch/mips/pci/pci-tx4939.c                        | 2 --
 arch/mips/pmc-sierra/msp71xx/gpio.c               | 2 --
 arch/mips/pmc-sierra/msp71xx/gpio_extended.c      | 2 --
 arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c | 2 --
 arch/mips/sibyte/swarm/swarm-i2c.c                | 2 --
 arch/mips/txx9/generic/mem_tx4927.c               | 2 --
 arch/mips/txx9/generic/setup.c                    | 2 --
 36 files changed, 5 insertions(+), 83 deletions(-)

diff --git a/arch/mips/dec/ecc-berr.c b/arch/mips/dec/ecc-berr.c
index 6a17c9b508e..7abce661b90 100644
--- a/arch/mips/dec/ecc-berr.c
+++ b/arch/mips/dec/ecc-berr.c
@@ -1,6 +1,4 @@
 /*
- *	linux/arch/mips/dec/ecc-berr.c
- *
  *	Bus error event handling code for systems equipped with ECC
  *	handling logic, i.e. DECstation/DECsystem 5000/200 (KN02),
  *	5000/240 (KN03), 5000/260 (KN05) and DECsystem 5900 (KN03),
diff --git a/arch/mips/dec/int-handler.S b/arch/mips/dec/int-handler.S
index 00cecdcc75f..82c85281878 100644
--- a/arch/mips/dec/int-handler.S
+++ b/arch/mips/dec/int-handler.S
@@ -1,6 +1,4 @@
 /*
- * arch/mips/dec/int-handler.S
- *
  * Copyright (C) 1995, 1996, 1997 Paul M. Antoine and Harald Koerfgen
  * Copyright (C) 2000, 2001, 2002, 2003, 2005  Maciej W. Rozycki
  *
diff --git a/arch/mips/dec/ioasic-irq.c b/arch/mips/dec/ioasic-irq.c
index 3acb133668d..cb41954fc32 100644
--- a/arch/mips/dec/ioasic-irq.c
+++ b/arch/mips/dec/ioasic-irq.c
@@ -1,6 +1,4 @@
 /*
- *	linux/arch/mips/dec/ioasic-irq.c
- *
  *	DEC I/O ASIC interrupts.
  *
  *	Copyright (c) 2002, 2003  Maciej W. Rozycki
diff --git a/arch/mips/dec/kn01-berr.c b/arch/mips/dec/kn01-berr.c
index d3b8002bf1e..b0dc6d53edd 100644
--- a/arch/mips/dec/kn01-berr.c
+++ b/arch/mips/dec/kn01-berr.c
@@ -1,6 +1,4 @@
 /*
- *	linux/arch/mips/dec/kn01-berr.c
- *
  *	Bus error event handling code for DECstation/DECsystem 3100
  *	and 2100 (KN01) systems equipped with parity error detection
  *	logic.
diff --git a/arch/mips/dec/kn02-irq.c b/arch/mips/dec/kn02-irq.c
index 02439dc0ba8..ed90a8deabc 100644
--- a/arch/mips/dec/kn02-irq.c
+++ b/arch/mips/dec/kn02-irq.c
@@ -1,6 +1,4 @@
 /*
- *	linux/arch/mips/dec/kn02-irq.c
- *
  *	DECstation 5000/200 (KN02) Control and Status Register
  *	interrupts.
  *
diff --git a/arch/mips/dec/kn02xa-berr.c b/arch/mips/dec/kn02xa-berr.c
index 5f04545c360..07ca5405d48 100644
--- a/arch/mips/dec/kn02xa-berr.c
+++ b/arch/mips/dec/kn02xa-berr.c
@@ -1,6 +1,4 @@
 /*
- *	linux/arch/mips/dec/kn02xa-berr.c
- *
  *	Bus error event handling code for 5000-series systems equipped
  *	with parity error detection logic, i.e. DECstation/DECsystem
  *	5000/120, /125, /133 (KN02-BA), 5000/150 (KN04-BA) and Personal
diff --git a/arch/mips/dec/prom/call_o32.S b/arch/mips/dec/prom/call_o32.S
index e523454bda3..8c8498159e4 100644
--- a/arch/mips/dec/prom/call_o32.S
+++ b/arch/mips/dec/prom/call_o32.S
@@ -1,6 +1,4 @@
 /*
- *	arch/mips/dec/prom/call_o32.S
- *
  *	O32 interface for the 64 (or N32) ABI.
  *
  *	Copyright (C) 2002  Maciej W. Rozycki
diff --git a/arch/mips/dec/prom/console.c b/arch/mips/dec/prom/console.c
index 078e1a12421..caa6e047caf 100644
--- a/arch/mips/dec/prom/console.c
+++ b/arch/mips/dec/prom/console.c
@@ -1,6 +1,4 @@
 /*
- *	arch/mips/dec/prom/console.c
- *
  *	DECstation PROM-based early console support.
  *
  *	Copyright (C) 2004, 2007  Maciej W. Rozycki
diff --git a/arch/mips/dec/time.c b/arch/mips/dec/time.c
index 1359c03ded5..463136e6685 100644
--- a/arch/mips/dec/time.c
+++ b/arch/mips/dec/time.c
@@ -1,6 +1,4 @@
 /*
- *  linux/arch/mips/dec/time.c
- *
  *  Copyright (C) 1991, 1992, 1995  Linus Torvalds
  *  Copyright (C) 2000, 2003  Maciej W. Rozycki
  *
diff --git a/arch/mips/emma/common/Makefile b/arch/mips/emma/common/Makefile
index c392d28c1ef..f27d84d1904 100644
--- a/arch/mips/emma/common/Makefile
+++ b/arch/mips/emma/common/Makefile
@@ -1,7 +1,4 @@
 #
-#  arch/mips/emma2rh/common/Makefile
-#       Makefile for the common code of NEC EMMA2RH based board.
-#
 #  Copyright (C) NEC Electronics Corporation 2005-2006
 #
 #  This program is free software; you can redistribute it and/or modify
diff --git a/arch/mips/emma/common/prom.c b/arch/mips/emma/common/prom.c
index 120f53fbdb4..708f0876140 100644
--- a/arch/mips/emma/common/prom.c
+++ b/arch/mips/emma/common/prom.c
@@ -1,7 +1,4 @@
 /*
- *  arch/mips/emma2rh/common/prom.c
- *      This file is prom file.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This file is based on the arch/mips/ddb5xxx/common/prom.c
diff --git a/arch/mips/emma/markeins/Makefile b/arch/mips/emma/markeins/Makefile
index 16e0017ba91..f8ba2508fa2 100644
--- a/arch/mips/emma/markeins/Makefile
+++ b/arch/mips/emma/markeins/Makefile
@@ -1,7 +1,4 @@
 #
-#  arch/mips/emma2rh/markeins/Makefile
-#       Makefile for the common code of NEC EMMA2RH based board.
-#
 #  Copyright (C) NEC Electronics Corporation 2005-2006
 #
 #  This program is free software; you can redistribute it and/or modify
diff --git a/arch/mips/emma/markeins/irq.c b/arch/mips/emma/markeins/irq.c
index 43828ae796e..9504b7ee0b7 100644
--- a/arch/mips/emma/markeins/irq.c
+++ b/arch/mips/emma/markeins/irq.c
@@ -1,7 +1,4 @@
 /*
- *  arch/mips/emma2rh/markeins/irq.c
- *      This file defines the irq handler for EMMA2RH.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This file is based on the arch/mips/ddb5xxx/ddb5477/irq.c
diff --git a/arch/mips/emma/markeins/led.c b/arch/mips/emma/markeins/led.c
index 377a181b656..49755896857 100644
--- a/arch/mips/emma/markeins/led.c
+++ b/arch/mips/emma/markeins/led.c
@@ -1,7 +1,4 @@
 /*
- *  arch/mips/emma2rh/markeins/led.c
- *      This file defines the led display for Mark-eins.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This program is free software; you can redistribute it and/or modify
diff --git a/arch/mips/emma/markeins/platform.c b/arch/mips/emma/markeins/platform.c
index 80ae12ef87d..b05b08b92a3 100644
--- a/arch/mips/emma/markeins/platform.c
+++ b/arch/mips/emma/markeins/platform.c
@@ -1,7 +1,4 @@
 /*
- *  arch/mips/emma2rh/markeins/platofrm.c
- *      This file sets up platform devices for EMMA2RH Mark-eins.
- *
  *  Copyright(C) MontaVista Software Inc, 2006
  *
  *  Author: dmitry pervushin <dpervushin@ru.mvista.com>
diff --git a/arch/mips/emma/markeins/setup.c b/arch/mips/emma/markeins/setup.c
index 67f45650008..335dc8c1a1b 100644
--- a/arch/mips/emma/markeins/setup.c
+++ b/arch/mips/emma/markeins/setup.c
@@ -1,7 +1,4 @@
 /*
- *  arch/mips/emma2rh/markeins/setup.c
- *      This file is setup for EMMA2RH Mark-eins.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This file is based on the arch/mips/ddb5xxx/ddb5477/setup.c.
diff --git a/arch/mips/fw/lib/call_o32.S b/arch/mips/fw/lib/call_o32.S
index bdf7d1d4081..e0a68713b3c 100644
--- a/arch/mips/fw/lib/call_o32.S
+++ b/arch/mips/fw/lib/call_o32.S
@@ -1,6 +1,4 @@
 /*
- *	arch/mips/dec/prom/call_o32.S
- *
  *	O32 interface for the 64 (or N32) ABI.
  *
  *	Copyright (C) 2002  Maciej W. Rozycki
diff --git a/arch/mips/include/asm/emma/emma2rh.h b/arch/mips/include/asm/emma/emma2rh.h
index 30aea91de62..2afb2fe11b3 100644
--- a/arch/mips/include/asm/emma/emma2rh.h
+++ b/arch/mips/include/asm/emma/emma2rh.h
@@ -1,7 +1,4 @@
 /*
- *  arch/mips/include/asm/emma/emma2rh.h
- *      This file is EMMA2RH common header.
- *
  *  Copyright (C) NEC Electronics Corporation 2005-2006
  *
  *  This file based on include/asm-mips/ddb5xxx/ddb5xxx.h
diff --git a/arch/mips/include/asm/emma/markeins.h b/arch/mips/include/asm/emma/markeins.h
index 973b0628490..2618bf23024 100644
--- a/arch/mips/include/asm/emma/markeins.h
+++ b/arch/mips/include/asm/emma/markeins.h
@@ -1,7 +1,4 @@
 /*
- *  include/asm-mips/emma2rh/markeins.h
- *      This file is EMMA2RH board depended header.
- *
  *  Copyright (C) NEC Electronics Corporation 2005-2006
  *
  *  This file based on include/asm-mips/ddb5xxx/ddb5xxx.h
diff --git a/arch/mips/kernel/irq_txx9.c b/arch/mips/kernel/irq_txx9.c
index a4d1462c27f..9b78029bea7 100644
--- a/arch/mips/kernel/irq_txx9.c
+++ b/arch/mips/kernel/irq_txx9.c
@@ -1,6 +1,4 @@
 /*
- * linux/arch/mips/kernel/irq_txx9.c
- *
  * Based on linux/arch/mips/jmr3927/rbhma3100/irq.c,
  *          linux/arch/mips/tx4927/common/tx4927_irq.c,
  *          linux/arch/mips/tx4938/common/irq.c
diff --git a/arch/mips/kernel/proc.c b/arch/mips/kernel/proc.c
index e0a4ac18fa0..26109c4d517 100644
--- a/arch/mips/kernel/proc.c
+++ b/arch/mips/kernel/proc.c
@@ -1,6 +1,4 @@
 /*
- *  linux/arch/mips/kernel/proc.c
- *
  *  Copyright (C) 1995, 1996, 2001  Ralf Baechle
  *  Copyright (C) 2001, 2004  MIPS Technologies, Inc.
  *  Copyright (C) 2004  Maciej W. Rozycki
diff --git a/arch/mips/kernel/stacktrace.c b/arch/mips/kernel/stacktrace.c
index 58f5cd76c8c..d52ff77baf3 100644
--- a/arch/mips/kernel/stacktrace.c
+++ b/arch/mips/kernel/stacktrace.c
@@ -1,6 +1,4 @@
 /*
- * arch/mips/kernel/stacktrace.c
- *
  * Stack trace management functions
  *
  *  Copyright (C) 2006 Atsushi Nemoto <anemo@mba.ocn.ne.jp>
diff --git a/arch/mips/mm/extable.c b/arch/mips/mm/extable.c
index 297fb9f390d..9d25d2ba4b9 100644
--- a/arch/mips/mm/extable.c
+++ b/arch/mips/mm/extable.c
@@ -1,5 +1,9 @@
 /*
- * linux/arch/mips/mm/extable.c
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997, 99, 2001 - 2004 Ralf Baechle <ralf@linux-mips.org>
  */
 #include <linux/module.h>
 #include <linux/spinlock.h>
diff --git a/arch/mips/pci/fixup-emma2rh.c b/arch/mips/pci/fixup-emma2rh.c
index fba5aad00d5..0d9ccf4dfc5 100644
--- a/arch/mips/pci/fixup-emma2rh.c
+++ b/arch/mips/pci/fixup-emma2rh.c
@@ -1,7 +1,4 @@
 /*
- *  arch/mips/pci/fixup-emma2rh.c
- *      This file defines the PCI configration.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This file is based on the arch/mips/ddb5xxx/ddb5477/pci.c
diff --git a/arch/mips/pci/fixup-sb1250.c b/arch/mips/pci/fixup-sb1250.c
index 0ad39e53f7b..f0bb9146e6c 100644
--- a/arch/mips/pci/fixup-sb1250.c
+++ b/arch/mips/pci/fixup-sb1250.c
@@ -1,6 +1,4 @@
 /*
- *	arch/mips/pci/fixup-sb1250.c
- *
  *	Copyright (C) 2004, 2006  MIPS Technologies, Inc.  All rights reserved.
  *	    Author:	Maciej W. Rozycki <macro@mips.com>
  *
diff --git a/arch/mips/pci/ops-emma2rh.c b/arch/mips/pci/ops-emma2rh.c
index 5947a70b0b7..710aef5c070 100644
--- a/arch/mips/pci/ops-emma2rh.c
+++ b/arch/mips/pci/ops-emma2rh.c
@@ -1,7 +1,4 @@
 /*
- *  arch/mips/pci/ops-emma2rh.c
- *      This file defines the PCI operation for EMMA2RH.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This file is based on the arch/mips/pci/ops-vr41xx.c
diff --git a/arch/mips/pci/pci-emma2rh.c b/arch/mips/pci/pci-emma2rh.c
index 2df4190232c..773e34ff4d1 100644
--- a/arch/mips/pci/pci-emma2rh.c
+++ b/arch/mips/pci/pci-emma2rh.c
@@ -1,7 +1,4 @@
 /*
- *  arch/mips/pci/pci-emma2rh.c
- *      This file defines the PCI configration.
- *
  *  Copyright (C) NEC Electronics Corporation 2004-2006
  *
  *  This file is based on the arch/mips/ddb5xxx/ddb5477/pci.c
diff --git a/arch/mips/pci/pci-tx4927.c b/arch/mips/pci/pci-tx4927.c
index aaa90059679..a5807406a7f 100644
--- a/arch/mips/pci/pci-tx4927.c
+++ b/arch/mips/pci/pci-tx4927.c
@@ -1,6 +1,4 @@
 /*
- * linux/arch/mips/pci/pci-tx4927.c
- *
  * Based on linux/arch/mips/txx9/rbtx4938/setup.c,
  *	    and RBTX49xx patch from CELF patch archive.
  *
diff --git a/arch/mips/pci/pci-tx4938.c b/arch/mips/pci/pci-tx4938.c
index 1ea257bc3b8..20e45f30b2e 100644
--- a/arch/mips/pci/pci-tx4938.c
+++ b/arch/mips/pci/pci-tx4938.c
@@ -1,6 +1,4 @@
 /*
- * linux/arch/mips/pci/pci-tx4938.c
- *
  * Based on linux/arch/mips/txx9/rbtx4938/setup.c,
  *	    and RBTX49xx patch from CELF patch archive.
  *
diff --git a/arch/mips/pci/pci-tx4939.c b/arch/mips/pci/pci-tx4939.c
index 5fecf1cdc32..9ef840693ba 100644
--- a/arch/mips/pci/pci-tx4939.c
+++ b/arch/mips/pci/pci-tx4939.c
@@ -1,6 +1,4 @@
 /*
- * linux/arch/mips/pci/pci-tx4939.c
- *
  * Based on linux/arch/mips/txx9/rbtx4939/setup.c,
  *	    and RBTX49xx patch from CELF patch archive.
  *
diff --git a/arch/mips/pmc-sierra/msp71xx/gpio.c b/arch/mips/pmc-sierra/msp71xx/gpio.c
index 69848c5813e..aaccbe52438 100644
--- a/arch/mips/pmc-sierra/msp71xx/gpio.c
+++ b/arch/mips/pmc-sierra/msp71xx/gpio.c
@@ -1,6 +1,4 @@
 /*
- * @file /arch/mips/pmc-sierra/msp71xx/gpio.c
- *
  * Generic PMC MSP71xx GPIO handling. These base gpio are controlled by two
  * types of registers. The data register sets the output level when in output
  * mode and when in input mode will contain the value at the input. The config
diff --git a/arch/mips/pmc-sierra/msp71xx/gpio_extended.c b/arch/mips/pmc-sierra/msp71xx/gpio_extended.c
index fc6dbc6cf1c..2a99f360fae 100644
--- a/arch/mips/pmc-sierra/msp71xx/gpio_extended.c
+++ b/arch/mips/pmc-sierra/msp71xx/gpio_extended.c
@@ -1,6 +1,4 @@
 /*
- * @file /arch/mips/pmc-sierra/msp71xx/gpio_extended.c
- *
  * Generic PMC MSP71xx EXTENDED (EXD) GPIO handling. The extended gpio is
  * a set of hardware registers that have no need for explicit locking as
  * it is handled by unique method of writing individual set/clr bits.
diff --git a/arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c b/arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c
index caf5e9a0acc..fc990cb3194 100644
--- a/arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c
+++ b/arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c
@@ -1,6 +1,4 @@
 /*
- *  arch/mips/pmc-sierra/yosemite/atmel_read_eeprom.c
- *
  *  Copyright (C) 2003 PMC-Sierra Inc.
  *  Author: Manish Lachwani (lachwani@pmc-sierra.com)
  *
diff --git a/arch/mips/sibyte/swarm/swarm-i2c.c b/arch/mips/sibyte/swarm/swarm-i2c.c
index 4282ac9d01d..062505054d4 100644
--- a/arch/mips/sibyte/swarm/swarm-i2c.c
+++ b/arch/mips/sibyte/swarm/swarm-i2c.c
@@ -1,6 +1,4 @@
 /*
- *	arch/mips/sibyte/swarm/swarm-i2c.c
- *
  *	Broadcom BCM91250A (SWARM), etc. I2C platform setup.
  *
  *	Copyright (c) 2008  Maciej W. Rozycki
diff --git a/arch/mips/txx9/generic/mem_tx4927.c b/arch/mips/txx9/generic/mem_tx4927.c
index ef6ea6e9787..70f9626f822 100644
--- a/arch/mips/txx9/generic/mem_tx4927.c
+++ b/arch/mips/txx9/generic/mem_tx4927.c
@@ -1,6 +1,4 @@
 /*
- * linux/arch/mips/txx9/generic/mem_tx4927.c
- *
  * common tx4927 memory interface
  *
  * Author: MontaVista Software, Inc.
diff --git a/arch/mips/txx9/generic/setup.c b/arch/mips/txx9/generic/setup.c
index 3b7d77d61ce..a205e2ba8e7 100644
--- a/arch/mips/txx9/generic/setup.c
+++ b/arch/mips/txx9/generic/setup.c
@@ -1,6 +1,4 @@
 /*
- * linux/arch/mips/txx9/generic/setup.c
- *
  * Based on linux/arch/mips/txx9/rbtx4938/setup.c,
  *	    and RBTX49xx patch from CELF patch archive.
  *
-- 
GitLab


From a887b4dada2f23b2ff2aa725e0509c92dc652597 Mon Sep 17 00:00:00 2001
From: Akinobu Mita <akinobu.mita@gmail.com>
Date: Sat, 4 Jul 2009 01:33:09 +0900
Subject: [PATCH 0465/1153] MIPS: Drop mmap_sem in pagefault oom path

Fix the pagefault oom path which does not drop mm->mmap_sem.
This was introduced by commit c7c1e3846bac1e4b8a8941f6a194812e28b0a519

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/mm/fault.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/mips/mm/fault.c b/arch/mips/mm/fault.c
index 6751ce9ede9..f956ecbb813 100644
--- a/arch/mips/mm/fault.c
+++ b/arch/mips/mm/fault.c
@@ -171,6 +171,7 @@ out_of_memory:
 	 * We ran out of memory, call the OOM killer, and return the userspace
 	 * (which will retry the fault, or kill us if we got oom-killed).
 	 */
+	up_read(&mm->mmap_sem);
 	pagefault_out_of_memory();
 	return;
 
-- 
GitLab


From 7d35cdc07dd26eb6667f66f8e2f43f833a926ecf Mon Sep 17 00:00:00 2001
From: Alexander Clouter <alex@digriz.org.uk>
Date: Sun, 5 Jul 2009 12:00:55 +0100
Subject: [PATCH 0466/1153] MIPS: Fix compile for !CONFIG_SMP

Commit fc03bc1715ca0ad4ccfe97aab16bcc9e7129c1a4 breaks compiling MIPS
with SMP disabled.  This patch fixes that.

Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/include/asm/gic.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/mips/include/asm/gic.h b/arch/mips/include/asm/gic.h
index 10292e37c1f..a8f57341f12 100644
--- a/arch/mips/include/asm/gic.h
+++ b/arch/mips/include/asm/gic.h
@@ -20,7 +20,7 @@
 #define GIC_TRIG_EDGE			1
 #define GIC_TRIG_LEVEL			0
 
-#if CONFIG_SMP
+#ifdef CONFIG_SMP
 #define GIC_NUM_INTRS			(24 + NR_CPUS * 2)
 #else
 #define GIC_NUM_INTRS			32
-- 
GitLab


From 78fe01a5a80da4621321a1dc199c3a0875e2fbb0 Mon Sep 17 00:00:00 2001
From: Yoichi Yuasa <yuasa@linux-mips.org>
Date: Wed, 8 Jul 2009 15:08:19 +0900
Subject: [PATCH 0467/1153] MIPS: MIPSsim: Fix unbalance brace in mipssim
 get_c0_compare_int()

cc1: warnings being treated as errors
arch/mips/mipssim/sim_time.c: In function 'get_c0_compare_int':
arch/mips/mipssim/sim_time.c:103: warning: ISO C90 forbids mixed declarations and code
arch/mips/mipssim/sim_time.c:116: error: expected declaration or statement at end of input
make[1]: *** [arch/mips/mipssim/sim_time.o] Error 1

Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/mipssim/sim_time.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/mips/mipssim/sim_time.c b/arch/mips/mipssim/sim_time.c
index 0cea932f124..5492c42f765 100644
--- a/arch/mips/mipssim/sim_time.c
+++ b/arch/mips/mipssim/sim_time.c
@@ -89,13 +89,13 @@ unsigned __cpuinit get_c0_compare_int(void)
 	if (cpu_has_veic) {
 		set_vi_handler(MSC01E_INT_CPUCTR, mips_timer_dispatch);
 		mips_cpu_timer_irq = MSC01E_INT_BASE + MSC01E_INT_CPUCTR;
-	} else {
-#endif
-	       {
-		if (cpu_has_vint)
-			set_vi_handler(cp0_compare_irq, mips_timer_dispatch);
-		mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq;
+
+		return mips_cpu_timer_irq;
 	}
+#endif
+	if (cpu_has_vint)
+		set_vi_handler(cp0_compare_irq, mips_timer_dispatch);
+	mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq;
 
 	return mips_cpu_timer_irq;
 }
-- 
GitLab


From 1de010a2702eb21d90883b83bf8c737d5e69d234 Mon Sep 17 00:00:00 2001
From: Huang Weiyi <weiyi.huang@gmail.com>
Date: Thu, 9 Jul 2009 06:14:37 +0800
Subject: [PATCH 0468/1153] MIPS: AR7: Remove unused inclusions of
 <linux/version.h>.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/ar7/platform.c | 1 -
 arch/mips/ar7/setup.c    | 1 -
 2 files changed, 2 deletions(-)

diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c
index 54224496178..c4d71fb18de 100644
--- a/arch/mips/ar7/platform.c
+++ b/arch/mips/ar7/platform.c
@@ -28,7 +28,6 @@
 #include <linux/serial_8250.h>
 #include <linux/ioport.h>
 #include <linux/io.h>
-#include <linux/version.h>
 #include <linux/vlynq.h>
 #include <linux/leds.h>
 #include <linux/string.h>
diff --git a/arch/mips/ar7/setup.c b/arch/mips/ar7/setup.c
index 6ebb5f16d96..39f6b5b9646 100644
--- a/arch/mips/ar7/setup.c
+++ b/arch/mips/ar7/setup.c
@@ -15,7 +15,6 @@
  *  with this program; if not, write to the Free Software Foundation, Inc.,
  *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
  */
-#include <linux/version.h>
 #include <linux/init.h>
 #include <linux/ioport.h>
 #include <linux/pm.h>
-- 
GitLab


From 484889fc85a223ef56edc31828b86751b2296b7c Mon Sep 17 00:00:00 2001
From: David Daney <ddaney@caviumnetworks.com>
Date: Wed, 8 Jul 2009 10:07:50 -0700
Subject: [PATCH 0469/1153] MIPS: Avoid clobbering struct pt_regs in kthreads

The resume() implementation octeon_switch.S examines the saved cp0_status
register.  We were clobbering the entire pt_regs structure in kernel
threads leading to random crashes.

When switching away from a kernel thread, the saved cp0_status is examined
and if bit 30 is set it is cleared and the CP2 state saved into the pt_regs
structure.  Since the kernel thread stack overlaid the pt_regs structure
this resulted in a corrupt stack.  When the kthread with the corrupt stack
was resumed, it could crash if it used any of the data in the stack that was
clobbered.

We fix it by moving the kernel thread stack down so it doesn't overlay
pt_regs.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/include/asm/processor.h | 5 +++--
 arch/mips/kernel/head.S           | 3 ++-
 arch/mips/kernel/process.c        | 4 +++-
 3 files changed, 8 insertions(+), 4 deletions(-)

diff --git a/arch/mips/include/asm/processor.h b/arch/mips/include/asm/processor.h
index 0f926aa0cb4..087a8884ef0 100644
--- a/arch/mips/include/asm/processor.h
+++ b/arch/mips/include/asm/processor.h
@@ -311,8 +311,9 @@ extern void start_thread(struct pt_regs * regs, unsigned long pc, unsigned long
 
 unsigned long get_wchan(struct task_struct *p);
 
-#define __KSTK_TOS(tsk) ((unsigned long)task_stack_page(tsk) + THREAD_SIZE - 32)
-#define task_pt_regs(tsk) ((struct pt_regs *)__KSTK_TOS(tsk) - 1)
+#define __KSTK_TOS(tsk) ((unsigned long)task_stack_page(tsk) + \
+			 THREAD_SIZE - 32 - sizeof(struct pt_regs))
+#define task_pt_regs(tsk) ((struct pt_regs *)__KSTK_TOS(tsk))
 #define KSTK_EIP(tsk) (task_pt_regs(tsk)->cp0_epc)
 #define KSTK_ESP(tsk) (task_pt_regs(tsk)->regs[29])
 #define KSTK_STATUS(tsk) (task_pt_regs(tsk)->cp0_status)
diff --git a/arch/mips/kernel/head.S b/arch/mips/kernel/head.S
index 492a0a8d70f..531ce7b1612 100644
--- a/arch/mips/kernel/head.S
+++ b/arch/mips/kernel/head.S
@@ -188,7 +188,8 @@ NESTED(kernel_entry, 16, sp)			# kernel entry point
 
 	MTC0		zero, CP0_CONTEXT	# clear context register
 	PTR_LA		$28, init_thread_union
-	PTR_LI		sp, _THREAD_SIZE - 32
+	/* Set the SP after an empty pt_regs.  */
+	PTR_LI		sp, _THREAD_SIZE - 32 - PT_SIZE
 	PTR_ADDU	sp, $28
 	set_saved_sp	sp, t0, t1
 	PTR_SUBU	sp, 4 * SZREG		# init stack pointer
diff --git a/arch/mips/kernel/process.c b/arch/mips/kernel/process.c
index c09d681b718..f3d73e1831c 100644
--- a/arch/mips/kernel/process.c
+++ b/arch/mips/kernel/process.c
@@ -115,7 +115,7 @@ int copy_thread(unsigned long clone_flags, unsigned long usp,
 {
 	struct thread_info *ti = task_thread_info(p);
 	struct pt_regs *childregs;
-	long childksp;
+	unsigned long childksp;
 	p->set_child_tid = p->clear_child_tid = NULL;
 
 	childksp = (unsigned long)task_stack_page(p) + THREAD_SIZE - 32;
@@ -132,6 +132,8 @@ int copy_thread(unsigned long clone_flags, unsigned long usp,
 
 	/* set up new TSS. */
 	childregs = (struct pt_regs *) childksp - 1;
+	/*  Put the stack after the struct pt_regs.  */
+	childksp = (unsigned long) childregs;
 	*childregs = *regs;
 	childregs->regs[7] = 0;	/* Clear error flag */
 
-- 
GitLab


From 008ee96f1204225503934cb57ac38c49f519c7ab Mon Sep 17 00:00:00 2001
From: Raghu Gandham <raghu@mips.com>
Date: Wed, 8 Jul 2009 17:00:44 -0700
Subject: [PATCH 0470/1153] [PATCH] MIPS: SMTC: Fix compile error

Commit fc03bc1715ca0ad4ccfe97aab16bcc9e7129c1a4 breaks when SMTC support
is enabled on Malta.

Signed-off-by: Raghu Gandham <raghu@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/mti-malta/malta-int.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/mips/mti-malta/malta-int.c b/arch/mips/mti-malta/malta-int.c
index a8756f82c31..3e0a9b35ba5 100644
--- a/arch/mips/mti-malta/malta-int.c
+++ b/arch/mips/mti-malta/malta-int.c
@@ -331,6 +331,7 @@ static struct irqaction irq_call = {
 	.flags		= IRQF_DISABLED|IRQF_PERCPU,
 	.name		= "IPI_call"
 };
+#endif /* CONFIG_MIPS_MT_SMP */
 
 static int gic_resched_int_base;
 static int gic_call_int_base;
@@ -346,7 +347,6 @@ unsigned int plat_ipi_resched_int_xlate(unsigned int cpu)
 {
 	return GIC_RESCHED_INT(cpu);
 }
-#endif /* CONFIG_MIPS_MT_SMP */
 
 static struct irqaction i8259irq = {
 	.handler = no_action,
-- 
GitLab


From d8e5f9fe5dab0e07985f2456cb6cc57788f53131 Mon Sep 17 00:00:00 2001
From: Kurt Martin <kurt@mips.com>
Date: Wed, 8 Jul 2009 19:22:35 -0700
Subject: [PATCH 0471/1153] MIPS: SMTC: Move cross VPE writes to after a TC is
 assigned to VPE.

Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Raghu Gandham <raghu@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/kernel/smtc.c | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)

diff --git a/arch/mips/kernel/smtc.c b/arch/mips/kernel/smtc.c
index 8a0626cbb10..c16bb6d6c25 100644
--- a/arch/mips/kernel/smtc.c
+++ b/arch/mips/kernel/smtc.c
@@ -465,11 +465,8 @@ void smtc_prepare_cpus(int cpus)
 	smtc_configure_tlb();
 
 	for (tc = 0, vpe = 0 ; (vpe < nvpe) && (tc < ntc) ; vpe++) {
-		/*
-		 * Set the MVP bits.
-		 */
-		settc(tc);
-		write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() | VPECONF0_MVP);
+		if (tcpervpe[vpe] == 0)
+			continue;
 		if (vpe != 0)
 			printk(", ");
 		printk("VPE %d: TC", vpe);
@@ -487,6 +484,12 @@ void smtc_prepare_cpus(int cpus)
 			tc++;
 		}
 		if (vpe != 0) {
+			/*
+			 * Allow this VPE to control others.
+			 */
+			write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() |
+					      VPECONF0_MVP);
+
 			/*
 			 * Clear any stale software interrupts from VPE's Cause
 			 */
-- 
GitLab


From 0e66fff883ef1b6e4c5031e8add8827cd0e2a195 Mon Sep 17 00:00:00 2001
From: Gabor Juhos <juhosg@openwrt.org>
Date: Mon, 13 Jul 2009 11:14:24 +0200
Subject: [PATCH 0472/1153] MIPS: Fix loading of modules with unresolved weak
 symbols

Loading of modules with unresolved weak symbols fails on MIPS
since '88173507e4fc1e7ecd111b0565e8cba0cb7dae6d'.

Modules: handle symbols that have a zero value

The module subsystem cannot handle symbols that are zero.  If symbols
are present that have a zero value then the module resolver prints out a
message that these symbols are unresolved.

We have to use IS_ERR_VALUE() to check that a symbol has been resolved
or not.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/kernel/module.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/mips/kernel/module.c b/arch/mips/kernel/module.c
index 3e9100dcc12..e465851a616 100644
--- a/arch/mips/kernel/module.c
+++ b/arch/mips/kernel/module.c
@@ -301,7 +301,7 @@ int apply_relocate(Elf_Shdr *sechdrs, const char *strtab,
 		/* This is the symbol it is referring to */
 		sym = (Elf_Sym *)sechdrs[symindex].sh_addr
 			+ ELF_MIPS_R_SYM(rel[i]);
-		if (!sym->st_value) {
+		if (IS_ERR_VALUE(sym->st_value)) {
 			/* Ignore unresolved weak symbol */
 			if (ELF_ST_BIND(sym->st_info) == STB_WEAK)
 				continue;
@@ -341,7 +341,7 @@ int apply_relocate_add(Elf_Shdr *sechdrs, const char *strtab,
 		/* This is the symbol it is referring to */
 		sym = (Elf_Sym *)sechdrs[symindex].sh_addr
 			+ ELF_MIPS_R_SYM(rel[i]);
-		if (!sym->st_value) {
+		if (IS_ERR_VALUE(sym->st_value)) {
 			/* Ignore unresolved weak symbol */
 			if (ELF_ST_BIND(sym->st_info) == STB_WEAK)
 				continue;
-- 
GitLab


From 4824f20c8b3adcbc5067c1bdd88408ee68da6bb2 Mon Sep 17 00:00:00 2001
From: Florian Fainelli <florian@openwrt.org>
Date: Mon, 27 Apr 2009 16:59:48 +0200
Subject: [PATCH 0473/1153] MIPS: MSP71xx: fix build failures on msp_irq_slp.c

Trying to build MSP4200 VoIP defconfig also fails on msp_irq_slp.c with a
non-existing reference to mask_slp_irq, which is in turn mask_msp_slp_irq.
Passed that, we will also miss a comma when calling
set_irq_chip_and_handler. This patch fixes both issues.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c b/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c
index f5f1b8d2bb9..66f6f8505e7 100644
--- a/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c
+++ b/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c
@@ -45,7 +45,7 @@ static inline void mask_msp_slp_irq(unsigned int irq)
  */
 static inline void ack_msp_slp_irq(unsigned int irq)
 {
-	mask_slp_irq(irq);
+	mask_msp_slp_irq(irq);
 
 	/*
 	 * only really necessary for 18, 16-14 and sometimes 3:0 (since
@@ -79,7 +79,7 @@ void __init msp_slp_irq_init(void)
 
 	/* initialize all the IRQ descriptors */
 	for (i = MSP_SLP_INTBASE; i < MSP_PER_INTBASE + 32; i++)
-		set_irq_chip_and_handler(i, &msp_slp_irq_controller
+		set_irq_chip_and_handler(i, &msp_slp_irq_controller,
 					 handle_level_irq);
 }
 
-- 
GitLab


From 6577890fd68c2671850214663dd9ae97feacbc47 Mon Sep 17 00:00:00 2001
From: Florian Fainelli <florian@openwrt.org>
Date: Mon, 27 Apr 2009 16:47:23 +0200
Subject: [PATCH 0474/1153] MIPS: MSPxxxx: define MIPS34K_MISSED_ITLB_WAR for
 other PMC-Sierra SoC

Trying to build a PMC-Sierra MSP4200 VoIP gateway defconfig will not work
since MIPS34K_MISSED_ITLB_WAR is not defined for all boards supported
within pmc-serria/msp71xx. This patch defines MIPS34K_MISSED_ITLB_WAR to
prevent such build failures:

  CHK     include/linux/version.h
  CHK     include/linux/utsrelease.h
  SYMLINK include/asm -> include/asm-mips
  CC      arch/mips/kernel/asm-offsets.s
In file included fromlinux-msp71xx/linux-2.6.29/arch/mips/include/asm/bitops.h:24,
                 from include/linux/bitops.h:17,
                 from include/linux/kernel.h:15,
                 from include/linux/sched.h:52,
                 from arch/mips/kernel/asm-offsets.c:13:
linux-msp71xx/linux-2.6.29/arch/mips/include/asm/war.h:241:2: error: #error Check setting of MIPS34K_MISSED_ITLB_WAR for your
platform

This fixes a compile error when building for the MSP4200 boards.  Identical
patches to fix this were send by

  Florian Fainelli <florian@openwrt.org>
  Shane McDonald <mcdonald.shane@gmail.com>

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/include/asm/pmc-sierra/msp71xx/war.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/mips/include/asm/pmc-sierra/msp71xx/war.h b/arch/mips/include/asm/pmc-sierra/msp71xx/war.h
index 0bf48fc1892..9e2ee429c52 100644
--- a/arch/mips/include/asm/pmc-sierra/msp71xx/war.h
+++ b/arch/mips/include/asm/pmc-sierra/msp71xx/war.h
@@ -23,6 +23,8 @@
 #if defined(CONFIG_PMC_MSP7120_EVAL) || defined(CONFIG_PMC_MSP7120_GW) || \
 	defined(CONFIG_PMC_MSP7120_FPGA)
 #define MIPS34K_MISSED_ITLB_WAR         1
+#else
+#define MIPS34K_MISSED_ITLB_WAR         0
 #endif
 
 #endif /* __ASM_MIPS_PMC_SIERRA_WAR_H */
-- 
GitLab


From 0ca71737fee65521ede964afbd2d5484976ed0ed Mon Sep 17 00:00:00 2001
From: Shane McDonald <mcdonald.shane@gmail.com>
Date: Sun, 12 Jul 2009 10:42:06 -0600
Subject: [PATCH 0475/1153] MIPS: Simplify and correct interrupt handling for
 MSP4200

The current interrupt handling code for the MSP4200 always masks an
interrupt before acknowledging it.  This is not required, as that will be
handled by the level interrupt handler.  This change simplifies the MSP4200
code to remove the masking in the ack routine, and makes sure that the
minimum required operation is performed for masking and acking, rather
than always both masking and acking the interrupt.

Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c | 10 +---------
 1 file changed, 1 insertion(+), 9 deletions(-)

diff --git a/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c b/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c
index 66f6f8505e7..61f39023234 100644
--- a/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c
+++ b/arch/mips/pmc-sierra/msp71xx/msp_irq_slp.c
@@ -45,13 +45,6 @@ static inline void mask_msp_slp_irq(unsigned int irq)
  */
 static inline void ack_msp_slp_irq(unsigned int irq)
 {
-	mask_msp_slp_irq(irq);
-
-	/*
-	 * only really necessary for 18, 16-14 and sometimes 3:0 (since
-	 * these can be edge sensitive) but it doesn't hurt  for the others.
-	 */
-
 	/* check for PER interrupt range */
 	if (irq < MSP_PER_INTBASE)
 		*SLP_INT_STS_REG = (1 << (irq - MSP_SLP_INTBASE));
@@ -62,8 +55,7 @@ static inline void ack_msp_slp_irq(unsigned int irq)
 static struct irq_chip msp_slp_irq_controller = {
 	.name = "MSP_SLP",
 	.ack = ack_msp_slp_irq,
-	.mask = ack_msp_slp_irq,
-	.mask_ack = ack_msp_slp_irq,
+	.mask = mask_msp_slp_irq,
 	.unmask = unmask_msp_slp_irq,
 };
 
-- 
GitLab


From 3e6e92183118d26d856e8efb549987164d1b49b4 Mon Sep 17 00:00:00 2001
From: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Date: Wed, 15 Jul 2009 22:03:56 +0900
Subject: [PATCH 0476/1153] MIPS: RBTX4939: Fix IOC pin-enable register
 updating

The rbtx4939_update_ioc_pen() expects txx9_ce_res[] already initialized.
Call it after tx4939_setup().

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/txx9/rbtx4939/setup.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/mips/txx9/rbtx4939/setup.c b/arch/mips/txx9/rbtx4939/setup.c
index c033ffe71cd..b0c241ecf60 100644
--- a/arch/mips/txx9/rbtx4939/setup.c
+++ b/arch/mips/txx9/rbtx4939/setup.c
@@ -512,10 +512,10 @@ static void __init rbtx4939_setup(void)
 	rbtx4939_ebusc_setup();
 	/* always enable ATA0 */
 	txx9_set64(&tx4939_ccfgptr->pcfg, TX4939_PCFG_ATA0MODE);
-	rbtx4939_update_ioc_pen();
 	if (txx9_master_clock == 0)
 		txx9_master_clock = 20000000;
 	tx4939_setup();
+	rbtx4939_update_ioc_pen();
 #ifdef HAVE_RBTX4939_IOSWAB
 	ioswabw = rbtx4939_ioswabw;
 	__mem_ioswabw = rbtx4939_mem_ioswabw;
-- 
GitLab


From 838c05705ef8c110037a713526bb18762db0a241 Mon Sep 17 00:00:00 2001
From: David Daney <ddaney@caviumnetworks.com>
Date: Tue, 14 Jul 2009 18:16:50 -0700
Subject: [PATCH 0477/1153] MIPS: Octeon PCIe: Make hardware and software bus
 numbers match.

Some SiliconImage PCIe SATA controlers are not detected when the bus
numbers differ.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/pci/pcie-octeon.c | 31 +++++++++++++++++--------------
 1 file changed, 17 insertions(+), 14 deletions(-)

diff --git a/arch/mips/pci/pcie-octeon.c b/arch/mips/pci/pcie-octeon.c
index 75262247f3e..6aa5c542d52 100644
--- a/arch/mips/pci/pcie-octeon.c
+++ b/arch/mips/pci/pcie-octeon.c
@@ -1040,19 +1040,29 @@ static inline int octeon_pcie_read_config(int pcie_port, struct pci_bus *bus,
 	int bus_number = bus->number;
 
 	/*
-	 * We need to force the bus number to be zero on the root
-	 * bus. Linux numbers the 2nd root bus to start after all
-	 * buses on root 0.
+	 * For the top level bus make sure our hardware bus number
+	 * matches the software one.
 	 */
-	if (bus->parent == NULL)
-		bus_number = 0;
+	if (bus->parent == NULL) {
+		union cvmx_pciercx_cfg006 pciercx_cfg006;
+		pciercx_cfg006.u32 = cvmx_pcie_cfgx_read(pcie_port,
+			CVMX_PCIERCX_CFG006(pcie_port));
+		if (pciercx_cfg006.s.pbnum != bus_number) {
+			pciercx_cfg006.s.pbnum = bus_number;
+			pciercx_cfg006.s.sbnum = bus_number;
+			pciercx_cfg006.s.subbnum = bus_number;
+			cvmx_pcie_cfgx_write(pcie_port,
+				CVMX_PCIERCX_CFG006(pcie_port),
+				pciercx_cfg006.u32);
+		}
+	}
 
 	/*
 	 * PCIe only has a single device connected to Octeon. It is
 	 * always device ID 0. Don't bother doing reads for other
 	 * device IDs on the first segment.
 	 */
-	if ((bus_number == 0) && (devfn >> 3 != 0))
+	if ((bus->parent == NULL) && (devfn >> 3 != 0))
 		return PCIBIOS_FUNC_NOT_SUPPORTED;
 
 	/*
@@ -1070,7 +1080,7 @@ static inline int octeon_pcie_read_config(int pcie_port, struct pci_bus *bus,
 		 * bridge only respondes to device ID 0, function
 		 * 0-1
 		 */
-		if ((bus_number == 0) && (devfn >= 2))
+		if ((bus->parent == NULL) && (devfn >= 2))
 			return PCIBIOS_FUNC_NOT_SUPPORTED;
 		/*
 		 * The PCI-X slots are device ID 2,3. Choose one of
@@ -1167,13 +1177,6 @@ static inline int octeon_pcie_write_config(int pcie_port, struct pci_bus *bus,
 					   int size, u32 val)
 {
 	int bus_number = bus->number;
-	/*
-	 * We need to force the bus number to be zero on the root
-	 * bus. Linux numbers the 2nd root bus to start after all
-	 * busses on root 0.
-	 */
-	if (bus->parent == NULL)
-		bus_number = 0;
 
 	switch (size) {
 	case 4:
-- 
GitLab


From dd34b5a82feadfaee4f8dea83a694d9349f94a28 Mon Sep 17 00:00:00 2001
From: Florian Fainelli <florian@openwrt.org>
Date: Tue, 21 Jul 2009 12:38:10 +0200
Subject: [PATCH 0478/1153] MIPS: AR7: Fix build warning on memory.c

This patch fixes the following build warning:
arch/mips/ar7/memory.c: In function 'memsize':
arch/mips/ar7/memory.c:55: warning: passing argument 1 of 'writel' makes integer from pointer without a cast

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/ar7/memory.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/mips/ar7/memory.c b/arch/mips/ar7/memory.c
index 46fed44825a..696c723dc6d 100644
--- a/arch/mips/ar7/memory.c
+++ b/arch/mips/ar7/memory.c
@@ -52,7 +52,7 @@ static int __init memsize(void)
 		size <<= 1;
 	} while (size < (64 << 20));
 
-	writel(tmpaddr, &addr);
+	writel((u32)tmpaddr, &addr);
 
 	return size;
 }
-- 
GitLab


From ea85a0e4cc870d2bb92e3b2007007901209bb7de Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Wed, 29 Jul 2009 22:02:53 +0200
Subject: [PATCH 0479/1153] MIPS: Fix read buffer overflow

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/ar7/prom.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/mips/ar7/prom.c b/arch/mips/ar7/prom.c
index a320bceb2f9..5ad6f1db656 100644
--- a/arch/mips/ar7/prom.c
+++ b/arch/mips/ar7/prom.c
@@ -144,7 +144,7 @@ static char * __init lookup_psp_var_map(u8 num)
 {
 	int i;
 
-	for (i = 0; i < sizeof(psp_var_map); i++)
+	for (i = 0; i < ARRAY_SIZE(psp_var_map); i++)
 		if (psp_var_map[i].num == num)
 			return psp_var_map[i].value;
 
-- 
GitLab


From 50ca961912be315035cb0f3508e35c974851da2a Mon Sep 17 00:00:00 2001
From: Florian Fainelli <florian@openwrt.org>
Date: Fri, 24 Jul 2009 13:24:15 +0200
Subject: [PATCH 0480/1153] MIPS: AR7: Fix build failures when
 CONFIG_SERIAL_8250 is not enabled

This patch fixes the following build failure when CONFIG_SERIAL_8250
is not enabled in the kernel configuration:
arch/mips/ar7/built-in.o: In function 'ar7_register_devices':
platform.c:(.init.text+0x61c): undefined reference to 'early_serial_setup'
platform.c:(.init.text+0x61c): relocation truncated to fit: R_MIPS_26 against 'early_serial_setup'
platform.c:(.init.text+0x68c): undefined reference to 'early_serial_setup'
platform.c:(.init.text+0x68c): relocation truncated to fit: R_MIPS_26 against 'early_serial_setup'

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/ar7/platform.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c
index c4d71fb18de..8ef8266e47f 100644
--- a/arch/mips/ar7/platform.c
+++ b/arch/mips/ar7/platform.c
@@ -480,6 +480,7 @@ static void __init detect_leds(void)
 static int __init ar7_register_devices(void)
 {
 	int res;
+#ifdef CONFIG_SERIAL_8250
 	static struct uart_port uart_port[2];
 
 	memset(uart_port, 0, sizeof(struct uart_port) * 2);
@@ -511,7 +512,7 @@ static int __init ar7_register_devices(void)
 		if (res)
 			return res;
 	}
-
+#endif /* CONFIG_SERIAL_8250 */
 	res = platform_device_register(&physmap_flash);
 	if (res)
 		return res;
-- 
GitLab


From 8e84c1480d2e7d98d487b567100717b9cc9dcfd7 Mon Sep 17 00:00:00 2001
From: Florian Fainelli <florian@openwrt.org>
Date: Fri, 24 Jul 2009 13:18:16 +0200
Subject: [PATCH 0481/1153] MIPS: AR7: Use DMA_BIT_MASK(nn) instead of
 deprecated DMA_nnBIT_MASK

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/ar7/platform.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c
index 8ef8266e47f..2ecab615593 100644
--- a/arch/mips/ar7/platform.c
+++ b/arch/mips/ar7/platform.c
@@ -242,13 +242,13 @@ static struct platform_device physmap_flash = {
 	.num_resources = 1,
 };
 
-static u64 cpmac_dma_mask = DMA_32BIT_MASK;
+static u64 cpmac_dma_mask = DMA_BIT_MASK(32);
 static struct platform_device cpmac_low = {
 	.id = 0,
 	.name = "cpmac",
 	.dev = {
 		.dma_mask = &cpmac_dma_mask,
-		.coherent_dma_mask = DMA_32BIT_MASK,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
 		.platform_data = &cpmac_low_data,
 	},
 	.resource = cpmac_low_res,
@@ -260,7 +260,7 @@ static struct platform_device cpmac_high = {
 	.name = "cpmac",
 	.dev = {
 		.dma_mask = &cpmac_dma_mask,
-		.coherent_dma_mask = DMA_32BIT_MASK,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
 		.platform_data = &cpmac_high_data,
 	},
 	.resource = cpmac_high_res,
-- 
GitLab


From e5b3837a52c7fe5c7086590bed902f0fac5f9ec0 Mon Sep 17 00:00:00 2001
From: Florian Fainelli <florian@openwrt.org>
Date: Fri, 24 Jul 2009 13:18:42 +0200
Subject: [PATCH 0482/1153] MIPS: AR7: Remove unused tnetd7200_get_clock
 function

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/ar7/clock.c | 13 -------------
 1 file changed, 13 deletions(-)

diff --git a/arch/mips/ar7/clock.c b/arch/mips/ar7/clock.c
index 27dc6663f2f..cc65c8eb391 100644
--- a/arch/mips/ar7/clock.c
+++ b/arch/mips/ar7/clock.c
@@ -264,19 +264,6 @@ static void __init tnetd7300_init_clocks(void)
 	iounmap(bootcr);
 }
 
-static int tnetd7200_get_clock(int base, struct tnetd7200_clock *clock,
-	u32 *bootcr, u32 bus_clock)
-{
-	int divisor = ((readl(&clock->prediv) & 0x1f) + 1) *
-		((readl(&clock->postdiv) & 0x1f) + 1);
-
-	if (*bootcr & BOOT_PLL_BYPASS)
-		return base / divisor;
-
-	return base * ((readl(&clock->mul) & 0xf) + 1) / divisor;
-}
-
-
 static void tnetd7200_set_clock(int base, struct tnetd7200_clock *clock,
 	int prediv, int postdiv, int postdiv2, int mul, u32 frequency)
 {
-- 
GitLab


From 619e22632ea3110323b1851a7fecb52bf8505fd2 Mon Sep 17 00:00:00 2001
From: Florian Fainelli <florian@openwrt.org>
Date: Fri, 24 Jul 2009 13:19:10 +0200
Subject: [PATCH 0483/1153] MIPS: AR7: Override CFLAGS with -Werror

Now that we have removed all warnings from the ar7 board code we can use
-Werror like on other MIPS boards.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/ar7/Makefile | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/mips/ar7/Makefile b/arch/mips/ar7/Makefile
index 7435e44b396..26bc5da1899 100644
--- a/arch/mips/ar7/Makefile
+++ b/arch/mips/ar7/Makefile
@@ -8,3 +8,4 @@ obj-y := \
 	platform.o \
 	gpio.o \
 	clock.o
+EXTRA_CFLAGS += -Werror
-- 
GitLab


From a1b021d3992d9be03b0abec1a7ed78e713b94206 Mon Sep 17 00:00:00 2001
From: Florian Fainelli <florian@openwrt.org>
Date: Sat, 1 Aug 2009 23:51:20 +0200
Subject: [PATCH 0484/1153] MIPS: MTX-1: Request button GPIO before setting its
 direction

This patch fixes the following warning at boot time:
WARNING: at drivers/gpio/gpiolib.c:83 0x8021d5e0()
autorequest GPIO-207
Modules linked in:
Call Trace:[<8011e0ec>] 0x8011e0ec
[<80110a28>] 0x80110a28
[<80110a28>] 0x80110a28
[..snip..]

The current code does not request the GPIO and attempts
to set its direction, which is a violation of the GPIO API.
This patch also unhardcode the GPIO we request and use
the one we defined in the button driver.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/alchemy/mtx-1/platform.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)

diff --git a/arch/mips/alchemy/mtx-1/platform.c b/arch/mips/alchemy/mtx-1/platform.c
index 8b5914d1241..e30e42add69 100644
--- a/arch/mips/alchemy/mtx-1/platform.c
+++ b/arch/mips/alchemy/mtx-1/platform.c
@@ -1,7 +1,7 @@
 /*
  * MTX-1 platform devices registration
  *
- * Copyright (C) 2007, Florian Fainelli <florian@openwrt.org>
+ * Copyright (C) 2007-2009, Florian Fainelli <florian@openwrt.org>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -142,7 +142,17 @@ static struct __initdata platform_device * mtx1_devs[] = {
 
 static int __init mtx1_register_devices(void)
 {
-	gpio_direction_input(207);
+	int rc;
+
+	rc = gpio_request(mtx1_gpio_button[0].gpio,
+					mtx1_gpio_button[0].desc);
+	if (rc < 0) {
+		printk(KERN_INFO "mtx1: failed to request %d\n",
+					mtx1_gpio_button[0].gpio);
+		goto out;
+	}
+	gpio_direction_input(mtx1_gpio_button[0].gpio);
+out:
 	return platform_add_devices(mtx1_devs, ARRAY_SIZE(mtx1_devs));
 }
 
-- 
GitLab


From 64f1815507f207ec54ee6b9ae69c48bd153e83b4 Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Sun, 2 Aug 2009 10:48:08 +0200
Subject: [PATCH 0485/1153] MIPS: Use DIV_ROUND_CLOSEST

The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
expression x,__divisor;
@@

- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/nxp/pnx8550/common/time.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/mips/nxp/pnx8550/common/time.c b/arch/mips/nxp/pnx8550/common/time.c
index 8df43e9e4d9..18b19278487 100644
--- a/arch/mips/nxp/pnx8550/common/time.c
+++ b/arch/mips/nxp/pnx8550/common/time.c
@@ -138,7 +138,7 @@ __init void plat_time_init(void)
 	 * HZ timer interrupts per second.
 	 */
 	mips_hpt_frequency = 27UL * ((1000000UL * n)/(m * pow2p));
-	cpj = (mips_hpt_frequency + HZ / 2) / HZ;
+	cpj = DIV_ROUND_CLOSEST(mips_hpt_frequency, HZ);
 	write_c0_count(0);
 	timer_ack();
 
-- 
GitLab


From 3d4656d68bad84604f5b01f93e066cd02f77154b Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Fri, 31 Jul 2009 14:52:51 +0200
Subject: [PATCH 0486/1153] MIPS: Jazz: Fix read buffer overflow

Check whether index is within bounds before testing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/jazz/jazzdma.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/mips/jazz/jazzdma.c b/arch/mips/jazz/jazzdma.c
index f0fd636723b..0d64d0f4641 100644
--- a/arch/mips/jazz/jazzdma.c
+++ b/arch/mips/jazz/jazzdma.c
@@ -190,7 +190,7 @@ int vdma_free(unsigned long laddr)
 		return -1;
 	}
 
-	while (pgtbl[i].owner == laddr && i < VDMA_PGTBL_ENTRIES) {
+	while (i < VDMA_PGTBL_ENTRIES && pgtbl[i].owner == laddr) {
 		pgtbl[i].owner = VDMA_PAGE_EMPTY;
 		i++;
 	}
-- 
GitLab


From 39b3d44624e9c54e7406274beaf569fe33af2b96 Mon Sep 17 00:00:00 2001
From: David Daney <ddaney@caviumnetworks.com>
Date: Fri, 31 Jul 2009 14:30:07 -0700
Subject: [PATCH 0487/1153] MIPS: Octeon: Run IPI code with interrupts
 disabled.

In mm/slab.c the function do_ccupdate_local requires that interrupts be
disabled.  If they are not, we panic with CONFIG_DEBUG_SLAB.

So we disable interrupts while processing IPIs.  Also these are not shared
irqs, so get rid of the IRQF_SHARED flag.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/cavium-octeon/smp.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/mips/cavium-octeon/smp.c b/arch/mips/cavium-octeon/smp.c
index 0b891a9c625..32d51a31dc4 100644
--- a/arch/mips/cavium-octeon/smp.c
+++ b/arch/mips/cavium-octeon/smp.c
@@ -194,11 +194,11 @@ static void octeon_init_secondary(void)
 void octeon_prepare_cpus(unsigned int max_cpus)
 {
 	cvmx_write_csr(CVMX_CIU_MBOX_CLRX(cvmx_get_core_num()), 0xffffffff);
-	if (request_irq(OCTEON_IRQ_MBOX0, mailbox_interrupt, IRQF_SHARED,
+	if (request_irq(OCTEON_IRQ_MBOX0, mailbox_interrupt, IRQF_DISABLED,
 			"mailbox0", mailbox_interrupt)) {
 		panic("Cannot request_irq(OCTEON_IRQ_MBOX0)\n");
 	}
-	if (request_irq(OCTEON_IRQ_MBOX1, mailbox_interrupt, IRQF_SHARED,
+	if (request_irq(OCTEON_IRQ_MBOX1, mailbox_interrupt, IRQF_DISABLED,
 			"mailbox1", mailbox_interrupt)) {
 		panic("Cannot request_irq(OCTEON_IRQ_MBOX1)\n");
 	}
-- 
GitLab


From 6f9fdeb6761a46ded6bf4b799993a3f235ab853d Mon Sep 17 00:00:00 2001
From: Ralf Baechle <ralf@linux-mips.org>
Date: Mon, 3 Aug 2009 10:50:19 +0100
Subject: [PATCH 0488/1153] MIPS: Module: Make error messages unique.

There were three different errors resulting in a "dangerous relocation"
message.  Add the relocation type to the messgages to make them more
useful.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/kernel/module.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/arch/mips/kernel/module.c b/arch/mips/kernel/module.c
index e465851a616..6f51dda87fc 100644
--- a/arch/mips/kernel/module.c
+++ b/arch/mips/kernel/module.c
@@ -98,7 +98,8 @@ static int apply_r_mips_32_rela(struct module *me, u32 *location, Elf_Addr v)
 static int apply_r_mips_26_rel(struct module *me, u32 *location, Elf_Addr v)
 {
 	if (v % 4) {
-		printk(KERN_ERR "module %s: dangerous relocation\n", me->name);
+		pr_err("module %s: dangerous R_MIPS_26 REL relocation\n",
+		       me->name);
 		return -ENOEXEC;
 	}
 
@@ -118,7 +119,8 @@ static int apply_r_mips_26_rel(struct module *me, u32 *location, Elf_Addr v)
 static int apply_r_mips_26_rela(struct module *me, u32 *location, Elf_Addr v)
 {
 	if (v % 4) {
-		printk(KERN_ERR "module %s: dangerous relocation\n", me->name);
+		pr_err("module %s: dangerous R_MIPS_26 RELArelocation\n",
+		       me->name);
 		return -ENOEXEC;
 	}
 
@@ -222,7 +224,7 @@ static int apply_r_mips_lo16_rel(struct module *me, u32 *location, Elf_Addr v)
 	return 0;
 
 out_danger:
-	printk(KERN_ERR "module %s: dangerous " "relocation\n", me->name);
+	pr_err("module %s: dangerous R_MIPS_LO16 REL relocation\n", me->name);
 
 	return -ENOEXEC;
 }
-- 
GitLab


From e2a9cf96a0af24f33206b4bb98cc3a12242260c1 Mon Sep 17 00:00:00 2001
From: Raghu Gandham <raghu@mips.com>
Date: Fri, 10 Jul 2009 02:01:32 -0700
Subject: [PATCH 0489/1153] MIPS: VPE: Fix compiler warning.

Signed-off-by: Raghu Gandham <raghu@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/kernel/vpe.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c
index 07b9ec2c6e3..3d4ef841d82 100644
--- a/arch/mips/kernel/vpe.c
+++ b/arch/mips/kernel/vpe.c
@@ -327,7 +327,8 @@ static void layout_sections(struct module *mod, const Elf_Ehdr * hdr,
 			    || (s->sh_flags & masks[m][1])
 			    || s->sh_entsize != ~0UL)
 				continue;
-			s->sh_entsize = get_offset(&mod->core_size, s);
+			s->sh_entsize =
+				get_offset((unsigned long *)&mod->core_size, s);
 		}
 
 		if (m == 0)
-- 
GitLab


From 477c4b07406357ad93d0e32788dbf3ee814eadaa Mon Sep 17 00:00:00 2001
From: Ralf Baechle <ralf@linux-mips.org>
Date: Mon, 3 Aug 2009 12:26:40 +0100
Subject: [PATCH 0490/1153] MIPS: VPE: Free relocation chain on error.

This may happen if a bad sequence of relocations is being encountered.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/kernel/vpe.c | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c
index 3d4ef841d82..245b03e8808 100644
--- a/arch/mips/kernel/vpe.c
+++ b/arch/mips/kernel/vpe.c
@@ -462,16 +462,15 @@ static int apply_r_mips_lo16(struct module *me, uint32_t *location,
 {
 	unsigned long insnlo = *location;
 	Elf32_Addr val, vallo;
+	struct mips_hi16 *l, *next;
 
 	/* Sign extend the addend we extract from the lo insn.  */
 	vallo = ((insnlo & 0xffff) ^ 0x8000) - 0x8000;
 
 	if (mips_hi16_list != NULL) {
-		struct mips_hi16 *l;
 
 		l = mips_hi16_list;
 		while (l != NULL) {
-			struct mips_hi16 *next;
 			unsigned long insn;
 
 			/*
@@ -481,7 +480,7 @@ static int apply_r_mips_lo16(struct module *me, uint32_t *location,
 				printk(KERN_DEBUG "VPE loader: "
 				       "apply_r_mips_lo16/hi16: \t"
 				       "inconsistent value information\n");
-				return -ENOEXEC;
+				goto out_free;
 			}
 
 			/*
@@ -519,6 +518,16 @@ static int apply_r_mips_lo16(struct module *me, uint32_t *location,
 	*location = insnlo;
 
 	return 0;
+
+out_free:
+	while (l != NULL) {
+		next = l->next;
+		kfree(l);
+		l = next;
+	}
+	mips_hi16_list = NULL;
+
+	return -ENOEXEC;
 }
 
 static int (*reloc_handlers[]) (struct module *me, uint32_t *location,
-- 
GitLab


From f18b51cc1f97ca290256e8f94127f6856a42d605 Mon Sep 17 00:00:00 2001
From: Ralf Baechle <ralf@linux-mips.org>
Date: Mon, 3 Aug 2009 12:54:35 +0100
Subject: [PATCH 0491/1153] MIPS: VPE: Make various functions static.

None of these is used outside the VPE loader.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/kernel/vpe.c | 17 ++++++++---------
 1 file changed, 8 insertions(+), 9 deletions(-)

diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c
index 245b03e8808..6cbeb2a5452 100644
--- a/arch/mips/kernel/vpe.c
+++ b/arch/mips/kernel/vpe.c
@@ -155,10 +155,9 @@ struct {
 };
 
 static void release_progmem(void *ptr);
-extern void save_gp_address(unsigned int secbase, unsigned int rel);
 
 /* get the vpe associated with this minor */
-struct vpe *get_vpe(int minor)
+static struct vpe *get_vpe(int minor)
 {
 	struct vpe *v;
 
@@ -174,7 +173,7 @@ struct vpe *get_vpe(int minor)
 }
 
 /* get the vpe associated with this minor */
-struct tc *get_tc(int index)
+static struct tc *get_tc(int index)
 {
 	struct tc *t;
 
@@ -199,7 +198,7 @@ struct tc *get_tc_unused(void)
 }
 
 /* allocate a vpe and associate it with this minor (or index) */
-struct vpe *alloc_vpe(int minor)
+static struct vpe *alloc_vpe(int minor)
 {
 	struct vpe *v;
 
@@ -216,7 +215,7 @@ struct vpe *alloc_vpe(int minor)
 }
 
 /* allocate a tc. At startup only tc0 is running, all other can be halted. */
-struct tc *alloc_tc(int index)
+static struct tc *alloc_tc(int index)
 {
 	struct tc *tc;
 
@@ -232,7 +231,7 @@ out:
 }
 
 /* clean up and free everything */
-void release_vpe(struct vpe *v)
+static void release_vpe(struct vpe *v)
 {
 	list_del(&v->list);
 	if (v->load_addr)
@@ -240,7 +239,7 @@ void release_vpe(struct vpe *v)
 	kfree(v);
 }
 
-void dump_mtregs(void)
+static void dump_mtregs(void)
 {
 	unsigned long val;
 
@@ -551,7 +550,7 @@ static char *rstrs[] = {
 	[R_MIPS_PC16] = "MIPS_PC16"
 };
 
-int apply_relocations(Elf32_Shdr *sechdrs,
+static int apply_relocations(Elf32_Shdr *sechdrs,
 		      const char *strtab,
 		      unsigned int symindex,
 		      unsigned int relsec,
@@ -596,7 +595,7 @@ int apply_relocations(Elf32_Shdr *sechdrs,
 	return 0;
 }
 
-void save_gp_address(unsigned int secbase, unsigned int rel)
+static inline void save_gp_address(unsigned int secbase, unsigned int rel)
 {
 	gp_addr = secbase + rel;
 	gp_offs = gp_addr - (secbase & 0xffff0000);
-- 
GitLab


From 349c4229ed305146a558008d393c622d715cd11d Mon Sep 17 00:00:00 2001
From: Ralf Baechle <ralf@linux-mips.org>
Date: Mon, 3 Aug 2009 12:56:39 +0100
Subject: [PATCH 0492/1153] MIPS: VPE: Fix bogus indentation.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/kernel/vpe.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c
index 6cbeb2a5452..e3687524fdb 100644
--- a/arch/mips/kernel/vpe.c
+++ b/arch/mips/kernel/vpe.c
@@ -73,7 +73,7 @@ static int major;
 static const int minor = 1;	/* fixed for now  */
 
 #ifdef CONFIG_MIPS_APSP_KSPD
- static struct kspd_notifications kspd_events;
+static struct kspd_notifications kspd_events;
 static int kspd_events_reqd = 0;
 #endif
 
-- 
GitLab


From ce21f4e86f89d352efecd044958db1917033b49b Mon Sep 17 00:00:00 2001
From: Ralf Baechle <ralf@linux-mips.org>
Date: Mon, 3 Aug 2009 12:57:52 +0100
Subject: [PATCH 0493/1153] MIPS: VPE: Delete unused function get_tc_unused().

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/kernel/vpe.c | 12 ------------
 1 file changed, 12 deletions(-)

diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c
index e3687524fdb..9a1ab7e87fd 100644
--- a/arch/mips/kernel/vpe.c
+++ b/arch/mips/kernel/vpe.c
@@ -185,18 +185,6 @@ static struct tc *get_tc(int index)
 	return NULL;
 }
 
-struct tc *get_tc_unused(void)
-{
-	struct tc *t;
-
-	list_for_each_entry(t, &vpecontrol.tc_list, list) {
-		if (t->state == TC_STATE_UNUSED)
-			return t;
-	}
-
-	return NULL;
-}
-
 /* allocate a vpe and associate it with this minor (or index) */
 static struct vpe *alloc_vpe(int minor)
 {
-- 
GitLab


From 54822de7793bf9aa56d79cc173281cdb23b37f9f Mon Sep 17 00:00:00 2001
From: Ralf Baechle <ralf@linux-mips.org>
Date: Mon, 3 Aug 2009 17:27:19 +0100
Subject: [PATCH 0494/1153] MIPS: Wire up accept4 syscall.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/include/asm/unistd.h | 15 +++++++++------
 arch/mips/kernel/scall32-o32.S |  1 +
 arch/mips/kernel/scall64-64.S  |  1 +
 arch/mips/kernel/scall64-n32.S |  1 +
 arch/mips/kernel/scall64-o32.S |  1 +
 5 files changed, 13 insertions(+), 6 deletions(-)

diff --git a/arch/mips/include/asm/unistd.h b/arch/mips/include/asm/unistd.h
index b70c49fdda2..e753a777949 100644
--- a/arch/mips/include/asm/unistd.h
+++ b/arch/mips/include/asm/unistd.h
@@ -354,16 +354,17 @@
 #define __NR_pwritev			(__NR_Linux + 331)
 #define __NR_rt_tgsigqueueinfo		(__NR_Linux + 332)
 #define __NR_perf_counter_open		(__NR_Linux + 333)
+#define __NR_accept4			(__NR_Linux + 334)
 
 /*
  * Offset of the last Linux o32 flavoured syscall
  */
-#define __NR_Linux_syscalls		333
+#define __NR_Linux_syscalls		334
 
 #endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
 
 #define __NR_O32_Linux			4000
-#define __NR_O32_Linux_syscalls		333
+#define __NR_O32_Linux_syscalls		334
 
 #if _MIPS_SIM == _MIPS_SIM_ABI64
 
@@ -664,16 +665,17 @@
 #define __NR_pwritev			(__NR_Linux + 290)
 #define __NR_rt_tgsigqueueinfo		(__NR_Linux + 291)
 #define __NR_perf_counter_open		(__NR_Linux + 292)
+#define __NR_accept4			(__NR_Linux + 293)
 
 /*
  * Offset of the last Linux 64-bit flavoured syscall
  */
-#define __NR_Linux_syscalls		292
+#define __NR_Linux_syscalls		293
 
 #endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */
 
 #define __NR_64_Linux			5000
-#define __NR_64_Linux_syscalls		292
+#define __NR_64_Linux_syscalls		293
 
 #if _MIPS_SIM == _MIPS_SIM_NABI32
 
@@ -978,16 +980,17 @@
 #define __NR_pwritev			(__NR_Linux + 294)
 #define __NR_rt_tgsigqueueinfo		(__NR_Linux + 295)
 #define __NR_perf_counter_open		(__NR_Linux + 296)
+#define __NR_accept4			(__NR_Linux + 297)
 
 /*
  * Offset of the last N32 flavoured syscall
  */
-#define __NR_Linux_syscalls		296
+#define __NR_Linux_syscalls		297
 
 #endif /* _MIPS_SIM == _MIPS_SIM_NABI32 */
 
 #define __NR_N32_Linux			6000
-#define __NR_N32_Linux_syscalls		296
+#define __NR_N32_Linux_syscalls		297
 
 #ifdef __KERNEL__
 
diff --git a/arch/mips/kernel/scall32-o32.S b/arch/mips/kernel/scall32-o32.S
index 20a86e08fd5..b5708212353 100644
--- a/arch/mips/kernel/scall32-o32.S
+++ b/arch/mips/kernel/scall32-o32.S
@@ -654,6 +654,7 @@ einval:	li	v0, -ENOSYS
 	sys	sys_pwritev		6
 	sys	sys_rt_tgsigqueueinfo	4
 	sys	sys_perf_counter_open	5
+	sys	sys_accept4		4
 	.endm
 
 	/* We pre-compute the number of _instruction_ bytes needed to
diff --git a/arch/mips/kernel/scall64-64.S b/arch/mips/kernel/scall64-64.S
index b046130d4c5..3d866f24e06 100644
--- a/arch/mips/kernel/scall64-64.S
+++ b/arch/mips/kernel/scall64-64.S
@@ -491,4 +491,5 @@ sys_call_table:
 	PTR	sys_pwritev			/* 5390 */
 	PTR	sys_rt_tgsigqueueinfo
 	PTR	sys_perf_counter_open
+	PTR	sys_accept4
 	.size	sys_call_table,.-sys_call_table
diff --git a/arch/mips/kernel/scall64-n32.S b/arch/mips/kernel/scall64-n32.S
index 15874f9812c..e855b118a07 100644
--- a/arch/mips/kernel/scall64-n32.S
+++ b/arch/mips/kernel/scall64-n32.S
@@ -417,4 +417,5 @@ EXPORT(sysn32_call_table)
 	PTR	sys_pwritev
 	PTR	compat_sys_rt_tgsigqueueinfo	/* 5295 */
 	PTR	sys_perf_counter_open
+	PTR	sys_accept4
 	.size	sysn32_call_table,.-sysn32_call_table
diff --git a/arch/mips/kernel/scall64-o32.S b/arch/mips/kernel/scall64-o32.S
index 781e0f1e953..0c49f1a660b 100644
--- a/arch/mips/kernel/scall64-o32.S
+++ b/arch/mips/kernel/scall64-o32.S
@@ -537,4 +537,5 @@ sys_call_table:
 	PTR	compat_sys_pwritev
 	PTR	compat_sys_rt_tgsigqueueinfo
 	PTR	sys_perf_counter_open
+	PTR	sys_accept4
 	.size	sys_call_table,.-sys_call_table
-- 
GitLab


From 8523acfe40efc1a8d3da8f473ca67cb195b06f0c Mon Sep 17 00:00:00 2001
From: Thomas Hellstrom <thellstrom@vmware.com>
Date: Mon, 3 Aug 2009 09:25:45 +0200
Subject: [PATCH 0495/1153] x86: Fix CPA memtype reserving in the
 set_pages_array*() cases

The code was incorrectly reserving memtypes using the page
virtual address instead of the physical address. Furthermore,
the code was not ignoring highmem pages as it ought to.

( upstream does not pass in highmem pages yet - but upcoming
  graphics code will do it and there's no reason to not handle
  this properly in the CPA APIs.)

Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=13884

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: <stable@kernel.org>
Cc: dri-devel@lists.sourceforge.net
Cc: venkatesh.pallipadi@intel.com
LKML-Reference: <1249284345-7654-1-git-send-email-thellstrom@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/mm/pageattr.c | 30 +++++++++++++++++++++---------
 1 file changed, 21 insertions(+), 9 deletions(-)

diff --git a/arch/x86/mm/pageattr.c b/arch/x86/mm/pageattr.c
index 895d90e1a81..7e600c1962d 100644
--- a/arch/x86/mm/pageattr.c
+++ b/arch/x86/mm/pageattr.c
@@ -591,9 +591,12 @@ static int __change_page_attr(struct cpa_data *cpa, int primary)
 	unsigned int level;
 	pte_t *kpte, old_pte;
 
-	if (cpa->flags & CPA_PAGES_ARRAY)
-		address = (unsigned long)page_address(cpa->pages[cpa->curpage]);
-	else if (cpa->flags & CPA_ARRAY)
+	if (cpa->flags & CPA_PAGES_ARRAY) {
+		struct page *page = cpa->pages[cpa->curpage];
+		if (unlikely(PageHighMem(page)))
+			return 0;
+		address = (unsigned long)page_address(page);
+	} else if (cpa->flags & CPA_ARRAY)
 		address = cpa->vaddr[cpa->curpage];
 	else
 		address = *cpa->vaddr;
@@ -697,9 +700,12 @@ static int cpa_process_alias(struct cpa_data *cpa)
 	 * No need to redo, when the primary call touched the direct
 	 * mapping already:
 	 */
-	if (cpa->flags & CPA_PAGES_ARRAY)
-		vaddr = (unsigned long)page_address(cpa->pages[cpa->curpage]);
-	else if (cpa->flags & CPA_ARRAY)
+	if (cpa->flags & CPA_PAGES_ARRAY) {
+		struct page *page = cpa->pages[cpa->curpage];
+		if (unlikely(PageHighMem(page)))
+			return 0;
+		vaddr = (unsigned long)page_address(page);
+	} else if (cpa->flags & CPA_ARRAY)
 		vaddr = cpa->vaddr[cpa->curpage];
 	else
 		vaddr = *cpa->vaddr;
@@ -1122,7 +1128,9 @@ int set_pages_array_uc(struct page **pages, int addrinarray)
 	int free_idx;
 
 	for (i = 0; i < addrinarray; i++) {
-		start = (unsigned long)page_address(pages[i]);
+		if (PageHighMem(pages[i]))
+			continue;
+		start = page_to_pfn(pages[i]) << PAGE_SHIFT;
 		end = start + PAGE_SIZE;
 		if (reserve_memtype(start, end, _PAGE_CACHE_UC_MINUS, NULL))
 			goto err_out;
@@ -1135,7 +1143,9 @@ int set_pages_array_uc(struct page **pages, int addrinarray)
 err_out:
 	free_idx = i;
 	for (i = 0; i < free_idx; i++) {
-		start = (unsigned long)page_address(pages[i]);
+		if (PageHighMem(pages[i]))
+			continue;
+		start = page_to_pfn(pages[i]) << PAGE_SHIFT;
 		end = start + PAGE_SIZE;
 		free_memtype(start, end);
 	}
@@ -1164,7 +1174,9 @@ int set_pages_array_wb(struct page **pages, int addrinarray)
 		return retval;
 
 	for (i = 0; i < addrinarray; i++) {
-		start = (unsigned long)page_address(pages[i]);
+		if (PageHighMem(pages[i]))
+			continue;
+		start = page_to_pfn(pages[i]) << PAGE_SHIFT;
 		end = start + PAGE_SIZE;
 		free_memtype(start, end);
 	}
-- 
GitLab


From af0d3b103bcfa877343ee338de12002cd50c9ee5 Mon Sep 17 00:00:00 2001
From: Dave Young <hidave.darkstar@gmail.com>
Date: Mon, 3 Aug 2009 04:26:16 +0000
Subject: [PATCH 0496/1153] bluetooth: rfcomm_init bug fix

rfcomm tty may be used before rfcomm_tty_driver initilized,
The problem is that now socket layer init before tty layer, if userspace
program do socket callback right here then oops will happen.

reporting in:
http://marc.info/?l=linux-bluetooth&m=124404919324542&w=2

make 3 changes:
1. remove #ifdef in rfcomm/core.c,
make it blank function when rfcomm tty not selected in rfcomm.h

2. tune the rfcomm_init error patch to ensure
tty driver initilized before rfcomm socket usage.

3. remove __exit for rfcomm_cleanup_sockets
because above change need call it in a __init function.

Reported-by: Oliver Hartkopp <oliver@hartkopp.net>
Tested-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 include/net/bluetooth/rfcomm.h | 12 +++++++++++-
 net/bluetooth/rfcomm/core.c    | 27 +++++++++++++++++++--------
 net/bluetooth/rfcomm/sock.c    |  2 +-
 3 files changed, 31 insertions(+), 10 deletions(-)

diff --git a/include/net/bluetooth/rfcomm.h b/include/net/bluetooth/rfcomm.h
index 80072611d26..c274993234e 100644
--- a/include/net/bluetooth/rfcomm.h
+++ b/include/net/bluetooth/rfcomm.h
@@ -355,7 +355,17 @@ struct rfcomm_dev_list_req {
 };
 
 int  rfcomm_dev_ioctl(struct sock *sk, unsigned int cmd, void __user *arg);
+
+#ifdef CONFIG_BT_RFCOMM_TTY
 int  rfcomm_init_ttys(void);
 void rfcomm_cleanup_ttys(void);
-
+#else
+static inline int rfcomm_init_ttys(void)
+{
+	return 0;
+}
+static inline void rfcomm_cleanup_ttys(void)
+{
+}
+#endif
 #endif /* __RFCOMM_H */
diff --git a/net/bluetooth/rfcomm/core.c b/net/bluetooth/rfcomm/core.c
index e50566ebf9f..94b3388c188 100644
--- a/net/bluetooth/rfcomm/core.c
+++ b/net/bluetooth/rfcomm/core.c
@@ -2080,28 +2080,41 @@ static CLASS_ATTR(rfcomm_dlc, S_IRUGO, rfcomm_dlc_sysfs_show, NULL);
 /* ---- Initialization ---- */
 static int __init rfcomm_init(void)
 {
+	int ret;
+
 	l2cap_load();
 
 	hci_register_cb(&rfcomm_cb);
 
 	rfcomm_thread = kthread_run(rfcomm_run, NULL, "krfcommd");
 	if (IS_ERR(rfcomm_thread)) {
-		hci_unregister_cb(&rfcomm_cb);
-		return PTR_ERR(rfcomm_thread);
+		ret = PTR_ERR(rfcomm_thread);
+		goto out_thread;
 	}
 
 	if (class_create_file(bt_class, &class_attr_rfcomm_dlc) < 0)
 		BT_ERR("Failed to create RFCOMM info file");
 
-	rfcomm_init_sockets();
+	ret = rfcomm_init_ttys();
+	if (ret)
+		goto out_tty;
 
-#ifdef CONFIG_BT_RFCOMM_TTY
-	rfcomm_init_ttys();
-#endif
+	ret = rfcomm_init_sockets();
+	if (ret)
+		goto out_sock;
 
 	BT_INFO("RFCOMM ver %s", VERSION);
 
 	return 0;
+
+out_sock:
+	rfcomm_cleanup_ttys();
+out_tty:
+	kthread_stop(rfcomm_thread);
+out_thread:
+	hci_unregister_cb(&rfcomm_cb);
+
+	return ret;
 }
 
 static void __exit rfcomm_exit(void)
@@ -2112,9 +2125,7 @@ static void __exit rfcomm_exit(void)
 
 	kthread_stop(rfcomm_thread);
 
-#ifdef CONFIG_BT_RFCOMM_TTY
 	rfcomm_cleanup_ttys();
-#endif
 
 	rfcomm_cleanup_sockets();
 }
diff --git a/net/bluetooth/rfcomm/sock.c b/net/bluetooth/rfcomm/sock.c
index 7f482784e9f..0b85e811685 100644
--- a/net/bluetooth/rfcomm/sock.c
+++ b/net/bluetooth/rfcomm/sock.c
@@ -1132,7 +1132,7 @@ error:
 	return err;
 }
 
-void __exit rfcomm_cleanup_sockets(void)
+void rfcomm_cleanup_sockets(void)
 {
 	class_remove_file(bt_class, &class_attr_rfcomm);
 
-- 
GitLab


From 202ff1ec8e53d5dd36e1a5bd4b0a7ed7dbd45087 Mon Sep 17 00:00:00 2001
From: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Date: Mon, 3 Aug 2009 07:20:38 +0000
Subject: [PATCH 0497/1153] ixgbe: Patch to modify 82598 PCIe completion
 timeout values

The default completion timeout values for 82598 should be in the
range of 50us to 50ms, however the hardware default for these
parts is 500us to 1ms which is less than the 10ms recommended by
the pcie spec. To address this we need to increase the value to
either 10ms to 250ms for capability version 1 configuration, or
16ms to 55ms for version 2.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ixgbe/ixgbe_82598.c | 67 ++++++++++++++++++++++++++++++++-
 drivers/net/ixgbe/ixgbe_type.h  |  8 ++++
 2 files changed, 74 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c
index b9923047ce1..522c03bc1da 100644
--- a/drivers/net/ixgbe/ixgbe_82598.c
+++ b/drivers/net/ixgbe/ixgbe_82598.c
@@ -49,6 +49,51 @@ static s32 ixgbe_setup_copper_link_speed_82598(struct ixgbe_hw *hw,
 static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
                                        u8 *eeprom_data);
 
+/**
+ *  ixgbe_set_pcie_completion_timeout - set pci-e completion timeout
+ *  @hw: pointer to the HW structure
+ *
+ *  The defaults for 82598 should be in the range of 50us to 50ms,
+ *  however the hardware default for these parts is 500us to 1ms which is less
+ *  than the 10ms recommended by the pci-e spec.  To address this we need to
+ *  increase the value to either 10ms to 250ms for capability version 1 config,
+ *  or 16ms to 55ms for version 2.
+ **/
+void ixgbe_set_pcie_completion_timeout(struct ixgbe_hw *hw)
+{
+	struct ixgbe_adapter *adapter = hw->back;
+	u32 gcr = IXGBE_READ_REG(hw, IXGBE_GCR);
+	u16 pcie_devctl2;
+
+	/* only take action if timeout value is defaulted to 0 */
+	if (gcr & IXGBE_GCR_CMPL_TMOUT_MASK)
+		goto out;
+
+	/*
+	 * if capababilities version is type 1 we can write the
+	 * timeout of 10ms to 250ms through the GCR register
+	 */
+	if (!(gcr & IXGBE_GCR_CAP_VER2)) {
+		gcr |= IXGBE_GCR_CMPL_TMOUT_10ms;
+		goto out;
+	}
+
+	/*
+	 * for version 2 capabilities we need to write the config space
+	 * directly in order to set the completion timeout value for
+	 * 16ms to 55ms
+	 */
+	pci_read_config_word(adapter->pdev,
+	                     IXGBE_PCI_DEVICE_CONTROL2, &pcie_devctl2);
+	pcie_devctl2 |= IXGBE_PCI_DEVICE_CONTROL2_16ms;
+	pci_write_config_word(adapter->pdev,
+	                      IXGBE_PCI_DEVICE_CONTROL2, pcie_devctl2);
+out:
+	/* disable completion timeout resend */
+	gcr &= ~IXGBE_GCR_CMPL_TMOUT_RESEND;
+	IXGBE_WRITE_REG(hw, IXGBE_GCR, gcr);
+}
+
 /**
  *  ixgbe_get_pcie_msix_count_82598 - Gets MSI-X vector count
  *  @hw: pointer to hardware structure
@@ -152,6 +197,26 @@ out:
 	return ret_val;
 }
 
+/**
+ *  ixgbe_start_hw_82598 - Prepare hardware for Tx/Rx
+ *  @hw: pointer to hardware structure
+ *
+ *  Starts the hardware using the generic start_hw function.
+ *  Then set pcie completion timeout
+ **/
+s32 ixgbe_start_hw_82598(struct ixgbe_hw *hw)
+{
+	s32 ret_val = 0;
+
+	ret_val = ixgbe_start_hw_generic(hw);
+
+	/* set the completion timeout for interface */
+	if (ret_val == 0)
+		ixgbe_set_pcie_completion_timeout(hw);
+
+	return ret_val;
+}
+
 /**
  *  ixgbe_get_link_capabilities_82598 - Determines link capabilities
  *  @hw: pointer to hardware structure
@@ -1085,7 +1150,7 @@ out:
 static struct ixgbe_mac_operations mac_ops_82598 = {
 	.init_hw		= &ixgbe_init_hw_generic,
 	.reset_hw		= &ixgbe_reset_hw_82598,
-	.start_hw		= &ixgbe_start_hw_generic,
+	.start_hw		= &ixgbe_start_hw_82598,
 	.clear_hw_cntrs		= &ixgbe_clear_hw_cntrs_generic,
 	.get_media_type		= &ixgbe_get_media_type_82598,
 	.get_supported_physical_layer = &ixgbe_get_supported_physical_layer_82598,
diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h
index fa87309dc08..be90eb4575f 100644
--- a/drivers/net/ixgbe/ixgbe_type.h
+++ b/drivers/net/ixgbe/ixgbe_type.h
@@ -718,6 +718,12 @@
 #define IXGBE_ECC_STATUS_82599  0x110E0
 #define IXGBE_BAR_CTRL_82599    0x110F4
 
+/* PCI Express Control */
+#define IXGBE_GCR_CMPL_TMOUT_MASK       0x0000F000
+#define IXGBE_GCR_CMPL_TMOUT_10ms       0x00001000
+#define IXGBE_GCR_CMPL_TMOUT_RESEND     0x00010000
+#define IXGBE_GCR_CAP_VER2              0x00040000
+
 /* Time Sync Registers */
 #define IXGBE_TSYNCRXCTL 0x05188 /* Rx Time Sync Control register - RW */
 #define IXGBE_TSYNCTXCTL 0x08C00 /* Tx Time Sync Control register - RW */
@@ -1521,6 +1527,7 @@
 
 /* PCI Bus Info */
 #define IXGBE_PCI_LINK_STATUS     0xB2
+#define IXGBE_PCI_DEVICE_CONTROL2 0xC8
 #define IXGBE_PCI_LINK_WIDTH      0x3F0
 #define IXGBE_PCI_LINK_WIDTH_1    0x10
 #define IXGBE_PCI_LINK_WIDTH_2    0x20
@@ -1531,6 +1538,7 @@
 #define IXGBE_PCI_LINK_SPEED_5000 0x2
 #define IXGBE_PCI_HEADER_TYPE_REGISTER  0x0E
 #define IXGBE_PCI_HEADER_TYPE_MULTIFUNC 0x80
+#define IXGBE_PCI_DEVICE_CONTROL2_16ms  0x0005
 
 /* Number of 100 microseconds we wait for PCI Express master disable */
 #define IXGBE_PCI_MASTER_DISABLE_TIMEOUT 800
-- 
GitLab


From cd3468bad96c00b5a512f551674f36776129520e Mon Sep 17 00:00:00 2001
From: Johannes Berg <johannes@sipsolutions.net>
Date: Wed, 29 Jul 2009 22:07:44 +0200
Subject: [PATCH 0498/1153] cfg80211: add two missing NULL pointer checks

These pointers can be NULL, the is_mesh() case isn't
ever hit in the current kernel, but cmp_ies() can be
hit under certain conditions.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29, 2.6.30]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 net/wireless/scan.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/net/wireless/scan.c b/net/wireless/scan.c
index 9271118e1fc..7e595ce24ee 100644
--- a/net/wireless/scan.c
+++ b/net/wireless/scan.c
@@ -118,7 +118,7 @@ static int cmp_ies(u8 num, u8 *ies1, size_t len1, u8 *ies2, size_t len2)
 
 	if (!ie1 && !ie2)
 		return 0;
-	if (!ie1)
+	if (!ie1 || !ie2)
 		return -1;
 
 	r = memcmp(ie1 + 2, ie2 + 2, min(ie1[1], ie2[1]));
@@ -171,6 +171,8 @@ static bool is_mesh(struct cfg80211_bss *a,
 	ie = find_ie(WLAN_EID_MESH_CONFIG,
 		     a->information_elements,
 		     a->len_information_elements);
+	if (!ie)
+		return false;
 	if (ie[1] != IEEE80211_MESH_CONFIG_LEN)
 		return false;
 
-- 
GitLab


From 371842448c05b42d11a4be1c8e4e81d62ecc7534 Mon Sep 17 00:00:00 2001
From: "Luis R. Rodriguez" <lrodriguez@atheros.com>
Date: Thu, 30 Jul 2009 17:43:48 -0700
Subject: [PATCH 0499/1153] cfg80211: fix regression on beacon world roaming
 feature

A regression was added through patch a4ed90d6:

"cfg80211: respect API on orig_flags on channel for beacon hint"

We did indeed respect _orig flags but the intention was not clearly
stated in the commit log. This patch fixes firmware issues picked
up by iwlwifi when we lift passive scan of beaconing restrictions
on channels its EEPROM has been configured to always enable.

By doing so though we also disallowed beacon hints on devices
registering their wiphy with custom world regulatory domains
enabled, this happens to be currently ath5k, ath9k and ar9170.
The passive scan and beacon restrictions on those devices would
never be lifted even if we did find a beacon and the hardware did
support such enhancements when world roaming.

Since Johannes indicates iwlwifi firmware cannot be changed to
allow beacon hinting we set up a flag now to specifically allow
drivers to disable beacon hints for devices which cannot use them.

We enable the flag on iwlwifi to disable beacon hints and by default
enable it for all other drivers. It should be noted beacon hints lift
passive scan flags and beacon restrictions when we receive a beacon from
an AP on any 5 GHz non-DFS channels, and channels 12-14 on the 2.4 GHz
band. We don't bother with channels 1-11 as those channels are allowed
world wide.

This should fix world roaming for ath5k, ath9k and ar9170, thereby
improving scan time when we receive the first beacon from any AP,
and also enabling beaconing operation (AP/IBSS/Mesh) on cards which
would otherwise not be allowed to do so. Drivers not using custom
regulatory stuff (wiphy_apply_custom_regulatory()) were not affected
by this as the orig_flags for the channels would have been cleared
upon wiphy registration.

I tested this with a world roaming ath5k card.

Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/iwlwifi/iwl-core.c     | 3 +++
 drivers/net/wireless/iwlwifi/iwl3945-base.c | 3 +++
 include/net/cfg80211.h                      | 5 +++++
 net/wireless/reg.c                          | 9 +++++----
 net/wireless/reg.h                          | 3 ++-
 5 files changed, 18 insertions(+), 5 deletions(-)

diff --git a/drivers/net/wireless/iwlwifi/iwl-core.c b/drivers/net/wireless/iwlwifi/iwl-core.c
index 6ab07165ea2..18b135f510e 100644
--- a/drivers/net/wireless/iwlwifi/iwl-core.c
+++ b/drivers/net/wireless/iwlwifi/iwl-core.c
@@ -1332,6 +1332,9 @@ int iwl_setup_mac(struct iwl_priv *priv)
 
 	hw->wiphy->custom_regulatory = true;
 
+	/* Firmware does not support this */
+	hw->wiphy->disable_beacon_hints = true;
+
 	hw->wiphy->max_scan_ssids = PROBE_OPTION_MAX;
 	/* we create the 802.11 header and a zero-length SSID element */
 	hw->wiphy->max_scan_ie_len = IWL_MAX_PROBE_REQUEST - 24 - 2;
diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c
index 2f50ab60bfd..523843369ca 100644
--- a/drivers/net/wireless/iwlwifi/iwl3945-base.c
+++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c
@@ -3968,6 +3968,9 @@ static int iwl3945_setup_mac(struct iwl_priv *priv)
 
 	hw->wiphy->custom_regulatory = true;
 
+	/* Firmware does not support this */
+	hw->wiphy->disable_beacon_hints = true;
+
 	hw->wiphy->max_scan_ssids = PROBE_OPTION_MAX_3945;
 	/* we create the 802.11 header and a zero-length SSID element */
 	hw->wiphy->max_scan_ie_len = IWL_MAX_PROBE_REQUEST - 24 - 2;
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 1a21895b732..d1892d66701 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -979,6 +979,10 @@ struct cfg80211_ops {
  * 	channels at a later time. This can be used for devices which do not
  * 	have calibration information gauranteed for frequencies or settings
  * 	outside of its regulatory domain.
+ * @disable_beacon_hints: enable this if your driver needs to ensure that
+ *	passive scan flags and beaconing flags may not be lifted by cfg80211
+ *	due to regulatory beacon hints. For more information on beacon
+ *	hints read the documenation for regulatory_hint_found_beacon()
  * @reg_notifier: the driver's regulatory notification callback
  * @regd: the driver's regulatory domain, if one was requested via
  * 	the regulatory_hint() API. This can be used by the driver
@@ -1004,6 +1008,7 @@ struct wiphy {
 
 	bool custom_regulatory;
 	bool strict_regulatory;
+	bool disable_beacon_hints;
 
 	enum cfg80211_signal_type signal_type;
 
diff --git a/net/wireless/reg.c b/net/wireless/reg.c
index 5e14371cda7..75a406d3361 100644
--- a/net/wireless/reg.c
+++ b/net/wireless/reg.c
@@ -1089,17 +1089,18 @@ static void handle_reg_beacon(struct wiphy *wiphy,
 
 	chan->beacon_found = true;
 
+	if (wiphy->disable_beacon_hints)
+		return;
+
 	chan_before.center_freq = chan->center_freq;
 	chan_before.flags = chan->flags;
 
-	if ((chan->flags & IEEE80211_CHAN_PASSIVE_SCAN) &&
-	    !(chan->orig_flags & IEEE80211_CHAN_PASSIVE_SCAN)) {
+	if (chan->flags & IEEE80211_CHAN_PASSIVE_SCAN) {
 		chan->flags &= ~IEEE80211_CHAN_PASSIVE_SCAN;
 		channel_changed = true;
 	}
 
-	if ((chan->flags & IEEE80211_CHAN_NO_IBSS) &&
-	    !(chan->orig_flags & IEEE80211_CHAN_NO_IBSS)) {
+	if (chan->flags & IEEE80211_CHAN_NO_IBSS) {
 		chan->flags &= ~IEEE80211_CHAN_NO_IBSS;
 		channel_changed = true;
 	}
diff --git a/net/wireless/reg.h b/net/wireless/reg.h
index e37829a49dc..4e167a8e11b 100644
--- a/net/wireless/reg.h
+++ b/net/wireless/reg.h
@@ -30,7 +30,8 @@ int set_regdom(const struct ieee80211_regdomain *rd);
  * non-radar 5 GHz channels.
  *
  * Drivers do not need to call this, cfg80211 will do it for after a scan
- * on a newly found BSS.
+ * on a newly found BSS. If you cannot make use of this feature you can
+ * set the wiphy->disable_beacon_hints to true.
  */
 int regulatory_hint_found_beacon(struct wiphy *wiphy,
 					struct ieee80211_channel *beacon_chan,
-- 
GitLab


From dbc1eec485625228895ded6baf6bd01ce2475410 Mon Sep 17 00:00:00 2001
From: Patrick Simmons <linuxrocks123@netscape.net>
Date: Sun, 2 Aug 2009 02:46:28 -0600
Subject: [PATCH 0500/1153] zd1211rw: fix unaligned access in zd_mac_rx

Fix an unaligned memory access in the zd_mac_rx function of zd1211rw
that causes problems on SPARC64.

Signed-off-by: Patrick Simmons <linuxrocks123@netscape.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/zd1211rw/zd_mac.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/zd1211rw/zd_mac.c b/drivers/net/wireless/zd1211rw/zd_mac.c
index 40b07b98822..3bd3c779fff 100644
--- a/drivers/net/wireless/zd1211rw/zd_mac.c
+++ b/drivers/net/wireless/zd1211rw/zd_mac.c
@@ -698,7 +698,7 @@ int zd_mac_rx(struct ieee80211_hw *hw, const u8 *buffer, unsigned int length)
 			&& !mac->pass_ctrl)
 		return 0;
 
-	fc = *(__le16 *)buffer;
+	fc = get_unaligned((__le16*)buffer);
 	need_padding = ieee80211_is_data_qos(fc) ^ ieee80211_has_a4(fc);
 
 	skb = dev_alloc_skb(length + (need_padding ? 2 : 0));
-- 
GitLab


From c37457e69ffd7d3c94cbfcc1c39be9a45dd7ad21 Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Mon, 3 Aug 2009 11:11:45 +0200
Subject: [PATCH 0501/1153] drivers/net/wireless/iwlwifi: introduce missing
 kfree

Move orthogonal error handling code up before a kzalloc, so that it
doesn't have to free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
(
x->f1 = E
|
 (x->f1 == NULL || ...)
|
 f(...,x->f1,...)
)
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/iwlwifi/iwl-debugfs.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/iwlwifi/iwl-debugfs.c b/drivers/net/wireless/iwlwifi/iwl-debugfs.c
index 11e08c06891..ca00cc8ad4c 100644
--- a/drivers/net/wireless/iwlwifi/iwl-debugfs.c
+++ b/drivers/net/wireless/iwlwifi/iwl-debugfs.c
@@ -308,18 +308,18 @@ static ssize_t iwl_dbgfs_nvm_read(struct file *file,
 		return -ENODATA;
 	}
 
+	ptr = priv->eeprom;
+	if (!ptr) {
+		IWL_ERR(priv, "Invalid EEPROM/OTP memory\n");
+		return -ENOMEM;
+	}
+
 	/* 4 characters for byte 0xYY */
 	buf = kzalloc(buf_size, GFP_KERNEL);
 	if (!buf) {
 		IWL_ERR(priv, "Can not allocate Buffer\n");
 		return -ENOMEM;
 	}
-
-	ptr = priv->eeprom;
-	if (!ptr) {
-		IWL_ERR(priv, "Invalid EEPROM/OTP memory\n");
-		return -ENOMEM;
-	}
 	pos += scnprintf(buf + pos, buf_size - pos, "NVM Type: %s\n",
 			(priv->nvm_device_type == NVM_DEVICE_TYPE_OTP)
 			? "OTP" : "EEPROM");
-- 
GitLab


From 9f9857bb5e147b977b9878c46e3dd87c9e8caf50 Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Sat, 1 Aug 2009 10:55:53 +0200
Subject: [PATCH 0502/1153] drivers/net/wireless: introduce missing kfree

Error handling code following a kzalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
(
x->f1 = E
|
 (x->f1 == NULL || ...)
|
 f(...,x->f1,...)
)
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/iwmc3200wifi/commands.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/wireless/iwmc3200wifi/commands.c b/drivers/net/wireless/iwmc3200wifi/commands.c
index 834a7f544e5..e2334d12359 100644
--- a/drivers/net/wireless/iwmc3200wifi/commands.c
+++ b/drivers/net/wireless/iwmc3200wifi/commands.c
@@ -220,6 +220,7 @@ int iwm_store_rxiq_calib_result(struct iwm_priv *iwm)
 	eeprom_rxiq = iwm_eeprom_access(iwm, IWM_EEPROM_CALIB_RXIQ);
 	if (IS_ERR(eeprom_rxiq)) {
 		IWM_ERR(iwm, "Couldn't access EEPROM RX IQ entry\n");
+		kfree(rxiq);
 		return PTR_ERR(eeprom_rxiq);
 	}
 
-- 
GitLab


From b929c633b4067be18a335d278a66fd5deef3cabe Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Sun, 2 Aug 2009 09:44:12 +0200
Subject: [PATCH 0503/1153] libertas: Read buffer overflow

Check whether index is within bounds before testing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/libertas/11d.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/libertas/11d.c b/drivers/net/wireless/libertas/11d.c
index 9a5408e7d94..5c6968101f0 100644
--- a/drivers/net/wireless/libertas/11d.c
+++ b/drivers/net/wireless/libertas/11d.c
@@ -47,7 +47,7 @@ static u8 lbs_region_2_code(u8 *region)
 {
 	u8 i;
 
-	for (i = 0; region[i] && i < COUNTRY_CODE_LEN; i++)
+	for (i = 0; i < COUNTRY_CODE_LEN && region[i]; i++)
 		region[i] = toupper(region[i]);
 
 	for (i = 0; i < ARRAY_SIZE(region_code_mapping); i++) {
-- 
GitLab


From 99f1b01562b7dcae75b043114f76163fbf84fcab Mon Sep 17 00:00:00 2001
From: Reinette Chatre <reinette.chatre@intel.com>
Date: Mon, 3 Aug 2009 12:10:16 -0700
Subject: [PATCH 0504/1153] iwlagn: do not send key clear commands when rfkill
 enabled

Do all key clearing except sending sommands to device when rfkill
enabled. When rfkill enabled the interface is brought down and will
be brought back up correctly after rfkill is enabled again.

Same change is not needed for iwl3945 as it ignores return code when
sending key clearing command to device.

This fixes http://bugzilla.kernel.org/show_bug.cgi?id=13742

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/iwlwifi/iwl-sta.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/drivers/net/wireless/iwlwifi/iwl-sta.c b/drivers/net/wireless/iwlwifi/iwl-sta.c
index 2addf735b19..ffd5c61a755 100644
--- a/drivers/net/wireless/iwlwifi/iwl-sta.c
+++ b/drivers/net/wireless/iwlwifi/iwl-sta.c
@@ -566,6 +566,8 @@ int iwl_remove_default_wep_key(struct iwl_priv *priv,
 	unsigned long flags;
 
 	spin_lock_irqsave(&priv->sta_lock, flags);
+	IWL_DEBUG_WEP(priv, "Removing default WEP key: idx=%d\n",
+		      keyconf->keyidx);
 
 	if (!test_and_clear_bit(keyconf->keyidx, &priv->ucode_key_table))
 		IWL_ERR(priv, "index %d not used in uCode key table.\n",
@@ -573,6 +575,11 @@ int iwl_remove_default_wep_key(struct iwl_priv *priv,
 
 	priv->default_wep_key--;
 	memset(&priv->wep_keys[keyconf->keyidx], 0, sizeof(priv->wep_keys[0]));
+	if (iwl_is_rfkill(priv)) {
+		IWL_DEBUG_WEP(priv, "Not sending REPLY_WEPKEY command due to RFKILL.\n");
+		spin_unlock_irqrestore(&priv->sta_lock, flags);
+		return 0;
+	}
 	ret = iwl_send_static_wepkey_cmd(priv, 1);
 	IWL_DEBUG_WEP(priv, "Remove default WEP key: idx=%d ret=%d\n",
 		      keyconf->keyidx, ret);
@@ -853,6 +860,11 @@ int iwl_remove_dynamic_key(struct iwl_priv *priv,
 	priv->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK;
 	priv->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK;
 
+	if (iwl_is_rfkill(priv)) {
+		IWL_DEBUG_WEP(priv, "Not sending REPLY_ADD_STA command because RFKILL enabled. \n");
+		spin_unlock_irqrestore(&priv->sta_lock, flags);
+		return 0;
+	}
 	ret =  iwl_send_add_sta(priv, &priv->stations[sta_id].sta, CMD_ASYNC);
 	spin_unlock_irqrestore(&priv->sta_lock, flags);
 	return ret;
-- 
GitLab


From 6c6c51e4cc11a5456fb1172008f7c69d955af9f6 Mon Sep 17 00:00:00 2001
From: Paul Mackerras <paulus@samba.org>
Date: Mon, 3 Aug 2009 22:47:32 +1000
Subject: [PATCH 0505/1153] x86: Add quirk to make Apple MacBook5,2 use
 reboot=pci

The latest Apple MacBook (MacBook5,2) doesn't reboot successfully
under Linux; neither the EFI reboot method nor the default method
using the keyboard controller works (the system just hangs and doesn't
reset).  However, the method using the "PCI reset register" at 0xcf9
does work.

This adds a quirk to detect this machine via DMI and force the
reboot_type to BOOT_CF9.  With this it reboots successfully without
requiring a command-line option.  Note that the EFI code forces
reboot_type to BOOT_EFI when the machine is booted via EFI, but this
overrides that since the core_initcall runs after the EFI
initialization code.

Signed-off-by: Paul Mackerras <paulus@samba.org>
LKML-Reference: <19062.56420.501516.316181@cargo.ozlabs.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
---
 arch/x86/kernel/reboot.c | 34 +++++++++++++++++++++++++++++++++-
 1 file changed, 33 insertions(+), 1 deletion(-)

diff --git a/arch/x86/kernel/reboot.c b/arch/x86/kernel/reboot.c
index 508e982dd07..834c9da8bf9 100644
--- a/arch/x86/kernel/reboot.c
+++ b/arch/x86/kernel/reboot.c
@@ -3,6 +3,7 @@
 #include <linux/init.h>
 #include <linux/pm.h>
 #include <linux/efi.h>
+#include <linux/dmi.h>
 #include <acpi/reboot.h>
 #include <asm/io.h>
 #include <asm/apic.h>
@@ -17,7 +18,6 @@
 #include <asm/cpu.h>
 
 #ifdef CONFIG_X86_32
-# include <linux/dmi.h>
 # include <linux/ctype.h>
 # include <linux/mc146818rtc.h>
 #else
@@ -404,6 +404,38 @@ EXPORT_SYMBOL(machine_real_restart);
 
 #endif /* CONFIG_X86_32 */
 
+/*
+ * Apple MacBook5,2 (2009 MacBook) needs reboot=p
+ */
+static int __init set_pci_reboot(const struct dmi_system_id *d)
+{
+	if (reboot_type != BOOT_CF9) {
+		reboot_type = BOOT_CF9;
+		printk(KERN_INFO "%s series board detected. "
+		       "Selecting PCI-method for reboots.\n", d->ident);
+	}
+	return 0;
+}
+
+static struct dmi_system_id __initdata pci_reboot_dmi_table[] = {
+	{	/* Handle problems with rebooting on Apple MacBook5,2 */
+		.callback = set_pci_reboot,
+		.ident = "Apple MacBook",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MacBook5,2"),
+		},
+	},
+	{ }
+};
+
+static int __init pci_reboot_init(void)
+{
+	dmi_check_system(pci_reboot_dmi_table);
+	return 0;
+}
+core_initcall(pci_reboot_init);
+
 static inline void kb_wait(void)
 {
 	int i;
-- 
GitLab


From 6a7bbd57ed50bb62c9a81ae5f2e202ca689e5964 Mon Sep 17 00:00:00 2001
From: Paul Mackerras <paulus@samba.org>
Date: Mon, 3 Aug 2009 22:38:10 +1000
Subject: [PATCH 0506/1153] x86: Make 64-bit efi_ioremap use ioremap on MMIO
 regions

Booting current 64-bit x86 kernels on the latest Apple MacBook
(MacBook5,2) via EFI gives the following warning:

[    0.182209] ------------[ cut here ]------------
[    0.182222] WARNING: at arch/x86/mm/pageattr.c:581 __cpa_process_fault+0x44/0xa0()
[    0.182227] Hardware name: MacBook5,2
[    0.182231] CPA: called for zero pte. vaddr = ffff8800ffe00000 cpa->vaddr = ffff8800ffe00000
[    0.182236] Modules linked in:
[    0.182242] Pid: 0, comm: swapper Not tainted 2.6.31-rc4 #6
[    0.182246] Call Trace:
[    0.182254]  [<ffffffff8102c754>] ? __cpa_process_fault+0x44/0xa0
[    0.182261]  [<ffffffff81048668>] warn_slowpath_common+0x78/0xd0
[    0.182266]  [<ffffffff81048744>] warn_slowpath_fmt+0x64/0x70
[    0.182272]  [<ffffffff8102c7ec>] ? update_page_count+0x3c/0x50
[    0.182280]  [<ffffffff818d25c5>] ? phys_pmd_init+0x140/0x22e
[    0.182286]  [<ffffffff8102c754>] __cpa_process_fault+0x44/0xa0
[    0.182292]  [<ffffffff8102ce60>] __change_page_attr_set_clr+0x5f0/0xb40
[    0.182301]  [<ffffffff810d1035>] ? vm_unmap_aliases+0x175/0x190
[    0.182307]  [<ffffffff8102d4ae>] change_page_attr_set_clr+0xfe/0x3d0
[    0.182314]  [<ffffffff8102dcca>] _set_memory_uc+0x2a/0x30
[    0.182319]  [<ffffffff8102dd4b>] set_memory_uc+0x7b/0xb0
[    0.182327]  [<ffffffff818afe31>] efi_enter_virtual_mode+0x2ad/0x2c9
[    0.182334]  [<ffffffff818a1c66>] start_kernel+0x2db/0x3f4
[    0.182340]  [<ffffffff818a1289>] x86_64_start_reservations+0x99/0xb9
[    0.182345]  [<ffffffff818a1389>] x86_64_start_kernel+0xe0/0xf2
[    0.182357] ---[ end trace 4eaa2a86a8e2da22 ]---
[    0.182982] init_memory_mapping: 00000000ffffc000-0000000100000000
[    0.182993]  00ffffc000 - 0100000000 page 4k

This happens because the 64-bit version of efi_ioremap calls
init_memory_mapping for all addresses, regardless of whether they are
RAM or MMIO.  The EFI tables on this machine ask for runtime access to
some MMIO regions:

[    0.000000] EFI: mem195: type=11, attr=0x8000000000000000, range=[0x0000000093400000-0x0000000093401000) (0MB)
[    0.000000] EFI: mem196: type=11, attr=0x8000000000000000, range=[0x00000000ffc00000-0x00000000ffc40000) (0MB)
[    0.000000] EFI: mem197: type=11, attr=0x8000000000000000, range=[0x00000000ffc40000-0x00000000ffc80000) (0MB)
[    0.000000] EFI: mem198: type=11, attr=0x8000000000000000, range=[0x00000000ffc80000-0x00000000ffca4000) (0MB)
[    0.000000] EFI: mem199: type=11, attr=0x8000000000000000, range=[0x00000000ffca4000-0x00000000ffcb4000) (0MB)
[    0.000000] EFI: mem200: type=11, attr=0x8000000000000000, range=[0x00000000ffcb4000-0x00000000ffffc000) (3MB)
[    0.000000] EFI: mem201: type=11, attr=0x8000000000000000, range=[0x00000000ffffc000-0x0000000100000000) (0MB)

This arranges to pass the EFI memory type through to efi_ioremap, and
makes efi_ioremap use ioremap rather than init_memory_mapping if the
type is EFI_MEMORY_MAPPED_IO.  With this, the above warning goes away.

Signed-off-by: Paul Mackerras <paulus@samba.org>
LKML-Reference: <19062.55858.533494.471153@cargo.ozlabs.ibm.com>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
---
 arch/x86/include/asm/efi.h | 5 +++--
 arch/x86/kernel/efi.c      | 2 +-
 arch/x86/kernel/efi_64.c   | 6 +++++-
 3 files changed, 9 insertions(+), 4 deletions(-)

diff --git a/arch/x86/include/asm/efi.h b/arch/x86/include/asm/efi.h
index edc90f23e70..8406ed7f992 100644
--- a/arch/x86/include/asm/efi.h
+++ b/arch/x86/include/asm/efi.h
@@ -33,7 +33,7 @@ extern unsigned long asmlinkage efi_call_phys(void *, ...);
 #define efi_call_virt6(f, a1, a2, a3, a4, a5, a6)	\
 	efi_call_virt(f, a1, a2, a3, a4, a5, a6)
 
-#define efi_ioremap(addr, size)			ioremap_cache(addr, size)
+#define efi_ioremap(addr, size, type)		ioremap_cache(addr, size)
 
 #else /* !CONFIG_X86_32 */
 
@@ -84,7 +84,8 @@ extern u64 efi_call6(void *fp, u64 arg1, u64 arg2, u64 arg3,
 	efi_call6((void *)(efi.systab->runtime->f), (u64)(a1), (u64)(a2), \
 		  (u64)(a3), (u64)(a4), (u64)(a5), (u64)(a6))
 
-extern void __iomem *efi_ioremap(unsigned long addr, unsigned long size);
+extern void __iomem *efi_ioremap(unsigned long addr, unsigned long size,
+				 u32 type);
 
 #endif /* CONFIG_X86_32 */
 
diff --git a/arch/x86/kernel/efi.c b/arch/x86/kernel/efi.c
index 96f7ac0bbf0..19ccf6d0dcc 100644
--- a/arch/x86/kernel/efi.c
+++ b/arch/x86/kernel/efi.c
@@ -512,7 +512,7 @@ void __init efi_enter_virtual_mode(void)
 			&& end_pfn <= max_pfn_mapped))
 			va = __va(md->phys_addr);
 		else
-			va = efi_ioremap(md->phys_addr, size);
+			va = efi_ioremap(md->phys_addr, size, md->type);
 
 		md->virt_addr = (u64) (unsigned long) va;
 
diff --git a/arch/x86/kernel/efi_64.c b/arch/x86/kernel/efi_64.c
index 22c3b7828c5..ac0621a7ac3 100644
--- a/arch/x86/kernel/efi_64.c
+++ b/arch/x86/kernel/efi_64.c
@@ -98,10 +98,14 @@ void __init efi_call_phys_epilog(void)
 	early_runtime_code_mapping_set_exec(0);
 }
 
-void __iomem *__init efi_ioremap(unsigned long phys_addr, unsigned long size)
+void __iomem *__init efi_ioremap(unsigned long phys_addr, unsigned long size,
+				 u32 type)
 {
 	unsigned long last_map_pfn;
 
+	if (type == EFI_MEMORY_MAPPED_IO)
+		return ioremap(phys_addr, size);
+
 	last_map_pfn = init_memory_mapping(phys_addr, phys_addr + size);
 	if ((last_map_pfn << PAGE_SHIFT) < phys_addr + size)
 		return NULL;
-- 
GitLab


From 4486d6ede16b362f89b29845af6fe1a26ae78a54 Mon Sep 17 00:00:00 2001
From: Jeff Layton <jlayton@redhat.com>
Date: Mon, 3 Aug 2009 12:45:10 -0400
Subject: [PATCH 0507/1153] cifs: show noforceuid/noforcegid mount options (try
 #2)

Since forceuid is the default, we now need to show when it's disabled.

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
---
 fs/cifs/cifsfs.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/fs/cifs/cifsfs.c b/fs/cifs/cifsfs.c
index 44f30504b82..84b75253b05 100644
--- a/fs/cifs/cifsfs.c
+++ b/fs/cifs/cifsfs.c
@@ -376,10 +376,14 @@ cifs_show_options(struct seq_file *s, struct vfsmount *m)
 	seq_printf(s, ",uid=%d", cifs_sb->mnt_uid);
 	if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_OVERR_UID)
 		seq_printf(s, ",forceuid");
+	else
+		seq_printf(s, ",noforceuid");
 
 	seq_printf(s, ",gid=%d", cifs_sb->mnt_gid);
 	if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_OVERR_GID)
 		seq_printf(s, ",forcegid");
+	else
+		seq_printf(s, ",noforcegid");
 
 	cifs_show_address(s, tcon->ses->server);
 
-- 
GitLab


From 24e2fb615fd6b624c320cec9ea9d91a75dad902e Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Sun, 2 Aug 2009 13:00:18 +0200
Subject: [PATCH 0508/1153] cifs: Read buffer overflow

Check whether index is within bounds before testing the element.

Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
---
 fs/cifs/cifs_unicode.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/cifs/cifs_unicode.c b/fs/cifs/cifs_unicode.c
index 60e3c4253de..714a542cbaf 100644
--- a/fs/cifs/cifs_unicode.c
+++ b/fs/cifs/cifs_unicode.c
@@ -44,7 +44,7 @@ cifs_ucs2_bytes(const __le16 *from, int maxbytes,
 	int maxwords = maxbytes / 2;
 	char tmp[NLS_MAX_CHARSET_SIZE];
 
-	for (i = 0; from[i] && i < maxwords; i++) {
+	for (i = 0; i < maxwords && from[i]; i++) {
 		charlen = codepage->uni2char(le16_to_cpu(from[i]), tmp,
 					     NLS_MAX_CHARSET_SIZE);
 		if (charlen > 0)
-- 
GitLab


From d2ba8b211bb8abc29aa627dbd4dce08cfbc8082b Mon Sep 17 00:00:00 2001
From: "H. Peter Anvin" <hpa@zytor.com>
Date: Mon, 3 Aug 2009 14:44:54 -0700
Subject: [PATCH 0509/1153] x86: Fix assert syntax in vmlinux.lds.S

Older versions of binutils did not accept the naked "ASSERT" syntax;
it is considered an expression whose value needs to be assigned to
something.

Reported-tested-and-fixed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
---
 arch/x86/kernel/vmlinux.lds.S | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/x86/kernel/vmlinux.lds.S b/arch/x86/kernel/vmlinux.lds.S
index 59f31d2dd43..78d185d797d 100644
--- a/arch/x86/kernel/vmlinux.lds.S
+++ b/arch/x86/kernel/vmlinux.lds.S
@@ -393,8 +393,8 @@ SECTIONS
 
 
 #ifdef CONFIG_X86_32
-ASSERT((_end - LOAD_OFFSET <= KERNEL_IMAGE_SIZE),
-        "kernel image bigger than KERNEL_IMAGE_SIZE")
+. = ASSERT((_end - LOAD_OFFSET <= KERNEL_IMAGE_SIZE),
+	   "kernel image bigger than KERNEL_IMAGE_SIZE");
 #else
 /*
  * Per-cpu symbols which need to be offset from __per_cpu_load
@@ -407,12 +407,12 @@ INIT_PER_CPU(irq_stack_union);
 /*
  * Build-time check on the image size:
  */
-ASSERT((_end - _text <= KERNEL_IMAGE_SIZE),
-	"kernel image bigger than KERNEL_IMAGE_SIZE")
+. = ASSERT((_end - _text <= KERNEL_IMAGE_SIZE),
+	   "kernel image bigger than KERNEL_IMAGE_SIZE");
 
 #ifdef CONFIG_SMP
-ASSERT((per_cpu__irq_stack_union == 0),
-        "irq_stack_union is not at start of per-cpu area");
+. = ASSERT((per_cpu__irq_stack_union == 0),
+           "irq_stack_union is not at start of per-cpu area");
 #endif
 
 #endif /* CONFIG_X86_32 */
@@ -420,7 +420,7 @@ ASSERT((per_cpu__irq_stack_union == 0),
 #ifdef CONFIG_KEXEC
 #include <asm/kexec.h>
 
-ASSERT(kexec_control_code_size <= KEXEC_CONTROL_CODE_MAX_SIZE,
-       "kexec control code size is too big")
+. = ASSERT(kexec_control_code_size <= KEXEC_CONTROL_CODE_MAX_SIZE,
+           "kexec control code size is too big");
 #endif
 
-- 
GitLab


From bab9a3da93bfe09c609407dedae5708b07a7ac56 Mon Sep 17 00:00:00 2001
From: Borislav Petkov <borislav.petkov@amd.com>
Date: Thu, 30 Jul 2009 11:10:01 +0200
Subject: [PATCH 0510/1153] x86, msr: execute on the correct CPU subset

Make rdmsr_on_cpus/wrmsr_on_cpus execute on the current CPU only if it
is in the supplied bitmask.

Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
---
 arch/x86/lib/msr.c | 26 ++++++++++----------------
 1 file changed, 10 insertions(+), 16 deletions(-)

diff --git a/arch/x86/lib/msr.c b/arch/x86/lib/msr.c
index 1440b9c0547..caa24aca811 100644
--- a/arch/x86/lib/msr.c
+++ b/arch/x86/lib/msr.c
@@ -89,16 +89,13 @@ void rdmsr_on_cpus(const cpumask_t *mask, u32 msr_no, struct msr *msrs)
 	rv.msrs	  = msrs;
 	rv.msr_no = msr_no;
 
-	preempt_disable();
-	/*
-	 * FIXME: handle the CPU we're executing on separately for now until
-	 * smp_call_function_many has been fixed to not skip it.
-	 */
-	this_cpu = raw_smp_processor_id();
-	smp_call_function_single(this_cpu, __rdmsr_on_cpu, &rv, 1);
+	this_cpu = get_cpu();
+
+	if (cpumask_test_cpu(this_cpu, mask))
+		__rdmsr_on_cpu(&rv);
 
 	smp_call_function_many(mask, __rdmsr_on_cpu, &rv, 1);
-	preempt_enable();
+	put_cpu();
 }
 EXPORT_SYMBOL(rdmsr_on_cpus);
 
@@ -121,16 +118,13 @@ void wrmsr_on_cpus(const cpumask_t *mask, u32 msr_no, struct msr *msrs)
 	rv.msrs   = msrs;
 	rv.msr_no = msr_no;
 
-	preempt_disable();
-	/*
-	 * FIXME: handle the CPU we're executing on separately for now until
-	 * smp_call_function_many has been fixed to not skip it.
-	 */
-	this_cpu = raw_smp_processor_id();
-	smp_call_function_single(this_cpu, __wrmsr_on_cpu, &rv, 1);
+	this_cpu = get_cpu();
+
+	if (cpumask_test_cpu(this_cpu, mask))
+		__wrmsr_on_cpu(&rv);
 
 	smp_call_function_many(mask, __wrmsr_on_cpu, &rv, 1);
-	preempt_enable();
+	put_cpu();
 }
 EXPORT_SYMBOL(wrmsr_on_cpus);
 
-- 
GitLab


From f1f029c7bfbf4ee1918b90a431ab823bed812504 Mon Sep 17 00:00:00 2001
From: "H. Peter Anvin" <hpa@zytor.com>
Date: Mon, 3 Aug 2009 16:33:40 -0700
Subject: [PATCH 0511/1153] x86: fix assembly constraints in native_save_fl()

From Gabe Black in bugzilla 13888:

native_save_fl is implemented as follows:

  11static inline unsigned long native_save_fl(void)
  12{
  13        unsigned long flags;
  14
  15        asm volatile("# __raw_save_flags\n\t"
  16                     "pushf ; pop %0"
  17                     : "=g" (flags)
  18                     : /* no input */
  19                     : "memory");
  20
  21        return flags;
  22}

If gcc chooses to put flags on the stack, for instance because this is
inlined into a larger function with more register pressure, the offset
of the flags variable from the stack pointer will change when the
pushf is performed. gcc doesn't attempt to understand that fact, and
address used for pop will still be the same. It will write to
somewhere near flags on the stack but not actually into it and
overwrite some other value.

I saw this happen in the ide_device_add_all function when running in a
simulator I work on. I'm assuming that some quirk of how the simulated
hardware is set up caused the code path this is on to be executed when
it normally wouldn't.

A simple fix might be to change "=g" to "=r".

Reported-by: Gabe Black <spamforgabe@umich.edu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Stable Team <stable@kernel.org>
---
 arch/x86/include/asm/irqflags.h | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/arch/x86/include/asm/irqflags.h b/arch/x86/include/asm/irqflags.h
index 2bdab21f089..c6ccbe7e81a 100644
--- a/arch/x86/include/asm/irqflags.h
+++ b/arch/x86/include/asm/irqflags.h
@@ -12,9 +12,15 @@ static inline unsigned long native_save_fl(void)
 {
 	unsigned long flags;
 
+	/*
+	 * Note: this needs to be "=r" not "=rm", because we have the
+	 * stack offset from what gcc expects at the time the "pop" is
+	 * executed, and so a memory reference with respect to the stack
+	 * would end up using the wrong address.
+	 */
 	asm volatile("# __raw_save_flags\n\t"
 		     "pushf ; pop %0"
-		     : "=g" (flags)
+		     : "=r" (flags)
 		     : /* no input */
 		     : "memory");
 
-- 
GitLab


From f6caa14aa0b126d4a2933907d1519611b2a8524a Mon Sep 17 00:00:00 2001
From: Mike McCormack <mikem@ring3k.org>
Date: Fri, 31 Jul 2009 01:57:42 +0000
Subject: [PATCH 0512/1153] sky2: Avoid transmits during sky2_down()

This patch supersedes my previous patch "sky2: Avoid transmitting
during sky2_restart".

I have reworked the patch to avoid crashes during both sky2_restart()
and sky2_set_ringparam().

Without this patch, the sky2 driver can be crashed by doing:

# pktgen eth1 &    (transmit many packets on eth1)
# ethtool -G eth1 tx 510

I am aware you object to storing extra state, but I can't see a way
around this. Without remembering that we're restarting,
netif_wake_queue() is called in the ISR from sky2_tx_complete(), and
netif_tx_lock() is used in sky2_tx_done().  If anybody can see a way
around this, please let me know.

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/sky2.c | 14 +++++++++++++-
 drivers/net/sky2.h |  1 +
 2 files changed, 14 insertions(+), 1 deletion(-)

diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 3550c5dcd93..0a551d8f5d9 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -1488,6 +1488,8 @@ static int sky2_up(struct net_device *dev)
 	sky2_set_vlan_mode(hw, port, sky2->vlgrp != NULL);
 #endif
 
+	sky2->restarting = 0;
+
 	err = sky2_rx_start(sky2);
 	if (err)
 		goto err_out;
@@ -1500,6 +1502,9 @@ static int sky2_up(struct net_device *dev)
 
 	sky2_set_multicast(dev);
 
+	/* wake queue incase we are restarting */
+	netif_wake_queue(dev);
+
 	if (netif_msg_ifup(sky2))
 		printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
 	return 0;
@@ -1533,6 +1538,8 @@ static inline int tx_dist(unsigned tail, unsigned head)
 /* Number of list elements available for next tx */
 static inline int tx_avail(const struct sky2_port *sky2)
 {
+	if (unlikely(sky2->restarting))
+		return 0;
 	return sky2->tx_pending - tx_dist(sky2->tx_cons, sky2->tx_prod);
 }
 
@@ -1818,6 +1825,10 @@ static int sky2_down(struct net_device *dev)
 	if (netif_msg_ifdown(sky2))
 		printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
 
+	/* explicitly shut off tx incase we're restarting */
+	sky2->restarting = 1;
+	netif_tx_disable(dev);
+
 	/* Force flow control off */
 	sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
 
@@ -2359,7 +2370,7 @@ static inline void sky2_tx_done(struct net_device *dev, u16 last)
 {
 	struct sky2_port *sky2 = netdev_priv(dev);
 
-	if (netif_running(dev)) {
+	if (likely(netif_running(dev) && !sky2->restarting)) {
 		netif_tx_lock(dev);
 		sky2_tx_complete(sky2, last);
 		netif_tx_unlock(dev);
@@ -4283,6 +4294,7 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
 	spin_lock_init(&sky2->phy_lock);
 	sky2->tx_pending = TX_DEF_PENDING;
 	sky2->rx_pending = RX_DEF_PENDING;
+	sky2->restarting = 0;
 
 	hw->dev[port] = dev;
 
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index b5549c9e510..4486b066b43 100644
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -2051,6 +2051,7 @@ struct sky2_port {
 	u8		     duplex;	/* DUPLEX_HALF, DUPLEX_FULL */
 	u8		     rx_csum;
 	u8		     wol;
+	u8		     restarting;
  	enum flow_control    flow_mode;
  	enum flow_control    flow_status;
 
-- 
GitLab


From 7781de74568bddfefbd2d32a934a8c791a2420cd Mon Sep 17 00:00:00 2001
From: Jakob Bornecrantz <jakob@vmware.com>
Date: Mon, 3 Aug 2009 13:43:58 +0100
Subject: [PATCH 0513/1153] drm: Small logic fix in drm_mode_setcrtc

Match the logic to the comments in the debug message

Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/drm_crtc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c
index 8fab7890a36..33be210d672 100644
--- a/drivers/gpu/drm/drm_crtc.c
+++ b/drivers/gpu/drm/drm_crtc.c
@@ -1461,7 +1461,7 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data,
 		goto out;
 	}
 
-	if (crtc_req->count_connectors > 0 && !mode && !fb) {
+	if (crtc_req->count_connectors > 0 && (!mode || !fb)) {
 		DRM_DEBUG("Count connectors is %d but no mode or fb set\n",
 			  crtc_req->count_connectors);
 		ret = -EINVAL;
-- 
GitLab


From 4cb72b1727140f131b2df5f37c2e54f5965f98c2 Mon Sep 17 00:00:00 2001
From: Jakob Bornecrantz <jakob@vmware.com>
Date: Mon, 3 Aug 2009 13:43:59 +0100
Subject: [PATCH 0514/1153] drm: Catch stop possible NULL pointer reference

This was caught by Weiss. Also added some comments to the
fb_changed and mode_changed variables to explain what they do.

Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Tested-by: Thomas White <taw@bitwiz.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/drm_crtc_helper.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/drm_crtc_helper.c b/drivers/gpu/drm/drm_crtc_helper.c
index 3da9cfa3184..6aaa2cb2336 100644
--- a/drivers/gpu/drm/drm_crtc_helper.c
+++ b/drivers/gpu/drm/drm_crtc_helper.c
@@ -706,8 +706,8 @@ int drm_crtc_helper_set_config(struct drm_mode_set *set)
 	struct drm_encoder **save_encoders, *new_encoder;
 	struct drm_framebuffer *old_fb = NULL;
 	bool save_enabled;
-	bool mode_changed = false;
-	bool fb_changed = false;
+	bool mode_changed = false; /* if true do a full mode set */
+	bool fb_changed = false; /* if true and !mode_changed just do a flip */
 	struct drm_connector *connector;
 	int count = 0, ro, fail = 0;
 	struct drm_crtc_helper_funcs *crtc_funcs;
@@ -758,6 +758,8 @@ int drm_crtc_helper_set_config(struct drm_mode_set *set)
 		if (set->crtc->fb == NULL) {
 			DRM_DEBUG("crtc has no fb, full mode set\n");
 			mode_changed = true;
+		} else if (set->fb == NULL) {
+			mode_changed = true;
 		} else if ((set->fb->bits_per_pixel !=
 			 set->crtc->fb->bits_per_pixel) ||
 			 set->fb->depth != set->crtc->fb->depth)
-- 
GitLab


From 7320700df1864b601cef5adbddce8654a0e3f78b Mon Sep 17 00:00:00 2001
From: Alex Deucher <alexdeucher@gmail.com>
Date: Mon, 3 Aug 2009 17:01:53 -0400
Subject: [PATCH 0515/1153] drm/radeon: add some new r7xx pci ids

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 include/drm/drm_pciids.h | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/include/drm/drm_pciids.h b/include/drm/drm_pciids.h
index 7174818c2c1..9d4c0049154 100644
--- a/include/drm/drm_pciids.h
+++ b/include/drm/drm_pciids.h
@@ -257,9 +257,12 @@
 	{0x1002, 0x940F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_R600|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x94A0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x94A1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
+	{0x1002, 0x94A3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x94B1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x94B3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_NEW_MEMMAP}, \
+	{0x1002, 0x94B4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x94B5, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_NEW_MEMMAP}, \
+	{0x1002, 0x94B9, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV740|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9440, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV770|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9441, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV770|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9442, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV770|RADEON_NEW_MEMMAP}, \
@@ -288,6 +291,7 @@
 	{0x1002, 0x948F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9490, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9491, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
+	{0x1002, 0x9495, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9498, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x949C, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x949E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV730|RADEON_NEW_MEMMAP}, \
@@ -325,6 +329,7 @@
 	{0x1002, 0x9552, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV710|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9553, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV710|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9555, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV710|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
+	{0x1002, 0x9557, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV710|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9580, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV630|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9581, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV630|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
 	{0x1002, 0x9583, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RV630|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
-- 
GitLab


From 0924d942256ac470c5f7b4ebaf7fe0415fc6fa59 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Mon, 3 Aug 2009 12:03:03 +1000
Subject: [PATCH 0516/1153] drm/radeon/kms: fix rv515 VRAM initialisation.

This got missed in the VRAM init re-workings.

Signed-of-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/rv515.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c
index 551e608702e..fd8f3ca716e 100644
--- a/drivers/gpu/drm/radeon/rv515.c
+++ b/drivers/gpu/drm/radeon/rv515.c
@@ -370,6 +370,7 @@ void rv515_vram_info(struct radeon_device *rdev)
 
 	rv515_vram_get_type(rdev);
 
+	r100_vram_init_sizes(rdev);
 	/* FIXME: we should enforce default clock in case GPU is not in
 	 * default setup
 	 */
-- 
GitLab


From 6d0897ba58139523d37e97855ee0fe2d78629da6 Mon Sep 17 00:00:00 2001
From: Thomas Hellstrom <thellstrom@vmware.com>
Date: Fri, 31 Jul 2009 10:47:51 +0200
Subject: [PATCH 0517/1153] drm/ttm: Fix a potential comparison of structs.

On some architectures the comparison may cause a compilation failure.

Original partial fix Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>

Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/ttm/ttm_bo_util.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/ttm/ttm_bo_util.c b/drivers/gpu/drm/ttm/ttm_bo_util.c
index ce2e6f38ea0..ad4ada07c6c 100644
--- a/drivers/gpu/drm/ttm/ttm_bo_util.c
+++ b/drivers/gpu/drm/ttm/ttm_bo_util.c
@@ -150,7 +150,7 @@ static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src,
 #ifdef CONFIG_X86
 	dst = kmap_atomic_prot(d, KM_USER0, prot);
 #else
-	if (prot != PAGE_KERNEL)
+	if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL))
 		dst = vmap(&d, 1, 0, prot);
 	else
 		dst = kmap(d);
@@ -163,7 +163,7 @@ static int ttm_copy_io_ttm_page(struct ttm_tt *ttm, void *src,
 #ifdef CONFIG_X86
 	kunmap_atomic(dst, KM_USER0);
 #else
-	if (prot != PAGE_KERNEL)
+	if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL))
 		vunmap(dst);
 	else
 		kunmap(d);
@@ -186,7 +186,7 @@ static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst,
 #ifdef CONFIG_X86
 	src = kmap_atomic_prot(s, KM_USER0, prot);
 #else
-	if (prot != PAGE_KERNEL)
+	if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL))
 		src = vmap(&s, 1, 0, prot);
 	else
 		src = kmap(s);
@@ -199,7 +199,7 @@ static int ttm_copy_ttm_io_page(struct ttm_tt *ttm, void *dst,
 #ifdef CONFIG_X86
 	kunmap_atomic(src, KM_USER0);
 #else
-	if (prot != PAGE_KERNEL)
+	if (pgprot_val(prot) != pgprot_val(PAGE_KERNEL))
 		vunmap(src);
 	else
 		kunmap(s);
-- 
GitLab


From de05065ff5d6878523317ff4a0b48a1239f80f73 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Mon, 3 Aug 2009 12:05:34 +1000
Subject: [PATCH 0518/1153] drm/radeon/kms: fix nomodeset.

The ordering was wrong to get the nomodeset parameter to work.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_drv.c | 17 ++++++++---------
 1 file changed, 8 insertions(+), 9 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_drv.c b/drivers/gpu/drm/radeon/radeon_drv.c
index 3cfcee17dc5..0bd5879a495 100644
--- a/drivers/gpu/drm/radeon/radeon_drv.c
+++ b/drivers/gpu/drm/radeon/radeon_drv.c
@@ -318,6 +318,14 @@ static int __init radeon_init(void)
 	driver = &driver_old;
 	driver->num_ioctls = radeon_max_ioctl;
 #if defined(CONFIG_DRM_RADEON_KMS)
+#ifdef CONFIG_VGA_CONSOLE
+	if (vgacon_text_force() && radeon_modeset == -1) {
+		DRM_INFO("VGACON disable radeon kernel modesetting.\n");
+		driver = &driver_old;
+		driver->driver_features &= ~DRIVER_MODESET;
+		radeon_modeset = 0;
+	}
+#endif
 	/* if enabled by default */
 	if (radeon_modeset == -1) {
 		DRM_INFO("radeon default to kernel modesetting.\n");
@@ -329,17 +337,8 @@ static int __init radeon_init(void)
 		driver->driver_features |= DRIVER_MODESET;
 		driver->num_ioctls = radeon_max_kms_ioctl;
 	}
-
 	/* if the vga console setting is enabled still
 	 * let modprobe override it */
-#ifdef CONFIG_VGA_CONSOLE
-	if (vgacon_text_force() && radeon_modeset == -1) {
-		DRM_INFO("VGACON disable radeon kernel modesetting.\n");
-		driver = &driver_old;
-		driver->driver_features &= ~DRIVER_MODESET;
-		radeon_modeset = 0;
-	}
-#endif
 #endif
 	return drm_init(driver);
 }
-- 
GitLab


From c9b7fb54f0a51e587fa09be3a85666b43d36a850 Mon Sep 17 00:00:00 2001
From: Xiaotian Feng <dfeng@redhat.com>
Date: Wed, 29 Jul 2009 21:28:24 +0800
Subject: [PATCH 0519/1153] drm/radeon/kms: fix memory leak in
 radeon_driver_load_kms

This patch fixes following kmemleak report:
unreferenced object 0xffff88022cb53000 (size 4096):
  comm "work_for_cpu", pid 97, jiffies 4294672345
  backtrace:
    [<ffffffff810eb222>] create_object+0x19f/0x2a0
    [<ffffffff810eb422>] kmemleak_alloc+0x26/0x4c
    [<ffffffff810e363f>] __kmalloc+0x187/0x1b0
    [<ffffffffa005f3db>] kzalloc.clone.0+0x13/0x15 [radeon]
    [<ffffffffa005f403>] radeon_driver_load_kms+0x26/0xe1 [radeon]
    [<ffffffffa0017432>] drm_get_dev+0x37f/0x480 [drm]
    [<ffffffffa007f424>] radeon_pci_probe+0x15/0x269 [radeon]
    [<ffffffff811f8779>] local_pci_probe+0x17/0x1b
    [<ffffffff8105ffbb>] do_work_for_cpu+0x18/0x2a
    [<ffffffff81063c38>] kthread+0x8a/0x92
    [<ffffffff81012cba>] child_rip+0xa/0x20
    [<ffffffffffffffff>] 0xffffffffffffffff

Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_kms.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c
index 937a2f1cdb4..3357110e30c 100644
--- a/drivers/gpu/drm/radeon/radeon_kms.c
+++ b/drivers/gpu/drm/radeon/radeon_kms.c
@@ -58,6 +58,8 @@ int radeon_driver_load_kms(struct drm_device *dev, unsigned long flags)
 	if (r) {
 		DRM_ERROR("Failed to initialize radeon, disabling IOCTL\n");
 		radeon_device_fini(rdev);
+		kfree(rdev);
+		dev->dev_private = NULL;
 		return r;
 	}
 	return 0;
-- 
GitLab


From fee280d3fd9bc5247bef9f4ab35a4693bfffdcfd Mon Sep 17 00:00:00 2001
From: Thomas Hellstrom <thellstrom@vmware.com>
Date: Mon, 3 Aug 2009 12:39:06 +0200
Subject: [PATCH 0520/1153] drm/ttm: Fix a sync object leak.

If there are multiple simultaneous waiters for the same buffer object,
a temporary reference to its sync object may be leaked.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/ttm/ttm_bo.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c
index 6538d423698..aa82d5370c3 100644
--- a/drivers/gpu/drm/ttm/ttm_bo.c
+++ b/drivers/gpu/drm/ttm/ttm_bo.c
@@ -1575,6 +1575,10 @@ int ttm_bo_wait(struct ttm_buffer_object *bo,
 			driver->sync_obj_unref(&sync_obj);
 			driver->sync_obj_unref(&tmp_obj);
 			spin_lock(&bo->lock);
+		} else {
+			spin_unlock(&bo->lock);
+			driver->sync_obj_unref(&sync_obj);
+			spin_lock(&bo->lock);
 		}
 	}
 	return 0;
-- 
GitLab


From fa99239cb73dbf419bea9f334b85ba94ac88a532 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Mon, 3 Aug 2009 14:20:32 +0200
Subject: [PATCH 0521/1153] drm/radeon: Read buffer overflow

Check whether index is within bounds before grabbing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r100.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index 05a44896dff..f1ba8ff4113 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -722,13 +722,14 @@ int r100_cs_packet_parse(struct radeon_cs_parser *p,
 			 unsigned idx)
 {
 	struct radeon_cs_chunk *ib_chunk = &p->chunks[p->chunk_ib_idx];
-	uint32_t header = ib_chunk->kdata[idx];
+	uint32_t header;
 
 	if (idx >= ib_chunk->length_dw) {
 		DRM_ERROR("Can not parse packet at %d after CS end %d !\n",
 			  idx, ib_chunk->length_dw);
 		return -EINVAL;
 	}
+	header = ib_chunk->kdata[idx];
 	pkt->idx = idx;
 	pkt->type = CP_PACKET_GET_TYPE(header);
 	pkt->count = CP_PACKET_GET_COUNT(header);
-- 
GitLab


From c96e7c7a3a79931446ecf9494a8415e4d164ebd8 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Mon, 3 Aug 2009 14:22:53 +0200
Subject: [PATCH 0522/1153] drm/ttm: Read buffer overflow

Check whether index is within bounds before grabbing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/ttm/ttm_bo.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c
index aa82d5370c3..c2b0d710d10 100644
--- a/drivers/gpu/drm/ttm/ttm_bo.c
+++ b/drivers/gpu/drm/ttm/ttm_bo.c
@@ -1182,13 +1182,14 @@ static int ttm_bo_force_list_clean(struct ttm_bo_device *bdev,
 
 int ttm_bo_clean_mm(struct ttm_bo_device *bdev, unsigned mem_type)
 {
-	struct ttm_mem_type_manager *man = &bdev->man[mem_type];
+	struct ttm_mem_type_manager *man;
 	int ret = -EINVAL;
 
 	if (mem_type >= TTM_NUM_MEM_TYPES) {
 		printk(KERN_ERR TTM_PFX "Illegal memory type %d\n", mem_type);
 		return ret;
 	}
+	man = &bdev->man[mem_type];
 
 	if (!man->has_type) {
 		printk(KERN_ERR TTM_PFX "Trying to take down uninitialized "
-- 
GitLab


From d098564f3b2b5d555e51bca765a6a9e0dda8f2cd Mon Sep 17 00:00:00 2001
From: Steve French <sfrench@us.ibm.com>
Date: Tue, 4 Aug 2009 03:53:28 +0000
Subject: [PATCH 0523/1153] [CIFS] Update readme to reflect forceuid mount
 parms

Signed-off-by: Steve French <sfrench@us.ibm.com>
---
 fs/cifs/CHANGES |  3 ++-
 fs/cifs/README  | 25 ++++++++++++-------------
 2 files changed, 14 insertions(+), 14 deletions(-)

diff --git a/fs/cifs/CHANGES b/fs/cifs/CHANGES
index 651cefde385..e85b1e4389e 100644
--- a/fs/cifs/CHANGES
+++ b/fs/cifs/CHANGES
@@ -2,7 +2,8 @@ Version 1.60
 -------------
 Fix memory leak in reconnect.  Fix oops in DFS mount error path.
 Set s_maxbytes to smaller (the max that vfs can handle) so that
-sendfile will now work over cifs mounts again.
+sendfile will now work over cifs mounts again.  Add noforcegid
+and noforceuid mount parameters.
 
 Version 1.59
 ------------
diff --git a/fs/cifs/README b/fs/cifs/README
index ad92921dbde..79c1a93400b 100644
--- a/fs/cifs/README
+++ b/fs/cifs/README
@@ -262,11 +262,11 @@ A partial list of the supported mount options follows:
 		mount.	
   domain	Set the SMB/CIFS workgroup name prepended to the
 		username during CIFS session establishment
-  forceuid	Set the default uid for inodes based on the uid
-		passed in. For mounts to servers
+  forceuid	Set the default uid for inodes to the uid
+		passed in on mount. For mounts to servers
 		which do support the CIFS Unix extensions, such as a
 		properly configured Samba server, the server provides
-		the uid, gid and mode so this parameter should  not be
+		the uid, gid and mode so this parameter should not be
 		specified unless the server and clients uid and gid
 		numbering differ.  If the server and client are in the
 		same domain (e.g. running winbind or nss_ldap) and
@@ -278,11 +278,7 @@ A partial list of the supported mount options follows:
 		of existing files will be the uid (gid) of the person
 		who executed the mount (root, except when mount.cifs
 		is configured setuid for user mounts) unless the "uid=" 
-		(gid) mount option is specified.  For the uid (gid) of newly
-		created files and directories, ie files created since 
-		the last mount of the server share, the expected uid 
-		(gid) is cached as long as the inode remains in 
-		memory on the client.   Also note that permission
+		(gid) mount option is specified. Also note that permission
 		checks (authorization checks) on accesses to a file occur
 		at the server, but there are cases in which an administrator
 		may want to restrict at the client as well.  For those
@@ -290,12 +286,15 @@ A partial list of the supported mount options follows:
 		(such as Windows), permissions can also be checked at the
 		client, and a crude form of client side permission checking 
 		can be enabled by specifying file_mode and dir_mode on 
-		the client.  Note that the mount.cifs helper must be
-		at version 1.10 or higher to support specifying the uid
-		(or gid) in non-numeric form.
-  forcegid	(similar to above but for the groupid instead of uid)
+		the client.  (default)
+  forcegid	(similar to above but for the groupid instead of uid) (default)
+  noforceuid	Fill in file owner information (uid) by requesting it from
+		the server if possible. With this option, the value given in
+		the uid= option (on mount) will only be used if the server
+		can not support returning uids on inodes.
+  noforcegid	(similar to above but for the group owner, gid, instead of uid)
   uid		Set the default uid for inodes, and indicate to the
-		cifs kernel driver which local user mounted . If the server
+		cifs kernel driver which local user mounted. If the server
 		supports the unix extensions the default uid is
 		not used to fill in the owner fields of inodes (files)
 		unless the "forceuid" parameter is specified.
-- 
GitLab


From 0cb13536c3382004bd9b833565e2af33f26ed1fb Mon Sep 17 00:00:00 2001
From: Jean Delvare <khali@linux-fr.org>
Date: Mon, 3 Aug 2009 21:10:01 -0700
Subject: [PATCH 0524/1153] 3c59x: Fix build failure with gcc 3.2

Fix the following build failure with gcc 3.2:

  CC [M]  drivers/net/3c59x.o
drivers/net/3c59x.c:2726:1: directives may not be used inside a macro argument
drivers/net/3c59x.c:2725:59: unterminated argument list invoking macro "pr_err"
drivers/net/3c59x.c: In function `dump_tx_ring':
drivers/net/3c59x.c:2727: implicit declaration of function `pr_err'
drivers/net/3c59x.c:2731: syntax error before ')' token

Apparently gcc 3.2 doesn't like #if interleaved with a macro call.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/3c59x.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)

diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c
index c34aee91250..c2041685094 100644
--- a/drivers/net/3c59x.c
+++ b/drivers/net/3c59x.c
@@ -2721,13 +2721,15 @@ dump_tx_ring(struct net_device *dev)
 				   &vp->tx_ring[vp->dirty_tx % TX_RING_SIZE]);
 			issue_and_wait(dev, DownStall);
 			for (i = 0; i < TX_RING_SIZE; i++) {
-				pr_err("  %d: @%p  length %8.8x status %8.8x\n", i,
-					   &vp->tx_ring[i],
+				unsigned int length;
+
 #if DO_ZEROCOPY
-					   le32_to_cpu(vp->tx_ring[i].frag[0].length),
+				length = le32_to_cpu(vp->tx_ring[i].frag[0].length);
 #else
-					   le32_to_cpu(vp->tx_ring[i].length),
+				length = le32_to_cpu(vp->tx_ring[i].length);
 #endif
+				pr_err("  %d: @%p  length %8.8x status %8.8x\n",
+					   i, &vp->tx_ring[i], length,
 					   le32_to_cpu(vp->tx_ring[i].status));
 			}
 			if (!stalled)
-- 
GitLab


From 70d715fd0597f18528f389b5ac59102263067744 Mon Sep 17 00:00:00 2001
From: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Date: Mon, 3 Aug 2009 11:48:19 +0900
Subject: [PATCH 0525/1153] posix-timers: Fix oops in clock_nanosleep() with
 CLOCK_MONOTONIC_RAW

Prevent calling do_nanosleep() with clockid
CLOCK_MONOTONIC_RAW, it may cause oops, such as NULL pointer
dereference.

Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: <stable@kernel.org>
LKML-Reference: <4A764FF3.50607@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/posix-timers.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/kernel/posix-timers.c b/kernel/posix-timers.c
index 052ec4d195c..d089d052c4a 100644
--- a/kernel/posix-timers.c
+++ b/kernel/posix-timers.c
@@ -202,6 +202,12 @@ static int no_timer_create(struct k_itimer *new_timer)
 	return -EOPNOTSUPP;
 }
 
+static int no_nsleep(const clockid_t which_clock, int flags,
+		     struct timespec *tsave, struct timespec __user *rmtp)
+{
+	return -EOPNOTSUPP;
+}
+
 /*
  * Return nonzero if we know a priori this clockid_t value is bogus.
  */
@@ -254,6 +260,7 @@ static __init int init_posix_timers(void)
 		.clock_get = posix_get_monotonic_raw,
 		.clock_set = do_posix_clock_nosettime,
 		.timer_create = no_timer_create,
+		.nsleep = no_nsleep,
 	};
 
 	register_posix_clock(CLOCK_REALTIME, &clock_realtime);
-- 
GitLab


From 7e030655dda5b5efc4305e2a8f46c4967d32eb3d Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Sun, 2 Aug 2009 13:43:11 +0200
Subject: [PATCH 0526/1153] perf: Fix read buffer overflow

Check whether index is within bounds before testing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: a.p.zijlstra@chello.nl
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A757BCF.40101@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-report.c | 2 +-
 tools/perf/util/quote.c     | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index 95fd06cdaa9..ce4f28645e6 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -253,7 +253,7 @@ static int strcommon(const char *pathname)
 {
 	int n = 0;
 
-	while (pathname[n] == cwd[n] && n < cwdlen)
+	while (n < cwdlen && pathname[n] == cwd[n])
 		++n;
 
 	return n;
diff --git a/tools/perf/util/quote.c b/tools/perf/util/quote.c
index c6e5dc0dc82..2726fe40eb5 100644
--- a/tools/perf/util/quote.c
+++ b/tools/perf/util/quote.c
@@ -318,7 +318,7 @@ char *quote_path_relative(const char *in, int len,
 		strbuf_addch(out, '"');
 	if (prefix) {
 		int off = 0;
-		while (prefix[off] && off < len && prefix[off] == in[off])
+		while (off < len && prefix[off] && prefix[off] == in[off])
 			if (prefix[off] == '/') {
 				prefix += off + 1;
 				in += off + 1;
-- 
GitLab


From c2718348b41a8e7646516d9af8bb0231c6a44374 Mon Sep 17 00:00:00 2001
From: Doug Thompson <dougthompson@xmission.com>
Date: Tue, 4 Aug 2009 12:02:20 +0200
Subject: [PATCH 0527/1153] amd64_edac: print debug statements only on error

Add forgotten return calls for the successful cases.

Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
---
 drivers/edac/amd64_edac.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/edac/amd64_edac.c b/drivers/edac/amd64_edac.c
index 5fa924d61b1..e2a10bcba7a 100644
--- a/drivers/edac/amd64_edac.c
+++ b/drivers/edac/amd64_edac.c
@@ -868,6 +868,8 @@ static void amd64_read_dbam_reg(struct amd64_pvt *pvt)
 			goto err_reg;
 	}
 
+	return;
+
 err_reg:
 	debugf0("Error reading F2x%03x.\n", reg);
 }
@@ -2634,6 +2636,8 @@ static void amd64_read_mc_registers(struct amd64_pvt *pvt)
 
 	amd64_dump_misc_regs(pvt);
 
+	return;
+
 err_reg:
 	debugf0("Reading an MC register failed\n");
 
-- 
GitLab


From 57ca7deb062abf56168d15f000c16e25f88a9cf3 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Anders=20Grafstr=C3=B6m?= <grfstrm@users.sourceforge.net>
Date: Tue, 4 Aug 2009 13:11:47 +0200
Subject: [PATCH 0528/1153] jffs2: Fix return value from
 jffs2_do_readpage_nolock()
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

This fixes "kernel BUG at fs/jffs2/file.c:251!".
This pseudocode hopefully illustrates the scenario that triggers it:

jffs2_write_begin {
     jffs2_do_readpage_nolock {
         jffs2_read_inode_range {
             jffs2_read_dnode {
                 Data CRC 33c102e9 != calculated CRC 0ef77e7b for node at 005d42e4
                 return -EIO;
             }
         }
         ClearPageUptodate(pg);
         return 0;
     }
}

jffs2_write_end {
     BUG_ON(!PageUptodate(pg));
}

Signed-off-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 fs/jffs2/file.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/jffs2/file.c b/fs/jffs2/file.c
index 5edc2bf2058..23c94753986 100644
--- a/fs/jffs2/file.c
+++ b/fs/jffs2/file.c
@@ -99,7 +99,7 @@ static int jffs2_do_readpage_nolock (struct inode *inode, struct page *pg)
 	kunmap(pg);
 
 	D2(printk(KERN_DEBUG "readpage finished\n"));
-	return 0;
+	return ret;
 }
 
 int jffs2_do_readpage_unlock(struct inode *inode, struct page *pg)
-- 
GitLab


From 6c7184b77464261b7d55583a48accbd1350923a3 Mon Sep 17 00:00:00 2001
From: Jack Steiner <steiner@sgi.com>
Date: Mon, 27 Jul 2009 09:35:07 -0500
Subject: [PATCH 0529/1153] x86, UV: Handle missing blade-local memory
 correctly

UV blades may not have any blade-local memory. Add a field
(nid) to the UV blade structure to indicates whether the node
has local memory. This is needed by the GRU driver (pushed
separately).

Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
LKML-Reference: <20090727143507.GA7006@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/include/asm/uv/uv_hub.h   | 7 +++++++
 arch/x86/kernel/apic/x2apic_uv_x.c | 5 +++++
 2 files changed, 12 insertions(+)

diff --git a/arch/x86/include/asm/uv/uv_hub.h b/arch/x86/include/asm/uv/uv_hub.h
index 341070f7ad5..a6dde059e02 100644
--- a/arch/x86/include/asm/uv/uv_hub.h
+++ b/arch/x86/include/asm/uv/uv_hub.h
@@ -327,6 +327,7 @@ struct uv_blade_info {
 	unsigned short	nr_possible_cpus;
 	unsigned short	nr_online_cpus;
 	unsigned short	pnode;
+	short		memory_nid;
 };
 extern struct uv_blade_info *uv_blade_info;
 extern short *uv_node_to_blade;
@@ -363,6 +364,12 @@ static inline int uv_blade_to_pnode(int bid)
 	return uv_blade_info[bid].pnode;
 }
 
+/* Nid of memory node on blade. -1 if no blade-local memory */
+static inline int uv_blade_to_memory_nid(int bid)
+{
+	return uv_blade_info[bid].memory_nid;
+}
+
 /* Determine the number of possible cpus on a blade */
 static inline int uv_blade_nr_possible_cpus(int bid)
 {
diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c
index 096d19aea2f..ad3f0a984ca 100644
--- a/arch/x86/kernel/apic/x2apic_uv_x.c
+++ b/arch/x86/kernel/apic/x2apic_uv_x.c
@@ -591,6 +591,8 @@ void __init uv_system_init(void)
 	bytes = sizeof(struct uv_blade_info) * uv_num_possible_blades();
 	uv_blade_info = kmalloc(bytes, GFP_KERNEL);
 	BUG_ON(!uv_blade_info);
+	for (blade = 0; blade < uv_num_possible_blades(); blade++)
+		uv_blade_info[blade].memory_nid = -1;
 
 	get_lowmem_redirect(&lowmem_redir_base, &lowmem_redir_size);
 
@@ -629,6 +631,9 @@ void __init uv_system_init(void)
 		lcpu = uv_blade_info[blade].nr_possible_cpus;
 		uv_blade_info[blade].nr_possible_cpus++;
 
+		/* Any node on the blade, else will contain -1. */
+		uv_blade_info[blade].memory_nid = nid;
+
 		uv_cpu_hub_info(cpu)->lowmem_remap_base = lowmem_redir_base;
 		uv_cpu_hub_info(cpu)->lowmem_remap_top = lowmem_redir_size;
 		uv_cpu_hub_info(cpu)->m_val = m_val;
-- 
GitLab


From cc5e4fa1bd4d2f56da07f9092281afdcd2374ab9 Mon Sep 17 00:00:00 2001
From: Jack Steiner <steiner@sgi.com>
Date: Mon, 27 Jul 2009 09:36:56 -0500
Subject: [PATCH 0530/1153] x86, UV: Delete mapping of MMR rangs mapped by BIOS

The UV BIOS has added additional MMR ranges that are mapped via
EFI virtual mode mappings. These ranges should be deleted from
ranges mapped by uv_system_init().

Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
LKML-Reference: <20090727143656.GA7698@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/apic/x2apic_uv_x.c | 31 +-----------------------------
 1 file changed, 1 insertion(+), 30 deletions(-)

diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c
index ad3f0a984ca..445c210daf8 100644
--- a/arch/x86/kernel/apic/x2apic_uv_x.c
+++ b/arch/x86/kernel/apic/x2apic_uv_x.c
@@ -362,12 +362,6 @@ static __init void get_lowmem_redirect(unsigned long *base, unsigned long *size)
 	BUG();
 }
 
-static __init void map_low_mmrs(void)
-{
-	init_extra_mapping_uc(UV_GLOBAL_MMR32_BASE, UV_GLOBAL_MMR32_SIZE);
-	init_extra_mapping_uc(UV_LOCAL_MMR_BASE, UV_LOCAL_MMR_SIZE);
-}
-
 enum map_type {map_wb, map_uc};
 
 static __init void map_high(char *id, unsigned long base, int shift,
@@ -395,26 +389,6 @@ static __init void map_gru_high(int max_pnode)
 		map_high("GRU", gru.s.base, shift, max_pnode, map_wb);
 }
 
-static __init void map_config_high(int max_pnode)
-{
-	union uvh_rh_gam_cfg_overlay_config_mmr_u cfg;
-	int shift = UVH_RH_GAM_CFG_OVERLAY_CONFIG_MMR_BASE_SHFT;
-
-	cfg.v = uv_read_local_mmr(UVH_RH_GAM_CFG_OVERLAY_CONFIG_MMR);
-	if (cfg.s.enable)
-		map_high("CONFIG", cfg.s.base, shift, max_pnode, map_uc);
-}
-
-static __init void map_mmr_high(int max_pnode)
-{
-	union uvh_rh_gam_mmr_overlay_config_mmr_u mmr;
-	int shift = UVH_RH_GAM_MMR_OVERLAY_CONFIG_MMR_BASE_SHFT;
-
-	mmr.v = uv_read_local_mmr(UVH_RH_GAM_MMR_OVERLAY_CONFIG_MMR);
-	if (mmr.s.enable)
-		map_high("MMR", mmr.s.base, shift, max_pnode, map_uc);
-}
-
 static __init void map_mmioh_high(int max_pnode)
 {
 	union uvh_rh_gam_mmioh_overlay_config_mmr_u mmioh;
@@ -566,8 +540,6 @@ void __init uv_system_init(void)
 	unsigned long mmr_base, present, paddr;
 	unsigned short pnode_mask;
 
-	map_low_mmrs();
-
 	m_n_config.v = uv_read_local_mmr(UVH_SI_ADDR_MAP_CONFIG);
 	m_val = m_n_config.s.m_skt;
 	n_val = m_n_config.s.n_skt;
@@ -667,11 +639,10 @@ void __init uv_system_init(void)
 		pnode = (paddr >> m_val) & pnode_mask;
 		blade = boot_pnode_to_blade(pnode);
 		uv_node_to_blade[nid] = blade;
+		max_pnode = max(pnode, max_pnode);
 	}
 
 	map_gru_high(max_pnode);
-	map_mmr_high(max_pnode);
-	map_config_high(max_pnode);
 	map_mmioh_high(max_pnode);
 
 	uv_cpu_init();
-- 
GitLab


From 67e83f309ed0baaf01a2c956b5174905bcdc1242 Mon Sep 17 00:00:00 2001
From: Jack Steiner <steiner@sgi.com>
Date: Mon, 27 Jul 2009 09:38:08 -0500
Subject: [PATCH 0531/1153] x86, UV: Fix macros for accessing large node
 numbers

The UV chipset automatically supplies the upper bits on nodes
being referenced by MMR accesses. These bit can be deleted from
the hub addressing macros.

Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090727143808.GA8076@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/include/asm/uv/uv_hub.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/include/asm/uv/uv_hub.h b/arch/x86/include/asm/uv/uv_hub.h
index a6dde059e02..77a68505419 100644
--- a/arch/x86/include/asm/uv/uv_hub.h
+++ b/arch/x86/include/asm/uv/uv_hub.h
@@ -175,7 +175,7 @@ DECLARE_PER_CPU(struct uv_hub_info_s, __uv_hub_info);
 #define UV_GLOBAL_MMR32_PNODE_BITS(p)	((p) << (UV_GLOBAL_MMR32_PNODE_SHIFT))
 
 #define UV_GLOBAL_MMR64_PNODE_BITS(p)					\
-	((unsigned long)(UV_PNODE_TO_GNODE(p)) << UV_GLOBAL_MMR64_PNODE_SHIFT)
+	(((unsigned long)(p)) << UV_GLOBAL_MMR64_PNODE_SHIFT)
 
 #define UV_APIC_PNODE_SHIFT	6
 
-- 
GitLab


From c5997fa8d7aca3c9876a6ff71bacf27c41095ce9 Mon Sep 17 00:00:00 2001
From: Jack Steiner <steiner@sgi.com>
Date: Mon, 27 Jul 2009 09:38:56 -0500
Subject: [PATCH 0532/1153] x86, UV: Fix UV apic mode

Change SGI UV default apicid mode to "physical". This is
required to match settings in the UV hub chip.

Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090727143856.GA8905@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/apic/x2apic_uv_x.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c
index 445c210daf8..832e908adcb 100644
--- a/arch/x86/kernel/apic/x2apic_uv_x.c
+++ b/arch/x86/kernel/apic/x2apic_uv_x.c
@@ -261,7 +261,7 @@ struct apic apic_x2apic_uv_x = {
 	.apic_id_registered		= uv_apic_id_registered,
 
 	.irq_delivery_mode		= dest_Fixed,
-	.irq_dest_mode			= 1, /* logical */
+	.irq_dest_mode			= 0, /* physical */
 
 	.target_cpus			= uv_target_cpus,
 	.disable_esr			= 0,
-- 
GitLab


From d8c7eb34c2db6268909ae8c3958be63bde254292 Mon Sep 17 00:00:00 2001
From: Yinghai Lu <yinghai@kernel.org>
Date: Sat, 25 Jul 2009 03:23:09 -0700
Subject: [PATCH 0533/1153] x86: Don't use current_cpu_data in x2apic
 phys_pkg_id

One system has socket 1 come up as BSP.

kexeced kernel reports BSP as:

[    1.524550] Initializing cgroup subsys cpuacct
[    1.536064] initial_apicid:20
[    1.537135] ht_mask_width:1
[    1.538128] core_select_mask:f
[    1.539126] core_plus_mask_width:5
[    1.558479] CPU: Physical Processor ID: 0
[    1.559501] CPU: Processor Core ID: 0
[    1.560539] CPU: L1 I cache: 32K, L1 D cache: 32K
[    1.579098] CPU: L2 cache: 256K
[    1.580085] CPU: L3 cache: 24576K
[    1.581108] CPU 0/0x20 -> Node 0
[    1.596193] CPU 0 microcode level: 0xffff0008

It doesn't have correct physical processor id and will get an
error:

[   38.840859] CPU0 attaching sched-domain:
[   38.848287]  domain 0: span 0,8,72 level SIBLING
[   38.851151]   groups: 0 8 72
[   38.858137]   domain 1: span 0,8-15,72-79 level MC
[   38.868944]    groups: 0,8,72 9,73 10,74 11,75 12,76 13,77 14,78 15,79
[   38.881383] ERROR: parent span is not a superset of domain->span
[   38.890724]    domain 2: span 0-7,64-71 level CPU
[   38.899237] ERROR: domain->groups does not contain CPU0
[   38.909229]     groups: 8-15,72-79
[   38.912547] ERROR: groups don't span domain->span
[   38.919665]     domain 3: span 0-127 level NODE
[   38.930739]      groups: 0-7,64-71 8-15,72-79 16-23,80-87 24-31,88-95 32-39,96-103 40-47,104-111 48-55,112-119 56-63,120-127

it turns out: we can not use current_cpu_data in phys_pgd_id
for x2apic.

identify_boot_cpu() is called by check_bugs() before
smp_prepare_cpus() and till smp_prepare_cpus() current_cpu_data
for bsp is assigned with boot_cpu_data.

Just make phys_pkg_id for x2apic is aligned to xapic.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A6ADD0D.10002@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/apic/x2apic_cluster.c | 2 +-
 arch/x86/kernel/apic/x2apic_phys.c    | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kernel/apic/x2apic_cluster.c b/arch/x86/kernel/apic/x2apic_cluster.c
index 8e4cbb255c3..2ed4e2bb3b3 100644
--- a/arch/x86/kernel/apic/x2apic_cluster.c
+++ b/arch/x86/kernel/apic/x2apic_cluster.c
@@ -170,7 +170,7 @@ static unsigned long set_apic_id(unsigned int id)
 
 static int x2apic_cluster_phys_pkg_id(int initial_apicid, int index_msb)
 {
-	return current_cpu_data.initial_apicid >> index_msb;
+	return initial_apicid >> index_msb;
 }
 
 static void x2apic_send_IPI_self(int vector)
diff --git a/arch/x86/kernel/apic/x2apic_phys.c b/arch/x86/kernel/apic/x2apic_phys.c
index a284359627e..0b631c6a2e0 100644
--- a/arch/x86/kernel/apic/x2apic_phys.c
+++ b/arch/x86/kernel/apic/x2apic_phys.c
@@ -162,7 +162,7 @@ static unsigned long set_apic_id(unsigned int id)
 
 static int x2apic_phys_pkg_id(int initial_apicid, int index_msb)
 {
-	return current_cpu_data.initial_apicid >> index_msb;
+	return initial_apicid >> index_msb;
 }
 
 static void x2apic_send_IPI_self(int vector)
-- 
GitLab


From 6abf65510944d33b47575d151c6b318993c8d2b5 Mon Sep 17 00:00:00 2001
From: Jan Beulich <JBeulich@novell.com>
Date: Thu, 30 Jul 2009 16:49:30 +0100
Subject: [PATCH 0534/1153] x86, 32-bit: Fix double accounting in
 reserve_top_address()

With VMALLOC_END included in the calculation of MAXMEM (as of
2.6.28) it is no longer correct to also bump __VMALLOC_RESERVE
in reserve_top_address(). Doing so results in needlessly small
lowmem.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A71DD2A020000780000D482@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/mm/pgtable.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/x86/mm/pgtable.c b/arch/x86/mm/pgtable.c
index af8f9650058..ed34f5e3599 100644
--- a/arch/x86/mm/pgtable.c
+++ b/arch/x86/mm/pgtable.c
@@ -329,7 +329,6 @@ void __init reserve_top_address(unsigned long reserve)
 	printk(KERN_INFO "Reserving virtual address space above 0x%08x\n",
 	       (int)-reserve);
 	__FIXADDR_TOP = -reserve - PAGE_SIZE;
-	__VMALLOC_RESERVE += reserve;
 #endif
 }
 
-- 
GitLab


From 2a5ef41661b56cf4eee042a6967c4e14b63e8eac Mon Sep 17 00:00:00 2001
From: Jack Steiner <steiner@sgi.com>
Date: Mon, 20 Jul 2009 09:28:41 -0500
Subject: [PATCH 0535/1153] x86, UV: Complete IRQ interrupt migration in
 arch_enable_uv_irq()

In uv_setup_irq(), the call to create_irq() initially assigns
IRQ vectors to cpu 0. The subsequent call to
assign_irq_vector() in arch_enable_uv_irq() migrates the IRQ to
another cpu and frees the cpu 0 vector - at least it will be
freed as soon as the "IRQ move" completes.

arch_enable_uv_irq() needs to send a cleanup IPI to complete
the IRQ move. Otherwise, assignment of GRU interrupts on large
systems (>200 cpus) will exhaust the cpu 0 interrupt vectors
and initialization of the GRU driver will fail.

Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090720142840.GA8885@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/apic/io_apic.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c
index 2284a4812b6..d2ed6c5ddc8 100644
--- a/arch/x86/kernel/apic/io_apic.c
+++ b/arch/x86/kernel/apic/io_apic.c
@@ -3793,6 +3793,9 @@ int arch_enable_uv_irq(char *irq_name, unsigned int irq, int cpu, int mmr_blade,
 	mmr_pnode = uv_blade_to_pnode(mmr_blade);
 	uv_write_global_mmr64(mmr_pnode, mmr_offset, mmr_value);
 
+	if (cfg->move_in_progress)
+		send_cleanup_vector(cfg);
+
 	return irq;
 }
 
-- 
GitLab


From dc731fbbadf5d65c98fcd6c86472aa286c16458a Mon Sep 17 00:00:00 2001
From: Subrata Modak <subrata@linux.vnet.ibm.com>
Date: Tue, 21 Jul 2009 08:02:27 +0530
Subject: [PATCH 0536/1153] x86: Work around compilation warning in
 arch/x86/kernel/apm_32.c

The following fix was initially inspired by David Howells fix
few days back:

  http://lkml.org/lkml/2009/7/9/109

However, Ingo disapproves such fixes as it's dangerous (it can
hide future, relevant warnings) - in something as
performance-uncritical.

So, initialize 'err' to '0' to work around a GCC false positive
warning:

  http://lkml.org/lkml/2009/7/18/89

Signed-off-by: Subrata Modak<subrata@linux.vnet.ibm.com>
Cc: Sachin P Sant <sachinp@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20090721023226.31855.67236.sendpatchset@subratamodak.linux.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/apm_32.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/kernel/apm_32.c b/arch/x86/kernel/apm_32.c
index 79302e9a33a..442b5508893 100644
--- a/arch/x86/kernel/apm_32.c
+++ b/arch/x86/kernel/apm_32.c
@@ -811,7 +811,7 @@ static int apm_do_idle(void)
 	u8 ret = 0;
 	int idled = 0;
 	int polling;
-	int err;
+	int err = 0;
 
 	polling = !!(current_thread_info()->status & TS_POLLING);
 	if (polling) {
-- 
GitLab


From f26542600e605482a1231c44ddb2966d69bd09b0 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Mon, 29 Jun 2009 10:40:20 +0200
Subject: [PATCH 0537/1153] perf_counter: Set the CONFIG_PERF_COUNTERS default
 to y if CONFIG_PROFILING=y

If user has already enabled profiling support in the kernel
(for oprofile, old-style profiling of ftrace) then offer up
perfcounters with a y default in interactive kconfig sessions.

Still keep it off by default otherwise.

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 init/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/init/Kconfig b/init/Kconfig
index 823ee0a2d2a..3f7e60995c8 100644
--- a/init/Kconfig
+++ b/init/Kconfig
@@ -940,6 +940,7 @@ menu "Performance Counters"
 
 config PERF_COUNTERS
 	bool "Kernel Performance Counters"
+	default y if PROFILING
 	depends on HAVE_PERF_COUNTERS
 	select ANON_INODES
 	help
-- 
GitLab


From 1cef8e41073efe47e809f49670eb461307e52ccc Mon Sep 17 00:00:00 2001
From: Russell King <rmk+kernel@arm.linux.org.uk>
Date: Mon, 27 Jul 2009 11:30:48 +0530
Subject: [PATCH 0538/1153] mfd: twl4030 irq fixes

The TWL4030 IRQ handler has a bug which leads to spinlock lock-up. It is
calling the 'unmask' function in a process context. :The mask/unmask/ack
functions are only designed to be called from the IRQ handler code,
or the proper API interfaces found in linux/interrupt.h.

Also there is no need to have IRQ chaining mechanism. The right way to
handle this is to claim the parent interrupt as a standard interrupt
and arrange for handle_twl4030_pih to take care of the rest of the devices.

Mail thread on this issue can be found at:
http://marc.info/?l=linux-arm-kernel&m=124629940123396&w=2

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
---
 drivers/mfd/twl4030-irq.c | 55 +++++++++++++++++----------------------
 1 file changed, 24 insertions(+), 31 deletions(-)

diff --git a/drivers/mfd/twl4030-irq.c b/drivers/mfd/twl4030-irq.c
index bae61b22501..7d430835655 100644
--- a/drivers/mfd/twl4030-irq.c
+++ b/drivers/mfd/twl4030-irq.c
@@ -180,14 +180,9 @@ static struct completion irq_event;
 static int twl4030_irq_thread(void *data)
 {
 	long irq = (long)data;
-	struct irq_desc *desc = irq_to_desc(irq);
 	static unsigned i2c_errors;
 	static const unsigned max_i2c_errors = 100;
 
-	if (!desc) {
-		pr_err("twl4030: Invalid IRQ: %ld\n", irq);
-		return -EINVAL;
-	}
 
 	current->flags |= PF_NOFREEZE;
 
@@ -240,7 +235,7 @@ static int twl4030_irq_thread(void *data)
 		}
 		local_irq_enable();
 
-		desc->chip->unmask(irq);
+		enable_irq(irq);
 	}
 
 	return 0;
@@ -255,25 +250,13 @@ static int twl4030_irq_thread(void *data)
  * thread.  All we do here is acknowledge and mask the interrupt and wakeup
  * the kernel thread.
  */
-static void handle_twl4030_pih(unsigned int irq, struct irq_desc *desc)
+static irqreturn_t handle_twl4030_pih(int irq, void *devid)
 {
 	/* Acknowledge, clear *AND* mask the interrupt... */
-	desc->chip->ack(irq);
-	complete(&irq_event);
-}
-
-static struct task_struct *start_twl4030_irq_thread(long irq)
-{
-	struct task_struct *thread;
-
-	init_completion(&irq_event);
-	thread = kthread_run(twl4030_irq_thread, (void *)irq, "twl4030-irq");
-	if (!thread)
-		pr_err("twl4030: could not create irq %ld thread!\n", irq);
-
-	return thread;
+	disable_irq_nosync(irq);
+	complete(devid);
+	return IRQ_HANDLED;
 }
-
 /*----------------------------------------------------------------------*/
 
 /*
@@ -734,18 +717,28 @@ int twl_init_irq(int irq_num, unsigned irq_base, unsigned irq_end)
 	}
 
 	/* install an irq handler to demultiplex the TWL4030 interrupt */
-	task = start_twl4030_irq_thread(irq_num);
-	if (!task) {
-		pr_err("twl4030: irq thread FAIL\n");
-		status = -ESRCH;
-		goto fail;
-	}
 
-	set_irq_data(irq_num, task);
-	set_irq_chained_handler(irq_num, handle_twl4030_pih);
 
-	return status;
+	init_completion(&irq_event);
 
+	status = request_irq(irq_num, handle_twl4030_pih, IRQF_DISABLED,
+				"TWL4030-PIH", &irq_event);
+	if (status < 0) {
+		pr_err("twl4030: could not claim irq%d: %d\n", irq_num, status);
+		goto fail_rqirq;
+	}
+
+	task = kthread_run(twl4030_irq_thread, (void *)irq_num, "twl4030-irq");
+	if (IS_ERR(task)) {
+		pr_err("twl4030: could not create irq %d thread!\n", irq_num);
+		status = PTR_ERR(task);
+		goto fail_kthread;
+	}
+	return status;
+fail_kthread:
+	free_irq(irq_num, &irq_event);
+fail_rqirq:
+	/* clean up twl4030_sih_setup */
 fail:
 	for (i = irq_base; i < irq_end; i++)
 		set_irq_chip_and_handler(i, NULL, NULL);
-- 
GitLab


From 26d204afa18f7df177f21bdb3759e0098ca8f7d5 Mon Sep 17 00:00:00 2001
From: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Date: Wed, 29 Jul 2009 13:36:10 -0700
Subject: [PATCH 0539/1153] [CPUFREQ] Fix NULL pointer dereference regression
 in conservative governor

Commit ee88415caf736b89500f16e0a545614541a45005
introduced this regression when it removed enable bit in cpu_dbs_info_s.
That added a possibility of dbs_cpufreq_notifier getting called for a
CPU that is not yet managed by conservative governor. That will happen
as the transition notifier is set as soon as one CPU switches to
conservative governor and other CPUs can get a NULL pointer dereference
without the enable bit check. Add the enable bit back again.

Reported-by: Lermytte Christophe <Christophe.Lermytte@thomson.net>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
---
 drivers/cpufreq/cpufreq_conservative.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/cpufreq/cpufreq_conservative.c b/drivers/cpufreq/cpufreq_conservative.c
index 57490502b21..bdea7e2f94b 100644
--- a/drivers/cpufreq/cpufreq_conservative.c
+++ b/drivers/cpufreq/cpufreq_conservative.c
@@ -63,6 +63,7 @@ struct cpu_dbs_info_s {
 	unsigned int down_skip;
 	unsigned int requested_freq;
 	int cpu;
+	unsigned int enable:1;
 	/*
 	 * percpu mutex that serializes governor limit change with
 	 * do_dbs_timer invocation. We do not want do_dbs_timer to run
@@ -141,6 +142,9 @@ dbs_cpufreq_notifier(struct notifier_block *nb, unsigned long val,
 
 	struct cpufreq_policy *policy;
 
+	if (!this_dbs_info->enable)
+		return 0;
+
 	policy = this_dbs_info->cur_policy;
 
 	/*
@@ -497,6 +501,7 @@ static inline void dbs_timer_init(struct cpu_dbs_info_s *dbs_info)
 	int delay = usecs_to_jiffies(dbs_tuners_ins.sampling_rate);
 	delay -= jiffies % delay;
 
+	dbs_info->enable = 1;
 	INIT_DELAYED_WORK_DEFERRABLE(&dbs_info->work, do_dbs_timer);
 	queue_delayed_work_on(dbs_info->cpu, kconservative_wq, &dbs_info->work,
 				delay);
@@ -504,6 +509,7 @@ static inline void dbs_timer_init(struct cpu_dbs_info_s *dbs_info)
 
 static inline void dbs_timer_exit(struct cpu_dbs_info_s *dbs_info)
 {
+	dbs_info->enable = 0;
 	cancel_delayed_work_sync(&dbs_info->work);
 }
 
-- 
GitLab


From 42c74b84c64633dd3badbfc2abd2ef1728b64b30 Mon Sep 17 00:00:00 2001
From: Prarit Bhargava <prarit@redhat.com>
Date: Mon, 3 Aug 2009 10:58:11 -0400
Subject: [PATCH 0540/1153] [CPUFREQ] Do not set policy for offline cpus

Suspend/Resume fails on multi socket, multi core systems because the cpufreq
code erroneously sets the per_cpu policy_cpu value when a logical cpu is
offline.

This most notably results in missing sysfs files that are used to set the
cpu frequencies of the various cpus.

Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
---
 drivers/cpufreq/cpufreq.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c
index b90eda8b344..120d236c0ff 100644
--- a/drivers/cpufreq/cpufreq.c
+++ b/drivers/cpufreq/cpufreq.c
@@ -924,6 +924,8 @@ static int cpufreq_add_dev(struct sys_device *sys_dev)
 
 	spin_lock_irqsave(&cpufreq_driver_lock, flags);
 	for_each_cpu(j, policy->cpus) {
+		if (!cpu_online(j))
+			continue;
 		per_cpu(cpufreq_cpu_data, j) = policy;
 		per_cpu(policy_cpu, j) = policy->cpu;
 	}
-- 
GitLab


From d5194decd0a6f792b2789eebd4ddf022a248f655 Mon Sep 17 00:00:00 2001
From: Thomas Renninger <trenn@suse.de>
Date: Wed, 29 Jul 2009 11:26:20 +0200
Subject: [PATCH 0541/1153] [CPUFREQ] Fix a kobject reference bug related to
 managed CPUs

The first offline/online cycle is successful, the second not.
Doing:
echo 0 >cpu1/online
echo 1 >cpu1/online
echo 0 >cpu1/online

The last command will trigger:
Jul 22 14:39:50 linux kernel: [  593.210125] ------------[ cut here ]------------
Jul 22 14:39:50 linux kernel: [  593.210139] WARNING: at lib/kref.c:43 kref_get+0x23/0x2b()
Jul 22 14:39:50 linux kernel: [  593.210144] Hardware name: To Be Filled By O.E.M.
Jul 22 14:39:50 linux kernel: [  593.210148] Modules linked in: powernow_k8
Jul 22 14:39:50 linux kernel: [  593.210158] Pid: 378, comm: kondemand/2 Tainted: G        W  2.6.31-rc2 #38
Jul 22 14:39:50 linux kernel: [  593.210163] Call Trace:
Jul 22 14:39:50 linux kernel: [  593.210171]  [<ffffffff812008e8>] ? kref_get+0x23/0x2b
Jul 22 14:39:50 linux kernel: [  593.210181]  [<ffffffff81041926>] warn_slowpath_common+0x77/0xa4
Jul 22 14:39:50 linux kernel: [  593.210190]  [<ffffffff81041962>] warn_slowpath_null+0xf/0x11
Jul 22 14:39:50 linux kernel: [  593.210198]  [<ffffffff812008e8>] kref_get+0x23/0x2b
Jul 22 14:39:50 linux kernel: [  593.210206]  [<ffffffff811ffa19>] kobject_get+0x1a/0x22
Jul 22 14:39:50 linux kernel: [  593.210214]  [<ffffffff813e815d>] cpufreq_cpu_get+0x8a/0xcb
Jul 22 14:39:50 linux kernel: [  593.210222]  [<ffffffff813e87d1>] __cpufreq_driver_getavg+0x1d/0x67
Jul 22 14:39:50 linux kernel: [  593.210231]  [<ffffffff813ea18f>] do_dbs_timer+0x158/0x27f
Jul 22 14:39:50 linux kernel: [  593.210240]  [<ffffffff810529ea>] worker_thread+0x200/0x313
...

The output continues on every do_dbs_timer ondemand freq checking poll.
This regression was introduced by git commit:
3f4a782b5ce2698b1870b5a7b573cd721d4fce33

The policy is released when the cpufreq device is removed in:
__cpufreq_remove_dev():
	/* if this isn't the CPU which is the parent of the kobj, we
	 * only need to unlink, put and exit
	 */

Not creating the symlink is not sever at all.
As long as:
sysfs_remove_link(&sys_dev->kobj, "cpufreq");
handles it gracefully that the symlink did not exist.
Possibly no error should be returned at all, because ondemand
governor would still provide the same functionality.
Userspace in userspace gov case might be confused if the link
is missing.

Resolves http://bugzilla.kernel.org/show_bug.cgi?id=13903

CC: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
---
 drivers/cpufreq/cpufreq.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c
index 120d236c0ff..bd74a0b1217 100644
--- a/drivers/cpufreq/cpufreq.c
+++ b/drivers/cpufreq/cpufreq.c
@@ -858,6 +858,8 @@ static int cpufreq_add_dev(struct sys_device *sys_dev)
 
 		/* Check for existing affected CPUs.
 		 * They may not be aware of it due to CPU Hotplug.
+		 * cpufreq_cpu_put is called when the device is removed
+		 * in __cpufreq_remove_dev()
 		 */
 		managed_policy = cpufreq_cpu_get(j);
 		if (unlikely(managed_policy)) {
@@ -884,7 +886,7 @@ static int cpufreq_add_dev(struct sys_device *sys_dev)
 			ret = sysfs_create_link(&sys_dev->kobj,
 						&managed_policy->kobj,
 						"cpufreq");
-			if (!ret)
+			if (ret)
 				cpufreq_cpu_put(managed_policy);
 			/*
 			 * Success. We only needed to be added to the mask.
-- 
GitLab


From 4bc5d34135039566b8d6efa2de7515b2be505da8 Mon Sep 17 00:00:00 2001
From: Dave Jones <davej@redhat.com>
Date: Tue, 4 Aug 2009 14:03:25 -0400
Subject: [PATCH 0542/1153] [CPUFREQ] Make cpufreq suspend code conditional on
 powerpc.

The suspend code runs with interrupts disabled, and the powerpc workaround we
do in the cpufreq suspend hook calls the drivers ->get method.

powernow-k8's ->get does an smp_call_function_single
which needs interrupts enabled

cpufreq's suspend/resume code was added in 42d4dc3f4e1e to work around
a hardware problem on ppc powerbooks.  If we make all this code
conditional on powerpc, we avoid the issue above.

Signed-off-by: Dave Jones <davej@redhat.com>
---
 drivers/cpufreq/cpufreq.c | 21 +++++++++++++++++++--
 1 file changed, 19 insertions(+), 2 deletions(-)

diff --git a/drivers/cpufreq/cpufreq.c b/drivers/cpufreq/cpufreq.c
index bd74a0b1217..fd69086d08d 100644
--- a/drivers/cpufreq/cpufreq.c
+++ b/drivers/cpufreq/cpufreq.c
@@ -1248,13 +1248,22 @@ EXPORT_SYMBOL(cpufreq_get);
 
 static int cpufreq_suspend(struct sys_device *sysdev, pm_message_t pmsg)
 {
-	int cpu = sysdev->id;
 	int ret = 0;
+
+#ifdef __powerpc__
+	int cpu = sysdev->id;
 	unsigned int cur_freq = 0;
 	struct cpufreq_policy *cpu_policy;
 
 	dprintk("suspending cpu %u\n", cpu);
 
+	/*
+	 * This whole bogosity is here because Powerbooks are made of fail.
+	 * No sane platform should need any of the code below to be run.
+	 * (it's entirely the wrong thing to do, as driver->get may
+	 *  reenable interrupts on some architectures).
+	 */
+
 	if (!cpu_online(cpu))
 		return 0;
 
@@ -1313,6 +1322,7 @@ static int cpufreq_suspend(struct sys_device *sysdev, pm_message_t pmsg)
 
 out:
 	cpufreq_cpu_put(cpu_policy);
+#endif	/* __powerpc__ */
 	return ret;
 }
 
@@ -1326,12 +1336,18 @@ out:
  */
 static int cpufreq_resume(struct sys_device *sysdev)
 {
-	int cpu = sysdev->id;
 	int ret = 0;
+
+#ifdef __powerpc__
+	int cpu = sysdev->id;
 	struct cpufreq_policy *cpu_policy;
 
 	dprintk("resuming cpu %u\n", cpu);
 
+	/* As with the ->suspend method, all the code below is
+	 * only necessary because Powerbooks suck.
+	 * See commit 42d4dc3f4e1e for jokes. */
+
 	if (!cpu_online(cpu))
 		return 0;
 
@@ -1395,6 +1411,7 @@ out:
 	schedule_work(&cpu_policy->update);
 fail:
 	cpufreq_cpu_put(cpu_policy);
+#endif	/* __powerpc__ */
 	return ret;
 }
 
-- 
GitLab


From e0cff5ed27acd355264b210d9622da801a431e19 Mon Sep 17 00:00:00 2001
From: Alexander Duyck <alexander.h.duyck@intel.com>
Date: Tue, 4 Aug 2009 11:46:41 -0700
Subject: [PATCH 0543/1153] igbvf: Allow VF driver to correctly recognize
 failure to set mac

The VF driver was not correctly recognizing that it did not correctly set
it's mac address.  As a result the VF driver was unable to receive network
traffic until being unloaded and reloaded.  The issue was root caused to
the fact that the CTS bit was not taken into account when checking for the
request being NAKed.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/igbvf/vf.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/igbvf/vf.c b/drivers/net/igbvf/vf.c
index 2a4faf9ade6..a9a61efa964 100644
--- a/drivers/net/igbvf/vf.c
+++ b/drivers/net/igbvf/vf.c
@@ -274,6 +274,8 @@ static s32 e1000_set_vfta_vf(struct e1000_hw *hw, u16 vid, bool set)
 
 	err = mbx->ops.read_posted(hw, msgbuf, 2);
 
+	msgbuf[0] &= ~E1000_VT_MSGTYPE_CTS;
+
 	/* if nacked the vlan was rejected */
 	if (!err && (msgbuf[0] == (E1000_VF_SET_VLAN | E1000_VT_MSGTYPE_NACK)))
 		err = -E1000_ERR_MAC_INIT;
@@ -317,6 +319,8 @@ static void e1000_rar_set_vf(struct e1000_hw *hw, u8 * addr, u32 index)
 	if (!ret_val)
 		ret_val = mbx->ops.read_posted(hw, msgbuf, 3);
 
+	msgbuf[0] &= ~E1000_VT_MSGTYPE_CTS;
+
 	/* if nacked the address was rejected, use "perm_addr" */
 	if (!ret_val &&
 	    (msgbuf[0] == (E1000_VF_SET_MAC_ADDR | E1000_VT_MSGTYPE_NACK)))
-- 
GitLab


From 357eb46d8f275b4e8484541234ea3ba06065e258 Mon Sep 17 00:00:00 2001
From: Hannes Hering <hering2@de.ibm.com>
Date: Tue, 4 Aug 2009 11:48:39 -0700
Subject: [PATCH 0544/1153] ehea: Fix napi list corruption on ifconfig down

This patch fixes the napi list handling when an ehea interface is shut
down to avoid corruption of the napi list.

Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ehea/ehea.h      | 2 +-
 drivers/net/ehea/ehea_main.c | 3 +++
 2 files changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ehea/ehea.h b/drivers/net/ehea/ehea.h
index 78952f8324e..fa311a95099 100644
--- a/drivers/net/ehea/ehea.h
+++ b/drivers/net/ehea/ehea.h
@@ -40,7 +40,7 @@
 #include <asm/io.h>
 
 #define DRV_NAME	"ehea"
-#define DRV_VERSION	"EHEA_0101"
+#define DRV_VERSION	"EHEA_0102"
 
 /* eHEA capability flags */
 #define DLPAR_PORT_ADD_REM 1
diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c
index e8d46cc1bec..977c3d35827 100644
--- a/drivers/net/ehea/ehea_main.c
+++ b/drivers/net/ehea/ehea_main.c
@@ -1545,6 +1545,9 @@ static int ehea_clean_portres(struct ehea_port *port, struct ehea_port_res *pr)
 {
 	int ret, i;
 
+	if (pr->qp)
+		netif_napi_del(&pr->napi);
+
 	ret = ehea_destroy_qp(pr->qp);
 
 	if (!ret) {
-- 
GitLab


From 14d9fa352592582e457cf75022202766baac1348 Mon Sep 17 00:00:00 2001
From: John Stoffel <john@stoffel.org>
Date: Tue, 4 Aug 2009 22:10:17 +0200
Subject: [PATCH 0545/1153] Make SCSI SG v4 driver enabled by default and
 remove EXPERIMENTAL dependency, since udev depends on BSG

Make Block Layer SG support v4 the default, since recent udev versions
depend on this to access serial numbers and other low level info properly.

This should be backported to older kernels as well, since most distros have
enabled this for a long time.

Signed-off-by: John Stoffel <john@stoffel.org>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 block/Kconfig | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/block/Kconfig b/block/Kconfig
index 95a86adc33a..9be0b56eaee 100644
--- a/block/Kconfig
+++ b/block/Kconfig
@@ -48,9 +48,9 @@ config LBDAF
 	  If unsure, say Y.
 
 config BLK_DEV_BSG
-	bool "Block layer SG support v4 (EXPERIMENTAL)"
-	depends on EXPERIMENTAL
-	---help---
+	bool "Block layer SG support v4"
+	default y
+	help
 	  Saying Y here will enable generic SG (SCSI generic) v4 support
 	  for any block device.
 
@@ -60,7 +60,10 @@ config BLK_DEV_BSG
 	  protocols (e.g. Task Management Functions and SMP in Serial
 	  Attached SCSI).
 
-	  If unsure, say N.
+	  This option is required by recent UDEV versions to properly
+	  access device serial numbers, etc.
+
+	  If unsure, say Y.
 
 config BLK_DEV_INTEGRITY
 	bool "Block layer data integrity support"
-- 
GitLab


From 18eac1cc100fa2afd5f39085aae6b694e417734b Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Mon, 3 Aug 2009 10:58:29 -0700
Subject: [PATCH 0546/1153] tty-ldisc: make refcount be atomic_t 'users' count

This is pure preparation of changing the ldisc reference counting to be
a true refcount that defines the lifetime of the ldisc.  But this is a
purely syntactic change for now to make the next steps easier.

This patch should make no semantic changes at all. But I wanted to make
the ldisc refcount be an atomic (I will be touching it without locks
soon enough), and I wanted to rename it so that there isn't quite as
much confusion between 'ldo->refcount' (ldisk operations refcount) and
'ld->refcount' (ldisc refcount itself) in the same file.

So it's now an atomic 'ld->users' count. It still starts at zero,
despite having a reference from 'tty->ldisc', but that will change once
we turn it into a _real_ refcount.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/char/tty_ldisc.c  | 18 ++++++++----------
 include/linux/tty_ldisc.h |  2 +-
 2 files changed, 9 insertions(+), 11 deletions(-)

diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c
index acd76b767d4..fd175e60aad 100644
--- a/drivers/char/tty_ldisc.c
+++ b/drivers/char/tty_ldisc.c
@@ -142,7 +142,7 @@ static struct tty_ldisc *tty_ldisc_try_get(int disc)
 			/* lock it */
 			ldops->refcount++;
 			ld->ops = ldops;
-			ld->refcount = 0;
+			atomic_set(&ld->users, 0);
 			err = 0;
 		}
 	}
@@ -206,7 +206,7 @@ static void tty_ldisc_put(struct tty_ldisc *ld)
 	ldo->refcount--;
 	module_put(ldo->owner);
 	spin_unlock_irqrestore(&tty_ldisc_lock, flags);
-	WARN_ON(ld->refcount);
+	WARN_ON(atomic_read(&ld->users));
 	kfree(ld);
 }
 
@@ -297,7 +297,7 @@ static int tty_ldisc_try(struct tty_struct *tty)
 	spin_lock_irqsave(&tty_ldisc_lock, flags);
 	ld = tty->ldisc;
 	if (test_bit(TTY_LDISC, &tty->flags)) {
-		ld->refcount++;
+		atomic_inc(&ld->users);
 		ret = 1;
 	}
 	spin_unlock_irqrestore(&tty_ldisc_lock, flags);
@@ -324,7 +324,7 @@ struct tty_ldisc *tty_ldisc_ref_wait(struct tty_struct *tty)
 {
 	/* wait_event is a macro */
 	wait_event(tty_ldisc_wait, tty_ldisc_try(tty));
-	WARN_ON(tty->ldisc->refcount == 0);
+	WARN_ON(atomic_read(&tty->ldisc->users) == 0);
 	return tty->ldisc;
 }
 EXPORT_SYMBOL_GPL(tty_ldisc_ref_wait);
@@ -365,11 +365,9 @@ void tty_ldisc_deref(struct tty_ldisc *ld)
 	BUG_ON(ld == NULL);
 
 	spin_lock_irqsave(&tty_ldisc_lock, flags);
-	if (ld->refcount == 0)
+	if (atomic_read(&ld->users) == 0)
 		printk(KERN_ERR "tty_ldisc_deref: no references.\n");
-	else
-		ld->refcount--;
-	if (ld->refcount == 0)
+	else if (atomic_dec_and_test(&ld->users))
 		wake_up(&tty_ldisc_wait);
 	spin_unlock_irqrestore(&tty_ldisc_lock, flags);
 }
@@ -536,10 +534,10 @@ static int tty_ldisc_wait_idle(struct tty_struct *tty)
 {
 	unsigned long flags;
 	spin_lock_irqsave(&tty_ldisc_lock, flags);
-	while (tty->ldisc->refcount) {
+	while (atomic_read(&tty->ldisc->users)) {
 		spin_unlock_irqrestore(&tty_ldisc_lock, flags);
 		if (wait_event_timeout(tty_ldisc_wait,
-				tty->ldisc->refcount == 0, 5 * HZ) == 0)
+				atomic_read(&tty->ldisc->users) == 0, 5 * HZ) == 0)
 			return -EBUSY;
 		spin_lock_irqsave(&tty_ldisc_lock, flags);
 	}
diff --git a/include/linux/tty_ldisc.h b/include/linux/tty_ldisc.h
index 40f38d89677..0c4ee9b88f8 100644
--- a/include/linux/tty_ldisc.h
+++ b/include/linux/tty_ldisc.h
@@ -144,7 +144,7 @@ struct tty_ldisc_ops {
 
 struct tty_ldisc {
 	struct tty_ldisc_ops *ops;
-	int refcount;
+	atomic_t users;
 };
 
 #define TTY_LDISC_MAGIC	0x5403
-- 
GitLab


From 65b770468e98941e45e19780dff9283e663e6b8b Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Mon, 3 Aug 2009 11:11:19 -0700
Subject: [PATCH 0547/1153] tty-ldisc: turn ldisc user count into a proper
 refcount

By using the user count for the actual lifetime rules, we can get rid of
the silly "wait_for_idle" logic, because any busy ldisc will
automatically stay around until the last user releases it.  This avoids
a host of odd issues, and simplifies the code.

So now, when the last ldisc reference is dropped, we just release the
ldisc operations struct reference, and free the ldisc.

It looks obvious enough, and it does work for me, but the counting
_could_ be off. It probably isn't (bad counting in the new version would
generally imply that the old code did something really bad, like free an
ldisc with a non-zero count), but it does need some testing, and
preferably somebody looking at it.

With this change, both 'tty_ldisc_put()' and 'tty_ldisc_deref()' are
just aliases for the new ref-counting 'put_ldisc()'. Both of them
decrement the ldisc user count and free it if it goes down to zero.
They're identical functions, in other words.

But the reason they still exist as sepate functions is that one of them
was exported (tty_ldisc_deref) and had a stupid name (so I don't want to
use it as the main name), and the other one was used in multiple places
(and I didn't want to make the patch larger just to rename the users).

In addition to the refcounting, I did do some minimal cleanup. For
example, now "tty_ldisc_try()" actually returns the ldisc it got under
the lock, rather than returning true/false and then the caller would
look up the ldisc again (now without the protection of the lock).

That said, there's tons of dubious use of 'tty->ldisc' without obviously
proper locking or refcounting left. I expressly did _not_ want to try to
fix it all, keeping the patch minimal. There may or may not be bugs in
that kind of code, but they wouldn't be _new_ bugs.

That said, even if the bugs aren't new, the timing and lifetime will
change. For example, some silly code may depend on the 'tty->ldisc'
pointer not changing because they hold a refcount on the 'ldisc'. And
that's no longer true - if you hold a ref on the ldisc, the 'ldisc'
itself is safe, but tty->ldisc may change.

So the proper locking (remains) to hold tty->ldisc_mutex if you expect
tty->ldisc to be stable. That's not really a _new_ rule, but it's an
example of something that the old code might have unintentionally
depended on and hidden bugs.

Whatever. The patch _looks_ sensible to me. The only users of
ldisc->users are:
 - get_ldisc() - atomically increment the count

 - put_ldisc() - atomically decrements the count and releases if zero

 - tty_ldisc_try_get() - creates the ldisc, and sets the count to 1.
   The ldisc should then either be released, or be attached to a tty.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/char/tty_ldisc.c | 143 +++++++++++++--------------------------
 1 file changed, 46 insertions(+), 97 deletions(-)

diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c
index fd175e60aad..be55dfcf59a 100644
--- a/drivers/char/tty_ldisc.c
+++ b/drivers/char/tty_ldisc.c
@@ -48,6 +48,34 @@ static DECLARE_WAIT_QUEUE_HEAD(tty_ldisc_wait);
 /* Line disc dispatch table */
 static struct tty_ldisc_ops *tty_ldiscs[NR_LDISCS];
 
+static inline struct tty_ldisc *get_ldisc(struct tty_ldisc *ld)
+{
+	if (ld)
+		atomic_inc(&ld->users);
+	return ld;
+}
+
+static inline void put_ldisc(struct tty_ldisc *ld)
+{
+	if (WARN_ON_ONCE(!ld))
+		return;
+
+	/*
+	 * If this is the last user, free the ldisc, and
+	 * release the ldisc ops.
+	 */
+	if (atomic_dec_and_test(&ld->users)) {
+		unsigned long flags;
+		struct tty_ldisc_ops *ldo = ld->ops;
+
+		kfree(ld);
+		spin_lock_irqsave(&tty_ldisc_lock, flags);
+		ldo->refcount--;
+		module_put(ldo->owner);
+		spin_unlock_irqrestore(&tty_ldisc_lock, flags);
+	}
+}
+
 /**
  *	tty_register_ldisc	-	install a line discipline
  *	@disc: ldisc number
@@ -142,7 +170,7 @@ static struct tty_ldisc *tty_ldisc_try_get(int disc)
 			/* lock it */
 			ldops->refcount++;
 			ld->ops = ldops;
-			atomic_set(&ld->users, 0);
+			atomic_set(&ld->users, 1);
 			err = 0;
 		}
 	}
@@ -181,35 +209,6 @@ static struct tty_ldisc *tty_ldisc_get(int disc)
 	return ld;
 }
 
-/**
- *	tty_ldisc_put		-	drop ldisc reference
- *	@ld: ldisc
- *
- *	Drop a reference to a line discipline. Manage refcounts and
- *	module usage counts. Free the ldisc once the recount hits zero.
- *
- *	Locking:
- *		takes tty_ldisc_lock to guard against ldisc races
- */
-
-static void tty_ldisc_put(struct tty_ldisc *ld)
-{
-	unsigned long flags;
-	int disc = ld->ops->num;
-	struct tty_ldisc_ops *ldo;
-
-	BUG_ON(disc < N_TTY || disc >= NR_LDISCS);
-
-	spin_lock_irqsave(&tty_ldisc_lock, flags);
-	ldo = tty_ldiscs[disc];
-	BUG_ON(ldo->refcount == 0);
-	ldo->refcount--;
-	module_put(ldo->owner);
-	spin_unlock_irqrestore(&tty_ldisc_lock, flags);
-	WARN_ON(atomic_read(&ld->users));
-	kfree(ld);
-}
-
 static void *tty_ldiscs_seq_start(struct seq_file *m, loff_t *pos)
 {
 	return (*pos < NR_LDISCS) ? pos : NULL;
@@ -234,7 +233,7 @@ static int tty_ldiscs_seq_show(struct seq_file *m, void *v)
 	if (IS_ERR(ld))
 		return 0;
 	seq_printf(m, "%-10s %2d\n", ld->ops->name ? ld->ops->name : "???", i);
-	tty_ldisc_put(ld);
+	put_ldisc(ld);
 	return 0;
 }
 
@@ -288,20 +287,17 @@ static void tty_ldisc_assign(struct tty_struct *tty, struct tty_ldisc *ld)
  *	Locking: takes tty_ldisc_lock
  */
 
-static int tty_ldisc_try(struct tty_struct *tty)
+static struct tty_ldisc *tty_ldisc_try(struct tty_struct *tty)
 {
 	unsigned long flags;
 	struct tty_ldisc *ld;
-	int ret = 0;
 
 	spin_lock_irqsave(&tty_ldisc_lock, flags);
-	ld = tty->ldisc;
-	if (test_bit(TTY_LDISC, &tty->flags)) {
-		atomic_inc(&ld->users);
-		ret = 1;
-	}
+	ld = NULL;
+	if (test_bit(TTY_LDISC, &tty->flags))
+		ld = get_ldisc(tty->ldisc);
 	spin_unlock_irqrestore(&tty_ldisc_lock, flags);
-	return ret;
+	return ld;
 }
 
 /**
@@ -322,10 +318,11 @@ static int tty_ldisc_try(struct tty_struct *tty)
 
 struct tty_ldisc *tty_ldisc_ref_wait(struct tty_struct *tty)
 {
+	struct tty_ldisc *ld;
+
 	/* wait_event is a macro */
-	wait_event(tty_ldisc_wait, tty_ldisc_try(tty));
-	WARN_ON(atomic_read(&tty->ldisc->users) == 0);
-	return tty->ldisc;
+	wait_event(tty_ldisc_wait, (ld = tty_ldisc_try(tty)) != NULL);
+	return ld;
 }
 EXPORT_SYMBOL_GPL(tty_ldisc_ref_wait);
 
@@ -342,9 +339,7 @@ EXPORT_SYMBOL_GPL(tty_ldisc_ref_wait);
 
 struct tty_ldisc *tty_ldisc_ref(struct tty_struct *tty)
 {
-	if (tty_ldisc_try(tty))
-		return tty->ldisc;
-	return NULL;
+	return tty_ldisc_try(tty);
 }
 EXPORT_SYMBOL_GPL(tty_ldisc_ref);
 
@@ -360,19 +355,15 @@ EXPORT_SYMBOL_GPL(tty_ldisc_ref);
 
 void tty_ldisc_deref(struct tty_ldisc *ld)
 {
-	unsigned long flags;
-
-	BUG_ON(ld == NULL);
-
-	spin_lock_irqsave(&tty_ldisc_lock, flags);
-	if (atomic_read(&ld->users) == 0)
-		printk(KERN_ERR "tty_ldisc_deref: no references.\n");
-	else if (atomic_dec_and_test(&ld->users))
-		wake_up(&tty_ldisc_wait);
-	spin_unlock_irqrestore(&tty_ldisc_lock, flags);
+	put_ldisc(ld);
 }
 EXPORT_SYMBOL_GPL(tty_ldisc_deref);
 
+static inline void tty_ldisc_put(struct tty_ldisc *ld)
+{
+	put_ldisc(ld);
+}
+
 /**
  *	tty_ldisc_enable	-	allow ldisc use
  *	@tty: terminal to activate ldisc on
@@ -520,31 +511,6 @@ static int tty_ldisc_halt(struct tty_struct *tty)
 	return cancel_delayed_work(&tty->buf.work);
 }
 
-/**
- *	tty_ldisc_wait_idle	-	wait for the ldisc to become idle
- *	@tty: tty to wait for
- *
- *	Wait for the line discipline to become idle. The discipline must
- *	have been halted for this to guarantee it remains idle.
- *
- *	tty_ldisc_lock protects the ref counts currently.
- */
-
-static int tty_ldisc_wait_idle(struct tty_struct *tty)
-{
-	unsigned long flags;
-	spin_lock_irqsave(&tty_ldisc_lock, flags);
-	while (atomic_read(&tty->ldisc->users)) {
-		spin_unlock_irqrestore(&tty_ldisc_lock, flags);
-		if (wait_event_timeout(tty_ldisc_wait,
-				atomic_read(&tty->ldisc->users) == 0, 5 * HZ) == 0)
-			return -EBUSY;
-		spin_lock_irqsave(&tty_ldisc_lock, flags);
-	}
-	spin_unlock_irqrestore(&tty_ldisc_lock, flags);
-	return 0;
-}
-
 /**
  *	tty_set_ldisc		-	set line discipline
  *	@tty: the terminal to set
@@ -640,14 +606,6 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 
 	flush_scheduled_work();
 
-	/* Let any existing reference holders finish */
-	retval = tty_ldisc_wait_idle(tty);
-	if (retval < 0) {
-		clear_bit(TTY_LDISC_CHANGING, &tty->flags);
-		tty_ldisc_put(new_ldisc);
-		return retval;
-	}
-
 	mutex_lock(&tty->ldisc_mutex);
 	if (test_bit(TTY_HUPPED, &tty->flags)) {
 		/* We were raced by the hangup method. It will have stomped
@@ -793,7 +751,6 @@ void tty_ldisc_hangup(struct tty_struct *tty)
 		if (tty->ldisc) {	/* Not yet closed */
 			/* Switch back to N_TTY */
 			tty_ldisc_halt(tty);
-			tty_ldisc_wait_idle(tty);
 			tty_ldisc_reinit(tty);
 			/* At this point we have a closed ldisc and we want to
 			   reopen it. We could defer this to the next open but
@@ -858,14 +815,6 @@ void tty_ldisc_release(struct tty_struct *tty, struct tty_struct *o_tty)
 	tty_ldisc_halt(tty);
 	flush_scheduled_work();
 
-	/*
-	 * Wait for any short term users (we know they are just driver
-	 * side waiters as the file is closing so user count on the file
-	 * side is zero.
-	 */
-
-	tty_ldisc_wait_idle(tty);
-
 	mutex_lock(&tty->ldisc_mutex);
 	/*
 	 * Now kill off the ldisc
-- 
GitLab


From cbe9352fa08f90aa03b4dbf1bbabfc95d196e562 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Mon, 3 Aug 2009 14:54:56 -0700
Subject: [PATCH 0548/1153] tty-ldisc: be more careful in 'put_ldisc' locking

Use 'atomic_dec_and_lock()' to make sure that we always hold the
tty_ldisc_lock when the ldisc count goes to zero. That way we can never
race against 'tty_ldisc_try()' increasing the count again.

Reported-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/char/tty_ldisc.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c
index be55dfcf59a..1733d3439ad 100644
--- a/drivers/char/tty_ldisc.c
+++ b/drivers/char/tty_ldisc.c
@@ -55,25 +55,32 @@ static inline struct tty_ldisc *get_ldisc(struct tty_ldisc *ld)
 	return ld;
 }
 
-static inline void put_ldisc(struct tty_ldisc *ld)
+static void put_ldisc(struct tty_ldisc *ld)
 {
+	unsigned long flags;
+
 	if (WARN_ON_ONCE(!ld))
 		return;
 
 	/*
 	 * If this is the last user, free the ldisc, and
 	 * release the ldisc ops.
+	 *
+	 * We really want an "atomic_dec_and_lock_irqsave()",
+	 * but we don't have it, so this does it by hand.
 	 */
-	if (atomic_dec_and_test(&ld->users)) {
-		unsigned long flags;
+	local_irq_save(flags);
+	if (atomic_dec_and_lock(&ld->users, &tty_ldisc_lock)) {
 		struct tty_ldisc_ops *ldo = ld->ops;
 
-		kfree(ld);
-		spin_lock_irqsave(&tty_ldisc_lock, flags);
 		ldo->refcount--;
 		module_put(ldo->owner);
 		spin_unlock_irqrestore(&tty_ldisc_lock, flags);
+
+		kfree(ld);
+		return;
 	}
+	local_irq_restore(flags);
 }
 
 /**
-- 
GitLab


From 07868201070d87484bd00610a4921e879be78746 Mon Sep 17 00:00:00 2001
From: Jonathan Corbet <corbet@lwn.net>
Date: Tue, 4 Aug 2009 13:35:17 -0600
Subject: [PATCH 0549/1153] flex_array: remove unneeded index calculation

flex_array_get() calculates an index value, then drops it on the floor;
simply remove it.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 lib/flex_array.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/lib/flex_array.c b/lib/flex_array.c
index 0e7894ce888..08f1636d296 100644
--- a/lib/flex_array.c
+++ b/lib/flex_array.c
@@ -254,7 +254,6 @@ void *flex_array_get(struct flex_array *fa, int element_nr)
 {
 	int part_nr = fa_element_to_part_nr(fa, element_nr);
 	struct flex_array_part *part;
-	int index;
 
 	if (element_nr >= fa->total_nr_elements)
 		return NULL;
@@ -264,6 +263,5 @@ void *flex_array_get(struct flex_array *fa, int element_nr)
 		part = (struct flex_array_part *)&fa->parts[0];
 	else
 		part = fa->parts[part_nr];
-	index = index_inside_part(fa, element_nr);
 	return &part->elements[index_inside_part(fa, element_nr)];
 }
-- 
GitLab


From 6502fbfaf81b09b3f474bb7b3796257e9450273e Mon Sep 17 00:00:00 2001
From: Alex Deucher <alexdeucher@gmail.com>
Date: Tue, 4 Aug 2009 11:24:24 -0400
Subject: [PATCH 0550/1153] drm/radeon: Add support for RS880 chips

These are new AMD IGP chips

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r600_cp.c    | 22 +++++++++++++++-------
 drivers/gpu/drm/radeon/radeon_drv.h |  1 +
 include/drm/drm_pciids.h            |  5 +++++
 3 files changed, 21 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/radeon/r600_cp.c b/drivers/gpu/drm/radeon/r600_cp.c
index 146f3570af8..20f17908b03 100644
--- a/drivers/gpu/drm/radeon/r600_cp.c
+++ b/drivers/gpu/drm/radeon/r600_cp.c
@@ -384,8 +384,9 @@ static void r600_cp_load_microcode(drm_radeon_private_t *dev_priv)
 		DRM_INFO("Loading RV670 PFP Microcode\n");
 		for (i = 0; i < PFP_UCODE_SIZE; i++)
 			RADEON_WRITE(R600_CP_PFP_UCODE_DATA, RV670_pfp_microcode[i]);
-	} else if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) {
-		DRM_INFO("Loading RS780 CP Microcode\n");
+	} else if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) ||
+		   ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) {
+		DRM_INFO("Loading RS780/RS880 CP Microcode\n");
 		for (i = 0; i < PM4_UCODE_SIZE; i++) {
 			RADEON_WRITE(R600_CP_ME_RAM_DATA,
 				     RS780_cp_microcode[i][0]);
@@ -396,7 +397,7 @@ static void r600_cp_load_microcode(drm_radeon_private_t *dev_priv)
 		}
 
 		RADEON_WRITE(R600_CP_PFP_UCODE_ADDR, 0);
-		DRM_INFO("Loading RS780 PFP Microcode\n");
+		DRM_INFO("Loading RS780/RS880 PFP Microcode\n");
 		for (i = 0; i < PFP_UCODE_SIZE; i++)
 			RADEON_WRITE(R600_CP_PFP_UCODE_DATA, RS780_pfp_microcode[i]);
 	}
@@ -783,6 +784,7 @@ static void r600_gfx_init(struct drm_device *dev,
 		break;
 	case CHIP_RV610:
 	case CHIP_RS780:
+	case CHIP_RS880:
 	case CHIP_RV620:
 		dev_priv->r600_max_pipes = 1;
 		dev_priv->r600_max_tile_pipes = 1;
@@ -917,7 +919,8 @@ static void r600_gfx_init(struct drm_device *dev,
 	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV630) ||
 	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) ||
 	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) ||
-	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780))
+	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) ||
+	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880))
 		RADEON_WRITE(R600_DB_DEBUG, R600_PREZ_MUST_WAIT_FOR_POSTZ_DONE);
 	else
 		RADEON_WRITE(R600_DB_DEBUG, 0);
@@ -935,7 +938,8 @@ static void r600_gfx_init(struct drm_device *dev,
 	sq_ms_fifo_sizes = RADEON_READ(R600_SQ_MS_FIFO_SIZES);
 	if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) ||
 	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) ||
-	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) {
+	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) ||
+	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) {
 		sq_ms_fifo_sizes = (R600_CACHE_FIFO_SIZE(0xa) |
 				    R600_FETCH_FIFO_HIWATER(0xa) |
 				    R600_DONE_FIFO_HIWATER(0xe0) |
@@ -978,7 +982,8 @@ static void r600_gfx_init(struct drm_device *dev,
 					    R600_NUM_ES_STACK_ENTRIES(0));
 	} else if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) ||
 		   ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) ||
-		   ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780)) {
+		   ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) ||
+		   ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880)) {
 		/* no vertex cache */
 		sq_config &= ~R600_VC_ENABLE;
 
@@ -1035,7 +1040,8 @@ static void r600_gfx_init(struct drm_device *dev,
 
 	if (((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV610) ||
 	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV620) ||
-	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780))
+	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS780) ||
+	    ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RS880))
 		RADEON_WRITE(R600_VGT_CACHE_INVALIDATION, R600_CACHE_INVALIDATION(R600_TC_ONLY));
 	else
 		RADEON_WRITE(R600_VGT_CACHE_INVALIDATION, R600_CACHE_INVALIDATION(R600_VC_AND_TC));
@@ -1078,6 +1084,7 @@ static void r600_gfx_init(struct drm_device *dev,
 		break;
 	case CHIP_RV610:
 	case CHIP_RS780:
+	case CHIP_RS880:
 	case CHIP_RV620:
 		gs_prim_buffer_depth = 32;
 		break;
@@ -1123,6 +1130,7 @@ static void r600_gfx_init(struct drm_device *dev,
 	switch (dev_priv->flags & RADEON_FAMILY_MASK) {
 	case CHIP_RV610:
 	case CHIP_RS780:
+	case CHIP_RS880:
 	case CHIP_RV620:
 		tc_cntl = R600_TC_L2_SIZE(8);
 		break;
diff --git a/drivers/gpu/drm/radeon/radeon_drv.h b/drivers/gpu/drm/radeon/radeon_drv.h
index 127d0456f62..3933f8216a3 100644
--- a/drivers/gpu/drm/radeon/radeon_drv.h
+++ b/drivers/gpu/drm/radeon/radeon_drv.h
@@ -143,6 +143,7 @@ enum radeon_family {
 	CHIP_RV635,
 	CHIP_RV670,
 	CHIP_RS780,
+	CHIP_RS880,
 	CHIP_RV770,
 	CHIP_RV730,
 	CHIP_RV710,
diff --git a/include/drm/drm_pciids.h b/include/drm/drm_pciids.h
index 9d4c0049154..853508499d2 100644
--- a/include/drm/drm_pciids.h
+++ b/include/drm/drm_pciids.h
@@ -370,6 +370,11 @@
 	{0x1002, 0x9614, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS780|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \
 	{0x1002, 0x9615, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS780|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \
 	{0x1002, 0x9616, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS780|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \
+	{0x1002, 0x9710, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \
+	{0x1002, 0x9711, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \
+	{0x1002, 0x9712, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \
+	{0x1002, 0x9713, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \
+	{0x1002, 0x9714, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_RS880|RADEON_NEW_MEMMAP|RADEON_IS_IGP}, \
 	{0, 0, 0}
 
 #define r128_PCI_IDS \
-- 
GitLab


From 685aaca751271b2c5191901931a19ccaceeae1ce Mon Sep 17 00:00:00 2001
From: "Jory A. Pratt" <geekypenguin@gmail.com>
Date: Mon, 3 Aug 2009 09:32:34 -0700
Subject: [PATCH 0551/1153] Input: i8042 - add Asus G1S to noloop exception
 list

The synaptic touchpad on the Asus G1S is not properly detected when
rebooting machine or on cold boot from time to time. Adding the Asus
G1S to the noloop exception table resolves the issue.

# dmidecode 2.10
SMBIOS 2.4 present.

Handle 0x0001, DMI type 1, 27 bytes
System Information
     Manufacturer: ASUSTeK Computer Inc.
     Product Name: G1S
     Version: 1.0
     Wake-up Type: Power Switch
     SKU Number:
     Family:

Signed-off-by: Jory A. Pratt <geekypenguin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
---
 drivers/input/serio/i8042-x86ia64io.h | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/input/serio/i8042-x86ia64io.h b/drivers/input/serio/i8042-x86ia64io.h
index 924e8ed7f2c..ae04d8a494e 100644
--- a/drivers/input/serio/i8042-x86ia64io.h
+++ b/drivers/input/serio/i8042-x86ia64io.h
@@ -77,6 +77,14 @@ static struct dmi_system_id __initdata i8042_dmi_noloop_table[] = {
 			DMI_MATCH(DMI_BOARD_VERSION, "Rev E"),
 		},
 	},
+	{
+		.ident = "ASUS G1S",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK Computer Inc."),
+			DMI_MATCH(DMI_BOARD_NAME, "G1S"),
+			DMI_MATCH(DMI_BOARD_VERSION, "1.0"),
+		},
+	},
 	{
 		/* AUX LOOP command does not raise AUX IRQ */
 		.ident = "ASUS P65UP5",
-- 
GitLab


From f532959b77e5e567c84c914cb7c7b07d2582448b Mon Sep 17 00:00:00 2001
From: Fenghua Yu <fenghua.yu@intel.com>
Date: Tue, 4 Aug 2009 15:09:37 -0700
Subject: [PATCH 0552/1153] intel-iommu: Correct sglist size calculation.

In domain_sg_mapping(), use aligned_nrpages() instead of hand-coded
rounding code for calculating the size of each sg elem. This means that
on IA64 we correctly round up to the MM page size, not just to the VT-d
page size.

Also remove the incorrect mm_to_dma_pfn() when intel_map_sg() calls
domain_sg_mapping() -- the 'size' variable is in VT-d pages already.

Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 drivers/pci/intel-iommu.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/pci/intel-iommu.c b/drivers/pci/intel-iommu.c
index ebc9b8dca88..11b317a78b4 100644
--- a/drivers/pci/intel-iommu.c
+++ b/drivers/pci/intel-iommu.c
@@ -1648,6 +1648,14 @@ static int domain_context_mapped(struct pci_dev *pdev)
 					     tmp->devfn);
 }
 
+/* Returns a number of VTD pages, but aligned to MM page size */
+static inline unsigned long aligned_nrpages(unsigned long host_addr,
+					    size_t size)
+{
+	host_addr &= ~PAGE_MASK;
+	return PAGE_ALIGN(host_addr + size) >> VTD_PAGE_SHIFT;
+}
+
 static int __domain_mapping(struct dmar_domain *domain, unsigned long iov_pfn,
 			    struct scatterlist *sg, unsigned long phys_pfn,
 			    unsigned long nr_pages, int prot)
@@ -1675,7 +1683,7 @@ static int __domain_mapping(struct dmar_domain *domain, unsigned long iov_pfn,
 		uint64_t tmp;
 
 		if (!sg_res) {
-			sg_res = (sg->offset + sg->length + VTD_PAGE_SIZE - 1) >> VTD_PAGE_SHIFT;
+			sg_res = aligned_nrpages(sg->offset, sg->length);
 			sg->dma_address = ((dma_addr_t)iov_pfn << VTD_PAGE_SHIFT) + sg->offset;
 			sg->dma_length = sg->length;
 			pteval = page_to_phys(sg_page(sg)) | prot;
@@ -2415,14 +2423,6 @@ error:
 	return ret;
 }
 
-/* Returns a number of VTD pages, but aligned to MM page size */
-static inline unsigned long aligned_nrpages(unsigned long host_addr,
-					    size_t size)
-{
-	host_addr &= ~PAGE_MASK;
-	return PAGE_ALIGN(host_addr + size) >> VTD_PAGE_SHIFT;
-}
-
 /* This takes a number of _MM_ pages, not VTD pages */
 static struct iova *intel_alloc_iova(struct device *dev,
 				     struct dmar_domain *domain,
@@ -2875,7 +2875,7 @@ static int intel_map_sg(struct device *hwdev, struct scatterlist *sglist, int ne
 
 	start_vpfn = mm_to_dma_pfn(iova->pfn_lo);
 
-	ret = domain_sg_mapping(domain, start_vpfn, sglist, mm_to_dma_pfn(size), prot);
+	ret = domain_sg_mapping(domain, start_vpfn, sglist, size, prot);
 	if (unlikely(ret)) {
 		/*  clear the page */
 		dma_pte_clear_range(domain, start_vpfn,
-- 
GitLab


From 33041ec049d39a6e0463c7edc7b6f631d24559e3 Mon Sep 17 00:00:00 2001
From: Fenghua Yu <fenghua.yu@intel.com>
Date: Tue, 4 Aug 2009 15:10:59 -0700
Subject: [PATCH 0553/1153] intel-iommu: Mask physical address to correct page
 size in intel_map_single()

The physical address passed to domain_pfn_mapping() should be rounded
down to the start of the MM page, not the VT-d page.

This issue causes kernel panic on PAGE_SIZE>VTD_PAGE_SIZE platforms e.g. ia64
platforms.

Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 drivers/pci/intel-iommu.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/intel-iommu.c b/drivers/pci/intel-iommu.c
index 11b317a78b4..af7ff9b5aed 100644
--- a/drivers/pci/intel-iommu.c
+++ b/drivers/pci/intel-iommu.c
@@ -2551,6 +2551,7 @@ static dma_addr_t __intel_map_single(struct device *hwdev, phys_addr_t paddr,
 	int prot = 0;
 	int ret;
 	struct intel_iommu *iommu;
+	unsigned long paddr_pfn = paddr >> PAGE_SHIFT;
 
 	BUG_ON(dir == DMA_NONE);
 
@@ -2585,7 +2586,7 @@ static dma_addr_t __intel_map_single(struct device *hwdev, phys_addr_t paddr,
 	 * is not a big problem
 	 */
 	ret = domain_pfn_mapping(domain, mm_to_dma_pfn(iova->pfn_lo),
-				 paddr >> VTD_PAGE_SHIFT, size, prot);
+				 mm_to_dma_pfn(paddr_pfn), size, prot);
 	if (ret)
 		goto error;
 
-- 
GitLab


From 7d5b005652bc5ae3e1e0efc53fd0e25a643ec506 Mon Sep 17 00:00:00 2001
From: Alok Kataria <akataria@vmware.com>
Date: Tue, 4 Aug 2009 15:34:22 -0700
Subject: [PATCH 0554/1153] x86: Fix VMI && stack protector

With CONFIG_STACK_PROTECTOR turned on, VMI doesn't boot with
more than one processor. The problem is with the gs value not
being initialized correctly when registering the secondary
processor for VMI's case.

The patch below initializes the gs value for the AP to
__KERNEL_STACK_CANARY. Without this the secondary processor
keeps on taking a GP on every gs access.

Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: <stable@kernel.org> # for v2.6.30.x
LKML-Reference: <1249425262.18955.40.camel@ank32.eng.vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/vmi_32.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/kernel/vmi_32.c b/arch/x86/kernel/vmi_32.c
index b263423fbe2..95a7289e4b0 100644
--- a/arch/x86/kernel/vmi_32.c
+++ b/arch/x86/kernel/vmi_32.c
@@ -441,7 +441,7 @@ vmi_startup_ipi_hook(int phys_apicid, unsigned long start_eip,
 	ap.ds = __USER_DS;
 	ap.es = __USER_DS;
 	ap.fs = __KERNEL_PERCPU;
-	ap.gs = 0;
+	ap.gs = __KERNEL_STACK_CANARY;
 
 	ap.eflags = 0;
 
-- 
GitLab


From e125e7b6944898831b56739a5448e705578bf7e2 Mon Sep 17 00:00:00 2001
From: Jan Kiszka <jan.kiszka@web.de>
Date: Thu, 2 Jul 2009 21:45:47 +0200
Subject: [PATCH 0555/1153] KVM: Fix KVM_GET_MSR_INDEX_LIST

So far, KVM copied the emulated_msrs (only MSR_IA32_MISC_ENABLE) to a
wrong address in user space due to broken pointer arithmetic. This
caused subtle corruption up there (missing MSR_IA32_MISC_ENABLE had
probably no practical relevance). Moreover, the size check for the
user-provided kvm_msr_list forgot about emulated MSRs.

Cc: stable@kernel.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/x86/kvm/x86.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c
index fe5474aec41..7bc311464fa 100644
--- a/arch/x86/kvm/x86.c
+++ b/arch/x86/kvm/x86.c
@@ -1079,14 +1079,13 @@ long kvm_arch_dev_ioctl(struct file *filp,
 		if (copy_to_user(user_msr_list, &msr_list, sizeof msr_list))
 			goto out;
 		r = -E2BIG;
-		if (n < num_msrs_to_save)
+		if (n < msr_list.nmsrs)
 			goto out;
 		r = -EFAULT;
 		if (copy_to_user(user_msr_list->indices, &msrs_to_save,
 				 num_msrs_to_save * sizeof(u32)))
 			goto out;
-		if (copy_to_user(user_msr_list->indices
-				 + num_msrs_to_save * sizeof(u32),
+		if (copy_to_user(user_msr_list->indices + num_msrs_to_save,
 				 &emulated_msrs,
 				 ARRAY_SIZE(emulated_msrs) * sizeof(u32)))
 			goto out;
-- 
GitLab


From 0ff77873b1318fc2d77a85e70690d3cd6cafbd41 Mon Sep 17 00:00:00 2001
From: Marcelo Tosatti <mtosatti@redhat.com>
Date: Thu, 2 Jul 2009 20:02:15 -0300
Subject: [PATCH 0556/1153] KVM: PIT: fix kpit_elapsed division by zero

Fix division by zero triggered by latch count command on uninitialized
counter.

Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/x86/kvm/i8254.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/x86/kvm/i8254.c b/arch/x86/kvm/i8254.c
index 4d6f0d293ee..21f68e00524 100644
--- a/arch/x86/kvm/i8254.c
+++ b/arch/x86/kvm/i8254.c
@@ -104,6 +104,9 @@ static s64 __kpit_elapsed(struct kvm *kvm)
 	ktime_t remaining;
 	struct kvm_kpit_state *ps = &kvm->arch.vpit->pit_state;
 
+	if (!ps->pit_timer.period)
+		return 0;
+
 	/*
 	 * The Counter does not stop when it reaches zero. In
 	 * Modes 0, 1, 4, and 5 the Counter ``wraps around'' to
-- 
GitLab


From d6289b9365c3f622a8cfe62c4fb054bb70b5061a Mon Sep 17 00:00:00 2001
From: Marcelo Tosatti <mtosatti@redhat.com>
Date: Mon, 22 Jun 2009 15:27:56 -0300
Subject: [PATCH 0557/1153] KVM: x86: verify MTRR/PAT validity

Do not allow invalid memory types in MTRR/PAT (generating a #GP
otherwise).

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/x86/kvm/x86.c | 39 ++++++++++++++++++++++++++++++++++++++-
 1 file changed, 38 insertions(+), 1 deletion(-)

diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c
index 7bc311464fa..3d452901182 100644
--- a/arch/x86/kvm/x86.c
+++ b/arch/x86/kvm/x86.c
@@ -704,11 +704,48 @@ static bool msr_mtrr_valid(unsigned msr)
 	return false;
 }
 
+static bool valid_pat_type(unsigned t)
+{
+	return t < 8 && (1 << t) & 0xf3; /* 0, 1, 4, 5, 6, 7 */
+}
+
+static bool valid_mtrr_type(unsigned t)
+{
+	return t < 8 && (1 << t) & 0x73; /* 0, 1, 4, 5, 6 */
+}
+
+static bool mtrr_valid(struct kvm_vcpu *vcpu, u32 msr, u64 data)
+{
+	int i;
+
+	if (!msr_mtrr_valid(msr))
+		return false;
+
+	if (msr == MSR_IA32_CR_PAT) {
+		for (i = 0; i < 8; i++)
+			if (!valid_pat_type((data >> (i * 8)) & 0xff))
+				return false;
+		return true;
+	} else if (msr == MSR_MTRRdefType) {
+		if (data & ~0xcff)
+			return false;
+		return valid_mtrr_type(data & 0xff);
+	} else if (msr >= MSR_MTRRfix64K_00000 && msr <= MSR_MTRRfix4K_F8000) {
+		for (i = 0; i < 8 ; i++)
+			if (!valid_mtrr_type((data >> (i * 8)) & 0xff))
+				return false;
+		return true;
+	}
+
+	/* variable MTRRs */
+	return valid_mtrr_type(data & 0xff);
+}
+
 static int set_msr_mtrr(struct kvm_vcpu *vcpu, u32 msr, u64 data)
 {
 	u64 *p = (u64 *)&vcpu->arch.mtrr_state.fixed_ranges;
 
-	if (!msr_mtrr_valid(msr))
+	if (!mtrr_valid(vcpu, msr, data))
 		return 1;
 
 	if (msr == MSR_MTRRdefType) {
-- 
GitLab


From 4b656b1202498184a0ecef86b3b89ff613b9c6ab Mon Sep 17 00:00:00 2001
From: Marcelo Tosatti <mtosatti@redhat.com>
Date: Tue, 21 Jul 2009 12:47:45 -0300
Subject: [PATCH 0558/1153] KVM: SVM: force new asid on vcpu migration

If a migrated vcpu matches the asid_generation value of the target pcpu,
there will be no TLB flush via TLB_CONTROL_FLUSH_ALL_ASID.

The check for vcpu.cpu in pre_svm_run is meaningless since svm_vcpu_load
already updated it on schedule in.

Such vcpu will VMRUN with stale TLB entries.

Based on original patch from Joerg Roedel (http://patchwork.kernel.org/patch/10021/)

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/x86/kvm/svm.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/x86/kvm/svm.c b/arch/x86/kvm/svm.c
index 71510e07e69..b1f658ad2f0 100644
--- a/arch/x86/kvm/svm.c
+++ b/arch/x86/kvm/svm.c
@@ -711,6 +711,7 @@ static void svm_vcpu_load(struct kvm_vcpu *vcpu, int cpu)
 		svm->vmcb->control.tsc_offset += delta;
 		vcpu->cpu = cpu;
 		kvm_migrate_timers(vcpu);
+		svm->asid_generation = 0;
 	}
 
 	for (i = 0; i < NR_HOST_SAVE_USER_MSRS; i++)
@@ -1031,7 +1032,6 @@ static void new_asid(struct vcpu_svm *svm, struct svm_cpu_data *svm_data)
 		svm->vmcb->control.tlb_ctl = TLB_CONTROL_FLUSH_ALL_ASID;
 	}
 
-	svm->vcpu.cpu = svm_data->cpu;
 	svm->asid_generation = svm_data->asid_generation;
 	svm->vmcb->control.asid = svm_data->next_asid++;
 }
@@ -2300,8 +2300,8 @@ static void pre_svm_run(struct vcpu_svm *svm)
 	struct svm_cpu_data *svm_data = per_cpu(svm_data, cpu);
 
 	svm->vmcb->control.tlb_ctl = TLB_CONTROL_DO_NOTHING;
-	if (svm->vcpu.cpu != cpu ||
-	    svm->asid_generation != svm_data->asid_generation)
+	/* FIXME: handle wraparound of asid_generation */
+	if (svm->asid_generation != svm_data->asid_generation)
 		new_asid(svm, svm_data);
 }
 
-- 
GitLab


From 025dbbf36a7680bffe54d9dcbf0a8bc01a7cbd10 Mon Sep 17 00:00:00 2001
From: Marcelo Tosatti <mtosatti@redhat.com>
Date: Wed, 22 Jul 2009 13:05:49 -0300
Subject: [PATCH 0559/1153] KVM: MMU: handle n_free_mmu_pages >
 n_alloc_mmu_pages in kvm_mmu_change_mmu_pages

kvm_mmu_change_mmu_pages mishandles the case where n_alloc_mmu_pages is
smaller then n_free_mmu_pages, by not checking if the result of
the subtraction is negative.

Its a valid condition which can happen if a large number of pages has
been recently freed.

Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/x86/kvm/mmu.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/arch/x86/kvm/mmu.c b/arch/x86/kvm/mmu.c
index 7030b5f911b..49a10d00830 100644
--- a/arch/x86/kvm/mmu.c
+++ b/arch/x86/kvm/mmu.c
@@ -1407,24 +1407,25 @@ static int kvm_mmu_zap_page(struct kvm *kvm, struct kvm_mmu_page *sp)
  */
 void kvm_mmu_change_mmu_pages(struct kvm *kvm, unsigned int kvm_nr_mmu_pages)
 {
+	int used_pages;
+
+	used_pages = kvm->arch.n_alloc_mmu_pages - kvm->arch.n_free_mmu_pages;
+	used_pages = max(0, used_pages);
+
 	/*
 	 * If we set the number of mmu pages to be smaller be than the
 	 * number of actived pages , we must to free some mmu pages before we
 	 * change the value
 	 */
 
-	if ((kvm->arch.n_alloc_mmu_pages - kvm->arch.n_free_mmu_pages) >
-	    kvm_nr_mmu_pages) {
-		int n_used_mmu_pages = kvm->arch.n_alloc_mmu_pages
-				       - kvm->arch.n_free_mmu_pages;
-
-		while (n_used_mmu_pages > kvm_nr_mmu_pages) {
+	if (used_pages > kvm_nr_mmu_pages) {
+		while (used_pages > kvm_nr_mmu_pages) {
 			struct kvm_mmu_page *page;
 
 			page = container_of(kvm->arch.active_mmu_pages.prev,
 					    struct kvm_mmu_page, link);
 			kvm_mmu_zap_page(kvm, page);
-			n_used_mmu_pages--;
+			used_pages--;
 		}
 		kvm->arch.n_free_mmu_pages = 0;
 	}
-- 
GitLab


From 34f0c1ad27a74bd5eb0f99ea43ab6a4658d6419d Mon Sep 17 00:00:00 2001
From: Jan Kiszka <jan.kiszka@web.de>
Date: Wed, 22 Jul 2009 23:53:26 +0200
Subject: [PATCH 0560/1153] KVM: VMX: Fix locking order in
 handle_invalid_guest_state

Release and re-acquire preemption and IRQ lock in the same order as
vcpu_enter_guest does.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/x86/kvm/vmx.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kvm/vmx.c b/arch/x86/kvm/vmx.c
index 356a0ce85c6..6bf58c083f0 100644
--- a/arch/x86/kvm/vmx.c
+++ b/arch/x86/kvm/vmx.c
@@ -3157,8 +3157,8 @@ static void handle_invalid_guest_state(struct kvm_vcpu *vcpu,
 	struct vcpu_vmx *vmx = to_vmx(vcpu);
 	enum emulation_result err = EMULATE_DONE;
 
-	preempt_enable();
 	local_irq_enable();
+	preempt_enable();
 
 	while (!guest_state_valid(vcpu)) {
 		err = emulate_instruction(vcpu, kvm_run, 0, 0, 0);
@@ -3177,8 +3177,8 @@ static void handle_invalid_guest_state(struct kvm_vcpu *vcpu,
 			schedule();
 	}
 
-	local_irq_disable();
 	preempt_disable();
+	local_irq_disable();
 
 	vmx->invalid_state_emulation_result = err;
 }
-- 
GitLab


From 263799a3616242201e20fd2025fe84047b1379b1 Mon Sep 17 00:00:00 2001
From: Jan Kiszka <jan.kiszka@siemens.com>
Date: Tue, 21 Jul 2009 10:43:07 +0200
Subject: [PATCH 0561/1153] KVM: VMX: Fix locking imbalance on emulation
 failure

We have to disable preemption and IRQs on every exit from
handle_invalid_guest_state, otherwise we generate at least a
preempt_disable imbalance.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/x86/kvm/vmx.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/kvm/vmx.c b/arch/x86/kvm/vmx.c
index 6bf58c083f0..29f912927a5 100644
--- a/arch/x86/kvm/vmx.c
+++ b/arch/x86/kvm/vmx.c
@@ -3168,7 +3168,7 @@ static void handle_invalid_guest_state(struct kvm_vcpu *vcpu,
 
 		if (err != EMULATE_DONE) {
 			kvm_report_emulation_failure(vcpu, "emulation failure");
-			return;
+			break;
 		}
 
 		if (signal_pending(current))
-- 
GitLab


From d3bc2f91b4761a8d9f96bea167fef2f8c00dea54 Mon Sep 17 00:00:00 2001
From: Christian Borntraeger <borntraeger@de.ibm.com>
Date: Thu, 16 Jul 2009 17:17:37 +0200
Subject: [PATCH 0562/1153] KVM: s390: fix wait_queue handling

There are two waitqueues in kvm for wait handling:
vcpu->wq for virt/kvm/kvm_main.c and
vpcu->arch.local_int.wq for the s390 specific wait code.

the wait handling in kvm_s390_handle_wait was broken by using different
wait_queues for add_wait queue and remove_wait_queue.

There are two options to fix the problem:
o  move all the s390 specific code to vcpu->wq and remove
   vcpu->arch.local_int.wq
o  move all the s390 specific code to vcpu->arch.local_int.wq

This patch chooses the 2nd variant for two reasons:
o  s390 does not use kvm_vcpu_block but implements its own enabled wait
   handling.
   Having a separate wait_queue make it clear, that our wait mechanism is
   different
o  the patch is much smaller

Report-by:  Julia Lawall <julia@diku.dk>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/s390/kvm/interrupt.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/s390/kvm/interrupt.c b/arch/s390/kvm/interrupt.c
index f04f5301b1b..4d613415c43 100644
--- a/arch/s390/kvm/interrupt.c
+++ b/arch/s390/kvm/interrupt.c
@@ -386,7 +386,7 @@ no_timer:
 	}
 	__unset_cpu_idle(vcpu);
 	__set_current_state(TASK_RUNNING);
-	remove_wait_queue(&vcpu->wq, &wait);
+	remove_wait_queue(&vcpu->arch.local_int.wq, &wait);
 	spin_unlock_bh(&vcpu->arch.local_int.lock);
 	spin_unlock(&vcpu->arch.local_int.float_int->lock);
 	hrtimer_try_to_cancel(&vcpu->arch.ckc_timer);
-- 
GitLab


From 5116d8f6b977970ebefc1932c0f313163a6ec91f Mon Sep 17 00:00:00 2001
From: "Michael S. Tsirkin" <mst@redhat.com>
Date: Sun, 26 Jul 2009 17:10:01 +0300
Subject: [PATCH 0563/1153] KVM: fix ack not being delivered when msi present

kvm_notify_acked_irq does not check irq type, so that it sometimes
interprets msi vector as irq.  As a result, ack notifiers are not
called, which typially hangs the guest.  The fix is to track and
check irq type.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 include/linux/kvm_host.h | 1 +
 virt/kvm/irq_comm.c      | 4 +++-
 2 files changed, 4 insertions(+), 1 deletion(-)

diff --git a/include/linux/kvm_host.h b/include/linux/kvm_host.h
index 16713dc672e..3060bdc35ff 100644
--- a/include/linux/kvm_host.h
+++ b/include/linux/kvm_host.h
@@ -110,6 +110,7 @@ struct kvm_memory_slot {
 
 struct kvm_kernel_irq_routing_entry {
 	u32 gsi;
+	u32 type;
 	int (*set)(struct kvm_kernel_irq_routing_entry *e,
 		    struct kvm *kvm, int level);
 	union {
diff --git a/virt/kvm/irq_comm.c b/virt/kvm/irq_comm.c
index a8bd466d00c..ddc17f0e2f3 100644
--- a/virt/kvm/irq_comm.c
+++ b/virt/kvm/irq_comm.c
@@ -160,7 +160,8 @@ void kvm_notify_acked_irq(struct kvm *kvm, unsigned irqchip, unsigned pin)
 	unsigned gsi = pin;
 
 	list_for_each_entry(e, &kvm->irq_routing, link)
-		if (e->irqchip.irqchip == irqchip &&
+		if (e->type == KVM_IRQ_ROUTING_IRQCHIP &&
+		    e->irqchip.irqchip == irqchip &&
 		    e->irqchip.pin == pin) {
 			gsi = e->gsi;
 			break;
@@ -259,6 +260,7 @@ static int setup_routing_entry(struct kvm_kernel_irq_routing_entry *e,
 	int delta;
 
 	e->gsi = ue->gsi;
+	e->type = ue->type;
 	switch (ue->type) {
 	case KVM_IRQ_ROUTING_IRQCHIP:
 		delta = 0;
-- 
GitLab


From 114cfab222233f50f46d7162cf7d99fdc6c271e5 Mon Sep 17 00:00:00 2001
From: Pekka Enberg <penberg@cs.helsinki.fi>
Date: Wed, 5 Aug 2009 13:25:21 +0300
Subject: [PATCH 0564/1153] perf report: Make --sort comm,dso,symbol the
 default

If you're doing performance testing, you're interested in the
symbols anyway so lets make "--sort comm,dso,symbol" the
default sort option.

Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: acme@redhat.com
LKML-Reference: <1249467921-10450-1-git-send-email-penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-report.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index ce4f28645e6..8cb58d68a00 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -31,7 +31,7 @@
 static char		const *input_name = "perf.data";
 static char		*vmlinux = NULL;
 
-static char		default_sort_order[] = "comm,dso";
+static char		default_sort_order[] = "comm,dso,symbol";
 static char		*sort_order = default_sort_order;
 static char		*dso_list_str, *comm_list_str, *sym_list_str,
 			*col_width_list_str;
@@ -1424,7 +1424,7 @@ print_entries:
 	if (sort_order == default_sort_order &&
 			parent_pattern == default_parent_pattern) {
 		fprintf(fp, "#\n");
-		fprintf(fp, "# (For more details, try: perf report --sort comm,dso,symbol)\n");
+		fprintf(fp, "# (For a higher level overview, try: perf report --sort comm,dso)\n");
 		fprintf(fp, "#\n");
 	}
 	fprintf(fp, "\n");
-- 
GitLab


From c428dcc9b9f967945992a2f8529e8c50a31d7913 Mon Sep 17 00:00:00 2001
From: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Wed, 17 Jun 2009 15:04:19 +1000
Subject: [PATCH 0565/1153] KVM: Make KVM_HPAGES_PER_HPAGE unsigned long to
 avoid build error on powerpc

Eliminates this compiler warning:

arch/powerpc/kvm/../../../virt/kvm/kvm_main.c:1178: error: integer overflow in expression

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/powerpc/include/asm/kvm_host.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/powerpc/include/asm/kvm_host.h b/arch/powerpc/include/asm/kvm_host.h
index dfdf13c9fef..fddc3ed715f 100644
--- a/arch/powerpc/include/asm/kvm_host.h
+++ b/arch/powerpc/include/asm/kvm_host.h
@@ -34,7 +34,7 @@
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
 
 /* We don't currently support large pages. */
-#define KVM_PAGES_PER_HPAGE (1<<31)
+#define KVM_PAGES_PER_HPAGE (1UL << 31)
 
 struct kvm;
 struct kvm_run;
-- 
GitLab


From e9cbde8c158629cc96a26b2323c4a243536c1951 Mon Sep 17 00:00:00 2001
From: Avi Kivity <avi@redhat.com>
Date: Mon, 6 Jul 2009 12:49:39 +0300
Subject: [PATCH 0566/1153] KVM: ia64: fix build failures due to ia64/unsigned
 long mismatches

Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/ia64/kvm/mmio.c |  6 ++++--
 arch/ia64/kvm/vcpu.c |  6 +++---
 arch/ia64/kvm/vcpu.h | 13 +++++++------
 3 files changed, 14 insertions(+), 11 deletions(-)

diff --git a/arch/ia64/kvm/mmio.c b/arch/ia64/kvm/mmio.c
index 21f63fffc37..9bf55afd08d 100644
--- a/arch/ia64/kvm/mmio.c
+++ b/arch/ia64/kvm/mmio.c
@@ -247,7 +247,8 @@ void emulate_io_inst(struct kvm_vcpu *vcpu, u64 padr, u64 ma)
 		vcpu_get_fpreg(vcpu, inst.M9.f2, &v);
 		/* Write high word. FIXME: this is a kludge!  */
 		v.u.bits[1] &= 0x3ffff;
-		mmio_access(vcpu, padr + 8, &v.u.bits[1], 8, ma, IOREQ_WRITE);
+		mmio_access(vcpu, padr + 8, (u64 *)&v.u.bits[1], 8,
+			    ma, IOREQ_WRITE);
 		data = v.u.bits[0];
 		size = 3;
 	} else if (inst.M10.major == 7 && inst.M10.x6 == 0x3B) {
@@ -265,7 +266,8 @@ void emulate_io_inst(struct kvm_vcpu *vcpu, u64 padr, u64 ma)
 
 		/* Write high word.FIXME: this is a kludge!  */
 		v.u.bits[1] &= 0x3ffff;
-		mmio_access(vcpu, padr + 8, &v.u.bits[1], 8, ma, IOREQ_WRITE);
+		mmio_access(vcpu, padr + 8, (u64 *)&v.u.bits[1],
+			    8, ma, IOREQ_WRITE);
 		data = v.u.bits[0];
 		size = 3;
 	} else if (inst.M10.major == 7 && inst.M10.x6 == 0x31) {
diff --git a/arch/ia64/kvm/vcpu.c b/arch/ia64/kvm/vcpu.c
index 46b02cbcc87..cc406d064a0 100644
--- a/arch/ia64/kvm/vcpu.c
+++ b/arch/ia64/kvm/vcpu.c
@@ -461,7 +461,7 @@ void setreg(unsigned long regnum, unsigned long val,
 u64 vcpu_get_gr(struct kvm_vcpu *vcpu, unsigned long reg)
 {
 	struct kvm_pt_regs *regs = vcpu_regs(vcpu);
-	u64 val;
+	unsigned long val;
 
 	if (!reg)
 		return 0;
@@ -469,7 +469,7 @@ u64 vcpu_get_gr(struct kvm_vcpu *vcpu, unsigned long reg)
 	return val;
 }
 
-void vcpu_set_gr(struct kvm_vcpu *vcpu, u64 reg, u64 value, int nat)
+void vcpu_set_gr(struct kvm_vcpu *vcpu, unsigned long reg, u64 value, int nat)
 {
 	struct kvm_pt_regs *regs = vcpu_regs(vcpu);
 	long sof = (regs->cr_ifs) & 0x7f;
@@ -1072,7 +1072,7 @@ void kvm_ttag(struct kvm_vcpu *vcpu, INST64 inst)
 	vcpu_set_gr(vcpu, inst.M46.r1, tag, 0);
 }
 
-int vcpu_tpa(struct kvm_vcpu *vcpu, u64 vadr, u64 *padr)
+int vcpu_tpa(struct kvm_vcpu *vcpu, u64 vadr, unsigned long *padr)
 {
 	struct thash_data *data;
 	union ia64_isr visr, pt_isr;
diff --git a/arch/ia64/kvm/vcpu.h b/arch/ia64/kvm/vcpu.h
index 042af92ced8..360724d3ae6 100644
--- a/arch/ia64/kvm/vcpu.h
+++ b/arch/ia64/kvm/vcpu.h
@@ -686,14 +686,15 @@ static inline int highest_inservice_irq(struct kvm_vcpu *vcpu)
 	return highest_bits((int *)&(VMX(vcpu, insvc[0])));
 }
 
-extern void vcpu_get_fpreg(struct kvm_vcpu *vcpu, u64 reg,
+extern void vcpu_get_fpreg(struct kvm_vcpu *vcpu, unsigned long reg,
 					struct ia64_fpreg *val);
-extern void vcpu_set_fpreg(struct kvm_vcpu *vcpu, u64 reg,
+extern void vcpu_set_fpreg(struct kvm_vcpu *vcpu, unsigned long reg,
 					struct ia64_fpreg *val);
-extern u64 vcpu_get_gr(struct kvm_vcpu *vcpu, u64 reg);
-extern void vcpu_set_gr(struct kvm_vcpu *vcpu, u64 reg, u64 val, int nat);
-extern u64 vcpu_get_psr(struct kvm_vcpu *vcpu);
-extern void vcpu_set_psr(struct kvm_vcpu *vcpu, u64 val);
+extern u64 vcpu_get_gr(struct kvm_vcpu *vcpu, unsigned long reg);
+extern void vcpu_set_gr(struct kvm_vcpu *vcpu, unsigned long reg,
+			u64 val, int nat);
+extern unsigned long vcpu_get_psr(struct kvm_vcpu *vcpu);
+extern void vcpu_set_psr(struct kvm_vcpu *vcpu, unsigned long val);
 extern u64 vcpu_thash(struct kvm_vcpu *vcpu, u64 vadr);
 extern void vcpu_bsw0(struct kvm_vcpu *vcpu);
 extern void thash_vhpt_insert(struct kvm_vcpu *v, u64 pte,
-- 
GitLab


From 2cdbc46d7b2cb0acb68c3ecad93b000552121fa6 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Wed, 5 Aug 2009 14:05:16 +0200
Subject: [PATCH 0567/1153] perf: Auto-detect libbfd

Since the C++ demangling isn't needed for everybody and
bfd/iberty aren't widely/easily available on all machines, make
it optional.

It also allows you to forcefully disable demangling by using
NO_DEMANGLE=1 and otherwise tries to detect libbfd/libiberty
combinations that result in a compiling demangler.

Reported-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
LKML-Reference: <20090801082048.GX12579@kernel.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Makefile      | 18 +++++++++++++++++-
 tools/perf/util/symbol.c |  9 +++++++++
 2 files changed, 26 insertions(+), 1 deletion(-)

diff --git a/tools/perf/Makefile b/tools/perf/Makefile
index 4b20fa47c3a..ff905aceb4f 100644
--- a/tools/perf/Makefile
+++ b/tools/perf/Makefile
@@ -345,7 +345,6 @@ BUILTIN_OBJS += builtin-stat.o
 BUILTIN_OBJS += builtin-top.o
 
 PERFLIBS = $(LIB_FILE)
-EXTLIBS = -lbfd -liberty
 
 #
 # Platform specific tweaks
@@ -374,6 +373,23 @@ ifeq ($(uname_S),Darwin)
 	PTHREAD_LIBS =
 endif
 
+ifdef NO_DEMANGLE
+	BASIC_CFLAGS += -DNO_DEMANGLE
+else
+
+	has_bfd := $(shell sh -c "(echo '\#include <stdio.h>'; echo '\#include <bfd.h>'; echo '\#ifndef DMGL_PARAMS'; echo '\#define DMGL_PARAMS (1 << 0)'; echo '\#define DMGL_ANSI (1 << 1)'; echo '\#endif'; echo 'int main(int argc, char **argv) { bfd_demangle(NULL, argv[0], DMGL_PARAMS | DMGL_ANSI); return 0; }') | gcc -x c - -lbfd > /dev/null 2>&1 && echo y")
+
+	has_bfd_iberty := $(shell sh -c "(echo '\#include <stdio.h>'; echo '\#include <bfd.h>'; echo '\#ifndef DMGL_PARAMS'; echo '\#define DMGL_PARAMS (1 << 0)'; echo '\#define DMGL_ANSI (1 << 1)'; echo '\#endif'; echo 'int main(int argc, char **argv) { bfd_demangle(NULL, argv[0], DMGL_PARAMS | DMGL_ANSI); return 0; }') | gcc -x c - -lbfd -liberty > /dev/null 2>&1 && echo y")
+
+	ifeq ($(has_bfd),y)
+		EXTLIBS += -lbfd
+	else ifeq ($(has_bfd_iberty),y)
+		EXTLIBS += -lbfd -liberty
+	else
+		BASIC_CFLAGS += -DNO_DEMANGLE
+	endif
+endif
+
 ifndef CC_LD_DYNPATH
 	ifdef NO_R_TO_GCC_LINKER
 		# Some gcc does not accept and pass -R to the linker to specify
diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c
index b4fe0579bd6..0580b94785e 100644
--- a/tools/perf/util/symbol.c
+++ b/tools/perf/util/symbol.c
@@ -6,7 +6,16 @@
 #include <libelf.h>
 #include <gelf.h>
 #include <elf.h>
+
+#ifndef NO_DEMANGLE
 #include <bfd.h>
+#else
+static inline
+char *bfd_demangle(void __used *v, const char __used *c, int __used i)
+{
+	return NULL;
+}
+#endif
 
 const char *sym_hist_filter;
 
-- 
GitLab


From b37c45b8c27c049dc44673e40fd63820fd9a9d91 Mon Sep 17 00:00:00 2001
From: Roger Quadros <ext-roger.quadros@nokia.com>
Date: Wed, 5 Aug 2009 16:53:24 +0300
Subject: [PATCH 0568/1153] OMAP: GPIO: Fix incorrect gpio_get logic for output
 GPIOs

gpio_get() should return DATAIN register value when the GPIO
is configured as input whereas it should return DATAOUT register
value when the GPIO is configured as output.
Now /sys/kernel/debug/gpio shows proper values for output GPIOs

Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/plat-omap/gpio.c | 121 ++++++++++++++++++++++++++++----------
 1 file changed, 89 insertions(+), 32 deletions(-)

diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c
index 26b387c1242..9c16ca8d293 100644
--- a/arch/arm/plat-omap/gpio.c
+++ b/arch/arm/plat-omap/gpio.c
@@ -476,14 +476,12 @@ static void _set_gpio_dataout(struct gpio_bank *bank, int gpio, int enable)
 	__raw_writel(l, reg);
 }
 
-static int __omap_get_gpio_datain(int gpio)
+static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
 {
-	struct gpio_bank *bank;
 	void __iomem *reg;
 
 	if (check_gpio(gpio) < 0)
 		return -EINVAL;
-	bank = get_gpio_bank(gpio);
 	reg = bank->base;
 	switch (bank->method) {
 #ifdef CONFIG_ARCH_OMAP1
@@ -524,6 +522,53 @@ static int __omap_get_gpio_datain(int gpio)
 			& (1 << get_gpio_index(gpio))) != 0;
 }
 
+static int _get_gpio_dataout(struct gpio_bank *bank, int gpio)
+{
+	void __iomem *reg;
+
+	if (check_gpio(gpio) < 0)
+		return -EINVAL;
+	reg = bank->base;
+
+	switch (bank->method) {
+#ifdef CONFIG_ARCH_OMAP1
+	case METHOD_MPUIO:
+		reg += OMAP_MPUIO_OUTPUT;
+		break;
+#endif
+#ifdef CONFIG_ARCH_OMAP15XX
+	case METHOD_GPIO_1510:
+		reg += OMAP1510_GPIO_DATA_OUTPUT;
+		break;
+#endif
+#ifdef CONFIG_ARCH_OMAP16XX
+	case METHOD_GPIO_1610:
+		reg += OMAP1610_GPIO_DATAOUT;
+		break;
+#endif
+#ifdef CONFIG_ARCH_OMAP730
+	case METHOD_GPIO_730:
+		reg += OMAP730_GPIO_DATA_OUTPUT;
+		break;
+#endif
+#ifdef CONFIG_ARCH_OMAP850
+	case METHOD_GPIO_850:
+		reg += OMAP850_GPIO_DATA_OUTPUT;
+		break;
+#endif
+#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
+		defined(CONFIG_ARCH_OMAP4)
+	case METHOD_GPIO_24XX:
+		reg += OMAP24XX_GPIO_DATAOUT;
+		break;
+#endif
+	default:
+		return -EINVAL;
+	}
+
+	return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0;
+}
+
 #define MOD_REG_BIT(reg, bit_mask, set)	\
 do {	\
 	int l = __raw_readl(base + reg); \
@@ -1350,9 +1395,49 @@ static int gpio_input(struct gpio_chip *chip, unsigned offset)
 	return 0;
 }
 
+static int gpio_is_input(struct gpio_bank *bank, int mask)
+{
+	void __iomem *reg = bank->base;
+
+	switch (bank->method) {
+	case METHOD_MPUIO:
+		reg += OMAP_MPUIO_IO_CNTL;
+		break;
+	case METHOD_GPIO_1510:
+		reg += OMAP1510_GPIO_DIR_CONTROL;
+		break;
+	case METHOD_GPIO_1610:
+		reg += OMAP1610_GPIO_DIRECTION;
+		break;
+	case METHOD_GPIO_730:
+		reg += OMAP730_GPIO_DIR_CONTROL;
+		break;
+	case METHOD_GPIO_850:
+		reg += OMAP850_GPIO_DIR_CONTROL;
+		break;
+	case METHOD_GPIO_24XX:
+		reg += OMAP24XX_GPIO_OE;
+		break;
+	}
+	return __raw_readl(reg) & mask;
+}
+
 static int gpio_get(struct gpio_chip *chip, unsigned offset)
 {
-	return __omap_get_gpio_datain(chip->base + offset);
+	struct gpio_bank *bank;
+	void __iomem *reg;
+	int gpio;
+	u32 mask;
+
+	gpio = chip->base + offset;
+	bank = get_gpio_bank(gpio);
+	reg = bank->base;
+	mask = 1 << get_gpio_index(gpio);
+
+	if (gpio_is_input(bank, mask))
+		return _get_gpio_datain(bank, gpio);
+	else
+		return _get_gpio_dataout(bank, gpio);
 }
 
 static int gpio_output(struct gpio_chip *chip, unsigned offset, int value)
@@ -1886,34 +1971,6 @@ arch_initcall(omap_gpio_sysinit);
 #include <linux/debugfs.h>
 #include <linux/seq_file.h>
 
-static int gpio_is_input(struct gpio_bank *bank, int mask)
-{
-	void __iomem *reg = bank->base;
-
-	switch (bank->method) {
-	case METHOD_MPUIO:
-		reg += OMAP_MPUIO_IO_CNTL;
-		break;
-	case METHOD_GPIO_1510:
-		reg += OMAP1510_GPIO_DIR_CONTROL;
-		break;
-	case METHOD_GPIO_1610:
-		reg += OMAP1610_GPIO_DIRECTION;
-		break;
-	case METHOD_GPIO_730:
-		reg += OMAP730_GPIO_DIR_CONTROL;
-		break;
-	case METHOD_GPIO_850:
-		reg += OMAP850_GPIO_DIR_CONTROL;
-		break;
-	case METHOD_GPIO_24XX:
-		reg += OMAP24XX_GPIO_OE;
-		break;
-	}
-	return __raw_readl(reg) & mask;
-}
-
-
 static int dbg_gpio_show(struct seq_file *s, void *unused)
 {
 	unsigned	i, j, gpio;
-- 
GitLab


From 386c0b702b1ea81c0f54f5c9832a3d4a52270f14 Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Wed, 5 Aug 2009 10:04:53 -0300
Subject: [PATCH 0569/1153] perf report: Add missing command line options to
 man page

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20090805130453.GC10688@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Documentation/perf-record.txt | 60 ++++++++++++++++++++++--
 1 file changed, 57 insertions(+), 3 deletions(-)

diff --git a/tools/perf/Documentation/perf-record.txt b/tools/perf/Documentation/perf-record.txt
index 1dbc1eeb4c0..6be696b0a2b 100644
--- a/tools/perf/Documentation/perf-record.txt
+++ b/tools/perf/Documentation/perf-record.txt
@@ -29,13 +29,67 @@ OPTIONS
 	Select the PMU event. Selection can be a symbolic event name
 	(use 'perf list' to list all events) or a raw PMU
 	event (eventsel+umask) in the form of rNNN where NNN is a
-	 hexadecimal event descriptor.
+	hexadecimal event descriptor.
 
 -a::
-        system-wide collection
+        System-wide collection.
 
 -l::
-        scale counter values
+        Scale counter values.
+
+-p::
+--pid=::
+	Record events on existing pid.
+
+-r::
+--realtime=::
+	Collect data with this RT SCHED_FIFO priority.
+-A::
+--append::
+	Append to the output file to do incremental profiling.
+
+-f::
+--force::
+	Overwrite existing data file.
+
+-c::
+--count=::
+	Event period to sample.
+
+-o::
+--output=::
+	Output file name.
+
+-i::
+--inherit::
+	Child tasks inherit counters.
+-F::
+--freq=::
+	Profile at this frequency.
+
+-m::
+--mmap-pages=::
+	Number of mmap data pages.
+
+-g::
+--call-graph::
+	Do call-graph (stack chain/backtrace) recording.
+
+-v::
+--verbose::
+	Be more verbose (show counter open errors, etc).
+
+-s::
+--stat::
+	Per thread counts.
+
+-d::
+--data::
+	Sample addresses.
+
+-n::
+--no-samples::
+	Don't sample.
 
 SEE ALSO
 --------
-- 
GitLab


From 0bf52b981770cbf006323bab5177f2858a196766 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Tue, 4 Aug 2009 21:16:58 +0000
Subject: [PATCH 0570/1153] net: Fix spinlock use in alloc_netdev_mq()

-tip testing found this lockdep warning:

[    2.272010] calling  net_dev_init+0x0/0x164 @ 1
[    2.276033] device class 'net': registering
[    2.280191] INFO: trying to register non-static key.
[    2.284005] the code is fine but needs lockdep annotation.
[    2.284005] turning off the locking correctness validator.
[    2.284005] Pid: 1, comm: swapper Not tainted 2.6.31-rc5-tip #1145
[    2.284005] Call Trace:
[    2.284005]  [<7958eb4e>] ? printk+0xf/0x11
[    2.284005]  [<7904f83c>] __lock_acquire+0x11b/0x622
[    2.284005]  [<7908c9b7>] ? alloc_debug_processing+0xf9/0x144
[    2.284005]  [<7904e2be>] ? mark_held_locks+0x3a/0x52
[    2.284005]  [<7908dbc4>] ? kmem_cache_alloc+0xa8/0x13f
[    2.284005]  [<7904e475>] ? trace_hardirqs_on_caller+0xa2/0xc3
[    2.284005]  [<7904fdf6>] lock_acquire+0xb3/0xd0
[    2.284005]  [<79489678>] ? alloc_netdev_mq+0xf5/0x1ad
[    2.284005]  [<79591514>] _spin_lock_bh+0x2d/0x5d
[    2.284005]  [<79489678>] ? alloc_netdev_mq+0xf5/0x1ad
[    2.284005]  [<79489678>] alloc_netdev_mq+0xf5/0x1ad
[    2.284005]  [<793a38f2>] ? loopback_setup+0x0/0x74
[    2.284005]  [<798eecd0>] loopback_net_init+0x20/0x5d
[    2.284005]  [<79483efb>] register_pernet_device+0x23/0x4b
[    2.284005]  [<798f5c9f>] net_dev_init+0x115/0x164
[    2.284005]  [<7900104f>] do_one_initcall+0x4a/0x11a
[    2.284005]  [<798f5b8a>] ? net_dev_init+0x0/0x164
[    2.284005]  [<79066f6d>] ? register_irq_proc+0x8c/0xa8
[    2.284005]  [<798cc29a>] do_basic_setup+0x42/0x52
[    2.284005]  [<798cc30a>] kernel_init+0x60/0xa1
[    2.284005]  [<798cc2aa>] ? kernel_init+0x0/0xa1
[    2.284005]  [<79003e03>] kernel_thread_helper+0x7/0x10
[    2.284078] device: 'lo': device_add
[    2.288248] initcall net_dev_init+0x0/0x164 returned 0 after 11718 usecs
[    2.292010] calling  neigh_init+0x0/0x66 @ 1
[    2.296010] initcall neigh_init+0x0/0x66 returned 0 after 0 usecs

it's using an zero-initialized spinlock. This is a side-effect of:

        dev_unicast_init(dev);

in alloc_netdev_mq() making use of dev->addr_list_lock.

The device has just been allocated freshly, it's not accessible
anywhere yet so no locking is needed at all - in fact it's wrong
to lock it here (the lock isnt initialized yet).

This bug was introduced via:

| commit a6ac65db2329e7685299666f5f7b6093c7b0f3a0
| Date:   Thu Jul 30 01:06:12 2009 +0000
|
|     net: restore the original spinlock to protect unicast list

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/core/dev.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/net/core/dev.c b/net/core/dev.c
index 43e61ba7bd9..6a94475aee8 100644
--- a/net/core/dev.c
+++ b/net/core/dev.c
@@ -4007,9 +4007,7 @@ static void dev_unicast_flush(struct net_device *dev)
 
 static void dev_unicast_init(struct net_device *dev)
 {
-	netif_addr_lock_bh(dev);
 	__hw_addr_init(&dev->uc);
-	netif_addr_unlock_bh(dev);
 }
 
 
-- 
GitLab


From 7cc515f74d2871daff106a17714bfd16bcb045ca Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Wed, 10 Jun 2009 09:02:25 -0700
Subject: [PATCH 0571/1153] OMAP2/3: PM: make PM __init calls static

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/pm.h     | 3 ---
 arch/arm/mach-omap2/pm24xx.c | 2 +-
 arch/arm/mach-omap2/pm34xx.c | 2 +-
 3 files changed, 2 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h
index f7b3baf7667..21201cd4117 100644
--- a/arch/arm/mach-omap2/pm.h
+++ b/arch/arm/mach-omap2/pm.h
@@ -11,9 +11,6 @@
 #ifndef __ARCH_ARM_MACH_OMAP2_PM_H
 #define __ARCH_ARM_MACH_OMAP2_PM_H
 
-extern int omap2_pm_init(void);
-extern int omap3_pm_init(void);
-
 #ifdef CONFIG_PM_DEBUG
 extern void omap2_pm_dump(int mode, int resume, unsigned int us);
 extern int omap2_pm_debug;
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
index db1025562fb..528dbdc26e2 100644
--- a/arch/arm/mach-omap2/pm24xx.c
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -470,7 +470,7 @@ static void __init prcm_setup_regs(void)
 			  WKUP_MOD, PM_WKEN);
 }
 
-int __init omap2_pm_init(void)
+static int __init omap2_pm_init(void)
 {
 	u32 l;
 
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index 841d4c5ed8b..765cdc0cd7a 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -652,7 +652,7 @@ static int __init clkdms_setup(struct clockdomain *clkdm)
 	return 0;
 }
 
-int __init omap3_pm_init(void)
+static int __init omap3_pm_init(void)
 {
 	struct power_state *pwrst, *tmp;
 	int ret;
-- 
GitLab


From 364dd47466ff7a7749bf037df4bf3b7aedbfe6f4 Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Tue, 9 Jun 2009 11:45:30 -0700
Subject: [PATCH 0572/1153] OMAP3: PM: CM_REGADDR macros using wrong name

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/cm.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h
index 1d3c93bf86d..f3c91a1ca39 100644
--- a/arch/arm/mach-omap2/cm.h
+++ b/arch/arm/mach-omap2/cm.h
@@ -29,9 +29,9 @@
  * These registers appear once per CM module.
  */
 
-#define OMAP3430_CM_REVISION		OMAP_CM_REGADDR(OCP_MOD, 0x0000)
-#define OMAP3430_CM_SYSCONFIG		OMAP_CM_REGADDR(OCP_MOD, 0x0010)
-#define OMAP3430_CM_POLCTRL		OMAP_CM_REGADDR(OCP_MOD, 0x009c)
+#define OMAP3430_CM_REVISION		OMAP34XX_CM_REGADDR(OCP_MOD, 0x0000)
+#define OMAP3430_CM_SYSCONFIG		OMAP34XX_CM_REGADDR(OCP_MOD, 0x0010)
+#define OMAP3430_CM_POLCTRL		OMAP34XX_CM_REGADDR(OCP_MOD, 0x009c)
 
 #define OMAP3_CM_CLKOUT_CTRL_OFFSET	0x0070
 #define OMAP3430_CM_CLKOUT_CTRL		OMAP_CM_REGADDR(OMAP3430_CCR_MOD, 0x0070)
-- 
GitLab


From 3a6667acf916b3e32be4682196882fc2ed0ec23e Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Mon, 27 Apr 2009 07:50:23 -0700
Subject: [PATCH 0573/1153] OMAP3: PM: Ensure PRCM interrupts are cleared at
 boot

Any pending PRCM interrupts can prevent retention.  Ensure
they are cleared during boot.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/pm34xx.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index 765cdc0cd7a..cc83dfc39a8 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -613,6 +613,9 @@ static void __init prcm_setup_regs(void)
 	/* Clear any pending PRCM interrupts */
 	prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 
+	/* Clear any pending PRCM interrupts */
+	prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+
 	omap3_iva_idle();
 	omap3_d2d_idle();
 }
-- 
GitLab


From 3a07ae30a0bfa93ff2b242acf670c6d8e2de35de Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Mon, 27 Apr 2009 16:14:54 -0700
Subject: [PATCH 0574/1153] OMAP3: PM: Clear pending PRCM reset flags on init

Any pending reset flags can prevent retention.  Ensure they are all
cleared during boot.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/pm34xx.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index cc83dfc39a8..1422e931f57 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -613,6 +613,15 @@ static void __init prcm_setup_regs(void)
 	/* Clear any pending PRCM interrupts */
 	prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 
+	/* Clear any pending 'reset' flags */
+	prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST);
+	prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST);
+	prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, RM_RSTST);
+	prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, RM_RSTST);
+	prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, RM_RSTST);
+	prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, RM_RSTST);
+	prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, RM_RSTST);
+
 	/* Clear any pending PRCM interrupts */
 	prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 
-- 
GitLab


From 040fed059c34da5115790609f1a038fc9aec88d1 Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Tue, 5 May 2009 16:34:25 -0700
Subject: [PATCH 0575/1153] OMAP3: PM: prevent module wakeups from waking IVA2

By default, prevent functional wakeups from inside a module from
waking up the IVA2.  Let DSP Bridge code handle this when loaded.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/pm34xx.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index 1422e931f57..c813a081c3c 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -613,6 +613,12 @@ static void __init prcm_setup_regs(void)
 	/* Clear any pending PRCM interrupts */
 	prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 
+	/* Don't attach IVA interrupts */
+	prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL);
+	prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1);
+	prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3);
+	prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL);
+
 	/* Clear any pending 'reset' flags */
 	prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST);
 	prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST);
-- 
GitLab


From 10f90ed2d727c0f344d910c02c9726d0481d9b00 Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Wed, 24 Jun 2009 11:39:18 -0700
Subject: [PATCH 0576/1153] OMAP3: PM: Do not build suspend code if SUSPEND is
 not enabled

Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/pm34xx.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index c813a081c3c..528f725722a 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -39,7 +39,9 @@
 struct power_state {
 	struct powerdomain *pwrdm;
 	u32 next_state;
+#ifdef CONFIG_SUSPEND
 	u32 saved_state;
+#endif
 	struct list_head node;
 };
 
@@ -293,6 +295,7 @@ out:
 	local_irq_enable();
 }
 
+#ifdef CONFIG_SUSPEND
 static int omap3_pm_prepare(void)
 {
 	disable_hlt();
@@ -366,6 +369,7 @@ static struct platform_suspend_ops omap_pm_ops = {
 	.finish		= omap3_pm_finish,
 	.valid		= suspend_valid_only_mem,
 };
+#endif /* CONFIG_SUSPEND */
 
 
 /**
@@ -710,7 +714,9 @@ static int __init omap3_pm_init(void)
 	_omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend,
 					 omap34xx_cpu_suspend_sz);
 
+#ifdef CONFIG_SUSPEND
 	suspend_set_ops(&omap_pm_ops);
+#endif /* CONFIG_SUSPEND */
 
 	pm_idle = omap3_pm_idle;
 
-- 
GitLab


From 4789998a30d845d94a7595076d1392ffd5a9d39e Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Wed, 24 Jun 2009 10:32:03 -0700
Subject: [PATCH 0577/1153] OMAP4: UART: cleanup special case IRQ handling

Streamline the OMAP4 special IRQ assignments by putting inside
normal init loop instead of having a separate loop.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/serial.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index b094c15bfe4..c82ec95cd79 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -496,10 +496,6 @@ void __init omap_serial_init(void)
 
 	if (info == NULL)
 		return;
-	if (cpu_is_omap44xx()) {
-		for (i = 0; i < OMAP_MAX_NR_PORTS; i++)
-			serial_platform_data[i].irq += 32;
-	}
 
 	for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
 		struct plat_serial8250_port *p = serial_platform_data + i;
@@ -533,6 +529,9 @@ void __init omap_serial_init(void)
 		uart->p = p;
 		list_add(&uart->node, &uart_list);
 
+		if (cpu_is_omap44xx())
+			p->irq += 32;
+
 		omap_uart_enable_clocks(uart);
 		omap_uart_reset(uart);
 		omap_uart_idle_init(uart);
-- 
GitLab


From 2466211e5debd205fc550d871fe0ab9b9a6d02ed Mon Sep 17 00:00:00 2001
From: Tero Kristo <tero.kristo@nokia.com>
Date: Thu, 5 Mar 2009 16:32:23 +0200
Subject: [PATCH 0578/1153] OMAP3: Fixed crash bug with serial + suspend

It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.

Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path.  Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/pm34xx.c             | 23 +++++++++++++++++++++--
 arch/arm/mach-omap2/serial.c             | 14 ++++++++++++++
 arch/arm/plat-omap/include/mach/serial.h |  1 +
 3 files changed, 36 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index 528f725722a..b07efb26de1 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -296,6 +296,8 @@ out:
 }
 
 #ifdef CONFIG_SUSPEND
+static suspend_state_t suspend_state;
+
 static int omap3_pm_prepare(void)
 {
 	disable_hlt();
@@ -342,11 +344,11 @@ restore:
 	return ret;
 }
 
-static int omap3_pm_enter(suspend_state_t state)
+static int omap3_pm_enter(suspend_state_t unused)
 {
 	int ret = 0;
 
-	switch (state) {
+	switch (suspend_state) {
 	case PM_SUSPEND_STANDBY:
 	case PM_SUSPEND_MEM:
 		ret = omap3_pm_suspend();
@@ -363,7 +365,24 @@ static void omap3_pm_finish(void)
 	enable_hlt();
 }
 
+/* Hooks to enable / disable UART interrupts during suspend */
+static int omap3_pm_begin(suspend_state_t state)
+{
+	suspend_state = state;
+	omap_uart_enable_irqs(0);
+	return 0;
+}
+
+static void omap3_pm_end(void)
+{
+	suspend_state = PM_SUSPEND_ON;
+	omap_uart_enable_irqs(1);
+	return;
+}
+
 static struct platform_suspend_ops omap_pm_ops = {
+	.begin		= omap3_pm_begin,
+	.end		= omap3_pm_end,
 	.prepare	= omap3_pm_prepare,
 	.enter		= omap3_pm_enter,
 	.finish		= omap3_pm_finish,
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index c82ec95cd79..5352d05b42d 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -435,6 +435,20 @@ static void omap_uart_idle_init(struct omap_uart_state *uart)
 	WARN_ON(ret);
 }
 
+void omap_uart_enable_irqs(int enable)
+{
+	int ret;
+	struct omap_uart_state *uart;
+
+	list_for_each_entry(uart, &uart_list, node) {
+		if (enable)
+			ret = request_irq(uart->p->irq, omap_uart_interrupt,
+				IRQF_SHARED, "serial idle", (void *)uart);
+		else
+			free_irq(uart->p->irq, (void *)uart);
+	}
+}
+
 static ssize_t sleep_timeout_show(struct kobject *kobj,
 				  struct kobj_attribute *attr,
 				  char *buf)
diff --git a/arch/arm/plat-omap/include/mach/serial.h b/arch/arm/plat-omap/include/mach/serial.h
index 13abd02d152..def0529c75e 100644
--- a/arch/arm/plat-omap/include/mach/serial.h
+++ b/arch/arm/plat-omap/include/mach/serial.h
@@ -59,6 +59,7 @@ extern void omap_uart_check_wakeup(void);
 extern void omap_uart_prepare_suspend(void);
 extern void omap_uart_prepare_idle(int num);
 extern void omap_uart_resume_idle(int num);
+extern void omap_uart_enable_irqs(int enable);
 #endif
 
 #endif
-- 
GitLab


From fd455ea899b5a14a8cdd276e15f3b47696526f92 Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Mon, 27 Apr 2009 12:27:36 -0700
Subject: [PATCH 0579/1153] OMAP2/3/4: UART: Allow per-UART disabling wakeup
 for serial ports

This patch causes the OMAP uarts to honor the sysfs power/wakeup file
for IOPAD wakeups. Before the OMAP was always woken up from off mode
on a rs232 signal change.  This patch also creates a different
platform device for each serial port so that the wakeup properties can
be control per port.

By default, IOPAD wakeups are enabled for each UART.  To disable,

  # echo disabled > /sys/devices/platform/serial8250.0/power/wakeup

Where serial8250.0 can be replaced by .1, or .2 to control the other
ports.

Original idea and original patch from Russ Dill <russ.dill@gmail.com>

Cc: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/serial.c | 174 +++++++++++++++++++++++------------
 1 file changed, 116 insertions(+), 58 deletions(-)

diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 5352d05b42d..6f35a7e4893 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -54,6 +54,7 @@ struct omap_uart_state {
 
 	struct plat_serial8250_port *p;
 	struct list_head node;
+	struct platform_device pdev;
 
 #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
 	int context_valid;
@@ -68,10 +69,9 @@ struct omap_uart_state {
 #endif
 };
 
-static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS];
 static LIST_HEAD(uart_list);
 
-static struct plat_serial8250_port serial_platform_data[] = {
+static struct plat_serial8250_port serial_platform_data0[] = {
 	{
 		.membase	= IO_ADDRESS(OMAP_UART1_BASE),
 		.mapbase	= OMAP_UART1_BASE,
@@ -81,6 +81,12 @@ static struct plat_serial8250_port serial_platform_data[] = {
 		.regshift	= 2,
 		.uartclk	= OMAP24XX_BASE_BAUD * 16,
 	}, {
+		.flags		= 0
+	}
+};
+
+static struct plat_serial8250_port serial_platform_data1[] = {
+	{
 		.membase	= IO_ADDRESS(OMAP_UART2_BASE),
 		.mapbase	= OMAP_UART2_BASE,
 		.irq		= 73,
@@ -89,6 +95,12 @@ static struct plat_serial8250_port serial_platform_data[] = {
 		.regshift	= 2,
 		.uartclk	= OMAP24XX_BASE_BAUD * 16,
 	}, {
+		.flags		= 0
+	}
+};
+
+static struct plat_serial8250_port serial_platform_data2[] = {
+	{
 		.membase	= IO_ADDRESS(OMAP_UART3_BASE),
 		.mapbase	= OMAP_UART3_BASE,
 		.irq		= 74,
@@ -217,6 +229,40 @@ static inline void omap_uart_disable_clocks(struct omap_uart_state *uart)
 	clk_disable(uart->fck);
 }
 
+static void omap_uart_enable_wakeup(struct omap_uart_state *uart)
+{
+	/* Set wake-enable bit */
+	if (uart->wk_en && uart->wk_mask) {
+		u32 v = __raw_readl(uart->wk_en);
+		v |= uart->wk_mask;
+		__raw_writel(v, uart->wk_en);
+	}
+
+	/* Ensure IOPAD wake-enables are set */
+	if (cpu_is_omap34xx() && uart->padconf) {
+		u16 v = omap_ctrl_readw(uart->padconf);
+		v |= OMAP3_PADCONF_WAKEUPENABLE0;
+		omap_ctrl_writew(v, uart->padconf);
+	}
+}
+
+static void omap_uart_disable_wakeup(struct omap_uart_state *uart)
+{
+	/* Clear wake-enable bit */
+	if (uart->wk_en && uart->wk_mask) {
+		u32 v = __raw_readl(uart->wk_en);
+		v &= ~uart->wk_mask;
+		__raw_writel(v, uart->wk_en);
+	}
+
+	/* Ensure IOPAD wake-enables are cleared */
+	if (cpu_is_omap34xx() && uart->padconf) {
+		u16 v = omap_ctrl_readw(uart->padconf);
+		v &= ~OMAP3_PADCONF_WAKEUPENABLE0;
+		omap_ctrl_writew(v, uart->padconf);
+	}
+}
+
 static void omap_uart_smart_idle_enable(struct omap_uart_state *uart,
 					  int enable)
 {
@@ -246,6 +292,11 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart)
 
 static void omap_uart_allow_sleep(struct omap_uart_state *uart)
 {
+	if (device_may_wakeup(&uart->pdev.dev))
+		omap_uart_enable_wakeup(uart);
+	else
+		omap_uart_disable_wakeup(uart);
+
 	if (!uart->clocked)
 		return;
 
@@ -292,7 +343,6 @@ void omap_uart_resume_idle(int num)
 			/* Check for normal UART wakeup */
 			if (__raw_readl(uart->wk_st) & uart->wk_mask)
 				omap_uart_block_sleep(uart);
-
 			return;
 		}
 	}
@@ -346,16 +396,13 @@ static irqreturn_t omap_uart_interrupt(int irq, void *dev_id)
 	return IRQ_NONE;
 }
 
-static u32 sleep_timeout = DEFAULT_TIMEOUT;
-
 static void omap_uart_idle_init(struct omap_uart_state *uart)
 {
-	u32 v;
 	struct plat_serial8250_port *p = uart->p;
 	int ret;
 
 	uart->can_sleep = 0;
-	uart->timeout = sleep_timeout;
+	uart->timeout = DEFAULT_TIMEOUT;
 	setup_timer(&uart->timer, omap_uart_idle_timer,
 		    (unsigned long) uart);
 	mod_timer(&uart->timer, jiffies + uart->timeout);
@@ -413,22 +460,6 @@ static void omap_uart_idle_init(struct omap_uart_state *uart)
 		uart->padconf = 0;
 	}
 
-	/* Set wake-enable bit */
-	if (uart->wk_en && uart->wk_mask) {
-		v = __raw_readl(uart->wk_en);
-		v |= uart->wk_mask;
-		__raw_writel(v, uart->wk_en);
-	}
-
-	/* Ensure IOPAD wake-enables are set */
-	if (cpu_is_omap34xx() && uart->padconf) {
-		u16 v;
-
-		v = omap_ctrl_readw(uart->padconf);
-		v |= OMAP3_PADCONF_WAKEUPENABLE0;
-		omap_ctrl_writew(v, uart->padconf);
-	}
-
 	p->flags |= UPF_SHARE_IRQ;
 	ret = request_irq(p->irq, omap_uart_interrupt, IRQF_SHARED,
 			  "serial idle", (void *)uart);
@@ -449,54 +480,81 @@ void omap_uart_enable_irqs(int enable)
 	}
 }
 
-static ssize_t sleep_timeout_show(struct kobject *kobj,
-				  struct kobj_attribute *attr,
+static ssize_t sleep_timeout_show(struct device *dev,
+				  struct device_attribute *attr,
 				  char *buf)
 {
-	return sprintf(buf, "%u\n", sleep_timeout / HZ);
+	struct platform_device *pdev = container_of(dev,
+					struct platform_device, dev);
+	struct omap_uart_state *uart = container_of(pdev,
+					struct omap_uart_state, pdev);
+
+	return sprintf(buf, "%u\n", uart->timeout / HZ);
 }
 
-static ssize_t sleep_timeout_store(struct kobject *kobj,
-				   struct kobj_attribute *attr,
+static ssize_t sleep_timeout_store(struct device *dev,
+				   struct device_attribute *attr,
 				   const char *buf, size_t n)
 {
-	struct omap_uart_state *uart;
+	struct platform_device *pdev = container_of(dev,
+					struct platform_device, dev);
+	struct omap_uart_state *uart = container_of(pdev,
+					struct omap_uart_state, pdev);
 	unsigned int value;
 
 	if (sscanf(buf, "%u", &value) != 1) {
 		printk(KERN_ERR "sleep_timeout_store: Invalid value\n");
 		return -EINVAL;
 	}
-	sleep_timeout = value * HZ;
-	list_for_each_entry(uart, &uart_list, node) {
-		uart->timeout = sleep_timeout;
-		if (uart->timeout)
-			mod_timer(&uart->timer, jiffies + uart->timeout);
-		else
-			/* A zero value means disable timeout feature */
-			omap_uart_block_sleep(uart);
-	}
+
+	uart->timeout = value * HZ;
+	if (uart->timeout)
+		mod_timer(&uart->timer, jiffies + uart->timeout);
+	else
+		/* A zero value means disable timeout feature */
+		omap_uart_block_sleep(uart);
+
 	return n;
 }
 
-static struct kobj_attribute sleep_timeout_attr =
-	__ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
-
+DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store);
+#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr))
 #else
 static inline void omap_uart_idle_init(struct omap_uart_state *uart) {}
+#define DEV_CREATE_FILE(dev, attr)
 #endif /* CONFIG_PM */
 
-static struct platform_device serial_device = {
-	.name			= "serial8250",
-	.id			= PLAT8250_DEV_PLATFORM,
-	.dev			= {
-		.platform_data	= serial_platform_data,
+static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = {
+	{
+		.pdev = {
+			.name			= "serial8250",
+			.id			= PLAT8250_DEV_PLATFORM,
+			.dev			= {
+				.platform_data	= serial_platform_data0,
+			},
+		},
+	}, {
+		.pdev = {
+			.name			= "serial8250",
+			.id			= PLAT8250_DEV_PLATFORM1,
+			.dev			= {
+				.platform_data	= serial_platform_data1,
+			},
+		},
+	}, {
+		.pdev = {
+			.name			= "serial8250",
+			.id			= PLAT8250_DEV_PLATFORM2,
+			.dev			= {
+				.platform_data	= serial_platform_data2,
+			},
+		},
 	},
 };
 
 void __init omap_serial_init(void)
 {
-	int i, err;
+	int i;
 	const struct omap_uart_config *info;
 	char name[16];
 
@@ -512,8 +570,10 @@ void __init omap_serial_init(void)
 		return;
 
 	for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
-		struct plat_serial8250_port *p = serial_platform_data + i;
 		struct omap_uart_state *uart = &omap_uart[i];
+		struct platform_device *pdev = &uart->pdev;
+		struct device *dev = &pdev->dev;
+		struct plat_serial8250_port *p = dev->platform_data;
 
 		if (!(info->enabled_uarts & (1 << i))) {
 			p->membase = NULL;
@@ -549,15 +609,13 @@ void __init omap_serial_init(void)
 		omap_uart_enable_clocks(uart);
 		omap_uart_reset(uart);
 		omap_uart_idle_init(uart);
-	}
-
-	err = platform_device_register(&serial_device);
-
-#ifdef CONFIG_PM
-	if (!err)
-		err = sysfs_create_file(&serial_device.dev.kobj,
-					&sleep_timeout_attr.attr);
-#endif
 
+		if (WARN_ON(platform_device_register(pdev)))
+			continue;
+		if ((cpu_is_omap34xx() && uart->padconf) ||
+		    (uart->wk_en && uart->wk_mask)) {
+			device_init_wakeup(dev, true);
+			DEV_CREATE_FILE(dev, &dev_attr_sleep_timeout);
+		}
+	}
 }
-
-- 
GitLab


From bcf396c48012a5e4c7ab77be5c40df10d6bdb8ad Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Tue, 30 Jun 2009 21:02:45 -0700
Subject: [PATCH 0580/1153] OMAP2/3/4: UART: allow in-order port traversal

Use list_add_tail() when adding discovered UART ports.  This is so
traversal using list_for_each_entry() will traverse the list in the
order they were found.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/serial.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index 6f35a7e4893..a7421a50410 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -601,7 +601,7 @@ void __init omap_serial_init(void)
 		uart->num = i;
 		p->private_data = uart;
 		uart->p = p;
-		list_add(&uart->node, &uart_list);
+		list_add_tail(&uart->node, &uart_list);
 
 		if (cpu_is_omap44xx())
 			p->irq += 32;
-- 
GitLab


From 60c45ae1107c4ec47d2c84e5984ea59d02b2863d Mon Sep 17 00:00:00 2001
From: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Date: Tue, 23 Jun 2009 12:53:29 +0300
Subject: [PATCH 0581/1153] OMAP: PM: CPUfreq: obey min/max settings of policy

Use the min/max settings from CPUfreq policy rather than
processor defined min/max settings.

Without this patch, it's possible to scale frequency outside
the current policy range.

Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/plat-omap/cpu-omap.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/plat-omap/cpu-omap.c b/arch/arm/plat-omap/cpu-omap.c
index 843e8af6406..1868c0d8f9b 100644
--- a/arch/arm/plat-omap/cpu-omap.c
+++ b/arch/arm/plat-omap/cpu-omap.c
@@ -78,10 +78,10 @@ static int omap_target(struct cpufreq_policy *policy,
 
 	/* Ensure desired rate is within allowed range.  Some govenors
 	 * (ondemand) will just pass target_freq=0 to get the minimum. */
-	if (target_freq < policy->cpuinfo.min_freq)
-		target_freq = policy->cpuinfo.min_freq;
-	if (target_freq > policy->cpuinfo.max_freq)
-		target_freq = policy->cpuinfo.max_freq;
+	if (target_freq < policy->min)
+		target_freq = policy->min;
+	if (target_freq > policy->max)
+		target_freq = policy->max;
 
 	freqs.old = omap_getspeed(0);
 	freqs.new = clk_round_rate(mpu_clk, target_freq * 1000) / 1000;
-- 
GitLab


From 6c5f80393b107b0c9e2a54b03b65d1880e706655 Mon Sep 17 00:00:00 2001
From: Jouni Hogander <jouni.hogander@nokia.com>
Date: Wed, 29 Oct 2008 12:06:04 +0200
Subject: [PATCH 0582/1153] OMAP3: PM: Fix wrong sequence in suspend.

Powerdomain previous state is checked after restoring new states in
suspend. This patch fixes this problem.

Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/pm34xx.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index b07efb26de1..488d595d8e4 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -326,7 +326,6 @@ static int omap3_pm_suspend(void)
 restore:
 	/* Restore next_pwrsts */
 	list_for_each_entry(pwrst, &pwrst_list, node) {
-		set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
 		state = pwrdm_read_prev_pwrst(pwrst->pwrdm);
 		if (state > pwrst->next_state) {
 			printk(KERN_INFO "Powerdomain (%s) didn't enter "
@@ -334,6 +333,7 @@ restore:
 			       pwrst->pwrdm->name, pwrst->next_state);
 			ret = -1;
 		}
+		set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
 	}
 	if (ret)
 		printk(KERN_ERR "Could not enter target state in pm_suspend\n");
-- 
GitLab


From 55b6019ae29456e0f1e4087546bf4221c48622a0 Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Thu, 4 Jun 2009 15:57:10 -0700
Subject: [PATCH 0583/1153] OMAP: GPIO: clear/restore level/edge detect
 settings on mask/unmask

If IRQ triggering is enabled, it can trigger a pending interrupt
even for masked interrupts.  Any pending GPIO interrupts can
prevent the powerdomain from hitting retention.

Problem found, reported and additional review and testing by Chunquiu
Wang.

Tested-by: Chunquiu Wang <cqwang@motorola.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/plat-omap/gpio.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c
index 26b387c1242..77bad14633e 100644
--- a/arch/arm/plat-omap/gpio.c
+++ b/arch/arm/plat-omap/gpio.c
@@ -1189,6 +1189,7 @@ static void gpio_mask_irq(unsigned int irq)
 	struct gpio_bank *bank = get_irq_chip_data(irq);
 
 	_set_gpio_irqenable(bank, gpio, 0);
+	_set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE);
 }
 
 static void gpio_unmask_irq(unsigned int irq)
@@ -1196,6 +1197,11 @@ static void gpio_unmask_irq(unsigned int irq)
 	unsigned int gpio = irq - IH_GPIO_BASE;
 	struct gpio_bank *bank = get_irq_chip_data(irq);
 	unsigned int irq_mask = 1 << get_gpio_index(gpio);
+	struct irq_desc *desc = irq_to_desc(irq);
+	u32 trigger = desc->status & IRQ_TYPE_SENSE_MASK;
+
+	if (trigger)
+		_set_gpio_triggering(bank, get_gpio_index(gpio), trigger);
 
 	/* For level-triggered GPIOs, the clearing must be done after
 	 * the HW source is cleared, thus after the handler has run */
-- 
GitLab


From 6fd210a9cc398ecbff7bcdbe220651b73b654f56 Mon Sep 17 00:00:00 2001
From: Kevin Hilman <khilman@deeprootsystems.com>
Date: Mon, 20 Jul 2009 09:09:23 -0700
Subject: [PATCH 0584/1153] OMAP3: Overo: add missing pen-down GPIO definition

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-omap2/board-overo.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index dff5528fbfb..e26af837510 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -51,6 +51,7 @@
 
 #define OVERO_GPIO_BT_XGATE	15
 #define OVERO_GPIO_W2W_NRESET	16
+#define OVERO_GPIO_PENDOWN	114
 #define OVERO_GPIO_BT_NRESET	164
 #define OVERO_GPIO_USBH_CPEN	168
 #define OVERO_GPIO_USBH_NRESET	183
-- 
GitLab


From f60f785679b507cbeeb03d2db080ab649ac86027 Mon Sep 17 00:00:00 2001
From: Dhananjay Phadke <dhananjay@netxen.com>
Date: Tue, 4 Aug 2009 10:39:03 +0000
Subject: [PATCH 0585/1153] netxen: fix dma mask update calculation

Fix dma mask calculation that caps at 63-bit addressing even
when firmware advertises full 64-bit support.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/netxen/netxen_nic_main.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c
index 3cd8cfcf627..70c05c4c0ca 100644
--- a/drivers/net/netxen/netxen_nic_main.c
+++ b/drivers/net/netxen/netxen_nic_main.c
@@ -260,7 +260,7 @@ nx_update_dma_mask(struct netxen_adapter *adapter)
 	change = 0;
 
 	shift = NXRD32(adapter, CRB_DMA_SHIFT);
-	if (shift >= 32)
+	if (shift > 32)
 		return 0;
 
 	if (NX_IS_REVISION_P3(adapter->ahw.revision_id) && (shift > 9))
@@ -272,7 +272,7 @@ nx_update_dma_mask(struct netxen_adapter *adapter)
 		old_mask = pdev->dma_mask;
 		old_cmask = pdev->dev.coherent_dma_mask;
 
-		mask = (1ULL<<(32+shift)) - 1;
+		mask = DMA_BIT_MASK(32+shift);
 
 		err = pci_set_dma_mask(pdev, mask);
 		if (err)
-- 
GitLab


From 476181cb05c6a3aea3ef42309388e255c934a06f Mon Sep 17 00:00:00 2001
From: Wei Yongjun <yjwei@cn.fujitsu.com>
Date: Tue, 4 Aug 2009 21:44:39 +0000
Subject: [PATCH 0586/1153] dccp: missing destroy of percpu counter variable
 while unload module

percpu counter dccp_orphan_count is init in dccp_init() by
percpu_counter_init() while dccp module is loaded, but the
destroy of it is missing while dccp module is unloaded. We
can get the kernel WARNING about this. Reproduct by the
following commands:

  $ modprobe dccp
  $ rmmod dccp
  $ modprobe dccp

WARNING: at lib/list_debug.c:26 __list_add+0x27/0x5c()
Hardware name: VMware Virtual Platform
list_add corruption. next->prev should be prev (c080c0c4), but was (null). (next
=ca7188cc).
Modules linked in: dccp(+) nfsd lockd nfs_acl auth_rpcgss exportfs sunrpc
Pid: 1956, comm: modprobe Not tainted 2.6.31-rc5 #55
Call Trace:
 [<c042f8fa>] warn_slowpath_common+0x6a/0x81
 [<c053a6cb>] ? __list_add+0x27/0x5c
 [<c042f94f>] warn_slowpath_fmt+0x29/0x2c
 [<c053a6cb>] __list_add+0x27/0x5c
 [<c053c9b3>] __percpu_counter_init+0x4d/0x5d
 [<ca9c90c7>] dccp_init+0x19/0x2ed [dccp]
 [<c0401141>] do_one_initcall+0x4f/0x111
 [<ca9c90ae>] ? dccp_init+0x0/0x2ed [dccp]
 [<c06971b5>] ? notifier_call_chain+0x26/0x48
 [<c0444943>] ? __blocking_notifier_call_chain+0x45/0x51
 [<c04516f7>] sys_init_module+0xac/0x1bd
 [<c04028e4>] sysenter_do_call+0x12/0x22

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/dccp/proto.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/dccp/proto.c b/net/dccp/proto.c
index 94ca8eaace7..6294f57162b 100644
--- a/net/dccp/proto.c
+++ b/net/dccp/proto.c
@@ -1159,6 +1159,7 @@ static void __exit dccp_fini(void)
 	kmem_cache_destroy(dccp_hashinfo.bind_bucket_cachep);
 	dccp_ackvec_exit();
 	dccp_sysctl_exit();
+	percpu_counter_destroy(&dccp_orphan_count);
 }
 
 module_init(dccp_init);
-- 
GitLab


From 9c9fe1f841745184bbc5460c6f3909fded3b929b Mon Sep 17 00:00:00 2001
From: Eric Anholt <eric@anholt.net>
Date: Mon, 3 Aug 2009 16:09:16 -0700
Subject: [PATCH 0587/1153] drm/i915: Use our own workqueue to avoid wedging
 the system along with the GPU.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/i915_dma.c | 15 +++++++++++++--
 drivers/gpu/drm/i915/i915_drv.h |  1 +
 drivers/gpu/drm/i915/i915_gem.c |  4 ++--
 drivers/gpu/drm/i915/i915_irq.c |  5 +++--
 4 files changed, 19 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_dma.c b/drivers/gpu/drm/i915/i915_dma.c
index 8c4783180bf..50d1f782768 100644
--- a/drivers/gpu/drm/i915/i915_dma.c
+++ b/drivers/gpu/drm/i915/i915_dma.c
@@ -1186,6 +1186,13 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	if (ret)
 		goto out_iomapfree;
 
+	dev_priv->wq = create_workqueue("i915");
+	if (dev_priv->wq == NULL) {
+		DRM_ERROR("Failed to create our workqueue.\n");
+		ret = -ENOMEM;
+		goto out_iomapfree;
+	}
+
 	/* enable GEM by default */
 	dev_priv->has_gem = 1;
 
@@ -1211,7 +1218,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	if (!I915_NEED_GFX_HWS(dev)) {
 		ret = i915_init_phys_hws(dev);
 		if (ret != 0)
-			goto out_iomapfree;
+			goto out_workqueue_free;
 	}
 
 	i915_get_mem_freq(dev);
@@ -1245,7 +1252,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 		ret = i915_load_modeset_init(dev, prealloc_size, agp_size);
 		if (ret < 0) {
 			DRM_ERROR("failed to init modeset\n");
-			goto out_rmmap;
+			goto out_workqueue_free;
 		}
 	}
 
@@ -1256,6 +1263,8 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 
 	return 0;
 
+out_workqueue_free:
+	destroy_workqueue(dev_priv->wq);
 out_iomapfree:
 	io_mapping_free(dev_priv->mm.gtt_mapping);
 out_rmmap:
@@ -1269,6 +1278,8 @@ int i915_driver_unload(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 
+	destroy_workqueue(dev_priv->wq);
+
 	io_mapping_free(dev_priv->mm.gtt_mapping);
 	if (dev_priv->mm.gtt_mtrr >= 0) {
 		mtrr_del(dev_priv->mm.gtt_mtrr, dev->agp->base,
diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 5f3a259d95e..7537f57d8a8 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -231,6 +231,7 @@ typedef struct drm_i915_private {
 	spinlock_t error_lock;
 	struct drm_i915_error_state *first_error;
 	struct work_struct error_work;
+	struct workqueue_struct *wq;
 
 	/* Register state */
 	u8 saveLBB;
diff --git a/drivers/gpu/drm/i915/i915_gem.c b/drivers/gpu/drm/i915/i915_gem.c
index 5bf420378b6..140bee142fc 100644
--- a/drivers/gpu/drm/i915/i915_gem.c
+++ b/drivers/gpu/drm/i915/i915_gem.c
@@ -1570,7 +1570,7 @@ i915_add_request(struct drm_device *dev, struct drm_file *file_priv,
 	}
 
 	if (was_empty && !dev_priv->mm.suspended)
-		schedule_delayed_work(&dev_priv->mm.retire_work, HZ);
+		queue_delayed_work(dev_priv->wq, &dev_priv->mm.retire_work, HZ);
 	return seqno;
 }
 
@@ -1719,7 +1719,7 @@ i915_gem_retire_work_handler(struct work_struct *work)
 	i915_gem_retire_requests(dev);
 	if (!dev_priv->mm.suspended &&
 	    !list_empty(&dev_priv->mm.request_list))
-		schedule_delayed_work(&dev_priv->mm.retire_work, HZ);
+		queue_delayed_work(dev_priv->wq, &dev_priv->mm.retire_work, HZ);
 	mutex_unlock(&dev->struct_mutex);
 }
 
diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index f340b3fd54e..83aee80e77a 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -482,7 +482,7 @@ static void i915_handle_error(struct drm_device *dev)
 		I915_WRITE(IIR, I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT);
 	}
 
-	schedule_work(&dev_priv->error_work);
+	queue_work(dev_priv->wq, &dev_priv->error_work);
 }
 
 irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
@@ -560,7 +560,8 @@ irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
 			DRM_DEBUG("hotplug event received, stat 0x%08x\n",
 				  hotplug_status);
 			if (hotplug_status & dev_priv->hotplug_supported_mask)
-				schedule_work(&dev_priv->hotplug_work);
+				queue_work(dev_priv->wq,
+					   &dev_priv->hotplug_work);
 
 			I915_WRITE(PORT_HOTPLUG_STAT, hotplug_status);
 			I915_READ(PORT_HOTPLUG_STAT);
-- 
GitLab


From 819e0064634f580ab618189e657ea58341d214b7 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Sun, 26 Jul 2009 00:50:38 +0200
Subject: [PATCH 0588/1153] drm/i915: Fix read outside array bounds in
 restoring the SWF10 range.

dev_priv->saveSWF1 is a 16 element array, but this reads up to index 22,
and restored values from the wrong registers.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/i915_suspend.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/i915/i915_suspend.c b/drivers/gpu/drm/i915/i915_suspend.c
index 9e1d16e5c3e..1d04e1904ac 100644
--- a/drivers/gpu/drm/i915/i915_suspend.c
+++ b/drivers/gpu/drm/i915/i915_suspend.c
@@ -598,7 +598,7 @@ int i915_restore_state(struct drm_device *dev)
 
 	for (i = 0; i < 16; i++) {
 		I915_WRITE(SWF00 + (i << 2), dev_priv->saveSWF0[i]);
-		I915_WRITE(SWF10 + (i << 2), dev_priv->saveSWF1[i+7]);
+		I915_WRITE(SWF10 + (i << 2), dev_priv->saveSWF1[i]);
 	}
 	for (i = 0; i < 3; i++)
 		I915_WRITE(SWF30 + (i << 2), dev_priv->saveSWF2[i]);
-- 
GitLab


From cf39c4c572dc54adbdf8933d1e6cd87ee94d8fc0 Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Mon, 27 Jul 2009 08:03:18 -0700
Subject: [PATCH 0589/1153] phonet: phonet_device_get() fix
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

net/phonet/pn_dev.c: In function `phonet_device_get':
net/phonet/pn_dev.c:99: warning: 'dev' might be used uninitialized in this function

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/phonet/pn_dev.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/phonet/pn_dev.c b/net/phonet/pn_dev.c
index b0d6ddd82a9..c2b77a69869 100644
--- a/net/phonet/pn_dev.c
+++ b/net/phonet/pn_dev.c
@@ -96,7 +96,7 @@ struct net_device *phonet_device_get(struct net *net)
 {
 	struct phonet_device_list *pndevs = phonet_device_list(net);
 	struct phonet_device *pnd;
-	struct net_device *dev;
+	struct net_device *dev = NULL;
 
 	spin_lock_bh(&pndevs->lock);
 	list_for_each_entry(pnd, &pndevs->list, list) {
-- 
GitLab


From 0a51810aa058a0a4ac76dd6f87f4d10bee774e2e Mon Sep 17 00:00:00 2001
From: Andrew Victor <linux@maxim.org.za>
Date: Tue, 4 Aug 2009 19:55:56 +0100
Subject: [PATCH 0590/1153] ARM: 5637/1: [KS8695] Don't reference
 CLOCK_TICK_RATE in drivers

Stop referencing CLOCK_TICK_RATE in the KS8695 drivers, rather refer
to a KS8695_CLOCK_RATE.
Issue pointed out by Russell King on arm-linux-kernel mailing list.

Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-ks8695/include/mach/hardware.h | 5 +++++
 arch/arm/mach-ks8695/include/mach/timex.h    | 5 +++--
 drivers/serial/serial_ks8695.c               | 2 +-
 drivers/watchdog/ks8695_wdt.c                | 4 ++--
 4 files changed, 11 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-ks8695/include/mach/hardware.h b/arch/arm/mach-ks8695/include/mach/hardware.h
index 1d640d075b7..e0f911d9e02 100644
--- a/arch/arm/mach-ks8695/include/mach/hardware.h
+++ b/arch/arm/mach-ks8695/include/mach/hardware.h
@@ -16,6 +16,11 @@
 
 #include <asm/sizes.h>
 
+/*
+ * Clocks are derived from MCLK, which is 25Mhz
+ */
+#define KS8695_CLOCK_RATE	25000000
+
 /*
  * Physical RAM address.
  */
diff --git a/arch/arm/mach-ks8695/include/mach/timex.h b/arch/arm/mach-ks8695/include/mach/timex.h
index 4682e350369..10f716371bd 100644
--- a/arch/arm/mach-ks8695/include/mach/timex.h
+++ b/arch/arm/mach-ks8695/include/mach/timex.h
@@ -14,7 +14,8 @@
 #ifndef __ASM_ARCH_TIMEX_H
 #define __ASM_ARCH_TIMEX_H
 
-/* timers are derived from MCLK, which is 25MHz */
-#define CLOCK_TICK_RATE 25000000
+#include <mach/hardware.h>
+
+#define CLOCK_TICK_RATE 	KS8695_CLOCK_RATE
 
 #endif
diff --git a/drivers/serial/serial_ks8695.c b/drivers/serial/serial_ks8695.c
index 998e89dc5aa..e0665630e4d 100644
--- a/drivers/serial/serial_ks8695.c
+++ b/drivers/serial/serial_ks8695.c
@@ -549,7 +549,7 @@ static struct uart_port ks8695uart_ports[SERIAL_KS8695_NR] = {
 		.mapbase	= KS8695_UART_VA,
 		.iotype		= SERIAL_IO_MEM,
 		.irq		= KS8695_IRQ_UART_TX,
-		.uartclk	= CLOCK_TICK_RATE * 16,
+		.uartclk	= KS8695_CLOCK_RATE * 16,
 		.fifosize	= 16,
 		.ops		= &ks8695uart_pops,
 		.flags		= ASYNC_BOOT_AUTOCONF,
diff --git a/drivers/watchdog/ks8695_wdt.c b/drivers/watchdog/ks8695_wdt.c
index 00b03eb43bf..e1c82769b08 100644
--- a/drivers/watchdog/ks8695_wdt.c
+++ b/drivers/watchdog/ks8695_wdt.c
@@ -66,7 +66,7 @@ static inline void ks8695_wdt_stop(void)
 static inline void ks8695_wdt_start(void)
 {
 	unsigned long tmcon;
-	unsigned long tval = wdt_time * CLOCK_TICK_RATE;
+	unsigned long tval = wdt_time * KS8695_CLOCK_RATE;
 
 	spin_lock(&ks8695_lock);
 	/* disable timer0 */
@@ -103,7 +103,7 @@ static inline void ks8695_wdt_reload(void)
 static int ks8695_wdt_settimeout(int new_time)
 {
 	/*
-	 * All counting occurs at SLOW_CLOCK / 128 = 0.256 Hz
+	 * All counting occurs at KS8695_CLOCK_RATE / 128 = 0.256 Hz
 	 *
 	 * Since WDV is a 16-bit counter, the maximum period is
 	 * 65536 / 0.256 = 256 seconds.
-- 
GitLab


From 65a5053b764a42d33b334ba55810bb5b56eb92df Mon Sep 17 00:00:00 2001
From: Hartley Sweeten <hartleys@visionengravers.com>
Date: Tue, 4 Aug 2009 23:20:45 +0100
Subject: [PATCH 0591/1153] ARM: 5638/1: arch/arm/kernel/signal.c: use correct
 address space for CRUNCH

preserve_crunch_context() calls __copy_to_user() which expects the
destination address to be in __user space.  setup_sigframe() properly
passes the destination address.

restore_crunch_context() calls __copy_from_user() which expects the
source address to be in __user space.  restore_sigframe() properly
passes the source address.

This fixes {preserve/restore}_crunch_context() to accept the
address as __user space and resolves the following sparse warnings:

  arch/arm/kernel/signal.c:146:31:
     warning: incorrect type in argument 1 (different address spaces)
        expected void [noderef] <asn:1>*to
        got struct crunch_sigframe *frame

  arch/arm/kernel/signal.c:156:38:
     warning: incorrect type in argument 2 (different address spaces)
        expected void const [noderef] <asn:1>*from
        got struct crunch_sigframe *frame

  arch/arm/kernel/signal.c:250:48:
     warning: incorrect type in argument 1 (different address spaces)
        expected struct crunch_sigframe *frame
        got struct crunch_sigframe [noderef] <asn:1>*<noident>

  arch/arm/kernel/signal.c:365:49:
     warning: incorrect type in argument 1 (different address spaces)
        expected struct crunch_sigframe *frame
        got struct crunch_sigframe [noderef] <asn:1>*<noident>

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/kernel/signal.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c
index 93bb4247b7e..f6bc5d44278 100644
--- a/arch/arm/kernel/signal.c
+++ b/arch/arm/kernel/signal.c
@@ -133,7 +133,7 @@ sys_sigaction(int sig, const struct old_sigaction __user *act,
 }
 
 #ifdef CONFIG_CRUNCH
-static int preserve_crunch_context(struct crunch_sigframe *frame)
+static int preserve_crunch_context(struct crunch_sigframe __user *frame)
 {
 	char kbuf[sizeof(*frame) + 8];
 	struct crunch_sigframe *kframe;
@@ -146,7 +146,7 @@ static int preserve_crunch_context(struct crunch_sigframe *frame)
 	return __copy_to_user(frame, kframe, sizeof(*frame));
 }
 
-static int restore_crunch_context(struct crunch_sigframe *frame)
+static int restore_crunch_context(struct crunch_sigframe __user *frame)
 {
 	char kbuf[sizeof(*frame) + 8];
 	struct crunch_sigframe *kframe;
-- 
GitLab


From c0c60c4b9ab45bb02b20796401dd6a90770fd0ee Mon Sep 17 00:00:00 2001
From: Hartley Sweeten <hartleys@visionengravers.com>
Date: Tue, 4 Aug 2009 23:38:06 +0100
Subject: [PATCH 0592/1153] ARM: 5639/1: arm: clkdev.c should include
 <linux/clk.h>

<linux/clk.h> should be included to get the base API prototypes.

This fixes the following sparse warnings:

  arch/arm/common/clkdev.c:65:12:
    warning: symbol 'clk_get_sys' was not declared. Should it be static?

  arch/arm/common/clkdev.c:79:12:
    warning: symbol 'clk_get' was not declared. Should it be static?

  arch/arm/common/clkdev.c:87:6:
    warning: symbol 'clk_put' was not declared. Should it be static?

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/common/clkdev.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/common/clkdev.c b/arch/arm/common/clkdev.c
index f37afd9422f..aae5bc01acc 100644
--- a/arch/arm/common/clkdev.c
+++ b/arch/arm/common/clkdev.c
@@ -17,6 +17,7 @@
 #include <linux/err.h>
 #include <linux/string.h>
 #include <linux/mutex.h>
+#include <linux/clk.h>
 
 #include <asm/clkdev.h>
 #include <mach/clkdev.h>
-- 
GitLab


From 0f2541d299d233eddddee4345795e0c46264fd56 Mon Sep 17 00:00:00 2001
From: Steven Rostedt <srostedt@redhat.com>
Date: Wed, 5 Aug 2009 12:02:48 -0400
Subject: [PATCH 0593/1153] ring-buffer: fix check of try_to_discard result

The function ring_buffer_discard_commit inversed the code path
of the result of try_to_discard. It should skip incrementing the
entry counter if try_to_discard succeeded. But instead, it increments
the entry conder if it succeeded to discard, and does not increment
it if it fails.

The result of this bug is that filtering will make the stat counters
incorrect.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 kernel/trace/ring_buffer.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c
index bf27bb7a63e..2fd1752f0c8 100644
--- a/kernel/trace/ring_buffer.c
+++ b/kernel/trace/ring_buffer.c
@@ -1785,7 +1785,7 @@ void ring_buffer_discard_commit(struct ring_buffer *buffer,
 	 */
 	RB_WARN_ON(buffer, !local_read(&cpu_buffer->committing));
 
-	if (!rb_try_to_discard(cpu_buffer, event))
+	if (rb_try_to_discard(cpu_buffer, event))
 		goto out;
 
 	/*
-- 
GitLab


From 464e85eb0e63096bd52e4c3e2a6fb8357fb95828 Mon Sep 17 00:00:00 2001
From: Steven Rostedt <srostedt@redhat.com>
Date: Wed, 5 Aug 2009 15:26:37 -0400
Subject: [PATCH 0594/1153] ring-buffer: do not disable ring buffer on
 oops_in_progress

The commit:

  commit e0fdace10e75dac67d906213b780ff1b1a4cc360
  Author: David Miller <davem@davemloft.net>
  Date:   Fri Aug 1 01:11:22 2008 -0700

    debug_locks: set oops_in_progress if we will log messages.

    Otherwise lock debugging messages on runqueue locks can deadlock the
    system due to the wakeups performed by printk().

    Signed-off-by: David S. Miller <davem@davemloft.net>
    Signed-off-by: Ingo Molnar <mingo@elte.hu>

Will permanently set oops_in_progress on any lockdep failure.
When this triggers it will cause any read from the ring buffer to
permanently disable the ring buffer (not to mention no locking of
printk).

This patch removes the check. It keeps the print in NMI which makes
sense. This is probably OK, since the ring buffer should not cause
something to set oops_in_progress anyway.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 kernel/trace/ring_buffer.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c
index 2fd1752f0c8..2606cee433d 100644
--- a/kernel/trace/ring_buffer.c
+++ b/kernel/trace/ring_buffer.c
@@ -2486,7 +2486,7 @@ static inline int rb_ok_to_lock(void)
 	 * buffer too. A one time deal is all you get from reading
 	 * the ring buffer from an NMI.
 	 */
-	if (likely(!in_nmi() && !oops_in_progress))
+	if (likely(!in_nmi()))
 		return 1;
 
 	tracing_off_permanent();
-- 
GitLab


From 3f6e968ef4e1d8d93d8a8505461b0e50a9e97ad8 Mon Sep 17 00:00:00 2001
From: Steven Rostedt <rostedt@goodmis.org>
Date: Wed, 5 Aug 2009 22:00:14 -0400
Subject: [PATCH 0595/1153] tracing: do not use functions starting with .L in
 recordmcount.pl

On Wed, 5 Aug 2009, Ingo Molnar wrote:
> * Dave Airlie <airlied@gmail.com> wrote:
>
> > Hey,
> >
> > So I spent 3-4 hrs today (I'm stupid yes) tracking down a .o
> > breakage by blaming rawhide gcc/binutils as I was using make
> > V=1and seeing only the compiler chain running,
>
> Hm, is this that powerpc related build bug you just reported?

Well we tracked it down and it is powerpc64 specific.

Seems that in drivers/hwmon/lm93.c there's a function called:

   LM93_IN_FROM_REG()

But PPC64 has function descriptors and the real function names (the ones
you see in objdump) start with a '.'. Thus this in objdump you have:

 Disassembly of section .text:

 0000000000000000 <.LM93_IN_FROM_REG>:
       0:       7c 08 02 a6     mflr    r0
       4:       fb 81 ff e0     std     r28,-32(r1)

The function name used is .LM93_IN_FROM_REG. But gcc considers symbols
that start with ".L" as a special symbol that is used inside the assembly
stage.

The nm passed into recordmcount uses the --synthetic option which shows
the ".L" symbols (my runs outside of the build did not include the
--synthetic option, so my older patch worked). We see the function as a
local.

Now to capture all the locations that use "mcount" we need to have a
reference to link into the object file a list of mcount callers. We need a
reference that will not disappear. We try to use a global function and if
that does not work, we use a local function as a reference. But to relink
the section back into the object, we need to make it global. In this case,
we run objcopy using --globalize-symbol and --localize-symbol to convert
the symbol into a global symbol, link the mcount list, then convert it
back to a local symbol.

This works great except for this case. .L* symbols can not be converted
into a global symbol, and the mcount section referencing it will remain
unresolved.

Reported-by: Dave Airlie <airlied@gmail.com>
LKML-Reference: <alpine.DEB.2.00.0908052011590.5010@gandalf.stny.rr.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 scripts/recordmcount.pl | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/scripts/recordmcount.pl b/scripts/recordmcount.pl
index d29baa2e063..4889c44d71b 100755
--- a/scripts/recordmcount.pl
+++ b/scripts/recordmcount.pl
@@ -414,7 +414,10 @@ while (<IN>) {
 	    $offset = hex $1;
 	} else {
 	    # if we already have a function, and this is weak, skip it
-	    if (!defined($ref_func) && !defined($weak{$text})) {
+	    if (!defined($ref_func) && !defined($weak{$text}) &&
+		 # PPC64 can have symbols that start with .L and
+		 # gcc considers these special. Don't use them!
+		 $text !~ /^\.L/) {
 		$ref_func = $text;
 		$offset = hex $1;
 	    }
-- 
GitLab


From b4adbb4ddf63091f48668e7ff1b9b0f6f84d4b40 Mon Sep 17 00:00:00 2001
From: Pascal Terjan <pterjan@mandriva.com>
Date: Wed, 5 Aug 2009 04:11:39 +0000
Subject: [PATCH 0596/1153] Add IDs for 3C905B-TX Fast Etherlink XL PCI

We found this old card which was not supported, and physically
looks similar to the other 3C905B we have (9055).

After adding the IDs it seems to work fine (MII report, dhcp, scp, ...)

Acked-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>

Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/3c59x.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c
index c2041685094..45675889850 100644
--- a/drivers/net/3c59x.c
+++ b/drivers/net/3c59x.c
@@ -235,6 +235,7 @@ enum vortex_chips {
 	CH_3C900B_FL,
 	CH_3C905_1,
 	CH_3C905_2,
+	CH_3C905B_TX,
 	CH_3C905B_1,
 
 	CH_3C905B_2,
@@ -307,6 +308,8 @@ static struct vortex_chip_info {
 	 PCI_USES_MASTER, IS_BOOMERANG|HAS_MII|EEPROM_RESET, 64, },
 	{"3c905 Boomerang 100baseT4",
 	 PCI_USES_MASTER, IS_BOOMERANG|HAS_MII|EEPROM_RESET, 64, },
+	{"3C905B-TX Fast Etherlink XL PCI",
+	 PCI_USES_MASTER, IS_CYCLONE|HAS_NWAY|HAS_HWCKSM|EXTRA_PREAMBLE, 128, },
 	{"3c905B Cyclone 100baseTx",
 	 PCI_USES_MASTER, IS_CYCLONE|HAS_NWAY|HAS_HWCKSM|EXTRA_PREAMBLE, 128, },
 
@@ -389,6 +392,7 @@ static struct pci_device_id vortex_pci_tbl[] = {
 	{ 0x10B7, 0x900A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C900B_FL },
 	{ 0x10B7, 0x9050, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905_1 },
 	{ 0x10B7, 0x9051, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905_2 },
+	{ 0x10B7, 0x9054, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905B_TX },
 	{ 0x10B7, 0x9055, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905B_1 },
 
 	{ 0x10B7, 0x9058, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CH_3C905B_2 },
-- 
GitLab


From 1bbf20835c4e088667a090ce6523a0f70b62dc76 Mon Sep 17 00:00:00 2001
From: Darren Hart <dvhltc@us.ibm.com>
Date: Wed, 5 Aug 2009 12:05:21 -0700
Subject: [PATCH 0597/1153] rtmutex: Avoid deadlock in
 rt_mutex_start_proxy_lock()

In the event of a lock steal or owner died,
rt_mutex_start_proxy_lock() will give the rt_mutex to the
waiting task, but it fails to release the wait_lock. This leads
to subsequent deadlocks when other tasks try to acquire the
rt_mutex.

I also removed a few extra blank lines that really spaced this
routine out. I must have been high on the \n when I wrote this
originally...

Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Dinakar Guniguntala <dino@in.ibm.com>
Cc: John Stultz <johnstul@linux.vnet.ibm.com>
LKML-Reference: <4A79D7F1.4000405@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/rtmutex.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/kernel/rtmutex.c b/kernel/rtmutex.c
index fcd107a78c5..29bd4baf9e7 100644
--- a/kernel/rtmutex.c
+++ b/kernel/rtmutex.c
@@ -1039,16 +1039,14 @@ int rt_mutex_start_proxy_lock(struct rt_mutex *lock,
 	if (!rt_mutex_owner(lock) || try_to_steal_lock(lock, task)) {
 		/* We got the lock for task. */
 		debug_rt_mutex_lock(lock);
-
 		rt_mutex_set_owner(lock, task, 0);
-
+		spin_unlock(&lock->wait_lock);
 		rt_mutex_deadlock_account_lock(lock, task);
 		return 1;
 	}
 
 	ret = task_blocks_on_rt_mutex(lock, waiter, task, detect_deadlock);
 
-
 	if (ret && !waiter->task) {
 		/*
 		 * Reset the return value. We might have
-- 
GitLab


From af6af30c0fcd77e621638e53ef8b176bca8bd3b4 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <peterz@infradead.org>
Date: Wed, 5 Aug 2009 20:41:04 +0200
Subject: [PATCH 0598/1153] ftrace: Fix perf-tracepoint OOPS

Not all tracepoints are created equal, in specific the ftrace
tracepoints are created with TRACE_EVENT_FORMAT() which does
not generate the needed bits to tie them into perf counters.

For those events, don't create the 'id' file and fail
->profile_enable when their ID is specified through other
means.

Reported-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <1249497664.5890.4.camel@laptop>
[ v2: fix build error in the !CONFIG_EVENT_PROFILE case ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 include/linux/ftrace_event.h       | 8 +++-----
 kernel/trace/trace_event_profile.c | 2 +-
 kernel/trace/trace_events.c        | 2 +-
 3 files changed, 5 insertions(+), 7 deletions(-)

diff --git a/include/linux/ftrace_event.h b/include/linux/ftrace_event.h
index 5c093ffc655..d7cd193c227 100644
--- a/include/linux/ftrace_event.h
+++ b/include/linux/ftrace_event.h
@@ -119,11 +119,9 @@ struct ftrace_event_call {
 	void			*filter;
 	void			*mod;
 
-#ifdef CONFIG_EVENT_PROFILE
-	atomic_t	profile_count;
-	int		(*profile_enable)(struct ftrace_event_call *);
-	void		(*profile_disable)(struct ftrace_event_call *);
-#endif
+	atomic_t		profile_count;
+	int			(*profile_enable)(struct ftrace_event_call *);
+	void			(*profile_disable)(struct ftrace_event_call *);
 };
 
 #define MAX_FILTER_PRED		32
diff --git a/kernel/trace/trace_event_profile.c b/kernel/trace/trace_event_profile.c
index 5b5895afecf..11ba5bb4ed0 100644
--- a/kernel/trace/trace_event_profile.c
+++ b/kernel/trace/trace_event_profile.c
@@ -14,7 +14,7 @@ int ftrace_profile_enable(int event_id)
 
 	mutex_lock(&event_mutex);
 	list_for_each_entry(event, &ftrace_events, list) {
-		if (event->id == event_id) {
+		if (event->id == event_id && event->profile_enable) {
 			ret = event->profile_enable(event);
 			break;
 		}
diff --git a/kernel/trace/trace_events.c b/kernel/trace/trace_events.c
index 23d2972b22d..e75276a49cf 100644
--- a/kernel/trace/trace_events.c
+++ b/kernel/trace/trace_events.c
@@ -940,7 +940,7 @@ event_create_dir(struct ftrace_event_call *call, struct dentry *d_events,
 		entry = trace_create_file("enable", 0644, call->dir, call,
 					  enable);
 
-	if (call->id)
+	if (call->id && call->profile_enable)
 		entry = trace_create_file("id", 0444, call->dir, call,
 					  id);
 
-- 
GitLab


From 985fe845aea9cd56fd351800302270444556e45a Mon Sep 17 00:00:00 2001
From: Jerome Glisse <jglisse@redhat.com>
Date: Wed, 29 Jul 2009 18:55:53 +0200
Subject: [PATCH 0599/1153] drm/radeon/kms: Fix caching mode selection for GTT
 object

GTT object can either be cached,uncached or wc just let core ttm
pick the best mode according to how the bo driver and GTT memory
type was initialized.

Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_object.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c
index dd9ac2fed6d..e98cae3bf4a 100644
--- a/drivers/gpu/drm/radeon/radeon_object.c
+++ b/drivers/gpu/drm/radeon/radeon_object.c
@@ -106,7 +106,7 @@ static inline uint32_t radeon_object_flags_from_domain(uint32_t domain)
 		flags |= TTM_PL_FLAG_VRAM | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED;
 	}
 	if (domain & RADEON_GEM_DOMAIN_GTT) {
-		flags |= TTM_PL_FLAG_TT | TTM_PL_FLAG_WC | TTM_PL_FLAG_UNCACHED;
+		flags |= TTM_PL_FLAG_TT | TTM_PL_MASK_CACHING;
 	}
 	if (domain & RADEON_GEM_DOMAIN_CPU) {
 		flags |= TTM_PL_FLAG_SYSTEM | TTM_PL_MASK_CACHING;
-- 
GitLab


From 194934785a846e0a7b1b674b7b475a9d0125d2f8 Mon Sep 17 00:00:00 2001
From: TJ <linux@tjworld.net>
Date: Mon, 3 Aug 2009 13:39:09 -0700
Subject: [PATCH 0600/1153] Input: wistron_btns - support Prestigio Wifi RF
 kill button

The Prestigio 157, an old no-name clone laptop uses input keys very
similar to the Wistron 1557/MS2141 with the addition of BIOS-controlled
wireless radio frequency kill switch.

This patch adds support for the RF kill switch control and adds manual
identification of the model.

The Prestigio does not expose any recognisable identity via dmidecode
and so requires manual selection at module init using

force=1 keymap=prestigio

Signed-off-by: TJ <ubuntu@tjworld.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
---
 drivers/input/misc/wistron_btns.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/input/misc/wistron_btns.c b/drivers/input/misc/wistron_btns.c
index 26e17a9a22e..27ee976eb54 100644
--- a/drivers/input/misc/wistron_btns.c
+++ b/drivers/input/misc/wistron_btns.c
@@ -611,6 +611,20 @@ static struct key_entry keymap_wistron_generic[] __initdata = {
 	{ KE_END, 0 }
 };
 
+static struct key_entry keymap_prestigio[] __initdata = {
+	{ KE_KEY,  0x11, {KEY_PROG1} },
+	{ KE_KEY,  0x12, {KEY_PROG2} },
+	{ KE_WIFI,  0x30 },
+	{ KE_KEY,  0x22, {KEY_REWIND} },
+	{ KE_KEY,  0x23, {KEY_FORWARD} },
+	{ KE_KEY,  0x24, {KEY_PLAYPAUSE} },
+	{ KE_KEY,  0x25, {KEY_STOPCD} },
+	{ KE_KEY,  0x31, {KEY_MAIL} },
+	{ KE_KEY,  0x36, {KEY_WWW} },
+	{ KE_END,  0 }
+};
+
+
 /*
  * If your machine is not here (which is currently rather likely), please send
  * a list of buttons and their key codes (reported when loading this module
@@ -971,6 +985,8 @@ static int __init select_keymap(void)
 	if (keymap_name != NULL) {
 		if (strcmp (keymap_name, "1557/MS2141") == 0)
 			keymap = keymap_wistron_ms2141;
+		else if (strcmp (keymap_name, "prestigio") == 0)
+			keymap = keymap_prestigio;
 		else if (strcmp (keymap_name, "generic") == 0)
 			keymap = keymap_wistron_generic;
 		else {
-- 
GitLab


From d82f1c35348cebe2fb2d4a4d31ce0ab0769e3d93 Mon Sep 17 00:00:00 2001
From: Eric Miao <eric.y.miao@gmail.com>
Date: Wed, 5 Aug 2009 01:24:41 -0700
Subject: [PATCH 0601/1153] Input: matrix_keypad - make matrix keymap size
 dynamic

Remove assumption on the shift and size of rows/columns form
matrix_keypad driver.

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
---
 drivers/input/keyboard/matrix_keypad.c | 18 +++++++++---------
 include/linux/input/matrix_keypad.h    | 13 +++++++------
 2 files changed, 16 insertions(+), 15 deletions(-)

diff --git a/drivers/input/keyboard/matrix_keypad.c b/drivers/input/keyboard/matrix_keypad.c
index e9b2e7cb05b..541b981ff07 100644
--- a/drivers/input/keyboard/matrix_keypad.c
+++ b/drivers/input/keyboard/matrix_keypad.c
@@ -27,6 +27,7 @@ struct matrix_keypad {
 	const struct matrix_keypad_platform_data *pdata;
 	struct input_dev *input_dev;
 	unsigned short *keycodes;
+	unsigned int row_shift;
 
 	uint32_t last_key_state[MATRIX_MAX_COLS];
 	struct delayed_work work;
@@ -136,7 +137,7 @@ static void matrix_keypad_scan(struct work_struct *work)
 			if ((bits_changed & (1 << row)) == 0)
 				continue;
 
-			code = (row << 4) + col;
+			code = MATRIX_SCAN_CODE(row, col, keypad->row_shift);
 			input_event(input_dev, EV_MSC, MSC_SCAN, code);
 			input_report_key(input_dev,
 					 keypad->keycodes[code],
@@ -317,6 +318,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev)
 	struct matrix_keypad *keypad;
 	struct input_dev *input_dev;
 	unsigned short *keycodes;
+	unsigned int row_shift;
 	int i;
 	int err;
 
@@ -332,14 +334,11 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	if (!keymap_data->max_keymap_size) {
-		dev_err(&pdev->dev, "invalid keymap data supplied\n");
-		return -EINVAL;
-	}
+	row_shift = get_count_order(pdata->num_col_gpios);
 
 	keypad = kzalloc(sizeof(struct matrix_keypad), GFP_KERNEL);
-	keycodes = kzalloc(keymap_data->max_keymap_size *
-				sizeof(keypad->keycodes),
+	keycodes = kzalloc((pdata->num_row_gpios << row_shift) *
+				sizeof(*keycodes),
 			   GFP_KERNEL);
 	input_dev = input_allocate_device();
 	if (!keypad || !keycodes || !input_dev) {
@@ -350,6 +349,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev)
 	keypad->input_dev = input_dev;
 	keypad->pdata = pdata;
 	keypad->keycodes = keycodes;
+	keypad->row_shift = row_shift;
 	keypad->stopped = true;
 	INIT_DELAYED_WORK(&keypad->work, matrix_keypad_scan);
 	spin_lock_init(&keypad->lock);
@@ -363,7 +363,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev)
 
 	input_dev->keycode	= keycodes;
 	input_dev->keycodesize	= sizeof(*keycodes);
-	input_dev->keycodemax	= keymap_data->max_keymap_size;
+	input_dev->keycodemax	= pdata->num_row_gpios << keypad->row_shift;
 
 	for (i = 0; i < keymap_data->keymap_size; i++) {
 		unsigned int key = keymap_data->keymap[i];
@@ -371,7 +371,7 @@ static int __devinit matrix_keypad_probe(struct platform_device *pdev)
 		unsigned int col = KEY_COL(key);
 		unsigned short code = KEY_VAL(key);
 
-		keycodes[(row << 4) + col] = code;
+		keycodes[MATRIX_SCAN_CODE(row, col, row_shift)] = code;
 		__set_bit(code, input_dev->keybit);
 	}
 	__clear_bit(KEY_RESERVED, input_dev->keybit);
diff --git a/include/linux/input/matrix_keypad.h b/include/linux/input/matrix_keypad.h
index 7964516c695..15d5903af2d 100644
--- a/include/linux/input/matrix_keypad.h
+++ b/include/linux/input/matrix_keypad.h
@@ -15,12 +15,13 @@
 #define KEY_COL(k)		(((k) >> 16) & 0xff)
 #define KEY_VAL(k)		((k) & 0xffff)
 
+#define MATRIX_SCAN_CODE(row, col, row_shift)	(((row) << (row_shift)) + (col))
+
 /**
  * struct matrix_keymap_data - keymap for matrix keyboards
  * @keymap: pointer to array of uint32 values encoded with KEY() macro
  *	representing keymap
  * @keymap_size: number of entries (initialized) in this keymap
- * @max_keymap_size: maximum size of keymap supported by the device
  *
  * This structure is supposed to be used by platform code to supply
  * keymaps to drivers that implement matrix-like keypads/keyboards.
@@ -28,14 +29,13 @@
 struct matrix_keymap_data {
 	const uint32_t *keymap;
 	unsigned int	keymap_size;
-	unsigned int	max_keymap_size;
 };
 
 /**
  * struct matrix_keypad_platform_data - platform-dependent keypad data
  * @keymap_data: pointer to &matrix_keymap_data
- * @row_gpios: array of gpio numbers reporesenting rows
- * @col_gpios: array of gpio numbers reporesenting colums
+ * @row_gpios: pointer to array of gpio numbers representing rows
+ * @col_gpios: pointer to array of gpio numbers reporesenting colums
  * @num_row_gpios: actual number of row gpios used by device
  * @num_col_gpios: actual number of col gpios used by device
  * @col_scan_delay_us: delay, measured in microseconds, that is
@@ -48,8 +48,9 @@ struct matrix_keymap_data {
 struct matrix_keypad_platform_data {
 	const struct matrix_keymap_data *keymap_data;
 
-	unsigned int	row_gpios[MATRIX_MAX_ROWS];
-	unsigned int	col_gpios[MATRIX_MAX_COLS];
+	const unsigned int *row_gpios;
+	const unsigned int *col_gpios;
+
 	unsigned int	num_row_gpios;
 	unsigned int	num_col_gpios;
 
-- 
GitLab


From 45a41d147a3a31bb218201b0dd70cfe4e9ed5105 Mon Sep 17 00:00:00 2001
From: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Date: Sun, 2 Aug 2009 14:12:01 +0400
Subject: [PATCH 0602/1153] af_ieee802154: fix ioctl processing

fix two errors in ioctl processing:
1) if the ioctl isn't supported one should return -ENOIOCTLCMD
2) don't call ndo_do_ioctl if the device doesn't provide it

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
---
 net/ieee802154/af_ieee802154.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/net/ieee802154/af_ieee802154.c b/net/ieee802154/af_ieee802154.c
index 3bb6bdb1dac..af661805b9f 100644
--- a/net/ieee802154/af_ieee802154.c
+++ b/net/ieee802154/af_ieee802154.c
@@ -136,7 +136,7 @@ static int ieee802154_dev_ioctl(struct sock *sk, struct ifreq __user *arg,
 		unsigned int cmd)
 {
 	struct ifreq ifr;
-	int ret = -EINVAL;
+	int ret = -ENOIOCTLCMD;
 	struct net_device *dev;
 
 	if (copy_from_user(&ifr, arg, sizeof(struct ifreq)))
@@ -146,8 +146,10 @@ static int ieee802154_dev_ioctl(struct sock *sk, struct ifreq __user *arg,
 
 	dev_load(sock_net(sk), ifr.ifr_name);
 	dev = dev_get_by_name(sock_net(sk), ifr.ifr_name);
-	if (dev->type == ARPHRD_IEEE802154 ||
-	    dev->type == ARPHRD_IEEE802154_PHY)
+
+	if ((dev->type == ARPHRD_IEEE802154 ||
+	     dev->type == ARPHRD_IEEE802154_PHY) &&
+	    dev->netdev_ops->ndo_do_ioctl)
 		ret = dev->netdev_ops->ndo_do_ioctl(dev, &ifr, cmd);
 
 	if (!ret && copy_to_user(arg, &ifr, sizeof(struct ifreq)))
-- 
GitLab


From a9dfac3353b03432e3d46a0dde6795588c46256d Mon Sep 17 00:00:00 2001
From: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Date: Mon, 3 Aug 2009 17:53:00 +0400
Subject: [PATCH 0603/1153] af_ieee802154: provide dummy get/setsockopt

Provide dummt get/setsockopt implementations to stop these
syscalls from oopsing on our sockets.

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
---
 net/ieee802154/dgram.c | 14 ++++++++++++++
 net/ieee802154/raw.c   | 14 ++++++++++++++
 2 files changed, 28 insertions(+)

diff --git a/net/ieee802154/dgram.c b/net/ieee802154/dgram.c
index 14d39840dd6..ba8b214dda8 100644
--- a/net/ieee802154/dgram.c
+++ b/net/ieee802154/dgram.c
@@ -377,6 +377,18 @@ int ieee802154_dgram_deliver(struct net_device *dev, struct sk_buff *skb)
 	return ret;
 }
 
+static int dgram_getsockopt(struct sock *sk, int level, int optname,
+		    char __user *optval, int __user *optlen)
+{
+	return -EOPNOTSUPP;
+}
+
+static int dgram_setsockopt(struct sock *sk, int level, int optname,
+		    char __user *optval, int __user optlen)
+{
+	return -EOPNOTSUPP;
+}
+
 struct proto ieee802154_dgram_prot = {
 	.name		= "IEEE-802.15.4-MAC",
 	.owner		= THIS_MODULE,
@@ -391,5 +403,7 @@ struct proto ieee802154_dgram_prot = {
 	.connect	= dgram_connect,
 	.disconnect	= dgram_disconnect,
 	.ioctl		= dgram_ioctl,
+	.getsockopt	= dgram_getsockopt,
+	.setsockopt	= dgram_setsockopt,
 };
 
diff --git a/net/ieee802154/raw.c b/net/ieee802154/raw.c
index fca44d59f97..9315977c4c6 100644
--- a/net/ieee802154/raw.c
+++ b/net/ieee802154/raw.c
@@ -238,6 +238,18 @@ void ieee802154_raw_deliver(struct net_device *dev, struct sk_buff *skb)
 	read_unlock(&raw_lock);
 }
 
+static int raw_getsockopt(struct sock *sk, int level, int optname,
+		    char __user *optval, int __user *optlen)
+{
+	return -EOPNOTSUPP;
+}
+
+static int raw_setsockopt(struct sock *sk, int level, int optname,
+		    char __user *optval, int __user optlen)
+{
+	return -EOPNOTSUPP;
+}
+
 struct proto ieee802154_raw_prot = {
 	.name		= "IEEE-802.15.4-RAW",
 	.owner		= THIS_MODULE,
@@ -250,5 +262,7 @@ struct proto ieee802154_raw_prot = {
 	.unhash		= raw_unhash,
 	.connect	= raw_connect,
 	.disconnect	= raw_disconnect,
+	.getsockopt	= raw_getsockopt,
+	.setsockopt	= raw_setsockopt,
 };
 
-- 
GitLab


From 53a27b39ff4d2492f84b1fdc2f0047175f0b0b93 Mon Sep 17 00:00:00 2001
From: Marcelo Tosatti <mtosatti@redhat.com>
Date: Wed, 5 Aug 2009 15:43:58 -0300
Subject: [PATCH 0604/1153] KVM: MMU: limit rmap chain length

Otherwise the host can spend too long traversing an rmap chain, which
happens under a spinlock.

Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 arch/x86/kvm/mmu.c | 33 ++++++++++++++++++++++++++++-----
 1 file changed, 28 insertions(+), 5 deletions(-)

diff --git a/arch/x86/kvm/mmu.c b/arch/x86/kvm/mmu.c
index 49a10d00830..0ef5bb2b404 100644
--- a/arch/x86/kvm/mmu.c
+++ b/arch/x86/kvm/mmu.c
@@ -489,16 +489,20 @@ static unsigned long *gfn_to_rmap(struct kvm *kvm, gfn_t gfn, int lpage)
  *
  * If rmapp bit zero is one, (then rmap & ~1) points to a struct kvm_rmap_desc
  * containing more mappings.
+ *
+ * Returns the number of rmap entries before the spte was added or zero if
+ * the spte was not added.
+ *
  */
-static void rmap_add(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn, int lpage)
+static int rmap_add(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn, int lpage)
 {
 	struct kvm_mmu_page *sp;
 	struct kvm_rmap_desc *desc;
 	unsigned long *rmapp;
-	int i;
+	int i, count = 0;
 
 	if (!is_rmap_pte(*spte))
-		return;
+		return count;
 	gfn = unalias_gfn(vcpu->kvm, gfn);
 	sp = page_header(__pa(spte));
 	sp->gfns[spte - sp->spt] = gfn;
@@ -515,8 +519,10 @@ static void rmap_add(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn, int lpage)
 	} else {
 		rmap_printk("rmap_add: %p %llx many->many\n", spte, *spte);
 		desc = (struct kvm_rmap_desc *)(*rmapp & ~1ul);
-		while (desc->shadow_ptes[RMAP_EXT-1] && desc->more)
+		while (desc->shadow_ptes[RMAP_EXT-1] && desc->more) {
 			desc = desc->more;
+			count += RMAP_EXT;
+		}
 		if (desc->shadow_ptes[RMAP_EXT-1]) {
 			desc->more = mmu_alloc_rmap_desc(vcpu);
 			desc = desc->more;
@@ -525,6 +531,7 @@ static void rmap_add(struct kvm_vcpu *vcpu, u64 *spte, gfn_t gfn, int lpage)
 			;
 		desc->shadow_ptes[i] = spte;
 	}
+	return count;
 }
 
 static void rmap_desc_remove_entry(unsigned long *rmapp,
@@ -754,6 +761,19 @@ static int kvm_age_rmapp(struct kvm *kvm, unsigned long *rmapp)
 	return young;
 }
 
+#define RMAP_RECYCLE_THRESHOLD 1000
+
+static void rmap_recycle(struct kvm_vcpu *vcpu, gfn_t gfn, int lpage)
+{
+	unsigned long *rmapp;
+
+	gfn = unalias_gfn(vcpu->kvm, gfn);
+	rmapp = gfn_to_rmap(vcpu->kvm, gfn, lpage);
+
+	kvm_unmap_rmapp(vcpu->kvm, rmapp);
+	kvm_flush_remote_tlbs(vcpu->kvm);
+}
+
 int kvm_age_hva(struct kvm *kvm, unsigned long hva)
 {
 	return kvm_handle_hva(kvm, hva, kvm_age_rmapp);
@@ -1741,6 +1761,7 @@ static void mmu_set_spte(struct kvm_vcpu *vcpu, u64 *shadow_pte,
 {
 	int was_rmapped = 0;
 	int was_writeble = is_writeble_pte(*shadow_pte);
+	int rmap_count;
 
 	pgprintk("%s: spte %llx access %x write_fault %d"
 		 " user_fault %d gfn %lx\n",
@@ -1782,9 +1803,11 @@ static void mmu_set_spte(struct kvm_vcpu *vcpu, u64 *shadow_pte,
 
 	page_header_update_slot(vcpu->kvm, shadow_pte, gfn);
 	if (!was_rmapped) {
-		rmap_add(vcpu, shadow_pte, gfn, largepage);
+		rmap_count = rmap_add(vcpu, shadow_pte, gfn, largepage);
 		if (!is_rmap_pte(*shadow_pte))
 			kvm_release_pfn_clean(pfn);
+		if (rmap_count > RMAP_RECYCLE_THRESHOLD)
+			rmap_recycle(vcpu, gfn, largepage);
 	} else {
 		if (was_writeble)
 			kvm_release_pfn_dirty(pfn);
-- 
GitLab


From c5b1525533c484238015c48c78f86d49a1bfb86b Mon Sep 17 00:00:00 2001
From: Sheng Yang <sheng@linux.intel.com>
Date: Thu, 6 Aug 2009 13:31:56 +0800
Subject: [PATCH 0605/1153] intel-iommu: Fix enabling snooping feature by
 mistake

Two defects work together result in KVM device passthrough randomly can't
work:
1. iommu_snooping is not initialized to zero when vm_iommu_init() called.
So it is possible to get a random value.
2. One line added by commit 2c2e2c38("IOMMU Identity Mapping Support")
change the code path, let it bypass domain_update_iommu_cap(), as well as
missing the increment of domain iommu reference count.

The latter is also likely to cause a leak of domains on repeated VMM
assignment and deassignment.

Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
 drivers/pci/intel-iommu.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/pci/intel-iommu.c b/drivers/pci/intel-iommu.c
index af7ff9b5aed..2314ad7ee5f 100644
--- a/drivers/pci/intel-iommu.c
+++ b/drivers/pci/intel-iommu.c
@@ -1505,7 +1505,6 @@ static int domain_context_mapping_one(struct dmar_domain *domain, int segment,
 			}
 
 			set_bit(num, iommu->domain_ids);
-			set_bit(iommu->seq_id, &domain->iommu_bmp);
 			iommu->domains[num] = domain;
 			id = num;
 		}
@@ -3409,6 +3408,7 @@ static int md_domain_init(struct dmar_domain *domain, int guest_width)
 
 	domain->iommu_count = 0;
 	domain->iommu_coherency = 0;
+	domain->iommu_snooping = 0;
 	domain->max_addr = 0;
 
 	/* always allocate the top pgd */
-- 
GitLab


From e0d82a0a4e9841b787e6431ccfbb515546c55dc2 Mon Sep 17 00:00:00 2001
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Thu, 6 Aug 2009 21:16:44 +1000
Subject: [PATCH 0606/1153] perf_counter/powerpc: Check oprofile_cpu_type for
 NULL before using it

If the current CPU doesn't support performance counters,
cur_cpu_spec->oprofile_cpu_type can be NULL. The current
perf_counter modules don't test for that case and would thus
crash at boot time.

Bug reported by David Woodhouse.

Reported-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
LKML-Reference: <19066.48028.446975.501454@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/powerpc/kernel/mpc7450-pmu.c | 3 ++-
 arch/powerpc/kernel/power4-pmu.c  | 3 ++-
 arch/powerpc/kernel/power5+-pmu.c | 5 +++--
 arch/powerpc/kernel/power5-pmu.c  | 3 ++-
 arch/powerpc/kernel/power6-pmu.c  | 3 ++-
 arch/powerpc/kernel/power7-pmu.c  | 3 ++-
 arch/powerpc/kernel/ppc970-pmu.c  | 5 +++--
 7 files changed, 16 insertions(+), 9 deletions(-)

diff --git a/arch/powerpc/kernel/mpc7450-pmu.c b/arch/powerpc/kernel/mpc7450-pmu.c
index c244133c67a..cc466d039af 100644
--- a/arch/powerpc/kernel/mpc7450-pmu.c
+++ b/arch/powerpc/kernel/mpc7450-pmu.c
@@ -407,7 +407,8 @@ struct power_pmu mpc7450_pmu = {
 
 static int init_mpc7450_pmu(void)
 {
-	if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc/7450"))
+	if (!cur_cpu_spec->oprofile_cpu_type ||
+	    strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc/7450"))
 		return -ENODEV;
 
 	return register_power_pmu(&mpc7450_pmu);
diff --git a/arch/powerpc/kernel/power4-pmu.c b/arch/powerpc/kernel/power4-pmu.c
index db90b0c5c27..3c90a3d9173 100644
--- a/arch/powerpc/kernel/power4-pmu.c
+++ b/arch/powerpc/kernel/power4-pmu.c
@@ -606,7 +606,8 @@ static struct power_pmu power4_pmu = {
 
 static int init_power4_pmu(void)
 {
-	if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power4"))
+	if (!cur_cpu_spec->oprofile_cpu_type ||
+	    strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power4"))
 		return -ENODEV;
 
 	return register_power_pmu(&power4_pmu);
diff --git a/arch/powerpc/kernel/power5+-pmu.c b/arch/powerpc/kernel/power5+-pmu.c
index f4adca8e98a..31918af3e35 100644
--- a/arch/powerpc/kernel/power5+-pmu.c
+++ b/arch/powerpc/kernel/power5+-pmu.c
@@ -678,8 +678,9 @@ static struct power_pmu power5p_pmu = {
 
 static int init_power5p_pmu(void)
 {
-	if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5+")
-	    && strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5++"))
+	if (!cur_cpu_spec->oprofile_cpu_type ||
+	    (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5+")
+	     && strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5++")))
 		return -ENODEV;
 
 	return register_power_pmu(&power5p_pmu);
diff --git a/arch/powerpc/kernel/power5-pmu.c b/arch/powerpc/kernel/power5-pmu.c
index 29b2c6c0e83..867f6f66396 100644
--- a/arch/powerpc/kernel/power5-pmu.c
+++ b/arch/powerpc/kernel/power5-pmu.c
@@ -618,7 +618,8 @@ static struct power_pmu power5_pmu = {
 
 static int init_power5_pmu(void)
 {
-	if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5"))
+	if (!cur_cpu_spec->oprofile_cpu_type ||
+	    strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power5"))
 		return -ENODEV;
 
 	return register_power_pmu(&power5_pmu);
diff --git a/arch/powerpc/kernel/power6-pmu.c b/arch/powerpc/kernel/power6-pmu.c
index 09ae5bf5bda..fa21890531d 100644
--- a/arch/powerpc/kernel/power6-pmu.c
+++ b/arch/powerpc/kernel/power6-pmu.c
@@ -537,7 +537,8 @@ static struct power_pmu power6_pmu = {
 
 static int init_power6_pmu(void)
 {
-	if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power6"))
+	if (!cur_cpu_spec->oprofile_cpu_type ||
+	    strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power6"))
 		return -ENODEV;
 
 	return register_power_pmu(&power6_pmu);
diff --git a/arch/powerpc/kernel/power7-pmu.c b/arch/powerpc/kernel/power7-pmu.c
index 5a9f5cbd40a..388cf57ad82 100644
--- a/arch/powerpc/kernel/power7-pmu.c
+++ b/arch/powerpc/kernel/power7-pmu.c
@@ -366,7 +366,8 @@ static struct power_pmu power7_pmu = {
 
 static int init_power7_pmu(void)
 {
-	if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power7"))
+	if (!cur_cpu_spec->oprofile_cpu_type ||
+	    strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/power7"))
 		return -ENODEV;
 
 	return register_power_pmu(&power7_pmu);
diff --git a/arch/powerpc/kernel/ppc970-pmu.c b/arch/powerpc/kernel/ppc970-pmu.c
index 833097ac45d..75dccb71a04 100644
--- a/arch/powerpc/kernel/ppc970-pmu.c
+++ b/arch/powerpc/kernel/ppc970-pmu.c
@@ -488,8 +488,9 @@ static struct power_pmu ppc970_pmu = {
 
 static int init_ppc970_pmu(void)
 {
-	if (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/970")
-	    && strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/970MP"))
+	if (!cur_cpu_spec->oprofile_cpu_type ||
+	    (strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/970")
+	     && strcmp(cur_cpu_spec->oprofile_cpu_type, "ppc64/970MP")))
 		return -ENODEV;
 
 	return register_power_pmu(&ppc970_pmu);
-- 
GitLab


From 469535a598f28c13a2a42037e1b778f671af1d16 Mon Sep 17 00:00:00 2001
From: Robert Richter <robert.richter@amd.com>
Date: Thu, 30 Jul 2009 19:19:18 +0200
Subject: [PATCH 0607/1153] ring-buffer: Fix advance of reader in
 rb_buffer_peek()

When calling rb_buffer_peek() from ring_buffer_consume() and a
padding event is returned, the function rb_advance_reader() is
called twice. This may lead to missing samples or under high
workloads to the warning below. This patch fixes this. If a padding
event is returned by rb_buffer_peek() it will be consumed by the
calling function now.

Also, I simplified some code in ring_buffer_consume().

------------[ cut here ]------------
WARNING: at /dev/shm/.source/linux/kernel/trace/ring_buffer.c:2289 rb_advance_reader+0x2e/0xc5()
Hardware name: Anaheim
Modules linked in:
Pid: 29, comm: events/2 Tainted: G        W  2.6.31-rc3-oprofile-x86_64-standard-00059-g5050dc2 #1
Call Trace:
[<ffffffff8106776f>] ? rb_advance_reader+0x2e/0xc5
[<ffffffff81039ffe>] warn_slowpath_common+0x77/0x8f
[<ffffffff8103a025>] warn_slowpath_null+0xf/0x11
[<ffffffff8106776f>] rb_advance_reader+0x2e/0xc5
[<ffffffff81068bda>] ring_buffer_consume+0xa0/0xd2
[<ffffffff81326933>] op_cpu_buffer_read_entry+0x21/0x9e
[<ffffffff810be3af>] ? __find_get_block+0x4b/0x165
[<ffffffff8132749b>] sync_buffer+0xa5/0x401
[<ffffffff810be3af>] ? __find_get_block+0x4b/0x165
[<ffffffff81326c1b>] ? wq_sync_buffer+0x0/0x78
[<ffffffff81326c76>] wq_sync_buffer+0x5b/0x78
[<ffffffff8104aa30>] worker_thread+0x113/0x1ac
[<ffffffff8104dd95>] ? autoremove_wake_function+0x0/0x38
[<ffffffff8104a91d>] ? worker_thread+0x0/0x1ac
[<ffffffff8104dc9a>] kthread+0x88/0x92
[<ffffffff8100bdba>] child_rip+0xa/0x20
[<ffffffff8104dc12>] ? kthread+0x0/0x92
[<ffffffff8100bdb0>] ? child_rip+0x0/0x20
---[ end trace f561c0a58fcc89bd ]---

Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: <stable@kernel.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/trace/ring_buffer.c | 10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)

diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c
index 2606cee433d..d4d3580a894 100644
--- a/kernel/trace/ring_buffer.c
+++ b/kernel/trace/ring_buffer.c
@@ -2383,7 +2383,6 @@ rb_buffer_peek(struct ring_buffer *buffer, int cpu, u64 *ts)
 		 * the box. Return the padding, and we will release
 		 * the current locks, and try again.
 		 */
-		rb_advance_reader(cpu_buffer);
 		return event;
 
 	case RINGBUF_TYPE_TIME_EXTEND:
@@ -2519,6 +2518,8 @@ ring_buffer_peek(struct ring_buffer *buffer, int cpu, u64 *ts)
 	if (dolock)
 		spin_lock(&cpu_buffer->reader_lock);
 	event = rb_buffer_peek(buffer, cpu, ts);
+	if (event && event->type_len == RINGBUF_TYPE_PADDING)
+		rb_advance_reader(cpu_buffer);
 	if (dolock)
 		spin_unlock(&cpu_buffer->reader_lock);
 	local_irq_restore(flags);
@@ -2590,12 +2591,9 @@ ring_buffer_consume(struct ring_buffer *buffer, int cpu, u64 *ts)
 		spin_lock(&cpu_buffer->reader_lock);
 
 	event = rb_buffer_peek(buffer, cpu, ts);
-	if (!event)
-		goto out_unlock;
-
-	rb_advance_reader(cpu_buffer);
+	if (event)
+		rb_advance_reader(cpu_buffer);
 
- out_unlock:
 	if (dolock)
 		spin_unlock(&cpu_buffer->reader_lock);
 	local_irq_restore(flags);
-- 
GitLab


From 4d1e00a8af426500edfb8643fa6c375b89f1f804 Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Wed, 5 Aug 2009 19:02:49 -0300
Subject: [PATCH 0608/1153] perf symbol: Fix symbol parsing in certain cases:
 use the build-id as a symlink

In some cases distros have binaries and debuginfo in weird places:

[root@doppio tuna]# ls -la /usr/lib64/{xulrunner-1.9.1/xulrunner-stub,firefox-3.5.2/firefox}
-rwxr-xr-x 1 root root 90024 2009-08-03 19:45 /usr/lib64/firefox-3.5.2/firefox
-rwxr-xr-x 1 root root 90024 2009-08-03 18:23 /usr/lib64/xulrunner-1.9.1/xulrunner-stub
[root@doppio tuna]# sha1sum /usr/lib64/{xulrunner-1.9.1/xulrunner-stub,firefox-3.5.2/firefox}
19a858077d263d5de22c9c5da250d3e4396ae739  /usr/lib64/xulrunner-1.9.1/xulrunner-stub
19a858077d263d5de22c9c5da250d3e4396ae739  /usr/lib64/firefox-3.5.2/firefox
[root@doppio tuna]# rpm -qf /usr/lib64/{xulrunner-1.9.1/xulrunner-stub,firefox-3.5.2/firefox}
xulrunner-1.9.1.2-1.fc11.x86_64
firefox-3.5.2-2.fc11.x86_64
[root@doppio tuna]# ls -la /usr/lib/debug/{usr/lib64/xulrunner-1.9.1/xulrunner-stub,usr/lib64/firefox-3.5.2/firefox}.debug
ls: cannot access /usr/lib/debug/usr/lib64/firefox-3.5.2/firefox.debug: No such file or directory
-rwxr-xr-x 1 root root 403608 2009-08-03 18:22 /usr/lib/debug/usr/lib64/xulrunner-1.9.1/xulrunner-stub.debug

Seemingly we don't have a .symtab when we actually can find it
if we use the .note.gnu.build-id ELF section put in place by
some distros. Use it and find the symbols we need.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/util/symbol.c | 76 ++++++++++++++++++++++++++++++++++++++--
 1 file changed, 73 insertions(+), 3 deletions(-)

diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c
index 0580b94785e..16ddca20294 100644
--- a/tools/perf/util/symbol.c
+++ b/tools/perf/util/symbol.c
@@ -661,10 +661,69 @@ out_close:
 	return err;
 }
 
+#define BUILD_ID_SIZE 128
+
+static char *dso__read_build_id(struct dso *self, int verbose)
+{
+	int i;
+	GElf_Ehdr ehdr;
+	GElf_Shdr shdr;
+	Elf_Data *build_id_data;
+	Elf_Scn *sec;
+	char *build_id = NULL, *bid;
+	unsigned char *raw;
+	Elf *elf;
+	int fd = open(self->name, O_RDONLY);
+
+	if (fd < 0)
+		goto out;
+
+	elf = elf_begin(fd, ELF_C_READ_MMAP, NULL);
+	if (elf == NULL) {
+		if (verbose)
+			fprintf(stderr, "%s: cannot read %s ELF file.\n",
+				__func__, self->name);
+		goto out_close;
+	}
+
+	if (gelf_getehdr(elf, &ehdr) == NULL) {
+		if (verbose)
+			fprintf(stderr, "%s: cannot get elf header.\n", __func__);
+		goto out_elf_end;
+	}
+
+	sec = elf_section_by_name(elf, &ehdr, &shdr, ".note.gnu.build-id", NULL);
+	if (sec == NULL)
+		goto out_elf_end;
+
+	build_id_data = elf_getdata(sec, NULL);
+	if (build_id_data == NULL)
+		goto out_elf_end;
+	build_id = malloc(BUILD_ID_SIZE);
+	if (build_id == NULL)
+		goto out_elf_end;
+	raw = build_id_data->d_buf + 16;
+	bid = build_id;
+
+	for (i = 0; i < 20; ++i) {
+		sprintf(bid, "%02x", *raw);
+		++raw;
+		bid += 2;
+	}
+	if (verbose)
+		printf("%s(%s): %s\n", __func__, self->name, build_id);
+out_elf_end:
+	elf_end(elf);
+out_close:
+	close(fd);
+out:
+	return build_id;
+}
+
 int dso__load(struct dso *self, symbol_filter_t filter, int verbose)
 {
-	int size = strlen(self->name) + sizeof("/usr/lib/debug%s.debug");
-	char *name = malloc(size);
+	int size = PATH_MAX;
+	char *name = malloc(size), *build_id = NULL;
 	int variant = 0;
 	int ret = -1;
 	int fd;
@@ -686,7 +745,18 @@ more:
 		case 1: /* Ubuntu */
 			snprintf(name, size, "/usr/lib/debug%s", self->name);
 			break;
-		case 2: /* Sane people */
+		case 2:
+			build_id = dso__read_build_id(self, verbose);
+			if (build_id != NULL) {
+				snprintf(name, size,
+					 "/usr/lib/debug/.build-id/%.2s/%s.debug",
+					build_id, build_id + 2);
+				free(build_id);
+				break;
+			}
+			variant++;
+			/* Fall thru */
+		case 3: /* Sane people */
 			snprintf(name, size, "%s", self->name);
 			break;
 
-- 
GitLab


From 9424edc2da097c8589fcc24a72552d33e54be161 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Wed, 5 Aug 2009 14:05:16 +0200
Subject: [PATCH 0609/1153] perf: Auto-detect libelf

Adds autodetection for libelf as well, and simplifies the
libbfd code. Furthermore, fail make with an error when libelf
is not found and warn about the lack of libbfd.

Also provide an option to build a 32bit version even though you
might be running a 64bit kernel.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Makefile | 15 +++++++++++----
 1 file changed, 11 insertions(+), 4 deletions(-)

diff --git a/tools/perf/Makefile b/tools/perf/Makefile
index ff905aceb4f..1916e44b9bb 100644
--- a/tools/perf/Makefile
+++ b/tools/perf/Makefile
@@ -158,8 +158,10 @@ uname_P := $(shell sh -c 'uname -p 2>/dev/null || echo not')
 uname_V := $(shell sh -c 'uname -v 2>/dev/null || echo not')
 
 # If we're on a 64-bit kernel, use -m64
-ifneq ($(patsubst %64,%,$(uname_M)),$(uname_M))
-  M64 := -m64
+ifndef NO_64BIT
+	ifneq ($(patsubst %64,%,$(uname_M)),$(uname_M))
+	  M64 := -m64
+	endif
 endif
 
 # CFLAGS and LDFLAGS are for the users to override from the command line.
@@ -373,19 +375,24 @@ ifeq ($(uname_S),Darwin)
 	PTHREAD_LIBS =
 endif
 
+ifneq ($(shell sh -c "(echo '\#include <libelf.h>'; echo 'int main(void) { Elf * elf = elf_begin(0, ELF_C_READ_MMAP, 0); return (long)elf; }') | $(CC) -x c - $(ALL_CFLAGS) -D_LARGEFILE64_SOURCE -D_FILE_OFFSET_BITS=64 -o /dev/null $(ALL_LDFLAGS) > /dev/null 2>&1 && echo y"), y)
+	msg := $(error No libelf.h/libelf found, please install libelf-dev/elfutils-libelf-devel);
+endif
+
 ifdef NO_DEMANGLE
 	BASIC_CFLAGS += -DNO_DEMANGLE
 else
 
-	has_bfd := $(shell sh -c "(echo '\#include <stdio.h>'; echo '\#include <bfd.h>'; echo '\#ifndef DMGL_PARAMS'; echo '\#define DMGL_PARAMS (1 << 0)'; echo '\#define DMGL_ANSI (1 << 1)'; echo '\#endif'; echo 'int main(int argc, char **argv) { bfd_demangle(NULL, argv[0], DMGL_PARAMS | DMGL_ANSI); return 0; }') | gcc -x c - -lbfd > /dev/null 2>&1 && echo y")
+	has_bfd := $(shell sh -c "(echo '\#include <bfd.h>'; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd > /dev/null 2>&1 && echo y")
 
-	has_bfd_iberty := $(shell sh -c "(echo '\#include <stdio.h>'; echo '\#include <bfd.h>'; echo '\#ifndef DMGL_PARAMS'; echo '\#define DMGL_PARAMS (1 << 0)'; echo '\#define DMGL_ANSI (1 << 1)'; echo '\#endif'; echo 'int main(int argc, char **argv) { bfd_demangle(NULL, argv[0], DMGL_PARAMS | DMGL_ANSI); return 0; }') | gcc -x c - -lbfd -liberty > /dev/null 2>&1 && echo y")
+	has_bfd_iberty := $(shell sh -c "(echo '\#include <bfd.h>'; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty > /dev/null 2>&1 && echo y")
 
 	ifeq ($(has_bfd),y)
 		EXTLIBS += -lbfd
 	else ifeq ($(has_bfd_iberty),y)
 		EXTLIBS += -lbfd -liberty
 	else
+		msg := $(warning No bfd.h/libbfd found, install binutils-dev[el] to gain symbol demangling)
 		BASIC_CFLAGS += -DNO_DEMANGLE
 	endif
 endif
-- 
GitLab


From 1054598cab8674438675085fae459e960eb10799 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <peterz@infradead.org>
Date: Thu, 6 Aug 2009 18:06:26 +0200
Subject: [PATCH 0610/1153] perf_counter: Fix double list iteration in per task
 precise stats

Brice Goglin reported this crash with per task precise stats:

> I finally managed to test the threaded perfcounter statistics (thanks a
> lot for implementing it). I am running 2.6.31-rc5 (with the AMD
> magny-cours patches but I don't think they matter here). I am trying to
> measure local/remote memory accesses per thread during the well-known
> stream benchmark. It's compiled with OpenMP using 16 threads on a
> quad-socket quad-core barcelona machine.
>
> Command line is:
>  /mnt/scratch/bgoglin/cpunode/linux-2.6.31/tools/perf/perf record -f -s
> -e r1000001e0 -e r1000002e0 -e r1000004e0 -e r1000008e0 ./stream
>
> It seems to work fine with a single -e <counter> on the command line
> while it crashes when there are at least 2 of them.
> It seems to work fine without -s as well.

A silly copy-paste resulted in a messed up iteration which would
cause the OOPS.

Reported-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
LKML-Reference: <1249574786.32113.550.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 199ed477131..673c1aaf733 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -1104,7 +1104,7 @@ static void perf_counter_sync_stat(struct perf_counter_context *ctx,
 		__perf_counter_sync_stat(counter, next_counter);
 
 		counter = list_next_entry(counter, event_entry);
-		next_counter = list_next_entry(counter, event_entry);
+		next_counter = list_next_entry(next_counter, event_entry);
 	}
 }
 
-- 
GitLab


From 17ac2e9c58b69a1e25460a568eae1b0dc0188c25 Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Thu, 6 Aug 2009 03:34:06 +0000
Subject: [PATCH 0611/1153] rose: Fix rose_getname() leak

rose_getname() can leak kernel memory to user.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/rose/af_rose.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/rose/af_rose.c b/net/rose/af_rose.c
index f0a76f6bca7..e5f478ca3d6 100644
--- a/net/rose/af_rose.c
+++ b/net/rose/af_rose.c
@@ -954,6 +954,7 @@ static int rose_getname(struct socket *sock, struct sockaddr *uaddr,
 	struct rose_sock *rose = rose_sk(sk);
 	int n;
 
+	memset(srose, 0, sizeof(*srose));
 	if (peer != 0) {
 		if (sk->sk_state != TCP_ESTABLISHED)
 			return -ENOTCONN;
-- 
GitLab


From 80922bbb12a105f858a8f0abb879cb4302d0ecaa Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Thu, 6 Aug 2009 03:48:36 +0000
Subject: [PATCH 0612/1153] econet: Fix econet_getname() leak

econet_getname() can leak kernel memory to user.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/econet/af_econet.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/econet/af_econet.c b/net/econet/af_econet.c
index 2e1f836d424..f0bbc57926c 100644
--- a/net/econet/af_econet.c
+++ b/net/econet/af_econet.c
@@ -520,6 +520,7 @@ static int econet_getname(struct socket *sock, struct sockaddr *uaddr,
 	if (peer)
 		return -EOPNOTSUPP;
 
+	memset(sec, 0, sizeof(*sec));
 	mutex_lock(&econet_mutex);
 
 	sk = sock->sk;
-- 
GitLab


From f6b97b29513950bfbf621a83d85b6f86b39ec8db Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Thu, 6 Aug 2009 03:31:07 +0000
Subject: [PATCH 0613/1153] netrom: Fix nr_getname() leak

nr_getname() can leak kernel memory to user.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/netrom/af_netrom.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/netrom/af_netrom.c b/net/netrom/af_netrom.c
index ce51ce012cd..ce1a34b99c2 100644
--- a/net/netrom/af_netrom.c
+++ b/net/netrom/af_netrom.c
@@ -847,6 +847,7 @@ static int nr_getname(struct socket *sock, struct sockaddr *uaddr,
 		sax->fsa_ax25.sax25_family = AF_NETROM;
 		sax->fsa_ax25.sax25_ndigis = 1;
 		sax->fsa_ax25.sax25_call   = nr->user_addr;
+		memset(sax->fsa_digipeater, 0, sizeof(sax->fsa_digipeater));
 		sax->fsa_digipeater[0]     = nr->dest_addr;
 		*uaddr_len = sizeof(struct full_sockaddr_ax25);
 	} else {
-- 
GitLab


From 3d392475c873c10c10d6d96b94d092a34ebd4791 Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Thu, 6 Aug 2009 02:27:43 +0000
Subject: [PATCH 0614/1153] appletalk: fix atalk_getname() leak

atalk_getname() can leak 8 bytes of kernel memory to user

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/appletalk/ddp.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/appletalk/ddp.c b/net/appletalk/ddp.c
index 590b8396362..9ef6ff26eb0 100644
--- a/net/appletalk/ddp.c
+++ b/net/appletalk/ddp.c
@@ -1237,6 +1237,7 @@ static int atalk_getname(struct socket *sock, struct sockaddr *uaddr,
 			return -ENOBUFS;
 
 	*uaddr_len = sizeof(struct sockaddr_at);
+	memset(&sat.sat_zero, 0, sizeof(sat.sat_zero));
 
 	if (peer) {
 		if (sk->sk_state != TCP_ESTABLISHED)
-- 
GitLab


From 09384dfc76e526c3993c09c42e016372dc9dd22c Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Thu, 6 Aug 2009 03:55:04 +0000
Subject: [PATCH 0615/1153] irda: Fix irda_getname() leak

irda_getname() can leak kernel memory to user.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/irda/af_irda.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/irda/af_irda.c b/net/irda/af_irda.c
index cb762c8723e..3ec2b434ea7 100644
--- a/net/irda/af_irda.c
+++ b/net/irda/af_irda.c
@@ -714,6 +714,7 @@ static int irda_getname(struct socket *sock, struct sockaddr *uaddr,
 	struct sock *sk = sock->sk;
 	struct irda_sock *self = irda_sk(sk);
 
+	memset(&saddr, 0, sizeof(saddr));
 	if (peer) {
 		if (sk->sk_state != TCP_ESTABLISHED)
 			return -ENOTCONN;
-- 
GitLab


From 7dbdee2e9a2ac42ea5135801bcc9d1a8e3f672aa Mon Sep 17 00:00:00 2001
From: Steven Rostedt <srostedt@redhat.com>
Date: Thu, 6 Aug 2009 19:53:18 -0400
Subject: [PATCH 0616/1153] tracing: Fix recordmcount.pl to handle sections
 with only weak functions

Roland Dreier found that a section that contained only a weak
function in one of the staging drivers and this caused
recordmcount.pl to spit out a warning and fail.

Although it is strange that a driver would have a weak function, and
this function only be used in one place, it should not be something
to make recordmcount.pl fail.

This patch fixes the issue in a simple manner: if only weak
functions exist in a section, then that section will not be
recorded.

Reported-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 scripts/recordmcount.pl | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/scripts/recordmcount.pl b/scripts/recordmcount.pl
index 4889c44d71b..911ba7ffab8 100755
--- a/scripts/recordmcount.pl
+++ b/scripts/recordmcount.pl
@@ -393,7 +393,7 @@ while (<IN>) {
 	    $read_function = 0;
 	}
 	# print out any recorded offsets
-	update_funcs() if ($text_found);
+	update_funcs() if (defined($ref_func));
 
 	# reset all markers and arrays
 	$text_found = 0;
@@ -444,7 +444,7 @@ while (<IN>) {
 }
 
 # dump out anymore offsets that may have been found
-update_funcs() if ($text_found);
+update_funcs() if (defined($ref_func));
 
 # If we did not find any mcount callers, we are done (do nothing).
 if (!$opened) {
-- 
GitLab


From 677c1dd706d9cc384730cbd52baf821923d8be9b Mon Sep 17 00:00:00 2001
From: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Date: Fri, 7 Aug 2009 10:39:24 +0200
Subject: [PATCH 0617/1153] [S390] kernel: Storing machine flags early in
 lowcore

Currently, the machine_flags are stored late in the startup
initialization which results in failing machine type checks
(e.g. for MACHINE_IS_VM).
To allow these checks, store the machine flags in the lowcore
when the machine type has been detected.

Moving the machine_flags to the lowcore has been introduced with
git commit 25097bf153391f7be4c591d47061b3dc4990dac2

Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
---
 arch/s390/kernel/early.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/s390/kernel/early.c b/arch/s390/kernel/early.c
index 8d15314381e..cae14c49951 100644
--- a/arch/s390/kernel/early.c
+++ b/arch/s390/kernel/early.c
@@ -208,6 +208,9 @@ static noinline __init void detect_machine_type(void)
 		machine_flags |= MACHINE_FLAG_KVM;
 	else
 		machine_flags |= MACHINE_FLAG_VM;
+
+	/* Store machine flags for setting up lowcore early */
+	S390_lowcore.machine_flags = machine_flags;
 }
 
 static __init void early_pgm_check_handler(void)
-- 
GitLab


From 53cb780adbe69df90c8dc23e992ce40455e687c3 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Fri, 7 Aug 2009 10:39:25 +0200
Subject: [PATCH 0618/1153] [S390] KVM: Read buffer overflow

Check whether index is within bounds before testing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
---
 arch/s390/kvm/sigp.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/arch/s390/kvm/sigp.c b/arch/s390/kvm/sigp.c
index 36678835034..0ef81d6776e 100644
--- a/arch/s390/kvm/sigp.c
+++ b/arch/s390/kvm/sigp.c
@@ -169,7 +169,7 @@ static int __sigp_set_prefix(struct kvm_vcpu *vcpu, u16 cpu_addr, u32 address,
 			     unsigned long *reg)
 {
 	struct kvm_s390_float_interrupt *fi = &vcpu->kvm->arch.float_int;
-	struct kvm_s390_local_interrupt *li;
+	struct kvm_s390_local_interrupt *li = NULL;
 	struct kvm_s390_interrupt_info *inti;
 	int rc;
 	u8 tmp;
@@ -189,9 +189,10 @@ static int __sigp_set_prefix(struct kvm_vcpu *vcpu, u16 cpu_addr, u32 address,
 		return 2; /* busy */
 
 	spin_lock(&fi->lock);
-	li = fi->local_int[cpu_addr];
+	if (cpu_addr < KVM_MAX_VCPUS)
+		li = fi->local_int[cpu_addr];
 
-	if ((cpu_addr >= KVM_MAX_VCPUS) || (li == NULL)) {
+	if (li == NULL) {
 		rc = 1; /* incorrect state */
 		*reg &= SIGP_STAT_INCORRECT_STATE;
 		kfree(inti);
-- 
GitLab


From 9795447f71324d8f14c19ed68b43c883135c3f59 Mon Sep 17 00:00:00 2001
From: Li Zefan <lizf@cn.fujitsu.com>
Date: Fri, 7 Aug 2009 16:37:10 +0800
Subject: [PATCH 0619/1153] lockdep: Fix file mode of lock_stat

/proc/lock_stat is writable.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <4A7BE7B6.10904@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/lockdep_proc.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/kernel/lockdep_proc.c b/kernel/lockdep_proc.c
index d7135aa2d2c..e94caa666db 100644
--- a/kernel/lockdep_proc.c
+++ b/kernel/lockdep_proc.c
@@ -758,7 +758,8 @@ static int __init lockdep_proc_init(void)
 		    &proc_lockdep_stats_operations);
 
 #ifdef CONFIG_LOCK_STAT
-	proc_create("lock_stat", S_IRUSR, NULL, &proc_lock_stat_operations);
+	proc_create("lock_stat", S_IRUSR | S_IWUSR, NULL,
+		    &proc_lock_stat_operations);
 #endif
 
 	return 0;
-- 
GitLab


From 0e692a94e378628b7d527260ad939894454bcca8 Mon Sep 17 00:00:00 2001
From: Li Zefan <lizf@cn.fujitsu.com>
Date: Fri, 7 Aug 2009 15:10:54 +0800
Subject: [PATCH 0620/1153] lockdep: Fix typos in documentation

s/head/held

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <4A7BD37E.9060806@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 Documentation/lockdep-design.txt | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/Documentation/lockdep-design.txt b/Documentation/lockdep-design.txt
index e20d913d591..abf768c681e 100644
--- a/Documentation/lockdep-design.txt
+++ b/Documentation/lockdep-design.txt
@@ -30,9 +30,9 @@ State
 The validator tracks lock-class usage history into 4n + 1 separate state bits:
 
 - 'ever held in STATE context'
-- 'ever head as readlock in STATE context'
-- 'ever head with STATE enabled'
-- 'ever head as readlock with STATE enabled'
+- 'ever held as readlock in STATE context'
+- 'ever held with STATE enabled'
+- 'ever held as readlock with STATE enabled'
 
 Where STATE can be either one of (kernel/lockdep_states.h)
  - hardirq
-- 
GitLab


From 17332925d7b11bb6c2d0c49450ae58dd836005da Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@linux.ie>
Date: Fri, 7 Aug 2009 11:03:26 +1000
Subject: [PATCH 0621/1153] drm/radeon/kms: setup MC/VRAM the same way for
 suspend/resume

we should align the GTT after VRAM no matter what, as we can
come back from resume and put in a different place and bad things happen.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_device.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c
index a162ade74b7..9ff6dcb97f9 100644
--- a/drivers/gpu/drm/radeon/radeon_device.c
+++ b/drivers/gpu/drm/radeon/radeon_device.c
@@ -152,7 +152,9 @@ int radeon_mc_setup(struct radeon_device *rdev)
 		}
 	} else {
 		rdev->mc.vram_location = 0;
-		rdev->mc.gtt_location = rdev->mc.mc_vram_size;
+		tmp = rdev->mc.mc_vram_size;
+		tmp = (tmp + rdev->mc.gtt_size - 1) & ~(rdev->mc.gtt_size - 1);
+		rdev->mc.gtt_location = tmp;
 	}
 	DRM_INFO("radeon: VRAM %uM\n", rdev->mc.real_vram_size >> 20);
 	DRM_INFO("radeon: VRAM from 0x%08X to 0x%08X\n",
-- 
GitLab


From afc5e65245255a268ab22a20477ed2c9f2cdfcd3 Mon Sep 17 00:00:00 2001
From: Takashi Iwai <tiwai@suse.de>
Date: Fri, 7 Aug 2009 16:33:53 +0200
Subject: [PATCH 0622/1153] ASoC: Add missing DRV_NAME definitions for fsl/*
 drivers

Module builds are broken due to missing DRV_NAME for
efika-audio-fabric and pcm030-audio-fabric.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/soc/fsl/efika-audio-fabric.c  | 2 ++
 sound/soc/fsl/pcm030-audio-fabric.c | 2 ++
 2 files changed, 4 insertions(+)

diff --git a/sound/soc/fsl/efika-audio-fabric.c b/sound/soc/fsl/efika-audio-fabric.c
index 85b0e756950..3326e2a1e86 100644
--- a/sound/soc/fsl/efika-audio-fabric.c
+++ b/sound/soc/fsl/efika-audio-fabric.c
@@ -30,6 +30,8 @@
 #include "mpc5200_psc_ac97.h"
 #include "../codecs/stac9766.h"
 
+#define DRV_NAME "efika-audio-fabric"
+
 static struct snd_soc_device device;
 static struct snd_soc_card card;
 
diff --git a/sound/soc/fsl/pcm030-audio-fabric.c b/sound/soc/fsl/pcm030-audio-fabric.c
index 8766f7a3893..b928ef7d28e 100644
--- a/sound/soc/fsl/pcm030-audio-fabric.c
+++ b/sound/soc/fsl/pcm030-audio-fabric.c
@@ -30,6 +30,8 @@
 #include "mpc5200_psc_ac97.h"
 #include "../codecs/wm9712.h"
 
+#define DRV_NAME "pcm030-audio-fabric"
+
 static struct snd_soc_device device;
 static struct snd_soc_card card;
 
-- 
GitLab


From bd3f02212d6a457267e0c9c02c426151c436d9d4 Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Fri, 7 Aug 2009 12:49:29 +0200
Subject: [PATCH 0623/1153] ring-buffer: Fix memleak in ring_buffer_free()

I noticed oprofile memleaked in linux-2.6 current tree,
and tracked this ring-buffer leak.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
LKML-Reference: <4A7C06B9.2090302@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 kernel/trace/ring_buffer.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c
index d4d3580a894..a330513d96c 100644
--- a/kernel/trace/ring_buffer.c
+++ b/kernel/trace/ring_buffer.c
@@ -735,6 +735,7 @@ ring_buffer_free(struct ring_buffer *buffer)
 
 	put_online_cpus();
 
+	kfree(buffer->buffers);
 	free_cpumask_var(buffer->cpumask);
 
 	kfree(buffer);
-- 
GitLab


From 7dd2459d8f7a967bcd1466591aec72bb3ddc07cc Mon Sep 17 00:00:00 2001
From: Zhu Yi <yi.zhu@intel.com>
Date: Mon, 27 Jul 2009 10:10:20 +0800
Subject: [PATCH 0624/1153] ipw2x00: Write outside array bounds

> channel_index loops up to IPW_SCAN_CHANNELS, but is used after being
> incremented. This might be able to access 1 past the end of the array

Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/ipw2x00/ipw2200.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ipw2x00/ipw2200.c b/drivers/net/wireless/ipw2x00/ipw2200.c
index 44c29b3f672..6dcac73b4d2 100644
--- a/drivers/net/wireless/ipw2x00/ipw2200.c
+++ b/drivers/net/wireless/ipw2x00/ipw2200.c
@@ -6226,7 +6226,7 @@ static void ipw_add_scan_channels(struct ipw_priv *priv,
 			};
 
 			u8 channel;
-			while (channel_index < IPW_SCAN_CHANNELS) {
+			while (channel_index < IPW_SCAN_CHANNELS - 1) {
 				channel =
 				    priv->speed_scan[priv->speed_scan_pos];
 				if (channel == 0) {
-- 
GitLab


From d25f9f1357139bbdc79bc960ea84909a7c22ec2b Mon Sep 17 00:00:00 2001
From: Lennert Buytenhek <buytenh@wantstofly.org>
Date: Mon, 3 Aug 2009 21:58:26 +0200
Subject: [PATCH 0625/1153] mwl8k: fix NULL pointer dereference on receive
 out-of-memory

When we go into out-of-memory and fail to allocate skbuffs to
refill the receive ring with, rxq_process can end up running into
a receive ring entry that is marked as host-owned but doesn't have
an associated skbuff.  If this happens, we must break out of the
rx processing loop instead of trying to process the descriptor.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/mwl8k.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c
index a263d5c84c0..71f3eb67981 100644
--- a/drivers/net/wireless/mwl8k.c
+++ b/drivers/net/wireless/mwl8k.c
@@ -1012,6 +1012,8 @@ static int rxq_process(struct ieee80211_hw *hw, int index, int limit)
 		rmb();
 
 		skb = rxq->rx_skb[rxq->rx_head];
+		if (skb == NULL)
+			break;
 		rxq->rx_skb[rxq->rx_head] = NULL;
 
 		rxq->rx_head = (rxq->rx_head + 1) % MWL8K_RX_DESCS;
-- 
GitLab


From 4ff6432ea620ba467e50ec04b8271ea0eb94e62e Mon Sep 17 00:00:00 2001
From: Lennert Buytenhek <buytenh@wantstofly.org>
Date: Mon, 3 Aug 2009 21:58:39 +0200
Subject: [PATCH 0626/1153] mwl8k: add various missing GET_HW_SPEC endian
 conversions

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/mwl8k.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c
index 71f3eb67981..9643aa4751c 100644
--- a/drivers/net/wireless/mwl8k.c
+++ b/drivers/net/wireless/mwl8k.c
@@ -1656,18 +1656,18 @@ static int mwl8k_cmd_get_hw_spec(struct ieee80211_hw *hw)
 	memset(cmd->perm_addr, 0xff, sizeof(cmd->perm_addr));
 	cmd->ps_cookie = cpu_to_le32(priv->cookie_dma);
 	cmd->rx_queue_ptr = cpu_to_le32(priv->rxq[0].rx_desc_dma);
-	cmd->num_tx_queues = MWL8K_TX_QUEUES;
+	cmd->num_tx_queues = cpu_to_le32(MWL8K_TX_QUEUES);
 	for (i = 0; i < MWL8K_TX_QUEUES; i++)
 		cmd->tx_queue_ptrs[i] = cpu_to_le32(priv->txq[i].tx_desc_dma);
-	cmd->num_tx_desc_per_queue = MWL8K_TX_DESCS;
-	cmd->total_rx_desc = MWL8K_RX_DESCS;
+	cmd->num_tx_desc_per_queue = cpu_to_le32(MWL8K_TX_DESCS);
+	cmd->total_rx_desc = cpu_to_le32(MWL8K_RX_DESCS);
 
 	rc = mwl8k_post_cmd(hw, &cmd->header);
 
 	if (!rc) {
 		SET_IEEE80211_PERM_ADDR(hw, cmd->perm_addr);
 		priv->num_mcaddrs = le16_to_cpu(cmd->num_mcaddrs);
-		priv->fw_rev = cmd->fw_rev;
+		priv->fw_rev = le32_to_cpu(cmd->fw_rev);
 		priv->hw_rev = cmd->hw_rev;
 		priv->region_code = le16_to_cpu(cmd->region_code);
 	}
-- 
GitLab


From 37055bd455b31b8220c35a1ede9c6aceb791cc88 Mon Sep 17 00:00:00 2001
From: Lennert Buytenhek <buytenh@wantstofly.org>
Date: Mon, 3 Aug 2009 21:58:47 +0200
Subject: [PATCH 0627/1153] mwl8k: call pci_unmap_single() before accessing
 command structure again

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/mwl8k.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c
index 9643aa4751c..25423c05aff 100644
--- a/drivers/net/wireless/mwl8k.c
+++ b/drivers/net/wireless/mwl8k.c
@@ -1593,6 +1593,9 @@ static int mwl8k_post_cmd(struct ieee80211_hw *hw, struct mwl8k_cmd_pkt *cmd)
 	timeout = wait_for_completion_timeout(&cmd_wait,
 				msecs_to_jiffies(MWL8K_CMD_TIMEOUT_MS));
 
+	pci_unmap_single(priv->pdev, dma_addr, dma_size,
+					PCI_DMA_BIDIRECTIONAL);
+
 	result = &cmd->result;
 	if (!timeout) {
 		spin_lock_irq(&priv->fw_lock);
@@ -1612,8 +1615,6 @@ static int mwl8k_post_cmd(struct ieee80211_hw *hw, struct mwl8k_cmd_pkt *cmd)
 			       *result);
 	}
 
-	pci_unmap_single(priv->pdev, dma_addr, dma_size,
-					PCI_DMA_BIDIRECTIONAL);
 	return rc;
 }
 
-- 
GitLab


From a94cc97e14c5750ec2b50b2e4ecdfb0f369ed0f4 Mon Sep 17 00:00:00 2001
From: Lennert Buytenhek <buytenh@wantstofly.org>
Date: Mon, 3 Aug 2009 21:58:57 +0200
Subject: [PATCH 0628/1153] mwl8k: prevent crash in ->configure_filter() if no
 interface was added

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/mwl8k.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c
index 25423c05aff..6e491171f73 100644
--- a/drivers/net/wireless/mwl8k.c
+++ b/drivers/net/wireless/mwl8k.c
@@ -261,7 +261,7 @@ struct mwl8k_vif {
 	 */
 };
 
-#define MWL8K_VIF(_vif) (struct mwl8k_vif *)(&((_vif)->drv_priv))
+#define MWL8K_VIF(_vif) ((struct mwl8k_vif *)&((_vif)->drv_priv))
 
 static const struct ieee80211_channel mwl8k_channels[] = {
 	{ .center_freq = 2412, .hw_value = 1, },
@@ -3219,15 +3219,19 @@ static int mwl8k_configure_filter_wt(struct work_struct *wt)
 	struct dev_addr_list *mclist = worker->mclist;
 
 	struct mwl8k_priv *priv = hw->priv;
-	struct mwl8k_vif *mv_vif;
 	int rc = 0;
 
 	if (changed_flags & FIF_BCN_PRBRESP_PROMISC) {
 		if (*total_flags & FIF_BCN_PRBRESP_PROMISC)
 			rc = mwl8k_cmd_set_pre_scan(hw);
 		else {
-			mv_vif = MWL8K_VIF(priv->vif);
-			rc = mwl8k_cmd_set_post_scan(hw, mv_vif->bssid);
+			u8 *bssid;
+
+			bssid = "\x00\x00\x00\x00\x00\x00";
+			if (priv->vif != NULL)
+				bssid = MWL8K_VIF(priv->vif)->bssid;
+
+			rc = mwl8k_cmd_set_post_scan(hw, bssid);
 		}
 	}
 
-- 
GitLab


From 60aa569f9212a13382c29cc734f275dec0f55e0b Mon Sep 17 00:00:00 2001
From: Lennert Buytenhek <buytenh@wantstofly.org>
Date: Mon, 3 Aug 2009 21:59:09 +0200
Subject: [PATCH 0629/1153] mwl8k: prevent module unload hang

We need to unregister our ieee80211_hw before resetting the chip, as
the former causes firmware commands to be issued which will time out
once the chip has been reset.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/mwl8k.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/mwl8k.c b/drivers/net/wireless/mwl8k.c
index 6e491171f73..83967afe082 100644
--- a/drivers/net/wireless/mwl8k.c
+++ b/drivers/net/wireless/mwl8k.c
@@ -3733,6 +3733,8 @@ static void __devexit mwl8k_remove(struct pci_dev *pdev)
 
 	ieee80211_stop_queues(hw);
 
+	ieee80211_unregister_hw(hw);
+
 	/* Remove tx reclaim tasklet */
 	tasklet_kill(&priv->tx_reclaim_task);
 
@@ -3746,8 +3748,6 @@ static void __devexit mwl8k_remove(struct pci_dev *pdev)
 	for (i = 0; i < MWL8K_TX_QUEUES; i++)
 		mwl8k_txq_reclaim(hw, i, 1);
 
-	ieee80211_unregister_hw(hw);
-
 	for (i = 0; i < MWL8K_TX_QUEUES; i++)
 		mwl8k_txq_deinit(hw, i);
 
-- 
GitLab


From dd1f57ecaf9688efa69d982652ecfa3e64f1fa55 Mon Sep 17 00:00:00 2001
From: Bob Dunlop <rdunlop@guralp.com>
Date: Thu, 6 Aug 2009 12:01:03 -0400
Subject: [PATCH 0630/1153] libertas: correct packing of rxpd structure

Older Gcc compilers (3.4.5 tested) need additional hints in order to get
the packing of the rxpd structure (which contains a 16 bit union)
correct on the ARM processor.

struct txpd does not need these hints since it contains a 32 bit union
that packs naturally.

Signed-off-by: R.J.Dunlop <rdunlop@guralp.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/libertas/hostcmd.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/libertas/hostcmd.h b/drivers/net/wireless/libertas/hostcmd.h
index 0a2e29140ad..c8a1998d474 100644
--- a/drivers/net/wireless/libertas/hostcmd.h
+++ b/drivers/net/wireless/libertas/hostcmd.h
@@ -56,8 +56,8 @@ struct rxpd {
 			u8 bss_type;
 			/* BSS number */
 			u8 bss_num;
-		} bss;
-	} u;
+		} __attribute__ ((packed)) bss;
+	} __attribute__ ((packed)) u;
 
 	/* SNR */
 	u8 snr;
-- 
GitLab


From d25f14389a65c7f95512b01415d8d4a8d62855ab Mon Sep 17 00:00:00 2001
From: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Date: Mon, 27 Jul 2009 12:05:38 +0900
Subject: [PATCH 0631/1153] PCI hotplug: SGI hotplug: fix build failure

The commit bd3d99c17039fd05a29587db3f4a180c48da115a ("PCI: Remove
untested Electromechanical Interlock (EMI) support in pciehp."), which
removes the definition of "struct hotplug_slot_attr", broke SGI
hotplug driver. By this commit, we get the following compile error.

drivers/pci/hotplug/sgi_hotplug.c:106: error: variable 'sn_slot_path_attr' has initializer but incomplete type
drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'attr' specified in initializer
drivers/pci/hotplug/sgi_hotplug.c:106: error: extra brace group at end of initializer
drivers/pci/hotplug/sgi_hotplug.c:106: error: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'show' specified in initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hp_destroy':
drivers/pci/hotplug/sgi_hotplug.c:203: error: invalid use of undefined type 'struct hotplug_slot_attribute'
drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hotplug_slot_register':
drivers/pci/hotplug/sgi_hotplug.c:655: error: invalid use of undefined type 'struct hotplug_slot_attribute'

This patch fixes this regression by adding the definition of struct
hotplug_slot_attr into sgi_hotplug.c.

Tested-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
---
 drivers/pci/hotplug/sgi_hotplug.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/pci/hotplug/sgi_hotplug.c b/drivers/pci/hotplug/sgi_hotplug.c
index a4494d78e7c..0a724bb6ba1 100644
--- a/drivers/pci/hotplug/sgi_hotplug.c
+++ b/drivers/pci/hotplug/sgi_hotplug.c
@@ -103,6 +103,12 @@ static ssize_t path_show (struct hotplug_slot *bss_hotplug_slot,
 	return retval;
 }
 
+struct hotplug_slot_attribute {
+	struct attribute attr;
+	ssize_t (*show)(struct hotplug_slot *, char *);
+	ssize_t (*store)(struct hotplug_slot *, const char *, size_t);
+};
+
 static struct hotplug_slot_attribute sn_slot_path_attr = __ATTR_RO(path);
 
 static int sn_pci_slot_valid(struct pci_bus *pci_bus, int device)
-- 
GitLab


From 94f81a47c4a7a2d7a16fcfdd6d81da381732c101 Mon Sep 17 00:00:00 2001
From: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Date: Mon, 27 Jul 2009 12:06:46 +0900
Subject: [PATCH 0632/1153] PCI hotplug: SGI hotplug: do not use
 hotplug_slot_attr

By the pci slot changes, callbacks of attributes under slot directory
(/sys/bus/pci/slots) had been changed to get the pointer to struct
pci_slot instead of struct hotplug_slot. So the path_show() that
assumes the parameter is a pointer to struct hotplug_slot seems
broken.

Tested-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
---
 drivers/pci/hotplug/sgi_hotplug.c | 13 +++----------
 1 file changed, 3 insertions(+), 10 deletions(-)

diff --git a/drivers/pci/hotplug/sgi_hotplug.c b/drivers/pci/hotplug/sgi_hotplug.c
index 0a724bb6ba1..8aebe1e9d3d 100644
--- a/drivers/pci/hotplug/sgi_hotplug.c
+++ b/drivers/pci/hotplug/sgi_hotplug.c
@@ -90,11 +90,10 @@ static struct hotplug_slot_ops sn_hotplug_slot_ops = {
 
 static DEFINE_MUTEX(sn_hotplug_mutex);
 
-static ssize_t path_show (struct hotplug_slot *bss_hotplug_slot,
-	       		  char *buf)
+static ssize_t path_show(struct pci_slot *pci_slot, char *buf)
 {
 	int retval = -ENOENT;
-	struct slot *slot = bss_hotplug_slot->private;
+	struct slot *slot = pci_slot->hotplug->private;
 
 	if (!slot)
 		return retval;
@@ -103,13 +102,7 @@ static ssize_t path_show (struct hotplug_slot *bss_hotplug_slot,
 	return retval;
 }
 
-struct hotplug_slot_attribute {
-	struct attribute attr;
-	ssize_t (*show)(struct hotplug_slot *, char *);
-	ssize_t (*store)(struct hotplug_slot *, const char *, size_t);
-};
-
-static struct hotplug_slot_attribute sn_slot_path_attr = __ATTR_RO(path);
+static struct pci_slot_attribute sn_slot_path_attr = __ATTR_RO(path);
 
 static int sn_pci_slot_valid(struct pci_bus *pci_bus, int device)
 {
-- 
GitLab


From 54e346215e4fe2ca8c94c54e546cc61902060510 Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@lst.de>
Date: Fri, 7 Aug 2009 14:38:25 -0300
Subject: [PATCH 0633/1153] vfs: fix inode_init_always calling convention

Currently inode_init_always calls into ->destroy_inode if the additional
initialization fails.  That's not only counter-intuitive because
inode_init_always did not allocate the inode structure, but in case of
XFS it's actively harmful as ->destroy_inode might delete the inode from
a radix-tree that has never been added.  This in turn might end up
deleting the inode for the same inum that has been instanciated by
another process and cause lots of cause subtile problems.

Also in the case of re-initializing a reclaimable inode in XFS it would
free an inode we still want to keep alive.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
---
 fs/inode.c         | 30 +++++++++++++++++-------------
 fs/xfs/xfs_iget.c  | 17 +++++------------
 include/linux/fs.h |  2 +-
 3 files changed, 23 insertions(+), 26 deletions(-)

diff --git a/fs/inode.c b/fs/inode.c
index 901bad1e5f1..af2c05235cc 100644
--- a/fs/inode.c
+++ b/fs/inode.c
@@ -120,12 +120,11 @@ static void wake_up_inode(struct inode *inode)
  * These are initializations that need to be done on every inode
  * allocation as the fields are not initialised by slab allocation.
  */
-struct inode *inode_init_always(struct super_block *sb, struct inode *inode)
+int inode_init_always(struct super_block *sb, struct inode *inode)
 {
 	static const struct address_space_operations empty_aops;
 	static struct inode_operations empty_iops;
 	static const struct file_operations empty_fops;
-
 	struct address_space *const mapping = &inode->i_data;
 
 	inode->i_sb = sb;
@@ -152,7 +151,7 @@ struct inode *inode_init_always(struct super_block *sb, struct inode *inode)
 	inode->dirtied_when = 0;
 
 	if (security_inode_alloc(inode))
-		goto out_free_inode;
+		goto out;
 
 	/* allocate and initialize an i_integrity */
 	if (ima_inode_alloc(inode))
@@ -198,16 +197,12 @@ struct inode *inode_init_always(struct super_block *sb, struct inode *inode)
 	inode->i_fsnotify_mask = 0;
 #endif
 
-	return inode;
+	return 0;
 
 out_free_security:
 	security_inode_free(inode);
-out_free_inode:
-	if (inode->i_sb->s_op->destroy_inode)
-		inode->i_sb->s_op->destroy_inode(inode);
-	else
-		kmem_cache_free(inode_cachep, (inode));
-	return NULL;
+out:
+	return -ENOMEM;
 }
 EXPORT_SYMBOL(inode_init_always);
 
@@ -220,9 +215,18 @@ static struct inode *alloc_inode(struct super_block *sb)
 	else
 		inode = kmem_cache_alloc(inode_cachep, GFP_KERNEL);
 
-	if (inode)
-		return inode_init_always(sb, inode);
-	return NULL;
+	if (!inode)
+		return NULL;
+
+	if (unlikely(inode_init_always(sb, inode))) {
+		if (inode->i_sb->s_op->destroy_inode)
+			inode->i_sb->s_op->destroy_inode(inode);
+		else
+			kmem_cache_free(inode_cachep, inode);
+		return NULL;
+	}
+
+	return inode;
 }
 
 void destroy_inode(struct inode *inode)
diff --git a/fs/xfs/xfs_iget.c b/fs/xfs/xfs_iget.c
index 5fcec6f020a..719c85b155f 100644
--- a/fs/xfs/xfs_iget.c
+++ b/fs/xfs/xfs_iget.c
@@ -64,6 +64,10 @@ xfs_inode_alloc(
 	ip = kmem_zone_alloc(xfs_inode_zone, KM_SLEEP);
 	if (!ip)
 		return NULL;
+	if (inode_init_always(mp->m_super, VFS_I(ip))) {
+		kmem_zone_free(xfs_inode_zone, ip);
+		return NULL;
+	}
 
 	ASSERT(atomic_read(&ip->i_iocount) == 0);
 	ASSERT(atomic_read(&ip->i_pincount) == 0);
@@ -105,17 +109,6 @@ xfs_inode_alloc(
 #ifdef XFS_DIR2_TRACE
 	ip->i_dir_trace = ktrace_alloc(XFS_DIR2_KTRACE_SIZE, KM_NOFS);
 #endif
-	/*
-	* Now initialise the VFS inode. We do this after the xfs_inode
-	* initialisation as internal failures will result in ->destroy_inode
-	* being called and that will pass down through the reclaim path and
-	* free the XFS inode. This path requires the XFS inode to already be
-	* initialised. Hence if this call fails, the xfs_inode has already
-	* been freed and we should not reference it at all in the error
-	* handling.
-	*/
-	if (!inode_init_always(mp->m_super, VFS_I(ip)))
-		return NULL;
 
 	/* prevent anyone from using this yet */
 	VFS_I(ip)->i_state = I_NEW|I_LOCK;
@@ -167,7 +160,7 @@ xfs_iget_cache_hit(
 		 * errors cleanly, then tag it so it can be set up correctly
 		 * later.
 		 */
-		if (!inode_init_always(mp->m_super, VFS_I(ip))) {
+		if (inode_init_always(mp->m_super, VFS_I(ip))) {
 			error = ENOMEM;
 			goto out_error;
 		}
diff --git a/include/linux/fs.h b/include/linux/fs.h
index a36ffa5a77a..0c3b5e58a98 100644
--- a/include/linux/fs.h
+++ b/include/linux/fs.h
@@ -2137,7 +2137,7 @@ extern loff_t default_llseek(struct file *file, loff_t offset, int origin);
 
 extern loff_t vfs_llseek(struct file *file, loff_t offset, int origin);
 
-extern struct inode * inode_init_always(struct super_block *, struct inode *);
+extern int inode_init_always(struct super_block *, struct inode *);
 extern void inode_init_once(struct inode *);
 extern void inode_add_to_lists(struct super_block *, struct inode *);
 extern void iput(struct inode *);
-- 
GitLab


From 2e00c97e2c1d2ffc9e26252ca26b237678b0b772 Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@lst.de>
Date: Fri, 7 Aug 2009 14:38:29 -0300
Subject: [PATCH 0634/1153] vfs: add __destroy_inode

When we want to tear down an inode that lost the add to the cache race
in XFS we must not call into ->destroy_inode because that would delete
the inode that won the race from the inode cache radix tree.

This patch provides the __destroy_inode helper needed to fix this,
the actual fix will be in th next patch.  As XFS was the only reason
destroy_inode was exported we shift the export to the new __destroy_inode.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
---
 fs/inode.c         | 10 +++++++---
 include/linux/fs.h |  1 +
 2 files changed, 8 insertions(+), 3 deletions(-)

diff --git a/fs/inode.c b/fs/inode.c
index af2c05235cc..ae7b67e4866 100644
--- a/fs/inode.c
+++ b/fs/inode.c
@@ -229,7 +229,7 @@ static struct inode *alloc_inode(struct super_block *sb)
 	return inode;
 }
 
-void destroy_inode(struct inode *inode)
+void __destroy_inode(struct inode *inode)
 {
 	BUG_ON(inode_has_buffers(inode));
 	ima_inode_free(inode);
@@ -241,13 +241,17 @@ void destroy_inode(struct inode *inode)
 	if (inode->i_default_acl && inode->i_default_acl != ACL_NOT_CACHED)
 		posix_acl_release(inode->i_default_acl);
 #endif
+}
+EXPORT_SYMBOL(__destroy_inode);
+
+void destroy_inode(struct inode *inode)
+{
+	__destroy_inode(inode);
 	if (inode->i_sb->s_op->destroy_inode)
 		inode->i_sb->s_op->destroy_inode(inode);
 	else
 		kmem_cache_free(inode_cachep, (inode));
 }
-EXPORT_SYMBOL(destroy_inode);
-
 
 /*
  * These are initializations that only need to be done
diff --git a/include/linux/fs.h b/include/linux/fs.h
index 0c3b5e58a98..67888a9e065 100644
--- a/include/linux/fs.h
+++ b/include/linux/fs.h
@@ -2164,6 +2164,7 @@ extern void __iget(struct inode * inode);
 extern void iget_failed(struct inode *);
 extern void clear_inode(struct inode *);
 extern void destroy_inode(struct inode *);
+extern void __destroy_inode(struct inode *);
 extern struct inode *new_inode(struct super_block *);
 extern int should_remove_suid(struct dentry *);
 extern int file_remove_suid(struct file *);
-- 
GitLab


From b36ec0428a06fcbdb67d61e9e664154e5dd9a8c7 Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@lst.de>
Date: Fri, 7 Aug 2009 14:38:34 -0300
Subject: [PATCH 0635/1153] xfs: fix freeing of inodes not yet added to the
 inode cache

When freeing an inode that lost race getting added to the inode cache we
must not call into ->destroy_inode, because that would delete the inode
that won the race from the inode cache radix tree.

This patch uses splits a new xfs_inode_free helper out of xfs_ireclaim
and uses that plus __destroy_inode to make sure we really only free
the memory allocted for the inode that lost the race, and not mess with
the inode cache state.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reported-by: Alex Samad <alex@samad.com.au>
Reported-by: Andrew Randrianasulu <randrik@mail.ru>
Reported-by: Stephane <sharnois@max-t.com>
Reported-by: Tommy <tommy@news-service.com>
Reported-by: Miah Gregory <mace@darksilence.net>
Reported-by: Gabriel Barazer <gabriel@oxeva.fr>
Reported-by: Leandro Lucarella <llucax@gmail.com>
Reported-by: Daniel Burr <dburr@fami.com.au>
Reported-by: Nickolay <newmail@spaces.ru>
Reported-by: Michael Guntsche <mike@it-loops.com>
Reported-by: Dan Carley <dan.carley+linuxkern-bugs@gmail.com>
Reported-by: Michael Ole Olsen <gnu@gmx.net>
Reported-by: Michael Weissenbacher <mw@dermichi.com>
Reported-by: Martin Spott <Martin.Spott@mgras.net>
Reported-by: Christian Kujau <lists@nerdbynature.de>
Tested-by: Michael Guntsche <mike@it-loops.com>
Tested-by: Dan Carley <dan.carley+linuxkern-bugs@gmail.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
---
 fs/xfs/xfs_iget.c  | 125 ++++++++++++++++++++++++---------------------
 fs/xfs/xfs_inode.h |  17 ------
 2 files changed, 68 insertions(+), 74 deletions(-)

diff --git a/fs/xfs/xfs_iget.c b/fs/xfs/xfs_iget.c
index 719c85b155f..34ec86923f7 100644
--- a/fs/xfs/xfs_iget.c
+++ b/fs/xfs/xfs_iget.c
@@ -116,6 +116,71 @@ xfs_inode_alloc(
 	return ip;
 }
 
+STATIC void
+xfs_inode_free(
+	struct xfs_inode	*ip)
+{
+	switch (ip->i_d.di_mode & S_IFMT) {
+	case S_IFREG:
+	case S_IFDIR:
+	case S_IFLNK:
+		xfs_idestroy_fork(ip, XFS_DATA_FORK);
+		break;
+	}
+
+	if (ip->i_afp)
+		xfs_idestroy_fork(ip, XFS_ATTR_FORK);
+
+#ifdef XFS_INODE_TRACE
+	ktrace_free(ip->i_trace);
+#endif
+#ifdef XFS_BMAP_TRACE
+	ktrace_free(ip->i_xtrace);
+#endif
+#ifdef XFS_BTREE_TRACE
+	ktrace_free(ip->i_btrace);
+#endif
+#ifdef XFS_RW_TRACE
+	ktrace_free(ip->i_rwtrace);
+#endif
+#ifdef XFS_ILOCK_TRACE
+	ktrace_free(ip->i_lock_trace);
+#endif
+#ifdef XFS_DIR2_TRACE
+	ktrace_free(ip->i_dir_trace);
+#endif
+
+	if (ip->i_itemp) {
+		/*
+		 * Only if we are shutting down the fs will we see an
+		 * inode still in the AIL. If it is there, we should remove
+		 * it to prevent a use-after-free from occurring.
+		 */
+		xfs_log_item_t	*lip = &ip->i_itemp->ili_item;
+		struct xfs_ail	*ailp = lip->li_ailp;
+
+		ASSERT(((lip->li_flags & XFS_LI_IN_AIL) == 0) ||
+				       XFS_FORCED_SHUTDOWN(ip->i_mount));
+		if (lip->li_flags & XFS_LI_IN_AIL) {
+			spin_lock(&ailp->xa_lock);
+			if (lip->li_flags & XFS_LI_IN_AIL)
+				xfs_trans_ail_delete(ailp, lip);
+			else
+				spin_unlock(&ailp->xa_lock);
+		}
+		xfs_inode_item_destroy(ip);
+		ip->i_itemp = NULL;
+	}
+
+	/* asserts to verify all state is correct here */
+	ASSERT(atomic_read(&ip->i_iocount) == 0);
+	ASSERT(atomic_read(&ip->i_pincount) == 0);
+	ASSERT(!spin_is_locked(&ip->i_flags_lock));
+	ASSERT(completion_done(&ip->i_flush));
+
+	kmem_zone_free(xfs_inode_zone, ip);
+}
+
 /*
  * Check the validity of the inode we just found it the cache
  */
@@ -292,7 +357,8 @@ out_preload_end:
 	if (lock_flags)
 		xfs_iunlock(ip, lock_flags);
 out_destroy:
-	xfs_destroy_inode(ip);
+	__destroy_inode(VFS_I(ip));
+	xfs_inode_free(ip);
 	return error;
 }
 
@@ -497,62 +563,7 @@ xfs_ireclaim(
 	xfs_qm_dqdetach(ip);
 	xfs_iunlock(ip, XFS_ILOCK_EXCL | XFS_IOLOCK_EXCL);
 
-	switch (ip->i_d.di_mode & S_IFMT) {
-	case S_IFREG:
-	case S_IFDIR:
-	case S_IFLNK:
-		xfs_idestroy_fork(ip, XFS_DATA_FORK);
-		break;
-	}
-
-	if (ip->i_afp)
-		xfs_idestroy_fork(ip, XFS_ATTR_FORK);
-
-#ifdef XFS_INODE_TRACE
-	ktrace_free(ip->i_trace);
-#endif
-#ifdef XFS_BMAP_TRACE
-	ktrace_free(ip->i_xtrace);
-#endif
-#ifdef XFS_BTREE_TRACE
-	ktrace_free(ip->i_btrace);
-#endif
-#ifdef XFS_RW_TRACE
-	ktrace_free(ip->i_rwtrace);
-#endif
-#ifdef XFS_ILOCK_TRACE
-	ktrace_free(ip->i_lock_trace);
-#endif
-#ifdef XFS_DIR2_TRACE
-	ktrace_free(ip->i_dir_trace);
-#endif
-	if (ip->i_itemp) {
-		/*
-		 * Only if we are shutting down the fs will we see an
-		 * inode still in the AIL. If it is there, we should remove
-		 * it to prevent a use-after-free from occurring.
-		 */
-		xfs_log_item_t	*lip = &ip->i_itemp->ili_item;
-		struct xfs_ail	*ailp = lip->li_ailp;
-
-		ASSERT(((lip->li_flags & XFS_LI_IN_AIL) == 0) ||
-				       XFS_FORCED_SHUTDOWN(ip->i_mount));
-		if (lip->li_flags & XFS_LI_IN_AIL) {
-			spin_lock(&ailp->xa_lock);
-			if (lip->li_flags & XFS_LI_IN_AIL)
-				xfs_trans_ail_delete(ailp, lip);
-			else
-				spin_unlock(&ailp->xa_lock);
-		}
-		xfs_inode_item_destroy(ip);
-		ip->i_itemp = NULL;
-	}
-	/* asserts to verify all state is correct here */
-	ASSERT(atomic_read(&ip->i_iocount) == 0);
-	ASSERT(atomic_read(&ip->i_pincount) == 0);
-	ASSERT(!spin_is_locked(&ip->i_flags_lock));
-	ASSERT(completion_done(&ip->i_flush));
-	kmem_zone_free(xfs_inode_zone, ip);
+	xfs_inode_free(ip);
 }
 
 /*
diff --git a/fs/xfs/xfs_inode.h b/fs/xfs/xfs_inode.h
index 1804f866a71..65f24a3cc99 100644
--- a/fs/xfs/xfs_inode.h
+++ b/fs/xfs/xfs_inode.h
@@ -309,23 +309,6 @@ static inline struct inode *VFS_I(struct xfs_inode *ip)
 	return &ip->i_vnode;
 }
 
-/*
- * Get rid of a partially initialized inode.
- *
- * We have to go through destroy_inode to make sure allocations
- * from init_inode_always like the security data are undone.
- *
- * We mark the inode bad so that it takes the short cut in
- * the reclaim path instead of going through the flush path
- * which doesn't make sense for an inode that has never seen the
- * light of day.
- */
-static inline void xfs_destroy_inode(struct xfs_inode *ip)
-{
-	make_bad_inode(VFS_I(ip));
-	return destroy_inode(VFS_I(ip));
-}
-
 /*
  * i_flags helper functions
  */
-- 
GitLab


From 2020002a878403a6858868d85a43623f74859dba Mon Sep 17 00:00:00 2001
From: Stoyan Gaydarov <sgayda2@uiuc.edu>
Date: Thu, 6 Aug 2009 15:07:28 -0700
Subject: [PATCH 0636/1153] drivers/w1/masters/omap_hdq.c: fix missing mutex
 unlock

This was found using a semantic patch, more info can be found at:
http://www.emn.fr/x-info/coccinelle/

Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/w1/masters/omap_hdq.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/w1/masters/omap_hdq.c b/drivers/w1/masters/omap_hdq.c
index a7e3b706b9d..0d92969404c 100644
--- a/drivers/w1/masters/omap_hdq.c
+++ b/drivers/w1/masters/omap_hdq.c
@@ -687,6 +687,7 @@ static int omap_hdq_remove(struct platform_device *pdev)
 
 	if (hdq_data->hdq_usecount) {
 		dev_dbg(&pdev->dev, "removed when use count is not zero\n");
+		mutex_unlock(&hdq_data->hdq_mutex);
 		return -EBUSY;
 	}
 
-- 
GitLab


From 69dd647f969c28d18de77e2153f30d05a1874571 Mon Sep 17 00:00:00 2001
From: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Date: Thu, 6 Aug 2009 15:07:29 -0700
Subject: [PATCH 0637/1153] generic-ipi: fix hotplug_cfd()

Use CONFIG_HOTPLUG_CPU, not CONFIG_CPU_HOTPLUG

When hot-unpluging a cpu, it will leak memory allocated at cpu hotplug,
but only if CPUMASK_OFFSTACK=y, which is default to n.

The bug was introduced by 8969a5ede0f9e17da4b943712429aef2c9bcd82b
("generic-ipi: remove kmalloc()").

Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/smp.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/smp.c b/kernel/smp.c
index ad63d850120..94188b8ecc3 100644
--- a/kernel/smp.c
+++ b/kernel/smp.c
@@ -57,7 +57,7 @@ hotplug_cfd(struct notifier_block *nfb, unsigned long action, void *hcpu)
 			return NOTIFY_BAD;
 		break;
 
-#ifdef CONFIG_CPU_HOTPLUG
+#ifdef CONFIG_HOTPLUG_CPU
 	case CPU_UP_CANCELED:
 	case CPU_UP_CANCELED_FROZEN:
 
-- 
GitLab


From 93274e4d4e9416ad1fa47e2f26011e2c483fe5fe Mon Sep 17 00:00:00 2001
From: Stefani Seibold <stefani@seibold.net>
Date: Thu, 6 Aug 2009 15:07:30 -0700
Subject: [PATCH 0638/1153] fbcon: fix rotate upside down crash

Fix the rotate_ud() function not to crash in case of a font which has not
a width of multiple by 8: The inner loop of the font pixel copy should not
access a bit outside the font memory area.  Subtract the shift offset from
the font width will prevent this.

Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/video/console/fbcon_rotate.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/video/console/fbcon_rotate.h b/drivers/video/console/fbcon_rotate.h
index 75be5ce53dc..e233444cda6 100644
--- a/drivers/video/console/fbcon_rotate.h
+++ b/drivers/video/console/fbcon_rotate.h
@@ -45,7 +45,7 @@ static inline void rotate_ud(const char *in, char *out, u32 width, u32 height)
 	width = (width + 7) & ~7;
 
 	for (i = 0; i < height; i++) {
-		for (j = 0; j < width; j++) {
+		for (j = 0; j < width - shift; j++) {
 			if (pattern_test_bit(j, i, width, in))
 				pattern_set_bit(width - (1 + j + shift),
 						height - (1 + i),
-- 
GitLab


From 4bfc44958e499af9a73f62201543b3a1f617cfeb Mon Sep 17 00:00:00 2001
From: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Date: Thu, 6 Aug 2009 15:07:33 -0700
Subject: [PATCH 0639/1153] mm: make set_mempolicy(MPOL_INTERLEAV)
 N_HIGH_MEMORY aware

At first, init_task's mems_allowed is initialized as this.
 init_task->mems_allowed == node_state[N_POSSIBLE]

And cpuset's top_cpuset mask is initialized as this
 top_cpuset->mems_allowed = node_state[N_HIGH_MEMORY]

Before 2.6.29:
policy's mems_allowed is initialized as this.

  1. update tasks->mems_allowed by its cpuset->mems_allowed.
  2. policy->mems_allowed = nodes_and(tasks->mems_allowed, user's mask)

Updating task's mems_allowed in reference to top_cpuset's one.
cpuset's mems_allowed is aware of N_HIGH_MEMORY, always.

In 2.6.30: After commit 58568d2a8215cb6f55caf2332017d7bdff954e1c
("cpuset,mm: update tasks' mems_allowed in time"), policy's mems_allowed
is initialized as this.

  1. policy->mems_allowd = nodes_and(task->mems_allowed, user's mask)

Here, if task is in top_cpuset, task->mems_allowed is not updated from
init's one.  Assume user excutes command as #numactrl --interleave=all
,....

  policy->mems_allowd = nodes_and(N_POSSIBLE, ALL_SET_MASK)

Then, policy's mems_allowd can includes a possible node, which has no pgdat.

MPOL's INTERLEAVE just scans nodemask of task->mems_allowd and access this
directly.

  NODE_DATA(nid)->zonelist even if NODE_DATA(nid)==NULL

Then, what's we need is making policy->mems_allowed be aware of
N_HIGH_MEMORY.  This patch does that.  But to do so, extra nodemask will
be on statck.  Because I know cpumask has a new interface of
CPUMASK_ALLOC(), I added it to node.

This patch stands on old behavior.  But I feel this fix itself is just a
Band-Aid.  But to do fundametal fix, we have to take care of memory
hotplug and it takes time.  (task->mems_allowd should be N_HIGH_MEMORY, I
think.)

mpol_set_nodemask() should be aware of N_HIGH_MEMORY and policy's nodemask
should be includes only online nodes.

In old behavior, this is guaranteed by frequent reference to cpuset's
code.  Now, most of them are removed and mempolicy has to check it by
itself.

To do check, a few nodemask_t will be used for calculating nodemask.  But,
size of nodemask_t can be big and it's not good to allocate them on stack.

Now, cpumask_t has CPUMASK_ALLOC/FREE an easy code for get scratch area.
NODEMASK_ALLOC/FREE shoudl be there.

[akpm@linux-foundation.org: cleanups & tweaks]
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Paul Menage <menage@google.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: David Rientjes <rientjes@google.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/nodemask.h | 28 ++++++++++++++
 mm/mempolicy.c           | 84 +++++++++++++++++++++++++++-------------
 2 files changed, 86 insertions(+), 26 deletions(-)

diff --git a/include/linux/nodemask.h b/include/linux/nodemask.h
index 829b94b156f..b359c4a9ec9 100644
--- a/include/linux/nodemask.h
+++ b/include/linux/nodemask.h
@@ -82,6 +82,12 @@
  *    to generate slightly worse code.  So use a simple one-line #define
  *    for node_isset(), instead of wrapping an inline inside a macro, the
  *    way we do the other calls.
+ *
+ * NODEMASK_SCRATCH
+ * When doing above logical AND, OR, XOR, Remap operations the callers tend to
+ * need temporary nodemask_t's on the stack. But if NODES_SHIFT is large,
+ * nodemask_t's consume too much stack space.  NODEMASK_SCRATCH is a helper
+ * for such situations. See below and CPUMASK_ALLOC also.
  */
 
 #include <linux/kernel.h>
@@ -473,4 +479,26 @@ static inline int num_node_state(enum node_states state)
 #define for_each_node(node)	   for_each_node_state(node, N_POSSIBLE)
 #define for_each_online_node(node) for_each_node_state(node, N_ONLINE)
 
+/*
+ * For nodemask scrach area.(See CPUMASK_ALLOC() in cpumask.h)
+ */
+
+#if NODES_SHIFT > 8 /* nodemask_t > 64 bytes */
+#define NODEMASK_ALLOC(x, m) struct x *m = kmalloc(sizeof(*m), GFP_KERNEL)
+#define NODEMASK_FREE(m) kfree(m)
+#else
+#define NODEMASK_ALLOC(x, m) struct x _m, *m = &_m
+#define NODEMASK_FREE(m)
+#endif
+
+/* A example struture for using NODEMASK_ALLOC, used in mempolicy. */
+struct nodemask_scratch {
+	nodemask_t	mask1;
+	nodemask_t	mask2;
+};
+
+#define NODEMASK_SCRATCH(x) NODEMASK_ALLOC(nodemask_scratch, x)
+#define NODEMASK_SCRATCH_FREE(x)  NODEMASK_FREE(x)
+
+
 #endif /* __LINUX_NODEMASK_H */
diff --git a/mm/mempolicy.c b/mm/mempolicy.c
index e08e2c4da63..7dd9d9f8069 100644
--- a/mm/mempolicy.c
+++ b/mm/mempolicy.c
@@ -191,25 +191,27 @@ static int mpol_new_bind(struct mempolicy *pol, const nodemask_t *nodes)
  * Must be called holding task's alloc_lock to protect task's mems_allowed
  * and mempolicy.  May also be called holding the mmap_semaphore for write.
  */
-static int mpol_set_nodemask(struct mempolicy *pol, const nodemask_t *nodes)
+static int mpol_set_nodemask(struct mempolicy *pol,
+		     const nodemask_t *nodes, struct nodemask_scratch *nsc)
 {
-	nodemask_t cpuset_context_nmask;
 	int ret;
 
 	/* if mode is MPOL_DEFAULT, pol is NULL. This is right. */
 	if (pol == NULL)
 		return 0;
+	/* Check N_HIGH_MEMORY */
+	nodes_and(nsc->mask1,
+		  cpuset_current_mems_allowed, node_states[N_HIGH_MEMORY]);
 
 	VM_BUG_ON(!nodes);
 	if (pol->mode == MPOL_PREFERRED && nodes_empty(*nodes))
 		nodes = NULL;	/* explicit local allocation */
 	else {
 		if (pol->flags & MPOL_F_RELATIVE_NODES)
-			mpol_relative_nodemask(&cpuset_context_nmask, nodes,
-					       &cpuset_current_mems_allowed);
+			mpol_relative_nodemask(&nsc->mask2, nodes,&nsc->mask1);
 		else
-			nodes_and(cpuset_context_nmask, *nodes,
-				  cpuset_current_mems_allowed);
+			nodes_and(nsc->mask2, *nodes, nsc->mask1);
+
 		if (mpol_store_user_nodemask(pol))
 			pol->w.user_nodemask = *nodes;
 		else
@@ -217,8 +219,10 @@ static int mpol_set_nodemask(struct mempolicy *pol, const nodemask_t *nodes)
 						cpuset_current_mems_allowed;
 	}
 
-	ret = mpol_ops[pol->mode].create(pol,
-				nodes ? &cpuset_context_nmask : NULL);
+	if (nodes)
+		ret = mpol_ops[pol->mode].create(pol, &nsc->mask2);
+	else
+		ret = mpol_ops[pol->mode].create(pol, NULL);
 	return ret;
 }
 
@@ -620,12 +624,17 @@ static long do_set_mempolicy(unsigned short mode, unsigned short flags,
 {
 	struct mempolicy *new, *old;
 	struct mm_struct *mm = current->mm;
+	NODEMASK_SCRATCH(scratch);
 	int ret;
 
-	new = mpol_new(mode, flags, nodes);
-	if (IS_ERR(new))
-		return PTR_ERR(new);
+	if (!scratch)
+		return -ENOMEM;
 
+	new = mpol_new(mode, flags, nodes);
+	if (IS_ERR(new)) {
+		ret = PTR_ERR(new);
+		goto out;
+	}
 	/*
 	 * prevent changing our mempolicy while show_numa_maps()
 	 * is using it.
@@ -635,13 +644,13 @@ static long do_set_mempolicy(unsigned short mode, unsigned short flags,
 	if (mm)
 		down_write(&mm->mmap_sem);
 	task_lock(current);
-	ret = mpol_set_nodemask(new, nodes);
+	ret = mpol_set_nodemask(new, nodes, scratch);
 	if (ret) {
 		task_unlock(current);
 		if (mm)
 			up_write(&mm->mmap_sem);
 		mpol_put(new);
-		return ret;
+		goto out;
 	}
 	old = current->mempolicy;
 	current->mempolicy = new;
@@ -654,7 +663,10 @@ static long do_set_mempolicy(unsigned short mode, unsigned short flags,
 		up_write(&mm->mmap_sem);
 
 	mpol_put(old);
-	return 0;
+	ret = 0;
+out:
+	NODEMASK_SCRATCH_FREE(scratch);
+	return ret;
 }
 
 /*
@@ -1014,12 +1026,20 @@ static long do_mbind(unsigned long start, unsigned long len,
 		if (err)
 			return err;
 	}
-	down_write(&mm->mmap_sem);
-	task_lock(current);
-	err = mpol_set_nodemask(new, nmask);
-	task_unlock(current);
+	{
+		NODEMASK_SCRATCH(scratch);
+		if (scratch) {
+			down_write(&mm->mmap_sem);
+			task_lock(current);
+			err = mpol_set_nodemask(new, nmask, scratch);
+			task_unlock(current);
+			if (err)
+				up_write(&mm->mmap_sem);
+		} else
+			err = -ENOMEM;
+		NODEMASK_SCRATCH_FREE(scratch);
+	}
 	if (err) {
-		up_write(&mm->mmap_sem);
 		mpol_put(new);
 		return err;
 	}
@@ -1891,6 +1911,7 @@ restart:
  * Install non-NULL @mpol in inode's shared policy rb-tree.
  * On entry, the current task has a reference on a non-NULL @mpol.
  * This must be released on exit.
+ * This is called at get_inode() calls and we can use GFP_KERNEL.
  */
 void mpol_shared_policy_init(struct shared_policy *sp, struct mempolicy *mpol)
 {
@@ -1902,19 +1923,24 @@ void mpol_shared_policy_init(struct shared_policy *sp, struct mempolicy *mpol)
 	if (mpol) {
 		struct vm_area_struct pvma;
 		struct mempolicy *new;
+		NODEMASK_SCRATCH(scratch);
 
+		if (!scratch)
+			return;
 		/* contextualize the tmpfs mount point mempolicy */
 		new = mpol_new(mpol->mode, mpol->flags, &mpol->w.user_nodemask);
 		if (IS_ERR(new)) {
 			mpol_put(mpol);	/* drop our ref on sb mpol */
+			NODEMASK_SCRATCH_FREE(scratch);
 			return;		/* no valid nodemask intersection */
 		}
 
 		task_lock(current);
-		ret = mpol_set_nodemask(new, &mpol->w.user_nodemask);
+		ret = mpol_set_nodemask(new, &mpol->w.user_nodemask, scratch);
 		task_unlock(current);
 		mpol_put(mpol);	/* drop our ref on sb mpol */
 		if (ret) {
+			NODEMASK_SCRATCH_FREE(scratch);
 			mpol_put(new);
 			return;
 		}
@@ -1924,6 +1950,7 @@ void mpol_shared_policy_init(struct shared_policy *sp, struct mempolicy *mpol)
 		pvma.vm_end = TASK_SIZE;	/* policy covers entire file */
 		mpol_set_shared_policy(sp, &pvma, new); /* adds ref */
 		mpol_put(new);			/* drop initial ref */
+		NODEMASK_SCRATCH_FREE(scratch);
 	}
 }
 
@@ -2140,13 +2167,18 @@ int mpol_parse_str(char *str, struct mempolicy **mpol, int no_context)
 		err = 1;
 	else {
 		int ret;
-
-		task_lock(current);
-		ret = mpol_set_nodemask(new, &nodes);
-		task_unlock(current);
-		if (ret)
+		NODEMASK_SCRATCH(scratch);
+		if (scratch) {
+			task_lock(current);
+			ret = mpol_set_nodemask(new, &nodes, scratch);
+			task_unlock(current);
+		} else
+			ret = -ENOMEM;
+		NODEMASK_SCRATCH_FREE(scratch);
+		if (ret) {
 			err = 1;
-		else if (no_context) {
+			mpol_put(new);
+		} else if (no_context) {
 			/* save for contextualization */
 			new->w.user_nodemask = nodes;
 		}
-- 
GitLab


From 521594442cc62d1c2af8436a05ab5918b7730b19 Mon Sep 17 00:00:00 2001
From: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Date: Thu, 6 Aug 2009 15:07:34 -0700
Subject: [PATCH 0640/1153] viafb: fix rmmod bug

This fixes a bug caused by changing pointers (viafb_mode, viafb_mode1)
assigned by module_param.  It reduces driver complexity by not needlessly
changing these vars as they are only read once and removing now
superfluous code.

On unpatched kernels loading viafb with viafb_mode or viafb_mode1 option
used and afterwards unloading it results in:

kernel BUG at mm/slub.c:2926!
invalid opcode: 0000 [#1] PREEMPT
last sysfs file: /sys/devices/virtual/block/loop0/removable
Modules linked in: snd_hda_codec_realtek snd_hda_intel snd_hda_codec
snd_hwdep snd_pcm rtl8187 snd_timer eeprom_93cx6 mmc_block snd soundcore
via_sdmmc fb snd_page_alloc i2c_algo_bit i2c_viapro ehci_hcd uhci_hcd
cfbcopyarea mmc_core cfbimgblt cfbfillrect video output [last unloaded:
viafb]

  Pid: 3355, comm: rmmod Not tainted (2.6.31-rc1 #0)
  EIP: 0060:[<c106a759>] EFLAGS: 00010246 CPU: 0
  EIP is at kfree+0x80/0xda
  EAX: c17c2da0 EBX: dc7edbdc ECX: 0000010f EDX: 00000000
  ESI: c102c700 EDI: dc7ed8fa EBP: d703ff2c ESP: d703ff20
   DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
  Process rmmod (pid: 3355, ti=d703e000 task=db1412c0 task.ti=d703e000)
  Stack:
   dc7edbdc 00000014 00000016 d703ff40 c102c700 dc7f45d4 dc7f45d4 00000880
   d703ff4c c103e571 00000000 d703ffac c103e751 66616976 da140062 db89ba80
   00000328 d702edf8 db89ba80 d703ff9c c105d0f0 00000200 da14f898 00000014
  Call Trace:
   [<c102c700>] ? destroy_params+0x1e/0x2b
   [<c103e571>] ? free_module+0xa2/0xd7
   [<c103e751>] ? sys_delete_module+0x1ab/0x1da
   [<c105d0f0>] ? do_munmap+0x20a/0x225
   [<c10029b4>] ? sysenter_do_call+0x12/0x26
  Code: 10 76 7a 8d 87 00 00 00 40 c1 e8 0c c1 e0 05 03 05 1c 87 41 c1 66 83 38 00 79 03 8b 40 0c 8b 10 84 d2 78 12 66 f7 c2 00 c0 75 04 <0f> 0b eb fe e8 6f 5a fe ff eb 47 8b 55 04 8b 58 0c 9c 5e fa 3b
  EIP: [<c106a759>] kfree+0x80/0xda SS:ESP 0068:d703ff20

This is caused by the current code changing the pointers assigned by
module_param.  During unload it tries to free the memory the pointers
point at which is now part of an internal structure.

The patch simply avoids changing the pointers.  This is okay as they are
read only once during the initialization process.

Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/video/via/hw.c       |   4 +-
 drivers/video/via/lcd.c      |  15 ++----
 drivers/video/via/viafbdev.c | 101 ++++++++++++++++-------------------
 drivers/video/via/viafbdev.h |   3 +-
 4 files changed, 53 insertions(+), 70 deletions(-)

diff --git a/drivers/video/via/hw.c b/drivers/video/via/hw.c
index fcd53ceb88f..c8960003f47 100644
--- a/drivers/video/via/hw.c
+++ b/drivers/video/via/hw.c
@@ -2407,14 +2407,14 @@ int viafb_setmode(int vmode_index, int hor_res, int ver_res, int video_bpp,
 			viafb_dvi_set_mode(viafb_get_mode_index
 				     (viaparinfo->tmds_setting_info->h_active,
 				      viaparinfo->tmds_setting_info->
-				      v_active, 1),
+				      v_active),
 				     video_bpp1, viaparinfo->
 				     tmds_setting_info->iga_path);
 		} else {
 			viafb_dvi_set_mode(viafb_get_mode_index
 				     (viaparinfo->tmds_setting_info->h_active,
 				      viaparinfo->
-				      tmds_setting_info->v_active, 0),
+				      tmds_setting_info->v_active),
 				     video_bpp, viaparinfo->
 				     tmds_setting_info->iga_path);
 		}
diff --git a/drivers/video/via/lcd.c b/drivers/video/via/lcd.c
index 6c7290a6a44..78c6b338794 100644
--- a/drivers/video/via/lcd.c
+++ b/drivers/video/via/lcd.c
@@ -580,10 +580,7 @@ static void load_lcd_k400_patch_tbl(int set_hres, int set_vres,
 	int reg_num = 0;
 	struct io_reg *lcd_patch_reg = NULL;
 
-	if (viaparinfo->lvds_setting_info->iga_path == IGA2)
-		vmode_index = viafb_get_mode_index(set_hres, set_vres, 1);
-	else
-		vmode_index = viafb_get_mode_index(set_hres, set_vres, 0);
+	vmode_index = viafb_get_mode_index(set_hres, set_vres);
 	switch (panel_id) {
 		/* LCD 800x600 */
 	case LCD_PANEL_ID1_800X600:
@@ -761,10 +758,7 @@ static void load_lcd_p880_patch_tbl(int set_hres, int set_vres,
 	int reg_num = 0;
 	struct io_reg *lcd_patch_reg = NULL;
 
-	if (viaparinfo->lvds_setting_info->iga_path == IGA2)
-		vmode_index = viafb_get_mode_index(set_hres, set_vres, 1);
-	else
-		vmode_index = viafb_get_mode_index(set_hres, set_vres, 0);
+	vmode_index = viafb_get_mode_index(set_hres, set_vres);
 
 	switch (panel_id) {
 	case LCD_PANEL_ID5_1400X1050:
@@ -832,10 +826,7 @@ static void load_lcd_patch_regs(int set_hres, int set_vres,
 {
 	int vmode_index;
 
-	if (viaparinfo->lvds_setting_info->iga_path == IGA2)
-		vmode_index = viafb_get_mode_index(set_hres, set_vres, 1);
-	else
-		vmode_index = viafb_get_mode_index(set_hres, set_vres, 0);
+	vmode_index = viafb_get_mode_index(set_hres, set_vres);
 
 	viafb_unlock_crt();
 
diff --git a/drivers/video/via/viafbdev.c b/drivers/video/via/viafbdev.c
index a0fec298216..72833f3334b 100644
--- a/drivers/video/via/viafbdev.c
+++ b/drivers/video/via/viafbdev.c
@@ -32,7 +32,6 @@ static u32 pseudo_pal[17];
 /* video mode */
 static char *viafb_mode = "640x480";
 static char *viafb_mode1 = "640x480";
-static int viafb_resMode = VIA_RES_640X480;
 
 /* Added for specifying active devices.*/
 char *viafb_active_dev = "";
@@ -56,47 +55,47 @@ static void viafb_get_video_device(u32 *video_dev_info);
 
 /* Mode information */
 static const struct viafb_modeinfo viafb_modentry[] = {
-	{480, 640, VIA_RES_480X640, "480x640"},
-	{640, 480, VIA_RES_640X480, "640x480"},
-	{800, 480, VIA_RES_800X480, "800x480"},
-	{800, 600, VIA_RES_800X600, "800x600"},
-	{1024, 768, VIA_RES_1024X768, "1024x768"},
-	{1152, 864, VIA_RES_1152X864, "1152x864"},
-	{1280, 1024, VIA_RES_1280X1024, "1280x1024"},
-	{1600, 1200, VIA_RES_1600X1200, "1600x1200"},
-	{1440, 1050, VIA_RES_1440X1050, "1440x1050"},
-	{1280, 768, VIA_RES_1280X768, "1280x768"},
-	{1280, 800, VIA_RES_1280X800, "1280x800"},
-	{1280, 960, VIA_RES_1280X960, "1280x960"},
-	{1920, 1440, VIA_RES_1920X1440, "1920x1440"},
-	{848, 480, VIA_RES_848X480, "848x480"},
-	{1400, 1050, VIA_RES_1400X1050, "1400x1050"},
-	{720, 480, VIA_RES_720X480, "720x480"},
-	{720, 576, VIA_RES_720X576, "720x576"},
-	{1024, 512, VIA_RES_1024X512, "1024x512"},
-	{1024, 576, VIA_RES_1024X576, "1024x576"},
-	{1024, 600, VIA_RES_1024X600, "1024x600"},
-	{1280, 720, VIA_RES_1280X720, "1280x720"},
-	{1920, 1080, VIA_RES_1920X1080, "1920x1080"},
-	{1366, 768, VIA_RES_1368X768, "1368x768"},
-	{1680, 1050, VIA_RES_1680X1050, "1680x1050"},
-	{960, 600, VIA_RES_960X600, "960x600"},
-	{1000, 600, VIA_RES_1000X600, "1000x600"},
-	{1024, 576, VIA_RES_1024X576, "1024x576"},
-	{1024, 600, VIA_RES_1024X600, "1024x600"},
-	{1088, 612, VIA_RES_1088X612, "1088x612"},
-	{1152, 720, VIA_RES_1152X720, "1152x720"},
-	{1200, 720, VIA_RES_1200X720, "1200x720"},
-	{1280, 600, VIA_RES_1280X600, "1280x600"},
-	{1360, 768, VIA_RES_1360X768, "1360x768"},
-	{1440, 900, VIA_RES_1440X900, "1440x900"},
-	{1600, 900, VIA_RES_1600X900, "1600x900"},
-	{1600, 1024, VIA_RES_1600X1024, "1600x1024"},
-	{1792, 1344, VIA_RES_1792X1344, "1792x1344"},
-	{1856, 1392, VIA_RES_1856X1392, "1856x1392"},
-	{1920, 1200, VIA_RES_1920X1200, "1920x1200"},
-	{2048, 1536, VIA_RES_2048X1536, "2048x1536"},
-	{0, 0, VIA_RES_INVALID, "640x480"}
+	{480, 640, VIA_RES_480X640},
+	{640, 480, VIA_RES_640X480},
+	{800, 480, VIA_RES_800X480},
+	{800, 600, VIA_RES_800X600},
+	{1024, 768, VIA_RES_1024X768},
+	{1152, 864, VIA_RES_1152X864},
+	{1280, 1024, VIA_RES_1280X1024},
+	{1600, 1200, VIA_RES_1600X1200},
+	{1440, 1050, VIA_RES_1440X1050},
+	{1280, 768, VIA_RES_1280X768,},
+	{1280, 800, VIA_RES_1280X800},
+	{1280, 960, VIA_RES_1280X960},
+	{1920, 1440, VIA_RES_1920X1440},
+	{848, 480, VIA_RES_848X480},
+	{1400, 1050, VIA_RES_1400X1050},
+	{720, 480, VIA_RES_720X480},
+	{720, 576, VIA_RES_720X576},
+	{1024, 512, VIA_RES_1024X512},
+	{1024, 576, VIA_RES_1024X576},
+	{1024, 600, VIA_RES_1024X600},
+	{1280, 720, VIA_RES_1280X720},
+	{1920, 1080, VIA_RES_1920X1080},
+	{1366, 768, VIA_RES_1368X768},
+	{1680, 1050, VIA_RES_1680X1050},
+	{960, 600, VIA_RES_960X600},
+	{1000, 600, VIA_RES_1000X600},
+	{1024, 576, VIA_RES_1024X576},
+	{1024, 600, VIA_RES_1024X600},
+	{1088, 612, VIA_RES_1088X612},
+	{1152, 720, VIA_RES_1152X720},
+	{1200, 720, VIA_RES_1200X720},
+	{1280, 600, VIA_RES_1280X600},
+	{1360, 768, VIA_RES_1360X768},
+	{1440, 900, VIA_RES_1440X900},
+	{1600, 900, VIA_RES_1600X900},
+	{1600, 1024, VIA_RES_1600X1024},
+	{1792, 1344, VIA_RES_1792X1344},
+	{1856, 1392, VIA_RES_1856X1392},
+	{1920, 1200, VIA_RES_1920X1200},
+	{2048, 1536, VIA_RES_2048X1536},
+	{0, 0, VIA_RES_INVALID}
 };
 
 static struct fb_ops viafb_ops;
@@ -177,7 +176,7 @@ static int viafb_check_var(struct fb_var_screeninfo *var,
 	if (var->vmode & FB_VMODE_INTERLACED || var->vmode & FB_VMODE_DOUBLE)
 		return -EINVAL;
 
-	vmode_index = viafb_get_mode_index(var->xres, var->yres, 0);
+	vmode_index = viafb_get_mode_index(var->xres, var->yres);
 	if (vmode_index == VIA_RES_INVALID) {
 		DEBUG_MSG(KERN_INFO
 			  "viafb: Mode %dx%dx%d not supported!!\n",
@@ -233,14 +232,14 @@ static int viafb_set_par(struct fb_info *info)
 	viafb_update_device_setting(info->var.xres, info->var.yres,
 			      info->var.bits_per_pixel, viafb_refresh, 0);
 
-	vmode_index = viafb_get_mode_index(info->var.xres, info->var.yres, 0);
+	vmode_index = viafb_get_mode_index(info->var.xres, info->var.yres);
 
 	if (viafb_SAMM_ON == 1) {
 		DEBUG_MSG(KERN_INFO
 		"viafb_second_xres = %d, viafb_second_yres = %d, bpp = %d\n",
 			  viafb_second_xres, viafb_second_yres, viafb_bpp1);
 		vmode_index1 = viafb_get_mode_index(viafb_second_xres,
-			viafb_second_yres, 1);
+			viafb_second_yres);
 		DEBUG_MSG(KERN_INFO "->viafb_SAMM_ON: index=%d\n",
 			vmode_index1);
 
@@ -1262,7 +1261,7 @@ static int viafb_sync(struct fb_info *info)
 	return 0;
 }
 
-int viafb_get_mode_index(int hres, int vres, int flag)
+int viafb_get_mode_index(int hres, int vres)
 {
 	u32 i;
 	DEBUG_MSG(KERN_INFO "viafb_get_mode_index!\n");
@@ -1272,13 +1271,7 @@ int viafb_get_mode_index(int hres, int vres, int flag)
 			viafb_modentry[i].yres == vres)
 			break;
 
-	viafb_resMode = viafb_modentry[i].mode_index;
-	if (flag)
-		viafb_mode1 = viafb_modentry[i].mode_res;
-	else
-		viafb_mode = viafb_modentry[i].mode_res;
-
-	return viafb_resMode;
+	return viafb_modentry[i].mode_index;
 }
 
 static void check_available_device_to_enable(int device_id)
@@ -2199,7 +2192,7 @@ static int __devinit via_pci_probe(void)
 	strict_strtoul(tmpc, 0, &default_xres);
 	strict_strtoul(tmpm, 0, &default_yres);
 
-	vmode_index = viafb_get_mode_index(default_xres, default_yres, 0);
+	vmode_index = viafb_get_mode_index(default_xres, default_yres);
 	DEBUG_MSG(KERN_INFO "0->index=%d\n", vmode_index);
 
 	if (viafb_SAMM_ON == 1) {
diff --git a/drivers/video/via/viafbdev.h b/drivers/video/via/viafbdev.h
index a4158e87287..227b000feb3 100644
--- a/drivers/video/via/viafbdev.h
+++ b/drivers/video/via/viafbdev.h
@@ -81,7 +81,6 @@ struct viafb_modeinfo {
 	u32 xres;
 	u32 yres;
 	int mode_index;
-	char *mode_res;
 };
 extern unsigned int viafb_second_virtual_yres;
 extern unsigned int viafb_second_virtual_xres;
@@ -102,7 +101,7 @@ extern int strict_strtoul(const char *cp, unsigned int base,
 void viafb_memory_pitch_patch(struct fb_info *info);
 void viafb_fill_var_timing_info(struct fb_var_screeninfo *var, int refresh,
 			  int mode_index);
-int viafb_get_mode_index(int hres, int vres, int flag);
+int viafb_get_mode_index(int hres, int vres);
 u8 viafb_gpio_i2c_read_lvds(struct lvds_setting_information
 	*plvds_setting_info, struct lvds_chip_information
 	*plvds_chip_info, u8 index);
-- 
GitLab


From 0035fe00f77d2b0a1a2d001f7442136d1ec5aefa Mon Sep 17 00:00:00 2001
From: Johannes Weiner <hannes@cmpxchg.org>
Date: Thu, 6 Aug 2009 15:07:36 -0700
Subject: [PATCH 0641/1153] fbcon: don't use vc_resize() on initialization

Catalin and kmemleak spotted a leak of a VC screen buffer in
vc_allocate() due to the following chain of events:

	vc_allocate()
	  visual_init(init=1)
	    vc->vc_sw->con_init(init=1)
              fbcon_init()
	        vc_resize()
	          vc->screen_buf = kmalloc()
	  vc->screen_buf = kmalloc()

The common way for the VC drivers is to set the screen dimension
parameters manually in the init case and only call vc_resize() for
!init - which allocates a screen buffer according to the new
dimensions.

fbcon instead would do vc_resize() unconditionally and afterwards set
the dimensions manually (again) for !init - i.e. completely upside
down.  The vc_resize() allocated buffer would then get lost by
vc_allocate() allocating a fresh one.

Use vc_resize() only for actual resizing to close the leak.

Set the dimensions manually only in initialization mode to remove the
redundant setting in resize mode.

The kmemleak trace from Catalin:

unreferenced object 0xde158000 (size 12288):
  comm "Xorg", pid 1439, jiffies 4294961016
  hex dump (first 32 bytes):
    20 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00   . . . . . . . .
    20 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00   . . . . . . . .
  backtrace:
    [<c006f74b>] __save_stack_trace+0x17/0x1c
    [<c006f81d>] create_object+0xcd/0x188
    [<c01f5457>] kmemleak_alloc+0x1b/0x3c
    [<c006e303>] __kmalloc+0xdb/0xe8
    [<c012cc4b>] vc_do_resize+0x73/0x1e0
    [<c012cdf1>] vc_resize+0x15/0x18
    [<c011afc1>] fbcon_init+0x1f9/0x2b8
    [<c0129e87>] visual_init+0x9f/0xdc
    [<c012aff3>] vc_allocate+0x7f/0xfc
    [<c012b087>] con_open+0x17/0x80
    [<c0120e43>] tty_open+0x1f7/0x2e4
    [<c0072fa1>] chrdev_open+0x101/0x118
    [<c006ffad>] __dentry_open+0x105/0x1cc
    [<c00700fd>] nameidata_to_filp+0x2d/0x38
    [<c00788cd>] do_filp_open+0x2c1/0x54c
    [<c006fdff>] do_sys_open+0x3b/0xb4

Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/video/console/fbcon.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/video/console/fbcon.c b/drivers/video/console/fbcon.c
index 471a9a60376..3a44695b9c0 100644
--- a/drivers/video/console/fbcon.c
+++ b/drivers/video/console/fbcon.c
@@ -1082,7 +1082,6 @@ static void fbcon_init(struct vc_data *vc, int init)
 	new_rows = FBCON_SWAP(ops->rotate, info->var.yres, info->var.xres);
 	new_cols /= vc->vc_font.width;
 	new_rows /= vc->vc_font.height;
-	vc_resize(vc, new_cols, new_rows);
 
 	/*
 	 * We must always set the mode. The mode of the previous console
@@ -1111,10 +1110,11 @@ static void fbcon_init(struct vc_data *vc, int init)
 	 *  vc_{cols,rows}, but we must not set those if we are only
 	 *  resizing the console.
 	 */
-	if (!init) {
+	if (init) {
 		vc->vc_cols = new_cols;
 		vc->vc_rows = new_rows;
-	}
+	} else
+		vc_resize(vc, new_cols, new_rows);
 
 	if (logo)
 		fbcon_prepare_logo(vc, info, cols, rows, new_cols, new_rows);
-- 
GitLab


From 69130c7cf96ea853dc5be599dd6a4b98907d39cc Mon Sep 17 00:00:00 2001
From: Eric Sandeen <sandeen@redhat.com>
Date: Thu, 6 Aug 2009 15:07:37 -0700
Subject: [PATCH 0642/1153] compat_ioctl: hook up compat handler for FIEMAP
 ioctl

The FIEMAP_IOC_FIEMAP mapping ioctl was missing a 32-bit compat handler,
which means that 32-bit suerspace on 64-bit kernels cannot use this ioctl
command.

The structure is nicely aligned, padded, and sized, so it is just this
simple.

Tested w/ 32-bit ioctl tester (from Josef) on a 64-bit kernel on ext4.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Josef Bacik <josef@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/compat_ioctl.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/fs/compat_ioctl.c b/fs/compat_ioctl.c
index f28f070a60f..f91fd51b32e 100644
--- a/fs/compat_ioctl.c
+++ b/fs/compat_ioctl.c
@@ -1905,6 +1905,7 @@ COMPATIBLE_IOCTL(FIONCLEX)
 COMPATIBLE_IOCTL(FIOASYNC)
 COMPATIBLE_IOCTL(FIONBIO)
 COMPATIBLE_IOCTL(FIONREAD)  /* This is also TIOCINQ */
+COMPATIBLE_IOCTL(FS_IOC_FIEMAP)
 /* 0x00 */
 COMPATIBLE_IOCTL(FIBMAP)
 COMPATIBLE_IOCTL(FIGETBSZ)
-- 
GitLab


From 2d8dd38a5aa0cc2490bbad9b75e77fa154e1d145 Mon Sep 17 00:00:00 2001
From: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Date: Thu, 6 Aug 2009 15:07:39 -0700
Subject: [PATCH 0643/1153] vfs: mnt_want_write_file(): fix special file
 handling

I suspect that mnt_want_write_file() may have wrong assumption.  I think
mnt_want_write_file() is assuming it increments ->mnt_writers if
(file->f_mode & FMODE_WRITE).  But, if it's special_file(), it is false?

Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/namespace.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/fs/namespace.c b/fs/namespace.c
index 277c28a63ea..7230787d18b 100644
--- a/fs/namespace.c
+++ b/fs/namespace.c
@@ -316,7 +316,8 @@ EXPORT_SYMBOL_GPL(mnt_clone_write);
  */
 int mnt_want_write_file(struct file *file)
 {
-	if (!(file->f_mode & FMODE_WRITE))
+	struct inode *inode = file->f_dentry->d_inode;
+	if (!(file->f_mode & FMODE_WRITE) || special_file(inode->i_mode))
 		return mnt_want_write(file->f_path.mnt);
 	else
 		return mnt_clone_write(file->f_path.mnt);
-- 
GitLab


From 20de03dae54e10271ffd308654dfb4a117f4789d Mon Sep 17 00:00:00 2001
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Date: Thu, 6 Aug 2009 15:07:40 -0700
Subject: [PATCH 0644/1153] i.MX31: fix framebuffer locking regressions

Recent framebuffer locking patches first made affected systems unbootable,
then the dead-lock has been fixed but as of 2.6.31-rc4 the framebuffer on
mx3 machines doesn't work. Fix this.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/video/mx3fb.c | 86 ++++++++++++++++++++++++++++---------------
 1 file changed, 56 insertions(+), 30 deletions(-)

diff --git a/drivers/video/mx3fb.c b/drivers/video/mx3fb.c
index f8778cde218..054ef29be47 100644
--- a/drivers/video/mx3fb.c
+++ b/drivers/video/mx3fb.c
@@ -669,7 +669,8 @@ static uint32_t bpp_to_pixfmt(int bpp)
 }
 
 static int mx3fb_blank(int blank, struct fb_info *fbi);
-static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len);
+static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len,
+				  bool lock);
 static int mx3fb_unmap_video_memory(struct fb_info *fbi);
 
 /**
@@ -711,12 +712,7 @@ static void mx3fb_dma_done(void *arg)
 	complete(&mx3_fbi->flip_cmpl);
 }
 
-/**
- * mx3fb_set_par() - set framebuffer parameters and change the operating mode.
- * @fbi:	framebuffer information pointer.
- * @return:	0 on success or negative error code on failure.
- */
-static int mx3fb_set_par(struct fb_info *fbi)
+static int __set_par(struct fb_info *fbi, bool lock)
 {
 	u32 mem_len;
 	struct ipu_di_signal_cfg sig_cfg;
@@ -727,10 +723,6 @@ static int mx3fb_set_par(struct fb_info *fbi)
 	struct idmac_video_param *video = &ichan->params.video;
 	struct scatterlist *sg = mx3_fbi->sg;
 
-	dev_dbg(mx3fb->dev, "%s [%c]\n", __func__, list_empty(&ichan->queue) ? '-' : '+');
-
-	mutex_lock(&mx3_fbi->mutex);
-
 	/* Total cleanup */
 	if (mx3_fbi->txd)
 		sdc_disable_channel(mx3_fbi);
@@ -742,10 +734,8 @@ static int mx3fb_set_par(struct fb_info *fbi)
 		if (fbi->fix.smem_start)
 			mx3fb_unmap_video_memory(fbi);
 
-		if (mx3fb_map_video_memory(fbi, mem_len) < 0) {
-			mutex_unlock(&mx3_fbi->mutex);
+		if (mx3fb_map_video_memory(fbi, mem_len, lock) < 0)
 			return -ENOMEM;
-		}
 	}
 
 	sg_init_table(&sg[0], 1);
@@ -791,7 +781,6 @@ static int mx3fb_set_par(struct fb_info *fbi)
 				   fbi->var.vsync_len,
 				   fbi->var.lower_margin +
 				   fbi->var.vsync_len, sig_cfg) != 0) {
-			mutex_unlock(&mx3_fbi->mutex);
 			dev_err(fbi->device,
 				"mx3fb: Error initializing panel.\n");
 			return -EINVAL;
@@ -810,9 +799,30 @@ static int mx3fb_set_par(struct fb_info *fbi)
 	if (mx3_fbi->blank == FB_BLANK_UNBLANK)
 		sdc_enable_channel(mx3_fbi);
 
+	return 0;
+}
+
+/**
+ * mx3fb_set_par() - set framebuffer parameters and change the operating mode.
+ * @fbi:	framebuffer information pointer.
+ * @return:	0 on success or negative error code on failure.
+ */
+static int mx3fb_set_par(struct fb_info *fbi)
+{
+	struct mx3fb_info *mx3_fbi = fbi->par;
+	struct mx3fb_data *mx3fb = mx3_fbi->mx3fb;
+	struct idmac_channel *ichan = mx3_fbi->idmac_channel;
+	int ret;
+
+	dev_dbg(mx3fb->dev, "%s [%c]\n", __func__, list_empty(&ichan->queue) ? '-' : '+');
+
+	mutex_lock(&mx3_fbi->mutex);
+
+	ret = __set_par(fbi, true);
+
 	mutex_unlock(&mx3_fbi->mutex);
 
-	return 0;
+	return ret;
 }
 
 /**
@@ -966,21 +976,11 @@ static int mx3fb_setcolreg(unsigned int regno, unsigned int red,
 	return ret;
 }
 
-/**
- * mx3fb_blank() - blank the display.
- */
-static int mx3fb_blank(int blank, struct fb_info *fbi)
+static void __blank(int blank, struct fb_info *fbi)
 {
 	struct mx3fb_info *mx3_fbi = fbi->par;
 	struct mx3fb_data *mx3fb = mx3_fbi->mx3fb;
 
-	dev_dbg(fbi->device, "%s, blank = %d, base %p, len %u\n", __func__,
-		blank, fbi->screen_base, fbi->fix.smem_len);
-
-	if (mx3_fbi->blank == blank)
-		return 0;
-
-	mutex_lock(&mx3_fbi->mutex);
 	mx3_fbi->blank = blank;
 
 	switch (blank) {
@@ -999,6 +999,23 @@ static int mx3fb_blank(int blank, struct fb_info *fbi)
 		sdc_set_brightness(mx3fb, mx3fb->backlight_level);
 		break;
 	}
+}
+
+/**
+ * mx3fb_blank() - blank the display.
+ */
+static int mx3fb_blank(int blank, struct fb_info *fbi)
+{
+	struct mx3fb_info *mx3_fbi = fbi->par;
+
+	dev_dbg(fbi->device, "%s, blank = %d, base %p, len %u\n", __func__,
+		blank, fbi->screen_base, fbi->fix.smem_len);
+
+	if (mx3_fbi->blank == blank)
+		return 0;
+
+	mutex_lock(&mx3_fbi->mutex);
+	__blank(blank, fbi);
 	mutex_unlock(&mx3_fbi->mutex);
 
 	return 0;
@@ -1198,6 +1215,7 @@ static int mx3fb_resume(struct platform_device *pdev)
  * mx3fb_map_video_memory() - allocates the DRAM memory for the frame buffer.
  * @fbi:	framebuffer information pointer
  * @mem_len:	length of mapped memory
+ * @lock:	do not lock during initialisation
  * @return:	Error code indicating success or failure
  *
  * This buffer is remapped into a non-cached, non-buffered, memory region to
@@ -1205,7 +1223,8 @@ static int mx3fb_resume(struct platform_device *pdev)
  * area is remapped, all virtual memory access to the video memory should occur
  * at the new region.
  */
-static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len)
+static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len,
+				  bool lock)
 {
 	int retval = 0;
 	dma_addr_t addr;
@@ -1221,10 +1240,12 @@ static int mx3fb_map_video_memory(struct fb_info *fbi, unsigned int mem_len)
 		goto err0;
 	}
 
-	mutex_lock(&fbi->mm_lock);
+	if (lock)
+		mutex_lock(&fbi->mm_lock);
 	fbi->fix.smem_start = addr;
 	fbi->fix.smem_len = mem_len;
-	mutex_unlock(&fbi->mm_lock);
+	if (lock)
+		mutex_unlock(&fbi->mm_lock);
 
 	dev_dbg(fbi->device, "allocated fb @ p=0x%08x, v=0x%p, size=%d.\n",
 		(uint32_t) fbi->fix.smem_start, fbi->screen_base, fbi->fix.smem_len);
@@ -1365,6 +1386,11 @@ static int init_fb_chan(struct mx3fb_data *mx3fb, struct idmac_channel *ichan)
 	init_completion(&mx3fbi->flip_cmpl);
 	disable_irq(ichan->eof_irq);
 	dev_dbg(mx3fb->dev, "disabling irq %d\n", ichan->eof_irq);
+	ret = __set_par(fbi, false);
+	if (ret < 0)
+		goto esetpar;
+
+	__blank(FB_BLANK_UNBLANK, fbi);
 
 	dev_info(dev, "registered, using mode %s\n", fb_mode);
 
-- 
GitLab


From 2198a64a7487aba036f71998ade8a6528070d32c Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Thu, 6 Aug 2009 15:07:41 -0700
Subject: [PATCH 0645/1153] drivers/mmc: correct error-handling code

sdhci_alloc_host returns an ERR_PTR value in an error case instead of NULL.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@match exists@
expression x, E;
statement S1, S2;
@@

x = sdhci_alloc_host(...)
... when != x = E
(
*  if (x == NULL || ...) S1 else S2
|
*  if (x == NULL && ...) S1 else S2
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/mmc/host/sdhci-of.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-of.c b/drivers/mmc/host/sdhci-of.c
index 908844327db..1e8aa590bb3 100644
--- a/drivers/mmc/host/sdhci-of.c
+++ b/drivers/mmc/host/sdhci-of.c
@@ -234,7 +234,7 @@ static int __devinit sdhci_of_probe(struct of_device *ofdev,
 		return -ENODEV;
 
 	host = sdhci_alloc_host(&ofdev->dev, sizeof(*of_host));
-	if (!host)
+	if (IS_ERR(host))
 		return -ENOMEM;
 
 	of_host = sdhci_priv(host);
-- 
GitLab


From 9c8a8228d0827e0d91d28527209988f672f97d28 Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Thu, 6 Aug 2009 15:09:28 -0700
Subject: [PATCH 0646/1153] execve: must clear current->clear_child_tid

While looking at Jens Rosenboom bug report
(http://lkml.org/lkml/2009/7/27/35) about strange sys_futex call done from
a dying "ps" program, we found following problem.

clone() syscall has special support for TID of created threads.  This
support includes two features.

One (CLONE_CHILD_SETTID) is to set an integer into user memory with the
TID value.

One (CLONE_CHILD_CLEARTID) is to clear this same integer once the created
thread dies.

The integer location is a user provided pointer, provided at clone()
time.

kernel keeps this pointer value into current->clear_child_tid.

At execve() time, we should make sure kernel doesnt keep this user
provided pointer, as full user memory is replaced by a new one.

As glibc fork() actually uses clone() syscall with CLONE_CHILD_SETTID and
CLONE_CHILD_CLEARTID set, chances are high that we might corrupt user
memory in forked processes.

Following sequence could happen:

1) bash (or any program) starts a new process, by a fork() call that
   glibc maps to a clone( ...  CLONE_CHILD_SETTID | CLONE_CHILD_CLEARTID
   ...) syscall

2) When new process starts, its current->clear_child_tid is set to a
   location that has a meaning only in bash (or initial program) context
   (&THREAD_SELF->tid)

3) This new process does the execve() syscall to start a new program.
   current->clear_child_tid is left unchanged (a non NULL value)

4) If this new program creates some threads, and initial thread exits,
   kernel will attempt to clear the integer pointed by
   current->clear_child_tid from mm_release() :

        if (tsk->clear_child_tid
            && !(tsk->flags & PF_SIGNALED)
            && atomic_read(&mm->mm_users) > 1) {
                u32 __user * tidptr = tsk->clear_child_tid;
                tsk->clear_child_tid = NULL;

                /*
                 * We don't check the error code - if userspace has
                 * not set up a proper pointer then tough luck.
                 */
<< here >>      put_user(0, tidptr);
                sys_futex(tidptr, FUTEX_WAKE, 1, NULL, NULL, 0);
        }

5) OR : if new program is not multi-threaded, but spied by /proc/pid
   users (ps command for example), mm_users > 1, and the exiting program
   could corrupt 4 bytes in a persistent memory area (shm or memory mapped
   file)

If current->clear_child_tid points to a writeable portion of memory of the
new program, kernel happily and silently corrupts 4 bytes of memory, with
unexpected effects.

Fix is straightforward and should not break any sane program.

Reported-by: Jens Rosenboom <jens@mcbone.net>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sonny Rao <sonnyrao@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/fork.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/kernel/fork.c b/kernel/fork.c
index 466531eb92c..021e1138556 100644
--- a/kernel/fork.c
+++ b/kernel/fork.c
@@ -568,18 +568,18 @@ void mm_release(struct task_struct *tsk, struct mm_struct *mm)
 	 * the value intact in a core dump, and to save the unnecessary
 	 * trouble otherwise.  Userland only wants this done for a sys_exit.
 	 */
-	if (tsk->clear_child_tid
-	    && !(tsk->flags & PF_SIGNALED)
-	    && atomic_read(&mm->mm_users) > 1) {
-		u32 __user * tidptr = tsk->clear_child_tid;
+	if (tsk->clear_child_tid) {
+		if (!(tsk->flags & PF_SIGNALED) &&
+		    atomic_read(&mm->mm_users) > 1) {
+			/*
+			 * We don't check the error code - if userspace has
+			 * not set up a proper pointer then tough luck.
+			 */
+			put_user(0, tsk->clear_child_tid);
+			sys_futex(tsk->clear_child_tid, FUTEX_WAKE,
+					1, NULL, NULL, 0);
+		}
 		tsk->clear_child_tid = NULL;
-
-		/*
-		 * We don't check the error code - if userspace has
-		 * not set up a proper pointer then tough luck.
-		 */
-		put_user(0, tidptr);
-		sys_futex(tidptr, FUTEX_WAKE, 1, NULL, NULL, 0);
 	}
 }
 
-- 
GitLab


From daeb6b6fbe27049f465c48a7d0ee5555c3b84064 Mon Sep 17 00:00:00 2001
From: Phillip Lougher <phillip@lougher.demon.co.uk>
Date: Thu, 6 Aug 2009 15:09:30 -0700
Subject: [PATCH 0647/1153] bzip2/lzma/gzip: fix comments describing
 decompressor API

Fix and improve comments in decompress/generic.h that describe the
decompressor API.  Also remove an unused definition, and rename INBUF_LEN
in lib/decompress_inflate.c to conform to bzip2/lzma naming.

Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/decompress/generic.h | 32 ++++++++++++++++++------------
 lib/decompress_inflate.c           |  8 ++++----
 2 files changed, 23 insertions(+), 17 deletions(-)

diff --git a/include/linux/decompress/generic.h b/include/linux/decompress/generic.h
index 6dfb856327b..0c7111a55a1 100644
--- a/include/linux/decompress/generic.h
+++ b/include/linux/decompress/generic.h
@@ -1,31 +1,37 @@
 #ifndef DECOMPRESS_GENERIC_H
 #define DECOMPRESS_GENERIC_H
 
-/* Minimal chunksize to be read.
- *Bzip2 prefers at least 4096
- *Lzma prefers 0x10000 */
-#define COMPR_IOBUF_SIZE	4096
-
 typedef int (*decompress_fn) (unsigned char *inbuf, int len,
 			      int(*fill)(void*, unsigned int),
-			      int(*writebb)(void*, unsigned int),
-			      unsigned char *output,
+			      int(*flush)(void*, unsigned int),
+			      unsigned char *outbuf,
 			      int *posp,
 			      void(*error)(char *x));
 
 /* inbuf   - input buffer
  *len     - len of pre-read data in inbuf
- *fill    - function to fill inbuf if empty
- *writebb - function to write out outbug
+ *fill    - function to fill inbuf when empty
+ *flush   - function to write out outbuf
+ *outbuf  - output buffer
  *posp    - if non-null, input position (number of bytes read) will be
  *	  returned here
  *
- *If len != 0, the inbuf is initialized (with as much data), and fill
- *should not be called
- *If len = 0, the inbuf is allocated, but empty. Its size is IOBUF_SIZE
- *fill should be called (repeatedly...) to read data, at most IOBUF_SIZE
+ *If len != 0, inbuf should contain all the necessary input data, and fill
+ *should be NULL
+ *If len = 0, inbuf can be NULL, in which case the decompressor will allocate
+ *the input buffer.  If inbuf != NULL it must be at least XXX_IOBUF_SIZE bytes.
+ *fill will be called (repeatedly...) to read data, at most XXX_IOBUF_SIZE
+ *bytes should be read per call.  Replace XXX with the appropriate decompressor
+ *name, i.e. LZMA_IOBUF_SIZE.
+ *
+ *If flush = NULL, outbuf must be large enough to buffer all the expected
+ *output.  If flush != NULL, the output buffer will be allocated by the
+ *decompressor (outbuf = NULL), and the flush function will be called to
+ *flush the output buffer at the appropriate time (decompressor and stream
+ *dependent).
  */
 
+
 /* Utility routine to detect the decompression method */
 decompress_fn decompress_method(const unsigned char *inbuf, int len,
 				const char **name);
diff --git a/lib/decompress_inflate.c b/lib/decompress_inflate.c
index e36b296fc9f..bfe605ac534 100644
--- a/lib/decompress_inflate.c
+++ b/lib/decompress_inflate.c
@@ -25,7 +25,7 @@
 #include <linux/decompress/mm.h>
 #include <linux/slab.h>
 
-#define INBUF_LEN (16*1024)
+#define GZIP_IOBUF_SIZE (16*1024)
 
 /* Included from initramfs et al code */
 STATIC int INIT gunzip(unsigned char *buf, int len,
@@ -55,7 +55,7 @@ STATIC int INIT gunzip(unsigned char *buf, int len,
 	if (buf)
 		zbuf = buf;
 	else {
-		zbuf = malloc(INBUF_LEN);
+		zbuf = malloc(GZIP_IOBUF_SIZE);
 		len = 0;
 	}
 	if (!zbuf) {
@@ -77,7 +77,7 @@ STATIC int INIT gunzip(unsigned char *buf, int len,
 	}
 
 	if (len == 0)
-		len = fill(zbuf, INBUF_LEN);
+		len = fill(zbuf, GZIP_IOBUF_SIZE);
 
 	/* verify the gzip header */
 	if (len < 10 ||
@@ -113,7 +113,7 @@ STATIC int INIT gunzip(unsigned char *buf, int len,
 	while (rc == Z_OK) {
 		if (strm->avail_in == 0) {
 			/* TODO: handle case where both pos and fill are set */
-			len = fill(zbuf, INBUF_LEN);
+			len = fill(zbuf, GZIP_IOBUF_SIZE);
 			if (len < 0) {
 				rc = -1;
 				error("read error");
-- 
GitLab


From b1af4315d823a2b6659c5b14bc17f7bc61878ef4 Mon Sep 17 00:00:00 2001
From: Phillip Lougher <phillip@lougher.demon.co.uk>
Date: Thu, 6 Aug 2009 15:09:31 -0700
Subject: [PATCH 0648/1153] bzip2/lzma: remove nasty uncompressed size hack in
 pre-boot environment

decompress_bunzip2 and decompress_unlzma have a nasty hack that subtracts
4 from the input length if being called in the pre-boot environment.

This is a nasty hack because it relies on the fact that flush = NULL only
when called from the pre-boot environment (i.e.
arch/x86/boot/compressed/misc.c).  initramfs.c/do_mounts_rd.c pass in a
flush buffer (flush != NULL).

This hack prevents the decompressors from being used with flush = NULL by
other callers unless knowledge of the hack is propagated to them.

This patch removes the hack by making decompress (called only from the
pre-boot environment) a wrapper function that subtracts 4 from the input
length before calling the decompressor.

Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 lib/decompress_bunzip2.c | 22 ++++++++++++++++------
 lib/decompress_unlzma.c  | 21 ++++++++++++++++-----
 2 files changed, 32 insertions(+), 11 deletions(-)

diff --git a/lib/decompress_bunzip2.c b/lib/decompress_bunzip2.c
index 708e2a86d87..d3dc9f2beb2 100644
--- a/lib/decompress_bunzip2.c
+++ b/lib/decompress_bunzip2.c
@@ -45,9 +45,11 @@
 */
 
 
-#ifndef STATIC
+#ifdef STATIC
+#define PREBOOT
+#else
 #include <linux/decompress/bunzip2.h>
-#endif /* !STATIC */
+#endif /* STATIC */
 
 #include <linux/decompress/mm.h>
 #include <linux/slab.h>
@@ -681,9 +683,7 @@ STATIC int INIT bunzip2(unsigned char *buf, int len,
 	set_error_fn(error_fn);
 	if (flush)
 		outbuf = malloc(BZIP2_IOBUF_SIZE);
-	else
-		len -= 4; /* Uncompressed size hack active in pre-boot
-			     environment */
+
 	if (!outbuf) {
 		error("Could not allocate output bufer");
 		return -1;
@@ -733,4 +733,14 @@ exit_0:
 	return i;
 }
 
-#define decompress bunzip2
+#ifdef PREBOOT
+STATIC int INIT decompress(unsigned char *buf, int len,
+			int(*fill)(void*, unsigned int),
+			int(*flush)(void*, unsigned int),
+			unsigned char *outbuf,
+			int *pos,
+			void(*error_fn)(char *x))
+{
+	return bunzip2(buf, len - 4, fill, flush, outbuf, pos, error_fn);
+}
+#endif
diff --git a/lib/decompress_unlzma.c b/lib/decompress_unlzma.c
index 32123a1340e..d3f9468e49d 100644
--- a/lib/decompress_unlzma.c
+++ b/lib/decompress_unlzma.c
@@ -29,7 +29,9 @@
  *Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  */
 
-#ifndef STATIC
+#ifdef STATIC
+#define PREBOOT
+#else
 #include <linux/decompress/unlzma.h>
 #endif /* STATIC */
 
@@ -543,9 +545,7 @@ STATIC inline int INIT unlzma(unsigned char *buf, int in_len,
 	int ret = -1;
 
 	set_error_fn(error_fn);
-	if (!flush)
-		in_len -= 4; /* Uncompressed size hack active in pre-boot
-				environment */
+
 	if (buf)
 		inbuf = buf;
 	else
@@ -645,4 +645,15 @@ exit_0:
 	return ret;
 }
 
-#define decompress unlzma
+#ifdef PREBOOT
+STATIC int INIT decompress(unsigned char *buf, int in_len,
+			      int(*fill)(void*, unsigned int),
+			      int(*flush)(void*, unsigned int),
+			      unsigned char *output,
+			      int *posp,
+			      void(*error_fn)(char *x)
+	)
+{
+	return unlzma(buf, in_len - 4, fill, flush, output, posp, error_fn);
+}
+#endif
-- 
GitLab


From 9e5cf0ca2e9b65110ae5f094d7f0f7165cd1bbbb Mon Sep 17 00:00:00 2001
From: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Date: Thu, 6 Aug 2009 15:09:32 -0700
Subject: [PATCH 0649/1153] lib/decompress_*: only include <linux/slab.h> if
 STATIC is not defined

These includes were added by 079effb6933f34b9b1b67b08bd4fd7fb672d16ef
("kmemtrace, kbuild: fix slab.h dependency problem in
lib/decompress_inflate.c") to fix the build when using kmemtrace.  However
this is not necessary when used to create a compressed kernel, and
actually creates issues (brings a lot of things unavailable in the
decompression environment), so don't include it if STATIC is defined.

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 lib/decompress_bunzip2.c | 2 +-
 lib/decompress_inflate.c | 2 +-
 lib/decompress_unlzma.c  | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/lib/decompress_bunzip2.c b/lib/decompress_bunzip2.c
index d3dc9f2beb2..600f473a561 100644
--- a/lib/decompress_bunzip2.c
+++ b/lib/decompress_bunzip2.c
@@ -49,10 +49,10 @@
 #define PREBOOT
 #else
 #include <linux/decompress/bunzip2.h>
+#include <linux/slab.h>
 #endif /* STATIC */
 
 #include <linux/decompress/mm.h>
-#include <linux/slab.h>
 
 #ifndef INT_MAX
 #define INT_MAX 0x7fffffff
diff --git a/lib/decompress_inflate.c b/lib/decompress_inflate.c
index bfe605ac534..68dfce59c1b 100644
--- a/lib/decompress_inflate.c
+++ b/lib/decompress_inflate.c
@@ -19,11 +19,11 @@
 #include "zlib_inflate/inflate.h"
 
 #include "zlib_inflate/infutil.h"
+#include <linux/slab.h>
 
 #endif /* STATIC */
 
 #include <linux/decompress/mm.h>
-#include <linux/slab.h>
 
 #define GZIP_IOBUF_SIZE (16*1024)
 
diff --git a/lib/decompress_unlzma.c b/lib/decompress_unlzma.c
index d3f9468e49d..0b954e04bd3 100644
--- a/lib/decompress_unlzma.c
+++ b/lib/decompress_unlzma.c
@@ -33,10 +33,10 @@
 #define PREBOOT
 #else
 #include <linux/decompress/unlzma.h>
+#include <linux/slab.h>
 #endif /* STATIC */
 
 #include <linux/decompress/mm.h>
-#include <linux/slab.h>
 
 #define	MIN(a, b) (((a) < (b)) ? (a) : (b))
 
-- 
GitLab


From 3440625d78711bee41a84cf29c3d8c579b522666 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Thu, 6 Aug 2009 15:09:34 -0700
Subject: [PATCH 0650/1153] flat: fix uninitialized ptr with shared libs

The new credentials code broke load_flat_shared_library() as it now uses
an uninitialized cred pointer.

Reported-by: Bernd Schmidt <bernds_cb1@t-online.de>
Tested-by: Bernd Schmidt <bernds_cb1@t-online.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/binfmt_flat.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/fs/binfmt_flat.c b/fs/binfmt_flat.c
index 697f6b5f131..e92f229e3c6 100644
--- a/fs/binfmt_flat.c
+++ b/fs/binfmt_flat.c
@@ -828,15 +828,22 @@ static int load_flat_shared_library(int id, struct lib_info *libs)
 	if (IS_ERR(bprm.file))
 		return res;
 
+	bprm.cred = prepare_exec_creds();
+	res = -ENOMEM;
+	if (!bprm.cred)
+		goto out;
+
 	res = prepare_binprm(&bprm);
 
 	if (res <= (unsigned long)-4096)
 		res = load_flat_file(&bprm, libs, id, NULL);
-	if (bprm.file) {
-		allow_write_access(bprm.file);
-		fput(bprm.file);
-		bprm.file = NULL;
-	}
+
+	abort_creds(bprm.cred);
+
+out:
+	allow_write_access(bprm.file);
+	fput(bprm.file);
+
 	return(res);
 }
 
-- 
GitLab


From 4baf8c9201e88546918cbfa61ea8062c38bc1644 Mon Sep 17 00:00:00 2001
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Fri, 7 Aug 2009 13:47:08 -0400
Subject: [PATCH 0651/1153] Btrfs: remove superfluous NULL pointer check in
 btrfs_rename()

This takes care of the following entry from Dan's list:

fs/btrfs/inode.c +4788 btrfs_rename(36) warning: variable derefenced before check 'old_inode'

Reported-by: Dan Carpenter <error27@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eugene Teo <eteo@redhat.com>
Cc: Julia Lawall <julia@diku.dk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/inode.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c
index 3ea827ddf0f..04b53b5ebe5 100644
--- a/fs/btrfs/inode.c
+++ b/fs/btrfs/inode.c
@@ -4806,8 +4806,7 @@ static int btrfs_rename(struct inode *old_dir, struct dentry *old_dentry,
 	 * and the replacement file is large.  Start IO on it now so
 	 * we don't add too much work to the end of the transaction
 	 */
-	if (new_inode && old_inode && S_ISREG(old_inode->i_mode) &&
-	    new_inode->i_size &&
+	if (new_inode && S_ISREG(old_inode->i_mode) && new_inode->i_size &&
 	    old_inode->i_size > BTRFS_ORDERED_OPERATIONS_FLUSH_LIMIT)
 		filemap_flush(old_inode->i_mapping);
 
-- 
GitLab


From 60f2e8f8a07331097a57ec4abcdc680405579377 Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Fri, 7 Aug 2009 13:51:33 -0400
Subject: [PATCH 0652/1153] Btrfs: correct error-handling zlib error handling

find_zlib_workspace returns an ERR_PTR value in an error case instead of NULL.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@match exists@
expression x, E;
statement S1, S2;
@@

x = find_zlib_workspace(...)
... when != x = E
(
*  if (x == NULL || ...) S1 else S2
|
*  if (x == NULL && ...) S1 else S2
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/zlib.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/fs/btrfs/zlib.c b/fs/btrfs/zlib.c
index ecfbce836d3..3e2b90eaa23 100644
--- a/fs/btrfs/zlib.c
+++ b/fs/btrfs/zlib.c
@@ -208,7 +208,7 @@ int btrfs_zlib_compress_pages(struct address_space *mapping,
 	*total_in = 0;
 
 	workspace = find_zlib_workspace();
-	if (!workspace)
+	if (IS_ERR(workspace))
 		return -1;
 
 	if (Z_OK != zlib_deflateInit(&workspace->def_strm, 3)) {
@@ -366,7 +366,7 @@ int btrfs_zlib_decompress_biovec(struct page **pages_in,
 	char *kaddr;
 
 	workspace = find_zlib_workspace();
-	if (!workspace)
+	if (IS_ERR(workspace))
 		return -ENOMEM;
 
 	data_in = kmap(pages_in[page_in_index]);
@@ -547,7 +547,7 @@ int btrfs_zlib_decompress(unsigned char *data_in,
 		return -ENOMEM;
 
 	workspace = find_zlib_workspace();
-	if (!workspace)
+	if (IS_ERR(workspace))
 		return -ENOMEM;
 
 	workspace->inf_strm.next_in = data_in;
-- 
GitLab


From ceab36edd3d3ad3ffd01d41d6d1e05ac1ff8357e Mon Sep 17 00:00:00 2001
From: Yan Zheng <zheng.yan@oracle.com>
Date: Fri, 7 Aug 2009 13:51:33 -0400
Subject: [PATCH 0653/1153] Btrfs: fix balancing oops when
 invalidate_inode_pages2 returns EBUSY

invalidate_inode_pages2_range may return -EBUSY occasionally
which results Oops. This patch fixes the issue by moving
invalidate_inode_pages2_range into a loop and keeping calling
it until the return value is not -EBUSY.

The EBUSY return is temporary, and can happen when the btrfs release page
function is unable to release a page because the EXTENT_LOCK
bit is set.

Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
---
 fs/btrfs/relocation.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/fs/btrfs/relocation.c b/fs/btrfs/relocation.c
index e71264d1c2c..c04f7f21260 100644
--- a/fs/btrfs/relocation.c
+++ b/fs/btrfs/relocation.c
@@ -2553,8 +2553,13 @@ int relocate_inode_pages(struct inode *inode, u64 start, u64 len)
 	last_index = (start + len - 1) >> PAGE_CACHE_SHIFT;
 
 	/* make sure the dirty trick played by the caller work */
-	ret = invalidate_inode_pages2_range(inode->i_mapping,
-					    first_index, last_index);
+	while (1) {
+		ret = invalidate_inode_pages2_range(inode->i_mapping,
+						    first_index, last_index);
+		if (ret != -EBUSY)
+			break;
+		schedule_timeout(HZ/10);
+	}
 	if (ret)
 		goto out_unlock;
 
-- 
GitLab


From e7432675f8ca868a4af365759a8d4c3779a3d922 Mon Sep 17 00:00:00 2001
From: Sunil Mushran <sunil.mushran@oracle.com>
Date: Thu, 6 Aug 2009 16:12:58 -0700
Subject: [PATCH 0654/1153] ocfs2: Initialize the cluster we're writing to in a
 non-sparse extend

In a non-sparse extend, we correctly allocate (and zero) the clusters between
the old_i_size and pos, but we don't zero the portions of the cluster we're
writing to outside of pos<->len.

It handles clustersize > pagesize and blocksize < pagesize.

[Cleaned up by Joel Becker.]

Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/aops.c | 66 +++++++++++++++++++++++++++++++++++--------------
 1 file changed, 47 insertions(+), 19 deletions(-)

diff --git a/fs/ocfs2/aops.c b/fs/ocfs2/aops.c
index e511df10145..b401654011a 100644
--- a/fs/ocfs2/aops.c
+++ b/fs/ocfs2/aops.c
@@ -895,18 +895,17 @@ struct ocfs2_write_cluster_desc {
 	 */
 	unsigned	c_new;
 	unsigned	c_unwritten;
+	unsigned	c_needs_zero;
 };
 
-static inline int ocfs2_should_zero_cluster(struct ocfs2_write_cluster_desc *d)
-{
-	return d->c_new || d->c_unwritten;
-}
-
 struct ocfs2_write_ctxt {
 	/* Logical cluster position / len of write */
 	u32				w_cpos;
 	u32				w_clen;
 
+	/* First cluster allocated in a nonsparse extend */
+	u32				w_first_new_cpos;
+
 	struct ocfs2_write_cluster_desc	w_desc[OCFS2_MAX_CLUSTERS_PER_PAGE];
 
 	/*
@@ -984,6 +983,7 @@ static int ocfs2_alloc_write_ctxt(struct ocfs2_write_ctxt **wcp,
 		return -ENOMEM;
 
 	wc->w_cpos = pos >> osb->s_clustersize_bits;
+	wc->w_first_new_cpos = UINT_MAX;
 	cend = (pos + len - 1) >> osb->s_clustersize_bits;
 	wc->w_clen = cend - wc->w_cpos + 1;
 	get_bh(di_bh);
@@ -1218,20 +1218,18 @@ out:
  */
 static int ocfs2_write_cluster(struct address_space *mapping,
 			       u32 phys, unsigned int unwritten,
+			       unsigned int should_zero,
 			       struct ocfs2_alloc_context *data_ac,
 			       struct ocfs2_alloc_context *meta_ac,
 			       struct ocfs2_write_ctxt *wc, u32 cpos,
 			       loff_t user_pos, unsigned user_len)
 {
-	int ret, i, new, should_zero = 0;
+	int ret, i, new;
 	u64 v_blkno, p_blkno;
 	struct inode *inode = mapping->host;
 	struct ocfs2_extent_tree et;
 
 	new = phys == 0 ? 1 : 0;
-	if (new || unwritten)
-		should_zero = 1;
-
 	if (new) {
 		u32 tmp_pos;
 
@@ -1342,7 +1340,9 @@ static int ocfs2_write_cluster_by_desc(struct address_space *mapping,
 			local_len = osb->s_clustersize - cluster_off;
 
 		ret = ocfs2_write_cluster(mapping, desc->c_phys,
-					  desc->c_unwritten, data_ac, meta_ac,
+					  desc->c_unwritten,
+					  desc->c_needs_zero,
+					  data_ac, meta_ac,
 					  wc, desc->c_cpos, pos, local_len);
 		if (ret) {
 			mlog_errno(ret);
@@ -1392,14 +1392,14 @@ static void ocfs2_set_target_boundaries(struct ocfs2_super *osb,
 		 * newly allocated cluster.
 		 */
 		desc = &wc->w_desc[0];
-		if (ocfs2_should_zero_cluster(desc))
+		if (desc->c_needs_zero)
 			ocfs2_figure_cluster_boundaries(osb,
 							desc->c_cpos,
 							&wc->w_target_from,
 							NULL);
 
 		desc = &wc->w_desc[wc->w_clen - 1];
-		if (ocfs2_should_zero_cluster(desc))
+		if (desc->c_needs_zero)
 			ocfs2_figure_cluster_boundaries(osb,
 							desc->c_cpos,
 							NULL,
@@ -1467,13 +1467,28 @@ static int ocfs2_populate_write_desc(struct inode *inode,
 			phys++;
 		}
 
+		/*
+		 * If w_first_new_cpos is < UINT_MAX, we have a non-sparse
+		 * file that got extended.  w_first_new_cpos tells us
+		 * where the newly allocated clusters are so we can
+		 * zero them.
+		 */
+		if (desc->c_cpos >= wc->w_first_new_cpos) {
+			BUG_ON(phys == 0);
+			desc->c_needs_zero = 1;
+		}
+
 		desc->c_phys = phys;
 		if (phys == 0) {
 			desc->c_new = 1;
+			desc->c_needs_zero = 1;
 			*clusters_to_alloc = *clusters_to_alloc + 1;
 		}
-		if (ext_flags & OCFS2_EXT_UNWRITTEN)
+
+		if (ext_flags & OCFS2_EXT_UNWRITTEN) {
 			desc->c_unwritten = 1;
+			desc->c_needs_zero = 1;
+		}
 
 		num_clusters--;
 	}
@@ -1633,10 +1648,13 @@ static int ocfs2_expand_nonsparse_inode(struct inode *inode, loff_t pos,
 	if (newsize <= i_size_read(inode))
 		return 0;
 
-	ret = ocfs2_extend_no_holes(inode, newsize, newsize - len);
+	ret = ocfs2_extend_no_holes(inode, newsize, pos);
 	if (ret)
 		mlog_errno(ret);
 
+	wc->w_first_new_cpos =
+		ocfs2_clusters_for_bytes(inode->i_sb, i_size_read(inode));
+
 	return ret;
 }
 
@@ -1645,7 +1663,7 @@ int ocfs2_write_begin_nolock(struct address_space *mapping,
 			     struct page **pagep, void **fsdata,
 			     struct buffer_head *di_bh, struct page *mmap_page)
 {
-	int ret, credits = OCFS2_INODE_UPDATE_CREDITS;
+	int ret, cluster_of_pages, credits = OCFS2_INODE_UPDATE_CREDITS;
 	unsigned int clusters_to_alloc, extents_to_split;
 	struct ocfs2_write_ctxt *wc;
 	struct inode *inode = mapping->host;
@@ -1723,8 +1741,19 @@ int ocfs2_write_begin_nolock(struct address_space *mapping,
 
 	}
 
-	ocfs2_set_target_boundaries(osb, wc, pos, len,
-				    clusters_to_alloc + extents_to_split);
+	/*
+	 * We have to zero sparse allocated clusters, unwritten extent clusters,
+	 * and non-sparse clusters we just extended.  For non-sparse writes,
+	 * we know zeros will only be needed in the first and/or last cluster.
+	 */
+	if (clusters_to_alloc || extents_to_split ||
+	    wc->w_desc[0].c_needs_zero ||
+	    wc->w_desc[wc->w_clen - 1].c_needs_zero)
+		cluster_of_pages = 1;
+	else
+		cluster_of_pages = 0;
+
+	ocfs2_set_target_boundaries(osb, wc, pos, len, cluster_of_pages);
 
 	handle = ocfs2_start_trans(osb, credits);
 	if (IS_ERR(handle)) {
@@ -1757,8 +1786,7 @@ int ocfs2_write_begin_nolock(struct address_space *mapping,
 	 * extent.
 	 */
 	ret = ocfs2_grab_pages_for_write(mapping, wc, wc->w_cpos, pos,
-					 clusters_to_alloc + extents_to_split,
-					 mmap_page);
+					 cluster_of_pages, mmap_page);
 	if (ret) {
 		mlog_errno(ret);
 		goto out_quota;
-- 
GitLab


From 8a57a9dda760ea7845390f1cd36f3eb2a49391d8 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Thu, 6 Aug 2009 16:07:50 -0700
Subject: [PATCH 0655/1153] ocfs2: keep index within status_map[]

Do not exceed array status_map[]

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/stack_o2cb.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/fs/ocfs2/stack_o2cb.c b/fs/ocfs2/stack_o2cb.c
index 3f661376a2d..e49c4105026 100644
--- a/fs/ocfs2/stack_o2cb.c
+++ b/fs/ocfs2/stack_o2cb.c
@@ -17,6 +17,7 @@
  * General Public License for more details.
  */
 
+#include <linux/kernel.h>
 #include <linux/crc32.h>
 #include <linux/module.h>
 
@@ -153,7 +154,7 @@ static int status_map[] = {
 
 static int dlm_status_to_errno(enum dlm_status status)
 {
-	BUG_ON(status > (sizeof(status_map) / sizeof(status_map[0])));
+	BUG_ON(status < 0 || status >= ARRAY_SIZE(status_map));
 
 	return status_map[status];
 }
-- 
GitLab


From 49276560c9004fce24c42e3c0ad75f34d956fc63 Mon Sep 17 00:00:00 2001
From: Khanh-Dang Nguyen Thu Lam <kdntl@yahoo.fr>
Date: Tue, 28 Jul 2009 19:41:17 +0200
Subject: [PATCH 0656/1153] USB: pl2303: New vendor and product id

I am submitting a patch for the pl2303 driver.  This patch adds support
for the "Sony QN-3USB" cable (vendor=0x054c, product=0x0437).  This USB
cable is a so-called data cable used to connect a Sony mobile phone to a
computer.  Supported models are Sony CMD-J5, J6, J7, J16, J26, J70 and
Z7.

I have used this patch with my Sony CMD-J70 for several days and I
haven't encountered any kernel/hardware issue.


From: Khanh-Dang Nguyen Thu Lam <kdntl@yahoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/pl2303.c | 1 +
 drivers/usb/serial/pl2303.h | 4 ++++
 2 files changed, 5 insertions(+)

diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index 7d15bfa7c2d..3e86815b270 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -95,6 +95,7 @@ static struct usb_device_id id_table [] = {
 	{ USB_DEVICE(SUPERIAL_VENDOR_ID, SUPERIAL_PRODUCT_ID) },
 	{ USB_DEVICE(HP_VENDOR_ID, HP_LD220_PRODUCT_ID) },
 	{ USB_DEVICE(CRESSI_VENDOR_ID, CRESSI_EDY_PRODUCT_ID) },
+	{ USB_DEVICE(SONY_VENDOR_ID, SONY_QN3USB_PRODUCT_ID) },
 	{ }					/* Terminating entry */
 };
 
diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h
index 12aac7d2462..ee9505e1dd9 100644
--- a/drivers/usb/serial/pl2303.h
+++ b/drivers/usb/serial/pl2303.h
@@ -126,3 +126,7 @@
 /* Cressi Edy (diving computer) PC interface */
 #define CRESSI_VENDOR_ID	0x04b8
 #define CRESSI_EDY_PRODUCT_ID	0x0521
+
+/* Sony, USB data cable for CMD-Jxx mobile phones */
+#define SONY_VENDOR_ID		0x054c
+#define SONY_QN3USB_PRODUCT_ID	0x0437
-- 
GitLab


From 18753ebc8a98efe0e8ff6167afb31cef220c8e50 Mon Sep 17 00:00:00 2001
From: Michael Buesch <mb@bu3sch.de>
Date: Wed, 29 Jul 2009 11:39:03 +0200
Subject: [PATCH 0657/1153] USB: devio: Properly do access_ok() checks

access_ok() checks must be done on every part of the userspace structure
that is accessed. If access_ok() on one part of the struct succeeded, it
does not imply it will succeed on other parts of the struct. (Does
depend on the architecture implementation of access_ok()).

This changes the __get_user() users to first check access_ok() on the
data structure.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/devio.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index 38b8bce782d..e192fa05f8a 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -1321,7 +1321,8 @@ static int get_urb32(struct usbdevfs_urb *kurb,
 		     struct usbdevfs_urb32 __user *uurb)
 {
 	__u32  uptr;
-	if (get_user(kurb->type, &uurb->type) ||
+	if (!access_ok(VERIFY_READ, uurb, sizeof(*uurb)) ||
+	    __get_user(kurb->type, &uurb->type) ||
 	    __get_user(kurb->endpoint, &uurb->endpoint) ||
 	    __get_user(kurb->status, &uurb->status) ||
 	    __get_user(kurb->flags, &uurb->flags) ||
@@ -1536,8 +1537,9 @@ static int proc_ioctl_compat(struct dev_state *ps, compat_uptr_t arg)
 	u32 udata;
 
 	uioc = compat_ptr((long)arg);
-	if (get_user(ctrl.ifno, &uioc->ifno) ||
-	    get_user(ctrl.ioctl_code, &uioc->ioctl_code) ||
+	if (!access_ok(VERIFY_READ, uioc, sizeof(*uioc)) ||
+	    __get_user(ctrl.ifno, &uioc->ifno) ||
+	    __get_user(ctrl.ioctl_code, &uioc->ioctl_code) ||
 	    __get_user(udata, &uioc->data))
 		return -EFAULT;
 	ctrl.data = compat_ptr(udata);
-- 
GitLab


From e8e2ff462dd92693f29eb848f42d3eb720390d59 Mon Sep 17 00:00:00 2001
From: "Gupta, Ajay Kumar" <ajay.gupta@ti.com>
Date: Wed, 29 Jul 2009 11:58:57 +0530
Subject: [PATCH 0658/1153] USB: musb: fix the nop registration for OMAP3EVM

OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.

Cleanups being done:
	- Remove unwanted code in usb-musb.c file
	- Register NOP in OMAP3EVM board file using
	  usb_nop_xceiv_register().
	- Select NOP_USB_XCEIV for OMAP3EVM boards.
	- Don't enable TWL4030_USB in omap3_evm_defconfig

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 arch/arm/configs/omap3_evm_defconfig |  2 +-
 arch/arm/mach-omap2/board-omap3evm.c |  5 +++++
 arch/arm/mach-omap2/usb-musb.c       | 21 ---------------------
 drivers/usb/musb/Kconfig             |  1 +
 4 files changed, 7 insertions(+), 22 deletions(-)

diff --git a/arch/arm/configs/omap3_evm_defconfig b/arch/arm/configs/omap3_evm_defconfig
index 28be17fbc15..d5ff4776cd0 100644
--- a/arch/arm/configs/omap3_evm_defconfig
+++ b/arch/arm/configs/omap3_evm_defconfig
@@ -1107,7 +1107,7 @@ CONFIG_USB_ZERO=m
 CONFIG_USB_OTG_UTILS=y
 # CONFIG_USB_GPIO_VBUS is not set
 # CONFIG_ISP1301_OMAP is not set
-CONFIG_TWL4030_USB=y
+# CONFIG_TWL4030_USB is not set
 # CONFIG_NOP_USB_XCEIV is not set
 CONFIG_MMC=y
 # CONFIG_MMC_DEBUG is not set
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index d3cc145814d..cf3dd771a67 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -25,6 +25,7 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
 #include <linux/i2c/twl4030.h>
+#include <linux/usb/otg.h>
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
@@ -307,6 +308,10 @@ static void __init omap3_evm_init(void)
 				ARRAY_SIZE(omap3evm_spi_board_info));
 
 	omap_serial_init();
+#ifdef CONFIG_NOP_USB_XCEIV
+	/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
+	usb_nop_xceiv_register();
+#endif
 	usb_musb_init();
 	ads7846_dev_init();
 }
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
index d85296dc896..739e59e8025 100644
--- a/arch/arm/mach-omap2/usb-musb.c
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -155,20 +155,6 @@ static struct platform_device musb_device = {
 	.resource	= musb_resources,
 };
 
-#ifdef CONFIG_NOP_USB_XCEIV
-static u64 nop_xceiv_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device nop_xceiv_device = {
-	.name		= "nop_usb_xceiv",
-	.id		= -1,
-	.dev = {
-		.dma_mask		= &nop_xceiv_dmamask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data		= NULL,
-	},
-};
-#endif
-
 void __init usb_musb_init(void)
 {
 	if (cpu_is_omap243x())
@@ -183,13 +169,6 @@ void __init usb_musb_init(void)
 	 */
 	musb_plat.clock = "ick";
 
-#ifdef CONFIG_NOP_USB_XCEIV
-	if (platform_device_register(&nop_xceiv_device) < 0) {
-		printk(KERN_ERR "Unable to register NOP-XCEIV device\n");
-		return;
-	}
-#endif
-
 	if (platform_device_register(&musb_device) < 0) {
 		printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n");
 		return;
diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig
index 70073b157f0..803adcb5ac1 100644
--- a/drivers/usb/musb/Kconfig
+++ b/drivers/usb/musb/Kconfig
@@ -12,6 +12,7 @@ config USB_MUSB_HDRC
 	depends on !SUPERH
 	select NOP_USB_XCEIV if ARCH_DAVINCI
 	select TWL4030_USB if MACH_OMAP_3430SDP
+	select NOP_USB_XCEIV if MACH_OMAP3EVM
 	select USB_OTG_UTILS
 	tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)'
 	help
-- 
GitLab


From 01105a246345f011fde64d24a601090b646e9e4c Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Thu, 30 Jul 2009 15:28:14 -0400
Subject: [PATCH 0659/1153] USB: usbfs: fix -ENOENT error code to be -ENODEV

This patch (as1272) changes the error code returned when an open call
for a USB device node fails to locate the corresponding device.  The
appropriate error code is -ENODEV, not -ENOENT.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/devio.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index e192fa05f8a..4247eccf858 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -595,7 +595,7 @@ static int usbdev_open(struct inode *inode, struct file *file)
 	if (!ps)
 		goto out;
 
-	ret = -ENOENT;
+	ret = -ENODEV;
 
 	/* usbdev device-node */
 	if (imajor(inode) == USB_DEVICE_MAJOR)
-- 
GitLab


From 7a0f0d951273eee889c2441846842348ebc00a2a Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Fri, 31 Jul 2009 10:40:22 -0400
Subject: [PATCH 0660/1153] USB: EHCI: fix two new bugs related to
 Clear-TT-Buffer

This patch (as1273) fixes two(!) bugs introduced by the new
Clear-TT-Buffer implementation in ehci-hcd.

	It is now possible for an idle QH to have some URBs on its
	queue -- this will happen if a Clear-TT-Buffer is pending for
	the QH's endpoint.  Consequently we should not issue a warning
	when someone tries to unlink an URB from an idle QH; instead
	we should process the request immediately.

	The refcounts for QHs could get messed up, because
	submit_async() would increment the refcount when calling
	qh_link_async() and qh_link_async() would then refuse to link
	the QH into the schedule if a Clear-TT-Buffer was pending.
	Instead we should increment the refcount only when the QH
	actually is added to the schedule.  The current code tries to
	be clever by leaving the refcount alone if an unlink is
	immediately followed by a relink; the patch changes this to an
	unconditional decrement and increment (although they occur in
	the opposite order).

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Tested-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/ehci-hcd.c | 3 ++-
 drivers/usb/host/ehci-q.c   | 6 +++---
 2 files changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index 7d03549c333..11c627ce602 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -903,7 +903,8 @@ static int ehci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
 			/* already started */
 			break;
 		case QH_STATE_IDLE:
-			WARN_ON(1);
+			/* QH might be waiting for a Clear-TT-Buffer */
+			qh_completions(ehci, qh);
 			break;
 		}
 		break;
diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c
index 9a1384747f3..b2738050557 100644
--- a/drivers/usb/host/ehci-q.c
+++ b/drivers/usb/host/ehci-q.c
@@ -940,6 +940,7 @@ static void qh_link_async (struct ehci_hcd *ehci, struct ehci_qh *qh)
 	head->qh_next.qh = qh;
 	head->hw_next = dma;
 
+	qh_get(qh);
 	qh->xacterrs = QH_XACTERR_MAX;
 	qh->qh_state = QH_STATE_LINKED;
 	/* qtd completions reported later by interrupt */
@@ -1080,7 +1081,7 @@ submit_async (
 	 * the HC and TT handle it when the TT has a buffer ready.
 	 */
 	if (likely (qh->qh_state == QH_STATE_IDLE))
-		qh_link_async (ehci, qh_get (qh));
+		qh_link_async(ehci, qh);
  done:
 	spin_unlock_irqrestore (&ehci->lock, flags);
 	if (unlikely (qh == NULL))
@@ -1115,8 +1116,6 @@ static void end_unlink_async (struct ehci_hcd *ehci)
 			&& HC_IS_RUNNING (ehci_to_hcd(ehci)->state))
 		qh_link_async (ehci, qh);
 	else {
-		qh_put (qh);		// refcount from async list
-
 		/* it's not free to turn the async schedule on/off; leave it
 		 * active but idle for a while once it empties.
 		 */
@@ -1124,6 +1123,7 @@ static void end_unlink_async (struct ehci_hcd *ehci)
 				&& ehci->async->qh_next.qh == NULL)
 			timer_action (ehci, TIMER_ASYNC_OFF);
 	}
+	qh_put(qh);			/* refcount from async list */
 
 	if (next) {
 		ehci->reclaim = NULL;
-- 
GitLab


From ef4638f955f2c4a667c8af20769d03f5ed3781ca Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Fri, 31 Jul 2009 10:41:40 -0400
Subject: [PATCH 0661/1153] USB: EHCI: fix counting of transaction error
 retries

This patch (as1274) simplifies the counting of transaction-error
retries.  Now we will count up from 0 to QH_XACTERR_MAX instead of
down from QH_XACTERR_MAX to 0.

The patch also fixes a small bug: qh->xacterr was not getting
initialized for interrupt endpoints.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/ehci-q.c     | 9 ++++-----
 drivers/usb/host/ehci-sched.c | 1 +
 2 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c
index b2738050557..7673554fa64 100644
--- a/drivers/usb/host/ehci-q.c
+++ b/drivers/usb/host/ehci-q.c
@@ -375,12 +375,11 @@ qh_completions (struct ehci_hcd *ehci, struct ehci_qh *qh)
 				 */
 				if ((token & QTD_STS_XACT) &&
 						QTD_CERR(token) == 0 &&
-						--qh->xacterrs > 0 &&
+						++qh->xacterrs < QH_XACTERR_MAX &&
 						!urb->unlinked) {
 					ehci_dbg(ehci,
 	"detected XactErr len %zu/%zu retry %d\n",
-	qtd->length - QTD_LENGTH(token), qtd->length,
-	QH_XACTERR_MAX - qh->xacterrs);
+	qtd->length - QTD_LENGTH(token), qtd->length, qh->xacterrs);
 
 					/* reset the token in the qtd and the
 					 * qh overlay (which still contains
@@ -494,7 +493,7 @@ halt:
 		last = qtd;
 
 		/* reinit the xacterr counter for the next qtd */
-		qh->xacterrs = QH_XACTERR_MAX;
+		qh->xacterrs = 0;
 	}
 
 	/* last urb's completion might still need calling */
@@ -941,7 +940,7 @@ static void qh_link_async (struct ehci_hcd *ehci, struct ehci_qh *qh)
 	head->hw_next = dma;
 
 	qh_get(qh);
-	qh->xacterrs = QH_XACTERR_MAX;
+	qh->xacterrs = 0;
 	qh->qh_state = QH_STATE_LINKED;
 	/* qtd completions reported later by interrupt */
 }
diff --git a/drivers/usb/host/ehci-sched.c b/drivers/usb/host/ehci-sched.c
index 74f7f83b29a..edd61ee9032 100644
--- a/drivers/usb/host/ehci-sched.c
+++ b/drivers/usb/host/ehci-sched.c
@@ -542,6 +542,7 @@ static int qh_link_periodic (struct ehci_hcd *ehci, struct ehci_qh *qh)
 		}
 	}
 	qh->qh_state = QH_STATE_LINKED;
+	qh->xacterrs = 0;
 	qh_get (qh);
 
 	/* update per-qh bandwidth for usbfs */
-- 
GitLab


From c47aacc67a3d26dfab9c9b8965975ed2b2010b30 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Marko=20H=C3=A4nninen?= <bugitus@gmail.com>
Date: Fri, 31 Jul 2009 22:32:39 +0300
Subject: [PATCH 0662/1153] USB: ftdi_sio: add vendor and product id for Bayer
 glucose meter serial converter cable
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Attached patch adds USB vendor and product IDs for Bayer's USB to serial
converter cable used by Bayer blood glucose meters. It seems to be a
FT232RL based device and works without any problem with ftdi_sio driver
when this patch is applied. See: http://winglucofacts.com/cables/


Signed-off-by: Marko Hänninen <bugitus@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/ftdi_sio.c | 1 +
 drivers/usb/serial/ftdi_sio.h | 7 +++++++
 2 files changed, 8 insertions(+)

diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index b574878c78b..500087ea58a 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -699,6 +699,7 @@ static struct usb_device_id id_table_combined [] = {
 		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
 	{ USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) },
 	{ USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) },
+	{ USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) },
 	{ },					/* Optional parameter entry */
 	{ }					/* Terminating entry */
 };
diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h
index 24dbd99e87d..f203b2a5130 100644
--- a/drivers/usb/serial/ftdi_sio.h
+++ b/drivers/usb/serial/ftdi_sio.h
@@ -953,6 +953,13 @@
 #define GN_OTOMETRICS_VID	0x0c33	/* Vendor ID */
 #define AURICAL_USB_PID		0x0010	/* Aurical USB Audiometer */
 
+/*
+ * Bayer Ascensia Contour blood glucose meter USB-converter cable.
+ * http://winglucofacts.com/cables/
+ */
+#define BAYER_VID                      0x1A79
+#define BAYER_CONTOUR_CABLE_PID        0x6001
+
 /*
  *   BmRequestType:  1100 0000b
  *   bRequest:       FTDI_E2_READ
-- 
GitLab


From 50d0678e2026c18e4147f0b16b5853113659b82d Mon Sep 17 00:00:00 2001
From: Dhaval Vasa <dhaval.vasa@einfochips.com>
Date: Fri, 7 Aug 2009 17:26:49 +0530
Subject: [PATCH 0663/1153] USB: ftdi_sio: add product_id for Marvell OpenRD
 Base, Client

reference:
http://www.open-rd.org

Signed-off-by: Dhaval Vasa <dhaval.vasa@einfochips.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/ftdi_sio.c | 2 ++
 drivers/usb/serial/ftdi_sio.h | 7 +++++++
 2 files changed, 9 insertions(+)

diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 500087ea58a..8fec5d4455c 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -700,6 +700,8 @@ static struct usb_device_id id_table_combined [] = {
 	{ USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) },
 	{ USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) },
 	{ USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) },
+	{ USB_DEVICE(FTDI_VID, MARVELL_OPENRD_PID),
+		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
 	{ },					/* Optional parameter entry */
 	{ }					/* Terminating entry */
 };
diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h
index f203b2a5130..8c92b88166a 100644
--- a/drivers/usb/serial/ftdi_sio.h
+++ b/drivers/usb/serial/ftdi_sio.h
@@ -960,6 +960,13 @@
 #define BAYER_VID                      0x1A79
 #define BAYER_CONTOUR_CABLE_PID        0x6001
 
+/*
+ * Marvell OpenRD Base, Client
+ * http://www.open-rd.org
+ * OpenRD Base, Client use VID 0x0403
+ */
+#define MARVELL_OPENRD_PID	0x9e90
+
 /*
  *   BmRequestType:  1100 0000b
  *   bRequest:       FTDI_E2_READ
-- 
GitLab


From c15e3ca1d822abba78c00b1ffc3e7b382a50396e Mon Sep 17 00:00:00 2001
From: Rogerio Brito <rbrito@ime.usp.br>
Date: Thu, 6 Aug 2009 15:20:19 -0700
Subject: [PATCH 0664/1153] USB: storage: include Prolific Technology USB drive
 in unusual_devs list

Add a quirk entry for the Leading Driver UD-11 usb flash drive.

As Alan Stern told me, the device doesn't deal correctly with the
locking media feature of the device, and this patch incorporates it.

Compiled, tested, working.

Signed-off-by: Rogerio Brito <rbrito@ime.usp.br>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/storage/unusual_devs.h | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index 1b9c5dd0fb2..7477d411959 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -838,6 +838,13 @@ UNUSUAL_DEV( 0x066f, 0x8000, 0x0001, 0x0001,
 		US_SC_DEVICE, US_PR_DEVICE, NULL,
 		US_FL_FIX_CAPACITY ),
 
+/* Reported by Rogerio Brito <rbrito@ime.usp.br> */
+UNUSUAL_DEV( 0x067b, 0x2317, 0x0001, 0x001,
+		"Prolific Technology, Inc.",
+		"Mass Storage Device",
+		US_SC_DEVICE, US_PR_DEVICE, NULL,
+		US_FL_NOT_LOCKABLE ),
+
 /* Reported by Richard -=[]=- <micro_flyer@hotmail.com> */
 /* Change to bcdDeviceMin (0x0100 to 0x0001) reported by
  * Thomas Bartosik <tbartdev@gmx-topmail.de> */
-- 
GitLab


From cf7fdd57f978d40ceb9a0f58a25f5cf9c84d6f33 Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Tue, 4 Aug 2009 23:52:09 +0200
Subject: [PATCH 0665/1153] USB: fix oops on disconnect in cdc-acm

This patch fixes an oops caused when during an unplug a device's table
of endpoints is zeroed before the driver is notified. A pointer to
the endpoint must be cached.

this fixes a regression caused by commit
5186ffee2320942c3dc9745f7930e0eb15329ca6
Therefore it should go into 2.6.31

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/class/cdc-acm.c | 10 +++++-----
 drivers/usb/class/cdc-acm.h |  2 ++
 2 files changed, 7 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
index e1f89416ef8..2bfc41ece0e 100644
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -387,7 +387,6 @@ static void acm_rx_tasklet(unsigned long _acm)
 	struct acm_ru *rcv;
 	unsigned long flags;
 	unsigned char throttled;
-	struct usb_host_endpoint *ep;
 
 	dbg("Entering acm_rx_tasklet");
 
@@ -463,14 +462,12 @@ urbs:
 
 		rcv->buffer = buf;
 
-		ep = (usb_pipein(acm->rx_endpoint) ? acm->dev->ep_in : acm->dev->ep_out)
-				[usb_pipeendpoint(acm->rx_endpoint)];
-		if (usb_endpoint_xfer_int(&ep->desc))
+		if (acm->is_int_ep)
 			usb_fill_int_urb(rcv->urb, acm->dev,
 					 acm->rx_endpoint,
 					 buf->base,
 					 acm->readsize,
-					 acm_read_bulk, rcv, ep->desc.bInterval);
+					 acm_read_bulk, rcv, acm->bInterval);
 		else
 			usb_fill_bulk_urb(rcv->urb, acm->dev,
 					  acm->rx_endpoint,
@@ -1183,6 +1180,9 @@ made_compressed_probe:
 	spin_lock_init(&acm->read_lock);
 	mutex_init(&acm->mutex);
 	acm->rx_endpoint = usb_rcvbulkpipe(usb_dev, epread->bEndpointAddress);
+	acm->is_int_ep = usb_endpoint_xfer_int(epread);
+	if (acm->is_int_ep)
+		acm->bInterval = epread->bInterval;
 	tty_port_init(&acm->port);
 	acm->port.ops = &acm_port_ops;
 
diff --git a/drivers/usb/class/cdc-acm.h b/drivers/usb/class/cdc-acm.h
index 1602324808b..c4a0ee8ffcc 100644
--- a/drivers/usb/class/cdc-acm.h
+++ b/drivers/usb/class/cdc-acm.h
@@ -126,6 +126,8 @@ struct acm {
 	unsigned int ctrl_caps;				/* control capabilities from the class specific header */
 	unsigned int susp_count;			/* number of suspended interfaces */
 	int combined_interfaces:1;			/* control and data collapsed */
+	int is_int_ep:1;				/* interrupt endpoints contrary to spec used */
+	u8 bInterval;
 	struct acm_wb *delayed_wb;			/* write queued for a device about to be woken */
 };
 
-- 
GitLab


From 4d2da07bc876fc5bc455e0721df388a3db7e4ba5 Mon Sep 17 00:00:00 2001
From: Jakob Gruber <jakob.gruber@kabelnet.at>
Date: Thu, 30 Jul 2009 20:37:36 +0200
Subject: [PATCH 0666/1153] Staging: rt2870: Add USB ID for Linksys, Planex
 Communications, Belkin

Linksys WUSB100, Belkin F5D8053 N, Planex Communications unknown model.

Signed-off-by: Jakob Gruber <jakob.gruber@kabelnet.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/staging/rt2870/rt2870.h | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/staging/rt2870/rt2870.h b/drivers/staging/rt2870/rt2870.h
index 29e3b53e52a..10e1640d61e 100644
--- a/drivers/staging/rt2870/rt2870.h
+++ b/drivers/staging/rt2870/rt2870.h
@@ -79,6 +79,7 @@
 {	\
 	{USB_DEVICE(0x148F,0x2770)}, /* Ralink */		\
 	{USB_DEVICE(0x1737,0x0071)}, /* Linksys WUSB600N */	\
+	{USB_DEVICE(0x1737,0x0070)}, /* Linksys */	\
 	{USB_DEVICE(0x148F,0x2870)}, /* Ralink */		\
 	{USB_DEVICE(0x148F,0x3070)}, /* Ralink */		\
 	{USB_DEVICE(0x0B05,0x1731)}, /* Asus */			\
@@ -93,12 +94,14 @@
 	{USB_DEVICE(0x14B2,0x3C06)}, /* Conceptronic */		\
 	{USB_DEVICE(0x14B2,0x3C28)}, /* Conceptronic */		\
 	{USB_DEVICE(0x2019,0xED06)}, /* Planex Communications, Inc. */		\
+	{USB_DEVICE(0x2019,0xED14)}, /* Planex Communications, Inc. */		\
 	{USB_DEVICE(0x2019,0xAB25)}, /* Planex Communications, Inc. RT3070 */		\
 	{USB_DEVICE(0x07D1,0x3C09)}, /* D-Link */		\
 	{USB_DEVICE(0x07D1,0x3C11)}, /* D-Link */		\
 	{USB_DEVICE(0x14B2,0x3C07)}, /* AL */			\
 	{USB_DEVICE(0x14B2,0x3C12)}, /* AL */           \
 	{USB_DEVICE(0x050D,0x8053)}, /* Belkin */		\
+	{USB_DEVICE(0x050D,0x815C)}, /* Belkin */		\
 	{USB_DEVICE(0x14B2,0x3C23)}, /* Airlink */		\
 	{USB_DEVICE(0x14B2,0x3C27)}, /* Airlink */		\
 	{USB_DEVICE(0x07AA,0x002F)}, /* Corega */		\
-- 
GitLab


From 2c63abf9e8a51dec886da482dfd8ae752581a61c Mon Sep 17 00:00:00 2001
From: Mike Galbraith <efault@gmx.de>
Date: Fri, 31 Jul 2009 07:14:04 +0200
Subject: [PATCH 0667/1153] Staging: rt2870: Revert d44ca7 Removal of
 kernel_thread() API

Staging: rt2870: Revert d44ca7 Removal of kernel_thread() API

The sanity check this patch introduced triggers on shutdown, apparently due to
threads having already exited by the time BUG_ON() is reached.

Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Peter Teoh <htmldeveloper@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/staging/rt2860/rt_linux.h             | 13 ++--
 drivers/staging/rt2870/2870_main_dev.c        | 67 +++++++++++++------
 .../staging/rt2870/common/2870_rtmp_init.c    | 33 +++++----
 drivers/staging/rt2870/common/rtusb_io.c      |  3 +-
 drivers/staging/rt2870/rt2870.h               |  6 +-
 5 files changed, 68 insertions(+), 54 deletions(-)

diff --git a/drivers/staging/rt2860/rt_linux.h b/drivers/staging/rt2860/rt_linux.h
index 85175c18243..25b53ac3f82 100644
--- a/drivers/staging/rt2860/rt_linux.h
+++ b/drivers/staging/rt2860/rt_linux.h
@@ -43,9 +43,6 @@
 #include "rtmp_type.h"
 #include <linux/module.h>
 #include <linux/kernel.h>
-#if !defined(RT2860) && !defined(RT30xx)
-#include <linux/kthread.h>
-#endif
 
 #include <linux/spinlock.h>
 #include <linux/init.h>
@@ -166,9 +163,7 @@ typedef int (*HARD_START_XMIT_FUNC)(struct sk_buff *skb, struct net_device *net_
 
 #ifndef RT30xx
 typedef	struct pid *	THREAD_PID;
-#ifdef RT2860
 #define	THREAD_PID_INIT_VALUE	NULL
-#endif
 #define	GET_PID(_v)	find_get_pid(_v)
 #define	GET_PID_NUMBER(_v)	pid_nr(_v)
 #define CHECK_PID_LEGALITY(_pid)	if (pid_nr(_pid) >= 0)
@@ -188,12 +183,12 @@ struct os_cookie {
 	dma_addr_t		  		pAd_pa;
 #endif
 #ifdef RT2870
-	struct usb_device	*pUsb_Dev;
+	struct usb_device		*pUsb_Dev;
 
 #ifndef RT30xx
-	struct task_struct	*MLMEThr_task;
-	struct task_struct	*RTUSBCmdThr_task;
-	struct task_struct	*TimerQThr_task;
+	THREAD_PID				MLMEThr_pid;
+	THREAD_PID				RTUSBCmdThr_pid;
+	THREAD_PID				TimerQThr_pid;
 #endif
 #ifdef RT30xx
 	struct pid	*MLMEThr_pid;
diff --git a/drivers/staging/rt2870/2870_main_dev.c b/drivers/staging/rt2870/2870_main_dev.c
index dd01c64fbf6..a4e8696ca39 100644
--- a/drivers/staging/rt2870/2870_main_dev.c
+++ b/drivers/staging/rt2870/2870_main_dev.c
@@ -235,7 +235,7 @@ INT MlmeThread(
 	DBGPRINT(RT_DEBUG_TRACE,( "<---%s\n",__func__));
 
 #ifndef RT30xx
-	pObj->MLMEThr_task = NULL;
+	pObj->MLMEThr_pid = THREAD_PID_INIT_VALUE;
 #endif
 #ifdef RT30xx
 	pObj->MLMEThr_pid = NULL;
@@ -348,7 +348,7 @@ INT RTUSBCmdThread(
 	DBGPRINT(RT_DEBUG_TRACE,( "<---RTUSBCmdThread\n"));
 
 #ifndef RT30xx
-	pObj->RTUSBCmdThr_task = NULL;
+	pObj->RTUSBCmdThr_pid = THREAD_PID_INIT_VALUE;
 #endif
 #ifdef RT30xx
 	pObj->RTUSBCmdThr_pid = NULL;
@@ -447,7 +447,7 @@ INT TimerQThread(
 	DBGPRINT(RT_DEBUG_TRACE,( "<---%s\n",__func__));
 
 #ifndef RT30xx
-	pObj->TimerQThr_task = NULL;
+	pObj->TimerQThr_pid = THREAD_PID_INIT_VALUE;
 #endif
 #ifdef RT30xx
 	pObj->TimerQThr_pid = NULL;
@@ -883,46 +883,69 @@ VOID RT28xxThreadTerminate(
 
 	// Terminate Threads
 #ifndef RT30xx
-	BUG_ON(pObj->TimerQThr_task == NULL);
-	CHECK_PID_LEGALITY(task_pid(pObj->TimerQThr_task))
+	CHECK_PID_LEGALITY(pObj->TimerQThr_pid)
 	{
 		POS_COOKIE pObj = (POS_COOKIE)pAd->OS_Cookie;
 
-		printk(KERN_DEBUG "Terminate the TimerQThr pid=%d!\n",
-			pid_nr(task_pid(pObj->TimerQThr_task)));
+		printk("Terminate the TimerQThr_pid=%d!\n", GET_PID_NUMBER(pObj->TimerQThr_pid));
 		mb();
 		pAd->TimerFunc_kill = 1;
 		mb();
-		kthread_stop(pObj->TimerQThr_task);
-		pObj->TimerQThr_task = NULL;
+		ret = KILL_THREAD_PID(pObj->TimerQThr_pid, SIGTERM, 1);
+		if (ret)
+		{
+			printk(KERN_WARNING "%s: unable to stop TimerQThread, pid=%d, ret=%d!\n",
+					pAd->net_dev->name, GET_PID_NUMBER(pObj->TimerQThr_pid), ret);
+		}
+		else
+		{
+			wait_for_completion(&pAd->TimerQComplete);
+			pObj->TimerQThr_pid = THREAD_PID_INIT_VALUE;
+		}
 	}
 
-	BUG_ON(pObj->MLMEThr_task == NULL);
-	CHECK_PID_LEGALITY(task_pid(pObj->MLMEThr_task))
+	CHECK_PID_LEGALITY(pObj->MLMEThr_pid)
 	{
-		printk(KERN_DEBUG "Terminate the MLMEThr pid=%d!\n",
-			pid_nr(task_pid(pObj->MLMEThr_task)));
+		printk("Terminate the MLMEThr_pid=%d!\n", GET_PID_NUMBER(pObj->MLMEThr_pid));
 		mb();
 		pAd->mlme_kill = 1;
 		//RT28XX_MLME_HANDLER(pAd);
 		mb();
-		kthread_stop(pObj->MLMEThr_task);
-		pObj->MLMEThr_task = NULL;
+		ret = KILL_THREAD_PID(pObj->MLMEThr_pid, SIGTERM, 1);
+		if (ret)
+		{
+			printk (KERN_WARNING "%s: unable to Mlme thread, pid=%d, ret=%d!\n",
+					pAd->net_dev->name, GET_PID_NUMBER(pObj->MLMEThr_pid), ret);
+		}
+		else
+		{
+			//wait_for_completion (&pAd->notify);
+			wait_for_completion (&pAd->mlmeComplete);
+			pObj->MLMEThr_pid = THREAD_PID_INIT_VALUE;
+		}
 	}
 
-	BUG_ON(pObj->RTUSBCmdThr_task == NULL);
-	CHECK_PID_LEGALITY(task_pid(pObj->RTUSBCmdThr_task))
+	CHECK_PID_LEGALITY(pObj->RTUSBCmdThr_pid)
 	{
-		printk(KERN_DEBUG "Terminate the RTUSBCmdThr pid=%d!\n",
-			pid_nr(task_pid(pObj->RTUSBCmdThr_task)));
+		printk("Terminate the RTUSBCmdThr_pid=%d!\n", GET_PID_NUMBER(pObj->RTUSBCmdThr_pid));
 		mb();
 		NdisAcquireSpinLock(&pAd->CmdQLock);
 		pAd->CmdQ.CmdQState = RT2870_THREAD_STOPED;
 		NdisReleaseSpinLock(&pAd->CmdQLock);
 		mb();
 		//RTUSBCMDUp(pAd);
-		kthread_stop(pObj->RTUSBCmdThr_task);
-		pObj->RTUSBCmdThr_task = NULL;
+		ret = KILL_THREAD_PID(pObj->RTUSBCmdThr_pid, SIGTERM, 1);
+		if (ret)
+		{
+			printk(KERN_WARNING "%s: unable to RTUSBCmd thread, pid=%d, ret=%d!\n",
+					pAd->net_dev->name, GET_PID_NUMBER(pObj->RTUSBCmdThr_pid), ret);
+		}
+		else
+		{
+			//wait_for_completion (&pAd->notify);
+			wait_for_completion (&pAd->CmdQComplete);
+			pObj->RTUSBCmdThr_pid = THREAD_PID_INIT_VALUE;
+		}
 	}
 #endif
 #ifdef RT30xx
@@ -1045,7 +1068,7 @@ BOOLEAN RT28XXChipsetCheck(
 			dev_p->descriptor.idProduct == rtusb_usb_id[i].idProduct)
 		{
 #ifndef RT30xx
-			printk(KERN_DEBUG "rt2870: idVendor = 0x%x, idProduct = 0x%x\n",
+			printk("rt2870: idVendor = 0x%x, idProduct = 0x%x\n",
 #endif
 #ifdef RT30xx
 			printk("rt2870: idVendor = 0x%x, idProduct = 0x%x\n",
diff --git a/drivers/staging/rt2870/common/2870_rtmp_init.c b/drivers/staging/rt2870/common/2870_rtmp_init.c
index 0f4c8af97e4..80909e9ab5a 100644
--- a/drivers/staging/rt2870/common/2870_rtmp_init.c
+++ b/drivers/staging/rt2870/common/2870_rtmp_init.c
@@ -700,8 +700,8 @@ NDIS_STATUS AdapterBlockAllocateMemory(
 	usb_dev = pObj->pUsb_Dev;
 
 #ifndef RT30xx
-	pObj->MLMEThr_task		= NULL;
-	pObj->RTUSBCmdThr_task	= NULL;
+	pObj->MLMEThr_pid		= THREAD_PID_INIT_VALUE;
+	pObj->RTUSBCmdThr_pid	= THREAD_PID_INIT_VALUE;
 #endif
 #ifdef RT30xx
 	pObj->MLMEThr_pid	= NULL;
@@ -743,7 +743,7 @@ NDIS_STATUS	 CreateThreads(
 	PRTMP_ADAPTER pAd = net_dev->ml_priv;
 	POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie;
 #ifndef RT30xx
-	struct task_struct *tsk;
+	pid_t pid_number = -1;
 #endif
 #ifdef RT30xx
 	pid_t pid_number;
@@ -762,10 +762,10 @@ NDIS_STATUS	 CreateThreads(
 
 	// Creat MLME Thread
 #ifndef RT30xx
-	pObj->MLMEThr_task = NULL;
-	tsk = kthread_run(MlmeThread, pAd, "%s", pAd->net_dev->name);
-
-	if (IS_ERR(tsk)) {
+	pObj->MLMEThr_pid= THREAD_PID_INIT_VALUE;
+	pid_number = kernel_thread(MlmeThread, pAd, CLONE_VM);
+	if (pid_number < 0)
+	{
 #endif
 #ifdef RT30xx
 	pObj->MLMEThr_pid = NULL;
@@ -778,7 +778,7 @@ NDIS_STATUS	 CreateThreads(
 	}
 
 #ifndef RT30xx
-	pObj->MLMEThr_task = tsk;
+	pObj->MLMEThr_pid = GET_PID(pid_number);
 #endif
 #ifdef RT30xx
 	pObj->MLMEThr_pid = find_get_pid(pid_number);
@@ -788,10 +788,9 @@ NDIS_STATUS	 CreateThreads(
 
 	// Creat Command Thread
 #ifndef RT30xx
-	pObj->RTUSBCmdThr_task = NULL;
-	tsk = kthread_run(RTUSBCmdThread, pAd, "%s", pAd->net_dev->name);
-
-	if (IS_ERR(tsk) < 0)
+	pObj->RTUSBCmdThr_pid= THREAD_PID_INIT_VALUE;
+	pid_number = kernel_thread(RTUSBCmdThread, pAd, CLONE_VM);
+	if (pid_number < 0)
 #endif
 #ifdef RT30xx
 	pObj->RTUSBCmdThr_pid = NULL;
@@ -804,7 +803,7 @@ NDIS_STATUS	 CreateThreads(
 	}
 
 #ifndef RT30xx
-	pObj->RTUSBCmdThr_task = tsk;
+	pObj->RTUSBCmdThr_pid = GET_PID(pid_number);
 #endif
 #ifdef RT30xx
 	pObj->RTUSBCmdThr_pid = find_get_pid(pid_number);
@@ -812,9 +811,9 @@ NDIS_STATUS	 CreateThreads(
 	wait_for_completion(&(pAd->CmdQComplete));
 
 #ifndef RT30xx
-	pObj->TimerQThr_task = NULL;
-	tsk = kthread_run(TimerQThread, pAd, "%s", pAd->net_dev->name);
-	if (IS_ERR(tsk) < 0)
+	pObj->TimerQThr_pid= THREAD_PID_INIT_VALUE;
+	pid_number = kernel_thread(TimerQThread, pAd, CLONE_VM);
+	if (pid_number < 0)
 #endif
 #ifdef RT30xx
 	pObj->TimerQThr_pid = NULL;
@@ -826,7 +825,7 @@ NDIS_STATUS	 CreateThreads(
 		return NDIS_STATUS_FAILURE;
 	}
 #ifndef RT30xx
-	pObj->TimerQThr_task = tsk;
+	pObj->TimerQThr_pid = GET_PID(pid_number);
 #endif
 #ifdef RT30xx
 	pObj->TimerQThr_pid = find_get_pid(pid_number);
diff --git a/drivers/staging/rt2870/common/rtusb_io.c b/drivers/staging/rt2870/common/rtusb_io.c
index fd1b0c18f2a..704b5c2d509 100644
--- a/drivers/staging/rt2870/common/rtusb_io.c
+++ b/drivers/staging/rt2870/common/rtusb_io.c
@@ -984,8 +984,7 @@ NDIS_STATUS	RTUSBEnqueueCmdFromNdis(
 	POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie;
 
 #ifndef RT30xx
-	BUG_ON(pObj->RTUSBCmdThr_task == NULL);
-	CHECK_PID_LEGALITY(task_pid(pObj->RTUSBCmdThr_task))
+	CHECK_PID_LEGALITY(pObj->RTUSBCmdThr_pid)
 #endif
 #ifdef RT30xx
 	if (pObj->RTUSBCmdThr_pid < 0)
diff --git a/drivers/staging/rt2870/rt2870.h b/drivers/staging/rt2870/rt2870.h
index 10e1640d61e..2b8872b2fd9 100644
--- a/drivers/staging/rt2870/rt2870.h
+++ b/drivers/staging/rt2870/rt2870.h
@@ -590,16 +590,14 @@ VOID RTUSBBulkRxComplete(purbb_t pUrb, struct pt_regs *pt_regs);
 #define RTUSBMlmeUp(pAd)	        \
 {								    \
 	POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie;	\
-	BUG_ON(pObj->MLMEThr_task == NULL);		    \
-	CHECK_PID_LEGALITY(task_pid(pObj->MLMEThr_task))		    \
+	CHECK_PID_LEGALITY(pObj->MLMEThr_pid)		    \
         up(&(pAd->mlme_semaphore)); \
 }
 
 #define RTUSBCMDUp(pAd)	                \
 {									    \
 	POS_COOKIE pObj = (POS_COOKIE) pAd->OS_Cookie;	\
-	BUG_ON(pObj->RTUSBCmdThr_task == NULL);	    \
-	CHECK_PID_LEGALITY(task_pid(pObj->RTUSBCmdThr_task))	    \
+	CHECK_PID_LEGALITY(pObj->RTUSBCmdThr_pid)	    \
 	    up(&(pAd->RTUSBCmd_semaphore)); \
 }
 #endif
-- 
GitLab


From ce9c010c5c39df05ed81a06aba492c45ee0c6f19 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Tue, 4 Aug 2009 16:53:36 -0700
Subject: [PATCH 0668/1153] Staging: rtl8192su: fix build error

This fixes a build error when selecting the rtl8192su driver as a
module.  This has been reported by me, and the opensuse kernel developer
team, and I finally tracked it down.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/staging/rtl8192su/ieee80211.h              | 2 +-
 drivers/staging/rtl8192su/ieee80211/ieee80211.h    | 2 +-
 drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c | 3 ++-
 drivers/staging/rtl8192su/r8192U_core.c            | 2 +-
 4 files changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/staging/rtl8192su/ieee80211.h b/drivers/staging/rtl8192su/ieee80211.h
index 0edb09a536f..ea973931803 100644
--- a/drivers/staging/rtl8192su/ieee80211.h
+++ b/drivers/staging/rtl8192su/ieee80211.h
@@ -2645,7 +2645,7 @@ extern int ieee80211_encrypt_fragment(
 	struct sk_buff *frag,
 	int hdr_len);
 
-extern int ieee80211_xmit(struct sk_buff *skb,
+extern int rtl8192_ieee80211_xmit(struct sk_buff *skb,
 			  struct net_device *dev);
 extern void ieee80211_txb_free(struct ieee80211_txb *);
 
diff --git a/drivers/staging/rtl8192su/ieee80211/ieee80211.h b/drivers/staging/rtl8192su/ieee80211/ieee80211.h
index 720bfcbfadc..5e3a2cbed2b 100644
--- a/drivers/staging/rtl8192su/ieee80211/ieee80211.h
+++ b/drivers/staging/rtl8192su/ieee80211/ieee80211.h
@@ -2645,7 +2645,7 @@ extern int ieee80211_encrypt_fragment(
 	struct sk_buff *frag,
 	int hdr_len);
 
-extern int ieee80211_xmit(struct sk_buff *skb,
+extern int rtl8192_ieee80211_xmit(struct sk_buff *skb,
 			  struct net_device *dev);
 extern void ieee80211_txb_free(struct ieee80211_txb *);
 
diff --git a/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c b/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c
index 7294572b990..cba12b84be5 100644
--- a/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c
+++ b/drivers/staging/rtl8192su/ieee80211/ieee80211_tx.c
@@ -618,7 +618,7 @@ void ieee80211_query_seqnum(struct ieee80211_device*ieee, struct sk_buff* skb, u
 	}
 }
 
-int ieee80211_xmit(struct sk_buff *skb, struct net_device *dev)
+int rtl8192_ieee80211_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 #if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,5,0))
 	struct ieee80211_device *ieee = netdev_priv(dev);
@@ -943,5 +943,6 @@ int ieee80211_xmit(struct sk_buff *skb, struct net_device *dev)
 	return 1;
 
 }
+EXPORT_SYMBOL(rtl8192_ieee80211_xmit);
 
 EXPORT_SYMBOL(ieee80211_txb_free);
diff --git a/drivers/staging/rtl8192su/r8192U_core.c b/drivers/staging/rtl8192su/r8192U_core.c
index 4ab250743e8..70f81a8f129 100644
--- a/drivers/staging/rtl8192su/r8192U_core.c
+++ b/drivers/staging/rtl8192su/r8192U_core.c
@@ -12142,7 +12142,7 @@ static const struct net_device_ops rtl8192_netdev_ops = {
 	.ndo_set_mac_address	= r8192_set_mac_adr,
 	.ndo_validate_addr	= eth_validate_addr,
 	.ndo_change_mtu		= eth_change_mtu,
-	.ndo_start_xmit		= ieee80211_xmit,
+	.ndo_start_xmit		= rtl8192_ieee80211_xmit,
 };
 
 #if LINUX_VERSION_CODE > KERNEL_VERSION(2,5,0)
-- 
GitLab


From 5fb4d2525b6dcffbb8bc26a7dfc7ed17ad323a06 Mon Sep 17 00:00:00 2001
From: Jeff Mahoney <jeffm@suse.com>
Date: Fri, 7 Aug 2009 16:12:03 -0700
Subject: [PATCH 0669/1153] staging: add dependencies on PCI for drivers that
 require it

This patch adds PCI dependencies to staging drivers that require it.

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/staging/b3dfg/Kconfig | 1 +
 drivers/staging/heci/Kconfig  | 1 +
 2 files changed, 2 insertions(+)

diff --git a/drivers/staging/b3dfg/Kconfig b/drivers/staging/b3dfg/Kconfig
index 524231047de..9e6573cf97d 100644
--- a/drivers/staging/b3dfg/Kconfig
+++ b/drivers/staging/b3dfg/Kconfig
@@ -1,5 +1,6 @@
 config B3DFG
        tristate "Brontes 3d Frame Framegrabber"
+       depends on PCI
        default n
        ---help---
          This driver provides support for the Brontes 3d Framegrabber
diff --git a/drivers/staging/heci/Kconfig b/drivers/staging/heci/Kconfig
index ae8d588d3a2..c7206f8bcd9 100644
--- a/drivers/staging/heci/Kconfig
+++ b/drivers/staging/heci/Kconfig
@@ -1,5 +1,6 @@
 config HECI
 	tristate "Intel Management Engine Interface (MEI) Support"
+	depends on PCI
 	---help---
 	  The Intel Management Engine Interface (Intel MEI) driver allows
 	  applications to access the Active Management Technology
-- 
GitLab


From 749d00dbf154fc2f9ac59df669205039de0d5b45 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Fri, 7 Aug 2009 21:00:10 +0200
Subject: [PATCH 0670/1153] Staging: rspiusb: Fix buffer overflow

usb_buffer_map_sg() may return -1. This will result in a read from
pdx->PixelUrb[frameInfo][-1]

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/staging/rspiusb/rspiusb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/staging/rspiusb/rspiusb.c b/drivers/staging/rspiusb/rspiusb.c
index 2f8155c1968..04e2f92c0f6 100644
--- a/drivers/staging/rspiusb/rspiusb.c
+++ b/drivers/staging/rspiusb/rspiusb.c
@@ -716,6 +716,8 @@ static int MapUserBuffer(struct ioctl_struct *io, struct device_extension *pdx)
 		pdx->PixelUrb[frameInfo][i]->transfer_flags =
 		    URB_NO_TRANSFER_DMA_MAP | URB_NO_INTERRUPT;
 	}
+	if (i == 0)
+		return -EINVAL;
 	/* only interrupt when last URB completes */
 	pdx->PixelUrb[frameInfo][--i]->transfer_flags &= ~URB_NO_INTERRUPT;
 	pdx->pendedPixelUrbs[frameInfo] =
-- 
GitLab


From 087d7e56deffb611a098e7e257388a41edbeef1f Mon Sep 17 00:00:00 2001
From: Yinghai Lu <yinghai@kernel.org>
Date: Tue, 4 Aug 2009 08:59:59 -0700
Subject: [PATCH 0671/1153] x86: Fix MSI-X initialization by using online_mask
 for x2apic target_cpus

found a system where x2apic reports an MSI-X irq initialization
failure:

[  302.859446] igbvf 0000:81:10.4: enabling device (0000 -> 0002)
[  302.874369] igbvf 0000:81:10.4: using 64bit DMA mask
[  302.879023] igbvf 0000:81:10.4: using 64bit consistent DMA mask
[  302.894386] igbvf 0000:81:10.4: enabling bus mastering
[  302.898171] igbvf 0000:81:10.4: setting latency timer to 64
[  302.914050] reserve_memtype added 0xefb08000-0xefb0c000, track uncached-minus, req uncached-minus, ret uncached-minus
[  302.933839] reserve_memtype added 0xefb28000-0xefb29000, track uncached-minus, req uncached-minus, ret uncached-minus
[  302.940367]   alloc irq_desc for 265 on node 4
[  302.956874]   alloc kstat_irqs on node 4
[  302.959452] alloc irq_2_iommu on node 0
[  302.974328] igbvf 0000:81:10.4: irq 265 for MSI/MSI-X
[  302.977778]   alloc irq_desc for 266 on node 4
[  302.980347]   alloc kstat_irqs on node 4
[  302.995312] free_memtype request 0xefb28000-0xefb29000
[  302.998816] igbvf 0000:81:10.4: Failed to initialize MSI-X interrupts.

... it turns out that when trying to enable MSI-X,
__assign_irq_vector(new, cfg_new, apic->target_cpus()) can not
get vector because for x2apic target-cpus returns cpumask_of(0)

Update that to online_mask like xapic.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4A785AFF.3050902@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/apic/x2apic_cluster.c | 8 +++++---
 arch/x86/kernel/apic/x2apic_phys.c    | 8 +++++---
 2 files changed, 10 insertions(+), 6 deletions(-)

diff --git a/arch/x86/kernel/apic/x2apic_cluster.c b/arch/x86/kernel/apic/x2apic_cluster.c
index 2ed4e2bb3b3..a5371ec3677 100644
--- a/arch/x86/kernel/apic/x2apic_cluster.c
+++ b/arch/x86/kernel/apic/x2apic_cluster.c
@@ -17,11 +17,13 @@ static int x2apic_acpi_madt_oem_check(char *oem_id, char *oem_table_id)
 	return x2apic_enabled();
 }
 
-/* Start with all IRQs pointing to boot CPU.  IRQ balancing will shift them. */
-
+/*
+ * need to use more than cpu 0, because we need more vectors when
+ * MSI-X are used.
+ */
 static const struct cpumask *x2apic_target_cpus(void)
 {
-	return cpumask_of(0);
+	return cpu_online_mask;
 }
 
 /*
diff --git a/arch/x86/kernel/apic/x2apic_phys.c b/arch/x86/kernel/apic/x2apic_phys.c
index 0b631c6a2e0..a8989aadc99 100644
--- a/arch/x86/kernel/apic/x2apic_phys.c
+++ b/arch/x86/kernel/apic/x2apic_phys.c
@@ -27,11 +27,13 @@ static int x2apic_acpi_madt_oem_check(char *oem_id, char *oem_table_id)
 		return 0;
 }
 
-/* Start with all IRQs pointing to boot CPU.  IRQ balancing will shift them. */
-
+/*
+ * need to use more than cpu 0, because we need more vectors when
+ * MSI-X are used.
+ */
 static const struct cpumask *x2apic_target_cpus(void)
 {
-	return cpumask_of(0);
+	return cpu_online_mask;
 }
 
 static void x2apic_vector_allocation_domain(int cpu, struct cpumask *retmask)
-- 
GitLab


From ad7d6c7a0654a4bbda3e109f56af713267e96274 Mon Sep 17 00:00:00 2001
From: Yinghai Lu <yinghai@kernel.org>
Date: Tue, 4 Aug 2009 09:01:33 -0700
Subject: [PATCH 0672/1153] x86/irq: Fix move_irq_desc() for nodes without ram

Don't move it if target node is -1.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4A785B5D.4070702@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/irq/numa_migrate.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/kernel/irq/numa_migrate.c b/kernel/irq/numa_migrate.c
index 2f69bee57bf..3fd30197da2 100644
--- a/kernel/irq/numa_migrate.c
+++ b/kernel/irq/numa_migrate.c
@@ -107,8 +107,8 @@ out_unlock:
 
 struct irq_desc *move_irq_desc(struct irq_desc *desc, int node)
 {
-	/* those all static, do move them */
-	if (desc->irq < NR_IRQS_LEGACY)
+	/* those static or target node is -1, do not move them */
+	if (desc->irq < NR_IRQS_LEGACY || node == -1)
 		return desc;
 
 	if (desc->node != node)
-- 
GitLab


From 498cdbfbcf98e0d2c90a26e6a02a82f043876e48 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Ozan=20=C3=87a=C4=9Flayan?= <ozan@pardus.org.tr>
Date: Tue, 4 Aug 2009 19:39:31 +0300
Subject: [PATCH 0673/1153] x86: Add quirk to make Apple MacBookPro5,1 use
 reboot=pci
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

MacBookPro5,1 is not able to reboot unless reboot=pci is set.
This patch forces it through a DMI quirk specific to this
device.

Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <1249403971-6543-1-git-send-email-ozan@pardus.org.tr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/reboot.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/arch/x86/kernel/reboot.c b/arch/x86/kernel/reboot.c
index 834c9da8bf9..9eb89760370 100644
--- a/arch/x86/kernel/reboot.c
+++ b/arch/x86/kernel/reboot.c
@@ -405,7 +405,7 @@ EXPORT_SYMBOL(machine_real_restart);
 #endif /* CONFIG_X86_32 */
 
 /*
- * Apple MacBook5,2 (2009 MacBook) needs reboot=p
+ * Some Apple MacBook and MacBookPro's needs reboot=p to be able to reboot
  */
 static int __init set_pci_reboot(const struct dmi_system_id *d)
 {
@@ -426,6 +426,14 @@ static struct dmi_system_id __initdata pci_reboot_dmi_table[] = {
 			DMI_MATCH(DMI_PRODUCT_NAME, "MacBook5,2"),
 		},
 	},
+	{	/* Handle problems with rebooting on Apple MacBookPro5,1 */
+		.callback = set_pci_reboot,
+		.ident = "Apple MacBookPro5,1",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro5,1"),
+		},
+	},
 	{ }
 };
 
-- 
GitLab


From 96b2de313b1e0e02aea80ee47df6a2b5cbdf8e13 Mon Sep 17 00:00:00 2001
From: Tom Zanussi <tzanussi@gmail.com>
Date: Sat, 8 Aug 2009 10:49:09 -0500
Subject: [PATCH 0674/1153] tracing/filters: Don't use pred on alloc failure

Dan Carpenter sent me a fix to prevent pred from being used if
it couldn't be allocated.  I noticed the same problem also
existed for the create_pred() case and added a fix for that.

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <1249746549.6453.29.camel@tropicana>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/trace/trace_events_filter.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/kernel/trace/trace_events_filter.c b/kernel/trace/trace_events_filter.c
index 936c621bbf4..1557148be34 100644
--- a/kernel/trace/trace_events_filter.c
+++ b/kernel/trace/trace_events_filter.c
@@ -1029,6 +1029,8 @@ static int replace_preds(struct event_subsystem *system,
 
 		if (elt->op == OP_AND || elt->op == OP_OR) {
 			pred = create_logical_pred(elt->op);
+			if (!pred)
+				return -ENOMEM;
 			if (call) {
 				err = filter_add_pred(ps, call, pred);
 				filter_free_pred(pred);
@@ -1048,6 +1050,8 @@ static int replace_preds(struct event_subsystem *system,
 		}
 
 		pred = create_pred(elt->op, operand1, operand2);
+		if (!pred)
+			return -ENOMEM;
 		if (call) {
 			err = filter_add_pred(ps, call, pred);
 			filter_free_pred(pred);
-- 
GitLab


From 26528e773ecc74fb1b61b7275f86f761cbb340ec Mon Sep 17 00:00:00 2001
From: Tom Zanussi <tzanussi@gmail.com>
Date: Sat, 8 Aug 2009 10:49:53 -0500
Subject: [PATCH 0675/1153] tracing/filters: Always free pred on
 filter_add_subsystem_pred() failure

If filter_add_subsystem_pred() fails due to ENOSPC or ENOMEM,
the pred doesn't get freed, while as a side effect it does for
other errors. Make it so the caller always frees the pred for
any error.

Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <1249746593.6453.32.camel@tropicana>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/trace/trace_events_filter.c | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)

diff --git a/kernel/trace/trace_events_filter.c b/kernel/trace/trace_events_filter.c
index 1557148be34..f32dc9d1ea7 100644
--- a/kernel/trace/trace_events_filter.c
+++ b/kernel/trace/trace_events_filter.c
@@ -624,9 +624,6 @@ static int filter_add_subsystem_pred(struct filter_parse_state *ps,
 		return -ENOSPC;
 	}
 
-	filter->preds[filter->n_preds] = pred;
-	filter->n_preds++;
-
 	list_for_each_entry(call, &ftrace_events, list) {
 
 		if (!call->define_fields)
@@ -643,6 +640,9 @@ static int filter_add_subsystem_pred(struct filter_parse_state *ps,
 		}
 		replace_filter_string(call->filter, filter_string);
 	}
+
+	filter->preds[filter->n_preds] = pred;
+	filter->n_preds++;
 out:
 	return err;
 }
@@ -1034,9 +1034,12 @@ static int replace_preds(struct event_subsystem *system,
 			if (call) {
 				err = filter_add_pred(ps, call, pred);
 				filter_free_pred(pred);
-			} else
+			} else {
 				err = filter_add_subsystem_pred(ps, system,
 							pred, filter_string);
+				if (err)
+					filter_free_pred(pred);
+			}
 			if (err)
 				return err;
 
@@ -1055,9 +1058,12 @@ static int replace_preds(struct event_subsystem *system,
 		if (call) {
 			err = filter_add_pred(ps, call, pred);
 			filter_free_pred(pred);
-		} else
+		} else {
 			err = filter_add_subsystem_pred(ps, system, pred,
 							filter_string);
+			if (err)
+				filter_free_pred(pred);
+		}
 		if (err)
 			return err;
 
-- 
GitLab


From 17d42c1c497aa54952b9e58c1502a46f0df40315 Mon Sep 17 00:00:00 2001
From: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Thu, 6 Aug 2009 16:03:30 -0700
Subject: [PATCH 0676/1153] posix_cpu_timers_exit_group(): Do not use
 thread_group_cputimer()

When the process exits we don't have to run new cputimer nor
use running one (as it not accounts when tsk->exit_state != 0)
to get process CPU times.  As there is only one thread we can
just use CPU times fields from task and signal structs.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Roland McGrath <roland@redhat.com>
Cc: Vitaly Mayatskikh <vmayatsk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/posix-cpu-timers.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/kernel/posix-cpu-timers.c b/kernel/posix-cpu-timers.c
index bece7c0b67b..e33a21cb940 100644
--- a/kernel/posix-cpu-timers.c
+++ b/kernel/posix-cpu-timers.c
@@ -521,11 +521,12 @@ void posix_cpu_timers_exit(struct task_struct *tsk)
 }
 void posix_cpu_timers_exit_group(struct task_struct *tsk)
 {
-	struct task_cputime cputime;
+	struct signal_struct *const sig = tsk->signal;
 
-	thread_group_cputimer(tsk, &cputime);
 	cleanup_timers(tsk->signal->cpu_timers,
-		       cputime.utime, cputime.stime, cputime.sum_exec_runtime);
+		       cputime_add(tsk->utime, sig->utime),
+		       cputime_add(tsk->stime, sig->stime),
+		       tsk->se.sum_exec_runtime + sig->sum_sched_runtime);
 }
 
 static void clear_dead_task(struct k_itimer *timer, union cpu_time_count now)
-- 
GitLab


From 38d5487db7f289be1d56ac7df704ee49ed3213b9 Mon Sep 17 00:00:00 2001
From: Keith Packard <keithp@keithp.com>
Date: Mon, 20 Jul 2009 14:49:17 -0700
Subject: [PATCH 0677/1153] drm: When adding probed modes, preserve duplicate
 mode types

The code which takes probed modes and adds them to a connector eliminates
duplicate modes by comparing them using drm_mode_equal. That function
doesn't consider the type bits, which means that any modes which differ only
in the type field will be lost.

One of the bits in the mode->type field is the DRM_MODE_TYPE_PREFERRED bit.
If the mode with that bit is lost, then higher level code will not know
which mode to select, causing a random mode to be used instead.

This patch simply merges the two mode type bits together; that seems
reasonable to me, but perhaps only a subset of the bits should be used? None
of these can be user defined as they all come from looking at just the
hardware.

Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/drm_modes.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/gpu/drm/drm_modes.c b/drivers/gpu/drm/drm_modes.c
index 54f492a488a..7914097b09c 100644
--- a/drivers/gpu/drm/drm_modes.c
+++ b/drivers/gpu/drm/drm_modes.c
@@ -566,6 +566,8 @@ void drm_mode_connector_list_update(struct drm_connector *connector)
 				found_it = 1;
 				/* if equal delete the probed mode */
 				mode->status = pmode->status;
+				/* Merge type bits together */
+				mode->type |= pmode->type;
 				list_del(&pmode->head);
 				drm_mode_destroy(connector->dev, pmode);
 				break;
-- 
GitLab


From 8d3457ec3198a569dd14dc9e3ae8b6163bcaa0b5 Mon Sep 17 00:00:00 2001
From: Paul Rolland <rol@as2917.net>
Date: Sun, 9 Aug 2009 12:24:01 +1000
Subject: [PATCH 0678/1153] drm: silence pointless vblank warning.

Some applications/hardware combinations are triggering the message "failed to
acquire vblank counter" to be issued up to 20 times a second, which makes it
both useless and dangerous, as this may hide other important messages.
This changes makes it only appear when people are debugging.

Signed-off-by: Paul Rolland <rol@as2917.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Lost-twice-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/drm_irq.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/drm_irq.c b/drivers/gpu/drm/drm_irq.c
index b4a3dbcebe9..f85aaf21e78 100644
--- a/drivers/gpu/drm/drm_irq.c
+++ b/drivers/gpu/drm/drm_irq.c
@@ -566,7 +566,7 @@ int drm_wait_vblank(struct drm_device *dev, void *data,
 
 	ret = drm_vblank_get(dev, crtc);
 	if (ret) {
-		DRM_ERROR("failed to acquire vblank counter, %d\n", ret);
+		DRM_DEBUG("failed to acquire vblank counter, %d\n", ret);
 		return ret;
 	}
 	seq = drm_vblank_count(dev, crtc);
-- 
GitLab


From 6cb504c29b1338925c83e4430e42a51eaa43781e Mon Sep 17 00:00:00 2001
From: Frans Pop <elendil@planet.nl>
Date: Sun, 9 Aug 2009 12:25:29 +1000
Subject: [PATCH 0679/1153] drm/i915: silence vblank warnings

these errors are pretty pointless

Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/i915/i915_irq.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index 83aee80e77a..7ebc84c2881 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -190,7 +190,7 @@ u32 i915_get_vblank_counter(struct drm_device *dev, int pipe)
 	low_frame = pipe ? PIPEBFRAMEPIXEL : PIPEAFRAMEPIXEL;
 
 	if (!i915_pipe_enabled(dev, pipe)) {
-		DRM_ERROR("trying to get vblank count for disabled pipe %d\n", pipe);
+		DRM_DEBUG("trying to get vblank count for disabled pipe %d\n", pipe);
 		return 0;
 	}
 
@@ -219,7 +219,7 @@ u32 gm45_get_vblank_counter(struct drm_device *dev, int pipe)
 	int reg = pipe ? PIPEB_FRMCOUNT_GM45 : PIPEA_FRMCOUNT_GM45;
 
 	if (!i915_pipe_enabled(dev, pipe)) {
-		DRM_ERROR("trying to get vblank count for disabled pipe %d\n", pipe);
+		DRM_DEBUG("trying to get vblank count for disabled pipe %d\n", pipe);
 		return 0;
 	}
 
-- 
GitLab


From fdb8a42742ac95606668f73481dfb2f760658fdd Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Thu, 6 Aug 2009 15:58:13 -0700
Subject: [PATCH 0680/1153] x86: fix buffer overflow in efi_init()

If the vendor name (from c16) can be longer than 100 bytes (or missing a
terminating null), then the null is written past the end of vendor[].

Found with Parfait, http://research.sun.com/projects/parfait/

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Ying <ying.huang@intel.com>
---
 arch/x86/kernel/efi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/kernel/efi.c b/arch/x86/kernel/efi.c
index 19ccf6d0dcc..fe26ba3e345 100644
--- a/arch/x86/kernel/efi.c
+++ b/arch/x86/kernel/efi.c
@@ -354,7 +354,7 @@ void __init efi_init(void)
 	 */
 	c16 = tmp = early_ioremap(efi.systab->fw_vendor, 2);
 	if (c16) {
-		for (i = 0; i < sizeof(vendor) && *c16; ++i)
+		for (i = 0; i < sizeof(vendor) - 1 && *c16; ++i)
 			vendor[i] = *c16++;
 		vendor[i] = '\0';
 	} else
-- 
GitLab


From b4a2f5e723e4f7df46731106faf9e2405673c073 Mon Sep 17 00:00:00 2001
From: Gleb Natapov <gleb@redhat.com>
Date: Sun, 5 Jul 2009 18:48:11 +0300
Subject: [PATCH 0681/1153] KVM: Avoid redelivery of edge interrupt before next
 edge

The check for an edge is broken in current ioapic code. ioapic->irr is
cleared on each edge interrupt by ioapic_service() and this makes
old_irr != ioapic->irr condition in kvm_ioapic_set_irq() to be always
true. The patch fixes the code to properly recognise edge.

Some HW emulation calls set_irq() without level change. If each such
call is propagated to an OS it may confuse a device driver. This is the
case with keyboard device emulation and Windows XP x64  installer on SMP VM.
Each keystroke produce two interrupts (down/up) one interrupt is
submitted to CPU0 and another to CPU1. This confuses Windows somehow
and it ignores keystrokes.

Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
---
 virt/kvm/ioapic.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/virt/kvm/ioapic.c b/virt/kvm/ioapic.c
index 1eddae94bab..1150c6d5c7b 100644
--- a/virt/kvm/ioapic.c
+++ b/virt/kvm/ioapic.c
@@ -95,8 +95,6 @@ static int ioapic_service(struct kvm_ioapic *ioapic, unsigned int idx)
 		if (injected && pent->fields.trig_mode == IOAPIC_LEVEL_TRIG)
 			pent->fields.remote_irr = 1;
 	}
-	if (!pent->fields.trig_mode)
-		ioapic->irr &= ~(1 << idx);
 
 	return injected;
 }
@@ -136,7 +134,8 @@ static void ioapic_write_indirect(struct kvm_ioapic *ioapic, u32 val)
 		mask_after = ioapic->redirtbl[index].fields.mask;
 		if (mask_before != mask_after)
 			kvm_fire_mask_notifiers(ioapic->kvm, index, mask_after);
-		if (ioapic->irr & (1 << index))
+		if (ioapic->redirtbl[index].fields.trig_mode == IOAPIC_LEVEL_TRIG
+		    && ioapic->irr & (1 << index))
 			ioapic_service(ioapic, index);
 		break;
 	}
@@ -184,9 +183,10 @@ int kvm_ioapic_set_irq(struct kvm_ioapic *ioapic, int irq, int level)
 		if (!level)
 			ioapic->irr &= ~mask;
 		else {
+			int edge = (entry.fields.trig_mode == IOAPIC_EDGE_TRIG);
 			ioapic->irr |= mask;
-			if ((!entry.fields.trig_mode && old_irr != ioapic->irr)
-			    || !entry.fields.remote_irr)
+			if ((edge && old_irr != ioapic->irr) ||
+			    (!edge && !entry.fields.remote_irr))
 				ret = ioapic_service(ioapic, irq);
 		}
 	}
-- 
GitLab


From 3a6593050fbd8bbcaed3a44d01c31d907315c86c Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Tue, 21 Jul 2009 17:34:57 +0200
Subject: [PATCH 0682/1153] perf_counter, ftrace: Fix perf_counter integration

Adds possible second part to the assign argument of TP_EVENT().

  TP_perf_assign(
	__perf_count(foo);
	__perf_addr(bar);
  )

Which, when specified make the swcounter increment with @foo instead
of the usual 1, and report @bar for PERF_SAMPLE_ADDR (data address
associated with the event) when this triggers a counter overflow.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 include/trace/ftrace.h | 110 +++++++++++++++++++++++++++++++----------
 kernel/perf_counter.c  |   6 +--
 2 files changed, 88 insertions(+), 28 deletions(-)

diff --git a/include/trace/ftrace.h b/include/trace/ftrace.h
index 1867553c61e..fec71f8dbc4 100644
--- a/include/trace/ftrace.h
+++ b/include/trace/ftrace.h
@@ -144,6 +144,9 @@
 #undef TP_fast_assign
 #define TP_fast_assign(args...) args
 
+#undef TP_perf_assign
+#define TP_perf_assign(args...)
+
 #undef TRACE_EVENT
 #define TRACE_EVENT(call, proto, args, tstruct, func, print)		\
 static int								\
@@ -345,6 +348,88 @@ static inline int ftrace_get_offsets_##call(				\
 
 #include TRACE_INCLUDE(TRACE_INCLUDE_FILE)
 
+#ifdef CONFIG_EVENT_PROFILE
+
+/*
+ * Generate the functions needed for tracepoint perf_counter support.
+ *
+ * static void ftrace_profile_<call>(proto)
+ * {
+ * 	extern void perf_tpcounter_event(int, u64, u64);
+ * 	u64 __addr = 0, __count = 1;
+ *
+ * 	<assign>   <-- here we expand the TP_perf_assign() macro
+ *
+ * 	perf_tpcounter_event(event_<call>.id, __addr, __count);
+ * }
+ *
+ * static int ftrace_profile_enable_<call>(struct ftrace_event_call *event_call)
+ * {
+ * 	int ret = 0;
+ *
+ * 	if (!atomic_inc_return(&event_call->profile_count))
+ * 		ret = register_trace_<call>(ftrace_profile_<call>);
+ *
+ * 	return ret;
+ * }
+ *
+ * static void ftrace_profile_disable_<call>(struct ftrace_event_call *event_call)
+ * {
+ * 	if (atomic_add_negative(-1, &event->call->profile_count))
+ * 		unregister_trace_<call>(ftrace_profile_<call>);
+ * }
+ *
+ */
+
+#undef TP_fast_assign
+#define TP_fast_assign(args...)
+
+#undef TP_perf_assign
+#define TP_perf_assign(args...) args
+
+#undef __perf_addr
+#define __perf_addr(a) __addr = (a)
+
+#undef __perf_count
+#define __perf_count(c) __count = (c)
+
+#undef TRACE_EVENT
+#define TRACE_EVENT(call, proto, args, tstruct, assign, print)		\
+									\
+static void ftrace_profile_##call(proto)				\
+{									\
+	extern void perf_tpcounter_event(int, u64, u64);		\
+	u64 __addr = 0, __count = 1;					\
+	{ assign; }							\
+	perf_tpcounter_event(event_##call.id, __addr, __count);		\
+}									\
+									\
+static int ftrace_profile_enable_##call(struct ftrace_event_call *event_call) \
+{									\
+	int ret = 0;							\
+									\
+	if (!atomic_inc_return(&event_call->profile_count))		\
+		ret = register_trace_##call(ftrace_profile_##call);	\
+									\
+	return ret;							\
+}									\
+									\
+static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\
+{									\
+	if (atomic_add_negative(-1, &event_call->profile_count))	\
+		unregister_trace_##call(ftrace_profile_##call);		\
+}
+
+#include TRACE_INCLUDE(TRACE_INCLUDE_FILE)
+
+#undef TP_fast_assign
+#define TP_fast_assign(args...) args
+
+#undef TP_perf_assign
+#define TP_perf_assign(args...)
+
+#endif
+
 /*
  * Stage 4 of the trace events.
  *
@@ -447,28 +532,6 @@ static inline int ftrace_get_offsets_##call(				\
 #define TP_FMT(fmt, args...)	fmt "\n", ##args
 
 #ifdef CONFIG_EVENT_PROFILE
-#define _TRACE_PROFILE(call, proto, args)				\
-static void ftrace_profile_##call(proto)				\
-{									\
-	extern void perf_tpcounter_event(int);				\
-	perf_tpcounter_event(event_##call.id);				\
-}									\
-									\
-static int ftrace_profile_enable_##call(struct ftrace_event_call *event_call) \
-{									\
-	int ret = 0;							\
-									\
-	if (!atomic_inc_return(&event_call->profile_count))		\
-		ret = register_trace_##call(ftrace_profile_##call);	\
-									\
-	return ret;							\
-}									\
-									\
-static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\
-{									\
-	if (atomic_add_negative(-1, &event_call->profile_count))	\
-		unregister_trace_##call(ftrace_profile_##call);		\
-}
 
 #define _TRACE_PROFILE_INIT(call)					\
 	.profile_count = ATOMIC_INIT(-1),				\
@@ -476,7 +539,6 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\
 	.profile_disable = ftrace_profile_disable_##call,
 
 #else
-#define _TRACE_PROFILE(call, proto, args)
 #define _TRACE_PROFILE_INIT(call)
 #endif
 
@@ -502,7 +564,6 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\
 
 #undef TRACE_EVENT
 #define TRACE_EVENT(call, proto, args, tstruct, assign, print)		\
-_TRACE_PROFILE(call, PARAMS(proto), PARAMS(args))			\
 									\
 static struct ftrace_event_call event_##call;				\
 									\
@@ -586,6 +647,5 @@ __attribute__((section("_ftrace_events"))) event_##call = {		\
 
 #include TRACE_INCLUDE(TRACE_INCLUDE_FILE)
 
-#undef _TRACE_PROFILE
 #undef _TRACE_PROFILE_INIT
 
diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 673c1aaf733..52eb4b68d34 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -3703,17 +3703,17 @@ static const struct pmu perf_ops_task_clock = {
 };
 
 #ifdef CONFIG_EVENT_PROFILE
-void perf_tpcounter_event(int event_id)
+void perf_tpcounter_event(int event_id, u64 addr, u64 count)
 {
 	struct perf_sample_data data = {
 		.regs = get_irq_regs(),
-		.addr = 0,
+		.addr = addr,
 	};
 
 	if (!data.regs)
 		data.regs = task_pt_regs(current);
 
-	do_perf_swcounter_event(PERF_TYPE_TRACEPOINT, event_id, 1, 1, &data);
+	do_perf_swcounter_event(PERF_TYPE_TRACEPOINT, event_id, count, 1, &data);
 }
 EXPORT_SYMBOL_GPL(perf_tpcounter_event);
 
-- 
GitLab


From f413cdb80ce00ec1a4d0ab949b5d96c81cae7f75 Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Fri, 7 Aug 2009 01:25:54 +0200
Subject: [PATCH 0683/1153] perf_counter: Fix/complete ftrace event records
 sampling

This patch implements the kernel side support for ftrace event
record sampling.

A new counter sampling attribute is added:

   PERF_SAMPLE_TP_RECORD

which requests ftrace events record sampling. In this case
if a PERF_TYPE_TRACEPOINT counter is active and a tracepoint
fires, we emit the tracepoint binary record to the
perfcounter event buffer, as a sample.

Result, after setting PERF_SAMPLE_TP_RECORD attribute from perf
record:

 perf record -f -F 1 -a -e workqueue:workqueue_execution
 perf report -D

 0x21e18 [0x48]: event: 9
 .
 . ... raw event: size 72 bytes
 .  0000:  09 00 00 00 01 00 48 00 d0 c7 00 81 ff ff ff ff  ......H........
 .  0010:  0a 00 00 00 0a 00 00 00 21 00 00 00 00 00 00 00  ........!......
 .  0020:  2b 00 01 02 0a 00 00 00 0a 00 00 00 65 76 65 6e  +...........eve
 .  0030:  74 73 2f 31 00 00 00 00 00 00 00 00 0a 00 00 00  ts/1...........
 .  0040:  e0 b1 31 81 ff ff ff ff                          .......
.
0x21e18 [0x48]: PERF_EVENT_SAMPLE (IP, 1): 10: 0xffffffff8100c7d0 period: 33

The raw ftrace binary record starts at offset 0020.

Translation:

 struct trace_entry {
	type		= 0x2b = 43;
	flags		= 1;
	preempt_count	= 2;
	pid		= 0xa = 10;
	tgid		= 0xa = 10;
 }

 thread_comm = "events/1"
 thread_pid  = 0xa = 10;
 func	    = 0xffffffff8131b1e0 = flush_to_ldisc()

What will come next?

 - Userspace support ('perf trace'), 'flight data recorder' mode
   for perf trace, etc.

 - The unconditional copy from the profiling callback brings
   some costs however if someone wants no such sampling to
   occur, and needs to be fixed in the future. For that we need
   to have an instant access to the perf counter attribute.
   This is a matter of a flag to add in the struct ftrace_event.

 - Take care of the events recursivity! Don't ever try to record
   a lock event for example, it seems some locking is used in
   the profiling fast path and lead to a tracing recursivity.
   That will be fixed using raw spinlock or recursivity
   protection.

 - [...]

 - Profit! :-)

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 include/linux/ftrace_event.h |   4 +-
 include/linux/perf_counter.h |   9 ++-
 include/trace/ftrace.h       | 130 ++++++++++++++++++++++++++---------
 kernel/perf_counter.c        |  18 ++++-
 kernel/trace/trace.c         |   1 +
 kernel/trace/trace.h         |   4 --
 tools/perf/builtin-record.c  |   1 +
 7 files changed, 126 insertions(+), 41 deletions(-)

diff --git a/include/linux/ftrace_event.h b/include/linux/ftrace_event.h
index d7cd193c227..a81170de7f6 100644
--- a/include/linux/ftrace_event.h
+++ b/include/linux/ftrace_event.h
@@ -89,7 +89,9 @@ enum print_line_t {
 	TRACE_TYPE_NO_CONSUME	= 3	/* Handled but ask to not consume */
 };
 
-
+void tracing_generic_entry_update(struct trace_entry *entry,
+				  unsigned long flags,
+				  int pc);
 struct ring_buffer_event *
 trace_current_buffer_lock_reserve(int type, unsigned long len,
 				  unsigned long flags, int pc);
diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h
index e604e6ef72d..a67dd5c5b6d 100644
--- a/include/linux/perf_counter.h
+++ b/include/linux/perf_counter.h
@@ -121,8 +121,9 @@ enum perf_counter_sample_format {
 	PERF_SAMPLE_CPU				= 1U << 7,
 	PERF_SAMPLE_PERIOD			= 1U << 8,
 	PERF_SAMPLE_STREAM_ID			= 1U << 9,
+	PERF_SAMPLE_TP_RECORD			= 1U << 10,
 
-	PERF_SAMPLE_MAX = 1U << 10,		/* non-ABI */
+	PERF_SAMPLE_MAX = 1U << 11,		/* non-ABI */
 };
 
 /*
@@ -413,6 +414,11 @@ struct perf_callchain_entry {
 	__u64				ip[PERF_MAX_STACK_DEPTH];
 };
 
+struct perf_tracepoint_record {
+	int				size;
+	char				*record;
+};
+
 struct task_struct;
 
 /**
@@ -681,6 +687,7 @@ struct perf_sample_data {
 	struct pt_regs			*regs;
 	u64				addr;
 	u64				period;
+	void				*private;
 };
 
 extern int perf_counter_overflow(struct perf_counter *counter, int nmi,
diff --git a/include/trace/ftrace.h b/include/trace/ftrace.h
index fec71f8dbc4..7fb16d90e7b 100644
--- a/include/trace/ftrace.h
+++ b/include/trace/ftrace.h
@@ -353,15 +353,7 @@ static inline int ftrace_get_offsets_##call(				\
 /*
  * Generate the functions needed for tracepoint perf_counter support.
  *
- * static void ftrace_profile_<call>(proto)
- * {
- * 	extern void perf_tpcounter_event(int, u64, u64);
- * 	u64 __addr = 0, __count = 1;
- *
- * 	<assign>   <-- here we expand the TP_perf_assign() macro
- *
- * 	perf_tpcounter_event(event_<call>.id, __addr, __count);
- * }
+ * NOTE: The insertion profile callback (ftrace_profile_<call>) is defined later
  *
  * static int ftrace_profile_enable_<call>(struct ftrace_event_call *event_call)
  * {
@@ -381,28 +373,10 @@ static inline int ftrace_get_offsets_##call(				\
  *
  */
 
-#undef TP_fast_assign
-#define TP_fast_assign(args...)
-
-#undef TP_perf_assign
-#define TP_perf_assign(args...) args
-
-#undef __perf_addr
-#define __perf_addr(a) __addr = (a)
-
-#undef __perf_count
-#define __perf_count(c) __count = (c)
-
 #undef TRACE_EVENT
 #define TRACE_EVENT(call, proto, args, tstruct, assign, print)		\
 									\
-static void ftrace_profile_##call(proto)				\
-{									\
-	extern void perf_tpcounter_event(int, u64, u64);		\
-	u64 __addr = 0, __count = 1;					\
-	{ assign; }							\
-	perf_tpcounter_event(event_##call.id, __addr, __count);		\
-}									\
+static void ftrace_profile_##call(proto);				\
 									\
 static int ftrace_profile_enable_##call(struct ftrace_event_call *event_call) \
 {									\
@@ -422,12 +396,6 @@ static void ftrace_profile_disable_##call(struct ftrace_event_call *event_call)\
 
 #include TRACE_INCLUDE(TRACE_INCLUDE_FILE)
 
-#undef TP_fast_assign
-#define TP_fast_assign(args...) args
-
-#undef TP_perf_assign
-#define TP_perf_assign(args...)
-
 #endif
 
 /*
@@ -647,5 +615,99 @@ __attribute__((section("_ftrace_events"))) event_##call = {		\
 
 #include TRACE_INCLUDE(TRACE_INCLUDE_FILE)
 
+/*
+ * Define the insertion callback to profile events
+ *
+ * The job is very similar to ftrace_raw_event_<call> except that we don't
+ * insert in the ring buffer but in a perf counter.
+ *
+ * static void ftrace_profile_<call>(proto)
+ * {
+ *	struct ftrace_data_offsets_<call> __maybe_unused __data_offsets;
+ *	struct ftrace_event_call *event_call = &event_<call>;
+ *	extern void perf_tpcounter_event(int, u64, u64, void *, int);
+ *	struct ftrace_raw_##call *entry;
+ *	u64 __addr = 0, __count = 1;
+ *	unsigned long irq_flags;
+ *	int __entry_size;
+ *	int __data_size;
+ *	int pc;
+ *
+ *	local_save_flags(irq_flags);
+ *	pc = preempt_count();
+ *
+ *	__data_size = ftrace_get_offsets_<call>(&__data_offsets, args);
+ *	__entry_size = __data_size + sizeof(*entry);
+ *
+ *	do {
+ *		char raw_data[__entry_size]; <- allocate our sample in the stack
+ *		struct trace_entry *ent;
+ *
+ *		entry = (struct ftrace_raw_<call> *)raw_data;
+ *		ent = &entry->ent;
+ *		tracing_generic_entry_update(ent, irq_flags, pc);
+ *		ent->type = event_call->id;
+ *
+ *		<tstruct> <- do some jobs with dynamic arrays
+ *
+ *		<assign>  <- affect our values
+ *
+ *		perf_tpcounter_event(event_call->id, __addr, __count, entry,
+ *			     __entry_size);  <- submit them to perf counter
+ *	} while (0);
+ *
+ * }
+ */
+
+#ifdef CONFIG_EVENT_PROFILE
+
+#undef __perf_addr
+#define __perf_addr(a) __addr = (a)
+
+#undef __perf_count
+#define __perf_count(c) __count = (c)
+
+#undef TRACE_EVENT
+#define TRACE_EVENT(call, proto, args, tstruct, assign, print)		\
+static void ftrace_profile_##call(proto)				\
+{									\
+	struct ftrace_data_offsets_##call __maybe_unused __data_offsets;\
+	struct ftrace_event_call *event_call = &event_##call;		\
+	extern void perf_tpcounter_event(int, u64, u64, void *, int);	\
+	struct ftrace_raw_##call *entry;				\
+	u64 __addr = 0, __count = 1;					\
+	unsigned long irq_flags;					\
+	int __entry_size;						\
+	int __data_size;						\
+	int pc;								\
+									\
+	local_save_flags(irq_flags);					\
+	pc = preempt_count();						\
+									\
+	__data_size = ftrace_get_offsets_##call(&__data_offsets, args); \
+	__entry_size = ALIGN(__data_size + sizeof(*entry), sizeof(u64));\
+									\
+	do {								\
+		char raw_data[__entry_size];				\
+		struct trace_entry *ent;				\
+									\
+		entry = (struct ftrace_raw_##call *)raw_data;		\
+		ent = &entry->ent;					\
+		tracing_generic_entry_update(ent, irq_flags, pc);	\
+		ent->type = event_call->id;				\
+									\
+		tstruct							\
+									\
+		{ assign; }						\
+									\
+		perf_tpcounter_event(event_call->id, __addr, __count, entry,\
+			     __entry_size);				\
+	} while (0);							\
+									\
+}
+
+#include TRACE_INCLUDE(TRACE_INCLUDE_FILE)
+#endif /* CONFIG_EVENT_PROFILE */
+
 #undef _TRACE_PROFILE_INIT
 
diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 52eb4b68d34..868102172aa 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -2646,6 +2646,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 		u64 counter;
 	} group_entry;
 	struct perf_callchain_entry *callchain = NULL;
+	struct perf_tracepoint_record *tp;
 	int callchain_size = 0;
 	u64 time;
 	struct {
@@ -2714,6 +2715,11 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 			header.size += sizeof(u64);
 	}
 
+	if (sample_type & PERF_SAMPLE_TP_RECORD) {
+		tp = data->private;
+		header.size += tp->size;
+	}
+
 	ret = perf_output_begin(&handle, counter, header.size, nmi, 1);
 	if (ret)
 		return;
@@ -2777,6 +2783,9 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 		}
 	}
 
+	if (sample_type & PERF_SAMPLE_TP_RECORD)
+		perf_output_copy(&handle, tp->record, tp->size);
+
 	perf_output_end(&handle);
 }
 
@@ -3703,11 +3712,18 @@ static const struct pmu perf_ops_task_clock = {
 };
 
 #ifdef CONFIG_EVENT_PROFILE
-void perf_tpcounter_event(int event_id, u64 addr, u64 count)
+void perf_tpcounter_event(int event_id, u64 addr, u64 count, void *record,
+			  int entry_size)
 {
+	struct perf_tracepoint_record tp = {
+		.size = entry_size,
+		.record = record,
+	};
+
 	struct perf_sample_data data = {
 		.regs = get_irq_regs(),
 		.addr = addr,
+		.private = &tp,
 	};
 
 	if (!data.regs)
diff --git a/kernel/trace/trace.c b/kernel/trace/trace.c
index 8930e39b9d8..c22b40f8f57 100644
--- a/kernel/trace/trace.c
+++ b/kernel/trace/trace.c
@@ -848,6 +848,7 @@ tracing_generic_entry_update(struct trace_entry *entry, unsigned long flags,
 		((pc & SOFTIRQ_MASK) ? TRACE_FLAG_SOFTIRQ : 0) |
 		(need_resched() ? TRACE_FLAG_NEED_RESCHED : 0);
 }
+EXPORT_SYMBOL_GPL(tracing_generic_entry_update);
 
 struct ring_buffer_event *trace_buffer_lock_reserve(struct trace_array *tr,
 						    int type,
diff --git a/kernel/trace/trace.h b/kernel/trace/trace.h
index 3548ae5cc78..8b9f4f6e955 100644
--- a/kernel/trace/trace.h
+++ b/kernel/trace/trace.h
@@ -438,10 +438,6 @@ struct trace_entry *tracing_get_trace_entry(struct trace_array *tr,
 struct trace_entry *trace_find_next_entry(struct trace_iterator *iter,
 					  int *ent_cpu, u64 *ent_ts);
 
-void tracing_generic_entry_update(struct trace_entry *entry,
-				  unsigned long flags,
-				  int pc);
-
 void default_wait_pipe(struct trace_iterator *iter);
 void poll_wait_pipe(struct trace_iterator *iter);
 
diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c
index 6da09928130..90c98082af1 100644
--- a/tools/perf/builtin-record.c
+++ b/tools/perf/builtin-record.c
@@ -412,6 +412,7 @@ static void create_counter(int counter, int cpu, pid_t pid)
 	if (call_graph)
 		attr->sample_type	|= PERF_SAMPLE_CALLCHAIN;
 
+
 	attr->mmap		= track;
 	attr->comm		= track;
 	attr->inherit		= (cpu < 0) && inherit;
-- 
GitLab


From 923c42c19944da214d697e312a040384a0e33e78 Mon Sep 17 00:00:00 2001
From: Mike Galbraith <efault@gmx.de>
Date: Wed, 22 Jul 2009 20:36:03 +0200
Subject: [PATCH 0684/1153] perf_counter tools: Fix/resurrect perf top
 annotation in a simple interactive form

perf top used to have annotation support, but it has bitrotted and
removed.

This patch restores that: it allows the user to select any symbol
in kernel space for source level annotation on the fly, switch
between event counters and alter display variables. When symbol
details are being displayed, stopping annotation reverts to normal.

known keys:
        [d]     select display delay.
        [e]     select display entries (lines).
        [E]     select annotation event counter.
        [f]     select normal display count filter.
        [F]     select annotation display count filter (percentage).
        [qQ]    quit.
        [s]     select annotation symbol and start annotation.
        [S]     stop annotation, revert to normal display.
        [z]     toggle event count zeroing.

Sample:
------------------------------------------------------------------------------
   PerfTop:   16719 irqs/sec  kernel:78.7% [cache-misses/cache-references/instructions/cycles],  (all, 4 CPUs)
------------------------------------------------------------------------------

Showing cache-misses for e1000_clean_rx_irq
  Events  Pcnt (>=3%)
       0  0.0%                  /* adjust length to remove Ethernet CRC */
       0  0.0%                  if (!(adapter->flags2 & FLAG2_CRC_STRIPPING))
       0  0.0%                          length -= 4;
     436  5.0%      f039:       41 f6 84 24 5c 29 00    testb  $0x1,0x295c(%r12)
       0  0.0%      f089:       8b 4d 84                mov    -0x7c(%rbp),%ecx
       0  0.0%      f08c:       48 83 ef 02             sub    $0x2,%rdi
       0  0.0%      f090:       48 83 ee 02             sub    $0x2,%rsi
     811  9.3%      f094:       f3 a4                   rep movsb %ds:(%rsi),%es:(%rdi)
       0  0.0%
       0  0.0%          while (rx_desc->status & E1000_RXD_STAT_DD) {
       0  0.0%      f114:       41 f6 47 0c 01          testb  $0x1,0xc(%r15)
    7226 82.6%      f119:       0f 85 24 fe ff ff       jne    ef43 <e1000_clean_rx_irq+0x84>

Available events:
        0 cache-misses
        1 cache-references
        2 instructions
        3 cycles
Enter details event counter: 2
------------------------------------------------------------------------------
   PerfTop:   15035 irqs/sec  kernel:79.0% [cache-misses/cache-references/instructions/cycles],  (all, 4 CPUs)
------------------------------------------------------------------------------

Showing instructions for e1000_clean_rx_irq
  Events  Pcnt (>=3%)
       0  0.0%                                 int *work_done, int work_to_do)
       0  0.0%  {
     175  0.9%      eebf:       55                      push   %rbp
    1898  9.8%      eec0:       48 89 e5                mov    %rsp,%rbp
       0  0.0%
       0  0.0%          i = rx_ring->next_to_clean;
     140  0.7%      ef0a:       0f b7 41 1a             movzwl 0x1a(%rcx),%eax
     670  3.4%      ef0e:       89 45 ac                mov    %eax,-0x54(%rbp)
       0  0.0%  {
       0  0.0%          memcpy(skb->data + offset, from, len);
      91  0.5%      f07b:       49 8b b6 e8 00 00 00    mov    0xe8(%r14),%rsi
    1153  5.9%      f082:       48 8b b8 e8 00 00 00    mov    0xe8(%rax),%rdi
      42  0.2%      f089:       8b 4d 84                mov    -0x7c(%rbp),%ecx
      14  0.1%      f08c:       48 83 ef 02             sub    $0x2,%rdi
       0  0.0%      f090:       48 83 ee 02             sub    $0x2,%rsi
    1618  8.3%      f094:       f3 a4                   rep movsb %ds:(%rsi),%es:(%rdi)
       0  0.0%
       0  0.0%                  /* return some buffers to hardware, one at a time is too slow */
       0  0.0%                  if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
     867  4.5%      f0e7:       83 7d b0 0f             cmpl   $0xf,-0x50(%rbp)
       0  0.0%
       0  0.0%          while (rx_desc->status & E1000_RXD_STAT_DD) {
      37  0.2%      f114:       41 f6 47 0c 01          testb  $0x1,0xc(%r15)
    4047 20.8%      f119:       0f 85 24 fe ff ff       jne    ef43 <e1000_clean_rx_irq+0x84>

Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-top.c | 496 +++++++++++++++++++++++++++++++++++----
 1 file changed, 456 insertions(+), 40 deletions(-)

diff --git a/tools/perf/builtin-top.c b/tools/perf/builtin-top.c
index f139f1ab933..d58701346b1 100644
--- a/tools/perf/builtin-top.c
+++ b/tools/perf/builtin-top.c
@@ -31,6 +31,8 @@
 #include <fcntl.h>
 
 #include <stdio.h>
+#include <termios.h>
+#include <unistd.h>
 
 #include <errno.h>
 #include <time.h>
@@ -54,7 +56,7 @@ static int			system_wide			=  0;
 
 static int			default_interval		= 100000;
 
-static u64			count_filter			=  5;
+static int			count_filter			=  5;
 static int			print_entries			= 15;
 
 static int			target_pid			= -1;
@@ -69,14 +71,26 @@ static int			freq				=  0;
 static int			verbose				=  0;
 static char			*vmlinux			=  NULL;
 
-static char			*sym_filter;
-static unsigned long		filter_start;
-static unsigned long		filter_end;
-
 static int			delay_secs			=  2;
 static int			zero;
 static int			dump_symtab;
 
+/*
+ * Source
+ */
+
+struct source_line {
+	u64			eip;
+	unsigned long		count[MAX_COUNTERS];
+	char			*line;
+	struct source_line	*next;
+};
+
+static char			*sym_filter			=  NULL;
+struct sym_entry		*sym_filter_entry		=  NULL;
+static int			sym_pcnt_filter			=  5;
+static int			sym_counter			=  0;
+
 /*
  * Symbols
  */
@@ -91,9 +105,237 @@ struct sym_entry {
 	unsigned long		snap_count;
 	double			weight;
 	int			skip;
+	struct source_line	*source;
+	struct source_line	*lines;
+	struct source_line	**lines_tail;
+	pthread_mutex_t		source_lock;
 };
 
-struct sym_entry		*sym_filter_entry;
+/*
+ * Source functions
+ */
+
+static void parse_source(struct sym_entry *syme)
+{
+	struct symbol *sym;
+	struct module *module;
+	struct section *section = NULL;
+	FILE *file;
+	char command[PATH_MAX*2], *path = vmlinux;
+	u64 start, end, len;
+
+	if (!syme)
+		return;
+
+	if (syme->lines) {
+		pthread_mutex_lock(&syme->source_lock);
+		goto out_assign;
+	}
+
+	sym = (struct symbol *)(syme + 1);
+	module = sym->module;
+
+	if (module)
+		path = module->path;
+	if (!path)
+		return;
+
+	start = sym->obj_start;
+	if (!start)
+		start = sym->start;
+
+	if (module) {
+		section = module->sections->find_section(module->sections, ".text");
+		if (section)
+			start -= section->vma;
+	}
+
+	end = start + sym->end - sym->start + 1;
+	len = sym->end - sym->start;
+
+	sprintf(command, "objdump --start-address=0x%016Lx --stop-address=0x%016Lx -dS %s", start, end, path);
+
+	file = popen(command, "r");
+	if (!file)
+		return;
+
+	pthread_mutex_lock(&syme->source_lock);
+	syme->lines_tail = &syme->lines;
+	while (!feof(file)) {
+		struct source_line *src;
+		size_t dummy = 0;
+		char *c;
+
+		src = malloc(sizeof(struct source_line));
+		assert(src != NULL);
+		memset(src, 0, sizeof(struct source_line));
+
+		if (getline(&src->line, &dummy, file) < 0)
+			break;
+		if (!src->line)
+			break;
+
+		c = strchr(src->line, '\n');
+		if (c)
+			*c = 0;
+
+		src->next = NULL;
+		*syme->lines_tail = src;
+		syme->lines_tail = &src->next;
+
+		if (strlen(src->line)>8 && src->line[8] == ':') {
+			src->eip = strtoull(src->line, NULL, 16);
+			if (section)
+				src->eip += section->vma;
+		}
+		if (strlen(src->line)>8 && src->line[16] == ':') {
+			src->eip = strtoull(src->line, NULL, 16);
+			if (section)
+				src->eip += section->vma;
+		}
+	}
+	pclose(file);
+out_assign:
+	sym_filter_entry = syme;
+	pthread_mutex_unlock(&syme->source_lock);
+}
+
+static void __zero_source_counters(struct sym_entry *syme)
+{
+	int i;
+	struct source_line *line;
+
+	line = syme->lines;
+	while (line) {
+		for (i = 0; i < nr_counters; i++)
+			line->count[i] = 0;
+		line = line->next;
+	}
+}
+
+static void record_precise_ip(struct sym_entry *syme, int counter, u64 ip)
+{
+	struct source_line *line;
+
+	if (syme != sym_filter_entry)
+		return;
+
+	if (pthread_mutex_trylock(&syme->source_lock))
+		return;
+
+	if (!syme->source)
+		goto out_unlock;
+
+	for (line = syme->lines; line; line = line->next) {
+		if (line->eip == ip) {
+			line->count[counter]++;
+			break;
+		}
+		if (line->eip > ip)
+			break;
+	}
+out_unlock:
+	pthread_mutex_unlock(&syme->source_lock);
+}
+
+static void lookup_sym_source(struct sym_entry *syme)
+{
+	struct symbol *symbol = (struct symbol *)(syme + 1);
+	struct source_line *line;
+	char pattern[PATH_MAX];
+	char *idx;
+
+	sprintf(pattern, "<%s>:", symbol->name);
+
+	if (symbol->module) {
+		idx = strstr(pattern, "\t");
+		if (idx)
+			*idx = 0;
+	}
+
+	pthread_mutex_lock(&syme->source_lock);
+	for (line = syme->lines; line; line = line->next) {
+		if (strstr(line->line, pattern)) {
+			syme->source = line;
+			break;
+		}
+	}
+	pthread_mutex_unlock(&syme->source_lock);
+}
+
+static void show_lines(struct source_line *queue, int count, int total)
+{
+	int i;
+	struct source_line *line;
+
+	line = queue;
+	for (i = 0; i < count; i++) {
+		float pcnt = 100.0*(float)line->count[sym_counter]/(float)total;
+
+		printf("%8li %4.1f%%\t%s\n", line->count[sym_counter], pcnt, line->line);
+		line = line->next;
+	}
+}
+
+#define TRACE_COUNT     3
+
+static void show_details(struct sym_entry *syme)
+{
+	struct symbol *symbol;
+	struct source_line *line;
+	struct source_line *line_queue = NULL;
+	int displayed = 0;
+	int line_queue_count = 0, total = 0, more = 0;
+
+	if (!syme)
+		return;
+
+	if (!syme->source)
+		lookup_sym_source(syme);
+
+	if (!syme->source)
+		return;
+
+	symbol = (struct symbol *)(syme + 1);
+	printf("Showing %s for %s\n", event_name(sym_counter), symbol->name);
+	printf("  Events  Pcnt (>=%d%%)\n", sym_pcnt_filter);
+
+	pthread_mutex_lock(&syme->source_lock);
+	line = syme->source;
+	while (line) {
+		total += line->count[sym_counter];
+		line = line->next;
+	}
+
+	line = syme->source;
+	while (line) {
+		float pcnt = 0.0;
+
+		if (!line_queue_count)
+			line_queue = line;
+		line_queue_count++;
+
+		if (line->count[sym_counter])
+			pcnt = 100.0 * line->count[sym_counter] / (float)total;
+		if (pcnt >= (float)sym_pcnt_filter) {
+			if (displayed <= print_entries)
+				show_lines(line_queue, line_queue_count, total);
+			else more++;
+			displayed += line_queue_count;
+			line_queue_count = 0;
+			line_queue = NULL;
+		} else if (line_queue_count > TRACE_COUNT) {
+			line_queue = line_queue->next;
+			line_queue_count--;
+		}
+
+		line->count[sym_counter] = zero ? 0 : line->count[sym_counter] * 7 / 8;
+		line = line->next;
+	}
+	pthread_mutex_unlock(&syme->source_lock);
+	if (more)
+		printf("%d lines not displayed, maybe increase display entries [e]\n", more);
+}
 
 struct dso			*kernel_dso;
 
@@ -228,6 +470,11 @@ static void print_sym_table(void)
 
 	printf("------------------------------------------------------------------------------\n\n");
 
+	if (sym_filter_entry) {
+		show_details(sym_filter_entry);
+		return;
+	}
+
 	if (nr_counters == 1)
 		printf("             samples    pcnt");
 	else
@@ -242,7 +489,7 @@ static void print_sym_table(void)
 		struct symbol *sym = (struct symbol *)(syme + 1);
 		double pcnt;
 
-		if (++printed > print_entries || syme->snap_count < count_filter)
+		if (++printed > print_entries || (int)syme->snap_count < count_filter)
 			continue;
 
 		pcnt = 100.0 - (100.0 * ((sum_ksamples - syme->snap_count) /
@@ -261,19 +508,208 @@ static void print_sym_table(void)
 	}
 }
 
+static void prompt_integer(int *target, const char *msg)
+{
+	char *buf = malloc(0), *p;
+	size_t dummy = 0;
+	int tmp;
+
+	fprintf(stdout, "\n%s: ", msg);
+	if (getline(&buf, &dummy, stdin) < 0)
+		return;
+
+	p = strchr(buf, '\n');
+	if (p)
+		*p = 0;
+
+	p = buf;
+	while(*p) {
+		if (!isdigit(*p))
+			goto out_free;
+		p++;
+	}
+	tmp = strtoul(buf, NULL, 10);
+	*target = tmp;
+out_free:
+	free(buf);
+}
+
+static void prompt_percent(int *target, const char *msg)
+{
+	int tmp = 0;
+
+	prompt_integer(&tmp, msg);
+	if (tmp >= 0 && tmp <= 100)
+		*target = tmp;
+}
+
+static void prompt_symbol(struct sym_entry **target, const char *msg)
+{
+	char *buf = malloc(0), *p;
+	struct sym_entry *syme = *target, *n, *found = NULL;
+	size_t dummy = 0;
+
+	/* zero counters of active symbol */
+	if (syme) {
+		pthread_mutex_lock(&syme->source_lock);
+		__zero_source_counters(syme);
+		*target = NULL;
+		pthread_mutex_unlock(&syme->source_lock);
+	}
+
+	fprintf(stdout, "\n%s: ", msg);
+	if (getline(&buf, &dummy, stdin) < 0)
+		goto out_free;
+
+	p = strchr(buf, '\n');
+	if (p)
+		*p = 0;
+
+	pthread_mutex_lock(&active_symbols_lock);
+	syme = list_entry(active_symbols.next, struct sym_entry, node);
+	pthread_mutex_unlock(&active_symbols_lock);
+
+	list_for_each_entry_safe_from(syme, n, &active_symbols, node) {
+		struct symbol *sym = (struct symbol *)(syme + 1);
+
+		if (!strcmp(buf, sym->name)) {
+			found = syme;
+			break;
+		}
+	}
+
+	if (!found) {
+		fprintf(stderr, "Sorry, %s is not active.\n", sym_filter);
+		sleep(1);
+		return;
+	} else
+		parse_source(found);
+
+out_free:
+	free(buf);
+}
+
+static void print_known_keys(void)
+{
+	fprintf(stdout, "\nknown keys:\n");
+	fprintf(stdout, "\t[d]     select display delay.\n");
+	fprintf(stdout, "\t[e]     select display entries (lines).\n");
+	fprintf(stdout, "\t[E]     select annotation event counter.\n");
+	fprintf(stdout, "\t[f]     select normal display count filter.\n");
+	fprintf(stdout, "\t[F]     select annotation display count filter (percentage).\n");
+	fprintf(stdout, "\t[qQ]    quit.\n");
+	fprintf(stdout, "\t[s]     select annotation symbol and start annotation.\n");
+	fprintf(stdout, "\t[S]     stop annotation, revert to normal display.\n");
+	fprintf(stdout, "\t[z]     toggle event count zeroing.\n");
+}
+
+static void handle_keypress(int c)
+{
+	int once = 0;
+repeat:
+	switch (c) {
+		case 'd':
+			prompt_integer(&delay_secs, "Enter display delay");
+			break;
+		case 'e':
+			prompt_integer(&print_entries, "Enter display entries (lines)");
+			break;
+		case 'E':
+			if (nr_counters > 1) {
+				int i;
+
+				fprintf(stderr, "\nAvailable events:");
+				for (i = 0; i < nr_counters; i++)
+					fprintf(stderr, "\n\t%d %s", i, event_name(i));
+
+				prompt_integer(&sym_counter, "Enter details event counter");
+
+				if (sym_counter >= nr_counters) {
+					fprintf(stderr, "Sorry, no such event, using %s.\n", event_name(0));
+					sym_counter = 0;
+					sleep(1);
+				}
+			} else sym_counter = 0;
+			break;
+		case 'f':
+			prompt_integer(&count_filter, "Enter display event count filter");
+			break;
+		case 'F':
+			prompt_percent(&sym_pcnt_filter, "Enter details display event filter (percent)");
+			break;
+		case 'q':
+		case 'Q':
+			printf("exiting.\n");
+			exit(0);
+		case 's':
+			prompt_symbol(&sym_filter_entry, "Enter details symbol");
+			break;
+		case 'S':
+			if (!sym_filter_entry)
+				break;
+			else {
+				struct sym_entry *syme = sym_filter_entry;
+
+				pthread_mutex_lock(&syme->source_lock);
+				sym_filter_entry = NULL;
+				__zero_source_counters(syme);
+				pthread_mutex_unlock(&syme->source_lock);
+			}
+			break;
+		case 'z':
+			zero = ~zero;
+			break;
+		default: {
+			struct pollfd stdin_poll = { .fd = 0, .events = POLLIN };
+			struct termios tc, save;
+
+			if (!once) {
+				print_known_keys();
+				once++;
+			}
+
+			tcgetattr(0, &save);
+			tc = save;
+			tc.c_lflag &= ~(ICANON | ECHO);
+			tc.c_cc[VMIN] = 0;
+			tc.c_cc[VTIME] = 0;
+			tcsetattr(0, TCSANOW, &tc);
+
+			poll(&stdin_poll, 1, -1);
+			c = getc(stdin);
+
+			tcsetattr(0, TCSAFLUSH, &save);
+			goto repeat;
+		}
+	}
+}
+
 static void *display_thread(void *arg __used)
 {
 	struct pollfd stdin_poll = { .fd = 0, .events = POLLIN };
-	int delay_msecs = delay_secs * 1000;
-
-	printf("PerfTop refresh period: %d seconds\n", delay_secs);
+	struct termios tc, save;
+	int delay_msecs, c;
+
+	tcgetattr(0, &save);
+	tc = save;
+	tc.c_lflag &= ~(ICANON | ECHO);
+	tc.c_cc[VMIN] = 0;
+	tc.c_cc[VTIME] = 0;
+repeat:
+	delay_msecs = delay_secs * 1000;
+	tcsetattr(0, TCSANOW, &tc);
+	/* trash return*/
+	getc(stdin);
 
 	do {
 		print_sym_table();
 	} while (!poll(&stdin_poll, 1, delay_msecs) == 1);
 
-	printf("key pressed - exiting.\n");
-	exit(0);
+	c = getc(stdin);
+	tcsetattr(0, TCSAFLUSH, &save);
+
+	handle_keypress(c);
+	goto repeat;
 
 	return NULL;
 }
@@ -293,7 +729,6 @@ static const char *skip_symbols[] = {
 
 static int symbol_filter(struct dso *self, struct symbol *sym)
 {
-	static int filter_match;
 	struct sym_entry *syme;
 	const char *name = sym->name;
 	int i;
@@ -315,6 +750,10 @@ static int symbol_filter(struct dso *self, struct symbol *sym)
 		return 1;
 
 	syme = dso__sym_priv(self, sym);
+	pthread_mutex_init(&syme->source_lock, NULL);
+	if (!sym_filter_entry && sym_filter && !strcmp(name, sym_filter))
+		sym_filter_entry = syme;
+
 	for (i = 0; skip_symbols[i]; i++) {
 		if (!strcmp(skip_symbols[i], name)) {
 			syme->skip = 1;
@@ -322,29 +761,6 @@ static int symbol_filter(struct dso *self, struct symbol *sym)
 		}
 	}
 
-	if (filter_match == 1) {
-		filter_end = sym->start;
-		filter_match = -1;
-		if (filter_end - filter_start > 10000) {
-			fprintf(stderr,
-				"hm, too large filter symbol <%s> - skipping.\n",
-				sym_filter);
-			fprintf(stderr, "symbol filter start: %016lx\n",
-				filter_start);
-			fprintf(stderr, "                end: %016lx\n",
-				filter_end);
-			filter_end = filter_start = 0;
-			sym_filter = NULL;
-			sleep(1);
-		}
-	}
-
-	if (filter_match == 0 && sym_filter && !strcmp(name, sym_filter)) {
-		filter_match = 1;
-		filter_start = sym->start;
-	}
-
-
 	return 0;
 }
 
@@ -380,8 +796,6 @@ out_delete_dso:
 	return -1;
 }
 
-#define TRACE_COUNT     3
-
 /*
  * Binary search in the histogram table and record the hit:
  */
@@ -394,6 +808,7 @@ static void record_ip(u64 ip, int counter)
 
 		if (!syme->skip) {
 			syme->count[counter]++;
+			record_precise_ip(syme, counter, ip);
 			pthread_mutex_lock(&active_symbols_lock);
 			if (list_empty(&syme->node) || !syme->node.next)
 				__list_insert_active_sym(syme);
@@ -690,8 +1105,8 @@ static const struct option options[] = {
 			    "put the counters into a counter group"),
 	OPT_BOOLEAN('i', "inherit", &inherit,
 		    "child tasks inherit counters"),
-	OPT_STRING('s', "sym-filter", &sym_filter, "pattern",
-		    "only display symbols matchig this pattern"),
+	OPT_STRING('s', "sym-annotate", &sym_filter, "symbol name",
+		    "symbol to annotate - requires -k option"),
 	OPT_BOOLEAN('z', "zero", &zero,
 		    "zero history across updates"),
 	OPT_INTEGER('F', "freq", &freq,
@@ -734,6 +1149,7 @@ int cmd_top(int argc, const char **argv, const char *prefix __used)
 		delay_secs = 1;
 
 	parse_symbols();
+	parse_source(sym_filter_entry);
 
 	/*
 	 * Fill in the ones not specifically initialized via -c:
-- 
GitLab


From 46ab976443c6c566c8fe6fc72a6733a55ba9fbea Mon Sep 17 00:00:00 2001
From: Mike Galbraith <efault@gmx.de>
Date: Fri, 24 Jul 2009 10:09:50 +0200
Subject: [PATCH 0685/1153] perf_counter tools: Allow perf top top users to
 switch between weighted and individual counter display

Add [w]eighted hotkey.  Pressing [w] toggles between displaying
weighted total of all counters, and the counter selected via
[E]vent select key.

------------------------------------------------------------------------------
   PerfTop:   90395 irqs/sec  kernel:16.1% [cache-misses/cache-references/instructions],  (all, 4 CPUs)
------------------------------------------------------------------------------

  weight     samples    pcnt         RIP          kernel function
  ______     _______   _____   ________________   _______________

1275408.6      10881 -  5.3% - ffffffff81146f70 : copy_page_c
 553683.4      43569 - 21.3% - ffffffff81146f20 : clear_page_c
  74075.0       6768 -  3.3% - ffffffff81147190 : copy_user_generic_string
  40602.9       7538 -  3.7% - ffffffff81284ba2 : _spin_lock
  26882.1        965 -  0.5% - ffffffff8109d280 : file_ra_state_init

[w]

------------------------------------------------------------------------------
   PerfTop:   91221 irqs/sec  kernel:14.5% [10000Hz cache-misses],  (all, 4 CPUs)
------------------------------------------------------------------------------

  weight     samples    pcnt         RIP          kernel function
  ______     _______   _____   ________________   _______________

            47320.00 - 22.3% - ffffffff81146f20 : clear_page_c
            14261.00 -  6.7% - ffffffff810992f5 : __rmqueue
            11046.00 -  5.2% - ffffffff81146f70 : copy_page_c
             7842.00 -  3.7% - ffffffff81284ba2 : _spin_lock
             7234.00 -  3.4% - ffffffff810aa1d6 : unmap_vmas

Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-top.c | 24 +++++++++++++++++-------
 1 file changed, 17 insertions(+), 7 deletions(-)

diff --git a/tools/perf/builtin-top.c b/tools/perf/builtin-top.c
index d58701346b1..4eef3465e83 100644
--- a/tools/perf/builtin-top.c
+++ b/tools/perf/builtin-top.c
@@ -90,6 +90,7 @@ static char			*sym_filter			=  NULL;
 struct sym_entry		*sym_filter_entry		=  NULL;
 static int			sym_pcnt_filter			=  5;
 static int			sym_counter			=  0;
+static int			display_weighted		= -1;
 
 /*
  * Symbols
@@ -354,6 +355,9 @@ static double sym_weight(const struct sym_entry *sym)
 	double weight = sym->snap_count;
 	int counter;
 
+	if (!display_weighted)
+		return weight;
+
 	for (counter = 1; counter < nr_counters-1; counter++)
 		weight *= sym->count[counter];
 
@@ -401,7 +405,7 @@ static void rb_insert_active_sym(struct rb_root *tree, struct sym_entry *se)
 static void print_sym_table(void)
 {
 	int printed = 0, j;
-	int counter;
+	int counter, snap = !display_weighted ? sym_counter : 0;
 	float samples_per_sec = samples/delay_secs;
 	float ksamples_per_sec = (samples-userspace_samples)/delay_secs;
 	float sum_ksamples = 0.0;
@@ -417,7 +421,7 @@ static void print_sym_table(void)
 	pthread_mutex_unlock(&active_symbols_lock);
 
 	list_for_each_entry_safe_from(syme, n, &active_symbols, node) {
-		syme->snap_count = syme->count[0];
+		syme->snap_count = syme->count[snap];
 		if (syme->snap_count != 0) {
 			syme->weight = sym_weight(syme);
 			rb_insert_active_sym(&tmp, syme);
@@ -437,7 +441,7 @@ static void print_sym_table(void)
 		samples_per_sec,
 		100.0 - (100.0*((samples_per_sec-ksamples_per_sec)/samples_per_sec)));
 
-	if (nr_counters == 1) {
+	if (nr_counters == 1 || !display_weighted) {
 		printf("%Ld", (u64)attrs[0].sample_period);
 		if (freq)
 			printf("Hz ");
@@ -445,7 +449,9 @@ static void print_sym_table(void)
 			printf(" ");
 	}
 
-	for (counter = 0; counter < nr_counters; counter++) {
+	if (!display_weighted)
+		printf("%s", event_name(sym_counter));
+	else for (counter = 0; counter < nr_counters; counter++) {
 		if (counter)
 			printf("/");
 
@@ -495,7 +501,7 @@ static void print_sym_table(void)
 		pcnt = 100.0 - (100.0 * ((sum_ksamples - syme->snap_count) /
 					 sum_ksamples));
 
-		if (nr_counters == 1)
+		if (nr_counters == 1 || !display_weighted)
 			printf("%20.2f - ", syme->weight);
 		else
 			printf("%9.1f %10ld - ", syme->weight, syme->snap_count);
@@ -594,13 +600,14 @@ static void print_known_keys(void)
 	fprintf(stdout, "\nknown keys:\n");
 	fprintf(stdout, "\t[d]     select display delay.\n");
 	fprintf(stdout, "\t[e]     select display entries (lines).\n");
-	fprintf(stdout, "\t[E]     select annotation event counter.\n");
+	fprintf(stdout, "\t[E]     active event counter.              \t(%s)\n", event_name(sym_counter));
 	fprintf(stdout, "\t[f]     select normal display count filter.\n");
 	fprintf(stdout, "\t[F]     select annotation display count filter (percentage).\n");
 	fprintf(stdout, "\t[qQ]    quit.\n");
 	fprintf(stdout, "\t[s]     select annotation symbol and start annotation.\n");
 	fprintf(stdout, "\t[S]     stop annotation, revert to normal display.\n");
-	fprintf(stdout, "\t[z]     toggle event count zeroing.\n");
+	fprintf(stdout, "\t[w]     toggle display weighted/count[E]r. \t(%d)\n", display_weighted ? 1 : 0);
+	fprintf(stdout, "\t[z]     toggle sample zeroing.             \t(%d)\n", zero ? 1 : 0);
 }
 
 static void handle_keypress(int c)
@@ -656,6 +663,9 @@ repeat:
 				pthread_mutex_unlock(&syme->source_lock);
 			}
 			break;
+		case 'w':
+			display_weighted = ~display_weighted;
+			break;
 		case 'z':
 			zero = ~zero;
 			break;
-- 
GitLab


From 7b4b6658e152ed4568cfff48175d93645df081d1 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Wed, 22 Jul 2009 09:29:32 +0200
Subject: [PATCH 0686/1153] perf_counter: Fix software counters for fast moving
 event sources

Reimplement the software counters to deal with fast moving
event sources (such as tracepoints). This means being able
to generate multiple overflows from a single 'event' as well
as support throttling.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 164 ++++++++++++++++++++++++------------------
 1 file changed, 94 insertions(+), 70 deletions(-)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 868102172aa..615440ab929 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -3344,87 +3344,81 @@ int perf_counter_overflow(struct perf_counter *counter, int nmi,
  * Generic software counter infrastructure
  */
 
-static void perf_swcounter_update(struct perf_counter *counter)
+/*
+ * We directly increment counter->count and keep a second value in
+ * counter->hw.period_left to count intervals. This period counter
+ * is kept in the range [-sample_period, 0] so that we can use the
+ * sign as trigger.
+ */
+
+static u64 perf_swcounter_set_period(struct perf_counter *counter)
 {
 	struct hw_perf_counter *hwc = &counter->hw;
-	u64 prev, now;
-	s64 delta;
+	u64 period = hwc->last_period;
+	u64 nr, offset;
+	s64 old, val;
+
+	hwc->last_period = hwc->sample_period;
 
 again:
-	prev = atomic64_read(&hwc->prev_count);
-	now = atomic64_read(&hwc->count);
-	if (atomic64_cmpxchg(&hwc->prev_count, prev, now) != prev)
-		goto again;
+	old = val = atomic64_read(&hwc->period_left);
+	if (val < 0)
+		return 0;
 
-	delta = now - prev;
+	nr = div64_u64(period + val, period);
+	offset = nr * period;
+	val -= offset;
+	if (atomic64_cmpxchg(&hwc->period_left, old, val) != old)
+		goto again;
 
-	atomic64_add(delta, &counter->count);
-	atomic64_sub(delta, &hwc->period_left);
+	return nr;
 }
 
-static void perf_swcounter_set_period(struct perf_counter *counter)
+static void perf_swcounter_overflow(struct perf_counter *counter,
+				    int nmi, struct perf_sample_data *data)
 {
 	struct hw_perf_counter *hwc = &counter->hw;
-	s64 left = atomic64_read(&hwc->period_left);
-	s64 period = hwc->sample_period;
+	u64 overflow;
 
-	if (unlikely(left <= -period)) {
-		left = period;
-		atomic64_set(&hwc->period_left, left);
-		hwc->last_period = period;
-	}
+	data->period = counter->hw.last_period;
+	overflow = perf_swcounter_set_period(counter);
 
-	if (unlikely(left <= 0)) {
-		left += period;
-		atomic64_add(period, &hwc->period_left);
-		hwc->last_period = period;
-	}
+	if (hwc->interrupts == MAX_INTERRUPTS)
+		return;
 
-	atomic64_set(&hwc->prev_count, -left);
-	atomic64_set(&hwc->count, -left);
+	for (; overflow; overflow--) {
+		if (perf_counter_overflow(counter, nmi, data)) {
+			/*
+			 * We inhibit the overflow from happening when
+			 * hwc->interrupts == MAX_INTERRUPTS.
+			 */
+			break;
+		}
+	}
 }
 
-static enum hrtimer_restart perf_swcounter_hrtimer(struct hrtimer *hrtimer)
+static void perf_swcounter_unthrottle(struct perf_counter *counter)
 {
-	enum hrtimer_restart ret = HRTIMER_RESTART;
-	struct perf_sample_data data;
-	struct perf_counter *counter;
-	u64 period;
-
-	counter	= container_of(hrtimer, struct perf_counter, hw.hrtimer);
-	counter->pmu->read(counter);
-
-	data.addr = 0;
-	data.regs = get_irq_regs();
 	/*
-	 * In case we exclude kernel IPs or are somehow not in interrupt
-	 * context, provide the next best thing, the user IP.
+	 * Nothing to do, we already reset hwc->interrupts.
 	 */
-	if ((counter->attr.exclude_kernel || !data.regs) &&
-			!counter->attr.exclude_user)
-		data.regs = task_pt_regs(current);
+}
 
-	if (data.regs) {
-		if (perf_counter_overflow(counter, 0, &data))
-			ret = HRTIMER_NORESTART;
-	}
+static void perf_swcounter_add(struct perf_counter *counter, u64 nr,
+			       int nmi, struct perf_sample_data *data)
+{
+	struct hw_perf_counter *hwc = &counter->hw;
 
-	period = max_t(u64, 10000, counter->hw.sample_period);
-	hrtimer_forward_now(hrtimer, ns_to_ktime(period));
+	atomic64_add(nr, &counter->count);
 
-	return ret;
-}
+	if (!hwc->sample_period)
+		return;
 
-static void perf_swcounter_overflow(struct perf_counter *counter,
-				    int nmi, struct perf_sample_data *data)
-{
-	data->period = counter->hw.last_period;
+	if (!data->regs)
+		return;
 
-	perf_swcounter_update(counter);
-	perf_swcounter_set_period(counter);
-	if (perf_counter_overflow(counter, nmi, data))
-		/* soft-disable the counter */
-		;
+	if (!atomic64_add_negative(nr, &hwc->period_left))
+		perf_swcounter_overflow(counter, nmi, data);
 }
 
 static int perf_swcounter_is_counting(struct perf_counter *counter)
@@ -3488,15 +3482,6 @@ static int perf_swcounter_match(struct perf_counter *counter,
 	return 1;
 }
 
-static void perf_swcounter_add(struct perf_counter *counter, u64 nr,
-			       int nmi, struct perf_sample_data *data)
-{
-	int neg = atomic64_add_negative(nr, &counter->hw.count);
-
-	if (counter->hw.sample_period && !neg && data->regs)
-		perf_swcounter_overflow(counter, nmi, data);
-}
-
 static void perf_swcounter_ctx_event(struct perf_counter_context *ctx,
 				     enum perf_type_id type,
 				     u32 event, u64 nr, int nmi,
@@ -3575,26 +3560,65 @@ void __perf_swcounter_event(u32 event, u64 nr, int nmi,
 
 static void perf_swcounter_read(struct perf_counter *counter)
 {
-	perf_swcounter_update(counter);
 }
 
 static int perf_swcounter_enable(struct perf_counter *counter)
 {
-	perf_swcounter_set_period(counter);
+	struct hw_perf_counter *hwc = &counter->hw;
+
+	if (hwc->sample_period) {
+		hwc->last_period = hwc->sample_period;
+		perf_swcounter_set_period(counter);
+	}
 	return 0;
 }
 
 static void perf_swcounter_disable(struct perf_counter *counter)
 {
-	perf_swcounter_update(counter);
 }
 
 static const struct pmu perf_ops_generic = {
 	.enable		= perf_swcounter_enable,
 	.disable	= perf_swcounter_disable,
 	.read		= perf_swcounter_read,
+	.unthrottle	= perf_swcounter_unthrottle,
 };
 
+/*
+ * hrtimer based swcounter callback
+ */
+
+static enum hrtimer_restart perf_swcounter_hrtimer(struct hrtimer *hrtimer)
+{
+	enum hrtimer_restart ret = HRTIMER_RESTART;
+	struct perf_sample_data data;
+	struct perf_counter *counter;
+	u64 period;
+
+	counter	= container_of(hrtimer, struct perf_counter, hw.hrtimer);
+	counter->pmu->read(counter);
+
+	data.addr = 0;
+	data.regs = get_irq_regs();
+	/*
+	 * In case we exclude kernel IPs or are somehow not in interrupt
+	 * context, provide the next best thing, the user IP.
+	 */
+	if ((counter->attr.exclude_kernel || !data.regs) &&
+			!counter->attr.exclude_user)
+		data.regs = task_pt_regs(current);
+
+	if (data.regs) {
+		if (perf_counter_overflow(counter, 0, &data))
+			ret = HRTIMER_NORESTART;
+	}
+
+	period = max_t(u64, 10000, counter->hw.sample_period);
+	hrtimer_forward_now(hrtimer, ns_to_ktime(period));
+
+	return ret;
+}
+
 /*
  * Software counter: cpu wall time clock
  */
-- 
GitLab


From 091bd2e993fcb1094a23e36157285b62bc87afdf Mon Sep 17 00:00:00 2001
From: Mike Galbraith <efault@gmx.de>
Date: Tue, 4 Aug 2009 10:21:23 +0200
Subject: [PATCH 0687/1153] perf top: Improve interactive key handling

Pressing any key which is not currently mapped to
functionality, based on startup command line options, displays
currently mapped keys, and prompts for input.

Pressing any unmapped key at the prompt returns the user to
display mode with variables unchanged.  eg, pressing ? <SPACE>
<ESC> etc displays currently available keys, the value of the
variable associated with that key, and prompts.

Pressing same again aborts input.

Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-top.c | 108 ++++++++++++++++++++++++++-------------
 1 file changed, 73 insertions(+), 35 deletions(-)

diff --git a/tools/perf/builtin-top.c b/tools/perf/builtin-top.c
index 4eef3465e83..7de28ce9ca2 100644
--- a/tools/perf/builtin-top.c
+++ b/tools/perf/builtin-top.c
@@ -595,25 +595,84 @@ out_free:
 	free(buf);
 }
 
-static void print_known_keys(void)
+static void print_mapped_keys(void)
 {
-	fprintf(stdout, "\nknown keys:\n");
-	fprintf(stdout, "\t[d]     select display delay.\n");
-	fprintf(stdout, "\t[e]     select display entries (lines).\n");
-	fprintf(stdout, "\t[E]     active event counter.              \t(%s)\n", event_name(sym_counter));
-	fprintf(stdout, "\t[f]     select normal display count filter.\n");
-	fprintf(stdout, "\t[F]     select annotation display count filter (percentage).\n");
-	fprintf(stdout, "\t[qQ]    quit.\n");
-	fprintf(stdout, "\t[s]     select annotation symbol and start annotation.\n");
-	fprintf(stdout, "\t[S]     stop annotation, revert to normal display.\n");
-	fprintf(stdout, "\t[w]     toggle display weighted/count[E]r. \t(%d)\n", display_weighted ? 1 : 0);
+	char *name = NULL;
+
+	if (sym_filter_entry) {
+		struct symbol *sym = (struct symbol *)(sym_filter_entry+1);
+		name = sym->name;
+	}
+
+	fprintf(stdout, "\nMapped keys:\n");
+	fprintf(stdout, "\t[d]     display refresh delay.             \t(%d)\n", delay_secs);
+	fprintf(stdout, "\t[e]     display entries (lines).           \t(%d)\n", print_entries);
+
+	if (nr_counters > 1)
+		fprintf(stdout, "\t[E]     active event counter.              \t(%s)\n", event_name(sym_counter));
+
+	fprintf(stdout, "\t[f]     profile display filter (count).    \t(%d)\n", count_filter);
+
+	if (vmlinux) {
+		fprintf(stdout, "\t[F]     annotate display filter (percent). \t(%d%%)\n", sym_pcnt_filter);
+		fprintf(stdout, "\t[s]     annotate symbol.                   \t(%s)\n", name?: "NULL");
+		fprintf(stdout, "\t[S]     stop annotation.\n");
+	}
+
+	if (nr_counters > 1)
+		fprintf(stdout, "\t[w]     toggle display weighted/count[E]r. \t(%d)\n", display_weighted ? 1 : 0);
+
 	fprintf(stdout, "\t[z]     toggle sample zeroing.             \t(%d)\n", zero ? 1 : 0);
+	fprintf(stdout, "\t[qQ]    quit.\n");
+}
+
+static int key_mapped(int c)
+{
+	switch (c) {
+		case 'd':
+		case 'e':
+		case 'f':
+		case 'z':
+		case 'q':
+		case 'Q':
+			return 1;
+		case 'E':
+		case 'w':
+			return nr_counters > 1 ? 1 : 0;
+		case 'F':
+		case 's':
+		case 'S':
+			return vmlinux ? 1 : 0;
+	}
+
+	return 0;
 }
 
 static void handle_keypress(int c)
 {
-	int once = 0;
-repeat:
+	if (!key_mapped(c)) {
+		struct pollfd stdin_poll = { .fd = 0, .events = POLLIN };
+		struct termios tc, save;
+
+		print_mapped_keys();
+		fprintf(stdout, "\nEnter selection, or unmapped key to continue: ");
+		fflush(stdout);
+
+		tcgetattr(0, &save);
+		tc = save;
+		tc.c_lflag &= ~(ICANON | ECHO);
+		tc.c_cc[VMIN] = 0;
+		tc.c_cc[VTIME] = 0;
+		tcsetattr(0, TCSANOW, &tc);
+
+		poll(&stdin_poll, 1, -1);
+		c = getc(stdin);
+
+		tcsetattr(0, TCSAFLUSH, &save);
+		if (!key_mapped(c))
+			return;
+	}
+
 	switch (c) {
 		case 'd':
 			prompt_integer(&delay_secs, "Enter display delay");
@@ -669,28 +728,6 @@ repeat:
 		case 'z':
 			zero = ~zero;
 			break;
-		default: {
-			struct pollfd stdin_poll = { .fd = 0, .events = POLLIN };
-			struct termios tc, save;
-
-			if (!once) {
-				print_known_keys();
-				once++;
-			}
-
-			tcgetattr(0, &save);
-			tc = save;
-			tc.c_lflag &= ~(ICANON | ECHO);
-			tc.c_cc[VMIN] = 0;
-			tc.c_cc[VTIME] = 0;
-			tcsetattr(0, TCSANOW, &tc);
-
-			poll(&stdin_poll, 1, -1);
-			c = getc(stdin);
-
-			tcsetattr(0, TCSAFLUSH, &save);
-			goto repeat;
-		}
 	}
 }
 
@@ -705,6 +742,7 @@ static void *display_thread(void *arg __used)
 	tc.c_lflag &= ~(ICANON | ECHO);
 	tc.c_cc[VMIN] = 0;
 	tc.c_cc[VTIME] = 0;
+
 repeat:
 	delay_msecs = delay_secs * 1000;
 	tcsetattr(0, TCSANOW, &tc);
-- 
GitLab


From 836179834833272f89098c6d1e1b89e8e69797c2 Mon Sep 17 00:00:00 2001
From: Mike Galbraith <efault@gmx.de>
Date: Tue, 4 Aug 2009 10:24:41 +0200
Subject: [PATCH 0688/1153] perf top: Update man page

perf_counter tools: update perf top manual page to reflect
current implementation.

Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Documentation/perf-top.txt | 112 +++++++++++++++++++++++---
 1 file changed, 99 insertions(+), 13 deletions(-)

diff --git a/tools/perf/Documentation/perf-top.txt b/tools/perf/Documentation/perf-top.txt
index 539d0128972..4a7d558dc30 100644
--- a/tools/perf/Documentation/perf-top.txt
+++ b/tools/perf/Documentation/perf-top.txt
@@ -3,36 +3,122 @@ perf-top(1)
 
 NAME
 ----
-perf-top - Run a command and profile it
+perf-top - System profiling tool.
 
 SYNOPSIS
 --------
 [verse]
-'perf top' [-e <EVENT> | --event=EVENT] [-l] [-a] <command>
+'perf top' [-e <EVENT> | --event=EVENT] [<options>]
 
 DESCRIPTION
 -----------
-This command runs a command and gathers a performance counter profile
-from it.
+This command generates and displays a performance counter profile in realtime.
 
 
 OPTIONS
 -------
-<command>...::
-	Any command you can specify in a shell.
+-a::
+--all-cpus::
+        System-wide collection.  (default)
+
+-c <count>::
+--count=<count>::
+	Event period to sample.
+
+-C <cpu>::
+--CPU=<cpu>::
+	CPU to profile.
+
+-d <seconds>::
+--delay=<seconds>::
+	Number of seconds to delay between refreshes.
 
--e::
---event=::
+-e <event>::
+--event=<event>::
 	Select the PMU event. Selection can be a symbolic event name
 	(use 'perf list' to list all events) or a raw PMU
 	event (eventsel+umask) in the form of rNNN where NNN is a
-	 hexadecimal event descriptor.
+	hexadecimal event descriptor.
 
--a::
-        system-wide collection
+-E <entries>::
+--entries=<entries>::
+	Display this many functions.
+
+-f <count>::
+--count-filter=<count>::
+	Only display functions with more events than this.
+
+-F <freq>::
+--freq=<freq>::
+	Profile at this frequency.
+
+-i::
+--inherit::
+	Child tasks inherit counters, only makes sens with -p option.
+
+-k <path>::
+--vmlinux=<path>::
+	Path to vmlinux.  Required for annotation functionality.
+
+-m <pages>::
+--mmap-pages=<pages>::
+	Number of mmapped data pages.
+
+-p <pid>::
+--pid=<pid>::
+	Profile events on existing pid.
+
+-r <priority>::
+--realtime=<priority>::
+	Collect data with this RT SCHED_FIFO priority.
+
+-s <symbol>::
+--sym-annotate=<symbol>::
+        Annotate this symbol.  Requires -k option.
+
+-v::
+--verbose::
+	Be more verbose (show counter open errors, etc).
+
+-z::
+--zero::
+	Zero history across display updates.
+
+INTERACTIVE PROMPTING KEYS
+--------------------------
+
+[d]::
+	Display refresh delay.
+
+[e]::
+	Number of entries to display.
+
+[E]::
+	Event to display when multiple counters are active.
+
+[f]::
+	Profile display filter (>= hit count).
+
+[F]::
+	Annotation display filter (>= % of total).
+
+[s]::
+	Annotate symbol.
+
+[S]::
+	Stop annotation, return to full profile display.
+
+[w]::
+	Toggle between weighted sum and individual count[E]r profile.
+
+[z]::
+	Toggle event count zeroing across display updates.
+
+[qQ]::
+	Quit.
+
+Pressing any unmapped key displays a menu, and prompts for input.
 
--l::
-        scale counter values
 
 SEE ALSO
 --------
-- 
GitLab


From 1953287bfe8afcbbd235bd6c42c9df06d52438dc Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Fri, 7 Aug 2009 07:11:05 +0200
Subject: [PATCH 0689/1153] perf tools: Fix call-chain cumul hit based
 sub-total (fractal mode)

The callchain fractal mode builds each new total hits in a new
branch of profiling by using the parent's hits of the current
branch plus the hits of the children.

This is wrong, the total hits of a branch should be made of the
sum of every children hits, we must ignore the parent hits in
this scope.

This patch also fixes another mistake with the hit counting.

Now the rates are correct.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-report.c |  4 ++--
 tools/perf/util/callchain.c | 27 ++++++++++++++++-----------
 tools/perf/util/callchain.h |  7 ++++++-
 3 files changed, 24 insertions(+), 14 deletions(-)

diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index 8cb58d68a00..da402e18656 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -901,7 +901,7 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self,
 	int i;
 
 	if (callchain_param.mode == CHAIN_GRAPH_REL)
-		new_total = self->cumul_hit;
+		new_total = self->children_hit;
 	else
 		new_total = total_samples;
 
@@ -930,7 +930,7 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self,
 			ret += ipchain__fprintf_graph(fp, chain, depth,
 						      new_depth_mask, i++,
 						      new_total,
-						      child->cumul_hit);
+						      cumul_hits(child));
 		}
 		ret += callchain__fprintf_graph(fp, child, new_total,
 						depth + 1,
diff --git a/tools/perf/util/callchain.c b/tools/perf/util/callchain.c
index 9d3c8141b8c..98c5627f327 100644
--- a/tools/perf/util/callchain.c
+++ b/tools/perf/util/callchain.c
@@ -26,10 +26,14 @@ rb_insert_callchain(struct rb_root *root, struct callchain_node *chain,
 	struct rb_node **p = &root->rb_node;
 	struct rb_node *parent = NULL;
 	struct callchain_node *rnode;
+	u64 chain_cumul = cumul_hits(chain);
 
 	while (*p) {
+		u64 rnode_cumul;
+
 		parent = *p;
 		rnode = rb_entry(parent, struct callchain_node, rb_node);
+		rnode_cumul = cumul_hits(rnode);
 
 		switch (mode) {
 		case CHAIN_FLAT:
@@ -40,7 +44,7 @@ rb_insert_callchain(struct rb_root *root, struct callchain_node *chain,
 			break;
 		case CHAIN_GRAPH_ABS: /* Falldown */
 		case CHAIN_GRAPH_REL:
-			if (rnode->cumul_hit < chain->cumul_hit)
+			if (rnode_cumul < chain_cumul)
 				p = &(*p)->rb_left;
 			else
 				p = &(*p)->rb_right;
@@ -87,7 +91,7 @@ static void __sort_chain_graph_abs(struct callchain_node *node,
 
 	chain_for_each_child(child, node) {
 		__sort_chain_graph_abs(child, min_hit);
-		if (child->cumul_hit >= min_hit)
+		if (cumul_hits(child) >= min_hit)
 			rb_insert_callchain(&node->rb_root, child,
 					    CHAIN_GRAPH_ABS);
 	}
@@ -108,11 +112,11 @@ static void __sort_chain_graph_rel(struct callchain_node *node,
 	u64 min_hit;
 
 	node->rb_root = RB_ROOT;
-	min_hit = node->cumul_hit * min_percent / 100.0;
+	min_hit = node->children_hit * min_percent / 100.0;
 
 	chain_for_each_child(child, node) {
 		__sort_chain_graph_rel(child, min_percent);
-		if (child->cumul_hit >= min_hit)
+		if (cumul_hits(child) >= min_hit)
 			rb_insert_callchain(&node->rb_root, child,
 					    CHAIN_GRAPH_REL);
 	}
@@ -211,7 +215,8 @@ add_child(struct callchain_node *parent, struct ip_callchain *chain,
 	new = create_child(parent, false);
 	fill_node(new, chain, start, syms);
 
-	new->cumul_hit = new->hit = 1;
+	new->children_hit = 0;
+	new->hit = 1;
 }
 
 /*
@@ -241,7 +246,8 @@ split_add_child(struct callchain_node *parent, struct ip_callchain *chain,
 
 	/* split the hits */
 	new->hit = parent->hit;
-	new->cumul_hit = parent->cumul_hit;
+	new->children_hit = parent->children_hit;
+	parent->children_hit = cumul_hits(new);
 	new->val_nr = parent->val_nr - idx_local;
 	parent->val_nr = idx_local;
 
@@ -249,6 +255,7 @@ split_add_child(struct callchain_node *parent, struct ip_callchain *chain,
 	if (idx_total < chain->nr) {
 		parent->hit = 0;
 		add_child(parent, chain, idx_total, syms);
+		parent->children_hit++;
 	} else {
 		parent->hit = 1;
 	}
@@ -269,13 +276,13 @@ __append_chain_children(struct callchain_node *root, struct ip_callchain *chain,
 		unsigned int ret = __append_chain(rnode, chain, start, syms);
 
 		if (!ret)
-			goto cumul;
+			goto inc_children_hit;
 	}
 	/* nothing in children, add to the current node */
 	add_child(root, chain, start, syms);
 
-cumul:
-	root->cumul_hit++;
+inc_children_hit:
+	root->children_hit++;
 }
 
 static int
@@ -317,8 +324,6 @@ __append_chain(struct callchain_node *root, struct ip_callchain *chain,
 	/* we match 100% of the path, increment the hit */
 	if (i - start == root->val_nr && i == chain->nr) {
 		root->hit++;
-		root->cumul_hit++;
-
 		return 0;
 	}
 
diff --git a/tools/perf/util/callchain.h b/tools/perf/util/callchain.h
index 7812122bea1..b2d128e07c8 100644
--- a/tools/perf/util/callchain.h
+++ b/tools/perf/util/callchain.h
@@ -21,7 +21,7 @@ struct callchain_node {
 	struct rb_root		rb_root; /* sorted tree of children */
 	unsigned int		val_nr;
 	u64			hit;
-	u64			cumul_hit; /* hit + hits of children */
+	u64			children_hit;
 };
 
 struct callchain_param;
@@ -48,6 +48,11 @@ static inline void callchain_init(struct callchain_node *node)
 	INIT_LIST_HEAD(&node->val);
 }
 
+static inline u64 cumul_hits(struct callchain_node *node)
+{
+	return node->hit + node->children_hit;
+}
+
 int register_callchain_param(struct callchain_param *param);
 void append_chain(struct callchain_node *root, struct ip_callchain *chain,
 		  struct symbol **syms);
-- 
GitLab


From 1c222bce7dd0cb9578b4c5cd3874a74f1db497c3 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Thu, 6 Aug 2009 20:57:41 +0200
Subject: [PATCH 0690/1153] perf tools: Fix multi-counter stat bug caused by
 incorrect reading of perf.data file header

Brice Goglin reported that only the first result from a
multi-counter perf record --stat run is accurate, the
rest looks bogus.

A silly mistake made us re-read the first attribute for
every recorded attribute.

Reported-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Cc: paulus@samba.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/util/header.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/tools/perf/util/header.c b/tools/perf/util/header.c
index 450384b3bbe..95a44bcfc2d 100644
--- a/tools/perf/util/header.c
+++ b/tools/perf/util/header.c
@@ -213,9 +213,10 @@ struct perf_header *perf_header__read(int fd)
 
 	for (i = 0; i < nr_attrs; i++) {
 		struct perf_header_attr *attr;
-		off_t tmp = lseek(fd, 0, SEEK_CUR);
+		off_t tmp;
 
 		do_read(fd, &f_attr, sizeof(f_attr));
+		tmp = lseek(fd, 0, SEEK_CUR);
 
 		attr = perf_header_attr__new(&f_attr.attr);
 
-- 
GitLab


From 8f18aec535b5ca513dd13b531730177d35175ffa Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Thu, 6 Aug 2009 19:40:28 +0200
Subject: [PATCH 0691/1153] perf report: Fix per task mult-counter stat
 reporting

Brice Goglin reported:

> I can easily sort them by thread id, but I don't know how to match
> my 4 events with each group of 4 lines.

Also report the counter id and the time running/enabled
stats (in case the counter got time-shared).

Reported-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-report.c    | 31 +++++++++++++++++++++++++++----
 tools/perf/util/parse-events.c |  8 +++++++-
 tools/perf/util/parse-events.h |  1 +
 3 files changed, 35 insertions(+), 5 deletions(-)

diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index da402e18656..84205462e07 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -112,7 +112,9 @@ struct read_event {
 	struct perf_event_header header;
 	u32 pid,tid;
 	u64 value;
-	u64 format[3];
+	u64 time_enabled;
+	u64 time_running;
+	u64 id;
 };
 
 typedef union event_union {
@@ -1690,14 +1692,37 @@ static void trace_event(event_t *event)
 	dprintf(".\n");
 }
 
+static struct perf_header	*header;
+
+static struct perf_counter_attr *perf_header__find_attr(u64 id)
+{
+	int i;
+
+	for (i = 0; i < header->attrs; i++) {
+		struct perf_header_attr *attr = header->attr[i];
+		int j;
+
+		for (j = 0; j < attr->ids; j++) {
+			if (attr->id[j] == id)
+				return &attr->attr;
+		}
+	}
+
+	return NULL;
+}
+
 static int
 process_read_event(event_t *event, unsigned long offset, unsigned long head)
 {
-	dprintf("%p [%p]: PERF_EVENT_READ: %d %d %Lu\n",
+	struct perf_counter_attr *attr = perf_header__find_attr(event->read.id);
+
+	dprintf("%p [%p]: PERF_EVENT_READ: %d %d %s %Lu\n",
 			(void *)(offset + head),
 			(void *)(long)(event->header.size),
 			event->read.pid,
 			event->read.tid,
+			attr ? __event_name(attr->type, attr->config)
+			     : "FAIL",
 			event->read.value);
 
 	return 0;
@@ -1743,8 +1768,6 @@ process_event(event_t *event, unsigned long offset, unsigned long head)
 	return 0;
 }
 
-static struct perf_header	*header;
-
 static u64 perf_header__sample_type(void)
 {
 	u64 sample_type = 0;
diff --git a/tools/perf/util/parse-events.c b/tools/perf/util/parse-events.c
index 7bdad8df22a..f77407b5832 100644
--- a/tools/perf/util/parse-events.c
+++ b/tools/perf/util/parse-events.c
@@ -223,9 +223,15 @@ char *event_name(int counter)
 {
 	u64 config = attrs[counter].config;
 	int type = attrs[counter].type;
+
+	return __event_name(type, config);
+}
+
+char *__event_name(int type, u64 config)
+{
 	static char buf[32];
 
-	if (attrs[counter].type == PERF_TYPE_RAW) {
+	if (type == PERF_TYPE_RAW) {
 		sprintf(buf, "raw 0x%llx", config);
 		return buf;
 	}
diff --git a/tools/perf/util/parse-events.h b/tools/perf/util/parse-events.h
index 1ea5d09b6eb..192a962e3a0 100644
--- a/tools/perf/util/parse-events.h
+++ b/tools/perf/util/parse-events.h
@@ -10,6 +10,7 @@ extern int			nr_counters;
 extern struct perf_counter_attr attrs[MAX_COUNTERS];
 
 extern char *event_name(int ctr);
+extern char *__event_name(int type, u64 config);
 
 extern int parse_events(const struct option *opt, const char *str, int unset);
 
-- 
GitLab


From 94cb9e385d5b4d55a5ae389baa10ad2835ea39bb Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Thu, 6 Aug 2009 14:43:17 -0300
Subject: [PATCH 0692/1153] perf report: Add debug help for the finding of
 symbol bugs - show the symtab origin (DSO, build-id, kernel, etc)

Used with perf report --verbose:

[acme@doppio linux-2.6-tip]$ perf report -v | head -16
     5.17%  firefox  /usr/lib64/xulrunner-1.9.1/libxul.so   0x00000000005d8eee f [.] imgContainer::DrawFrameTo(gfxIImageFrame*, gfxIImageFrame*, nsRect&)
     2.56%  firefox  /lib64/libpthread-2.10.1.so            0x0000000000008e02 d [.] __pthread_mutex_lock_internal
     1.94%  firefox  /usr/lib64/xulrunner-1.9.1/libxul.so   0x0000000000d0af8f f [.] SearchTable
     1.75%  firefox  [kernel]                               0xffffffffff60013b k [.] vread_hpet
     1.63%  firefox  /lib64/libpthread-2.10.1.so            0x000000000000a404 d [.] __pthread_mutex_unlock
     1.47%  firefox  /usr/lib64/xulrunner-1.9.1/libmozjs.so 0x00000000000482ea f [.] js_Interpret
     1.42%  firefox  /usr/lib64/xulrunner-1.9.1/libmozjs.so 0x000000000003eda3 f [.] JS_CallTracer
     1.24%  firefox  [kernel]                               0xffffffff8102ca4a k [k] read_hpet
     1.16%  firefox  [kernel]                               0xffffffff810f3dd4 k [k] fget_light
     1.11%  firefox  /usr/lib64/xulrunner-1.9.1/libmozjs.so 0x00000000000567ff f [.] js_TraceObject
     0.98%  firefox  /usr/lib64/firefox-3.5.2/firefox       0x000000000000dd23 b [.] arena_ralloc
[acme@doppio linux-2.6-tip]$

The new field is just after the symbol address. To help in
figuring out symbol resolution bugs.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-report.c |  3 +-
 tools/perf/util/symbol.c    | 57 ++++++++++++++++++++++++++++++-------
 tools/perf/util/symbol.h    |  2 ++
 3 files changed, 50 insertions(+), 12 deletions(-)

diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index 84205462e07..a5e2f8df411 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -700,7 +700,8 @@ sort__sym_print(FILE *fp, struct hist_entry *self, unsigned int width __used)
 	size_t ret = 0;
 
 	if (verbose)
-		ret += repsep_fprintf(fp, "%#018llx  ", (u64)self->ip);
+		ret += repsep_fprintf(fp, "%#018llx %c ", (u64)self->ip,
+				      dso__symtab_origin(self->dso));
 
 	ret += repsep_fprintf(fp, "[%c] ", self->level);
 	if (self->sym) {
diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c
index 16ddca20294..f1dcede1430 100644
--- a/tools/perf/util/symbol.c
+++ b/tools/perf/util/symbol.c
@@ -24,6 +24,16 @@ const char *sym_hist_filter;
 #define DMGL_ANSI        (1 << 1)       /* Include const, volatile, etc */
 #endif
 
+enum dso_origin {
+	DSO__ORIG_KERNEL = 0,
+	DSO__ORIG_JAVA_JIT,
+	DSO__ORIG_FEDORA,
+	DSO__ORIG_UBUNTU,
+	DSO__ORIG_BUILDID,
+	DSO__ORIG_DSO,
+	DSO__ORIG_NOT_FOUND,
+};
+
 static struct symbol *symbol__new(u64 start, u64 len,
 				  const char *name, unsigned int priv_size,
 				  u64 obj_start, int verbose)
@@ -81,6 +91,7 @@ struct dso *dso__new(const char *name, unsigned int sym_priv_size)
 		self->sym_priv_size = sym_priv_size;
 		self->find_symbol = dso__find_symbol;
 		self->slen_calculated = 0;
+		self->origin = DSO__ORIG_NOT_FOUND;
 	}
 
 	return self;
@@ -710,7 +721,7 @@ static char *dso__read_build_id(struct dso *self, int verbose)
 		++raw;
 		bid += 2;
 	}
-	if (verbose)
+	if (verbose >= 2)
 		printf("%s(%s): %s\n", __func__, self->name, build_id);
 out_elf_end:
 	elf_end(elf);
@@ -720,11 +731,26 @@ out:
 	return build_id;
 }
 
+char dso__symtab_origin(const struct dso *self)
+{
+	static const char origin[] = {
+		[DSO__ORIG_KERNEL] =   'k',
+		[DSO__ORIG_JAVA_JIT] = 'j',
+		[DSO__ORIG_FEDORA] =   'f',
+		[DSO__ORIG_UBUNTU] =   'u',
+		[DSO__ORIG_BUILDID] =  'b',
+		[DSO__ORIG_DSO] =      'd',
+	};
+
+	if (self == NULL || self->origin == DSO__ORIG_NOT_FOUND)
+		return '!';
+	return origin[self->origin];
+}
+
 int dso__load(struct dso *self, symbol_filter_t filter, int verbose)
 {
 	int size = PATH_MAX;
 	char *name = malloc(size), *build_id = NULL;
-	int variant = 0;
 	int ret = -1;
 	int fd;
 
@@ -733,19 +759,26 @@ int dso__load(struct dso *self, symbol_filter_t filter, int verbose)
 
 	self->adjust_symbols = 0;
 
-	if (strncmp(self->name, "/tmp/perf-", 10) == 0)
-		return dso__load_perf_map(self, filter, verbose);
+	if (strncmp(self->name, "/tmp/perf-", 10) == 0) {
+		ret = dso__load_perf_map(self, filter, verbose);
+		self->origin = ret > 0 ? DSO__ORIG_JAVA_JIT :
+					 DSO__ORIG_NOT_FOUND;
+		return ret;
+	}
+
+	self->origin = DSO__ORIG_FEDORA - 1;
 
 more:
 	do {
-		switch (variant) {
-		case 0: /* Fedora */
+		self->origin++;
+		switch (self->origin) {
+		case DSO__ORIG_FEDORA:
 			snprintf(name, size, "/usr/lib/debug%s.debug", self->name);
 			break;
-		case 1: /* Ubuntu */
+		case DSO__ORIG_UBUNTU:
 			snprintf(name, size, "/usr/lib/debug%s", self->name);
 			break;
-		case 2:
+		case DSO__ORIG_BUILDID:
 			build_id = dso__read_build_id(self, verbose);
 			if (build_id != NULL) {
 				snprintf(name, size,
@@ -754,16 +787,15 @@ more:
 				free(build_id);
 				break;
 			}
-			variant++;
+			self->origin++;
 			/* Fall thru */
-		case 3: /* Sane people */
+		case DSO__ORIG_DSO:
 			snprintf(name, size, "%s", self->name);
 			break;
 
 		default:
 			goto out;
 		}
-		variant++;
 
 		fd = open(name, O_RDONLY);
 	} while (fd < 0);
@@ -899,6 +931,9 @@ int dso__load_kernel(struct dso *self, const char *vmlinux,
 	if (err <= 0)
 		err = dso__load_kallsyms(self, filter, verbose);
 
+	if (err > 0)
+		self->origin = DSO__ORIG_KERNEL;
+
 	return err;
 }
 
diff --git a/tools/perf/util/symbol.h b/tools/perf/util/symbol.h
index 2f92b21c712..1e003ec2f4b 100644
--- a/tools/perf/util/symbol.h
+++ b/tools/perf/util/symbol.h
@@ -26,6 +26,7 @@ struct dso {
 	unsigned int	 sym_priv_size;
 	unsigned char	 adjust_symbols;
 	unsigned char	 slen_calculated;
+	unsigned char	 origin;
 	char		 name[0];
 };
 
@@ -49,6 +50,7 @@ int dso__load_modules(struct dso *self, symbol_filter_t filter, int verbose);
 int dso__load(struct dso *self, symbol_filter_t filter, int verbose);
 
 size_t dso__fprintf(struct dso *self, FILE *fp);
+char dso__symtab_origin(const struct dso *self);
 
 void symbol__init(void);
 #endif /* _PERF_SYMBOL_ */
-- 
GitLab


From b26bc5a7f81474937e427b0c855eabee5ad56f89 Mon Sep 17 00:00:00 2001
From: Brice Goglin <Brice.Goglin@inria.fr>
Date: Fri, 7 Aug 2009 10:18:39 +0200
Subject: [PATCH 0693/1153] perf stat: Fix tool option consistency: rename
 -S/--scale to -c/--scale

We want to use a coherent flag for -S/--stat across all tools,
so free up -S in perf stat.

Signed-off-by: Brice Goglin <Brice.Goglin@inria.fr>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus@samba.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Documentation/perf-stat.txt | 2 +-
 tools/perf/builtin-stat.c              | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/tools/perf/Documentation/perf-stat.txt b/tools/perf/Documentation/perf-stat.txt
index 0d74346d21a..484080dd5b6 100644
--- a/tools/perf/Documentation/perf-stat.txt
+++ b/tools/perf/Documentation/perf-stat.txt
@@ -40,7 +40,7 @@ OPTIONS
 -a::
         system-wide collection
 
--S::
+-c::
         scale counter values
 
 EXAMPLES
diff --git a/tools/perf/builtin-stat.c b/tools/perf/builtin-stat.c
index f9510eeeb6c..b4b06c7903e 100644
--- a/tools/perf/builtin-stat.c
+++ b/tools/perf/builtin-stat.c
@@ -496,7 +496,7 @@ static const struct option options[] = {
 		    "stat events on existing pid"),
 	OPT_BOOLEAN('a', "all-cpus", &system_wide,
 		    "system-wide collection from all CPUs"),
-	OPT_BOOLEAN('S', "scale", &scale,
+	OPT_BOOLEAN('c', "scale", &scale,
 		    "scale/normalize counters"),
 	OPT_BOOLEAN('v', "verbose", &verbose,
 		    "be more verbose (show counter open errors, etc)"),
-- 
GitLab


From f36a1a133a947973efb8e6a1fbdcc23e4a011437 Mon Sep 17 00:00:00 2001
From: Paul Mackerras <paulus@samba.org>
Date: Fri, 7 Aug 2009 16:59:45 +1000
Subject: [PATCH 0694/1153] perf_counter/powerpc: Fix oops on cpus without
 perf_counter hardware support

If we have the powerpc perf_counter backend compiled in, but
the cpu we are running on is one where we don't support the
PMU, we currently oops in hw_perf_group_sched_in if we try to
use any counters, because ppmu is NULL in that case, and we
unconditionally dereference ppmu.

This fixes the problem by adding a check if ppmu is NULL at the
beginning of hw_perf_group_sched_in, and also at the beginning
of the other functions that get called from the perf_counter
core, i.e. hw_perf_disable, hw_perf_enable, and
hw_perf_counter_setup.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: benh@kernel.crashing.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/powerpc/kernel/perf_counter.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/powerpc/kernel/perf_counter.c b/arch/powerpc/kernel/perf_counter.c
index 809fdf94b95..70e1f57f7dd 100644
--- a/arch/powerpc/kernel/perf_counter.c
+++ b/arch/powerpc/kernel/perf_counter.c
@@ -518,6 +518,8 @@ void hw_perf_disable(void)
 	struct cpu_hw_counters *cpuhw;
 	unsigned long flags;
 
+	if (!ppmu)
+		return;
 	local_irq_save(flags);
 	cpuhw = &__get_cpu_var(cpu_hw_counters);
 
@@ -572,6 +574,8 @@ void hw_perf_enable(void)
 	int n_lim;
 	int idx;
 
+	if (!ppmu)
+		return;
 	local_irq_save(flags);
 	cpuhw = &__get_cpu_var(cpu_hw_counters);
 	if (!cpuhw->disabled) {
@@ -737,6 +741,8 @@ int hw_perf_group_sched_in(struct perf_counter *group_leader,
 	long i, n, n0;
 	struct perf_counter *sub;
 
+	if (!ppmu)
+		return 0;
 	cpuhw = &__get_cpu_var(cpu_hw_counters);
 	n0 = cpuhw->n_counters;
 	n = collect_events(group_leader, ppmu->n_counter - n0,
@@ -1281,6 +1287,8 @@ void hw_perf_counter_setup(int cpu)
 {
 	struct cpu_hw_counters *cpuhw = &per_cpu(cpu_hw_counters, cpu);
 
+	if (!ppmu)
+		return;
 	memset(cpuhw, 0, sizeof(*cpuhw));
 	cpuhw->mmcr[0] = MMCR0_FC;
 }
-- 
GitLab


From ae07b63f4b6728e1f98aa5c5416cfc1280f59f51 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <peterz@infradead.org>
Date: Thu, 6 Aug 2009 16:48:54 +0200
Subject: [PATCH 0695/1153] perf list: Fix the output to not include
 tracepoints without an id

Stop perf list from displaying tracepoints without an id file,
those are special tracepoints that are not interfaced to
perfcounters so listing them is erroneous and passing them as
events will produce no output.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Jason Baron <jbaron@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/util/parse-events.c | 18 +++++++++++++++++-
 1 file changed, 17 insertions(+), 1 deletion(-)

diff --git a/tools/perf/util/parse-events.c b/tools/perf/util/parse-events.c
index f77407b5832..4858d83b3b6 100644
--- a/tools/perf/util/parse-events.c
+++ b/tools/perf/util/parse-events.c
@@ -121,13 +121,29 @@ static unsigned long hw_cache_stat[C(MAX)] = {
 	   (strcmp(sys_dirent.d_name, ".")) &&				       \
 	   (strcmp(sys_dirent.d_name, "..")))
 
+static int tp_event_has_id(struct dirent *sys_dir, struct dirent *evt_dir)
+{
+	char evt_path[MAXPATHLEN];
+	int fd;
+
+	snprintf(evt_path, MAXPATHLEN, "%s/%s/%s/id", debugfs_path,
+			sys_dir->d_name, evt_dir->d_name);
+	fd = open(evt_path, O_RDONLY);
+	if (fd < 0)
+		return -EINVAL;
+	close(fd);
+
+	return 0;
+}
+
 #define for_each_event(sys_dirent, evt_dir, evt_dirent, evt_next, file, st)    \
 	while (!readdir_r(evt_dir, &evt_dirent, &evt_next) && evt_next)        \
 	if (snprintf(file, MAXPATHLEN, "%s/%s/%s", debugfs_path,	       \
 		     sys_dirent.d_name, evt_dirent.d_name) &&		       \
 	   (!stat(file, &st)) && (S_ISDIR(st.st_mode)) &&		       \
 	   (strcmp(evt_dirent.d_name, ".")) &&				       \
-	   (strcmp(evt_dirent.d_name, "..")))
+	   (strcmp(evt_dirent.d_name, "..")) &&				       \
+	   (!tp_event_has_id(&sys_dirent, &evt_dirent)))
 
 #define MAX_EVENT_LENGTH 30
 
-- 
GitLab


From 7eac7e9e726c1b136bd7e0ad6671ce315f48bb18 Mon Sep 17 00:00:00 2001
From: Pierre Habouzit <pierre.habouzit@intersec.com>
Date: Fri, 7 Aug 2009 14:16:00 +0200
Subject: [PATCH 0696/1153] perf util: Fix do_read() to fail on EOF instead of
 busy-looping

While toying with perf, I've noticed that perf record can
easily enter a busy loop when doing something as silly as:

    $ perf record -A ls

Yeah, do_read here really wants to read a known size, not being
able to should die(), not busy-loop ;)

That was the cause for the bug.

Signed-off-by: Pierre Habouzit <pierre.habouzit@intersec.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/util/header.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/tools/perf/util/header.c b/tools/perf/util/header.c
index 95a44bcfc2d..b92a457ca32 100644
--- a/tools/perf/util/header.c
+++ b/tools/perf/util/header.c
@@ -185,6 +185,8 @@ static void do_read(int fd, void *buf, size_t size)
 
 		if (ret < 0)
 			die("failed to read");
+		if (ret == 0)
+			die("failed to read: missing data");
 
 		size -= ret;
 		buf += ret;
-- 
GitLab


From 266e0e219888420a1a7cafc82e82891cf7b5a979 Mon Sep 17 00:00:00 2001
From: Pierre Habouzit <pierre.habouzit@intersec.com>
Date: Fri, 7 Aug 2009 14:16:01 +0200
Subject: [PATCH 0697/1153] perf record: Fix the -A UI for empty or
 non-existent perf.data

1. Ignore the -A argument if there is no perf.data file
2. Treat an empty file like a non existent file.

Else, perf will try to read the perf.data header, and fail with
an error.

Treating an empty file like a non-existent file makes sense,
since an interupted (as in SIGKILLed) perf could leave such
files around, and you don't want to annoy the user with errors
for files with no data in it.

Signed-off-by: Pierre Habouzit <pierre.habouzit@intersec.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-record.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c
index 90c98082af1..0345aad8eba 100644
--- a/tools/perf/builtin-record.c
+++ b/tools/perf/builtin-record.c
@@ -525,10 +525,14 @@ static int __cmd_record(int argc, const char **argv)
 	signal(SIGCHLD, sig_handler);
 	signal(SIGINT, sig_handler);
 
-	if (!stat(output_name, &st) && !force && !append_file) {
-		fprintf(stderr, "Error, output file %s exists, use -A to append or -f to overwrite.\n",
-				output_name);
-		exit(-1);
+	if (!stat(output_name, &st) && st.st_size) {
+		if (!force && !append_file) {
+			fprintf(stderr, "Error, output file %s exists, use -A to append or -f to overwrite.\n",
+					output_name);
+			exit(-1);
+		}
+	} else {
+		append_file = 0;
 	}
 
 	flags = O_CREAT|O_RDWR;
-- 
GitLab


From b0efe213f84f7fd5ccfe07053e3d9fb827b7c188 Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Sat, 8 Aug 2009 02:16:23 +0200
Subject: [PATCH 0698/1153] perf tools: callchain: Fix spurious 'perf report'
 warnings: ignore empty callchains

When the callchain tree comes to insert an empty backtrace, it
raises a spurious warning about the fact we are inserting an
empty. This is spurious because the radix tree assumes it did
something wrong to reach this state. But it didn't, we just met
an empty callchain that has to be ignored.

This happens occasionally with certain types of call-chain
recordings. If it happens it's a big nuisance as perf report
output starts with thousands of warning lines.

Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1249690585-9145-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/util/callchain.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/tools/perf/util/callchain.c b/tools/perf/util/callchain.c
index 98c5627f327..a8e67aa9ef4 100644
--- a/tools/perf/util/callchain.c
+++ b/tools/perf/util/callchain.c
@@ -336,5 +336,7 @@ __append_chain(struct callchain_node *root, struct ip_callchain *chain,
 void append_chain(struct callchain_node *root, struct ip_callchain *chain,
 		  struct symbol **syms)
 {
+	if (!chain->nr)
+		return;
 	__append_chain_children(root, chain, syms, 0);
 }
-- 
GitLab


From b1a88349c37624755b28ac3b3152b48f52c1f487 Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Sat, 8 Aug 2009 02:16:24 +0200
Subject: [PATCH 0699/1153] perf tools: callchain: Fix 'perf report' display to
 be callchain by default

If we recorded with -g option to record the callchain, right now
we require a -g option to perf report as well - and people reported
this as unnecessary complication: the user already specified -g
once, no need to require it a second time.

So if the recording includes call-chains, display the callchain by
default from perf report.

( The user can override this default using "-g none" option from
  perf report. )

Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1249690585-9145-3-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-report.c | 16 +++++++++++++++-
 tools/perf/util/callchain.h |  1 +
 2 files changed, 16 insertions(+), 1 deletion(-)

diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index a5e2f8df411..c4a8e108e52 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -68,7 +68,7 @@ static int		callchain;
 
 static
 struct callchain_param	callchain_param = {
-	.mode	= CHAIN_GRAPH_ABS,
+	.mode	= CHAIN_GRAPH_REL,
 	.min_percent = 0.5
 };
 
@@ -1836,6 +1836,13 @@ static int __cmd_report(void)
 					" -g?\n");
 			exit(-1);
 		}
+	} else if (callchain_param.mode != CHAIN_NONE && !callchain) {
+			callchain = 1;
+			if (register_callchain_param(&callchain_param) < 0) {
+				fprintf(stderr, "Can't register callchain"
+						" params\n");
+				exit(-1);
+			}
 	}
 
 	if (load_kernel() < 0) {
@@ -1974,6 +1981,13 @@ parse_callchain_opt(const struct option *opt __used, const char *arg,
 	else if (!strncmp(tok, "fractal", strlen(arg)))
 		callchain_param.mode = CHAIN_GRAPH_REL;
 
+	else if (!strncmp(tok, "none", strlen(arg))) {
+		callchain_param.mode = CHAIN_NONE;
+		callchain = 0;
+
+		return 0;
+	}
+
 	else
 		return -1;
 
diff --git a/tools/perf/util/callchain.h b/tools/perf/util/callchain.h
index b2d128e07c8..a926ae4f5a1 100644
--- a/tools/perf/util/callchain.h
+++ b/tools/perf/util/callchain.h
@@ -7,6 +7,7 @@
 #include "symbol.h"
 
 enum chain_mode {
+	CHAIN_NONE,
 	CHAIN_FLAT,
 	CHAIN_GRAPH_ABS,
 	CHAIN_GRAPH_REL
-- 
GitLab


From 25446036cbfc2c89faacdb4fb4603943d2197dc6 Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Sat, 8 Aug 2009 02:16:25 +0200
Subject: [PATCH 0700/1153] perf tools: callchain: Fix sum of percentages to be
 100% by displaying amount of ignored chains in fractal mode

When we filter the callchains below a given percentage, we
ignore them and the end result only shows entries that have an
upper percentage than the filter threshold.

It seems to users then that we have an imbalance in the
percentage, as if the sum inside a profiled branch doesn't
reach 100%.

Since in the past there have been real perf report bugs that
showed the same sypmtom, it would be nice to assure the user
that the data is perfect and trustable and it all sums up to
100.00%.

So fix this by displaying the remaining hits that have been
filtered but without more detail than their amount in each
branches. Example while filtering below 50%:

7.73%  [k] delay_tsc
                |
                |--98.22%-- __const_udelay
                |          |
                |          |--86.37%-- ath5k_hw_register_timeout
                |          |          ath5k_hw_noise_floor_calibration
                |          |          ath5k_hw_reset
                |          |          ath5k_reset
                |          |          ath5k_config
                |          |          ieee80211_hw_config
                |          |          |
                |          |          |--88.53%-- ieee80211_scan_work
                |          |          |          worker_thread
                |          |          |          kthread
                |          |          |          child_rip
                |          |           --11.47%-- [...]
                |           --13.63%-- [...]
                 --1.78%-- [...]

Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1249690585-9145-4-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-report.c | 47 ++++++++++++++++++++++++++++++++++---
 1 file changed, 44 insertions(+), 3 deletions(-)

diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index c4a8e108e52..99274cec0ad 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -891,6 +891,21 @@ ipchain__fprintf_graph(FILE *fp, struct callchain_list *chain, int depth,
 	return ret;
 }
 
+static struct symbol *rem_sq_bracket;
+static struct callchain_list rem_hits;
+
+static void init_rem_hits(void)
+{
+	rem_sq_bracket = malloc(sizeof(*rem_sq_bracket) + 6);
+	if (!rem_sq_bracket) {
+		fprintf(stderr, "Not enough memory to display remaining hits\n");
+		return;
+	}
+
+	strcpy(rem_sq_bracket->name, "[...]");
+	rem_hits.sym = rem_sq_bracket;
+}
+
 static size_t
 callchain__fprintf_graph(FILE *fp, struct callchain_node *self,
 			u64 total_samples, int depth, int depth_mask)
@@ -900,6 +915,7 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self,
 	struct callchain_list *chain;
 	int new_depth_mask = depth_mask;
 	u64 new_total;
+	u64 remaining;
 	size_t ret = 0;
 	int i;
 
@@ -908,17 +924,25 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self,
 	else
 		new_total = total_samples;
 
+	remaining = new_total;
+
 	node = rb_first(&self->rb_root);
 	while (node) {
+		u64 cumul;
+
 		child = rb_entry(node, struct callchain_node, rb_node);
+		cumul = cumul_hits(child);
+		remaining -= cumul;
 
 		/*
 		 * The depth mask manages the output of pipes that show
 		 * the depth. We don't want to keep the pipes of the current
-		 * level for the last child of this depth
+		 * level for the last child of this depth.
+		 * Except if we have remaining filtered hits. They will
+		 * supersede the last child
 		 */
 		next = rb_next(node);
-		if (!next)
+		if (!next && (callchain_param.mode != CHAIN_GRAPH_REL || !remaining))
 			new_depth_mask &= ~(1 << (depth - 1));
 
 		/*
@@ -933,7 +957,7 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self,
 			ret += ipchain__fprintf_graph(fp, chain, depth,
 						      new_depth_mask, i++,
 						      new_total,
-						      cumul_hits(child));
+						      cumul);
 		}
 		ret += callchain__fprintf_graph(fp, child, new_total,
 						depth + 1,
@@ -941,6 +965,19 @@ callchain__fprintf_graph(FILE *fp, struct callchain_node *self,
 		node = next;
 	}
 
+	if (callchain_param.mode == CHAIN_GRAPH_REL &&
+		remaining && remaining != new_total) {
+
+		if (!rem_sq_bracket)
+			return ret;
+
+		new_depth_mask &= ~(1 << (depth - 1));
+
+		ret += ipchain__fprintf_graph(fp, &rem_hits, depth,
+					      new_depth_mask, 0, new_total,
+					      remaining);
+	}
+
 	return ret;
 }
 
@@ -1361,6 +1398,8 @@ static size_t output__fprintf(FILE *fp, u64 total_samples)
 	unsigned int width;
 	char *col_width = col_width_list_str;
 
+	init_rem_hits();
+
 	fprintf(fp, "# Samples: %Ld\n", (u64)total_samples);
 	fprintf(fp, "#\n");
 
@@ -1432,6 +1471,8 @@ print_entries:
 	}
 	fprintf(fp, "\n");
 
+	free(rem_sq_bracket);
+
 	return ret;
 }
 
-- 
GitLab


From 10b8e3066066708f304e0fc5cfe658e05abf943d Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Sat, 8 Aug 2009 04:26:35 +0200
Subject: [PATCH 0701/1153] perf_counter: Work around gcc warning by
 initializing tracepoint record unconditionally
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Despite that the tracepoint record is always present when the
PERF_SAMPLE_TP_RECORD flag is set, gcc raises a warning,
thinking it might not be initialized:

  kernel/perf_counter.c: In function ‘perf_counter_output’:
  kernel/perf_counter.c:2650: warning: ‘tp’ may be used uninitialized in this function

Then, initialize it to NULL and always check if it's not NULL
before dereference it.

Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1249698400-5441-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 615440ab929..117622cb73a 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -2646,7 +2646,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 		u64 counter;
 	} group_entry;
 	struct perf_callchain_entry *callchain = NULL;
-	struct perf_tracepoint_record *tp;
+	struct perf_tracepoint_record *tp = NULL;
 	int callchain_size = 0;
 	u64 time;
 	struct {
@@ -2717,7 +2717,8 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 
 	if (sample_type & PERF_SAMPLE_TP_RECORD) {
 		tp = data->private;
-		header.size += tp->size;
+		if (tp)
+			header.size += tp->size;
 	}
 
 	ret = perf_output_begin(&handle, counter, header.size, nmi, 1);
@@ -2783,7 +2784,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 		}
 	}
 
-	if (sample_type & PERF_SAMPLE_TP_RECORD)
+	if ((sample_type & PERF_SAMPLE_TP_RECORD) && tp)
 		perf_output_copy(&handle, tp->record, tp->size);
 
 	perf_output_end(&handle);
-- 
GitLab


From 3a43ce68ae1758fa6a839386025ef45acb6baa22 Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Sat, 8 Aug 2009 04:26:37 +0200
Subject: [PATCH 0702/1153] perf_counter: Fix tracepoint sampling to be part of
 generic sampling

Based on Peter's comments, make tracepoint sampling generic
just like all the other sampling bits are. This is a rename
with no code changes:

- PERF_SAMPLE_TP_RECORD to PERF_SAMPLE_RAW
- struct perf_tracepoint_record to perf_raw_record

We want the system in place that transport tracepoints raw
samples events into the perf ring buffer to be generalized and
usable by any type of counter.

Reported-by; Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1249698400-5441-4-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 include/linux/perf_counter.h | 10 +++++-----
 kernel/perf_counter.c        | 20 ++++++++++----------
 2 files changed, 15 insertions(+), 15 deletions(-)

diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h
index a67dd5c5b6d..2aabe43c1d0 100644
--- a/include/linux/perf_counter.h
+++ b/include/linux/perf_counter.h
@@ -121,7 +121,7 @@ enum perf_counter_sample_format {
 	PERF_SAMPLE_CPU				= 1U << 7,
 	PERF_SAMPLE_PERIOD			= 1U << 8,
 	PERF_SAMPLE_STREAM_ID			= 1U << 9,
-	PERF_SAMPLE_TP_RECORD			= 1U << 10,
+	PERF_SAMPLE_RAW				= 1U << 10,
 
 	PERF_SAMPLE_MAX = 1U << 11,		/* non-ABI */
 };
@@ -414,9 +414,9 @@ struct perf_callchain_entry {
 	__u64				ip[PERF_MAX_STACK_DEPTH];
 };
 
-struct perf_tracepoint_record {
-	int				size;
-	char				*record;
+struct perf_raw_record {
+	u32				size;
+	void				*data;
 };
 
 struct task_struct;
@@ -687,7 +687,7 @@ struct perf_sample_data {
 	struct pt_regs			*regs;
 	u64				addr;
 	u64				period;
-	void				*private;
+	struct perf_raw_record		*raw;
 };
 
 extern int perf_counter_overflow(struct perf_counter *counter, int nmi,
diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 117622cb73a..00231054041 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -2646,7 +2646,7 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 		u64 counter;
 	} group_entry;
 	struct perf_callchain_entry *callchain = NULL;
-	struct perf_tracepoint_record *tp = NULL;
+	struct perf_raw_record *raw = NULL;
 	int callchain_size = 0;
 	u64 time;
 	struct {
@@ -2715,10 +2715,10 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 			header.size += sizeof(u64);
 	}
 
-	if (sample_type & PERF_SAMPLE_TP_RECORD) {
-		tp = data->private;
-		if (tp)
-			header.size += tp->size;
+	if (sample_type & PERF_SAMPLE_RAW) {
+		raw = data->raw;
+		if (raw)
+			header.size += raw->size;
 	}
 
 	ret = perf_output_begin(&handle, counter, header.size, nmi, 1);
@@ -2784,8 +2784,8 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 		}
 	}
 
-	if ((sample_type & PERF_SAMPLE_TP_RECORD) && tp)
-		perf_output_copy(&handle, tp->record, tp->size);
+	if ((sample_type & PERF_SAMPLE_RAW) && raw)
+		perf_output_copy(&handle, raw->data, raw->size);
 
 	perf_output_end(&handle);
 }
@@ -3740,15 +3740,15 @@ static const struct pmu perf_ops_task_clock = {
 void perf_tpcounter_event(int event_id, u64 addr, u64 count, void *record,
 			  int entry_size)
 {
-	struct perf_tracepoint_record tp = {
+	struct perf_raw_record raw = {
 		.size = entry_size,
-		.record = record,
+		.data = record,
 	};
 
 	struct perf_sample_data data = {
 		.regs = get_irq_regs(),
 		.addr = addr,
-		.private = &tp,
+		.raw = &raw,
 	};
 
 	if (!data.regs)
-- 
GitLab


From 3a80b4a3539696f4b0574876326860323035a302 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Fri, 7 Aug 2009 19:49:01 +0200
Subject: [PATCH 0703/1153] perf_counter: Fix a race on perf_counter_ctx

While extending perfcounters with BTS hw-tracing, Markus
Metzger managed to trigger this warning:

   [  995.557128] WARNING: at kernel/perf_counter.c:1191 __perf_counter_task_sched_out+0x48/0x6b()

triggers because commit
9f498cc5be7e013d8d6e4c616980ed0ffc8680d2 (perf_counter: Full
task tracing) removed clearing of tsk->perf_counter_ctxp out
from under ctx->lock which introduced a race (against
perf_lock_task_context).

Move it back and deal with the exit notification by explicitly
passing along the former task context.

Reported-by: Markus T Metzger <markus.t.metzger@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1249667341.17467.5.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 30 +++++++++++++++---------------
 1 file changed, 15 insertions(+), 15 deletions(-)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 00231054041..546e62d6294 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -2850,7 +2850,8 @@ perf_counter_read_event(struct perf_counter *counter,
  */
 
 struct perf_task_event {
-	struct task_struct	*task;
+	struct task_struct		*task;
+	struct perf_counter_context	*task_ctx;
 
 	struct {
 		struct perf_event_header	header;
@@ -2910,24 +2911,23 @@ static void perf_counter_task_ctx(struct perf_counter_context *ctx,
 static void perf_counter_task_event(struct perf_task_event *task_event)
 {
 	struct perf_cpu_context *cpuctx;
-	struct perf_counter_context *ctx;
+	struct perf_counter_context *ctx = task_event->task_ctx;
 
 	cpuctx = &get_cpu_var(perf_cpu_context);
 	perf_counter_task_ctx(&cpuctx->ctx, task_event);
 	put_cpu_var(perf_cpu_context);
 
 	rcu_read_lock();
-	/*
-	 * doesn't really matter which of the child contexts the
-	 * events ends up in.
-	 */
-	ctx = rcu_dereference(current->perf_counter_ctxp);
+	if (!ctx)
+		ctx = rcu_dereference(task_event->task->perf_counter_ctxp);
 	if (ctx)
 		perf_counter_task_ctx(ctx, task_event);
 	rcu_read_unlock();
 }
 
-static void perf_counter_task(struct task_struct *task, int new)
+static void perf_counter_task(struct task_struct *task,
+			      struct perf_counter_context *task_ctx,
+			      int new)
 {
 	struct perf_task_event task_event;
 
@@ -2937,8 +2937,9 @@ static void perf_counter_task(struct task_struct *task, int new)
 		return;
 
 	task_event = (struct perf_task_event){
-		.task	= task,
-		.event  = {
+		.task	  = task,
+		.task_ctx = task_ctx,
+		.event    = {
 			.header = {
 				.type = new ? PERF_EVENT_FORK : PERF_EVENT_EXIT,
 				.misc = 0,
@@ -2956,7 +2957,7 @@ static void perf_counter_task(struct task_struct *task, int new)
 
 void perf_counter_fork(struct task_struct *task)
 {
-	perf_counter_task(task, 1);
+	perf_counter_task(task, NULL, 1);
 }
 
 /*
@@ -4310,7 +4311,7 @@ void perf_counter_exit_task(struct task_struct *child)
 	unsigned long flags;
 
 	if (likely(!child->perf_counter_ctxp)) {
-		perf_counter_task(child, 0);
+		perf_counter_task(child, NULL, 0);
 		return;
 	}
 
@@ -4330,6 +4331,7 @@ void perf_counter_exit_task(struct task_struct *child)
 	 * incremented the context's refcount before we do put_ctx below.
 	 */
 	spin_lock(&child_ctx->lock);
+	child->perf_counter_ctxp = NULL;
 	/*
 	 * If this context is a clone; unclone it so it can't get
 	 * swapped to another process while we're removing all
@@ -4343,9 +4345,7 @@ void perf_counter_exit_task(struct task_struct *child)
 	 * won't get any samples after PERF_EVENT_EXIT. We can however still
 	 * get a few PERF_EVENT_READ events.
 	 */
-	perf_counter_task(child, 0);
-
-	child->perf_counter_ctxp = NULL;
+	perf_counter_task(child, child_ctx, 0);
 
 	/*
 	 * We can recurse on the same lock type through:
-- 
GitLab


From c24b513337f06712b8c81eb4f1413d44591dfee7 Mon Sep 17 00:00:00 2001
From: "Carlos R. Mafra" <crmafra2@gmail.com>
Date: Wed, 5 Aug 2009 20:53:34 +0200
Subject: [PATCH 0704/1153] perf: "Longum est iter per praecepta, breve et
 efficax per exempla"

A few examples of how 'perf' can be used, from an e-mail by
Ingo Molnar http://lkml.org/lkml/2009/8/4/346.

Signed-off-by: Carlos R. Mafra <crmafra2@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Valdis.Kletnieks@vt.edu
LKML-Reference: <20090805185334.GA4535@Pilar.aei.mpg.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Documentation/perf-examples.txt | 225 +++++++++++++++++++++
 1 file changed, 225 insertions(+)
 create mode 100644 tools/perf/Documentation/perf-examples.txt

diff --git a/tools/perf/Documentation/perf-examples.txt b/tools/perf/Documentation/perf-examples.txt
new file mode 100644
index 00000000000..8eb6c489fb1
--- /dev/null
+++ b/tools/perf/Documentation/perf-examples.txt
@@ -0,0 +1,225 @@
+
+		------------------------------
+		****** perf by examples ******
+		------------------------------
+
+[ From an e-mail by Ingo Molnar, http://lkml.org/lkml/2009/8/4/346 ]
+
+
+First, discovery/enumeration of available counters can be done via
+'perf list':
+
+titan:~> perf list
+  [...]
+  kmem:kmalloc                             [Tracepoint event]
+  kmem:kmem_cache_alloc                    [Tracepoint event]
+  kmem:kmalloc_node                        [Tracepoint event]
+  kmem:kmem_cache_alloc_node               [Tracepoint event]
+  kmem:kfree                               [Tracepoint event]
+  kmem:kmem_cache_free                     [Tracepoint event]
+  kmem:mm_page_free_direct                 [Tracepoint event]
+  kmem:mm_pagevec_free                     [Tracepoint event]
+  kmem:mm_page_alloc                       [Tracepoint event]
+  kmem:mm_page_alloc_zone_locked           [Tracepoint event]
+  kmem:mm_page_pcpu_drain                  [Tracepoint event]
+  kmem:mm_page_alloc_extfrag               [Tracepoint event]
+
+Then any (or all) of the above event sources can be activated and
+measured. For example the page alloc/free properties of a 'hackbench
+run' are:
+
+ titan:~> perf stat -e kmem:mm_page_pcpu_drain -e kmem:mm_page_alloc
+ -e kmem:mm_pagevec_free -e kmem:mm_page_free_direct ./hackbench 10
+ Time: 0.575
+
+ Performance counter stats for './hackbench 10':
+
+          13857  kmem:mm_page_pcpu_drain
+          27576  kmem:mm_page_alloc
+           6025  kmem:mm_pagevec_free
+          20934  kmem:mm_page_free_direct
+
+    0.613972165  seconds time elapsed
+
+You can observe the statistical properties as well, by using the
+'repeat the workload N times' feature of perf stat:
+
+ titan:~> perf stat --repeat 5 -e kmem:mm_page_pcpu_drain -e
+   kmem:mm_page_alloc -e kmem:mm_pagevec_free -e
+   kmem:mm_page_free_direct ./hackbench 10
+ Time: 0.627
+ Time: 0.644
+ Time: 0.564
+ Time: 0.559
+ Time: 0.626
+
+ Performance counter stats for './hackbench 10' (5 runs):
+
+          12920  kmem:mm_page_pcpu_drain    ( +-   3.359% )
+          25035  kmem:mm_page_alloc         ( +-   3.783% )
+           6104  kmem:mm_pagevec_free       ( +-   0.934% )
+          18376  kmem:mm_page_free_direct   ( +-   4.941% )
+
+    0.643954516  seconds time elapsed   ( +-   2.363% )
+
+Furthermore, these tracepoints can be used to sample the workload as
+well. For example the page allocations done by a 'git gc' can be
+captured the following way:
+
+ titan:~/git> perf record -f -e kmem:mm_page_alloc -c 1 ./git gc
+ Counting objects: 1148, done.
+ Delta compression using up to 2 threads.
+ Compressing objects: 100% (450/450), done.
+ Writing objects: 100% (1148/1148), done.
+ Total 1148 (delta 690), reused 1148 (delta 690)
+ [ perf record: Captured and wrote 0.267 MB perf.data (~11679 samples) ]
+
+To check which functions generated page allocations:
+
+ titan:~/git> perf report
+ # Samples: 10646
+ #
+ # Overhead          Command               Shared Object
+ # ........  ...............  ..........................
+ #
+    23.57%       git-repack  /lib64/libc-2.5.so
+    21.81%              git  /lib64/libc-2.5.so
+    14.59%              git  ./git
+    11.79%       git-repack  ./git
+     7.12%              git  /lib64/ld-2.5.so
+     3.16%       git-repack  /lib64/libpthread-2.5.so
+     2.09%       git-repack  /bin/bash
+     1.97%               rm  /lib64/libc-2.5.so
+     1.39%               mv  /lib64/ld-2.5.so
+     1.37%               mv  /lib64/libc-2.5.so
+     1.12%       git-repack  /lib64/ld-2.5.so
+     0.95%               rm  /lib64/ld-2.5.so
+     0.90%  git-update-serv  /lib64/libc-2.5.so
+     0.73%  git-update-serv  /lib64/ld-2.5.so
+     0.68%             perf  /lib64/libpthread-2.5.so
+     0.64%       git-repack  /usr/lib64/libz.so.1.2.3
+
+Or to see it on a more finegrained level:
+
+titan:~/git> perf report --sort comm,dso,symbol
+# Samples: 10646
+#
+# Overhead          Command               Shared Object  Symbol
+# ........  ...............  ..........................  ......
+#
+     9.35%       git-repack  ./git                       [.] insert_obj_hash
+     9.12%              git  ./git                       [.] insert_obj_hash
+     7.31%              git  /lib64/libc-2.5.so          [.] memcpy
+     6.34%       git-repack  /lib64/libc-2.5.so          [.] _int_malloc
+     6.24%       git-repack  /lib64/libc-2.5.so          [.] memcpy
+     5.82%       git-repack  /lib64/libc-2.5.so          [.] __GI___fork
+     5.47%              git  /lib64/libc-2.5.so          [.] _int_malloc
+     2.99%              git  /lib64/libc-2.5.so          [.] memset
+
+Furthermore, call-graph sampling can be done too, of page
+allocations - to see precisely what kind of page allocations there
+are:
+
+ titan:~/git> perf record -f -g -e kmem:mm_page_alloc -c 1 ./git gc
+ Counting objects: 1148, done.
+ Delta compression using up to 2 threads.
+ Compressing objects: 100% (450/450), done.
+ Writing objects: 100% (1148/1148), done.
+ Total 1148 (delta 690), reused 1148 (delta 690)
+ [ perf record: Captured and wrote 0.963 MB perf.data (~42069 samples) ]
+
+ titan:~/git> perf report -g
+ # Samples: 10686
+ #
+ # Overhead          Command               Shared Object
+ # ........  ...............  ..........................
+ #
+    23.25%       git-repack  /lib64/libc-2.5.so
+                |
+                |--50.00%-- _int_free
+                |
+                |--37.50%-- __GI___fork
+                |          make_child
+                |
+                |--12.50%-- ptmalloc_unlock_all2
+                |          make_child
+                |
+                 --6.25%-- __GI_strcpy
+    21.61%              git  /lib64/libc-2.5.so
+                |
+                |--30.00%-- __GI_read
+                |          |
+                |           --83.33%-- git_config_from_file
+                |                     git_config
+                |                     |
+   [...]
+
+Or you can observe the whole system's page allocations for 10
+seconds:
+
+titan:~/git> perf stat -a -e kmem:mm_page_pcpu_drain -e
+kmem:mm_page_alloc -e kmem:mm_pagevec_free -e
+kmem:mm_page_free_direct sleep 10
+
+ Performance counter stats for 'sleep 10':
+
+         171585  kmem:mm_page_pcpu_drain
+         322114  kmem:mm_page_alloc
+          73623  kmem:mm_pagevec_free
+         254115  kmem:mm_page_free_direct
+
+   10.000591410  seconds time elapsed
+
+Or observe how fluctuating the page allocations are, via statistical
+analysis done over ten 1-second intervals:
+
+ titan:~/git> perf stat --repeat 10 -a -e kmem:mm_page_pcpu_drain -e
+   kmem:mm_page_alloc -e kmem:mm_pagevec_free -e
+   kmem:mm_page_free_direct sleep 1
+
+ Performance counter stats for 'sleep 1' (10 runs):
+
+          17254  kmem:mm_page_pcpu_drain    ( +-   3.709% )
+          34394  kmem:mm_page_alloc         ( +-   4.617% )
+           7509  kmem:mm_pagevec_free       ( +-   4.820% )
+          25653  kmem:mm_page_free_direct   ( +-   3.672% )
+
+    1.058135029  seconds time elapsed   ( +-   3.089% )
+
+Or you can annotate the recorded 'git gc' run on a per symbol basis
+and check which instructions/source-code generated page allocations:
+
+ titan:~/git> perf annotate __GI___fork
+ ------------------------------------------------
+  Percent |      Source code & Disassembly of libc-2.5.so
+ ------------------------------------------------
+          :
+          :
+          :      Disassembly of section .plt:
+          :      Disassembly of section .text:
+          :
+          :      00000031a2e95560 <__fork>:
+ [...]
+     0.00 :        31a2e95602:   b8 38 00 00 00          mov    $0x38,%eax
+     0.00 :        31a2e95607:   0f 05                   syscall
+    83.42 :        31a2e95609:   48 3d 00 f0 ff ff       cmp    $0xfffffffffffff000,%rax
+     0.00 :        31a2e9560f:   0f 87 4d 01 00 00       ja     31a2e95762 <__fork+0x202>
+     0.00 :        31a2e95615:   85 c0                   test   %eax,%eax
+
+( this shows that 83.42% of __GI___fork's page allocations come from
+  the 0x38 system call it performs. )
+
+etc. etc. - a lot more is possible. I could list a dozen of
+other different usecases straight away - neither of which is
+possible via /proc/vmstat.
+
+/proc/vmstat is not in the same league really, in terms of
+expressive power of system analysis and performance
+analysis.
+
+All that the above results needed were those new tracepoints
+in include/tracing/events/kmem.h.
+
+	Ingo
+
+
-- 
GitLab


From 183f3b0887083d36c8a25cd5e3518906415d1889 Mon Sep 17 00:00:00 2001
From: Mike Galbraith <efault@gmx.de>
Date: Sat, 8 Aug 2009 14:14:15 +0200
Subject: [PATCH 0705/1153] perf_counter tools: Fix libbfd detection for
 systems with libz dependency

Due to a libz dependency in some distro's binutils package,
C++ demangle support isn't compiled in despite the necessary
libraries being available.

Fix this by adding a -lz link test to the dependency detection
rules.

Signed-off-by: Mike Galbraith <efault@gmx.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1249733655.6929.5.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Makefile | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/tools/perf/Makefile b/tools/perf/Makefile
index 1916e44b9bb..60411e94113 100644
--- a/tools/perf/Makefile
+++ b/tools/perf/Makefile
@@ -387,10 +387,14 @@ else
 
 	has_bfd_iberty := $(shell sh -c "(echo '\#include <bfd.h>'; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty > /dev/null 2>&1 && echo y")
 
+	has_bfd_iberty_z := $(shell sh -c "(echo '\#include <bfd.h>'; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty -lz > /dev/null 2>&1 && echo y")
+
 	ifeq ($(has_bfd),y)
 		EXTLIBS += -lbfd
 	else ifeq ($(has_bfd_iberty),y)
 		EXTLIBS += -lbfd -liberty
+	else ifeq ($(has_bfd_iberty_z),y)
+		EXTLIBS += -lbfd -liberty -lz
 	else
 		msg := $(warning No bfd.h/libbfd found, install binutils-dev[el] to gain symbol demangling)
 		BASIC_CFLAGS += -DNO_DEMANGLE
-- 
GitLab


From c0a8865e32c8d1a562db38e06ef31ef23282f646 Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Sun, 9 Aug 2009 04:19:15 +0200
Subject: [PATCH 0706/1153] perf tools: callchain: Fix bad rounding of minimum
 rate

Sometimes we get callchain branches that have a rate under the
limit given by the user.

Say you launched:

 perf record -f -g -a ./hackbench 10
 perf report -g fractal,10.0

And you got:

2.33%       hackbench  [kernel]                  [k] _spin_lock_irqsave
                |
                |--78.57%-- remove_wait_queue
                |          poll_freewait
                |          do_sys_poll
                |          sys_poll
                |          sysenter_dispatch
                |          0xf7ffa430
                |          0x1ffadea3c
                |
                |--7.14%-- __up_read
                |          up_read
                |          do_page_fault
                |          page_fault
                |          0xf7ffa430
                |          0xa0df710000000a
                ...

It is abnormal to get a 7.14% branch whereas we passed a 10%
filter.

The problem is that we round down the minimum threshold. This
happens mostly when we have very low number of events. If the
total amount of your branch is 4 and you have a subranch of 3
events, filtering to 90% will be computed like follows:

  limit = 4 * 0.9;

The result is about 3.6, but the cast to integer will round
down to 3. It means that our filter is actually of 75%

We must then explicitly round up the minimum threshold.

Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: acme@redhat.com
Cc: peterz@infradead.org
Cc: efault@gmx.de
LKML-Reference: <20090809024235.GA10146@nowhere>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/util/callchain.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/tools/perf/util/callchain.c b/tools/perf/util/callchain.c
index a8e67aa9ef4..01147341164 100644
--- a/tools/perf/util/callchain.c
+++ b/tools/perf/util/callchain.c
@@ -13,6 +13,7 @@
 #include <stdio.h>
 #include <stdbool.h>
 #include <errno.h>
+#include <math.h>
 
 #include "callchain.h"
 
@@ -112,7 +113,7 @@ static void __sort_chain_graph_rel(struct callchain_node *node,
 	u64 min_hit;
 
 	node->rb_root = RB_ROOT;
-	min_hit = node->children_hit * min_percent / 100.0;
+	min_hit = ceil(node->children_hit * min_percent);
 
 	chain_for_each_child(child, node) {
 		__sort_chain_graph_rel(child, min_percent);
@@ -126,7 +127,7 @@ static void
 sort_chain_graph_rel(struct rb_root *rb_root, struct callchain_node *chain_root,
 		     u64 min_hit __used, struct callchain_param *param)
 {
-	__sort_chain_graph_rel(chain_root, param->min_percent);
+	__sort_chain_graph_rel(chain_root, param->min_percent / 100.0);
 	rb_root->rb_node = chain_root->rb_root.rb_node;
 }
 
-- 
GitLab


From c8c00a6915a2e3d10416e8bdd3138429beb96210 Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Mon, 10 Aug 2009 12:50:52 +1000
Subject: [PATCH 0707/1153] Remove deadlock potential in md_open

A recent commit:
  commit 449aad3e25358812c43afc60918c5ad3819488e7

introduced the possibility of an A-B/B-A deadlock between
bd_mutex and reconfig_mutex.

__blkdev_get holds bd_mutex while calling md_open which takes
   reconfig_mutex,
do_md_run is always called with reconfig_mutex held, and it now
   takes bd_mutex in the call the revalidate_disk.

This potential deadlock was not caught by lockdep due to the
use of mutex_lock_interruptible_nexted which was introduced
by
   commit d63a5a74dee87883fda6b7d170244acaac5b05e8
do avoid a warning of an impossible deadlock.

It is quite possible to split reconfig_mutex in to two locks.
One protects the array data structures while it is being
reconfigured, the other ensures that an array is never even partially
open while it is being deactivated.
In particular, the second lock prevents an open from completing
between the time when do_md_stop checks if there are any active opens,
and the time when the array is either set read-only, or when ->pers is
set to NULL.  So we can be certain that no IO is in flight as the
array is being destroyed.

So create a new lock, open_mutex, just to ensure exclusion between
'open' and 'stop'.

This avoids the deadlock and also avoids the lockdep warning mentioned
in commit d63a5a74d

Reported-by: "Mike Snitzer" <snitzer@gmail.com>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/md.c | 18 ++++++++++--------
 drivers/md/md.h | 10 ++++++++++
 2 files changed, 20 insertions(+), 8 deletions(-)

diff --git a/drivers/md/md.c b/drivers/md/md.c
index 5b98bea4ff9..5614500092e 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -359,6 +359,7 @@ static mddev_t * mddev_find(dev_t unit)
 	else
 		new->md_minor = MINOR(unit) >> MdpMinorShift;
 
+	mutex_init(&new->open_mutex);
 	mutex_init(&new->reconfig_mutex);
 	INIT_LIST_HEAD(&new->disks);
 	INIT_LIST_HEAD(&new->all_mddevs);
@@ -4304,12 +4305,11 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open)
 	struct gendisk *disk = mddev->gendisk;
 	mdk_rdev_t *rdev;
 
+	mutex_lock(&mddev->open_mutex);
 	if (atomic_read(&mddev->openers) > is_open) {
 		printk("md: %s still in use.\n",mdname(mddev));
-		return -EBUSY;
-	}
-
-	if (mddev->pers) {
+		err = -EBUSY;
+	} else if (mddev->pers) {
 
 		if (mddev->sync_thread) {
 			set_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
@@ -4367,7 +4367,10 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open)
 			set_disk_ro(disk, 1);
 		clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
 	}
-
+out:
+	mutex_unlock(&mddev->open_mutex);
+	if (err)
+		return err;
 	/*
 	 * Free resources if final stop
 	 */
@@ -4433,7 +4436,6 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open)
 	blk_integrity_unregister(disk);
 	md_new_event(mddev);
 	sysfs_notify_dirent(mddev->sysfs_state);
-out:
 	return err;
 }
 
@@ -5518,12 +5520,12 @@ static int md_open(struct block_device *bdev, fmode_t mode)
 	}
 	BUG_ON(mddev != bdev->bd_disk->private_data);
 
-	if ((err = mutex_lock_interruptible_nested(&mddev->reconfig_mutex, 1)))
+	if ((err = mutex_lock_interruptible(&mddev->open_mutex)))
 		goto out;
 
 	err = 0;
 	atomic_inc(&mddev->openers);
-	mddev_unlock(mddev);
+	mutex_unlock(&mddev->open_mutex);
 
 	check_disk_change(bdev);
  out:
diff --git a/drivers/md/md.h b/drivers/md/md.h
index 78f03168baf..f8fc188bc76 100644
--- a/drivers/md/md.h
+++ b/drivers/md/md.h
@@ -223,6 +223,16 @@ struct mddev_s
 							    * so we don't loop trying */
 
 	int				in_sync;	/* know to not need resync */
+	/* 'open_mutex' avoids races between 'md_open' and 'do_md_stop', so
+	 * that we are never stopping an array while it is open.
+	 * 'reconfig_mutex' protects all other reconfiguration.
+	 * These locks are separate due to conflicting interactions
+	 * with bdev->bd_mutex.
+	 * Lock ordering is:
+	 *  reconfig_mutex -> bd_mutex : e.g. do_md_run -> revalidate_disk
+	 *  bd_mutex -> open_mutex:  e.g. __blkdev_get -> md_open
+	 */
+	struct mutex			open_mutex;
 	struct mutex			reconfig_mutex;
 	atomic_t			active;		/* general refcount */
 	atomic_t			openers;	/* number of active opens */
-- 
GitLab


From cb2f33e9596632979c140c243ac1e8e994f62180 Mon Sep 17 00:00:00 2001
From: Chris Snook <chris.snook@gmail.com>
Date: Thu, 6 Aug 2009 12:19:31 +0000
Subject: [PATCH 0708/1153] MAINTAINERS: update atlx contact info

Update MAINTAINERS to reflect my current (non-)affiliation.  Anyone
hiring?

Signed-off-by: Chris Snook <chris.snook@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 MAINTAINERS | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index b1114cfac6b..fa76ad0a37e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -904,7 +904,7 @@ F:	drivers/input/misc/ati_remote2.c
 
 ATLX ETHERNET DRIVERS
 M:	Jay Cliburn <jcliburn@gmail.com>
-M:	Chris Snook <csnook@redhat.com>
+M:	Chris Snook <chris.snook@gmail.com>
 M:	Jie Yang <jie.yang@atheros.com>
 L:	atl1-devel@lists.sourceforge.net
 W:	http://sourceforge.net/projects/atl1
-- 
GitLab


From 5d5ceb8bdde403529ad9849f300dc80b1884550f Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Thu, 6 Aug 2009 13:06:03 +0000
Subject: [PATCH 0709/1153] irda: fix read buffer overflow

io[i] is read before the bounds check on i, order should be reversed.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/irda/w83977af_ir.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/irda/w83977af_ir.c b/drivers/net/irda/w83977af_ir.c
index d0883835b0c..fe4f2b2bff9 100644
--- a/drivers/net/irda/w83977af_ir.c
+++ b/drivers/net/irda/w83977af_ir.c
@@ -115,7 +115,7 @@ static int __init w83977af_init(void)
 
 	IRDA_DEBUG(0, "%s()\n", __func__ );
 
-	for (i=0; (io[i] < 2000) && (i < ARRAY_SIZE(dev_self)); i++) {
+	for (i=0; i < ARRAY_SIZE(dev_self) && io[i] < 2000; i++) {
 		if (w83977af_open(i, io[i], irq[i], dma[i]) == 0)
 			return 0;
 	}
-- 
GitLab


From 082ba88a5e6b1425abed3fae4ad65e0e985ed081 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Thu, 6 Aug 2009 13:06:56 +0000
Subject: [PATCH 0710/1153] atlx: strncpy does not null terminate string

strlcpy() will always null terminate the string.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <csnook@redhat.com>
Cc: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/atl1c/atl1c_ethtool.c | 8 ++++----
 drivers/net/atlx/atl1.c           | 8 ++++----
 2 files changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/net/atl1c/atl1c_ethtool.c b/drivers/net/atl1c/atl1c_ethtool.c
index 607007d75b6..00d11b480af 100644
--- a/drivers/net/atl1c/atl1c_ethtool.c
+++ b/drivers/net/atl1c/atl1c_ethtool.c
@@ -232,11 +232,11 @@ static void atl1c_get_drvinfo(struct net_device *netdev,
 {
 	struct atl1c_adapter *adapter = netdev_priv(netdev);
 
-	strncpy(drvinfo->driver,  atl1c_driver_name, sizeof(drvinfo->driver));
-	strncpy(drvinfo->version, atl1c_driver_version,
+	strlcpy(drvinfo->driver,  atl1c_driver_name, sizeof(drvinfo->driver));
+	strlcpy(drvinfo->version, atl1c_driver_version,
 		sizeof(drvinfo->version));
-	strncpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version));
-	strncpy(drvinfo->bus_info, pci_name(adapter->pdev),
+	strlcpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version));
+	strlcpy(drvinfo->bus_info, pci_name(adapter->pdev),
 		sizeof(drvinfo->bus_info));
 	drvinfo->n_stats = 0;
 	drvinfo->testinfo_len = 0;
diff --git a/drivers/net/atlx/atl1.c b/drivers/net/atlx/atl1.c
index 94d7325caf4..8bca12f7139 100644
--- a/drivers/net/atlx/atl1.c
+++ b/drivers/net/atlx/atl1.c
@@ -3378,11 +3378,11 @@ static void atl1_get_drvinfo(struct net_device *netdev,
 {
 	struct atl1_adapter *adapter = netdev_priv(netdev);
 
-	strncpy(drvinfo->driver, ATLX_DRIVER_NAME, sizeof(drvinfo->driver));
-	strncpy(drvinfo->version, ATLX_DRIVER_VERSION,
+	strlcpy(drvinfo->driver, ATLX_DRIVER_NAME, sizeof(drvinfo->driver));
+	strlcpy(drvinfo->version, ATLX_DRIVER_VERSION,
 		sizeof(drvinfo->version));
-	strncpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version));
-	strncpy(drvinfo->bus_info, pci_name(adapter->pdev),
+	strlcpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version));
+	strlcpy(drvinfo->bus_info, pci_name(adapter->pdev),
 		sizeof(drvinfo->bus_info));
 	drvinfo->eedump_len = ATL1_EEDUMP_LEN;
 }
-- 
GitLab


From b79a79471bd31d737c939a6ddc347417047b4320 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Jussi=20M=C3=A4ki?= <joamaki@gmail.com>
Date: Thu, 6 Aug 2009 21:38:14 +0000
Subject: [PATCH 0711/1153] Fix xfrm hash collisions by changing
 __xfrm4_daddr_saddr_hash to hash addresses with addition

This patch fixes hash collisions in cases where number
of entries have incrementing IP source and destination addresses
from single respective subnets (i.e. 192.168.0.1-172.16.0.1,
192.168.0.2-172.16.0.2, and so on.).

Signed-off-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/xfrm/xfrm_hash.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/xfrm/xfrm_hash.h b/net/xfrm/xfrm_hash.h
index d401dc8f05e..e5195c99f71 100644
--- a/net/xfrm/xfrm_hash.h
+++ b/net/xfrm/xfrm_hash.h
@@ -16,7 +16,7 @@ static inline unsigned int __xfrm6_addr_hash(xfrm_address_t *addr)
 
 static inline unsigned int __xfrm4_daddr_saddr_hash(xfrm_address_t *daddr, xfrm_address_t *saddr)
 {
-	return ntohl(daddr->a4 ^ saddr->a4);
+	return ntohl(daddr->a4 + saddr->a4);
 }
 
 static inline unsigned int __xfrm6_daddr_saddr_hash(xfrm_address_t *daddr, xfrm_address_t *saddr)
-- 
GitLab


From e84b90ae5eb3c112d1f208964df1d8156a538289 Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Thu, 6 Aug 2009 20:27:04 +0000
Subject: [PATCH 0712/1153] can: Fix raw_getname() leak

raw_getname() can leak 10 bytes of kernel memory to user

(two bytes hole between can_family and can_ifindex,
8 bytes at the end of sockaddr_can structure)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/can/raw.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/can/raw.c b/net/can/raw.c
index f4cc44548bd..db3152df7d2 100644
--- a/net/can/raw.c
+++ b/net/can/raw.c
@@ -401,6 +401,7 @@ static int raw_getname(struct socket *sock, struct sockaddr *uaddr,
 	if (peer)
 		return -EOPNOTSUPP;
 
+	memset(addr, 0, sizeof(*addr));
 	addr->can_family  = AF_CAN;
 	addr->can_ifindex = ro->ifindex;
 
-- 
GitLab


From 9555b31e8c29d2000e1e1f569f6f242ebd596e47 Mon Sep 17 00:00:00 2001
From: Greg Ungerer <gerg@snapgear.com>
Date: Thu, 6 Aug 2009 17:58:18 +0000
Subject: [PATCH 0713/1153] fec: fix FEC driver packet transmission breakage

Commit f0b3fbeae11a526c3d308b691684589ee37c359b ("FEC Buffer rework")
breaks transmission of packets where the skb data buffer is not memory
aligned according to FEC_ALIGNMENT. It incorrectly passes to
dma_sync_single() the buffer address directly from the skb, instead of
the address calculated for use (which may be the skb address or one of
the bounce buffers).

It seems there is no use converting the cpu address of the buffer to
a physical either, since dma_map_single() expects the cpu address and
will return the dma address to use in the descriptor. So remove the use
of __pa() on the buffer address as well.

This patch is against 2.6.30-rc5. This breakage is a regression over
2.6.30, which does not have this problem.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/fec.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/net/fec.c b/drivers/net/fec.c
index d4b98074b1b..c9fd82d3a80 100644
--- a/drivers/net/fec.c
+++ b/drivers/net/fec.c
@@ -285,6 +285,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 	struct fec_enet_private *fep = netdev_priv(dev);
 	struct bufdesc *bdp;
+	void *bufaddr;
 	unsigned short	status;
 	unsigned long flags;
 
@@ -312,7 +313,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	status &= ~BD_ENET_TX_STATS;
 
 	/* Set buffer length and buffer pointer */
-	bdp->cbd_bufaddr = __pa(skb->data);
+	bufaddr = skb->data;
 	bdp->cbd_datlen = skb->len;
 
 	/*
@@ -320,11 +321,11 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	 * 4-byte boundaries. Use bounce buffers to copy data
 	 * and get it aligned. Ugh.
 	 */
-	if (bdp->cbd_bufaddr & FEC_ALIGNMENT) {
+	if (((unsigned long) bufaddr) & FEC_ALIGNMENT) {
 		unsigned int index;
 		index = bdp - fep->tx_bd_base;
 		memcpy(fep->tx_bounce[index], (void *)skb->data, skb->len);
-		bdp->cbd_bufaddr = __pa(fep->tx_bounce[index]);
+		bufaddr = fep->tx_bounce[index];
 	}
 
 	/* Save skb pointer */
@@ -336,7 +337,7 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	/* Push the data cache so the CPM does not get stale memory
 	 * data.
 	 */
-	bdp->cbd_bufaddr = dma_map_single(&dev->dev, skb->data,
+	bdp->cbd_bufaddr = dma_map_single(&dev->dev, bufaddr,
 			FEC_ENET_TX_FRSIZE, DMA_TO_DEVICE);
 
 	/* Send it on its way.  Tell FEC it's ready, interrupt when done,
-- 
GitLab


From 876bfd4d0f18cd1f698249870c7e7fb944de1c26 Mon Sep 17 00:00:00 2001
From: Herbert Xu <herbert@gondor.apana.org.au>
Date: Thu, 6 Aug 2009 14:22:44 +0000
Subject: [PATCH 0714/1153] tun: Extend RTNL lock coverage over whole ioctl

As it is, parts of the ioctl runs under the RTNL and parts of
it do not.  The unlocked section is still protected by the BKL,
but there can be subtle races.  For example, Eric Biederman and
Paul Moore observed that if two threads tried to create two tun
devices on the same file descriptor, then unexpected results
may occur.

As there isn't anything in the ioctl that is expected to sleep
indefinitely, we can prevent this from occurring by extending
the RTNL lock coverage.

This also allows to get rid of the BKL.

Finally, I changed tun_get_iff to take a tun device in order to
avoid calling tun_put which would dead-lock as it also tries to
take the RTNL lock.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/tun.c | 50 ++++++++++++++++++-----------------------------
 1 file changed, 19 insertions(+), 31 deletions(-)

diff --git a/drivers/net/tun.c b/drivers/net/tun.c
index 027f7aba26a..42b6c6319bc 100644
--- a/drivers/net/tun.c
+++ b/drivers/net/tun.c
@@ -1048,20 +1048,15 @@ static int tun_set_iff(struct net *net, struct file *file, struct ifreq *ifr)
 	return err;
 }
 
-static int tun_get_iff(struct net *net, struct file *file, struct ifreq *ifr)
+static int tun_get_iff(struct net *net, struct tun_struct *tun,
+		       struct ifreq *ifr)
 {
-	struct tun_struct *tun = tun_get(file);
-
-	if (!tun)
-		return -EBADFD;
-
 	DBG(KERN_INFO "%s: tun_get_iff\n", tun->dev->name);
 
 	strcpy(ifr->ifr_name, tun->dev->name);
 
 	ifr->ifr_flags = tun_flags(tun);
 
-	tun_put(tun);
 	return 0;
 }
 
@@ -1105,8 +1100,8 @@ static int set_offload(struct net_device *dev, unsigned long arg)
 	return 0;
 }
 
-static int tun_chr_ioctl(struct inode *inode, struct file *file,
-			 unsigned int cmd, unsigned long arg)
+static long tun_chr_ioctl(struct file *file, unsigned int cmd,
+			  unsigned long arg)
 {
 	struct tun_file *tfile = file->private_data;
 	struct tun_struct *tun;
@@ -1128,34 +1123,32 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file,
 				(unsigned int __user*)argp);
 	}
 
+	rtnl_lock();
+
 	tun = __tun_get(tfile);
 	if (cmd == TUNSETIFF && !tun) {
-		int err;
-
 		ifr.ifr_name[IFNAMSIZ-1] = '\0';
 
-		rtnl_lock();
-		err = tun_set_iff(tfile->net, file, &ifr);
-		rtnl_unlock();
+		ret = tun_set_iff(tfile->net, file, &ifr);
 
-		if (err)
-			return err;
+		if (ret)
+			goto unlock;
 
 		if (copy_to_user(argp, &ifr, sizeof(ifr)))
-			return -EFAULT;
-		return 0;
+			ret = -EFAULT;
+		goto unlock;
 	}
 
-
+	ret = -EBADFD;
 	if (!tun)
-		return -EBADFD;
+		goto unlock;
 
 	DBG(KERN_INFO "%s: tun_chr_ioctl cmd %d\n", tun->dev->name, cmd);
 
 	ret = 0;
 	switch (cmd) {
 	case TUNGETIFF:
-		ret = tun_get_iff(current->nsproxy->net_ns, file, &ifr);
+		ret = tun_get_iff(current->nsproxy->net_ns, tun, &ifr);
 		if (ret)
 			break;
 
@@ -1201,7 +1194,6 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file,
 
 	case TUNSETLINK:
 		/* Only allow setting the type when the interface is down */
-		rtnl_lock();
 		if (tun->dev->flags & IFF_UP) {
 			DBG(KERN_INFO "%s: Linktype set failed because interface is up\n",
 				tun->dev->name);
@@ -1211,7 +1203,6 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file,
 			DBG(KERN_INFO "%s: linktype set to %d\n", tun->dev->name, tun->dev->type);
 			ret = 0;
 		}
-		rtnl_unlock();
 		break;
 
 #ifdef TUN_DEBUG
@@ -1220,9 +1211,7 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file,
 		break;
 #endif
 	case TUNSETOFFLOAD:
-		rtnl_lock();
 		ret = set_offload(tun->dev, arg);
-		rtnl_unlock();
 		break;
 
 	case TUNSETTXFILTER:
@@ -1230,9 +1219,7 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file,
 		ret = -EINVAL;
 		if ((tun->flags & TUN_TYPE_MASK) != TUN_TAP_DEV)
 			break;
-		rtnl_lock();
 		ret = update_filter(&tun->txflt, (void __user *)arg);
-		rtnl_unlock();
 		break;
 
 	case SIOCGIFHWADDR:
@@ -1248,9 +1235,7 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file,
 		DBG(KERN_DEBUG "%s: set hw address: %pM\n",
 			tun->dev->name, ifr.ifr_hwaddr.sa_data);
 
-		rtnl_lock();
 		ret = dev_set_mac_address(tun->dev, &ifr.ifr_hwaddr);
-		rtnl_unlock();
 		break;
 
 	case TUNGETSNDBUF:
@@ -1273,7 +1258,10 @@ static int tun_chr_ioctl(struct inode *inode, struct file *file,
 		break;
 	};
 
-	tun_put(tun);
+unlock:
+	rtnl_unlock();
+	if (tun)
+		tun_put(tun);
 	return ret;
 }
 
@@ -1361,7 +1349,7 @@ static const struct file_operations tun_fops = {
 	.write = do_sync_write,
 	.aio_write = tun_chr_aio_write,
 	.poll	= tun_chr_poll,
-	.ioctl	= tun_chr_ioctl,
+	.unlocked_ioctl = tun_chr_ioctl,
 	.open	= tun_chr_open,
 	.release = tun_chr_close,
 	.fasync = tun_chr_fasync
-- 
GitLab


From a6616b42fbc39c1ccc2373996f1441ce7707ea93 Mon Sep 17 00:00:00 2001
From: Yi Zou <yi.zou@intel.com>
Date: Thu, 6 Aug 2009 13:05:23 +0000
Subject: [PATCH 0715/1153] ixgbe: Pass rx_ring directly in
 ixgbe_configure_srrctl()

Instead of passing the register index of the corresponding rx_ring and find
the way back to get to corresponding rx_ring in ixgbe_configure_srrctl(),
simplify the function ixgbe_configure_srrctl() by passing the rx_ring into
it. Then the register index for that rx_ring is already available from
rx_ring->reg_idx.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ixgbe/ixgbe_main.c | 55 ++++++++++------------------------
 1 file changed, 15 insertions(+), 40 deletions(-)

diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index 110c65ab5cb..e361b7f0101 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -1898,46 +1898,19 @@ static void ixgbe_configure_tx(struct ixgbe_adapter *adapter)
 
 #define IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT 2
 
-static void ixgbe_configure_srrctl(struct ixgbe_adapter *adapter, int index)
+static void ixgbe_configure_srrctl(struct ixgbe_adapter *adapter,
+                                   struct ixgbe_ring *rx_ring)
 {
-	struct ixgbe_ring *rx_ring;
 	u32 srrctl;
-	int queue0 = 0;
-	unsigned long mask;
+	int index;
 	struct ixgbe_ring_feature *feature = adapter->ring_feature;
 
-	if (adapter->hw.mac.type == ixgbe_mac_82599EB) {
-		if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) {
-			int dcb_i = feature[RING_F_DCB].indices;
-			if (dcb_i == 8)
-				queue0 = index >> 4;
-			else if (dcb_i == 4)
-				queue0 = index >> 5;
-			else
-				dev_err(&adapter->pdev->dev, "Invalid DCB "
-				        "configuration\n");
-#ifdef IXGBE_FCOE
-			if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) {
-				struct ixgbe_ring_feature *f;
-
-				rx_ring = &adapter->rx_ring[queue0];
-				f = &adapter->ring_feature[RING_F_FCOE];
-				if ((queue0 == 0) && (index > rx_ring->reg_idx))
-					queue0 = f->mask + index -
-					         rx_ring->reg_idx - 1;
-			}
-#endif /* IXGBE_FCOE */
-		} else {
-			queue0 = index;
-		}
-	} else {
+	index = rx_ring->reg_idx;
+	if (adapter->hw.mac.type == ixgbe_mac_82598EB) {
+		unsigned long mask;
 		mask = (unsigned long) feature[RING_F_RSS].mask;
-		queue0 = index & mask;
 		index = index & mask;
 	}
-
-	rx_ring = &adapter->rx_ring[queue0];
-
 	srrctl = IXGBE_READ_REG(&adapter->hw, IXGBE_SRRCTL(index));
 
 	srrctl &= ~IXGBE_SRRCTL_BSIZEHDR_MASK;
@@ -2002,6 +1975,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 {
 	u64 rdba;
 	struct ixgbe_hw *hw = &adapter->hw;
+	struct ixgbe_ring *rx_ring;
 	struct net_device *netdev = adapter->netdev;
 	int max_frame = netdev->mtu + ETH_HLEN + ETH_FCS_LEN;
 	int i, j;
@@ -2070,16 +2044,17 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 	 * the Base and Length of the Rx Descriptor Ring
 	 */
 	for (i = 0; i < adapter->num_rx_queues; i++) {
-		rdba = adapter->rx_ring[i].dma;
-		j = adapter->rx_ring[i].reg_idx;
+		rx_ring = &adapter->rx_ring[i];
+		rdba = rx_ring->dma;
+		j = rx_ring->reg_idx;
 		IXGBE_WRITE_REG(hw, IXGBE_RDBAL(j), (rdba & DMA_BIT_MASK(32)));
 		IXGBE_WRITE_REG(hw, IXGBE_RDBAH(j), (rdba >> 32));
 		IXGBE_WRITE_REG(hw, IXGBE_RDLEN(j), rdlen);
 		IXGBE_WRITE_REG(hw, IXGBE_RDH(j), 0);
 		IXGBE_WRITE_REG(hw, IXGBE_RDT(j), 0);
-		adapter->rx_ring[i].head = IXGBE_RDH(j);
-		adapter->rx_ring[i].tail = IXGBE_RDT(j);
-		adapter->rx_ring[i].rx_buf_len = rx_buf_len;
+		rx_ring->head = IXGBE_RDH(j);
+		rx_ring->tail = IXGBE_RDT(j);
+		rx_ring->rx_buf_len = rx_buf_len;
 
 #ifdef IXGBE_FCOE
 		if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) {
@@ -2087,12 +2062,12 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 			f = &adapter->ring_feature[RING_F_FCOE];
 			if ((rx_buf_len < IXGBE_FCOE_JUMBO_FRAME_SIZE) &&
 			    (i >= f->mask) && (i < f->mask + f->indices))
-				adapter->rx_ring[i].rx_buf_len =
+				rx_ring->rx_buf_len =
 				        IXGBE_FCOE_JUMBO_FRAME_SIZE;
 		}
 
 #endif /* IXGBE_FCOE */
-		ixgbe_configure_srrctl(adapter, j);
+		ixgbe_configure_srrctl(adapter, rx_ring);
 	}
 
 	if (hw->mac.type == ixgbe_mac_82598EB) {
-- 
GitLab


From 6e455b897bb6be3a4c0c6578f679e83d399e5b92 Mon Sep 17 00:00:00 2001
From: Yi Zou <yi.zou@intel.com>
Date: Thu, 6 Aug 2009 13:05:44 +0000
Subject: [PATCH 0716/1153] ixgbe: Disable packet split only on FCoE queues in
 82599

For 82599, packet split has to be disabled for FCoE direct data placement.
However, this is only required on received queues allocated for FCoE. This
patch adds a per ring flags to indicate if packet split is disabled on a
per queue basis, particularly for FCoE, as packet split must be disabled
for large receive using direct data placement (DDP).

Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ixgbe/ixgbe.h      |  2 ++
 drivers/net/ixgbe/ixgbe_main.c | 33 +++++++++++++++++----------------
 2 files changed, 19 insertions(+), 16 deletions(-)

diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h
index e11d83d5852..2c4dc8221dc 100644
--- a/drivers/net/ixgbe/ixgbe.h
+++ b/drivers/net/ixgbe/ixgbe.h
@@ -136,6 +136,8 @@ struct ixgbe_ring {
 
 	u8 queue_index; /* needed for multiqueue queue management */
 
+#define IXGBE_RING_RX_PS_ENABLED                (u8)(1)
+	u8 flags;			/* per ring feature flags */
 	u16 head;
 	u16 tail;
 
diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index e361b7f0101..e3cb949b9aa 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -585,7 +585,7 @@ static void ixgbe_alloc_rx_buffers(struct ixgbe_adapter *adapter,
 		rx_desc = IXGBE_RX_DESC_ADV(*rx_ring, i);
 
 		if (!bi->page_dma &&
-		    (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED)) {
+		    (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED)) {
 			if (!bi->page) {
 				bi->page = alloc_page(GFP_ATOMIC);
 				if (!bi->page) {
@@ -629,7 +629,7 @@ static void ixgbe_alloc_rx_buffers(struct ixgbe_adapter *adapter,
 		}
 		/* Refresh the desc even if buffer_addrs didn't change because
 		 * each write-back erases this info. */
-		if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) {
+		if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) {
 			rx_desc->read.pkt_addr = cpu_to_le64(bi->page_dma);
 			rx_desc->read.hdr_addr = cpu_to_le64(bi->dma);
 		} else {
@@ -726,7 +726,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector,
 			break;
 		(*work_done)++;
 
-		if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) {
+		if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) {
 			hdr_info = le16_to_cpu(ixgbe_get_hdr_info(rx_desc));
 			len = (hdr_info & IXGBE_RXDADV_HDRBUFLEN_MASK) >>
 			       IXGBE_RXDADV_HDRBUFLEN_SHIFT;
@@ -798,7 +798,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_q_vector *q_vector,
 			rx_ring->stats.packets++;
 			rx_ring->stats.bytes += skb->len;
 		} else {
-			if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) {
+			if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) {
 				rx_buffer_info->skb = next_buffer->skb;
 				rx_buffer_info->dma = next_buffer->dma;
 				next_buffer->skb = skb;
@@ -1919,7 +1919,7 @@ static void ixgbe_configure_srrctl(struct ixgbe_adapter *adapter,
 	srrctl |= (IXGBE_RX_HDR_SIZE << IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT) &
 		  IXGBE_SRRCTL_BSIZEHDR_MASK;
 
-	if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) {
+	if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) {
 #if (PAGE_SIZE / 2) > IXGBE_MAX_RXBUFFER
 		srrctl |= IXGBE_MAX_RXBUFFER >> IXGBE_SRRCTL_BSIZEPKT_SHIFT;
 #else
@@ -1992,11 +1992,6 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 	/* Decide whether to use packet split mode or not */
 	adapter->flags |= IXGBE_FLAG_RX_PS_ENABLED;
 
-#ifdef IXGBE_FCOE
-	if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED)
-		adapter->flags &= ~IXGBE_FLAG_RX_PS_ENABLED;
-#endif /* IXGBE_FCOE */
-
 	/* Set the RX buffer length according to the mode */
 	if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) {
 		rx_buf_len = IXGBE_RX_HDR_SIZE;
@@ -2056,14 +2051,19 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 		rx_ring->tail = IXGBE_RDT(j);
 		rx_ring->rx_buf_len = rx_buf_len;
 
+		if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED)
+			rx_ring->flags |= IXGBE_RING_RX_PS_ENABLED;
+
 #ifdef IXGBE_FCOE
 		if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED) {
 			struct ixgbe_ring_feature *f;
 			f = &adapter->ring_feature[RING_F_FCOE];
-			if ((rx_buf_len < IXGBE_FCOE_JUMBO_FRAME_SIZE) &&
-			    (i >= f->mask) && (i < f->mask + f->indices))
-				rx_ring->rx_buf_len =
-				        IXGBE_FCOE_JUMBO_FRAME_SIZE;
+			if ((i >= f->mask) && (i < f->mask + f->indices)) {
+				rx_ring->flags &= ~IXGBE_RING_RX_PS_ENABLED;
+				if (rx_buf_len < IXGBE_FCOE_JUMBO_FRAME_SIZE)
+					rx_ring->rx_buf_len =
+					        IXGBE_FCOE_JUMBO_FRAME_SIZE;
+			}
 		}
 
 #endif /* IXGBE_FCOE */
@@ -2143,7 +2143,8 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 	if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) {
 		/* Enable 82599 HW-RSC */
 		for (i = 0; i < adapter->num_rx_queues; i++) {
-			j = adapter->rx_ring[i].reg_idx;
+			rx_ring = &adapter->rx_ring[i];
+			j = rx_ring->reg_idx;
 			rscctrl = IXGBE_READ_REG(hw, IXGBE_RSCCTL(j));
 			rscctrl |= IXGBE_RSCCTL_RSCEN;
 			/*
@@ -2151,7 +2152,7 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 			 * total size of max desc * buf_len is not greater
 			 * than 65535
 			 */
-			if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) {
+			if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) {
 #if (MAX_SKB_FRAGS > 16)
 				rscctrl |= IXGBE_RSCCTL_MAXDESC_16;
 #elif (MAX_SKB_FRAGS > 8)
-- 
GitLab


From 373a88d78be540c1331ea5adcb76610dddcb008b Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Fri, 7 Aug 2009 07:41:37 +0000
Subject: [PATCH 0717/1153] e1000e: fix acquisition of SW/FW/HW semaphore for
 ICHx parts

For ICHx parts, write the EXTCNF_CTRL.SWFLAG bit once when trying to
acquire the SW/FW/HW semaphore instead of multiple times to prevent the
hardware from having problems (especially for systems with manageability
enabled), and extend the timeout for the hardware to set the SWFLAG bit.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/e1000e/ich8lan.c | 44 +++++++++++++++++++++++++-----------
 1 file changed, 31 insertions(+), 13 deletions(-)

diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index d56c7473144..dd61e7e98dd 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -594,8 +594,8 @@ static DEFINE_MUTEX(nvm_mutex);
  **/
 static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw)
 {
-	u32 extcnf_ctrl;
-	u32 timeout = PHY_CFG_TIMEOUT;
+	u32 extcnf_ctrl, timeout = PHY_CFG_TIMEOUT;
+	s32 ret_val = 0;
 
 	might_sleep();
 
@@ -603,28 +603,46 @@ static s32 e1000_acquire_swflag_ich8lan(struct e1000_hw *hw)
 
 	while (timeout) {
 		extcnf_ctrl = er32(EXTCNF_CTRL);
+		if (!(extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG))
+			break;
 
-		if (!(extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)) {
-			extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
-			ew32(EXTCNF_CTRL, extcnf_ctrl);
+		mdelay(1);
+		timeout--;
+	}
+
+	if (!timeout) {
+		hw_dbg(hw, "SW/FW/HW has locked the resource for too long.\n");
+		ret_val = -E1000_ERR_CONFIG;
+		goto out;
+	}
+
+	timeout = PHY_CFG_TIMEOUT * 2;
+
+	extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
+	ew32(EXTCNF_CTRL, extcnf_ctrl);
+
+	while (timeout) {
+		extcnf_ctrl = er32(EXTCNF_CTRL);
+		if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
+			break;
 
-			extcnf_ctrl = er32(EXTCNF_CTRL);
-			if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
-				break;
-		}
 		mdelay(1);
 		timeout--;
 	}
 
 	if (!timeout) {
-		hw_dbg(hw, "FW or HW has locked the resource for too long.\n");
+		hw_dbg(hw, "Failed to acquire the semaphore.\n");
 		extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
 		ew32(EXTCNF_CTRL, extcnf_ctrl);
-		mutex_unlock(&nvm_mutex);
-		return -E1000_ERR_CONFIG;
+		ret_val = -E1000_ERR_CONFIG;
+		goto out;
 	}
 
-	return 0;
+out:
+	if (ret_val)
+		mutex_unlock(&nvm_mutex);
+
+	return ret_val;
 }
 
 /**
-- 
GitLab


From 148675a7b2061b5a5eb194530b7c4d8de1f2887e Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Fri, 7 Aug 2009 07:41:56 +0000
Subject: [PATCH 0718/1153] e1000e: fix potential NVM corruption on ICH9 with
 8K bank size

The bank offset was being incorrectly calculated on ICH9 parts with a bank
size of 8K (instead of the more common 4K bank) which would cause any NVM
writes to be done on the wrong address after switching from bank 1 to bank
0.  Additionally, assume we are meant to use bank 0 if a valid bank is not
detected, and remove the unnecessary acquisition of the SW/FW/HW semaphore
when writing to the shadow ram version of the NVM image.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/e1000e/ich8lan.c | 50 +++++++++---------------------------
 1 file changed, 12 insertions(+), 38 deletions(-)

diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index dd61e7e98dd..99df2abf82a 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -338,10 +338,7 @@ static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw)
 {
 	struct e1000_nvm_info *nvm = &hw->nvm;
 	struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
-	union ich8_hws_flash_status hsfsts;
-	u32 gfpreg;
-	u32 sector_base_addr;
-	u32 sector_end_addr;
+	u32 gfpreg, sector_base_addr, sector_end_addr;
 	u16 i;
 
 	/* Can't read flash registers if the register set isn't mapped. */
@@ -375,20 +372,6 @@ static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw)
 	/* Adjust to word count */
 	nvm->flash_bank_size /= sizeof(u16);
 
-	/*
-	 * Make sure the flash bank size does not overwrite the 4k
-	 * sector ranges. We may have 64k allotted to us but we only care
-	 * about the first 2 4k sectors. Therefore, if we have anything less
-	 * than 64k set in the HSFSTS register, we will reduce the bank size
-	 * down to 4k and let the rest remain unused. If berasesz == 3, then
-	 * we are working in 64k mode. Otherwise we are not.
-	 */
-	if (nvm->flash_bank_size > E1000_ICH8_SHADOW_RAM_WORDS) {
-		hsfsts.regval = er16flash(ICH_FLASH_HSFSTS);
-		if (hsfsts.hsf_status.berasesz != 3)
-			nvm->flash_bank_size = E1000_ICH8_SHADOW_RAM_WORDS;
-	}
-
 	nvm->word_size = E1000_ICH8_SHADOW_RAM_WORDS;
 
 	/* Clear shadow ram */
@@ -1324,7 +1307,7 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
 	struct e1000_nvm_info *nvm = &hw->nvm;
 	struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
 	u32 act_offset;
-	s32 ret_val;
+	s32 ret_val = 0;
 	u32 bank = 0;
 	u16 i, word;
 
@@ -1339,12 +1322,15 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
 		goto out;
 
 	ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
-	if (ret_val)
-		goto release;
+	if (ret_val) {
+		hw_dbg(hw, "Could not detect valid bank, assuming bank 0\n");
+		bank = 0;
+	}
 
 	act_offset = (bank) ? nvm->flash_bank_size : 0;
 	act_offset += offset;
 
+	ret_val = 0;
 	for (i = 0; i < words; i++) {
 		if ((dev_spec->shadow_ram) &&
 		    (dev_spec->shadow_ram[offset+i].modified)) {
@@ -1359,7 +1345,6 @@ static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
 		}
 	}
 
-release:
 	e1000_release_swflag_ich8lan(hw);
 
 out:
@@ -1610,7 +1595,6 @@ static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
 {
 	struct e1000_nvm_info *nvm = &hw->nvm;
 	struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
-	s32 ret_val;
 	u16 i;
 
 	if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) ||
@@ -1619,17 +1603,11 @@ static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
 		return -E1000_ERR_NVM;
 	}
 
-	ret_val = e1000_acquire_swflag_ich8lan(hw);
-	if (ret_val)
-		return ret_val;
-
 	for (i = 0; i < words; i++) {
 		dev_spec->shadow_ram[offset+i].modified = 1;
 		dev_spec->shadow_ram[offset+i].value = data[i];
 	}
 
-	e1000_release_swflag_ich8lan(hw);
-
 	return 0;
 }
 
@@ -1670,8 +1648,8 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
 	 */
 	ret_val =  e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
 	if (ret_val) {
-		e1000_release_swflag_ich8lan(hw);
-		goto out;
+		hw_dbg(hw, "Could not detect valid bank, assuming bank 0\n");
+		bank = 0;
 	}
 
 	if (bank == 0) {
@@ -2057,12 +2035,8 @@ static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank)
 		iteration = 1;
 		break;
 	case 2:
-		if (hw->mac.type == e1000_ich9lan) {
-			sector_size = ICH_FLASH_SEG_SIZE_8K;
-			iteration = flash_bank_size / ICH_FLASH_SEG_SIZE_8K;
-		} else {
-			return -E1000_ERR_NVM;
-		}
+		sector_size = ICH_FLASH_SEG_SIZE_8K;
+		iteration = 1;
 		break;
 	case 3:
 		sector_size = ICH_FLASH_SEG_SIZE_64K;
@@ -2074,7 +2048,7 @@ static s32 e1000_erase_flash_bank_ich8lan(struct e1000_hw *hw, u32 bank)
 
 	/* Start with the base address, then add the sector offset. */
 	flash_linear_addr = hw->nvm.flash_base_addr;
-	flash_linear_addr += (bank) ? (sector_size * iteration) : 0;
+	flash_linear_addr += (bank) ? flash_bank_size : 0;
 
 	for (j = 0; j < iteration ; j++) {
 		do {
-- 
GitLab


From 75c4885924f01aed1f887886a49dfa89960de240 Mon Sep 17 00:00:00 2001
From: Yong Zhang <yong.zhang0@gmail.com>
Date: Fri, 7 Aug 2009 16:36:52 +0000
Subject: [PATCH 0719/1153] gianfar: keep vlan related state when restart

If vlan has been enabled. ifdown followed by ifup will lost hardware
related state.

Also remove duplicated operation in gfar_vlan_rx_register().

Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/gianfar.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c
index f8ffcbf0bc3..e212f2c5448 100644
--- a/drivers/net/gianfar.c
+++ b/drivers/net/gianfar.c
@@ -936,6 +936,7 @@ int startup_gfar(struct net_device *dev)
 	struct gfar __iomem *regs = priv->regs;
 	int err = 0;
 	u32 rctrl = 0;
+	u32 tctrl = 0;
 	u32 attrs = 0;
 
 	gfar_write(&regs->imask, IMASK_INIT_CLEAR);
@@ -1111,11 +1112,19 @@ int startup_gfar(struct net_device *dev)
 		rctrl |= RCTRL_PADDING(priv->padding);
 	}
 
+	/* keep vlan related bits if it's enabled */
+	if (priv->vlgrp) {
+		rctrl |= RCTRL_VLEX | RCTRL_PRSDEP_INIT;
+		tctrl |= TCTRL_VLINS;
+	}
+
 	/* Init rctrl based on our settings */
 	gfar_write(&priv->regs->rctrl, rctrl);
 
 	if (dev->features & NETIF_F_IP_CSUM)
-		gfar_write(&priv->regs->tctrl, TCTRL_INIT_CSUM);
+		tctrl |= TCTRL_INIT_CSUM;
+
+	gfar_write(&priv->regs->tctrl, tctrl);
 
 	/* Set the extraction length and index */
 	attrs = ATTRELI_EL(priv->rx_stash_size) |
@@ -1450,7 +1459,6 @@ static void gfar_vlan_rx_register(struct net_device *dev,
 
 		/* Enable VLAN tag extraction */
 		tempval = gfar_read(&priv->regs->rctrl);
-		tempval |= RCTRL_VLEX;
 		tempval |= (RCTRL_VLEX | RCTRL_PRSDEP_INIT);
 		gfar_write(&priv->regs->rctrl, tempval);
 	} else {
-- 
GitLab


From 018d21ed80736eab21fabf45edbd74600a1f8330 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Fri, 7 Aug 2009 06:43:01 +0000
Subject: [PATCH 0720/1153] MAINTAINERS: additional NETWORKING [GENERAL] and
 NETWORKING DRIVERS patterns

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 MAINTAINERS | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index fa76ad0a37e..aee67a88889 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3555,6 +3555,9 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git
 S:	Maintained
 F:	net/
 F:	include/net/
+F:	include/linux/in.h
+F:	include/linux/net.h
+F:	include/linux/netdevice.h
 
 NETWORKING [IPv4/IPv6]
 M:	"David S. Miller" <davem@davemloft.net>
@@ -3590,6 +3593,8 @@ W:	http://www.linuxfoundation.org/en/Net
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git
 S:	Odd Fixes
 F:	drivers/net/
+F:	include/linux/if_*
+F:	include/linux/*device.h
 
 NETXEN (1/10) GbE SUPPORT
 M:	Dhananjay Phadke <dhananjay@netxen.com>
-- 
GitLab


From 418372b0ab7a3bbcc59d71e8e4d322ef18263dab Mon Sep 17 00:00:00 2001
From: Rafael Laufer <rlaufer@cisco.com>
Date: Fri, 7 Aug 2009 05:17:17 +0000
Subject: [PATCH 0721/1153] sctp: fix missing destroy of percpu counter
 variable in sctp_proc_exit()

Commit 1748376b6626acf59c24e9592ac67b3fe2a0e026,
	net: Use a percpu_counter for sockets_allocated

added percpu_counter function calls to sctp_proc_init code path, but
forgot to add them to sctp_proc_exit().  This resulted in a following
Ooops when performing this test
	# modprobe sctp
	# rmmod -f sctp
	# modprobe sctp

[  573.862512] BUG: unable to handle kernel paging request at f8214a24
[  573.862518] IP: [<c0308b8f>] __percpu_counter_init+0x3f/0x70
[  573.862530] *pde = 37010067 *pte = 00000000
[  573.862534] Oops: 0002 [#1] SMP
[  573.862537] last sysfs file: /sys/module/libcrc32c/initstate
[  573.862540] Modules linked in: sctp(+) crc32c libcrc32c binfmt_misc bridge
stp bnep lp snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_hwdep
snd_pcm_oss snd_mixer_oss arc4 joydev snd_pcm ecb pcmcia snd_seq_dummy
snd_seq_oss iwlagn iwlcore snd_seq_midi snd_rawmidi snd_seq_midi_event
yenta_socket rsrc_nonstatic thinkpad_acpi snd_seq snd_timer snd_seq_device
mac80211 psmouse sdhci_pci sdhci nvidia(P) ppdev video snd soundcore serio_raw
pcspkr iTCO_wdt iTCO_vendor_support led_class ricoh_mmc pcmcia_core intel_agp
nvram agpgart usbhid parport_pc parport output snd_page_alloc cfg80211 btusb
ohci1394 ieee1394 e1000e [last unloaded: sctp]
[  573.862589]
[  573.862593] Pid: 5373, comm: modprobe Tainted: P  R        (2.6.31-rc3 #6)
7663B15
[  573.862596] EIP: 0060:[<c0308b8f>] EFLAGS: 00010286 CPU: 1
[  573.862599] EIP is at __percpu_counter_init+0x3f/0x70
[  573.862602] EAX: f8214a20 EBX: f80faa14 ECX: c48c0000 EDX: f80faa20
[  573.862604] ESI: f80a7000 EDI: 00000000 EBP: f69d5ef0 ESP: f69d5eec
[  573.862606]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  573.862610] Process modprobe (pid: 5373, ti=f69d4000 task=c2130c70
task.ti=f69d4000)
[  573.862612] Stack:
[  573.862613]  00000000 f69d5f18 f80a70a8 f80fa9fc 00000000 fffffffc f69d5f30
c018e2d4
[  573.862619] <0> 00000000 f80a7000 00000000 f69d5f88 c010112b 00000000
c07029c0 fffffffb
[  573.862626] <0> 00000000 f69d5f38 c018f83f f69d5f54 c0557cad f80fa860
00000001 c07010c0
[  573.862634] Call Trace:
[  573.862644]  [<f80a70a8>] ? sctp_init+0xa8/0x7d4 [sctp]
[  573.862650]  [<c018e2d4>] ? marker_update_probe_range+0x184/0x260
[  573.862659]  [<f80a7000>] ? sctp_init+0x0/0x7d4 [sctp]
[  573.862662]  [<c010112b>] ? do_one_initcall+0x2b/0x160
[  573.862666]  [<c018f83f>] ? tracepoint_module_notify+0x2f/0x40
[  573.862671]  [<c0557cad>] ? notifier_call_chain+0x2d/0x70
[  573.862678]  [<c01588fd>] ? __blocking_notifier_call_chain+0x4d/0x60
[  573.862682]  [<c016b2f1>] ? sys_init_module+0xb1/0x1f0
[  573.862686]  [<c0102ffc>] ? sysenter_do_call+0x12/0x28
[  573.862688] Code: 89 48 08 b8 04 00 00 00 e8 df aa ec ff ba f4 ff ff ff 85
c0 89 43 14 74 31 b8 b0 18 71 c0 e8 19 b9 24 00 a1 c4 18 71 c0 8d 53 0c <89> 50
04 89 43 0c b8 b0 18 71 c0 c7 43 10 c4 18 71 c0 89 15 c4
[  573.862725] EIP: [<c0308b8f>] __percpu_counter_init+0x3f/0x70 SS:ESP
0068:f69d5eec
[  573.862730] CR2: 00000000f8214a24
[  573.862734] ---[ end trace 39c4e0b55e7cf54d ]---

Signed-off-by: Rafael Laufer <rlaufer@cisco.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/sctp/protocol.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/sctp/protocol.c b/net/sctp/protocol.c
index 79cbd47f4df..a76da657244 100644
--- a/net/sctp/protocol.c
+++ b/net/sctp/protocol.c
@@ -160,6 +160,7 @@ static void sctp_proc_exit(void)
 		remove_proc_entry("sctp", init_net.proc_net);
 	}
 #endif
+	percpu_counter_destroy(&sctp_sockets_allocated);
 }
 
 /* Private helper to extract ipv4 address and stash them in
-- 
GitLab


From 5e33b719c8fcccfedc1d25167826a0f93fe6c5a1 Mon Sep 17 00:00:00 2001
From: roel kluin <roel.kluin@gmail.com>
Date: Fri, 7 Aug 2009 03:24:27 +0000
Subject: [PATCH 0722/1153] pcnet32: Read buffer overflow

An `options[cards_found]' that equals `sizeof(options_mapping)' is already beyond
the array.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/pcnet32.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/pcnet32.c b/drivers/net/pcnet32.c
index a646a445fda..23e1a0750fe 100644
--- a/drivers/net/pcnet32.c
+++ b/drivers/net/pcnet32.c
@@ -1839,7 +1839,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev)
 	lp->chip_version = chip_version;
 	lp->msg_enable = pcnet32_debug;
 	if ((cards_found >= MAX_UNITS)
-	    || (options[cards_found] > sizeof(options_mapping)))
+	    || (options[cards_found] >= sizeof(options_mapping)))
 		lp->options = PCNET32_PORT_ASEL;
 	else
 		lp->options = options_mapping[options[cards_found]];
-- 
GitLab


From be12159b24c532b4b48bdec5a543336438faa132 Mon Sep 17 00:00:00 2001
From: roel kluin <roel.kluin@gmail.com>
Date: Sun, 9 Aug 2009 04:00:25 +0000
Subject: [PATCH 0723/1153] zorro8390: Fix read buffer overflow in
 zorro8390_init_one()

Prevent read from cards[-1] when no card was found.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/zorro8390.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/zorro8390.c b/drivers/net/zorro8390.c
index 37c84e3b8be..81c753a617a 100644
--- a/drivers/net/zorro8390.c
+++ b/drivers/net/zorro8390.c
@@ -120,6 +120,9 @@ static int __devinit zorro8390_init_one(struct zorro_dev *z,
     for (i = ARRAY_SIZE(cards)-1; i >= 0; i--)
 	if (z->id == cards[i].id)
 	    break;
+    if (i < 0)
+        return -ENODEV;
+
     board = z->resource.start;
     ioaddr = board+cards[i].offset;
     dev = alloc_ei_netdev();
-- 
GitLab


From 973507cb8610d4c84f090d5f1f0ca54fa0559d27 Mon Sep 17 00:00:00 2001
From: roel kluin <roel.kluin@gmail.com>
Date: Sat, 8 Aug 2009 23:54:21 +0000
Subject: [PATCH 0724/1153] mlx4_en: Fix read buffer overflow in
 mlx4_en_complete_rx_desc()

If the length is less or equal to frag_prefix_size in the first iteration
we write skb_frags_rx[-1] and read from priv->frag_info[-1]

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/mlx4/en_rx.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/net/mlx4/en_rx.c b/drivers/net/mlx4/en_rx.c
index 91bdfdfd431..3ac0404d0d1 100644
--- a/drivers/net/mlx4/en_rx.c
+++ b/drivers/net/mlx4/en_rx.c
@@ -506,8 +506,9 @@ static int mlx4_en_complete_rx_desc(struct mlx4_en_priv *priv,
 				 PCI_DMA_FROMDEVICE);
 	}
 	/* Adjust size of last fragment to match actual length */
-	skb_frags_rx[nr - 1].size = length -
-		priv->frag_info[nr - 1].frag_prefix_size;
+	if (nr > 0)
+		skb_frags_rx[nr - 1].size = length -
+			priv->frag_info[nr - 1].frag_prefix_size;
 	return nr;
 
 fail:
-- 
GitLab


From b2f2e8fee3d62f621e795f25b2fc0f51bbdb4af9 Mon Sep 17 00:00:00 2001
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Mon, 10 Aug 2009 16:36:38 +1000
Subject: [PATCH 0725/1153] powerpc/dma: pci_set_dma_mask() shouldn't fail if
 mask fits in RAM

On an iMac G5, the b43 driver is failing to initialise because trying to
set the dma mask to 30-bit fails. Even though there's only 512MiB of RAM
in the machine anyway:
	https://bugzilla.redhat.com/show_bug.cgi?id=514787

We should probably let it succeed if the available RAM in the system
doesn't exceed the requested limit.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/kernel/dma.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/powerpc/kernel/dma.c b/arch/powerpc/kernel/dma.c
index 20a60d661ba..ccf129d47d8 100644
--- a/arch/powerpc/kernel/dma.c
+++ b/arch/powerpc/kernel/dma.c
@@ -7,6 +7,7 @@
 
 #include <linux/device.h>
 #include <linux/dma-mapping.h>
+#include <linux/lmb.h>
 #include <asm/bug.h>
 #include <asm/abs_addr.h>
 
@@ -90,11 +91,10 @@ static void dma_direct_unmap_sg(struct device *dev, struct scatterlist *sg,
 static int dma_direct_dma_supported(struct device *dev, u64 mask)
 {
 #ifdef CONFIG_PPC64
-	/* Could be improved to check for memory though it better be
-	 * done via some global so platforms can set the limit in case
+	/* Could be improved so platforms can set the limit in case
 	 * they have limited DMA windows
 	 */
-	return mask >= DMA_BIT_MASK(32);
+	return mask >= (lmb_end_of_DRAM() - 1);
 #else
 	return 1;
 #endif
-- 
GitLab


From beda2c7ea2c15ed01eef00a997d2b0496c3a502d Mon Sep 17 00:00:00 2001
From: Darren Hart <dvhltc@us.ibm.com>
Date: Sun, 9 Aug 2009 15:34:39 -0700
Subject: [PATCH 0726/1153] futex: Update futex_q lock_ptr on requeue proxy
 lock

futex_requeue() can acquire the lock on behalf of a waiter
early on or during the requeue loop if it is uncontended or in
the event of a lock steal or owner died. On wakeup, the waiter
(in futex_wait_requeue_pi()) cleans up the pi_state owner using
the lock_ptr to protect against concurrent access to the
pi_state. The pi_state is hung off futex_q's on the requeue
target futex hash bucket so the lock_ptr needs to be updated
accordingly.

The problem manifested by triggering the WARN_ON in
lookup_pi_state() about the pid != pi_state->owner->pid.  With
this patch, the pi_state is properly guarded against concurrent
access via the requeue target hb lock.

The astute reviewer may notice that there is a window of time
between when futex_requeue() unlocks the hb locks and when
futex_wait_requeue_pi() will acquire hb2->lock.  During this
time the pi_state and uval are not in sync with the underlying
rtmutex owner (but the uval does indicate there are waiters, so
no atomic changes will occur in userspace).  However, this is
not a problem. Should a contending thread enter
lookup_pi_state() and acquire hb2->lock before the ownership is
fixed up, it will find the pi_state hung off a waiter's
(possibly the pending owner's) futex_q and block on the
rtmutex.  Once futex_wait_requeue_pi() fixes up the owner, it
will also move the pi_state from the old owner's
task->pi_state_list to its own.

v3: Fix plist lock name for application to mainline (rather
    than -rt) Compile tested against tip/v2.6.31-rc5.

Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dinakar Guniguntala <dino@in.ibm.com>
Cc: John Stultz <johnstul@linux.vnet.ibm.com>
LKML-Reference: <4A7F4EFF.6090903@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/futex.c | 17 +++++++++++++----
 1 file changed, 13 insertions(+), 4 deletions(-)

diff --git a/kernel/futex.c b/kernel/futex.c
index 0672ff88f15..8cc3ee1363a 100644
--- a/kernel/futex.c
+++ b/kernel/futex.c
@@ -1010,15 +1010,19 @@ void requeue_futex(struct futex_q *q, struct futex_hash_bucket *hb1,
  * requeue_pi_wake_futex() - Wake a task that acquired the lock during requeue
  * q:	the futex_q
  * key:	the key of the requeue target futex
+ * hb:  the hash_bucket of the requeue target futex
  *
  * During futex_requeue, with requeue_pi=1, it is possible to acquire the
  * target futex if it is uncontended or via a lock steal.  Set the futex_q key
  * to the requeue target futex so the waiter can detect the wakeup on the right
  * futex, but remove it from the hb and NULL the rt_waiter so it can detect
- * atomic lock acquisition.  Must be called with the q->lock_ptr held.
+ * atomic lock acquisition.  Set the q->lock_ptr to the requeue target hb->lock
+ * to protect access to the pi_state to fixup the owner later.  Must be called
+ * with both q->lock_ptr and hb->lock held.
  */
 static inline
-void requeue_pi_wake_futex(struct futex_q *q, union futex_key *key)
+void requeue_pi_wake_futex(struct futex_q *q, union futex_key *key,
+			   struct futex_hash_bucket *hb)
 {
 	drop_futex_key_refs(&q->key);
 	get_futex_key_refs(key);
@@ -1030,6 +1034,11 @@ void requeue_pi_wake_futex(struct futex_q *q, union futex_key *key)
 	WARN_ON(!q->rt_waiter);
 	q->rt_waiter = NULL;
 
+	q->lock_ptr = &hb->lock;
+#ifdef CONFIG_DEBUG_PI_LIST
+	q->list.plist.lock = &hb->lock;
+#endif
+
 	wake_up_state(q->task, TASK_NORMAL);
 }
 
@@ -1088,7 +1097,7 @@ static int futex_proxy_trylock_atomic(u32 __user *pifutex,
 	ret = futex_lock_pi_atomic(pifutex, hb2, key2, ps, top_waiter->task,
 				   set_waiters);
 	if (ret == 1)
-		requeue_pi_wake_futex(top_waiter, key2);
+		requeue_pi_wake_futex(top_waiter, key2, hb2);
 
 	return ret;
 }
@@ -1273,7 +1282,7 @@ retry_private:
 							this->task, 1);
 			if (ret == 1) {
 				/* We got the lock. */
-				requeue_pi_wake_futex(this, &key2);
+				requeue_pi_wake_futex(this, &key2, hb2);
 				continue;
 			} else if (ret) {
 				/* -EDEADLK */
-- 
GitLab


From a044560c3a1f0ad75ce685c1ed7604820b9ed319 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Mon, 10 Aug 2009 11:16:52 +0200
Subject: [PATCH 0727/1153] perf_counter: Correct PERF_SAMPLE_RAW output

PERF_SAMPLE_* output switches should unconditionally output the
correct format, as they are the only way to unambiguously parse
the PERF_EVENT_SAMPLE data.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1249896447.17467.74.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 include/linux/perf_counter.h |  2 ++
 include/trace/ftrace.h       |  3 ++-
 kernel/perf_counter.c        | 30 ++++++++++++++++++++++++------
 3 files changed, 28 insertions(+), 7 deletions(-)

diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h
index 2aabe43c1d0..a9d823a93fe 100644
--- a/include/linux/perf_counter.h
+++ b/include/linux/perf_counter.h
@@ -369,6 +369,8 @@ enum perf_event_type {
 	 *
 	 *	{ u64			nr,
 	 *	  u64			ips[nr];  } && PERF_SAMPLE_CALLCHAIN
+	 *	{ u32			size;
+	 *	  char                  data[size];}&& PERF_SAMPLE_RAW
 	 * };
 	 */
 	PERF_EVENT_SAMPLE		= 9,
diff --git a/include/trace/ftrace.h b/include/trace/ftrace.h
index 7fb16d90e7b..7167b9b97da 100644
--- a/include/trace/ftrace.h
+++ b/include/trace/ftrace.h
@@ -685,7 +685,8 @@ static void ftrace_profile_##call(proto)				\
 	pc = preempt_count();						\
 									\
 	__data_size = ftrace_get_offsets_##call(&__data_offsets, args); \
-	__entry_size = ALIGN(__data_size + sizeof(*entry), sizeof(u64));\
+	__entry_size = ALIGN(__data_size + sizeof(*entry) + sizeof(u32),\
+			     sizeof(u64));				\
 									\
 	do {								\
 		char raw_data[__entry_size];				\
diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 546e62d6294..5229d1666fa 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -2646,7 +2646,6 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 		u64 counter;
 	} group_entry;
 	struct perf_callchain_entry *callchain = NULL;
-	struct perf_raw_record *raw = NULL;
 	int callchain_size = 0;
 	u64 time;
 	struct {
@@ -2716,9 +2715,15 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 	}
 
 	if (sample_type & PERF_SAMPLE_RAW) {
-		raw = data->raw;
-		if (raw)
-			header.size += raw->size;
+		int size = sizeof(u32);
+
+		if (data->raw)
+			size += data->raw->size;
+		else
+			size += sizeof(u32);
+
+		WARN_ON_ONCE(size & (sizeof(u64)-1));
+		header.size += size;
 	}
 
 	ret = perf_output_begin(&handle, counter, header.size, nmi, 1);
@@ -2784,8 +2789,21 @@ static void perf_counter_output(struct perf_counter *counter, int nmi,
 		}
 	}
 
-	if ((sample_type & PERF_SAMPLE_RAW) && raw)
-		perf_output_copy(&handle, raw->data, raw->size);
+	if (sample_type & PERF_SAMPLE_RAW) {
+		if (data->raw) {
+			perf_output_put(&handle, data->raw->size);
+			perf_output_copy(&handle, data->raw->data, data->raw->size);
+		} else {
+			struct {
+				u32	size;
+				u32	data;
+			} raw = {
+				.size = sizeof(u32),
+				.data = 0,
+			};
+			perf_output_put(&handle, raw);
+		}
+	}
 
 	perf_output_end(&handle);
 }
-- 
GitLab


From a4e95fc2cbb31d70a65beffeaf8773f881328c34 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Mon, 10 Aug 2009 11:20:12 +0200
Subject: [PATCH 0728/1153] perf_counter: Require CAP_SYS_ADMIN for raw
 tracepoint data

Raw tracepoint data contains various kernel internals and
data from other users, so restrict this to CAP_SYS_ADMIN.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1249896452.17467.75.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 5229d1666fa..b0b20a07f39 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -3787,6 +3787,14 @@ static void tp_perf_counter_destroy(struct perf_counter *counter)
 
 static const struct pmu *tp_perf_counter_init(struct perf_counter *counter)
 {
+	/*
+	 * Raw tracepoint data is a severe data leak, only allow root to
+	 * have these.
+	 */
+	if ((counter->attr.sample_type & PERF_SAMPLE_RAW) &&
+			!capable(CAP_SYS_ADMIN))
+		return ERR_PTR(-EPERM);
+
 	if (ftrace_profile_enable(counter->attr.config))
 		return NULL;
 
-- 
GitLab


From 100d5eb36ba20dc0b99a17ea2b9800c567bfc3d1 Mon Sep 17 00:00:00 2001
From: Takashi Iwai <tiwai@suse.de>
Date: Mon, 10 Aug 2009 11:55:51 +0200
Subject: [PATCH 0729/1153] ALSA: hda - Add missing vmaster initialization for
 ALC269

Without the initialization of vmaster NID, the dB information got
confused for ALC269 codec.

Reference: Novell bnc#527361
	https://bugzilla.novell.com/show_bug.cgi?id=527361

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
---
 sound/pci/hda/patch_realtek.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index 51c44fdbc0f..5cc927f4783 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -13563,6 +13563,8 @@ static int patch_alc269(struct hda_codec *codec)
 		set_capture_mixer(spec);
 	set_beep_amp(spec, 0x0b, 0x04, HDA_INPUT);
 
+	spec->vmaster_nid = 0x02;
+
 	codec->patch_ops = alc_patch_ops;
 	if (board_config == ALC269_AUTO)
 		spec->init_hook = alc269_auto_init;
-- 
GitLab


From 13f0feafa6b8aead57a2a328e2fca6a5828bf286 Mon Sep 17 00:00:00 2001
From: Oleg Nesterov <oleg@redhat.com>
Date: Tue, 23 Jun 2009 21:25:32 +0200
Subject: [PATCH 0730/1153] mm_for_maps: simplify, use ptrace_may_access()

It would be nice to kill __ptrace_may_access(). It requires task_lock(),
but this lock is only needed to read mm->flags in the middle.

Convert mm_for_maps() to use ptrace_may_access(), this also simplifies
the code a little bit.

Also, we do not need to take ->mmap_sem in advance. In fact I think
mm_for_maps() should not play with ->mmap_sem at all, the caller should
take this lock.

With or without this patch, without ->cred_guard_mutex held we can race
with exec() and get the new ->mm but check old creds.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 fs/proc/base.c | 23 +++++++++++------------
 1 file changed, 11 insertions(+), 12 deletions(-)

diff --git a/fs/proc/base.c b/fs/proc/base.c
index 3ce5ae9e3d2..917f338a673 100644
--- a/fs/proc/base.c
+++ b/fs/proc/base.c
@@ -237,20 +237,19 @@ struct mm_struct *mm_for_maps(struct task_struct *task)
 	struct mm_struct *mm = get_task_mm(task);
 	if (!mm)
 		return NULL;
+	if (mm != current->mm) {
+		/*
+		 * task->mm can be changed before security check,
+		 * in that case we must notice the change after.
+		 */
+		if (!ptrace_may_access(task, PTRACE_MODE_READ) ||
+		    mm != task->mm) {
+			mmput(mm);
+			return NULL;
+		}
+	}
 	down_read(&mm->mmap_sem);
-	task_lock(task);
-	if (task->mm != mm)
-		goto out;
-	if (task->mm != current->mm &&
-	    __ptrace_may_access(task, PTRACE_MODE_READ) < 0)
-		goto out;
-	task_unlock(task);
 	return mm;
-out:
-	task_unlock(task);
-	up_read(&mm->mmap_sem);
-	mmput(mm);
-	return NULL;
 }
 
 static int proc_pid_cmdline(struct task_struct *task, char * buffer)
-- 
GitLab


From 00f89d218523b9bf6b522349c039d5ac80aa536d Mon Sep 17 00:00:00 2001
From: Oleg Nesterov <oleg@redhat.com>
Date: Fri, 10 Jul 2009 03:27:38 +0200
Subject: [PATCH 0731/1153] mm_for_maps: shift down_read(mmap_sem) to the
 caller

mm_for_maps() takes ->mmap_sem after security checks, this looks
strange and obfuscates the locking rules. Move this lock to its
single caller, m_start().

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 fs/proc/base.c       | 8 +++-----
 fs/proc/task_mmu.c   | 1 +
 fs/proc/task_nommu.c | 1 +
 3 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/fs/proc/base.c b/fs/proc/base.c
index 917f338a673..f3c2e4085fe 100644
--- a/fs/proc/base.c
+++ b/fs/proc/base.c
@@ -235,9 +235,8 @@ static int check_mem_permission(struct task_struct *task)
 struct mm_struct *mm_for_maps(struct task_struct *task)
 {
 	struct mm_struct *mm = get_task_mm(task);
-	if (!mm)
-		return NULL;
-	if (mm != current->mm) {
+
+	if (mm && mm != current->mm) {
 		/*
 		 * task->mm can be changed before security check,
 		 * in that case we must notice the change after.
@@ -245,10 +244,9 @@ struct mm_struct *mm_for_maps(struct task_struct *task)
 		if (!ptrace_may_access(task, PTRACE_MODE_READ) ||
 		    mm != task->mm) {
 			mmput(mm);
-			return NULL;
+			mm = NULL;
 		}
 	}
-	down_read(&mm->mmap_sem);
 	return mm;
 }
 
diff --git a/fs/proc/task_mmu.c b/fs/proc/task_mmu.c
index 6f61b7cc32e..9bd8be1d235 100644
--- a/fs/proc/task_mmu.c
+++ b/fs/proc/task_mmu.c
@@ -119,6 +119,7 @@ static void *m_start(struct seq_file *m, loff_t *pos)
 	mm = mm_for_maps(priv->task);
 	if (!mm)
 		return NULL;
+	down_read(&mm->mmap_sem);
 
 	tail_vma = get_gate_vma(priv->task);
 	priv->tail_vma = tail_vma;
diff --git a/fs/proc/task_nommu.c b/fs/proc/task_nommu.c
index 64a72e2e765..8f5c05d3dbd 100644
--- a/fs/proc/task_nommu.c
+++ b/fs/proc/task_nommu.c
@@ -189,6 +189,7 @@ static void *m_start(struct seq_file *m, loff_t *pos)
 		priv->task = NULL;
 		return NULL;
 	}
+	down_read(&mm->mmap_sem);
 
 	/* start from the Nth VMA */
 	for (p = rb_first(&mm->mm_rb); p; p = rb_next(p))
-- 
GitLab


From 704b836cbf19e885f8366bccb2e4b0474346c02d Mon Sep 17 00:00:00 2001
From: Oleg Nesterov <oleg@redhat.com>
Date: Fri, 10 Jul 2009 03:27:40 +0200
Subject: [PATCH 0732/1153] mm_for_maps: take ->cred_guard_mutex to fix the
 race with exec

The problem is minor, but without ->cred_guard_mutex held we can race
with exec() and get the new ->mm but check old creds.

Now we do not need to re-check task->mm after ptrace_may_access(), it
can't be changed to the new mm under us.

Strictly speaking, this also fixes another very minor problem. Unless
security check fails or the task exits mm_for_maps() should never
return NULL, the caller should get either old or new ->mm.

Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 fs/proc/base.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/fs/proc/base.c b/fs/proc/base.c
index f3c2e4085fe..175db258942 100644
--- a/fs/proc/base.c
+++ b/fs/proc/base.c
@@ -234,19 +234,19 @@ static int check_mem_permission(struct task_struct *task)
 
 struct mm_struct *mm_for_maps(struct task_struct *task)
 {
-	struct mm_struct *mm = get_task_mm(task);
+	struct mm_struct *mm;
 
-	if (mm && mm != current->mm) {
-		/*
-		 * task->mm can be changed before security check,
-		 * in that case we must notice the change after.
-		 */
-		if (!ptrace_may_access(task, PTRACE_MODE_READ) ||
-		    mm != task->mm) {
-			mmput(mm);
-			mm = NULL;
-		}
+	if (mutex_lock_killable(&task->cred_guard_mutex))
+		return NULL;
+
+	mm = get_task_mm(task);
+	if (mm && mm != current->mm &&
+			!ptrace_may_access(task, PTRACE_MODE_READ)) {
+		mmput(mm);
+		mm = NULL;
 	}
+	mutex_unlock(&task->cred_guard_mutex);
+
 	return mm;
 }
 
-- 
GitLab


From cd92204924fafbd5c7241dfd12ca3176d542e0c5 Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Mon, 10 Aug 2009 14:49:50 +0300
Subject: [PATCH 0733/1153] OMAP: Fix testing of cpu defines for mach-omap1

There's no need to keep these defines limited in the ifdef block
for mach-omap2. It will just cause problems testing for the CPU
revision in the common code, like the next patch does for the DMA
errata.

Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/plat-omap/include/mach/cpu.h | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/arch/arm/plat-omap/include/mach/cpu.h b/arch/arm/plat-omap/include/mach/cpu.h
index 285eaa3a827..11e73d9e892 100644
--- a/arch/arm/plat-omap/include/mach/cpu.h
+++ b/arch/arm/plat-omap/include/mach/cpu.h
@@ -378,9 +378,6 @@ IS_OMAP_TYPE(3430, 0x3430)
 #define cpu_class_is_omap2()	(cpu_is_omap24xx() || cpu_is_omap34xx() || \
 				cpu_is_omap44xx())
 
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \
-			defined(CONFIG_ARCH_OMAP4)
-
 /* Various silicon revisions for omap2 */
 #define OMAP242X_CLASS		0x24200024
 #define OMAP2420_REV_ES1_0	0x24200024
@@ -436,5 +433,3 @@ IS_OMAP_TYPE(3430, 0x3430)
 
 int omap_chip_is(struct omap_chip_id oci);
 void omap2_check_revision(void);
-
-#endif    /* defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) */
-- 
GitLab


From 284119c48f4a0c469b3e0237b500e536b4bc7b6f Mon Sep 17 00:00:00 2001
From: Vikram Pandita <vikram.pandita@ti.com>
Date: Mon, 10 Aug 2009 14:49:50 +0300
Subject: [PATCH 0734/1153] OMAP2/3: DMA errata correction

This errata is valid for:
OMAP2420 Errata 1.85 Impacts all 2420 ES rev
OMAP2430 Errata 1.10 Impacts only ES1.0
Description: DMA may hang when several channels are used in parallel
OMAP3430: Not impacted, so remove the errata fix for omap3

Fixed issue reported on cpu_is_omap24xx check reported by Nishant Kamat

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/plat-omap/dma.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c
index 7677a4a1cef..e3ac94f0900 100644
--- a/arch/arm/plat-omap/dma.c
+++ b/arch/arm/plat-omap/dma.c
@@ -946,7 +946,9 @@ void omap_start_dma(int lch)
 
 			cur_lch = next_lch;
 		} while (next_lch != -1);
-	} else if (cpu_class_is_omap2()) {
+	} else if (cpu_is_omap242x() ||
+		(cpu_is_omap243x() &&  omap_type() <= OMAP2430_REV_ES1_0)) {
+
 		/* Errata: Need to write lch even if not using chaining */
 		dma_write(lch, CLNK_CTRL(lch));
 	}
-- 
GitLab


From 370bc1fdefb8a30018d98aca2fdfd6b6701082e7 Mon Sep 17 00:00:00 2001
From: Janboe Ye <yuan-bo.ye@motorola.com>
Date: Mon, 10 Aug 2009 14:49:50 +0300
Subject: [PATCH 0735/1153] OMAP3: Fix omap3 sram virtual addres overlap
 vmalloc space after increasing vmalloc size

commit e85c205ac1427f2405021a36f083280ff0d0a35e increase vmalloc size.
vmalloc space will overlap with OMAP3 sram virtual address.

Signed-off-by: Li Hong Mei <hong-mei.li@motorola.com>
Signed-off-by: Janboe Ye <yuan-bo.ye@motorola.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
---
 arch/arm/plat-omap/sram.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
index 4ea73804d21..2890b11f238 100644
--- a/arch/arm/plat-omap/sram.c
+++ b/arch/arm/plat-omap/sram.c
@@ -44,9 +44,9 @@
 #define OMAP2_SRAM_VA		0xe3000000
 #define OMAP2_SRAM_PUB_VA	(OMAP2_SRAM_VA + 0x800)
 #define OMAP3_SRAM_PA           0x40200000
-#define OMAP3_SRAM_VA           0xd7000000
+#define OMAP3_SRAM_VA           0xe3000000
 #define OMAP3_SRAM_PUB_PA       0x40208000
-#define OMAP3_SRAM_PUB_VA       0xd7008000
+#define OMAP3_SRAM_PUB_VA       (OMAP3_SRAM_VA + 0x8000)
 #define OMAP4_SRAM_PA		0x40200000		/*0x402f0000*/
 #define OMAP4_SRAM_VA		0xd7000000		/*0xd70f0000*/
 
-- 
GitLab


From 5032902c331acc71956e47abd90d090181c5ef4a Mon Sep 17 00:00:00 2001
From: Sergio Aguirre <saaguirre@ti.com>
Date: Mon, 10 Aug 2009 14:49:50 +0300
Subject: [PATCH 0736/1153] OMAP3: Overo: Fix smsc911x platform device resource
 value

Fixes a wrong setting of resource parameter list in
SMSC911x platform driver data structure for Overo case.

This fixes folowing warning when compiling for Overo board:

	warning: initialization from incompatible pointer type

Introduced since commit id:
	commit 172ef275444efa12d834fb9d1b1acdac92db47f7
	Author: Steve Sakoman <sakoman@gmail.com>
	Date:   Mon Feb 2 06:27:49 2009 +0000

	    ARM: Add SMSC911X support to Overo platform (V2)

Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/board-overo.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index dff5528fbfb..fec1bb19b9f 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -146,7 +146,7 @@ static struct platform_device overo_smsc911x_device = {
 	.name		= "smsc911x",
 	.id		= -1,
 	.num_resources	= ARRAY_SIZE(overo_smsc911x_resources),
-	.resource	= &overo_smsc911x_resources,
+	.resource	= overo_smsc911x_resources,
 	.dev		= {
 		.platform_data = &overo_smsc911x_config,
 	},
-- 
GitLab


From dfc27b34496923b5f552eb9cdf20468045114ada Mon Sep 17 00:00:00 2001
From: Roger Quadros <ext-roger.quadros@nokia.com>
Date: Mon, 10 Aug 2009 14:49:51 +0300
Subject: [PATCH 0737/1153] OMAP3: RX51: Define TWL4030 USB transceiver in
 board file

Add OTG transceiver to RX51 platform data to prevent kernel NULL pointer
dereference during MUSB initialisation.

Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/board-rx51-peripherals.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index 9a0bf6744a0..56d931a425f 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -278,6 +278,10 @@ static struct twl4030_gpio_platform_data rx51_gpio_data = {
 	.setup			= rx51_twlgpio_setup,
 };
 
+static struct twl4030_usb_data rx51_usb_data = {
+	.usb_mode		= T2_USB_MODE_ULPI,
+};
+
 static struct twl4030_platform_data rx51_twldata = {
 	.irq_base		= TWL4030_IRQ_BASE,
 	.irq_end		= TWL4030_IRQ_END,
@@ -286,6 +290,7 @@ static struct twl4030_platform_data rx51_twldata = {
 	.gpio			= &rx51_gpio_data,
 	.keypad			= &rx51_kp_data,
 	.madc			= &rx51_madc_data,
+	.usb			= &rx51_usb_data,
 
 	.vaux1			= &rx51_vaux1,
 	.vaux2			= &rx51_vaux2,
-- 
GitLab


From 22833044fbe2764d44ae03f58508e671652ca186 Mon Sep 17 00:00:00 2001
From: Roger Quadros <ext-roger.quadros@nokia.com>
Date: Mon, 10 Aug 2009 14:49:51 +0300
Subject: [PATCH 0738/1153] OMAP2/3: mmc-twl4030: Free up MMC regulators while
 cleaning up

twl_mmc_cleanup() must free up the regulators that were
allocated by twl_mmc_late_init().
This eliminates the below error when 'omap_hsmmc' module is
repeatedly loaded and unloaded.

"sysfs: cannot create duplicate filename '/devices/platform
 /mmci-omap-hs.0/microamps_requested_vmmc'"

Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/mach-omap2/mmc-twl4030.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/mach-omap2/mmc-twl4030.c b/arch/arm/mach-omap2/mmc-twl4030.c
index 1541fd4c8d0..3c04c2f1b23 100644
--- a/arch/arm/mach-omap2/mmc-twl4030.c
+++ b/arch/arm/mach-omap2/mmc-twl4030.c
@@ -119,6 +119,7 @@ static int twl_mmc_late_init(struct device *dev)
 				if (i != 0)
 					break;
 				ret = PTR_ERR(reg);
+				hsmmc[i].vcc = NULL;
 				goto err;
 			}
 			hsmmc[i].vcc = reg;
@@ -165,8 +166,13 @@ done:
 static void twl_mmc_cleanup(struct device *dev)
 {
 	struct omap_mmc_platform_data *mmc = dev->platform_data;
+	int i;
 
 	gpio_free(mmc->slots[0].switch_pin);
+	for(i = 0; i < ARRAY_SIZE(hsmmc); i++) {
+		regulator_put(hsmmc[i].vcc);
+		regulator_put(hsmmc[i].vcc_aux);
+	}
 }
 
 #ifdef CONFIG_PM
-- 
GitLab


From 4177662ec9f5e50b69ef074369fdb429dd48d97e Mon Sep 17 00:00:00 2001
From: Roger Quadros <ext-roger.quadros@nokia.com>
Date: Mon, 10 Aug 2009 14:49:52 +0300
Subject: [PATCH 0739/1153] OMAP3: RX51: Updated rx51_defconfig

Added REGULATOR, MMC and updated default CMDLINE so RX51 now boots.

Note that the regulator code should be moved from mmc-twl4030.c
to omap_hsmmc.c so it can be a module.

Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 arch/arm/configs/rx51_defconfig | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/arch/arm/configs/rx51_defconfig b/arch/arm/configs/rx51_defconfig
index eb2cb31825c..f238df66efd 100644
--- a/arch/arm/configs/rx51_defconfig
+++ b/arch/arm/configs/rx51_defconfig
@@ -282,7 +282,7 @@ CONFIG_ALIGNMENT_TRAP=y
 #
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0"
+CONFIG_CMDLINE="init=/sbin/preinit ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs rootflags=bulk_read,no_chk_data_crc rw console=ttyMTD,log console=tty0 console=ttyS2,115200n8"
 # CONFIG_XIP_KERNEL is not set
 # CONFIG_KEXEC is not set
 
@@ -1354,7 +1354,7 @@ CONFIG_USB_OTG_UTILS=y
 # CONFIG_USB_GPIO_VBUS is not set
 # CONFIG_ISP1301_OMAP is not set
 CONFIG_TWL4030_USB=y
-CONFIG_MMC=m
+CONFIG_MMC=y
 # CONFIG_MMC_DEBUG is not set
 # CONFIG_MMC_UNSAFE_RESUME is not set
 
@@ -1449,7 +1449,8 @@ CONFIG_RTC_DRV_TWL4030=m
 # on-CPU RTC drivers
 #
 # CONFIG_DMADEVICES is not set
-# CONFIG_REGULATOR is not set
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_TWL4030=y
 # CONFIG_UIO is not set
 # CONFIG_STAGING is not set
 
-- 
GitLab


From 2fc391112fb6f3424435a3aa2fda887497b5f807 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <peterz@infradead.org>
Date: Mon, 10 Aug 2009 12:33:05 +0100
Subject: [PATCH 0740/1153] locking, sched: Give waitqueue spinlocks their own
 lockdep classes

Give waitqueue spinlocks their own lockdep classes when they
are initialised from init_waitqueue_head().  This means that
struct wait_queue::func functions can operate other waitqueues.

This is used by CacheFiles to catch the page from a backing fs
being unlocked and to wake up another thread to take a copy of
it.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: linux-cachefs@redhat.com
Cc: torvalds@osdl.org
Cc: akpm@linux-foundation.org
LKML-Reference: <20090810113305.17284.81508.stgit@warthog.procyon.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 include/linux/wait.h | 9 ++++++++-
 kernel/wait.c        | 5 +++--
 2 files changed, 11 insertions(+), 3 deletions(-)

diff --git a/include/linux/wait.h b/include/linux/wait.h
index 6788e1a4d4c..cf3c2f5dba5 100644
--- a/include/linux/wait.h
+++ b/include/linux/wait.h
@@ -77,7 +77,14 @@ struct task_struct;
 #define __WAIT_BIT_KEY_INITIALIZER(word, bit)				\
 	{ .flags = word, .bit_nr = bit, }
 
-extern void init_waitqueue_head(wait_queue_head_t *q);
+extern void __init_waitqueue_head(wait_queue_head_t *q, struct lock_class_key *);
+
+#define init_waitqueue_head(q)				\
+	do {						\
+		static struct lock_class_key __key;	\
+							\
+		__init_waitqueue_head((q), &__key);	\
+	} while (0)
 
 #ifdef CONFIG_LOCKDEP
 # define __WAIT_QUEUE_HEAD_INIT_ONSTACK(name) \
diff --git a/kernel/wait.c b/kernel/wait.c
index ea7c3b4275c..c4bd3d825f3 100644
--- a/kernel/wait.c
+++ b/kernel/wait.c
@@ -10,13 +10,14 @@
 #include <linux/wait.h>
 #include <linux/hash.h>
 
-void init_waitqueue_head(wait_queue_head_t *q)
+void __init_waitqueue_head(wait_queue_head_t *q, struct lock_class_key *key)
 {
 	spin_lock_init(&q->lock);
+	lockdep_set_class(&q->lock, key);
 	INIT_LIST_HEAD(&q->task_list);
 }
 
-EXPORT_SYMBOL(init_waitqueue_head);
+EXPORT_SYMBOL(__init_waitqueue_head);
 
 void add_wait_queue(wait_queue_head_t *q, wait_queue_t *wait)
 {
-- 
GitLab


From 4dc88029fd916b860ef063c40180aa604ce93494 Mon Sep 17 00:00:00 2001
From: Dinakar Guniguntala <dino@in.ibm.com>
Date: Mon, 10 Aug 2009 18:31:42 +0530
Subject: [PATCH 0741/1153] futex: Fix compat_futex to be same as futex for
 REQUEUE_PI

Need to add the REQUEUE_PI checks to the compat_sys_futex API
as well to ensure 32 bit requeue's work fine on a 64 bit
system. Patch is against latest tip

Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Cc: Darren Hart <dvhltc@us.ibm.com>
LKML-Reference: <20090810130142.GA23619@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/futex_compat.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/kernel/futex_compat.c b/kernel/futex_compat.c
index d607a5b9ee2..235716556bf 100644
--- a/kernel/futex_compat.c
+++ b/kernel/futex_compat.c
@@ -180,7 +180,8 @@ asmlinkage long compat_sys_futex(u32 __user *uaddr, int op, u32 val,
 	int cmd = op & FUTEX_CMD_MASK;
 
 	if (utime && (cmd == FUTEX_WAIT || cmd == FUTEX_LOCK_PI ||
-		      cmd == FUTEX_WAIT_BITSET)) {
+		      cmd == FUTEX_WAIT_BITSET ||
+		      cmd == FUTEX_WAIT_REQUEUE_PI)) {
 		if (get_compat_timespec(&ts, utime))
 			return -EFAULT;
 		if (!timespec_valid(&ts))
@@ -191,7 +192,8 @@ asmlinkage long compat_sys_futex(u32 __user *uaddr, int op, u32 val,
 			t = ktime_add_safe(ktime_get(), t);
 		tp = &t;
 	}
-	if (cmd == FUTEX_REQUEUE || cmd == FUTEX_CMP_REQUEUE)
+	if (cmd == FUTEX_REQUEUE || cmd == FUTEX_CMP_REQUEUE ||
+	    cmd == FUTEX_CMP_REQUEUE_PI || cmd == FUTEX_WAKE_OP)
 		val2 = (int) (unsigned long) utime;
 
 	return do_futex(uaddr, op, val, tp, uaddr2, val2, val3);
-- 
GitLab


From 304703aba31a87903b8c0db8f5e6890cac2d596d Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Mon, 10 Aug 2009 16:11:32 +0200
Subject: [PATCH 0742/1153] perf_counter: Subtract the buffer size field from
 the event record size

We compute the perf raw sample size by aligning the raw ftrace
event size plus the buffer size field itself. We do that
instead of aligning only the perf raw sample size, so that we
might economize some in some cases.

But this buffer size field is not stored in the perf raw
sample, we must then substract its size from the buffer once we
computed the alignment unless we may get a useless u32 field in
the buffer.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090810141129.GA5124@nowhere>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 include/trace/ftrace.h | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/include/trace/ftrace.h b/include/trace/ftrace.h
index 7167b9b97da..a05524fa245 100644
--- a/include/trace/ftrace.h
+++ b/include/trace/ftrace.h
@@ -637,7 +637,12 @@ __attribute__((section("_ftrace_events"))) event_##call = {		\
  *	pc = preempt_count();
  *
  *	__data_size = ftrace_get_offsets_<call>(&__data_offsets, args);
- *	__entry_size = __data_size + sizeof(*entry);
+ *
+ *	// Below we want to get the aligned size by taking into account
+ *	// the u32 field that will later store the buffer size
+ *	__entry_size = ALIGN(__data_size + sizeof(*entry) + sizeof(u32),
+ *			     sizeof(u64));
+ *	__entry_size -= sizeof(u32);
  *
  *	do {
  *		char raw_data[__entry_size]; <- allocate our sample in the stack
@@ -687,6 +692,7 @@ static void ftrace_profile_##call(proto)				\
 	__data_size = ftrace_get_offsets_##call(&__data_offsets, args); \
 	__entry_size = ALIGN(__data_size + sizeof(*entry) + sizeof(u32),\
 			     sizeof(u64));				\
+	__entry_size -= sizeof(u32);					\
 									\
 	do {								\
 		char raw_data[__entry_size];				\
-- 
GitLab


From 1853db0e02ae4088f102b0d8e59e83dc98f93f03 Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Mon, 10 Aug 2009 16:38:36 +0200
Subject: [PATCH 0743/1153] perf_counter: Zero dead bytes from ftrace raw
 samples size alignment

After aligning the ftrace raw samples, there are dead bytes storing
random data from the stack. We don't want to leak these to userspace,
then zero these out.

Before:

	0x2de88 [0x50]: event: 9
	.
	. ... raw event: size 80 bytes
	.  0000:  09 00 00 00 01 00 50 00 d0 c7 00 81 ff ff ff ff  ......P........
	.  0010:  68 01 00 00 68 01 00 00 2c 00 00 00 00 00 00 00  h...h...,......
	.  0020:  2c 00 00 00 2b 00 01 02 68 01 00 00 68 01 00 00  ,...+...h...h..
	.  0030:  6b 6f 6e 64 65 6d 61 6e 64 2f 30 00 00 00 00 00  kondemand/0....
	.  0040:  68 01 00 00 40 7f 46 81 ff ff ff ff 00 10 1b 7f  h...@.F........
                                                      ^  ^  ^  ^
                                                         Leak

After:

	0x2d318 [0x50]: event: 9
	.
	. ... raw event: size 80 bytes
	.  0000:  09 00 00 00 01 00 50 00 d0 c7 00 81 ff ff ff ff  ......P........
	.  0010:  68 01 00 00 68 01 00 00 68 14 00 00 00 00 00 00  h...h...h......
	.  0020:  2c 00 00 00 2b 00 01 02 68 01 00 00 68 01 00 00  ,...+...h...h..
	.  0030:  6b 6f 6e 64 65 6d 61 6e 64 2f 30 00 00 00 00 00  kondemand/0....
	.  0040:  68 01 00 00 a0 80 46 81 ff ff ff ff 00 00 00 00  h.....F........
                                                      ^  ^  ^  ^
							 Fixed

Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1249915116-5210-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
---
 include/trace/ftrace.h | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/include/trace/ftrace.h b/include/trace/ftrace.h
index a05524fa245..f64fbaae781 100644
--- a/include/trace/ftrace.h
+++ b/include/trace/ftrace.h
@@ -648,6 +648,9 @@ __attribute__((section("_ftrace_events"))) event_##call = {		\
  *		char raw_data[__entry_size]; <- allocate our sample in the stack
  *		struct trace_entry *ent;
  *
+ *		zero dead bytes from alignment to avoid stack leak to userspace:
+ *
+ *		*(u64 *)(&raw_data[__entry_size - sizeof(u64)]) = 0ULL;
  *		entry = (struct ftrace_raw_<call> *)raw_data;
  *		ent = &entry->ent;
  *		tracing_generic_entry_update(ent, irq_flags, pc);
@@ -698,6 +701,7 @@ static void ftrace_profile_##call(proto)				\
 		char raw_data[__entry_size];				\
 		struct trace_entry *ent;				\
 									\
+		*(u64 *)(&raw_data[__entry_size - sizeof(u64)]) = 0ULL;	\
 		entry = (struct ftrace_raw_##call *)raw_data;		\
 		ent = &entry->ent;					\
 		tracing_generic_entry_update(ent, irq_flags, pc);	\
-- 
GitLab


From 1392e3b33319fd1a2527bebfc56631c2f2d3c7c5 Mon Sep 17 00:00:00 2001
From: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Date: Sat, 8 Aug 2009 17:52:50 +0900
Subject: [PATCH 0744/1153] documentation: register ioctl entry of nilfs2

This will register the ioctl range used by nilfs2 file system to the
table listed in Documentation/ioctl/ioctl-number.txt.

Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 Documentation/ioctl/ioctl-number.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/ioctl/ioctl-number.txt b/Documentation/ioctl/ioctl-number.txt
index 7bb0d934b6d..dbea4f95fc8 100644
--- a/Documentation/ioctl/ioctl-number.txt
+++ b/Documentation/ioctl/ioctl-number.txt
@@ -139,6 +139,7 @@ Code	Seq#	Include File		Comments
 'm'	all	linux/synclink.h	conflict!
 'm'	00-1F	net/irda/irmod.h	conflict!
 'n'	00-7F	linux/ncp_fs.h
+'n'	80-8F	linux/nilfs2_fs.h	NILFS2
 'n'	E0-FF	video/matrox.h          matroxfb
 'o'	00-1F	fs/ocfs2/ocfs2_fs.h	OCFS2
 'o'     00-03   include/mtd/ubi-user.h  conflict! (OCFS2 and UBI overlaps)
-- 
GitLab


From 5e2f89b5d5d87a7c3ba19fc85ba0c29adb65f639 Mon Sep 17 00:00:00 2001
From: "Figo.zhang" <figo1802@gmail.com>
Date: Sat, 8 Aug 2009 21:01:22 +0800
Subject: [PATCH 0745/1153] mempool.c: clean up type-casting

clean up type-casting twice.  "size_t" is typedef as "unsigned long" in
64-bit system, and "unsigned int" in 32-bit system, and the intermediate
cast to 'long' is pointless.

Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 mm/mempool.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/mm/mempool.c b/mm/mempool.c
index a46eb1b4bb6..32e75d40050 100644
--- a/mm/mempool.c
+++ b/mm/mempool.c
@@ -303,14 +303,14 @@ EXPORT_SYMBOL(mempool_free_slab);
  */
 void *mempool_kmalloc(gfp_t gfp_mask, void *pool_data)
 {
-	size_t size = (size_t)(long)pool_data;
+	size_t size = (size_t)pool_data;
 	return kmalloc(size, gfp_mask);
 }
 EXPORT_SYMBOL(mempool_kmalloc);
 
 void *mempool_kzalloc(gfp_t gfp_mask, void *pool_data)
 {
-	size_t size = (size_t) pool_data;
+	size_t size = (size_t)pool_data;
 	return kzalloc(size, gfp_mask);
 }
 EXPORT_SYMBOL(mempool_kzalloc);
-- 
GitLab


From 04e35357e2e3ff4e0cabd6468354cf3dbfeb4f27 Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <jaswinder@kernel.org>
Date: Mon, 10 Aug 2009 16:45:42 +0100
Subject: [PATCH 0746/1153] MN10300: includecheck fix: mn10300, pci.h

Fix the following 'make includecheck' warning:

  arch/mn10300/include/asm/pci.h: linux/mm.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 arch/mn10300/include/asm/pci.h | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/mn10300/include/asm/pci.h b/arch/mn10300/include/asm/pci.h
index 35d2ed6396f..19aecc90f7a 100644
--- a/arch/mn10300/include/asm/pci.h
+++ b/arch/mn10300/include/asm/pci.h
@@ -59,7 +59,6 @@ void pcibios_penalize_isa_irq(int irq);
 #include <linux/slab.h>
 #include <asm/scatterlist.h>
 #include <linux/string.h>
-#include <linux/mm.h>
 #include <asm/io.h>
 
 struct pci_dev;
-- 
GitLab


From b6e61eef4f9f94714ac3ee4a5c96862d9bcd1836 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Fri, 31 Jul 2009 12:45:41 -0700
Subject: [PATCH 0747/1153] x86: Fix serialization in pit_expect_msb()

Wei Chong Tan reported a fast-PIT-calibration corner-case:

| pit_expect_msb() is vulnerable to SMI disturbance corner case
| in some platforms which causes /proc/cpuinfo to show wrong
| CPU MHz value when quick_pit_calibrate() jumps to success
| section.

I think that the real issue isn't even an SMI - but the fact
that in the very last iteration of the loop, there's no
serializing instruction _after_ the last 'rdtsc'. So even in
the absense of SMI's, we do have a situation where the cycle
counter was read without proper serialization.

The last check should be done outside the outer loop, since
_inside_ the outer loop, we'll be testing that the PIT has
the right MSB value has the right value in the next iteration.

So only the _last_ iteration is special, because that's the one
that will not check the PIT MSB value any more, and because the
final 'get_cycles()' isn't serialized.

In other words:

 - I'd like to move the PIT MSB check to after the last
   iteration, rather than in every iteration

 - I think we should comment on the fact that it's also a
   serializing instruction and so 'fences in' the TSC read.

Here's a suggested replacement.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
Tested-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
LKML-Reference: <B28277FD4E0F9247A3D55704C440A140D5D683F3@pgsmsx504.gar.corp.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/tsc.c | 29 ++++++++++++++++++++++-------
 1 file changed, 22 insertions(+), 7 deletions(-)

diff --git a/arch/x86/kernel/tsc.c b/arch/x86/kernel/tsc.c
index 6e1a368d21d..71f4368b357 100644
--- a/arch/x86/kernel/tsc.c
+++ b/arch/x86/kernel/tsc.c
@@ -275,15 +275,20 @@ static unsigned long pit_calibrate_tsc(u32 latch, unsigned long ms, int loopmin)
  * use the TSC value at the transitions to calculate a pretty
  * good value for the TSC frequencty.
  */
+static inline int pit_verify_msb(unsigned char val)
+{
+	/* Ignore LSB */
+	inb(0x42);
+	return inb(0x42) == val;
+}
+
 static inline int pit_expect_msb(unsigned char val, u64 *tscp, unsigned long *deltap)
 {
 	int count;
 	u64 tsc = 0;
 
 	for (count = 0; count < 50000; count++) {
-		/* Ignore LSB */
-		inb(0x42);
-		if (inb(0x42) != val)
+		if (!pit_verify_msb(val))
 			break;
 		tsc = get_cycles();
 	}
@@ -336,8 +341,7 @@ static unsigned long quick_pit_calibrate(void)
 	 * to do that is to just read back the 16-bit counter
 	 * once from the PIT.
 	 */
-	inb(0x42);
-	inb(0x42);
+	pit_verify_msb(0);
 
 	if (pit_expect_msb(0xff, &tsc, &d1)) {
 		for (i = 1; i <= MAX_QUICK_PIT_ITERATIONS; i++) {
@@ -348,8 +352,19 @@ static unsigned long quick_pit_calibrate(void)
 			 * Iterate until the error is less than 500 ppm
 			 */
 			delta -= tsc;
-			if (d1+d2 < delta >> 11)
-				goto success;
+			if (d1+d2 >= delta >> 11)
+				continue;
+
+			/*
+			 * Check the PIT one more time to verify that
+			 * all TSC reads were stable wrt the PIT.
+			 *
+			 * This also guarantees serialization of the
+			 * last cycle read ('d2') in pit_expect_msb.
+			 */
+			if (!pit_verify_msb(0xfe - i))
+				break;
+			goto success;
 		}
 	}
 	printk("Fast TSC calibration failed\n");
-- 
GitLab


From 392741e0a4e17c82e3978b7fcbf04291294dc0a1 Mon Sep 17 00:00:00 2001
From: Darren Hart <dvhltc@us.ibm.com>
Date: Fri, 7 Aug 2009 15:20:48 -0700
Subject: [PATCH 0748/1153] futex: Fix handling of bad requeue syscall pairing

If futex_requeue(requeue_pi=1) finds a futex_q that was created by a call
other the futex_wait_requeue_pi(), the q.rt_waiter may be null.  If so,
this will result in an oops from the following call graph:

futex_requeue()
  rt_mutex_start_proxy_lock()
    task_blocks_on_rt_mutex()
      waiter->task dereference
        OOPS

We currently WARN_ON() if this is detected, clearly this is inadequate.
If we detect a mispairing in futex_requeue(), bail out, seding -EINVAL to
user-space.

V2: Fix parenthesis warnings.

Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: John Kacur <jkacur@redhat.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dinakar Guniguntala <dino@in.ibm.com>
Cc: John Stultz <johnstul@linux.vnet.ibm.com>
LKML-Reference: <4A7CA8C0.7010809@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/futex.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/kernel/futex.c b/kernel/futex.c
index 8cc3ee1363a..e18cfbdc719 100644
--- a/kernel/futex.c
+++ b/kernel/futex.c
@@ -1256,8 +1256,15 @@ retry_private:
 		if (!match_futex(&this->key, &key1))
 			continue;
 
-		WARN_ON(!requeue_pi && this->rt_waiter);
-		WARN_ON(requeue_pi && !this->rt_waiter);
+		/*
+		 * FUTEX_WAIT_REQEUE_PI and FUTEX_CMP_REQUEUE_PI should always
+		 * be paired with each other and no other futex ops.
+		 */
+		if ((requeue_pi && !this->rt_waiter) ||
+		    (!requeue_pi && this->rt_waiter)) {
+			ret = -EINVAL;
+			break;
+		}
 
 		/*
 		 * Wake nr_wake waiters.  For requeue_pi, if we acquired the
-- 
GitLab


From 3e03bbeac541856aaaf1ce1ab0250b6a490e4099 Mon Sep 17 00:00:00 2001
From: Shunichi Fuji <palglowr@gmail.com>
Date: Tue, 11 Aug 2009 03:34:40 +0900
Subject: [PATCH 0749/1153] x86: Add reboot quirk for every 5 series
 MacBook/Pro
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Reboot does not work on my MacBook Pro 13 inch (MacBookPro5,5)
too. It seems all unibody MacBook and MacBookPro require
PCI reboot handling, i guess.

Following model/machine ID list shows unibody MacBook/Pro have
the 5 series of model number:

   http://www.everymac.com/systems/by_capability/macs-by-machine-model-machine-id.html

Signed-off-by: Shunichi Fuji <palglowr@gmail.com>
Cc: Ozan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <30046e3b0908101134p6487ddbftd8776e4ddef204be@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/reboot.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/x86/kernel/reboot.c b/arch/x86/kernel/reboot.c
index 9eb89760370..a06e8d10184 100644
--- a/arch/x86/kernel/reboot.c
+++ b/arch/x86/kernel/reboot.c
@@ -418,20 +418,20 @@ static int __init set_pci_reboot(const struct dmi_system_id *d)
 }
 
 static struct dmi_system_id __initdata pci_reboot_dmi_table[] = {
-	{	/* Handle problems with rebooting on Apple MacBook5,2 */
+	{	/* Handle problems with rebooting on Apple MacBook5 */
 		.callback = set_pci_reboot,
-		.ident = "Apple MacBook",
+		.ident = "Apple MacBook5",
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
-			DMI_MATCH(DMI_PRODUCT_NAME, "MacBook5,2"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MacBook5"),
 		},
 	},
-	{	/* Handle problems with rebooting on Apple MacBookPro5,1 */
+	{	/* Handle problems with rebooting on Apple MacBookPro5 */
 		.callback = set_pci_reboot,
-		.ident = "Apple MacBookPro5,1",
+		.ident = "Apple MacBookPro5",
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
-			DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro5,1"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro5"),
 		},
 	},
 	{ }
-- 
GitLab


From b409d7a0ab46fe530efe52734984b4ed5d46c3eb Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Thu, 6 Aug 2009 23:29:34 +0200
Subject: [PATCH 0750/1153] ocfs2: Fix possible deadlock when extending quota
 file

In OCFS2, allocator locks rank above transaction start. Thus we
cannot extend quota file from inside a transaction less we could
deadlock.

We solve the problem by starting transaction not already in
ocfs2_acquire_dquot() but only in ocfs2_local_read_dquot() and
ocfs2_global_read_dquot() and we allocate blocks to quota files before starting
the transaction.  In case we crash, quota files will just have a few blocks
more but that's no problem since we just use them next time we extend the
quota file.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/journal.h      |   5 --
 fs/ocfs2/quota_global.c | 115 ++++++++++++++++++++--------------------
 2 files changed, 57 insertions(+), 63 deletions(-)

diff --git a/fs/ocfs2/journal.h b/fs/ocfs2/journal.h
index 4a4d3b55fd2..2c3222aec62 100644
--- a/fs/ocfs2/journal.h
+++ b/fs/ocfs2/journal.h
@@ -363,11 +363,6 @@ static inline int ocfs2_quota_trans_credits(struct super_block *sb)
 	return credits;
 }
 
-/* Number of credits needed for removing quota structure from file */
-int ocfs2_calc_qdel_credits(struct super_block *sb, int type);
-/* Number of credits needed for initialization of new quota structure */
-int ocfs2_calc_qinit_credits(struct super_block *sb, int type);
-
 /* group extend. inode update and last group update. */
 #define OCFS2_GROUP_EXTEND_CREDITS	(OCFS2_INODE_UPDATE_CREDITS + 1)
 
diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c
index d604a6aa0a2..bf7742d0ee3 100644
--- a/fs/ocfs2/quota_global.c
+++ b/fs/ocfs2/quota_global.c
@@ -215,11 +215,7 @@ ssize_t ocfs2_quota_write(struct super_block *sb, int type,
 		loff_t rounded_end =
 				ocfs2_align_bytes_to_blocks(sb, off + len);
 
-		down_write(&OCFS2_I(gqinode)->ip_alloc_sem);
-		err = ocfs2_extend_no_holes(gqinode, rounded_end, off);
-		up_write(&OCFS2_I(gqinode)->ip_alloc_sem);
-		if (err < 0)
-			goto out;
+		/* Space is already allocated in ocfs2_global_read_dquot() */
 		err = ocfs2_simple_size_update(gqinode,
 					       oinfo->dqi_gqi_bh,
 					       rounded_end);
@@ -405,13 +401,36 @@ int ocfs2_global_write_info(struct super_block *sb, int type)
 	return err;
 }
 
+static int ocfs2_global_qinit_alloc(struct super_block *sb, int type)
+{
+	struct ocfs2_mem_dqinfo *oinfo = sb_dqinfo(sb, type)->dqi_priv;
+
+	/*
+	 * We may need to allocate tree blocks and a leaf block but not the
+	 * root block
+	 */
+	return oinfo->dqi_gi.dqi_qtree_depth;
+}
+
+static int ocfs2_calc_global_qinit_credits(struct super_block *sb, int type)
+{
+	/* We modify all the allocated blocks, tree root, and info block */
+	return (ocfs2_global_qinit_alloc(sb, type) + 2) *
+			OCFS2_QUOTA_BLOCK_UPDATE_CREDITS;
+}
+
 /* Read in information from global quota file and acquire a reference to it.
  * dquot_acquire() has already started the transaction and locked quota file */
 int ocfs2_global_read_dquot(struct dquot *dquot)
 {
 	int err, err2, ex = 0;
-	struct ocfs2_mem_dqinfo *info =
-			sb_dqinfo(dquot->dq_sb, dquot->dq_type)->dqi_priv;
+	struct super_block *sb = dquot->dq_sb;
+	int type = dquot->dq_type;
+	struct ocfs2_mem_dqinfo *info = sb_dqinfo(sb, type)->dqi_priv;
+	struct ocfs2_super *osb = OCFS2_SB(sb);
+	struct inode *gqinode = info->dqi_gqinode;
+	int need_alloc = ocfs2_global_qinit_alloc(sb, type);
+	handle_t *handle = NULL;
 
 	err = ocfs2_qinfo_lock(info, 0);
 	if (err < 0)
@@ -422,14 +441,33 @@ int ocfs2_global_read_dquot(struct dquot *dquot)
 	OCFS2_DQUOT(dquot)->dq_use_count++;
 	OCFS2_DQUOT(dquot)->dq_origspace = dquot->dq_dqb.dqb_curspace;
 	OCFS2_DQUOT(dquot)->dq_originodes = dquot->dq_dqb.dqb_curinodes;
+	ocfs2_qinfo_unlock(info, 0);
+
 	if (!dquot->dq_off) {	/* No real quota entry? */
-		/* Upgrade to exclusive lock for allocation */
-		ocfs2_qinfo_unlock(info, 0);
-		err = ocfs2_qinfo_lock(info, 1);
-		if (err < 0)
-			goto out_qlock;
 		ex = 1;
+		/*
+		 * Add blocks to quota file before we start a transaction since
+		 * locking allocators ranks above a transaction start
+		 */
+		WARN_ON(journal_current_handle());
+		down_write(&OCFS2_I(gqinode)->ip_alloc_sem);
+		err = ocfs2_extend_no_holes(gqinode,
+			gqinode->i_size + (need_alloc << sb->s_blocksize_bits),
+			gqinode->i_size);
+		up_write(&OCFS2_I(gqinode)->ip_alloc_sem);
+		if (err < 0)
+			goto out;
+	}
+
+	handle = ocfs2_start_trans(osb,
+				   ocfs2_calc_global_qinit_credits(sb, type));
+	if (IS_ERR(handle)) {
+		err = PTR_ERR(handle);
+		goto out;
 	}
+	err = ocfs2_qinfo_lock(info, ex);
+	if (err < 0)
+		goto out_trans;
 	err = qtree_write_dquot(&info->dqi_gi, dquot);
 	if (ex && info_dirty(sb_dqinfo(dquot->dq_sb, dquot->dq_type))) {
 		err2 = __ocfs2_global_write_info(dquot->dq_sb, dquot->dq_type);
@@ -441,6 +479,9 @@ out_qlock:
 		ocfs2_qinfo_unlock(info, 1);
 	else
 		ocfs2_qinfo_unlock(info, 0);
+out_trans:
+	if (handle)
+		ocfs2_commit_trans(osb, handle);
 out:
 	if (err < 0)
 		mlog_errno(err);
@@ -638,24 +679,17 @@ out:
 	return status;
 }
 
-int ocfs2_calc_qdel_credits(struct super_block *sb, int type)
+static int ocfs2_calc_qdel_credits(struct super_block *sb, int type)
 {
-	struct ocfs2_mem_dqinfo *oinfo;
-	int features[MAXQUOTAS] = { OCFS2_FEATURE_RO_COMPAT_USRQUOTA,
-				    OCFS2_FEATURE_RO_COMPAT_GRPQUOTA };
-
-	if (!OCFS2_HAS_RO_COMPAT_FEATURE(sb, features[type]))
-		return 0;
-
-	oinfo = sb_dqinfo(sb, type)->dqi_priv;
+	struct ocfs2_mem_dqinfo *oinfo = sb_dqinfo(sb, type)->dqi_priv;
 	/*
 	 * We modify tree, leaf block, global info, local chunk header,
 	 * global and local inode; OCFS2_QINFO_WRITE_CREDITS already
 	 * accounts for inode update
 	 */
-	return oinfo->dqi_gi.dqi_qtree_depth +
+	return (oinfo->dqi_gi.dqi_qtree_depth + 2) *
+	       OCFS2_QUOTA_BLOCK_UPDATE_CREDITS +
 	       OCFS2_QINFO_WRITE_CREDITS +
-	       2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS +
 	       OCFS2_INODE_UPDATE_CREDITS;
 }
 
@@ -688,36 +722,10 @@ out:
 	return status;
 }
 
-int ocfs2_calc_qinit_credits(struct super_block *sb, int type)
-{
-	struct ocfs2_mem_dqinfo *oinfo;
-	int features[MAXQUOTAS] = { OCFS2_FEATURE_RO_COMPAT_USRQUOTA,
-				    OCFS2_FEATURE_RO_COMPAT_GRPQUOTA };
-	struct ocfs2_dinode *lfe, *gfe;
-
-	if (!OCFS2_HAS_RO_COMPAT_FEATURE(sb, features[type]))
-		return 0;
-
-	oinfo = sb_dqinfo(sb, type)->dqi_priv;
-	gfe = (struct ocfs2_dinode *)oinfo->dqi_gqi_bh->b_data;
-	lfe = (struct ocfs2_dinode *)oinfo->dqi_lqi_bh->b_data;
-	/* We can extend local file + global file. In local file we
-	 * can modify info, chunk header block and dquot block. In
-	 * global file we can modify info, tree and leaf block */
-	return ocfs2_calc_extend_credits(sb, &lfe->id2.i_list, 0) +
-	       ocfs2_calc_extend_credits(sb, &gfe->id2.i_list, 0) +
-	       OCFS2_LOCAL_QINFO_WRITE_CREDITS +
-	       2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS +
-	       oinfo->dqi_gi.dqi_qtree_depth +
-	       2 * OCFS2_QUOTA_BLOCK_UPDATE_CREDITS;
-}
-
 static int ocfs2_acquire_dquot(struct dquot *dquot)
 {
-	handle_t *handle;
 	struct ocfs2_mem_dqinfo *oinfo =
 			sb_dqinfo(dquot->dq_sb, dquot->dq_type)->dqi_priv;
-	struct ocfs2_super *osb = OCFS2_SB(dquot->dq_sb);
 	int status = 0;
 
 	mlog_entry("id=%u, type=%d", dquot->dq_id, dquot->dq_type);
@@ -726,16 +734,7 @@ static int ocfs2_acquire_dquot(struct dquot *dquot)
 	status = ocfs2_lock_global_qf(oinfo, 1);
 	if (status < 0)
 		goto out;
-	handle = ocfs2_start_trans(osb,
-		ocfs2_calc_qinit_credits(dquot->dq_sb, dquot->dq_type));
-	if (IS_ERR(handle)) {
-		status = PTR_ERR(handle);
-		mlog_errno(status);
-		goto out_ilock;
-	}
 	status = dquot_acquire(dquot);
-	ocfs2_commit_trans(osb, handle);
-out_ilock:
 	ocfs2_unlock_global_qf(oinfo, 1);
 out:
 	mlog_exit(status);
-- 
GitLab


From 85dfd81dc57e8183a277ddd7a56aa65c96f3f487 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Mon, 10 Aug 2009 13:21:19 -0700
Subject: [PATCH 0751/1153] pty: fix data loss when stopped (^S/^Q)

Commit d945cb9cc ("pty: Rework the pty layer to use the normal buffering
logic") dropped the test for 'tty->stopped' in pty_write_room(), which
then causes the n_tty line discipline thing to not throttle the data
properly when the tty is stopped.

So instead of pausing the write due to the tty being stopped, the ldisc
layer would go ahead and push it down to the pty.  The pty write()
routine would then refuse to take the data (because it _did_ check
'stopped'), and the data wouldn't actually be written.

This whole stopped test should eventually be moved into the tty ldisc
layer rather than have low-level tty drivers care about these things,
but right now the fix is to just re-instate the missing pty 'stopped'
handling.

Reported-and-tested-by: Artur Skawina <art.08.09@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/char/pty.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/char/pty.c b/drivers/char/pty.c
index 6e6942c45f5..d083c73d784 100644
--- a/drivers/char/pty.c
+++ b/drivers/char/pty.c
@@ -144,6 +144,8 @@ static int pty_write(struct tty_struct *tty, const unsigned char *buf,
 
 static int pty_write_room(struct tty_struct *tty)
 {
+	if (tty->stopped)
+		return 0;
 	return pty_space(tty->link);
 }
 
-- 
GitLab


From 363ec5614f86110c6a6bdd72ac2147ebafd3ff5e Mon Sep 17 00:00:00 2001
From: Christian Lamparter <chunkeey@web.de>
Date: Sat, 8 Aug 2009 17:09:48 +0200
Subject: [PATCH 0752/1153] ar9170usb: fix spurious firmware related message

When ar9170-2.fw was missing, the driver erroneously complained
about missing the initialization values file ar9170-1.fw...

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/ath/ar9170/usb.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ar9170/usb.c b/drivers/net/wireless/ath/ar9170/usb.c
index 754b1f8d8da..007eb85fc67 100644
--- a/drivers/net/wireless/ath/ar9170/usb.c
+++ b/drivers/net/wireless/ath/ar9170/usb.c
@@ -598,11 +598,15 @@ static int ar9170_usb_request_firmware(struct ar9170_usb *aru)
 
 	err = request_firmware(&aru->init_values, "ar9170-1.fw",
 			       &aru->udev->dev);
+	if (err) {
+		dev_err(&aru->udev->dev, "file with init values not found.\n");
+		return err;
+	}
 
 	err = request_firmware(&aru->firmware, "ar9170-2.fw", &aru->udev->dev);
 	if (err) {
 		release_firmware(aru->init_values);
-		dev_err(&aru->udev->dev, "file with init values not found.\n");
+		dev_err(&aru->udev->dev, "firmware file not found.\n");
 		return err;
 	}
 
-- 
GitLab


From e9d126cdfa60b575f1b5b02024c4faee27dccf07 Mon Sep 17 00:00:00 2001
From: Dan Carpenter <error27@gmail.com>
Date: Sun, 9 Aug 2009 14:24:09 +0200
Subject: [PATCH 0753/1153] ar9170: fix read & write outside array bounds

queue == __AR9170_NUM_TXQ would cause a bug on the next line.

found by Smatch ( http://repo.or.cz/w/smatch.git ).

Cc: stable@kernel.org
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/ath/ar9170/main.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/ath/ar9170/main.c b/drivers/net/wireless/ath/ar9170/main.c
index 9d38cf60a0d..88c3d857386 100644
--- a/drivers/net/wireless/ath/ar9170/main.c
+++ b/drivers/net/wireless/ath/ar9170/main.c
@@ -1967,13 +1967,14 @@ static int ar9170_conf_tx(struct ieee80211_hw *hw, u16 queue,
 	int ret;
 
 	mutex_lock(&ar->mutex);
-	if ((param) && !(queue > __AR9170_NUM_TXQ)) {
+	if (queue < __AR9170_NUM_TXQ) {
 		memcpy(&ar->edcf[ar9170_qos_hwmap[queue]],
 		       param, sizeof(*param));
 
 		ret = ar9170_set_qos(ar);
-	} else
+	} else {
 		ret = -EINVAL;
+	}
 
 	mutex_unlock(&ar->mutex);
 	return ret;
-- 
GitLab


From 651b1f125c7e3806bbd635739d009433dc07372d Mon Sep 17 00:00:00 2001
From: Magnus Damm <damm@igel.co.jp>
Date: Mon, 10 Aug 2009 23:41:18 +0200
Subject: [PATCH 0754/1153] PM / Driver Core: Kill dev_pm_ops platform warning
 for now

Commit 783ea7d4eeefe895f2731fe73ac951e94418927b
(Driver Core: Rework platform suspend/resume, print warning)
added a warning message printed for platform drivers that use the
legacy PM callbacks rather than struct dev_pm_ops.  Unfortunately,
this resulted in some confusion and made some people try to convert
drivers by replacing the old callbacks with struct dev_pm_ops in
automatic way, which generally is not a good idea.

Remove the platform device runtime dev_pm_ops warning for now,
because it's annoying to users and it's not really necessary right
now.

[rjw: Modified the changelog to be more informative.]

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 drivers/base/platform.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/base/platform.c b/drivers/base/platform.c
index 81cb01bfc35..456594bd97b 100644
--- a/drivers/base/platform.c
+++ b/drivers/base/platform.c
@@ -483,9 +483,6 @@ int platform_driver_register(struct platform_driver *drv)
 		drv->driver.remove = platform_drv_remove;
 	if (drv->shutdown)
 		drv->driver.shutdown = platform_drv_shutdown;
-	if (drv->suspend || drv->resume)
-		pr_warning("Platform driver '%s' needs updating - please use "
-			"dev_pm_ops\n", drv->driver.name);
 
 	return driver_register(&drv->driver);
 }
-- 
GitLab


From 314dabb83a547ec4da819e8cbc78fac9cec605cd Mon Sep 17 00:00:00 2001
From: James Morris <jmorris@namei.org>
Date: Mon, 10 Aug 2009 22:00:13 +1000
Subject: [PATCH 0755/1153] SELinux: fix memory leakage in
 /security/selinux/hooks.c

Fix memory leakage in /security/selinux/hooks.c

The buffer always needs to be freed here; we either error
out or allocate more memory.

Reported-by: iceberg <strakh@ispras.ru>
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by:  Stephen Smalley <sds@tycho.nsa.gov>
---
 security/selinux/hooks.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/security/selinux/hooks.c b/security/selinux/hooks.c
index 15c2a08a66f..1e8cfc4c2ed 100644
--- a/security/selinux/hooks.c
+++ b/security/selinux/hooks.c
@@ -1285,6 +1285,8 @@ static int inode_doinit_with_dentry(struct inode *inode, struct dentry *opt_dent
 		rc = inode->i_op->getxattr(dentry, XATTR_NAME_SELINUX,
 					   context, len);
 		if (rc == -ERANGE) {
+			kfree(context);
+
 			/* Need a larger buffer.  Query for the right size. */
 			rc = inode->i_op->getxattr(dentry, XATTR_NAME_SELINUX,
 						   NULL, 0);
@@ -1292,7 +1294,6 @@ static int inode_doinit_with_dentry(struct inode *inode, struct dentry *opt_dent
 				dput(dentry);
 				goto out_unlock;
 			}
-			kfree(context);
 			len = rc;
 			context = kmalloc(len+1, GFP_NOFS);
 			if (!context) {
-- 
GitLab


From dd704698f56c1451fc9c5daadcd6e3a089de2c40 Mon Sep 17 00:00:00 2001
From: Takashi Iwai <tiwai@suse.de>
Date: Tue, 11 Aug 2009 08:45:11 +0200
Subject: [PATCH 0756/1153] ALSA: hda - Don't override ADC definitions for ALC
 codecs

ALC269 and ALC861-VD parsers override the ADC definitions
unconditionally without checking the spec definition.  This causes
the problem when any inconsistent ADC is set up in the device quirk
(like ALC272 with digital-mic).

This patch avoids the overriding by adding the proper checks.

Reference: Novell bnc#529467
	https://bugzilla.novell.com/show_bug.cgi?id=529467

Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/patch_realtek.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)

diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index 5cc927f4783..fea976793ae 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -15579,9 +15579,12 @@ static int patch_alc861vd(struct hda_codec *codec)
 	spec->stream_digital_playback = &alc861vd_pcm_digital_playback;
 	spec->stream_digital_capture = &alc861vd_pcm_digital_capture;
 
-	spec->adc_nids = alc861vd_adc_nids;
-	spec->num_adc_nids = ARRAY_SIZE(alc861vd_adc_nids);
-	spec->capsrc_nids = alc861vd_capsrc_nids;
+	if (!spec->adc_nids) {
+		spec->adc_nids = alc861vd_adc_nids;
+		spec->num_adc_nids = ARRAY_SIZE(alc861vd_adc_nids);
+	}
+	if (!spec->capsrc_nids)
+		spec->capsrc_nids = alc861vd_capsrc_nids;
 
 	set_capture_mixer(spec);
 	set_beep_amp(spec, 0x0b, 0x05, HDA_INPUT);
@@ -17498,9 +17501,12 @@ static int patch_alc662(struct hda_codec *codec)
 	spec->stream_digital_playback = &alc662_pcm_digital_playback;
 	spec->stream_digital_capture = &alc662_pcm_digital_capture;
 
-	spec->adc_nids = alc662_adc_nids;
-	spec->num_adc_nids = ARRAY_SIZE(alc662_adc_nids);
-	spec->capsrc_nids = alc662_capsrc_nids;
+	if (!spec->adc_nids) {
+		spec->adc_nids = alc662_adc_nids;
+		spec->num_adc_nids = ARRAY_SIZE(alc662_adc_nids);
+	}
+	if (!spec->capsrc_nids)
+		spec->capsrc_nids = alc662_capsrc_nids;
 
 	if (!spec->cap_mixer)
 		set_capture_mixer(spec);
-- 
GitLab


From 0d01f31439c1e4d602bf9fdc924ab66f407f5e38 Mon Sep 17 00:00:00 2001
From: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Date: Sun, 9 Aug 2009 21:44:49 -0700
Subject: [PATCH 0757/1153] x86, mce: therm_throt - change when we print
 messages

My Latitude d630 seems to be handling thermal events in SMI by
lowering the max frequency of the CPU till it cools down but
still leaks the "everything is normal" events.

This spams the console and with high priority printks.

Adjust therm_throt driver to only print messages about the fact
that temperatire returned back to normal when leaving the
throttling state.

Also lower the severity of "back to normal" message from
KERN_CRIT to KERN_INFO.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <20090810051513.0558F526EC9@mailhub.coreip.homeip.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/cpu/mcheck/therm_throt.c | 18 +++++++++++-------
 1 file changed, 11 insertions(+), 7 deletions(-)

diff --git a/arch/x86/kernel/cpu/mcheck/therm_throt.c b/arch/x86/kernel/cpu/mcheck/therm_throt.c
index bff8dd191dd..8bc64cfbe93 100644
--- a/arch/x86/kernel/cpu/mcheck/therm_throt.c
+++ b/arch/x86/kernel/cpu/mcheck/therm_throt.c
@@ -36,6 +36,7 @@
 
 static DEFINE_PER_CPU(__u64, next_check) = INITIAL_JIFFIES;
 static DEFINE_PER_CPU(unsigned long, thermal_throttle_count);
+static DEFINE_PER_CPU(bool, thermal_throttle_active);
 
 static atomic_t therm_throt_en		= ATOMIC_INIT(0);
 
@@ -96,24 +97,27 @@ static int therm_throt_process(int curr)
 {
 	unsigned int cpu = smp_processor_id();
 	__u64 tmp_jiffs = get_jiffies_64();
+	bool was_throttled = __get_cpu_var(thermal_throttle_active);
+	bool is_throttled = __get_cpu_var(thermal_throttle_active) = curr;
 
-	if (curr)
+	if (is_throttled)
 		__get_cpu_var(thermal_throttle_count)++;
 
-	if (time_before64(tmp_jiffs, __get_cpu_var(next_check)))
+	if (!(was_throttled ^ is_throttled) &&
+	    time_before64(tmp_jiffs, __get_cpu_var(next_check)))
 		return 0;
 
 	__get_cpu_var(next_check) = tmp_jiffs + CHECK_INTERVAL;
 
 	/* if we just entered the thermal event */
-	if (curr) {
+	if (is_throttled) {
 		printk(KERN_CRIT "CPU%d: Temperature above threshold, "
-		       "cpu clock throttled (total events = %lu)\n", cpu,
-		       __get_cpu_var(thermal_throttle_count));
+		       "cpu clock throttled (total events = %lu)\n",
+		       cpu, __get_cpu_var(thermal_throttle_count));
 
 		add_taint(TAINT_MACHINE_CHECK);
-	} else {
-		printk(KERN_CRIT "CPU%d: Temperature/speed normal\n", cpu);
+	} else if (was_throttled) {
+		printk(KERN_INFO "CPU%d: Temperature/speed normal\n", cpu);
 	}
 
 	return 1;
-- 
GitLab


From 3c581a7f94542341bf0da496a226b44ac63521a8 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Tue, 11 Aug 2009 10:47:36 +0200
Subject: [PATCH 0758/1153] perf_counter, x86: Fix lapic printk message

Instead of this garbled bootup on UP Pentium-M systems:

[    0.015048] Performance Counters:
[    0.016004] no Local APIC, try rebooting with lapicno PMU driver, software counters only.

Print:

[    0.015050] Performance Counters:
[    0.016004] no APIC, boot with the "lapic" boot parameter to force-enable it.
[    0.017003] no PMU driver, software counters only.

Cf: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/cpu/perf_counter.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c
index a7aa8f90095..40e233a24d9 100644
--- a/arch/x86/kernel/cpu/perf_counter.c
+++ b/arch/x86/kernel/cpu/perf_counter.c
@@ -1590,7 +1590,7 @@ static int p6_pmu_init(void)
 	}
 
 	if (!cpu_has_apic) {
-		pr_info("no Local APIC, try rebooting with lapic");
+		pr_info("no APIC, boot with the \"lapic\" boot parameter to force-enable it.\n");
 		return -ENODEV;
 	}
 
-- 
GitLab


From f64ccccb8afa43abdd63fcbd230f818d6ea0883f Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Tue, 11 Aug 2009 10:26:33 +0200
Subject: [PATCH 0759/1153] perf_counter, x86: Fix generic cache events on
 P6-mobile CPUs

Johannes Stezenbach reported that 'perf stat' does not count
cache-miss and cache-references events on his Pentium-M based
laptop.

This is because we left them blank in p6_perfmon_event_map[],
fill them in.

Reported-by: Johannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/cpu/perf_counter.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c
index 40e233a24d9..fffc126dbdf 100644
--- a/arch/x86/kernel/cpu/perf_counter.c
+++ b/arch/x86/kernel/cpu/perf_counter.c
@@ -72,8 +72,8 @@ static const u64 p6_perfmon_event_map[] =
 {
   [PERF_COUNT_HW_CPU_CYCLES]		= 0x0079,
   [PERF_COUNT_HW_INSTRUCTIONS]		= 0x00c0,
-  [PERF_COUNT_HW_CACHE_REFERENCES]	= 0x0000,
-  [PERF_COUNT_HW_CACHE_MISSES]		= 0x0000,
+  [PERF_COUNT_HW_CACHE_REFERENCES]	= 0x0f2e,
+  [PERF_COUNT_HW_CACHE_MISSES]		= 0x012e,
   [PERF_COUNT_HW_BRANCH_INSTRUCTIONS]	= 0x00c4,
   [PERF_COUNT_HW_BRANCH_MISSES]		= 0x00c5,
   [PERF_COUNT_HW_BUS_CYCLES]		= 0x0062,
-- 
GitLab


From fbd8b1819e80ac5a176d085fdddc3a34d1499318 Mon Sep 17 00:00:00 2001
From: Kevin Winchester <kjwinchester@gmail.com>
Date: Mon, 10 Aug 2009 19:56:45 -0300
Subject: [PATCH 0760/1153] x86: Clear incorrectly forced X86_FEATURE_LAHF_LM
 flag

Due to an erratum with certain AMD Athlon 64 processors, the
BIOS may need to force enable the LAHF_LM capability.
Unfortunately, in at least one case, the BIOS does this even
for processors that do not support the functionality.

Add a specific check that will clear the feature bit for
processors known not to support the LAHF/SAHF instructions.

Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
LKML-Reference: <4A80A5AD.2000209@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/cpu/amd.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/x86/kernel/cpu/amd.c b/arch/x86/kernel/cpu/amd.c
index e2485b03f1c..63fddcd082c 100644
--- a/arch/x86/kernel/cpu/amd.c
+++ b/arch/x86/kernel/cpu/amd.c
@@ -400,6 +400,13 @@ static void __cpuinit init_amd(struct cpuinfo_x86 *c)
 		level = cpuid_eax(1);
 		if((level >= 0x0f48 && level < 0x0f50) || level >= 0x0f58)
 			set_cpu_cap(c, X86_FEATURE_REP_GOOD);
+
+		/*
+		 * Some BIOSes incorrectly force this feature, but only K8
+		 * revision D (model = 0x14) and later actually support it.
+		 */
+		if (c->x86_model < 0x14)
+			clear_cpu_cap(c, X86_FEATURE_LAHF_LM);
 	}
 	if (c->x86 == 0x10 || c->x86 == 0x11)
 		set_cpu_cap(c, X86_FEATURE_REP_GOOD);
-- 
GitLab


From dee2b904a1f93c275a015b67cd693038d74b18e8 Mon Sep 17 00:00:00 2001
From: Mikael Pettersson <mikpe@it.uu.se>
Date: Sun, 9 Aug 2009 21:21:57 +0200
Subject: [PATCH 0761/1153] IXP4xx: Fix IO_SPACE_LIMIT for 2.6.31-rc core PCI
 changes
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

2.6.31-rc kernels don't boot on my ixp4xx box (ds101), because the libata
driver doesn't find the PCI IDE controller any more. 2.6.30 was fine.
I traced this to a PCI update (1f82de10d6b1d845155363c895c552e61b36b51a)
in 2.6.30-git19. Diffing the kernel boot logs from 2.6.30-git18 and
2.6.30-git19 illustrates the breakage:

> --- dmesg-2.6.30-git18	2009-08-04 01:45:22.000000000 +0200
> +++ dmesg-2.6.30-git19	2009-08-04 01:45:46.000000000 +0200
> @@ -26,6 +26,13 @@
>  pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot
>  pci 0000:00:02.2: PME# disabled
>  PCI: bus0: Fast back to back transfers disabled
> +pci 0000:00:01.0: BAR 0: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 1: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 2: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 3: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.1: BAR 4: can't allocate I/O resource [0x10000-0xffff]
>  bio: create slab <bio-0> at 0
>  SCSI subsystem initialized
>  NET: Registered protocol family 2
> @@ -44,11 +51,7 @@
>  console [ttyS0] enabled
>  serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
>  Driver 'sd' needs updating - please use bus_type methods
> -PCI: enabling device 0000:00:01.0 (0140 -> 0141)
> -scsi0 : pata_artop
> -scsi1 : pata_artop
> -ata1: PATA max UDMA/100 cmd 0x1050 ctl 0x1060 bmdma 0x1040 irq 28
> -ata2: PATA max UDMA/100 cmd 0x1058 ctl 0x1064 bmdma 0x1048 irq 28
> +pata_artop 0000:00:01.0: no available native port
>  Using configured DiskOnChip probe address 0x50000000
>  DiskOnChip found at 0x50000000
>  NAND device: Manufacturer ID: 0x98, Chip ID: 0x73 (Toshiba NAND 16MiB 3,3V 8-bit)

The specific change in 1f82de10d6b1d845155363c895c552e61b36b51a responsible
for this failure turned out to be the following:

> --- a/drivers/pci/probe.c
> +++ b/drivers/pci/probe.c
> @@ -193,7 +193,7 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type,
>  		res->flags |= pci_calc_resource_flags(l) | IORESOURCE_SIZEALIGN;
>  		if (type == pci_bar_io) {
>  			l &= PCI_BASE_ADDRESS_IO_MASK;
> -			mask = PCI_BASE_ADDRESS_IO_MASK & 0xffff;
> +			mask = PCI_BASE_ADDRESS_IO_MASK & IO_SPACE_LIMIT;
>  		} else {
>  			l &= PCI_BASE_ADDRESS_MEM_MASK;
>  			mask = (u32)PCI_BASE_ADDRESS_MEM_MASK;

Every arch except arm's ixp4xx defines IO_SPACE_LIMIT as an all-bits-one
bitmask, typically -1UL but sometimes only a 16-bit 0x0000ffff. But ixp4xx
defines it as 0xffff0000, which is now causing the PCI failures.

Russell King noted that ixp4xx has 64KB PCI IO space, so IO_SPACE_LIMIT
should be 0x0000ffff. This patch makes that change, which fixes the PCI
failures on my ixp4xx box.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
---
 arch/arm/mach-ixp4xx/include/mach/io.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h
index ce63048d45e..8a947d42a6f 100644
--- a/arch/arm/mach-ixp4xx/include/mach/io.h
+++ b/arch/arm/mach-ixp4xx/include/mach/io.h
@@ -17,7 +17,7 @@
 
 #include <mach/hardware.h>
 
-#define IO_SPACE_LIMIT 0xffff0000
+#define IO_SPACE_LIMIT 0x0000ffff
 
 extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
 extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data);
-- 
GitLab


From 51b89f7a6615eca184aa0b85db5781d931e9c8d1 Mon Sep 17 00:00:00 2001
From: Fenghua Yu <[fenghua.yu@intel.com]>
Date: Tue, 11 Aug 2009 14:52:10 -0700
Subject: [PATCH 0762/1153] Bug Fix arch/ia64/kernel/pci-dma.c: fix recursive
 dma_supported() call in iommu_dma_supported()

In commit 160c1d8e40866edfeae7d68816b7005d70acf391,
dma_ops->dma_supported = iommu_dma_supported;

This dma_ops->dma_supported is first called in platform_dma_init() during kernel
boot. Then dma_ops->dma_supported will be called recursively in
iommu_dma_supported.

Kernel can not boot because kernel can not get out of iommu_dma_supported until
it runs out of stack memory.

Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
---
 arch/ia64/kernel/pci-dma.c | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/arch/ia64/kernel/pci-dma.c b/arch/ia64/kernel/pci-dma.c
index 05695962fe4..f6b1ff0aea7 100644
--- a/arch/ia64/kernel/pci-dma.c
+++ b/arch/ia64/kernel/pci-dma.c
@@ -69,11 +69,6 @@ iommu_dma_init(void)
 
 int iommu_dma_supported(struct device *dev, u64 mask)
 {
-	struct dma_map_ops *ops = platform_dma_get_ops(dev);
-
-	if (ops->dma_supported)
-		return ops->dma_supported(dev, mask);
-
 	/* Copied from i386. Doesn't make much sense, because it will
 	   only work for pci_alloc_coherent.
 	   The caller just has to use GFP_DMA in this case. */
-- 
GitLab


From 8d6f9af91959256244878cd801c1c969e66cd093 Mon Sep 17 00:00:00 2001
From: Johannes Weiner <[hannes@cmpxchg.org]>
Date: Tue, 11 Aug 2009 14:52:10 -0700
Subject: [PATCH 0763/1153] ia64: boolean __test_and_clear_bit

__test_and_clear_bit() returns a bitfield with the tested-for bit set.
Make it consistent with the other bitops - of ia64 but also every
other architecture - and return a boolean value.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
---
 arch/ia64/include/asm/bitops.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/ia64/include/asm/bitops.h b/arch/ia64/include/asm/bitops.h
index e2ca8003733..57a2787bc9f 100644
--- a/arch/ia64/include/asm/bitops.h
+++ b/arch/ia64/include/asm/bitops.h
@@ -286,7 +286,7 @@ __test_and_clear_bit(int nr, volatile void * addr)
 {
 	__u32 *p = (__u32 *) addr + (nr >> 5);
 	__u32 m = 1 << (nr & 31);
-	int oldbitset = *p & m;
+	int oldbitset = (*p & m) != 0;
 
 	*p &= ~m;
 	return oldbitset;
-- 
GitLab


From cfa5f809e399c699974ba6018eefa022bbc2e16e Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <[jaswinder@kernel.org]>
Date: Tue, 11 Aug 2009 14:52:10 -0700
Subject: [PATCH 0764/1153] IA64: includecheck fix: ia64, ia64_ksyms.c

fix the following 'make includecheck' warning:

  arch/ia64/kernel/ia64_ksyms.c: asm/page.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
---
 arch/ia64/kernel/ia64_ksyms.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/arch/ia64/kernel/ia64_ksyms.c b/arch/ia64/kernel/ia64_ksyms.c
index 2d311864e35..8ebccb589e1 100644
--- a/arch/ia64/kernel/ia64_ksyms.c
+++ b/arch/ia64/kernel/ia64_ksyms.c
@@ -21,6 +21,7 @@ EXPORT_SYMBOL(csum_ipv6_magic);
 
 #include <asm/page.h>
 EXPORT_SYMBOL(clear_page);
+EXPORT_SYMBOL(copy_page);
 
 #ifdef CONFIG_VIRTUAL_MEM_MAP
 #include <linux/bootmem.h>
@@ -60,9 +61,6 @@ EXPORT_SYMBOL(__udivdi3);
 EXPORT_SYMBOL(__moddi3);
 EXPORT_SYMBOL(__umoddi3);
 
-#include <asm/page.h>
-EXPORT_SYMBOL(copy_page);
-
 #if defined(CONFIG_MD_RAID456) || defined(CONFIG_MD_RAID456_MODULE)
 extern void xor_ia64_2(void);
 extern void xor_ia64_3(void);
-- 
GitLab


From b5a8879347bbe68bd24c8870503bf6a0362da26b Mon Sep 17 00:00:00 2001
From: Jaswinder Singh Rajput <[jaswinder@kernel.org]>
Date: Tue, 11 Aug 2009 14:52:11 -0700
Subject: [PATCH 0765/1153] IA64: includecheck fix: ia64, pgtable.h

fix the following 'make includecheck' warning:

  arch/ia64/include/asm/pgtable.h: asm/processor.h is included more than once.

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
---
 arch/ia64/include/asm/pgtable.h | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/ia64/include/asm/pgtable.h b/arch/ia64/include/asm/pgtable.h
index 0a9cc73d35c..8840a690d1e 100644
--- a/arch/ia64/include/asm/pgtable.h
+++ b/arch/ia64/include/asm/pgtable.h
@@ -155,7 +155,6 @@
 #include <linux/bitops.h>
 #include <asm/cacheflush.h>
 #include <asm/mmu_context.h>
-#include <asm/processor.h>
 
 /*
  * Next come the mappings that determine how mmap() protection bits
-- 
GitLab


From bf2a4c7270b9a22243a91ab5efcc47aaf997c66b Mon Sep 17 00:00:00 2001
From: Fenghua Yu <[fenghua.yu@intel.com]>
Date: Tue, 11 Aug 2009 14:52:11 -0700
Subject: [PATCH 0766/1153] arch/ia64/Makefile: Remove -mtune=merced in IA64
 kernel build

Between GCC version 3.4.0 and 4.3.3 (including 3.4.0 and 4.3.3), -mtune=merced
is implemented in GCC. Starting from 4.4.0, -mtune=merced is deprecated.

Even implemented in versions between 3.4.0 and 4.3.3, the -mtune=merced
feature has been broken in some of the versions. For example, GCC 4.1.2 reports
interanl tuning function errors during kernel building with -mtune=merced. Or
GCC Bugzilla 16130 reports another -mtune=merced issue on GCC 3.4.1.

So I would remove the -mtune=merced from IA64 kernel build. Without this option,
kernel on Merced will remain the same except losing an unstable and out-of-date
performance tunning feature.

Since GCC version 3.4.0, -mtune=mckinley has been implemented. The
-mtune=mckinley option functions the same as mtune=itanium2. And mtune=itanium2
is the default option. So we don't need to add mtune=mckinley either since its
been the default option in any GCC version which implements this option.

Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
---
 arch/ia64/Makefile | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/arch/ia64/Makefile b/arch/ia64/Makefile
index 58a7e46affd..e7cbaa02cd0 100644
--- a/arch/ia64/Makefile
+++ b/arch/ia64/Makefile
@@ -41,11 +41,6 @@ $(error Sorry, you need a newer version of the assember, one that is built from
 		ftp://ftp.hpl.hp.com/pub/linux-ia64/gas-030124.tar.gz)
 endif
 
-ifeq ($(call cc-version),0304)
-	cflags-$(CONFIG_ITANIUM)	+= -mtune=merced
-	cflags-$(CONFIG_MCKINLEY)	+= -mtune=mckinley
-endif
-
 KBUILD_CFLAGS += $(cflags-y)
 head-y := arch/ia64/kernel/head.o arch/ia64/kernel/init_task.o
 
-- 
GitLab


From 5359dffd4396f281c5b77de1acbee6fb1b333b23 Mon Sep 17 00:00:00 2001
From: Fenghua Yu <fenghua.yu@intel.com>
Date: Tue, 11 Aug 2009 14:52:11 -0700
Subject: [PATCH 0767/1153] ia64/topology.c: exit cache_add_dev when
 kobject_init_and_add fails

Make cache_add_dev exit sysfs when kobject_init_and_add returns an error.

Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
---
 arch/ia64/kernel/topology.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/arch/ia64/kernel/topology.c b/arch/ia64/kernel/topology.c
index bc80dff1df7..8f060352e12 100644
--- a/arch/ia64/kernel/topology.c
+++ b/arch/ia64/kernel/topology.c
@@ -372,6 +372,10 @@ static int __cpuinit cache_add_dev(struct sys_device * sys_dev)
 	retval = kobject_init_and_add(&all_cpu_cache_info[cpu].kobj,
 				      &cache_ktype_percpu_entry, &sys_dev->kobj,
 				      "%s", "cache");
+	if (unlikely(retval < 0)) {
+		cpu_cache_sysfs_exit(cpu);
+		return retval;
+	}
 
 	for (i = 0; i < all_cpu_cache_info[cpu].num_cache_leaves; i++) {
 		this_object = LEAF_KOBJECT_PTR(cpu,i);
@@ -385,7 +389,7 @@ static int __cpuinit cache_add_dev(struct sys_device * sys_dev)
 			}
 			kobject_put(&all_cpu_cache_info[cpu].kobj);
 			cpu_cache_sysfs_exit(cpu);
-			break;
+			return retval;
 		}
 		kobject_uevent(&(this_object->kobj), KOBJ_ADD);
 	}
-- 
GitLab


From e7369e01eb85550ed60dd1b0e120b69dfb03dc23 Mon Sep 17 00:00:00 2001
From: Roel Kluin <[roel.kluin@gmail.com]>
Date: Tue, 11 Aug 2009 14:52:11 -0700
Subject: [PATCH 0768/1153] arch/ia64/kernel/iosapic: missing test after
 ioremap()

Missing test after ioremap()

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
---
 arch/ia64/kernel/iosapic.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/ia64/kernel/iosapic.c b/arch/ia64/kernel/iosapic.c
index c48b03f2b61..dab4d393908 100644
--- a/arch/ia64/kernel/iosapic.c
+++ b/arch/ia64/kernel/iosapic.c
@@ -1072,6 +1072,10 @@ iosapic_init (unsigned long phys_addr, unsigned int gsi_base)
 	}
 
 	addr = ioremap(phys_addr, 0);
+	if (addr == NULL) {
+		spin_unlock_irqrestore(&iosapic_lock, flags);
+		return -ENOMEM;
+	}
 	ver = iosapic_version(addr);
 	if ((err = iosapic_check_gsi_range(gsi_base, ver))) {
 		iounmap(addr);
-- 
GitLab


From 0cc6eee130b0c062feec8446d9cecdb17d2cfad3 Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@infradead.org>
Date: Sat, 18 Jul 2009 18:14:53 -0400
Subject: [PATCH 0769/1153] xfs: avoid memory allocation under m_peraglock in
 growfs code

Allocate the memory for the larger m_perag array before taking the
per-AG lock as the per-AG lock can be taken under the i_lock which
can be taken from reclaim context.

Reported by the new reclaim context tracing in lockdep.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_fsops.c | 20 ++++++++++++++------
 1 file changed, 14 insertions(+), 6 deletions(-)

diff --git a/fs/xfs/xfs_fsops.c b/fs/xfs/xfs_fsops.c
index cbd451bb484..2d0b3e1da9e 100644
--- a/fs/xfs/xfs_fsops.c
+++ b/fs/xfs/xfs_fsops.c
@@ -167,17 +167,25 @@ xfs_growfs_data_private(
 	new = nb - mp->m_sb.sb_dblocks;
 	oagcount = mp->m_sb.sb_agcount;
 	if (nagcount > oagcount) {
+		void *new_perag, *old_perag;
+
 		xfs_filestream_flush(mp);
+
+		new_perag = kmem_zalloc(sizeof(xfs_perag_t) * nagcount,
+					KM_MAYFAIL);
+		if (!new_perag)
+			return XFS_ERROR(ENOMEM);
+
 		down_write(&mp->m_peraglock);
-		mp->m_perag = kmem_realloc(mp->m_perag,
-			sizeof(xfs_perag_t) * nagcount,
-			sizeof(xfs_perag_t) * oagcount,
-			KM_SLEEP);
-		memset(&mp->m_perag[oagcount], 0,
-			(nagcount - oagcount) * sizeof(xfs_perag_t));
+		memcpy(new_perag, mp->m_perag, sizeof(xfs_perag_t) * oagcount);
+		old_perag = mp->m_perag;
+		mp->m_perag = new_perag;
+
 		mp->m_flags |= XFS_MOUNT_32BITINODES;
 		nagimax = xfs_initialize_perag(mp, nagcount);
 		up_write(&mp->m_peraglock);
+
+		kmem_free(old_perag);
 	}
 	tp = xfs_trans_alloc(mp, XFS_TRANS_GROWFS);
 	tp->t_flags |= XFS_TRANS_RESERVE;
-- 
GitLab


From ca35dcd6cae7d4a780c484c53f45548c4719f82c Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@infradead.org>
Date: Sat, 18 Jul 2009 18:14:54 -0400
Subject: [PATCH 0770/1153] xfs: switch to NOFS allocation under i_lock in
 xfs_getbmap

xfs_getbmap allocates memory with i_lock held, but i_lock is taken in
reclaim context so all allocations under it must avoid recursions into
the filesystem.

Reported by the new reclaim context tracing in lockdep.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_bmap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/xfs/xfs_bmap.c b/fs/xfs/xfs_bmap.c
index 7928b9983c1..8ee5b5a76a2 100644
--- a/fs/xfs/xfs_bmap.c
+++ b/fs/xfs/xfs_bmap.c
@@ -6009,7 +6009,7 @@ xfs_getbmap(
 	 */
 	error = ENOMEM;
 	subnex = 16;
-	map = kmem_alloc(subnex * sizeof(*map), KM_MAYFAIL);
+	map = kmem_alloc(subnex * sizeof(*map), KM_MAYFAIL | KM_NOFS);
 	if (!map)
 		goto out_unlock_ilock;
 
-- 
GitLab


From f41d7fb9da05b604f8a69fb6cac2a0563c8ede4e Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@infradead.org>
Date: Sat, 18 Jul 2009 18:14:55 -0400
Subject: [PATCH 0771/1153] xfs: switch to NOFS allocation under i_lock in
 xfs_da_state_alloc

xfs_da_state_alloc is always called with i_lock held, but i_lock is taken in
reclaim context so all allocations under it must avoid recursions into the
filesystem.

Reported by the new reclaim context tracing in lockdep.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_da_btree.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/xfs/xfs_da_btree.c b/fs/xfs/xfs_da_btree.c
index 9ff6e57a507..bd0bb6dfcdf 100644
--- a/fs/xfs/xfs_da_btree.c
+++ b/fs/xfs/xfs_da_btree.c
@@ -2201,7 +2201,7 @@ kmem_zone_t *xfs_dabuf_zone;		/* dabuf zone */
 xfs_da_state_t *
 xfs_da_state_alloc(void)
 {
-	return kmem_zone_zalloc(xfs_da_state_zone, KM_SLEEP);
+	return kmem_zone_zalloc(xfs_da_state_zone, KM_NOFS);
 }
 
 /*
-- 
GitLab


From 73195ed7864ae4a1fb0bea2ed9df59d19b4fde90 Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@infradead.org>
Date: Sat, 18 Jul 2009 18:14:56 -0400
Subject: [PATCH 0772/1153] xfs: switch to NOFS allocation under i_lock in
 xfs_da_buf_make

i_lock is taken in the reclaim context so all allocations under it
must avoid recursions into the filesystem.

Reported by the new reclaim context tracing in lockdep.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_da_btree.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/fs/xfs/xfs_da_btree.c b/fs/xfs/xfs_da_btree.c
index bd0bb6dfcdf..2847bbc1c53 100644
--- a/fs/xfs/xfs_da_btree.c
+++ b/fs/xfs/xfs_da_btree.c
@@ -2261,9 +2261,9 @@ xfs_da_buf_make(int nbuf, xfs_buf_t **bps, inst_t *ra)
 	int		off;
 
 	if (nbuf == 1)
-		dabuf = kmem_zone_alloc(xfs_dabuf_zone, KM_SLEEP);
+		dabuf = kmem_zone_alloc(xfs_dabuf_zone, KM_NOFS);
 	else
-		dabuf = kmem_alloc(XFS_DA_BUF_SIZE(nbuf), KM_SLEEP);
+		dabuf = kmem_alloc(XFS_DA_BUF_SIZE(nbuf), KM_NOFS);
 	dabuf->dirty = 0;
 #ifdef XFS_DABUF_DEBUG
 	dabuf->ra = ra;
-- 
GitLab


From 3f52c2f0a07c23771909cc53f2e9451a7f1bf253 Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@infradead.org>
Date: Sat, 18 Jul 2009 18:14:57 -0400
Subject: [PATCH 0773/1153] xfs: switch to NOFS allocation under i_lock in
 xfs_dir_cilookup_result

xfs_dir_cilookup_result is always called with i_lock held, but i_lock is taken
in reclaim context so all allocations under it must avoid recursions into the
filesystem.

Reported by the new reclaim context tracing in lockdep.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_dir2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/xfs/xfs_dir2.c b/fs/xfs/xfs_dir2.c
index c657bec6d95..bb1d58eb398 100644
--- a/fs/xfs/xfs_dir2.c
+++ b/fs/xfs/xfs_dir2.c
@@ -256,7 +256,7 @@ xfs_dir_cilookup_result(
 					!(args->op_flags & XFS_DA_OP_CILOOKUP))
 		return EEXIST;
 
-	args->value = kmem_alloc(len, KM_MAYFAIL);
+	args->value = kmem_alloc(len, KM_NOFS | KM_MAYFAIL);
 	if (!args->value)
 		return ENOMEM;
 
-- 
GitLab


From 36fae17a648e0aee5d9560514d08477ef48dc87f Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@infradead.org>
Date: Sat, 18 Jul 2009 18:14:58 -0400
Subject: [PATCH 0774/1153] xfs: switch to NOFS allocation under i_lock in
 xfs_buf_associate_memory

xfs_buf_associate_memory is used for setting up the spare buffer for the
log wrap case in xlog_sync which can happen under i_lock when called from
xfs_fsync. The i_lock mutex is taken in reclaim context so all allocations
under it must avoid recursions into the filesystem.  There are a couple
more uses of xfs_buf_associate_memory in the log recovery code that are
also affected by this, but I'd rather keep the code simple than passing on
a gfp_mask argument.  Longer term we should just stop requiring the memoery
allocation in xlog_sync by some smaller rework of the buffer layer.

Reported by the new reclaim context tracing in lockdep.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/linux-2.6/xfs_buf.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/xfs/linux-2.6/xfs_buf.c b/fs/xfs/linux-2.6/xfs_buf.c
index 1418b916fc2..178c20c13e8 100644
--- a/fs/xfs/linux-2.6/xfs_buf.c
+++ b/fs/xfs/linux-2.6/xfs_buf.c
@@ -770,7 +770,7 @@ xfs_buf_associate_memory(
 	bp->b_pages = NULL;
 	bp->b_addr = mem;
 
-	rval = _xfs_buf_get_pages(bp, page_count, 0);
+	rval = _xfs_buf_get_pages(bp, page_count, XBF_DONT_BLOCK);
 	if (rval)
 		return rval;
 
-- 
GitLab


From 10746e47e722b5688fcd6eba9fbf9b2e64a248a7 Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@infradead.org>
Date: Sat, 18 Jul 2009 18:14:59 -0400
Subject: [PATCH 0775/1153] xfs: switch to NOFS allocation under i_lock in
 xfs_attr_rmtval_set

xfs_attr_rmtval_set is always called with i_lock held, and i_lock is taken
in reclaim context so all allocations under it must avoid recursions into
the filesystem.

Reported by the new reclaim context tracing in lockdep.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_attr.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/fs/xfs/xfs_attr.c b/fs/xfs/xfs_attr.c
index db15feb906f..bfb583791fe 100644
--- a/fs/xfs/xfs_attr.c
+++ b/fs/xfs/xfs_attr.c
@@ -2141,8 +2141,8 @@ xfs_attr_rmtval_set(xfs_da_args_t *args)
 		dblkno = XFS_FSB_TO_DADDR(mp, map.br_startblock),
 		blkcnt = XFS_FSB_TO_BB(mp, map.br_blockcount);
 
-		bp = xfs_buf_get_flags(mp->m_ddev_targp, dblkno,
-							blkcnt, XFS_BUF_LOCK);
+		bp = xfs_buf_get_flags(mp->m_ddev_targp, dblkno, blkcnt,
+				       XFS_BUF_LOCK | XBF_DONT_BLOCK);
 		ASSERT(bp);
 		ASSERT(!XFS_BUF_GETERROR(bp));
 
-- 
GitLab


From 7b02ecb3031b192823bc732ae717febc0a59aa92 Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@infradead.org>
Date: Sat, 18 Jul 2009 18:15:00 -0400
Subject: [PATCH 0776/1153] xfs: switch to NOFS allocation under i_lock in
 xfs_readlink_bmap

xfs_readlink_bmap is called with i_lock held, but i_lock is taken in
reclaim context so all allocations under it must avoid recursions into
the filesystem.

Reported by the new reclaim context tracing in lockdep.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_vnodeops.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/fs/xfs/xfs_vnodeops.c b/fs/xfs/xfs_vnodeops.c
index c4eca5ed5da..492d75bae2b 100644
--- a/fs/xfs/xfs_vnodeops.c
+++ b/fs/xfs/xfs_vnodeops.c
@@ -538,7 +538,9 @@ xfs_readlink_bmap(
 		d = XFS_FSB_TO_DADDR(mp, mval[n].br_startblock);
 		byte_cnt = XFS_FSB_TO_B(mp, mval[n].br_blockcount);
 
-		bp = xfs_buf_read(mp->m_ddev_targp, d, BTOBB(byte_cnt), 0);
+		bp = xfs_buf_read_flags(mp->m_ddev_targp, d, BTOBB(byte_cnt),
+					XBF_LOCK | XBF_MAPPED |
+					XBF_DONT_BLOCK);
 		error = XFS_BUF_GETERROR(bp);
 		if (error) {
 			xfs_ioerror_alert("xfs_readlink",
-- 
GitLab


From ddd3a14e0f030f0f7b900621f67532285b8657ef Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@infradead.org>
Date: Sat, 18 Jul 2009 18:15:01 -0400
Subject: [PATCH 0777/1153] xfs: switch to NOFS allocation under i_lock in
 xfs_attr_rmtval_get

xfs_attr_rmtval_get is always called with i_lock held, but i_lock is taken
in reclaim context so all allocations under it must avoid recursions into
the filesystem.

Reported by the new reclaim context tracing in lockdep.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_attr.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/fs/xfs/xfs_attr.c b/fs/xfs/xfs_attr.c
index bfb583791fe..4ece1906bd4 100644
--- a/fs/xfs/xfs_attr.c
+++ b/fs/xfs/xfs_attr.c
@@ -2010,7 +2010,9 @@ xfs_attr_rmtval_get(xfs_da_args_t *args)
 			dblkno = XFS_FSB_TO_DADDR(mp, map[i].br_startblock);
 			blkcnt = XFS_FSB_TO_BB(mp, map[i].br_blockcount);
 			error = xfs_read_buf(mp, mp->m_ddev_targp, dblkno,
-					     blkcnt, XFS_BUF_LOCK, &bp);
+					     blkcnt,
+					     XFS_BUF_LOCK | XBF_DONT_BLOCK,
+					     &bp);
 			if (error)
 				return(error);
 
-- 
GitLab


From e0c222c411e22f086e929cd69fdcc89336164ec1 Mon Sep 17 00:00:00 2001
From: Eric Sandeen <sandeen@sandeen.net>
Date: Mon, 20 Jul 2009 10:52:15 -0500
Subject: [PATCH 0778/1153] use XFS_CORRUPTION_ERROR in xfs_btree_check_sblock

In Red Hat Bug 512552
 - Can't write to XFS mount during raid5 resync

a user ran into corruption while resyncing a raid, and we failed
a consistency test, but didn't get much more info; it'd be nice
to call XFS_CORRUPTION_ERROR here so we can see the buffer
contents.

Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_btree.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/fs/xfs/xfs_btree.c b/fs/xfs/xfs_btree.c
index e9df9957482..26717388acf 100644
--- a/fs/xfs/xfs_btree.c
+++ b/fs/xfs/xfs_btree.c
@@ -120,8 +120,8 @@ xfs_btree_check_sblock(
 			XFS_RANDOM_BTREE_CHECK_SBLOCK))) {
 		if (bp)
 			xfs_buftrace("SBTREE ERROR", bp);
-		XFS_ERROR_REPORT("xfs_btree_check_sblock", XFS_ERRLEVEL_LOW,
-				 cur->bc_mp);
+		XFS_CORRUPTION_ERROR("xfs_btree_check_sblock",
+			XFS_ERRLEVEL_LOW, cur->bc_mp, block);
 		return XFS_ERROR(EFSCORRUPTED);
 	}
 	return 0;
-- 
GitLab


From b89d4208de3de442c9025919c4261be0b38e79a4 Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@lst.de>
Date: Mon, 10 Aug 2009 11:32:18 -0300
Subject: [PATCH 0779/1153] xfs: check for dinode realtime flag corruption

Ramon tested XFS with a modified version of fsfuzzer and hit a NULL
pointer dereference in __xfs_get_blocks due to the RT device target
pointer being NULL.

To fix this reject inode with the realtime bit set on a a filesystem
without an RT subvolume during inode read.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Reported-by: Ramon de Carvalho Valle <ramon@risesecurity.org>
Tested-by: Ramon de Carvalho Valle <ramon@risesecurity.org>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_inode.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/fs/xfs/xfs_inode.c b/fs/xfs/xfs_inode.c
index 1f22d65fed0..da428b3fe0f 100644
--- a/fs/xfs/xfs_inode.c
+++ b/fs/xfs/xfs_inode.c
@@ -343,6 +343,16 @@ xfs_iformat(
 		return XFS_ERROR(EFSCORRUPTED);
 	}
 
+	if (unlikely((ip->i_d.di_flags & XFS_DIFLAG_REALTIME) &&
+		     !ip->i_mount->m_rtdev_targp)) {
+		xfs_fs_repair_cmn_err(CE_WARN, ip->i_mount,
+			"corrupt dinode %Lu, has realtime flag set.",
+			ip->i_ino);
+		XFS_CORRUPTION_ERROR("xfs_iformat(realtime)",
+				     XFS_ERRLEVEL_LOW, ip->i_mount, dip);
+		return XFS_ERROR(EFSCORRUPTED);
+	}
+
 	switch (ip->i_d.di_mode & S_IFMT) {
 	case S_IFIFO:
 	case S_IFCHR:
-- 
GitLab


From a8914f3a6d72c97328597a556a99daaf5cc288ae Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@lst.de>
Date: Mon, 10 Aug 2009 11:32:44 -0300
Subject: [PATCH 0780/1153] xfs: fix spin_is_locked assert on uni-processor
 builds

Without SMP or preemption spin_is_locked always returns false,
so we can't do an assert with it.  Instead use assert_spin_locked,
which does the right thing on all builds.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reported-by: Johannes Engel <jcnengel@googlemail.com>
Tested-by: Johannes Engel <jcnengel@googlemail.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/xfs_log.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/xfs/xfs_log.c b/fs/xfs/xfs_log.c
index 3750f04ede0..9dbdff3ea48 100644
--- a/fs/xfs/xfs_log.c
+++ b/fs/xfs/xfs_log.c
@@ -3180,7 +3180,7 @@ try_again:
 STATIC void
 xlog_state_want_sync(xlog_t *log, xlog_in_core_t *iclog)
 {
-	ASSERT(spin_is_locked(&log->l_icloglock));
+	assert_spin_locked(&log->l_icloglock);
 
 	if (iclog->ic_state == XLOG_STATE_ACTIVE) {
 		xlog_state_switch_iclogs(log, iclog, 0);
-- 
GitLab


From ec8b4b7085605e801a7740a2c3c33256aebe249c Mon Sep 17 00:00:00 2001
From: Stephen Kitt <steve@sk2.org>
Date: Wed, 12 Aug 2009 01:12:08 -0700
Subject: [PATCH 0781/1153] Input: joydev - decouple axis and button map ioctls
 from input constants

The KEY_MAX change in 2.6.28 changed the values of the JSIOCSBTNMAP and
JSIOCGBTNMAP constants; software compiled with the old values no longer
works with kernels following 2.6.28, because the ioctl switch statement
no longer matches the values given by the software. This patch handles
these ioctls independently of the length of data specified, and applies the
same treatment to JSIOCSAXMAP and JSIOCGAXMAP which currently depend on
ABS_MAX.

Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
---
 drivers/input/joydev.c | 68 +++++++++++++++++++++++++-----------------
 1 file changed, 41 insertions(+), 27 deletions(-)

diff --git a/drivers/input/joydev.c b/drivers/input/joydev.c
index 4cfd084fa89..9a1d55b74d7 100644
--- a/drivers/input/joydev.c
+++ b/drivers/input/joydev.c
@@ -456,8 +456,11 @@ static int joydev_ioctl_common(struct joydev *joydev,
 				unsigned int cmd, void __user *argp)
 {
 	struct input_dev *dev = joydev->handle.dev;
+	size_t len;
 	int i, j;
+	const char *name;
 
+	/* Process fixed-sized commands. */
 	switch (cmd) {
 
 	case JS_SET_CAL:
@@ -499,9 +502,22 @@ static int joydev_ioctl_common(struct joydev *joydev,
 		return copy_to_user(argp, joydev->corr,
 			sizeof(joydev->corr[0]) * joydev->nabs) ? -EFAULT : 0;
 
-	case JSIOCSAXMAP:
-		if (copy_from_user(joydev->abspam, argp,
-				   sizeof(__u8) * (ABS_MAX + 1)))
+	}
+
+	/*
+	 * Process variable-sized commands (the axis and button map commands
+	 * are considered variable-sized to decouple them from the values of
+	 * ABS_MAX and KEY_MAX).
+	 */
+	switch (cmd & ~IOCSIZE_MASK) {
+
+	case (JSIOCSAXMAP & ~IOCSIZE_MASK):
+		len = min_t(size_t, _IOC_SIZE(cmd), sizeof(joydev->abspam));
+		/*
+		 * FIXME: we should not copy into our axis map before
+		 * validating the data.
+		 */
+		if (copy_from_user(joydev->abspam, argp, len))
 			return -EFAULT;
 
 		for (i = 0; i < joydev->nabs; i++) {
@@ -511,13 +527,17 @@ static int joydev_ioctl_common(struct joydev *joydev,
 		}
 		return 0;
 
-	case JSIOCGAXMAP:
-		return copy_to_user(argp, joydev->abspam,
-			sizeof(__u8) * (ABS_MAX + 1)) ? -EFAULT : 0;
-
-	case JSIOCSBTNMAP:
-		if (copy_from_user(joydev->keypam, argp,
-				   sizeof(__u16) * (KEY_MAX - BTN_MISC + 1)))
+	case (JSIOCGAXMAP & ~IOCSIZE_MASK):
+		len = min_t(size_t, _IOC_SIZE(cmd), sizeof(joydev->abspam));
+		return copy_to_user(argp, joydev->abspam, len) ? -EFAULT : 0;
+
+	case (JSIOCSBTNMAP & ~IOCSIZE_MASK):
+		len = min_t(size_t, _IOC_SIZE(cmd), sizeof(joydev->keypam));
+		/*
+		 * FIXME: we should not copy into our keymap before
+		 * validating the data.
+		 */
+		if (copy_from_user(joydev->keypam, argp, len))
 			return -EFAULT;
 
 		for (i = 0; i < joydev->nkey; i++) {
@@ -529,25 +549,19 @@ static int joydev_ioctl_common(struct joydev *joydev,
 
 		return 0;
 
-	case JSIOCGBTNMAP:
-		return copy_to_user(argp, joydev->keypam,
-			sizeof(__u16) * (KEY_MAX - BTN_MISC + 1)) ? -EFAULT : 0;
+	case (JSIOCGBTNMAP & ~IOCSIZE_MASK):
+		len = min_t(size_t, _IOC_SIZE(cmd), sizeof(joydev->keypam));
+		return copy_to_user(argp, joydev->keypam, len) ? -EFAULT : 0;
 
-	default:
-		if ((cmd & ~IOCSIZE_MASK) == JSIOCGNAME(0)) {
-			int len;
-			const char *name = dev->name;
-
-			if (!name)
-				return 0;
-			len = strlen(name) + 1;
-			if (len > _IOC_SIZE(cmd))
-				len = _IOC_SIZE(cmd);
-			if (copy_to_user(argp, name, len))
-				return -EFAULT;
-			return len;
-		}
+	case JSIOCGNAME(0):
+		name = dev->name;
+		if (!name)
+			return 0;
+
+		len = min_t(size_t, _IOC_SIZE(cmd), strlen(name) + 1);
+		return copy_to_user(argp, name, len) ? -EFAULT : len;
 	}
+
 	return -EINVAL;
 }
 
-- 
GitLab


From e8055139d996e85722984968472868d6dccb1490 Mon Sep 17 00:00:00 2001
From: Ondrej Zary <linux@rainbow-software.org>
Date: Tue, 11 Aug 2009 20:00:11 +0200
Subject: [PATCH 0782/1153] x86: Fix oops in identify_cpu() on CPUs without
 CPUID

Kernel is broken for x86 CPUs without CPUID since 2.6.28. It
crashes with NULL pointer dereference in identify_cpu():

766        generic_identify(c);
767
768-->     if (this_cpu->c_identify)
769               this_cpu->c_identify(c);

this_cpu is NULL. This is because it's only initialized in
get_cpu_vendor() function, which is not called if the CPU has
no CPUID instruction.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
LKML-Reference: <200908112000.15993.linux@rainbow-software.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/cpu/common.c | 48 ++++++++++++++++++------------------
 1 file changed, 24 insertions(+), 24 deletions(-)

diff --git a/arch/x86/kernel/cpu/common.c b/arch/x86/kernel/cpu/common.c
index f1961c07af9..5ce60a88027 100644
--- a/arch/x86/kernel/cpu/common.c
+++ b/arch/x86/kernel/cpu/common.c
@@ -59,7 +59,30 @@ void __init setup_cpu_local_masks(void)
 	alloc_bootmem_cpumask_var(&cpu_sibling_setup_mask);
 }
 
-static const struct cpu_dev *this_cpu __cpuinitdata;
+static void __cpuinit default_init(struct cpuinfo_x86 *c)
+{
+#ifdef CONFIG_X86_64
+	display_cacheinfo(c);
+#else
+	/* Not much we can do here... */
+	/* Check if at least it has cpuid */
+	if (c->cpuid_level == -1) {
+		/* No cpuid. It must be an ancient CPU */
+		if (c->x86 == 4)
+			strcpy(c->x86_model_id, "486");
+		else if (c->x86 == 3)
+			strcpy(c->x86_model_id, "386");
+	}
+#endif
+}
+
+static const struct cpu_dev __cpuinitconst default_cpu = {
+	.c_init		= default_init,
+	.c_vendor	= "Unknown",
+	.c_x86_vendor	= X86_VENDOR_UNKNOWN,
+};
+
+static const struct cpu_dev *this_cpu __cpuinitdata = &default_cpu;
 
 DEFINE_PER_CPU_PAGE_ALIGNED(struct gdt_page, gdt_page) = { .gdt = {
 #ifdef CONFIG_X86_64
@@ -332,29 +355,6 @@ void switch_to_new_gdt(int cpu)
 
 static const struct cpu_dev *__cpuinitdata cpu_devs[X86_VENDOR_NUM] = {};
 
-static void __cpuinit default_init(struct cpuinfo_x86 *c)
-{
-#ifdef CONFIG_X86_64
-	display_cacheinfo(c);
-#else
-	/* Not much we can do here... */
-	/* Check if at least it has cpuid */
-	if (c->cpuid_level == -1) {
-		/* No cpuid. It must be an ancient CPU */
-		if (c->x86 == 4)
-			strcpy(c->x86_model_id, "486");
-		else if (c->x86 == 3)
-			strcpy(c->x86_model_id, "386");
-	}
-#endif
-}
-
-static const struct cpu_dev __cpuinitconst default_cpu = {
-	.c_init	= default_init,
-	.c_vendor = "Unknown",
-	.c_x86_vendor = X86_VENDOR_UNKNOWN,
-};
-
 static void __cpuinit get_model_name(struct cpuinfo_x86 *c)
 {
 	unsigned int *v;
-- 
GitLab


From df9eba8c9febf53782ef896518e7177999d98188 Mon Sep 17 00:00:00 2001
From: Tejun Heo <tj@kernel.org>
Date: Fri, 7 Aug 2009 11:15:20 +0900
Subject: [PATCH 0783/1153] pata_at91: fix resource release

Julias Lawall discovered that pata_at91 wasn't freeing a memory region
allocated with kzalloc() on init failure paths.  Upon review,
pata_at91 also seems to be doing unnecessary explicit resource
releases for managed resources too.  Convert memory allocation to
managed one and drop unnecessary explicit resource releases.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Julia Lawall <julia@diku.dk>
Cc: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/pata_at91.c | 17 ++++-------------
 1 file changed, 4 insertions(+), 13 deletions(-)

diff --git a/drivers/ata/pata_at91.c b/drivers/ata/pata_at91.c
index 5702affcb32..41c94b1ae49 100644
--- a/drivers/ata/pata_at91.c
+++ b/drivers/ata/pata_at91.c
@@ -250,7 +250,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev)
 		ata_port_desc(ap, "no IRQ, using PIO polling");
 	}
 
-	info = kzalloc(sizeof(*info), GFP_KERNEL);
+	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
 
 	if (!info) {
 		dev_err(dev, "failed to allocate memory for private data\n");
@@ -275,7 +275,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev)
 	if (!info->ide_addr) {
 		dev_err(dev, "failed to map IO base\n");
 		ret = -ENOMEM;
-		goto err_ide_ioremap;
+		goto err_put;
 	}
 
 	info->alt_addr = devm_ioremap(dev,
@@ -284,7 +284,7 @@ static int __devinit pata_at91_probe(struct platform_device *pdev)
 	if (!info->alt_addr) {
 		dev_err(dev, "failed to map CTL base\n");
 		ret = -ENOMEM;
-		goto err_alt_ioremap;
+		goto err_put;
 	}
 
 	ap->ioaddr.cmd_addr = info->ide_addr;
@@ -303,13 +303,8 @@ static int __devinit pata_at91_probe(struct platform_device *pdev)
 			irq ? ata_sff_interrupt : NULL,
 			irq_flags, &pata_at91_sht);
 
-err_alt_ioremap:
-	devm_iounmap(dev, info->ide_addr);
-
-err_ide_ioremap:
+err_put:
 	clk_put(info->mck);
-	kfree(info);
-
 	return ret;
 }
 
@@ -317,7 +312,6 @@ static int __devexit pata_at91_remove(struct platform_device *pdev)
 {
 	struct ata_host *host = dev_get_drvdata(&pdev->dev);
 	struct at91_ide_info *info;
-	struct device *dev = &pdev->dev;
 
 	if (!host)
 		return 0;
@@ -328,11 +322,8 @@ static int __devexit pata_at91_remove(struct platform_device *pdev)
 	if (!info)
 		return 0;
 
-	devm_iounmap(dev, info->ide_addr);
-	devm_iounmap(dev, info->alt_addr);
 	clk_put(info->mck);
 
-	kfree(info);
 	return 0;
 }
 
-- 
GitLab


From 1fd4bbec8c0d6db96b02141f324066afa2e77e89 Mon Sep 17 00:00:00 2001
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Thu, 6 Aug 2009 17:47:05 +0200
Subject: [PATCH 0784/1153] pata_atiixp: fix second channel support

PIO and MWDMA timings are never programmed for the second channel
because timing registers are treated as 16-bit long ones.

The bug is an attixp -> pata_atiixp regression and goes back to:

	commit 669a5db411d85a14f86cd92bc16bf7ab5b8aa235
	Author: Jeff Garzik <jeff@garzik.org>
	Date:   Tue Aug 29 18:12:40 2006 -0400

	    [libata] Add a bunch of PATA drivers.

Cc: Krystian Juskowiak <jusko@tlen.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/pata_atiixp.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/ata/pata_atiixp.c b/drivers/ata/pata_atiixp.c
index bec0b8ade66..45915566e4e 100644
--- a/drivers/ata/pata_atiixp.c
+++ b/drivers/ata/pata_atiixp.c
@@ -1,6 +1,7 @@
 /*
  * pata_atiixp.c 	- ATI PATA for new ATA layer
  *			  (C) 2005 Red Hat Inc
+ *			  (C) 2009 Bartlomiej Zolnierkiewicz
  *
  * Based on
  *
@@ -61,20 +62,19 @@ static void atiixp_set_pio_timing(struct ata_port *ap, struct ata_device *adev,
 
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 	int dn = 2 * ap->port_no + adev->devno;
-
-	/* Check this is correct - the order is odd in both drivers */
 	int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1);
-	u16 pio_mode_data, pio_timing_data;
+	u32 pio_timing_data;
+	u16 pio_mode_data;
 
 	pci_read_config_word(pdev, ATIIXP_IDE_PIO_MODE, &pio_mode_data);
 	pio_mode_data &= ~(0x7 << (4 * dn));
 	pio_mode_data |= pio << (4 * dn);
 	pci_write_config_word(pdev, ATIIXP_IDE_PIO_MODE, pio_mode_data);
 
-	pci_read_config_word(pdev, ATIIXP_IDE_PIO_TIMING, &pio_timing_data);
+	pci_read_config_dword(pdev, ATIIXP_IDE_PIO_TIMING, &pio_timing_data);
 	pio_timing_data &= ~(0xFF << timing_shift);
 	pio_timing_data |= (pio_timings[pio] << timing_shift);
-	pci_write_config_word(pdev, ATIIXP_IDE_PIO_TIMING, pio_timing_data);
+	pci_write_config_dword(pdev, ATIIXP_IDE_PIO_TIMING, pio_timing_data);
 }
 
 /**
@@ -119,16 +119,17 @@ static void atiixp_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 		udma_mode_data |= dma << (4 * dn);
 		pci_write_config_word(pdev, ATIIXP_IDE_UDMA_MODE, udma_mode_data);
 	} else {
-		u16 mwdma_timing_data;
-		/* Check this is correct - the order is odd in both drivers */
 		int timing_shift = (16 * ap->port_no) + 8 * (adev->devno ^ 1);
+		u32 mwdma_timing_data;
 
 		dma -= XFER_MW_DMA_0;
 
-		pci_read_config_word(pdev, ATIIXP_IDE_MWDMA_TIMING, &mwdma_timing_data);
+		pci_read_config_dword(pdev, ATIIXP_IDE_MWDMA_TIMING,
+				      &mwdma_timing_data);
 		mwdma_timing_data &= ~(0xFF << timing_shift);
 		mwdma_timing_data |= (mwdma_timings[dma] << timing_shift);
-		pci_write_config_word(pdev, ATIIXP_IDE_MWDMA_TIMING, mwdma_timing_data);
+		pci_write_config_dword(pdev, ATIIXP_IDE_MWDMA_TIMING,
+				       mwdma_timing_data);
 	}
 	/*
 	 *	We must now look at the PIO mode situation. We may need to
-- 
GitLab


From 7831387bda72af3059be48d39846d3eb6d8ce2f6 Mon Sep 17 00:00:00 2001
From: Tejun Heo <tj@kernel.org>
Date: Fri, 7 Aug 2009 01:59:15 +0900
Subject: [PATCH 0785/1153] libata: OCZ Vertex can't do HPA

OCZ Vertex SSD can't do HPA and not in a usual way.  It reports HPA,
allows unlocking but then fails all IOs which fall in the unlocked
area.  Quirk it so that HPA unlocking is not used for the device.

Reported by Daniel Perup in bnc#522414.

 https://bugzilla.novell.com/show_bug.cgi?id=522414

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Daniel Perup <probe@spray.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/libata-core.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 8ac98ff16d7..072ba5ea138 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4302,6 +4302,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
 	{ "WDC WD2500JD-00HBB0", "WD-WMAL71490727", ATA_HORKAGE_BROKEN_HPA },
 	{ "MAXTOR 6L080L4",	"A93.0500",	ATA_HORKAGE_BROKEN_HPA },
 
+	/* this one allows HPA unlocking but fails IOs on the area */
+	{ "OCZ-VERTEX",		    "1.30",	ATA_HORKAGE_BROKEN_HPA },
+
 	/* Devices which report 1 sector over size HPA */
 	{ "ST340823A",		NULL,		ATA_HORKAGE_HPA_SIZE, },
 	{ "ST320413A",		NULL,		ATA_HORKAGE_HPA_SIZE, },
-- 
GitLab


From 51c8949950647afeeb897e08dd75ad99078adb50 Mon Sep 17 00:00:00 2001
From: Tony Vroon <tony@linx.net>
Date: Thu, 6 Aug 2009 00:50:09 +0100
Subject: [PATCH 0786/1153] sata_nv: MSI support, disabled by default

At least the nVidia MCP55 controller quite happily supports MSI.
This adds an option to use it. It is disabled by default.
As per feedback by Robert Hancock, it will honour the user
request as the kernel will not enable MSI where the controller
or the specific system configuration do not support it.

Signed-off-by: Tony Vroon <tony@linx.net>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/sata_nv.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index b2d11f300c3..86a40582999 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -602,6 +602,7 @@ MODULE_VERSION(DRV_VERSION);
 
 static int adma_enabled;
 static int swncq_enabled = 1;
+static int msi_enabled;
 
 static void nv_adma_register_mode(struct ata_port *ap)
 {
@@ -2459,6 +2460,11 @@ static int nv_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	} else if (type == SWNCQ)
 		nv_swncq_host_init(host);
 
+	if (msi_enabled) {
+		dev_printk(KERN_NOTICE, &pdev->dev, "Using MSI\n");
+		pci_enable_msi(pdev);
+	}
+
 	pci_set_master(pdev);
 	return ata_host_activate(host, pdev->irq, ipriv->irq_handler,
 				 IRQF_SHARED, ipriv->sht);
@@ -2558,4 +2564,6 @@ module_param_named(adma, adma_enabled, bool, 0444);
 MODULE_PARM_DESC(adma, "Enable use of ADMA (Default: false)");
 module_param_named(swncq, swncq_enabled, bool, 0444);
 MODULE_PARM_DESC(swncq, "Enable use of SWNCQ (Default: true)");
+module_param_named(msi, msi_enabled, bool, 0444);
+MODULE_PARM_DESC(msi, "Enable use of MSI (Default: false)");
 
-- 
GitLab


From 20308871588518b5e209c403de2a3ad9a2eba9af Mon Sep 17 00:00:00 2001
From: Michael Prokop <mika@grml.org>
Date: Thu, 6 Aug 2009 00:14:10 +0200
Subject: [PATCH 0787/1153] Documentation/kernel-parameters.txt: document
 libata's ignore_hpa option

By default the kernel honors the HPA (host protected area) of hard
drives.  Using libata's ignore_hpa module option it's possible to
change this behaviour.

Document usage and options of libata.ignore_hpa in
Documentation/kernel-parameters.txt.

Signed-off-by: Michael Prokop <mika@grml.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 Documentation/kernel-parameters.txt | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index dd1a6d4bb74..7936b801fe6 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1115,6 +1115,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			libata.dma=4	  Compact Flash DMA only 
 			Combinations also work, so libata.dma=3 enables DMA
 			for disks and CDROMs, but not CFs.
+	
+	libata.ignore_hpa=	[LIBATA] Ignore HPA limit
+			libata.ignore_hpa=0	  keep BIOS limits (default)
+			libata.ignore_hpa=1	  ignore limits, using full disk
 
 	libata.noacpi	[LIBATA] Disables use of ACPI in libata suspend/resume
 			when set.
-- 
GitLab


From b6931c1fbaf7fda9ea7f120228a96600d7090049 Mon Sep 17 00:00:00 2001
From: Shane Huang <shane.huang@amd.com>
Date: Wed, 5 Aug 2009 10:10:41 +0800
Subject: [PATCH 0788/1153] ahci: Soften up the dmesg on SB600 PMP softreset
 failure recovery

Too strong words led to spurious bug reports: Novell bugzilla #527748,
RedHat bugzilla #468800. This patch is used to soften up the dmesg on
SB600 PMP softreset failure recovery, so as to remove the scariness and
concern from community.

Reported-by: pgnet Dev <pgnet.dev@gmail.com>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/ahci.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 958c1fa4190..838ff73b08e 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -1773,7 +1773,8 @@ static int ahci_sb600_softreset(struct ata_link *link, unsigned int *class,
 		irq_sts = readl(port_mmio + PORT_IRQ_STAT);
 		if (irq_sts & PORT_IRQ_BAD_PMP) {
 			ata_link_printk(link, KERN_WARNING,
-					"failed due to HW bug, retry pmp=0\n");
+					"applying SB600 PMP SRST workaround "
+					"and retrying\n");
 			rc = ahci_do_softreset(link, class, 0, deadline,
 					       ahci_check_ready);
 		}
-- 
GitLab


From 5594639aab8b5614cb27a3e5b2b627505cbcd137 Mon Sep 17 00:00:00 2001
From: Tejun Heo <tj@kernel.org>
Date: Tue, 4 Aug 2009 14:30:08 +0900
Subject: [PATCH 0789/1153] ahci: add workaround for on-board 5723s on some
 gigabyte boards

Some gigabytes have on-board SIMG5723s connected to JMB ahcis.  These
are used to implement hardware raid.  Unfortunately some firmware
revisions on these 5723s don't bring the link down when all the
downstream ports are unoccupied while not responding to reset protocol
which makes libata think that there's device attached to the port but
is not responding and retry.  This results in painfully wrong boot
detection time for these ports when they're empty.

This patch quirks those boards such that ahci gives up after the
initial timeout.  Combined with parallel probing, this gives quick
enough probing and also is safe because SIMG5723 will respond to the
first try if any of the downstream ports is occupied.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marc Bowes <marcbowes@gmail.com>
Reported-by: Nicolas Mailhot <Nicolas.Mailhot@LaPoste.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/ata/ahci.c | 76 +++++++++++++++++++++++++++++++++++++++++++---
 1 file changed, 72 insertions(+), 4 deletions(-)

diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 838ff73b08e..fe3eba5d6b3 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -219,6 +219,8 @@ enum {
 	AHCI_HFLAG_SECT255		= (1 << 8), /* max 255 sectors */
 	AHCI_HFLAG_YES_NCQ		= (1 << 9), /* force NCQ cap on */
 	AHCI_HFLAG_NO_SUSPEND		= (1 << 10), /* don't suspend */
+	AHCI_HFLAG_SRST_TOUT_IS_OFFLINE	= (1 << 11), /* treat SRST timeout as
+							link offline */
 
 	/* ap->flags bits */
 
@@ -1663,6 +1665,7 @@ static int ahci_do_softreset(struct ata_link *link, unsigned int *class,
 			     int (*check_ready)(struct ata_link *link))
 {
 	struct ata_port *ap = link->ap;
+	struct ahci_host_priv *hpriv = ap->host->private_data;
 	const char *reason = NULL;
 	unsigned long now, msecs;
 	struct ata_taskfile tf;
@@ -1701,12 +1704,21 @@ static int ahci_do_softreset(struct ata_link *link, unsigned int *class,
 
 	/* wait for link to become ready */
 	rc = ata_wait_after_reset(link, deadline, check_ready);
-	/* link occupied, -ENODEV too is an error */
-	if (rc) {
+	if (rc == -EBUSY && hpriv->flags & AHCI_HFLAG_SRST_TOUT_IS_OFFLINE) {
+		/*
+		 * Workaround for cases where link online status can't
+		 * be trusted.  Treat device readiness timeout as link
+		 * offline.
+		 */
+		ata_link_printk(link, KERN_INFO,
+				"device not ready, treating as offline\n");
+		*class = ATA_DEV_NONE;
+	} else if (rc) {
+		/* link occupied, -ENODEV too is an error */
 		reason = "device not ready";
 		goto fail;
-	}
-	*class = ahci_dev_classify(ap);
+	} else
+		*class = ahci_dev_classify(ap);
 
 	DPRINTK("EXIT, class=%u\n", *class);
 	return 0;
@@ -2727,6 +2739,56 @@ static bool ahci_broken_suspend(struct pci_dev *pdev)
 	return !ver || strcmp(ver, dmi->driver_data) < 0;
 }
 
+static bool ahci_broken_online(struct pci_dev *pdev)
+{
+#define ENCODE_BUSDEVFN(bus, slot, func)			\
+	(void *)(unsigned long)(((bus) << 8) | PCI_DEVFN((slot), (func)))
+	static const struct dmi_system_id sysids[] = {
+		/*
+		 * There are several gigabyte boards which use
+		 * SIMG5723s configured as hardware RAID.  Certain
+		 * 5723 firmware revisions shipped there keep the link
+		 * online but fail to answer properly to SRST or
+		 * IDENTIFY when no device is attached downstream
+		 * causing libata to retry quite a few times leading
+		 * to excessive detection delay.
+		 *
+		 * As these firmwares respond to the second reset try
+		 * with invalid device signature, considering unknown
+		 * sig as offline works around the problem acceptably.
+		 */
+		{
+			.ident = "EP45-DQ6",
+			.matches = {
+				DMI_MATCH(DMI_BOARD_VENDOR,
+					  "Gigabyte Technology Co., Ltd."),
+				DMI_MATCH(DMI_BOARD_NAME, "EP45-DQ6"),
+			},
+			.driver_data = ENCODE_BUSDEVFN(0x0a, 0x00, 0),
+		},
+		{
+			.ident = "EP45-DS5",
+			.matches = {
+				DMI_MATCH(DMI_BOARD_VENDOR,
+					  "Gigabyte Technology Co., Ltd."),
+				DMI_MATCH(DMI_BOARD_NAME, "EP45-DS5"),
+			},
+			.driver_data = ENCODE_BUSDEVFN(0x03, 0x00, 0),
+		},
+		{ }	/* terminate list */
+	};
+#undef ENCODE_BUSDEVFN
+	const struct dmi_system_id *dmi = dmi_first_match(sysids);
+	unsigned int val;
+
+	if (!dmi)
+		return false;
+
+	val = (unsigned long)dmi->driver_data;
+
+	return pdev->bus->number == (val >> 8) && pdev->devfn == (val & 0xff);
+}
+
 static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	static int printed_version;
@@ -2842,6 +2904,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 			   "BIOS update required for suspend/resume\n");
 	}
 
+	if (ahci_broken_online(pdev)) {
+		hpriv->flags |= AHCI_HFLAG_SRST_TOUT_IS_OFFLINE;
+		dev_info(&pdev->dev,
+			 "online status unreliable, applying workaround\n");
+	}
+
 	/* CAP.NP sometimes indicate the index of the last enabled
 	 * port, at other times, that of the last possible port, so
 	 * determining the maximum port number requires looking at
-- 
GitLab


From 67fe0688082509c52bd451d10a61b3565169c23e Mon Sep 17 00:00:00 2001
From: Jeff Garzik <jeff@garzik.org>
Date: Wed, 12 Aug 2009 06:29:57 -0400
Subject: [PATCH 0790/1153] Remove zero-length file drivers/mtd/maps/sbc8240.c

It was "deleted" in commit 2bf961b7ccd69e108ac435c67e2b0522b403c578

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
---
 drivers/mtd/maps/sbc8240.c | 0
 1 file changed, 0 insertions(+), 0 deletions(-)
 delete mode 100644 drivers/mtd/maps/sbc8240.c

diff --git a/drivers/mtd/maps/sbc8240.c b/drivers/mtd/maps/sbc8240.c
deleted file mode 100644
index e69de29bb2d..00000000000
-- 
GitLab


From 2a8083f063472f27c253545dd64e1a7bbbb1ab61 Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Tue, 11 Aug 2009 16:22:00 -0300
Subject: [PATCH 0791/1153] perf record: Fix .tid and .pid fill-in when
 synthesizing events
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Noticed when trying to record events for a firefox thread. We
were synthesizing both .tid and .pid with the pid passed via
--pid.

Fix it by reading /proc/PID/status and getting the tgid
to use in .pid, .tid gets the specified "pid".

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <20090811192200.GF18061@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-record.c | 71 ++++++++++++++++++++-----------------
 1 file changed, 38 insertions(+), 33 deletions(-)

diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c
index 0345aad8eba..30b83def03d 100644
--- a/tools/perf/builtin-record.c
+++ b/tools/perf/builtin-record.c
@@ -203,46 +203,48 @@ static void sig_atexit(void)
 	kill(getpid(), signr);
 }
 
-static void pid_synthesize_comm_event(pid_t pid, int full)
+static pid_t pid_synthesize_comm_event(pid_t pid, int full)
 {
 	struct comm_event comm_ev;
 	char filename[PATH_MAX];
 	char bf[BUFSIZ];
-	int fd;
-	size_t size;
-	char *field, *sep;
+	FILE *fp;
+	size_t size = 0;
 	DIR *tasks;
 	struct dirent dirent, *next;
+	pid_t tgid = 0;
 
-	snprintf(filename, sizeof(filename), "/proc/%d/stat", pid);
+	snprintf(filename, sizeof(filename), "/proc/%d/status", pid);
 
-	fd = open(filename, O_RDONLY);
-	if (fd < 0) {
+	fp = fopen(filename, "r");
+	if (fd == NULL) {
 		/*
 		 * We raced with a task exiting - just return:
 		 */
 		if (verbose)
 			fprintf(stderr, "couldn't open %s\n", filename);
-		return;
+		return 0;
 	}
-	if (read(fd, bf, sizeof(bf)) < 0) {
-		fprintf(stderr, "couldn't read %s\n", filename);
-		exit(EXIT_FAILURE);
-	}
-	close(fd);
 
-	/* 9027 (cat) R 6747 9027 6747 34816 9027 ... */
 	memset(&comm_ev, 0, sizeof(comm_ev));
-	field = strchr(bf, '(');
-	if (field == NULL)
-		goto out_failure;
-	sep = strchr(++field, ')');
-	if (sep == NULL)
-		goto out_failure;
-	size = sep - field;
-	memcpy(comm_ev.comm, field, size++);
-
-	comm_ev.pid = pid;
+	while (!comm_ev.comm[0] || !comm_ev.pid) {
+		if (fgets(bf, sizeof(bf), fp) == NULL)
+			goto out_failure;
+
+		if (memcmp(bf, "Name:", 5) == 0) {
+			char *name = bf + 5;
+			while (*name && isspace(*name))
+				++name;
+			size = strlen(name) - 1;
+			memcpy(comm_ev.comm, name, size++);
+		} else if (memcmp(bf, "Tgid:", 5) == 0) {
+			char *tgids = bf + 5;
+			while (*tgids && isspace(*tgids))
+				++tgids;
+			tgid = comm_ev.pid = atoi(tgids);
+		}
+	}
+
 	comm_ev.header.type = PERF_EVENT_COMM;
 	size = ALIGN(size, sizeof(u64));
 	comm_ev.header.size = sizeof(comm_ev) - (sizeof(comm_ev.comm) - size);
@@ -251,7 +253,7 @@ static void pid_synthesize_comm_event(pid_t pid, int full)
 		comm_ev.tid = pid;
 
 		write_output(&comm_ev, comm_ev.header.size);
-		return;
+		goto out_fclose;
 	}
 
 	snprintf(filename, sizeof(filename), "/proc/%d/task", pid);
@@ -268,7 +270,10 @@ static void pid_synthesize_comm_event(pid_t pid, int full)
 		write_output(&comm_ev, comm_ev.header.size);
 	}
 	closedir(tasks);
-	return;
+
+out_fclose:
+	fclose(fp);
+	return tgid;
 
 out_failure:
 	fprintf(stderr, "couldn't get COMM and pgid, malformed %s\n",
@@ -276,7 +281,7 @@ out_failure:
 	exit(EXIT_FAILURE);
 }
 
-static void pid_synthesize_mmap_samples(pid_t pid)
+static void pid_synthesize_mmap_samples(pid_t pid, pid_t tgid)
 {
 	char filename[PATH_MAX];
 	FILE *fp;
@@ -328,7 +333,7 @@ static void pid_synthesize_mmap_samples(pid_t pid)
 			mmap_ev.len -= mmap_ev.start;
 			mmap_ev.header.size = (sizeof(mmap_ev) -
 					       (sizeof(mmap_ev.filename) - size));
-			mmap_ev.pid = pid;
+			mmap_ev.pid = tgid;
 			mmap_ev.tid = pid;
 
 			write_output(&mmap_ev, mmap_ev.header.size);
@@ -347,14 +352,14 @@ static void synthesize_all(void)
 
 	while (!readdir_r(proc, &dirent, &next) && next) {
 		char *end;
-		pid_t pid;
+		pid_t pid, tgid;
 
 		pid = strtol(dirent.d_name, &end, 10);
 		if (*end) /* only interested in proper numerical dirents */
 			continue;
 
-		pid_synthesize_comm_event(pid, 1);
-		pid_synthesize_mmap_samples(pid);
+		tgid = pid_synthesize_comm_event(pid, 1);
+		pid_synthesize_mmap_samples(pid, tgid);
 	}
 
 	closedir(proc);
@@ -567,8 +572,8 @@ static int __cmd_record(int argc, const char **argv)
 		perf_header__write(header, output);
 
 	if (!system_wide) {
-		pid_synthesize_comm_event(pid, 0);
-		pid_synthesize_mmap_samples(pid);
+		pid_t tgid = pid_synthesize_comm_event(pid, 0);
+		pid_synthesize_mmap_samples(pid, tgid);
 	} else
 		synthesize_all();
 
-- 
GitLab


From 94a24752fe95ca1e7f98b197052d44e6a207740d Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Tue, 11 Aug 2009 16:21:38 -0300
Subject: [PATCH 0792/1153] perf report: Show the tid too in -D
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

This made it easier to find the firefox threading related
bug.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090811192138.GE18061@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-report.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index 99274cec0ad..23e1457f240 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -1526,11 +1526,11 @@ process_sample_event(event_t *event, unsigned long offset, unsigned long head)
 		more_data += sizeof(u64);
 	}
 
-	dprintf("%p [%p]: PERF_EVENT_SAMPLE (IP, %d): %d: %p period: %Ld\n",
+	dprintf("%p [%p]: PERF_EVENT_SAMPLE (IP, %d): %d/%d: %p period: %Ld\n",
 		(void *)(offset + head),
 		(void *)(long)(event->header.size),
 		event->header.misc,
-		event->ip.pid,
+		event->ip.pid, event->ip.tid,
 		(void *)(long)ip,
 		(long long)period);
 
@@ -1612,10 +1612,11 @@ process_mmap_event(event_t *event, unsigned long offset, unsigned long head)
 	struct thread *thread = threads__findnew(event->mmap.pid);
 	struct map *map = map__new(&event->mmap);
 
-	dprintf("%p [%p]: PERF_EVENT_MMAP %d: [%p(%p) @ %p]: %s\n",
+	dprintf("%p [%p]: PERF_EVENT_MMAP %d/%d: [%p(%p) @ %p]: %s\n",
 		(void *)(offset + head),
 		(void *)(long)(event->header.size),
 		event->mmap.pid,
+		event->mmap.tid,
 		(void *)(long)event->mmap.start,
 		(void *)(long)event->mmap.len,
 		(void *)(long)event->mmap.pgoff,
-- 
GitLab


From 247648e3742ded01e42a4b14c2da330b13cbb47f Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Tue, 11 Aug 2009 16:22:11 -0300
Subject: [PATCH 0793/1153] perf tools: Fix fallback to cplus_demangle() when
 bfd_demangle() is not available
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

In old binutils we can't access bfd_demangle(), use
cplus_demangle() just like oprofile.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Luis Claudio R. Gonçalves <lclaudio@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090811192211.GG18061@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Makefile      | 29 ++++++++++++++++++-----------
 tools/perf/util/symbol.c | 15 ---------------
 tools/perf/util/symbol.h | 24 ++++++++++++++++++++++++
 3 files changed, 42 insertions(+), 26 deletions(-)

diff --git a/tools/perf/Makefile b/tools/perf/Makefile
index 60411e94113..c045b4271e5 100644
--- a/tools/perf/Makefile
+++ b/tools/perf/Makefile
@@ -382,22 +382,29 @@ endif
 ifdef NO_DEMANGLE
 	BASIC_CFLAGS += -DNO_DEMANGLE
 else
-
 	has_bfd := $(shell sh -c "(echo '\#include <bfd.h>'; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd > /dev/null 2>&1 && echo y")
 
-	has_bfd_iberty := $(shell sh -c "(echo '\#include <bfd.h>'; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty > /dev/null 2>&1 && echo y")
-
-	has_bfd_iberty_z := $(shell sh -c "(echo '\#include <bfd.h>'; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty -lz > /dev/null 2>&1 && echo y")
-
 	ifeq ($(has_bfd),y)
 		EXTLIBS += -lbfd
-	else ifeq ($(has_bfd_iberty),y)
-		EXTLIBS += -lbfd -liberty
-	else ifeq ($(has_bfd_iberty_z),y)
-		EXTLIBS += -lbfd -liberty -lz
 	else
-		msg := $(warning No bfd.h/libbfd found, install binutils-dev[el] to gain symbol demangling)
-		BASIC_CFLAGS += -DNO_DEMANGLE
+		has_bfd_iberty := $(shell sh -c "(echo '\#include <bfd.h>'; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty > /dev/null 2>&1 && echo y")
+		ifeq ($(has_bfd_iberty),y)
+			EXTLIBS += -lbfd -liberty
+		else
+			has_bfd_iberty_z := $(shell sh -c "(echo '\#include <bfd.h>'; echo 'int main(void) { bfd_demangle(0, 0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -lbfd -liberty -lz > /dev/null 2>&1 && echo y")
+			ifeq ($(has_bfd_iberty_z),y)
+				EXTLIBS += -lbfd -liberty -lz
+			else
+				has_cplus_demangle := $(shell sh -c "(echo 'extern char *cplus_demangle(const char *, int);'; echo 'int main(void) { cplus_demangle(0, 0); return 0; }') | $(CC) -x c - $(ALL_CFLAGS) -o /dev/null $(ALL_LDFLAGS) -liberty > /dev/null 2>&1 && echo y")
+				ifeq ($(has_cplus_demangle),y)
+					EXTLIBS += -liberty
+					BASIC_CFLAGS += -DHAVE_CPLUS_DEMANGLE
+				else
+					msg := $(warning No bfd.h/libbfd found, install binutils-dev[el] to gain symbol demangling)
+					BASIC_CFLAGS += -DNO_DEMANGLE
+				endif
+			endif
+		endif
 	endif
 endif
 
diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c
index f1dcede1430..2473fd427be 100644
--- a/tools/perf/util/symbol.c
+++ b/tools/perf/util/symbol.c
@@ -7,23 +7,8 @@
 #include <gelf.h>
 #include <elf.h>
 
-#ifndef NO_DEMANGLE
-#include <bfd.h>
-#else
-static inline
-char *bfd_demangle(void __used *v, const char __used *c, int __used i)
-{
-	return NULL;
-}
-#endif
-
 const char *sym_hist_filter;
 
-#ifndef DMGL_PARAMS
-#define DMGL_PARAMS      (1 << 0)       /* Include function args */
-#define DMGL_ANSI        (1 << 1)       /* Include const, volatile, etc */
-#endif
-
 enum dso_origin {
 	DSO__ORIG_KERNEL = 0,
 	DSO__ORIG_JAVA_JIT,
diff --git a/tools/perf/util/symbol.h b/tools/perf/util/symbol.h
index 1e003ec2f4b..b53bf0125c1 100644
--- a/tools/perf/util/symbol.h
+++ b/tools/perf/util/symbol.h
@@ -7,6 +7,30 @@
 #include <linux/rbtree.h>
 #include "module.h"
 
+#ifdef HAVE_CPLUS_DEMANGLE
+extern char *cplus_demangle(const char *, int);
+
+static inline char *bfd_demangle(void __used *v, const char *c, int i)
+{
+	return cplus_demangle(c, i);
+}
+#else
+#ifdef NO_DEMANGLE
+static inline char *bfd_demangle(void __used *v, const char __used *c,
+				 int __used i)
+{
+	return NULL;
+}
+#else
+#include <bfd.h>
+#endif
+#endif
+
+#ifndef DMGL_PARAMS
+#define DMGL_PARAMS      (1 << 0)       /* Include function args */
+#define DMGL_ANSI        (1 << 1)       /* Include const, volatile, etc */
+#endif
+
 struct symbol {
 	struct rb_node	rb_node;
 	u64		start;
-- 
GitLab


From 1340e6bbaff7ff7f6f75eb4a5c34933efce84a84 Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Tue, 11 Aug 2009 17:04:36 -0300
Subject: [PATCH 0794/1153] perf tools: Fix dso__new handle() to handle deleted
 DSOs
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

It is better than showing the map addr, this way at least we
know that we can't get the symtabs because the DSO was deleted
(system update) while an app still used such DSO.

Yeah, don't do that, but if you do, you'll figure it out
quicker this way.

[acme@doppio linux-2.6-tip]$ perf report | head -15
 # Samples: 3796
 #
 # Overhead  Command                                                        Shared Object  Symbol
 # ........  .......  ...................................................................  ......
 #
    23.55%   pidgin  /lib64/libglib-2.0.so.0.2000.4.#prelink#.Pd98lu (deleted)            [.] 0x00000000038844
    21.55%   pidgin  /lib64/libpthread-2.10.1.so.#prelink#.AFwK8Q (deleted)               [.] 0x0000000000a42d
    10.85%   pidgin  [kernel]                                                             [.] vread_hpet
     7.85%   pidgin  /lib64/libgobject-2.0.so.0.2000.4.#prelink#.o1vpU7 (deleted)         [.] 0x00000000014de8
     3.35%   pidgin  /lib64/libc-2.10.1.so (deleted)                                      [.] 0x0000000007a875
     3.19%   pidgin  /lib64/libdbus-1.so.3.4.0.#prelink#.6mwgZP (deleted)                 [.] 0x0000000001d254
     3.06%   pidgin  /usr/lib64/libgtk-x11-2.0.so.0.1600.5.#prelink#.511hAl (deleted)     [.] 0x000000002334e7
     2.90%   pidgin  /usr/lib64/libgdk-x11-2.0.so.0.1600.5.#prelink#.5qlMo1 (deleted)     [.] 0x00000000037b2d
     1.84%   pidgin  [kernel]                                                             [k] do_sys_poll
     1.45%   pidgin  /usr/lib64/libX11.so.6.2.0.#prelink#.iR59Rx (deleted)                [.] 0x0000000004c751
[acme@doppio linux-2.6-tip]$

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Luis Claudio R. Gonçalves <lclaudio@redhat.com>
Cc: Clark Williams <williams@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090811200436.GA3478@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/util/symbol.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/tools/perf/util/symbol.c b/tools/perf/util/symbol.c
index 2473fd427be..5c0f42e6b33 100644
--- a/tools/perf/util/symbol.c
+++ b/tools/perf/util/symbol.c
@@ -801,6 +801,8 @@ more:
 	}
 out:
 	free(name);
+	if (ret < 0 && strstr(self->name, " (deleted)") != NULL)
+		return 0;
 	return ret;
 }
 
-- 
GitLab


From 0a5ac84650fb7a7f226814103d95724e34b012ae Mon Sep 17 00:00:00 2001
From: Jens Axboe <jens.axboe@oracle.com>
Date: Wed, 12 Aug 2009 11:18:01 +0200
Subject: [PATCH 0795/1153] perf record: Add missing -C option support for
 specifying profile cpu

perf top supports a -C for setting the profile CPU, but perf
record does not. This adds the same option for perf record,
allowing the user to specify a specific target profile CPU.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090812091801.GC12579@kernel.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-record.c | 17 ++++++++++++++---
 1 file changed, 14 insertions(+), 3 deletions(-)

diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c
index 30b83def03d..de76008fbaa 100644
--- a/tools/perf/builtin-record.c
+++ b/tools/perf/builtin-record.c
@@ -35,6 +35,7 @@ static const char		*output_name			= "perf.data";
 static int			group				= 0;
 static unsigned int		realtime_prio			= 0;
 static int			system_wide			= 0;
+static int			profile_cpu			= -1;
 static pid_t			target_pid			= -1;
 static int			inherit				= 1;
 static int			force				= 0;
@@ -431,6 +432,8 @@ try_again:
 
 		if (err == EPERM)
 			die("Permission error - are you root?\n");
+		else if (err ==  ENODEV && profile_cpu != -1)
+			die("No such device - did you specify an out-of-range profile CPU?\n");
 
 		/*
 		 * If it's cycles then fall back to hrtimer
@@ -564,9 +567,15 @@ static int __cmd_record(int argc, const char **argv)
 		if (pid == -1)
 			pid = getpid();
 
-		open_counters(-1, pid);
-	} else for (i = 0; i < nr_cpus; i++)
-		open_counters(i, target_pid);
+		open_counters(profile_cpu, pid);
+	} else {
+		if (profile_cpu != -1) {
+			open_counters(profile_cpu, target_pid);
+		} else {
+			for (i = 0; i < nr_cpus; i++)
+				open_counters(i, target_pid);
+		}
+	}
 
 	if (file_new)
 		perf_header__write(header, output);
@@ -645,6 +654,8 @@ static const struct option options[] = {
 			    "system-wide collection from all CPUs"),
 	OPT_BOOLEAN('A', "append", &append_file,
 			    "append to the output file to do incremental profiling"),
+	OPT_INTEGER('C', "profile_cpu", &profile_cpu,
+			    "CPU to profile on"),
 	OPT_BOOLEAN('f', "force", &force,
 			"overwrite existing data file"),
 	OPT_LONG('c', "count", &default_interval,
-- 
GitLab


From 04da8a43da804723a550f00dd158fd5b5e25ae35 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Tue, 11 Aug 2009 10:40:08 +0200
Subject: [PATCH 0796/1153] perf_counter, x86: Fix/improve apic fallback

Johannes Stezenbach reported that his Pentium-M based
laptop does not have the local APIC enabled by default,
and hence perfcounters do not get initialized.

Add a fallback for this case: allow non-sampled counters
and return with an error on sampled counters. This allows
'perf stat' to work out of box - and allows 'perf top'
and 'perf record' to fall back on a hrtimer based sampling
method.

( Passing 'lapic' on the boot line will allow hardware
  sampling to occur - but if the APIC is disabled
  permanently by the hardware then this fallback still
  allows more systems to use perfcounters. )

Also decouple perfcounter support from X86_LOCAL_APIC.

-v2: fix typo breaking counters on all other systems ...

Reported-by: Johannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/Kconfig                   |  2 +-
 arch/x86/kernel/cpu/perf_counter.c | 34 ++++++++++++++++++++++++++----
 2 files changed, 31 insertions(+), 5 deletions(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 738bdc6b0f8..13ffa5df37d 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -24,6 +24,7 @@ config X86
 	select HAVE_UNSTABLE_SCHED_CLOCK
 	select HAVE_IDE
 	select HAVE_OPROFILE
+	select HAVE_PERF_COUNTERS if (!M386 && !M486)
 	select HAVE_IOREMAP_PROT
 	select HAVE_KPROBES
 	select ARCH_WANT_OPTIONAL_GPIOLIB
@@ -742,7 +743,6 @@ config X86_UP_IOAPIC
 config X86_LOCAL_APIC
 	def_bool y
 	depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_APIC
-	select HAVE_PERF_COUNTERS if (!M386 && !M486)
 
 config X86_IO_APIC
 	def_bool y
diff --git a/arch/x86/kernel/cpu/perf_counter.c b/arch/x86/kernel/cpu/perf_counter.c
index fffc126dbdf..900332b800f 100644
--- a/arch/x86/kernel/cpu/perf_counter.c
+++ b/arch/x86/kernel/cpu/perf_counter.c
@@ -55,6 +55,7 @@ struct x86_pmu {
 	int		num_counters_fixed;
 	int		counter_bits;
 	u64		counter_mask;
+	int		apic;
 	u64		max_period;
 	u64		intel_ctrl;
 };
@@ -613,6 +614,7 @@ static DEFINE_MUTEX(pmc_reserve_mutex);
 
 static bool reserve_pmc_hardware(void)
 {
+#ifdef CONFIG_X86_LOCAL_APIC
 	int i;
 
 	if (nmi_watchdog == NMI_LOCAL_APIC)
@@ -627,9 +629,11 @@ static bool reserve_pmc_hardware(void)
 		if (!reserve_evntsel_nmi(x86_pmu.eventsel + i))
 			goto eventsel_fail;
 	}
+#endif
 
 	return true;
 
+#ifdef CONFIG_X86_LOCAL_APIC
 eventsel_fail:
 	for (i--; i >= 0; i--)
 		release_evntsel_nmi(x86_pmu.eventsel + i);
@@ -644,10 +648,12 @@ perfctr_fail:
 		enable_lapic_nmi_watchdog();
 
 	return false;
+#endif
 }
 
 static void release_pmc_hardware(void)
 {
+#ifdef CONFIG_X86_LOCAL_APIC
 	int i;
 
 	for (i = 0; i < x86_pmu.num_counters; i++) {
@@ -657,6 +663,7 @@ static void release_pmc_hardware(void)
 
 	if (nmi_watchdog == NMI_LOCAL_APIC)
 		enable_lapic_nmi_watchdog();
+#endif
 }
 
 static void hw_perf_counter_destroy(struct perf_counter *counter)
@@ -748,6 +755,15 @@ static int __hw_perf_counter_init(struct perf_counter *counter)
 		hwc->sample_period = x86_pmu.max_period;
 		hwc->last_period = hwc->sample_period;
 		atomic64_set(&hwc->period_left, hwc->sample_period);
+	} else {
+		/*
+		 * If we have a PMU initialized but no APIC
+		 * interrupts, we cannot sample hardware
+		 * counters (user-space has to fall back and
+		 * sample via a hrtimer based software counter):
+		 */
+		if (!x86_pmu.apic)
+			return -EOPNOTSUPP;
 	}
 
 	counter->destroy = hw_perf_counter_destroy;
@@ -1449,18 +1465,22 @@ void smp_perf_pending_interrupt(struct pt_regs *regs)
 
 void set_perf_counter_pending(void)
 {
+#ifdef CONFIG_X86_LOCAL_APIC
 	apic->send_IPI_self(LOCAL_PENDING_VECTOR);
+#endif
 }
 
 void perf_counters_lapic_init(void)
 {
-	if (!x86_pmu_initialized())
+#ifdef CONFIG_X86_LOCAL_APIC
+	if (!x86_pmu.apic || !x86_pmu_initialized())
 		return;
 
 	/*
 	 * Always use NMI for PMU
 	 */
 	apic_write(APIC_LVTPC, APIC_DM_NMI);
+#endif
 }
 
 static int __kprobes
@@ -1484,7 +1504,9 @@ perf_counter_nmi_handler(struct notifier_block *self,
 
 	regs = args->regs;
 
+#ifdef CONFIG_X86_LOCAL_APIC
 	apic_write(APIC_LVTPC, APIC_DM_NMI);
+#endif
 	/*
 	 * Can't rely on the handled return value to say it was our NMI, two
 	 * counters could trigger 'simultaneously' raising two back-to-back NMIs.
@@ -1515,6 +1537,7 @@ static struct x86_pmu p6_pmu = {
 	.event_map		= p6_pmu_event_map,
 	.raw_event		= p6_pmu_raw_event,
 	.max_events		= ARRAY_SIZE(p6_perfmon_event_map),
+	.apic			= 1,
 	.max_period		= (1ULL << 31) - 1,
 	.version		= 0,
 	.num_counters		= 2,
@@ -1541,6 +1564,7 @@ static struct x86_pmu intel_pmu = {
 	.event_map		= intel_pmu_event_map,
 	.raw_event		= intel_pmu_raw_event,
 	.max_events		= ARRAY_SIZE(intel_perfmon_event_map),
+	.apic			= 1,
 	/*
 	 * Intel PMCs cannot be accessed sanely above 32 bit width,
 	 * so we install an artificial 1<<31 period regardless of
@@ -1564,6 +1588,7 @@ static struct x86_pmu amd_pmu = {
 	.num_counters		= 4,
 	.counter_bits		= 48,
 	.counter_mask		= (1ULL << 48) - 1,
+	.apic			= 1,
 	/* use highest bit to detect overflow */
 	.max_period		= (1ULL << 47) - 1,
 };
@@ -1589,13 +1614,14 @@ static int p6_pmu_init(void)
 		return -ENODEV;
 	}
 
+	x86_pmu = p6_pmu;
+
 	if (!cpu_has_apic) {
 		pr_info("no APIC, boot with the \"lapic\" boot parameter to force-enable it.\n");
-		return -ENODEV;
+		pr_info("no hardware sampling interrupt available.\n");
+		x86_pmu.apic = 0;
 	}
 
-	x86_pmu				= p6_pmu;
-
 	return 0;
 }
 
-- 
GitLab


From 1ae88b2e446261c038f2c0c3150ffae142b227a2 Mon Sep 17 00:00:00 2001
From: Trond Myklebust <Trond.Myklebust@netapp.com>
Date: Wed, 12 Aug 2009 09:12:30 -0400
Subject: [PATCH 0797/1153] NFS: Fix an O_DIRECT Oops...

We can't call nfs_readdata_release()/nfs_writedata_release() without
first initialising and referencing args.context. Doing so inside
nfs_direct_read_schedule_segment()/nfs_direct_write_schedule_segment()
causes an Oops.

We should rather be calling nfs_readdata_free()/nfs_writedata_free() in
those cases.

Looking at the O_DIRECT code, the "struct nfs_direct_req" is already
referencing the nfs_open_context for us. Since the readdata and writedata
structures carry a reference to that, we can simplify things by getting rid
of the extra nfs_open_context references, so that we can replace all
instances of nfs_readdata_release()/nfs_writedata_release().

Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/nfs/direct.c        | 20 ++++++++++----------
 fs/nfs/read.c          |  6 ++----
 fs/nfs/write.c         |  6 ++----
 include/linux/nfs_fs.h |  5 ++---
 4 files changed, 16 insertions(+), 21 deletions(-)

diff --git a/fs/nfs/direct.c b/fs/nfs/direct.c
index 489fc01a320..e4e089a8f29 100644
--- a/fs/nfs/direct.c
+++ b/fs/nfs/direct.c
@@ -255,7 +255,7 @@ static void nfs_direct_read_release(void *calldata)
 
 	if (put_dreq(dreq))
 		nfs_direct_complete(dreq);
-	nfs_readdata_release(calldata);
+	nfs_readdata_free(data);
 }
 
 static const struct rpc_call_ops nfs_read_direct_ops = {
@@ -314,14 +314,14 @@ static ssize_t nfs_direct_read_schedule_segment(struct nfs_direct_req *dreq,
 					data->npages, 1, 0, data->pagevec, NULL);
 		up_read(&current->mm->mmap_sem);
 		if (result < 0) {
-			nfs_readdata_release(data);
+			nfs_readdata_free(data);
 			break;
 		}
 		if ((unsigned)result < data->npages) {
 			bytes = result * PAGE_SIZE;
 			if (bytes <= pgbase) {
 				nfs_direct_release_pages(data->pagevec, result);
-				nfs_readdata_release(data);
+				nfs_readdata_free(data);
 				break;
 			}
 			bytes -= pgbase;
@@ -334,7 +334,7 @@ static ssize_t nfs_direct_read_schedule_segment(struct nfs_direct_req *dreq,
 		data->inode = inode;
 		data->cred = msg.rpc_cred;
 		data->args.fh = NFS_FH(inode);
-		data->args.context = get_nfs_open_context(ctx);
+		data->args.context = ctx;
 		data->args.offset = pos;
 		data->args.pgbase = pgbase;
 		data->args.pages = data->pagevec;
@@ -441,7 +441,7 @@ static void nfs_direct_free_writedata(struct nfs_direct_req *dreq)
 		struct nfs_write_data *data = list_entry(dreq->rewrite_list.next, struct nfs_write_data, pages);
 		list_del(&data->pages);
 		nfs_direct_release_pages(data->pagevec, data->npages);
-		nfs_writedata_release(data);
+		nfs_writedata_free(data);
 	}
 }
 
@@ -534,7 +534,7 @@ static void nfs_direct_commit_release(void *calldata)
 
 	dprintk("NFS: %5u commit returned %d\n", data->task.tk_pid, status);
 	nfs_direct_write_complete(dreq, data->inode);
-	nfs_commitdata_release(calldata);
+	nfs_commit_free(data);
 }
 
 static const struct rpc_call_ops nfs_commit_direct_ops = {
@@ -570,7 +570,7 @@ static void nfs_direct_commit_schedule(struct nfs_direct_req *dreq)
 	data->args.fh = NFS_FH(data->inode);
 	data->args.offset = 0;
 	data->args.count = 0;
-	data->args.context = get_nfs_open_context(dreq->ctx);
+	data->args.context = dreq->ctx;
 	data->res.count = 0;
 	data->res.fattr = &data->fattr;
 	data->res.verf = &data->verf;
@@ -734,14 +734,14 @@ static ssize_t nfs_direct_write_schedule_segment(struct nfs_direct_req *dreq,
 					data->npages, 0, 0, data->pagevec, NULL);
 		up_read(&current->mm->mmap_sem);
 		if (result < 0) {
-			nfs_writedata_release(data);
+			nfs_writedata_free(data);
 			break;
 		}
 		if ((unsigned)result < data->npages) {
 			bytes = result * PAGE_SIZE;
 			if (bytes <= pgbase) {
 				nfs_direct_release_pages(data->pagevec, result);
-				nfs_writedata_release(data);
+				nfs_writedata_free(data);
 				break;
 			}
 			bytes -= pgbase;
@@ -756,7 +756,7 @@ static ssize_t nfs_direct_write_schedule_segment(struct nfs_direct_req *dreq,
 		data->inode = inode;
 		data->cred = msg.rpc_cred;
 		data->args.fh = NFS_FH(inode);
-		data->args.context = get_nfs_open_context(ctx);
+		data->args.context = ctx;
 		data->args.offset = pos;
 		data->args.pgbase = pgbase;
 		data->args.pages = data->pagevec;
diff --git a/fs/nfs/read.c b/fs/nfs/read.c
index 73ea5e8d66c..12c9e66d3f1 100644
--- a/fs/nfs/read.c
+++ b/fs/nfs/read.c
@@ -60,17 +60,15 @@ struct nfs_read_data *nfs_readdata_alloc(unsigned int pagecount)
 	return p;
 }
 
-static void nfs_readdata_free(struct nfs_read_data *p)
+void nfs_readdata_free(struct nfs_read_data *p)
 {
 	if (p && (p->pagevec != &p->page_array[0]))
 		kfree(p->pagevec);
 	mempool_free(p, nfs_rdata_mempool);
 }
 
-void nfs_readdata_release(void *data)
+static void nfs_readdata_release(struct nfs_read_data *rdata)
 {
-	struct nfs_read_data *rdata = data;
-
 	put_nfs_open_context(rdata->args.context);
 	nfs_readdata_free(rdata);
 }
diff --git a/fs/nfs/write.c b/fs/nfs/write.c
index 0a0a2ff767c..a34fae21fe1 100644
--- a/fs/nfs/write.c
+++ b/fs/nfs/write.c
@@ -87,17 +87,15 @@ struct nfs_write_data *nfs_writedata_alloc(unsigned int pagecount)
 	return p;
 }
 
-static void nfs_writedata_free(struct nfs_write_data *p)
+void nfs_writedata_free(struct nfs_write_data *p)
 {
 	if (p && (p->pagevec != &p->page_array[0]))
 		kfree(p->pagevec);
 	mempool_free(p, nfs_wdata_mempool);
 }
 
-void nfs_writedata_release(void *data)
+static void nfs_writedata_release(struct nfs_write_data *wdata)
 {
-	struct nfs_write_data *wdata = data;
-
 	put_nfs_open_context(wdata->args.context);
 	nfs_writedata_free(wdata);
 }
diff --git a/include/linux/nfs_fs.h b/include/linux/nfs_fs.h
index fdffb413b19..f6b90240dd4 100644
--- a/include/linux/nfs_fs.h
+++ b/include/linux/nfs_fs.h
@@ -473,7 +473,6 @@ extern int  nfs_writepages(struct address_space *, struct writeback_control *);
 extern int  nfs_flush_incompatible(struct file *file, struct page *page);
 extern int  nfs_updatepage(struct file *, struct page *, unsigned int, unsigned int);
 extern int nfs_writeback_done(struct rpc_task *, struct nfs_write_data *);
-extern void nfs_writedata_release(void *);
 
 /*
  * Try to write back everything synchronously (but check the
@@ -488,7 +487,6 @@ extern int nfs_wb_page_cancel(struct inode *inode, struct page* page);
 extern int  nfs_commit_inode(struct inode *, int);
 extern struct nfs_write_data *nfs_commitdata_alloc(void);
 extern void nfs_commit_free(struct nfs_write_data *wdata);
-extern void nfs_commitdata_release(void *wdata);
 #else
 static inline int
 nfs_commit_inode(struct inode *inode, int how)
@@ -507,6 +505,7 @@ nfs_have_writebacks(struct inode *inode)
  * Allocate nfs_write_data structures
  */
 extern struct nfs_write_data *nfs_writedata_alloc(unsigned int npages);
+extern void nfs_writedata_free(struct nfs_write_data *);
 
 /*
  * linux/fs/nfs/read.c
@@ -515,7 +514,6 @@ extern int  nfs_readpage(struct file *, struct page *);
 extern int  nfs_readpages(struct file *, struct address_space *,
 		struct list_head *, unsigned);
 extern int  nfs_readpage_result(struct rpc_task *, struct nfs_read_data *);
-extern void nfs_readdata_release(void *data);
 extern int  nfs_readpage_async(struct nfs_open_context *, struct inode *,
 			       struct page *);
 
@@ -523,6 +521,7 @@ extern int  nfs_readpage_async(struct nfs_open_context *, struct inode *,
  * Allocate nfs_read_data structures
  */
 extern struct nfs_read_data *nfs_readdata_alloc(unsigned int npages);
+extern void nfs_readdata_free(struct nfs_read_data *);
 
 /*
  * linux/fs/nfs3proc.c
-- 
GitLab


From 39cbb602b543e477df71dca84b5b2e36f8bd29fc Mon Sep 17 00:00:00 2001
From: "Alan D. Brunelle" <alan.brunelle@hp.com>
Date: Fri, 7 Aug 2009 12:01:08 -0400
Subject: [PATCH 0798/1153] Remove double removal of blktrace directory

commit fd51d251e4cdb21f68e9dbc4336514d64a105a79
Author: Stefan Raspl <raspl@linux.vnet.ibm.com>
Date:   Tue May 19 09:59:08 2009 +0200

    blktrace: remove debugfs entries on bad path

added in an explicit invocation of debugfs_remove for bt->dir, in
blk_remove_buf_file_callback we are also getting the directory removed. On
occasion I am seeing memory corruption that I have bisected down to
this commit. [The testing involves a (long) series of I/O benchmarks
with blktrace invoked around the actual runs.] I believe that this
committed patch is correct, but the problem actually lies in the code
in blk_remove_buf_file_callback.

With this patch I am able to consistently get complete runs whereas
previously I could not get a single run to complete.

The first part of the patch simply moves the debugfs_remove below the
relay_close: the relay_close call will remove files under bt->dir, and
so we should not remove the directory until all the files we created
have been removed. (Note: This is not sufficient to fix the problem -
the file system code has ref counts on the directoy, so our invocation
does not cause the directory to actually be removed. Nonetheless, we
should not rely upon that feature.)

Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 kernel/trace/blktrace.c | 12 +-----------
 1 file changed, 1 insertion(+), 11 deletions(-)

diff --git a/kernel/trace/blktrace.c b/kernel/trace/blktrace.c
index 1090b0aed9b..7a34cb563fe 100644
--- a/kernel/trace/blktrace.c
+++ b/kernel/trace/blktrace.c
@@ -267,8 +267,8 @@ static void blk_trace_free(struct blk_trace *bt)
 {
 	debugfs_remove(bt->msg_file);
 	debugfs_remove(bt->dropped_file);
-	debugfs_remove(bt->dir);
 	relay_close(bt->rchan);
+	debugfs_remove(bt->dir);
 	free_percpu(bt->sequence);
 	free_percpu(bt->msg_data);
 	kfree(bt);
@@ -378,18 +378,8 @@ static int blk_subbuf_start_callback(struct rchan_buf *buf, void *subbuf,
 
 static int blk_remove_buf_file_callback(struct dentry *dentry)
 {
-	struct dentry *parent = dentry->d_parent;
 	debugfs_remove(dentry);
 
-	/*
-	* this will fail for all but the last file, but that is ok. what we
-	* care about is the top level buts->name directory going away, when
-	* the last trace file is gone. Then we don't have to rmdir() that
-	* manually on trace stop, so it nicely solves the issue with
-	* force killing of running traces.
-	*/
-
-	debugfs_remove(parent);
 	return 0;
 }
 
-- 
GitLab


From 51d5668cb2e3fd1827a55184e48606fff054c5be Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Thu, 13 Aug 2009 09:54:02 +1000
Subject: [PATCH 0799/1153] md: never advance 'events' counter by more than 1.

When assembling arrays, md allows two devices to have different event
counts as long as the difference is only '1'.  This is to cope with
a system failure between updating the metadata on two difference
devices.

However there are currently times when we update the event count by
2.  This was done to keep the event count even when the array is clean
and odd when it is dirty, which allows us to avoid writing common
update to spare devices and so allow those spares to go to sleep.

This is bad for the above reason.  So change it to never increase by
two.  This means that the alignment between 'odd/even' and
'clean/dirty' might take a little longer to attain, but that is only a
small cost.  The spares will get a few more updates but that will
still be spared (;-) most updates and can still go to sleep.

Prior to this patch there was a small chance that after a crash an
array would fail to assemble due to the overly large event count
mismatch.

Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/md.c | 13 +++++--------
 1 file changed, 5 insertions(+), 8 deletions(-)

diff --git a/drivers/md/md.c b/drivers/md/md.c
index 5614500092e..d18805fea11 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -1975,17 +1975,14 @@ repeat:
 		/* otherwise we have to go forward and ... */
 		mddev->events ++;
 		if (!mddev->in_sync || mddev->recovery_cp != MaxSector) { /* not clean */
-			/* .. if the array isn't clean, insist on an odd 'events' */
-			if ((mddev->events&1)==0) {
-				mddev->events++;
+			/* .. if the array isn't clean, an 'even' event must also go
+			 * to spares. */
+			if ((mddev->events&1)==0)
 				nospares = 0;
-			}
 		} else {
-			/* otherwise insist on an even 'events' (for clean states) */
-			if ((mddev->events&1)) {
-				mddev->events++;
+			/* otherwise an 'odd' event must go to spares */
+			if ((mddev->events&1))
 				nospares = 0;
-			}
 		}
 	}
 
-- 
GitLab


From 67ac6011db5d2b0c853d573ff474b25c85dfb644 Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Thu, 13 Aug 2009 10:06:24 +1000
Subject: [PATCH 0800/1153] md/raid5: allow new reshape modes to be restarted
 in the middle.

md/raid5 doesn't allow a reshape to restart if it involves writing
over the same part of disk that it would be reading from.
This happens at the beginning of a reshape that increases the number
of devices, at the end of a reshape that decreases the number of
devices, and continuously for a reshape that does not change the
number of devices.

The current code is correct for the "increase number of devices"
case as the critical section at the start is handled by userspace
performing a backup.

It does not work for reducing the number of devices, or the
no-change case.
For 'reducing', we need to invert the test.  For no-change we cannot
really be sure things will be safe, so simply require the array
to be read-only, which is how the user-space code which carefully
starts such arrays works.

Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/raid5.c | 21 ++++++++++++++++++++-
 1 file changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index 2b521ee67df..b8a22a2205c 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -4509,7 +4509,26 @@ static int run(mddev_t *mddev)
 			   (old_disks-max_degraded));
 		/* here_old is the first stripe that we might need to read
 		 * from */
-		if (here_new >= here_old) {
+		if (mddev->delta_disks == 0) {
+			/* We cannot be sure it is safe to start an in-place
+			 * reshape.  It is only safe if user-space if monitoring
+			 * and taking constant backups.
+			 * mdadm always starts a situation like this in
+			 * readonly mode so it can take control before
+			 * allowing any writes.  So just check for that.
+			 */
+			if ((here_new * mddev->new_chunk_sectors != 
+			     here_old * mddev->chunk_sectors) ||
+			    mddev->ro == 0) {
+				printk(KERN_ERR "raid5: in-place reshape must be started"
+				       " in read-only mode - aborting\n");
+				return -EINVAL;
+			}
+		} else if (mddev->delta_disks < 0
+		    ? (here_new * mddev->new_chunk_sectors <=
+		       here_old * mddev->chunk_sectors)
+		    : (here_new * mddev->new_chunk_sectors >=
+		       here_old * mddev->chunk_sectors)) {
 			/* Reading from the same stripe as writing to - bad */
 			printk(KERN_ERR "raid5: reshape_position too early for "
 			       "auto-recovery - aborting.\n");
-- 
GitLab


From a639755cf885e437b2fe4168d35157fa90d530ab Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Thu, 13 Aug 2009 10:13:00 +1000
Subject: [PATCH 0801/1153] md/raid5: make sure a reshape restarts at the
 correct address.

This "if" don't allow for the possibility that the number of devices
doesn't change, and so sector_nr isn't set correctly in that case.
So change '>' to '>='.

Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/raid5.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index b8a22a2205c..94a74cb5ccc 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -3785,7 +3785,7 @@ static sector_t reshape_request(mddev_t *mddev, sector_t sector_nr, int *skipped
 		    conf->reshape_progress < raid5_size(mddev, 0, 0)) {
 			sector_nr = raid5_size(mddev, 0, 0)
 				- conf->reshape_progress;
-		} else if (mddev->delta_disks > 0 &&
+		} else if (mddev->delta_disks >= 0 &&
 			   conf->reshape_progress > 0)
 			sector_nr = conf->reshape_progress;
 		sector_div(sector_nr, new_data_disks);
-- 
GitLab


From 9799218ae36910af50f002a5db1802d576fffb43 Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Wed, 12 Aug 2009 17:37:52 -0700
Subject: [PATCH 0802/1153] Revert "libertas: Read buffer overflow"

This reverts commit 57921c312e8cef72ba35a4cfe870b376da0b1b87.

On request from John Linville:

	It has been shown to create a new problem.  There is work
	towards a solution to that one, but it isn't a simple
	clean-up.

Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/wireless/libertas/assoc.c | 18 ++++++++++--------
 1 file changed, 10 insertions(+), 8 deletions(-)

diff --git a/drivers/net/wireless/libertas/assoc.c b/drivers/net/wireless/libertas/assoc.c
index d6997371c27..b9b37411903 100644
--- a/drivers/net/wireless/libertas/assoc.c
+++ b/drivers/net/wireless/libertas/assoc.c
@@ -1,7 +1,6 @@
 /* Copyright (C) 2006, Red Hat, Inc. */
 
 #include <linux/types.h>
-#include <linux/kernel.h>
 #include <linux/etherdevice.h>
 #include <linux/ieee80211.h>
 #include <linux/if_arp.h>
@@ -44,21 +43,21 @@ static int get_common_rates(struct lbs_private *priv,
 	u16 *rates_size)
 {
 	u8 *card_rates = lbs_bg_rates;
+	size_t num_card_rates = sizeof(lbs_bg_rates);
 	int ret = 0, i, j;
-	u8 tmp[(ARRAY_SIZE(lbs_bg_rates) - 1) * (*rates_size - 1)];
+	u8 tmp[30];
 	size_t tmp_size = 0;
 
 	/* For each rate in card_rates that exists in rate1, copy to tmp */
-	for (i = 0; i < ARRAY_SIZE(lbs_bg_rates) && card_rates[i]; i++) {
-		for (j = 0; j < *rates_size && rates[j]; j++) {
+	for (i = 0; card_rates[i] && (i < num_card_rates); i++) {
+		for (j = 0; rates[j] && (j < *rates_size); j++) {
 			if (rates[j] == card_rates[i])
 				tmp[tmp_size++] = card_rates[i];
 		}
 	}
 
 	lbs_deb_hex(LBS_DEB_JOIN, "AP rates    ", rates, *rates_size);
-	lbs_deb_hex(LBS_DEB_JOIN, "card rates  ", card_rates,
-			ARRAY_SIZE(lbs_bg_rates));
+	lbs_deb_hex(LBS_DEB_JOIN, "card rates  ", card_rates, num_card_rates);
 	lbs_deb_hex(LBS_DEB_JOIN, "common rates", tmp, tmp_size);
 	lbs_deb_join("TX data rate 0x%02x\n", priv->cur_rate);
 
@@ -70,7 +69,10 @@ static int get_common_rates(struct lbs_private *priv,
 		lbs_pr_alert("Previously set fixed data rate %#x isn't "
 		       "compatible with the network.\n", priv->cur_rate);
 		ret = -1;
+		goto done;
 	}
+	ret = 0;
+
 done:
 	memset(rates, 0, *rates_size);
 	*rates_size = min_t(int, tmp_size, *rates_size);
@@ -320,7 +322,7 @@ static int lbs_associate(struct lbs_private *priv,
 	rates = (struct mrvl_ie_rates_param_set *) pos;
 	rates->header.type = cpu_to_le16(TLV_TYPE_RATES);
 	memcpy(&rates->rates, &bss->rates, MAX_RATES);
-	tmplen = min_t(u16, ARRAY_SIZE(rates->rates), MAX_RATES);
+	tmplen = MAX_RATES;
 	if (get_common_rates(priv, rates->rates, &tmplen)) {
 		ret = -1;
 		goto done;
@@ -596,7 +598,7 @@ static int lbs_adhoc_join(struct lbs_private *priv,
 
 	/* Copy Data rates from the rates recorded in scan response */
 	memset(cmd.bss.rates, 0, sizeof(cmd.bss.rates));
-	ratesize = min_t(u16, ARRAY_SIZE(cmd.bss.rates), MAX_RATES);
+	ratesize = min_t(u16, sizeof(cmd.bss.rates), MAX_RATES);
 	memcpy(cmd.bss.rates, bss->rates, ratesize);
 	if (get_common_rates(priv, cmd.bss.rates, &ratesize)) {
 		lbs_deb_join("ADHOC_JOIN: get_common_rates returned error.\n");
-- 
GitLab


From 1a67dde0abba36421a1257d01ba9de2f6d1c160a Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Thu, 13 Aug 2009 10:41:49 +1000
Subject: [PATCH 0803/1153] md/raid5: Properly remove excess drives after
 shrinking a raid5/6

We were removing the drives, from the array, but not
removing symlinks from /sys/.... and not marking the device
as having been removed.

Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/raid5.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index 94a74cb5ccc..b8a2c5dc67b 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -5097,8 +5097,15 @@ static void raid5_finish_reshape(mddev_t *mddev)
 					mddev->degraded--;
 			for (d = conf->raid_disks ;
 			     d < conf->raid_disks - mddev->delta_disks;
-			     d++)
-				raid5_remove_disk(mddev, d);
+			     d++) {
+				mdk_rdev_t *rdev = conf->disks[d].rdev;
+				if (rdev && raid5_remove_disk(mddev, d) == 0) {
+					char nm[20];
+					sprintf(nm, "rd%d", rdev->raid_disk);
+					sysfs_remove_link(&mddev->kobj, nm);
+					rdev->raid_disk = -1;
+				}
+			}
 		}
 		mddev->layout = conf->algorithm;
 		mddev->chunk_sectors = conf->chunk_sectors;
-- 
GitLab


From 4d484a4a7a5126410eed5f8dd329a33f6eeed068 Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Thu, 13 Aug 2009 10:41:50 +1000
Subject: [PATCH 0804/1153] md: allow upper limit for resync/reshape to be set
 when array is read-only

Normally we only allow the upper limit for a reshape to be decreased
when the array not performing a sync/recovery/reshape, otherwise there
could be races.  But if an array is part-way through a reshape when it
is assembled the reshape is started immediately leaving no window
to set an upper bound.

If the array is started read-only, the reshape will be suspended until
the array becomes writable, so that provides a window during which it
is perfectly safe to reduce the upper limit of a reshape.

So: allow the upper limit (sync_max) to be reduced even if the reshape
thread is running, as long as the array is still read-only.

Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/md.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/md/md.c b/drivers/md/md.c
index d18805fea11..103f2d33fa8 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -3599,6 +3599,7 @@ max_sync_store(mddev_t *mddev, const char *buf, size_t len)
 		if (max < mddev->resync_min)
 			return -EINVAL;
 		if (max < mddev->resync_max &&
+		    mddev->ro == 0 &&
 		    test_bit(MD_RECOVERY_RUNNING, &mddev->recovery))
 			return -EBUSY;
 
-- 
GitLab


From ba9a633787eed1e90d587282642580ad3d44f7fd Mon Sep 17 00:00:00 2001
From: Magnus Damm <damm@igel.co.jp>
Date: Wed, 22 Jul 2009 15:14:29 +0000
Subject: [PATCH 0805/1153] sh: convert processor device setup functions to
 arch_initcall()

Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().

This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().

A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
---
 arch/sh/kernel/cpu/sh2/setup-sh7619.c  | 2 +-
 arch/sh/kernel/cpu/sh2a/setup-mxg.c    | 2 +-
 arch/sh/kernel/cpu/sh2a/setup-sh7201.c | 2 +-
 arch/sh/kernel/cpu/sh2a/setup-sh7203.c | 2 +-
 arch/sh/kernel/cpu/sh2a/setup-sh7206.c | 2 +-
 arch/sh/kernel/cpu/sh3/setup-sh7705.c  | 2 +-
 arch/sh/kernel/cpu/sh3/setup-sh770x.c  | 2 +-
 arch/sh/kernel/cpu/sh3/setup-sh7710.c  | 2 +-
 arch/sh/kernel/cpu/sh3/setup-sh7720.c  | 2 +-
 arch/sh/kernel/cpu/sh4/setup-sh4-202.c | 2 +-
 arch/sh/kernel/cpu/sh4/setup-sh7750.c  | 2 +-
 arch/sh/kernel/cpu/sh4/setup-sh7760.c  | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-sh7343.c | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-sh7366.c | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-sh7722.c | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-sh7723.c | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-sh7724.c | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-sh7763.c | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-sh7770.c | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-sh7780.c | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-sh7785.c | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-sh7786.c | 2 +-
 arch/sh/kernel/cpu/sh4a/setup-shx3.c   | 2 +-
 arch/sh/kernel/cpu/sh5/setup-sh5.c     | 2 +-
 24 files changed, 24 insertions(+), 24 deletions(-)

diff --git a/arch/sh/kernel/cpu/sh2/setup-sh7619.c b/arch/sh/kernel/cpu/sh2/setup-sh7619.c
index 13798733f2d..8555c05e866 100644
--- a/arch/sh/kernel/cpu/sh2/setup-sh7619.c
+++ b/arch/sh/kernel/cpu/sh2/setup-sh7619.c
@@ -187,7 +187,7 @@ static int __init sh7619_devices_setup(void)
 	return platform_add_devices(sh7619_devices,
 				    ARRAY_SIZE(sh7619_devices));
 }
-__initcall(sh7619_devices_setup);
+arch_initcall(sh7619_devices_setup);
 
 void __init plat_irq_setup(void)
 {
diff --git a/arch/sh/kernel/cpu/sh2a/setup-mxg.c b/arch/sh/kernel/cpu/sh2a/setup-mxg.c
index 869c2da4820..b6737644531 100644
--- a/arch/sh/kernel/cpu/sh2a/setup-mxg.c
+++ b/arch/sh/kernel/cpu/sh2a/setup-mxg.c
@@ -238,7 +238,7 @@ static int __init mxg_devices_setup(void)
 	return platform_add_devices(mxg_devices,
 				    ARRAY_SIZE(mxg_devices));
 }
-__initcall(mxg_devices_setup);
+arch_initcall(mxg_devices_setup);
 
 void __init plat_irq_setup(void)
 {
diff --git a/arch/sh/kernel/cpu/sh2a/setup-sh7201.c b/arch/sh/kernel/cpu/sh2a/setup-sh7201.c
index d8febe12806..fbde5b75deb 100644
--- a/arch/sh/kernel/cpu/sh2a/setup-sh7201.c
+++ b/arch/sh/kernel/cpu/sh2a/setup-sh7201.c
@@ -357,7 +357,7 @@ static int __init sh7201_devices_setup(void)
 	return platform_add_devices(sh7201_devices,
 				    ARRAY_SIZE(sh7201_devices));
 }
-__initcall(sh7201_devices_setup);
+arch_initcall(sh7201_devices_setup);
 
 void __init plat_irq_setup(void)
 {
diff --git a/arch/sh/kernel/cpu/sh2a/setup-sh7203.c b/arch/sh/kernel/cpu/sh2a/setup-sh7203.c
index 62e3039d239..d3fd536c9a8 100644
--- a/arch/sh/kernel/cpu/sh2a/setup-sh7203.c
+++ b/arch/sh/kernel/cpu/sh2a/setup-sh7203.c
@@ -367,7 +367,7 @@ static int __init sh7203_devices_setup(void)
 	return platform_add_devices(sh7203_devices,
 				    ARRAY_SIZE(sh7203_devices));
 }
-__initcall(sh7203_devices_setup);
+arch_initcall(sh7203_devices_setup);
 
 void __init plat_irq_setup(void)
 {
diff --git a/arch/sh/kernel/cpu/sh2a/setup-sh7206.c b/arch/sh/kernel/cpu/sh2a/setup-sh7206.c
index 3e6f3d7a58b..a9ccc5e8d9e 100644
--- a/arch/sh/kernel/cpu/sh2a/setup-sh7206.c
+++ b/arch/sh/kernel/cpu/sh2a/setup-sh7206.c
@@ -338,7 +338,7 @@ static int __init sh7206_devices_setup(void)
 	return platform_add_devices(sh7206_devices,
 				    ARRAY_SIZE(sh7206_devices));
 }
-__initcall(sh7206_devices_setup);
+arch_initcall(sh7206_devices_setup);
 
 void __init plat_irq_setup(void)
 {
diff --git a/arch/sh/kernel/cpu/sh3/setup-sh7705.c b/arch/sh/kernel/cpu/sh3/setup-sh7705.c
index 88f742fed9e..c2310598387 100644
--- a/arch/sh/kernel/cpu/sh3/setup-sh7705.c
+++ b/arch/sh/kernel/cpu/sh3/setup-sh7705.c
@@ -222,7 +222,7 @@ static int __init sh7705_devices_setup(void)
 	return platform_add_devices(sh7705_devices,
 				    ARRAY_SIZE(sh7705_devices));
 }
-__initcall(sh7705_devices_setup);
+arch_initcall(sh7705_devices_setup);
 
 static struct platform_device *sh7705_early_devices[] __initdata = {
 	&tmu0_device,
diff --git a/arch/sh/kernel/cpu/sh3/setup-sh770x.c b/arch/sh/kernel/cpu/sh3/setup-sh770x.c
index c5630679858..347ab35d069 100644
--- a/arch/sh/kernel/cpu/sh3/setup-sh770x.c
+++ b/arch/sh/kernel/cpu/sh3/setup-sh770x.c
@@ -250,7 +250,7 @@ static int __init sh770x_devices_setup(void)
 	return platform_add_devices(sh770x_devices,
 		ARRAY_SIZE(sh770x_devices));
 }
-__initcall(sh770x_devices_setup);
+arch_initcall(sh770x_devices_setup);
 
 static struct platform_device *sh770x_early_devices[] __initdata = {
 	&tmu0_device,
diff --git a/arch/sh/kernel/cpu/sh3/setup-sh7710.c b/arch/sh/kernel/cpu/sh3/setup-sh7710.c
index efa76c8148f..717e90ae109 100644
--- a/arch/sh/kernel/cpu/sh3/setup-sh7710.c
+++ b/arch/sh/kernel/cpu/sh3/setup-sh7710.c
@@ -226,7 +226,7 @@ static int __init sh7710_devices_setup(void)
 	return platform_add_devices(sh7710_devices,
 				    ARRAY_SIZE(sh7710_devices));
 }
-__initcall(sh7710_devices_setup);
+arch_initcall(sh7710_devices_setup);
 
 static struct platform_device *sh7710_early_devices[] __initdata = {
 	&tmu0_device,
diff --git a/arch/sh/kernel/cpu/sh3/setup-sh7720.c b/arch/sh/kernel/cpu/sh3/setup-sh7720.c
index 5b2107798ed..74d8baaf8e9 100644
--- a/arch/sh/kernel/cpu/sh3/setup-sh7720.c
+++ b/arch/sh/kernel/cpu/sh3/setup-sh7720.c
@@ -388,7 +388,7 @@ static int __init sh7720_devices_setup(void)
 	return platform_add_devices(sh7720_devices,
 				    ARRAY_SIZE(sh7720_devices));
 }
-__initcall(sh7720_devices_setup);
+arch_initcall(sh7720_devices_setup);
 
 static struct platform_device *sh7720_early_devices[] __initdata = {
 	&cmt0_device,
diff --git a/arch/sh/kernel/cpu/sh4/setup-sh4-202.c b/arch/sh/kernel/cpu/sh4/setup-sh4-202.c
index 6d088d12359..de4827df19a 100644
--- a/arch/sh/kernel/cpu/sh4/setup-sh4-202.c
+++ b/arch/sh/kernel/cpu/sh4/setup-sh4-202.c
@@ -138,7 +138,7 @@ static int __init sh4202_devices_setup(void)
 	return platform_add_devices(sh4202_devices,
 				    ARRAY_SIZE(sh4202_devices));
 }
-__initcall(sh4202_devices_setup);
+arch_initcall(sh4202_devices_setup);
 
 static struct platform_device *sh4202_early_devices[] __initdata = {
 	&tmu0_device,
diff --git a/arch/sh/kernel/cpu/sh4/setup-sh7750.c b/arch/sh/kernel/cpu/sh4/setup-sh7750.c
index 851672d15cf..1b8b122e8f3 100644
--- a/arch/sh/kernel/cpu/sh4/setup-sh7750.c
+++ b/arch/sh/kernel/cpu/sh4/setup-sh7750.c
@@ -239,7 +239,7 @@ static int __init sh7750_devices_setup(void)
 	return platform_add_devices(sh7750_devices,
 				    ARRAY_SIZE(sh7750_devices));
 }
-__initcall(sh7750_devices_setup);
+arch_initcall(sh7750_devices_setup);
 
 static struct platform_device *sh7750_early_devices[] __initdata = {
 	&tmu0_device,
diff --git a/arch/sh/kernel/cpu/sh4/setup-sh7760.c b/arch/sh/kernel/cpu/sh4/setup-sh7760.c
index 5b822519bd9..7fbb7be9284 100644
--- a/arch/sh/kernel/cpu/sh4/setup-sh7760.c
+++ b/arch/sh/kernel/cpu/sh4/setup-sh7760.c
@@ -265,7 +265,7 @@ static int __init sh7760_devices_setup(void)
 	return platform_add_devices(sh7760_devices,
 				    ARRAY_SIZE(sh7760_devices));
 }
-__initcall(sh7760_devices_setup);
+arch_initcall(sh7760_devices_setup);
 
 static struct platform_device *sh7760_early_devices[] __initdata = {
 	&tmu0_device,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7343.c b/arch/sh/kernel/cpu/sh4a/setup-sh7343.c
index 6307e087c86..ac4d5672ec1 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7343.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7343.c
@@ -325,7 +325,7 @@ static int __init sh7343_devices_setup(void)
 	return platform_add_devices(sh7343_devices,
 				    ARRAY_SIZE(sh7343_devices));
 }
-__initcall(sh7343_devices_setup);
+arch_initcall(sh7343_devices_setup);
 
 static struct platform_device *sh7343_early_devices[] __initdata = {
 	&cmt_device,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7366.c b/arch/sh/kernel/cpu/sh4a/setup-sh7366.c
index c18f7d09281..1a956b1becc 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7366.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7366.c
@@ -318,7 +318,7 @@ static int __init sh7366_devices_setup(void)
 	return platform_add_devices(sh7366_devices,
 				    ARRAY_SIZE(sh7366_devices));
 }
-__initcall(sh7366_devices_setup);
+arch_initcall(sh7366_devices_setup);
 
 static struct platform_device *sh7366_early_devices[] __initdata = {
 	&cmt_device,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7722.c b/arch/sh/kernel/cpu/sh4a/setup-sh7722.c
index ea524a2da3e..cda76ebf87c 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7722.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7722.c
@@ -359,7 +359,7 @@ static int __init sh7722_devices_setup(void)
 	return platform_add_devices(sh7722_devices,
 				    ARRAY_SIZE(sh7722_devices));
 }
-__initcall(sh7722_devices_setup);
+arch_initcall(sh7722_devices_setup);
 
 static struct platform_device *sh7722_early_devices[] __initdata = {
 	&cmt_device,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7723.c b/arch/sh/kernel/cpu/sh4a/setup-sh7723.c
index e1bb80b2a27..b45dace9539 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7723.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7723.c
@@ -473,7 +473,7 @@ static int __init sh7723_devices_setup(void)
 	return platform_add_devices(sh7723_devices,
 				    ARRAY_SIZE(sh7723_devices));
 }
-__initcall(sh7723_devices_setup);
+arch_initcall(sh7723_devices_setup);
 
 static struct platform_device *sh7723_early_devices[] __initdata = {
 	&cmt_device,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7724.c b/arch/sh/kernel/cpu/sh4a/setup-sh7724.c
index e5ac9eb11c6..a04edaab9a2 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7724.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7724.c
@@ -508,7 +508,7 @@ static int __init sh7724_devices_setup(void)
 	return platform_add_devices(sh7724_devices,
 				    ARRAY_SIZE(sh7724_devices));
 }
-device_initcall(sh7724_devices_setup);
+arch_initcall(sh7724_devices_setup);
 
 static struct platform_device *sh7724_early_devices[] __initdata = {
 	&cmt_device,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7763.c b/arch/sh/kernel/cpu/sh4a/setup-sh7763.c
index f1e0c0d36da..4659fff6b84 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7763.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7763.c
@@ -314,7 +314,7 @@ static int __init sh7763_devices_setup(void)
 	return platform_add_devices(sh7763_devices,
 				    ARRAY_SIZE(sh7763_devices));
 }
-__initcall(sh7763_devices_setup);
+arch_initcall(sh7763_devices_setup);
 
 static struct platform_device *sh7763_early_devices[] __initdata = {
 	&tmu0_device,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7770.c b/arch/sh/kernel/cpu/sh4a/setup-sh7770.c
index 1e86209db28..eead08d89d3 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7770.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7770.c
@@ -368,7 +368,7 @@ static int __init sh7770_devices_setup(void)
 	return platform_add_devices(sh7770_devices,
 				    ARRAY_SIZE(sh7770_devices));
 }
-__initcall(sh7770_devices_setup);
+arch_initcall(sh7770_devices_setup);
 
 static struct platform_device *sh7770_early_devices[] __initdata = {
 	&tmu0_device,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7780.c b/arch/sh/kernel/cpu/sh4a/setup-sh7780.c
index 715e05b431e..2c901f44695 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7780.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7780.c
@@ -256,7 +256,7 @@ static int __init sh7780_devices_setup(void)
 	return platform_add_devices(sh7780_devices,
 				    ARRAY_SIZE(sh7780_devices));
 }
-__initcall(sh7780_devices_setup);
+arch_initcall(sh7780_devices_setup);
 
 static struct platform_device *sh7780_early_devices[] __initdata = {
 	&tmu0_device,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7785.c b/arch/sh/kernel/cpu/sh4a/setup-sh7785.c
index af561402570..7f6c718b6c3 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7785.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7785.c
@@ -263,7 +263,7 @@ static int __init sh7785_devices_setup(void)
 	return platform_add_devices(sh7785_devices,
 				    ARRAY_SIZE(sh7785_devices));
 }
-__initcall(sh7785_devices_setup);
+arch_initcall(sh7785_devices_setup);
 
 static struct platform_device *sh7785_early_devices[] __initdata = {
 	&tmu0_device,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7786.c b/arch/sh/kernel/cpu/sh4a/setup-sh7786.c
index b70049470a0..0104a8ec536 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7786.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7786.c
@@ -547,7 +547,7 @@ static int __init sh7786_devices_setup(void)
 	return platform_add_devices(sh7786_devices,
 				    ARRAY_SIZE(sh7786_devices));
 }
-device_initcall(sh7786_devices_setup);
+arch_initcall(sh7786_devices_setup);
 
 void __init plat_early_device_setup(void)
 {
diff --git a/arch/sh/kernel/cpu/sh4a/setup-shx3.c b/arch/sh/kernel/cpu/sh4a/setup-shx3.c
index 53c65fd9cce..07f078961c7 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-shx3.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-shx3.c
@@ -256,7 +256,7 @@ static int __init shx3_devices_setup(void)
 	return platform_add_devices(shx3_devices,
 				    ARRAY_SIZE(shx3_devices));
 }
-__initcall(shx3_devices_setup);
+arch_initcall(shx3_devices_setup);
 
 void __init plat_early_device_setup(void)
 {
diff --git a/arch/sh/kernel/cpu/sh5/setup-sh5.c b/arch/sh/kernel/cpu/sh5/setup-sh5.c
index f5ff1ac57fc..6a0f82f7003 100644
--- a/arch/sh/kernel/cpu/sh5/setup-sh5.c
+++ b/arch/sh/kernel/cpu/sh5/setup-sh5.c
@@ -186,7 +186,7 @@ static int __init sh5_devices_setup(void)
 	return platform_add_devices(sh5_devices,
 				    ARRAY_SIZE(sh5_devices));
 }
-__initcall(sh5_devices_setup);
+arch_initcall(sh5_devices_setup);
 
 void __init plat_early_device_setup(void)
 {
-- 
GitLab


From ba3a17019181af5d6ab898760620c4e9916396c2 Mon Sep 17 00:00:00 2001
From: Magnus Damm <damm@igel.co.jp>
Date: Thu, 13 Aug 2009 11:39:02 +0900
Subject: [PATCH 0806/1153] sh: fix i2c init order on Migo-R V2

Convert the Migo-R board code to register devices at
arch_initcall() time instead of __initcall(). This fix
unbreaks migor_ts touch screen driver support.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
---
 arch/sh/boards/mach-migor/setup.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/sh/boards/mach-migor/setup.c b/arch/sh/boards/mach-migor/setup.c
index f70f4644deb..f9b2e4df35b 100644
--- a/arch/sh/boards/mach-migor/setup.c
+++ b/arch/sh/boards/mach-migor/setup.c
@@ -608,7 +608,7 @@ static int __init migor_devices_setup(void)
 
 	return platform_add_devices(migor_devices, ARRAY_SIZE(migor_devices));
 }
-__initcall(migor_devices_setup);
+arch_initcall(migor_devices_setup);
 
 /* Return the board specific boot mode pin configuration */
 static int migor_mode_pins(void)
-- 
GitLab


From dbefd606a3b3634799b625f4900336e61c89e868 Mon Sep 17 00:00:00 2001
From: Magnus Damm <damm@igel.co.jp>
Date: Fri, 7 Aug 2009 03:52:18 +0000
Subject: [PATCH 0807/1153] sh: fix i2c init order on ap325rxa V2

Convert the AP325RXA board code to register devices at
arch_initcall() time instead of device_initcall(). This
fix unbreaks pcf8563 RTC driver support.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
---
 arch/sh/boards/board-ap325rxa.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/sh/boards/board-ap325rxa.c b/arch/sh/boards/board-ap325rxa.c
index 7ffd1b4315b..b9c88cc519e 100644
--- a/arch/sh/boards/board-ap325rxa.c
+++ b/arch/sh/boards/board-ap325rxa.c
@@ -547,7 +547,7 @@ static int __init ap325rxa_devices_setup(void)
 	return platform_add_devices(ap325rxa_devices,
 				ARRAY_SIZE(ap325rxa_devices));
 }
-device_initcall(ap325rxa_devices_setup);
+arch_initcall(ap325rxa_devices_setup);
 
 /* Return the board specific boot mode pin configuration */
 static int ap325rxa_mode_pins(void)
-- 
GitLab


From 839d1624b9dcf31fdc02e47359043bb7bd71d6ca Mon Sep 17 00:00:00 2001
From: Francois Romieu <romieu@fr.zoreil.com>
Date: Wed, 12 Aug 2009 22:18:14 -0700
Subject: [PATCH 0808/1153] 8139cp: balance dma_map_single vs dma_unmap_single
 pair

The driver always:
1. allocate cp->rx_buf_sz + NET_IP_ALIGN
2. map cp->rx_buf_sz

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/8139cp.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/drivers/net/8139cp.c b/drivers/net/8139cp.c
index 50efde11ea6..d0dbbf39349 100644
--- a/drivers/net/8139cp.c
+++ b/drivers/net/8139cp.c
@@ -515,7 +515,7 @@ rx_status_loop:
 		dma_addr_t mapping;
 		struct sk_buff *skb, *new_skb;
 		struct cp_desc *desc;
-		unsigned buflen;
+		const unsigned buflen = cp->rx_buf_sz;
 
 		skb = cp->rx_skb[rx_tail];
 		BUG_ON(!skb);
@@ -549,8 +549,7 @@ rx_status_loop:
 			pr_debug("%s: rx slot %d status 0x%x len %d\n",
 			       dev->name, rx_tail, status, len);
 
-		buflen = cp->rx_buf_sz + NET_IP_ALIGN;
-		new_skb = netdev_alloc_skb(dev, buflen);
+		new_skb = netdev_alloc_skb(dev, buflen + NET_IP_ALIGN);
 		if (!new_skb) {
 			dev->stats.rx_dropped++;
 			goto rx_next;
-- 
GitLab


From 8f7a0dc51674ad0dd06155291b0aed60d655943c Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Wed, 12 Aug 2009 14:44:59 -0300
Subject: [PATCH 0809/1153] perf list: Fix large list output by using the pager

When /sys/kernel/debug is mounted the list can be imense, so
use the pager like the other tools.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20090812174459.GB3495@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-list.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/tools/perf/builtin-list.c b/tools/perf/builtin-list.c
index f990fa8a35c..d88c6961274 100644
--- a/tools/perf/builtin-list.c
+++ b/tools/perf/builtin-list.c
@@ -10,11 +10,12 @@
 
 #include "perf.h"
 
-#include "util/parse-options.h"
 #include "util/parse-events.h"
+#include "util/cache.h"
 
 int cmd_list(int argc __used, const char **argv __used, const char *prefix __used)
 {
+	setup_pager();
 	print_events();
 	return 0;
 }
-- 
GitLab


From 28402971d869e26271b25301011f667d3a5640c3 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Thu, 13 Aug 2009 10:13:22 +0200
Subject: [PATCH 0810/1153] perf_counter: Provide
 hw_perf_counter_setup_online() APIs

Provide weak aliases for hw_perf_counter_setup_online(). This is
used by the BTS patches (for v2.6.32), but it interacts with
fixes so propagate this upstream. (it has no effect as of yet)

Also export perf_counter_output() to architecture code.

Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 include/linux/perf_counter.h |  2 ++
 kernel/perf_counter.c        | 10 +++++++++-
 2 files changed, 11 insertions(+), 1 deletion(-)

diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h
index a9d823a93fe..2b36afe6ae0 100644
--- a/include/linux/perf_counter.h
+++ b/include/linux/perf_counter.h
@@ -694,6 +694,8 @@ struct perf_sample_data {
 
 extern int perf_counter_overflow(struct perf_counter *counter, int nmi,
 				 struct perf_sample_data *data);
+extern void perf_counter_output(struct perf_counter *counter, int nmi,
+				struct perf_sample_data *data);
 
 /*
  * Return 1 for a software counter, 0 for a hardware counter
diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index b0b20a07f39..e26d2fcfa32 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -88,6 +88,7 @@ void __weak hw_perf_disable(void)		{ barrier(); }
 void __weak hw_perf_enable(void)		{ barrier(); }
 
 void __weak hw_perf_counter_setup(int cpu)	{ barrier(); }
+void __weak hw_perf_counter_setup_online(int cpu)	{ barrier(); }
 
 int __weak
 hw_perf_group_sched_in(struct perf_counter *group_leader,
@@ -2630,7 +2631,7 @@ static u32 perf_counter_tid(struct perf_counter *counter, struct task_struct *p)
 	return task_pid_nr_ns(p, counter->ns);
 }
 
-static void perf_counter_output(struct perf_counter *counter, int nmi,
+void perf_counter_output(struct perf_counter *counter, int nmi,
 				struct perf_sample_data *data)
 {
 	int ret;
@@ -4592,6 +4593,11 @@ perf_cpu_notify(struct notifier_block *self, unsigned long action, void *hcpu)
 		perf_counter_init_cpu(cpu);
 		break;
 
+	case CPU_ONLINE:
+	case CPU_ONLINE_FROZEN:
+		hw_perf_counter_setup_online(cpu);
+		break;
+
 	case CPU_DOWN_PREPARE:
 	case CPU_DOWN_PREPARE_FROZEN:
 		perf_counter_exit_cpu(cpu);
@@ -4616,6 +4622,8 @@ void __init perf_counter_init(void)
 {
 	perf_cpu_notify(&perf_cpu_nb, (unsigned long)CPU_UP_PREPARE,
 			(void *)(long)smp_processor_id());
+	perf_cpu_notify(&perf_cpu_nb, (unsigned long)CPU_ONLINE,
+			(void *)(long)smp_processor_id());
 	register_cpu_notifier(&perf_cpu_nb);
 }
 
-- 
GitLab


From 3a9f131fb00b8ac5950a11ad1599e45edfb5ae44 Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Thu, 13 Aug 2009 10:27:18 +0200
Subject: [PATCH 0811/1153] perf tools: Add a per tracepoint counter attribute
 to get raw sample

Add a new flag field while opening a tracepoint perf counter:

	-e tracepoint_subsystem:tracepoint_name:flags

This is intended to be generic although for now it only supports the
r[e[c[o[r[d]]]]] flag:

	./perf record -e workqueue:workqueue_insertion:record
	./perf record -e workqueue:workqueue_insertion:r

will have the same effect: enabling the raw samples record for
the given tracepoint counter.

In the future, we may want to support further flags, separated
by commas.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1250152039-7284-1-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-record.c    |  2 +-
 tools/perf/util/parse-events.c | 10 ++++++++++
 2 files changed, 11 insertions(+), 1 deletion(-)

diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c
index de76008fbaa..78adc47da86 100644
--- a/tools/perf/builtin-record.c
+++ b/tools/perf/builtin-record.c
@@ -398,7 +398,7 @@ static void create_counter(int counter, int cpu, pid_t pid)
 				  PERF_FORMAT_TOTAL_TIME_RUNNING |
 				  PERF_FORMAT_ID;
 
-	attr->sample_type	= PERF_SAMPLE_IP | PERF_SAMPLE_TID;
+	attr->sample_type	|= PERF_SAMPLE_IP | PERF_SAMPLE_TID;
 
 	if (freq) {
 		attr->sample_type	|= PERF_SAMPLE_PERIOD;
diff --git a/tools/perf/util/parse-events.c b/tools/perf/util/parse-events.c
index 4858d83b3b6..04417840878 100644
--- a/tools/perf/util/parse-events.c
+++ b/tools/perf/util/parse-events.c
@@ -379,6 +379,7 @@ static int parse_tracepoint_event(const char **strp,
 				    struct perf_counter_attr *attr)
 {
 	const char *evt_name;
+	char *flags;
 	char sys_name[MAX_EVENT_LENGTH];
 	char id_buf[4];
 	int fd;
@@ -400,6 +401,15 @@ static int parse_tracepoint_event(const char **strp,
 	strncpy(sys_name, *strp, sys_length);
 	sys_name[sys_length] = '\0';
 	evt_name = evt_name + 1;
+
+	flags = strchr(evt_name, ':');
+	if (flags) {
+		*flags = '\0';
+		flags++;
+		if (!strncmp(flags, "record", strlen(flags)))
+			attr->sample_type |= PERF_SAMPLE_RAW;
+	}
+
 	evt_length = strlen(evt_name);
 	if (evt_length >= MAX_EVENT_LENGTH)
 		return 0;
-- 
GitLab


From daac07b2e6b77f1bd44104aa2f0593e5505f27d4 Mon Sep 17 00:00:00 2001
From: Frederic Weisbecker <fweisbec@gmail.com>
Date: Thu, 13 Aug 2009 10:27:19 +0200
Subject: [PATCH 0812/1153] perf tools: Add a general option to enable raw
 sample records

While we can enable the perf sample records per tracepoint
counter, we may also want to enable this option for every
tracepoint counters to open, so that we don't need to add a
:record flag for all of them.

Add the -R, --raw-samples options for this purpose.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1250152039-7284-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-record.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c
index 78adc47da86..3d051b9cf25 100644
--- a/tools/perf/builtin-record.c
+++ b/tools/perf/builtin-record.c
@@ -34,6 +34,7 @@ static int			output;
 static const char		*output_name			= "perf.data";
 static int			group				= 0;
 static unsigned int		realtime_prio			= 0;
+static int			raw_samples			= 0;
 static int			system_wide			= 0;
 static int			profile_cpu			= -1;
 static pid_t			target_pid			= -1;
@@ -418,6 +419,8 @@ static void create_counter(int counter, int cpu, pid_t pid)
 	if (call_graph)
 		attr->sample_type	|= PERF_SAMPLE_CALLCHAIN;
 
+	if (raw_samples)
+		attr->sample_type	|= PERF_SAMPLE_RAW;
 
 	attr->mmap		= track;
 	attr->comm		= track;
@@ -650,6 +653,8 @@ static const struct option options[] = {
 		    "record events on existing pid"),
 	OPT_INTEGER('r', "realtime", &realtime_prio,
 		    "collect data with this RT SCHED_FIFO priority"),
+	OPT_BOOLEAN('R', "raw-samples", &raw_samples,
+		    "collect raw sample records from all opened counters"),
 	OPT_BOOLEAN('a', "all-cpus", &system_wide,
 			    "system-wide collection from all CPUs"),
 	OPT_BOOLEAN('A', "append", &append_file,
-- 
GitLab


From 8fd101f20bdf771949a8f3a5a779877d09b2fb56 Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Wed, 12 Aug 2009 18:19:57 -0300
Subject: [PATCH 0813/1153] perf report: Don't show unresolved DSOs and symbols
 when -S/-d is used

We're interested in just those symbols/DSOs, so filter out the
unresolved ones.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20090812211957.GE3495@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-report.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index 23e1457f240..b53a60fc12d 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -1590,10 +1590,11 @@ process_sample_event(event_t *event, unsigned long offset, unsigned long head)
 	if (show & show_mask) {
 		struct symbol *sym = resolve_symbol(thread, &map, &dso, &ip);
 
-		if (dso_list && dso && dso->name && !strlist__has_entry(dso_list, dso->name))
+		if (dso_list && (!dso || !dso->name ||
+				 !strlist__has_entry(dso_list, dso->name)))
 			return 0;
 
-		if (sym_list && sym && !strlist__has_entry(sym_list, sym->name))
+		if (sym_list && (!sym || !strlist__has_entry(sym_list, sym->name)))
 			return 0;
 
 		if (hist_entry__add(thread, map, dso, sym, ip, chain, level, period)) {
-- 
GitLab


From bcfc2602e8541ac13b1def38e2591dca072cff7a Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <peterz@infradead.org>
Date: Thu, 13 Aug 2009 09:51:55 +0200
Subject: [PATCH 0814/1153] perf_counter: Fix swcounter context invariance

perf_swcounter_is_counting() uses a lock, which means we cannot
use swcounters from NMI or when holding that particular lock,
this is unintended.

The below removes the lock, this opens up race window, but not
worse than the swcounters already experience due to RCU
traversal of the context in perf_swcounter_ctx_event().

This also fixes the hard lockups while opening a lockdep
tracepoint counter.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
Cc: Corey J Ashford <cjashfor@us.ibm.com>
LKML-Reference: <1250149915.10001.66.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 44 ++++++++++++++++++-------------------------
 1 file changed, 18 insertions(+), 26 deletions(-)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index e26d2fcfa32..3dd4339589a 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -3444,40 +3444,32 @@ static void perf_swcounter_add(struct perf_counter *counter, u64 nr,
 
 static int perf_swcounter_is_counting(struct perf_counter *counter)
 {
-	struct perf_counter_context *ctx;
-	unsigned long flags;
-	int count;
-
+	/*
+	 * The counter is active, we're good!
+	 */
 	if (counter->state == PERF_COUNTER_STATE_ACTIVE)
 		return 1;
 
+	/*
+	 * The counter is off/error, not counting.
+	 */
 	if (counter->state != PERF_COUNTER_STATE_INACTIVE)
 		return 0;
 
 	/*
-	 * If the counter is inactive, it could be just because
-	 * its task is scheduled out, or because it's in a group
-	 * which could not go on the PMU.  We want to count in
-	 * the first case but not the second.  If the context is
-	 * currently active then an inactive software counter must
-	 * be the second case.  If it's not currently active then
-	 * we need to know whether the counter was active when the
-	 * context was last active, which we can determine by
-	 * comparing counter->tstamp_stopped with ctx->time.
-	 *
-	 * We are within an RCU read-side critical section,
-	 * which protects the existence of *ctx.
+	 * The counter is inactive, if the context is active
+	 * we're part of a group that didn't make it on the 'pmu',
+	 * not counting.
 	 */
-	ctx = counter->ctx;
-	spin_lock_irqsave(&ctx->lock, flags);
-	count = 1;
-	/* Re-check state now we have the lock */
-	if (counter->state < PERF_COUNTER_STATE_INACTIVE ||
-	    counter->ctx->is_active ||
-	    counter->tstamp_stopped < ctx->time)
-		count = 0;
-	spin_unlock_irqrestore(&ctx->lock, flags);
-	return count;
+	if (counter->ctx->is_active)
+		return 0;
+
+	/*
+	 * We're inactive and the context is too, this means the
+	 * task is scheduled out, we're counting events that happen
+	 * to us, like migration events.
+	 */
+	return 1;
 }
 
 static int perf_swcounter_match(struct perf_counter *counter,
-- 
GitLab


From 3dab77fb1bf89664bb1c9544607159dcab6f7d57 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Thu, 13 Aug 2009 11:47:53 +0200
Subject: [PATCH 0815/1153] perf: Rework/fix the whole read vs group stuff

Replace PERF_SAMPLE_GROUP with PERF_SAMPLE_READ and introduce
PERF_FORMAT_GROUP to deal with group reads in a more generic
way.

This allows you to get group reads out of read() as well.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey J Ashford <cjashfor@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
LKML-Reference: <20090813103655.117411814@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 include/linux/perf_counter.h |  47 ++++--
 kernel/perf_counter.c        | 274 ++++++++++++++++++++++++++---------
 2 files changed, 238 insertions(+), 83 deletions(-)

diff --git a/include/linux/perf_counter.h b/include/linux/perf_counter.h
index 2b36afe6ae0..b53f7006cc4 100644
--- a/include/linux/perf_counter.h
+++ b/include/linux/perf_counter.h
@@ -115,7 +115,7 @@ enum perf_counter_sample_format {
 	PERF_SAMPLE_TID				= 1U << 1,
 	PERF_SAMPLE_TIME			= 1U << 2,
 	PERF_SAMPLE_ADDR			= 1U << 3,
-	PERF_SAMPLE_GROUP			= 1U << 4,
+	PERF_SAMPLE_READ			= 1U << 4,
 	PERF_SAMPLE_CALLCHAIN			= 1U << 5,
 	PERF_SAMPLE_ID				= 1U << 6,
 	PERF_SAMPLE_CPU				= 1U << 7,
@@ -127,16 +127,32 @@ enum perf_counter_sample_format {
 };
 
 /*
- * Bits that can be set in attr.read_format to request that
- * reads on the counter should return the indicated quantities,
- * in increasing order of bit value, after the counter value.
+ * The format of the data returned by read() on a perf counter fd,
+ * as specified by attr.read_format:
+ *
+ * struct read_format {
+ * 	{ u64		value;
+ * 	  { u64		time_enabled; } && PERF_FORMAT_ENABLED
+ * 	  { u64		time_running; } && PERF_FORMAT_RUNNING
+ * 	  { u64		id;           } && PERF_FORMAT_ID
+ * 	} && !PERF_FORMAT_GROUP
+ *
+ * 	{ u64		nr;
+ * 	  { u64		time_enabled; } && PERF_FORMAT_ENABLED
+ * 	  { u64		time_running; } && PERF_FORMAT_RUNNING
+ * 	  { u64		value;
+ * 	    { u64	id;           } && PERF_FORMAT_ID
+ * 	  }		cntr[nr];
+ * 	} && PERF_FORMAT_GROUP
+ * };
  */
 enum perf_counter_read_format {
 	PERF_FORMAT_TOTAL_TIME_ENABLED		= 1U << 0,
 	PERF_FORMAT_TOTAL_TIME_RUNNING		= 1U << 1,
 	PERF_FORMAT_ID				= 1U << 2,
+	PERF_FORMAT_GROUP			= 1U << 3,
 
-	PERF_FORMAT_MAX = 1U << 3, 		/* non-ABI */
+	PERF_FORMAT_MAX = 1U << 4, 		/* non-ABI */
 };
 
 #define PERF_ATTR_SIZE_VER0	64	/* sizeof first published struct */
@@ -343,10 +359,8 @@ enum perf_event_type {
 	 * struct {
 	 * 	struct perf_event_header	header;
 	 * 	u32				pid, tid;
-	 * 	u64				value;
-	 * 	{ u64		time_enabled; 	} && PERF_FORMAT_ENABLED
-	 * 	{ u64		time_running; 	} && PERF_FORMAT_RUNNING
-	 * 	{ u64		parent_id;	} && PERF_FORMAT_ID
+	 *
+	 * 	struct read_format		values;
 	 * };
 	 */
 	PERF_EVENT_READ			= 8,
@@ -364,11 +378,22 @@ enum perf_event_type {
 	 *	{ u32			cpu, res; } && PERF_SAMPLE_CPU
 	 * 	{ u64			period;   } && PERF_SAMPLE_PERIOD
 	 *
-	 *	{ u64			nr;
-	 *	  { u64 id, val; }	cnt[nr];  } && PERF_SAMPLE_GROUP
+	 *	{ struct read_format	values;	  } && PERF_SAMPLE_READ
 	 *
 	 *	{ u64			nr,
 	 *	  u64			ips[nr];  } && PERF_SAMPLE_CALLCHAIN
+	 *
+	 * 	#
+	 * 	# The RAW record below is opaque data wrt the ABI
+	 * 	#
+	 * 	# That is, the ABI doesn't make any promises wrt to
+	 * 	# the stability of its content, it may vary depending
+	 * 	# on event, hardware, kernel version and phase of
+	 * 	# the moon.
+	 * 	#
+	 * 	# In other words, PERF_SAMPLE_RAW contents are not an ABI.
+	 * 	#
+	 *
 	 *	{ u32			size;
 	 *	  char                  data[size];}&& PERF_SAMPLE_RAW
 	 * };
diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 3dd4339589a..b8c6b97a20a 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -1692,7 +1692,32 @@ static int perf_release(struct inode *inode, struct file *file)
 	return 0;
 }
 
-static u64 perf_counter_read_tree(struct perf_counter *counter)
+static int perf_counter_read_size(struct perf_counter *counter)
+{
+	int entry = sizeof(u64); /* value */
+	int size = 0;
+	int nr = 1;
+
+	if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_ENABLED)
+		size += sizeof(u64);
+
+	if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_RUNNING)
+		size += sizeof(u64);
+
+	if (counter->attr.read_format & PERF_FORMAT_ID)
+		entry += sizeof(u64);
+
+	if (counter->attr.read_format & PERF_FORMAT_GROUP) {
+		nr += counter->group_leader->nr_siblings;
+		size += sizeof(u64);
+	}
+
+	size += entry * nr;
+
+	return size;
+}
+
+static u64 perf_counter_read_value(struct perf_counter *counter)
 {
 	struct perf_counter *child;
 	u64 total = 0;
@@ -1704,14 +1729,96 @@ static u64 perf_counter_read_tree(struct perf_counter *counter)
 	return total;
 }
 
+static int perf_counter_read_entry(struct perf_counter *counter,
+				   u64 read_format, char __user *buf)
+{
+	int n = 0, count = 0;
+	u64 values[2];
+
+	values[n++] = perf_counter_read_value(counter);
+	if (read_format & PERF_FORMAT_ID)
+		values[n++] = primary_counter_id(counter);
+
+	count = n * sizeof(u64);
+
+	if (copy_to_user(buf, values, count))
+		return -EFAULT;
+
+	return count;
+}
+
+static int perf_counter_read_group(struct perf_counter *counter,
+				   u64 read_format, char __user *buf)
+{
+	struct perf_counter *leader = counter->group_leader, *sub;
+	int n = 0, size = 0, err = -EFAULT;
+	u64 values[3];
+
+	values[n++] = 1 + leader->nr_siblings;
+	if (read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) {
+		values[n++] = leader->total_time_enabled +
+			atomic64_read(&leader->child_total_time_enabled);
+	}
+	if (read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) {
+		values[n++] = leader->total_time_running +
+			atomic64_read(&leader->child_total_time_running);
+	}
+
+	size = n * sizeof(u64);
+
+	if (copy_to_user(buf, values, size))
+		return -EFAULT;
+
+	err = perf_counter_read_entry(leader, read_format, buf + size);
+	if (err < 0)
+		return err;
+
+	size += err;
+
+	list_for_each_entry(sub, &leader->sibling_list, list_entry) {
+		err = perf_counter_read_entry(counter, read_format,
+				buf + size);
+		if (err < 0)
+			return err;
+
+		size += err;
+	}
+
+	return size;
+}
+
+static int perf_counter_read_one(struct perf_counter *counter,
+				 u64 read_format, char __user *buf)
+{
+	u64 values[4];
+	int n = 0;
+
+	values[n++] = perf_counter_read_value(counter);
+	if (read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) {
+		values[n++] = counter->total_time_enabled +
+			atomic64_read(&counter->child_total_time_enabled);
+	}
+	if (read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) {
+		values[n++] = counter->total_time_running +
+			atomic64_read(&counter->child_total_time_running);
+	}
+	if (read_format & PERF_FORMAT_ID)
+		values[n++] = primary_counter_id(counter);
+
+	if (copy_to_user(buf, values, n * sizeof(u64)))
+		return -EFAULT;
+
+	return n * sizeof(u64);
+}
+
 /*
  * Read the performance counter - simple non blocking version for now
  */
 static ssize_t
 perf_read_hw(struct perf_counter *counter, char __user *buf, size_t count)
 {
-	u64 values[4];
-	int n;
+	u64 read_format = counter->attr.read_format;
+	int ret;
 
 	/*
 	 * Return end-of-file for a read on a counter that is in
@@ -1721,28 +1828,18 @@ perf_read_hw(struct perf_counter *counter, char __user *buf, size_t count)
 	if (counter->state == PERF_COUNTER_STATE_ERROR)
 		return 0;
 
+	if (count < perf_counter_read_size(counter))
+		return -ENOSPC;
+
 	WARN_ON_ONCE(counter->ctx->parent_ctx);
 	mutex_lock(&counter->child_mutex);
-	values[0] = perf_counter_read_tree(counter);
-	n = 1;
-	if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_ENABLED)
-		values[n++] = counter->total_time_enabled +
-			atomic64_read(&counter->child_total_time_enabled);
-	if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_RUNNING)
-		values[n++] = counter->total_time_running +
-			atomic64_read(&counter->child_total_time_running);
-	if (counter->attr.read_format & PERF_FORMAT_ID)
-		values[n++] = primary_counter_id(counter);
+	if (read_format & PERF_FORMAT_GROUP)
+		ret = perf_counter_read_group(counter, read_format, buf);
+	else
+		ret = perf_counter_read_one(counter, read_format, buf);
 	mutex_unlock(&counter->child_mutex);
 
-	if (count < n * sizeof(u64))
-		return -EINVAL;
-	count = n * sizeof(u64);
-
-	if (copy_to_user(buf, values, count))
-		return -EFAULT;
-
-	return count;
+	return ret;
 }
 
 static ssize_t
@@ -2631,6 +2728,79 @@ static u32 perf_counter_tid(struct perf_counter *counter, struct task_struct *p)
 	return task_pid_nr_ns(p, counter->ns);
 }
 
+static void perf_output_read_one(struct perf_output_handle *handle,
+				 struct perf_counter *counter)
+{
+	u64 read_format = counter->attr.read_format;
+	u64 values[4];
+	int n = 0;
+
+	values[n++] = atomic64_read(&counter->count);
+	if (read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) {
+		values[n++] = counter->total_time_enabled +
+			atomic64_read(&counter->child_total_time_enabled);
+	}
+	if (read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) {
+		values[n++] = counter->total_time_running +
+			atomic64_read(&counter->child_total_time_running);
+	}
+	if (read_format & PERF_FORMAT_ID)
+		values[n++] = primary_counter_id(counter);
+
+	perf_output_copy(handle, values, n * sizeof(u64));
+}
+
+/*
+ * XXX PERF_FORMAT_GROUP vs inherited counters seems difficult.
+ */
+static void perf_output_read_group(struct perf_output_handle *handle,
+			    struct perf_counter *counter)
+{
+	struct perf_counter *leader = counter->group_leader, *sub;
+	u64 read_format = counter->attr.read_format;
+	u64 values[5];
+	int n = 0;
+
+	values[n++] = 1 + leader->nr_siblings;
+
+	if (read_format & PERF_FORMAT_TOTAL_TIME_ENABLED)
+		values[n++] = leader->total_time_enabled;
+
+	if (read_format & PERF_FORMAT_TOTAL_TIME_RUNNING)
+		values[n++] = leader->total_time_running;
+
+	if (leader != counter)
+		leader->pmu->read(leader);
+
+	values[n++] = atomic64_read(&leader->count);
+	if (read_format & PERF_FORMAT_ID)
+		values[n++] = primary_counter_id(leader);
+
+	perf_output_copy(handle, values, n * sizeof(u64));
+
+	list_for_each_entry(sub, &leader->sibling_list, list_entry) {
+		n = 0;
+
+		if (sub != counter)
+			sub->pmu->read(sub);
+
+		values[n++] = atomic64_read(&sub->count);
+		if (read_format & PERF_FORMAT_ID)
+			values[n++] = primary_counter_id(sub);
+
+		perf_output_copy(handle, values, n * sizeof(u64));
+	}
+}
+
+static void perf_output_read(struct perf_output_handle *handle,
+			     struct perf_counter *counter)
+{
+	if (counter->attr.read_format & PERF_FORMAT_GROUP)
+		perf_output_read_group(handle, counter);
+	else
+		perf_output_read_one(handle, counter);
+}
+
 void perf_counter_output(struct perf_counter *counter, int nmi,
 				struct perf_sample_data *data)
 {
@@ -2642,10 +2812,6 @@ void perf_counter_output(struct perf_counter *counter, int nmi,
 	struct {
 		u32 pid, tid;
 	} tid_entry;
-	struct {
-		u64 id;
-		u64 counter;
-	} group_entry;
 	struct perf_callchain_entry *callchain = NULL;
 	int callchain_size = 0;
 	u64 time;
@@ -2700,10 +2866,8 @@ void perf_counter_output(struct perf_counter *counter, int nmi,
 	if (sample_type & PERF_SAMPLE_PERIOD)
 		header.size += sizeof(u64);
 
-	if (sample_type & PERF_SAMPLE_GROUP) {
-		header.size += sizeof(u64) +
-			counter->nr_siblings * sizeof(group_entry);
-	}
+	if (sample_type & PERF_SAMPLE_READ)
+		header.size += perf_counter_read_size(counter);
 
 	if (sample_type & PERF_SAMPLE_CALLCHAIN) {
 		callchain = perf_callchain(data->regs);
@@ -2760,26 +2924,8 @@ void perf_counter_output(struct perf_counter *counter, int nmi,
 	if (sample_type & PERF_SAMPLE_PERIOD)
 		perf_output_put(&handle, data->period);
 
-	/*
-	 * XXX PERF_SAMPLE_GROUP vs inherited counters seems difficult.
-	 */
-	if (sample_type & PERF_SAMPLE_GROUP) {
-		struct perf_counter *leader, *sub;
-		u64 nr = counter->nr_siblings;
-
-		perf_output_put(&handle, nr);
-
-		leader = counter->group_leader;
-		list_for_each_entry(sub, &leader->sibling_list, list_entry) {
-			if (sub != counter)
-				sub->pmu->read(sub);
-
-			group_entry.id = primary_counter_id(sub);
-			group_entry.counter = atomic64_read(&sub->count);
-
-			perf_output_put(&handle, group_entry);
-		}
-	}
+	if (sample_type & PERF_SAMPLE_READ)
+		perf_output_read(&handle, counter);
 
 	if (sample_type & PERF_SAMPLE_CALLCHAIN) {
 		if (callchain)
@@ -2818,8 +2964,6 @@ struct perf_read_event {
 
 	u32				pid;
 	u32				tid;
-	u64				value;
-	u64				format[3];
 };
 
 static void
@@ -2831,34 +2975,20 @@ perf_counter_read_event(struct perf_counter *counter,
 		.header = {
 			.type = PERF_EVENT_READ,
 			.misc = 0,
-			.size = sizeof(event) - sizeof(event.format),
+			.size = sizeof(event) + perf_counter_read_size(counter),
 		},
 		.pid = perf_counter_pid(counter, task),
 		.tid = perf_counter_tid(counter, task),
-		.value = atomic64_read(&counter->count),
 	};
-	int ret, i = 0;
-
-	if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_ENABLED) {
-		event.header.size += sizeof(u64);
-		event.format[i++] = counter->total_time_enabled;
-	}
-
-	if (counter->attr.read_format & PERF_FORMAT_TOTAL_TIME_RUNNING) {
-		event.header.size += sizeof(u64);
-		event.format[i++] = counter->total_time_running;
-	}
-
-	if (counter->attr.read_format & PERF_FORMAT_ID) {
-		event.header.size += sizeof(u64);
-		event.format[i++] = primary_counter_id(counter);
-	}
+	int ret;
 
 	ret = perf_output_begin(&handle, counter, event.header.size, 0, 0);
 	if (ret)
 		return;
 
-	perf_output_copy(&handle, &event, event.header.size);
+	perf_output_put(&handle, event);
+	perf_output_read(&handle, counter);
+
 	perf_output_end(&handle);
 }
 
@@ -3921,9 +4051,9 @@ perf_counter_alloc(struct perf_counter_attr *attr,
 	atomic64_set(&hwc->period_left, hwc->sample_period);
 
 	/*
-	 * we currently do not support PERF_SAMPLE_GROUP on inherited counters
+	 * we currently do not support PERF_FORMAT_GROUP on inherited counters
 	 */
-	if (attr->inherit && (attr->sample_type & PERF_SAMPLE_GROUP))
+	if (attr->inherit && (attr->read_format & PERF_FORMAT_GROUP))
 		goto done;
 
 	switch (attr->type) {
-- 
GitLab


From 970892a9031a5dc7217bd394fb9d89fa75a4a7bc Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Thu, 13 Aug 2009 11:47:54 +0200
Subject: [PATCH 0816/1153] perf_counter: Fix an ipi-deadlock

perf_pending_counter() is called from IRQ context and will call
perf_counter_disable(), however perf_counter_disable() uses
smp_call_function_single() which doesn't fancy being used with
IRQs disabled due to IPI deadlocks.

Fix this by making it use the local __perf_counter_disable()
call and teaching the counter_sched_out() code about pending
disables as well.

This should cover the case where a counter migrates before the
pending queue gets processed.

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey J Ashford <cjashfor@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
LKML-Reference: <20090813103655.244097721@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index b8c6b97a20a..3f841beefc7 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -307,6 +307,10 @@ counter_sched_out(struct perf_counter *counter,
 		return;
 
 	counter->state = PERF_COUNTER_STATE_INACTIVE;
+	if (counter->pending_disable) {
+		counter->pending_disable = 0;
+		counter->state = PERF_COUNTER_STATE_OFF;
+	}
 	counter->tstamp_stopped = ctx->time;
 	counter->pmu->disable(counter);
 	counter->oncpu = -1;
@@ -2343,7 +2347,7 @@ static void perf_pending_counter(struct perf_pending_entry *entry)
 
 	if (counter->pending_disable) {
 		counter->pending_disable = 0;
-		perf_counter_disable(counter);
+		__perf_counter_disable(counter);
 	}
 
 	if (counter->pending_wakeup) {
-- 
GitLab


From 94d5d1b2d891f1fd5205f978246b7864d998b25c Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <peterz@infradead.org>
Date: Thu, 13 Aug 2009 16:14:42 +0200
Subject: [PATCH 0817/1153] perf_counter: Report the cloning task as parent on
 perf_counter_fork()

A bug in (9f498cc: perf_counter: Full task tracing) makes
profiling multi-threaded apps it go belly up.

[ output as: (PID:TID):(PPID:PTID) ]

 # ./perf report -D | grep FORK
0x4b0 [0x18]: PERF_EVENT_FORK: (3237:3237):(3236:3236)
0xa10 [0x18]: PERF_EVENT_FORK: (3237:3238):(3236:3236)
0xa70 [0x18]: PERF_EVENT_FORK: (3237:3239):(3236:3236)
0xad0 [0x18]: PERF_EVENT_FORK: (3237:3240):(3236:3236)
0xb18 [0x18]: PERF_EVENT_FORK: (3237:3241):(3236:3236)

Shows us that the test (27d028d perf report: Update for the new
FORK/EXIT events) in builtin-report.c:

        /*
         * A thread clone will have the same PID for both
         * parent and child.
         */
        if (thread == parent)
                return 0;

Will clearly fail.

The problem is that perf_counter_fork() reports the actual
parent, instead of the cloning thread.

Fixing that (with the below patch), yields:

 # ./perf report -D | grep FORK
0x4c8 [0x18]: PERF_EVENT_FORK: (1590:1590):(1589:1589)
0xbd8 [0x18]: PERF_EVENT_FORK: (1590:1591):(1590:1590)
0xc80 [0x18]: PERF_EVENT_FORK: (1590:1592):(1590:1590)
0x3338 [0x18]: PERF_EVENT_FORK: (1590:1593):(1590:1590)
0x66b0 [0x18]: PERF_EVENT_FORK: (1590:1594):(1590:1590)

Which both makes more sense and doesn't confuse perf report
anymore.

Reported-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: paulus@samba.org
Cc: Anton Blanchard <anton@samba.org>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <1250172882.5241.62.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 3f841beefc7..534e20d14d6 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -3028,10 +3028,10 @@ static void perf_counter_task_output(struct perf_counter *counter,
 		return;
 
 	task_event->event.pid = perf_counter_pid(counter, task);
-	task_event->event.ppid = perf_counter_pid(counter, task->real_parent);
+	task_event->event.ppid = perf_counter_pid(counter, current);
 
 	task_event->event.tid = perf_counter_tid(counter, task);
-	task_event->event.ptid = perf_counter_tid(counter, task->real_parent);
+	task_event->event.ptid = perf_counter_tid(counter, current);
 
 	perf_output_put(&handle, task_event->event);
 	perf_output_end(&handle);
-- 
GitLab


From e694958388c50148389b0e9b9e9e8945cf0f1b98 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Thu, 13 Aug 2009 08:28:36 -0700
Subject: [PATCH 0818/1153] Make sock_sendpage() use kernel_sendpage()

kernel_sendpage() does the proper default case handling for when the
socket doesn't have a native sendpage implementation.

Now, arguably this might be something that we could instead solve by
just specifying that all protocols should do it themselves at the
protocol level, but we really only care about the common protocols.
Does anybody really care about sendpage on something like Appletalk? Not
likely.

Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Julien TINNES <julien@cr0.org>
Acked-by: Tavis Ormandy <taviso@sdf.lonestar.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 net/socket.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/socket.c b/net/socket.c
index 791d71a36a9..6d471655904 100644
--- a/net/socket.c
+++ b/net/socket.c
@@ -736,7 +736,7 @@ static ssize_t sock_sendpage(struct file *file, struct page *page,
 	if (more)
 		flags |= MSG_MORE;
 
-	return sock->ops->sendpage(sock, page, offset, size, flags);
+	return kernel_sendpage(sock, page, offset, size, flags);
 }
 
 static ssize_t sock_splice_read(struct file *file, loff_t *ppos,
-- 
GitLab


From 416fbdff2137e8d8cc8f23f517bee3a26b11526f Mon Sep 17 00:00:00 2001
From: "Luis R. Rodriguez" <lrodriguez@atheros.com>
Date: Tue, 11 Aug 2009 13:10:33 -0700
Subject: [PATCH 0819/1153] mac80211: fix panic when splicing unprepared TIDs

We splice skbs from the pending queue for a TID
onto the local pending queue when tearing down a
block ack request. This is not necessary unless we
actually have received a request to start a block ack
request (rate control, for example). If we never received
that request we should not be splicing the tid pending
queue as it would be null, causing a panic.

Not sure yet how exactly we allowed through a call when the
tid state does not have at least HT_ADDBA_REQUESTED_MSK set,
that will require some further review as it is not quite
obvious.

For more information see the bug report:

http://bugzilla.kernel.org/show_bug.cgi?id=13922

This fixes this oops:

BUG: unable to handle kernel NULL pointer dereference at 00000030
IP: [<f8806c70>] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211]
*pdpt = 0000000002d1e001 *pde = 0000000000000000
Thread overran stack, or stack corrupted
Oops: 0000 [#1] SMP
last sysfs file: /sys/module/aes_generic/initstate
Modules linked in: <bleh>

Pid: 0, comm: swapper Not tainted (2.6.31-rc5-wl #2) Dell DV051
EIP: 0060:[<f8806c70>] EFLAGS: 00010292 CPU: 0
EIP is at ieee80211_agg_splice_packets+0x40/0xc0 [mac80211]
EAX: 00000030 EBX: 0000004c ECX: 00000003 EDX: 00000000
ESI: c1c98000 EDI: f745a1c0 EBP: c076be58 ESP: c076be38
 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 0, ti=c076a000 task=c0709160 task.ti=c076a000)
Stack: <bleh2>
Call Trace:
 [<f8806edb>] ? ieee80211_stop_tx_ba_cb+0xab/0x150 [mac80211]
 [<f8802f1e>] ? ieee80211_tasklet_handler+0xce/0x110 [mac80211]
 [<c04862ff>] ? net_rx_action+0xef/0x1d0
 [<c0149378>] ? tasklet_action+0x58/0xc0
 [<c014a0f2>] ? __do_softirq+0xc2/0x190
 [<c018eb48>] ? handle_IRQ_event+0x58/0x140
 [<c01205fe>] ? ack_apic_level+0x7e/0x270
 [<c014a1fd>] ? do_softirq+0x3d/0x40
 [<c014a345>] ? irq_exit+0x65/0x90
 [<c010a6af>] ? do_IRQ+0x4f/0xc0
 [<c014a35d>] ? irq_exit+0x7d/0x90
 [<c011d547>] ? smp_apic_timer_interrupt+0x57/0x90
 [<c01094a9>] ? common_interrupt+0x29/0x30
 [<c010fd9e>] ? mwait_idle+0xbe/0x100
 [<c0107e42>] ? cpu_idle+0x52/0x90
 [<c054b1a5>] ? rest_init+0x55/0x60
 [<c077492d>] ? start_kernel+0x315/0x37d
 [<c07743ce>] ? unknown_bootoption+0x0/0x1f9
 [<c0774099>] ? i386_start_kernel+0x79/0x81
Code: <bleh3>
EIP: [<f8806c70>] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211] SS:ESP 0068:c076be38
CR2: 0000000000000030

Cc: stable@kernel.org
Testedy-by: Jack Lau <jackelectronics@hotmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 net/mac80211/agg-tx.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/net/mac80211/agg-tx.c b/net/mac80211/agg-tx.c
index 9e5762ad307..a24e59816b9 100644
--- a/net/mac80211/agg-tx.c
+++ b/net/mac80211/agg-tx.c
@@ -381,6 +381,14 @@ static void ieee80211_agg_splice_packets(struct ieee80211_local *local,
 		&local->hw, queue,
 		IEEE80211_QUEUE_STOP_REASON_AGGREGATION);
 
+	if (!(sta->ampdu_mlme.tid_state_tx[tid] & HT_ADDBA_REQUESTED_MSK))
+		return;
+
+	if (WARN(!sta->ampdu_mlme.tid_tx[tid],
+		 "TID %d gone but expected when splicing aggregates from"
+		 "the pending queue\n", tid))
+		return;
+
 	if (!skb_queue_empty(&sta->ampdu_mlme.tid_tx[tid]->pending)) {
 		spin_lock_irqsave(&local->queue_stop_reason_lock, flags);
 		/* mark queue as pending, it is stopped already */
-- 
GitLab


From 2d860ad76f4ee4d2eba0fe3797c8d7cdce432cc0 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Thu, 13 Aug 2009 13:05:10 -0700
Subject: [PATCH 0820/1153] genirq: prevent wakeup of freed irq thread

free_irq() can remove an irqaction while the corresponding interrupt
is in progress, but free_irq() sets action->thread to NULL
unconditionally, which might lead to a NULL pointer dereference in
handle_IRQ_event() when the hard interrupt context tries to wake up
the handler thread.

Prevent this by moving the thread stop after synchronize_irq(). No
need to set action->thread to NULL either as action is going to be
freed anyway.

This fixes a boot crash reported against preempt-rt which uses the
mainline irq threads code to implement full irq threading.

[ tglx: removed local irqthread variable ]

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 kernel/irq/manage.c | 17 +++++++----------
 1 file changed, 7 insertions(+), 10 deletions(-)

diff --git a/kernel/irq/manage.c b/kernel/irq/manage.c
index 61c679db468..d222515a5a0 100644
--- a/kernel/irq/manage.c
+++ b/kernel/irq/manage.c
@@ -761,7 +761,6 @@ static struct irqaction *__free_irq(unsigned int irq, void *dev_id)
 {
 	struct irq_desc *desc = irq_to_desc(irq);
 	struct irqaction *action, **action_ptr;
-	struct task_struct *irqthread;
 	unsigned long flags;
 
 	WARN(in_interrupt(), "Trying to free IRQ %d from IRQ context!\n", irq);
@@ -809,9 +808,6 @@ static struct irqaction *__free_irq(unsigned int irq, void *dev_id)
 			desc->chip->disable(irq);
 	}
 
-	irqthread = action->thread;
-	action->thread = NULL;
-
 	spin_unlock_irqrestore(&desc->lock, flags);
 
 	unregister_handler_proc(irq, action);
@@ -819,12 +815,6 @@ static struct irqaction *__free_irq(unsigned int irq, void *dev_id)
 	/* Make sure it's not being used on another CPU: */
 	synchronize_irq(irq);
 
-	if (irqthread) {
-		if (!test_bit(IRQTF_DIED, &action->thread_flags))
-			kthread_stop(irqthread);
-		put_task_struct(irqthread);
-	}
-
 #ifdef CONFIG_DEBUG_SHIRQ
 	/*
 	 * It's a shared IRQ -- the driver ought to be prepared for an IRQ
@@ -840,6 +830,13 @@ static struct irqaction *__free_irq(unsigned int irq, void *dev_id)
 		local_irq_restore(flags);
 	}
 #endif
+
+	if (action->thread) {
+		if (!test_bit(IRQTF_DIED, &action->thread_flags))
+			kthread_stop(action->thread);
+		put_task_struct(action->thread);
+	}
+
 	return action;
 }
 
-- 
GitLab


From 15052c9e85bf0cdadcb69eb89623bf12bad8b4f8 Mon Sep 17 00:00:00 2001
From: "Kashyap, Desai" <kashyap.desai@lsi.com>
Date: Fri, 7 Aug 2009 19:33:17 +0530
Subject: [PATCH 0821/1153] [SCSI] mpt2sas: Introduced check for
 enclosure_handle to avoid crash

Kernel panic is seen because of enclosure_handle received from FW is zero.
Check is introduced before calling mpt2sas_config_get_enclosure_pg0.

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
---
 drivers/scsi/mpt2sas/mpt2sas_scsih.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
index 2a01a5f2a84..b1326bf78c9 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
@@ -3663,12 +3663,11 @@ _scsih_add_device(struct MPT2SAS_ADAPTER *ioc, u16 handle, u8 phy_num, u8 is_pd)
 	sas_device->hidden_raid_component = is_pd;
 
 	/* get enclosure_logical_id */
-	if (!(mpt2sas_config_get_enclosure_pg0(ioc, &mpi_reply, &enclosure_pg0,
-	   MPI2_SAS_ENCLOS_PGAD_FORM_HANDLE,
-	   sas_device->enclosure_handle))) {
+	if (sas_device->enclosure_handle && !(mpt2sas_config_get_enclosure_pg0(
+	   ioc, &mpi_reply, &enclosure_pg0, MPI2_SAS_ENCLOS_PGAD_FORM_HANDLE,
+	   sas_device->enclosure_handle)))
 		sas_device->enclosure_logical_id =
 		    le64_to_cpu(enclosure_pg0.EnclosureLogicalID);
-	}
 
 	/* get device name */
 	sas_device->device_name = le64_to_cpu(sas_device_pg0.DeviceName);
-- 
GitLab


From 20f5895d55d9281830bfb7819c5c5b70b05297a6 Mon Sep 17 00:00:00 2001
From: "Kashyap, Desai" <kashyap.desai@lsi.com>
Date: Fri, 7 Aug 2009 19:34:26 +0530
Subject: [PATCH 0822/1153] [SCSI] mpt2sas: Expander fix oops saying "Already
 part of another port"

Kernel panic is seen because driver did not tear down the port which should
be dnoe using mpt2sas_transport_port_remove(). without this fix When expander
is added back we would oops inside sas_port_add_phy.

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
---
 drivers/scsi/mpt2sas/mpt2sas_scsih.c | 21 +++++++++++++++------
 1 file changed, 15 insertions(+), 6 deletions(-)

diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
index b1326bf78c9..918445e1e65 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
@@ -3426,7 +3426,7 @@ _scsih_expander_add(struct MPT2SAS_ADAPTER *ioc, u16 handle)
 	__le64 sas_address;
 	int i;
 	unsigned long flags;
-	struct _sas_port *mpt2sas_port;
+	struct _sas_port *mpt2sas_port = NULL;
 	int rc = 0;
 
 	if (!handle)
@@ -3518,12 +3518,20 @@ _scsih_expander_add(struct MPT2SAS_ADAPTER *ioc, u16 handle)
 		    &expander_pg1, i, handle))) {
 			printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n",
 			    ioc->name, __FILE__, __LINE__, __func__);
-			continue;
+			rc = -1;
+			goto out_fail;
 		}
 		sas_expander->phy[i].handle = handle;
 		sas_expander->phy[i].phy_id = i;
-		mpt2sas_transport_add_expander_phy(ioc, &sas_expander->phy[i],
-		    expander_pg1, sas_expander->parent_dev);
+
+		if ((mpt2sas_transport_add_expander_phy(ioc,
+		    &sas_expander->phy[i], expander_pg1,
+		    sas_expander->parent_dev))) {
+			printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n",
+			    ioc->name, __FILE__, __LINE__, __func__);
+			rc = -1;
+			goto out_fail;
+		}
 	}
 
 	if (sas_expander->enclosure_handle) {
@@ -3540,8 +3548,9 @@ _scsih_expander_add(struct MPT2SAS_ADAPTER *ioc, u16 handle)
 
  out_fail:
 
-	if (sas_expander)
-		kfree(sas_expander->phy);
+	if (mpt2sas_port)
+		mpt2sas_transport_port_remove(ioc, sas_expander->sas_address,
+		    sas_expander->parent_handle);
 	kfree(sas_expander);
 	return rc;
 }
-- 
GitLab


From 62727a7ba43c0abf2673e3877079c136a9721792 Mon Sep 17 00:00:00 2001
From: "Kashyap, Desai" <kashyap.desai@lsi.com>
Date: Fri, 7 Aug 2009 19:35:18 +0530
Subject: [PATCH 0823/1153] [SCSI] mpt2sas: Raid 10 Value is showing as Raid 1E
 in /va/log/messages

When a volume is activated, the driver will recieve a pair of ir config change
events to remove the foreign volume, then add the native.
In the process of the removal event, the hidden raid componet is removed from
the parent.When the disks is added back, the adding of the port fails becuase
there is no instance of the device in its parent.
To fix this issue, the driver needs to call mpt2sas_transport_update_links()
prior to calling _scsih_add_device. In addition, we added sanity checks on
volume add and removal to ignore events for foreign volumes.

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
---
 drivers/scsi/mpt2sas/mpt2sas_scsih.c | 90 ++++++++++++++++++++--------
 1 file changed, 64 insertions(+), 26 deletions(-)

diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
index 918445e1e65..22a95421e36 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
@@ -4258,12 +4258,6 @@ _scsih_sas_volume_add(struct MPT2SAS_ADAPTER *ioc,
 	u16 handle = le16_to_cpu(element->VolDevHandle);
 	int rc;
 
-#if 0 /* RAID_HACKS */
-	if (le32_to_cpu(event_data->Flags) &
-	    MPI2_EVENT_IR_CHANGE_FLAGS_FOREIGN_CONFIG)
-		return;
-#endif
-
 	mpt2sas_config_get_volume_wwid(ioc, handle, &wwid);
 	if (!wwid) {
 		printk(MPT2SAS_ERR_FMT
@@ -4318,12 +4312,6 @@ _scsih_sas_volume_delete(struct MPT2SAS_ADAPTER *ioc,
 	unsigned long flags;
 	struct MPT2SAS_TARGET *sas_target_priv_data;
 
-#if 0 /* RAID_HACKS */
-	if (le32_to_cpu(event_data->Flags) &
-	    MPI2_EVENT_IR_CHANGE_FLAGS_FOREIGN_CONFIG)
-		return;
-#endif
-
 	spin_lock_irqsave(&ioc->raid_device_lock, flags);
 	raid_device = _scsih_raid_device_find_by_handle(ioc, handle);
 	spin_unlock_irqrestore(&ioc->raid_device_lock, flags);
@@ -4436,14 +4424,38 @@ _scsih_sas_pd_add(struct MPT2SAS_ADAPTER *ioc,
 	struct _sas_device *sas_device;
 	unsigned long flags;
 	u16 handle = le16_to_cpu(element->PhysDiskDevHandle);
+	Mpi2ConfigReply_t mpi_reply;
+	Mpi2SasDevicePage0_t sas_device_pg0;
+	u32 ioc_status;
 
 	spin_lock_irqsave(&ioc->sas_device_lock, flags);
 	sas_device = _scsih_sas_device_find_by_handle(ioc, handle);
 	spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
-	if (sas_device)
+	if (sas_device) {
 		sas_device->hidden_raid_component = 1;
-	else
-		_scsih_add_device(ioc, handle, 0, 1);
+		return;
+	}
+
+	if ((mpt2sas_config_get_sas_device_pg0(ioc, &mpi_reply, &sas_device_pg0,
+	    MPI2_SAS_DEVICE_PGAD_FORM_HANDLE, handle))) {
+		printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n",
+		    ioc->name, __FILE__, __LINE__, __func__);
+		return;
+	}
+
+	ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
+	    MPI2_IOCSTATUS_MASK;
+	if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+		printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n",
+		    ioc->name, __FILE__, __LINE__, __func__);
+		return;
+	}
+
+	_scsih_link_change(ioc,
+	    le16_to_cpu(sas_device_pg0.ParentDevHandle),
+	    handle, sas_device_pg0.PhyNum, MPI2_SAS_NEG_LINK_RATE_1_5);
+
+	_scsih_add_device(ioc, handle, 0, 1);
 }
 
 #ifdef CONFIG_SCSI_MPT2SAS_LOGGING
@@ -4543,12 +4555,15 @@ _scsih_sas_ir_config_change_event(struct MPT2SAS_ADAPTER *ioc, u8 VF_ID,
 {
 	Mpi2EventIrConfigElement_t *element;
 	int i;
+	u8 foreign_config;
 
 #ifdef CONFIG_SCSI_MPT2SAS_LOGGING
 	if (ioc->logging_level & MPT_DEBUG_EVENT_WORK_TASK)
 		_scsih_sas_ir_config_change_event_debug(ioc, event_data);
 
 #endif
+	foreign_config = (le32_to_cpu(event_data->Flags) &
+	    MPI2_EVENT_IR_CHANGE_FLAGS_FOREIGN_CONFIG) ? 1 : 0;
 
 	element = (Mpi2EventIrConfigElement_t *)&event_data->ConfigElement[0];
 	for (i = 0; i < event_data->NumElements; i++, element++) {
@@ -4556,11 +4571,13 @@ _scsih_sas_ir_config_change_event(struct MPT2SAS_ADAPTER *ioc, u8 VF_ID,
 		switch (element->ReasonCode) {
 		case MPI2_EVENT_IR_CHANGE_RC_VOLUME_CREATED:
 		case MPI2_EVENT_IR_CHANGE_RC_ADDED:
-			_scsih_sas_volume_add(ioc, element);
+			if (!foreign_config)
+				_scsih_sas_volume_add(ioc, element);
 			break;
 		case MPI2_EVENT_IR_CHANGE_RC_VOLUME_DELETED:
 		case MPI2_EVENT_IR_CHANGE_RC_REMOVED:
-			_scsih_sas_volume_delete(ioc, element);
+			if (!foreign_config)
+				_scsih_sas_volume_delete(ioc, element);
 			break;
 		case MPI2_EVENT_IR_CHANGE_RC_PD_CREATED:
 			_scsih_sas_pd_hide(ioc, element);
@@ -4679,6 +4696,9 @@ _scsih_sas_ir_physical_disk_event(struct MPT2SAS_ADAPTER *ioc, u8 VF_ID,
 	u32 state;
 	struct _sas_device *sas_device;
 	unsigned long flags;
+	Mpi2ConfigReply_t mpi_reply;
+	Mpi2SasDevicePage0_t sas_device_pg0;
+	u32 ioc_status;
 
 	if (event_data->ReasonCode != MPI2_EVENT_IR_PHYSDISK_RC_STATE_CHANGED)
 		return;
@@ -4695,22 +4715,40 @@ _scsih_sas_ir_physical_disk_event(struct MPT2SAS_ADAPTER *ioc, u8 VF_ID,
 	spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
 
 	switch (state) {
-#if 0
-	case MPI2_RAID_PD_STATE_OFFLINE:
-		if (sas_device)
-			_scsih_remove_device(ioc, handle);
-		break;
-#endif
 	case MPI2_RAID_PD_STATE_ONLINE:
 	case MPI2_RAID_PD_STATE_DEGRADED:
 	case MPI2_RAID_PD_STATE_REBUILDING:
 	case MPI2_RAID_PD_STATE_OPTIMAL:
-		if (sas_device)
+		if (sas_device) {
 			sas_device->hidden_raid_component = 1;
-		else
-			_scsih_add_device(ioc, handle, 0, 1);
+			return;
+		}
+
+		if ((mpt2sas_config_get_sas_device_pg0(ioc, &mpi_reply,
+		    &sas_device_pg0, MPI2_SAS_DEVICE_PGAD_FORM_HANDLE,
+		    handle))) {
+			printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n",
+			    ioc->name, __FILE__, __LINE__, __func__);
+			return;
+		}
+
+		ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
+		    MPI2_IOCSTATUS_MASK;
+		if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+			printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n",
+			    ioc->name, __FILE__, __LINE__, __func__);
+			return;
+		}
+
+		_scsih_link_change(ioc,
+		    le16_to_cpu(sas_device_pg0.ParentDevHandle),
+		    handle, sas_device_pg0.PhyNum, MPI2_SAS_NEG_LINK_RATE_1_5);
+
+		_scsih_add_device(ioc, handle, 0, 1);
+
 		break;
 
+	case MPI2_RAID_PD_STATE_OFFLINE:
 	case MPI2_RAID_PD_STATE_NOT_CONFIGURED:
 	case MPI2_RAID_PD_STATE_NOT_COMPATIBLE:
 	case MPI2_RAID_PD_STATE_HOT_SPARE:
-- 
GitLab


From be9e8cd75ce8d94ae4aab721fdcc337fa78a9090 Mon Sep 17 00:00:00 2001
From: "Kashyap, Desai" <kashyap.desai@lsi.com>
Date: Fri, 7 Aug 2009 19:36:43 +0530
Subject: [PATCH 0824/1153] [SCSI] mpt2sas: Excessive log info causes sas
 iounit page time out

Inhibit 0x3117 loginfos - during cable pull, there are too many printks going
to the syslog, this is have impact on how fast the interrupt routine can handle
keeping up with command completions; this was the root cause to the config
pages timeouts.

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
---
 drivers/scsi/mpt2sas/mpt2sas_base.c  | 4 ++++
 drivers/scsi/mpt2sas/mpt2sas_scsih.c | 4 ++++
 2 files changed, 8 insertions(+)

diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.c b/drivers/scsi/mpt2sas/mpt2sas_base.c
index f3da592f7bc..ed9965e4b96 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_base.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_base.c
@@ -440,6 +440,10 @@ _base_sas_log_info(struct MPT2SAS_ADAPTER *ioc , u32 log_info)
 	if (sas_loginfo.dw.bus_type != 3 /*SAS*/)
 		return;
 
+	/* each nexus loss loginfo */
+	if (log_info == 0x31170000)
+		return;
+
 	/* eat the loginfos associated with task aborts */
 	if (ioc->ignore_loginfos && (log_info == 30050000 || log_info ==
 	    0x31140000 || log_info == 0x31130000))
diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
index 22a95421e36..25c8d8294af 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
@@ -2767,6 +2767,10 @@ _scsih_scsi_ioc_info(struct MPT2SAS_ADAPTER *ioc, struct scsi_cmnd *scmd,
 	char *desc_ioc_state = NULL;
 	char *desc_scsi_status = NULL;
 	char *desc_scsi_state = ioc->tmp_string;
+	u32 log_info = le32_to_cpu(mpi_reply->IOCLogInfo);
+
+	if (log_info == 0x31170000)
+		return;
 
 	switch (ioc_status) {
 	case MPI2_IOCSTATUS_SUCCESS:
-- 
GitLab


From 6bd4e1e4d6023f4da069fd68729c502cc4e6dfd0 Mon Sep 17 00:00:00 2001
From: "Kashyap, Desai" <kashyap.desai@lsi.com>
Date: Fri, 7 Aug 2009 19:37:14 +0530
Subject: [PATCH 0825/1153] [SCSI] mpt2sas: fix infinite loop inside config
 request

This restriction is introduced just to avoid loop of
config_request. Retry must be limited so we have restricted
config request to maximum 2 times.

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
---
 drivers/scsi/mpt2sas/mpt2sas_config.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/scsi/mpt2sas/mpt2sas_config.c b/drivers/scsi/mpt2sas/mpt2sas_config.c
index 58cfb97846f..1c6658c6023 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_config.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_config.c
@@ -247,6 +247,12 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t
 	retry_count = 0;
 
  retry_config:
+	if (retry_count) {
+		if (retry_count > 2) /* attempt only 2 retries */
+			return -EFAULT;
+		printk(MPT2SAS_INFO_FMT "%s: attempting retry (%d)\n",
+		    ioc->name, __func__, retry_count);
+	}
 	wait_state_count = 0;
 	ioc_state = mpt2sas_base_get_iocstate(ioc, 1);
 	while (ioc_state != MPI2_IOC_STATE_OPERATIONAL) {
-- 
GitLab


From e4750c989f732555fca86dd73d488c79972362db Mon Sep 17 00:00:00 2001
From: "Kashyap, Desai" <kashyap.desai@lsi.com>
Date: Fri, 7 Aug 2009 19:37:59 +0530
Subject: [PATCH 0826/1153] [SCSI] mpt2sas: fix crash due to Watchdog is active
 while OS in standby mode

Fix oops ocurring at hibernation time.  This oops was due to the firmware fault
watchdog timer still running after we freed resources. To fix the issue we need
to terminate the watchdog timer at hibernation time.

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
---
 drivers/scsi/mpt2sas/mpt2sas_base.c  | 88 +++++++++++++++++++---------
 drivers/scsi/mpt2sas/mpt2sas_base.h  |  2 +
 drivers/scsi/mpt2sas/mpt2sas_scsih.c |  2 +
 3 files changed, 64 insertions(+), 28 deletions(-)

diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.c b/drivers/scsi/mpt2sas/mpt2sas_base.c
index ed9965e4b96..c29c4f9851b 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_base.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_base.c
@@ -119,6 +119,64 @@ _base_fault_reset_work(struct work_struct *work)
 	spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags);
 }
 
+/**
+ * mpt2sas_base_start_watchdog - start the fault_reset_work_q
+ * @ioc: pointer to scsi command object
+ * Context: sleep.
+ *
+ * Return nothing.
+ */
+void
+mpt2sas_base_start_watchdog(struct MPT2SAS_ADAPTER *ioc)
+{
+	unsigned long	 flags;
+
+	if (ioc->fault_reset_work_q)
+		return;
+
+	/* initialize fault polling */
+	INIT_DELAYED_WORK(&ioc->fault_reset_work, _base_fault_reset_work);
+	snprintf(ioc->fault_reset_work_q_name,
+	    sizeof(ioc->fault_reset_work_q_name), "poll_%d_status", ioc->id);
+	ioc->fault_reset_work_q =
+		create_singlethread_workqueue(ioc->fault_reset_work_q_name);
+	if (!ioc->fault_reset_work_q) {
+		printk(MPT2SAS_ERR_FMT "%s: failed (line=%d)\n",
+		    ioc->name, __func__, __LINE__);
+			return;
+	}
+	spin_lock_irqsave(&ioc->ioc_reset_in_progress_lock, flags);
+	if (ioc->fault_reset_work_q)
+		queue_delayed_work(ioc->fault_reset_work_q,
+		    &ioc->fault_reset_work,
+		    msecs_to_jiffies(FAULT_POLLING_INTERVAL));
+	spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags);
+}
+
+/**
+ * mpt2sas_base_stop_watchdog - stop the fault_reset_work_q
+ * @ioc: pointer to scsi command object
+ * Context: sleep.
+ *
+ * Return nothing.
+ */
+void
+mpt2sas_base_stop_watchdog(struct MPT2SAS_ADAPTER *ioc)
+{
+	unsigned long	 flags;
+	struct workqueue_struct *wq;
+
+	spin_lock_irqsave(&ioc->ioc_reset_in_progress_lock, flags);
+	wq = ioc->fault_reset_work_q;
+	ioc->fault_reset_work_q = NULL;
+	spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags);
+	if (wq) {
+		if (!cancel_delayed_work(&ioc->fault_reset_work))
+			flush_workqueue(wq);
+		destroy_workqueue(wq);
+	}
+}
+
 #ifdef CONFIG_SCSI_MPT2SAS_LOGGING
 /**
  * _base_sas_ioc_info - verbose translation of the ioc status
@@ -3209,7 +3267,6 @@ int
 mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc)
 {
 	int r, i;
-	unsigned long	 flags;
 
 	dinitprintk(ioc, printk(MPT2SAS_DEBUG_FMT "%s\n", ioc->name,
 	    __func__));
@@ -3292,23 +3349,7 @@ mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc)
 	if (r)
 		goto out_free_resources;
 
-	/* initialize fault polling */
-	INIT_DELAYED_WORK(&ioc->fault_reset_work, _base_fault_reset_work);
-	snprintf(ioc->fault_reset_work_q_name,
-	    sizeof(ioc->fault_reset_work_q_name), "poll_%d_status", ioc->id);
-	ioc->fault_reset_work_q =
-		create_singlethread_workqueue(ioc->fault_reset_work_q_name);
-	if (!ioc->fault_reset_work_q) {
-		printk(MPT2SAS_ERR_FMT "%s: failed (line=%d)\n",
-		    ioc->name, __func__, __LINE__);
-			goto out_free_resources;
-	}
-	spin_lock_irqsave(&ioc->ioc_reset_in_progress_lock, flags);
-	if (ioc->fault_reset_work_q)
-		queue_delayed_work(ioc->fault_reset_work_q,
-		    &ioc->fault_reset_work,
-		    msecs_to_jiffies(FAULT_POLLING_INTERVAL));
-	spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags);
+	mpt2sas_base_start_watchdog(ioc);
 	return 0;
 
  out_free_resources:
@@ -3341,20 +3382,11 @@ mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc)
 void
 mpt2sas_base_detach(struct MPT2SAS_ADAPTER *ioc)
 {
-	unsigned long	 flags;
-	struct workqueue_struct *wq;
 
 	dexitprintk(ioc, printk(MPT2SAS_DEBUG_FMT "%s\n", ioc->name,
 	    __func__));
 
-	spin_lock_irqsave(&ioc->ioc_reset_in_progress_lock, flags);
-	wq = ioc->fault_reset_work_q;
-	ioc->fault_reset_work_q = NULL;
-	spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags);
-	if (!cancel_delayed_work(&ioc->fault_reset_work))
-		flush_workqueue(wq);
-	destroy_workqueue(wq);
-
+	mpt2sas_base_stop_watchdog(ioc);
 	mpt2sas_base_free_resources(ioc);
 	_base_release_memory_pools(ioc);
 	kfree(ioc->pfacts);
diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.h b/drivers/scsi/mpt2sas/mpt2sas_base.h
index 286c185fa9e..a29935726e7 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_base.h
+++ b/drivers/scsi/mpt2sas/mpt2sas_base.h
@@ -673,6 +673,8 @@ typedef void (*MPT_CALLBACK)(struct MPT2SAS_ADAPTER *ioc, u16 smid, u8 VF_ID,
 
 /* base shared API */
 extern struct list_head mpt2sas_ioc_list;
+void mpt2sas_base_start_watchdog(struct MPT2SAS_ADAPTER *ioc);
+void mpt2sas_base_stop_watchdog(struct MPT2SAS_ADAPTER *ioc);
 
 int mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc);
 void mpt2sas_base_detach(struct MPT2SAS_ADAPTER *ioc);
diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
index 25c8d8294af..2e9a4445596 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
@@ -5824,6 +5824,7 @@ _scsih_suspend(struct pci_dev *pdev, pm_message_t state)
 	struct MPT2SAS_ADAPTER *ioc = shost_priv(shost);
 	u32 device_state;
 
+	mpt2sas_base_stop_watchdog(ioc);
 	flush_scheduled_work();
 	scsi_block_requests(shost);
 	device_state = pci_choose_state(pdev, state);
@@ -5866,6 +5867,7 @@ _scsih_resume(struct pci_dev *pdev)
 
 	mpt2sas_base_hard_reset_handler(ioc, CAN_SLEEP, SOFT_RESET);
 	scsi_unblock_requests(shost);
+	mpt2sas_base_start_watchdog(ioc);
 	return 0;
 }
 #endif /* CONFIG_PM */
-- 
GitLab


From fcfe6392d18283df3c561b5ef59c330d485ff8ca Mon Sep 17 00:00:00 2001
From: "Kashyap, Desai" <kashyap.desai@lsi.com>
Date: Fri, 7 Aug 2009 19:38:48 +0530
Subject: [PATCH 0827/1153] [SCSI] mpt2sas: fix oops because drv data points to
 NULL on resume from hibernate

Fix another ocurring when the system resumes.  This oops was due to driver
setting the pci drvdata to NULL on the prior hibernation.  Becuase it was
set to NULL, upon resmume we assume the pci drvdata is non-zero, and we oops.
To fix the ooops, we don't set pci drvdata to NULL at hibernation time.

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
---
 drivers/scsi/mpt2sas/mpt2sas_base.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.c b/drivers/scsi/mpt2sas/mpt2sas_base.c
index c29c4f9851b..35a13867495 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_base.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_base.c
@@ -1171,7 +1171,6 @@ mpt2sas_base_map_resources(struct MPT2SAS_ADAPTER *ioc)
 		}
 	}
 
-	pci_set_drvdata(pdev, ioc->shost);
 	_base_mask_interrupts(ioc);
 	r = _base_enable_msix(ioc);
 	if (r)
@@ -1194,7 +1193,6 @@ mpt2sas_base_map_resources(struct MPT2SAS_ADAPTER *ioc)
 	ioc->pci_irq = -1;
 	pci_release_selected_regions(ioc->pdev, ioc->bars);
 	pci_disable_device(pdev);
-	pci_set_drvdata(pdev, NULL);
 	return r;
 }
 
@@ -3253,7 +3251,6 @@ mpt2sas_base_free_resources(struct MPT2SAS_ADAPTER *ioc)
 	ioc->chip_phys = 0;
 	pci_release_selected_regions(ioc->pdev, ioc->bars);
 	pci_disable_device(pdev);
-	pci_set_drvdata(pdev, NULL);
 	return;
 }
 
@@ -3275,6 +3272,7 @@ mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc)
 	if (r)
 		return r;
 
+	pci_set_drvdata(ioc->pdev, ioc->shost);
 	r = _base_make_ioc_ready(ioc, CAN_SLEEP, SOFT_RESET);
 	if (r)
 		goto out_free_resources;
@@ -3357,6 +3355,7 @@ mpt2sas_base_attach(struct MPT2SAS_ADAPTER *ioc)
 	ioc->remove_host = 1;
 	mpt2sas_base_free_resources(ioc);
 	_base_release_memory_pools(ioc);
+	pci_set_drvdata(ioc->pdev, NULL);
 	kfree(ioc->tm_cmds.reply);
 	kfree(ioc->transport_cmds.reply);
 	kfree(ioc->config_cmds.reply);
@@ -3389,6 +3388,7 @@ mpt2sas_base_detach(struct MPT2SAS_ADAPTER *ioc)
 	mpt2sas_base_stop_watchdog(ioc);
 	mpt2sas_base_free_resources(ioc);
 	_base_release_memory_pools(ioc);
+	pci_set_drvdata(ioc->pdev, NULL);
 	kfree(ioc->pfacts);
 	kfree(ioc->ctl_cmds.reply);
 	kfree(ioc->base_cmds.reply);
-- 
GitLab


From f9b14c9183b250cf128c7d2341e6b9bdbbcd8f35 Mon Sep 17 00:00:00 2001
From: "Kashyap, Desai" <kashyap.desai@lsi.com>
Date: Fri, 7 Aug 2009 19:39:59 +0530
Subject: [PATCH 0828/1153] [SCSI] mpt2sas: Bump driver version 01.100.04.00

Bump version to 01.100.04.00

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
---
 drivers/scsi/mpt2sas/mpt2sas_base.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.h b/drivers/scsi/mpt2sas/mpt2sas_base.h
index a29935726e7..acdcff150a3 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_base.h
+++ b/drivers/scsi/mpt2sas/mpt2sas_base.h
@@ -69,10 +69,10 @@
 #define MPT2SAS_DRIVER_NAME		"mpt2sas"
 #define MPT2SAS_AUTHOR	"LSI Corporation <DL-MPTFusionLinux@lsi.com>"
 #define MPT2SAS_DESCRIPTION	"LSI MPT Fusion SAS 2.0 Device Driver"
-#define MPT2SAS_DRIVER_VERSION		"01.100.03.00"
+#define MPT2SAS_DRIVER_VERSION		"01.100.04.00"
 #define MPT2SAS_MAJOR_VERSION		01
 #define MPT2SAS_MINOR_VERSION		100
-#define MPT2SAS_BUILD_VERSION		03
+#define MPT2SAS_BUILD_VERSION		04
 #define MPT2SAS_RELEASE_VERSION		00
 
 /*
-- 
GitLab


From 64f1607ffbbc772685733ea63e6f7f4183df1b16 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Thu, 13 Aug 2009 15:43:34 -0700
Subject: [PATCH 0829/1153] Linux 2.6.31-rc6

---
 Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Makefile b/Makefile
index 0d46615bffe..abcfa85f8f8 100644
--- a/Makefile
+++ b/Makefile
@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 31
-EXTRAVERSION = -rc5
+EXTRAVERSION = -rc6
 NAME = Man-Eating Seals of Antiquity
 
 # *DOCUMENTATION*
-- 
GitLab


From 993e6f2fd487e2acddd711f79cf48f3420731382 Mon Sep 17 00:00:00 2001
From: Oliver Hartkopp <oliver@hartkopp.net>
Date: Tue, 11 Aug 2009 02:41:24 +0000
Subject: [PATCH 0830/1153] can: fix oops caused by wrong rtnl newlink usage

For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created with
the ip tool ...

The invocation of 'ip link add type can' lead to an oops as the standard rtnl
newlink function was called:

http://bugzilla.kernel.org/show_bug.cgi?id=13954

This patch adds a private newlink function for the CAN device driver interface
that unconditionally returns -EOPNOTSUPP.

Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Reported-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/can/dev.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/net/can/dev.c b/drivers/net/can/dev.c
index 9e4283aff82..e1a4f821423 100644
--- a/drivers/net/can/dev.c
+++ b/drivers/net/can/dev.c
@@ -611,11 +611,18 @@ nla_put_failure:
 	return -EMSGSIZE;
 }
 
+static int can_newlink(struct net_device *dev,
+		       struct nlattr *tb[], struct nlattr *data[])
+{
+	return -EOPNOTSUPP;
+}
+
 static struct rtnl_link_ops can_link_ops __read_mostly = {
 	.kind		= "can",
 	.maxtype	= IFLA_CAN_MAX,
 	.policy		= can_policy,
 	.setup		= can_setup,
+	.newlink	= can_newlink,
 	.changelink	= can_changelink,
 	.fill_info	= can_fill_info,
 	.fill_xstats	= can_fill_xstats,
-- 
GitLab


From 237057ad3fe5644fa471be474a160de2fc2e5870 Mon Sep 17 00:00:00 2001
From: Don Skidmore <donald.c.skidmore@intel.com>
Date: Tue, 11 Aug 2009 13:18:14 +0000
Subject: [PATCH 0831/1153] ixgbe: fix issues setting rx-usecs with legacy
 interrupts

Currently setting rx-usecs when the interface is in legacy interrupt
mode it is not immediate.  We were only setting EITR for each MSIx
vector and since this count would be zero for legacy mode it wasn't
set until after a reset.  This patch corrects that by checking what
mode we are in and then setting EITR accordingly.

Signed-off-by: Don Skidmore <donald.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ixgbe/ixgbe_ethtool.c | 27 +++++++++++++++++++--------
 1 file changed, 19 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c
index 79144e950a3..dff8dfac7ed 100644
--- a/drivers/net/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ixgbe/ixgbe_ethtool.c
@@ -1948,6 +1948,7 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
                               struct ethtool_coalesce *ec)
 {
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
+	struct ixgbe_q_vector *q_vector;
 	int i;
 
 	if (ec->tx_max_coalesced_frames_irq)
@@ -1982,14 +1983,24 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
 		adapter->itr_setting = 0;
 	}
 
-	for (i = 0; i < adapter->num_msix_vectors - NON_Q_VECTORS; i++) {
-		struct ixgbe_q_vector *q_vector = adapter->q_vector[i];
-		if (q_vector->txr_count && !q_vector->rxr_count)
-			/* tx vector gets half the rate */
-			q_vector->eitr = (adapter->eitr_param >> 1);
-		else
-			/* rx only or mixed */
-			q_vector->eitr = adapter->eitr_param;
+	/* MSI/MSIx Interrupt Mode */
+	if (adapter->flags &
+	    (IXGBE_FLAG_MSIX_ENABLED | IXGBE_FLAG_MSI_ENABLED)) {
+		int num_vectors = adapter->num_msix_vectors - NON_Q_VECTORS;
+		for (i = 0; i < num_vectors; i++) {
+			q_vector = adapter->q_vector[i];
+			if (q_vector->txr_count && !q_vector->rxr_count)
+				/* tx vector gets half the rate */
+				q_vector->eitr = (adapter->eitr_param >> 1);
+			else
+				/* rx only or mixed */
+				q_vector->eitr = adapter->eitr_param;
+			ixgbe_write_eitr(q_vector);
+		}
+	/* Legacy Interrupt Mode */
+	} else {
+		q_vector = adapter->q_vector[0];
+		q_vector->eitr = adapter->eitr_param;
 		ixgbe_write_eitr(q_vector);
 	}
 
-- 
GitLab


From e424fa9d6a0add1a9b812b07e3607daaa5b9e53d Mon Sep 17 00:00:00 2001
From: Amit Kumar Salecha <amit@qlogic.com>
Date: Thu, 13 Aug 2009 07:03:00 +0000
Subject: [PATCH 0832/1153] netxen: remove netxen workqueue

o Remove private workqueue in the driver, move all
  scheduled tasks to keventd workqueues. This makes
  ports (interfaces) of same / different NIC boards
  independent, in terms of their link watchdog and
  reset tasks.

o Move quick checks for link status and temperature
  in timer callback, schedule watchdog task only if
  link status changed or temperature reached critical
  threshold.

This also fixes deadlock when thermal panic occurs,
watchdog work was flushing workqueue that it was
sitting on.

Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/netxen/netxen_nic.h      |  2 +-
 drivers/net/netxen/netxen_nic_main.c | 69 +++++++++++++++++-----------
 2 files changed, 42 insertions(+), 29 deletions(-)

diff --git a/drivers/net/netxen/netxen_nic.h b/drivers/net/netxen/netxen_nic.h
index f86e05047d1..a9c1fcca5e7 100644
--- a/drivers/net/netxen/netxen_nic.h
+++ b/drivers/net/netxen/netxen_nic.h
@@ -1254,7 +1254,7 @@ struct netxen_adapter {
 	u8 mc_enabled;
 	u8 max_mc_count;
 	u8 rss_supported;
-	u8 resv2;
+	u8 link_changed;
 	u32 resv3;
 
 	u8 has_link_events;
diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c
index 70c05c4c0ca..d24e1cb93a2 100644
--- a/drivers/net/netxen/netxen_nic_main.c
+++ b/drivers/net/netxen/netxen_nic_main.c
@@ -94,10 +94,6 @@ static struct pci_device_id netxen_pci_tbl[] __devinitdata = {
 
 MODULE_DEVICE_TABLE(pci, netxen_pci_tbl);
 
-static struct workqueue_struct *netxen_workq;
-#define SCHEDULE_WORK(tp)	queue_work(netxen_workq, tp)
-#define FLUSH_SCHEDULED_WORK()	flush_workqueue(netxen_workq)
-
 static void netxen_watchdog(unsigned long);
 
 static uint32_t crb_cmd_producer[4] = {
@@ -880,7 +876,6 @@ netxen_nic_down(struct netxen_adapter *adapter, struct net_device *netdev)
 	spin_unlock(&adapter->tx_clean_lock);
 
 	del_timer_sync(&adapter->watchdog_timer);
-	FLUSH_SCHEDULED_WORK();
 }
 
 
@@ -1177,6 +1172,9 @@ static void __devexit netxen_nic_remove(struct pci_dev *pdev)
 
 	unregister_netdev(netdev);
 
+	cancel_work_sync(&adapter->watchdog_task);
+	cancel_work_sync(&adapter->tx_timeout_task);
+
 	if (adapter->is_up == NETXEN_ADAPTER_UP_MAGIC) {
 		netxen_nic_detach(adapter);
 	}
@@ -1211,6 +1209,9 @@ netxen_nic_suspend(struct pci_dev *pdev, pm_message_t state)
 	if (netif_running(netdev))
 		netxen_nic_down(adapter, netdev);
 
+	cancel_work_sync(&adapter->watchdog_task);
+	cancel_work_sync(&adapter->tx_timeout_task);
+
 	if (adapter->is_up == NETXEN_ADAPTER_UP_MAGIC)
 		netxen_nic_detach(adapter);
 
@@ -1549,11 +1550,6 @@ static int netxen_nic_check_temp(struct netxen_adapter *adapter)
 		       "%s: Device temperature %d degrees C exceeds"
 		       " maximum allowed. Hardware has been shut down.\n",
 		       netdev->name, temp_val);
-
-		netif_device_detach(netdev);
-		netxen_nic_down(adapter, netdev);
-		netxen_nic_detach(adapter);
-
 		rv = 1;
 	} else if (temp_state == NX_TEMP_WARN) {
 		if (adapter->temp == NX_TEMP_NORMAL) {
@@ -1587,10 +1583,7 @@ void netxen_advert_link_change(struct netxen_adapter *adapter, int linkup)
 			netif_carrier_off(netdev);
 			netif_stop_queue(netdev);
 		}
-
-		if (!adapter->has_link_events)
-			netxen_nic_set_link_parameters(adapter);
-
+		adapter->link_changed = !adapter->has_link_events;
 	} else if (!adapter->ahw.linkup && linkup) {
 		printk(KERN_INFO "%s: %s NIC Link is up\n",
 		       netxen_nic_driver_name, netdev->name);
@@ -1599,9 +1592,7 @@ void netxen_advert_link_change(struct netxen_adapter *adapter, int linkup)
 			netif_carrier_on(netdev);
 			netif_wake_queue(netdev);
 		}
-
-		if (!adapter->has_link_events)
-			netxen_nic_set_link_parameters(adapter);
+		adapter->link_changed = !adapter->has_link_events;
 	}
 }
 
@@ -1628,11 +1619,36 @@ static void netxen_nic_handle_phy_intr(struct netxen_adapter *adapter)
 	netxen_advert_link_change(adapter, linkup);
 }
 
+static void netxen_nic_thermal_shutdown(struct netxen_adapter *adapter)
+{
+	struct net_device *netdev = adapter->netdev;
+
+	netif_device_detach(netdev);
+	netxen_nic_down(adapter, netdev);
+	netxen_nic_detach(adapter);
+}
+
 static void netxen_watchdog(unsigned long v)
 {
 	struct netxen_adapter *adapter = (struct netxen_adapter *)v;
 
-	SCHEDULE_WORK(&adapter->watchdog_task);
+	if (netxen_nic_check_temp(adapter))
+		goto do_sched;
+
+	if (!adapter->has_link_events) {
+		netxen_nic_handle_phy_intr(adapter);
+
+		if (adapter->link_changed)
+			goto do_sched;
+	}
+
+	if (netif_running(adapter->netdev))
+		mod_timer(&adapter->watchdog_timer, jiffies + 2 * HZ);
+
+	return;
+
+do_sched:
+	schedule_work(&adapter->watchdog_task);
 }
 
 void netxen_watchdog_task(struct work_struct *work)
@@ -1640,11 +1656,13 @@ void netxen_watchdog_task(struct work_struct *work)
 	struct netxen_adapter *adapter =
 		container_of(work, struct netxen_adapter, watchdog_task);
 
-	if (netxen_nic_check_temp(adapter))
+	if (adapter->temp == NX_TEMP_PANIC) {
+		netxen_nic_thermal_shutdown(adapter);
 		return;
+	}
 
-	if (!adapter->has_link_events)
-		netxen_nic_handle_phy_intr(adapter);
+	if (adapter->link_changed)
+		netxen_nic_set_link_parameters(adapter);
 
 	if (netif_running(adapter->netdev))
 		mod_timer(&adapter->watchdog_timer, jiffies + 2 * HZ);
@@ -1652,9 +1670,8 @@ void netxen_watchdog_task(struct work_struct *work)
 
 static void netxen_tx_timeout(struct net_device *netdev)
 {
-	struct netxen_adapter *adapter = (struct netxen_adapter *)
-						netdev_priv(netdev);
-	SCHEDULE_WORK(&adapter->tx_timeout_task);
+	struct netxen_adapter *adapter = netdev_priv(netdev);
+	schedule_work(&adapter->tx_timeout_task);
 }
 
 static void netxen_tx_timeout_task(struct work_struct *work)
@@ -1811,9 +1828,6 @@ static int __init netxen_init_module(void)
 {
 	printk(KERN_INFO "%s\n", netxen_nic_driver_string);
 
-	if ((netxen_workq = create_singlethread_workqueue("netxen")) == NULL)
-		return -ENOMEM;
-
 	return pci_register_driver(&netxen_driver);
 }
 
@@ -1822,7 +1836,6 @@ module_init(netxen_init_module);
 static void __exit netxen_exit_module(void)
 {
 	pci_unregister_driver(&netxen_driver);
-	destroy_workqueue(netxen_workq);
 }
 
 module_exit(netxen_exit_module);
-- 
GitLab


From 232e7d68d50c9ac3a55d716e5ae215ecd1e043b9 Mon Sep 17 00:00:00 2001
From: Dhananjay Phadke <dhananjay@netxen.com>
Date: Thu, 13 Aug 2009 07:03:01 +0000
Subject: [PATCH 0833/1153] netxen: free napi resources during detach

o Defer napi resouce allocation to device attach.

o Free napi resources and delete napi during detach.

This ensures right behavior across firmware reset.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/netxen/netxen_nic_init.c |  7 ------
 drivers/net/netxen/netxen_nic_main.c | 32 +++++++++++++++++++++-------
 2 files changed, 24 insertions(+), 15 deletions(-)

diff --git a/drivers/net/netxen/netxen_nic_init.c b/drivers/net/netxen/netxen_nic_init.c
index 7acf204e38c..5d3343ef3d8 100644
--- a/drivers/net/netxen/netxen_nic_init.c
+++ b/drivers/net/netxen/netxen_nic_init.c
@@ -184,13 +184,6 @@ void netxen_free_sw_resources(struct netxen_adapter *adapter)
 	kfree(recv_ctx->rds_rings);
 
 skip_rds:
-	if (recv_ctx->sds_rings == NULL)
-		goto skip_sds;
-
-	for(ring = 0; ring < adapter->max_sds_rings; ring++)
-		recv_ctx->sds_rings[ring].consumer = 0;
-
-skip_sds:
 	if (adapter->tx_ring == NULL)
 		return;
 
diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c
index d24e1cb93a2..28f270f5ac7 100644
--- a/drivers/net/netxen/netxen_nic_main.c
+++ b/drivers/net/netxen/netxen_nic_main.c
@@ -167,6 +167,8 @@ netxen_free_sds_rings(struct netxen_recv_context *recv_ctx)
 {
 	if (recv_ctx->sds_rings != NULL)
 		kfree(recv_ctx->sds_rings);
+
+	recv_ctx->sds_rings = NULL;
 }
 
 static int
@@ -188,6 +190,21 @@ netxen_napi_add(struct netxen_adapter *adapter, struct net_device *netdev)
 	return 0;
 }
 
+static void
+netxen_napi_del(struct netxen_adapter *adapter)
+{
+	int ring;
+	struct nx_host_sds_ring *sds_ring;
+	struct netxen_recv_context *recv_ctx = &adapter->recv_ctx;
+
+	for (ring = 0; ring < adapter->max_sds_rings; ring++) {
+		sds_ring = &recv_ctx->sds_rings[ring];
+		netif_napi_del(&sds_ring->napi);
+	}
+
+	netxen_free_sds_rings(&adapter->recv_ctx);
+}
+
 static void
 netxen_napi_enable(struct netxen_adapter *adapter)
 {
@@ -889,10 +906,12 @@ netxen_nic_attach(struct netxen_adapter *adapter)
 	struct nx_host_tx_ring *tx_ring;
 
 	err = netxen_init_firmware(adapter);
-	if (err != 0) {
-		printk(KERN_ERR "Failed to init firmware\n");
-		return -EIO;
-	}
+	if (err)
+		return err;
+
+	err = netxen_napi_add(adapter, netdev);
+	if (err)
+		return err;
 
 	if (adapter->fw_major < 4)
 		adapter->max_rds_rings = 3;
@@ -956,6 +975,7 @@ netxen_nic_detach(struct netxen_adapter *adapter)
 	netxen_free_hw_resources(adapter);
 	netxen_release_rx_buffers(adapter);
 	netxen_nic_free_irq(adapter);
+	netxen_napi_del(adapter);
 	netxen_free_sw_resources(adapter);
 
 	adapter->is_up = 0;
@@ -1100,9 +1120,6 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 
 	netdev->irq = adapter->msix_entries[0].vector;
 
-	if (netxen_napi_add(adapter, netdev))
-		goto err_out_disable_msi;
-
 	init_timer(&adapter->watchdog_timer);
 	adapter->watchdog_timer.function = &netxen_watchdog;
 	adapter->watchdog_timer.data = (unsigned long)adapter;
@@ -1183,7 +1200,6 @@ static void __devexit netxen_nic_remove(struct pci_dev *pdev)
 		netxen_free_adapter_offload(adapter);
 
 	netxen_teardown_intr(adapter);
-	netxen_free_sds_rings(&adapter->recv_ctx);
 
 	netxen_cleanup_pci_map(adapter);
 
-- 
GitLab


From 5b766182a110311fbf618f736bc8a8f2f7ce3f4c Mon Sep 17 00:00:00 2001
From: Antonio Ospite <ospite@studenti.unina.it>
Date: Wed, 22 Jul 2009 17:20:50 -0300
Subject: [PATCH 0834/1153] V4L/DVB (12330): pxa_camera: Fix Oops in
 pxa_camera_probe

mclk_get_divisor uses pcdev->soc_host.dev, make sure it is initialized.

Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/pxa_camera.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/video/pxa_camera.c b/drivers/media/video/pxa_camera.c
index 46e0d8ad880..e048d25798c 100644
--- a/drivers/media/video/pxa_camera.c
+++ b/drivers/media/video/pxa_camera.c
@@ -1579,6 +1579,7 @@ static int __devinit pxa_camera_probe(struct platform_device *pdev)
 		pcdev->mclk = 20000000;
 	}
 
+	pcdev->soc_host.dev = &pdev->dev;
 	pcdev->mclk_divisor = mclk_get_divisor(pcdev);
 
 	INIT_LIST_HEAD(&pcdev->capture);
@@ -1644,7 +1645,6 @@ static int __devinit pxa_camera_probe(struct platform_device *pdev)
 	pcdev->soc_host.drv_name	= PXA_CAM_DRV_NAME;
 	pcdev->soc_host.ops		= &pxa_soc_camera_host_ops;
 	pcdev->soc_host.priv		= pcdev;
-	pcdev->soc_host.dev		= &pdev->dev;
 	pcdev->soc_host.nr		= pdev->id;
 
 	err = soc_camera_host_register(&pcdev->soc_host);
-- 
GitLab


From ed18d0c87ee0ab6e0985d83c19cd135b1bd54998 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Thu, 23 Jul 2009 21:46:57 -0300
Subject: [PATCH 0835/1153] V4L/DVB (12337): ivtv: Read buffer overflow

This mistakenly tests against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/ivtv/ivtv-controls.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/media/video/ivtv/ivtv-controls.c b/drivers/media/video/ivtv/ivtv-controls.c
index a3b77ed3f08..4a9c8ce0ecb 100644
--- a/drivers/media/video/ivtv/ivtv-controls.c
+++ b/drivers/media/video/ivtv/ivtv-controls.c
@@ -17,6 +17,7 @@
     along with this program; if not, write to the Free Software
     Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
+#include <linux/kernel.h>
 
 #include "ivtv-driver.h"
 #include "ivtv-cards.h"
@@ -281,7 +282,7 @@ int ivtv_s_ext_ctrls(struct file *file, void *fh, struct v4l2_ext_controls *c)
 		idx = p.audio_properties & 0x03;
 		/* The audio clock of the digitizer must match the codec sample
 		   rate otherwise you get some very strange effects. */
-		if (idx < sizeof(freqs))
+		if (idx < ARRAY_SIZE(freqs))
 			ivtv_call_all(itv, audio, s_clock_freq, freqs[idx]);
 		return err;
 	}
-- 
GitLab


From 225aeb1c5863bc92c6bb1f921e9a6cf4d15dbb2a Mon Sep 17 00:00:00 2001
From: Andy Walls <awalls@radix.net>
Date: Thu, 23 Jul 2009 21:51:29 -0300
Subject: [PATCH 0836/1153] V4L/DVB (12338): cx18: Read buffer overflow

This mistakenly tested against sizeof(freqs) instead of the array size. Due to
the mask the only illegal value possible was 3.

Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/cx18/cx18-controls.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/media/video/cx18/cx18-controls.c b/drivers/media/video/cx18/cx18-controls.c
index 5136df19833..93f0dae0135 100644
--- a/drivers/media/video/cx18/cx18-controls.c
+++ b/drivers/media/video/cx18/cx18-controls.c
@@ -20,6 +20,7 @@
  *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA
  *  02111-1307  USA
  */
+#include <linux/kernel.h>
 
 #include "cx18-driver.h"
 #include "cx18-cards.h"
@@ -317,7 +318,7 @@ int cx18_s_ext_ctrls(struct file *file, void *fh, struct v4l2_ext_controls *c)
 		idx = p.audio_properties & 0x03;
 		/* The audio clock of the digitizer must match the codec sample
 		   rate otherwise you get some very strange effects. */
-		if (idx < sizeof(freqs))
+		if (idx < ARRAY_SIZE(freqs))
 			cx18_call_all(cx, audio, s_clock_freq, freqs[idx]);
 		return err;
 	}
-- 
GitLab


From 296544e15a7126373851abd40acc526b79b91432 Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Mon, 27 Jul 2009 08:24:29 -0300
Subject: [PATCH 0837/1153] V4L/DVB (12340): mtv9v011: Add a missing chip
 version to the driver

Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From
the revision history at the mt9v011 datasheet, it seems that the chip
version has changed from the first release of the chip.

Thanks-to hermann pitton <hermann-pitton@arcor.de> for pointing this to
me, on his tests with a Silvercrest webcam.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-cards.c |  3 ++-
 drivers/media/video/mt9v011.c             | 14 +++++++++-----
 drivers/media/video/mt9v011.h             |  3 ++-
 3 files changed, 13 insertions(+), 7 deletions(-)

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index 320f1f60276..bc213a1f9c1 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -1771,7 +1771,8 @@ static int em28xx_hint_sensor(struct em28xx *dev)
 	version = be16_to_cpu(version_be);
 
 	switch (version) {
-	case 0x8243:		/* mt9v011 640x480 1.3 Mpix sensor */
+	case 0x8232:		/* mt9v011 640x480 1.3 Mpix sensor */
+	case 0x8243:		/* mt9v011 rev B 640x480 1.3 Mpix sensor */
 		dev->model = EM2820_BOARD_SILVERCREST_WEBCAM;
 		sensor_name = "mt9v011";
 		dev->em28xx_sensor = EM28XX_MT9V011;
diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c
index b2260de645f..c14bf47d692 100644
--- a/drivers/media/video/mt9v011.c
+++ b/drivers/media/video/mt9v011.c
@@ -393,10 +393,13 @@ static int mt9v011_s_register(struct v4l2_subdev *sd,
 static int mt9v011_g_chip_ident(struct v4l2_subdev *sd,
 				struct v4l2_dbg_chip_ident *chip)
 {
+	u16 version;
 	struct i2c_client *client = v4l2_get_subdevdata(sd);
 
+	version = mt9v011_read(sd, R00_MT9V011_CHIP_VERSION);
+
 	return v4l2_chip_ident_i2c_client(client, chip, V4L2_IDENT_MT9V011,
-					  MT9V011_VERSION);
+					  version);
 }
 
 static const struct v4l2_subdev_core_ops mt9v011_core_ops = {
@@ -449,8 +452,9 @@ static int mt9v011_probe(struct i2c_client *c,
 
 	/* Check if the sensor is really a MT9V011 */
 	version = mt9v011_read(sd, R00_MT9V011_CHIP_VERSION);
-	if (version != MT9V011_VERSION) {
-		v4l2_info(sd, "*** unknown micron chip detected (0x%04x.\n",
+	if ((version != MT9V011_VERSION) &&
+	    (version != MT9V011_REV_B_VERSION)) {
+		v4l2_info(sd, "*** unknown micron chip detected (0x%04x).\n",
 			  version);
 		kfree(core);
 		return -EINVAL;
@@ -461,8 +465,8 @@ static int mt9v011_probe(struct i2c_client *c,
 	core->height = 480;
 	core->xtal = 27000000;	/* Hz */
 
-	v4l_info(c, "chip found @ 0x%02x (%s)\n",
-		 c->addr << 1, c->adapter->name);
+	v4l_info(c, "chip found @ 0x%02x (%s - chip version 0x%04x)\n",
+		 c->addr << 1, c->adapter->name, version);
 
 	return 0;
 }
diff --git a/drivers/media/video/mt9v011.h b/drivers/media/video/mt9v011.h
index 9e443ee3055..3350fd6083c 100644
--- a/drivers/media/video/mt9v011.h
+++ b/drivers/media/video/mt9v011.h
@@ -30,6 +30,7 @@
 #define R35_MT9V011_GLOBAL_GAIN		0x35
 #define RF1_MT9V011_CHIP_ENABLE		0xf1
 
-#define MT9V011_VERSION			0x8243
+#define MT9V011_VERSION			0x8232
+#define MT9V011_REV_B_VERSION		0x8243
 
 #endif
-- 
GitLab


From 458f9aa391efd34867f8cabac2e2f1af00cbc562 Mon Sep 17 00:00:00 2001
From: Jan Nikitenko <jan.nikitenko@gmail.com>
Date: Thu, 18 Jun 2009 08:11:57 -0300
Subject: [PATCH 0838/1153] V4L/DVB (12341): zl10353 and qt1010: fix stack
 corruption bug

Fixes stack corruption bug present in dump_regs function of zl10353 and
qt1010 drivers: the buffer buf was one byte smaller than required -
there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom
bytes per line and 1 byte for zero ending the string required, i.e. 53
bytes, but only 52 were provided.

The one byte missing in stack based buffer buf can cause stack
corruption possibly leading to kernel oops, as discovered originally
with af9015 driver (af9015: fix stack corruption bug).

Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/common/tuners/qt1010.c  | 12 +++++-------
 drivers/media/dvb/frontends/zl10353.c | 12 +++++-------
 2 files changed, 10 insertions(+), 14 deletions(-)

diff --git a/drivers/media/common/tuners/qt1010.c b/drivers/media/common/tuners/qt1010.c
index 825aa1412e6..9f5dba244cb 100644
--- a/drivers/media/common/tuners/qt1010.c
+++ b/drivers/media/common/tuners/qt1010.c
@@ -64,24 +64,22 @@ static int qt1010_writereg(struct qt1010_priv *priv, u8 reg, u8 val)
 /* dump all registers */
 static void qt1010_dump_regs(struct qt1010_priv *priv)
 {
-	char buf[52], buf2[4];
 	u8 reg, val;
 
 	for (reg = 0; ; reg++) {
 		if (reg % 16 == 0) {
 			if (reg)
-				printk("%s\n", buf);
-			sprintf(buf, "%02x: ", reg);
+				printk(KERN_CONT "\n");
+			printk(KERN_DEBUG "%02x:", reg);
 		}
 		if (qt1010_readreg(priv, reg, &val) == 0)
-			sprintf(buf2, "%02x ", val);
+			printk(KERN_CONT " %02x", val);
 		else
-			strcpy(buf2, "-- ");
-		strcat(buf, buf2);
+			printk(KERN_CONT " --");
 		if (reg == 0x2f)
 			break;
 	}
-	printk("%s\n", buf);
+	printk(KERN_CONT "\n");
 }
 
 static int qt1010_set_params(struct dvb_frontend *fe,
diff --git a/drivers/media/dvb/frontends/zl10353.c b/drivers/media/dvb/frontends/zl10353.c
index 148b6f7f6cb..66f5c1fb307 100644
--- a/drivers/media/dvb/frontends/zl10353.c
+++ b/drivers/media/dvb/frontends/zl10353.c
@@ -98,7 +98,6 @@ static int zl10353_read_register(struct zl10353_state *state, u8 reg)
 static void zl10353_dump_regs(struct dvb_frontend *fe)
 {
 	struct zl10353_state *state = fe->demodulator_priv;
-	char buf[52], buf2[4];
 	int ret;
 	u8 reg;
 
@@ -106,19 +105,18 @@ static void zl10353_dump_regs(struct dvb_frontend *fe)
 	for (reg = 0; ; reg++) {
 		if (reg % 16 == 0) {
 			if (reg)
-				printk(KERN_DEBUG "%s\n", buf);
-			sprintf(buf, "%02x: ", reg);
+				printk(KERN_CONT "\n");
+			printk(KERN_DEBUG "%02x:", reg);
 		}
 		ret = zl10353_read_register(state, reg);
 		if (ret >= 0)
-			sprintf(buf2, "%02x ", (u8)ret);
+			printk(KERN_CONT " %02x", (u8)ret);
 		else
-			strcpy(buf2, "-- ");
-		strcat(buf, buf2);
+			printk(KERN_CONT " --");
 		if (reg == 0xff)
 			break;
 	}
-	printk(KERN_DEBUG "%s\n", buf);
+	printk(KERN_CONT "\n");
 }
 
 static void zl10353_calc_nominal_rate(struct dvb_frontend *fe,
-- 
GitLab


From 0a6e44d1beb30813f62ad376a31694e637858328 Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Wed, 29 Jul 2009 01:39:12 -0300
Subject: [PATCH 0839/1153] V4L/DVB (12344): em28xx: fix support for Plextor
 ConvertX PX-TV100U

This device uses msp34xx and uses 2.048 MHz frequency for I2S
communication.

Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with
this device and proposing an approach for fixing the issue.

Tested-by: Angelo Cano <acano@fastmail.fm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-cards.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index bc213a1f9c1..d0b033bce86 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -622,22 +622,27 @@ struct em28xx_board em28xx_boards[] = {
 	},
 	[EM2861_BOARD_PLEXTOR_PX_TV100U] = {
 		.name         = "Plextor ConvertX PX-TV100U",
-		.valid        = EM28XX_BOARD_NOT_VALIDATED,
 		.tuner_type   = TUNER_TNF_5335MF,
+		.xclk         = EM28XX_XCLK_I2S_MSB_TIMING |
+				EM28XX_XCLK_FREQUENCY_12MHZ,
 		.tda9887_conf = TDA9887_PRESENT,
 		.decoder      = EM28XX_TVP5150,
+		.has_msp34xx  = 1,
 		.input        = { {
 			.type     = EM28XX_VMUX_TELEVISION,
 			.vmux     = TVP5150_COMPOSITE0,
 			.amux     = EM28XX_AMUX_LINE_IN,
+			.gpio     = pinnacle_hybrid_pro_analog,
 		}, {
 			.type     = EM28XX_VMUX_COMPOSITE1,
 			.vmux     = TVP5150_COMPOSITE1,
 			.amux     = EM28XX_AMUX_LINE_IN,
+			.gpio     = pinnacle_hybrid_pro_analog,
 		}, {
 			.type     = EM28XX_VMUX_SVIDEO,
 			.vmux     = TVP5150_SVIDEO,
 			.amux     = EM28XX_AMUX_LINE_IN,
+			.gpio     = pinnacle_hybrid_pro_analog,
 		} },
 	},
 
@@ -1877,9 +1882,8 @@ void em28xx_pre_card_setup(struct em28xx *dev)
 	/* request some modules */
 	switch (dev->model) {
 	case EM2861_BOARD_PLEXTOR_PX_TV100U:
-		/* FIXME guess */
-		/* Turn on analog audio output */
-		em28xx_write_reg(dev, EM28XX_R08_GPIO, 0xfd);
+		/* Sets the msp34xx I2S speed */
+		dev->i2s_speed = 2048000;
 		break;
 	case EM2861_BOARD_KWORLD_PVRTV_300U:
 	case EM2880_BOARD_KWORLD_DVB_305U:
-- 
GitLab


From 337ab6d34f0be7cfbfb5ac8cb651276fc58aa20d Mon Sep 17 00:00:00 2001
From: Sohail Syyed <linuxtv@hubstar.net>
Date: Sun, 26 Jul 2009 11:06:20 -0300
Subject: [PATCH 0840/1153] V4L/DVB (12349): cx88: HVR1300 ensure switching
 from Encoder to DVB-T and back is reliable

Current tip is broken and does not switch back to DVB-T correctly

Signed-off-by: Sohail Syyed <linuxtv@hubstar.net>
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/cx88/cx88-mpeg.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/media/video/cx88/cx88-mpeg.c b/drivers/media/video/cx88/cx88-mpeg.c
index da4e3912cd3..7172dcf2a4f 100644
--- a/drivers/media/video/cx88/cx88-mpeg.c
+++ b/drivers/media/video/cx88/cx88-mpeg.c
@@ -116,6 +116,10 @@ static int cx8802_start_dma(struct cx8802_dev    *dev,
 			udelay(100);
 			break;
 		case CX88_BOARD_HAUPPAUGE_HVR1300:
+			/* Enable MPEG parallel IO and video signal pins */
+			cx_write(MO_PINMUX_IO, 0x88);
+			cx_write(TS_SOP_STAT, 0);
+			cx_write(TS_VALERR_CNTRL, 0);
 			break;
 		case CX88_BOARD_PINNACLE_PCTV_HD_800i:
 			/* Enable MPEG parallel IO and video signal pins */
-- 
GitLab


From 6655be0f4f377d7e249219c6031c4be3533604a2 Mon Sep 17 00:00:00 2001
From: Michael Krufky <mkrufky@kernellabs.com>
Date: Mon, 20 Jul 2009 12:20:58 -0300
Subject: [PATCH 0841/1153] V4L/DVB (12362): cx23885-417: fix manipulation of
 tvnorms

Currently, the VIDIOC_S_STD ioctl just returns -EINVAL regardless of
the norm passed.  This patch sets cx23885_mpeg_template.tvnorms and
cx23885_mpeg_template.current_norm so that the VIDIOC_S_STD will work.

Thanks to Joseph Yasi for pointing this out, even though this particular
fix was already pushed into a development repository, merge priority of
this changeset has been escalated as a result of Joseph posting this
identical patch.

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Joseph A. Yasi <joe.yasi@gmail.com>
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/cx23885/cx23885-417.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/media/video/cx23885/cx23885-417.c b/drivers/media/video/cx23885/cx23885-417.c
index e0cf21e0b1b..1a1048b18f7 100644
--- a/drivers/media/video/cx23885/cx23885-417.c
+++ b/drivers/media/video/cx23885/cx23885-417.c
@@ -1715,6 +1715,8 @@ static struct video_device cx23885_mpeg_template = {
 	.fops          = &mpeg_fops,
 	.ioctl_ops     = &mpeg_ioctl_ops,
 	.minor         = -1,
+	.tvnorms       = CX23885_NORMS,
+	.current_norm  = V4L2_STD_NTSC_M,
 };
 
 void cx23885_417_unregister(struct cx23885_dev *dev)
-- 
GitLab


From ba1bc64272f0af668690ba2bf859b13172db7230 Mon Sep 17 00:00:00 2001
From: Nils Kassube <kassube@gmx.net>
Date: Tue, 28 Jul 2009 11:54:52 -0300
Subject: [PATCH 0842/1153] V4L/DVB (12371): af9015: Fix for crash in
 dvb-usb-af9015

Moving BOOT fixes problem.

Signed-off-by: Nils Kassube <kassube@gmx.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/dvb/dvb-usb/af9015.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/dvb/dvb-usb/af9015.c b/drivers/media/dvb/dvb-usb/af9015.c
index 4cb31e7c13c..26690dfb326 100644
--- a/drivers/media/dvb/dvb-usb/af9015.c
+++ b/drivers/media/dvb/dvb-usb/af9015.c
@@ -81,7 +81,6 @@ static int af9015_rw_udev(struct usb_device *udev, struct req_t *req)
 
 	switch (req->cmd) {
 	case GET_CONFIG:
-	case BOOT:
 	case READ_MEMORY:
 	case RECONNECT_USB:
 	case GET_IR_CODE:
@@ -100,6 +99,7 @@ static int af9015_rw_udev(struct usb_device *udev, struct req_t *req)
 	case WRITE_VIRTUAL_MEMORY:
 	case COPY_FIRMWARE:
 	case DOWNLOAD_FIRMWARE:
+	case BOOT:
 		break;
 	default:
 		err("unknown command:%d", req->cmd);
-- 
GitLab


From 261982f17051d10a1054a77ec8ae13517e0acee2 Mon Sep 17 00:00:00 2001
From: Brian Johnson <brijohn@gmail.com>
Date: Sun, 19 Jul 2009 15:58:56 -0300
Subject: [PATCH 0843/1153] V4L/DVB (12373a): Add gspca sn9c20x subdriver entry
 to MAINTAINERS file

MAINTAINERS |    8 ++++++++

Signed-off-by: Brian Johnson <brijohn@gmail.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 MAINTAINERS | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index b1114cfac6b..2c4326c0de9 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2238,6 +2238,14 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 S:	Maintained
 F:	drivers/media/video/gspca/pac207.c
 
+GSPCA SN9C20X SUBDRIVER
+P:	Brian Johnson
+M:	brijohn@gmail.com
+L:	linux-media@vger.kernel.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
+S:	Maintained
+F:	drivers/media/video/gspca/sn9c20x.c
+
 GSPCA T613 SUBDRIVER
 M:	Leandro Costantino <lcostantino@gmail.com>
 L:	linux-media@vger.kernel.org
-- 
GitLab


From d1ae4e1d05cc982b6b480c1a3d69b8bb231e3493 Mon Sep 17 00:00:00 2001
From: Michael Krufky <mkrufky@kernellabs.com>
Date: Sun, 12 Jul 2009 18:25:45 -0300
Subject: [PATCH 0844/1153] V4L/DVB (12374): sms1xxx: fix broken Hauppauge
 devices

The current GPIO configuration breaks all Hauppauge devices.

The code being removed affects Hauppauge devices only,
and is the cause of the breakage.

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/dvb/siano/sms-cards.c | 100 ----------------------------
 1 file changed, 100 deletions(-)

diff --git a/drivers/media/dvb/siano/sms-cards.c b/drivers/media/dvb/siano/sms-cards.c
index d8b15d583bd..76bd3cb82d9 100644
--- a/drivers/media/dvb/siano/sms-cards.c
+++ b/drivers/media/dvb/siano/sms-cards.c
@@ -124,91 +124,15 @@ int sms_board_event(struct smscore_device_t *coredev,
 
 	switch (gevent) {
 	case BOARD_EVENT_POWER_INIT: /* including hotplug */
-		switch (board_id) {
-		case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM:
-			/* set I/O and turn off all LEDs */
-			smscore_gpio_configure(coredev,
-					board->board_cfg.leds_power,
-					&MyGpioConfig);
-			smscore_gpio_set_level(coredev,
-					board->board_cfg.leds_power, 0);
-			smscore_gpio_configure(coredev, board->board_cfg.led0,
-					&MyGpioConfig);
-			smscore_gpio_set_level(coredev,
-					board->board_cfg.led0, 0);
-			smscore_gpio_configure(coredev, board->board_cfg.led1,
-					&MyGpioConfig);
-			smscore_gpio_set_level(coredev,
-					board->board_cfg.led1, 0);
-			break;
-		case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2:
-		case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD:
-			/* set I/O and turn off LNA */
-			smscore_gpio_configure(coredev,
-					board->board_cfg.foreign_lna0_ctrl,
-					&MyGpioConfig);
-			smscore_gpio_set_level(coredev,
-					board->board_cfg.foreign_lna0_ctrl,
-					0);
-			break;
-		}
 		break; /* BOARD_EVENT_BIND */
 
 	case BOARD_EVENT_POWER_SUSPEND:
-		switch (board_id) {
-		case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM:
-			smscore_gpio_set_level(coredev,
-						board->board_cfg.leds_power, 0);
-			smscore_gpio_set_level(coredev,
-						board->board_cfg.led0, 0);
-			smscore_gpio_set_level(coredev,
-						board->board_cfg.led1, 0);
-			break;
-		case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2:
-		case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD:
-			smscore_gpio_set_level(coredev,
-					board->board_cfg.foreign_lna0_ctrl,
-					0);
-			break;
-		}
 		break; /* BOARD_EVENT_POWER_SUSPEND */
 
 	case BOARD_EVENT_POWER_RESUME:
-		switch (board_id) {
-		case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM:
-			smscore_gpio_set_level(coredev,
-						board->board_cfg.leds_power, 1);
-			smscore_gpio_set_level(coredev,
-						board->board_cfg.led0, 1);
-			smscore_gpio_set_level(coredev,
-						board->board_cfg.led1, 0);
-			break;
-		case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2:
-		case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD:
-			smscore_gpio_set_level(coredev,
-					board->board_cfg.foreign_lna0_ctrl,
-					1);
-			break;
-		}
 		break; /* BOARD_EVENT_POWER_RESUME */
 
 	case BOARD_EVENT_BIND:
-		switch (board_id) {
-		case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM:
-			smscore_gpio_set_level(coredev,
-				board->board_cfg.leds_power, 1);
-			smscore_gpio_set_level(coredev,
-				board->board_cfg.led0, 1);
-			smscore_gpio_set_level(coredev,
-				board->board_cfg.led1, 0);
-			break;
-		case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD_R2:
-		case SMS1XXX_BOARD_HAUPPAUGE_TIGER_MINICARD:
-			smscore_gpio_set_level(coredev,
-					board->board_cfg.foreign_lna0_ctrl,
-					1);
-			break;
-		}
 		break; /* BOARD_EVENT_BIND */
 
 	case BOARD_EVENT_SCAN_PROG:
@@ -218,20 +142,8 @@ int sms_board_event(struct smscore_device_t *coredev,
 	case BOARD_EVENT_EMERGENCY_WARNING_SIGNAL:
 		break; /* BOARD_EVENT_EMERGENCY_WARNING_SIGNAL */
 	case BOARD_EVENT_FE_LOCK:
-		switch (board_id) {
-		case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM:
-			smscore_gpio_set_level(coredev,
-			board->board_cfg.led1, 1);
-			break;
-		}
 		break; /* BOARD_EVENT_FE_LOCK */
 	case BOARD_EVENT_FE_UNLOCK:
-		switch (board_id) {
-		case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM:
-			smscore_gpio_set_level(coredev,
-						board->board_cfg.led1, 0);
-			break;
-		}
 		break; /* BOARD_EVENT_FE_UNLOCK */
 	case BOARD_EVENT_DEMOD_LOCK:
 		break; /* BOARD_EVENT_DEMOD_LOCK */
@@ -248,20 +160,8 @@ int sms_board_event(struct smscore_device_t *coredev,
 	case BOARD_EVENT_RECEPTION_LOST_0:
 		break; /* BOARD_EVENT_RECEPTION_LOST_0 */
 	case BOARD_EVENT_MULTIPLEX_OK:
-		switch (board_id) {
-		case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM:
-			smscore_gpio_set_level(coredev,
-						board->board_cfg.led1, 1);
-			break;
-		}
 		break; /* BOARD_EVENT_MULTIPLEX_OK */
 	case BOARD_EVENT_MULTIPLEX_ERRORS:
-		switch (board_id) {
-		case SMS1XXX_BOARD_HAUPPAUGE_WINDHAM:
-			smscore_gpio_set_level(coredev,
-						board->board_cfg.led1, 0);
-			break;
-		}
 		break; /* BOARD_EVENT_MULTIPLEX_ERRORS */
 
 	default:
-- 
GitLab


From d79cd8393ae85ebaf53a8fc93491eea96522d68e Mon Sep 17 00:00:00 2001
From: Laurent Pinchart <laurent.pinchart@skynet.be>
Date: Sun, 19 Jul 2009 19:16:05 -0300
Subject: [PATCH 0845/1153] V4L/DVB (12328): uvcvideo: Don't apply the
 FIX_BANDWIDTH quirk to all ViMicro devices

Commit 50144aeeb702ea105697ae5249f059ea3990b838 broke the Samsung NC10
netbook webcam. Instead of applying the FIX_BANDWIDTH quirk to all ViMicro
devices, list the devices explicitly.

Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/uvc/uvc_driver.c | 24 +++++++++++++++++++++---
 1 file changed, 21 insertions(+), 3 deletions(-)

diff --git a/drivers/media/video/uvc/uvc_driver.c b/drivers/media/video/uvc/uvc_driver.c
index 89927b7aec2..04b47832fa0 100644
--- a/drivers/media/video/uvc/uvc_driver.c
+++ b/drivers/media/video/uvc/uvc_driver.c
@@ -1845,11 +1845,29 @@ static struct usb_device_id uvc_ids[] = {
 	  .bInterfaceSubClass	= 1,
 	  .bInterfaceProtocol	= 0,
 	  .driver_info		= UVC_QUIRK_STREAM_NO_FID },
-	/* ViMicro */
-	{ .match_flags		= USB_DEVICE_ID_MATCH_VENDOR
+	/* ViMicro Vega */
+	{ .match_flags		= USB_DEVICE_ID_MATCH_DEVICE
+				| USB_DEVICE_ID_MATCH_INT_INFO,
+	  .idVendor		= 0x0ac8,
+	  .idProduct		= 0x332d,
+	  .bInterfaceClass	= USB_CLASS_VIDEO,
+	  .bInterfaceSubClass	= 1,
+	  .bInterfaceProtocol	= 0,
+	  .driver_info		= UVC_QUIRK_FIX_BANDWIDTH },
+	/* ViMicro - Minoru3D */
+	{ .match_flags		= USB_DEVICE_ID_MATCH_DEVICE
+				| USB_DEVICE_ID_MATCH_INT_INFO,
+	  .idVendor		= 0x0ac8,
+	  .idProduct		= 0x3410,
+	  .bInterfaceClass	= USB_CLASS_VIDEO,
+	  .bInterfaceSubClass	= 1,
+	  .bInterfaceProtocol	= 0,
+	  .driver_info		= UVC_QUIRK_FIX_BANDWIDTH },
+	/* ViMicro Venus - Minoru3D */
+	{ .match_flags		= USB_DEVICE_ID_MATCH_DEVICE
 				| USB_DEVICE_ID_MATCH_INT_INFO,
 	  .idVendor		= 0x0ac8,
-	  .idProduct		= 0x0000,
+	  .idProduct		= 0x3420,
 	  .bInterfaceClass	= USB_CLASS_VIDEO,
 	  .bInterfaceSubClass	= 1,
 	  .bInterfaceProtocol	= 0,
-- 
GitLab


From bd0232c13419b7ce51e02942082ff6af231e0f84 Mon Sep 17 00:00:00 2001
From: Laurent Pinchart <laurent.pinchart@skynet.be>
Date: Sat, 1 Aug 2009 18:14:24 -0300
Subject: [PATCH 0846/1153] V4L/DVB (12380): uvcvideo: Avoid flooding the
 kernel log with "unknown event type" messages

The iSight sends non-UVC status events through the interrupt endpoint. Those
invalid events are reported to the kernel log, resulting in a log flood.

Only log the events when the UVC_TRACE_STATUS flag is set.

Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/uvc/uvc_status.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/media/video/uvc/uvc_status.c b/drivers/media/video/uvc/uvc_status.c
index f152a990386..1ca6dff7361 100644
--- a/drivers/media/video/uvc/uvc_status.c
+++ b/drivers/media/video/uvc/uvc_status.c
@@ -145,8 +145,8 @@ static void uvc_status_complete(struct urb *urb)
 			break;
 
 		default:
-			uvc_printk(KERN_INFO, "unknown event type %u.\n",
-				dev->status[0]);
+			uvc_trace(UVC_TRACE_STATUS, "Unknown status event "
+				"type %u.\n", dev->status[0]);
 			break;
 		}
 	}
-- 
GitLab


From 79a6382551507ce196c3b4296e32b5386cdfbf15 Mon Sep 17 00:00:00 2001
From: Michael Krufky <mkrufky@kernellabs.com>
Date: Sun, 2 Aug 2009 12:37:34 -0300
Subject: [PATCH 0847/1153] V4L/DVB (12386): sms1xxx: fix build warning: unused
 variable 'board'

Remove the following build warning:

sms-cards.c: In function 'sms_board_event':
sms-cards.c:120: warning: unused variable 'board'

Thanks to Hans Verkuil for pointing this out.

The problem code has been #if 0'd for now, this will likely be
used again in the future, once the event interface is complete.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/dvb/siano/sms-cards.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/media/dvb/siano/sms-cards.c b/drivers/media/dvb/siano/sms-cards.c
index 76bd3cb82d9..0420e2885e7 100644
--- a/drivers/media/dvb/siano/sms-cards.c
+++ b/drivers/media/dvb/siano/sms-cards.c
@@ -116,8 +116,6 @@ static inline void sms_gpio_assign_11xx_default_led_config(
 
 int sms_board_event(struct smscore_device_t *coredev,
 		enum SMS_BOARD_EVENTS gevent) {
-	int board_id = smscore_get_board_id(coredev);
-	struct sms_board *board = sms_get_board(board_id);
 	struct smscore_gpio_config MyGpioConfig;
 
 	sms_gpio_assign_11xx_default_led_config(&MyGpioConfig);
-- 
GitLab


From b5f05064b556da5183adc383e5f8d50af0392849 Mon Sep 17 00:00:00 2001
From: Michael Krufky <mkrufky@kernellabs.com>
Date: Mon, 3 Aug 2009 16:51:33 -0300
Subject: [PATCH 0848/1153] V4L/DVB (12390): saa7134: Use correct product name
 for Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 Documentation/video4linux/CARDLIST.saa7134  |  2 +-
 drivers/media/video/saa7134/saa7134-cards.c | 20 ++++++++++----------
 drivers/media/video/saa7134/saa7134-dvb.c   |  2 +-
 drivers/media/video/saa7134/saa7134.h       |  2 +-
 4 files changed, 13 insertions(+), 13 deletions(-)

diff --git a/Documentation/video4linux/CARDLIST.saa7134 b/Documentation/video4linux/CARDLIST.saa7134
index 15562427e8a..a82b767f9e7 100644
--- a/Documentation/video4linux/CARDLIST.saa7134
+++ b/Documentation/video4linux/CARDLIST.saa7134
@@ -153,7 +153,7 @@
 152 -> Asus Tiger Rev:1.00                      [1043:4857]
 153 -> Kworld Plus TV Analog Lite PCI           [17de:7128]
 154 -> Avermedia AVerTV GO 007 FM Plus          [1461:f31d]
-155 -> Hauppauge WinTV-HVR1120 ATSC/QAM-Hybrid  [0070:6706,0070:6708]
+155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid  [0070:6706,0070:6708]
 156 -> Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid   [0070:6707,0070:6709,0070:670a]
 157 -> Avermedia AVerTV Studio 507UA            [1461:a11b]
 158 -> AVerMedia Cardbus TV/Radio (E501R)       [1461:b7e9]
diff --git a/drivers/media/video/saa7134/saa7134-cards.c b/drivers/media/video/saa7134/saa7134-cards.c
index 06861b782b9..60e74ad5967 100644
--- a/drivers/media/video/saa7134/saa7134-cards.c
+++ b/drivers/media/video/saa7134/saa7134-cards.c
@@ -3331,8 +3331,8 @@ struct saa7134_board saa7134_boards[] = {
 			.gpio = 0x0200100,
 		},
 	},
-	[SAA7134_BOARD_HAUPPAUGE_HVR1120] = {
-		.name           = "Hauppauge WinTV-HVR1120 ATSC/QAM-Hybrid",
+	[SAA7134_BOARD_HAUPPAUGE_HVR1150] = {
+		.name           = "Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid",
 		.audio_clock    = 0x00187de7,
 		.tuner_type     = TUNER_PHILIPS_TDA8290,
 		.radio_type     = UNSET,
@@ -5862,7 +5862,7 @@ struct pci_device_id saa7134_pci_tbl[] = {
 		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
 		.subvendor    = 0x0070,
 		.subdevice    = 0x6706,
-		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1120,
+		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1150,
 	},{
 		.vendor       = PCI_VENDOR_ID_PHILIPS,
 		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
@@ -5874,7 +5874,7 @@ struct pci_device_id saa7134_pci_tbl[] = {
 		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
 		.subvendor    = 0x0070,
 		.subdevice    = 0x6708,
-		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1120,
+		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1150,
 	},{
 		.vendor       = PCI_VENDOR_ID_PHILIPS,
 		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
@@ -6363,7 +6363,7 @@ static int saa7134_tda8290_18271_callback(struct saa7134_dev *dev,
 	switch (command) {
 	case TDA18271_CALLBACK_CMD_AGC_ENABLE: /* 0 */
 		switch (dev->board) {
-		case SAA7134_BOARD_HAUPPAUGE_HVR1120:
+		case SAA7134_BOARD_HAUPPAUGE_HVR1150:
 		case SAA7134_BOARD_HAUPPAUGE_HVR1110R3:
 			ret = saa7134_tda18271_hvr11x0_toggle_agc(dev, arg);
 			break;
@@ -6384,7 +6384,7 @@ static int saa7134_tda8290_callback(struct saa7134_dev *dev,
 	int ret;
 
 	switch (dev->board) {
-	case SAA7134_BOARD_HAUPPAUGE_HVR1120:
+	case SAA7134_BOARD_HAUPPAUGE_HVR1150:
 	case SAA7134_BOARD_HAUPPAUGE_HVR1110R3:
 		/* tda8290 + tda18271 */
 		ret = saa7134_tda8290_18271_callback(dev, command, arg);
@@ -6427,7 +6427,7 @@ static void hauppauge_eeprom(struct saa7134_dev *dev, u8 *eeprom_data)
 	switch (tv.model) {
 	case 67019: /* WinTV-HVR1110 (Retail, IR Blaster, hybrid, FM, SVid/Comp, 3.5mm audio in) */
 	case 67109: /* WinTV-HVR1000 (Retail, IR Receive, analog, no FM, SVid/Comp, 3.5mm audio in) */
-	case 67201: /* WinTV-HVR1120 (Retail, IR Receive, hybrid, FM, SVid/Comp, 3.5mm audio in) */
+	case 67201: /* WinTV-HVR1150 (Retail, IR Receive, hybrid, FM, SVid/Comp, 3.5mm audio in) */
 	case 67301: /* WinTV-HVR1000 (Retail, IR Receive, analog, no FM, SVid/Comp, 3.5mm audio in) */
 	case 67209: /* WinTV-HVR1110 (Retail, IR Receive, hybrid, FM, SVid/Comp, 3.5mm audio in) */
 	case 67559: /* WinTV-HVR1110 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */
@@ -6435,7 +6435,7 @@ static void hauppauge_eeprom(struct saa7134_dev *dev, u8 *eeprom_data)
 	case 67579: /* WinTV-HVR1110 (OEM, no IR, hybrid, no FM) */
 	case 67589: /* WinTV-HVR1110 (OEM, no IR, hybrid, no FM, SVid/Comp, RCA aud) */
 	case 67599: /* WinTV-HVR1110 (OEM, no IR, hybrid, no FM, SVid/Comp, RCA aud) */
-	case 67651: /* WinTV-HVR1120 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */
+	case 67651: /* WinTV-HVR1150 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */
 	case 67659: /* WinTV-HVR1110 (OEM, no IR, hybrid, FM, SVid/Comp, RCA aud) */
 		break;
 	default:
@@ -6625,7 +6625,7 @@ int saa7134_board_init1(struct saa7134_dev *dev)
 
 		saa_writeb (SAA7134_PRODUCTION_TEST_MODE, 0x00);
 		break;
-	case SAA7134_BOARD_HAUPPAUGE_HVR1120:
+	case SAA7134_BOARD_HAUPPAUGE_HVR1150:
 	case SAA7134_BOARD_HAUPPAUGE_HVR1110R3:
 		/* GPIO 26 high for digital, low for analog */
 		saa7134_set_gpio(dev, 26, 0);
@@ -6891,7 +6891,7 @@ int saa7134_board_init2(struct saa7134_dev *dev)
 		       dev->name, saa7134_boards[dev->board].name);
 	       }
 	       break;
-	case SAA7134_BOARD_HAUPPAUGE_HVR1120:
+	case SAA7134_BOARD_HAUPPAUGE_HVR1150:
 	case SAA7134_BOARD_HAUPPAUGE_HVR1110R3:
 		hauppauge_eeprom(dev, dev->eedata+0x80);
 		break;
diff --git a/drivers/media/video/saa7134/saa7134-dvb.c b/drivers/media/video/saa7134/saa7134-dvb.c
index 31930f26ffc..ae0a7ecc46d 100644
--- a/drivers/media/video/saa7134/saa7134-dvb.c
+++ b/drivers/media/video/saa7134/saa7134-dvb.c
@@ -1147,7 +1147,7 @@ static int dvb_init(struct saa7134_dev *dev)
 					 &tda827x_cfg_1) < 0)
 			goto dettach_frontend;
 		break;
-	case SAA7134_BOARD_HAUPPAUGE_HVR1120:
+	case SAA7134_BOARD_HAUPPAUGE_HVR1150:
 		fe0->dvb.frontend = dvb_attach(lgdt3305_attach,
 					       &hcw_lgdt3305_config,
 					       &dev->i2c_adap);
diff --git a/drivers/media/video/saa7134/saa7134.h b/drivers/media/video/saa7134/saa7134.h
index 82268848f26..bad5b237f21 100644
--- a/drivers/media/video/saa7134/saa7134.h
+++ b/drivers/media/video/saa7134/saa7134.h
@@ -278,7 +278,7 @@ struct saa7134_format {
 #define SAA7134_BOARD_ASUSTeK_TIGER         152
 #define SAA7134_BOARD_KWORLD_PLUS_TV_ANALOG 153
 #define SAA7134_BOARD_AVERMEDIA_GO_007_FM_PLUS 154
-#define SAA7134_BOARD_HAUPPAUGE_HVR1120     155
+#define SAA7134_BOARD_HAUPPAUGE_HVR1150     155
 #define SAA7134_BOARD_HAUPPAUGE_HVR1110R3   156
 #define SAA7134_BOARD_AVERMEDIA_STUDIO_507UA 157
 #define SAA7134_BOARD_AVERMEDIA_CARDBUS_501 158
-- 
GitLab


From 0e316ecfc851c8dd955d9fa6e0d3a46e451a46f4 Mon Sep 17 00:00:00 2001
From: Michael Krufky <mkrufky@kernellabs.com>
Date: Mon, 3 Aug 2009 16:51:33 -0300
Subject: [PATCH 0849/1153] V4L/DVB (12391): saa7134: Use correct product name
 for Hauppauge WinTV-HVR1120 DVB-T/Hybrid

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 Documentation/video4linux/CARDLIST.saa7134  |  2 +-
 drivers/media/video/saa7134/saa7134-cards.c | 18 +++++++++---------
 drivers/media/video/saa7134/saa7134-dvb.c   |  2 +-
 drivers/media/video/saa7134/saa7134.h       |  2 +-
 4 files changed, 12 insertions(+), 12 deletions(-)

diff --git a/Documentation/video4linux/CARDLIST.saa7134 b/Documentation/video4linux/CARDLIST.saa7134
index a82b767f9e7..c913e561419 100644
--- a/Documentation/video4linux/CARDLIST.saa7134
+++ b/Documentation/video4linux/CARDLIST.saa7134
@@ -154,7 +154,7 @@
 153 -> Kworld Plus TV Analog Lite PCI           [17de:7128]
 154 -> Avermedia AVerTV GO 007 FM Plus          [1461:f31d]
 155 -> Hauppauge WinTV-HVR1150 ATSC/QAM-Hybrid  [0070:6706,0070:6708]
-156 -> Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid   [0070:6707,0070:6709,0070:670a]
+156 -> Hauppauge WinTV-HVR1120 DVB-T/Hybrid     [0070:6707,0070:6709,0070:670a]
 157 -> Avermedia AVerTV Studio 507UA            [1461:a11b]
 158 -> AVerMedia Cardbus TV/Radio (E501R)       [1461:b7e9]
 159 -> Beholder BeholdTV 505 RDS                [0000:505B]
diff --git a/drivers/media/video/saa7134/saa7134-cards.c b/drivers/media/video/saa7134/saa7134-cards.c
index 60e74ad5967..6eebe3ef97d 100644
--- a/drivers/media/video/saa7134/saa7134-cards.c
+++ b/drivers/media/video/saa7134/saa7134-cards.c
@@ -3363,8 +3363,8 @@ struct saa7134_board saa7134_boards[] = {
 			.gpio = 0x0800100, /* GPIO 23 HI for FM */
 		},
 	},
-	[SAA7134_BOARD_HAUPPAUGE_HVR1110R3] = {
-		.name           = "Hauppauge WinTV-HVR1110r3 DVB-T/Hybrid",
+	[SAA7134_BOARD_HAUPPAUGE_HVR1120] = {
+		.name           = "Hauppauge WinTV-HVR1120 DVB-T/Hybrid",
 		.audio_clock    = 0x00187de7,
 		.tuner_type     = TUNER_PHILIPS_TDA8290,
 		.radio_type     = UNSET,
@@ -5868,7 +5868,7 @@ struct pci_device_id saa7134_pci_tbl[] = {
 		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
 		.subvendor    = 0x0070,
 		.subdevice    = 0x6707,
-		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1110R3,
+		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1120,
 	},{
 		.vendor       = PCI_VENDOR_ID_PHILIPS,
 		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
@@ -5880,13 +5880,13 @@ struct pci_device_id saa7134_pci_tbl[] = {
 		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
 		.subvendor    = 0x0070,
 		.subdevice    = 0x6709,
-		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1110R3,
+		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1120,
 	},{
 		.vendor       = PCI_VENDOR_ID_PHILIPS,
 		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
 		.subvendor    = 0x0070,
 		.subdevice    = 0x670a,
-		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1110R3,
+		.driver_data  = SAA7134_BOARD_HAUPPAUGE_HVR1120,
 	},{
 		.vendor       = PCI_VENDOR_ID_PHILIPS,
 		.device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
@@ -6364,7 +6364,7 @@ static int saa7134_tda8290_18271_callback(struct saa7134_dev *dev,
 	case TDA18271_CALLBACK_CMD_AGC_ENABLE: /* 0 */
 		switch (dev->board) {
 		case SAA7134_BOARD_HAUPPAUGE_HVR1150:
-		case SAA7134_BOARD_HAUPPAUGE_HVR1110R3:
+		case SAA7134_BOARD_HAUPPAUGE_HVR1120:
 			ret = saa7134_tda18271_hvr11x0_toggle_agc(dev, arg);
 			break;
 		default:
@@ -6385,7 +6385,7 @@ static int saa7134_tda8290_callback(struct saa7134_dev *dev,
 
 	switch (dev->board) {
 	case SAA7134_BOARD_HAUPPAUGE_HVR1150:
-	case SAA7134_BOARD_HAUPPAUGE_HVR1110R3:
+	case SAA7134_BOARD_HAUPPAUGE_HVR1120:
 		/* tda8290 + tda18271 */
 		ret = saa7134_tda8290_18271_callback(dev, command, arg);
 		break;
@@ -6626,7 +6626,7 @@ int saa7134_board_init1(struct saa7134_dev *dev)
 		saa_writeb (SAA7134_PRODUCTION_TEST_MODE, 0x00);
 		break;
 	case SAA7134_BOARD_HAUPPAUGE_HVR1150:
-	case SAA7134_BOARD_HAUPPAUGE_HVR1110R3:
+	case SAA7134_BOARD_HAUPPAUGE_HVR1120:
 		/* GPIO 26 high for digital, low for analog */
 		saa7134_set_gpio(dev, 26, 0);
 		msleep(1);
@@ -6892,7 +6892,7 @@ int saa7134_board_init2(struct saa7134_dev *dev)
 	       }
 	       break;
 	case SAA7134_BOARD_HAUPPAUGE_HVR1150:
-	case SAA7134_BOARD_HAUPPAUGE_HVR1110R3:
+	case SAA7134_BOARD_HAUPPAUGE_HVR1120:
 		hauppauge_eeprom(dev, dev->eedata+0x80);
 		break;
 	case SAA7134_BOARD_HAUPPAUGE_HVR1110:
diff --git a/drivers/media/video/saa7134/saa7134-dvb.c b/drivers/media/video/saa7134/saa7134-dvb.c
index ae0a7ecc46d..98f3efd1e94 100644
--- a/drivers/media/video/saa7134/saa7134-dvb.c
+++ b/drivers/media/video/saa7134/saa7134-dvb.c
@@ -1119,7 +1119,7 @@ static int dvb_init(struct saa7134_dev *dev)
 					 &tda827x_cfg_2) < 0)
 			goto dettach_frontend;
 		break;
-	case SAA7134_BOARD_HAUPPAUGE_HVR1110R3:
+	case SAA7134_BOARD_HAUPPAUGE_HVR1120:
 		fe0->dvb.frontend = dvb_attach(tda10048_attach,
 					       &hcw_tda10048_config,
 					       &dev->i2c_adap);
diff --git a/drivers/media/video/saa7134/saa7134.h b/drivers/media/video/saa7134/saa7134.h
index bad5b237f21..fb564f14887 100644
--- a/drivers/media/video/saa7134/saa7134.h
+++ b/drivers/media/video/saa7134/saa7134.h
@@ -279,7 +279,7 @@ struct saa7134_format {
 #define SAA7134_BOARD_KWORLD_PLUS_TV_ANALOG 153
 #define SAA7134_BOARD_AVERMEDIA_GO_007_FM_PLUS 154
 #define SAA7134_BOARD_HAUPPAUGE_HVR1150     155
-#define SAA7134_BOARD_HAUPPAUGE_HVR1110R3   156
+#define SAA7134_BOARD_HAUPPAUGE_HVR1120   156
 #define SAA7134_BOARD_AVERMEDIA_STUDIO_507UA 157
 #define SAA7134_BOARD_AVERMEDIA_CARDBUS_501 158
 #define SAA7134_BOARD_BEHOLD_505RDS         159
-- 
GitLab


From 11db906983fc6e996fcd10073843bd6f1b9a96c3 Mon Sep 17 00:00:00 2001
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Date: Mon, 3 Aug 2009 22:40:16 -0300
Subject: [PATCH 0850/1153] V4L/DVB (12393): cx88: fix regression in tuning for
 Geniatech X8000 MT

The introduction of the zl10353 i2c gate control broke support for the
Geniatech board (which is not behind an i2 gate).  Add the needed parameter.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/cx88/cx88-dvb.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/media/video/cx88/cx88-dvb.c b/drivers/media/video/cx88/cx88-dvb.c
index c44e8760021..e237b507659 100644
--- a/drivers/media/video/cx88/cx88-dvb.c
+++ b/drivers/media/video/cx88/cx88-dvb.c
@@ -501,6 +501,7 @@ static struct zl10353_config cx88_pinnacle_hybrid_pctv = {
 static struct zl10353_config cx88_geniatech_x8000_mt = {
        .demod_address = (0x1e >> 1),
        .no_tuner = 1,
+       .disable_i2c_gate_ctrl = 1,
 };
 
 static struct s5h1411_config dvico_fusionhdtv7_config = {
-- 
GitLab


From 93b999239c418cf5c668fd966ac2c5c27b8180dd Mon Sep 17 00:00:00 2001
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Date: Mon, 3 Aug 2009 22:52:59 -0300
Subject: [PATCH 0851/1153] V4L/DVB (12394): cx88: Disable xc3028 power
 management for Geniatech x8000

A user discovered that the Geniatech x8000 encountered a regression when
the xc3028 power management was introduced.  The xc3028 never recovers after
setting the powerdown register, which is probably because the xc3028 reset
GPIO is not properly configured.  Since I do not have access to the hardware
and thus cannot determine the correct GPIO configuration, just disable xc3028
power management on this board, which fixes the regression.

Thanks to user "ritec" for reporting the issue and testing the fix.

Cc: rictec <rictec@netcabo.pt>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/common/tuners/tuner-xc2028.c | 4 ++--
 drivers/media/common/tuners/tuner-xc2028.h | 1 +
 drivers/media/video/cx88/cx88-cards.c      | 8 ++++++++
 3 files changed, 11 insertions(+), 2 deletions(-)

diff --git a/drivers/media/common/tuners/tuner-xc2028.c b/drivers/media/common/tuners/tuner-xc2028.c
index aa20ce8cc66..f270e605da8 100644
--- a/drivers/media/common/tuners/tuner-xc2028.c
+++ b/drivers/media/common/tuners/tuner-xc2028.c
@@ -1119,8 +1119,8 @@ static int xc2028_sleep(struct dvb_frontend *fe)
 	struct xc2028_data *priv = fe->tuner_priv;
 	int rc = 0;
 
-	/* Avoid firmware reload on slow devices */
-	if (no_poweroff)
+	/* Avoid firmware reload on slow devices or if PM disabled */
+	if (no_poweroff || priv->ctrl.disable_power_mgmt)
 		return 0;
 
 	tuner_dbg("Putting xc2028/3028 into poweroff mode.\n");
diff --git a/drivers/media/common/tuners/tuner-xc2028.h b/drivers/media/common/tuners/tuner-xc2028.h
index 19de7928a74..a90c35d50ad 100644
--- a/drivers/media/common/tuners/tuner-xc2028.h
+++ b/drivers/media/common/tuners/tuner-xc2028.h
@@ -38,6 +38,7 @@ struct xc2028_ctrl {
 	unsigned int		input1:1;
 	unsigned int		vhfbw7:1;
 	unsigned int		uhfbw8:1;
+	unsigned int		disable_power_mgmt:1;
 	unsigned int		demod;
 	enum firmware_type	type:2;
 };
diff --git a/drivers/media/video/cx88/cx88-cards.c b/drivers/media/video/cx88/cx88-cards.c
index a5cc1c1fc2d..39465301ec9 100644
--- a/drivers/media/video/cx88/cx88-cards.c
+++ b/drivers/media/video/cx88/cx88-cards.c
@@ -3003,6 +3003,14 @@ void cx88_setup_xc3028(struct cx88_core *core, struct xc2028_ctrl *ctl)
 	case CX88_BOARD_DVICO_FUSIONHDTV_5_PCI_NANO:
 		ctl->demod = XC3028_FE_OREN538;
 		break;
+	case CX88_BOARD_GENIATECH_X8000_MT:
+		/* FIXME: For this board, the xc3028 never recovers after being
+		   powered down (the reset GPIO probably is not set properly).
+		   We don't have access to the hardware so we cannot determine
+		   which GPIO is used for xc3028, so just disable power xc3028
+		   power management for now */
+		ctl->disable_power_mgmt = 1;
+		break;
 	case CX88_BOARD_WINFAST_TV2000_XP_GLOBAL:
 	case CX88_BOARD_PROLINK_PV_GLOBAL_XTREME:
 	case CX88_BOARD_PROLINK_PV_8000GT:
-- 
GitLab


From 83053f7fe3eb0b6b1634d24ede87f1daa01ae60c Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Thu, 6 Aug 2009 21:03:35 -0300
Subject: [PATCH 0852/1153] V4L/DVB (12399): mt9v011: Add support for
 controlling frame rates

Implement g_parm/s_parm ioctls. Those are used to check the current
frame rate (in fps) and to set it to a value. In practice, there are
only 15 possible different speeds, due to chip limits.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/mt9v011.c | 89 ++++++++++++++++++++++++++++++++++-
 1 file changed, 87 insertions(+), 2 deletions(-)

diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c
index c14bf47d692..8de1316a276 100644
--- a/drivers/media/video/mt9v011.c
+++ b/drivers/media/video/mt9v011.c
@@ -156,7 +156,7 @@ static void set_balance(struct v4l2_subdev *sd)
 	mt9v011_write(sd, R2D_MT9V011_RED_GAIN, red_gain);
 }
 
-static void calc_fps(struct v4l2_subdev *sd)
+static void calc_fps(struct v4l2_subdev *sd, u32 *numerator, u32 *denominator)
 {
 	struct mt9v011 *core = to_mt9v011(sd);
 	unsigned height, width, hblank, vblank, speed;
@@ -179,6 +179,51 @@ static void calc_fps(struct v4l2_subdev *sd)
 
 	v4l2_dbg(1, debug, sd, "Programmed to %u.%03u fps (%d pixel clcks)\n",
 		tmp / 1000, tmp % 1000, t_time);
+
+	if (numerator && denominator) {
+		*numerator = 1000;
+		*denominator = (u32)frames_per_ms;
+	}
+}
+
+static u16 calc_speed(struct v4l2_subdev *sd, u32 numerator, u32 denominator)
+{
+	struct mt9v011 *core = to_mt9v011(sd);
+	unsigned height, width, hblank, vblank;
+	unsigned row_time, line_time;
+	u64 t_time, speed;
+
+	/* Avoid bogus calculus */
+	if (!numerator || !denominator)
+		return 0;
+
+	height = mt9v011_read(sd, R03_MT9V011_HEIGHT);
+	width = mt9v011_read(sd, R04_MT9V011_WIDTH);
+	hblank = mt9v011_read(sd, R05_MT9V011_HBLANK);
+	vblank = mt9v011_read(sd, R06_MT9V011_VBLANK);
+
+	row_time = width + 113 + hblank;
+	line_time = height + vblank + 1;
+
+	t_time = core->xtal * ((u64)numerator);
+	/* round to the closest value */
+	t_time += denominator / 2;
+	do_div(t_time, denominator);
+
+	speed = t_time;
+	do_div(speed, row_time * line_time);
+
+	/* Avoid having a negative value for speed */
+	if (speed < 2)
+		speed = 0;
+	else
+		speed -= 2;
+
+	/* Avoid speed overflow */
+	if (speed > 15)
+		return 15;
+
+	return (u16)speed;
 }
 
 static void set_res(struct v4l2_subdev *sd)
@@ -207,7 +252,7 @@ static void set_res(struct v4l2_subdev *sd)
 	mt9v011_write(sd, R03_MT9V011_HEIGHT, core->height);
 	mt9v011_write(sd, R06_MT9V011_VBLANK, 508 - core->height);
 
-	calc_fps(sd);
+	calc_fps(sd, NULL, NULL);
 };
 
 static int mt9v011_reset(struct v4l2_subdev *sd, u32 val)
@@ -322,6 +367,44 @@ static int mt9v011_try_fmt(struct v4l2_subdev *sd, struct v4l2_format *fmt)
 	return 0;
 }
 
+static int mt9v011_g_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parms)
+{
+	struct v4l2_captureparm *cp = &parms->parm.capture;
+
+	if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	memset(cp, 0, sizeof(struct v4l2_captureparm));
+	cp->capability = V4L2_CAP_TIMEPERFRAME;
+	calc_fps(sd,
+		 &cp->timeperframe.numerator,
+		 &cp->timeperframe.denominator);
+
+	return 0;
+}
+
+static int mt9v011_s_parm(struct v4l2_subdev *sd, struct v4l2_streamparm *parms)
+{
+	struct v4l2_captureparm *cp = &parms->parm.capture;
+	struct v4l2_fract *tpf = &cp->timeperframe;
+	u16 speed;
+
+	if (parms->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+	if (cp->extendedmode != 0)
+		return -EINVAL;
+
+	speed = calc_speed(sd, tpf->numerator, tpf->denominator);
+
+	mt9v011_write(sd, R0A_MT9V011_CLK_SPEED, speed);
+	v4l2_dbg(1, debug, sd, "Setting speed to %d\n", speed);
+
+	/* Recalculate and update fps info */
+	calc_fps(sd, &tpf->numerator, &tpf->denominator);
+
+	return 0;
+}
+
 static int mt9v011_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *fmt)
 {
 	struct v4l2_pix_format *pix = &fmt->fmt.pix;
@@ -419,6 +502,8 @@ static const struct v4l2_subdev_video_ops mt9v011_video_ops = {
 	.enum_fmt = mt9v011_enum_fmt,
 	.try_fmt = mt9v011_try_fmt,
 	.s_fmt = mt9v011_s_fmt,
+	.g_parm = mt9v011_g_parm,
+	.s_parm = mt9v011_s_parm,
 };
 
 static const struct v4l2_subdev_ops mt9v011_ops = {
-- 
GitLab


From d96ecda63f41350dc93c17ccb72ea24511f207a9 Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Thu, 6 Aug 2009 21:53:59 -0300
Subject: [PATCH 0853/1153] V4L/DVB (12400): em28xx: Allow changing fps on
 webcams

em28xx doesn't have temporal scaling. However, on webcams, sensors are
capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should
be passed to the sensor for it to properly set frame rate.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-video.c | 37 +++++++++++++++++++++++
 1 file changed, 37 insertions(+)

diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c
index ff37b4c15f4..92ee9c64432 100644
--- a/drivers/media/video/em28xx/em28xx-video.c
+++ b/drivers/media/video/em28xx/em28xx-video.c
@@ -846,6 +846,41 @@ static int vidioc_s_std(struct file *file, void *priv, v4l2_std_id *norm)
 	return 0;
 }
 
+static int vidioc_g_parm(struct file *file, void *priv,
+			 struct v4l2_streamparm *p)
+{
+	struct em28xx_fh   *fh  = priv;
+	struct em28xx      *dev = fh->dev;
+	int rc = 0;
+
+	if (p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	if (dev->board.is_webcam)
+		rc = v4l2_device_call_until_err(&dev->v4l2_dev, 0,
+						video, g_parm, p);
+	else
+		v4l2_video_std_frame_period(dev->norm,
+						 &p->parm.capture.timeperframe);
+
+	return rc;
+}
+
+static int vidioc_s_parm(struct file *file, void *priv,
+			 struct v4l2_streamparm *p)
+{
+	struct em28xx_fh   *fh  = priv;
+	struct em28xx      *dev = fh->dev;
+
+	if (!dev->board.is_webcam)
+		return -EINVAL;
+
+	if (p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+		return -EINVAL;
+
+	return v4l2_device_call_until_err(&dev->v4l2_dev, 0, video, s_parm, p);
+}
+
 static const char *iname[] = {
 	[EM28XX_VMUX_COMPOSITE1] = "Composite1",
 	[EM28XX_VMUX_COMPOSITE2] = "Composite2",
@@ -1885,6 +1920,8 @@ static const struct v4l2_ioctl_ops video_ioctl_ops = {
 	.vidioc_qbuf                = vidioc_qbuf,
 	.vidioc_dqbuf               = vidioc_dqbuf,
 	.vidioc_s_std               = vidioc_s_std,
+	.vidioc_g_parm		    = vidioc_g_parm,
+	.vidioc_s_parm		    = vidioc_s_parm,
 	.vidioc_enum_input          = vidioc_enum_input,
 	.vidioc_g_input             = vidioc_g_input,
 	.vidioc_s_input             = vidioc_s_input,
-- 
GitLab


From 2526ea6e46e41322eb98ac0e9c616273402bd661 Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Fri, 7 Aug 2009 01:09:54 -0300
Subject: [PATCH 0854/1153] V4L/DVB (12401): m9v011: add vflip/hflip controls
 to control mirror/upside down

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/mt9v011.c | 53 +++++++++++++++++++++++++++++++++--
 1 file changed, 51 insertions(+), 2 deletions(-)

diff --git a/drivers/media/video/mt9v011.c b/drivers/media/video/mt9v011.c
index 8de1316a276..cc85f77a570 100644
--- a/drivers/media/video/mt9v011.c
+++ b/drivers/media/video/mt9v011.c
@@ -52,13 +52,34 @@ static struct v4l2_queryctrl mt9v011_qctrl[] = {
 		.step = 1,
 		.default_value = 0,
 		.flags = 0,
-	},
+	}, {
+		.id      = V4L2_CID_HFLIP,
+		.type    = V4L2_CTRL_TYPE_BOOLEAN,
+		.name    = "Mirror",
+		.minimum = 0,
+		.maximum = 1,
+		.step    = 1,
+		.default_value = 0,
+		.flags = 0,
+	}, {
+		.id      = V4L2_CID_VFLIP,
+		.type    = V4L2_CTRL_TYPE_BOOLEAN,
+		.name    = "Vflip",
+		.minimum = 0,
+		.maximum = 1,
+		.step    = 1,
+		.default_value = 0,
+		.flags = 0,
+	}, {
+	}
 };
 
 struct mt9v011 {
 	struct v4l2_subdev sd;
 	unsigned width, height;
 	unsigned xtal;
+	unsigned hflip:1;
+	unsigned vflip:1;
 
 	u16 global_gain, red_bal, blue_bal;
 };
@@ -131,7 +152,6 @@ static const struct i2c_reg_value mt9v011_init_default[] = {
 
 		{ R0A_MT9V011_CLK_SPEED, 0x0000 },
 		{ R1E_MT9V011_DIGITAL_ZOOM,  0x0000 },
-		{ R20_MT9V011_READ_MODE, 0x1000 },
 
 		{ R07_MT9V011_OUT_CTRL, 0x0002 },	/* chip enable */
 };
@@ -255,6 +275,20 @@ static void set_res(struct v4l2_subdev *sd)
 	calc_fps(sd, NULL, NULL);
 };
 
+static void set_read_mode(struct v4l2_subdev *sd)
+{
+	struct mt9v011 *core = to_mt9v011(sd);
+	unsigned mode = 0x1000;
+
+	if (core->hflip)
+		mode |= 0x4000;
+
+	if (core->vflip)
+		mode |= 0x8000;
+
+	mt9v011_write(sd, R20_MT9V011_READ_MODE, mode);
+}
+
 static int mt9v011_reset(struct v4l2_subdev *sd, u32 val)
 {
 	int i;
@@ -265,6 +299,7 @@ static int mt9v011_reset(struct v4l2_subdev *sd, u32 val)
 
 	set_balance(sd);
 	set_res(sd);
+	set_read_mode(sd);
 
 	return 0;
 };
@@ -285,6 +320,12 @@ static int mt9v011_g_ctrl(struct v4l2_subdev *sd, struct v4l2_control *ctrl)
 	case V4L2_CID_BLUE_BALANCE:
 		ctrl->value = core->blue_bal;
 		return 0;
+	case V4L2_CID_HFLIP:
+		ctrl->value = core->hflip ? 1 : 0;
+		return 0;
+	case V4L2_CID_VFLIP:
+		ctrl->value = core->vflip ? 1 : 0;
+		return 0;
 	}
 	return -EINVAL;
 }
@@ -333,6 +374,14 @@ static int mt9v011_s_ctrl(struct v4l2_subdev *sd, struct v4l2_control *ctrl)
 	case V4L2_CID_BLUE_BALANCE:
 		core->blue_bal = ctrl->value;
 		break;
+	case V4L2_CID_HFLIP:
+		core->hflip = ctrl->value;
+		set_read_mode(sd);
+		return 0;
+	case V4L2_CID_VFLIP:
+		core->vflip = ctrl->value;
+		set_read_mode(sd);
+		return 0;
 	default:
 		return -EINVAL;
 	}
-- 
GitLab


From 9b4e845c6cbca2bcbfdb87e4d005260604226f45 Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Fri, 7 Aug 2009 12:08:02 -0300
Subject: [PATCH 0855/1153] V4L/DVB (12402): em28xx: fix: some em2710 chips use
 a different vendor ID

Thanks to hermann pitton <hermann-pitton@arcor.de> for pointing this new
variation.

Tested-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 Documentation/video4linux/CARDLIST.em28xx | 2 +-
 drivers/media/video/em28xx/em28xx-cards.c | 2 ++
 2 files changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/video4linux/CARDLIST.em28xx b/Documentation/video4linux/CARDLIST.em28xx
index 68c236c0184..e352d754875 100644
--- a/Documentation/video4linux/CARDLIST.em28xx
+++ b/Documentation/video4linux/CARDLIST.em28xx
@@ -1,5 +1,5 @@
   0 -> Unknown EM2800 video grabber             (em2800)        [eb1a:2800]
-  1 -> Unknown EM2750/28xx video grabber        (em2820/em2840) [eb1a:2820,eb1a:2821,eb1a:2860,eb1a:2861,eb1a:2870,eb1a:2881,eb1a:2883]
+  1 -> Unknown EM2750/28xx video grabber        (em2820/em2840) [eb1a:2710,eb1a:2820,eb1a:2821,eb1a:2860,eb1a:2861,eb1a:2870,eb1a:2881,eb1a:2883]
   2 -> Terratec Cinergy 250 USB                 (em2820/em2840) [0ccd:0036]
   3 -> Pinnacle PCTV USB 2                      (em2820/em2840) [2304:0208]
   4 -> Hauppauge WinTV USB 2                    (em2820/em2840) [2040:4200,2040:4201]
diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index d0b033bce86..6c35d789cd7 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -1549,6 +1549,8 @@ struct usb_device_id em28xx_id_table[] = {
 			.driver_info = EM2750_BOARD_UNKNOWN },
 	{ USB_DEVICE(0xeb1a, 0x2800),
 			.driver_info = EM2800_BOARD_UNKNOWN },
+	{ USB_DEVICE(0xeb1a, 0x2710),
+			.driver_info = EM2820_BOARD_UNKNOWN },
 	{ USB_DEVICE(0xeb1a, 0x2820),
 			.driver_info = EM2820_BOARD_UNKNOWN },
 	{ USB_DEVICE(0xeb1a, 0x2821),
-- 
GitLab


From d594317bdc716ccd8c8cf711e3827f9b6e0b766b Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Fri, 7 Aug 2009 12:13:31 -0300
Subject: [PATCH 0856/1153] V4L/DVB (12403): em28xx: properly reports some
 em2710 chips

As reported by hermann pitton <hermann-pitton@arcor.de>, some devices
has a different chip id for em2710 (likely the older ones):

em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0)
em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22)
em28xx #0: em28xx chip ID = 17

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-cards.c | 5 ++++-
 drivers/media/video/em28xx/em28xx-reg.h   | 3 ++-
 2 files changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index 6c35d789cd7..c9e420e8a61 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -1840,11 +1840,14 @@ void em28xx_pre_card_setup(struct em28xx *dev)
 		dev->chip_id = rc;
 
 		switch (dev->chip_id) {
+		case CHIP_ID_EM2710:
+			em28xx_info("chip ID is em2710\n");
+			break;
 		case CHIP_ID_EM2750:
 			em28xx_info("chip ID is em2750\n");
 			break;
 		case CHIP_ID_EM2820:
-			em28xx_info("chip ID is em2710 or em2820\n");
+			em28xx_info("chip ID is em2820 (or em2710)\n");
 			break;
 		case CHIP_ID_EM2840:
 			em28xx_info("chip ID is em2840\n");
diff --git a/drivers/media/video/em28xx/em28xx-reg.h b/drivers/media/video/em28xx/em28xx-reg.h
index a2676d63cfd..6bf84bd787d 100644
--- a/drivers/media/video/em28xx/em28xx-reg.h
+++ b/drivers/media/video/em28xx/em28xx-reg.h
@@ -176,7 +176,8 @@
 
 /* FIXME: Need to be populated with the other chip ID's */
 enum em28xx_chip_id {
-	CHIP_ID_EM2820 = 18,	/* Also used by em2710 */
+	CHIP_ID_EM2710 = 17,
+	CHIP_ID_EM2820 = 18,	/* Also used by some em2710 */
 	CHIP_ID_EM2840 = 20,
 	CHIP_ID_EM2750 = 33,
 	CHIP_ID_EM2860 = 34,
-- 
GitLab


From c2a6b54a9cf08d4ffeb75d70603c4a5d03ac97ad Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Sat, 8 Aug 2009 03:14:55 -0300
Subject: [PATCH 0857/1153] V4L/DVB (12406): em28xx: fix: don't do image
 interlacing on webcams

Due to historical reasons, em28xx driver gets two consecutive frames and
fold them into an unique framing, doing interlacing. While this works
fine for TV images, this produces two bad effects with webcams:

1) webcam images are progressive. Merging two consecutive images produce
interlacing artifacts on the image;

2) since the driver needs to get two frames, it reduces the maximum
frame rate by two.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-cards.c |  4 +++
 drivers/media/video/em28xx/em28xx-core.c  |  5 ++-
 drivers/media/video/em28xx/em28xx-video.c | 40 ++++++++++++++++++-----
 drivers/media/video/em28xx/em28xx.h       |  3 ++
 4 files changed, 42 insertions(+), 10 deletions(-)

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index c9e420e8a61..9011a498e5b 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -2502,6 +2502,10 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev,
 		if (em28xx_hint_sensor(dev) < 0)
 			dev->board.is_webcam = 0;
 
+	/* It makes no sense to use de-interlacing mode on webcams */
+	if (dev->board.is_webcam)
+		dev->progressive = 1;
+
 	/* Do board specific init and eeprom reading */
 	em28xx_card_setup(dev);
 
diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c
index 5b78e199abd..339fffdf6bc 100644
--- a/drivers/media/video/em28xx/em28xx-core.c
+++ b/drivers/media/video/em28xx/em28xx-core.c
@@ -720,7 +720,10 @@ int em28xx_resolution_set(struct em28xx *dev)
 {
 	int width, height;
 	width = norm_maxw(dev);
-	height = norm_maxh(dev) >> 1;
+	height = norm_maxh(dev);
+
+	if (!dev->progressive)
+		height >>= norm_maxh(dev);
 
 	em28xx_set_outfmt(dev);
 
diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c
index 92ee9c64432..ab079d9256c 100644
--- a/drivers/media/video/em28xx/em28xx-video.c
+++ b/drivers/media/video/em28xx/em28xx-video.c
@@ -194,15 +194,24 @@ static void em28xx_copy_video(struct em28xx *dev,
 	startread = p;
 	remain = len;
 
-	/* Interlaces frame */
-	if (buf->top_field)
+	if (dev->progressive)
 		fieldstart = outp;
-	else
-		fieldstart = outp + bytesperline;
+	else {
+		/* Interlaces two half frames */
+		if (buf->top_field)
+			fieldstart = outp;
+		else
+			fieldstart = outp + bytesperline;
+	}
 
 	linesdone = dma_q->pos / bytesperline;
 	currlinedone = dma_q->pos % bytesperline;
-	offset = linesdone * bytesperline * 2 + currlinedone;
+
+	if (dev->progressive)
+		offset = linesdone * bytesperline + currlinedone;
+	else
+		offset = linesdone * bytesperline * 2 + currlinedone;
+
 	startwrite = fieldstart + offset;
 	lencopy = bytesperline - currlinedone;
 	lencopy = lencopy > remain ? remain : lencopy;
@@ -376,7 +385,7 @@ static inline int em28xx_isoc_copy(struct em28xx *dev, struct urb *urb)
 			em28xx_isocdbg("Video frame %d, length=%i, %s\n", p[2],
 				       len, (p[2] & 1) ? "odd" : "even");
 
-			if (!(p[2] & 1)) {
+			if (dev->progressive || !(p[2] & 1)) {
 				if (buf != NULL)
 					buffer_filled(dev, dma_q, buf);
 				get_next_buf(dma_q, &buf);
@@ -689,7 +698,10 @@ static int vidioc_g_fmt_vid_cap(struct file *file, void *priv,
 	f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M;
 
 	/* FIXME: TOP? NONE? BOTTOM? ALTENATE? */
-	f->fmt.pix.field = dev->interlaced ?
+	if (dev->progressive)
+		f->fmt.pix.field = V4L2_FIELD_NONE;
+	else
+		f->fmt.pix.field = dev->interlaced ?
 			   V4L2_FIELD_INTERLACED : V4L2_FIELD_TOP;
 
 	mutex_unlock(&dev->lock);
@@ -753,7 +765,11 @@ static int vidioc_try_fmt_vid_cap(struct file *file, void *priv,
 	f->fmt.pix.bytesperline = (dev->width * fmt->depth + 7) >> 3;
 	f->fmt.pix.sizeimage = f->fmt.pix.bytesperline * height;
 	f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M;
-	f->fmt.pix.field = V4L2_FIELD_INTERLACED;
+	if (dev->progressive)
+		f->fmt.pix.field = V4L2_FIELD_NONE;
+	else
+		f->fmt.pix.field = dev->interlaced ?
+			   V4L2_FIELD_INTERLACED : V4L2_FIELD_TOP;
 
 	return 0;
 }
@@ -1659,6 +1675,7 @@ static int em28xx_v4l2_open(struct file *filp)
 	struct em28xx *dev;
 	enum v4l2_buf_type fh_type;
 	struct em28xx_fh *fh;
+	enum v4l2_field field;
 
 	dev = em28xx_get_device(minor, &fh_type, &radio);
 
@@ -1700,8 +1717,13 @@ static int em28xx_v4l2_open(struct file *filp)
 
 	dev->users++;
 
+	if (dev->progressive)
+		field = V4L2_FIELD_NONE;
+	else
+		field = V4L2_FIELD_INTERLACED;
+
 	videobuf_queue_vmalloc_init(&fh->vb_vidq, &em28xx_video_qops,
-			NULL, &dev->slock, fh->type, V4L2_FIELD_INTERLACED,
+			NULL, &dev->slock, fh->type, field,
 			sizeof(struct em28xx_buffer), fh);
 
 	mutex_unlock(&dev->lock);
diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h
index 45bd513f62d..8c2dc38bca9 100644
--- a/drivers/media/video/em28xx/em28xx.h
+++ b/drivers/media/video/em28xx/em28xx.h
@@ -484,6 +484,9 @@ struct em28xx {
 	int sensor_xres, sensor_yres;
 	int sensor_xtal;
 
+	/* Allows progressive (e. g. non-interlaced) mode */
+	int progressive;
+
 	/* Vinmode/Vinctl used at the driver */
 	int vinmode, vinctl;
 
-- 
GitLab


From 970cff36c0850e8193ac1162e42c7c11001b872d Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Sat, 8 Aug 2009 03:28:41 -0300
Subject: [PATCH 0858/1153] V4L/DVB (12407): em28xx: Adjust Silvercrest xtal
 frequency

We don't know the xtal frequency of Silvercrest, but we need to have
some value in order to allow controlling the frame rate frequency. The
value is probably still wrong, since the manufacturer announces this
device as being capable of 30fps, but the maximum we can get is
13.5 fps.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-cards.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index 9011a498e5b..fc46032bfe2 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -1785,7 +1785,7 @@ static int em28xx_hint_sensor(struct em28xx *dev)
 		dev->em28xx_sensor = EM28XX_MT9V011;
 		dev->sensor_xres = 640;
 		dev->sensor_yres = 480;
-		dev->sensor_xtal = 6300000;
+		dev->sensor_xtal = 12150000;
 
 		/* probably means GRGB 16 bit bayer */
 		dev->vinmode = 0x0d;
-- 
GitLab


From fcd20e3c369caf7a3fec300c9c183b25a06e21b2 Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Mon, 10 Aug 2009 02:57:57 -0300
Subject: [PATCH 0859/1153] V4L/DVB (12410): em28xx: Move the non-board
 dependent part to be outside em28xx_pre_card_setup()

em28xx_pre_card_setup() is meant to contain board-specific initialization. Also,
as autodetection sometimes occur only after having i2c bus enabled, this
function may need to be called later.

Moving those setups to happen outside the function avoids calling it twice without
need and without duplicating output lines at dmesg.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-cards.c | 111 +++++++++++-----------
 1 file changed, 53 insertions(+), 58 deletions(-)

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index fc46032bfe2..6b2b5d3e2fa 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -1821,63 +1821,6 @@ static int em28xx_hint_sensor(struct em28xx *dev)
  */
 void em28xx_pre_card_setup(struct em28xx *dev)
 {
-	int rc;
-
-	em28xx_set_model(dev);
-
-	em28xx_info("Identified as %s (card=%d)\n",
-		    dev->board.name, dev->model);
-
-	/* Set the default GPO/GPIO for legacy devices */
-	dev->reg_gpo_num = EM2880_R04_GPO;
-	dev->reg_gpio_num = EM28XX_R08_GPIO;
-
-	dev->wait_after_write = 5;
-
-	/* Based on the Chip ID, set the device configuration */
-	rc = em28xx_read_reg(dev, EM28XX_R0A_CHIPID);
-	if (rc > 0) {
-		dev->chip_id = rc;
-
-		switch (dev->chip_id) {
-		case CHIP_ID_EM2710:
-			em28xx_info("chip ID is em2710\n");
-			break;
-		case CHIP_ID_EM2750:
-			em28xx_info("chip ID is em2750\n");
-			break;
-		case CHIP_ID_EM2820:
-			em28xx_info("chip ID is em2820 (or em2710)\n");
-			break;
-		case CHIP_ID_EM2840:
-			em28xx_info("chip ID is em2840\n");
-			break;
-		case CHIP_ID_EM2860:
-			em28xx_info("chip ID is em2860\n");
-			break;
-		case CHIP_ID_EM2870:
-			em28xx_info("chip ID is em2870\n");
-			dev->wait_after_write = 0;
-			break;
-		case CHIP_ID_EM2874:
-			em28xx_info("chip ID is em2874\n");
-			dev->reg_gpio_num = EM2874_R80_GPIO;
-			dev->wait_after_write = 0;
-			break;
-		case CHIP_ID_EM2883:
-			em28xx_info("chip ID is em2882/em2883\n");
-			dev->wait_after_write = 0;
-			break;
-		default:
-			em28xx_info("em28xx chip ID = %d\n", dev->chip_id);
-		}
-	}
-
-	/* Prepopulate cached GPO register content */
-	rc = em28xx_read_reg(dev, dev->reg_gpo_num);
-	if (rc >= 0)
-		dev->reg_gpo = rc;
-
 	/* Set the initial XCLK and I2C clock values based on the board
 	   definition */
 	em28xx_write_reg(dev, EM28XX_R0F_XCLK, dev->board.xclk & 0x7f);
@@ -2443,7 +2386,7 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev,
 			   int minor)
 {
 	struct em28xx *dev = *devhandle;
-	int retval = -ENOMEM;
+	int retval;
 	int errCode;
 
 	dev->udev = udev;
@@ -2460,6 +2403,58 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev,
 	dev->em28xx_read_reg_req = em28xx_read_reg_req;
 	dev->board.is_em2800 = em28xx_boards[dev->model].is_em2800;
 
+	em28xx_set_model(dev);
+
+	/* Set the default GPO/GPIO for legacy devices */
+	dev->reg_gpo_num = EM2880_R04_GPO;
+	dev->reg_gpio_num = EM28XX_R08_GPIO;
+
+	dev->wait_after_write = 5;
+
+	/* Based on the Chip ID, set the device configuration */
+	retval = em28xx_read_reg(dev, EM28XX_R0A_CHIPID);
+	if (retval > 0) {
+		dev->chip_id = retval;
+
+		switch (dev->chip_id) {
+		case CHIP_ID_EM2710:
+			em28xx_info("chip ID is em2710\n");
+			break;
+		case CHIP_ID_EM2750:
+			em28xx_info("chip ID is em2750\n");
+			break;
+		case CHIP_ID_EM2820:
+			em28xx_info("chip ID is em2820 (or em2710)\n");
+			break;
+		case CHIP_ID_EM2840:
+			em28xx_info("chip ID is em2840\n");
+			break;
+		case CHIP_ID_EM2860:
+			em28xx_info("chip ID is em2860\n");
+			break;
+		case CHIP_ID_EM2870:
+			em28xx_info("chip ID is em2870\n");
+			dev->wait_after_write = 0;
+			break;
+		case CHIP_ID_EM2874:
+			em28xx_info("chip ID is em2874\n");
+			dev->reg_gpio_num = EM2874_R80_GPIO;
+			dev->wait_after_write = 0;
+			break;
+		case CHIP_ID_EM2883:
+			em28xx_info("chip ID is em2882/em2883\n");
+			dev->wait_after_write = 0;
+			break;
+		default:
+			em28xx_info("em28xx chip ID = %d\n", dev->chip_id);
+		}
+	}
+
+	/* Prepopulate cached GPO register content */
+	retval = em28xx_read_reg(dev, dev->reg_gpo_num);
+	if (retval >= 0)
+		dev->reg_gpo = retval;
+
 	em28xx_pre_card_setup(dev);
 
 	if (!dev->board.is_em2800) {
-- 
GitLab


From 3d3215c4e4cfca74e5805a8506d50a6752172e81 Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Mon, 10 Aug 2009 10:29:27 -0300
Subject: [PATCH 0860/1153] V4L/DVB (12411): em28xx: Fix artifacts with
 Silvercrest webcam

Silvercrest mt9v011 sensor produces a 640x480 image. However,
previously, the code were getting only half of the lines and merging two
consecutive frames to "produce" a 640x480 image.

With the addition of progressive mode, now em28xx is working with a full
image. However, when the number of lines is bigger than 240, the
beginning of some odd lines are filled with blank.

After lots of testing, and physically checking the device for a Xtal, it
was noticed experimentally that mt9v011 is using em28xx XCLK as its
clock. Due to that, changing XCLK value changes the maximum speed of the
stream.

At the tests, it were possible to produce up to 32 fps, using a 30 MHz
XCLK. However, at that rate, the artifacts happen even at 320x240. Lower
values of XCLK produces artifacts only at 640x480.

At some values of xclk (for example XCLKK = 6 MHz, 640x480), it is
possible to see an invalid sucession of artifacts with this pattern:

.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

(where the dots represent the blanked pixels)

So, it seems that a waveform in the format of a ramp is interferring at
the image.

The cause of this interference is currently unknown. Some possibilities
are:
	- electrical interference (maybe this device is broken?);
	- some issue at mt9v011 programming;
	- some bug at em28xx chip.

So, for now, let's be conservative and use a value of XCLK that we know
for sure that it won't cause artifacts.

As I'm waiting for more of such devices with different em28xx chipset
revisions, I'll have the opportunity to double check the issue with
other pieces of hardware.

Later patches can vary XCLK depending on the vertical resolutions, if a
proper fix is not discovered.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-cards.c | 50 +++++++++++++++--------
 1 file changed, 34 insertions(+), 16 deletions(-)

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index 6b2b5d3e2fa..54429b629b2 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -218,7 +218,7 @@ static struct em28xx_reg_seq silvercrest_reg_seq[] = {
 struct em28xx_board em28xx_boards[] = {
 	[EM2750_BOARD_UNKNOWN] = {
 		.name          = "EM2710/EM2750/EM2751 webcam grabber",
-		.xclk          = EM28XX_XCLK_FREQUENCY_48MHZ,
+		.xclk          = EM28XX_XCLK_FREQUENCY_20MHZ,
 		.tuner_type    = TUNER_ABSENT,
 		.is_webcam     = 1,
 		.input         = { {
@@ -1768,6 +1768,7 @@ static int em28xx_hint_sensor(struct em28xx *dev)
 	__be16 version_be;
 	u16 version;
 
+	/* Micron sensor detection */
 	dev->i2c_client.addr = 0xba >> 1;
 	cmd = 0;
 	i2c_master_send(&dev->i2c_client, &cmd, 1);
@@ -1776,16 +1777,27 @@ static int em28xx_hint_sensor(struct em28xx *dev)
 		return -EINVAL;
 
 	version = be16_to_cpu(version_be);
-
 	switch (version) {
 	case 0x8232:		/* mt9v011 640x480 1.3 Mpix sensor */
 	case 0x8243:		/* mt9v011 rev B 640x480 1.3 Mpix sensor */
 		dev->model = EM2820_BOARD_SILVERCREST_WEBCAM;
+		em28xx_set_model(dev);
+
 		sensor_name = "mt9v011";
 		dev->em28xx_sensor = EM28XX_MT9V011;
 		dev->sensor_xres = 640;
 		dev->sensor_yres = 480;
-		dev->sensor_xtal = 12150000;
+		/*
+		 * FIXME: mt9v011 uses I2S speed as xtal clk - at least with
+		 * the Silvercrest cam I have here for testing - for higher
+		 * resolutions, a high clock cause horizontal artifacts, so we
+		 * need to use a lower xclk frequency.
+		 * Yet, it would be possible to adjust xclk depending on the
+		 * desired resolution, since this affects directly the
+		 * frame rate.
+		 */
+		dev->board.xclk = EM28XX_XCLK_FREQUENCY_4_3MHZ;
+		dev->sensor_xtal = 4300000;
 
 		/* probably means GRGB 16 bit bayer */
 		dev->vinmode = 0x0d;
@@ -1794,6 +1806,8 @@ static int em28xx_hint_sensor(struct em28xx *dev)
 		break;
 	case 0x8431:
 		dev->model = EM2750_BOARD_UNKNOWN;
+		em28xx_set_model(dev);
+
 		sensor_name = "mt9m001";
 		dev->em28xx_sensor = EM28XX_MT9M001;
 		em28xx_initialize_mt9m001(dev);
@@ -1810,6 +1824,9 @@ static int em28xx_hint_sensor(struct em28xx *dev)
 		return -EINVAL;
 	}
 
+	/* Setup webcam defaults */
+	em28xx_pre_card_setup(dev);
+
 	em28xx_errdev("Sensor is %s, using model %s entry.\n",
 		      sensor_name, em28xx_boards[dev->model].name);
 
@@ -2169,7 +2186,20 @@ void em28xx_register_i2c_ir(struct em28xx *dev)
 
 void em28xx_card_setup(struct em28xx *dev)
 {
-	em28xx_set_model(dev);
+	/*
+	 * If the device can be a webcam, seek for a sensor.
+	 * If sensor is not found, then it isn't a webcam.
+	 */
+	if (dev->board.is_webcam) {
+		if (em28xx_hint_sensor(dev) < 0)
+			dev->board.is_webcam = 0;
+		else
+			dev->progressive = 1;
+	} else
+		em28xx_set_model(dev);
+
+	em28xx_info("Identified as %s (card=%d)\n",
+		    dev->board.name, dev->model);
 
 	dev->tuner_type = em28xx_boards[dev->model].tuner_type;
 	if (em28xx_boards[dev->model].tuner_addr)
@@ -2489,18 +2519,6 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev,
 	dev->vinmode = 0x10;
 	dev->vinctl  = 0x11;
 
-	/*
-	 * If the device can be a webcam, seek for a sensor.
-	 * If sensor is not found, then it isn't a webcam.
-	 */
-	if (dev->board.is_webcam)
-		if (em28xx_hint_sensor(dev) < 0)
-			dev->board.is_webcam = 0;
-
-	/* It makes no sense to use de-interlacing mode on webcams */
-	if (dev->board.is_webcam)
-		dev->progressive = 1;
-
 	/* Do board specific init and eeprom reading */
 	em28xx_card_setup(dev);
 
-- 
GitLab


From d7612c86d099939503c2f849a523dbca753d1935 Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Fri, 7 Aug 2009 18:43:00 -0300
Subject: [PATCH 0861/1153] V4L/DVB (12405): em28xx-cards: move register 0x13
 setting to the proper place

Register 0x13 seems to be a sort of image control, maybe gamma, white
level or black level. Lower values produce better images, while higher
values increases the contrast and shifts colors to green. 0xff produces
a black image. This register is not Silvercrest-specific, so its code
should be moved to a better place.

If this register is left alone, a random value can be found at the
register, producing weird results.

While here, let's remove register 0x0d, as it had no noticed effect at
the image.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-cards.c | 4 ----
 drivers/media/video/em28xx/em28xx-core.c  | 3 +++
 2 files changed, 3 insertions(+), 4 deletions(-)

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index 54429b629b2..ed281f56594 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -2273,10 +2273,6 @@ void em28xx_card_setup(struct em28xx *dev)
 		em28xx_gpio_set(dev, dev->board.tuner_gpio);
 		em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
 		break;
-	case EM2820_BOARD_SILVERCREST_WEBCAM:
-		/* FIXME: need to document the registers bellow */
-		em28xx_write_reg(dev, 0x0d, 0x42);
-		em28xx_write_reg(dev, 0x13, 0x08);
 	}
 
 	if (dev->board.has_snapshot_button)
diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c
index 339fffdf6bc..98e140b5d95 100644
--- a/drivers/media/video/em28xx/em28xx-core.c
+++ b/drivers/media/video/em28xx/em28xx-core.c
@@ -632,6 +632,9 @@ int em28xx_capture_start(struct em28xx *dev, int start)
 		return rc;
 	}
 
+	if (dev->board.is_webcam)
+		rc = em28xx_write_reg(dev, 0x13, 0x0c);
+
 	/* enable video capture */
 	rc = em28xx_write_reg(dev, 0x48, 0x00);
 
-- 
GitLab


From 7d2e2e35fb50f381c9398e481aac1e1729765ae3 Mon Sep 17 00:00:00 2001
From: Randy Dunlap <randy.dunlap@oracle.com>
Date: Wed, 5 Aug 2009 12:58:47 -0300
Subject: [PATCH 0862/1153] V4L/DVB (12422): media/zr364xx: fix build errors

Fix build errors in zr364xx by adding selects:

zr364xx.c:(.text+0x195ed7): undefined reference to `videobuf_streamon'
zr364xx.c:(.text+0x196030): undefined reference to `videobuf_dqbuf'
zr364xx.c:(.text+0x1960c4): undefined reference to `videobuf_qbuf'
zr364xx.c:(.text+0x196123): undefined reference to `videobuf_querybuf'
zr364xx.c:(.text+0x196182): undefined reference to `videobuf_reqbufs'
zr364xx.c:(.text+0x196224): undefined reference to `videobuf_queue_is_busy'
zr364xx.c:(.text+0x196390): undefined reference to `videobuf_vmalloc_free'
zr364xx.c:(.text+0x196571): undefined reference to `videobuf_iolock'
zr364xx.c:(.text+0x196678): undefined reference to `videobuf_mmap_mapper'
zr364xx.c:(.text+0x196760): undefined reference to `videobuf_poll_stream'
zr364xx.c:(.text+0x19689a): undefined reference to `videobuf_read_one'
zr364xx.c:(.text+0x1969ec): undefined reference to `videobuf_mmap_free'
zr364xx.c:(.text+0x197862): undefined reference to `videobuf_queue_vmalloc_init'
zr364xx.c:(.text+0x197a28): undefined reference to `videobuf_streamoff'
zr364xx.c:(.text+0x198203): undefined reference to `videobuf_to_vmalloc'
zr364xx.c:(.text+0x198603): undefined reference to `videobuf_streamoff'
drivers/built-in.o: In function `free_buffer':
zr364xx.c:(.text+0x19930c): undefined reference to `videobuf_vmalloc_free'
drivers/built-in.o: In function `zr364xx_open':
zr364xx.c:(.text+0x19a7de): undefined reference to `videobuf_queue_vmalloc_init'
drivers/built-in.o: In function `read_pipe_completion':
zr364xx.c:(.text+0x19b17f): undefined reference to `videobuf_to_vmalloc'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/Kconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig
index 84b6fc15519..dcf9fa9264b 100644
--- a/drivers/media/video/Kconfig
+++ b/drivers/media/video/Kconfig
@@ -920,6 +920,8 @@ source "drivers/media/video/pwc/Kconfig"
 config USB_ZR364XX
 	tristate "USB ZR364XX Camera support"
 	depends on VIDEO_V4L2
+	select VIDEOBUF_GEN
+	select VIDEOBUF_VMALLOC
 	---help---
 	  Say Y here if you want to connect this type of camera to your
 	  computer's USB port.
-- 
GitLab


From 2dd54a54c19d0e5b50f4e1c591653772ead9d4a1 Mon Sep 17 00:00:00 2001
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Date: Wed, 5 Aug 2009 20:06:31 -0300
Subject: [PATCH 0863/1153] V4L/DVB (12424): soc-camera: fix recursive locking
 in .buf_queue()

The .buf_queue() V4L2 driver method is called under
spinlock_irqsave(q->irqlock,...), don't take the lock again inside the
function.

Reported-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/mx1_camera.c           |  6 +-----
 drivers/media/video/mx3_camera.c           | 19 ++++++++++---------
 drivers/media/video/pxa_camera.c           |  6 +-----
 drivers/media/video/sh_mobile_ceu_camera.c |  5 +----
 4 files changed, 13 insertions(+), 23 deletions(-)

diff --git a/drivers/media/video/mx1_camera.c b/drivers/media/video/mx1_camera.c
index 2d075205bdf..736c31d2319 100644
--- a/drivers/media/video/mx1_camera.c
+++ b/drivers/media/video/mx1_camera.c
@@ -234,6 +234,7 @@ static int mx1_camera_setup_dma(struct mx1_camera_dev *pcdev)
 	return ret;
 }
 
+/* Called under spinlock_irqsave(&pcdev->lock, ...) */
 static void mx1_videobuf_queue(struct videobuf_queue *vq,
 						struct videobuf_buffer *vb)
 {
@@ -241,13 +242,10 @@ static void mx1_videobuf_queue(struct videobuf_queue *vq,
 	struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
 	struct mx1_camera_dev *pcdev = ici->priv;
 	struct mx1_buffer *buf = container_of(vb, struct mx1_buffer, vb);
-	unsigned long flags;
 
 	dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__,
 		vb, vb->baddr, vb->bsize);
 
-	spin_lock_irqsave(&pcdev->lock, flags);
-
 	list_add_tail(&vb->queue, &pcdev->capture);
 
 	vb->state = VIDEOBUF_ACTIVE;
@@ -264,8 +262,6 @@ static void mx1_videobuf_queue(struct videobuf_queue *vq,
 			__raw_writel(temp, pcdev->base + CSICR1);
 		}
 	}
-
-	spin_unlock_irqrestore(&pcdev->lock, flags);
 }
 
 static void mx1_videobuf_release(struct videobuf_queue *vq,
diff --git a/drivers/media/video/mx3_camera.c b/drivers/media/video/mx3_camera.c
index e605c076ed8..9770cb7932c 100644
--- a/drivers/media/video/mx3_camera.c
+++ b/drivers/media/video/mx3_camera.c
@@ -332,7 +332,10 @@ static enum pixel_fmt fourcc_to_ipu_pix(__u32 fourcc)
 	}
 }
 
-/* Called with .vb_lock held */
+/*
+ * Called with .vb_lock mutex held and
+ * under spinlock_irqsave(&mx3_cam->lock, ...)
+ */
 static void mx3_videobuf_queue(struct videobuf_queue *vq,
 			       struct videobuf_buffer *vb)
 {
@@ -346,7 +349,8 @@ static void mx3_videobuf_queue(struct videobuf_queue *vq,
 	struct idmac_video_param *video = &ichan->params.video;
 	const struct soc_camera_data_format *data_fmt = icd->current_fmt;
 	dma_cookie_t cookie;
-	unsigned long flags;
+
+	BUG_ON(!irqs_disabled());
 
 	/* This is the configuration of one sg-element */
 	video->out_pixel_fmt	= fourcc_to_ipu_pix(data_fmt->fourcc);
@@ -359,8 +363,6 @@ static void mx3_videobuf_queue(struct videobuf_queue *vq,
 	memset((void *)vb->baddr, 0xaa, vb->bsize);
 #endif
 
-	spin_lock_irqsave(&mx3_cam->lock, flags);
-
 	list_add_tail(&vb->queue, &mx3_cam->capture);
 
 	if (!mx3_cam->active) {
@@ -370,24 +372,23 @@ static void mx3_videobuf_queue(struct videobuf_queue *vq,
 		vb->state = VIDEOBUF_QUEUED;
 	}
 
-	spin_unlock_irqrestore(&mx3_cam->lock, flags);
+	spin_unlock_irq(&mx3_cam->lock);
 
 	cookie = txd->tx_submit(txd);
 	dev_dbg(&icd->dev, "Submitted cookie %d DMA 0x%08x\n", cookie, sg_dma_address(&buf->sg));
+
+	spin_lock_irq(&mx3_cam->lock);
+
 	if (cookie >= 0)
 		return;
 
 	/* Submit error */
 	vb->state = VIDEOBUF_PREPARED;
 
-	spin_lock_irqsave(&mx3_cam->lock, flags);
-
 	list_del_init(&vb->queue);
 
 	if (mx3_cam->active == buf)
 		mx3_cam->active = NULL;
-
-	spin_unlock_irqrestore(&mx3_cam->lock, flags);
 }
 
 /* Called with .vb_lock held */
diff --git a/drivers/media/video/pxa_camera.c b/drivers/media/video/pxa_camera.c
index e048d25798c..016bb45ba0c 100644
--- a/drivers/media/video/pxa_camera.c
+++ b/drivers/media/video/pxa_camera.c
@@ -612,6 +612,7 @@ static void pxa_camera_stop_capture(struct pxa_camera_dev *pcdev)
 	dev_dbg(pcdev->soc_host.dev, "%s\n", __func__);
 }
 
+/* Called under spinlock_irqsave(&pcdev->lock, ...) */
 static void pxa_videobuf_queue(struct videobuf_queue *vq,
 			       struct videobuf_buffer *vb)
 {
@@ -619,13 +620,10 @@ static void pxa_videobuf_queue(struct videobuf_queue *vq,
 	struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
 	struct pxa_camera_dev *pcdev = ici->priv;
 	struct pxa_buffer *buf = container_of(vb, struct pxa_buffer, vb);
-	unsigned long flags;
 
 	dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d active=%p\n", __func__,
 		vb, vb->baddr, vb->bsize, pcdev->active);
 
-	spin_lock_irqsave(&pcdev->lock, flags);
-
 	list_add_tail(&vb->queue, &pcdev->capture);
 
 	vb->state = VIDEOBUF_ACTIVE;
@@ -633,8 +631,6 @@ static void pxa_videobuf_queue(struct videobuf_queue *vq,
 
 	if (!pcdev->active)
 		pxa_camera_start_capture(pcdev);
-
-	spin_unlock_irqrestore(&pcdev->lock, flags);
 }
 
 static void pxa_videobuf_release(struct videobuf_queue *vq,
diff --git a/drivers/media/video/sh_mobile_ceu_camera.c b/drivers/media/video/sh_mobile_ceu_camera.c
index 0db88a53d92..e86878deea7 100644
--- a/drivers/media/video/sh_mobile_ceu_camera.c
+++ b/drivers/media/video/sh_mobile_ceu_camera.c
@@ -282,27 +282,24 @@ out:
 	return ret;
 }
 
+/* Called under spinlock_irqsave(&pcdev->lock, ...) */
 static void sh_mobile_ceu_videobuf_queue(struct videobuf_queue *vq,
 					 struct videobuf_buffer *vb)
 {
 	struct soc_camera_device *icd = vq->priv_data;
 	struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent);
 	struct sh_mobile_ceu_dev *pcdev = ici->priv;
-	unsigned long flags;
 
 	dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %zd\n", __func__,
 		vb, vb->baddr, vb->bsize);
 
 	vb->state = VIDEOBUF_QUEUED;
-	spin_lock_irqsave(&pcdev->lock, flags);
 	list_add_tail(&vb->queue, &pcdev->capture);
 
 	if (!pcdev->active) {
 		pcdev->active = vb;
 		sh_mobile_ceu_capture(pcdev);
 	}
-
-	spin_unlock_irqrestore(&pcdev->lock, flags);
 }
 
 static void sh_mobile_ceu_videobuf_release(struct videobuf_queue *vq,
-- 
GitLab


From 99362e1ece9f9651af1b849a01d91b9df1e0db2c Mon Sep 17 00:00:00 2001
From: Hans Verkuil <hverkuil@xs4all.nl>
Date: Fri, 7 Aug 2009 07:10:52 -0300
Subject: [PATCH 0864/1153] V4L/DVB (12428): hdpvr: add missing initialization
 of current_norm

Drivers should either set current_norm or supply a g_std callback.

The hdpvr driver does neither. Since it initializes to a 60 Hz format
I've initialized the current_norm to NTSC | PAL_M | PAL_60 which is the
60 Hz subset of tvnorms.

Cc: Janne Grunau <j@jannau.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/hdpvr/hdpvr-video.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/media/video/hdpvr/hdpvr-video.c b/drivers/media/video/hdpvr/hdpvr-video.c
index ccd47f57f42..d678765cbba 100644
--- a/drivers/media/video/hdpvr/hdpvr-video.c
+++ b/drivers/media/video/hdpvr/hdpvr-video.c
@@ -1220,6 +1220,8 @@ static const struct video_device hdpvr_video_template = {
 		V4L2_STD_PAL_G | V4L2_STD_PAL_H | V4L2_STD_PAL_I |
 		V4L2_STD_PAL_D | V4L2_STD_PAL_M | V4L2_STD_PAL_N |
 		V4L2_STD_PAL_60,
+	.current_norm 		= V4L2_STD_NTSC | V4L2_STD_PAL_M |
+		V4L2_STD_PAL_60,
 };
 
 int hdpvr_register_videodev(struct hdpvr_device *dev, struct device *parent,
-- 
GitLab


From 9bedc7f7fe803c17d26b5fcf5786b50a7cf40def Mon Sep 17 00:00:00 2001
From: Hans Verkuil <hverkuil@xs4all.nl>
Date: Fri, 7 Aug 2009 07:28:16 -0300
Subject: [PATCH 0865/1153] V4L/DVB (12429): v4l2-ioctl: fix G_STD and G_PARM
 default handlers

The v4l core supplies default handlers for G_STD and G_PARM. However, both
default handlers are buggy.

This patch fixes the following:

1) If no g_std is supplied and current_norm == 0, then this driver does not
   support TV video standards (e.g. a radio or webcam driver). Return
   -EINVAL. This ensures that there is no bogus VIDIOC_G_STD support for
   such drivers.

2) The default VIDIOC_G_PARM handler used current_norm instead of first
   checking if the driver supported g_std and calling that to get the norm.
   It also didn't check if current_norm was 0, since in that case the driver
   does not support TV standards (or no standard was set at all) and the
   default handler should return -EINVAL.

Note that I am very unhappy with these default handlers: I think they
basically behave like some very strange and unexpected side-effect.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/v4l2-ioctl.c | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/drivers/media/video/v4l2-ioctl.c b/drivers/media/video/v4l2-ioctl.c
index be64a502ea2..f2afc4e0837 100644
--- a/drivers/media/video/v4l2-ioctl.c
+++ b/drivers/media/video/v4l2-ioctl.c
@@ -1081,8 +1081,10 @@ static long __video_do_ioctl(struct file *file,
 		/* Calls the specific handler */
 		if (ops->vidioc_g_std)
 			ret = ops->vidioc_g_std(file, fh, id);
-		else
+		else if (vfd->current_norm)
 			*id = vfd->current_norm;
+		else
+			ret = -EINVAL;
 
 		if (!ret)
 			dbgarg(cmd, "std=0x%08Lx\n", (long long unsigned)*id);
@@ -1553,12 +1555,19 @@ static long __video_do_ioctl(struct file *file,
 				break;
 			ret = ops->vidioc_g_parm(file, fh, p);
 		} else {
+			v4l2_std_id std = vfd->current_norm;
+
 			if (p->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
 				return -EINVAL;
 
-			v4l2_video_std_frame_period(vfd->current_norm,
-						    &p->parm.capture.timeperframe);
 			ret = 0;
+			if (ops->vidioc_g_std)
+				ret = ops->vidioc_g_std(file, fh, &std);
+			else if (std == 0)
+				ret = -EINVAL;
+			if (ret == 0)
+				v4l2_video_std_frame_period(std,
+						    &p->parm.capture.timeperframe);
 		}
 
 		dbgarg(cmd, "type=%d\n", p->type);
-- 
GitLab


From 01a5fd6ff3fbae9a599d3334a8cca0f00865e360 Mon Sep 17 00:00:00 2001
From: Devin Heitmueller <dheitmueller@kernellabs.com>
Date: Fri, 7 Aug 2009 09:25:06 -0300
Subject: [PATCH 0866/1153] V4L/DVB (12432): em28xx: fix regression in Empire
 DualTV digital tuning

Restore support for digital tuning caused by regression during introduction
of disable_i2c_gate parameter to zl10353 driver.

Thanks to user "Xwang" for reporting the problem and testing the fix

Cc: Xwang <xwang1976@email.it>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-dvb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/video/em28xx/em28xx-dvb.c b/drivers/media/video/em28xx/em28xx-dvb.c
index cf0ac7f2a30..d603575431b 100644
--- a/drivers/media/video/em28xx/em28xx-dvb.c
+++ b/drivers/media/video/em28xx/em28xx-dvb.c
@@ -478,7 +478,6 @@ static int dvb_init(struct em28xx *dev)
 		}
 		break;
 	case EM2880_BOARD_KWORLD_DVB_310U:
-	case EM2880_BOARD_EMPIRE_DUAL_TV:
 		dvb->frontend = dvb_attach(zl10353_attach,
 					   &em28xx_zl10353_with_xc3028,
 					   &dev->i2c_adap);
@@ -488,6 +487,7 @@ static int dvb_init(struct em28xx *dev)
 		}
 		break;
 	case EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900:
+	case EM2880_BOARD_EMPIRE_DUAL_TV:
 		dvb->frontend = dvb_attach(zl10353_attach,
 					   &em28xx_zl10353_xc3028_no_i2c_gate,
 					   &dev->i2c_adap);
-- 
GitLab


From 77f2c2db1146154fb054e9ce955928a66d8c959f Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Mon, 10 Aug 2009 22:17:25 -0300
Subject: [PATCH 0867/1153] V4L/DVB (12436): stk-webcam: read buffer overflow

It tested the value of stk_sizes[i].m before checking whether i was in range.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/stk-webcam.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/media/video/stk-webcam.c b/drivers/media/video/stk-webcam.c
index 4d6785e6345..b154bd961e3 100644
--- a/drivers/media/video/stk-webcam.c
+++ b/drivers/media/video/stk-webcam.c
@@ -1050,8 +1050,8 @@ static int stk_setup_format(struct stk_camera *dev)
 		depth = 1;
 	else
 		depth = 2;
-	while (stk_sizes[i].m != dev->vsettings.mode
-			&& i < ARRAY_SIZE(stk_sizes))
+	while (i < ARRAY_SIZE(stk_sizes) &&
+			stk_sizes[i].m != dev->vsettings.mode)
 		i++;
 	if (i == ARRAY_SIZE(stk_sizes)) {
 		STK_ERROR("Something is broken in %s\n", __func__);
-- 
GitLab


From 27059b35397fc7cf2cbf5b4b99d912bbc06aff4d Mon Sep 17 00:00:00 2001
From: Randy Dunlap <randy.dunlap@oracle.com>
Date: Mon, 10 Aug 2009 21:59:16 -0300
Subject: [PATCH 0868/1153] V4L/DVB (12437): dvb: siano uses/depends on INPUT

siano uses input_*() functions so it should depend on INPUT
to prevent build errors:

ERROR: "input_event" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_register_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_free_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_unregister_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_allocate_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!

Cc: Michael Krufky <mkrufky@linuxtv.org>
Cc: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/dvb/siano/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/dvb/siano/Kconfig b/drivers/media/dvb/siano/Kconfig
index dd863f26167..88847d1dcbb 100644
--- a/drivers/media/dvb/siano/Kconfig
+++ b/drivers/media/dvb/siano/Kconfig
@@ -4,7 +4,7 @@
 
 config DVB_SIANO_SMS1XXX
 	tristate "Siano SMS1XXX USB dongle support"
-	depends on DVB_CORE && USB
+	depends on DVB_CORE && USB && INPUT
 	---help---
 	  Choose Y here if you have a USB dongle with a SMS1XXX chipset.
 
-- 
GitLab


From bb2b4542b6415044894cd7c147ff54840dd8ed3f Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Mon, 10 Aug 2009 22:07:54 -0300
Subject: [PATCH 0869/1153] V4L/DVB (12438): Read buffer overflow

parport[n] is checked before n < MAX_CAMS

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/bw-qcam.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/video/bw-qcam.c b/drivers/media/video/bw-qcam.c
index 10dbd4a11b3..9e39bc5f7b0 100644
--- a/drivers/media/video/bw-qcam.c
+++ b/drivers/media/video/bw-qcam.c
@@ -992,7 +992,7 @@ static int accept_bwqcam(struct parport *port)
 
 	if (parport[0] && strncmp(parport[0], "auto", 4) != 0) {
 		/* user gave parport parameters */
-		for(n=0; parport[n] && n<MAX_CAMS; n++){
+		for (n = 0; n < MAX_CAMS && parport[n]; n++) {
 			char *ep;
 			unsigned long r;
 			r = simple_strtoul(parport[n], &ep, 0);
-- 
GitLab


From 084e24acc906c162c92de7df807190856ae60928 Mon Sep 17 00:00:00 2001
From: Matthias Schwarzott <zzam@gentoo.org>
Date: Mon, 10 Aug 2009 22:51:01 -0300
Subject: [PATCH 0870/1153] V4L/DVB (12440): Use kzalloc for frontend states to
 have struct dvb_frontend properly

This patch changes most frontend drivers to allocate their state structure via
kzalloc and not kmalloc. This is done to properly initialize the
embedded "struct dvb_frontend frontend" field, that they all have.

The visible effect of this struct being uninitalized is, that the member "id"
that is used to set the name of kernel thread is totally random.

Some board drivers (for example cx88-dvb) set this "id" via
videobuf_dvb_alloc_frontend but most do not.

So I at least get random id values for saa7134, flexcop and ttpci based cards.
It looks like this in dmesg:
DVB: registering adapter 1 frontend -10551321 (ST STV0299 DVB-S)

The related kernel thread then also gets a strange name
like "kdvb-ad-1-fe--1".

Cc: Michael Krufky <mkrufky@linuxtv.org>
Cc: Steven Toth <stoth@linuxtv.org>
Cc: Timothy Lee <timothy.lee@siriushk.com>
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/dvb/frontends/cx22700.c      | 2 +-
 drivers/media/dvb/frontends/cx22702.c      | 2 +-
 drivers/media/dvb/frontends/cx24110.c      | 2 +-
 drivers/media/dvb/frontends/dvb_dummy_fe.c | 6 +++---
 drivers/media/dvb/frontends/l64781.c       | 2 +-
 drivers/media/dvb/frontends/lgs8gl5.c      | 2 +-
 drivers/media/dvb/frontends/mt312.c        | 2 +-
 drivers/media/dvb/frontends/nxt6000.c      | 2 +-
 drivers/media/dvb/frontends/or51132.c      | 2 +-
 drivers/media/dvb/frontends/or51211.c      | 2 +-
 drivers/media/dvb/frontends/s5h1409.c      | 2 +-
 drivers/media/dvb/frontends/s5h1411.c      | 2 +-
 drivers/media/dvb/frontends/si21xx.c       | 2 +-
 drivers/media/dvb/frontends/sp8870.c       | 2 +-
 drivers/media/dvb/frontends/sp887x.c       | 2 +-
 drivers/media/dvb/frontends/stv0288.c      | 2 +-
 drivers/media/dvb/frontends/stv0297.c      | 2 +-
 drivers/media/dvb/frontends/stv0299.c      | 2 +-
 drivers/media/dvb/frontends/tda10021.c     | 2 +-
 drivers/media/dvb/frontends/tda10048.c     | 2 +-
 drivers/media/dvb/frontends/tda1004x.c     | 4 ++--
 drivers/media/dvb/frontends/tda10086.c     | 2 +-
 drivers/media/dvb/frontends/tda8083.c      | 2 +-
 drivers/media/dvb/frontends/ves1820.c      | 2 +-
 drivers/media/dvb/frontends/ves1x93.c      | 2 +-
 25 files changed, 28 insertions(+), 28 deletions(-)

diff --git a/drivers/media/dvb/frontends/cx22700.c b/drivers/media/dvb/frontends/cx22700.c
index ace5cb17165..fbd838eca26 100644
--- a/drivers/media/dvb/frontends/cx22700.c
+++ b/drivers/media/dvb/frontends/cx22700.c
@@ -380,7 +380,7 @@ struct dvb_frontend* cx22700_attach(const struct cx22700_config* config,
 	struct cx22700_state* state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct cx22700_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct cx22700_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* setup the state */
diff --git a/drivers/media/dvb/frontends/cx22702.c b/drivers/media/dvb/frontends/cx22702.c
index 5d1abe34bdd..00b5c7e91d5 100644
--- a/drivers/media/dvb/frontends/cx22702.c
+++ b/drivers/media/dvb/frontends/cx22702.c
@@ -580,7 +580,7 @@ struct dvb_frontend *cx22702_attach(const struct cx22702_config *config,
 	struct cx22702_state *state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct cx22702_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct cx22702_state), GFP_KERNEL);
 	if (state == NULL)
 		goto error;
 
diff --git a/drivers/media/dvb/frontends/cx24110.c b/drivers/media/dvb/frontends/cx24110.c
index 87ae29db024..ffbcfabd83f 100644
--- a/drivers/media/dvb/frontends/cx24110.c
+++ b/drivers/media/dvb/frontends/cx24110.c
@@ -598,7 +598,7 @@ struct dvb_frontend* cx24110_attach(const struct cx24110_config* config,
 	int ret;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct cx24110_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct cx24110_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* setup the state */
diff --git a/drivers/media/dvb/frontends/dvb_dummy_fe.c b/drivers/media/dvb/frontends/dvb_dummy_fe.c
index db8a937cc63..a7fc7e53a55 100644
--- a/drivers/media/dvb/frontends/dvb_dummy_fe.c
+++ b/drivers/media/dvb/frontends/dvb_dummy_fe.c
@@ -117,7 +117,7 @@ struct dvb_frontend* dvb_dummy_fe_ofdm_attach(void)
 	struct dvb_dummy_fe_state* state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* create dvb_frontend */
@@ -137,7 +137,7 @@ struct dvb_frontend *dvb_dummy_fe_qpsk_attach(void)
 	struct dvb_dummy_fe_state* state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* create dvb_frontend */
@@ -157,7 +157,7 @@ struct dvb_frontend *dvb_dummy_fe_qam_attach(void)
 	struct dvb_dummy_fe_state* state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct dvb_dummy_fe_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* create dvb_frontend */
diff --git a/drivers/media/dvb/frontends/l64781.c b/drivers/media/dvb/frontends/l64781.c
index e1e70e9e0cb..3051b64aa17 100644
--- a/drivers/media/dvb/frontends/l64781.c
+++ b/drivers/media/dvb/frontends/l64781.c
@@ -501,7 +501,7 @@ struct dvb_frontend* l64781_attach(const struct l64781_config* config,
 			   { .addr = config->demod_address, .flags = I2C_M_RD, .buf = b1, .len = 1 } };
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct l64781_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct l64781_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* setup the state */
diff --git a/drivers/media/dvb/frontends/lgs8gl5.c b/drivers/media/dvb/frontends/lgs8gl5.c
index 855852fddf2..bb37ed289a0 100644
--- a/drivers/media/dvb/frontends/lgs8gl5.c
+++ b/drivers/media/dvb/frontends/lgs8gl5.c
@@ -387,7 +387,7 @@ lgs8gl5_attach(const struct lgs8gl5_config *config, struct i2c_adapter *i2c)
 	dprintk("%s\n", __func__);
 
 	/* Allocate memory for the internal state */
-	state = kmalloc(sizeof(struct lgs8gl5_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct lgs8gl5_state), GFP_KERNEL);
 	if (state == NULL)
 		goto error;
 
diff --git a/drivers/media/dvb/frontends/mt312.c b/drivers/media/dvb/frontends/mt312.c
index a621f727935..f69daaac78c 100644
--- a/drivers/media/dvb/frontends/mt312.c
+++ b/drivers/media/dvb/frontends/mt312.c
@@ -782,7 +782,7 @@ struct dvb_frontend *mt312_attach(const struct mt312_config *config,
 	struct mt312_state *state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct mt312_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct mt312_state), GFP_KERNEL);
 	if (state == NULL)
 		goto error;
 
diff --git a/drivers/media/dvb/frontends/nxt6000.c b/drivers/media/dvb/frontends/nxt6000.c
index 0eef22dbf8a..a763ec756f7 100644
--- a/drivers/media/dvb/frontends/nxt6000.c
+++ b/drivers/media/dvb/frontends/nxt6000.c
@@ -545,7 +545,7 @@ struct dvb_frontend* nxt6000_attach(const struct nxt6000_config* config,
 	struct nxt6000_state* state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct nxt6000_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct nxt6000_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* setup the state */
diff --git a/drivers/media/dvb/frontends/or51132.c b/drivers/media/dvb/frontends/or51132.c
index 8133ea3cddd..38e67accb8c 100644
--- a/drivers/media/dvb/frontends/or51132.c
+++ b/drivers/media/dvb/frontends/or51132.c
@@ -562,7 +562,7 @@ struct dvb_frontend* or51132_attach(const struct or51132_config* config,
 	struct or51132_state* state = NULL;
 
 	/* Allocate memory for the internal state */
-	state = kmalloc(sizeof(struct or51132_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct or51132_state), GFP_KERNEL);
 	if (state == NULL)
 		return NULL;
 
diff --git a/drivers/media/dvb/frontends/or51211.c b/drivers/media/dvb/frontends/or51211.c
index 16cf2fdd5d7..c709ce6771c 100644
--- a/drivers/media/dvb/frontends/or51211.c
+++ b/drivers/media/dvb/frontends/or51211.c
@@ -527,7 +527,7 @@ struct dvb_frontend* or51211_attach(const struct or51211_config* config,
 	struct or51211_state* state = NULL;
 
 	/* Allocate memory for the internal state */
-	state = kmalloc(sizeof(struct or51211_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct or51211_state), GFP_KERNEL);
 	if (state == NULL)
 		return NULL;
 
diff --git a/drivers/media/dvb/frontends/s5h1409.c b/drivers/media/dvb/frontends/s5h1409.c
index 3e08d985d6e..fb301151842 100644
--- a/drivers/media/dvb/frontends/s5h1409.c
+++ b/drivers/media/dvb/frontends/s5h1409.c
@@ -796,7 +796,7 @@ struct dvb_frontend *s5h1409_attach(const struct s5h1409_config *config,
 	u16 reg;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct s5h1409_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct s5h1409_state), GFP_KERNEL);
 	if (state == NULL)
 		goto error;
 
diff --git a/drivers/media/dvb/frontends/s5h1411.c b/drivers/media/dvb/frontends/s5h1411.c
index 66e2dd6d6fe..d8adf1e3201 100644
--- a/drivers/media/dvb/frontends/s5h1411.c
+++ b/drivers/media/dvb/frontends/s5h1411.c
@@ -844,7 +844,7 @@ struct dvb_frontend *s5h1411_attach(const struct s5h1411_config *config,
 	u16 reg;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct s5h1411_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct s5h1411_state), GFP_KERNEL);
 	if (state == NULL)
 		goto error;
 
diff --git a/drivers/media/dvb/frontends/si21xx.c b/drivers/media/dvb/frontends/si21xx.c
index 0bd16af8a6c..9552a22ccff 100644
--- a/drivers/media/dvb/frontends/si21xx.c
+++ b/drivers/media/dvb/frontends/si21xx.c
@@ -928,7 +928,7 @@ struct dvb_frontend *si21xx_attach(const struct si21xx_config *config,
 	dprintk("%s\n", __func__);
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct si21xx_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct si21xx_state), GFP_KERNEL);
 	if (state == NULL)
 		goto error;
 
diff --git a/drivers/media/dvb/frontends/sp8870.c b/drivers/media/dvb/frontends/sp8870.c
index 1c9a9b4051b..b85eb60a893 100644
--- a/drivers/media/dvb/frontends/sp8870.c
+++ b/drivers/media/dvb/frontends/sp8870.c
@@ -557,7 +557,7 @@ struct dvb_frontend* sp8870_attach(const struct sp8870_config* config,
 	struct sp8870_state* state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct sp8870_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct sp8870_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* setup the state */
diff --git a/drivers/media/dvb/frontends/sp887x.c b/drivers/media/dvb/frontends/sp887x.c
index 559509ab4da..4a7c3d84260 100644
--- a/drivers/media/dvb/frontends/sp887x.c
+++ b/drivers/media/dvb/frontends/sp887x.c
@@ -557,7 +557,7 @@ struct dvb_frontend* sp887x_attach(const struct sp887x_config* config,
 	struct sp887x_state* state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct sp887x_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct sp887x_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* setup the state */
diff --git a/drivers/media/dvb/frontends/stv0288.c b/drivers/media/dvb/frontends/stv0288.c
index ff1194de34c..2930a5d6768 100644
--- a/drivers/media/dvb/frontends/stv0288.c
+++ b/drivers/media/dvb/frontends/stv0288.c
@@ -570,7 +570,7 @@ struct dvb_frontend *stv0288_attach(const struct stv0288_config *config,
 	int id;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct stv0288_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct stv0288_state), GFP_KERNEL);
 	if (state == NULL)
 		goto error;
 
diff --git a/drivers/media/dvb/frontends/stv0297.c b/drivers/media/dvb/frontends/stv0297.c
index 62caf802ed9..4fd7479bb62 100644
--- a/drivers/media/dvb/frontends/stv0297.c
+++ b/drivers/media/dvb/frontends/stv0297.c
@@ -663,7 +663,7 @@ struct dvb_frontend *stv0297_attach(const struct stv0297_config *config,
 	struct stv0297_state *state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct stv0297_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct stv0297_state), GFP_KERNEL);
 	if (state == NULL)
 		goto error;
 
diff --git a/drivers/media/dvb/frontends/stv0299.c b/drivers/media/dvb/frontends/stv0299.c
index 6c1cb1973c6..96887446972 100644
--- a/drivers/media/dvb/frontends/stv0299.c
+++ b/drivers/media/dvb/frontends/stv0299.c
@@ -667,7 +667,7 @@ struct dvb_frontend* stv0299_attach(const struct stv0299_config* config,
 	int id;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct stv0299_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct stv0299_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* setup the state */
diff --git a/drivers/media/dvb/frontends/tda10021.c b/drivers/media/dvb/frontends/tda10021.c
index f648fdb64bb..f5d7b3277a2 100644
--- a/drivers/media/dvb/frontends/tda10021.c
+++ b/drivers/media/dvb/frontends/tda10021.c
@@ -413,7 +413,7 @@ struct dvb_frontend* tda10021_attach(const struct tda1002x_config* config,
 	u8 id;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct tda10021_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct tda10021_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* setup the state */
diff --git a/drivers/media/dvb/frontends/tda10048.c b/drivers/media/dvb/frontends/tda10048.c
index cc8862ce4aa..4e2a7c8b2f6 100644
--- a/drivers/media/dvb/frontends/tda10048.c
+++ b/drivers/media/dvb/frontends/tda10048.c
@@ -1095,7 +1095,7 @@ struct dvb_frontend *tda10048_attach(const struct tda10048_config *config,
 	dprintk(1, "%s()\n", __func__);
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct tda10048_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct tda10048_state), GFP_KERNEL);
 	if (state == NULL)
 		goto error;
 
diff --git a/drivers/media/dvb/frontends/tda1004x.c b/drivers/media/dvb/frontends/tda1004x.c
index 4981cef8b44..f2a8abe0a24 100644
--- a/drivers/media/dvb/frontends/tda1004x.c
+++ b/drivers/media/dvb/frontends/tda1004x.c
@@ -1269,7 +1269,7 @@ struct dvb_frontend* tda10045_attach(const struct tda1004x_config* config,
 	int id;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct tda1004x_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct tda1004x_state), GFP_KERNEL);
 	if (!state) {
 		printk(KERN_ERR "Can't alocate memory for tda10045 state\n");
 		return NULL;
@@ -1339,7 +1339,7 @@ struct dvb_frontend* tda10046_attach(const struct tda1004x_config* config,
 	int id;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct tda1004x_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct tda1004x_state), GFP_KERNEL);
 	if (!state) {
 		printk(KERN_ERR "Can't alocate memory for tda10046 state\n");
 		return NULL;
diff --git a/drivers/media/dvb/frontends/tda10086.c b/drivers/media/dvb/frontends/tda10086.c
index a17ce3c4ad8..f2c8faac6f3 100644
--- a/drivers/media/dvb/frontends/tda10086.c
+++ b/drivers/media/dvb/frontends/tda10086.c
@@ -745,7 +745,7 @@ struct dvb_frontend* tda10086_attach(const struct tda10086_config* config,
 	dprintk ("%s\n", __func__);
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct tda10086_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct tda10086_state), GFP_KERNEL);
 	if (!state)
 		return NULL;
 
diff --git a/drivers/media/dvb/frontends/tda8083.c b/drivers/media/dvb/frontends/tda8083.c
index 5b843b2e67e..9369f7442f2 100644
--- a/drivers/media/dvb/frontends/tda8083.c
+++ b/drivers/media/dvb/frontends/tda8083.c
@@ -417,7 +417,7 @@ struct dvb_frontend* tda8083_attach(const struct tda8083_config* config,
 	struct tda8083_state* state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct tda8083_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct tda8083_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* setup the state */
diff --git a/drivers/media/dvb/frontends/ves1820.c b/drivers/media/dvb/frontends/ves1820.c
index a184597f1d9..6e78e486551 100644
--- a/drivers/media/dvb/frontends/ves1820.c
+++ b/drivers/media/dvb/frontends/ves1820.c
@@ -374,7 +374,7 @@ struct dvb_frontend* ves1820_attach(const struct ves1820_config* config,
 	struct ves1820_state* state = NULL;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct ves1820_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct ves1820_state), GFP_KERNEL);
 	if (state == NULL)
 		goto error;
 
diff --git a/drivers/media/dvb/frontends/ves1x93.c b/drivers/media/dvb/frontends/ves1x93.c
index bd558960bd8..8d7854c2fb0 100644
--- a/drivers/media/dvb/frontends/ves1x93.c
+++ b/drivers/media/dvb/frontends/ves1x93.c
@@ -456,7 +456,7 @@ struct dvb_frontend* ves1x93_attach(const struct ves1x93_config* config,
 	u8 identity;
 
 	/* allocate memory for the internal state */
-	state = kmalloc(sizeof(struct ves1x93_state), GFP_KERNEL);
+	state = kzalloc(sizeof(struct ves1x93_state), GFP_KERNEL);
 	if (state == NULL) goto error;
 
 	/* setup the state */
-- 
GitLab


From 08b39642b1e375afd014c50f6013ec4a292ca3b2 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Mon, 10 Aug 2009 22:59:33 -0300
Subject: [PATCH 0871/1153] V4L/DVB (12441): siano: read buffer overflow

With mode DEVICE_MODE_RAW_TUNER a read occurs past the end of smscore_fw_lkup[].
Subsequently an attempt is made to load the firmware from the resulting
filename.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/dvb/siano/smscoreapi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/dvb/siano/smscoreapi.c b/drivers/media/dvb/siano/smscoreapi.c
index a246903c334..bd9ab9d0d12 100644
--- a/drivers/media/dvb/siano/smscoreapi.c
+++ b/drivers/media/dvb/siano/smscoreapi.c
@@ -816,7 +816,7 @@ int smscore_set_device_mode(struct smscore_device_t *coredev, int mode)
 
 	sms_debug("set device mode to %d", mode);
 	if (coredev->device_flags & SMS_DEVICE_FAMILY2) {
-		if (mode < DEVICE_MODE_DVBT || mode > DEVICE_MODE_RAW_TUNER) {
+		if (mode < DEVICE_MODE_DVBT || mode >= DEVICE_MODE_RAW_TUNER) {
 			sms_err("invalid mode specified %d", mode);
 			return -EINVAL;
 		}
-- 
GitLab


From a219dc4d4463809b1be473038e7d9f3437ca452d Mon Sep 17 00:00:00 2001
From: Ramax Lo <ramaxlo@gmail.com>
Date: Wed, 12 Aug 2009 23:55:56 +0800
Subject: [PATCH 0872/1153] ARM: S3C64XX: serial: Fix a typo in Kconfig

The typo causes drivers/serial/s3c6400.c not being built for s3c6400 platform.

Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/serial/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 037c1e0b7c4..6553833c12d 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -527,7 +527,7 @@ config SERIAL_S3C24A0
 
 config SERIAL_S3C6400
 	tristate "Samsung S3C6400/S3C6410 Serial port support"
-	depends on SERIAL_SAMSUNG && (CPU_S3C600 || CPU_S3C6410)
+	depends on SERIAL_SAMSUNG && (CPU_S3C6400 || CPU_S3C6410)
 	default y
 	help
 	  Serial port support for the Samsung S3C6400 and S3C6410
-- 
GitLab


From 48ec45e725aa385d72bced73b267dfaf13351876 Mon Sep 17 00:00:00 2001
From: Davide Rizzo <elpa.rizzo@gmail.com>
Date: Thu, 13 Aug 2009 11:53:53 +0200
Subject: [PATCH 0873/1153] ARM: S3C24XX: Fix clkout mpx error

Bug correction: CLK Outputs cannot have XTAL as parent

Signed-off-by: Davide Rizzo <elpa.rizzo@gmail.com>
[ben-linux@fluff.org: updated patch subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 arch/arm/plat-s3c24xx/clock-dclk.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/plat-s3c24xx/clock-dclk.c b/arch/arm/plat-s3c24xx/clock-dclk.c
index 5b75a797b5a..0afb217a775 100644
--- a/arch/arm/plat-s3c24xx/clock-dclk.c
+++ b/arch/arm/plat-s3c24xx/clock-dclk.c
@@ -129,7 +129,7 @@ static int s3c24xx_clkout_setparent(struct clk *clk, struct clk *parent)
 
 	/* calculate the MISCCR setting for the clock */
 
-	if (parent == &clk_xtal)
+	if (parent == &clk_mpll)
 		source = S3C2410_MISCCR_CLK0_MPLL;
 	else if (parent == &clk_upll)
 		source = S3C2410_MISCCR_CLK0_UPLL;
-- 
GitLab


From 17e78b0655da20f2fc2bbde3b8252dac07c82914 Mon Sep 17 00:00:00 2001
From: Yi Zou <yi.zou@intel.com>
Date: Thu, 13 Aug 2009 14:09:58 +0000
Subject: [PATCH 0874/1153] ixgbe: Do not return 0 in ixgbe_fcoe_ddp() upon
 FCP_RSP in DDP completion

We return the ddp->len in ixgbe_fcoe_ddp() to indicate the length of data that
have been DDPed. However, it is possible that the length is 0, e.g., for SCSI
READ, the FCP_RSP may come back w/ SCSI status 0x28 as Task Set Full with no FCP
data for DDP. In ixgbe_fcoe_ddp(), we return 0 to indicate not passing DDPed
packets to upper layer. Therefore in the case of ddp->len being 0 upon FCP_RSP,
we do not want to return the 0 ddp->len as we want FCP_RSP to be always
delivered to the upper layer. This patch fixes this bug by setting rc only if
ddp->len is non-zero.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ixgbe/ixgbe_fcoe.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ixgbe/ixgbe_fcoe.c b/drivers/net/ixgbe/ixgbe_fcoe.c
index fa9f24e2368..28cf104e36c 100644
--- a/drivers/net/ixgbe/ixgbe_fcoe.c
+++ b/drivers/net/ixgbe/ixgbe_fcoe.c
@@ -336,7 +336,7 @@ int ixgbe_fcoe_ddp(struct ixgbe_adapter *adapter,
 		/* return 0 to bypass going to ULD for DDPed data */
 		if (fcstat == IXGBE_RXDADV_STAT_FCSTAT_DDP)
 			rc = 0;
-		else
+		else if (ddp->len)
 			rc = ddp->len;
 	}
 
-- 
GitLab


From 8a62babfb87aa5911e87e0ce38381bdfdc4a2b83 Mon Sep 17 00:00:00 2001
From: Lucy Liu <lucy.liu@intel.com>
Date: Thu, 13 Aug 2009 14:09:38 +0000
Subject: [PATCH 0875/1153] ixgbe: Fix receive on real device when VLANs are
 configured

Traffic received with a priority tag (VID = 0) and non-zero priority value was
incorrectly handled by the VLAN packet code path due to a check on zero for
the whole VLAN tag instead of just the VID.

This patch masked out the priority field when checking the vlan tag for
received VLAN packets.

Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ixgbe/ixgbe_main.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c
index e3cb949b9aa..77b0381a2b5 100644
--- a/drivers/net/ixgbe/ixgbe_main.c
+++ b/drivers/net/ixgbe/ixgbe_main.c
@@ -492,12 +492,12 @@ static void ixgbe_receive_skb(struct ixgbe_q_vector *q_vector,
 
 	skb_record_rx_queue(skb, ring->queue_index);
 	if (!(adapter->flags & IXGBE_FLAG_IN_NETPOLL)) {
-		if (adapter->vlgrp && is_vlan && (tag != 0))
+		if (adapter->vlgrp && is_vlan && (tag & VLAN_VID_MASK))
 			vlan_gro_receive(napi, adapter->vlgrp, tag, skb);
 		else
 			napi_gro_receive(napi, skb);
 	} else {
-		if (adapter->vlgrp && is_vlan && (tag != 0))
+		if (adapter->vlgrp && is_vlan && (tag & VLAN_VID_MASK))
 			vlan_hwaccel_rx(skb, adapter->vlgrp, tag);
 		else
 			netif_rx(skb);
-- 
GitLab


From d6647bdf98a0de19963de8d5d9698d469ed72097 Mon Sep 17 00:00:00 2001
From: Tejun Heo <tj@kernel.org>
Date: Tue, 21 Jul 2009 17:11:50 +0900
Subject: [PATCH 0876/1153] init: set nr_cpu_ids before setup_per_cpu_areas()

nr_cpu_ids is dependent only on cpu_possible_map and
setup_per_cpu_areas() already depends on cpu_possible_map and will use
nr_cpu_ids.  Initialize nr_cpu_ids before setting up percpu areas.

Signed-off-by: Tejun Heo <tj@kernel.org>
---
 init/main.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/init/main.c b/init/main.c
index 2c5ade79eb8..2d9d6bdfe7c 100644
--- a/init/main.c
+++ b/init/main.c
@@ -584,8 +584,8 @@ asmlinkage void __init start_kernel(void)
 	setup_arch(&command_line);
 	mm_init_owner(&init_mm, &init_task);
 	setup_command_line(command_line);
-	setup_per_cpu_areas();
 	setup_nr_cpu_ids();
+	setup_per_cpu_areas();
 	smp_prepare_boot_cpu();	/* arch-specific boot-cpu hooks */
 
 	build_all_zonelists();
-- 
GitLab


From 74d46d6b2d23d44d72c37df4c6a5d2e782f7b088 Mon Sep 17 00:00:00 2001
From: Tejun Heo <tj@kernel.org>
Date: Tue, 21 Jul 2009 17:11:50 +0900
Subject: [PATCH 0877/1153] percpu, sparc64: fix sparse possible cpu map
 handling

percpu code has been assuming num_possible_cpus() == nr_cpu_ids which
is incorrect if cpu_possible_map contains holes.  This causes percpu
code to access beyond allocated memories and vmalloc areas.  On a
sparc64 machine with cpus 0 and 2 (u60), this triggers the following
warning or fails boot.

 WARNING: at /devel/tj/os/work/mm/vmalloc.c:106 vmap_page_range_noflush+0x1f0/0x240()
 Modules linked in:
 Call Trace:
  [00000000004b17d0] vmap_page_range_noflush+0x1f0/0x240
  [00000000004b1840] map_vm_area+0x20/0x60
  [00000000004b1950] __vmalloc_area_node+0xd0/0x160
  [0000000000593434] deflate_init+0x14/0xe0
  [0000000000583b94] __crypto_alloc_tfm+0xd4/0x1e0
  [00000000005844f0] crypto_alloc_base+0x50/0xa0
  [000000000058b898] alg_test_comp+0x18/0x80
  [000000000058dad4] alg_test+0x54/0x180
  [000000000058af00] cryptomgr_test+0x40/0x60
  [0000000000473098] kthread+0x58/0x80
  [000000000042b590] kernel_thread+0x30/0x60
  [0000000000472fd0] kthreadd+0xf0/0x160
 ---[ end trace 429b268a213317ba ]---

This patch fixes generic percpu functions and sparc64
setup_per_cpu_areas() so that they handle sparse cpu_possible_map
properly.

Please note that on x86, cpu_possible_map() doesn't contain holes and
thus num_possible_cpus() == nr_cpu_ids and this patch doesn't cause
any behavior difference.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
---
 arch/sparc/kernel/smp_64.c     |  4 ++--
 arch/x86/kernel/setup_percpu.c | 14 +++++++-------
 mm/percpu.c                    | 33 ++++++++++++++++++---------------
 3 files changed, 27 insertions(+), 24 deletions(-)

diff --git a/arch/sparc/kernel/smp_64.c b/arch/sparc/kernel/smp_64.c
index fa44eaf8d89..3691907a43b 100644
--- a/arch/sparc/kernel/smp_64.c
+++ b/arch/sparc/kernel/smp_64.c
@@ -1499,7 +1499,7 @@ void __init setup_per_cpu_areas(void)
 	dyn_size = pcpur_size - static_size - PERCPU_MODULE_RESERVE;
 
 
-	ptrs_size = PFN_ALIGN(num_possible_cpus() * sizeof(pcpur_ptrs[0]));
+	ptrs_size = PFN_ALIGN(nr_cpu_ids * sizeof(pcpur_ptrs[0]));
 	pcpur_ptrs = alloc_bootmem(ptrs_size);
 
 	for_each_possible_cpu(cpu) {
@@ -1514,7 +1514,7 @@ void __init setup_per_cpu_areas(void)
 
 	/* allocate address and map */
 	vm.flags = VM_ALLOC;
-	vm.size = num_possible_cpus() * PCPU_CHUNK_SIZE;
+	vm.size = nr_cpu_ids * PCPU_CHUNK_SIZE;
 	vm_area_register_early(&vm, PCPU_CHUNK_SIZE);
 
 	for_each_possible_cpu(cpu) {
diff --git a/arch/x86/kernel/setup_percpu.c b/arch/x86/kernel/setup_percpu.c
index 29a3eef7cf4..07d81916f21 100644
--- a/arch/x86/kernel/setup_percpu.c
+++ b/arch/x86/kernel/setup_percpu.c
@@ -165,7 +165,7 @@ static ssize_t __init setup_pcpu_lpage(size_t static_size, bool chosen)
 
 	if (!chosen) {
 		size_t vm_size = VMALLOC_END - VMALLOC_START;
-		size_t tot_size = num_possible_cpus() * PMD_SIZE;
+		size_t tot_size = nr_cpu_ids * PMD_SIZE;
 
 		/* on non-NUMA, embedding is better */
 		if (!pcpu_need_numa())
@@ -199,7 +199,7 @@ static ssize_t __init setup_pcpu_lpage(size_t static_size, bool chosen)
 	dyn_size = pcpul_size - static_size - PERCPU_FIRST_CHUNK_RESERVE;
 
 	/* allocate pointer array and alloc large pages */
-	map_size = PFN_ALIGN(num_possible_cpus() * sizeof(pcpul_map[0]));
+	map_size = PFN_ALIGN(nr_cpu_ids * sizeof(pcpul_map[0]));
 	pcpul_map = alloc_bootmem(map_size);
 
 	for_each_possible_cpu(cpu) {
@@ -228,7 +228,7 @@ static ssize_t __init setup_pcpu_lpage(size_t static_size, bool chosen)
 
 	/* allocate address and map */
 	pcpul_vm.flags = VM_ALLOC;
-	pcpul_vm.size = num_possible_cpus() * PMD_SIZE;
+	pcpul_vm.size = nr_cpu_ids * PMD_SIZE;
 	vm_area_register_early(&pcpul_vm, PMD_SIZE);
 
 	for_each_possible_cpu(cpu) {
@@ -250,8 +250,8 @@ static ssize_t __init setup_pcpu_lpage(size_t static_size, bool chosen)
 				     PMD_SIZE, pcpul_vm.addr, NULL);
 
 	/* sort pcpul_map array for pcpu_lpage_remapped() */
-	for (i = 0; i < num_possible_cpus() - 1; i++)
-		for (j = i + 1; j < num_possible_cpus(); j++)
+	for (i = 0; i < nr_cpu_ids - 1; i++)
+		for (j = i + 1; j < nr_cpu_ids; j++)
 			if (pcpul_map[i].ptr > pcpul_map[j].ptr) {
 				struct pcpul_ent tmp = pcpul_map[i];
 				pcpul_map[i] = pcpul_map[j];
@@ -288,7 +288,7 @@ void *pcpu_lpage_remapped(void *kaddr)
 {
 	void *pmd_addr = (void *)((unsigned long)kaddr & PMD_MASK);
 	unsigned long offset = (unsigned long)kaddr & ~PMD_MASK;
-	int left = 0, right = num_possible_cpus() - 1;
+	int left = 0, right = nr_cpu_ids - 1;
 	int pos;
 
 	/* pcpul in use at all? */
@@ -377,7 +377,7 @@ static ssize_t __init setup_pcpu_4k(size_t static_size)
 	pcpu4k_nr_static_pages = PFN_UP(static_size);
 
 	/* unaligned allocations can't be freed, round up to page size */
-	pages_size = PFN_ALIGN(pcpu4k_nr_static_pages * num_possible_cpus()
+	pages_size = PFN_ALIGN(pcpu4k_nr_static_pages * nr_cpu_ids
 			       * sizeof(pcpu4k_pages[0]));
 	pcpu4k_pages = alloc_bootmem(pages_size);
 
diff --git a/mm/percpu.c b/mm/percpu.c
index b70f2acd885..e0be1146f61 100644
--- a/mm/percpu.c
+++ b/mm/percpu.c
@@ -8,12 +8,12 @@
  *
  * This is percpu allocator which can handle both static and dynamic
  * areas.  Percpu areas are allocated in chunks in vmalloc area.  Each
- * chunk is consisted of num_possible_cpus() units and the first chunk
- * is used for static percpu variables in the kernel image (special
- * boot time alloc/init handling necessary as these areas need to be
- * brought up before allocation services are running).  Unit grows as
- * necessary and all units grow or shrink in unison.  When a chunk is
- * filled up, another chunk is allocated.  ie. in vmalloc area
+ * chunk is consisted of nr_cpu_ids units and the first chunk is used
+ * for static percpu variables in the kernel image (special boot time
+ * alloc/init handling necessary as these areas need to be brought up
+ * before allocation services are running).  Unit grows as necessary
+ * and all units grow or shrink in unison.  When a chunk is filled up,
+ * another chunk is allocated.  ie. in vmalloc area
  *
  *  c0                           c1                         c2
  *  -------------------          -------------------        ------------
@@ -558,7 +558,7 @@ static void pcpu_free_area(struct pcpu_chunk *chunk, int freeme)
 static void pcpu_unmap(struct pcpu_chunk *chunk, int page_start, int page_end,
 		       bool flush_tlb)
 {
-	unsigned int last = num_possible_cpus() - 1;
+	unsigned int last = nr_cpu_ids - 1;
 	unsigned int cpu;
 
 	/* unmap must not be done on immutable chunk */
@@ -643,7 +643,7 @@ static void pcpu_depopulate_chunk(struct pcpu_chunk *chunk, int off, int size,
  */
 static int pcpu_map(struct pcpu_chunk *chunk, int page_start, int page_end)
 {
-	unsigned int last = num_possible_cpus() - 1;
+	unsigned int last = nr_cpu_ids - 1;
 	unsigned int cpu;
 	int err;
 
@@ -1067,9 +1067,9 @@ size_t __init pcpu_setup_first_chunk(pcpu_get_page_fn_t get_page_fn,
 					PFN_UP(size_sum));
 
 	pcpu_unit_size = pcpu_unit_pages << PAGE_SHIFT;
-	pcpu_chunk_size = num_possible_cpus() * pcpu_unit_size;
+	pcpu_chunk_size = nr_cpu_ids * pcpu_unit_size;
 	pcpu_chunk_struct_size = sizeof(struct pcpu_chunk)
-		+ num_possible_cpus() * pcpu_unit_pages * sizeof(struct page *);
+		+ nr_cpu_ids * pcpu_unit_pages * sizeof(struct page *);
 
 	if (dyn_size < 0)
 		dyn_size = pcpu_unit_size - static_size - reserved_size;
@@ -1248,7 +1248,7 @@ ssize_t __init pcpu_embed_first_chunk(size_t static_size, size_t reserved_size,
 	} else
 		pcpue_unit_size = max_t(size_t, pcpue_size, PCPU_MIN_UNIT_SIZE);
 
-	chunk_size = pcpue_unit_size * num_possible_cpus();
+	chunk_size = pcpue_unit_size * nr_cpu_ids;
 
 	pcpue_ptr = __alloc_bootmem_nopanic(chunk_size, PAGE_SIZE,
 					    __pa(MAX_DMA_ADDRESS));
@@ -1259,12 +1259,15 @@ ssize_t __init pcpu_embed_first_chunk(size_t static_size, size_t reserved_size,
 	}
 
 	/* return the leftover and copy */
-	for_each_possible_cpu(cpu) {
+	for (cpu = 0; cpu < nr_cpu_ids; cpu++) {
 		void *ptr = pcpue_ptr + cpu * pcpue_unit_size;
 
-		free_bootmem(__pa(ptr + pcpue_size),
-			     pcpue_unit_size - pcpue_size);
-		memcpy(ptr, __per_cpu_load, static_size);
+		if (cpu_possible(cpu)) {
+			free_bootmem(__pa(ptr + pcpue_size),
+				     pcpue_unit_size - pcpue_size);
+			memcpy(ptr, __per_cpu_load, static_size);
+		} else
+			free_bootmem(__pa(ptr), pcpue_unit_size);
 	}
 
 	/* we're ready, commit */
-- 
GitLab


From 142d44b0dd6741a64a7bdbe029110e7c1dcf1d23 Mon Sep 17 00:00:00 2001
From: Amerigo Wang <amwang@redhat.com>
Date: Thu, 13 Aug 2009 02:00:13 -0400
Subject: [PATCH 0878/1153] percpu: use the right flag for get_vm_area()

get_vm_area() only accepts VM_* flags, not GFP_*.

And according to the doc of get_vm_area(), here should be
VM_ALLOC.

Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
---
 mm/percpu.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/mm/percpu.c b/mm/percpu.c
index e0be1146f61..5fe37842e0e 100644
--- a/mm/percpu.c
+++ b/mm/percpu.c
@@ -749,7 +749,7 @@ static struct pcpu_chunk *alloc_pcpu_chunk(void)
 	chunk->map[chunk->map_used++] = pcpu_unit_size;
 	chunk->page = chunk->page_ar;
 
-	chunk->vm = get_vm_area(pcpu_chunk_size, GFP_KERNEL);
+	chunk->vm = get_vm_area(pcpu_chunk_size, VM_ALLOC);
 	if (!chunk->vm) {
 		free_pcpu_chunk(chunk);
 		return NULL;
-- 
GitLab


From 563abb4be1a79e7b64784d43beb9d0cacb1bad6f Mon Sep 17 00:00:00 2001
From: Valentin Longchamp <valentin.longchamp@epfl.ch>
Date: Tue, 11 Aug 2009 17:29:21 +0200
Subject: [PATCH 0879/1153] mx31moboard: invert sdhc ro signal sense

Small confusion with our hardware engineer, the WP signal (RO) is
active low on our boards, the signal has to inverted.

This is a pretty straightforward patch, it could even go to -rc,
but if not, then push it for 2.6.32.

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-mx3/mx31moboard-devboard.c | 2 +-
 arch/arm/mach-mx3/mx31moboard-marxbot.c  | 2 +-
 arch/arm/mach-mx3/mx31moboard.c          | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-mx3/mx31moboard-devboard.c b/arch/arm/mach-mx3/mx31moboard-devboard.c
index 4704405165a..b48581e7ded 100644
--- a/arch/arm/mach-mx3/mx31moboard-devboard.c
+++ b/arch/arm/mach-mx3/mx31moboard-devboard.c
@@ -63,7 +63,7 @@ static struct imxuart_platform_data uart_pdata = {
 
 static int devboard_sdhc2_get_ro(struct device *dev)
 {
-	return gpio_get_value(SDHC2_WP);
+	return !gpio_get_value(SDHC2_WP);
 }
 
 static int devboard_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
diff --git a/arch/arm/mach-mx3/mx31moboard-marxbot.c b/arch/arm/mach-mx3/mx31moboard-marxbot.c
index 641c3d6153a..901fb0166c0 100644
--- a/arch/arm/mach-mx3/mx31moboard-marxbot.c
+++ b/arch/arm/mach-mx3/mx31moboard-marxbot.c
@@ -67,7 +67,7 @@ static unsigned int marxbot_pins[] = {
 
 static int marxbot_sdhc2_get_ro(struct device *dev)
 {
-	return gpio_get_value(SDHC2_WP);
+	return !gpio_get_value(SDHC2_WP);
 }
 
 static int marxbot_sdhc2_init(struct device *dev, irq_handler_t detect_irq,
diff --git a/arch/arm/mach-mx3/mx31moboard.c b/arch/arm/mach-mx3/mx31moboard.c
index a17f2e41160..2a2da4739ec 100644
--- a/arch/arm/mach-mx3/mx31moboard.c
+++ b/arch/arm/mach-mx3/mx31moboard.c
@@ -94,7 +94,7 @@ static struct imxi2c_platform_data moboard_i2c1_pdata = {
 
 static int moboard_sdhc1_get_ro(struct device *dev)
 {
-	return gpio_get_value(SDHC1_WP);
+	return !gpio_get_value(SDHC1_WP);
 }
 
 static int moboard_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
-- 
GitLab


From d7e623da1a757fbd8c117fa29190ca8bef14dab3 Mon Sep 17 00:00:00 2001
From: Steven Whitehouse <swhiteho@redhat.com>
Date: Tue, 11 Aug 2009 11:20:11 +0100
Subject: [PATCH 0880/1153] GFS2: Fix permissions on "recover" file

Although this file is only ever written and not read by
userspace, it seems that the utils are opening this
file O_RDWR, so we need to allow that.

Also fixes the whitespace which seemed to be broken.

Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: David Teigland <teigland@redhat.com>
---
 fs/gfs2/sys.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/fs/gfs2/sys.c b/fs/gfs2/sys.c
index 23419dc3027..a7cbfbd340c 100644
--- a/fs/gfs2/sys.c
+++ b/fs/gfs2/sys.c
@@ -386,16 +386,16 @@ static ssize_t jid_show(struct gfs2_sbd *sdp, char *buf)
 #define GDLM_ATTR(_name,_mode,_show,_store) \
 static struct gfs2_attr gdlm_attr_##_name = __ATTR(_name,_mode,_show,_store)
 
-GDLM_ATTR(proto_name,     0444, proto_name_show,	NULL);
-GDLM_ATTR(block,          0644, block_show,		block_store);
-GDLM_ATTR(withdraw,       0644, withdraw_show,		withdraw_store);
-GDLM_ATTR(id,             0444, lkid_show,		NULL);
-GDLM_ATTR(jid,		  0444, jid_show,		NULL);
-GDLM_ATTR(first,          0444, lkfirst_show,		NULL);
-GDLM_ATTR(first_done,     0444, first_done_show,	NULL);
-GDLM_ATTR(recover,        0200, NULL,			recover_store);
-GDLM_ATTR(recover_done,   0444, recover_done_show,	NULL);
-GDLM_ATTR(recover_status, 0444, recover_status_show,	NULL);
+GDLM_ATTR(proto_name,		0444, proto_name_show,		NULL);
+GDLM_ATTR(block,		0644, block_show,		block_store);
+GDLM_ATTR(withdraw,		0644, withdraw_show,		withdraw_store);
+GDLM_ATTR(id,			0444, lkid_show,		NULL);
+GDLM_ATTR(jid,			0444, jid_show,			NULL);
+GDLM_ATTR(first,		0444, lkfirst_show,		NULL);
+GDLM_ATTR(first_done,		0444, first_done_show,		NULL);
+GDLM_ATTR(recover,		0600, NULL,			recover_store);
+GDLM_ATTR(recover_done,		0444, recover_done_show,	NULL);
+GDLM_ATTR(recover_status,	0444, recover_status_show,	NULL);
 
 static struct attribute *lock_module_attrs[] = {
 	&gdlm_attr_proto_name.attr,
-- 
GitLab


From 6b26dead3ce97d016b57724b01974d5ca5c84bd5 Mon Sep 17 00:00:00 2001
From: Pavel Roskin <proski@gnu.org>
Date: Tue, 4 Aug 2009 17:48:16 -0400
Subject: [PATCH 0881/1153] rt2x00: fix memory corruption in rf cache, add a
 sanity check

Change rt2x00_rf_read() and rt2x00_rf_write() to subtract 1 from the rf
register number.  This is needed because the rf registers are enumerated
starting with one.  The size of the rf register cache is just enough to
hold all registers, so writing to the highest register was corrupting
memory.  Add a check to make sure that the rf register number is valid.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@kernel.org
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/rt2x00/rt2x00.h | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/rt2x00/rt2x00.h b/drivers/net/wireless/rt2x00/rt2x00.h
index a498dde024e..49c9e2c1433 100644
--- a/drivers/net/wireless/rt2x00/rt2x00.h
+++ b/drivers/net/wireless/rt2x00/rt2x00.h
@@ -849,13 +849,15 @@ struct rt2x00_dev {
 static inline void rt2x00_rf_read(struct rt2x00_dev *rt2x00dev,
 				  const unsigned int word, u32 *data)
 {
-	*data = rt2x00dev->rf[word];
+	BUG_ON(word < 1 || word > rt2x00dev->ops->rf_size / sizeof(u32));
+	*data = rt2x00dev->rf[word - 1];
 }
 
 static inline void rt2x00_rf_write(struct rt2x00_dev *rt2x00dev,
 				   const unsigned int word, u32 data)
 {
-	rt2x00dev->rf[word] = data;
+	BUG_ON(word < 1 || word > rt2x00dev->ops->rf_size / sizeof(u32));
+	rt2x00dev->rf[word - 1] = data;
 }
 
 /*
-- 
GitLab


From 388ce4beb7135722c584b0af18f215e3ec657adf Mon Sep 17 00:00:00 2001
From: "Kashyap, Desai" <kashyap.desai@lsi.com>
Date: Fri, 14 Aug 2009 15:01:35 +0530
Subject: [PATCH 0882/1153] [SCSI] mpt2sas: fix config request and diag reset
 deadlock

Moving the setting and clearing of the mutex's to
_config_request. There was a mutex deadlock when diag reset is called from
inside _config_request, so diag reset was moved to outside the mutexs.

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
---
 drivers/scsi/mpt2sas/mpt2sas_config.c | 85 +++++++--------------------
 1 file changed, 20 insertions(+), 65 deletions(-)

diff --git a/drivers/scsi/mpt2sas/mpt2sas_config.c b/drivers/scsi/mpt2sas/mpt2sas_config.c
index 1c6658c6023..6ddee161beb 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_config.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_config.c
@@ -236,12 +236,14 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t
 	Mpi2ConfigRequest_t *config_request;
 	int r;
 	u8 retry_count;
-	u8 issue_reset;
+	u8 issue_host_reset = 0;
 	u16 wait_state_count;
 
+	mutex_lock(&ioc->config_cmds.mutex);
 	if (ioc->config_cmds.status != MPT2_CMD_NOT_USED) {
 		printk(MPT2SAS_ERR_FMT "%s: config_cmd in use\n",
 		    ioc->name, __func__);
+		mutex_unlock(&ioc->config_cmds.mutex);
 		return -EAGAIN;
 	}
 	retry_count = 0;
@@ -260,8 +262,8 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t
 			printk(MPT2SAS_ERR_FMT
 			    "%s: failed due to ioc not operational\n",
 			    ioc->name, __func__);
-			ioc->config_cmds.status = MPT2_CMD_NOT_USED;
-			return -EFAULT;
+			r = -EFAULT;
+			goto out;
 		}
 		ssleep(1);
 		ioc_state = mpt2sas_base_get_iocstate(ioc, 1);
@@ -277,8 +279,8 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t
 	if (!smid) {
 		printk(MPT2SAS_ERR_FMT "%s: failed obtaining a smid\n",
 		    ioc->name, __func__);
-		ioc->config_cmds.status = MPT2_CMD_NOT_USED;
-		return -EAGAIN;
+		r = -EAGAIN;
+		goto out;
 	}
 
 	r = 0;
@@ -298,9 +300,15 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t
 		    ioc->name, __func__);
 		_debug_dump_mf(mpi_request,
 		    sizeof(Mpi2ConfigRequest_t)/4);
-		if (!(ioc->config_cmds.status & MPT2_CMD_RESET))
-			issue_reset = 1;
-		goto issue_host_reset;
+		retry_count++;
+		if (ioc->config_cmds.smid == smid)
+			mpt2sas_base_free_smid(ioc, smid);
+		if ((ioc->shost_recovery) ||
+		    (ioc->config_cmds.status & MPT2_CMD_RESET))
+			goto retry_config;
+		issue_host_reset = 1;
+		r = -EFAULT;
+		goto out;
 	}
 	if (ioc->config_cmds.status & MPT2_CMD_REPLY_VALID)
 		memcpy(mpi_reply, ioc->config_cmds.reply,
@@ -308,21 +316,13 @@ _config_request(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigRequest_t
 	if (retry_count)
 		printk(MPT2SAS_INFO_FMT "%s: retry completed!!\n",
 		    ioc->name, __func__);
+out:
 	ioc->config_cmds.status = MPT2_CMD_NOT_USED;
-	return r;
-
- issue_host_reset:
-	if (issue_reset)
+	mutex_unlock(&ioc->config_cmds.mutex);
+	if (issue_host_reset)
 		mpt2sas_base_hard_reset_handler(ioc, CAN_SLEEP,
 		    FORCE_BIG_HAMMER);
-	ioc->config_cmds.status = MPT2_CMD_NOT_USED;
-	if (!retry_count) {
-		printk(MPT2SAS_INFO_FMT "%s: attempting retry\n",
-		    ioc->name, __func__);
-		retry_count++;
-		goto retry_config;
-	}
-	return -EFAULT;
+	return r;
 }
 
 /**
@@ -381,7 +381,6 @@ mpt2sas_config_get_manufacturing_pg0(struct MPT2SAS_ADAPTER *ioc,
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2ManufacturingPage0_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -423,7 +422,6 @@ mpt2sas_config_get_manufacturing_pg0(struct MPT2SAS_ADAPTER *ioc,
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -444,7 +442,6 @@ mpt2sas_config_get_bios_pg2(struct MPT2SAS_ADAPTER *ioc,
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2BiosPage2_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -486,7 +483,6 @@ mpt2sas_config_get_bios_pg2(struct MPT2SAS_ADAPTER *ioc,
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -507,7 +503,6 @@ mpt2sas_config_get_bios_pg3(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2BiosPage3_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -549,7 +544,6 @@ mpt2sas_config_get_bios_pg3(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -570,7 +564,6 @@ mpt2sas_config_get_iounit_pg0(struct MPT2SAS_ADAPTER *ioc,
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2IOUnitPage0_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -612,7 +605,6 @@ mpt2sas_config_get_iounit_pg0(struct MPT2SAS_ADAPTER *ioc,
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -633,7 +625,6 @@ mpt2sas_config_get_iounit_pg1(struct MPT2SAS_ADAPTER *ioc,
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2IOUnitPage1_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -675,7 +666,6 @@ mpt2sas_config_get_iounit_pg1(struct MPT2SAS_ADAPTER *ioc,
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -696,7 +686,6 @@ mpt2sas_config_set_iounit_pg1(struct MPT2SAS_ADAPTER *ioc,
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
 	mpi_request.Action = MPI2_CONFIG_ACTION_PAGE_HEADER;
@@ -738,7 +727,6 @@ mpt2sas_config_set_iounit_pg1(struct MPT2SAS_ADAPTER *ioc,
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -759,7 +747,6 @@ mpt2sas_config_get_ioc_pg8(struct MPT2SAS_ADAPTER *ioc,
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2IOCPage8_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -801,7 +788,6 @@ mpt2sas_config_get_ioc_pg8(struct MPT2SAS_ADAPTER *ioc,
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -824,7 +810,6 @@ mpt2sas_config_get_sas_device_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2SasDevicePage0_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -869,7 +854,6 @@ mpt2sas_config_get_sas_device_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -892,7 +876,6 @@ mpt2sas_config_get_sas_device_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2SasDevicePage1_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -937,7 +920,6 @@ mpt2sas_config_get_sas_device_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -959,7 +941,6 @@ mpt2sas_config_get_number_hba_phys(struct MPT2SAS_ADAPTER *ioc, u8 *num_phys)
 	Mpi2ConfigReply_t mpi_reply;
 	Mpi2SasIOUnitPage0_t config_page;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
 	mpi_request.Action = MPI2_CONFIG_ACTION_PAGE_HEADER;
@@ -1008,7 +989,6 @@ mpt2sas_config_get_number_hba_phys(struct MPT2SAS_ADAPTER *ioc, u8 *num_phys)
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1032,8 +1012,6 @@ mpt2sas_config_get_sas_iounit_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	Mpi2ConfigRequest_t mpi_request;
 	int r;
 	struct config_request mem;
-
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sz);
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1076,7 +1054,6 @@ mpt2sas_config_get_sas_iounit_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1101,7 +1078,6 @@ mpt2sas_config_get_sas_iounit_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sz);
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1144,7 +1120,6 @@ mpt2sas_config_get_sas_iounit_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1167,7 +1142,6 @@ mpt2sas_config_get_expander_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2ExpanderPage0_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1212,7 +1186,6 @@ mpt2sas_config_get_expander_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1236,7 +1209,6 @@ mpt2sas_config_get_expander_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2ExpanderPage1_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1283,7 +1255,6 @@ mpt2sas_config_get_expander_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1306,7 +1277,6 @@ mpt2sas_config_get_enclosure_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2SasEnclosurePage0_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1351,7 +1321,6 @@ mpt2sas_config_get_enclosure_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1373,7 +1342,6 @@ mpt2sas_config_get_phy_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2SasPhyPage0_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1419,7 +1387,6 @@ mpt2sas_config_get_phy_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1441,7 +1408,6 @@ mpt2sas_config_get_phy_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2SasPhyPage1_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1487,7 +1453,6 @@ mpt2sas_config_get_phy_pg1(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1511,7 +1476,6 @@ mpt2sas_config_get_raid_volume_pg1(struct MPT2SAS_ADAPTER *ioc,
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(config_page, 0, sizeof(Mpi2RaidVolPage1_t));
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1554,7 +1518,6 @@ mpt2sas_config_get_raid_volume_pg1(struct MPT2SAS_ADAPTER *ioc,
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1578,7 +1541,6 @@ mpt2sas_config_get_number_pds(struct MPT2SAS_ADAPTER *ioc, u16 handle,
 	struct config_request mem;
 	u16 ioc_status;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	*num_pds = 0;
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1626,7 +1588,6 @@ mpt2sas_config_get_number_pds(struct MPT2SAS_ADAPTER *ioc, u16 handle,
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1651,7 +1612,6 @@ mpt2sas_config_get_raid_volume_pg0(struct MPT2SAS_ADAPTER *ioc,
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	memset(config_page, 0, sz);
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1693,7 +1653,6 @@ mpt2sas_config_get_raid_volume_pg0(struct MPT2SAS_ADAPTER *ioc,
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1717,7 +1676,6 @@ mpt2sas_config_get_phys_disk_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 	int r;
 	struct config_request mem;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	memset(config_page, 0, sizeof(Mpi2RaidPhysDiskPage0_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1760,7 +1718,6 @@ mpt2sas_config_get_phys_disk_pg0(struct MPT2SAS_ADAPTER *ioc, Mpi2ConfigReply_t
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
@@ -1784,7 +1741,6 @@ mpt2sas_config_get_volume_handle(struct MPT2SAS_ADAPTER *ioc, u16 pd_handle,
 	struct config_request mem;
 	u16 ioc_status;
 
-	mutex_lock(&ioc->config_cmds.mutex);
 	*volume_handle = 0;
 	memset(&mpi_request, 0, sizeof(Mpi2ConfigRequest_t));
 	mpi_request.Function = MPI2_FUNCTION_CONFIG;
@@ -1848,7 +1804,6 @@ mpt2sas_config_get_volume_handle(struct MPT2SAS_ADAPTER *ioc, u16 pd_handle,
 		_config_free_config_dma_memory(ioc, &mem);
 
  out:
-	mutex_unlock(&ioc->config_cmds.mutex);
 	return r;
 }
 
-- 
GitLab


From 0527a1a8440a20b3d0fd1d0c9e75a6f38a9d5315 Mon Sep 17 00:00:00 2001
From: roel kluin <roel.kluin@gmail.com>
Date: Fri, 14 Aug 2009 02:09:56 +0000
Subject: [PATCH 0883/1153] via-velocity: Fix test of mii_status bit
 VELOCITY_DUPLEX_FULL

Test whether VELOCITY_DUPLEX_FULL bit is set in mii_status.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/via-velocity.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/via-velocity.c b/drivers/net/via-velocity.c
index 3ba35956327..cee08a1e497 100644
--- a/drivers/net/via-velocity.c
+++ b/drivers/net/via-velocity.c
@@ -1778,7 +1778,7 @@ static void velocity_error(struct velocity_info *vptr, int status)
 			 *	 mode
 			 */
 			if (vptr->rev_id < REV_ID_VT3216_A0) {
-				if (vptr->mii_status | VELOCITY_DUPLEX_FULL)
+				if (vptr->mii_status & VELOCITY_DUPLEX_FULL)
 					BYTE_REG_BITS_ON(TCR_TB2BDIS, &regs->TCR);
 				else
 					BYTE_REG_BITS_OFF(TCR_TB2BDIS, &regs->TCR);
-- 
GitLab


From 22580f894ac190c46beebb5c3172e450a2318f79 Mon Sep 17 00:00:00 2001
From: Dongdong Deng <dongdong.deng@windriver.com>
Date: Thu, 13 Aug 2009 19:12:31 +0000
Subject: [PATCH 0884/1153] drivers/net: fixed drivers that support netpoll use
 ndo_start_xmit()

The NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb(). The use of spin_lock_irq() and spin_unlock_irq()
in the NETPOLL API callbacks causes the interrupts to get enabled and
can lead to kernel instability.

The solution is to use spin_lock_irqsave() and spin_unlock_restore()
to prevent the irqs from getting enabled while in netpoll_send_skb().

Call trace:
netpoll_send_skb()
{
   -> local_irq_save(flags)
     ---> dev->ndo_start_xmit(skb, dev)
         ---> spin_lock_irq()
         ---> spin_unlock_irq() *******here would enable the interrupt.
              ...
   -> local_irq_restore(flags)
}

Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/b44.c              | 5 +++--
 drivers/net/tulip/tulip_core.c | 5 +++--
 drivers/net/ucc_geth.c         | 5 +++--
 drivers/net/via-rhine.c        | 5 +++--
 4 files changed, 12 insertions(+), 8 deletions(-)

diff --git a/drivers/net/b44.c b/drivers/net/b44.c
index 36d4d377ec2..bafca672ea7 100644
--- a/drivers/net/b44.c
+++ b/drivers/net/b44.c
@@ -952,9 +952,10 @@ static int b44_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	int rc = NETDEV_TX_OK;
 	dma_addr_t mapping;
 	u32 len, entry, ctrl;
+	unsigned long flags;
 
 	len = skb->len;
-	spin_lock_irq(&bp->lock);
+	spin_lock_irqsave(&bp->lock, flags);
 
 	/* This is a hard error, log it. */
 	if (unlikely(TX_BUFFS_AVAIL(bp) < 1)) {
@@ -1027,7 +1028,7 @@ static int b44_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	dev->trans_start = jiffies;
 
 out_unlock:
-	spin_unlock_irq(&bp->lock);
+	spin_unlock_irqrestore(&bp->lock, flags);
 
 	return rc;
 
diff --git a/drivers/net/tulip/tulip_core.c b/drivers/net/tulip/tulip_core.c
index 99a63649f4f..4cf9a658875 100644
--- a/drivers/net/tulip/tulip_core.c
+++ b/drivers/net/tulip/tulip_core.c
@@ -652,8 +652,9 @@ tulip_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	int entry;
 	u32 flag;
 	dma_addr_t mapping;
+	unsigned long flags;
 
-	spin_lock_irq(&tp->lock);
+	spin_lock_irqsave(&tp->lock, flags);
 
 	/* Calculate the next Tx descriptor entry. */
 	entry = tp->cur_tx % TX_RING_SIZE;
@@ -688,7 +689,7 @@ tulip_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	/* Trigger an immediate transmit demand. */
 	iowrite32(0, tp->base_addr + CSR1);
 
-	spin_unlock_irq(&tp->lock);
+	spin_unlock_irqrestore(&tp->lock, flags);
 
 	dev->trans_start = jiffies;
 
diff --git a/drivers/net/ucc_geth.c b/drivers/net/ucc_geth.c
index 3b957e6412e..8a7b8c7bd78 100644
--- a/drivers/net/ucc_geth.c
+++ b/drivers/net/ucc_geth.c
@@ -3111,10 +3111,11 @@ static int ucc_geth_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	u8 __iomem *bd;			/* BD pointer */
 	u32 bd_status;
 	u8 txQ = 0;
+	unsigned long flags;
 
 	ugeth_vdbg("%s: IN", __func__);
 
-	spin_lock_irq(&ugeth->lock);
+	spin_lock_irqsave(&ugeth->lock, flags);
 
 	dev->stats.tx_bytes += skb->len;
 
@@ -3171,7 +3172,7 @@ static int ucc_geth_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	uccf = ugeth->uccf;
 	out_be16(uccf->p_utodr, UCC_FAST_TOD);
 #endif
-	spin_unlock_irq(&ugeth->lock);
+	spin_unlock_irqrestore(&ugeth->lock, flags);
 
 	return 0;
 }
diff --git a/drivers/net/via-rhine.c b/drivers/net/via-rhine.c
index 88c30a58b4b..934f7671650 100644
--- a/drivers/net/via-rhine.c
+++ b/drivers/net/via-rhine.c
@@ -1218,6 +1218,7 @@ static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev)
 	struct rhine_private *rp = netdev_priv(dev);
 	void __iomem *ioaddr = rp->base;
 	unsigned entry;
+	unsigned long flags;
 
 	/* Caution: the write order is important here, set the field
 	   with the "ownership" bits last. */
@@ -1261,7 +1262,7 @@ static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev)
 		cpu_to_le32(TXDESC | (skb->len >= ETH_ZLEN ? skb->len : ETH_ZLEN));
 
 	/* lock eth irq */
-	spin_lock_irq(&rp->lock);
+	spin_lock_irqsave(&rp->lock, flags);
 	wmb();
 	rp->tx_ring[entry].tx_status = cpu_to_le32(DescOwn);
 	wmb();
@@ -1280,7 +1281,7 @@ static int rhine_start_tx(struct sk_buff *skb, struct net_device *dev)
 
 	dev->trans_start = jiffies;
 
-	spin_unlock_irq(&rp->lock);
+	spin_unlock_irqrestore(&rp->lock, flags);
 
 	if (debug > 4) {
 		printk(KERN_DEBUG "%s: Transmit frame #%d queued in slot %d.\n",
-- 
GitLab


From 7c1d15d736687057f4dc6e51fbf44b6f6e4320cb Mon Sep 17 00:00:00 2001
From: Petko Manolov <petkan@nucleusys.com>
Date: Fri, 14 Aug 2009 06:40:48 +0000
Subject: [PATCH 0885/1153] pegasus: Add new device ID.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Add new definition to 'pegasus.h' for support Japanese IO DATA
"ETX-US2" USB Ethernet Adapter.

PEGASUS_DEV( $B!H(BIO DATA USB ETX-US2$B!I(B, VENDOR_IODATA, 0x092a,
DEFAULT_GPIO_RESET | PEGASUS_II )

Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/usb/pegasus.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/usb/pegasus.h b/drivers/net/usb/pegasus.h
index c7467823cd1..f968c834ff6 100644
--- a/drivers/net/usb/pegasus.h
+++ b/drivers/net/usb/pegasus.h
@@ -250,6 +250,8 @@ PEGASUS_DEV( "IO DATA USB ET/TX", VENDOR_IODATA, 0x0904,
 		DEFAULT_GPIO_RESET )
 PEGASUS_DEV( "IO DATA USB ET/TX-S", VENDOR_IODATA, 0x0913,
 		DEFAULT_GPIO_RESET | PEGASUS_II )
+PEGASUS_DEV( "IO DATA USB ETX-US2", VENDOR_IODATA, 0x092a,
+		DEFAULT_GPIO_RESET | PEGASUS_II )
 PEGASUS_DEV( "Kingston KNU101TX Ethernet", VENDOR_KINGSTON, 0x000a,
 		DEFAULT_GPIO_RESET)
 PEGASUS_DEV( "LANEED USB Ethernet LD-USB/TX", VENDOR_LANEED, 0x4002,
-- 
GitLab


From 8cdb045632e5ee22854538619ac6f150eb0a4894 Mon Sep 17 00:00:00 2001
From: Tom Goff <thomas.goff@boeing.com>
Date: Fri, 14 Aug 2009 16:33:56 -0700
Subject: [PATCH 0886/1153] gre: Fix MTU calculation for bound GRE tunnels

The GRE header length should be subtracted when the tunnel MTU is
calculated.  This just corrects for the associativity change
introduced by commit 42aa916265d740d66ac1f17290366e9494c884c2
("gre: Move MTU setting out of ipgre_tunnel_bind_dev").

Signed-off-by: Tom Goff <thomas.goff@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/ipv4/ip_gre.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/ipv4/ip_gre.c b/net/ipv4/ip_gre.c
index cb4a0f4bd5e..82c11dd10a6 100644
--- a/net/ipv4/ip_gre.c
+++ b/net/ipv4/ip_gre.c
@@ -951,7 +951,7 @@ static int ipgre_tunnel_bind_dev(struct net_device *dev)
 			addend += 4;
 	}
 	dev->needed_headroom = addend + hlen;
-	mtu -= dev->hard_header_len - addend;
+	mtu -= dev->hard_header_len + addend;
 
 	if (mtu < 68)
 		mtu = 68;
-- 
GitLab


From 616b8434688aa08bd6f019cc60c8dfe121e9e5ae Mon Sep 17 00:00:00 2001
From: Jerome Glisse <jglisse@redhat.com>
Date: Thu, 6 Aug 2009 17:47:24 +0200
Subject: [PATCH 0887/1153] drm/radeon/kms: Add specific rs690 authorized
 register table

rs690 is r3xx 3D engine with AVIVO modesetting so we need to allow
AVIVO register for vline synchronization. This add a specific table
to rs690 to handle that. Thanks to Marc (marvin24) for debugging
this and kudos to Andre (taiu1) for spotting the origin of the bugs.

Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_asic.h |  3 +-
 drivers/gpu/drm/radeon/rs690.c       | 65 ++++++++++++++++++++++++++++
 2 files changed, 67 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h
index 9a75876e0c3..c0ae2d92325 100644
--- a/drivers/gpu/drm/radeon/radeon_asic.h
+++ b/drivers/gpu/drm/radeon/radeon_asic.h
@@ -308,6 +308,7 @@ static struct radeon_asic rs600_asic = {
 /*
  * rs690,rs740
  */
+int rs690_init(struct radeon_device *rdev);
 void rs690_errata(struct radeon_device *rdev);
 void rs690_vram_info(struct radeon_device *rdev);
 int rs690_mc_init(struct radeon_device *rdev);
@@ -316,7 +317,7 @@ uint32_t rs690_mc_rreg(struct radeon_device *rdev, uint32_t reg);
 void rs690_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v);
 void rs690_bandwidth_update(struct radeon_device *rdev);
 static struct radeon_asic rs690_asic = {
-	.init = &r300_init,
+	.init = &rs690_init,
 	.errata = &rs690_errata,
 	.vram_info = &rs690_vram_info,
 	.gpu_reset = &r300_gpu_reset,
diff --git a/drivers/gpu/drm/radeon/rs690.c b/drivers/gpu/drm/radeon/rs690.c
index 839595b0072..bc6b7c5339b 100644
--- a/drivers/gpu/drm/radeon/rs690.c
+++ b/drivers/gpu/drm/radeon/rs690.c
@@ -652,3 +652,68 @@ void rs690_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
 	WREG32(RS690_MC_DATA, v);
 	WREG32(RS690_MC_INDEX, RS690_MC_INDEX_WR_ACK);
 }
+
+static const unsigned rs690_reg_safe_bm[219] = {
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0x17FF1FFF,0xFFFFFFFC,0xFFFFFFFF,0xFF30FFBF,
+	0xFFFFFFF8,0xC3E6FFFF,0xFFFFF6DF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFF03F,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFEFCE,0xF00EBFFF,0x007C0000,
+	0xF0000078,0xFF000009,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFF7FF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFC78,0xFFFFFFFF,0xFFFFFFFE,0xFFFFFFFF,
+	0x38FF8F50,0xFFF88082,0xF000000C,0xFAE009FF,
+	0x0000FFFF,0xFFFFFFFF,0xFFFFFFFF,0x00000000,
+	0x00000000,0x0000C100,0x00000000,0x00000000,
+	0x00000000,0x00000000,0x00000000,0x00000000,
+	0x00000000,0xFFFF0000,0xFFFFFFFF,0xFF80FFFF,
+	0x00000000,0x00000000,0x00000000,0x00000000,
+	0x0003FC01,0xFFFFFFF8,0xFE800B19,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+	0xFFFFFFFF,0xFFFFFFFF,0xFFFFFFFF,
+};
+
+int rs690_init(struct radeon_device *rdev)
+{
+	rdev->config.r300.reg_safe_bm = rs690_reg_safe_bm;
+	rdev->config.r300.reg_safe_bm_size = ARRAY_SIZE(rs690_reg_safe_bm);
+	return 0;
+}
-- 
GitLab


From ebb177d2afb8532a8a316489aed545ed0c170802 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Sat, 15 Aug 2009 12:25:08 +1000
Subject: [PATCH 0888/1153] drm/edid: fixup detailed timings like the X server.

this syncs the versioning check with the code the X server uses.

Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/drm_edid.c | 72 ++++++++++++++++++--------------------
 1 file changed, 34 insertions(+), 38 deletions(-)

diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c
index 80cc6d06d61..7f2728bbc16 100644
--- a/drivers/gpu/drm/drm_edid.c
+++ b/drivers/gpu/drm/drm_edid.c
@@ -502,12 +502,40 @@ static int add_detailed_info(struct drm_connector *connector,
 		struct detailed_non_pixel *data = &timing->data.other_data;
 		struct drm_display_mode *newmode;
 
-		/* EDID up to and including 1.2 may put monitor info here */
-		if (edid->version == 1 && edid->revision < 3)
-			continue;
-
-		/* Detailed mode timing */
-		if (timing->pixel_clock) {
+		/* X server check is version 1.1 or higher */
+		if (edid->version == 1 && edid->revision >= 1 &&
+		    !timing->pixel_clock) {
+			/* Other timing or info */
+			switch (data->type) {
+			case EDID_DETAIL_MONITOR_SERIAL:
+				break;
+			case EDID_DETAIL_MONITOR_STRING:
+				break;
+			case EDID_DETAIL_MONITOR_RANGE:
+				/* Get monitor range data */
+				break;
+			case EDID_DETAIL_MONITOR_NAME:
+				break;
+			case EDID_DETAIL_MONITOR_CPDATA:
+				break;
+			case EDID_DETAIL_STD_MODES:
+				/* Five modes per detailed section */
+				for (j = 0; j < 5; i++) {
+					struct std_timing *std;
+					struct drm_display_mode *newmode;
+
+					std = &data->data.timings[j];
+					newmode = drm_mode_std(dev, std);
+					if (newmode) {
+						drm_mode_probed_add(connector, newmode);
+						modes++;
+					}
+				}
+				break;
+			default:
+				break;
+			}
+		} else {
 			newmode = drm_mode_detailed(dev, edid, timing, quirks);
 			if (!newmode)
 				continue;
@@ -518,38 +546,6 @@ static int add_detailed_info(struct drm_connector *connector,
 			drm_mode_probed_add(connector, newmode);
 
 			modes++;
-			continue;
-		}
-
-		/* Other timing or info */
-		switch (data->type) {
-		case EDID_DETAIL_MONITOR_SERIAL:
-			break;
-		case EDID_DETAIL_MONITOR_STRING:
-			break;
-		case EDID_DETAIL_MONITOR_RANGE:
-			/* Get monitor range data */
-			break;
-		case EDID_DETAIL_MONITOR_NAME:
-			break;
-		case EDID_DETAIL_MONITOR_CPDATA:
-			break;
-		case EDID_DETAIL_STD_MODES:
-			/* Five modes per detailed section */
-			for (j = 0; j < 5; i++) {
-				struct std_timing *std;
-				struct drm_display_mode *newmode;
-
-				std = &data->data.timings[j];
-				newmode = drm_mode_std(dev, std);
-				if (newmode) {
-					drm_mode_probed_add(connector, newmode);
-					modes++;
-				}
-			}
-			break;
-		default:
-			break;
 		}
 	}
 
-- 
GitLab


From 21bc1f024d0d4ea43fc0f2a43504e759261c7b18 Mon Sep 17 00:00:00 2001
From: Magnus Damm <damm@igel.co.jp>
Date: Sat, 15 Aug 2009 02:53:16 +0000
Subject: [PATCH 0889/1153] sh: skip disabled LCDC channels

This patch updates the SuperH Mobile LCDC driver to skip
over disabled channels. Without this patch suspend-to-ram
operation will crash if deferred io is enabled.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
---
 drivers/video/sh_mobile_lcdcfb.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/video/sh_mobile_lcdcfb.c b/drivers/video/sh_mobile_lcdcfb.c
index 8f24564f77b..07f22b62563 100644
--- a/drivers/video/sh_mobile_lcdcfb.c
+++ b/drivers/video/sh_mobile_lcdcfb.c
@@ -481,6 +481,9 @@ static int sh_mobile_lcdc_start(struct sh_mobile_lcdc_priv *priv)
 	/* tell the board code to enable the panel */
 	for (k = 0; k < ARRAY_SIZE(priv->ch); k++) {
 		ch = &priv->ch[k];
+		if (!ch->enabled)
+			continue;
+
 		board_cfg = &ch->cfg.board_cfg;
 		if (board_cfg->display_on)
 			board_cfg->display_on(board_cfg->board_data);
@@ -498,6 +501,8 @@ static void sh_mobile_lcdc_stop(struct sh_mobile_lcdc_priv *priv)
 	/* clean up deferred io and ask board code to disable panel */
 	for (k = 0; k < ARRAY_SIZE(priv->ch); k++) {
 		ch = &priv->ch[k];
+		if (!ch->enabled)
+			continue;
 
 		/* deferred io mode:
 		 * flush frame, and wait for frame end interrupt
-- 
GitLab


From f6431732f128a241b149c0aa85dfec852455ebf9 Mon Sep 17 00:00:00 2001
From: Magnus Damm <damm@igel.co.jp>
Date: Sat, 15 Aug 2009 02:53:25 +0000
Subject: [PATCH 0890/1153] sh: CMT suspend/resume

This patch updates the SuperH CMT driver with suspend and resume
callbacks for the suspend-to-ram case. This patch stops the CMT
channel at suspend time to avoid unwanted wake up events.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
---
 drivers/clocksource/sh_cmt.c | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/drivers/clocksource/sh_cmt.c b/drivers/clocksource/sh_cmt.c
index 2964f5f4a7e..6b3e0c2f33e 100644
--- a/drivers/clocksource/sh_cmt.c
+++ b/drivers/clocksource/sh_cmt.c
@@ -40,6 +40,7 @@ struct sh_cmt_priv {
 	struct platform_device *pdev;
 
 	unsigned long flags;
+	unsigned long flags_suspend;
 	unsigned long match_value;
 	unsigned long next_match_value;
 	unsigned long max_match_value;
@@ -667,11 +668,38 @@ static int __devexit sh_cmt_remove(struct platform_device *pdev)
 	return -EBUSY; /* cannot unregister clockevent and clocksource */
 }
 
+static int sh_cmt_suspend(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct sh_cmt_priv *p = platform_get_drvdata(pdev);
+
+	/* save flag state and stop CMT channel */
+	p->flags_suspend = p->flags;
+	sh_cmt_stop(p, p->flags);
+	return 0;
+}
+
+static int sh_cmt_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct sh_cmt_priv *p = platform_get_drvdata(pdev);
+
+	/* start CMT channel from saved state */
+	sh_cmt_start(p, p->flags_suspend);
+	return 0;
+}
+
+static struct dev_pm_ops sh_cmt_dev_pm_ops = {
+	.suspend = sh_cmt_suspend,
+	.resume = sh_cmt_resume,
+};
+
 static struct platform_driver sh_cmt_device_driver = {
 	.probe		= sh_cmt_probe,
 	.remove		= __devexit_p(sh_cmt_remove),
 	.driver		= {
 		.name	= "sh_cmt",
+		.pm	= &sh_cmt_dev_pm_ops,
 	}
 };
 
-- 
GitLab


From 9747e78b304b44d6fb73e2c8071406d55aa8bb75 Mon Sep 17 00:00:00 2001
From: Magnus Damm <damm@igel.co.jp>
Date: Sat, 15 Aug 2009 02:53:34 +0000
Subject: [PATCH 0891/1153] sh: use in-soc KEYSC on se7724

This patch updates the Solution Engine 7724 board code to use
in-SoC KEYSC resources for the keyboard platform device. Using
the in-SoC key scan controller fixes a crash-during-resume issue.

Without this patch the KEYSC hardware block located in the board
specific FPGA is used together with an external IRQ which is
routed through the FPGA and handled by some board specific demux
code. This board specific FPGA interrupt code does not implement
desc->set_wake() so the enable_irq_wake() call in the sh_keysc
driver will fail at suspend-to-ram time and the disable_irq_wake()
will bomb out when resuming.

Changing the platform data to use the in-SoC KEYSC hardware makes
the se7724 board support code less special which is a good thing.
Also, the board specific KEYSC pin setup code selects in-SoC pin
functions already which makes the current FPGA platform device data
look like a typo.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
---
 arch/sh/boards/mach-se/7724/setup.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/arch/sh/boards/mach-se/7724/setup.c b/arch/sh/boards/mach-se/7724/setup.c
index 8fed45a2fb8..15456a0773b 100644
--- a/arch/sh/boards/mach-se/7724/setup.c
+++ b/arch/sh/boards/mach-se/7724/setup.c
@@ -238,7 +238,7 @@ static struct platform_device ceu1_device = {
 	},
 };
 
-/* KEYSC */
+/* KEYSC in SoC (Needs SW33-2 set to ON) */
 static struct sh_keysc_info keysc_info = {
 	.mode = SH_KEYSC_MODE_1,
 	.scan_timing = 10,
@@ -255,12 +255,13 @@ static struct sh_keysc_info keysc_info = {
 
 static struct resource keysc_resources[] = {
 	[0] = {
-		.start  = 0x1a204000,
-		.end    = 0x1a20400f,
+		.name	= "KEYSC",
+		.start  = 0x044b0000,
+		.end    = 0x044b000f,
 		.flags  = IORESOURCE_MEM,
 	},
 	[1] = {
-		.start  = IRQ0_KEY,
+		.start  = 79,
 		.flags  = IORESOURCE_IRQ,
 	},
 };
-- 
GitLab


From 237674e050ae8ea40a432412df6c15d60b7ae8a6 Mon Sep 17 00:00:00 2001
From: Magnus Damm <damm@igel.co.jp>
Date: Sat, 15 Aug 2009 02:53:42 +0000
Subject: [PATCH 0892/1153] sh: sh7724 ddr self-refresh changes

This patch updates the SuperH Mobile sleep assembly code with
support for DBSC memory controller found in the sh7724 processor.

Without this fix the memory hooked up to the sh7724 processor
will never enter self-refresh mode before suspending to ram. The
effect of this is that the memory contents most likeley will be
lost upon resume which may or may not be what you want.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
---
 arch/sh/kernel/cpu/shmobile/sleep.S | 70 ++++++++++++++++++++++++++++-
 1 file changed, 68 insertions(+), 2 deletions(-)

diff --git a/arch/sh/kernel/cpu/shmobile/sleep.S b/arch/sh/kernel/cpu/shmobile/sleep.S
index 5d888ef53d8..baf2d7d46b0 100644
--- a/arch/sh/kernel/cpu/shmobile/sleep.S
+++ b/arch/sh/kernel/cpu/shmobile/sleep.S
@@ -26,8 +26,30 @@ ENTRY(sh_mobile_standby)
 
 	tst	#SUSP_SH_SF, r0
 	bt	skip_set_sf
+#ifdef CONFIG_CPU_SUBTYPE_SH7724
+	/* DBSC: put memory in self-refresh mode */
 
-	/* SDRAM: disable power down and put in self-refresh mode */
+	mov.l	dben_reg, r4
+	mov.l	dben_data0, r1
+	mov.l	r1, @r4
+
+	mov.l	dbrfpdn0_reg, r4
+	mov.l	dbrfpdn0_data0, r1
+	mov.l	r1, @r4
+
+	mov.l	dbcmdcnt_reg, r4
+	mov.l	dbcmdcnt_data0, r1
+	mov.l	r1, @r4
+
+	mov.l	dbcmdcnt_reg, r4
+	mov.l	dbcmdcnt_data1, r1
+	mov.l	r1, @r4
+
+	mov.l	dbrfpdn0_reg, r4
+	mov.l	dbrfpdn0_data1, r1
+	mov.l	r1, @r4
+#else
+	/* SBSC: disable power down and put in self-refresh mode */
 	mov.l	1f, r4
 	mov.l	2f, r1
 	mov.l	@r4, r2
@@ -35,6 +57,7 @@ ENTRY(sh_mobile_standby)
 	mov.l   3f, r3
 	and	r3, r2
 	mov.l	r2, @r4
+#endif
 
 skip_set_sf:
 	tst	#SUSP_SH_SLEEP, r0
@@ -84,7 +107,36 @@ done_sleep:
 	tst	#SUSP_SH_SF, r0
 	bt	skip_restore_sf
 
-	/* SDRAM: set auto-refresh mode */
+#ifdef CONFIG_CPU_SUBTYPE_SH7724
+	/* DBSC: put memory in auto-refresh mode */
+
+	mov.l	dbrfpdn0_reg, r4
+	mov.l	dbrfpdn0_data0, r1
+	mov.l	r1, @r4
+
+	/* sleep 140 ns */
+	nop
+	nop
+	nop
+	nop
+
+	mov.l	dbcmdcnt_reg, r4
+	mov.l	dbcmdcnt_data0, r1
+	mov.l	r1, @r4
+
+	mov.l	dbcmdcnt_reg, r4
+	mov.l	dbcmdcnt_data1, r1
+	mov.l	r1, @r4
+
+	mov.l	dben_reg, r4
+	mov.l	dben_data1, r1
+	mov.l	r1, @r4
+
+	mov.l	dbrfpdn0_reg, r4
+	mov.l	dbrfpdn0_data2, r1
+	mov.l	r1, @r4
+#else
+	/* SBSC: set auto-refresh mode */
 	mov.l	1f, r4
 	mov.l	@r4, r2
 	mov.l   4f, r3
@@ -98,15 +150,29 @@ done_sleep:
 	add	r4, r3
 	or	r2, r3
 	mov.l	r3, @r1
+#endif
 skip_restore_sf:
 	rts
 	 nop
 
 	.balign 4
+#ifdef CONFIG_CPU_SUBTYPE_SH7724
+dben_reg:	.long	0xfd000010 /* DBEN */
+dben_data0:	.long	0
+dben_data1:	.long	1
+dbrfpdn0_reg:	.long	0xfd000040 /* DBRFPDN0 */
+dbrfpdn0_data0:	.long	0
+dbrfpdn0_data1:	.long	1
+dbrfpdn0_data2:	.long	0x00010000
+dbcmdcnt_reg:	.long	0xfd000014 /* DBCMDCNT */
+dbcmdcnt_data0:	.long	2
+dbcmdcnt_data1:	.long	4
+#else
 1:	.long	0xfe400008 /* SDCR0 */
 2:	.long	0x00000400
 3:	.long	0xffff7fff
 4:	.long	0xfffffbff
+#endif
 5:	.long	0xa4150020 /* STBCR */
 6:	.long   0xfe40001c /* RTCOR */
 7:	.long   0xfe400018 /* RTCNT */
-- 
GitLab


From 3ef12c3c97603bad405d30c989718cc9405e2759 Mon Sep 17 00:00:00 2001
From: Cliff Wickman <cpw@sgi.com>
Date: Fri, 14 Aug 2009 13:56:37 -0500
Subject: [PATCH 0893/1153] x86: Fix UV BAU destination subnode id

The SGI UV Broadcast Assist Unit is used to send TLB shootdown
messages to remote nodes of the system.  The header of the
message must contain the subnode id of the block in the
receiving hub that handles such messages.  It should always be
0x10, the id of the "LB" block.

It had previously been documented as a "must be zero" field.

Signed-off-by: Cliff Wickman <cpw@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <E1Mc1x7-0005Ce-6t@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/include/asm/uv/uv_bau.h | 2 +-
 arch/x86/kernel/tlb_uv.c         | 1 +
 2 files changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/x86/include/asm/uv/uv_bau.h b/arch/x86/include/asm/uv/uv_bau.h
index bddd44f2f0a..80e2984f521 100644
--- a/arch/x86/include/asm/uv/uv_bau.h
+++ b/arch/x86/include/asm/uv/uv_bau.h
@@ -133,7 +133,7 @@ struct bau_msg_payload {
  * see table 4.2.3.0.1 in broacast_assist spec.
  */
 struct bau_msg_header {
-	unsigned int dest_subnodeid:6;	/* must be zero */
+	unsigned int dest_subnodeid:6;	/* must be 0x10, for the LB */
 	/* bits 5:0 */
 	unsigned int base_dest_nodeid:15; /* nasid>>1 (pnode) of */
 	/* bits 20:6 */			  /* first bit in node_map */
diff --git a/arch/x86/kernel/tlb_uv.c b/arch/x86/kernel/tlb_uv.c
index 8ccabb8a2f6..77b9689f8ed 100644
--- a/arch/x86/kernel/tlb_uv.c
+++ b/arch/x86/kernel/tlb_uv.c
@@ -744,6 +744,7 @@ uv_activation_descriptor_init(int node, int pnode)
 		 * note that base_dest_nodeid is actually a nasid.
 		 */
 		ad2->header.base_dest_nodeid = uv_partition_base_pnode << 1;
+		ad2->header.dest_subnodeid = 0x10; /* the LB */
 		ad2->header.command = UV_NET_ENDPOINT_INTD;
 		ad2->header.int_both = 1;
 		/*
-- 
GitLab


From 39e6dd73502f64e2ae3236b304e160ae30de9384 Mon Sep 17 00:00:00 2001
From: Arnaldo Carvalho de Melo <acme@redhat.com>
Date: Fri, 14 Aug 2009 15:26:32 -0300
Subject: [PATCH 0894/1153] perf record: Fix typo in pid_synthesize_comm_event

We were using 'fd' locally, but there was a global 'fd' too, so
when converting from open to fopen the test made against fd
should be made against 'fp', but since we have that global
it didnt get discovered ...

Reported-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20090814182632.GF3490@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-record.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/tools/perf/builtin-record.c b/tools/perf/builtin-record.c
index 3d051b9cf25..89a5ddcd1de 100644
--- a/tools/perf/builtin-record.c
+++ b/tools/perf/builtin-record.c
@@ -219,7 +219,7 @@ static pid_t pid_synthesize_comm_event(pid_t pid, int full)
 	snprintf(filename, sizeof(filename), "/proc/%d/status", pid);
 
 	fp = fopen(filename, "r");
-	if (fd == NULL) {
+	if (fp == NULL) {
 		/*
 		 * We raced with a task exiting - just return:
 		 */
-- 
GitLab


From dde5828f56cb2c1aa70365c476e6830482127258 Mon Sep 17 00:00:00 2001
From: Russell King <rmk@dyn-67.arm.linux.org.uk>
Date: Sat, 15 Aug 2009 12:36:00 +0100
Subject: [PATCH 0895/1153] ARM: Fix broken highmem support

Currently, highmem is selectable, and you can request an increased
vmalloc area.  However, none of this has any effect on the memory
layout since a patch in the highmem series was accidentally dropped.
Moreover, even if you did want highmem, all memory would still be
registered as lowmem, possibly resulting in overflow of the available
virtual mapping space.

The highmem boundary is determined by the highest allowed beginning
of the vmalloc area, which depends on its configurable minimum size
(see commit 60296c71f6c5063e3c1f1d2619ca0b60940162e7 for details on
this).

We should create mappings and initialize bootmem only for low memory,
while the zone allocator must still be told about highmem.

Currently, memory nodes which are completely located in high memory
are not supported.  This is not a huge limitation since systems
relying on highmem support are unlikely to have discontiguous memory
with large holes.

[ A similar patch was meant to be merged before commit 5f0fbf9ecaf3
  and be available  in Linux v2.6.30, however some git rebase screw-up
  of mine dropped the first commit of the series, and that goofage
  escaped testing somehow as well. -- Nico ]

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
---
 arch/arm/include/asm/setup.h |   3 +-
 arch/arm/mm/init.c           | 118 ++++++++++++++++++++++-------------
 arch/arm/mm/mmu.c            |   9 ++-
 3 files changed, 83 insertions(+), 47 deletions(-)

diff --git a/arch/arm/include/asm/setup.h b/arch/arm/include/asm/setup.h
index ee1304f22f9..5ccce0a9b03 100644
--- a/arch/arm/include/asm/setup.h
+++ b/arch/arm/include/asm/setup.h
@@ -201,7 +201,8 @@ static struct tagtable __tagtable_##fn __tag = { tag, fn }
 struct membank {
 	unsigned long start;
 	unsigned long size;
-	int           node;
+	unsigned short node;
+	unsigned short highmem;
 };
 
 struct meminfo {
diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c
index 8277802ec85..3a7279c1ce5 100644
--- a/arch/arm/mm/init.c
+++ b/arch/arm/mm/init.c
@@ -120,6 +120,32 @@ void show_mem(void)
 	printk("%d pages swap cached\n", cached);
 }
 
+static void __init find_node_limits(int node, struct meminfo *mi,
+	unsigned long *min, unsigned long *max_low, unsigned long *max_high)
+{
+	int i;
+
+	*min = -1UL;
+	*max_low = *max_high = 0;
+
+	for_each_nodebank(i, mi, node) {
+		struct membank *bank = &mi->bank[i];
+		unsigned long start, end;
+
+		start = bank_pfn_start(bank);
+		end = bank_pfn_end(bank);
+
+		if (*min > start)
+			*min = start;
+		if (*max_high < end)
+			*max_high = end;
+		if (bank->highmem)
+			continue;
+		if (*max_low < end)
+			*max_low = end;
+	}
+}
+
 /*
  * FIXME: We really want to avoid allocating the bootmap bitmap
  * over the top of the initrd.  Hopefully, this is located towards
@@ -210,40 +236,24 @@ static inline void map_memory_bank(struct membank *bank)
 #endif
 }
 
-static unsigned long __init bootmem_init_node(int node, struct meminfo *mi)
+static void __init bootmem_init_node(int node, struct meminfo *mi,
+	unsigned long start_pfn, unsigned long end_pfn)
 {
-	unsigned long start_pfn, end_pfn, boot_pfn;
+	unsigned long boot_pfn;
 	unsigned int boot_pages;
 	pg_data_t *pgdat;
 	int i;
 
-	start_pfn = -1UL;
-	end_pfn = 0;
-
 	/*
-	 * Calculate the pfn range, and map the memory banks for this node.
+	 * Map the memory banks for this node.
 	 */
 	for_each_nodebank(i, mi, node) {
 		struct membank *bank = &mi->bank[i];
-		unsigned long start, end;
 
-		start = bank_pfn_start(bank);
-		end = bank_pfn_end(bank);
-
-		if (start_pfn > start)
-			start_pfn = start;
-		if (end_pfn < end)
-			end_pfn = end;
-
-		map_memory_bank(bank);
+		if (!bank->highmem)
+			map_memory_bank(bank);
 	}
 
-	/*
-	 * If there is no memory in this node, ignore it.
-	 */
-	if (end_pfn == 0)
-		return end_pfn;
-
 	/*
 	 * Allocate the bootmem bitmap page.
 	 */
@@ -260,7 +270,8 @@ static unsigned long __init bootmem_init_node(int node, struct meminfo *mi)
 
 	for_each_nodebank(i, mi, node) {
 		struct membank *bank = &mi->bank[i];
-		free_bootmem_node(pgdat, bank_phys_start(bank), bank_phys_size(bank));
+		if (!bank->highmem)
+			free_bootmem_node(pgdat, bank_phys_start(bank), bank_phys_size(bank));
 		memory_present(node, bank_pfn_start(bank), bank_pfn_end(bank));
 	}
 
@@ -269,8 +280,6 @@ static unsigned long __init bootmem_init_node(int node, struct meminfo *mi)
 	 */
 	reserve_bootmem_node(pgdat, boot_pfn << PAGE_SHIFT,
 			     boot_pages << PAGE_SHIFT, BOOTMEM_DEFAULT);
-
-	return end_pfn;
 }
 
 static void __init bootmem_reserve_initrd(int node)
@@ -297,33 +306,39 @@ static void __init bootmem_reserve_initrd(int node)
 static void __init bootmem_free_node(int node, struct meminfo *mi)
 {
 	unsigned long zone_size[MAX_NR_ZONES], zhole_size[MAX_NR_ZONES];
-	unsigned long start_pfn, end_pfn;
-	pg_data_t *pgdat = NODE_DATA(node);
+	unsigned long min, max_low, max_high;
 	int i;
 
-	start_pfn = pgdat->bdata->node_min_pfn;
-	end_pfn = pgdat->bdata->node_low_pfn;
+	find_node_limits(node, mi, &min, &max_low, &max_high);
 
 	/*
 	 * initialise the zones within this node.
 	 */
 	memset(zone_size, 0, sizeof(zone_size));
-	memset(zhole_size, 0, sizeof(zhole_size));
 
 	/*
 	 * The size of this node has already been determined.  If we need
 	 * to do anything fancy with the allocation of this memory to the
 	 * zones, now is the time to do it.
 	 */
-	zone_size[0] = end_pfn - start_pfn;
+	zone_size[0] = max_low - min;
+#ifdef CONFIG_HIGHMEM
+	zone_size[ZONE_HIGHMEM] = max_high - max_low;
+#endif
 
 	/*
 	 * For each bank in this node, calculate the size of the holes.
 	 *  holes = node_size - sum(bank_sizes_in_node)
 	 */
-	zhole_size[0] = zone_size[0];
-	for_each_nodebank(i, mi, node)
-		zhole_size[0] -= bank_pfn_size(&mi->bank[i]);
+	memcpy(zhole_size, zone_size, sizeof(zhole_size));
+	for_each_nodebank(i, mi, node) {
+		int idx = 0;
+#ifdef CONFIG_HIGHMEM
+		if (mi->bank[i].highmem)
+			idx = ZONE_HIGHMEM;
+#endif
+		zhole_size[idx] -= bank_pfn_size(&mi->bank[i]);
+	}
 
 	/*
 	 * Adjust the sizes according to any special requirements for
@@ -331,13 +346,13 @@ static void __init bootmem_free_node(int node, struct meminfo *mi)
 	 */
 	arch_adjust_zones(node, zone_size, zhole_size);
 
-	free_area_init_node(node, zone_size, start_pfn, zhole_size);
+	free_area_init_node(node, zone_size, min, zhole_size);
 }
 
 void __init bootmem_init(void)
 {
 	struct meminfo *mi = &meminfo;
-	unsigned long memend_pfn = 0;
+	unsigned long min, max_low, max_high;
 	int node, initrd_node;
 
 	/*
@@ -345,11 +360,29 @@ void __init bootmem_init(void)
 	 */
 	initrd_node = check_initrd(mi);
 
+	max_low = max_high = 0;
+
 	/*
 	 * Run through each node initialising the bootmem allocator.
 	 */
 	for_each_node(node) {
-		unsigned long end_pfn = bootmem_init_node(node, mi);
+		unsigned long node_low, node_high;
+
+		find_node_limits(node, mi, &min, &node_low, &node_high);
+
+		if (node_low > max_low)
+			max_low = node_low;
+		if (node_high > max_high)
+			max_high = node_high;
+
+		/*
+		 * If there is no memory in this node, ignore it.
+		 * (We can't have nodes which have no lowmem)
+		 */
+		if (node_low == 0)
+			continue;
+
+		bootmem_init_node(node, mi, min, node_low);
 
 		/*
 		 * Reserve any special node zero regions.
@@ -362,12 +395,6 @@ void __init bootmem_init(void)
 		 */
 		if (node == initrd_node)
 			bootmem_reserve_initrd(node);
-
-		/*
-		 * Remember the highest memory PFN.
-		 */
-		if (end_pfn > memend_pfn)
-			memend_pfn = end_pfn;
 	}
 
 	/*
@@ -383,7 +410,7 @@ void __init bootmem_init(void)
 	for_each_node(node)
 		bootmem_free_node(node, mi);
 
-	high_memory = __va((memend_pfn << PAGE_SHIFT) - 1) + 1;
+	high_memory = __va((max_low << PAGE_SHIFT) - 1) + 1;
 
 	/*
 	 * This doesn't seem to be used by the Linux memory manager any
@@ -393,7 +420,8 @@ void __init bootmem_init(void)
 	 * Note: max_low_pfn and max_pfn reflect the number of _pages_ in
 	 * the system, not the maximum PFN.
 	 */
-	max_pfn = max_low_pfn = memend_pfn - PHYS_PFN_OFFSET;
+	max_low_pfn = max_low - PHYS_PFN_OFFSET;
+	max_pfn = max_high - PHYS_PFN_OFFSET;
 }
 
 static inline int free_area(unsigned long pfn, unsigned long end, char *s)
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 4722582b17b..4426ee67cec 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -687,13 +687,19 @@ __early_param("vmalloc=", early_vmalloc);
 
 static void __init sanity_check_meminfo(void)
 {
-	int i, j;
+	int i, j, highmem = 0;
 
 	for (i = 0, j = 0; i < meminfo.nr_banks; i++) {
 		struct membank *bank = &meminfo.bank[j];
 		*bank = meminfo.bank[i];
 
 #ifdef CONFIG_HIGHMEM
+		if (__va(bank->start) > VMALLOC_MIN ||
+		    __va(bank->start) < (void *)PAGE_OFFSET)
+			highmem = 1;
+
+		bank->highmem = highmem;
+
 		/*
 		 * Split those memory banks which are partially overlapping
 		 * the vmalloc area greatly simplifying things later.
@@ -714,6 +720,7 @@ static void __init sanity_check_meminfo(void)
 				i++;
 				bank[1].size -= VMALLOC_MIN - __va(bank->start);
 				bank[1].start = __pa(VMALLOC_MIN - 1) + 1;
+				bank[1].highmem = highmem = 1;
 				j++;
 			}
 			bank->size = VMALLOC_MIN - __va(bank->start);
-- 
GitLab


From c5e7f5a38a7ebf3697281bc7cb494e676f287ac0 Mon Sep 17 00:00:00 2001
From: Florian Fainelli <florian@openwrt.org>
Date: Wed, 3 Jun 2009 13:05:48 +0200
Subject: [PATCH 0896/1153] [WATCHDOG] ar7_wdt: fix path to ar7-specific
 headers

AR7 is currently being resubmitted for mainline inclusion
and we changed the path to the ar7-specific headers
from ar7 to mach-ar7 to reflect the other MIPS-based
boards header hierarchy. This patch will avoid any future
compilation failure due to missing headers.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
---
 drivers/watchdog/ar7_wdt.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/watchdog/ar7_wdt.c b/drivers/watchdog/ar7_wdt.c
index 3fe9742c23c..2f8643efe92 100644
--- a/drivers/watchdog/ar7_wdt.c
+++ b/drivers/watchdog/ar7_wdt.c
@@ -37,7 +37,7 @@
 #include <linux/uaccess.h>
 
 #include <asm/addrspace.h>
-#include <asm/ar7/ar7.h>
+#include <asm/mach-ar7/ar7.h>
 
 #define DRVNAME "ar7_wdt"
 #define LONGNAME "TI AR7 Watchdog Timer"
-- 
GitLab


From a2bb9f4d6a5a589b481595207ac3588cc08d1b60 Mon Sep 17 00:00:00 2001
From: Linus Walleij <linus.walleij@stericsson.com>
Date: Thu, 13 Aug 2009 21:57:22 +0100
Subject: [PATCH 0897/1153] ARM: 5673/1: U300 fix initsection compile warning

The u300_init_check_chip() function was not properly tagged with
the __init macro and provided a initsection mismatch on
compilation.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
---
 arch/arm/mach-u300/core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index 7936085dd75..2e9b8ccd8ec 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -510,7 +510,7 @@ static struct db_chip db_chips[] __initdata = {
 	}
 };
 
-static void u300_init_check_chip(void)
+static void __init u300_init_check_chip(void)
 {
 
 	u16 val;
-- 
GitLab


From 3f8befec95d5c1bbc6e247e1a5dafa82519530f9 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Sat, 15 Aug 2009 20:54:13 +1000
Subject: [PATCH 0898/1153] drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc
 for ZPASS_ADDR

These are needed for Occulsion Query support.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r300.c | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c
index 9c8d41534a5..8594486e162 100644
--- a/drivers/gpu/drm/radeon/r300.c
+++ b/drivers/gpu/drm/radeon/r300.c
@@ -1403,6 +1403,21 @@ static int r300_packet0_check(struct radeon_cs_parser *p,
 		tmp = (ib_chunk->kdata[idx] >> 22) & 0xF;
 		track->textures[i].txdepth = tmp;
 		break;
+	case R300_ZB_ZPASS_ADDR:
+		r = r100_cs_packet_next_reloc(p, &reloc);
+		if (r) {
+			DRM_ERROR("No reloc for ib[%d]=0x%04X\n",
+					idx, reg);
+			r100_cs_dump_packet(p, pkt);
+			return r;
+		}
+		ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+		break;
+	case 0x4be8:
+		/* valid register only on RV530 */
+		if (p->rdev->family == CHIP_RV530)
+			break;
+		/* fallthrough do not move */
 	default:
 		printk(KERN_ERR "Forbidden register 0x%04X in cs at %d\n",
 		       reg, idx);
-- 
GitLab


From 7ed220d738cf16adff6bc3b31ad25b8848a2fa9c Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Michel=20D=C3=A4nzer?= <daenzer@vmware.com>
Date: Thu, 13 Aug 2009 11:10:51 +0200
Subject: [PATCH 0899/1153] drm/radeon/kms: Fix up vertical blank interrupt
 support.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Fixes 3D apps timing out in the WAIT_VBLANK ioctl.

AVIVO bits compile-tested only.

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r100.c               | 66 +++++++++++++++++
 drivers/gpu/drm/radeon/r500_reg.h           | 16 +++-
 drivers/gpu/drm/radeon/radeon.h             |  2 +
 drivers/gpu/drm/radeon/radeon_asic.h        | 23 ++++--
 drivers/gpu/drm/radeon/radeon_irq_kms.c     | 54 --------------
 drivers/gpu/drm/radeon/radeon_kms.c         | 33 +++++++--
 drivers/gpu/drm/radeon/radeon_legacy_crtc.c |  7 +-
 drivers/gpu/drm/radeon/radeon_reg.h         | 11 ++-
 drivers/gpu/drm/radeon/rs600.c              | 82 +++++++++++++++++++++
 9 files changed, 217 insertions(+), 77 deletions(-)

diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index f1ba8ff4113..e1a6e82b996 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -253,6 +253,72 @@ void r100_mc_fini(struct radeon_device *rdev)
 }
 
 
+/*
+ * Interrupts
+ */
+int r100_irq_set(struct radeon_device *rdev)
+{
+	uint32_t tmp = 0;
+
+	if (rdev->irq.sw_int) {
+		tmp |= RADEON_SW_INT_ENABLE;
+	}
+	if (rdev->irq.crtc_vblank_int[0]) {
+		tmp |= RADEON_CRTC_VBLANK_MASK;
+	}
+	if (rdev->irq.crtc_vblank_int[1]) {
+		tmp |= RADEON_CRTC2_VBLANK_MASK;
+	}
+	WREG32(RADEON_GEN_INT_CNTL, tmp);
+	return 0;
+}
+
+static inline uint32_t r100_irq_ack(struct radeon_device *rdev)
+{
+	uint32_t irqs = RREG32(RADEON_GEN_INT_STATUS);
+	uint32_t irq_mask = RADEON_SW_INT_TEST | RADEON_CRTC_VBLANK_STAT |
+		RADEON_CRTC2_VBLANK_STAT;
+
+	if (irqs) {
+		WREG32(RADEON_GEN_INT_STATUS, irqs);
+	}
+	return irqs & irq_mask;
+}
+
+int r100_irq_process(struct radeon_device *rdev)
+{
+	uint32_t status;
+
+	status = r100_irq_ack(rdev);
+	if (!status) {
+		return IRQ_NONE;
+	}
+	while (status) {
+		/* SW interrupt */
+		if (status & RADEON_SW_INT_TEST) {
+			radeon_fence_process(rdev);
+		}
+		/* Vertical blank interrupts */
+		if (status & RADEON_CRTC_VBLANK_STAT) {
+			drm_handle_vblank(rdev->ddev, 0);
+		}
+		if (status & RADEON_CRTC2_VBLANK_STAT) {
+			drm_handle_vblank(rdev->ddev, 1);
+		}
+		status = r100_irq_ack(rdev);
+	}
+	return IRQ_HANDLED;
+}
+
+u32 r100_get_vblank_counter(struct radeon_device *rdev, int crtc)
+{
+	if (crtc == 0)
+		return RREG32(RADEON_CRTC_CRNT_FRAME);
+	else
+		return RREG32(RADEON_CRTC2_CRNT_FRAME);
+}
+
+
 /*
  * Fence emission
  */
diff --git a/drivers/gpu/drm/radeon/r500_reg.h b/drivers/gpu/drm/radeon/r500_reg.h
index 036691b38cb..e1d5e0331e1 100644
--- a/drivers/gpu/drm/radeon/r500_reg.h
+++ b/drivers/gpu/drm/radeon/r500_reg.h
@@ -350,6 +350,7 @@
 #define AVIVO_D1CRTC_BLANK_CONTROL                              0x6084
 #define AVIVO_D1CRTC_INTERLACE_CONTROL                          0x6088
 #define AVIVO_D1CRTC_INTERLACE_STATUS                           0x608c
+#define AVIVO_D1CRTC_FRAME_COUNT                                0x60a4
 #define AVIVO_D1CRTC_STEREO_CONTROL                             0x60c4
 
 /* master controls */
@@ -438,14 +439,15 @@
 #       define AVIVO_DC_LB_DISP1_END_ADR_SHIFT  4
 #       define AVIVO_DC_LB_DISP1_END_ADR_MASK   0x7ff
 
-#define R500_DxMODE_INT_MASK 0x6540
-#define R500_D1MODE_INT_MASK (1<<0)
-#define R500_D2MODE_INT_MASK (1<<8)
-
 #define AVIVO_D1MODE_DATA_FORMAT                0x6528
 #       define AVIVO_D1MODE_INTERLEAVE_EN       (1 << 0)
 #define AVIVO_D1MODE_DESKTOP_HEIGHT             0x652C
+#define AVIVO_D1MODE_VBLANK_STATUS              0x6534
+#       define AVIVO_VBLANK_ACK                 (1 << 4)
 #define AVIVO_D1MODE_VLINE_START_END            0x6538
+#define AVIVO_DxMODE_INT_MASK                   0x6540
+#       define AVIVO_D1MODE_INT_MASK            (1 << 0)
+#       define AVIVO_D2MODE_INT_MASK            (1 << 8)
 #define AVIVO_D1MODE_VIEWPORT_START             0x6580
 #define AVIVO_D1MODE_VIEWPORT_SIZE              0x6584
 #define AVIVO_D1MODE_EXT_OVERSCAN_LEFT_RIGHT    0x6588
@@ -475,6 +477,7 @@
 #define AVIVO_D2CRTC_BLANK_CONTROL                              0x6884
 #define AVIVO_D2CRTC_INTERLACE_CONTROL                          0x6888
 #define AVIVO_D2CRTC_INTERLACE_STATUS                           0x688c
+#define AVIVO_D2CRTC_FRAME_COUNT                                0x68a4
 #define AVIVO_D2CRTC_STEREO_CONTROL                             0x68c4
 
 #define AVIVO_D2GRPH_ENABLE                                     0x6900
@@ -497,6 +500,7 @@
 #define AVIVO_D2CUR_SIZE                        0x6c10
 #define AVIVO_D2CUR_POSITION                    0x6c14
 
+#define AVIVO_D2MODE_VBLANK_STATUS              0x6d34
 #define AVIVO_D2MODE_VLINE_START_END            0x6d38
 #define AVIVO_D2MODE_VIEWPORT_START             0x6d80
 #define AVIVO_D2MODE_VIEWPORT_SIZE              0x6d84
@@ -748,4 +752,8 @@
 #	define AVIVO_I2C_EN							(1 << 0)
 #	define AVIVO_I2C_RESET						(1 << 8)
 
+#define AVIVO_DISP_INTERRUPT_STATUS                             0x7edc
+#       define AVIVO_D1_VBLANK_INTERRUPT                        (1 << 4)
+#       define AVIVO_D2_VBLANK_INTERRUPT                        (1 << 5)
+
 #endif
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index b1d945b8ed6..34611274084 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -574,6 +574,7 @@ struct radeon_asic {
 	void (*ring_start)(struct radeon_device *rdev);
 	int (*irq_set)(struct radeon_device *rdev);
 	int (*irq_process)(struct radeon_device *rdev);
+	u32 (*get_vblank_counter)(struct radeon_device *rdev, int crtc);
 	void (*fence_ring_emit)(struct radeon_device *rdev, struct radeon_fence *fence);
 	int (*cs_parse)(struct radeon_cs_parser *p);
 	int (*copy_blit)(struct radeon_device *rdev,
@@ -862,6 +863,7 @@ static inline void radeon_ring_write(struct radeon_device *rdev, uint32_t v)
 #define radeon_ring_start(rdev) (rdev)->asic->ring_start((rdev))
 #define radeon_irq_set(rdev) (rdev)->asic->irq_set((rdev))
 #define radeon_irq_process(rdev) (rdev)->asic->irq_process((rdev))
+#define radeon_get_vblank_counter(rdev, crtc) (rdev)->asic->get_vblank_counter((rdev), (crtc))
 #define radeon_fence_ring_emit(rdev, fence) (rdev)->asic->fence_ring_emit((rdev), (fence))
 #define radeon_copy_blit(rdev, s, d, np, f) (rdev)->asic->copy_blit((rdev), (s), (d), (np), (f))
 #define radeon_copy_dma(rdev, s, d, np, f) (rdev)->asic->copy_dma((rdev), (s), (d), (np), (f))
diff --git a/drivers/gpu/drm/radeon/radeon_asic.h b/drivers/gpu/drm/radeon/radeon_asic.h
index c0ae2d92325..7ca6c13569b 100644
--- a/drivers/gpu/drm/radeon/radeon_asic.h
+++ b/drivers/gpu/drm/radeon/radeon_asic.h
@@ -49,6 +49,7 @@ void r100_vram_info(struct radeon_device *rdev);
 int r100_gpu_reset(struct radeon_device *rdev);
 int r100_mc_init(struct radeon_device *rdev);
 void r100_mc_fini(struct radeon_device *rdev);
+u32 r100_get_vblank_counter(struct radeon_device *rdev, int crtc);
 int r100_wb_init(struct radeon_device *rdev);
 void r100_wb_fini(struct radeon_device *rdev);
 int r100_gart_enable(struct radeon_device *rdev);
@@ -96,6 +97,7 @@ static struct radeon_asic r100_asic = {
 	.ring_start = &r100_ring_start,
 	.irq_set = &r100_irq_set,
 	.irq_process = &r100_irq_process,
+	.get_vblank_counter = &r100_get_vblank_counter,
 	.fence_ring_emit = &r100_fence_ring_emit,
 	.cs_parse = &r100_cs_parse,
 	.copy_blit = &r100_copy_blit,
@@ -156,6 +158,7 @@ static struct radeon_asic r300_asic = {
 	.ring_start = &r300_ring_start,
 	.irq_set = &r100_irq_set,
 	.irq_process = &r100_irq_process,
+	.get_vblank_counter = &r100_get_vblank_counter,
 	.fence_ring_emit = &r300_fence_ring_emit,
 	.cs_parse = &r300_cs_parse,
 	.copy_blit = &r100_copy_blit,
@@ -196,6 +199,7 @@ static struct radeon_asic r420_asic = {
 	.ring_start = &r300_ring_start,
 	.irq_set = &r100_irq_set,
 	.irq_process = &r100_irq_process,
+	.get_vblank_counter = &r100_get_vblank_counter,
 	.fence_ring_emit = &r300_fence_ring_emit,
 	.cs_parse = &r300_cs_parse,
 	.copy_blit = &r100_copy_blit,
@@ -243,6 +247,7 @@ static struct radeon_asic rs400_asic = {
 	.ring_start = &r300_ring_start,
 	.irq_set = &r100_irq_set,
 	.irq_process = &r100_irq_process,
+	.get_vblank_counter = &r100_get_vblank_counter,
 	.fence_ring_emit = &r300_fence_ring_emit,
 	.cs_parse = &r300_cs_parse,
 	.copy_blit = &r100_copy_blit,
@@ -266,6 +271,8 @@ void rs600_vram_info(struct radeon_device *rdev);
 int rs600_mc_init(struct radeon_device *rdev);
 void rs600_mc_fini(struct radeon_device *rdev);
 int rs600_irq_set(struct radeon_device *rdev);
+int rs600_irq_process(struct radeon_device *rdev);
+u32 rs600_get_vblank_counter(struct radeon_device *rdev, int crtc);
 int rs600_gart_enable(struct radeon_device *rdev);
 void rs600_gart_disable(struct radeon_device *rdev);
 void rs600_gart_tlb_flush(struct radeon_device *rdev);
@@ -291,7 +298,8 @@ static struct radeon_asic rs600_asic = {
 	.cp_disable = &r100_cp_disable,
 	.ring_start = &r300_ring_start,
 	.irq_set = &rs600_irq_set,
-	.irq_process = &r100_irq_process,
+	.irq_process = &rs600_irq_process,
+	.get_vblank_counter = &rs600_get_vblank_counter,
 	.fence_ring_emit = &r300_fence_ring_emit,
 	.cs_parse = &r300_cs_parse,
 	.copy_blit = &r100_copy_blit,
@@ -334,7 +342,8 @@ static struct radeon_asic rs690_asic = {
 	.cp_disable = &r100_cp_disable,
 	.ring_start = &r300_ring_start,
 	.irq_set = &rs600_irq_set,
-	.irq_process = &r100_irq_process,
+	.irq_process = &rs600_irq_process,
+	.get_vblank_counter = &rs600_get_vblank_counter,
 	.fence_ring_emit = &r300_fence_ring_emit,
 	.cs_parse = &r300_cs_parse,
 	.copy_blit = &r100_copy_blit,
@@ -382,8 +391,9 @@ static struct radeon_asic rv515_asic = {
 	.cp_fini = &r100_cp_fini,
 	.cp_disable = &r100_cp_disable,
 	.ring_start = &rv515_ring_start,
-	.irq_set = &r100_irq_set,
-	.irq_process = &r100_irq_process,
+	.irq_set = &rs600_irq_set,
+	.irq_process = &rs600_irq_process,
+	.get_vblank_counter = &rs600_get_vblank_counter,
 	.fence_ring_emit = &r300_fence_ring_emit,
 	.cs_parse = &r300_cs_parse,
 	.copy_blit = &r100_copy_blit,
@@ -424,8 +434,9 @@ static struct radeon_asic r520_asic = {
 	.cp_fini = &r100_cp_fini,
 	.cp_disable = &r100_cp_disable,
 	.ring_start = &rv515_ring_start,
-	.irq_set = &r100_irq_set,
-	.irq_process = &r100_irq_process,
+	.irq_set = &rs600_irq_set,
+	.irq_process = &rs600_irq_process,
+	.get_vblank_counter = &rs600_get_vblank_counter,
 	.fence_ring_emit = &r300_fence_ring_emit,
 	.cs_parse = &r300_cs_parse,
 	.copy_blit = &r100_copy_blit,
diff --git a/drivers/gpu/drm/radeon/radeon_irq_kms.c b/drivers/gpu/drm/radeon/radeon_irq_kms.c
index 491d569deb0..9805e4b6ca1 100644
--- a/drivers/gpu/drm/radeon/radeon_irq_kms.c
+++ b/drivers/gpu/drm/radeon/radeon_irq_kms.c
@@ -32,60 +32,6 @@
 #include "radeon.h"
 #include "atom.h"
 
-static inline uint32_t r100_irq_ack(struct radeon_device *rdev)
-{
-	uint32_t irqs = RREG32(RADEON_GEN_INT_STATUS);
-	uint32_t irq_mask = RADEON_SW_INT_TEST;
-
-	if (irqs) {
-		WREG32(RADEON_GEN_INT_STATUS, irqs);
-	}
-	return irqs & irq_mask;
-}
-
-int r100_irq_set(struct radeon_device *rdev)
-{
-	uint32_t tmp = 0;
-
-	if (rdev->irq.sw_int) {
-		tmp |= RADEON_SW_INT_ENABLE;
-	}
-	/* Todo go through CRTC and enable vblank int or not */
-	WREG32(RADEON_GEN_INT_CNTL, tmp);
-	return 0;
-}
-
-int r100_irq_process(struct radeon_device *rdev)
-{
-	uint32_t status;
-
-	status = r100_irq_ack(rdev);
-	if (!status) {
-		return IRQ_NONE;
-	}
-	while (status) {
-		/* SW interrupt */
-		if (status & RADEON_SW_INT_TEST) {
-			radeon_fence_process(rdev);
-		}
-		status = r100_irq_ack(rdev);
-	}
-	return IRQ_HANDLED;
-}
-
-int rs600_irq_set(struct radeon_device *rdev)
-{
-	uint32_t tmp = 0;
-
-	if (rdev->irq.sw_int) {
-		tmp |= RADEON_SW_INT_ENABLE;
-	}
-	WREG32(RADEON_GEN_INT_CNTL, tmp);
-	/* Todo go through CRTC and enable vblank int or not */
-	WREG32(R500_DxMODE_INT_MASK, 0);
-	return 0;
-}
-
 irqreturn_t radeon_driver_irq_handler_kms(DRM_IRQ_ARGS)
 {
 	struct drm_device *dev = (struct drm_device *) arg;
diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c
index 3357110e30c..d2764bf6b2a 100644
--- a/drivers/gpu/drm/radeon/radeon_kms.c
+++ b/drivers/gpu/drm/radeon/radeon_kms.c
@@ -141,19 +141,42 @@ void radeon_driver_preclose_kms(struct drm_device *dev,
  */
 u32 radeon_get_vblank_counter_kms(struct drm_device *dev, int crtc)
 {
-	/* FIXME: implement */
-	return 0;
+	struct radeon_device *rdev = dev->dev_private;
+
+	if (crtc < 0 || crtc > 1) {
+		DRM_ERROR("Invalid crtc %d\n", crtc);
+		return -EINVAL;
+	}
+
+	return radeon_get_vblank_counter(rdev, crtc);
 }
 
 int radeon_enable_vblank_kms(struct drm_device *dev, int crtc)
 {
-	/* FIXME: implement */
-	return 0;
+	struct radeon_device *rdev = dev->dev_private;
+
+	if (crtc < 0 || crtc > 1) {
+		DRM_ERROR("Invalid crtc %d\n", crtc);
+		return -EINVAL;
+	}
+
+	rdev->irq.crtc_vblank_int[crtc] = true;
+
+	return radeon_irq_set(rdev);
 }
 
 void radeon_disable_vblank_kms(struct drm_device *dev, int crtc)
 {
-	/* FIXME: implement */
+	struct radeon_device *rdev = dev->dev_private;
+
+	if (crtc < 0 || crtc > 1) {
+		DRM_ERROR("Invalid crtc %d\n", crtc);
+		return;
+	}
+
+	rdev->irq.crtc_vblank_int[crtc] = false;
+
+	radeon_irq_set(rdev);
 }
 
 
diff --git a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
index 7d06dc98a42..0da72f18fd3 100644
--- a/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
+++ b/drivers/gpu/drm/radeon/radeon_legacy_crtc.c
@@ -310,10 +310,13 @@ void radeon_crtc_dpms(struct drm_crtc *crtc, int mode)
 									 RADEON_CRTC_DISP_REQ_EN_B));
 			WREG32_P(RADEON_CRTC_EXT_CNTL, 0, ~mask);
 		}
+		drm_vblank_post_modeset(dev, radeon_crtc->crtc_id);
+		radeon_crtc_load_lut(crtc);
 		break;
 	case DRM_MODE_DPMS_STANDBY:
 	case DRM_MODE_DPMS_SUSPEND:
 	case DRM_MODE_DPMS_OFF:
+		drm_vblank_pre_modeset(dev, radeon_crtc->crtc_id);
 		if (radeon_crtc->crtc_id)
 			WREG32_P(RADEON_CRTC2_GEN_CNTL, mask, ~mask);
 		else {
@@ -323,10 +326,6 @@ void radeon_crtc_dpms(struct drm_crtc *crtc, int mode)
 		}
 		break;
 	}
-
-	if (mode != DRM_MODE_DPMS_OFF) {
-		radeon_crtc_load_lut(crtc);
-	}
 }
 
 /* properly set crtc bpp when using atombios */
diff --git a/drivers/gpu/drm/radeon/radeon_reg.h b/drivers/gpu/drm/radeon/radeon_reg.h
index e1b61857446..5a098f304ed 100644
--- a/drivers/gpu/drm/radeon/radeon_reg.h
+++ b/drivers/gpu/drm/radeon/radeon_reg.h
@@ -982,12 +982,15 @@
 #       define RS400_TMDS2_PLLRST           (1 << 1)
 
 #define RADEON_GEN_INT_CNTL                 0x0040
+#	define RADEON_CRTC_VBLANK_MASK		(1 << 0)
+#	define RADEON_CRTC2_VBLANK_MASK		(1 << 9)
 #	define RADEON_SW_INT_ENABLE		(1 << 25)
 #define RADEON_GEN_INT_STATUS               0x0044
-#       define RADEON_VSYNC_INT_AK          (1 <<  2)
-#       define RADEON_VSYNC_INT             (1 <<  2)
-#       define RADEON_VSYNC2_INT_AK         (1 <<  6)
-#       define RADEON_VSYNC2_INT            (1 <<  6)
+#	define AVIVO_DISPLAY_INT_STATUS		(1 << 0)
+#	define RADEON_CRTC_VBLANK_STAT		(1 << 0)
+#	define RADEON_CRTC_VBLANK_STAT_ACK	(1 << 0)
+#	define RADEON_CRTC2_VBLANK_STAT		(1 << 9)
+#	define RADEON_CRTC2_VBLANK_STAT_ACK	(1 << 9)
 #	define RADEON_SW_INT_FIRE		(1 << 26)
 #	define RADEON_SW_INT_TEST		(1 << 25)
 #	define RADEON_SW_INT_TEST_ACK		(1 << 25)
diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c
index bbea6dee4a9..7e8ce983a90 100644
--- a/drivers/gpu/drm/radeon/rs600.c
+++ b/drivers/gpu/drm/radeon/rs600.c
@@ -239,6 +239,88 @@ void rs600_mc_fini(struct radeon_device *rdev)
 }
 
 
+/*
+ * Interrupts
+ */
+int rs600_irq_set(struct radeon_device *rdev)
+{
+	uint32_t tmp = 0;
+	uint32_t mode_int = 0;
+
+	if (rdev->irq.sw_int) {
+		tmp |= RADEON_SW_INT_ENABLE;
+	}
+	if (rdev->irq.crtc_vblank_int[0]) {
+		tmp |= AVIVO_DISPLAY_INT_STATUS;
+		mode_int |= AVIVO_D1MODE_INT_MASK;
+	}
+	if (rdev->irq.crtc_vblank_int[1]) {
+		tmp |= AVIVO_DISPLAY_INT_STATUS;
+		mode_int |= AVIVO_D2MODE_INT_MASK;
+	}
+	WREG32(RADEON_GEN_INT_CNTL, tmp);
+	WREG32(AVIVO_DxMODE_INT_MASK, mode_int);
+	return 0;
+}
+
+static inline uint32_t rs600_irq_ack(struct radeon_device *rdev, u32 *r500_disp_int)
+{
+	uint32_t irqs = RREG32(RADEON_GEN_INT_STATUS);
+	uint32_t irq_mask = RADEON_SW_INT_TEST;
+
+	if (irqs & AVIVO_DISPLAY_INT_STATUS) {
+		*r500_disp_int = RREG32(AVIVO_DISP_INTERRUPT_STATUS);
+		if (*r500_disp_int & AVIVO_D1_VBLANK_INTERRUPT) {
+			WREG32(AVIVO_D1MODE_VBLANK_STATUS, AVIVO_VBLANK_ACK);
+		}
+		if (*r500_disp_int & AVIVO_D2_VBLANK_INTERRUPT) {
+			WREG32(AVIVO_D2MODE_VBLANK_STATUS, AVIVO_VBLANK_ACK);
+		}
+	} else {
+		*r500_disp_int = 0;
+	}
+
+	if (irqs) {
+		WREG32(RADEON_GEN_INT_STATUS, irqs);
+	}
+	return irqs & irq_mask;
+}
+
+int rs600_irq_process(struct radeon_device *rdev)
+{
+	uint32_t status;
+	uint32_t r500_disp_int;
+
+	status = rs600_irq_ack(rdev, &r500_disp_int);
+	if (!status && !r500_disp_int) {
+		return IRQ_NONE;
+	}
+	while (status || r500_disp_int) {
+		/* SW interrupt */
+		if (status & RADEON_SW_INT_TEST) {
+			radeon_fence_process(rdev);
+		}
+		/* Vertical blank interrupts */
+		if (r500_disp_int & AVIVO_D1_VBLANK_INTERRUPT) {
+			drm_handle_vblank(rdev->ddev, 0);
+		}
+		if (r500_disp_int & AVIVO_D2_VBLANK_INTERRUPT) {
+			drm_handle_vblank(rdev->ddev, 1);
+		}
+		status = rs600_irq_ack(rdev, &r500_disp_int);
+	}
+	return IRQ_HANDLED;
+}
+
+u32 rs600_get_vblank_counter(struct radeon_device *rdev, int crtc)
+{
+	if (crtc == 0)
+		return RREG32(AVIVO_D1CRTC_FRAME_COUNT);
+	else
+		return RREG32(AVIVO_D2CRTC_FRAME_COUNT);
+}
+
+
 /*
  * Global GPU functions
  */
-- 
GitLab


From de1b28989edff519d0548ebaa3f94fd3d1524cf2 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Wed, 12 Aug 2009 18:43:14 +1000
Subject: [PATCH 0900/1153] drm/radeon/kms: cut down indirects in register
 accesses.

We really don't want to be doing all these indirects, updating
the GPU gart table is something we do often so the less overhead the
better.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r100.c          | 20 ----------
 drivers/gpu/drm/radeon/r300.c          | 23 +-----------
 drivers/gpu/drm/radeon/radeon.h        | 51 ++++++++++++++++++++++----
 drivers/gpu/drm/radeon/radeon_device.c | 13 ++-----
 drivers/gpu/drm/radeon/rv515.c         | 19 ----------
 5 files changed, 47 insertions(+), 79 deletions(-)

diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index e1a6e82b996..90ff8e0ac04 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -1622,26 +1622,6 @@ void r100_pll_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
 	r100_pll_errata_after_data(rdev);
 }
 
-uint32_t r100_mm_rreg(struct radeon_device *rdev, uint32_t reg)
-{
-	if (reg < 0x10000)
-		return readl(((void __iomem *)rdev->rmmio) + reg);
-	else {
-		writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX);
-		return readl(((void __iomem *)rdev->rmmio) + RADEON_MM_DATA);
-	}
-}
-
-void r100_mm_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
-{
-	if (reg < 0x10000)
-		writel(v, ((void __iomem *)rdev->rmmio) + reg);
-	else {
-		writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX);
-		writel(v, ((void __iomem *)rdev->rmmio) + RADEON_MM_DATA);
-	}
-}
-
 int r100_init(struct radeon_device *rdev)
 {
 	return 0;
diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c
index 8594486e162..c47579dcafa 100644
--- a/drivers/gpu/drm/radeon/r300.c
+++ b/drivers/gpu/drm/radeon/r300.c
@@ -83,8 +83,8 @@ void rv370_pcie_gart_tlb_flush(struct radeon_device *rdev)
 		WREG32_PCIE(RADEON_PCIE_TX_GART_CNTL, tmp | RADEON_PCIE_TX_GART_INVALIDATE_TLB);
 		(void)RREG32_PCIE(RADEON_PCIE_TX_GART_CNTL);
 		WREG32_PCIE(RADEON_PCIE_TX_GART_CNTL, tmp);
-		mb();
 	}
+	mb();
 }
 
 int rv370_pcie_gart_enable(struct radeon_device *rdev)
@@ -592,27 +592,6 @@ void r300_vram_info(struct radeon_device *rdev)
 }
 
 
-/*
- * Indirect registers accessor
- */
-uint32_t rv370_pcie_rreg(struct radeon_device *rdev, uint32_t reg)
-{
-	uint32_t r;
-
-	WREG8(RADEON_PCIE_INDEX, ((reg) & 0xff));
-	(void)RREG32(RADEON_PCIE_INDEX);
-	r = RREG32(RADEON_PCIE_DATA);
-	return r;
-}
-
-void rv370_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
-{
-	WREG8(RADEON_PCIE_INDEX, ((reg) & 0xff));
-	(void)RREG32(RADEON_PCIE_INDEX);
-	WREG32(RADEON_PCIE_DATA, (v));
-	(void)RREG32(RADEON_PCIE_DATA);
-}
-
 /*
  * PCIE Lanes
  */
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index 34611274084..87170a56e37 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -667,14 +667,11 @@ struct radeon_device {
 	resource_size_t			rmmio_base;
 	resource_size_t			rmmio_size;
 	void				*rmmio;
-	radeon_rreg_t			mm_rreg;
-	radeon_wreg_t			mm_wreg;
 	radeon_rreg_t			mc_rreg;
 	radeon_wreg_t			mc_wreg;
 	radeon_rreg_t			pll_rreg;
 	radeon_wreg_t			pll_wreg;
-	radeon_rreg_t			pcie_rreg;
-	radeon_wreg_t			pcie_wreg;
+	uint32_t                        pcie_reg_mask;
 	radeon_rreg_t			pciep_rreg;
 	radeon_wreg_t			pciep_wreg;
 	struct radeon_clock             clock;
@@ -706,22 +703,42 @@ int radeon_device_init(struct radeon_device *rdev,
 void radeon_device_fini(struct radeon_device *rdev);
 int radeon_gpu_wait_for_idle(struct radeon_device *rdev);
 
+static inline uint32_t r100_mm_rreg(struct radeon_device *rdev, uint32_t reg)
+{
+	if (reg < 0x10000)
+		return readl(((void __iomem *)rdev->rmmio) + reg);
+	else {
+		writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX);
+		return readl(((void __iomem *)rdev->rmmio) + RADEON_MM_DATA);
+	}
+}
+
+static inline void r100_mm_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
+{
+	if (reg < 0x10000)
+		writel(v, ((void __iomem *)rdev->rmmio) + reg);
+	else {
+		writel(reg, ((void __iomem *)rdev->rmmio) + RADEON_MM_INDEX);
+		writel(v, ((void __iomem *)rdev->rmmio) + RADEON_MM_DATA);
+	}
+}
+
 
 /*
  * Registers read & write functions.
  */
 #define RREG8(reg) readb(((void __iomem *)rdev->rmmio) + (reg))
 #define WREG8(reg, v) writeb(v, ((void __iomem *)rdev->rmmio) + (reg))
-#define RREG32(reg) rdev->mm_rreg(rdev, (reg))
-#define WREG32(reg, v) rdev->mm_wreg(rdev, (reg), (v))
+#define RREG32(reg) r100_mm_rreg(rdev, (reg))
+#define WREG32(reg, v) r100_mm_wreg(rdev, (reg), (v))
 #define REG_SET(FIELD, v) (((v) << FIELD##_SHIFT) & FIELD##_MASK)
 #define REG_GET(FIELD, v) (((v) << FIELD##_SHIFT) & FIELD##_MASK)
 #define RREG32_PLL(reg) rdev->pll_rreg(rdev, (reg))
 #define WREG32_PLL(reg, v) rdev->pll_wreg(rdev, (reg), (v))
 #define RREG32_MC(reg) rdev->mc_rreg(rdev, (reg))
 #define WREG32_MC(reg, v) rdev->mc_wreg(rdev, (reg), (v))
-#define RREG32_PCIE(reg) rdev->pcie_rreg(rdev, (reg))
-#define WREG32_PCIE(reg, v) rdev->pcie_wreg(rdev, (reg), (v))
+#define RREG32_PCIE(reg) rv370_pcie_rreg(rdev, (reg))
+#define WREG32_PCIE(reg, v) rv370_pcie_wreg(rdev, (reg), (v))
 #define WREG32_P(reg, val, mask)				\
 	do {							\
 		uint32_t tmp_ = RREG32(reg);			\
@@ -737,6 +754,24 @@ int radeon_gpu_wait_for_idle(struct radeon_device *rdev);
 		WREG32_PLL(reg, tmp_);				\
 	} while (0)
 
+/*
+ * Indirect registers accessor
+ */
+static inline uint32_t rv370_pcie_rreg(struct radeon_device *rdev, uint32_t reg)
+{
+	uint32_t r;
+
+	WREG32(RADEON_PCIE_INDEX, ((reg) & rdev->pcie_reg_mask));
+	r = RREG32(RADEON_PCIE_DATA);
+	return r;
+}
+
+static inline void rv370_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
+{
+	WREG32(RADEON_PCIE_INDEX, ((reg) & rdev->pcie_reg_mask));
+	WREG32(RADEON_PCIE_DATA, (v));
+}
+
 void r100_pll_errata_after_index(struct radeon_device *rdev);
 
 
diff --git a/drivers/gpu/drm/radeon/radeon_device.c b/drivers/gpu/drm/radeon/radeon_device.c
index 9ff6dcb97f9..7693f7c67bd 100644
--- a/drivers/gpu/drm/radeon/radeon_device.c
+++ b/drivers/gpu/drm/radeon/radeon_device.c
@@ -225,25 +225,18 @@ void radeon_invalid_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
 
 void radeon_register_accessor_init(struct radeon_device *rdev)
 {
-	rdev->mm_rreg = &r100_mm_rreg;
-	rdev->mm_wreg = &r100_mm_wreg;
 	rdev->mc_rreg = &radeon_invalid_rreg;
 	rdev->mc_wreg = &radeon_invalid_wreg;
 	rdev->pll_rreg = &radeon_invalid_rreg;
 	rdev->pll_wreg = &radeon_invalid_wreg;
-	rdev->pcie_rreg = &radeon_invalid_rreg;
-	rdev->pcie_wreg = &radeon_invalid_wreg;
 	rdev->pciep_rreg = &radeon_invalid_rreg;
 	rdev->pciep_wreg = &radeon_invalid_wreg;
 
 	/* Don't change order as we are overridding accessor. */
 	if (rdev->family < CHIP_RV515) {
-		rdev->pcie_rreg = &rv370_pcie_rreg;
-		rdev->pcie_wreg = &rv370_pcie_wreg;
-	}
-	if (rdev->family >= CHIP_RV515) {
-		rdev->pcie_rreg = &rv515_pcie_rreg;
-		rdev->pcie_wreg = &rv515_pcie_wreg;
+		rdev->pcie_reg_mask = 0xff;
+	} else {
+		rdev->pcie_reg_mask = 0x7ff;
 	}
 	/* FIXME: not sure here */
 	if (rdev->family <= CHIP_R580) {
diff --git a/drivers/gpu/drm/radeon/rv515.c b/drivers/gpu/drm/radeon/rv515.c
index fd8f3ca716e..31a7f668ae5 100644
--- a/drivers/gpu/drm/radeon/rv515.c
+++ b/drivers/gpu/drm/radeon/rv515.c
@@ -400,25 +400,6 @@ void rv515_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
 	WREG32(MC_IND_INDEX, 0);
 }
 
-uint32_t rv515_pcie_rreg(struct radeon_device *rdev, uint32_t reg)
-{
-	uint32_t r;
-
-	WREG32(PCIE_INDEX, ((reg) & 0x7ff));
-	(void)RREG32(PCIE_INDEX);
-	r = RREG32(PCIE_DATA);
-	return r;
-}
-
-void rv515_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v)
-{
-	WREG32(PCIE_INDEX, ((reg) & 0x7ff));
-	(void)RREG32(PCIE_INDEX);
-	WREG32(PCIE_DATA, (v));
-	(void)RREG32(PCIE_DATA);
-}
-
-
 /*
  * Debugfs info
  */
-- 
GitLab


From b2add73dbf93fd50f00564d7abc3e2b9aa9dd20c Mon Sep 17 00:00:00 2001
From: Guillaume Knispel <gknispel@proformatique.com>
Date: Sat, 15 Aug 2009 19:30:24 +0200
Subject: [PATCH 0901/1153] poll/select: initialize triggered field of struct
 poll_wqueues

The triggered field of struct poll_wqueues introduced in commit
5f820f648c92a5ecc771a96b3c29aa6e90013bba ("poll: allow f_op->poll to
sleep").

It was first set to 1 in pollwake() (now __pollwake() ), tested and
later set to 0 in poll_schedule_timeout(), but not initialized before.

As a result when the process needs to sleep, triggered was likely to be
non-zero even if pollwake() is not called before the first
poll_schedule_timeout(), meaning schedule_hrtimeout_range() would not be
called and an extra loop calling all ->poll() would be done.

This patch initialize triggered to 0 in poll_initwait() so the ->poll()
are not called twice before the process goes to sleep when it needs to.

Signed-off-by: Guillaume Knispel <gknispel@proformatique.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/select.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/fs/select.c b/fs/select.c
index d870237e42c..8084834e123 100644
--- a/fs/select.c
+++ b/fs/select.c
@@ -110,6 +110,7 @@ void poll_initwait(struct poll_wqueues *pwq)
 {
 	init_poll_funcptr(&pwq->pt, __pollwait);
 	pwq->polling_task = current;
+	pwq->triggered = 0;
 	pwq->error = 0;
 	pwq->table = NULL;
 	pwq->inline_index = 0;
-- 
GitLab


From 64c6460875957502541a4ba30835ac625a0bee79 Mon Sep 17 00:00:00 2001
From: Michael Chan <mchan@broadcom.com>
Date: Fri, 14 Aug 2009 15:49:43 +0000
Subject: [PATCH 0902/1153] cnic: Fix symbol_put_addr() panic on ia64.

When the cnic driver tries to grab a symbol from bnx2 when bnx2 is
running init code, symbol_get() will succeed but symbol_put_addr()
will hit BUG() a moment later.  module_text_address() fails because
bnx2 is still in init code.

This is fixed by using symbol_put() instead which does the exact
opposite of symbol_get().

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/cnic.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c
index 4869d77cbe9..ecde186fccd 100644
--- a/drivers/net/cnic.c
+++ b/drivers/net/cnic.c
@@ -2543,7 +2543,7 @@ static struct cnic_dev *init_bnx2_cnic(struct net_device *dev)
 	probe = symbol_get(bnx2_cnic_probe);
 	if (probe) {
 		ethdev = (*probe)(dev);
-		symbol_put_addr(probe);
+		symbol_put(bnx2_cnic_probe);
 	}
 	if (!ethdev)
 		return NULL;
-- 
GitLab


From a3059b12adae868c42629ecf058a94195ef1e958 Mon Sep 17 00:00:00 2001
From: Michael Chan <mchan@broadcom.com>
Date: Fri, 14 Aug 2009 15:49:44 +0000
Subject: [PATCH 0903/1153] cnic: Refine registration with bnx2.

Register and unregister with bnx2 during NETDEV_UP and NETDEV_DOWN
events.  This simplifies the sequence of events and allows locking
fixes in the next patch.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/cnic.c | 49 ++++++++++++++++++++++++++++++++++------------
 1 file changed, 36 insertions(+), 13 deletions(-)

diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c
index ecde186fccd..2db81f0e4f7 100644
--- a/drivers/net/cnic.c
+++ b/drivers/net/cnic.c
@@ -2393,21 +2393,45 @@ static int cnic_start_bnx2_hw(struct cnic_dev *dev)
 	return 0;
 }
 
-static int cnic_start_hw(struct cnic_dev *dev)
+static int cnic_register_netdev(struct cnic_dev *dev)
 {
 	struct cnic_local *cp = dev->cnic_priv;
 	struct cnic_eth_dev *ethdev = cp->ethdev;
 	int err;
 
-	if (test_bit(CNIC_F_CNIC_UP, &dev->flags))
-		return -EALREADY;
+	if (!ethdev)
+		return -ENODEV;
+
+	if (ethdev->drv_state & CNIC_DRV_STATE_REGD)
+		return 0;
 
 	err = ethdev->drv_register_cnic(dev->netdev, cp->cnic_ops, dev);
-	if (err) {
+	if (err)
 		printk(KERN_ERR PFX "%s: register_cnic failed\n",
 		       dev->netdev->name);
-		goto err2;
-	}
+
+	return err;
+}
+
+static void cnic_unregister_netdev(struct cnic_dev *dev)
+{
+	struct cnic_local *cp = dev->cnic_priv;
+	struct cnic_eth_dev *ethdev = cp->ethdev;
+
+	if (!ethdev)
+		return;
+
+	ethdev->drv_unregister_cnic(dev->netdev);
+}
+
+static int cnic_start_hw(struct cnic_dev *dev)
+{
+	struct cnic_local *cp = dev->cnic_priv;
+	struct cnic_eth_dev *ethdev = cp->ethdev;
+	int err;
+
+	if (test_bit(CNIC_F_CNIC_UP, &dev->flags))
+		return -EALREADY;
 
 	dev->regview = ethdev->io_base;
 	cp->chip_id = ethdev->chip_id;
@@ -2438,18 +2462,13 @@ static int cnic_start_hw(struct cnic_dev *dev)
 	return 0;
 
 err1:
-	ethdev->drv_unregister_cnic(dev->netdev);
 	cp->free_resc(dev);
 	pci_dev_put(dev->pcidev);
-err2:
 	return err;
 }
 
 static void cnic_stop_bnx2_hw(struct cnic_dev *dev)
 {
-	struct cnic_local *cp = dev->cnic_priv;
-	struct cnic_eth_dev *ethdev = cp->ethdev;
-
 	cnic_disable_bnx2_int_sync(dev);
 
 	cnic_reg_wr_ind(dev, BNX2_CP_SCRATCH + 0x20, 0);
@@ -2461,8 +2480,6 @@ static void cnic_stop_bnx2_hw(struct cnic_dev *dev)
 	cnic_setup_5709_context(dev, 0);
 	cnic_free_irq(dev);
 
-	ethdev->drv_unregister_cnic(dev->netdev);
-
 	cnic_free_resc(dev);
 }
 
@@ -2646,6 +2663,10 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event,
 		else if (event == NETDEV_UNREGISTER)
 			cnic_ulp_exit(dev);
 		else if (event == NETDEV_UP) {
+			if (cnic_register_netdev(dev) != 0) {
+				cnic_put(dev);
+				goto done;
+			}
 			mutex_lock(&cnic_lock);
 			if (!cnic_start_hw(dev))
 				cnic_ulp_start(dev);
@@ -2672,6 +2693,7 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event,
 			cnic_ulp_stop(dev);
 			cnic_stop_hw(dev);
 			mutex_unlock(&cnic_lock);
+			cnic_unregister_netdev(dev);
 		} else if (event == NETDEV_UNREGISTER) {
 			write_lock(&cnic_dev_lock);
 			list_del_init(&dev->list);
@@ -2703,6 +2725,7 @@ static void cnic_release(void)
 		}
 
 		cnic_ulp_exit(dev);
+		cnic_unregister_netdev(dev);
 		list_del_init(&dev->list);
 		cnic_free_dev(dev);
 	}
-- 
GitLab


From c5a889508203446c1abc1d670599b3a816841813 Mon Sep 17 00:00:00 2001
From: Michael Chan <mchan@broadcom.com>
Date: Fri, 14 Aug 2009 15:49:45 +0000
Subject: [PATCH 0904/1153] bnx2: Use mutex on slow path cnic calls.

The slow path calls to the cnic driver are sleepable calls so we
cannot use rcu_read_lock().  Use mutex for these slow path calls
instead.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/bnx2.c | 17 +++++++++++------
 drivers/net/bnx2.h |  1 +
 2 files changed, 12 insertions(+), 6 deletions(-)

diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c
index b70cc99962f..06b901152d4 100644
--- a/drivers/net/bnx2.c
+++ b/drivers/net/bnx2.c
@@ -399,9 +399,11 @@ static int bnx2_unregister_cnic(struct net_device *dev)
 	struct bnx2_napi *bnapi = &bp->bnx2_napi[0];
 	struct cnic_eth_dev *cp = &bp->cnic_eth_dev;
 
+	mutex_lock(&bp->cnic_lock);
 	cp->drv_state = 0;
 	bnapi->cnic_present = 0;
 	rcu_assign_pointer(bp->cnic_ops, NULL);
+	mutex_unlock(&bp->cnic_lock);
 	synchronize_rcu();
 	return 0;
 }
@@ -429,13 +431,13 @@ bnx2_cnic_stop(struct bnx2 *bp)
 	struct cnic_ops *c_ops;
 	struct cnic_ctl_info info;
 
-	rcu_read_lock();
-	c_ops = rcu_dereference(bp->cnic_ops);
+	mutex_lock(&bp->cnic_lock);
+	c_ops = bp->cnic_ops;
 	if (c_ops) {
 		info.cmd = CNIC_CTL_STOP_CMD;
 		c_ops->cnic_ctl(bp->cnic_data, &info);
 	}
-	rcu_read_unlock();
+	mutex_unlock(&bp->cnic_lock);
 }
 
 static void
@@ -444,8 +446,8 @@ bnx2_cnic_start(struct bnx2 *bp)
 	struct cnic_ops *c_ops;
 	struct cnic_ctl_info info;
 
-	rcu_read_lock();
-	c_ops = rcu_dereference(bp->cnic_ops);
+	mutex_lock(&bp->cnic_lock);
+	c_ops = bp->cnic_ops;
 	if (c_ops) {
 		if (!(bp->flags & BNX2_FLAG_USING_MSIX)) {
 			struct bnx2_napi *bnapi = &bp->bnx2_napi[0];
@@ -455,7 +457,7 @@ bnx2_cnic_start(struct bnx2 *bp)
 		info.cmd = CNIC_CTL_START_CMD;
 		c_ops->cnic_ctl(bp->cnic_data, &info);
 	}
-	rcu_read_unlock();
+	mutex_unlock(&bp->cnic_lock);
 }
 
 #else
@@ -7663,6 +7665,9 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev)
 
 	spin_lock_init(&bp->phy_lock);
 	spin_lock_init(&bp->indirect_lock);
+#ifdef BCM_CNIC
+	mutex_init(&bp->cnic_lock);
+#endif
 	INIT_WORK(&bp->reset_task, bnx2_reset_task);
 
 	dev->base_addr = dev->mem_start = pci_resource_start(pdev, 0);
diff --git a/drivers/net/bnx2.h b/drivers/net/bnx2.h
index f1edfaa9e56..a4f12fd0ecd 100644
--- a/drivers/net/bnx2.h
+++ b/drivers/net/bnx2.h
@@ -6902,6 +6902,7 @@ struct bnx2 {
 	u32			idle_chk_status_idx;
 
 #ifdef BCM_CNIC
+	struct mutex		cnic_lock;
 	struct cnic_eth_dev	cnic_eth_dev;
 #endif
 
-- 
GitLab


From 681dbd710779e8b8d5bae926f6b11f30df70638b Mon Sep 17 00:00:00 2001
From: Michael Chan <mchan@broadcom.com>
Date: Fri, 14 Aug 2009 15:49:46 +0000
Subject: [PATCH 0905/1153] cnic: Fix locking in start/stop calls.

The slow path ulp_start and ulp_stop calls to the bnx2i driver
are sleepable calls and therefore should not be protected using
rcu_read_lock.  Fix it by using mutex and setting a bit during
these calls.  cnic_unregister_device() will now wait for the bit
to clear before completing the call.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/cnic.c | 44 ++++++++++++++++++++++++++++----------------
 drivers/net/cnic.h |  1 +
 2 files changed, 29 insertions(+), 16 deletions(-)

diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c
index 2db81f0e4f7..4ff618a7afd 100644
--- a/drivers/net/cnic.c
+++ b/drivers/net/cnic.c
@@ -466,6 +466,7 @@ EXPORT_SYMBOL(cnic_register_driver);
 static int cnic_unregister_device(struct cnic_dev *dev, int ulp_type)
 {
 	struct cnic_local *cp = dev->cnic_priv;
+	int i = 0;
 
 	if (ulp_type >= MAX_CNIC_ULP_TYPE) {
 		printk(KERN_ERR PFX "cnic_unregister_device: Bad type %d\n",
@@ -486,6 +487,15 @@ static int cnic_unregister_device(struct cnic_dev *dev, int ulp_type)
 
 	synchronize_rcu();
 
+	while (test_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[ulp_type]) &&
+	       i < 20) {
+		msleep(100);
+		i++;
+	}
+	if (test_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[ulp_type]))
+		printk(KERN_WARNING PFX "%s: Failed waiting for ULP up call"
+					" to complete.\n", dev->netdev->name);
+
 	return 0;
 }
 EXPORT_SYMBOL(cnic_unregister_driver);
@@ -1076,18 +1086,23 @@ static void cnic_ulp_stop(struct cnic_dev *dev)
 	if (cp->cnic_uinfo)
 		cnic_send_nlmsg(cp, ISCSI_KEVENT_IF_DOWN, NULL);
 
-	rcu_read_lock();
 	for (if_type = 0; if_type < MAX_CNIC_ULP_TYPE; if_type++) {
 		struct cnic_ulp_ops *ulp_ops;
 
-		ulp_ops = rcu_dereference(cp->ulp_ops[if_type]);
-		if (!ulp_ops)
+		mutex_lock(&cnic_lock);
+		ulp_ops = cp->ulp_ops[if_type];
+		if (!ulp_ops) {
+			mutex_unlock(&cnic_lock);
 			continue;
+		}
+		set_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]);
+		mutex_unlock(&cnic_lock);
 
 		if (test_and_clear_bit(ULP_F_START, &cp->ulp_flags[if_type]))
 			ulp_ops->cnic_stop(cp->ulp_handle[if_type]);
+
+		clear_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]);
 	}
-	rcu_read_unlock();
 }
 
 static void cnic_ulp_start(struct cnic_dev *dev)
@@ -1095,18 +1110,23 @@ static void cnic_ulp_start(struct cnic_dev *dev)
 	struct cnic_local *cp = dev->cnic_priv;
 	int if_type;
 
-	rcu_read_lock();
 	for (if_type = 0; if_type < MAX_CNIC_ULP_TYPE; if_type++) {
 		struct cnic_ulp_ops *ulp_ops;
 
-		ulp_ops = rcu_dereference(cp->ulp_ops[if_type]);
-		if (!ulp_ops || !ulp_ops->cnic_start)
+		mutex_lock(&cnic_lock);
+		ulp_ops = cp->ulp_ops[if_type];
+		if (!ulp_ops || !ulp_ops->cnic_start) {
+			mutex_unlock(&cnic_lock);
 			continue;
+		}
+		set_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]);
+		mutex_unlock(&cnic_lock);
 
 		if (!test_and_set_bit(ULP_F_START, &cp->ulp_flags[if_type]))
 			ulp_ops->cnic_start(cp->ulp_handle[if_type]);
+
+		clear_bit(ULP_F_CALL_PENDING, &cp->ulp_flags[if_type]);
 	}
-	rcu_read_unlock();
 }
 
 static int cnic_ctl(void *data, struct cnic_ctl_info *info)
@@ -1116,22 +1136,18 @@ static int cnic_ctl(void *data, struct cnic_ctl_info *info)
 	switch (info->cmd) {
 	case CNIC_CTL_STOP_CMD:
 		cnic_hold(dev);
-		mutex_lock(&cnic_lock);
 
 		cnic_ulp_stop(dev);
 		cnic_stop_hw(dev);
 
-		mutex_unlock(&cnic_lock);
 		cnic_put(dev);
 		break;
 	case CNIC_CTL_START_CMD:
 		cnic_hold(dev);
-		mutex_lock(&cnic_lock);
 
 		if (!cnic_start_hw(dev))
 			cnic_ulp_start(dev);
 
-		mutex_unlock(&cnic_lock);
 		cnic_put(dev);
 		break;
 	default:
@@ -2667,10 +2683,8 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event,
 				cnic_put(dev);
 				goto done;
 			}
-			mutex_lock(&cnic_lock);
 			if (!cnic_start_hw(dev))
 				cnic_ulp_start(dev);
-			mutex_unlock(&cnic_lock);
 		}
 
 		rcu_read_lock();
@@ -2689,10 +2703,8 @@ static int cnic_netdev_event(struct notifier_block *this, unsigned long event,
 		rcu_read_unlock();
 
 		if (event == NETDEV_GOING_DOWN) {
-			mutex_lock(&cnic_lock);
 			cnic_ulp_stop(dev);
 			cnic_stop_hw(dev);
-			mutex_unlock(&cnic_lock);
 			cnic_unregister_netdev(dev);
 		} else if (event == NETDEV_UNREGISTER) {
 			write_lock(&cnic_dev_lock);
diff --git a/drivers/net/cnic.h b/drivers/net/cnic.h
index 5192d4a9df5..a94b302bb46 100644
--- a/drivers/net/cnic.h
+++ b/drivers/net/cnic.h
@@ -176,6 +176,7 @@ struct cnic_local {
 	unsigned long ulp_flags[MAX_CNIC_ULP_TYPE];
 #define ULP_F_INIT	0
 #define ULP_F_START	1
+#define ULP_F_CALL_PENDING	2
 	struct cnic_ulp_ops *ulp_ops[MAX_CNIC_ULP_TYPE];
 
 	/* protected by ulp_lock */
-- 
GitLab


From 7fc1ece40704b150477e548a7a98d285cc418790 Mon Sep 17 00:00:00 2001
From: Michael Chan <mchan@broadcom.com>
Date: Fri, 14 Aug 2009 15:49:47 +0000
Subject: [PATCH 0906/1153] cnic: Fix locking in init/exit calls.

The slow path ulp_init and ulp_exit calls to the bnx2i driver
are sleepable calls and therefore should not be protected using
rcu_read_lock.  Fix it by using mutex and refcount during these
calls.  cnic_unregister_driver() will now wait for the refcount
to go to zero before completing the call.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/cnic.c    | 48 +++++++++++++++++++++++++++++++++++--------
 drivers/net/cnic_if.h |  1 +
 2 files changed, 40 insertions(+), 9 deletions(-)

diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c
index 4ff618a7afd..74c342959b7 100644
--- a/drivers/net/cnic.c
+++ b/drivers/net/cnic.c
@@ -138,6 +138,16 @@ static struct cnic_dev *cnic_from_netdev(struct net_device *netdev)
 	return NULL;
 }
 
+static inline void ulp_get(struct cnic_ulp_ops *ulp_ops)
+{
+	atomic_inc(&ulp_ops->ref_count);
+}
+
+static inline void ulp_put(struct cnic_ulp_ops *ulp_ops)
+{
+	atomic_dec(&ulp_ops->ref_count);
+}
+
 static void cnic_ctx_wr(struct cnic_dev *dev, u32 cid_addr, u32 off, u32 val)
 {
 	struct cnic_local *cp = dev->cnic_priv;
@@ -358,6 +368,7 @@ int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops)
 	}
 	read_unlock(&cnic_dev_lock);
 
+	atomic_set(&ulp_ops->ref_count, 0);
 	rcu_assign_pointer(cnic_ulp_tbl[ulp_type], ulp_ops);
 	mutex_unlock(&cnic_lock);
 
@@ -379,6 +390,8 @@ int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops)
 int cnic_unregister_driver(int ulp_type)
 {
 	struct cnic_dev *dev;
+	struct cnic_ulp_ops *ulp_ops;
+	int i = 0;
 
 	if (ulp_type >= MAX_CNIC_ULP_TYPE) {
 		printk(KERN_ERR PFX "cnic_unregister_driver: Bad type %d\n",
@@ -386,7 +399,8 @@ int cnic_unregister_driver(int ulp_type)
 		return -EINVAL;
 	}
 	mutex_lock(&cnic_lock);
-	if (!cnic_ulp_tbl[ulp_type]) {
+	ulp_ops = cnic_ulp_tbl[ulp_type];
+	if (!ulp_ops) {
 		printk(KERN_ERR PFX "cnic_unregister_driver: Type %d has not "
 				    "been registered\n", ulp_type);
 		goto out_unlock;
@@ -411,6 +425,14 @@ int cnic_unregister_driver(int ulp_type)
 
 	mutex_unlock(&cnic_lock);
 	synchronize_rcu();
+	while ((atomic_read(&ulp_ops->ref_count) != 0) && (i < 20)) {
+		msleep(100);
+		i++;
+	}
+
+	if (atomic_read(&ulp_ops->ref_count) != 0)
+		printk(KERN_WARNING PFX "%s: Failed waiting for ref count to go"
+					" to zero.\n", dev->netdev->name);
 	return 0;
 
 out_unlock:
@@ -1161,19 +1183,23 @@ static void cnic_ulp_init(struct cnic_dev *dev)
 	int i;
 	struct cnic_local *cp = dev->cnic_priv;
 
-	rcu_read_lock();
 	for (i = 0; i < MAX_CNIC_ULP_TYPE_EXT; i++) {
 		struct cnic_ulp_ops *ulp_ops;
 
-		ulp_ops = rcu_dereference(cnic_ulp_tbl[i]);
-		if (!ulp_ops || !ulp_ops->cnic_init)
+		mutex_lock(&cnic_lock);
+		ulp_ops = cnic_ulp_tbl[i];
+		if (!ulp_ops || !ulp_ops->cnic_init) {
+			mutex_unlock(&cnic_lock);
 			continue;
+		}
+		ulp_get(ulp_ops);
+		mutex_unlock(&cnic_lock);
 
 		if (!test_and_set_bit(ULP_F_INIT, &cp->ulp_flags[i]))
 			ulp_ops->cnic_init(dev);
 
+		ulp_put(ulp_ops);
 	}
-	rcu_read_unlock();
 }
 
 static void cnic_ulp_exit(struct cnic_dev *dev)
@@ -1181,19 +1207,23 @@ static void cnic_ulp_exit(struct cnic_dev *dev)
 	int i;
 	struct cnic_local *cp = dev->cnic_priv;
 
-	rcu_read_lock();
 	for (i = 0; i < MAX_CNIC_ULP_TYPE_EXT; i++) {
 		struct cnic_ulp_ops *ulp_ops;
 
-		ulp_ops = rcu_dereference(cnic_ulp_tbl[i]);
-		if (!ulp_ops || !ulp_ops->cnic_exit)
+		mutex_lock(&cnic_lock);
+		ulp_ops = cnic_ulp_tbl[i];
+		if (!ulp_ops || !ulp_ops->cnic_exit) {
+			mutex_unlock(&cnic_lock);
 			continue;
+		}
+		ulp_get(ulp_ops);
+		mutex_unlock(&cnic_lock);
 
 		if (test_and_clear_bit(ULP_F_INIT, &cp->ulp_flags[i]))
 			ulp_ops->cnic_exit(dev);
 
+		ulp_put(ulp_ops);
 	}
-	rcu_read_unlock();
 }
 
 static int cnic_cm_offload_pg(struct cnic_sock *csk)
diff --git a/drivers/net/cnic_if.h b/drivers/net/cnic_if.h
index d1bce27ee99..a49235739ee 100644
--- a/drivers/net/cnic_if.h
+++ b/drivers/net/cnic_if.h
@@ -290,6 +290,7 @@ struct cnic_ulp_ops {
 	void (*iscsi_nl_send_msg)(struct cnic_dev *dev, u32 msg_type,
 				  char *data, u16 data_size);
 	struct module *owner;
+	atomic_t ref_count;
 };
 
 extern int cnic_register_driver(int ulp_type, struct cnic_ulp_ops *ulp_ops);
-- 
GitLab


From 82776a4bcd7aa5fbcd2e6339b3ce88b727dd40ab Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Fri, 14 Aug 2009 14:35:33 +0000
Subject: [PATCH 0907/1153] e1000e: WoL does not work on 82577/82578 with
 manageability enabled

With manageability (Intel AMT) enabled via BIOS, PHY wakeup does not get
configured on newer parts which use PHY wakeup vs. MAC wakeup which causes
WoL to not work.  The driver should configure PHY wakeup whether or not
manageability is enabled.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/e1000e/netdev.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 63415bb6f48..58e22fcb22b 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -4538,8 +4538,7 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
 		/* Allow time for pending master requests to run */
 		e1000e_disable_pcie_master(&adapter->hw);
 
-		if ((adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) &&
-		    !(hw->mac.ops.check_mng_mode(hw))) {
+		if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) {
 			/* enable wakeup by the PHY */
 			retval = e1000_init_phy_wakeup(adapter, wufc);
 			if (retval)
@@ -4557,7 +4556,8 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
 	*enable_wake = !!wufc;
 
 	/* make sure adapter isn't asleep if manageability is enabled */
-	if (adapter->flags & FLAG_MNG_PT_ENABLED)
+	if ((adapter->flags & FLAG_MNG_PT_ENABLED) ||
+	    (hw->mac.ops.check_mng_mode(hw)))
 		*enable_wake = true;
 
 	if (adapter->hw.phy.type == e1000_phy_igp_3)
-- 
GitLab


From 68eac4602b9104cdaa6c18b3edd914cececa6a1e Mon Sep 17 00:00:00 2001
From: Xiaotian Feng <dfeng@redhat.com>
Date: Fri, 14 Aug 2009 14:35:52 +0000
Subject: [PATCH 0908/1153] e1000e: fix use of pci_enable_pcie_error_reporting

commit 111b9dc5 ("e1000e: add aer support") introduces pcie aer
support for e1000e, but it is not reasonable to disable it in
e1000_remove but enable it in e1000_resume.  This patch enables aer
support in e1000_probe.

Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/e1000e/netdev.c | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 58e22fcb22b..fa92a683aef 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -4670,14 +4670,6 @@ static int e1000_resume(struct pci_dev *pdev)
 		return err;
 	}
 
-	/* AER (Advanced Error Reporting) hooks */
-	err = pci_enable_pcie_error_reporting(pdev);
-	if (err) {
-		dev_err(&pdev->dev, "pci_enable_pcie_error_reporting failed "
-		                    "0x%x\n", err);
-		/* non-fatal, continue */
-	}
-
 	pci_set_master(pdev);
 
 	pci_enable_wake(pdev, PCI_D3hot, 0);
@@ -4990,6 +4982,14 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 	if (err)
 		goto err_pci_reg;
 
+	/* AER (Advanced Error Reporting) hooks */
+	err = pci_enable_pcie_error_reporting(pdev);
+	if (err) {
+		dev_err(&pdev->dev, "pci_enable_pcie_error_reporting failed "
+		        "0x%x\n", err);
+		/* non-fatal, continue */
+	}
+
 	pci_set_master(pdev);
 	/* PCI config space info */
 	err = pci_save_state(pdev);
-- 
GitLab


From 4e5c25d405e18a2f279ca2bfc855508ec3a0186b Mon Sep 17 00:00:00 2001
From: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Date: Sun, 16 Aug 2009 15:54:37 +0100
Subject: [PATCH 0909/1153] x86, mce: therm_throt: Don't log redundant
 normality

0d01f31439c1e4d602bf9fdc924ab66f407f5e38 "x86, mce: therm_throt
- change when we print messages" removed redundant
announcements of "Temperature/speed normal".

They're not worth logging and remove their accompanying
"Machine check events logged" messages as well from the
console.

Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
LKML-Reference: <Pine.LNX.4.64.0908161544100.7929@sister.anvils>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/cpu/mcheck/therm_throt.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kernel/cpu/mcheck/therm_throt.c b/arch/x86/kernel/cpu/mcheck/therm_throt.c
index 8bc64cfbe93..5957a93e517 100644
--- a/arch/x86/kernel/cpu/mcheck/therm_throt.c
+++ b/arch/x86/kernel/cpu/mcheck/therm_throt.c
@@ -116,11 +116,14 @@ static int therm_throt_process(int curr)
 		       cpu, __get_cpu_var(thermal_throttle_count));
 
 		add_taint(TAINT_MACHINE_CHECK);
-	} else if (was_throttled) {
+		return 1;
+	}
+	if (was_throttled) {
 		printk(KERN_INFO "CPU%d: Temperature/speed normal\n", cpu);
+		return 1;
 	}
 
-	return 1;
+	return 0;
 }
 
 #ifdef CONFIG_SYSFS
-- 
GitLab


From 894ef820b10d77e2d6d717342fc408bdd9825139 Mon Sep 17 00:00:00 2001
From: Randy Dunlap <randy.dunlap@oracle.com>
Date: Sun, 16 Aug 2009 07:33:30 -0700
Subject: [PATCH 0910/1153] dm-log-userspace: fix printk format warning

drivers/md/dm-log-userspace-transfer.c:110: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'size_t'

Previously posted and acked, but apparently lost.
http://lkml.indiana.edu/hypermail/linux/kernel/0906.2/02074.html

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: dm-devel@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/md/dm-log-userspace-transfer.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/md/dm-log-userspace-transfer.c b/drivers/md/dm-log-userspace-transfer.c
index 0ca1ee768a1..8ce74d95ae4 100644
--- a/drivers/md/dm-log-userspace-transfer.c
+++ b/drivers/md/dm-log-userspace-transfer.c
@@ -108,7 +108,7 @@ static int fill_pkg(struct cn_msg *msg, struct dm_ulog_request *tfr)
 				*(pkg->data_size) = 0;
 		} else if (tfr->data_size > *(pkg->data_size)) {
 			DMERR("Insufficient space to receive package [%u] "
-			      "(%u vs %lu)", tfr->request_type,
+			      "(%u vs %zu)", tfr->request_type,
 			      tfr->data_size, *(pkg->data_size));
 
 			*(pkg->data_size) = 0;
-- 
GitLab


From 52459ab91363343af8ae252766e9da762344a2e7 Mon Sep 17 00:00:00 2001
From: Leonardo Potenza <lpotenza@inwind.it>
Date: Sun, 16 Aug 2009 18:55:48 +0200
Subject: [PATCH 0911/1153] x86: Annotate section mismatch warnings in
 kernel/apic/x2apic_uv_x.c

The function uv_acpi_madt_oem_check() has been marked __init,
the struct apic_x2apic_uv_x has been marked __refdata.

The aim is to address the following section mismatch messages:

WARNING: arch/x86/kernel/apic/built-in.o(.data+0x1368): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: arch/x86/kernel/built-in.o(.data+0x68e8): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: arch/x86/built-in.o(.text+0x7b36f): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_ioremap()
The function uv_acpi_madt_oem_check() references
the function __init early_ioremap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_ioremap is wrong.

WARNING: arch/x86/built-in.o(.text+0x7b38d): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_iounmap()
The function uv_acpi_madt_oem_check() references
the function __init early_iounmap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_iounmap is wrong.

WARNING: arch/x86/built-in.o(.data+0x8668): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
LKML-Reference: <200908161855.48302.lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/apic/x2apic_uv_x.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c
index 832e908adcb..601159374e8 100644
--- a/arch/x86/kernel/apic/x2apic_uv_x.c
+++ b/arch/x86/kernel/apic/x2apic_uv_x.c
@@ -46,7 +46,7 @@ static int early_get_nodeid(void)
 	return node_id.s.node_id;
 }
 
-static int uv_acpi_madt_oem_check(char *oem_id, char *oem_table_id)
+static int __init uv_acpi_madt_oem_check(char *oem_id, char *oem_table_id)
 {
 	if (!strcmp(oem_id, "SGI")) {
 		if (!strcmp(oem_table_id, "UVL"))
@@ -253,7 +253,7 @@ static void uv_send_IPI_self(int vector)
 	apic_write(APIC_SELF_IPI, vector);
 }
 
-struct apic apic_x2apic_uv_x = {
+struct apic __refdata apic_x2apic_uv_x = {
 
 	.name				= "UV large system",
 	.probe				= NULL,
-- 
GitLab


From cefb87efc9aa0288849149484870d5ab989fbd59 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Sun, 16 Aug 2009 21:05:45 +1000
Subject: [PATCH 0912/1153] drm/radeon/kms: implement bo busy check + current
 domain

This implements the busy ioctl along with a current domain check.
returns 0 or -EBUSY
puts the current domain no matter what the answer.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon.h        |  1 +
 drivers/gpu/drm/radeon/radeon_gem.c    | 22 +++++++++++++++++++++-
 drivers/gpu/drm/radeon/radeon_object.c | 19 +++++++++++++++++++
 include/drm/radeon_drm.h               |  2 +-
 4 files changed, 42 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index 87170a56e37..79ad98264e3 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -242,6 +242,7 @@ int radeon_object_pin(struct radeon_object *robj, uint32_t domain,
 		      uint64_t *gpu_addr);
 void radeon_object_unpin(struct radeon_object *robj);
 int radeon_object_wait(struct radeon_object *robj);
+int radeon_object_busy_domain(struct radeon_object *robj, uint32_t *cur_placement);
 int radeon_object_evict_vram(struct radeon_device *rdev);
 int radeon_object_mmap(struct radeon_object *robj, uint64_t *offset);
 void radeon_object_force_delete(struct radeon_device *rdev);
diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c
index cded5180c75..d4ceff13bbb 100644
--- a/drivers/gpu/drm/radeon/radeon_gem.c
+++ b/drivers/gpu/drm/radeon/radeon_gem.c
@@ -262,7 +262,27 @@ int radeon_gem_mmap_ioctl(struct drm_device *dev, void *data,
 int radeon_gem_busy_ioctl(struct drm_device *dev, void *data,
 			  struct drm_file *filp)
 {
-	/* FIXME: implement */
+	struct drm_radeon_gem_busy *args = data;
+	struct drm_gem_object *gobj;
+	struct radeon_object *robj;
+	int r;
+	uint32_t cur_placement;
+
+	gobj = drm_gem_object_lookup(dev, filp, args->handle);
+	if (gobj == NULL) {
+		return -EINVAL;
+	}
+	robj = gobj->driver_private;
+	r = radeon_object_busy_domain(robj, &cur_placement);
+	if (cur_placement == TTM_PL_VRAM)
+		args->domain = RADEON_GEM_DOMAIN_VRAM;
+	if (cur_placement == TTM_PL_FLAG_TT)
+		args->domain = RADEON_GEM_DOMAIN_GTT;
+	if (cur_placement == TTM_PL_FLAG_SYSTEM)
+		args->domain = RADEON_GEM_DOMAIN_CPU;
+	mutex_lock(&dev->struct_mutex);
+	drm_gem_object_unreference(gobj);
+	mutex_unlock(&dev->struct_mutex);
 	return 0;
 }
 
diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c
index e98cae3bf4a..b85fb83d7ae 100644
--- a/drivers/gpu/drm/radeon/radeon_object.c
+++ b/drivers/gpu/drm/radeon/radeon_object.c
@@ -316,6 +316,25 @@ int radeon_object_wait(struct radeon_object *robj)
 	return r;
 }
 
+int radeon_object_busy_domain(struct radeon_object *robj, uint32_t *cur_placement)
+{
+	int r = 0;
+
+	r = radeon_object_reserve(robj, true);
+	if (unlikely(r != 0)) {
+		DRM_ERROR("radeon: failed to reserve object for waiting.\n");
+		return r;
+	}
+	spin_lock(&robj->tobj.lock);
+	*cur_placement = robj->tobj.mem.mem_type;
+	if (robj->tobj.sync_obj) {
+		r = ttm_bo_wait(&robj->tobj, true, true, true);
+	}
+	spin_unlock(&robj->tobj.lock);
+	radeon_object_unreserve(robj);
+	return r;
+}
+
 int radeon_object_evict_vram(struct radeon_device *rdev)
 {
 	if (rdev->flags & RADEON_IS_IGP) {
diff --git a/include/drm/radeon_drm.h b/include/drm/radeon_drm.h
index af4b4826997..f81c3232acc 100644
--- a/include/drm/radeon_drm.h
+++ b/include/drm/radeon_drm.h
@@ -838,7 +838,7 @@ struct drm_radeon_gem_wait_idle {
 
 struct drm_radeon_gem_busy {
 	uint32_t	handle;
-	uint32_t	busy;
+	uint32_t        domain;
 };
 
 struct drm_radeon_gem_pread {
-- 
GitLab


From 9c0d90103c7e0eb6e638e5b649e9f6d8d9c1b4b3 Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Fri, 31 Jul 2009 12:53:58 -0400
Subject: [PATCH 0913/1153] Capabilities: move cap_file_mmap to commoncap.c

Currently we duplicate the mmap_min_addr test in cap_file_mmap and in
security_file_mmap if !CONFIG_SECURITY.  This patch moves cap_file_mmap
into commoncap.c and then calls that function directly from
security_file_mmap ifndef CONFIG_SECURITY like all of the other capability
checks are done.

Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 include/linux/security.h |  7 ++++---
 security/capability.c    |  9 ---------
 security/commoncap.c     | 30 ++++++++++++++++++++++++++++++
 3 files changed, 34 insertions(+), 12 deletions(-)

diff --git a/include/linux/security.h b/include/linux/security.h
index 5eff459b383..ac4bc3760b4 100644
--- a/include/linux/security.h
+++ b/include/linux/security.h
@@ -66,6 +66,9 @@ extern int cap_inode_setxattr(struct dentry *dentry, const char *name,
 extern int cap_inode_removexattr(struct dentry *dentry, const char *name);
 extern int cap_inode_need_killpriv(struct dentry *dentry);
 extern int cap_inode_killpriv(struct dentry *dentry);
+extern int cap_file_mmap(struct file *file, unsigned long reqprot,
+			 unsigned long prot, unsigned long flags,
+			 unsigned long addr, unsigned long addr_only);
 extern int cap_task_fix_setuid(struct cred *new, const struct cred *old, int flags);
 extern int cap_task_prctl(int option, unsigned long arg2, unsigned long arg3,
 			  unsigned long arg4, unsigned long arg5);
@@ -2197,9 +2200,7 @@ static inline int security_file_mmap(struct file *file, unsigned long reqprot,
 				     unsigned long addr,
 				     unsigned long addr_only)
 {
-	if ((addr < mmap_min_addr) && !capable(CAP_SYS_RAWIO))
-		return -EACCES;
-	return 0;
+	return cap_file_mmap(file, reqprot, prot, flags, addr, addr_only);
 }
 
 static inline int security_file_mprotect(struct vm_area_struct *vma,
diff --git a/security/capability.c b/security/capability.c
index 21b6cead6a8..88f752e8152 100644
--- a/security/capability.c
+++ b/security/capability.c
@@ -330,15 +330,6 @@ static int cap_file_ioctl(struct file *file, unsigned int command,
 	return 0;
 }
 
-static int cap_file_mmap(struct file *file, unsigned long reqprot,
-			 unsigned long prot, unsigned long flags,
-			 unsigned long addr, unsigned long addr_only)
-{
-	if ((addr < mmap_min_addr) && !capable(CAP_SYS_RAWIO))
-		return -EACCES;
-	return 0;
-}
-
 static int cap_file_mprotect(struct vm_area_struct *vma, unsigned long reqprot,
 			     unsigned long prot)
 {
diff --git a/security/commoncap.c b/security/commoncap.c
index 48b7e0228fa..6bcf6e81e54 100644
--- a/security/commoncap.c
+++ b/security/commoncap.c
@@ -984,3 +984,33 @@ int cap_vm_enough_memory(struct mm_struct *mm, long pages)
 		cap_sys_admin = 1;
 	return __vm_enough_memory(mm, pages, cap_sys_admin);
 }
+
+/*
+ * cap_file_mmap - check if able to map given addr
+ * @file: unused
+ * @reqprot: unused
+ * @prot: unused
+ * @flags: unused
+ * @addr: address attempting to be mapped
+ * @addr_only: unused
+ *
+ * If the process is attempting to map memory below mmap_min_addr they need
+ * CAP_SYS_RAWIO.  The other parameters to this function are unused by the
+ * capability security module.  Returns 0 if this mapping should be allowed
+ * -EPERM if not.
+ */
+int cap_file_mmap(struct file *file, unsigned long reqprot,
+		  unsigned long prot, unsigned long flags,
+		  unsigned long addr, unsigned long addr_only)
+{
+	int ret = 0;
+
+	if (addr < mmap_min_addr) {
+		ret = cap_capable(current, current_cred(), CAP_SYS_RAWIO,
+				  SECURITY_CAP_AUDIT);
+		/* set PF_SUPERPRIV if it turns out we allow the low mmap */
+		if (ret == 0)
+			current->flags |= PF_SUPERPRIV;
+	}
+	return ret;
+}
-- 
GitLab


From 8cf948e744e0218af604c32edecde10006dc8e9e Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Fri, 31 Jul 2009 12:54:05 -0400
Subject: [PATCH 0914/1153] SELinux: call cap_file_mmap in selinux_file_mmap

Currently SELinux does not check CAP_SYS_RAWIO in the file_mmap hook.  This
means there is no DAC check on the ability to mmap low addresses in the
memory space.  This function adds the DAC check for CAP_SYS_RAWIO while
maintaining the selinux check on mmap_zero.  This means that processes
which need to mmap low memory will need CAP_SYS_RAWIO and mmap_zero but will
NOT need the SELinux sys_rawio capability.

Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 security/selinux/hooks.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)

diff --git a/security/selinux/hooks.c b/security/selinux/hooks.c
index 1e8cfc4c2ed..e6d1432b080 100644
--- a/security/selinux/hooks.c
+++ b/security/selinux/hooks.c
@@ -3030,9 +3030,21 @@ static int selinux_file_mmap(struct file *file, unsigned long reqprot,
 	int rc = 0;
 	u32 sid = current_sid();
 
-	if (addr < mmap_min_addr)
+	/*
+	 * notice that we are intentionally putting the SELinux check before
+	 * the secondary cap_file_mmap check.  This is such a likely attempt
+	 * at bad behaviour/exploit that we always want to get the AVC, even
+	 * if DAC would have also denied the operation.
+	 */
+	if (addr < mmap_min_addr) {
 		rc = avc_has_perm(sid, sid, SECCLASS_MEMPROTECT,
 				  MEMPROTECT__MMAP_ZERO, NULL);
+		if (rc)
+			return rc;
+	}
+
+	/* do DAC check on address space usage */
+	rc = cap_file_mmap(file, reqprot, prot, flags, addr, addr_only);
 	if (rc || addr_only)
 		return rc;
 
-- 
GitLab


From 788084aba2ab7348257597496befcbccabdc98a3 Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Fri, 31 Jul 2009 12:54:11 -0400
Subject: [PATCH 0915/1153] Security/SELinux: seperate lsm specific
 mmap_min_addr

Currently SELinux enforcement of controls on the ability to map low memory
is determined by the mmap_min_addr tunable.  This patch causes SELinux to
ignore the tunable and instead use a seperate Kconfig option specific to how
much space the LSM should protect.

The tunable will now only control the need for CAP_SYS_RAWIO and SELinux
permissions will always protect the amount of low memory designated by
CONFIG_LSM_MMAP_MIN_ADDR.

This allows users who need to disable the mmap_min_addr controls (usual reason
being they run WINE as a non-root user) to do so and still have SELinux
controls preventing confined domains (like a web server) from being able to
map some area of low memory.

Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 include/linux/mm.h       | 15 ------------
 include/linux/security.h | 17 ++++++++++++++
 kernel/sysctl.c          |  7 +++---
 mm/Kconfig               |  6 ++---
 mm/mmap.c                |  3 ---
 mm/nommu.c               |  3 ---
 security/Kconfig         | 16 +++++++++++++
 security/Makefile        |  2 +-
 security/commoncap.c     |  2 +-
 security/min_addr.c      | 49 ++++++++++++++++++++++++++++++++++++++++
 security/selinux/hooks.c |  2 +-
 11 files changed, 92 insertions(+), 30 deletions(-)
 create mode 100644 security/min_addr.c

diff --git a/include/linux/mm.h b/include/linux/mm.h
index ba3a7cb1eaa..9a72cc78e6b 100644
--- a/include/linux/mm.h
+++ b/include/linux/mm.h
@@ -34,8 +34,6 @@ extern int sysctl_legacy_va_layout;
 #define sysctl_legacy_va_layout 0
 #endif
 
-extern unsigned long mmap_min_addr;
-
 #include <asm/page.h>
 #include <asm/pgtable.h>
 #include <asm/processor.h>
@@ -574,19 +572,6 @@ static inline void set_page_links(struct page *page, enum zone_type zone,
 	set_page_section(page, pfn_to_section_nr(pfn));
 }
 
-/*
- * If a hint addr is less than mmap_min_addr change hint to be as
- * low as possible but still greater than mmap_min_addr
- */
-static inline unsigned long round_hint_to_min(unsigned long hint)
-{
-	hint &= PAGE_MASK;
-	if (((void *)hint != NULL) &&
-	    (hint < mmap_min_addr))
-		return PAGE_ALIGN(mmap_min_addr);
-	return hint;
-}
-
 /*
  * Some inline functions in vmstat.h depend on page_zone()
  */
diff --git a/include/linux/security.h b/include/linux/security.h
index ac4bc3760b4..dc3472c1f78 100644
--- a/include/linux/security.h
+++ b/include/linux/security.h
@@ -28,6 +28,7 @@
 #include <linux/resource.h>
 #include <linux/sem.h>
 #include <linux/shm.h>
+#include <linux/mm.h> /* PAGE_ALIGN */
 #include <linux/msg.h>
 #include <linux/sched.h>
 #include <linux/key.h>
@@ -95,6 +96,7 @@ extern int cap_netlink_send(struct sock *sk, struct sk_buff *skb);
 extern int cap_netlink_recv(struct sk_buff *skb, int cap);
 
 extern unsigned long mmap_min_addr;
+extern unsigned long dac_mmap_min_addr;
 /*
  * Values used in the task_security_ops calls
  */
@@ -147,6 +149,21 @@ static inline void security_free_mnt_opts(struct security_mnt_opts *opts)
 	opts->num_mnt_opts = 0;
 }
 
+/*
+ * If a hint addr is less than mmap_min_addr change hint to be as
+ * low as possible but still greater than mmap_min_addr
+ */
+static inline unsigned long round_hint_to_min(unsigned long hint)
+{
+	hint &= PAGE_MASK;
+	if (((void *)hint != NULL) &&
+	    (hint < mmap_min_addr))
+		return PAGE_ALIGN(mmap_min_addr);
+	return hint;
+}
+
+extern int mmap_min_addr_handler(struct ctl_table *table, int write, struct file *filp,
+				 void __user *buffer, size_t *lenp, loff_t *ppos);
 /**
  * struct security_operations - main security structure
  *
diff --git a/kernel/sysctl.c b/kernel/sysctl.c
index 98e02328c67..58be76017fd 100644
--- a/kernel/sysctl.c
+++ b/kernel/sysctl.c
@@ -49,6 +49,7 @@
 #include <linux/acpi.h>
 #include <linux/reboot.h>
 #include <linux/ftrace.h>
+#include <linux/security.h>
 #include <linux/slow-work.h>
 #include <linux/perf_counter.h>
 
@@ -1306,10 +1307,10 @@ static struct ctl_table vm_table[] = {
 	{
 		.ctl_name	= CTL_UNNUMBERED,
 		.procname	= "mmap_min_addr",
-		.data		= &mmap_min_addr,
-		.maxlen         = sizeof(unsigned long),
+		.data		= &dac_mmap_min_addr,
+		.maxlen		= sizeof(unsigned long),
 		.mode		= 0644,
-		.proc_handler	= &proc_doulongvec_minmax,
+		.proc_handler	= &mmap_min_addr_handler,
 	},
 #ifdef CONFIG_NUMA
 	{
diff --git a/mm/Kconfig b/mm/Kconfig
index c948d4ca8bd..fe5f674d7a7 100644
--- a/mm/Kconfig
+++ b/mm/Kconfig
@@ -225,9 +225,9 @@ config DEFAULT_MMAP_MIN_ADDR
 	  For most ia64, ppc64 and x86 users with lots of address space
 	  a value of 65536 is reasonable and should cause no problems.
 	  On arm and other archs it should not be higher than 32768.
-	  Programs which use vm86 functionality would either need additional
-	  permissions from either the LSM or the capabilities module or have
-	  this protection disabled.
+	  Programs which use vm86 functionality or have some need to map
+	  this low address space will need CAP_SYS_RAWIO or disable this
+	  protection by setting the value to 0.
 
 	  This value can be changed after boot using the
 	  /proc/sys/vm/mmap_min_addr tunable.
diff --git a/mm/mmap.c b/mm/mmap.c
index 34579b23ebd..8101de490c7 100644
--- a/mm/mmap.c
+++ b/mm/mmap.c
@@ -88,9 +88,6 @@ int sysctl_overcommit_ratio = 50;	/* default is 50% */
 int sysctl_max_map_count __read_mostly = DEFAULT_MAX_MAP_COUNT;
 struct percpu_counter vm_committed_as;
 
-/* amount of vm to protect from userspace access */
-unsigned long mmap_min_addr = CONFIG_DEFAULT_MMAP_MIN_ADDR;
-
 /*
  * Check that a process has enough memory to allocate a new virtual
  * mapping. 0 means there is enough memory for the allocation to
diff --git a/mm/nommu.c b/mm/nommu.c
index 53cab10fece..28754c40be9 100644
--- a/mm/nommu.c
+++ b/mm/nommu.c
@@ -69,9 +69,6 @@ int sysctl_max_map_count = DEFAULT_MAX_MAP_COUNT;
 int sysctl_nr_trim_pages = CONFIG_NOMMU_INITIAL_TRIM_EXCESS;
 int heap_stack_gap = 0;
 
-/* amount of vm to protect from userspace access */
-unsigned long mmap_min_addr = CONFIG_DEFAULT_MMAP_MIN_ADDR;
-
 atomic_long_t mmap_pages_allocated;
 
 EXPORT_SYMBOL(mem_map);
diff --git a/security/Kconfig b/security/Kconfig
index d23c839038f..9c60c346a91 100644
--- a/security/Kconfig
+++ b/security/Kconfig
@@ -113,6 +113,22 @@ config SECURITY_ROOTPLUG
 
 	  If you are unsure how to answer this question, answer N.
 
+config LSM_MMAP_MIN_ADDR
+	int "Low address space for LSM to from user allocation"
+	depends on SECURITY && SECURITY_SELINUX
+	default 65535
+	help
+	  This is the portion of low virtual memory which should be protected
+	  from userspace allocation.  Keeping a user from writing to low pages
+	  can help reduce the impact of kernel NULL pointer bugs.
+
+	  For most ia64, ppc64 and x86 users with lots of address space
+	  a value of 65536 is reasonable and should cause no problems.
+	  On arm and other archs it should not be higher than 32768.
+	  Programs which use vm86 functionality or have some need to map
+	  this low address space will need the permission specific to the
+	  systems running LSM.
+
 source security/selinux/Kconfig
 source security/smack/Kconfig
 source security/tomoyo/Kconfig
diff --git a/security/Makefile b/security/Makefile
index c67557cdaa8..b56e7f9ecbc 100644
--- a/security/Makefile
+++ b/security/Makefile
@@ -8,7 +8,7 @@ subdir-$(CONFIG_SECURITY_SMACK)		+= smack
 subdir-$(CONFIG_SECURITY_TOMOYO)        += tomoyo
 
 # always enable default capabilities
-obj-y		+= commoncap.o
+obj-y		+= commoncap.o min_addr.o
 
 # Object file lists
 obj-$(CONFIG_SECURITY)			+= security.o capability.o
diff --git a/security/commoncap.c b/security/commoncap.c
index 6bcf6e81e54..e3097c0a131 100644
--- a/security/commoncap.c
+++ b/security/commoncap.c
@@ -1005,7 +1005,7 @@ int cap_file_mmap(struct file *file, unsigned long reqprot,
 {
 	int ret = 0;
 
-	if (addr < mmap_min_addr) {
+	if (addr < dac_mmap_min_addr) {
 		ret = cap_capable(current, current_cred(), CAP_SYS_RAWIO,
 				  SECURITY_CAP_AUDIT);
 		/* set PF_SUPERPRIV if it turns out we allow the low mmap */
diff --git a/security/min_addr.c b/security/min_addr.c
new file mode 100644
index 00000000000..14cc7b3b8d0
--- /dev/null
+++ b/security/min_addr.c
@@ -0,0 +1,49 @@
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/security.h>
+#include <linux/sysctl.h>
+
+/* amount of vm to protect from userspace access by both DAC and the LSM*/
+unsigned long mmap_min_addr;
+/* amount of vm to protect from userspace using CAP_SYS_RAWIO (DAC) */
+unsigned long dac_mmap_min_addr = CONFIG_DEFAULT_MMAP_MIN_ADDR;
+/* amount of vm to protect from userspace using the LSM = CONFIG_LSM_MMAP_MIN_ADDR */
+
+/*
+ * Update mmap_min_addr = max(dac_mmap_min_addr, CONFIG_LSM_MMAP_MIN_ADDR)
+ */
+static void update_mmap_min_addr(void)
+{
+#ifdef CONFIG_LSM_MMAP_MIN_ADDR
+	if (dac_mmap_min_addr > CONFIG_LSM_MMAP_MIN_ADDR)
+		mmap_min_addr = dac_mmap_min_addr;
+	else
+		mmap_min_addr = CONFIG_LSM_MMAP_MIN_ADDR;
+#else
+	mmap_min_addr = dac_mmap_min_addr;
+#endif
+}
+
+/*
+ * sysctl handler which just sets dac_mmap_min_addr = the new value and then
+ * calls update_mmap_min_addr() so non MAP_FIXED hints get rounded properly
+ */
+int mmap_min_addr_handler(struct ctl_table *table, int write, struct file *filp,
+			  void __user *buffer, size_t *lenp, loff_t *ppos)
+{
+	int ret;
+
+	ret = proc_doulongvec_minmax(table, write, filp, buffer, lenp, ppos);
+
+	update_mmap_min_addr();
+
+	return ret;
+}
+
+int __init init_mmap_min_addr(void)
+{
+	update_mmap_min_addr();
+
+	return 0;
+}
+pure_initcall(init_mmap_min_addr);
diff --git a/security/selinux/hooks.c b/security/selinux/hooks.c
index e6d1432b080..8d8b69c5664 100644
--- a/security/selinux/hooks.c
+++ b/security/selinux/hooks.c
@@ -3036,7 +3036,7 @@ static int selinux_file_mmap(struct file *file, unsigned long reqprot,
 	 * at bad behaviour/exploit that we always want to get the AVC, even
 	 * if DAC would have also denied the operation.
 	 */
-	if (addr < mmap_min_addr) {
+	if (addr < CONFIG_LSM_MMAP_MIN_ADDR) {
 		rc = avc_has_perm(sid, sid, SECCLASS_MEMPROTECT,
 				  MEMPROTECT__MMAP_ZERO, NULL);
 		if (rc)
-- 
GitLab


From 1d9959734a1949ea4f2427bd2d8b21ede6b2441c Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Fri, 7 Aug 2009 14:53:57 -0400
Subject: [PATCH 0916/1153] security: define round_hint_to_min in
 !CONFIG_SECURITY

Fix the header files to define round_hint_to_min() and to define
mmap_min_addr_handler() in the !CONFIG_SECURITY case.

Built and tested with !CONFIG_SECURITY

Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 include/linux/security.h | 30 +++++++++++++++---------------
 1 file changed, 15 insertions(+), 15 deletions(-)

diff --git a/include/linux/security.h b/include/linux/security.h
index dc3472c1f78..1f16eea2017 100644
--- a/include/linux/security.h
+++ b/include/linux/security.h
@@ -121,6 +121,21 @@ struct request_sock;
 #define LSM_UNSAFE_PTRACE	2
 #define LSM_UNSAFE_PTRACE_CAP	4
 
+/*
+ * If a hint addr is less than mmap_min_addr change hint to be as
+ * low as possible but still greater than mmap_min_addr
+ */
+static inline unsigned long round_hint_to_min(unsigned long hint)
+{
+	hint &= PAGE_MASK;
+	if (((void *)hint != NULL) &&
+	    (hint < mmap_min_addr))
+		return PAGE_ALIGN(mmap_min_addr);
+	return hint;
+}
+extern int mmap_min_addr_handler(struct ctl_table *table, int write, struct file *filp,
+				 void __user *buffer, size_t *lenp, loff_t *ppos);
+
 #ifdef CONFIG_SECURITY
 
 struct security_mnt_opts {
@@ -149,21 +164,6 @@ static inline void security_free_mnt_opts(struct security_mnt_opts *opts)
 	opts->num_mnt_opts = 0;
 }
 
-/*
- * If a hint addr is less than mmap_min_addr change hint to be as
- * low as possible but still greater than mmap_min_addr
- */
-static inline unsigned long round_hint_to_min(unsigned long hint)
-{
-	hint &= PAGE_MASK;
-	if (((void *)hint != NULL) &&
-	    (hint < mmap_min_addr))
-		return PAGE_ALIGN(mmap_min_addr);
-	return hint;
-}
-
-extern int mmap_min_addr_handler(struct ctl_table *table, int write, struct file *filp,
-				 void __user *buffer, size_t *lenp, loff_t *ppos);
 /**
  * struct security_operations - main security structure
  *
-- 
GitLab


From bc990f5cb424cdca9dda866785d088e2c2110ecc Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@infradead.org>
Date: Sun, 16 Aug 2009 20:36:34 -0400
Subject: [PATCH 0917/1153] xfs: fix locking in xfs_iget_cache_hit

The locking in xfs_iget_cache_hit currently has numerous problems:

 - we clear the reclaim tag without i_flags_lock which protects
   modifications to it
 - we call inode_init_always which can sleep with pag_ici_lock
   held (this is oss.sgi.com BZ #819)
 - we acquire and drop i_flags_lock a lot and thus provide no
   consistency between the various flags we set/clear under it

This patch fixes all that with a major revamp of the locking in
the function.  The new version acquires i_flags_lock early and
only drops it once we need to call into inode_init_always or before
calling xfs_ilock.

This patch fixes a bug seen in the wild where we race modifying the
reclaim tag.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
---
 fs/xfs/linux-2.6/xfs_sync.c |  13 ++++-
 fs/xfs/linux-2.6/xfs_sync.h |   1 +
 fs/xfs/xfs_iget.c           | 113 ++++++++++++++++++------------------
 3 files changed, 70 insertions(+), 57 deletions(-)

diff --git a/fs/xfs/linux-2.6/xfs_sync.c b/fs/xfs/linux-2.6/xfs_sync.c
index b619d6b8ca4..98ef624d9ba 100644
--- a/fs/xfs/linux-2.6/xfs_sync.c
+++ b/fs/xfs/linux-2.6/xfs_sync.c
@@ -708,6 +708,16 @@ xfs_reclaim_inode(
 	return 0;
 }
 
+void
+__xfs_inode_set_reclaim_tag(
+	struct xfs_perag	*pag,
+	struct xfs_inode	*ip)
+{
+	radix_tree_tag_set(&pag->pag_ici_root,
+			   XFS_INO_TO_AGINO(ip->i_mount, ip->i_ino),
+			   XFS_ICI_RECLAIM_TAG);
+}
+
 /*
  * We set the inode flag atomically with the radix tree tag.
  * Once we get tag lookups on the radix tree, this inode flag
@@ -722,8 +732,7 @@ xfs_inode_set_reclaim_tag(
 
 	read_lock(&pag->pag_ici_lock);
 	spin_lock(&ip->i_flags_lock);
-	radix_tree_tag_set(&pag->pag_ici_root,
-			XFS_INO_TO_AGINO(mp, ip->i_ino), XFS_ICI_RECLAIM_TAG);
+	__xfs_inode_set_reclaim_tag(pag, ip);
 	__xfs_iflags_set(ip, XFS_IRECLAIMABLE);
 	spin_unlock(&ip->i_flags_lock);
 	read_unlock(&pag->pag_ici_lock);
diff --git a/fs/xfs/linux-2.6/xfs_sync.h b/fs/xfs/linux-2.6/xfs_sync.h
index 2a10301c99c..59120602588 100644
--- a/fs/xfs/linux-2.6/xfs_sync.h
+++ b/fs/xfs/linux-2.6/xfs_sync.h
@@ -48,6 +48,7 @@ int xfs_reclaim_inode(struct xfs_inode *ip, int locked, int sync_mode);
 int xfs_reclaim_inodes(struct xfs_mount *mp, int mode);
 
 void xfs_inode_set_reclaim_tag(struct xfs_inode *ip);
+void __xfs_inode_set_reclaim_tag(struct xfs_perag *pag, struct xfs_inode *ip);
 void xfs_inode_clear_reclaim_tag(struct xfs_inode *ip);
 void __xfs_inode_clear_reclaim_tag(struct xfs_mount *mp, struct xfs_perag *pag,
 				struct xfs_inode *ip);
diff --git a/fs/xfs/xfs_iget.c b/fs/xfs/xfs_iget.c
index 34ec86923f7..ecbf8b4d2e2 100644
--- a/fs/xfs/xfs_iget.c
+++ b/fs/xfs/xfs_iget.c
@@ -191,80 +191,82 @@ xfs_iget_cache_hit(
 	int			flags,
 	int			lock_flags) __releases(pag->pag_ici_lock)
 {
+	struct inode		*inode = VFS_I(ip);
 	struct xfs_mount	*mp = ip->i_mount;
-	int			error = EAGAIN;
+	int			error;
+
+	spin_lock(&ip->i_flags_lock);
 
 	/*
-	 * If INEW is set this inode is being set up
-	 * If IRECLAIM is set this inode is being torn down
-	 * Pause and try again.
+	 * If we are racing with another cache hit that is currently
+	 * instantiating this inode or currently recycling it out of
+	 * reclaimabe state, wait for the initialisation to complete
+	 * before continuing.
+	 *
+	 * XXX(hch): eventually we should do something equivalent to
+	 *	     wait_on_inode to wait for these flags to be cleared
+	 *	     instead of polling for it.
 	 */
-	if (xfs_iflags_test(ip, (XFS_INEW|XFS_IRECLAIM))) {
+	if (ip->i_flags & (XFS_INEW|XFS_IRECLAIM)) {
 		XFS_STATS_INC(xs_ig_frecycle);
+		error = EAGAIN;
 		goto out_error;
 	}
 
-	/* If IRECLAIMABLE is set, we've torn down the vfs inode part */
-	if (xfs_iflags_test(ip, XFS_IRECLAIMABLE)) {
-
-		/*
-		 * If lookup is racing with unlink, then we should return an
-		 * error immediately so we don't remove it from the reclaim
-		 * list and potentially leak the inode.
-		 */
-		if ((ip->i_d.di_mode == 0) && !(flags & XFS_IGET_CREATE)) {
-			error = ENOENT;
-			goto out_error;
-		}
+	/*
+	 * If lookup is racing with unlink return an error immediately.
+	 */
+	if (ip->i_d.di_mode == 0 && !(flags & XFS_IGET_CREATE)) {
+		error = ENOENT;
+		goto out_error;
+	}
 
+	/*
+	 * If IRECLAIMABLE is set, we've torn down the VFS inode already.
+	 * Need to carefully get it back into useable state.
+	 */
+	if (ip->i_flags & XFS_IRECLAIMABLE) {
 		xfs_itrace_exit_tag(ip, "xfs_iget.alloc");
 
 		/*
-		 * We need to re-initialise the VFS inode as it has been
-		 * 'freed' by the VFS. Do this here so we can deal with
-		 * errors cleanly, then tag it so it can be set up correctly
-		 * later.
+		 * We need to set XFS_INEW atomically with clearing the
+		 * reclaimable tag so that we do have an indicator of the
+		 * inode still being initialized.
 		 */
-		if (inode_init_always(mp->m_super, VFS_I(ip))) {
-			error = ENOMEM;
-			goto out_error;
-		}
+		ip->i_flags |= XFS_INEW;
+		ip->i_flags &= ~XFS_IRECLAIMABLE;
+		__xfs_inode_clear_reclaim_tag(mp, pag, ip);
 
-		/*
-		 * We must set the XFS_INEW flag before clearing the
-		 * XFS_IRECLAIMABLE flag so that if a racing lookup does
-		 * not find the XFS_IRECLAIMABLE above but has the igrab()
-		 * below succeed we can safely check XFS_INEW to detect
-		 * that this inode is still being initialised.
-		 */
-		xfs_iflags_set(ip, XFS_INEW);
-		xfs_iflags_clear(ip, XFS_IRECLAIMABLE);
+		spin_unlock(&ip->i_flags_lock);
+		read_unlock(&pag->pag_ici_lock);
 
-		/* clear the radix tree reclaim flag as well. */
-		__xfs_inode_clear_reclaim_tag(mp, pag, ip);
-	} else if (!igrab(VFS_I(ip))) {
+		error = -inode_init_always(mp->m_super, inode);
+		if (error) {
+			/*
+			 * Re-initializing the inode failed, and we are in deep
+			 * trouble.  Try to re-add it to the reclaim list.
+			 */
+			read_lock(&pag->pag_ici_lock);
+			spin_lock(&ip->i_flags_lock);
+
+			ip->i_flags &= ~XFS_INEW;
+			ip->i_flags |= XFS_IRECLAIMABLE;
+			__xfs_inode_set_reclaim_tag(pag, ip);
+			goto out_error;
+		}
+		inode->i_state = I_LOCK|I_NEW;
+	} else {
 		/* If the VFS inode is being torn down, pause and try again. */
-		XFS_STATS_INC(xs_ig_frecycle);
-		goto out_error;
-	} else if (xfs_iflags_test(ip, XFS_INEW)) {
-		/*
-		 * We are racing with another cache hit that is
-		 * currently recycling this inode out of the XFS_IRECLAIMABLE
-		 * state. Wait for the initialisation to complete before
-		 * continuing.
-		 */
-		wait_on_inode(VFS_I(ip));
-	}
+		if (!igrab(inode)) {
+			error = EAGAIN;
+			goto out_error;
+		}
 
-	if (ip->i_d.di_mode == 0 && !(flags & XFS_IGET_CREATE)) {
-		error = ENOENT;
-		iput(VFS_I(ip));
-		goto out_error;
+		/* We've got a live one. */
+		spin_unlock(&ip->i_flags_lock);
+		read_unlock(&pag->pag_ici_lock);
 	}
 
-	/* We've got a live one. */
-	read_unlock(&pag->pag_ici_lock);
-
 	if (lock_flags != 0)
 		xfs_ilock(ip, lock_flags);
 
@@ -274,6 +276,7 @@ xfs_iget_cache_hit(
 	return 0;
 
 out_error:
+	spin_unlock(&ip->i_flags_lock);
 	read_unlock(&pag->pag_ici_lock);
 	return error;
 }
-- 
GitLab


From c7f6fa44115d401e89db730f357629d39f8e4ba6 Mon Sep 17 00:00:00 2001
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Tue, 28 Jul 2009 23:52:54 +0200
Subject: [PATCH 0918/1153] x86, mce: don't log boot MCEs on Pentium M (model
 == 13) CPUs

On my legacy Pentium M laptop (Acer Extensa 2900) I get bogus MCE on a cold
boot with CONFIG_X86_NEW_MCE enabled, i.e. (after decoding it with mcelog):

MCE 0
HARDWARE ERROR. This is *NOT* a software problem!
Please contact your hardware vendor
CPU 0 BANK 1 MCG status:
MCi status:
Error overflow
Uncorrected error
Error enabled
Processor context corrupt
MCA: Data CACHE Level-1 UNKNOWN Error
STATUS f200000000000195 MCGSTATUS 0

[ The other STATUS values observed: f2000000000001b5 (... UNKNOWN error)
  and f200000000000115 (... READ Error).

  To verify that this is not a CONFIG_X86_NEW_MCE bug I also modified
  the CONFIG_X86_OLD_MCE code (which doesn't log any MCEs) to dump
  content of STATUS MSR before it is cleared during initialization. ]

Since the bogus MCE results in a kernel taint (which in turn disables
lockdep support) don't log boot MCEs on Pentium M (model == 13) CPUs
by default ("mce=bootlog" boot parameter can be be used to get the old
behavior).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/cpu/mcheck/mce.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/x86/kernel/cpu/mcheck/mce.c b/arch/x86/kernel/cpu/mcheck/mce.c
index 1cfb623ce11..a0c2910d96a 100644
--- a/arch/x86/kernel/cpu/mcheck/mce.c
+++ b/arch/x86/kernel/cpu/mcheck/mce.c
@@ -1273,6 +1273,10 @@ static void mce_cpu_quirks(struct cpuinfo_x86 *c)
 		if ((c->x86 > 6 || (c->x86 == 6 && c->x86_model >= 0xe)) &&
 			monarch_timeout < 0)
 			monarch_timeout = USEC_PER_SEC;
+
+		/* There are also broken BIOSes on some Pentium M systems. */
+		if (c->x86 == 6 && c->x86_model == 13 && mce_bootlog < 0)
+			mce_bootlog = 0;
 	}
 	if (monarch_timeout < 0)
 		monarch_timeout = 0;
-- 
GitLab


From 2932cffc89e9a1476b28a59896fa4f81e0d4f131 Mon Sep 17 00:00:00 2001
From: "Carlos R. Mafra" <crmafra@gmail.com>
Date: Mon, 17 Aug 2009 00:36:21 +0200
Subject: [PATCH 0919/1153] perf: Rename perf-examples.txt to examples.txt

Rename it to examples.txt to avoid the perf-*.txt pattern in
the Makefile, otherwise 'make doc' fails because
perf-examples.txt is not formatted to be a man page:

 ERROR: perf-examples.txt: line 1: manpage document title is mandatory

Signed-off-by: Carlos R. Mafra <crmafra@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Documentation/{perf-examples.txt => examples.txt} | 0
 1 file changed, 0 insertions(+), 0 deletions(-)
 rename tools/perf/Documentation/{perf-examples.txt => examples.txt} (100%)

diff --git a/tools/perf/Documentation/perf-examples.txt b/tools/perf/Documentation/examples.txt
similarity index 100%
rename from tools/perf/Documentation/perf-examples.txt
rename to tools/perf/Documentation/examples.txt
-- 
GitLab


From e1ac3614ff606ae03677f47459113f98a19af63c Mon Sep 17 00:00:00 2001
From: Paul Mackerras <paulus@samba.org>
Date: Fri, 14 Aug 2009 15:39:10 +1000
Subject: [PATCH 0920/1153] perf_counter: Check task on counter read IPI

In general, code in perf_counter.c that is called through an
IPI checks, for per-task counters, that the counter's task is
still the current task.  This is to handle the race condition
where the cpu switches from the task we want to another task in
the interval between sending the IPI and the IPI arriving and
being handled on the target CPU.

For some reason, __perf_counter_read is missing this check, yet
there is no reason why the race condition can't occur.  This
adds a check that the current task is the one we want.  If it
isn't, we just return.  In that case the counter->count value
should be up to date, since it will have been updated when the
counter was scheduled out, which must have happened since the
IPI was sent.

I don't have an example of an actual failure due to this race,
but it seems obvious that it could occur and we need to guard
against it.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <19076.63614.277861.368125@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 534e20d14d6..b8fe7397b90 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -1503,10 +1503,21 @@ static void perf_counter_enable_on_exec(struct task_struct *task)
  */
 static void __perf_counter_read(void *info)
 {
+	struct perf_cpu_context *cpuctx = &__get_cpu_var(perf_cpu_context);
 	struct perf_counter *counter = info;
 	struct perf_counter_context *ctx = counter->ctx;
 	unsigned long flags;
 
+	/*
+	 * If this is a task context, we need to check whether it is
+	 * the current task context of this cpu.  If not it has been
+	 * scheduled out before the smp call arrived.  In that case
+	 * counter->count would have been updated to a recent sample
+	 * when the counter was scheduled out.
+	 */
+	if (ctx->task && cpuctx->task_ctx != ctx)
+		return;
+
 	local_irq_save(flags);
 	if (ctx->is_active)
 		update_context_time(ctx);
-- 
GitLab


From de809347aeef0a68c04576c464414d0e4dce59fc Mon Sep 17 00:00:00 2001
From: Amerigo Wang <amwang@redhat.com>
Date: Mon, 17 Aug 2009 05:43:01 -0400
Subject: [PATCH 0921/1153] timers: Drop write permission on /proc/timer_list

/proc/timer_list and /proc/slabinfo are not supposed to be
written, so there should be no write permissions on it.

Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: linux-mm@kvack.org
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
LKML-Reference: <20090817094525.6355.88682.sendpatchset@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/time/timer_list.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/time/timer_list.c b/kernel/time/timer_list.c
index a999b92a127..fddd69d16e0 100644
--- a/kernel/time/timer_list.c
+++ b/kernel/time/timer_list.c
@@ -286,7 +286,7 @@ static int __init init_timer_list_procfs(void)
 {
 	struct proc_dir_entry *pe;
 
-	pe = proc_create("timer_list", 0644, NULL, &timer_list_fops);
+	pe = proc_create("timer_list", 0444, NULL, &timer_list_fops);
 	if (!pe)
 		return -ENOMEM;
 	return 0;
-- 
GitLab


From e412cd257e0d51e0ecbb89f50953835b5a0681b2 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Mon, 17 Aug 2009 10:19:00 +0200
Subject: [PATCH 0922/1153] x86, mce: Don't initialize MCEs on unknown CPUs

An older test-box started hanging at the following point during
bootup:

 [    0.022996] Mount-cache hash table entries: 512
 [    0.024996] Initializing cgroup subsys debug
 [    0.025996] Initializing cgroup subsys cpuacct
 [    0.026995] Initializing cgroup subsys devices
 [    0.027995] Initializing cgroup subsys freezer
 [    0.028995] mce: CPU supports 5 MCE banks

I've bisected it down to commit 4efc0670 ("x86, mce: use 64bit
machine check code on 32bit"), which utilizes the MCE code on
32-bit systems too.

The problem is caused by this detail in my config:

  # CONFIG_CPU_SUP_INTEL is not set

This disables the quirks in mce_cpu_quirks() but still enables
MCE support - which then hangs due to the missing quirk
workaround needed on this CPU:

	if (c->x86 == 6 && c->x86_model < 0x1A && banks > 0)
		mce_banks[0].init = 0;

The safe solution is to not initialize MCEs if we dont know on
what CPU we are running (or if that CPU's support code got
disabled in the config).

Also be a bit more defensive on 32-bit systems: dont do a
boot-time dump of pending MCEs not just on the specific system
that we found a problem with (Pentium-M), but earlier ones as
well.

Now this problem is probably not common and disabling CPU
support is rare - but still being more defensive in something
we turned on for a wide range of CPUs is prudent.

Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
LKML-Reference: Message-ID: <4A88E3E4.40506@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/cpu/mcheck/mce.c | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)

diff --git a/arch/x86/kernel/cpu/mcheck/mce.c b/arch/x86/kernel/cpu/mcheck/mce.c
index a0c2910d96a..01213048f62 100644
--- a/arch/x86/kernel/cpu/mcheck/mce.c
+++ b/arch/x86/kernel/cpu/mcheck/mce.c
@@ -1226,8 +1226,13 @@ static void mce_init(void)
 }
 
 /* Add per CPU specific workarounds here */
-static void mce_cpu_quirks(struct cpuinfo_x86 *c)
+static int mce_cpu_quirks(struct cpuinfo_x86 *c)
 {
+	if (c->x86_vendor == X86_VENDOR_UNKNOWN) {
+		pr_info("MCE: unknown CPU type - not enabling MCE support.\n");
+		return -EOPNOTSUPP;
+	}
+
 	/* This should be disabled by the BIOS, but isn't always */
 	if (c->x86_vendor == X86_VENDOR_AMD) {
 		if (c->x86 == 15 && banks > 4) {
@@ -1274,14 +1279,19 @@ static void mce_cpu_quirks(struct cpuinfo_x86 *c)
 			monarch_timeout < 0)
 			monarch_timeout = USEC_PER_SEC;
 
-		/* There are also broken BIOSes on some Pentium M systems. */
-		if (c->x86 == 6 && c->x86_model == 13 && mce_bootlog < 0)
+		/*
+		 * There are also broken BIOSes on some Pentium M and
+		 * earlier systems:
+		 */
+		if (c->x86 == 6 && c->x86_model <= 13 && mce_bootlog < 0)
 			mce_bootlog = 0;
 	}
 	if (monarch_timeout < 0)
 		monarch_timeout = 0;
 	if (mce_bootlog != 0)
 		mce_panic_timeout = 30;
+
+	return 0;
 }
 
 static void __cpuinit mce_ancient_init(struct cpuinfo_x86 *c)
@@ -1342,11 +1352,10 @@ void __cpuinit mcheck_init(struct cpuinfo_x86 *c)
 	if (!mce_available(c))
 		return;
 
-	if (mce_cap_init() < 0) {
+	if (mce_cap_init() < 0 || mce_cpu_quirks(c) < 0) {
 		mce_disabled = 1;
 		return;
 	}
-	mce_cpu_quirks(c);
 
 	machine_check_vector = do_machine_check;
 
-- 
GitLab


From 87c62a66edd645a9b1ff1f9b00ab20c5a93d8845 Mon Sep 17 00:00:00 2001
From: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Date: Tue, 14 Jul 2009 22:37:09 +0900
Subject: [PATCH 0923/1153] MIPS: Fix HPAGE_SIZE redefinition

This patch fixes warnings like this:
  CC      fs/proc/meminfo.o
In file included from /work/linux/include/linux/mmzone.h:20,
                 from /work/linux/include/linux/gfp.h:4,
                 from /work/linux/include/linux/mm.h:8,
                 from /work/linux/fs/proc/meminfo.c:5:
/work/linux/arch/mips/include/asm/page.h:36:1: warning: "HPAGE_SIZE" redefined
In file included from /work/linux/fs/proc/meminfo.c:2:
/work/linux/include/linux/hugetlb.h:107:1: warning: this is the location of the previous definition

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
 arch/mips/include/asm/page.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/mips/include/asm/page.h b/arch/mips/include/asm/page.h
index 96a14a426a7..4320239cf4e 100644
--- a/arch/mips/include/asm/page.h
+++ b/arch/mips/include/asm/page.h
@@ -32,10 +32,12 @@
 #define PAGE_SIZE	(1UL << PAGE_SHIFT)
 #define PAGE_MASK       (~((1 << PAGE_SHIFT) - 1))
 
+#ifdef CONFIG_HUGETLB_PAGE
 #define HPAGE_SHIFT	(PAGE_SHIFT + PAGE_SHIFT - 3)
 #define HPAGE_SIZE	((1UL) << HPAGE_SHIFT)
 #define HPAGE_MASK	(~(HPAGE_SIZE - 1))
 #define HUGETLB_PAGE_ORDER	(HPAGE_SHIFT - PAGE_SHIFT)
+#endif /* CONFIG_HUGETLB_PAGE */
 
 #ifndef __ASSEMBLY__
 
-- 
GitLab


From 523d2f6982136d332c9b7dd00e9e16da1091f060 Mon Sep 17 00:00:00 2001
From: Johannes Berg <johannes@sipsolutions.net>
Date: Wed, 1 Jul 2009 21:26:43 +0200
Subject: [PATCH 0924/1153] mac80211: fix todo lock

The key todo lock can be taken from different locks
that require it to be _bh to avoid lock inversion
due to (soft)irqs.

This should fix the two problems reported by Bob and
Gabor:
http://mid.gmane.org/20090619113049.GB18956@hash.localnet
http://mid.gmane.org/4A3FA376.8020307@openwrt.org

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 net/mac80211/key.c | 28 +++++++++++++++-------------
 1 file changed, 15 insertions(+), 13 deletions(-)

diff --git a/net/mac80211/key.c b/net/mac80211/key.c
index ce267565e18..659a42d529e 100644
--- a/net/mac80211/key.c
+++ b/net/mac80211/key.c
@@ -67,6 +67,8 @@ static DECLARE_WORK(todo_work, key_todo);
  *
  * @key: key to add to do item for
  * @flag: todo flag(s)
+ *
+ * Must be called with IRQs or softirqs disabled.
  */
 static void add_todo(struct ieee80211_key *key, u32 flag)
 {
@@ -140,9 +142,9 @@ static void ieee80211_key_enable_hw_accel(struct ieee80211_key *key)
 	ret = drv_set_key(key->local, SET_KEY, &sdata->vif, sta, &key->conf);
 
 	if (!ret) {
-		spin_lock(&todo_lock);
+		spin_lock_bh(&todo_lock);
 		key->flags |= KEY_FLAG_UPLOADED_TO_HARDWARE;
-		spin_unlock(&todo_lock);
+		spin_unlock_bh(&todo_lock);
 	}
 
 	if (ret && ret != -ENOSPC && ret != -EOPNOTSUPP)
@@ -164,12 +166,12 @@ static void ieee80211_key_disable_hw_accel(struct ieee80211_key *key)
 	if (!key || !key->local->ops->set_key)
 		return;
 
-	spin_lock(&todo_lock);
+	spin_lock_bh(&todo_lock);
 	if (!(key->flags & KEY_FLAG_UPLOADED_TO_HARDWARE)) {
-		spin_unlock(&todo_lock);
+		spin_unlock_bh(&todo_lock);
 		return;
 	}
-	spin_unlock(&todo_lock);
+	spin_unlock_bh(&todo_lock);
 
 	sta = get_sta_for_key(key);
 	sdata = key->sdata;
@@ -188,9 +190,9 @@ static void ieee80211_key_disable_hw_accel(struct ieee80211_key *key)
 		       wiphy_name(key->local->hw.wiphy),
 		       key->conf.keyidx, sta ? sta->addr : bcast_addr, ret);
 
-	spin_lock(&todo_lock);
+	spin_lock_bh(&todo_lock);
 	key->flags &= ~KEY_FLAG_UPLOADED_TO_HARDWARE;
-	spin_unlock(&todo_lock);
+	spin_unlock_bh(&todo_lock);
 }
 
 static void __ieee80211_set_default_key(struct ieee80211_sub_if_data *sdata,
@@ -437,14 +439,14 @@ void ieee80211_key_link(struct ieee80211_key *key,
 
 	__ieee80211_key_replace(sdata, sta, old_key, key);
 
-	spin_unlock_irqrestore(&sdata->local->key_lock, flags);
-
 	/* free old key later */
 	add_todo(old_key, KEY_FLAG_TODO_DELETE);
 
 	add_todo(key, KEY_FLAG_TODO_ADD_DEBUGFS);
 	if (netif_running(sdata->dev))
 		add_todo(key, KEY_FLAG_TODO_HWACCEL_ADD);
+
+	spin_unlock_irqrestore(&sdata->local->key_lock, flags);
 }
 
 static void __ieee80211_key_free(struct ieee80211_key *key)
@@ -547,7 +549,7 @@ static void __ieee80211_key_todo(void)
 	 */
 	synchronize_rcu();
 
-	spin_lock(&todo_lock);
+	spin_lock_bh(&todo_lock);
 	while (!list_empty(&todo_list)) {
 		key = list_first_entry(&todo_list, struct ieee80211_key, todo);
 		list_del_init(&key->todo);
@@ -558,7 +560,7 @@ static void __ieee80211_key_todo(void)
 					  KEY_FLAG_TODO_HWACCEL_REMOVE |
 					  KEY_FLAG_TODO_DELETE);
 		key->flags &= ~todoflags;
-		spin_unlock(&todo_lock);
+		spin_unlock_bh(&todo_lock);
 
 		work_done = false;
 
@@ -591,9 +593,9 @@ static void __ieee80211_key_todo(void)
 
 		WARN_ON(!work_done);
 
-		spin_lock(&todo_lock);
+		spin_lock_bh(&todo_lock);
 	}
-	spin_unlock(&todo_lock);
+	spin_unlock_bh(&todo_lock);
 }
 
 void ieee80211_key_todo(void)
-- 
GitLab


From 518ff04fd84290a7ad9042e8a46d78d29cb443d3 Mon Sep 17 00:00:00 2001
From: "John W. Linville" <linville@tuxdriver.com>
Date: Mon, 17 Aug 2009 12:09:26 -0400
Subject: [PATCH 0925/1153] orinoco: correct key bounds check in
 orinoco_hw_get_tkip_iv

If key is 4 that is an array out of bounds.

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/orinoco/hw.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/orinoco/hw.c b/drivers/net/wireless/orinoco/hw.c
index 632fac86a30..b3946272c72 100644
--- a/drivers/net/wireless/orinoco/hw.c
+++ b/drivers/net/wireless/orinoco/hw.c
@@ -70,7 +70,7 @@ int orinoco_hw_get_tkip_iv(struct orinoco_private *priv, int key, u8 *tsc)
 	int err = 0;
 	u8 tsc_arr[4][IW_ENCODE_SEQ_MAX_SIZE];
 
-	if ((key < 0) || (key > 4))
+	if ((key < 0) || (key >= 4))
 		return -EINVAL;
 
 	err = hermes_read_ltv(hw, USER_BAP, HERMES_RID_CURRENT_TKIP_IV,
-- 
GitLab


From ada508274b8698a33cb0e5bd037db0f9dc781795 Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Mon, 3 Aug 2009 18:24:21 +0200
Subject: [PATCH 0926/1153] ocfs2: Handle quota file corruption more gracefully

ocfs2_read_virt_blocks() does BUG when we try to read a block from a file
beyond its end. Since this can happen due to filesystem corruption, it
is not really an appropriate answer. Make ocfs2_read_quota_block() check
the condition and handle it by calling ocfs2_error() and returning EIO.

[ Modified to print ip_blkno in the error - Joel ]

Reported-by: Tristan Ye <tristan.ye@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/quota_global.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/fs/ocfs2/quota_global.c b/fs/ocfs2/quota_global.c
index bf7742d0ee3..44f2a5e1d04 100644
--- a/fs/ocfs2/quota_global.c
+++ b/fs/ocfs2/quota_global.c
@@ -23,6 +23,7 @@
 #include "sysfile.h"
 #include "dlmglue.h"
 #include "uptodate.h"
+#include "super.h"
 #include "quota.h"
 
 static struct workqueue_struct *ocfs2_quota_wq = NULL;
@@ -114,6 +115,15 @@ int ocfs2_read_quota_block(struct inode *inode, u64 v_block,
 	int rc = 0;
 	struct buffer_head *tmp = *bh;
 
+	if (i_size_read(inode) >> inode->i_sb->s_blocksize_bits <= v_block) {
+		ocfs2_error(inode->i_sb,
+			    "Quota file %llu is probably corrupted! Requested "
+			    "to read block %Lu but file has size only %Lu\n",
+			    (unsigned long long)OCFS2_I(inode)->ip_blkno,
+			    (unsigned long long)v_block,
+			    (unsigned long long)i_size_read(inode));
+		return -EIO;
+	}
 	rc = ocfs2_read_virt_blocks(inode, v_block, 1, &tmp, 0,
 				    ocfs2_validate_quota_block);
 	if (rc)
-- 
GitLab


From 60e2ec48665b8495360ca4a6004c5cd52beb2bc1 Mon Sep 17 00:00:00 2001
From: Tao Ma <tao.ma@oracle.com>
Date: Wed, 12 Aug 2009 14:42:47 +0800
Subject: [PATCH 0927/1153] ocfs2: release the buffer head in
 ocfs2_do_truncate.

In ocfs2_do_truncate, we forget to release last_eb_bh which
will cause memleak. So call brelse in the end.

Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/alloc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/ocfs2/alloc.c b/fs/ocfs2/alloc.c
index f9a3e894266..ab513ddaeff 100644
--- a/fs/ocfs2/alloc.c
+++ b/fs/ocfs2/alloc.c
@@ -6851,7 +6851,7 @@ static int ocfs2_do_truncate(struct ocfs2_super *osb,
 	}
 	status = 0;
 bail:
-
+	brelse(last_eb_bh);
 	mlog_exit(status);
 	return status;
 }
-- 
GitLab


From eef3a116be11d35396efb2a8cc7345fd3221e294 Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Sun, 16 Aug 2009 21:51:44 -0400
Subject: [PATCH 0928/1153] notify: unused event private race

inotify decides if private data it passed to get added to an event was
used by checking list_empty().  But it's possible that the event may
have been dequeued and the private event removed so it would look empty.

The fix is to use the return code from fsnotify_add_notify_event rather
than looking at the list.

Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/notify/inotify/inotify_fsnotify.c | 13 +++++++------
 fs/notify/inotify/inotify_user.c     |  7 +++----
 fs/notify/notification.c             |  7 +++----
 3 files changed, 13 insertions(+), 14 deletions(-)

diff --git a/fs/notify/inotify/inotify_fsnotify.c b/fs/notify/inotify/inotify_fsnotify.c
index 47cd258fd24..5dcbafe72d7 100644
--- a/fs/notify/inotify/inotify_fsnotify.c
+++ b/fs/notify/inotify/inotify_fsnotify.c
@@ -62,13 +62,14 @@ static int inotify_handle_event(struct fsnotify_group *group, struct fsnotify_ev
 	event_priv->wd = wd;
 
 	ret = fsnotify_add_notify_event(group, event, fsn_event_priv);
-	/* EEXIST is not an error */
-	if (ret == -EEXIST)
-		ret = 0;
-
-	/* did event_priv get attached? */
-	if (list_empty(&fsn_event_priv->event_list))
+	if (ret) {
 		inotify_free_event_priv(fsn_event_priv);
+		/* EEXIST says we tail matched, EOVERFLOW isn't something
+		 * to report up the stack. */
+		if ((ret == -EEXIST) ||
+		    (ret == -EOVERFLOW))
+			ret = 0;
+	}
 
 	/*
 	 * If we hold the entry until after the event is on the queue
diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c
index f30d9bbc2e1..c172a7a17b1 100644
--- a/fs/notify/inotify/inotify_user.c
+++ b/fs/notify/inotify/inotify_user.c
@@ -386,6 +386,7 @@ void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry,
 	struct fsnotify_event *ignored_event;
 	struct inotify_event_private_data *event_priv;
 	struct fsnotify_event_private_data *fsn_event_priv;
+	int ret;
 
 	ignored_event = fsnotify_create_event(NULL, FS_IN_IGNORED, NULL,
 					      FSNOTIFY_EVENT_NONE, NULL, 0,
@@ -404,10 +405,8 @@ void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry,
 	fsn_event_priv->group = group;
 	event_priv->wd = ientry->wd;
 
-	fsnotify_add_notify_event(group, ignored_event, fsn_event_priv);
-
-	/* did the private data get added? */
-	if (list_empty(&fsn_event_priv->event_list))
+	ret = fsnotify_add_notify_event(group, ignored_event, fsn_event_priv);
+	if (ret)
 		inotify_free_event_priv(fsn_event_priv);
 
 skip_send_ignore:
diff --git a/fs/notify/notification.c b/fs/notify/notification.c
index 521368574e9..74b3cf30bc6 100644
--- a/fs/notify/notification.c
+++ b/fs/notify/notification.c
@@ -171,9 +171,7 @@ int fsnotify_add_notify_event(struct fsnotify_group *group, struct fsnotify_even
 	struct list_head *list = &group->notification_list;
 	struct fsnotify_event_holder *last_holder;
 	struct fsnotify_event *last_event;
-
-	/* easy to tell if priv was attached to the event */
-	INIT_LIST_HEAD(&priv->event_list);
+	int ret = 0;
 
 	/*
 	 * There is one fsnotify_event_holder embedded inside each fsnotify_event.
@@ -194,6 +192,7 @@ alloc_holder:
 
 	if (group->q_len >= group->max_events) {
 		event = &q_overflow_event;
+		ret = -EOVERFLOW;
 		/* sorry, no private data on the overflow event */
 		priv = NULL;
 	}
@@ -235,7 +234,7 @@ alloc_holder:
 	mutex_unlock(&group->notification_mutex);
 
 	wake_up(&group->notification_waitq);
-	return 0;
+	return ret;
 }
 
 /*
-- 
GitLab


From cd94c8bbef8d4b796a7ed4c551355a334604fd36 Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Sun, 16 Aug 2009 21:51:49 -0400
Subject: [PATCH 0929/1153] inotify: tail drop inotify q_overflow events

In f44aebcc the tail drop logic of events with no file backing
(q_overflow and in_ignored) was reversed so IN_IGNORED events would
never be tail dropped.  This now means that Q_OVERFLOW events are NOT
tail dropped.  The fix is to not tail drop IN_IGNORED, but to tail drop
Q_OVERFLOW.

Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/notify/notification.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/fs/notify/notification.c b/fs/notify/notification.c
index 74b3cf30bc6..3816d5750dd 100644
--- a/fs/notify/notification.c
+++ b/fs/notify/notification.c
@@ -153,6 +153,10 @@ static bool event_compare(struct fsnotify_event *old, struct fsnotify_event *new
 				return true;
 			break;
 		case (FSNOTIFY_EVENT_NONE):
+			if (old->mask & FS_Q_OVERFLOW)
+				return true;
+			else if (old->mask & FS_IN_IGNORED)
+				return false;
 			return false;
 		};
 	}
-- 
GitLab


From 08e53fcb0db34baca3db84a457b6d67faabee4c6 Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Sun, 16 Aug 2009 21:51:55 -0400
Subject: [PATCH 0930/1153] inotify: start watch descriptor count at 1

The inotify_add_watch man page specifies that inotify_add_watch() will
return a non-negative integer.  However, historically the inotify
watches started at 1, not at 0.

Turns out that the inotifywait program provided by the inotify-tools
package doesn't properly handle a 0 watch descriptor.  In 7e790dd5 we
changed from starting at 1 to starting at 0.  This patch starts at 1,
just like in previous kernels, but also just like in previous kernels
it's possible for it to wrap back to 0.  This preserves the kernel
functionality exactly like it was before the patch (neither method broke
the spec)

Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/notify/inotify/inotify_user.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c
index c172a7a17b1..dc32ed8323b 100644
--- a/fs/notify/inotify/inotify_user.c
+++ b/fs/notify/inotify/inotify_user.c
@@ -567,7 +567,7 @@ static struct fsnotify_group *inotify_new_group(struct user_struct *user, unsign
 
 	spin_lock_init(&group->inotify_data.idr_lock);
 	idr_init(&group->inotify_data.idr);
-	group->inotify_data.last_wd = 0;
+	group->inotify_data.last_wd = 1;
 	group->inotify_data.user = user;
 	group->inotify_data.fa = NULL;
 
-- 
GitLab


From 1adcaafe7414c5731f758b158aa0525057225deb Mon Sep 17 00:00:00 2001
From: Suresh Siddha <suresh.b.siddha@intel.com>
Date: Mon, 17 Aug 2009 13:23:50 -0700
Subject: [PATCH 0931/1153] x86, pat: Allow ISA memory range uncacheable
 mapping requests

Max Vozeler reported:
>  Bug 13877 -  bogl-term broken with CONFIG_X86_PAT=y, works with =n
>
>  strace of bogl-term:
>  814   mmap2(NULL, 65536, PROT_READ|PROT_WRITE, MAP_SHARED, 4, 0)
>				 = -1 EAGAIN (Resource temporarily unavailable)
>  814   write(2, "bogl: mmaping /dev/fb0: Resource temporarily unavailable\n",
>	       57) = 57

PAT code maps the ISA memory range as WB in the PAT attribute, so that
fixed range MTRR registers define the actual memory type (UC/WC/WT etc).

But the upper level is_new_memtype_allowed() API checks are failing,
as the request here is for UC and the return tracked type is WB (Tracked type is
WB as MTRR type for this legacy range potentially will be different for each
4k page).

Fix is_new_memtype_allowed() by always succeeding the ISA address range
checks, as the null PAT (WB) and def MTRR fixed range register settings
satisfy the memory type needs of the applications that map the ISA address
range.

Reported-and-Tested-by: Max Vozeler <xam@debian.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
---
 arch/x86/include/asm/pgtable.h | 12 ++++++++++--
 arch/x86/mm/pat.c              |  3 ++-
 2 files changed, 12 insertions(+), 3 deletions(-)

diff --git a/arch/x86/include/asm/pgtable.h b/arch/x86/include/asm/pgtable.h
index 3cc06e3fceb..16748077559 100644
--- a/arch/x86/include/asm/pgtable.h
+++ b/arch/x86/include/asm/pgtable.h
@@ -2,6 +2,7 @@
 #define _ASM_X86_PGTABLE_H
 
 #include <asm/page.h>
+#include <asm/e820.h>
 
 #include <asm/pgtable_types.h>
 
@@ -269,9 +270,16 @@ static inline pgprot_t pgprot_modify(pgprot_t oldprot, pgprot_t newprot)
 
 #define canon_pgprot(p) __pgprot(massage_pgprot(p))
 
-static inline int is_new_memtype_allowed(unsigned long flags,
-						unsigned long new_flags)
+static inline int is_new_memtype_allowed(u64 paddr, unsigned long size,
+					 unsigned long flags,
+					 unsigned long new_flags)
 {
+	/*
+	 * PAT type is always WB for ISA. So no need to check.
+	 */
+	if (is_ISA_range(paddr, paddr + size - 1))
+		return 1;
+
 	/*
 	 * Certain new memtypes are not allowed with certain
 	 * requested memtype:
diff --git a/arch/x86/mm/pat.c b/arch/x86/mm/pat.c
index e6718bb2806..352aa9e927e 100644
--- a/arch/x86/mm/pat.c
+++ b/arch/x86/mm/pat.c
@@ -623,7 +623,8 @@ static int reserve_pfn_range(u64 paddr, unsigned long size, pgprot_t *vma_prot,
 		return ret;
 
 	if (flags != want_flags) {
-		if (strict_prot || !is_new_memtype_allowed(want_flags, flags)) {
+		if (strict_prot ||
+		    !is_new_memtype_allowed(paddr, size, want_flags, flags)) {
 			free_memtype(paddr, paddr + size);
 			printk(KERN_ERR "%s:%d map pfn expected mapping type %s"
 				" for %Lx-%Lx, got %s\n",
-- 
GitLab


From 50fb6d2bd7062708892ae7147f30c3ee905b7a3d Mon Sep 17 00:00:00 2001
From: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Date: Sun, 19 Jul 2009 13:41:57 -0600
Subject: [PATCH 0932/1153] 9p: Check for error in return value of v9fs_fid_add

Check if v9fs_fid_add was successful or not based on its
return value.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 fs/9p/vfs_inode.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c
index 81f8bbf12f9..1fa5f15eadd 100644
--- a/fs/9p/vfs_inode.c
+++ b/fs/9p/vfs_inode.c
@@ -470,7 +470,10 @@ v9fs_create(struct v9fs_session_info *v9ses, struct inode *dir,
 		dentry->d_op = &v9fs_dentry_operations;
 
 	d_instantiate(dentry, inode);
-	v9fs_fid_add(dentry, fid);
+	err = v9fs_fid_add(dentry, fid);
+	if (err < 0)
+		goto error;
+
 	return ofid;
 
 error:
-- 
GitLab


From 2bb541157fe2602af7b9952096d0524f6f9c1e73 Mon Sep 17 00:00:00 2001
From: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Date: Sun, 19 Jul 2009 13:41:56 -0600
Subject: [PATCH 0933/1153] 9p: Fix possible inode leak in v9fs_get_inode.

Add a missing iput when cleaning up if v9fs_get_inode
fails after returning a valid inode.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 fs/9p/vfs_inode.c | 105 ++++++++++++++++++++++++----------------------
 1 file changed, 56 insertions(+), 49 deletions(-)

diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c
index 1fa5f15eadd..0c8af1abf60 100644
--- a/fs/9p/vfs_inode.c
+++ b/fs/9p/vfs_inode.c
@@ -207,65 +207,72 @@ v9fs_blank_wstat(struct p9_wstat *wstat)
 
 struct inode *v9fs_get_inode(struct super_block *sb, int mode)
 {
+	int err;
 	struct inode *inode;
 	struct v9fs_session_info *v9ses = sb->s_fs_info;
 
 	P9_DPRINTK(P9_DEBUG_VFS, "super block: %p mode: %o\n", sb, mode);
 
 	inode = new_inode(sb);
-	if (inode) {
-		inode->i_mode = mode;
-		inode->i_uid = current_fsuid();
-		inode->i_gid = current_fsgid();
-		inode->i_blocks = 0;
-		inode->i_rdev = 0;
-		inode->i_atime = inode->i_mtime = inode->i_ctime = CURRENT_TIME;
-		inode->i_mapping->a_ops = &v9fs_addr_operations;
-
-		switch (mode & S_IFMT) {
-		case S_IFIFO:
-		case S_IFBLK:
-		case S_IFCHR:
-		case S_IFSOCK:
-			if (!v9fs_extended(v9ses)) {
-				P9_DPRINTK(P9_DEBUG_ERROR,
-				      "special files without extended mode\n");
-				return ERR_PTR(-EINVAL);
-			}
-			init_special_inode(inode, inode->i_mode,
-					   inode->i_rdev);
-			break;
-		case S_IFREG:
-			inode->i_op = &v9fs_file_inode_operations;
-			inode->i_fop = &v9fs_file_operations;
-			break;
-		case S_IFLNK:
-			if (!v9fs_extended(v9ses)) {
-				P9_DPRINTK(P9_DEBUG_ERROR,
-					"extended modes used w/o 9P2000.u\n");
-				return ERR_PTR(-EINVAL);
-			}
-			inode->i_op = &v9fs_symlink_inode_operations;
-			break;
-		case S_IFDIR:
-			inc_nlink(inode);
-			if (v9fs_extended(v9ses))
-				inode->i_op = &v9fs_dir_inode_operations_ext;
-			else
-				inode->i_op = &v9fs_dir_inode_operations;
-			inode->i_fop = &v9fs_dir_operations;
-			break;
-		default:
+	if (!inode) {
+		P9_EPRINTK(KERN_WARNING, "Problem allocating inode\n");
+		return -ENOMEM;
+	}
+
+	inode->i_mode = mode;
+	inode->i_uid = current_fsuid();
+	inode->i_gid = current_fsgid();
+	inode->i_blocks = 0;
+	inode->i_rdev = 0;
+	inode->i_atime = inode->i_mtime = inode->i_ctime = CURRENT_TIME;
+	inode->i_mapping->a_ops = &v9fs_addr_operations;
+
+	switch (mode & S_IFMT) {
+	case S_IFIFO:
+	case S_IFBLK:
+	case S_IFCHR:
+	case S_IFSOCK:
+		if (!v9fs_extended(v9ses)) {
 			P9_DPRINTK(P9_DEBUG_ERROR,
-				"BAD mode 0x%x S_IFMT 0x%x\n",
-				mode, mode & S_IFMT);
-			return ERR_PTR(-EINVAL);
+				   "special files without extended mode\n");
+			err = -EINVAL;
+			goto error;
 		}
-	} else {
-		P9_EPRINTK(KERN_WARNING, "Problem allocating inode\n");
-		return ERR_PTR(-ENOMEM);
+		init_special_inode(inode, inode->i_mode, inode->i_rdev);
+		break;
+	case S_IFREG:
+		inode->i_op = &v9fs_file_inode_operations;
+		inode->i_fop = &v9fs_file_operations;
+		break;
+	case S_IFLNK:
+		if (!v9fs_extended(v9ses)) {
+			P9_DPRINTK(P9_DEBUG_ERROR,
+				   "extended modes used w/o 9P2000.u\n");
+			err = -EINVAL;
+			goto error;
+		}
+		inode->i_op = &v9fs_symlink_inode_operations;
+		break;
+	case S_IFDIR:
+		inc_nlink(inode);
+		if (v9fs_extended(v9ses))
+			inode->i_op = &v9fs_dir_inode_operations_ext;
+		else
+			inode->i_op = &v9fs_dir_inode_operations;
+		inode->i_fop = &v9fs_dir_operations;
+		break;
+	default:
+		P9_DPRINTK(P9_DEBUG_ERROR, "BAD mode 0x%x S_IFMT 0x%x\n",
+			   mode, mode & S_IFMT);
+		err = -EINVAL;
+		goto error;
 	}
+
 	return inode;
+
+error:
+	iput(inode);
+	return ERR_PTR(err);
 }
 
 /*
-- 
GitLab


From 0e15597ebfe00e28857185f46aba00f400480ffe Mon Sep 17 00:00:00 2001
From: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Date: Sun, 19 Jul 2009 13:41:55 -0600
Subject: [PATCH 0934/1153] 9p: minor comment fixes

Fix the comments -- mostly the improper and/or missing descriptions
of function parameters.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 fs/9p/vfs_inode.c     |  3 +--
 net/9p/client.c       | 14 +++++++-------
 net/9p/trans_fd.c     |  8 ++++----
 net/9p/trans_rdma.c   |  9 +++++----
 net/9p/trans_virtio.c | 11 ++++-------
 5 files changed, 21 insertions(+), 24 deletions(-)

diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c
index 0c8af1abf60..f22668afd0d 100644
--- a/fs/9p/vfs_inode.c
+++ b/fs/9p/vfs_inode.c
@@ -171,7 +171,6 @@ int v9fs_uflags2omode(int uflags, int extended)
 
 /**
  * v9fs_blank_wstat - helper function to setup a 9P stat structure
- * @v9ses: 9P session info (for determining extended mode)
  * @wstat: structure to initialize
  *
  */
@@ -410,9 +409,9 @@ v9fs_open_created(struct inode *inode, struct file *file)
  * @v9ses: session information
  * @dir: directory that dentry is being created in
  * @dentry:  dentry that is being created
+ * @extension: 9p2000.u extension string to support devices, etc.
  * @perm: create permissions
  * @mode: open mode
- * @extension: 9p2000.u extension string to support devices, etc.
  *
  */
 static struct p9_fid *
diff --git a/net/9p/client.c b/net/9p/client.c
index 787ccddb85e..7bbd2d5ae8d 100644
--- a/net/9p/client.c
+++ b/net/9p/client.c
@@ -60,9 +60,9 @@ static struct p9_req_t *
 p9_client_rpc(struct p9_client *c, int8_t type, const char *fmt, ...);
 
 /**
- * v9fs_parse_options - parse mount options into session structure
- * @options: options string passed from mount
- * @v9ses: existing v9fs session information
+ * parse_options - parse mount options into client structure
+ * @opts: options string passed from mount
+ * @clnt: existing v9fs client information
  *
  * Return 0 upon success, -ERRNO upon failure
  */
@@ -232,7 +232,7 @@ EXPORT_SYMBOL(p9_tag_lookup);
 
 /**
  * p9_tag_init - setup tags structure and contents
- * @tags: tags structure from the client struct
+ * @c:  v9fs client struct
  *
  * This initializes the tags structure for each client instance.
  *
@@ -258,7 +258,7 @@ error:
 
 /**
  * p9_tag_cleanup - cleans up tags structure and reclaims resources
- * @tags: tags structure from the client struct
+ * @c:  v9fs client struct
  *
  * This frees resources associated with the tags structure
  *
@@ -430,8 +430,8 @@ static int p9_check_errors(struct p9_client *c, struct p9_req_t *req)
 
 /**
  * p9_client_flush - flush (cancel) a request
- * c: client state
- * req: request to cancel
+ * @c: client state
+ * @oldreq: request to cancel
  *
  * This sents a flush for a particular requests and links
  * the flush request to the original request.  The current
diff --git a/net/9p/trans_fd.c b/net/9p/trans_fd.c
index 8c2588e4edc..8d934dd7fd5 100644
--- a/net/9p/trans_fd.c
+++ b/net/9p/trans_fd.c
@@ -119,8 +119,8 @@ struct p9_poll_wait {
  * @wpos: write position for current frame
  * @wsize: amount of data to write for current frame
  * @wbuf: current write buffer
+ * @poll_pending_link: pending links to be polled per conn
  * @poll_wait: array of wait_q's for various worker threads
- * @poll_waddr: ????
  * @pt: poll state
  * @rq: current read work
  * @wq: current write work
@@ -700,9 +700,9 @@ static int p9_fd_cancel(struct p9_client *client, struct p9_req_t *req)
 }
 
 /**
- * parse_options - parse mount options into session structure
- * @options: options string passed from mount
- * @opts: transport-specific structure to parse options into
+ * parse_opts - parse mount options into p9_fd_opts structure
+ * @params: options string passed from mount
+ * @opts: fd transport-specific structure to parse options into
  *
  * Returns 0 upon success, -ERRNO upon failure
  */
diff --git a/net/9p/trans_rdma.c b/net/9p/trans_rdma.c
index ac4990041eb..65cb29db03f 100644
--- a/net/9p/trans_rdma.c
+++ b/net/9p/trans_rdma.c
@@ -67,14 +67,15 @@
  * @pd: Protection Domain pointer
  * @qp: Queue Pair pointer
  * @cq: Completion Queue pointer
+ * @dm_mr: DMA Memory Region pointer
  * @lkey: The local access only memory region key
  * @timeout: Number of uSecs to wait for connection management events
  * @sq_depth: The depth of the Send Queue
  * @sq_sem: Semaphore for the SQ
  * @rq_depth: The depth of the Receive Queue.
+ * @rq_count: Count of requests in the Receive Queue.
  * @addr: The remote peer's address
  * @req_lock: Protects the active request list
- * @send_wait: Wait list when the SQ fills up
  * @cm_done: Completion event for connection management tracking
  */
 struct p9_trans_rdma {
@@ -154,9 +155,9 @@ static match_table_t tokens = {
 };
 
 /**
- * parse_options - parse mount options into session structure
- * @options: options string passed from mount
- * @opts: transport-specific structure to parse options into
+ * parse_opts - parse mount options into rdma options structure
+ * @params: options string passed from mount
+ * @opts: rdma transport-specific structure to parse options into
  *
  * Returns 0 upon success, -ERRNO upon failure
  */
diff --git a/net/9p/trans_virtio.c b/net/9p/trans_virtio.c
index a49484e67e1..9bf0b737aa5 100644
--- a/net/9p/trans_virtio.c
+++ b/net/9p/trans_virtio.c
@@ -57,11 +57,9 @@ static int chan_index;
  * @initialized: whether the channel is initialized
  * @inuse: whether the channel is in use
  * @lock: protects multiple elements within this structure
+ * @client: client instance
  * @vdev: virtio dev associated with this channel
  * @vq: virtio queue associated with this channel
- * @tagpool: accounting for tag ids (and request slots)
- * @reqs: array of request slots
- * @max_tag: current number of request_slots allocated
  * @sg: scatter gather list which is used to pack a request (protected?)
  *
  * We keep all per-channel information in a structure.
@@ -92,7 +90,7 @@ static unsigned int rest_of_page(void *data)
 
 /**
  * p9_virtio_close - reclaim resources of a channel
- * @trans: transport state
+ * @client: client instance
  *
  * This reclaims a channel by freeing its resources and
  * reseting its inuse flag.
@@ -181,9 +179,8 @@ static int p9_virtio_cancel(struct p9_client *client, struct p9_req_t *req)
 
 /**
  * p9_virtio_request - issue a request
- * @t: transport state
- * @tc: &p9_fcall request to transmit
- * @rc: &p9_fcall to put reponse into
+ * @client: client instance issuing the request
+ * @req: request to be issued
  *
  */
 
-- 
GitLab


From 02bc35672b2fdf251e264adca5407792f63191e4 Mon Sep 17 00:00:00 2001
From: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Date: Sun, 19 Jul 2009 13:41:54 -0600
Subject: [PATCH 0935/1153] 9p: Fix possible memleak in v9fs_inode_from fid.

Add missing p9stat_free in v9fs_inode_from_fid to avoid
any possible leaks.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 fs/9p/vfs_inode.c | 13 ++++---------
 1 file changed, 4 insertions(+), 9 deletions(-)

diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c
index f22668afd0d..fac30d21851 100644
--- a/fs/9p/vfs_inode.c
+++ b/fs/9p/vfs_inode.c
@@ -344,30 +344,25 @@ v9fs_inode_from_fid(struct v9fs_session_info *v9ses, struct p9_fid *fid,
 
 	ret = NULL;
 	st = p9_client_stat(fid);
-	if (IS_ERR(st)) {
-		err = PTR_ERR(st);
-		st = NULL;
-		goto error;
-	}
+	if (IS_ERR(st))
+		return ERR_CAST(st);
 
 	umode = p9mode2unixmode(v9ses, st->mode);
 	ret = v9fs_get_inode(sb, umode);
 	if (IS_ERR(ret)) {
 		err = PTR_ERR(ret);
-		ret = NULL;
 		goto error;
 	}
 
 	v9fs_stat2inode(st, ret, sb);
 	ret->i_ino = v9fs_qid2ino(&st->qid);
+	p9stat_free(st);
 	kfree(st);
 	return ret;
 
 error:
+	p9stat_free(st);
 	kfree(st);
-	if (ret)
-		iput(ret);
-
 	return ERR_PTR(err);
 }
 
-- 
GitLab


From 4f4038328da5eb9cc237b51d3fe68138fd3fea14 Mon Sep 17 00:00:00 2001
From: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Date: Sun, 19 Jul 2009 13:41:53 -0600
Subject: [PATCH 0936/1153] 9p: Fix v9fs show_options

Add the delimiter ',' before the options when they are passed
and check if no option parameters are passed to prevent displaying
NULL in /proc/mounts.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 fs/9p/vfs_super.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/fs/9p/vfs_super.c b/fs/9p/vfs_super.c
index 38d695d66a0..a9d7d08cfbe 100644
--- a/fs/9p/vfs_super.c
+++ b/fs/9p/vfs_super.c
@@ -220,8 +220,8 @@ static void v9fs_kill_super(struct super_block *s)
 static int v9fs_show_options(struct seq_file *m, struct vfsmount *mnt)
 {
 	struct v9fs_session_info *v9ses = mnt->mnt_sb->s_fs_info;
-
-	seq_printf(m, "%s", v9ses->options);
+	if (v9ses->options != NULL)
+		seq_printf(m, ",%s", v9ses->options);
 	return 0;
 }
 
-- 
GitLab


From 1b5ab3e86712b6be38ebbe0d821387c1d8f91d7c Mon Sep 17 00:00:00 2001
From: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Date: Sun, 19 Jul 2009 13:41:52 -0600
Subject: [PATCH 0937/1153] 9p: Fix possible regressions when ->get_sb fails.

->get_sb can fail causing some badness. this patch fixes
   * clear sb->fs_s_info in kill_sb.
   * deactivate_locked_super() calls kill_sb (v9fs_kill_super) which closes the
     destroys the client, clunks all its fids and closes the v9fs session.
     Attempting to do it twice will cause an oops.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 fs/9p/vfs_super.c | 11 +++++++----
 1 file changed, 7 insertions(+), 4 deletions(-)

diff --git a/fs/9p/vfs_super.c b/fs/9p/vfs_super.c
index a9d7d08cfbe..2495af4ad9a 100644
--- a/fs/9p/vfs_super.c
+++ b/fs/9p/vfs_super.c
@@ -120,7 +120,6 @@ static int v9fs_get_sb(struct file_system_type *fs_type, int flags,
 
 	P9_DPRINTK(P9_DEBUG_VFS, " \n");
 
-	st = NULL;
 	v9ses = kzalloc(sizeof(struct v9fs_session_info), GFP_KERNEL);
 	if (!v9ses)
 		return -ENOMEM;
@@ -173,10 +172,8 @@ P9_DPRINTK(P9_DEBUG_VFS, " simple set mount, return 0\n");
 	simple_set_mnt(mnt, sb);
 	return 0;
 
-release_sb:
-	deactivate_locked_super(sb);
-
 free_stat:
+	p9stat_free(st);
 	kfree(st);
 
 clunk_fid:
@@ -185,7 +182,12 @@ clunk_fid:
 close_session:
 	v9fs_session_close(v9ses);
 	kfree(v9ses);
+	return retval;
 
+release_sb:
+	p9stat_free(st);
+	kfree(st);
+	deactivate_locked_super(sb);
 	return retval;
 }
 
@@ -207,6 +209,7 @@ static void v9fs_kill_super(struct super_block *s)
 
 	v9fs_session_close(v9ses);
 	kfree(v9ses);
+	s->s_fs_info = NULL;
 	P9_DPRINTK(P9_DEBUG_VFS, "exiting kill_super\n");
 }
 
-- 
GitLab


From 4d3297ca5bf37ff5956f76fb352e009880aad62d Mon Sep 17 00:00:00 2001
From: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Date: Sun, 19 Jul 2009 13:41:51 -0600
Subject: [PATCH 0938/1153] 9p: Remove redundant inode uid/gid assignment

Remove a redundant update of inode's i_uid and i_gid
after v9fs_get_inode() since the latter already sets up
a new inode and sets the proper uid and gid values.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 fs/9p/vfs_super.c | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/fs/9p/vfs_super.c b/fs/9p/vfs_super.c
index 2495af4ad9a..072dce09447 100644
--- a/fs/9p/vfs_super.c
+++ b/fs/9p/vfs_super.c
@@ -113,8 +113,6 @@ static int v9fs_get_sb(struct file_system_type *fs_type, int flags,
 	struct v9fs_session_info *v9ses = NULL;
 	struct p9_wstat *st = NULL;
 	int mode = S_IRWXUGO | S_ISVTX;
-	uid_t uid = current_fsuid();
-	gid_t gid = current_fsgid();
 	struct p9_fid *fid;
 	int retval = 0;
 
@@ -149,9 +147,6 @@ static int v9fs_get_sb(struct file_system_type *fs_type, int flags,
 		goto release_sb;
 	}
 
-	inode->i_uid = uid;
-	inode->i_gid = gid;
-
 	root = d_alloc_root(inode);
 	if (!root) {
 		iput(inode);
-- 
GitLab


From 5fd131893793567c361ae64cbeb28a2a753bbe35 Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Thu, 30 Jul 2009 17:01:53 +0200
Subject: [PATCH 0939/1153] ocfs2: Don't oops in ocfs2_kill_sb on a failed
 mount

If we fail to mount the filesystem, we have to be careful not to dereference
uninitialized structures in ocfs2_kill_sb.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/super.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/fs/ocfs2/super.c b/fs/ocfs2/super.c
index b0ee0fdf799..a3f8871d21f 100644
--- a/fs/ocfs2/super.c
+++ b/fs/ocfs2/super.c
@@ -1218,13 +1218,17 @@ static void ocfs2_kill_sb(struct super_block *sb)
 {
 	struct ocfs2_super *osb = OCFS2_SB(sb);
 
+	/* Failed mount? */
+	if (!osb || atomic_read(&osb->vol_state) == VOLUME_DISABLED)
+		goto out;
+
 	/* Prevent further queueing of inode drop events */
 	spin_lock(&dentry_list_lock);
 	ocfs2_set_osb_flag(osb, OCFS2_OSB_DROP_DENTRY_LOCK_IMMED);
 	spin_unlock(&dentry_list_lock);
 	/* Wait for work to finish and/or remove it */
 	cancel_work_sync(&osb->dentry_lock_work);
-
+out:
 	kill_block_super(sb);
 }
 
-- 
GitLab


From 48559b4c30708ebdc849483da9fb83ee08c6c908 Mon Sep 17 00:00:00 2001
From: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Date: Mon, 17 Aug 2009 16:32:18 -0500
Subject: [PATCH 0940/1153] 9p: Add missing cast for the error return value in
 v9fs_get_inode

Cast the error return value (ENOMEM) in v9fs_get_inode() to its
correct type using ERR_PTR.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 fs/9p/vfs_inode.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/9p/vfs_inode.c b/fs/9p/vfs_inode.c
index fac30d21851..06a223d50a8 100644
--- a/fs/9p/vfs_inode.c
+++ b/fs/9p/vfs_inode.c
@@ -215,7 +215,7 @@ struct inode *v9fs_get_inode(struct super_block *sb, int mode)
 	inode = new_inode(sb);
 	if (!inode) {
 		P9_EPRINTK(KERN_WARNING, "Problem allocating inode\n");
-		return -ENOMEM;
+		return ERR_PTR(-ENOMEM);
 	}
 
 	inode->i_mode = mode;
-- 
GitLab


From 0aad37ef3deed118d3816e1d1a600eb2ec9dcb87 Mon Sep 17 00:00:00 2001
From: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Date: Mon, 17 Aug 2009 16:38:45 -0500
Subject: [PATCH 0941/1153] net/9p: insulate the client against an invalid
 error code sent by a 9p server

A looney tunes server sending an invalid error code (which is !IS_ERR_VALUE)
can result in a client oops. So fix it by adding a check and converting unknown
or invalid error codes to -ESERVERFAULT.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 net/9p/client.c | 7 +------
 net/9p/error.c  | 2 +-
 2 files changed, 2 insertions(+), 7 deletions(-)

diff --git a/net/9p/client.c b/net/9p/client.c
index 7bbd2d5ae8d..5bf5f227dbe 100644
--- a/net/9p/client.c
+++ b/net/9p/client.c
@@ -411,14 +411,9 @@ static int p9_check_errors(struct p9_client *c, struct p9_req_t *req)
 		if (c->dotu)
 			err = -ecode;
 
-		if (!err) {
+		if (!err || !IS_ERR_VALUE(err))
 			err = p9_errstr2errno(ename, strlen(ename));
 
-			/* string match failed */
-			if (!err)
-				err = -ESERVERFAULT;
-		}
-
 		P9_DPRINTK(P9_DEBUG_9P, "<<< RERROR (%d) %s\n", -ecode, ename);
 
 		kfree(ename);
diff --git a/net/9p/error.c b/net/9p/error.c
index fdebe431406..52518512a93 100644
--- a/net/9p/error.c
+++ b/net/9p/error.c
@@ -239,7 +239,7 @@ int p9_errstr2errno(char *errstr, int len)
 		errstr[len] = 0;
 		printk(KERN_ERR "%s: server reported unknown error %s\n",
 			__func__, errstr);
-		errno = 1;
+		errno = ESERVERFAULT;
 	}
 
 	return -errno;
-- 
GitLab


From 4b53e4b500779230aedd5355940aeaaed0b5353b Mon Sep 17 00:00:00 2001
From: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Date: Mon, 17 Aug 2009 16:42:28 -0500
Subject: [PATCH 0942/1153] 9p: remove unnecessary v9fses->options which
 duplicates the mount string

The mount options string is saved in sb->s_options. This patch removes
the redundant duplicating of the mount options. Also, since we are not
displaying anything special in show options, we replace v9fs_show_options
with generic_show_options for now.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 fs/9p/v9fs.c      | 21 +++++----------------
 fs/9p/v9fs.h      |  1 -
 fs/9p/vfs_super.c | 23 +++++------------------
 3 files changed, 10 insertions(+), 35 deletions(-)

diff --git a/fs/9p/v9fs.c b/fs/9p/v9fs.c
index 332b5ff02fe..f7003cfac63 100644
--- a/fs/9p/v9fs.c
+++ b/fs/9p/v9fs.c
@@ -76,7 +76,7 @@ static const match_table_t tokens = {
  * Return 0 upon success, -ERRNO upon failure.
  */
 
-static int v9fs_parse_options(struct v9fs_session_info *v9ses)
+static int v9fs_parse_options(struct v9fs_session_info *v9ses, char *opts)
 {
 	char *options;
 	substring_t args[MAX_OPT_ARGS];
@@ -90,10 +90,10 @@ static int v9fs_parse_options(struct v9fs_session_info *v9ses)
 	v9ses->debug = 0;
 	v9ses->cache = 0;
 
-	if (!v9ses->options)
+	if (!opts)
 		return 0;
 
-	options = kstrdup(v9ses->options, GFP_KERNEL);
+	options = kstrdup(opts, GFP_KERNEL);
 	if (!options) {
 		P9_DPRINTK(P9_DEBUG_ERROR,
 			   "failed to allocate copy of option string\n");
@@ -206,24 +206,14 @@ struct p9_fid *v9fs_session_init(struct v9fs_session_info *v9ses,
 	v9ses->uid = ~0;
 	v9ses->dfltuid = V9FS_DEFUID;
 	v9ses->dfltgid = V9FS_DEFGID;
-	if (data) {
-		v9ses->options = kstrdup(data, GFP_KERNEL);
-		if (!v9ses->options) {
-			P9_DPRINTK(P9_DEBUG_ERROR,
-			   "failed to allocate copy of option string\n");
-			retval = -ENOMEM;
-			goto error;
-		}
-	}
 
-	rc = v9fs_parse_options(v9ses);
+	rc = v9fs_parse_options(v9ses, data);
 	if (rc < 0) {
 		retval = rc;
 		goto error;
 	}
 
-	v9ses->clnt = p9_client_create(dev_name, v9ses->options);
-
+	v9ses->clnt = p9_client_create(dev_name, data);
 	if (IS_ERR(v9ses->clnt)) {
 		retval = PTR_ERR(v9ses->clnt);
 		v9ses->clnt = NULL;
@@ -280,7 +270,6 @@ void v9fs_session_close(struct v9fs_session_info *v9ses)
 
 	__putname(v9ses->uname);
 	__putname(v9ses->aname);
-	kfree(v9ses->options);
 }
 
 /**
diff --git a/fs/9p/v9fs.h b/fs/9p/v9fs.h
index a7d56719299..38762bf102a 100644
--- a/fs/9p/v9fs.h
+++ b/fs/9p/v9fs.h
@@ -85,7 +85,6 @@ struct v9fs_session_info {
 	unsigned int afid;
 	unsigned int cache;
 
-	char *options;		/* copy of mount options */
 	char *uname;		/* user name to mount as */
 	char *aname;		/* name of remote hierarchy being mounted */
 	unsigned int maxdata;	/* max data for client interface */
diff --git a/fs/9p/vfs_super.c b/fs/9p/vfs_super.c
index 072dce09447..8961f1a8f66 100644
--- a/fs/9p/vfs_super.c
+++ b/fs/9p/vfs_super.c
@@ -81,7 +81,7 @@ static int v9fs_set_super(struct super_block *s, void *data)
 
 static void
 v9fs_fill_super(struct super_block *sb, struct v9fs_session_info *v9ses,
-		int flags)
+		int flags, void *data)
 {
 	sb->s_maxbytes = MAX_LFS_FILESIZE;
 	sb->s_blocksize_bits = fls(v9ses->maxdata - 1);
@@ -91,6 +91,8 @@ v9fs_fill_super(struct super_block *sb, struct v9fs_session_info *v9ses,
 
 	sb->s_flags = flags | MS_ACTIVE | MS_SYNCHRONOUS | MS_DIRSYNC |
 	    MS_NOATIME;
+
+	save_mount_options(sb, data);
 }
 
 /**
@@ -139,7 +141,7 @@ static int v9fs_get_sb(struct file_system_type *fs_type, int flags,
 		retval = PTR_ERR(sb);
 		goto free_stat;
 	}
-	v9fs_fill_super(sb, v9ses, flags);
+	v9fs_fill_super(sb, v9ses, flags, data);
 
 	inode = v9fs_get_inode(sb, S_IFDIR | mode);
 	if (IS_ERR(inode)) {
@@ -208,21 +210,6 @@ static void v9fs_kill_super(struct super_block *s)
 	P9_DPRINTK(P9_DEBUG_VFS, "exiting kill_super\n");
 }
 
-/**
- * v9fs_show_options - Show mount options in /proc/mounts
- * @m: seq_file to write to
- * @mnt: mount descriptor
- *
- */
-
-static int v9fs_show_options(struct seq_file *m, struct vfsmount *mnt)
-{
-	struct v9fs_session_info *v9ses = mnt->mnt_sb->s_fs_info;
-	if (v9ses->options != NULL)
-		seq_printf(m, ",%s", v9ses->options);
-	return 0;
-}
-
 static void
 v9fs_umount_begin(struct super_block *sb)
 {
@@ -235,7 +222,7 @@ v9fs_umount_begin(struct super_block *sb)
 static const struct super_operations v9fs_super_ops = {
 	.statfs = simple_statfs,
 	.clear_inode = v9fs_clear_inode,
-	.show_options = v9fs_show_options,
+	.show_options = generic_show_options,
 	.umount_begin = v9fs_umount_begin,
 };
 
-- 
GitLab


From 7815f4be4026b6c5027058102ae67a4b9feffa5f Mon Sep 17 00:00:00 2001
From: Eric Van Hensbergen <ericvh@gmail.com>
Date: Mon, 17 Aug 2009 16:49:44 -0500
Subject: [PATCH 0943/1153] 9p: update documentation pointers

Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
---
 Documentation/filesystems/9p.txt | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/filesystems/9p.txt b/Documentation/filesystems/9p.txt
index bf8080640eb..6208f55c44c 100644
--- a/Documentation/filesystems/9p.txt
+++ b/Documentation/filesystems/9p.txt
@@ -123,6 +123,9 @@ available from the same CVS repository.
 There are user and developer mailing lists available through the v9fs project
 on sourceforge (http://sourceforge.net/projects/v9fs).
 
+A stand-alone version of the module (which should build for any 2.6 kernel)
+is available via (http://github.com/ericvh/9p-sac/tree/master)
+
 News and other information is maintained on SWiK (http://swik.net/v9fs).
 
 Bug reports may be issued through the kernel.org bugzilla 
-- 
GitLab


From f2d84b65b9778e8a35dd904f7d3993f0a60c9756 Mon Sep 17 00:00:00 2001
From: Zhaolei <zhaolei@cn.fujitsu.com>
Date: Fri, 7 Aug 2009 18:55:48 +0800
Subject: [PATCH 0944/1153] ftrace: Unify effect of writing to trace_options
 and option/*

"echo noglobal-clock > trace_options" can be used to change trace
clock but "echo 0 > options/global-clock" can't. The flag toggling
will be silently accepted without actually changing the clock callback.

We can fix it by using set_tracer_flags() in
trace_options_core_write().

Changelog:
v1->v2: Simplified switch() after Li Zefan <lizf@cn.fujitsu.com>'s
        suggestion

Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
---
 kernel/trace/trace.c | 12 ++----------
 1 file changed, 2 insertions(+), 10 deletions(-)

diff --git a/kernel/trace/trace.c b/kernel/trace/trace.c
index c22b40f8f57..8c358395d33 100644
--- a/kernel/trace/trace.c
+++ b/kernel/trace/trace.c
@@ -3896,17 +3896,9 @@ trace_options_core_write(struct file *filp, const char __user *ubuf, size_t cnt,
 	if (ret < 0)
 		return ret;
 
-	switch (val) {
-	case 0:
-		trace_flags &= ~(1 << index);
-		break;
-	case 1:
-		trace_flags |= 1 << index;
-		break;
-
-	default:
+	if (val != 0 && val != 1)
 		return -EINVAL;
-	}
+	set_tracer_flags(1 << index, val);
 
 	*ppos += cnt;
 
-- 
GitLab


From 80ffb3cceaefa405f2ecd46d66500ed8d53efe74 Mon Sep 17 00:00:00 2001
From: NeilBrown <neilb@suse.de>
Date: Tue, 18 Aug 2009 10:35:26 +1000
Subject: [PATCH 0945/1153] Fix new incorrect error return from do_md_stop.

Recent commit c8c00a6915a2e3d10416e8bdd3138429beb96210
changed the exit paths in do_md_stop and was not quite
careful enough.  There is one path were 'err' now needs
to be cleared but it isn't.
So setting an array to readonly (with mdadm --readonly) will
work, but will incorrectly report and error: ENXIO.

Signed-off-by: NeilBrown <neilb@suse.de>
---
 drivers/md/md.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/md/md.c b/drivers/md/md.c
index 103f2d33fa8..9dd872000ce 100644
--- a/drivers/md/md.c
+++ b/drivers/md/md.c
@@ -4364,6 +4364,7 @@ static int do_md_stop(mddev_t * mddev, int mode, int is_open)
 		if (mode == 1)
 			set_disk_ro(disk, 1);
 		clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
+		err = 0;
 	}
 out:
 	mutex_unlock(&mddev->open_mutex);
-- 
GitLab


From c6ba973b8fa97422aab4204f7d79f1d413cde925 Mon Sep 17 00:00:00 2001
From: Ralf Baechle <ralf@linux-mips.org>
Date: Mon, 17 Aug 2009 18:05:32 -0700
Subject: [PATCH 0946/1153] NETROM: Fix use of static buffer

The static variable used by nr_call_to_digi might result in corruption if
multiple threads are trying to usee a node or neighbour via ioctl.  Fixed
by having the caller pass a structure in.  This is safe because nr_add_node
rsp. nr_add_neigh will allocate a permanent structure, if needed.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/netrom/nr_route.c | 21 ++++++++++++---------
 1 file changed, 12 insertions(+), 9 deletions(-)

diff --git a/net/netrom/nr_route.c b/net/netrom/nr_route.c
index e943c16552a..4eb1ac9a767 100644
--- a/net/netrom/nr_route.c
+++ b/net/netrom/nr_route.c
@@ -630,23 +630,23 @@ out:
 	return dev;
 }
 
-static ax25_digi *nr_call_to_digi(int ndigis, ax25_address *digipeaters)
+static ax25_digi *nr_call_to_digi(ax25_digi *digi, int ndigis,
+	ax25_address *digipeaters)
 {
-	static ax25_digi ax25_digi;
 	int i;
 
 	if (ndigis == 0)
 		return NULL;
 
 	for (i = 0; i < ndigis; i++) {
-		ax25_digi.calls[i]    = digipeaters[i];
-		ax25_digi.repeated[i] = 0;
+		digi->calls[i]    = digipeaters[i];
+		digi->repeated[i] = 0;
 	}
 
-	ax25_digi.ndigi      = ndigis;
-	ax25_digi.lastrepeat = -1;
+	digi->ndigi      = ndigis;
+	digi->lastrepeat = -1;
 
-	return &ax25_digi;
+	return digi;
 }
 
 /*
@@ -656,6 +656,7 @@ int nr_rt_ioctl(unsigned int cmd, void __user *arg)
 {
 	struct nr_route_struct nr_route;
 	struct net_device *dev;
+	ax25_digi digi;
 	int ret;
 
 	switch (cmd) {
@@ -673,13 +674,15 @@ int nr_rt_ioctl(unsigned int cmd, void __user *arg)
 			ret = nr_add_node(&nr_route.callsign,
 				nr_route.mnemonic,
 				&nr_route.neighbour,
-				nr_call_to_digi(nr_route.ndigis, nr_route.digipeaters),
+				nr_call_to_digi(&digi, nr_route.ndigis,
+						nr_route.digipeaters),
 				dev, nr_route.quality,
 				nr_route.obs_count);
 			break;
 		case NETROM_NEIGH:
 			ret = nr_add_neigh(&nr_route.callsign,
-				nr_call_to_digi(nr_route.ndigis, nr_route.digipeaters),
+				nr_call_to_digi(&digi, nr_route.ndigis,
+						nr_route.digipeaters),
 				dev, nr_route.quality);
 			break;
 		default:
-- 
GitLab


From c1a8f1f1c8e01eab5862c8db39b49ace814e6c66 Mon Sep 17 00:00:00 2001
From: Eric Dumazet <eric.dumazet@gmail.com>
Date: Sun, 16 Aug 2009 09:36:49 +0000
Subject: [PATCH 0947/1153] net: restore gnet_stats_basic to previous
 definition

In 5e140dfc1fe87eae27846f193086724806b33c7d "net: reorder struct Qdisc
for better SMP performance" the definition of struct gnet_stats_basic
changed incompatibly, as copies of this struct are shipped to
userland via netlink.

Restoring old behavior is not welcome, for performance reason.

Fix is to use a private structure for kernel, and
teach gnet_stats_copy_basic() to convert from kernel to user land,
using legacy structure (struct gnet_stats_basic)

Based on a report and initial patch from Michael Spang.

Reported-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 include/linux/gen_stats.h          |  5 +++++
 include/net/act_api.h              |  2 +-
 include/net/gen_stats.h            | 10 +++++-----
 include/net/netfilter/xt_rateest.h |  2 +-
 include/net/sch_generic.h          |  2 +-
 net/core/gen_estimator.c           | 12 ++++++------
 net/core/gen_stats.c               | 11 ++++++++---
 net/netfilter/xt_RATEEST.c         |  2 +-
 net/sched/sch_atm.c                |  2 +-
 net/sched/sch_cbq.c                |  2 +-
 net/sched/sch_drr.c                |  2 +-
 net/sched/sch_hfsc.c               |  2 +-
 net/sched/sch_htb.c                |  2 +-
 13 files changed, 33 insertions(+), 23 deletions(-)

diff --git a/include/linux/gen_stats.h b/include/linux/gen_stats.h
index 0ffa41df0ee..710e901085d 100644
--- a/include/linux/gen_stats.h
+++ b/include/linux/gen_stats.h
@@ -19,6 +19,11 @@ enum {
  * @packets: number of seen packets
  */
 struct gnet_stats_basic
+{
+	__u64	bytes;
+	__u32	packets;
+};
+struct gnet_stats_basic_packed
 {
 	__u64	bytes;
 	__u32	packets;
diff --git a/include/net/act_api.h b/include/net/act_api.h
index 565eed8fe49..c05fd717c58 100644
--- a/include/net/act_api.h
+++ b/include/net/act_api.h
@@ -16,7 +16,7 @@ struct tcf_common {
 	u32				tcfc_capab;
 	int				tcfc_action;
 	struct tcf_t			tcfc_tm;
-	struct gnet_stats_basic		tcfc_bstats;
+	struct gnet_stats_basic_packed	tcfc_bstats;
 	struct gnet_stats_queue		tcfc_qstats;
 	struct gnet_stats_rate_est	tcfc_rate_est;
 	spinlock_t			tcfc_lock;
diff --git a/include/net/gen_stats.h b/include/net/gen_stats.h
index d136b5240ef..c1488553e34 100644
--- a/include/net/gen_stats.h
+++ b/include/net/gen_stats.h
@@ -28,7 +28,7 @@ extern int gnet_stats_start_copy_compat(struct sk_buff *skb, int type,
 					spinlock_t *lock, struct gnet_dump *d);
 
 extern int gnet_stats_copy_basic(struct gnet_dump *d,
-				 struct gnet_stats_basic *b);
+				 struct gnet_stats_basic_packed *b);
 extern int gnet_stats_copy_rate_est(struct gnet_dump *d,
 				    struct gnet_stats_rate_est *r);
 extern int gnet_stats_copy_queue(struct gnet_dump *d,
@@ -37,14 +37,14 @@ extern int gnet_stats_copy_app(struct gnet_dump *d, void *st, int len);
 
 extern int gnet_stats_finish_copy(struct gnet_dump *d);
 
-extern int gen_new_estimator(struct gnet_stats_basic *bstats,
+extern int gen_new_estimator(struct gnet_stats_basic_packed *bstats,
 			     struct gnet_stats_rate_est *rate_est,
 			     spinlock_t *stats_lock, struct nlattr *opt);
-extern void gen_kill_estimator(struct gnet_stats_basic *bstats,
+extern void gen_kill_estimator(struct gnet_stats_basic_packed *bstats,
 			       struct gnet_stats_rate_est *rate_est);
-extern int gen_replace_estimator(struct gnet_stats_basic *bstats,
+extern int gen_replace_estimator(struct gnet_stats_basic_packed *bstats,
 				 struct gnet_stats_rate_est *rate_est,
 				 spinlock_t *stats_lock, struct nlattr *opt);
-extern bool gen_estimator_active(const struct gnet_stats_basic *bstats,
+extern bool gen_estimator_active(const struct gnet_stats_basic_packed *bstats,
 				 const struct gnet_stats_rate_est *rate_est);
 #endif
diff --git a/include/net/netfilter/xt_rateest.h b/include/net/netfilter/xt_rateest.h
index 65d594dffbf..ddbf37e1961 100644
--- a/include/net/netfilter/xt_rateest.h
+++ b/include/net/netfilter/xt_rateest.h
@@ -8,7 +8,7 @@ struct xt_rateest {
 	spinlock_t			lock;
 	struct gnet_estimator		params;
 	struct gnet_stats_rate_est	rstats;
-	struct gnet_stats_basic		bstats;
+	struct gnet_stats_basic_packed	bstats;
 };
 
 extern struct xt_rateest *xt_rateest_lookup(const char *name);
diff --git a/include/net/sch_generic.h b/include/net/sch_generic.h
index 964ffa0d881..5482e9582f5 100644
--- a/include/net/sch_generic.h
+++ b/include/net/sch_generic.h
@@ -72,7 +72,7 @@ struct Qdisc
 	 */
 	unsigned long		state;
 	struct sk_buff_head	q;
-	struct gnet_stats_basic bstats;
+	struct gnet_stats_basic_packed bstats;
 	struct gnet_stats_queue	qstats;
 };
 
diff --git a/net/core/gen_estimator.c b/net/core/gen_estimator.c
index 78e5bfc454a..493775f4f2f 100644
--- a/net/core/gen_estimator.c
+++ b/net/core/gen_estimator.c
@@ -81,7 +81,7 @@
 struct gen_estimator
 {
 	struct list_head	list;
-	struct gnet_stats_basic	*bstats;
+	struct gnet_stats_basic_packed	*bstats;
 	struct gnet_stats_rate_est	*rate_est;
 	spinlock_t		*stats_lock;
 	int			ewma_log;
@@ -165,7 +165,7 @@ static void gen_add_node(struct gen_estimator *est)
 }
 
 static
-struct gen_estimator *gen_find_node(const struct gnet_stats_basic *bstats,
+struct gen_estimator *gen_find_node(const struct gnet_stats_basic_packed *bstats,
 				    const struct gnet_stats_rate_est *rate_est)
 {
 	struct rb_node *p = est_root.rb_node;
@@ -202,7 +202,7 @@ struct gen_estimator *gen_find_node(const struct gnet_stats_basic *bstats,
  *
  * NOTE: Called under rtnl_mutex
  */
-int gen_new_estimator(struct gnet_stats_basic *bstats,
+int gen_new_estimator(struct gnet_stats_basic_packed *bstats,
 		      struct gnet_stats_rate_est *rate_est,
 		      spinlock_t *stats_lock,
 		      struct nlattr *opt)
@@ -262,7 +262,7 @@ static void __gen_kill_estimator(struct rcu_head *head)
  *
  * NOTE: Called under rtnl_mutex
  */
-void gen_kill_estimator(struct gnet_stats_basic *bstats,
+void gen_kill_estimator(struct gnet_stats_basic_packed *bstats,
 			struct gnet_stats_rate_est *rate_est)
 {
 	struct gen_estimator *e;
@@ -292,7 +292,7 @@ EXPORT_SYMBOL(gen_kill_estimator);
  *
  * Returns 0 on success or a negative error code.
  */
-int gen_replace_estimator(struct gnet_stats_basic *bstats,
+int gen_replace_estimator(struct gnet_stats_basic_packed *bstats,
 			  struct gnet_stats_rate_est *rate_est,
 			  spinlock_t *stats_lock, struct nlattr *opt)
 {
@@ -308,7 +308,7 @@ EXPORT_SYMBOL(gen_replace_estimator);
  *
  * Returns true if estimator is active, and false if not.
  */
-bool gen_estimator_active(const struct gnet_stats_basic *bstats,
+bool gen_estimator_active(const struct gnet_stats_basic_packed *bstats,
 			  const struct gnet_stats_rate_est *rate_est)
 {
 	ASSERT_RTNL();
diff --git a/net/core/gen_stats.c b/net/core/gen_stats.c
index c3d0ffeac24..8569310268a 100644
--- a/net/core/gen_stats.c
+++ b/net/core/gen_stats.c
@@ -106,16 +106,21 @@ gnet_stats_start_copy(struct sk_buff *skb, int type, spinlock_t *lock,
  * if the room in the socket buffer was not sufficient.
  */
 int
-gnet_stats_copy_basic(struct gnet_dump *d, struct gnet_stats_basic *b)
+gnet_stats_copy_basic(struct gnet_dump *d, struct gnet_stats_basic_packed *b)
 {
 	if (d->compat_tc_stats) {
 		d->tc_stats.bytes = b->bytes;
 		d->tc_stats.packets = b->packets;
 	}
 
-	if (d->tail)
-		return gnet_stats_copy(d, TCA_STATS_BASIC, b, sizeof(*b));
+	if (d->tail) {
+		struct gnet_stats_basic sb;
 
+		memset(&sb, 0, sizeof(sb));
+		sb.bytes = b->bytes;
+		sb.packets = b->packets;
+		return gnet_stats_copy(d, TCA_STATS_BASIC, &sb, sizeof(sb));
+	}
 	return 0;
 }
 
diff --git a/net/netfilter/xt_RATEEST.c b/net/netfilter/xt_RATEEST.c
index 43f5676b1af..d80b8192e0d 100644
--- a/net/netfilter/xt_RATEEST.c
+++ b/net/netfilter/xt_RATEEST.c
@@ -74,7 +74,7 @@ static unsigned int
 xt_rateest_tg(struct sk_buff *skb, const struct xt_target_param *par)
 {
 	const struct xt_rateest_target_info *info = par->targinfo;
-	struct gnet_stats_basic *stats = &info->est->bstats;
+	struct gnet_stats_basic_packed *stats = &info->est->bstats;
 
 	spin_lock_bh(&info->est->lock);
 	stats->bytes += skb->len;
diff --git a/net/sched/sch_atm.c b/net/sched/sch_atm.c
index 2a8b83af7c4..ab82f145f68 100644
--- a/net/sched/sch_atm.c
+++ b/net/sched/sch_atm.c
@@ -49,7 +49,7 @@ struct atm_flow_data {
 	struct socket		*sock;		/* for closing */
 	u32			classid;	/* x:y type ID */
 	int			ref;		/* reference count */
-	struct gnet_stats_basic	bstats;
+	struct gnet_stats_basic_packed	bstats;
 	struct gnet_stats_queue	qstats;
 	struct atm_flow_data	*next;
 	struct atm_flow_data	*excess;	/* flow for excess traffic;
diff --git a/net/sched/sch_cbq.c b/net/sched/sch_cbq.c
index 23a167670fd..d5798e17a83 100644
--- a/net/sched/sch_cbq.c
+++ b/net/sched/sch_cbq.c
@@ -128,7 +128,7 @@ struct cbq_class
 	long			avgidle;
 	long			deficit;	/* Saved deficit for WRR */
 	psched_time_t		penalized;
-	struct gnet_stats_basic bstats;
+	struct gnet_stats_basic_packed bstats;
 	struct gnet_stats_queue qstats;
 	struct gnet_stats_rate_est rate_est;
 	struct tc_cbq_xstats	xstats;
diff --git a/net/sched/sch_drr.c b/net/sched/sch_drr.c
index 7597fe14686..12b2fb04b29 100644
--- a/net/sched/sch_drr.c
+++ b/net/sched/sch_drr.c
@@ -22,7 +22,7 @@ struct drr_class {
 	unsigned int			refcnt;
 	unsigned int			filter_cnt;
 
-	struct gnet_stats_basic		bstats;
+	struct gnet_stats_basic_packed		bstats;
 	struct gnet_stats_queue		qstats;
 	struct gnet_stats_rate_est	rate_est;
 	struct list_head		alist;
diff --git a/net/sched/sch_hfsc.c b/net/sched/sch_hfsc.c
index 362c2811b2d..dad0144423d 100644
--- a/net/sched/sch_hfsc.c
+++ b/net/sched/sch_hfsc.c
@@ -116,7 +116,7 @@ struct hfsc_class
 	struct Qdisc_class_common cl_common;
 	unsigned int	refcnt;		/* usage count */
 
-	struct gnet_stats_basic bstats;
+	struct gnet_stats_basic_packed bstats;
 	struct gnet_stats_queue qstats;
 	struct gnet_stats_rate_est rate_est;
 	unsigned int	level;		/* class level in hierarchy */
diff --git a/net/sched/sch_htb.c b/net/sched/sch_htb.c
index 88cd0262662..ec4d46399d5 100644
--- a/net/sched/sch_htb.c
+++ b/net/sched/sch_htb.c
@@ -74,7 +74,7 @@ enum htb_cmode {
 struct htb_class {
 	struct Qdisc_class_common common;
 	/* general class parameters */
-	struct gnet_stats_basic bstats;
+	struct gnet_stats_basic_packed bstats;
 	struct gnet_stats_queue qstats;
 	struct gnet_stats_rate_est rate_est;
 	struct tc_htb_xstats xstats;	/* our special stats */
-- 
GitLab


From 1154ecbd2f8298ef75609f5f8ed5aca96be599fb Mon Sep 17 00:00:00 2001
From: Zhang Qiang <zhangqiang.buaa@gmail.com>
Date: Tue, 18 Aug 2009 14:58:24 +0800
Subject: [PATCH 0948/1153] nilfs2: missing a read lock for segment writer in
 nilfs_attach_checkpoint()

'ns_cno' of structure 'the_nilfs' must be protected from segment
writer, in other words, the caller of nilfs_get_checkpoint should hold
read lock for nilfs->ns_segctor_sem.  This patch adds the lock/unlock
operations in nilfs_attach_checkpoint() when calling
nilfs_cpfile_get_checkpoint().

Signed-off-by: Zhang Qiang <zhangqiang.buaa@gmail.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
---
 fs/nilfs2/super.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/fs/nilfs2/super.c b/fs/nilfs2/super.c
index 8e2ec43b18f..151964f0de4 100644
--- a/fs/nilfs2/super.c
+++ b/fs/nilfs2/super.c
@@ -416,8 +416,10 @@ int nilfs_attach_checkpoint(struct nilfs_sb_info *sbi, __u64 cno)
 	if (unlikely(err))
 		goto failed;
 
+	down_read(&nilfs->ns_segctor_sem);
 	err = nilfs_cpfile_get_checkpoint(nilfs->ns_cpfile, cno, 0, &raw_cp,
 					  &bh_cp);
+	up_read(&nilfs->ns_segctor_sem);
 	if (unlikely(err)) {
 		if (err == -ENOENT || err == -EINVAL) {
 			printk(KERN_ERR
-- 
GitLab


From 6b99ecec25c8fd501e74306f5d23dd0365065e2a Mon Sep 17 00:00:00 2001
From: Christoph Hellwig <hch@lst.de>
Date: Thu, 6 Aug 2009 23:00:38 +0200
Subject: [PATCH 0949/1153] microblaze: use the generic ack_bad_irq
 implementation

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michal Simek <monstr@monstr.eu>
---
 arch/microblaze/include/asm/hardirq.h | 2 --
 arch/microblaze/kernel/irq.c          | 9 ---------
 2 files changed, 11 deletions(-)

diff --git a/arch/microblaze/include/asm/hardirq.h b/arch/microblaze/include/asm/hardirq.h
index 41e1e1aa36a..cd1ac9aad56 100644
--- a/arch/microblaze/include/asm/hardirq.h
+++ b/arch/microblaze/include/asm/hardirq.h
@@ -12,8 +12,6 @@
 /* should be defined in each interrupt controller driver */
 extern unsigned int get_irq(struct pt_regs *regs);
 
-#define ack_bad_irq ack_bad_irq
-void ack_bad_irq(unsigned int irq);
 #include <asm-generic/hardirq.h>
 
 #endif /* _ASM_MICROBLAZE_HARDIRQ_H */
diff --git a/arch/microblaze/kernel/irq.c b/arch/microblaze/kernel/irq.c
index f688ee93e3b..7d5ddd62d4d 100644
--- a/arch/microblaze/kernel/irq.c
+++ b/arch/microblaze/kernel/irq.c
@@ -30,15 +30,6 @@ unsigned int irq_of_parse_and_map(struct device_node *dev, int index)
 }
 EXPORT_SYMBOL_GPL(irq_of_parse_and_map);
 
-/*
- * 'what should we do if we get a hw irq event on an illegal vector'.
- * each architecture has to answer this themselves.
- */
-void ack_bad_irq(unsigned int irq)
-{
-	printk(KERN_WARNING "unexpected IRQ trap at vector %02x\n", irq);
-}
-
 static u32 concurrent_irq;
 
 void do_IRQ(struct pt_regs *regs)
-- 
GitLab


From 892ee92b81b6e7fa5f6147c96e11c6c1b9802fc6 Mon Sep 17 00:00:00 2001
From: John Williams <john.williams@petalogix.com>
Date: Wed, 29 Jul 2009 22:08:40 +1000
Subject: [PATCH 0950/1153] microblaze: Sane handling of missing timer/intc in
 device tree

This code path doesn't test any returned pointers for NULL, leading to a bad
kernel page fault if there's no timer/intc found.

Slightly better is to BUG(), but even better still would be a printk beforehand.

Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
---
 arch/microblaze/kernel/intc.c  | 2 ++
 arch/microblaze/kernel/timer.c | 2 ++
 2 files changed, 4 insertions(+)

diff --git a/arch/microblaze/kernel/intc.c b/arch/microblaze/kernel/intc.c
index b15605299a5..6eea6f92b84 100644
--- a/arch/microblaze/kernel/intc.c
+++ b/arch/microblaze/kernel/intc.c
@@ -12,6 +12,7 @@
 #include <linux/irq.h>
 #include <asm/page.h>
 #include <linux/io.h>
+#include <linux/bug.h>
 
 #include <asm/prom.h>
 #include <asm/irq.h>
@@ -130,6 +131,7 @@ void __init init_IRQ(void)
 		if (intc)
 			break;
 	}
+	BUG_ON(!intc);
 
 	intc_baseaddr = *(int *) of_get_property(intc, "reg", NULL);
 	intc_baseaddr = (unsigned long) ioremap(intc_baseaddr, PAGE_SIZE);
diff --git a/arch/microblaze/kernel/timer.c b/arch/microblaze/kernel/timer.c
index bdfa2f9f0c8..5499deae7fa 100644
--- a/arch/microblaze/kernel/timer.c
+++ b/arch/microblaze/kernel/timer.c
@@ -22,6 +22,7 @@
 #include <linux/clocksource.h>
 #include <linux/clockchips.h>
 #include <linux/io.h>
+#include <linux/bug.h>
 #include <asm/cpuinfo.h>
 #include <asm/setup.h>
 #include <asm/prom.h>
@@ -234,6 +235,7 @@ void __init time_init(void)
 		if (timer)
 			break;
 	}
+	BUG_ON(!timer);
 
 	timer_baseaddr = *(int *) of_get_property(timer, "reg", NULL);
 	timer_baseaddr = (unsigned long) ioremap(timer_baseaddr, PAGE_SIZE);
-- 
GitLab


From 2856ed35ead295a7cc8788d9ba860e746dfc92bb Mon Sep 17 00:00:00 2001
From: Michal Simek <monstr@monstr.eu>
Date: Thu, 6 Aug 2009 16:00:52 +0200
Subject: [PATCH 0951/1153] microblaze: Enable ppoll syscall

Signed-off-by: Michal Simek <monstr@monstr.eu>
---
 arch/microblaze/kernel/syscall_table.S | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/microblaze/kernel/syscall_table.S b/arch/microblaze/kernel/syscall_table.S
index 216db817beb..457216097df 100644
--- a/arch/microblaze/kernel/syscall_table.S
+++ b/arch/microblaze/kernel/syscall_table.S
@@ -313,7 +313,7 @@ ENTRY(sys_call_table)
 	.long sys_fchmodat
 	.long sys_faccessat
 	.long sys_ni_syscall /* pselect6 */
-	.long sys_ni_syscall /* sys_ppoll */
+	.long sys_ppoll
 	.long sys_unshare		/* 310 */
 	.long sys_set_robust_list
 	.long sys_get_robust_list
-- 
GitLab


From 8f37b6c9852ff79cc8472c44ea6f6485dfd58bd2 Mon Sep 17 00:00:00 2001
From: Michal Simek <monstr@monstr.eu>
Date: Tue, 11 Aug 2009 12:36:12 +0200
Subject: [PATCH 0952/1153] microblaze: Use klimit instead of _end for memory
 init

For noMMU system when you use larger rootfs image
there is problem with using _end label because
we increase klimit but in memory initialization
we use still _end which is wrong. Larger mtd rootfs
was rewritten by init_bootmem_node.

MMU kernel use static initialization where klimit
is setup to _end. There is no any other hanling
with klimit.

Signed-off-by: Michal Simek <monstr@monstr.eu>
---
 arch/microblaze/mm/init.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/microblaze/mm/init.c b/arch/microblaze/mm/init.c
index 8d92c4efe9a..f207f1a94db 100644
--- a/arch/microblaze/mm/init.c
+++ b/arch/microblaze/mm/init.c
@@ -130,13 +130,13 @@ void __init setup_memory(void)
 	 * (in case the address isn't page-aligned).
 	 */
 #ifndef CONFIG_MMU
-	map_size = init_bootmem_node(NODE_DATA(0), PFN_UP(TOPHYS((u32)_end)),
+	map_size = init_bootmem_node(NODE_DATA(0), PFN_UP(TOPHYS((u32)klimit)),
 					min_low_pfn, max_low_pfn);
 #else
 	map_size = init_bootmem_node(&contig_page_data,
-		PFN_UP(TOPHYS((u32)_end)), min_low_pfn, max_low_pfn);
+		PFN_UP(TOPHYS((u32)klimit)), min_low_pfn, max_low_pfn);
 #endif
-	lmb_reserve(PFN_UP(TOPHYS((u32)_end)) << PAGE_SHIFT, map_size);
+	lmb_reserve(PFN_UP(TOPHYS((u32)klimit)) << PAGE_SHIFT, map_size);
 
 	/* free bootmem is whole main memory */
 	free_bootmem(memory_start, memory_size);
-- 
GitLab


From 1fef7891755d99039592aa8d1ed02e981f38de15 Mon Sep 17 00:00:00 2001
From: Michal Simek <monstr@monstr.eu>
Date: Tue, 18 Aug 2009 11:05:11 +0200
Subject: [PATCH 0953/1153] microblaze: Update Microblaze defconfigs

Signed-off-by: Michal Simek <monstr@monstr.eu>
---
 arch/microblaze/configs/mmu_defconfig   | 70 ++++++++++---------
 arch/microblaze/configs/nommu_defconfig | 91 +++++++++++++++----------
 2 files changed, 91 insertions(+), 70 deletions(-)

diff --git a/arch/microblaze/configs/mmu_defconfig b/arch/microblaze/configs/mmu_defconfig
index bd0b85ec38f..09c32962b66 100644
--- a/arch/microblaze/configs/mmu_defconfig
+++ b/arch/microblaze/configs/mmu_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc6
-# Fri May 22 10:02:33 2009
+# Linux kernel version: 2.6.31-rc6
+# Tue Aug 18 11:00:02 2009
 #
 CONFIG_MICROBLAZE=y
 # CONFIG_SWAP is not set
@@ -18,7 +18,11 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_CSUM=y
+# CONFIG_PCI is not set
+CONFIG_NO_DMA=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -59,8 +63,8 @@ CONFIG_INITRAMFS_ROOT_GID=0
 CONFIG_RD_GZIP=y
 # CONFIG_RD_BZIP2 is not set
 # CONFIG_RD_LZMA is not set
-CONFIG_INITRAMFS_COMPRESSION_NONE=y
-# CONFIG_INITRAMFS_COMPRESSION_GZIP is not set
+# CONFIG_INITRAMFS_COMPRESSION_NONE is not set
+CONFIG_INITRAMFS_COMPRESSION_GZIP=y
 # CONFIG_INITRAMFS_COMPRESSION_BZIP2 is not set
 # CONFIG_INITRAMFS_COMPRESSION_LZMA is not set
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
@@ -71,7 +75,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -84,13 +87,22 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 # CONFIG_SHMEM is not set
 CONFIG_AIO=y
+
+#
+# Performance Counters
+#
 CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
 # CONFIG_SLOB is not set
 # CONFIG_PROFILING is not set
 # CONFIG_MARKERS is not set
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -102,7 +114,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -194,9 +206,9 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 # CONFIG_PHYS_ADDR_T_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 
 #
 # Exectuable file formats
@@ -262,6 +274,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -325,7 +338,6 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_ATA is not set
 # CONFIG_MD is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -344,7 +356,7 @@ CONFIG_NET_ETHERNET=y
 # CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
-# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_NETDEV_1000=y
 CONFIG_NETDEV_10000=y
 
@@ -410,6 +422,11 @@ CONFIG_LEGACY_PTY_COUNT=256
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -418,12 +435,6 @@ CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_THERMAL is not set
 # CONFIG_THERMAL_HWMON is not set
 # CONFIG_WATCHDOG is not set
-CONFIG_SSB_POSSIBLE=y
-
-#
-# Sonics Silicon Backplane
-#
-# CONFIG_SSB is not set
 
 #
 # Multifunction device drivers
@@ -433,22 +444,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -469,9 +465,12 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_NEW_LEDS is not set
 # CONFIG_ACCESSIBILITY is not set
 # CONFIG_RTC_CLASS is not set
-# CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -485,12 +484,15 @@ CONFIG_EXT2_FS=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 # CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
 # CONFIG_QUOTA is not set
 # CONFIG_AUTOFS_FS is not set
 # CONFIG_AUTOFS4_FS is not set
@@ -678,6 +680,7 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_SYSCTL_SYSCALL_CHECK is not set
 # CONFIG_PAGE_POISONING is not set
 # CONFIG_SAMPLES is not set
+# CONFIG_KMEMCHECK is not set
 CONFIG_EARLY_PRINTK=y
 CONFIG_HEART_BEAT=y
 CONFIG_DEBUG_BOOTMEM=y
@@ -793,6 +796,5 @@ CONFIG_ZLIB_INFLATE=y
 CONFIG_DECOMPRESS_GZIP=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
diff --git a/arch/microblaze/configs/nommu_defconfig b/arch/microblaze/configs/nommu_defconfig
index 4ef6af0a8f3..8b638615a97 100644
--- a/arch/microblaze/configs/nommu_defconfig
+++ b/arch/microblaze/configs/nommu_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc5
-# Mon May 11 09:01:02 2009
+# Linux kernel version: 2.6.31-rc6
+# Tue Aug 18 10:35:30 2009
 #
 CONFIG_MICROBLAZE=y
 # CONFIG_SWAP is not set
@@ -17,9 +17,12 @@ CONFIG_GENERIC_TIME=y
 # CONFIG_GENERIC_TIME_VSYSCALL is not set
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_CSUM=y
 # CONFIG_PCI is not set
-# CONFIG_NO_DMA is not set
+CONFIG_NO_DMA=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -64,7 +67,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_HOTPLUG is not set
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -76,13 +78,23 @@ CONFIG_SIGNALFD=y
 CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_AIO=y
+
+#
+# Performance Counters
+#
 CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
 # CONFIG_SLOB is not set
 # CONFIG_PROFILING is not set
 # CONFIG_MARKERS is not set
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -95,7 +107,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -156,8 +168,16 @@ CONFIG_CMDLINE_BOOL=y
 CONFIG_CMDLINE="console=ttyUL0,115200"
 # CONFIG_CMDLINE_FORCE is not set
 CONFIG_OF=y
-CONFIG_OF_DEVICE=y
 CONFIG_PROC_DEVICETREE=y
+
+#
+# Advanced setup
+#
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_KERNEL_START=0x90000000
 CONFIG_SELECT_MEMORY_MODEL=y
 CONFIG_FLATMEM_MANUAL=y
 # CONFIG_DISCONTIGMEM_MANUAL is not set
@@ -169,7 +189,7 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 # CONFIG_PHYS_ADDR_T_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
 CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_NOMMU_INITIAL_TRIM_EXCESS=1
 
 #
@@ -237,6 +257,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -254,7 +275,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -353,6 +378,7 @@ CONFIG_MTD_UCLINUX=y
 # UBI - Unsorted block images
 #
 # CONFIG_MTD_UBI is not set
+CONFIG_OF_DEVICE=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
 # CONFIG_BLK_DEV_COW_COMMON is not set
@@ -364,6 +390,7 @@ CONFIG_BLK_DEV_RAM_SIZE=4096
 # CONFIG_BLK_DEV_XIP is not set
 # CONFIG_CDROM_PKTCDVD is not set
 # CONFIG_ATA_OVER_ETH is not set
+# CONFIG_XILINX_SYSACE is not set
 CONFIG_MISC_DEVICES=y
 # CONFIG_ENCLOSURE_SERVICES is not set
 # CONFIG_C2PORT is not set
@@ -383,7 +410,6 @@ CONFIG_MISC_DEVICES=y
 # CONFIG_ATA is not set
 # CONFIG_MD is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -402,7 +428,7 @@ CONFIG_NET_ETHERNET=y
 # CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
-# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_NETDEV_1000=y
 CONFIG_NETDEV_10000=y
 
@@ -463,23 +489,25 @@ CONFIG_HW_RANDOM=y
 # CONFIG_HW_RANDOM_TIMERIOMEM is not set
 # CONFIG_RTC is not set
 # CONFIG_GEN_RTC is not set
+# CONFIG_XILINX_HWICAP is not set
 # CONFIG_R3964 is not set
 # CONFIG_RAW_DRIVER is not set
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
+# CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
 # CONFIG_POWER_SUPPLY is not set
 # CONFIG_HWMON is not set
 # CONFIG_THERMAL is not set
 # CONFIG_THERMAL_HWMON is not set
 # CONFIG_WATCHDOG is not set
-CONFIG_SSB_POSSIBLE=y
-
-#
-# Sonics Silicon Backplane
-#
-# CONFIG_SSB is not set
 
 #
 # Multifunction device drivers
@@ -489,22 +517,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-CONFIG_DAB=y
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -520,9 +533,10 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y
 # CONFIG_DISPLAY_SUPPORT is not set
 # CONFIG_SOUND is not set
 CONFIG_USB_SUPPORT=y
-# CONFIG_USB_ARCH_HAS_HCD is not set
+CONFIG_USB_ARCH_HAS_HCD=y
 # CONFIG_USB_ARCH_HAS_OHCI is not set
 # CONFIG_USB_ARCH_HAS_EHCI is not set
+# CONFIG_USB is not set
 # CONFIG_USB_OTG_WHITELIST is not set
 # CONFIG_USB_OTG_BLACKLIST_HUB is not set
 
@@ -543,9 +557,12 @@ CONFIG_USB_SUPPORT=y
 # CONFIG_NEW_LEDS is not set
 # CONFIG_ACCESSIBILITY is not set
 # CONFIG_RTC_CLASS is not set
-# CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -558,12 +575,15 @@ CONFIG_EXT2_FS=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 # CONFIG_DNOTIFY is not set
 # CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
 # CONFIG_QUOTA is not set
 # CONFIG_AUTOFS_FS is not set
 # CONFIG_AUTOFS4_FS is not set
@@ -813,6 +833,5 @@ CONFIG_GENERIC_FIND_LAST_BIT=y
 CONFIG_ZLIB_INFLATE=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
 CONFIG_HAVE_LMB=y
 CONFIG_NLATTR=y
-- 
GitLab


From f738eb1b63edf664da1b4ac76895d988749b2f07 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Tue, 18 Aug 2009 11:32:24 +0200
Subject: [PATCH 0954/1153] perf_counter: Fix the PARISC build

PARISC does not build:

/home/mingo/tip/kernel/perf_counter.c: In function 'perf_counter_index':
/home/mingo/tip/kernel/perf_counter.c:2016: error: 'PERF_COUNTER_INDEX_OFFSET' undeclared (first use in this function)
/home/mingo/tip/kernel/perf_counter.c:2016: error: (Each undeclared identifier is reported only once
/home/mingo/tip/kernel/perf_counter.c:2016: error: for each function it appears in.)

As PERF_COUNTER_INDEX_OFFSET is not defined.

Now, we could define it in the architecture - but lets also provide
a core default of 0 (which happens to be what all but one
architecture uses at the moment).

Architectures that need a different index offset should set this
value in their asm/perf_counter.h files.

Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index b8fe7397b90..36f65e2b8b5 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -2019,6 +2019,10 @@ int perf_counter_task_disable(void)
 	return 0;
 }
 
+#ifndef PERF_COUNTER_INDEX_OFFSET
+# define PERF_COUNTER_INDEX_OFFSET 0
+#endif
+
 static int perf_counter_index(struct perf_counter *counter)
 {
 	if (counter->state != PERF_COUNTER_STATE_ACTIVE)
-- 
GitLab


From 15f3fa4e7f608c5ce19187b3b4a953222fdfa751 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Tue, 18 Aug 2009 13:52:28 +0200
Subject: [PATCH 0955/1153] perf annotate: Fix segmentation fault

Linus reported this perf annotate segfault:

        [torvalds@nehalem git]$ perf annotate unmap_vmas
        Segmentation fault

       	#0  map__clone (self=<value optimized out>) at builtin-annotate.c:236
       	#1  thread__fork (self=<value optimized out>) at builtin-annotate.c:372

The bug here was that builtin-annotate.c was a copy of
builtin-report.c and a threading related fix to builtin-report.c
didnt get propagated to builtin-annotate.c ...

Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-annotate.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/tools/perf/builtin-annotate.c b/tools/perf/builtin-annotate.c
index 1dba568e194..343e7b14bf0 100644
--- a/tools/perf/builtin-annotate.c
+++ b/tools/perf/builtin-annotate.c
@@ -980,6 +980,13 @@ process_fork_event(event_t *event, unsigned long offset, unsigned long head)
 		(void *)(long)(event->header.size),
 		event->fork.pid, event->fork.ppid);
 
+	/*
+	 * A thread clone will have the same PID for both
+	 * parent and child.
+	 */
+	if (thread == parent)
+		return 0;
+
 	if (!thread || !parent || thread__fork(thread, parent)) {
 		dprintf("problem processing PERF_EVENT_FORK, skipping event.\n");
 		return -1;
-- 
GitLab


From 69ab849439b506cd8dd2879527fdb64d95dd5211 Mon Sep 17 00:00:00 2001
From: Thomas Gleixner <tglx@linutronix.de>
Date: Mon, 17 Aug 2009 14:07:16 +0200
Subject: [PATCH 0956/1153] genirq: Wake up irq thread after action has been
 installed

The wake_up_process() of the new irq thread in __setup_irq() is too
early as the irqaction is not yet fully initialized especially
action->irq is not yet set. The interrupt thread might dereference the
wrong irq descriptor.

Move the wakeup after the action is installed and action->irq has been
set.

Reported-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Buesch <mb@bu3sch.de>
---
 kernel/irq/manage.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/kernel/irq/manage.c b/kernel/irq/manage.c
index d222515a5a0..0ec9ed83173 100644
--- a/kernel/irq/manage.c
+++ b/kernel/irq/manage.c
@@ -607,7 +607,6 @@ __setup_irq(unsigned int irq, struct irq_desc *desc, struct irqaction *new)
 		 */
 		get_task_struct(t);
 		new->thread = t;
-		wake_up_process(t);
 	}
 
 	/*
@@ -690,6 +689,7 @@ __setup_irq(unsigned int irq, struct irq_desc *desc, struct irqaction *new)
 				(int)(new->flags & IRQF_TRIGGER_MASK));
 	}
 
+	new->irq = irq;
 	*old_ptr = new;
 
 	/* Reset broken irq detection when installing new handler */
@@ -707,7 +707,13 @@ __setup_irq(unsigned int irq, struct irq_desc *desc, struct irqaction *new)
 
 	spin_unlock_irqrestore(&desc->lock, flags);
 
-	new->irq = irq;
+	/*
+	 * Strictly no need to wake it up, but hung_task complains
+	 * when no hard interrupt wakes the thread up.
+	 */
+	if (new->thread)
+		wake_up_process(new->thread);
+
 	register_irq_proc(irq, desc);
 	new->dir = NULL;
 	register_handler_proc(irq, new);
-- 
GitLab


From 78b89ecd731798f2fec8cc26ca90739253cec33c Mon Sep 17 00:00:00 2001
From: Jan Beulich <JBeulich@novell.com>
Date: Tue, 18 Aug 2009 16:41:33 +0100
Subject: [PATCH 0957/1153] i386: Fix section mismatches for init code with
 !HOTPLUG_CPU

Commit 0e83815be719d3391bf5ea24b7fe696c07dbd417 changed the
section the initial_code variable gets allocated in, in an
attempt to address a section conflict warning. This, however
created a new section conflict when building without
HOTPLUG_CPU. The apparently only (reasonable) way to address
this is to always use __REFDATA.

Once at it, also fix a second section mismatch when not using
HOTPLUG_CPU.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <4A8AE7CD020000780001054B@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/head_32.S | 8 +-------
 1 file changed, 1 insertion(+), 7 deletions(-)

diff --git a/arch/x86/kernel/head_32.S b/arch/x86/kernel/head_32.S
index 0d98a01cbdb..cc827ac9e8d 100644
--- a/arch/x86/kernel/head_32.S
+++ b/arch/x86/kernel/head_32.S
@@ -261,9 +261,7 @@ page_pde_offset = (__PAGE_OFFSET >> 20);
  * which will be freed later
  */
 
-#ifndef CONFIG_HOTPLUG_CPU
-.section .init.text,"ax",@progbits
-#endif
+__CPUINIT
 
 #ifdef CONFIG_SMP
 ENTRY(startup_32_smp)
@@ -602,11 +600,7 @@ ignore_int:
 #endif
 	iret
 
-#ifndef CONFIG_HOTPLUG_CPU
-	__CPUINITDATA
-#else
 	__REFDATA
-#endif
 .align 4
 ENTRY(initial_code)
 	.long i386_start_kernel
-- 
GitLab


From b395cd8a74b4a8d943dd4b5585e676f62f7350b3 Mon Sep 17 00:00:00 2001
From: Kyle McMartin <kyle@redhat.com>
Date: Tue, 18 Aug 2009 12:41:25 -0400
Subject: [PATCH 0958/1153] perf tools: Make 'make html' work

pushd tools/perf/Documentation
make html
popd

is failing for me...

    ASCIIDOC perf-annotate.html
ERROR: unsafe: include file: /etc/asciidoc/./stylesheets/xhtml11.css
ERROR: unsafe: include file:
/etc/asciidoc/./stylesheets/xhtml11-manpage.css
ERROR: unsafe: include file:
/etc/asciidoc/./stylesheets/xhtml11-quirks.css
make: *** [perf-annotate.html] Error 1

Apparently asciidoc "unsafe" is the default mode of operation
in practice.

https://bugzilla.redhat.com/show_bug.cgi?id=506953

Works tidily now.

Signed-off-by: Kyle McMartin <kyle@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090818164125.GM25206@bombadil.infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/Documentation/Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/tools/perf/Documentation/Makefile b/tools/perf/Documentation/Makefile
index 5457192e1b4..bdd3b7ecad0 100644
--- a/tools/perf/Documentation/Makefile
+++ b/tools/perf/Documentation/Makefile
@@ -35,7 +35,7 @@ man7dir=$(mandir)/man7
 # DESTDIR=
 
 ASCIIDOC=asciidoc
-ASCIIDOC_EXTRA =
+ASCIIDOC_EXTRA = --unsafe
 MANPAGE_XSL = manpage-normal.xsl
 XMLTO_EXTRA =
 INSTALL?=install
-- 
GitLab


From a924586036833086b262a371b09d1266c23bb4d1 Mon Sep 17 00:00:00 2001
From: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Date: Wed, 19 Aug 2009 00:29:43 +0900
Subject: [PATCH 0959/1153] nilfs2: fix oopses with doubly mounted snapshots

will fix kernel oopses like the following:

 # mount -t nilfs2 -r -o cp=20 /dev/sdb1 /test1
 # mount -t nilfs2 -r -o cp=20 /dev/sdb1 /test2
 # umount /test1
 # umount /test2

BUG: sleeping function called from invalid context at arch/x86/mm/fault.c:1069
in_atomic(): 0, irqs_disabled(): 1, pid: 3886, name: umount.nilfs2
1 lock held by umount.nilfs2/3886:
 #0:  (&type->s_umount_key#31){+.+...}, at: [<c10b398a>] deactivate_super+0x52/0x6c
irq event stamp: 1219
hardirqs last  enabled at (1219): [<c135c774>] __mutex_unlock_slowpath+0xf8/0x119
hardirqs last disabled at (1218): [<c135c6d5>] __mutex_unlock_slowpath+0x59/0x119
softirqs last  enabled at (1214): [<c1033316>] __do_softirq+0x1a5/0x1ad
softirqs last disabled at (1205): [<c1033354>] do_softirq+0x36/0x5a
Pid: 3886, comm: umount.nilfs2 Not tainted 2.6.31-rc6 #55
Call Trace:
 [<c1023549>] __might_sleep+0x107/0x10e
 [<c13603c0>] do_page_fault+0x246/0x397
 [<c136017a>] ? do_page_fault+0x0/0x397
 [<c135e753>] error_code+0x6b/0x70
 [<c136017a>] ? do_page_fault+0x0/0x397
 [<c104f805>] ? __lock_acquire+0x91/0x12fd
 [<c1050a62>] ? __lock_acquire+0x12ee/0x12fd
 [<c1050a62>] ? __lock_acquire+0x12ee/0x12fd
 [<c1050b2b>] lock_acquire+0xba/0xdd
 [<d0d17d3f>] ? nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
 [<c135d4fe>] down_write+0x2a/0x46
 [<d0d17d3f>] ? nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
 [<d0d17d3f>] nilfs_detach_segment_constructor+0x2f/0x2fa [nilfs2]
 [<c104ea2c>] ? mark_held_locks+0x43/0x5b
 [<c104ecb1>] ? trace_hardirqs_on_caller+0x10b/0x133
 [<c104ece4>] ? trace_hardirqs_on+0xb/0xd
 [<d0d09ac1>] nilfs_put_super+0x2f/0xca [nilfs2]
 [<c10b3352>] generic_shutdown_super+0x49/0xb8
 [<c10b33de>] kill_block_super+0x1d/0x31
 [<c10e6599>] ? vfs_quota_off+0x0/0x12
 [<c10b398f>] deactivate_super+0x57/0x6c
 [<c10c4bc3>] mntput_no_expire+0x8c/0xb4
 [<c10c5094>] sys_umount+0x27f/0x2a4
 [<c10c50c6>] sys_oldumount+0xd/0xf
 [<c10031a4>] sysenter_do_call+0x12/0x38
 ...

This turns out to be a bug brought by an -rc1 patch ("nilfs2: simplify
remaining sget() use").

In the patch, a new "put resource" function, nilfs_put_sbinfo()
was introduced to delay freeing nilfs_sb_info struct.

But the nilfs_put_sbinfo() mistakenly used atomic_dec_and_test()
function to check the reference count, and it caused the nilfs_sb_info
was freed when user mounted a snapshot twice.

This bug also suggests there was unseen memory leak in usual mount
/umount operations for nilfs.

Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
---
 fs/nilfs2/the_nilfs.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/nilfs2/the_nilfs.h b/fs/nilfs2/the_nilfs.h
index e8adbffc626..1b9caafb866 100644
--- a/fs/nilfs2/the_nilfs.h
+++ b/fs/nilfs2/the_nilfs.h
@@ -253,7 +253,7 @@ nilfs_detach_writer(struct the_nilfs *nilfs, struct nilfs_sb_info *sbi)
 
 static inline void nilfs_put_sbinfo(struct nilfs_sb_info *sbi)
 {
-	if (!atomic_dec_and_test(&sbi->s_count))
+	if (atomic_dec_and_test(&sbi->s_count))
 		kfree(sbi);
 }
 
-- 
GitLab


From a58578e47f004017cf47803ad372490806630e58 Mon Sep 17 00:00:00 2001
From: Dave Jones <davej@redhat.com>
Date: Tue, 18 Aug 2009 13:47:37 -0400
Subject: [PATCH 0960/1153] security: Make LSM_MMAP_MIN_ADDR default match its
 help text.

Commit 788084aba2ab7348257597496befcbccabdc98a3 added the LSM_MMAP_MIN_ADDR
option, whose help text states "For most ia64, ppc64 and x86 users with lots
of address space a value of 65536 is reasonable and should cause no problems."
Which implies that it's default setting was typoed.

Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 security/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/security/Kconfig b/security/Kconfig
index 9c60c346a91..bba92689b56 100644
--- a/security/Kconfig
+++ b/security/Kconfig
@@ -116,7 +116,7 @@ config SECURITY_ROOTPLUG
 config LSM_MMAP_MIN_ADDR
 	int "Low address space for LSM to from user allocation"
 	depends on SECURITY && SECURITY_SELINUX
-	default 65535
+	default 65536
 	help
 	  This is the portion of low virtual memory which should be protected
 	  from userspace allocation.  Keeping a user from writing to low pages
-- 
GitLab


From 024e6cb408307de41cbfcb1e5a170d9af60ab2a9 Mon Sep 17 00:00:00 2001
From: Andreas Schwab <schwab@linux-m68k.org>
Date: Tue, 18 Aug 2009 22:14:29 +0200
Subject: [PATCH 0961/1153] security: Fix prompt for LSM_MMAP_MIN_ADDR

Fix prompt for LSM_MMAP_MIN_ADDR.

(Verbs are cool!)

Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 security/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/security/Kconfig b/security/Kconfig
index bba92689b56..4c865345caa 100644
--- a/security/Kconfig
+++ b/security/Kconfig
@@ -114,7 +114,7 @@ config SECURITY_ROOTPLUG
 	  If you are unsure how to answer this question, answer N.
 
 config LSM_MMAP_MIN_ADDR
-	int "Low address space for LSM to from user allocation"
+	int "Low address space for LSM to protect from user allocation"
 	depends on SECURITY && SECURITY_SELINUX
 	default 65536
 	help
-- 
GitLab


From 6b6f0b6c131321e1bc34c47b7f671b0360315402 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Tue, 18 Aug 2009 14:11:06 -0700
Subject: [PATCH 0962/1153] MAINTAINERS: OSD LIBRARY and FILESYSTEM pattern fix

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Benny Halevy <bhalevy@panasas.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 557d4dcc2c2..ac0fdfd2e50 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3809,7 +3809,7 @@ W:	http://open-osd.org
 T:	git git://git.open-osd.org/open-osd.git
 S:	Maintained
 F:	drivers/scsi/osd/
-F:	drivers/include/scsi/osd_*
+F:	include/scsi/osd_*
 F:	fs/exofs/
 
 P54 WIRELESS DRIVER
-- 
GitLab


From 89a4eb4b66e8f4d395e14a14d262dac4d6ca52f0 Mon Sep 17 00:00:00 2001
From: Jeff Layton <jlayton@redhat.com>
Date: Tue, 18 Aug 2009 14:11:08 -0700
Subject: [PATCH 0963/1153] vfs: make get_sb_pseudo set s_maxbytes to value
 that can be cast to signed

get_sb_pseudo sets s_maxbytes to ~0ULL which becomes negative when cast
to a signed value.  Fix it to use MAX_LFS_FILESIZE which casts properly
to a positive signed value.

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Steve French <smfrench@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/libfs.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/libfs.c b/fs/libfs.c
index ddfa89948c3..dcec3d3ea64 100644
--- a/fs/libfs.c
+++ b/fs/libfs.c
@@ -217,7 +217,7 @@ int get_sb_pseudo(struct file_system_type *fs_type, char *name,
 		return PTR_ERR(s);
 
 	s->s_flags = MS_NOUSER;
-	s->s_maxbytes = ~0ULL;
+	s->s_maxbytes = MAX_LFS_FILESIZE;
 	s->s_blocksize = PAGE_SIZE;
 	s->s_blocksize_bits = PAGE_SHIFT;
 	s->s_magic = magic;
-- 
GitLab


From 0753ba01e126020bf0f8150934903b48935b697d Mon Sep 17 00:00:00 2001
From: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Date: Tue, 18 Aug 2009 14:11:10 -0700
Subject: [PATCH 0964/1153] mm: revert "oom: move oom_adj value"

The commit 2ff05b2b (oom: move oom_adj value) moveed the oom_adj value to
the mm_struct.  It was a very good first step for sanitize OOM.

However Paul Menage reported the commit makes regression to his job
scheduler.  Current OOM logic can kill OOM_DISABLED process.

Why? His program has the code of similar to the following.

	...
	set_oom_adj(OOM_DISABLE); /* The job scheduler never killed by oom */
	...
	if (vfork() == 0) {
		set_oom_adj(0); /* Invoked child can be killed */
		execve("foo-bar-cmd");
	}
	....

vfork() parent and child are shared the same mm_struct.  then above
set_oom_adj(0) doesn't only change oom_adj for vfork() child, it's also
change oom_adj for vfork() parent.  Then, vfork() parent (job scheduler)
lost OOM immune and it was killed.

Actually, fork-setting-exec idiom is very frequently used in userland program.
We must not break this assumption.

Then, this patch revert commit 2ff05b2b and related commit.

Reverted commit list
---------------------
- commit 2ff05b2b4e (oom: move oom_adj value from task_struct to mm_struct)
- commit 4d8b9135c3 (oom: avoid unnecessary mm locking and scanning for OOM_DISABLE)
- commit 8123681022 (oom: only oom kill exiting tasks with attached memory)
- commit 933b787b57 (mm: copy over oom_adj value at fork time)

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 Documentation/filesystems/proc.txt | 15 +++----
 fs/proc/base.c                     | 19 ++-------
 include/linux/mm_types.h           |  2 -
 include/linux/sched.h              |  1 +
 kernel/fork.c                      |  1 -
 mm/oom_kill.c                      | 64 ++++++++++++++++++------------
 6 files changed, 48 insertions(+), 54 deletions(-)

diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt
index fad18f9456e..ffead13f944 100644
--- a/Documentation/filesystems/proc.txt
+++ b/Documentation/filesystems/proc.txt
@@ -1167,13 +1167,11 @@ CHAPTER 3: PER-PROCESS PARAMETERS
 3.1 /proc/<pid>/oom_adj - Adjust the oom-killer score
 ------------------------------------------------------
 
-This file can be used to adjust the score used to select which processes should
-be killed in an out-of-memory situation.  The oom_adj value is a characteristic
-of the task's mm, so all threads that share an mm with pid will have the same
-oom_adj value.  A high value will increase the likelihood of this process being
-killed by the oom-killer.  Valid values are in the range -16 to +15 as
-explained below and a special value of -17, which disables oom-killing
-altogether for threads sharing pid's mm.
+This file can be used to adjust the score used to select which processes
+should be killed in an  out-of-memory  situation.  Giving it a high score will
+increase the likelihood of this process being killed by the oom-killer.  Valid
+values are in the range -16 to +15, plus the special value -17, which disables
+oom-killing altogether for this process.
 
 The process to be killed in an out-of-memory situation is selected among all others
 based on its badness score. This value equals the original memory size of the process
@@ -1187,9 +1185,6 @@ the parent's score if they do not share the same memory. Thus forking servers
 are the prime candidates to be killed. Having only one 'hungry' child will make
 parent less preferable than the child.
 
-/proc/<pid>/oom_adj cannot be changed for kthreads since they are immune from
-oom-killing already.
-
 /proc/<pid>/oom_score shows process' current badness score.
 
 The following heuristics are then applied:
diff --git a/fs/proc/base.c b/fs/proc/base.c
index 175db258942..6f742f6658a 100644
--- a/fs/proc/base.c
+++ b/fs/proc/base.c
@@ -1003,12 +1003,7 @@ static ssize_t oom_adjust_read(struct file *file, char __user *buf,
 
 	if (!task)
 		return -ESRCH;
-	task_lock(task);
-	if (task->mm)
-		oom_adjust = task->mm->oom_adj;
-	else
-		oom_adjust = OOM_DISABLE;
-	task_unlock(task);
+	oom_adjust = task->oomkilladj;
 	put_task_struct(task);
 
 	len = snprintf(buffer, sizeof(buffer), "%i\n", oom_adjust);
@@ -1037,19 +1032,11 @@ static ssize_t oom_adjust_write(struct file *file, const char __user *buf,
 	task = get_proc_task(file->f_path.dentry->d_inode);
 	if (!task)
 		return -ESRCH;
-	task_lock(task);
-	if (!task->mm) {
-		task_unlock(task);
-		put_task_struct(task);
-		return -EINVAL;
-	}
-	if (oom_adjust < task->mm->oom_adj && !capable(CAP_SYS_RESOURCE)) {
-		task_unlock(task);
+	if (oom_adjust < task->oomkilladj && !capable(CAP_SYS_RESOURCE)) {
 		put_task_struct(task);
 		return -EACCES;
 	}
-	task->mm->oom_adj = oom_adjust;
-	task_unlock(task);
+	task->oomkilladj = oom_adjust;
 	put_task_struct(task);
 	if (end - buffer == 0)
 		return -EIO;
diff --git a/include/linux/mm_types.h b/include/linux/mm_types.h
index 7acc8439d9b..0042090a4d7 100644
--- a/include/linux/mm_types.h
+++ b/include/linux/mm_types.h
@@ -240,8 +240,6 @@ struct mm_struct {
 
 	unsigned long saved_auxv[AT_VECTOR_SIZE]; /* for /proc/PID/auxv */
 
-	s8 oom_adj;	/* OOM kill score adjustment (bit shift) */
-
 	cpumask_t cpu_vm_mask;
 
 	/* Architecture-specific MM context */
diff --git a/include/linux/sched.h b/include/linux/sched.h
index 3ab08e4bb6b..0f1ea4a6695 100644
--- a/include/linux/sched.h
+++ b/include/linux/sched.h
@@ -1198,6 +1198,7 @@ struct task_struct {
 	 * a short time
 	 */
 	unsigned char fpu_counter;
+	s8 oomkilladj; /* OOM kill score adjustment (bit shift). */
 #ifdef CONFIG_BLK_DEV_IO_TRACE
 	unsigned int btrace_seq;
 #endif
diff --git a/kernel/fork.c b/kernel/fork.c
index 021e1138556..144326b7af5 100644
--- a/kernel/fork.c
+++ b/kernel/fork.c
@@ -426,7 +426,6 @@ static struct mm_struct * mm_init(struct mm_struct * mm, struct task_struct *p)
 	init_rwsem(&mm->mmap_sem);
 	INIT_LIST_HEAD(&mm->mmlist);
 	mm->flags = (current->mm) ? current->mm->flags : default_dump_filter;
-	mm->oom_adj = (current->mm) ? current->mm->oom_adj : 0;
 	mm->core_state = NULL;
 	mm->nr_ptes = 0;
 	set_mm_counter(mm, file_rss, 0);
diff --git a/mm/oom_kill.c b/mm/oom_kill.c
index 175a67a78a9..a7b2460e922 100644
--- a/mm/oom_kill.c
+++ b/mm/oom_kill.c
@@ -58,7 +58,6 @@ unsigned long badness(struct task_struct *p, unsigned long uptime)
 	unsigned long points, cpu_time, run_time;
 	struct mm_struct *mm;
 	struct task_struct *child;
-	int oom_adj;
 
 	task_lock(p);
 	mm = p->mm;
@@ -66,11 +65,6 @@ unsigned long badness(struct task_struct *p, unsigned long uptime)
 		task_unlock(p);
 		return 0;
 	}
-	oom_adj = mm->oom_adj;
-	if (oom_adj == OOM_DISABLE) {
-		task_unlock(p);
-		return 0;
-	}
 
 	/*
 	 * The memory size of the process is the basis for the badness.
@@ -154,15 +148,15 @@ unsigned long badness(struct task_struct *p, unsigned long uptime)
 		points /= 8;
 
 	/*
-	 * Adjust the score by oom_adj.
+	 * Adjust the score by oomkilladj.
 	 */
-	if (oom_adj) {
-		if (oom_adj > 0) {
+	if (p->oomkilladj) {
+		if (p->oomkilladj > 0) {
 			if (!points)
 				points = 1;
-			points <<= oom_adj;
+			points <<= p->oomkilladj;
 		} else
-			points >>= -(oom_adj);
+			points >>= -(p->oomkilladj);
 	}
 
 #ifdef DEBUG
@@ -257,8 +251,11 @@ static struct task_struct *select_bad_process(unsigned long *ppoints,
 			*ppoints = ULONG_MAX;
 		}
 
+		if (p->oomkilladj == OOM_DISABLE)
+			continue;
+
 		points = badness(p, uptime.tv_sec);
-		if (points > *ppoints) {
+		if (points > *ppoints || !chosen) {
 			chosen = p;
 			*ppoints = points;
 		}
@@ -307,7 +304,8 @@ static void dump_tasks(const struct mem_cgroup *mem)
 		}
 		printk(KERN_INFO "[%5d] %5d %5d %8lu %8lu %3d     %3d %s\n",
 		       p->pid, __task_cred(p)->uid, p->tgid, mm->total_vm,
-		       get_mm_rss(mm), (int)task_cpu(p), mm->oom_adj, p->comm);
+		       get_mm_rss(mm), (int)task_cpu(p), p->oomkilladj,
+		       p->comm);
 		task_unlock(p);
 	} while_each_thread(g, p);
 }
@@ -325,8 +323,11 @@ static void __oom_kill_task(struct task_struct *p, int verbose)
 		return;
 	}
 
-	if (!p->mm)
+	if (!p->mm) {
+		WARN_ON(1);
+		printk(KERN_WARNING "tried to kill an mm-less task!\n");
 		return;
+	}
 
 	if (verbose)
 		printk(KERN_ERR "Killed process %d (%s)\n",
@@ -348,13 +349,28 @@ static int oom_kill_task(struct task_struct *p)
 	struct mm_struct *mm;
 	struct task_struct *g, *q;
 
-	task_lock(p);
 	mm = p->mm;
-	if (!mm || mm->oom_adj == OOM_DISABLE) {
-		task_unlock(p);
+
+	/* WARNING: mm may not be dereferenced since we did not obtain its
+	 * value from get_task_mm(p).  This is OK since all we need to do is
+	 * compare mm to q->mm below.
+	 *
+	 * Furthermore, even if mm contains a non-NULL value, p->mm may
+	 * change to NULL at any time since we do not hold task_lock(p).
+	 * However, this is of no concern to us.
+	 */
+
+	if (mm == NULL)
 		return 1;
-	}
-	task_unlock(p);
+
+	/*
+	 * Don't kill the process if any threads are set to OOM_DISABLE
+	 */
+	do_each_thread(g, q) {
+		if (q->mm == mm && q->oomkilladj == OOM_DISABLE)
+			return 1;
+	} while_each_thread(g, q);
+
 	__oom_kill_task(p, 1);
 
 	/*
@@ -377,11 +393,10 @@ static int oom_kill_process(struct task_struct *p, gfp_t gfp_mask, int order,
 	struct task_struct *c;
 
 	if (printk_ratelimit()) {
-		task_lock(current);
 		printk(KERN_WARNING "%s invoked oom-killer: "
-			"gfp_mask=0x%x, order=%d, oom_adj=%d\n",
-			current->comm, gfp_mask, order,
-			current->mm ? current->mm->oom_adj : OOM_DISABLE);
+			"gfp_mask=0x%x, order=%d, oomkilladj=%d\n",
+			current->comm, gfp_mask, order, current->oomkilladj);
+		task_lock(current);
 		cpuset_print_task_mems_allowed(current);
 		task_unlock(current);
 		dump_stack();
@@ -394,9 +409,8 @@ static int oom_kill_process(struct task_struct *p, gfp_t gfp_mask, int order,
 	/*
 	 * If the task is already exiting, don't alarm the sysadmin or kill
 	 * its children or threads, just set TIF_MEMDIE so it can die quickly
-	 * if its mm is still attached.
 	 */
-	if (p->mm && (p->flags & PF_EXITING)) {
+	if (p->flags & PF_EXITING) {
 		__oom_kill_task(p, 0);
 		return 0;
 	}
-- 
GitLab


From b2503a9408e44eb0531adc3436c513ea70f91c42 Mon Sep 17 00:00:00 2001
From: Andrew Morton <akpm@linux-foundation.org>
Date: Tue, 18 Aug 2009 14:11:12 -0700
Subject: [PATCH 0965/1153] mmc: add the new linux-mmc mailing list to
 MAINTAINERS

There are a number of individual MMC drivers listed in MAINTAINERS.  I
didn't modify those records.  Perhaps I should have.

Cc: <linux-mmc@vger.kernel.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Pavel Pisa <ppisa@pikron.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Sascha Sommer <saschasommer@freenet.de>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index ac0fdfd2e50..60299a9a7ad 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3429,6 +3429,7 @@ F:	drivers/mfd/
 
 MULTIMEDIA CARD (MMC), SECURE DIGITAL (SD) AND SDIO SUBSYSTEM
 S:	Orphan
+L:	linux-mmc@vger.kernel.org
 F:	drivers/mmc/
 F:	include/linux/mmc/
 
-- 
GitLab


From b8978784544e8b4e8fbacb558df8580957d4f8a5 Mon Sep 17 00:00:00 2001
From: Ben Dooks <ben@simtec.co.uk>
Date: Tue, 18 Aug 2009 14:11:16 -0700
Subject: [PATCH 0966/1153] spi_s3c24xx: fix clock rate calculation

Currently the clock rate calculation may round as pleased, which means
that it is possible that we will round down and end up with a faster clock
rate than intended.

Change the calculation to use DIV_ROUND_UP() to ensure that we end up with
a clock rate either the same as or lower than the user requested one.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/spi/spi_s3c24xx.c | 17 +++++++----------
 1 file changed, 7 insertions(+), 10 deletions(-)

diff --git a/drivers/spi/spi_s3c24xx.c b/drivers/spi/spi_s3c24xx.c
index e0d44af4745..590be85c8f3 100644
--- a/drivers/spi/spi_s3c24xx.c
+++ b/drivers/spi/spi_s3c24xx.c
@@ -111,6 +111,7 @@ static int s3c24xx_spi_setupxfer(struct spi_device *spi,
 	unsigned int bpw;
 	unsigned int hz;
 	unsigned int div;
+	unsigned long clk;
 
 	bpw = t ? t->bits_per_word : spi->bits_per_word;
 	hz  = t ? t->speed_hz : spi->max_speed_hz;
@@ -120,20 +121,16 @@ static int s3c24xx_spi_setupxfer(struct spi_device *spi,
 		return -EINVAL;
 	}
 
-	div = clk_get_rate(hw->clk) / hz;
-
-	/* is clk = pclk / (2 * (pre+1)), or is it
-	 *    clk = (pclk * 2) / ( pre + 1) */
-
-	div /= 2;
-
-	if (div > 0)
-		div -= 1;
+	clk = clk_get_rate(hw->clk);
+	div = DIV_ROUND_UP(clk, hz * 2) - 1;
 
 	if (div > 255)
 		div = 255;
 
-	dev_dbg(&spi->dev, "setting pre-scaler to %d (hz %d)\n", div, hz);
+	dev_dbg(&spi->dev, "setting pre-scaler to %d (wanted %d, got %ld)\n",
+		div, hz, clk / (2 * (div + 1)));
+
+
 	writeb(div, hw->regs + S3C2410_SPPRE);
 
 	spin_lock(&hw->bitbang.lock);
-- 
GitLab


From 191529756633052680dd9d23ad63744ca5aa02a1 Mon Sep 17 00:00:00 2001
From: Ben Dooks <ben@simtec.co.uk>
Date: Tue, 18 Aug 2009 14:11:17 -0700
Subject: [PATCH 0967/1153] spi_s3c24xx: fix transfer setup code

Since the changes to the bitbang driver, there is the possibility we will
be called with either the speed_hz or bpw values zero.  We take these to
mean that the default values (8 bits per word, or maximum bus speed).

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/spi/spi_s3c24xx.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/spi/spi_s3c24xx.c b/drivers/spi/spi_s3c24xx.c
index 590be85c8f3..3f3119d760d 100644
--- a/drivers/spi/spi_s3c24xx.c
+++ b/drivers/spi/spi_s3c24xx.c
@@ -116,6 +116,12 @@ static int s3c24xx_spi_setupxfer(struct spi_device *spi,
 	bpw = t ? t->bits_per_word : spi->bits_per_word;
 	hz  = t ? t->speed_hz : spi->max_speed_hz;
 
+	if (!bpw)
+		bpw = 8;
+
+	if (!hz)
+		hz = spi->max_speed_hz;
+
 	if (bpw != 8) {
 		dev_err(&spi->dev, "invalid bits-per-word (%d)\n", bpw);
 		return -EINVAL;
-- 
GitLab


From 28d7a6ae92c099d81cbea08c20be0d2cf7ccd7ca Mon Sep 17 00:00:00 2001
From: Graff Yang <graff.yang@gmail.com>
Date: Tue, 18 Aug 2009 14:11:17 -0700
Subject: [PATCH 0968/1153] nommu: check fd read permission in
 validate_mmap_request()

According to the POSIX (1003.1-2008), the file descriptor shall have been
opened with read permission, regardless of the protection options specified to
mmap().  The ltp test cases mmap06/07 need this.

Signed-off-by: Graff Yang <graff.yang@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 mm/nommu.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/mm/nommu.c b/mm/nommu.c
index 28754c40be9..4bde489ec43 100644
--- a/mm/nommu.c
+++ b/mm/nommu.c
@@ -919,6 +919,10 @@ static int validate_mmap_request(struct file *file,
 		if (!file->f_op->read)
 			capabilities &= ~BDI_CAP_MAP_COPY;
 
+		/* The file shall have been opened with read permission. */
+		if (!(file->f_mode & FMODE_READ))
+			return -EACCES;
+
 		if (flags & MAP_SHARED) {
 			/* do checks for writing, appending and locking */
 			if ((prot & PROT_WRITE) &&
-- 
GitLab


From 503f7944fac68f4fdf71f8ebd06907f51eb64515 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Tue, 18 Aug 2009 14:11:18 -0700
Subject: [PATCH 0969/1153] REPORTING-BUGS: add get_maintainer.pl blurb

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 REPORTING-BUGS | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/REPORTING-BUGS b/REPORTING-BUGS
index ab0c56630a8..55a6074ccbb 100644
--- a/REPORTING-BUGS
+++ b/REPORTING-BUGS
@@ -15,7 +15,10 @@ worry too much about getting the wrong person. If you are unsure send it
 to the person responsible for the code relevant to what you were doing.
 If it occurs repeatably try and describe how to recreate it. That is
 worth even more than the oops itself.  The list of maintainers and
-mailing lists is in the MAINTAINERS file in this directory.
+mailing lists is in the MAINTAINERS file in this directory.  If you
+know the file name that causes the problem you can use the following
+command in this directory to find some of the maintainers of that file:
+     perl scripts/get_maintainer.pl -f <filename>
 
       If it is a security bug, please copy the Security Contact listed
 in the MAINTAINERS file.  They can help coordinate bugfix and disclosure.
-- 
GitLab


From 7f9cfb31030737a7fc9a1cbca3fd01bec184c849 Mon Sep 17 00:00:00 2001
From: Bo Liu <bo-liu@hotmail.com>
Date: Tue, 18 Aug 2009 14:11:19 -0700
Subject: [PATCH 0970/1153] mm: build_zonelists(): move clear node_load[] to
 __build_all_zonelists()

If node_load[] is cleared everytime build_zonelists() is
called,node_load[] will have no help to find the next node that should
appear in the given node's fallback list.

Because of the bug, zonelist's node_order is not calculated as expected.
This bug affects on big machine, which has asynmetric node distance.

[synmetric NUMA's node distance]
     0    1    2
0   10   12   12
1   12   10   12
2   12   12   10

[asynmetric NUMA's node distance]
     0    1    2
0   10   12   20
1   12   10   14
2   20   14   10

This (my bug) is very old but no one has reported this for a long time.
Maybe because the number of asynmetric NUMA is very small and they use
cpuset for customizing node memory allocation fallback.

[akpm@linux-foundation.org: fix CONFIG_NUMA=n build]
Signed-off-by: Bo Liu <bo-liu@hotmail.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 mm/page_alloc.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/mm/page_alloc.c b/mm/page_alloc.c
index d052abbe306..5cc986eb9f6 100644
--- a/mm/page_alloc.c
+++ b/mm/page_alloc.c
@@ -2544,7 +2544,6 @@ static void build_zonelists(pg_data_t *pgdat)
 	prev_node = local_node;
 	nodes_clear(used_mask);
 
-	memset(node_load, 0, sizeof(node_load));
 	memset(node_order, 0, sizeof(node_order));
 	j = 0;
 
@@ -2653,6 +2652,9 @@ static int __build_all_zonelists(void *dummy)
 {
 	int nid;
 
+#ifdef CONFIG_NUMA
+	memset(node_load, 0, sizeof(node_load));
+#endif
 	for_each_online_node(nid) {
 		pg_data_t *pgdat = NODE_DATA(nid);
 
-- 
GitLab


From eda1e328556565e211b7450250e40d6de751563a Mon Sep 17 00:00:00 2001
From: Jiri Olsa <jolsa@redhat.com>
Date: Tue, 11 Aug 2009 17:29:04 +0200
Subject: [PATCH 0971/1153] tracing: handle broken names in ftrace filter

If one filter item (for set_ftrace_filter and set_ftrace_notrace) is being
setup by more than 1 consecutive writes (FTRACE_ITER_CONT flag), it won't
be handled corretly.

I used following program to test/verify:

[snip]
#include <stdio.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <string.h>

int main(int argc, char **argv)
{
        int fd, i;
        char *file = argv[1];

        if (-1 == (fd = open(file, O_WRONLY))) {
                perror("open failed");
                return -1;
        }

        for(i = 0; i < (argc - 2); i++) {
                int len = strlen(argv[2+i]);
                int cnt, off = 0;

                while(len) {
                        cnt = write(fd, argv[2+i] + off, len);
                        len -= cnt;
                        off += cnt;
                }
        }

        close(fd);
        return 0;
}
[snip]

before change:
sh-4.0# echo > ./set_ftrace_filter
sh-4.0# /test ./set_ftrace_filter "sys" "_open "
sh-4.0# cat ./set_ftrace_filter
#### all functions enabled ####
sh-4.0#

after change:
sh-4.0# echo > ./set_ftrace_notrace
sh-4.0# test ./set_ftrace_notrace "sys" "_open "
sh-4.0# cat ./set_ftrace_notrace
sys_open
sh-4.0#

Signed-off-by: Jiri Olsa <jolsa@redhat.com>
LKML-Reference: <20090811152904.GA26065@jolsa.lab.eng.brq.redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
 kernel/trace/ftrace.c | 17 +++++++++++------
 1 file changed, 11 insertions(+), 6 deletions(-)

diff --git a/kernel/trace/ftrace.c b/kernel/trace/ftrace.c
index 1e1d23c2630..25edd5cc593 100644
--- a/kernel/trace/ftrace.c
+++ b/kernel/trace/ftrace.c
@@ -2278,7 +2278,11 @@ ftrace_regex_write(struct file *file, const char __user *ubuf,
 	read++;
 	cnt--;
 
-	if (!(iter->flags & ~FTRACE_ITER_CONT)) {
+	/*
+	 * If the parser haven't finished with the last write,
+	 * continue reading the user input without skipping spaces.
+	 */
+	if (!(iter->flags & FTRACE_ITER_CONT)) {
 		/* skip white space */
 		while (cnt && isspace(ch)) {
 			ret = get_user(ch, ubuf++);
@@ -2288,8 +2292,9 @@ ftrace_regex_write(struct file *file, const char __user *ubuf,
 			cnt--;
 		}
 
+		/* only spaces were written */
 		if (isspace(ch)) {
-			file->f_pos += read;
+			*ppos += read;
 			ret = read;
 			goto out;
 		}
@@ -2319,12 +2324,12 @@ ftrace_regex_write(struct file *file, const char __user *ubuf,
 		if (ret)
 			goto out;
 		iter->buffer_idx = 0;
-	} else
+	} else {
 		iter->flags |= FTRACE_ITER_CONT;
+		iter->buffer[iter->buffer_idx++] = ch;
+	}
 
-
-	file->f_pos += read;
-
+	*ppos += read;
 	ret = read;
  out:
 	mutex_unlock(&ftrace_regex_lock);
-- 
GitLab


From e2c6cbd9ace61039d3de39e717195e38f1492aee Mon Sep 17 00:00:00 2001
From: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Date: Tue, 18 Aug 2009 20:16:55 -0700
Subject: [PATCH 0972/1153] sparc: sys32.S incorrect compat-layer splice()
 system call

I think arch/sparc/kernel/sys32.S has an incorrect splice definition:

SIGN2(sys32_splice, sys_splice, %o0, %o1)

The splice() prototype looks like :

       long splice(int fd_in, loff_t *off_in, int fd_out,
                   loff_t *off_out, size_t len, unsigned int flags);

So I think we should have :

SIGN2(sys32_splice, sys_splice, %o0, %o2)

Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 arch/sparc/kernel/sys32.S | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/sparc/kernel/sys32.S b/arch/sparc/kernel/sys32.S
index 577f8fab8b6..aed94869ad6 100644
--- a/arch/sparc/kernel/sys32.S
+++ b/arch/sparc/kernel/sys32.S
@@ -134,7 +134,7 @@ SIGN1(sys32_getpeername, sys_getpeername, %o0)
 SIGN1(sys32_getsockname, sys_getsockname, %o0)
 SIGN2(sys32_ioprio_get, sys_ioprio_get, %o0, %o1)
 SIGN3(sys32_ioprio_set, sys_ioprio_set, %o0, %o1, %o2)
-SIGN2(sys32_splice, sys_splice, %o0, %o1)
+SIGN2(sys32_splice, sys_splice, %o0, %o2)
 SIGN2(sys32_sync_file_range, compat_sync_file_range, %o0, %o5)
 SIGN2(sys32_tee, sys_tee, %o0, %o1)
 SIGN1(sys32_vmsplice, compat_sys_vmsplice, %o0)
-- 
GitLab


From e7a5965a81a29a13cd4994fa23a6a7a1488bcdb6 Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Tue, 18 Aug 2009 20:21:40 -0700
Subject: [PATCH 0973/1153] yellowfin: Fix buffer underrun after
 dev_alloc_skb() failure

yellowfin_init_ring() needs to clean up if dev_alloc_skb() fails and
should pass an error status up to the caller. This also prevents an
buffer underrun if failure occurred in the first iteration.
yellowfin_open() which calls yellowfin_init_ring() should free its
requested irq upon failure.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/yellowfin.c | 28 ++++++++++++++++++----------
 1 file changed, 18 insertions(+), 10 deletions(-)

diff --git a/drivers/net/yellowfin.c b/drivers/net/yellowfin.c
index a07580138e8..c2fd6187773 100644
--- a/drivers/net/yellowfin.c
+++ b/drivers/net/yellowfin.c
@@ -346,7 +346,7 @@ static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
 static int yellowfin_open(struct net_device *dev);
 static void yellowfin_timer(unsigned long data);
 static void yellowfin_tx_timeout(struct net_device *dev);
-static void yellowfin_init_ring(struct net_device *dev);
+static int yellowfin_init_ring(struct net_device *dev);
 static int yellowfin_start_xmit(struct sk_buff *skb, struct net_device *dev);
 static irqreturn_t yellowfin_interrupt(int irq, void *dev_instance);
 static int yellowfin_rx(struct net_device *dev);
@@ -573,19 +573,24 @@ static int yellowfin_open(struct net_device *dev)
 {
 	struct yellowfin_private *yp = netdev_priv(dev);
 	void __iomem *ioaddr = yp->base;
-	int i;
+	int i, ret;
 
 	/* Reset the chip. */
 	iowrite32(0x80000000, ioaddr + DMACtrl);
 
-	i = request_irq(dev->irq, &yellowfin_interrupt, IRQF_SHARED, dev->name, dev);
-	if (i) return i;
+	ret = request_irq(dev->irq, &yellowfin_interrupt, IRQF_SHARED, dev->name, dev);
+	if (ret)
+		return ret;
 
 	if (yellowfin_debug > 1)
 		printk(KERN_DEBUG "%s: yellowfin_open() irq %d.\n",
 			   dev->name, dev->irq);
 
-	yellowfin_init_ring(dev);
+	ret = yellowfin_init_ring(dev);
+	if (ret) {
+		free_irq(dev->irq, dev);
+		return ret;
+	}
 
 	iowrite32(yp->rx_ring_dma, ioaddr + RxPtr);
 	iowrite32(yp->tx_ring_dma, ioaddr + TxPtr);
@@ -725,10 +730,10 @@ static void yellowfin_tx_timeout(struct net_device *dev)
 }
 
 /* Initialize the Rx and Tx rings, along with various 'dev' bits. */
-static void yellowfin_init_ring(struct net_device *dev)
+static int yellowfin_init_ring(struct net_device *dev)
 {
 	struct yellowfin_private *yp = netdev_priv(dev);
-	int i;
+	int i, j;
 
 	yp->tx_full = 0;
 	yp->cur_rx = yp->cur_tx = 0;
@@ -753,6 +758,11 @@ static void yellowfin_init_ring(struct net_device *dev)
 		yp->rx_ring[i].addr = cpu_to_le32(pci_map_single(yp->pci_dev,
 			skb->data, yp->rx_buf_sz, PCI_DMA_FROMDEVICE));
 	}
+	if (i != RX_RING_SIZE) {
+		for (j = 0; j < i; j++)
+			dev_kfree_skb(yp->rx_skbuff[j]);
+		return -ENOMEM;
+	}
 	yp->rx_ring[i-1].dbdma_cmd = cpu_to_le32(CMD_STOP);
 	yp->dirty_rx = (unsigned int)(i - RX_RING_SIZE);
 
@@ -769,8 +779,6 @@ static void yellowfin_init_ring(struct net_device *dev)
 	yp->tx_ring[--i].dbdma_cmd = cpu_to_le32(CMD_STOP | BRANCH_ALWAYS);
 #else
 {
-	int j;
-
 	/* Tx ring needs a pair of descriptors, the second for the status. */
 	for (i = 0; i < TX_RING_SIZE; i++) {
 		j = 2*i;
@@ -805,7 +813,7 @@ static void yellowfin_init_ring(struct net_device *dev)
 }
 #endif
 	yp->tx_tail_desc = &yp->tx_status[0];
-	return;
+	return 0;
 }
 
 static int yellowfin_start_xmit(struct sk_buff *skb, struct net_device *dev)
-- 
GitLab


From 80e6914db18e702549a15dea36fa7ace17f25c50 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Mon, 17 Aug 2009 10:22:37 +1000
Subject: [PATCH 0974/1153] drm/radeon/kms: although LVDS might be possible on
 crtc 1 don't do it.

LVDS always requests RMX_FULL, we need to fix it so that doesn't happen
before we can enable LVDS on crtc 1.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_legacy_encoders.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c
index 34d0f58eb94..9322675ef6d 100644
--- a/drivers/gpu/drm/radeon/radeon_legacy_encoders.c
+++ b/drivers/gpu/drm/radeon/radeon_legacy_encoders.c
@@ -1066,6 +1066,7 @@ radeon_add_legacy_encoder(struct drm_device *dev, uint32_t encoder_id, uint32_t
 
 	switch (radeon_encoder->encoder_id) {
 	case ENCODER_OBJECT_ID_INTERNAL_LVDS:
+		encoder->possible_crtcs = 0x1;
 		drm_encoder_init(dev, encoder, &radeon_legacy_lvds_enc_funcs, DRM_MODE_ENCODER_LVDS);
 		drm_encoder_helper_add(encoder, &radeon_legacy_lvds_helper_funcs);
 		if (rdev->is_atom_bios)
-- 
GitLab


From bf8e828b00a5b6a0fea16f452be578c060d57d64 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Mon, 17 Aug 2009 10:20:47 +1000
Subject: [PATCH 0975/1153] drm/radeon/kms: memset the allocated framebuffer
 before using it.

This gets rid of some ugliness, we shuold probably find a way
for the GPU to zero this.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_fb.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c
index 3206c0ad7b6..ec383edf5f3 100644
--- a/drivers/gpu/drm/radeon/radeon_fb.c
+++ b/drivers/gpu/drm/radeon/radeon_fb.c
@@ -574,6 +574,8 @@ int radeonfb_create(struct radeon_device *rdev,
 		goto out_unref;
 	}
 
+	memset_io(fbptr, 0, aligned_size);
+
 	strcpy(info->fix.id, "radeondrmfb");
 	info->fix.type = FB_TYPE_PACKED_PIXELS;
 	info->fix.visual = FB_VISUAL_TRUECOLOR;
-- 
GitLab


From 6a719e05330ef19acd9392dbbfb95a774776dee5 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Mon, 17 Aug 2009 10:19:51 +1000
Subject: [PATCH 0976/1153] drm/kms/radeon: cleanup combios TV table like DDX.

The fallback case wasn't getting executed properly if there
was no TV table, which my T42 M7 hasn't got.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_combios.c | 48 ++++++++++---------------
 1 file changed, 19 insertions(+), 29 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_combios.c b/drivers/gpu/drm/radeon/radeon_combios.c
index afc4db280b9..2a027e00762 100644
--- a/drivers/gpu/drm/radeon/radeon_combios.c
+++ b/drivers/gpu/drm/radeon/radeon_combios.c
@@ -685,23 +685,15 @@ static const uint32_t default_tvdac_adj[CHIP_LAST] = {
 	0x00780000,		/* rs480 */
 };
 
-static struct radeon_encoder_tv_dac
-    *radeon_legacy_get_tv_dac_info_from_table(struct radeon_device *rdev)
+static void radeon_legacy_get_tv_dac_info_from_table(struct radeon_device *rdev,
+						     struct radeon_encoder_tv_dac *tv_dac)
 {
-	struct radeon_encoder_tv_dac *tv_dac = NULL;
-
-	tv_dac = kzalloc(sizeof(struct radeon_encoder_tv_dac), GFP_KERNEL);
-
-	if (!tv_dac)
-		return NULL;
-
 	tv_dac->ps2_tvdac_adj = default_tvdac_adj[rdev->family];
 	if ((rdev->flags & RADEON_IS_MOBILITY) && (rdev->family == CHIP_RV250))
 		tv_dac->ps2_tvdac_adj = 0x00880000;
 	tv_dac->pal_tvdac_adj = tv_dac->ps2_tvdac_adj;
 	tv_dac->ntsc_tvdac_adj = tv_dac->ps2_tvdac_adj;
-
-	return tv_dac;
+	return;
 }
 
 struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct
@@ -713,19 +705,18 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct
 	uint16_t dac_info;
 	uint8_t rev, bg, dac;
 	struct radeon_encoder_tv_dac *tv_dac = NULL;
+	int found = 0;
+
+	tv_dac = kzalloc(sizeof(struct radeon_encoder_tv_dac), GFP_KERNEL);
+	if (!tv_dac)
+		return NULL;
 
 	if (rdev->bios == NULL)
-		return radeon_legacy_get_tv_dac_info_from_table(rdev);
+		goto out;
 
 	/* first check TV table */
 	dac_info = combios_get_table_offset(dev, COMBIOS_TV_INFO_TABLE);
 	if (dac_info) {
-		tv_dac =
-		    kzalloc(sizeof(struct radeon_encoder_tv_dac), GFP_KERNEL);
-
-		if (!tv_dac)
-			return NULL;
-
 		rev = RBIOS8(dac_info + 0x3);
 		if (rev > 4) {
 			bg = RBIOS8(dac_info + 0xc) & 0xf;
@@ -739,6 +730,7 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct
 			bg = RBIOS8(dac_info + 0x10) & 0xf;
 			dac = RBIOS8(dac_info + 0x11) & 0xf;
 			tv_dac->ntsc_tvdac_adj = (bg << 16) | (dac << 20);
+			found = 1;
 		} else if (rev > 1) {
 			bg = RBIOS8(dac_info + 0xc) & 0xf;
 			dac = (RBIOS8(dac_info + 0xc) >> 4) & 0xf;
@@ -751,22 +743,15 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct
 			bg = RBIOS8(dac_info + 0xe) & 0xf;
 			dac = (RBIOS8(dac_info + 0xe) >> 4) & 0xf;
 			tv_dac->ntsc_tvdac_adj = (bg << 16) | (dac << 20);
+			found = 1;
 		}
-
 		tv_dac->tv_std = radeon_combios_get_tv_info(encoder);
-
-	} else {
+	}
+	if (!found) {
 		/* then check CRT table */
 		dac_info =
 		    combios_get_table_offset(dev, COMBIOS_CRT_INFO_TABLE);
 		if (dac_info) {
-			tv_dac =
-			    kzalloc(sizeof(struct radeon_encoder_tv_dac),
-				    GFP_KERNEL);
-
-			if (!tv_dac)
-				return NULL;
-
 			rev = RBIOS8(dac_info) & 0x3;
 			if (rev < 2) {
 				bg = RBIOS8(dac_info + 0x3) & 0xf;
@@ -775,6 +760,7 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct
 				    (bg << 16) | (dac << 20);
 				tv_dac->pal_tvdac_adj = tv_dac->ps2_tvdac_adj;
 				tv_dac->ntsc_tvdac_adj = tv_dac->ps2_tvdac_adj;
+				found = 1;
 			} else {
 				bg = RBIOS8(dac_info + 0x4) & 0xf;
 				dac = RBIOS8(dac_info + 0x5) & 0xf;
@@ -782,13 +768,17 @@ struct radeon_encoder_tv_dac *radeon_combios_get_tv_dac_info(struct
 				    (bg << 16) | (dac << 20);
 				tv_dac->pal_tvdac_adj = tv_dac->ps2_tvdac_adj;
 				tv_dac->ntsc_tvdac_adj = tv_dac->ps2_tvdac_adj;
+				found = 1;
 			}
 		} else {
 			DRM_INFO("No TV DAC info found in BIOS\n");
-			return radeon_legacy_get_tv_dac_info_from_table(rdev);
 		}
 	}
 
+out:
+	if (!found) /* fallback to defaults */
+		radeon_legacy_get_tv_dac_info_from_table(rdev, tv_dac);
+
 	return tv_dac;
 }
 
-- 
GitLab


From 5ef5f72febfea420ce58f670bad83830a5e5e3de Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Mon, 17 Aug 2009 13:11:23 +1000
Subject: [PATCH 0977/1153] drm/kms: teardown crtc correctly when fb is
 destroyed.

If userspace destroys a framebuffer that is in use on a crtc,
don't just null it out, tear down the crtc properly so the
hw gets turned off.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/drm_crtc.c | 40 ++++++++++++--------------------------
 1 file changed, 12 insertions(+), 28 deletions(-)

diff --git a/drivers/gpu/drm/drm_crtc.c b/drivers/gpu/drm/drm_crtc.c
index 33be210d672..2f631c75f70 100644
--- a/drivers/gpu/drm/drm_crtc.c
+++ b/drivers/gpu/drm/drm_crtc.c
@@ -257,31 +257,6 @@ void *drm_mode_object_find(struct drm_device *dev, uint32_t id, uint32_t type)
 }
 EXPORT_SYMBOL(drm_mode_object_find);
 
-/**
- * drm_crtc_from_fb - find the CRTC structure associated with an fb
- * @dev: DRM device
- * @fb: framebuffer in question
- *
- * LOCKING:
- * Caller must hold mode_config lock.
- *
- * Find CRTC in the mode_config structure that matches @fb.
- *
- * RETURNS:
- * Pointer to the CRTC or NULL if it wasn't found.
- */
-struct drm_crtc *drm_crtc_from_fb(struct drm_device *dev,
-				  struct drm_framebuffer *fb)
-{
-	struct drm_crtc *crtc;
-
-	list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
-		if (crtc->fb == fb)
-			return crtc;
-	}
-	return NULL;
-}
-
 /**
  * drm_framebuffer_init - initialize a framebuffer
  * @dev: DRM device
@@ -328,11 +303,20 @@ void drm_framebuffer_cleanup(struct drm_framebuffer *fb)
 {
 	struct drm_device *dev = fb->dev;
 	struct drm_crtc *crtc;
+	struct drm_mode_set set;
+	int ret;
 
 	/* remove from any CRTC */
 	list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
-		if (crtc->fb == fb)
-			crtc->fb = NULL;
+		if (crtc->fb == fb) {
+			/* should turn off the crtc */
+			memset(&set, 0, sizeof(struct drm_mode_set));
+			set.crtc = crtc;
+			set.fb = NULL;
+			ret = crtc->funcs->set_config(&set);
+			if (ret)
+				DRM_ERROR("failed to reset crtc %p when fb was deleted\n", crtc);
+		}
 	}
 
 	drm_mode_object_put(dev, &fb->base);
@@ -1511,7 +1495,7 @@ int drm_mode_setcrtc(struct drm_device *dev, void *data,
 	set.mode = mode;
 	set.connectors = connector_set;
 	set.num_connectors = crtc_req->count_connectors;
-	set.fb =fb;
+	set.fb = fb;
 	ret = crtc->funcs->set_config(&set);
 
 out:
-- 
GitLab


From 456d8991a795ff5e44dbc1c2a7f8d5b4ed675866 Mon Sep 17 00:00:00 2001
From: Wan ZongShun <mcuos.com@gmail.com>
Date: Tue, 18 Aug 2009 23:34:58 -0700
Subject: [PATCH 0978/1153] net: Rename MAC platform driver for w90p910
 platform

Due to I modified the corresponding platform device name,
so I make the patch to rename MAC platform driver
for w90p910 platform.

Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/arm/w90p910_ether.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/arm/w90p910_ether.c b/drivers/net/arm/w90p910_ether.c
index 616fb7985a3..ddd231cb54b 100644
--- a/drivers/net/arm/w90p910_ether.c
+++ b/drivers/net/arm/w90p910_ether.c
@@ -1080,7 +1080,7 @@ static struct platform_driver w90p910_ether_driver = {
 	.probe		= w90p910_ether_probe,
 	.remove		= __devexit_p(w90p910_ether_remove),
 	.driver		= {
-		.name	= "w90p910-emc",
+		.name	= "nuc900-emc",
 		.owner	= THIS_MODULE,
 	},
 };
@@ -1101,5 +1101,5 @@ module_exit(w90p910_ether_exit);
 MODULE_AUTHOR("Wan ZongShun <mcuos.com@gmail.com>");
 MODULE_DESCRIPTION("w90p910 MAC driver!");
 MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:w90p910-emc");
+MODULE_ALIAS("platform:nuc900-emc");
 
-- 
GitLab


From a9919646d12a13bea7eb74b996686f900dffb120 Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Tue, 18 Aug 2009 23:44:08 -0700
Subject: [PATCH 0979/1153] sparc32: Kill trap table freeing code.

Normally, srmmu uses different trap table register values to allow
determination of the cpu we're on.  All of the trap tables have
identical content, they just sit at different offsets from the first
trap table, and the offset shifted down and masked out determines
the cpu we are on.

The code tries to free them up when they aren't actually used
(don't have all 4 cpus, we're on sun4d, etc.) but that causes
problems.

For one thing it triggers false positives in the DMA debugging
code.  And fixing that up while preserving this relative offset
thing isn't trivial.

So just kill the freeing code, it costs us at most 3 pages, big
deal...

Signed-off-by: David S. Miller <davem@davemloft.net>
---
 arch/sparc/kernel/sun4d_smp.c | 22 ----------------------
 arch/sparc/kernel/sun4m_smp.c | 26 --------------------------
 2 files changed, 48 deletions(-)

diff --git a/arch/sparc/kernel/sun4d_smp.c b/arch/sparc/kernel/sun4d_smp.c
index 54fb02468f0..68791cad7b7 100644
--- a/arch/sparc/kernel/sun4d_smp.c
+++ b/arch/sparc/kernel/sun4d_smp.c
@@ -162,9 +162,6 @@ extern void cpu_panic(void);
  */
  
 extern struct linux_prom_registers smp_penguin_ctable;
-extern unsigned long trapbase_cpu1[];
-extern unsigned long trapbase_cpu2[];
-extern unsigned long trapbase_cpu3[];
 
 void __init smp4d_boot_cpus(void)
 {
@@ -235,25 +232,6 @@ void __init smp4d_smp_done(void)
 	*prev = first;
 	local_flush_cache_all();
 
-	/* Free unneeded trap tables */
-	ClearPageReserved(virt_to_page(trapbase_cpu1));
-	init_page_count(virt_to_page(trapbase_cpu1));
-	free_page((unsigned long)trapbase_cpu1);
-	totalram_pages++;
-	num_physpages++;
-
-	ClearPageReserved(virt_to_page(trapbase_cpu2));
-	init_page_count(virt_to_page(trapbase_cpu2));
-	free_page((unsigned long)trapbase_cpu2);
-	totalram_pages++;
-	num_physpages++;
-
-	ClearPageReserved(virt_to_page(trapbase_cpu3));
-	init_page_count(virt_to_page(trapbase_cpu3));
-	free_page((unsigned long)trapbase_cpu3);
-	totalram_pages++;
-	num_physpages++;
-
 	/* Ok, they are spinning and ready to go. */
 	smp_processors_ready = 1;
 	sun4d_distribute_irqs();
diff --git a/arch/sparc/kernel/sun4m_smp.c b/arch/sparc/kernel/sun4m_smp.c
index 960b113d000..762d6eedd94 100644
--- a/arch/sparc/kernel/sun4m_smp.c
+++ b/arch/sparc/kernel/sun4m_smp.c
@@ -121,9 +121,6 @@ void __cpuinit smp4m_callin(void)
  */
  
 extern struct linux_prom_registers smp_penguin_ctable;
-extern unsigned long trapbase_cpu1[];
-extern unsigned long trapbase_cpu2[];
-extern unsigned long trapbase_cpu3[];
 
 void __init smp4m_boot_cpus(void)
 {
@@ -193,29 +190,6 @@ void __init smp4m_smp_done(void)
 	*prev = first;
 	local_flush_cache_all();
 
-	/* Free unneeded trap tables */
-	if (!cpu_isset(1, cpu_present_map)) {
-		ClearPageReserved(virt_to_page(trapbase_cpu1));
-		init_page_count(virt_to_page(trapbase_cpu1));
-		free_page((unsigned long)trapbase_cpu1);
-		totalram_pages++;
-		num_physpages++;
-	}
-	if (!cpu_isset(2, cpu_present_map)) {
-		ClearPageReserved(virt_to_page(trapbase_cpu2));
-		init_page_count(virt_to_page(trapbase_cpu2));
-		free_page((unsigned long)trapbase_cpu2);
-		totalram_pages++;
-		num_physpages++;
-	}
-	if (!cpu_isset(3, cpu_present_map)) {
-		ClearPageReserved(virt_to_page(trapbase_cpu3));
-		init_page_count(virt_to_page(trapbase_cpu3));
-		free_page((unsigned long)trapbase_cpu3);
-		totalram_pages++;
-		num_physpages++;
-	}
-
 	/* Ok, they are spinning and ready to go. */
 }
 
-- 
GitLab


From 2193aa276e2579d9c781c5269521d43f47da9959 Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Tue, 18 Aug 2009 23:46:12 -0700
Subject: [PATCH 0980/1153] sparc32: Update defconfig.

Signed-off-by: David S. Miller <davem@davemloft.net>
---
 arch/sparc/configs/sparc32_defconfig | 74 +++++++++++++++++-----------
 1 file changed, 44 insertions(+), 30 deletions(-)

diff --git a/arch/sparc/configs/sparc32_defconfig b/arch/sparc/configs/sparc32_defconfig
index 8bcd27af724..a0f62a808ed 100644
--- a/arch/sparc/configs/sparc32_defconfig
+++ b/arch/sparc/configs/sparc32_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc2
-# Fri Apr 17 04:04:46 2009
+# Linux kernel version: 2.6.31-rc1
+# Tue Aug 18 23:45:52 2009
 #
 # CONFIG_64BIT is not set
 CONFIG_SPARC=y
@@ -17,6 +17,7 @@ CONFIG_GENERIC_ISA_DMA=y
 CONFIG_ARCH_NO_VIRT_TO_BUS=y
 CONFIG_OF=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -74,7 +75,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -87,8 +87,13 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+
+#
+# Performance Counters
+#
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_COMPAT_BRK=y
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -97,6 +102,10 @@ CONFIG_SLAB=y
 # CONFIG_MARKERS is not set
 CONFIG_HAVE_OPROFILE=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
+
+#
+# GCOV-based kernel profiling
+#
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -109,7 +118,7 @@ CONFIG_MODULE_UNLOAD=y
 # CONFIG_MODVERSIONS is not set
 # CONFIG_MODULE_SRCVERSION_ALL is not set
 CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEV_INTEGRITY is not set
 
@@ -154,9 +163,9 @@ CONFIG_SPLIT_PTLOCK_CPUS=4
 # CONFIG_PHYS_ADDR_T_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_SUN_PM=y
 # CONFIG_SPARC_LED is not set
 CONFIG_SERIAL_CONSOLE=y
@@ -264,6 +273,7 @@ CONFIG_IPV6_TUNNEL=m
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -281,7 +291,11 @@ CONFIG_WIRELESS=y
 CONFIG_WIRELESS_OLD_REGULATORY=y
 # CONFIG_WIRELESS_EXT is not set
 # CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
@@ -335,6 +349,7 @@ CONFIG_MISC_DEVICES=y
 # EEPROM support
 #
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -358,10 +373,6 @@ CONFIG_BLK_DEV_SR=m
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 CONFIG_CHR_DEV_SG=m
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 # CONFIG_SCSI_MULTI_LUN is not set
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -379,6 +390,7 @@ CONFIG_SCSI_SPI_ATTRS=y
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
 # CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
@@ -387,6 +399,7 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_AIC7XXX_OLD is not set
 # CONFIG_SCSI_AIC79XX is not set
 # CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_ARCMSR is not set
 # CONFIG_MEGARAID_NEWGEN is not set
 # CONFIG_MEGARAID_LEGACY is not set
@@ -401,7 +414,6 @@ CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_SCSI_IPS is not set
 # CONFIG_SCSI_INITIO is not set
 # CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
 # CONFIG_SCSI_STEX is not set
 # CONFIG_SCSI_SYM53C8XX_2 is not set
 # CONFIG_SCSI_QLOGIC_1280 is not set
@@ -426,13 +438,16 @@ CONFIG_SCSI_SUNESP=y
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 CONFIG_DUMMY=m
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -463,6 +478,7 @@ CONFIG_SUNQE=m
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_NET_PCI is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 # CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
@@ -482,6 +498,7 @@ CONFIG_NETDEV_1000=y
 # CONFIG_VIA_VELOCITY is not set
 # CONFIG_TIGON3 is not set
 # CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -629,6 +646,11 @@ CONFIG_HW_RANDOM=m
 CONFIG_DEVPORT=y
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -668,22 +690,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -776,6 +783,10 @@ CONFIG_RTC_DRV_M48T59=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -799,10 +810,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -985,6 +998,7 @@ CONFIG_KGDB=y
 CONFIG_KGDB_SERIAL_CONSOLE=y
 CONFIG_KGDB_TESTS=y
 # CONFIG_KGDB_TESTS_ON_BOOT is not set
+# CONFIG_KMEMCHECK is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
 # CONFIG_STACK_DEBUG is not set
 
-- 
GitLab


From 1ca3976d8ca8b0b44145994b1433f759a642615b Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Tue, 18 Aug 2009 23:56:21 -0700
Subject: [PATCH 0981/1153] sparc64: Update defconfig.

Signed-off-by: David S. Miller <davem@davemloft.net>
---
 arch/sparc/configs/sparc64_defconfig | 59 ++++++++++++++++------------
 1 file changed, 34 insertions(+), 25 deletions(-)

diff --git a/arch/sparc/configs/sparc64_defconfig b/arch/sparc/configs/sparc64_defconfig
index 0123a4c596c..fdddf7a6f72 100644
--- a/arch/sparc/configs/sparc64_defconfig
+++ b/arch/sparc/configs/sparc64_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Tue Jun 16 04:59:36 2009
+# Linux kernel version: 2.6.31-rc1
+# Tue Aug 18 23:56:02 2009
 #
 CONFIG_64BIT=y
 CONFIG_SPARC=y
@@ -26,6 +26,7 @@ CONFIG_ARCH_NO_VIRT_TO_BUS=y
 CONFIG_OF=y
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -119,6 +120,11 @@ CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_USE_GENERIC_SMP_HELPERS=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -204,7 +210,6 @@ CONFIG_MIGRATION=y
 CONFIG_PHYS_ADDR_T_64BIT=y
 CONFIG_ZONE_DMA_FLAG=0
 CONFIG_NR_QUICK=1
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
 CONFIG_DEFAULT_MMAP_MIN_ADDR=8192
@@ -410,6 +415,7 @@ CONFIG_MISC_DEVICES=y
 #
 # CONFIG_EEPROM_AT24 is not set
 # CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
 # CONFIG_EEPROM_93CX6 is not set
 # CONFIG_CB710_CORE is not set
 CONFIG_HAVE_IDE=y
@@ -562,6 +568,7 @@ CONFIG_BLK_DEV_DM=m
 CONFIG_DM_CRYPT=m
 CONFIG_DM_SNAPSHOT=m
 CONFIG_DM_MIRROR=m
+# CONFIG_DM_LOG_USERSPACE is not set
 CONFIG_DM_ZERO=m
 # CONFIG_DM_MULTIPATH is not set
 # CONFIG_DM_DELAY is not set
@@ -573,7 +580,11 @@ CONFIG_DM_ZERO=m
 #
 
 #
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
 #
 # CONFIG_FIREWIRE is not set
 # CONFIG_IEEE1394 is not set
@@ -667,6 +678,7 @@ CONFIG_E1000E=m
 # CONFIG_VIA_VELOCITY is not set
 CONFIG_TIGON3=m
 CONFIG_BNX2=m
+# CONFIG_CNIC is not set
 # CONFIG_QLA3XXX is not set
 # CONFIG_ATL1 is not set
 # CONFIG_ATL1E is not set
@@ -773,6 +785,7 @@ CONFIG_MOUSE_SERIAL=y
 # CONFIG_MOUSE_APPLETOUCH is not set
 # CONFIG_MOUSE_BCM5974 is not set
 # CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_MOUSE_SYNAPTICS_I2C is not set
 # CONFIG_INPUT_JOYSTICK is not set
 # CONFIG_INPUT_TABLET is not set
 # CONFIG_INPUT_TOUCHSCREEN is not set
@@ -870,6 +883,7 @@ CONFIG_I2C_ALGOBIT=y
 #
 # I2C system bus drivers (mostly embedded / system-on-chip)
 #
+# CONFIG_I2C_DESIGNWARE is not set
 # CONFIG_I2C_OCORES is not set
 # CONFIG_I2C_SIMTEC is not set
 
@@ -898,13 +912,17 @@ CONFIG_I2C_ALGOBIT=y
 # CONFIG_SENSORS_PCF8574 is not set
 # CONFIG_PCF8575 is not set
 # CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
 # CONFIG_SENSORS_TSL2550 is not set
 # CONFIG_I2C_DEBUG_CORE is not set
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -959,6 +977,7 @@ CONFIG_HWMON=y
 # CONFIG_SENSORS_SMSC47B397 is not set
 # CONFIG_SENSORS_ADS7828 is not set
 # CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
 # CONFIG_SENSORS_VIA686A is not set
 # CONFIG_SENSORS_VT1211 is not set
 # CONFIG_SENSORS_VT8231 is not set
@@ -994,23 +1013,9 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
 # CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -1284,7 +1289,6 @@ CONFIG_USB=y
 #
 # Miscellaneous USB options
 #
-CONFIG_USB_DEVICEFS=y
 # CONFIG_USB_DEVICE_CLASS is not set
 # CONFIG_USB_DYNAMIC_MINORS is not set
 # CONFIG_USB_OTG is not set
@@ -1296,6 +1300,7 @@ CONFIG_USB_DEVICEFS=y
 # USB Host Controller Drivers
 #
 # CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
 CONFIG_USB_EHCI_HCD=m
 # CONFIG_USB_EHCI_ROOT_HUB_TT is not set
 # CONFIG_USB_EHCI_TT_NEWSCHED is not set
@@ -1374,7 +1379,6 @@ CONFIG_USB_STORAGE=m
 # CONFIG_USB_LD is not set
 # CONFIG_USB_TRANCEVIBRATOR is not set
 # CONFIG_USB_IOWARRIOR is not set
-# CONFIG_USB_TEST is not set
 # CONFIG_USB_ISIGHTFW is not set
 # CONFIG_USB_VST is not set
 # CONFIG_USB_GADGET is not set
@@ -1420,6 +1424,7 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
 # CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
 
 #
 # SPI RTC drivers
@@ -1448,6 +1453,10 @@ CONFIG_RTC_DRV_STARFIRE=y
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1480,11 +1489,11 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 CONFIG_FS_POSIX_ACL=y
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
 CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
@@ -1560,7 +1569,7 @@ CONFIG_NETWORK_FILESYSTEMS=y
 # CONFIG_PARTITION_ADVANCED is not set
 CONFIG_MSDOS_PARTITION=y
 CONFIG_SUN_PARTITION=y
-CONFIG_NLS=m
+CONFIG_NLS=y
 CONFIG_NLS_DEFAULT="iso8859-1"
 # CONFIG_NLS_CODEPAGE_437 is not set
 # CONFIG_NLS_CODEPAGE_737 is not set
-- 
GitLab


From 150fe14c1a1f08cb430d8382bf5554c2a168b79b Mon Sep 17 00:00:00 2001
From: Wu Fengguang <fengguang.wu@intel.com>
Date: Wed, 19 Aug 2009 16:58:59 +0800
Subject: [PATCH 0982/1153] ALSA: hda: enable speaker output for Compaq
 6530s/6531s

HP Compaq 6530s and 6531s internal speaker is silence or becomes silence
within 1 minute after fresh boot. It is found that pin 0x1c must be set to
PIN_OUT mode to make the speaker work. This is weird - line-in pin 0x1c and
speaker pin 0x16 seem to be unrelated.

The codec differences before/after patch are:

@@ Node 0x17 [Pin Complex] wcaps 0x40020b:
   Pin Default 0x41a6e130: [N/A] Mic at Ext Rear
     Conn = Digital, Color = White
     DefAssociation = 0x3, Sequence = 0x0
     Misc = NO_PRESENCE
-  Pin-ctls: 0x24: IN
+  Pin-ctls: 0x40: OUT
@@ Node 0x1c [Pin Complex] wcaps 0x40018d:
   Pin Default 0x41813021: [N/A] Line In at Ext Rear
     Conn = 1/8, Color = Blue
     DefAssociation = 0x2, Sequence = 0x1
-  Pin-ctls: 0x24: IN VREF_80
+  Pin-ctls: 0x40: OUT VREF_HIZ
   Unsolicited: tag=00, enabled=0
   Connection: 1
      0x24

Tests show that it won't impact (external) Mic recording.

Reported-by: "Lin, Ming M" <ming.m.lin@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/patch_analog.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/sound/pci/hda/patch_analog.c b/sound/pci/hda/patch_analog.c
index e8e6a43865c..f2bb4803417 100644
--- a/sound/pci/hda/patch_analog.c
+++ b/sound/pci/hda/patch_analog.c
@@ -3823,9 +3823,11 @@ static struct hda_verb ad1884a_laptop_verbs[] = {
 	/* Port-F (int speaker) mixer - route only from analog mixer */
 	{0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
 	{0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
-	/* Port-F pin */
-	{0x16, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
+	/* Port-F (int speaker) pin */
+	{0x16, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
 	{0x16, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE},
+	/* required for compaq 6530s/6531s speaker output */
+	{0x1c, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
 	/* Port-C pin - internal mic-in */
 	{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80},
 	{0x14, AC_VERB_SET_AMP_GAIN_MUTE, 0x7002}, /* raise mic as default */
-- 
GitLab


From ae709440edb2d36f51f5ea51cfab931f45c03e02 Mon Sep 17 00:00:00 2001
From: Wu Fengguang <fengguang.wu@intel.com>
Date: Wed, 19 Aug 2009 17:05:11 +0800
Subject: [PATCH 0983/1153] ALSA: hda: add model for Intel DG45ID/DG45FC boards

The BIOS pin configs are in fact correct and shall not be overwritten.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/patch_sigmatel.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c
index 456ef6ac12e..6990cfcb6a3 100644
--- a/sound/pci/hda/patch_sigmatel.c
+++ b/sound/pci/hda/patch_sigmatel.c
@@ -76,6 +76,7 @@ enum {
 	STAC_92HD73XX_AUTO,
 	STAC_92HD73XX_NO_JD, /* no jack-detection */
 	STAC_92HD73XX_REF,
+	STAC_92HD73XX_INTEL,
 	STAC_DELL_M6_AMIC,
 	STAC_DELL_M6_DMIC,
 	STAC_DELL_M6_BOTH,
@@ -1777,6 +1778,7 @@ static const char *stac92hd73xx_models[STAC_92HD73XX_MODELS] = {
 	[STAC_92HD73XX_AUTO] = "auto",
 	[STAC_92HD73XX_NO_JD] = "no-jd",
 	[STAC_92HD73XX_REF] = "ref",
+	[STAC_92HD73XX_INTEL] = "intel",
 	[STAC_DELL_M6_AMIC] = "dell-m6-amic",
 	[STAC_DELL_M6_DMIC] = "dell-m6-dmic",
 	[STAC_DELL_M6_BOTH] = "dell-m6",
@@ -1789,6 +1791,10 @@ static struct snd_pci_quirk stac92hd73xx_cfg_tbl[] = {
 				"DFI LanParty", STAC_92HD73XX_REF),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DFI, 0x3101,
 				"DFI LanParty", STAC_92HD73XX_REF),
+	SND_PCI_QUIRK(PCI_VENDOR_ID_INTEL, 0x5002,
+				"Intel DG45ID", STAC_92HD73XX_INTEL),
+	SND_PCI_QUIRK(PCI_VENDOR_ID_INTEL, 0x5003,
+				"Intel DG45FC", STAC_92HD73XX_INTEL),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x0254,
 				"Dell Studio 1535", STAC_DELL_M6_DMIC),
 	SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x0255,
-- 
GitLab


From fa6963b2481beff8b11f76006fbb63fdbbf2d2d7 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Wed, 19 Aug 2009 11:18:26 +0200
Subject: [PATCH 0984/1153] perf tools: Check perf.data owner

Add an owner check to opening perf.data files and a switch to
silence it.

Because perf-report/perf-annotate are binary parsers reading
another users' perf.data file could be a security risk if the
file were explicitly engineered to trigger bugs in the parser
(we hope of course there are non such bugs, but you never
know).

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090819092023.896648538@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 tools/perf/builtin-annotate.c | 7 +++++++
 tools/perf/builtin-report.c   | 7 +++++++
 2 files changed, 14 insertions(+)

diff --git a/tools/perf/builtin-annotate.c b/tools/perf/builtin-annotate.c
index 343e7b14bf0..5e17de984dc 100644
--- a/tools/perf/builtin-annotate.c
+++ b/tools/perf/builtin-annotate.c
@@ -31,6 +31,7 @@ static char		*vmlinux = "vmlinux";
 static char		default_sort_order[] = "comm,symbol";
 static char		*sort_order = default_sort_order;
 
+static int		force;
 static int		input;
 static int		show_mask = SHOW_KERNEL | SHOW_USER | SHOW_HV;
 
@@ -1334,6 +1335,11 @@ static int __cmd_annotate(void)
 		exit(-1);
 	}
 
+	if (!force && (stat.st_uid != geteuid())) {
+		fprintf(stderr, "file: %s not owned by current user\n", input_name);
+		exit(-1);
+	}
+
 	if (!stat.st_size) {
 		fprintf(stderr, "zero-sized file, nothing to do!\n");
 		exit(0);
@@ -1439,6 +1445,7 @@ static const struct option options[] = {
 		    "input file name"),
 	OPT_STRING('s', "symbol", &sym_hist_filter, "symbol",
 		    "symbol to annotate"),
+	OPT_BOOLEAN('f', "force", &force, "don't complain, do it"),
 	OPT_BOOLEAN('v', "verbose", &verbose,
 		    "be more verbose (show symbol address, etc)"),
 	OPT_BOOLEAN('D', "dump-raw-trace", &dump_trace,
diff --git a/tools/perf/builtin-report.c b/tools/perf/builtin-report.c
index b53a60fc12d..8b2ec882e6e 100644
--- a/tools/perf/builtin-report.c
+++ b/tools/perf/builtin-report.c
@@ -38,6 +38,7 @@ static char		*dso_list_str, *comm_list_str, *sym_list_str,
 static struct strlist	*dso_list, *comm_list, *sym_list;
 static char		*field_sep;
 
+static int		force;
 static int		input;
 static int		show_mask = SHOW_KERNEL | SHOW_USER | SHOW_HV;
 
@@ -1856,6 +1857,11 @@ static int __cmd_report(void)
 		exit(-1);
 	}
 
+	if (!force && (stat.st_uid != geteuid())) {
+		fprintf(stderr, "file: %s not owned by current user\n", input_name);
+		exit(-1);
+	}
+
 	if (!stat.st_size) {
 		fprintf(stderr, "zero-sized file, nothing to do!\n");
 		exit(0);
@@ -2064,6 +2070,7 @@ static const struct option options[] = {
 	OPT_BOOLEAN('D', "dump-raw-trace", &dump_trace,
 		    "dump raw trace in ASCII"),
 	OPT_STRING('k', "vmlinux", &vmlinux, "file", "vmlinux pathname"),
+	OPT_BOOLEAN('f', "force", &force, "don't complain, do it"),
 	OPT_BOOLEAN('m', "modules", &modules,
 		    "load module symbols - WARNING: use only with -k and LIVE kernel"),
 	OPT_BOOLEAN('n', "show-nr-samples", &show_nr_samples,
-- 
GitLab


From f833bab87fca5c3ce13778421b1365845843b976 Mon Sep 17 00:00:00 2001
From: Suresh Siddha <suresh.b.siddha@intel.com>
Date: Mon, 17 Aug 2009 14:34:59 -0700
Subject: [PATCH 0985/1153] clockevent: Prevent dead lock on clockevents_lock

Currently clockevents_notify() is called with interrupts enabled at
some places and interrupts disabled at some other places.

This results in a deadlock in this scenario.

cpu A holds clockevents_lock in clockevents_notify() with irqs enabled
cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled
cpu C doing set_mtrr() which will try to rendezvous of all the cpus.

This will result in C and A come to the rendezvous point and waiting
for B. B is stuck forever waiting for the spinlock and thus not
reaching the rendezvous point.

Fix the clockevents code so that clockevents_lock is taken with
interrupts disabled and thus avoid the above deadlock.

Also call lapic_timer_propagate_broadcast() on the destination cpu so
that we avoid calling smp_call_function() in the clockevents notifier
chain.

This issue left us wondering if we need to change the MTRR rendezvous
logic to use stop machine logic (instead of smp_call_function) or add
a check in spinlock debug code to see if there are other spinlocks
which gets taken under both interrupts enabled/disabled conditions.

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: "Brown Len" <len.brown@intel.com>
LKML-Reference: <1250544899.2709.210.camel@sbs-t61.sc.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
---
 arch/x86/kernel/process.c     |  6 +-----
 drivers/acpi/processor_idle.c |  6 ++++--
 kernel/time/clockevents.c     | 16 ++++++++++------
 kernel/time/tick-broadcast.c  |  7 +++----
 4 files changed, 18 insertions(+), 17 deletions(-)

diff --git a/arch/x86/kernel/process.c b/arch/x86/kernel/process.c
index 994dd6a4a2a..071166a4ba8 100644
--- a/arch/x86/kernel/process.c
+++ b/arch/x86/kernel/process.c
@@ -519,16 +519,12 @@ static void c1e_idle(void)
 		if (!cpumask_test_cpu(cpu, c1e_mask)) {
 			cpumask_set_cpu(cpu, c1e_mask);
 			/*
-			 * Force broadcast so ACPI can not interfere. Needs
-			 * to run with interrupts enabled as it uses
-			 * smp_function_call.
+			 * Force broadcast so ACPI can not interfere.
 			 */
-			local_irq_enable();
 			clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_FORCE,
 					   &cpu);
 			printk(KERN_INFO "Switch to broadcast mode on CPU%d\n",
 			       cpu);
-			local_irq_disable();
 		}
 		clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &cpu);
 
diff --git a/drivers/acpi/processor_idle.c b/drivers/acpi/processor_idle.c
index 0efa59e7e3a..66393d5c4c7 100644
--- a/drivers/acpi/processor_idle.c
+++ b/drivers/acpi/processor_idle.c
@@ -162,8 +162,9 @@ static void lapic_timer_check_state(int state, struct acpi_processor *pr,
 		pr->power.timer_broadcast_on_state = state;
 }
 
-static void lapic_timer_propagate_broadcast(struct acpi_processor *pr)
+static void lapic_timer_propagate_broadcast(void *arg)
 {
+	struct acpi_processor *pr = (struct acpi_processor *) arg;
 	unsigned long reason;
 
 	reason = pr->power.timer_broadcast_on_state < INT_MAX ?
@@ -635,7 +636,8 @@ static int acpi_processor_power_verify(struct acpi_processor *pr)
 		working++;
 	}
 
-	lapic_timer_propagate_broadcast(pr);
+	smp_call_function_single(pr->id, lapic_timer_propagate_broadcast,
+				 pr, 1);
 
 	return (working);
 }
diff --git a/kernel/time/clockevents.c b/kernel/time/clockevents.c
index a6dcd67b041..620b58abdc3 100644
--- a/kernel/time/clockevents.c
+++ b/kernel/time/clockevents.c
@@ -137,11 +137,12 @@ int clockevents_program_event(struct clock_event_device *dev, ktime_t expires,
  */
 int clockevents_register_notifier(struct notifier_block *nb)
 {
+	unsigned long flags;
 	int ret;
 
-	spin_lock(&clockevents_lock);
+	spin_lock_irqsave(&clockevents_lock, flags);
 	ret = raw_notifier_chain_register(&clockevents_chain, nb);
-	spin_unlock(&clockevents_lock);
+	spin_unlock_irqrestore(&clockevents_lock, flags);
 
 	return ret;
 }
@@ -178,16 +179,18 @@ static void clockevents_notify_released(void)
  */
 void clockevents_register_device(struct clock_event_device *dev)
 {
+	unsigned long flags;
+
 	BUG_ON(dev->mode != CLOCK_EVT_MODE_UNUSED);
 	BUG_ON(!dev->cpumask);
 
-	spin_lock(&clockevents_lock);
+	spin_lock_irqsave(&clockevents_lock, flags);
 
 	list_add(&dev->list, &clockevent_devices);
 	clockevents_do_notify(CLOCK_EVT_NOTIFY_ADD, dev);
 	clockevents_notify_released();
 
-	spin_unlock(&clockevents_lock);
+	spin_unlock_irqrestore(&clockevents_lock, flags);
 }
 EXPORT_SYMBOL_GPL(clockevents_register_device);
 
@@ -235,8 +238,9 @@ void clockevents_exchange_device(struct clock_event_device *old,
 void clockevents_notify(unsigned long reason, void *arg)
 {
 	struct list_head *node, *tmp;
+	unsigned long flags;
 
-	spin_lock(&clockevents_lock);
+	spin_lock_irqsave(&clockevents_lock, flags);
 	clockevents_do_notify(reason, arg);
 
 	switch (reason) {
@@ -251,7 +255,7 @@ void clockevents_notify(unsigned long reason, void *arg)
 	default:
 		break;
 	}
-	spin_unlock(&clockevents_lock);
+	spin_unlock_irqrestore(&clockevents_lock, flags);
 }
 EXPORT_SYMBOL_GPL(clockevents_notify);
 #endif
diff --git a/kernel/time/tick-broadcast.c b/kernel/time/tick-broadcast.c
index 877dbedc311..c2ec25087a3 100644
--- a/kernel/time/tick-broadcast.c
+++ b/kernel/time/tick-broadcast.c
@@ -205,11 +205,11 @@ static void tick_handle_periodic_broadcast(struct clock_event_device *dev)
  * Powerstate information: The system enters/leaves a state, where
  * affected devices might stop
  */
-static void tick_do_broadcast_on_off(void *why)
+static void tick_do_broadcast_on_off(unsigned long *reason)
 {
 	struct clock_event_device *bc, *dev;
 	struct tick_device *td;
-	unsigned long flags, *reason = why;
+	unsigned long flags;
 	int cpu, bc_stopped;
 
 	spin_lock_irqsave(&tick_broadcast_lock, flags);
@@ -276,8 +276,7 @@ void tick_broadcast_on_off(unsigned long reason, int *oncpu)
 		printk(KERN_ERR "tick-broadcast: ignoring broadcast for "
 		       "offline CPU #%d\n", *oncpu);
 	else
-		smp_call_function_single(*oncpu, tick_do_broadcast_on_off,
-					 &reason, 1);
+		tick_do_broadcast_on_off(&reason);
 }
 
 /*
-- 
GitLab


From 0dc9aa845c20ed1f46c85f229591b811dffc4b3b Mon Sep 17 00:00:00 2001
From: Anton Blanchard <anton@samba.org>
Date: Wed, 19 Aug 2009 16:10:16 +0100
Subject: [PATCH 0986/1153] AFS: Documentation updates

Fix some issues with the AFS documentation, found when testing AFS on ppc64:

- Update AFS features: reading/writing, local caching
- Typo in kafs sysfs debug file
- Use modprobe instead of insmod in example
- Update IPs for grand.central.org

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 Documentation/filesystems/afs.txt | 26 ++++++++++++--------------
 1 file changed, 12 insertions(+), 14 deletions(-)

diff --git a/Documentation/filesystems/afs.txt b/Documentation/filesystems/afs.txt
index 12ad6c7f4e5..ffef91c4e0d 100644
--- a/Documentation/filesystems/afs.txt
+++ b/Documentation/filesystems/afs.txt
@@ -23,15 +23,13 @@ it does support include:
 
  (*) Security (currently only AFS kaserver and KerberosIV tickets).
 
- (*) File reading.
+ (*) File reading and writing.
 
  (*) Automounting.
 
-It does not yet support the following AFS features:
-
- (*) Write support.
+ (*) Local caching (via fscache).
 
- (*) Local caching.
+It does not yet support the following AFS features:
 
  (*) pioctl() system call.
 
@@ -56,7 +54,7 @@ They permit the debugging messages to be turned on dynamically by manipulating
 the masks in the following files:
 
 	/sys/module/af_rxrpc/parameters/debug
-	/sys/module/afs/parameters/debug
+	/sys/module/kafs/parameters/debug
 
 
 =====
@@ -66,9 +64,9 @@ USAGE
 When inserting the driver modules the root cell must be specified along with a
 list of volume location server IP addresses:
 
-	insmod af_rxrpc.o
-	insmod rxkad.o
-	insmod kafs.o rootcell=cambridge.redhat.com:172.16.18.73:172.16.18.91
+	modprobe af_rxrpc
+	modprobe rxkad
+	modprobe kafs rootcell=cambridge.redhat.com:172.16.18.73:172.16.18.91
 
 The first module is the AF_RXRPC network protocol driver.  This provides the
 RxRPC remote operation protocol and may also be accessed from userspace.  See:
@@ -81,7 +79,7 @@ is the actual filesystem driver for the AFS filesystem.
 Once the module has been loaded, more modules can be added by the following
 procedure:
 
-	echo add grand.central.org 18.7.14.88:128.2.191.224 >/proc/fs/afs/cells
+	echo add grand.central.org 18.9.48.14:128.2.203.61:130.237.48.87 >/proc/fs/afs/cells
 
 Where the parameters to the "add" command are the name of a cell and a list of
 volume location servers within that cell, with the latter separated by colons.
@@ -101,7 +99,7 @@ The name of the volume can be suffixes with ".backup" or ".readonly" to
 specify connection to only volumes of those types.
 
 The name of the cell is optional, and if not given during a mount, then the
-named volume will be looked up in the cell specified during insmod.
+named volume will be looked up in the cell specified during modprobe.
 
 Additional cells can be added through /proc (see later section).
 
@@ -163,14 +161,14 @@ THE CELL DATABASE
 
 The filesystem maintains an internal database of all the cells it knows and the
 IP addresses of the volume location servers for those cells.  The cell to which
-the system belongs is added to the database when insmod is performed by the
+the system belongs is added to the database when modprobe is performed by the
 "rootcell=" argument or, if compiled in, using a "kafs.rootcell=" argument on
 the kernel command line.
 
 Further cells can be added by commands similar to the following:
 
 	echo add CELLNAME VLADDR[:VLADDR][:VLADDR]... >/proc/fs/afs/cells
-	echo add grand.central.org 18.7.14.88:128.2.191.224 >/proc/fs/afs/cells
+	echo add grand.central.org 18.9.48.14:128.2.203.61:130.237.48.87 >/proc/fs/afs/cells
 
 No other cell database operations are available at this time.
 
@@ -233,7 +231,7 @@ insmod /tmp/kafs.o rootcell=cambridge.redhat.com:172.16.18.91
 mount -t afs \%root.afs. /afs
 mount -t afs \%cambridge.redhat.com:root.cell. /afs/cambridge.redhat.com/
 
-echo add grand.central.org 18.7.14.88:128.2.191.224 > /proc/fs/afs/cells
+echo add grand.central.org 18.9.48.14:128.2.203.61:130.237.48.87 > /proc/fs/afs/cells
 mount -t afs "#grand.central.org:root.cell." /afs/grand.central.org/
 mount -t afs "#grand.central.org:root.archive." /afs/grand.central.org/archive
 mount -t afs "#grand.central.org:root.contrib." /afs/grand.central.org/contrib
-- 
GitLab


From 3abf2f3639959e4f53f209f93cd4d93fe9356de1 Mon Sep 17 00:00:00 2001
From: Takashi Iwai <tiwai@suse.de>
Date: Wed, 19 Aug 2009 20:05:02 +0200
Subject: [PATCH 0987/1153] ALSA: hda - Fix probe of Toshiba laptops with
 ALC268 codec

There are many variants of Toshiba laptops with ALC268 codec, and
it seems that a few of them don't work with model=toshiba preset
since they have the secondary ALC268 codec just for HDMI output.
This is a regression due to the previous clean-up work to merge all
Toshiba quirk entries into a single check.

This patch adds the identification of such laptops to apply the
standard BIOS-probing method.  Unfortunately, Toshiba laptops have
all the same PCI SSID, so we need to check the codec SSID to identify
each device.

Tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/patch_realtek.c | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)

diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index fea976793ae..6f683e451f2 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -12521,8 +12521,6 @@ static struct snd_pci_quirk alc268_cfg_tbl[] = {
 			   ALC268_TOSHIBA),
 	SND_PCI_QUIRK(0x1043, 0x1205, "ASUS W7J", ALC268_3ST),
 	SND_PCI_QUIRK(0x1170, 0x0040, "ZEPTO", ALC268_ZEPTO),
-	SND_PCI_QUIRK_MASK(0x1179, 0xff00, 0xff00, "TOSHIBA A/Lx05",
-			   ALC268_TOSHIBA),
 	SND_PCI_QUIRK(0x14c0, 0x0025, "COMPAL IFL90/JFL-92", ALC268_TOSHIBA),
 	SND_PCI_QUIRK(0x152d, 0x0763, "Diverse (CPR2000)", ALC268_ACER),
 	SND_PCI_QUIRK(0x152d, 0x0771, "Quanta IL1", ALC267_QUANTA_IL1),
@@ -12530,6 +12528,15 @@ static struct snd_pci_quirk alc268_cfg_tbl[] = {
 	{}
 };
 
+/* Toshiba laptops have no unique PCI SSID but only codec SSID */
+static struct snd_pci_quirk alc268_ssid_cfg_tbl[] = {
+	SND_PCI_QUIRK(0x1179, 0xff0a, "TOSHIBA X-200", ALC268_AUTO),
+	SND_PCI_QUIRK(0x1179, 0xff0e, "TOSHIBA X-200 HDMI", ALC268_AUTO),
+	SND_PCI_QUIRK_MASK(0x1179, 0xff00, 0xff00, "TOSHIBA A/Lx05",
+			   ALC268_TOSHIBA),
+	{}
+};
+
 static struct alc_config_preset alc268_presets[] = {
 	[ALC267_QUANTA_IL1] = {
 		.mixers = { alc267_quanta_il1_mixer, alc268_beep_mixer },
@@ -12696,6 +12703,10 @@ static int patch_alc268(struct hda_codec *codec)
 						  alc268_models,
 						  alc268_cfg_tbl);
 
+	if (board_config < 0 || board_config >= ALC268_MODEL_LAST)
+		board_config = snd_hda_check_board_codec_sid_config(codec,
+			ALC882_MODEL_LAST, alc268_models, alc268_ssid_cfg_tbl);
+
 	if (board_config < 0 || board_config >= ALC268_MODEL_LAST) {
 		printk(KERN_INFO "hda_codec: Unknown model for %s, "
 		       "trying auto-probe from BIOS...\n", codec->chip_name);
-- 
GitLab


From cbb35f8a2858f7e0fff5df598cb286c4bcae5976 Mon Sep 17 00:00:00 2001
From: Randy Dunlap <randy.dunlap@oracle.com>
Date: Wed, 19 Aug 2009 12:13:31 -0700
Subject: [PATCH 0988/1153] net: fix ks8851 build errors

Fix build errors due to missing Kconfig select of CRC32:

ks8851.c:(.text+0x7d2ee): undefined reference to `crc32_le'
ks8851.c:(.text+0x7d2f5): undefined reference to `bitrev32'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 5f6509a5f64..7a90e7ce5a9 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1733,6 +1733,7 @@ config KS8851
        tristate "Micrel KS8851 SPI"
        depends on SPI
        select MII
+	select CRC32
        help
          SPI driver for Micrel KS8851 SPI attached network chip.
 
-- 
GitLab


From 5416c2663517ebd0be0664c4d4ce3df0b116c059 Mon Sep 17 00:00:00 2001
From: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Date: Mon, 17 Aug 2009 12:25:41 -0700
Subject: [PATCH 0989/1153] x86: make sure load_percpu_segment has no
 stackprotector

load_percpu_segment() is used to set up the per-cpu segment registers,
which are also used for -fstack-protector.  Make sure that the
load_percpu_segment() function doesn't have stackprotector enabled.

[ Impact: allow percpu setup before calling stack-protected functions ]

Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
---
 arch/x86/kernel/cpu/Makefile | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/x86/kernel/cpu/Makefile b/arch/x86/kernel/cpu/Makefile
index 4e242f9a06e..8b5b9b625ed 100644
--- a/arch/x86/kernel/cpu/Makefile
+++ b/arch/x86/kernel/cpu/Makefile
@@ -7,6 +7,10 @@ ifdef CONFIG_FUNCTION_TRACER
 CFLAGS_REMOVE_common.o = -pg
 endif
 
+# Make sure load_percpu_segment has no stackprotector
+nostackp := $(call cc-option, -fno-stack-protector)
+CFLAGS_common.o		:= $(nostackp)
+
 obj-y			:= intel_cacheinfo.o addon_cpuid_features.o
 obj-y			+= proc.o capflags.o powerflags.o common.o
 obj-y			+= vmware.o hypervisor.o
-- 
GitLab


From ce2eef33d35cd7b932492b5a81fb0febd2b323cd Mon Sep 17 00:00:00 2001
From: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Date: Mon, 17 Aug 2009 12:26:53 -0700
Subject: [PATCH 0990/1153] xen: rearrange things to fix stackprotector

Make sure the stack-protector segment registers are properly set up
before calling any functions which may have stack-protection compiled
into them.

[ Impact: prevent Xen early-boot crash when stack-protector is enabled ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
---
 arch/x86/xen/Makefile    |  4 ++++
 arch/x86/xen/enlighten.c | 22 ++++++++++------------
 2 files changed, 14 insertions(+), 12 deletions(-)

diff --git a/arch/x86/xen/Makefile b/arch/x86/xen/Makefile
index 3b767d03fd6..a5b9288b7da 100644
--- a/arch/x86/xen/Makefile
+++ b/arch/x86/xen/Makefile
@@ -5,6 +5,10 @@ CFLAGS_REMOVE_time.o = -pg
 CFLAGS_REMOVE_irq.o = -pg
 endif
 
+# Make sure early boot has no stackprotector
+nostackp := $(call cc-option, -fno-stack-protector)
+CFLAGS_enlighten.o		:= $(nostackp)
+
 obj-y		:= enlighten.o setup.o multicalls.o mmu.o irq.o \
 			time.o xen-asm.o xen-asm_$(BITS).o \
 			grant-table.o suspend.o
diff --git a/arch/x86/xen/enlighten.c b/arch/x86/xen/enlighten.c
index f09e8c36ee8..edcf72a3c29 100644
--- a/arch/x86/xen/enlighten.c
+++ b/arch/x86/xen/enlighten.c
@@ -925,10 +925,6 @@ asmlinkage void __init xen_start_kernel(void)
 
 	xen_domain_type = XEN_PV_DOMAIN;
 
-	BUG_ON(memcmp(xen_start_info->magic, "xen-3", 5) != 0);
-
-	xen_setup_features();
-
 	/* Install Xen paravirt ops */
 	pv_info = xen_info;
 	pv_init_ops = xen_init_ops;
@@ -937,8 +933,15 @@ asmlinkage void __init xen_start_kernel(void)
 	pv_apic_ops = xen_apic_ops;
 	pv_mmu_ops = xen_mmu_ops;
 
-	xen_init_irq_ops();
+#ifdef CONFIG_X86_64
+	/*
+	 * Setup percpu state.  We only need to do this for 64-bit
+	 * because 32-bit already has %fs set properly.
+	 */
+	load_percpu_segment(0);
+#endif
 
+	xen_init_irq_ops();
 	xen_init_cpuid_mask();
 
 #ifdef CONFIG_X86_LOCAL_APIC
@@ -948,6 +951,8 @@ asmlinkage void __init xen_start_kernel(void)
 	set_xen_basic_apic_ops();
 #endif
 
+	xen_setup_features();
+
 	if (xen_feature(XENFEAT_mmu_pt_update_preserve_ad)) {
 		pv_mmu_ops.ptep_modify_prot_start = xen_ptep_modify_prot_start;
 		pv_mmu_ops.ptep_modify_prot_commit = xen_ptep_modify_prot_commit;
@@ -955,13 +960,6 @@ asmlinkage void __init xen_start_kernel(void)
 
 	machine_ops = xen_machine_ops;
 
-#ifdef CONFIG_X86_64
-	/*
-	 * Setup percpu state.  We only need to do this for 64-bit
-	 * because 32-bit already has %fs set properly.
-	 */
-	load_percpu_segment(0);
-#endif
 	/*
 	 * The only reliable way to retain the initial address of the
 	 * percpu gdt_page is to remember it here, so we can go and
-- 
GitLab


From 68947b8f9a36f7f7f54ca95e0c6e169bb603e803 Mon Sep 17 00:00:00 2001
From: Jiri Kosina <jkosina@suse.cz>
Date: Wed, 19 Aug 2009 22:07:44 -0700
Subject: [PATCH 0991/1153] Input: iforce - support new revision of ACT LABS
 Force RS

Reported-by: cemede@gmail.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
---
 drivers/input/joystick/iforce/iforce-main.c | 1 +
 drivers/input/joystick/iforce/iforce-usb.c  | 1 +
 2 files changed, 2 insertions(+)

diff --git a/drivers/input/joystick/iforce/iforce-main.c b/drivers/input/joystick/iforce/iforce-main.c
index baabf830264..f6c688cae33 100644
--- a/drivers/input/joystick/iforce/iforce-main.c
+++ b/drivers/input/joystick/iforce/iforce-main.c
@@ -74,6 +74,7 @@ static struct iforce_device iforce_device[] = {
 	{ 0x05ef, 0x8884, "AVB Mag Turbo Force",			btn_avb_wheel, abs_wheel, ff_iforce },
 	{ 0x05ef, 0x8888, "AVB Top Shot Force Feedback Racing Wheel",	btn_avb_tw, abs_wheel, ff_iforce }, //?
 	{ 0x061c, 0xc0a4, "ACT LABS Force RS",                          btn_wheel, abs_wheel, ff_iforce }, //?
+	{ 0x061c, 0xc084, "ACT LABS Force RS",				btn_wheel, abs_wheel, ff_iforce },
 	{ 0x06f8, 0x0001, "Guillemot Race Leader Force Feedback",	btn_wheel, abs_wheel, ff_iforce }, //?
 	{ 0x06f8, 0x0004, "Guillemot Force Feedback Racing Wheel",	btn_wheel, abs_wheel, ff_iforce }, //?
 	{ 0x06f8, 0x0004, "Gullemot Jet Leader 3D",			btn_joystick, abs_joystick, ff_iforce }, //?
diff --git a/drivers/input/joystick/iforce/iforce-usb.c b/drivers/input/joystick/iforce/iforce-usb.c
index f83185aeb51..9f289d8f52c 100644
--- a/drivers/input/joystick/iforce/iforce-usb.c
+++ b/drivers/input/joystick/iforce/iforce-usb.c
@@ -223,6 +223,7 @@ static struct usb_device_id iforce_usb_ids [] = {
 	{ USB_DEVICE(0x05ef, 0x8884) },		/* AVB Mag Turbo Force */
 	{ USB_DEVICE(0x05ef, 0x8888) },		/* AVB Top Shot FFB Racing Wheel */
 	{ USB_DEVICE(0x061c, 0xc0a4) },         /* ACT LABS Force RS */
+	{ USB_DEVICE(0x061c, 0xc084) },         /* ACT LABS Force RS */
 	{ USB_DEVICE(0x06f8, 0x0001) },		/* Guillemot Race Leader Force Feedback */
 	{ USB_DEVICE(0x06f8, 0x0004) },		/* Guillemot Force Feedback Racing Wheel */
 	{ USB_DEVICE(0x06f8, 0xa302) },		/* Guillemot Jet Leader 3D */
-- 
GitLab


From d3b325f9c25be6d504bc73afce7f92d0e25001d7 Mon Sep 17 00:00:00 2001
From: Petri Gynther <pgynther@google.com>
Date: Thu, 20 Aug 2009 02:21:27 -0700
Subject: [PATCH 0992/1153] ibm_newemac: emac_close() needs to call
 netif_carrier_off()

When ibm_newemac netdev instance is shutdown with "ifconfig down",
the netdev interface does not go properly down. netif_carrier_ok()
keeps returning TRUE even after "ifconfig down".

The problem can be seen when ibm_newemac instances are slaves of
a bonding interface. The bonding interface code uses netif_carrier_ok()
to determine the link status of its slaves. When ibm_newemac slave is
shutdown with "ifconfig down", the bonding interface won't detect any
link status change because netif_carrier_ok() keeps returning TRUE.

Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/ibm_newemac/core.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ibm_newemac/core.c b/drivers/net/ibm_newemac/core.c
index beb84213b67..f0f89080371 100644
--- a/drivers/net/ibm_newemac/core.c
+++ b/drivers/net/ibm_newemac/core.c
@@ -1305,6 +1305,8 @@ static int emac_close(struct net_device *ndev)
 
 	free_irq(dev->emac_irq, dev);
 
+	netif_carrier_off(ndev);
+
 	return 0;
 }
 
-- 
GitLab


From c82f63e411f1b58427c103bd95af2863b1c96dd1 Mon Sep 17 00:00:00 2001
From: Alek Du <alek.du@intel.com>
Date: Sat, 8 Aug 2009 08:46:19 +0800
Subject: [PATCH 0993/1153] PCI: check saved state before restore

Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.

Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.

Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
---
 drivers/pci/pci-driver.c | 2 +-
 drivers/pci/pci.c        | 2 ++
 2 files changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
index d76c4c85367..f99bc7f089f 100644
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -508,7 +508,7 @@ static int pci_restore_standard_config(struct pci_dev *pci_dev)
 			return error;
 	}
 
-	return pci_dev->state_saved ? pci_restore_state(pci_dev) : 0;
+	return pci_restore_state(pci_dev);
 }
 
 static void pci_pm_default_resume_noirq(struct pci_dev *pci_dev)
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index dbd0f947f49..7b70312181d 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -846,6 +846,8 @@ pci_restore_state(struct pci_dev *dev)
 	int i;
 	u32 val;
 
+	if (!dev->state_saved)
+		return 0;
 	/* PCI Express register must be restored first */
 	pci_restore_pcie_state(dev);
 
-- 
GitLab


From dcc4ec26942d3bae2c5a82ab8346ab53b540a171 Mon Sep 17 00:00:00 2001
From: Nishanth Menon <nm@ti.com>
Date: Thu, 20 Aug 2009 11:21:14 -0500
Subject: [PATCH 0994/1153] i2c-omap: Fix I2C status ACK

I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/i2c/busses/i2c-omap.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index d258b02aef4..94639d0aabd 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -674,7 +674,14 @@ omap_i2c_isr(int this_irq, void *dev_id)
 
 		err = 0;
 complete:
-		omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, stat);
+		/*
+		 * Ack the stat in one go, but [R/X]DR and [R/X]RDY should be
+		 * acked after the data operation is complete.
+		 * Ref: TRM SWPU114Q Figure 18-31
+		 */
+		omap_i2c_write_reg(dev, OMAP_I2C_STAT_REG, stat &
+				~(OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR |
+				OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR));
 
 		if (stat & OMAP_I2C_STAT_NACK) {
 			err |= OMAP_I2C_STAT_NACK;
-- 
GitLab


From dd11976aea15bde53ce40b076dd5fa462c74f41a Mon Sep 17 00:00:00 2001
From: Moiz Sonasath <m-sonasath@ti.com>
Date: Thu, 20 Aug 2009 11:21:15 -0500
Subject: [PATCH 0995/1153] i2c-omap: ACK pending [R/X]DR and [R/X]RDY
 interrupts

ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]

Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/i2c/busses/i2c-omap.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 94639d0aabd..16b39f470a7 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -694,6 +694,9 @@ complete:
 		}
 		if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK |
 					OMAP_I2C_STAT_AL)) {
+			omap_i2c_ack_stat(dev, stat &
+				(OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR |
+				OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR));
 			omap_i2c_complete_cmd(dev, err);
 			return IRQ_HANDLED;
 		}
-- 
GitLab


From 61149787d65b4a2f9c638d363dc65e13cb063e29 Mon Sep 17 00:00:00 2001
From: Moiz Sonasath <m-sonasath@ti.com>
Date: Thu, 20 Aug 2009 11:21:16 -0500
Subject: [PATCH 0996/1153] i2c-omap: Enable workaround for Errata 1.153 based
 on

Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.

The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type

Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/i2c/busses/i2c-omap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index 16b39f470a7..827da085813 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -784,7 +784,7 @@ complete:
 				 * memory to the I2C interface.
 				 */
 
-				if (cpu_is_omap34xx()) {
+				if (dev->rev <= OMAP_I2C_REV_ON_3430) {
 						while (!(stat & OMAP_I2C_STAT_XUDF)) {
 							if (stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) {
 								omap_i2c_ack_stat(dev, stat & (OMAP_I2C_STAT_XRDY | OMAP_I2C_STAT_XDR));
-- 
GitLab


From c37faafa7d46622b749437f7d294201a63af4beb Mon Sep 17 00:00:00 2001
From: Linus Walleij <linus.walleij@stericsson.com>
Date: Thu, 13 Aug 2009 22:14:23 +0200
Subject: [PATCH 0997/1153] i2c-stu300: I2C STU300 stability updates

- blk clk is enabled when an irq arrives. The clk should be enabled,
  but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
  has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
  downwards.
- Number of address send attempts before giving up is increased to 12
  from 10 since it most times take 8 tries before getting through.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/i2c/busses/i2c-stu300.c | 157 +++++++++++++++++++-------------
 1 file changed, 92 insertions(+), 65 deletions(-)

diff --git a/drivers/i2c/busses/i2c-stu300.c b/drivers/i2c/busses/i2c-stu300.c
index 182e711318b..d2728a28a8d 100644
--- a/drivers/i2c/busses/i2c-stu300.c
+++ b/drivers/i2c/busses/i2c-stu300.c
@@ -117,7 +117,8 @@ enum stu300_error {
 	STU300_ERROR_NONE = 0,
 	STU300_ERROR_ACKNOWLEDGE_FAILURE,
 	STU300_ERROR_BUS_ERROR,
-	STU300_ERROR_ARBITRATION_LOST
+	STU300_ERROR_ARBITRATION_LOST,
+	STU300_ERROR_UNKNOWN
 };
 
 /* timeout waiting for the controller to respond */
@@ -127,7 +128,7 @@ enum stu300_error {
  * The number of address send athemps tried before giving up.
  * If the first one failes it seems like 5 to 8 attempts are required.
  */
-#define NUM_ADDR_RESEND_ATTEMPTS 10
+#define NUM_ADDR_RESEND_ATTEMPTS 12
 
 /* I2C clock speed, in Hz 0-400kHz*/
 static unsigned int scl_frequency = 100000;
@@ -149,6 +150,7 @@ module_param(scl_frequency, uint,  0644);
  * @msg_index: index of current message
  * @msg_len: length of current message
  */
+
 struct stu300_dev {
 	struct platform_device	*pdev;
 	struct i2c_adapter	adapter;
@@ -188,6 +190,27 @@ static inline u32 stu300_r8(void __iomem *address)
 	return readl(address) & 0x000000FFU;
 }
 
+static void stu300_irq_enable(struct stu300_dev *dev)
+{
+	u32 val;
+	val = stu300_r8(dev->virtbase + I2C_CR);
+	val |= I2C_CR_INTERRUPT_ENABLE;
+	/* Twice paranoia (possible HW glitch) */
+	stu300_wr8(val, dev->virtbase + I2C_CR);
+	stu300_wr8(val, dev->virtbase + I2C_CR);
+}
+
+static void stu300_irq_disable(struct stu300_dev *dev)
+{
+	u32 val;
+	val = stu300_r8(dev->virtbase + I2C_CR);
+	val &= ~I2C_CR_INTERRUPT_ENABLE;
+	/* Twice paranoia (possible HW glitch) */
+	stu300_wr8(val, dev->virtbase + I2C_CR);
+	stu300_wr8(val, dev->virtbase + I2C_CR);
+}
+
+
 /*
  * Tells whether a certain event or events occurred in
  * response to a command. The events represent states in
@@ -196,9 +219,10 @@ static inline u32 stu300_r8(void __iomem *address)
  * documentation and can only be treated as abstract state
  * machine states.
  *
- * @ret 0 = event has not occurred, any other value means
- * the event occurred.
+ * @ret 0 = event has not occurred or unknown error, any
+ * other value means the correct event occurred or an error.
  */
+
 static int stu300_event_occurred(struct stu300_dev *dev,
 				   enum stu300_event mr_event) {
 	u32 status1;
@@ -206,11 +230,28 @@ static int stu300_event_occurred(struct stu300_dev *dev,
 
 	/* What event happened? */
 	status1 = stu300_r8(dev->virtbase + I2C_SR1);
+
 	if (!(status1 & I2C_SR1_EVF_IND))
 		/* No event at all */
 		return 0;
+
 	status2 = stu300_r8(dev->virtbase + I2C_SR2);
 
+	/* Block any multiple interrupts */
+	stu300_irq_disable(dev);
+
+	/* Check for errors first */
+	if (status2 & I2C_SR2_AF_IND) {
+		dev->cmd_err = STU300_ERROR_ACKNOWLEDGE_FAILURE;
+		return 1;
+	} else if (status2 & I2C_SR2_BERR_IND) {
+		dev->cmd_err = STU300_ERROR_BUS_ERROR;
+		return 1;
+	} else if (status2 & I2C_SR2_ARLO_IND) {
+		dev->cmd_err = STU300_ERROR_ARBITRATION_LOST;
+		return 1;
+	}
+
 	switch (mr_event) {
 	case STU300_EVENT_1:
 		if (status1 & I2C_SR1_ADSL_IND)
@@ -221,10 +262,6 @@ static int stu300_event_occurred(struct stu300_dev *dev,
 	case STU300_EVENT_7:
 	case STU300_EVENT_8:
 		if (status1 & I2C_SR1_BTF_IND) {
-			if (status2 & I2C_SR2_AF_IND)
-				dev->cmd_err = STU300_ERROR_ACKNOWLEDGE_FAILURE;
-			else if (status2 & I2C_SR2_BERR_IND)
-				dev->cmd_err = STU300_ERROR_BUS_ERROR;
 			return 1;
 		}
 		break;
@@ -240,8 +277,6 @@ static int stu300_event_occurred(struct stu300_dev *dev,
 	case STU300_EVENT_6:
 		if (status2 & I2C_SR2_ENDAD_IND) {
 			/* First check for any errors */
-			if (status2 & I2C_SR2_AF_IND)
-				dev->cmd_err = STU300_ERROR_ACKNOWLEDGE_FAILURE;
 			return 1;
 		}
 		break;
@@ -252,8 +287,15 @@ static int stu300_event_occurred(struct stu300_dev *dev,
 	default:
 		break;
 	}
-	if (status2 & I2C_SR2_ARLO_IND)
-		dev->cmd_err = STU300_ERROR_ARBITRATION_LOST;
+	/* If we get here, we're on thin ice.
+	 * Here we are in a status where we have
+	 * gotten a response that does not match
+	 * what we requested.
+	 */
+	dev->cmd_err = STU300_ERROR_UNKNOWN;
+	dev_err(&dev->pdev->dev,
+		"Unhandled interrupt! %d sr1: 0x%x sr2: 0x%x\n",
+		mr_event, status1, status2);
 	return 0;
 }
 
@@ -262,21 +304,20 @@ static irqreturn_t stu300_irh(int irq, void *data)
 	struct stu300_dev *dev = data;
 	int res;
 
+	/* Just make sure that the block is clocked */
+	clk_enable(dev->clk);
+
 	/* See if this was what we were waiting for */
 	spin_lock(&dev->cmd_issue_lock);
-	if (dev->cmd_event != STU300_EVENT_NONE) {
-		res = stu300_event_occurred(dev, dev->cmd_event);
-		if (res || dev->cmd_err != STU300_ERROR_NONE) {
-			u32 val;
-
-			complete(&dev->cmd_complete);
-			/* Block any multiple interrupts */
-			val = stu300_r8(dev->virtbase + I2C_CR);
-			val &= ~I2C_CR_INTERRUPT_ENABLE;
-			stu300_wr8(val, dev->virtbase + I2C_CR);
-		}
-	}
+
+	res = stu300_event_occurred(dev, dev->cmd_event);
+	if (res || dev->cmd_err != STU300_ERROR_NONE)
+		complete(&dev->cmd_complete);
+
 	spin_unlock(&dev->cmd_issue_lock);
+
+	clk_disable(dev->clk);
+
 	return IRQ_HANDLED;
 }
 
@@ -308,7 +349,6 @@ static int stu300_start_and_await_event(struct stu300_dev *dev,
 	stu300_wr8(cr_value, dev->virtbase + I2C_CR);
 	ret = wait_for_completion_interruptible_timeout(&dev->cmd_complete,
 							STU300_TIMEOUT);
-
 	if (ret < 0) {
 		dev_err(&dev->pdev->dev,
 		       "wait_for_completion_interruptible_timeout() "
@@ -342,7 +382,6 @@ static int stu300_await_event(struct stu300_dev *dev,
 				enum stu300_event mr_event)
 {
 	int ret;
-	u32 val;
 
 	if (unlikely(irqs_disabled())) {
 		/* TODO: implement polling for this case if need be. */
@@ -354,36 +393,18 @@ static int stu300_await_event(struct stu300_dev *dev,
 	/* Is it already here? */
 	spin_lock_irq(&dev->cmd_issue_lock);
 	dev->cmd_err = STU300_ERROR_NONE;
-	if (stu300_event_occurred(dev, mr_event)) {
-		spin_unlock_irq(&dev->cmd_issue_lock);
-		goto exit_await_check_err;
-	}
-	init_completion(&dev->cmd_complete);
-	dev->cmd_err = STU300_ERROR_NONE;
 	dev->cmd_event = mr_event;
 
-	/* Turn on the I2C interrupt for current operation */
-	val = stu300_r8(dev->virtbase + I2C_CR);
-	val |= I2C_CR_INTERRUPT_ENABLE;
-	stu300_wr8(val, dev->virtbase + I2C_CR);
-
-	/* Twice paranoia (possible HW glitch) */
-	stu300_wr8(val, dev->virtbase + I2C_CR);
+	init_completion(&dev->cmd_complete);
 
-	/* Check again: is it already here? */
-	if (unlikely(stu300_event_occurred(dev, mr_event))) {
-		/* Disable IRQ again. */
-		val &= ~I2C_CR_INTERRUPT_ENABLE;
-		stu300_wr8(val, dev->virtbase + I2C_CR);
-		spin_unlock_irq(&dev->cmd_issue_lock);
-		goto exit_await_check_err;
-	}
+	/* Turn on the I2C interrupt for current operation */
+	stu300_irq_enable(dev);
 
 	/* Unlock the command block and wait for the event to occur */
 	spin_unlock_irq(&dev->cmd_issue_lock);
+
 	ret = wait_for_completion_interruptible_timeout(&dev->cmd_complete,
 							STU300_TIMEOUT);
-
 	if (ret < 0) {
 		dev_err(&dev->pdev->dev,
 		       "wait_for_completion_interruptible_timeout()"
@@ -401,7 +422,6 @@ static int stu300_await_event(struct stu300_dev *dev,
 		return -ETIMEDOUT;
 	}
 
- exit_await_check_err:
 	if (dev->cmd_err != STU300_ERROR_NONE) {
 		if (mr_event != STU300_EVENT_6) {
 			dev_err(&dev->pdev->dev, "controller "
@@ -457,18 +477,19 @@ struct stu300_clkset {
 };
 
 static const struct stu300_clkset stu300_clktable[] = {
-	{ 0, 0xFFU },
-	{ 2500000, I2C_OAR2_FR_25_10MHZ },
-	{ 10000000, I2C_OAR2_FR_10_1667MHZ },
-	{ 16670000, I2C_OAR2_FR_1667_2667MHZ },
-	{ 26670000, I2C_OAR2_FR_2667_40MHZ },
-	{ 40000000, I2C_OAR2_FR_40_5333MHZ },
-	{ 53330000, I2C_OAR2_FR_5333_66MHZ },
-	{ 66000000, I2C_OAR2_FR_66_80MHZ },
-	{ 80000000, I2C_OAR2_FR_80_100MHZ },
+	{ 0,         0xFFU },
+	{ 2500000,   I2C_OAR2_FR_25_10MHZ },
+	{ 10000000,  I2C_OAR2_FR_10_1667MHZ },
+	{ 16670000,  I2C_OAR2_FR_1667_2667MHZ },
+	{ 26670000,  I2C_OAR2_FR_2667_40MHZ },
+	{ 40000000,  I2C_OAR2_FR_40_5333MHZ },
+	{ 53330000,  I2C_OAR2_FR_5333_66MHZ },
+	{ 66000000,  I2C_OAR2_FR_66_80MHZ },
+	{ 80000000,  I2C_OAR2_FR_80_100MHZ },
 	{ 100000000, 0xFFU },
 };
 
+
 static int stu300_set_clk(struct stu300_dev *dev, unsigned long clkrate)
 {
 
@@ -494,10 +515,10 @@ static int stu300_set_clk(struct stu300_dev *dev, unsigned long clkrate)
 
 	if (dev->speed > 100000)
 		/* Fast Mode I2C */
-		val = ((clkrate/dev->speed)-9)/3;
+		val = ((clkrate/dev->speed) - 9)/3 + 1;
 	else
 		/* Standard Mode I2C */
-		val = ((clkrate/dev->speed)-7)/2;
+		val = ((clkrate/dev->speed) - 7)/2 + 1;
 
 	/* According to spec the divider must be > 2 */
 	if (val < 0x002) {
@@ -557,6 +578,7 @@ static int stu300_init_hw(struct stu300_dev *dev)
 	 */
 	clkrate = clk_get_rate(dev->clk);
 	ret = stu300_set_clk(dev, clkrate);
+
 	if (ret)
 		return ret;
 	/*
@@ -641,7 +663,6 @@ static int stu300_xfer_msg(struct i2c_adapter *adap,
 	int attempts = 0;
 	struct stu300_dev *dev = i2c_get_adapdata(adap);
 
-
 	clk_enable(dev->clk);
 
 	/* Remove this if (0) to trace each and every message. */
@@ -715,14 +736,15 @@ static int stu300_xfer_msg(struct i2c_adapter *adap,
 
 	if (attempts < NUM_ADDR_RESEND_ATTEMPTS && attempts > 0) {
 		dev_dbg(&dev->pdev->dev, "managed to get address "
-		       "through after %d attempts\n", attempts);
+			"through after %d attempts\n", attempts);
 	} else if (attempts == NUM_ADDR_RESEND_ATTEMPTS) {
 		dev_dbg(&dev->pdev->dev, "I give up, tried %d times "
-		       "to resend address.\n",
-		       NUM_ADDR_RESEND_ATTEMPTS);
+			"to resend address.\n",
+			NUM_ADDR_RESEND_ATTEMPTS);
 		goto exit_disable;
 	}
 
+
 	if (msg->flags & I2C_M_RD) {
 		/* READ: we read the actual bytes one at a time */
 		for (i = 0; i < msg->len; i++) {
@@ -804,8 +826,10 @@ static int stu300_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
 {
 	int ret = -1;
 	int i;
+
 	struct stu300_dev *dev = i2c_get_adapdata(adap);
 	dev->msg_len = num;
+
 	for (i = 0; i < num; i++) {
 		/*
 		 * Another driver appears to send stop for each message,
@@ -817,6 +841,7 @@ static int stu300_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
 		dev->msg_index = i;
 
 		ret = stu300_xfer_msg(adap, &msgs[i], (i == (num - 1)));
+
 		if (ret != 0) {
 			num = ret;
 			break;
@@ -845,6 +870,7 @@ stu300_probe(struct platform_device *pdev)
 	struct resource *res;
 	int bus_nr;
 	int ret = 0;
+	char clk_name[] = "I2C0";
 
 	dev = kzalloc(sizeof(struct stu300_dev), GFP_KERNEL);
 	if (!dev) {
@@ -854,7 +880,8 @@ stu300_probe(struct platform_device *pdev)
 	}
 
 	bus_nr = pdev->id;
-	dev->clk = clk_get(&pdev->dev, NULL);
+	clk_name[3] += (char)bus_nr;
+	dev->clk = clk_get(&pdev->dev, clk_name);
 	if (IS_ERR(dev->clk)) {
 		ret = PTR_ERR(dev->clk);
 		dev_err(&pdev->dev, "could not retrieve i2c bus clock\n");
-- 
GitLab


From fc0ce23506d943b9eaa731a051769d0e0605eb03 Mon Sep 17 00:00:00 2001
From: Jan Beulich <JBeulich@novell.com>
Date: Thu, 20 Aug 2009 16:14:15 +0100
Subject: [PATCH 0998/1153] x86: add vmlinux.lds to targets in
 arch/x86/boot/compressed/Makefile

The absence of vmlinux.lds here keeps .vmlinux.lds.cmd from being
included, which in turn leads to it and all its dependents always
getting rebuilt independent of whether they are already up-to-date.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A8D84670200007800010D31@vpn.id2.novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
---
 arch/x86/boot/compressed/Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/boot/compressed/Makefile b/arch/x86/boot/compressed/Makefile
index e2ff504b4dd..f8ed0658404 100644
--- a/arch/x86/boot/compressed/Makefile
+++ b/arch/x86/boot/compressed/Makefile
@@ -4,7 +4,7 @@
 # create a compressed vmlinux image from the original vmlinux
 #
 
-targets := vmlinux vmlinux.bin vmlinux.bin.gz vmlinux.bin.bz2 vmlinux.bin.lzma head_$(BITS).o misc.o piggy.o
+targets := vmlinux.lds vmlinux vmlinux.bin vmlinux.bin.gz vmlinux.bin.bz2 vmlinux.bin.lzma head_$(BITS).o misc.o piggy.o
 
 KBUILD_CFLAGS := -m$(BITS) -D__KERNEL__ $(LINUX_INCLUDE) -O2
 KBUILD_CFLAGS += -fno-strict-aliasing -fPIC
-- 
GitLab


From a8b88d3d49623ac701b5dc996cbd61219c793c7c Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Thu, 20 Aug 2009 18:26:52 +0200
Subject: [PATCH 0999/1153] ocfs2: Add missing lock name

There is missing name for NFSSync cluster lock. This makes lockdep unhappy
because we end up passing NULL to lockdep when initializing lock key. Fix it.

Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/ocfs2_lockid.h | 1 +
 1 file changed, 1 insertion(+)

diff --git a/fs/ocfs2/ocfs2_lockid.h b/fs/ocfs2/ocfs2_lockid.h
index fcdba091af3..c212cf5a2bd 100644
--- a/fs/ocfs2/ocfs2_lockid.h
+++ b/fs/ocfs2/ocfs2_lockid.h
@@ -108,6 +108,7 @@ static char *ocfs2_lock_type_strings[] = {
 	[OCFS2_LOCK_TYPE_OPEN] = "Open",
 	[OCFS2_LOCK_TYPE_FLOCK] = "Flock",
 	[OCFS2_LOCK_TYPE_QINFO] = "Quota",
+	[OCFS2_LOCK_TYPE_NFS_SYNC] = "NFSSync",
 	[OCFS2_LOCK_TYPE_ORPHAN_SCAN] = "OrphanScan",
 };
 
-- 
GitLab


From e3b2415e281a97ade36d88404094a90cfea838c0 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Fri, 21 Aug 2009 09:47:45 +1000
Subject: [PATCH 1000/1153] drm/radeon/kms: implement the bo busy ioctl
 properly.

The previous patch assumes the ioctl already existed, when
it actually didn't.

It also didn't return the correct error code.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_gem.c | 2 +-
 drivers/gpu/drm/radeon/radeon_kms.c | 1 +
 include/drm/radeon_drm.h            | 2 ++
 3 files changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c
index d4ceff13bbb..14c19980292 100644
--- a/drivers/gpu/drm/radeon/radeon_gem.c
+++ b/drivers/gpu/drm/radeon/radeon_gem.c
@@ -283,7 +283,7 @@ int radeon_gem_busy_ioctl(struct drm_device *dev, void *data,
 	mutex_lock(&dev->struct_mutex);
 	drm_gem_object_unreference(gobj);
 	mutex_unlock(&dev->struct_mutex);
-	return 0;
+	return r;
 }
 
 int radeon_gem_wait_idle_ioctl(struct drm_device *dev, void *data,
diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c
index d2764bf6b2a..11ed672543b 100644
--- a/drivers/gpu/drm/radeon/radeon_kms.c
+++ b/drivers/gpu/drm/radeon/radeon_kms.c
@@ -318,5 +318,6 @@ struct drm_ioctl_desc radeon_ioctls_kms[] = {
 	DRM_IOCTL_DEF(DRM_RADEON_INFO, radeon_info_ioctl, DRM_AUTH),
 	DRM_IOCTL_DEF(DRM_RADEON_GEM_SET_TILING, radeon_gem_set_tiling_ioctl, DRM_AUTH),
 	DRM_IOCTL_DEF(DRM_RADEON_GEM_GET_TILING, radeon_gem_get_tiling_ioctl, DRM_AUTH),
+	DRM_IOCTL_DEF(DRM_RADEON_GEM_BUSY, radeon_gem_busy_ioctl, DRM_AUTH),
 };
 int radeon_max_kms_ioctl = DRM_ARRAY_SIZE(radeon_ioctls_kms);
diff --git a/include/drm/radeon_drm.h b/include/drm/radeon_drm.h
index f81c3232acc..b43925586b2 100644
--- a/include/drm/radeon_drm.h
+++ b/include/drm/radeon_drm.h
@@ -508,6 +508,7 @@ typedef struct {
 #define DRM_RADEON_INFO			0x27
 #define DRM_RADEON_GEM_SET_TILING	0x28
 #define DRM_RADEON_GEM_GET_TILING	0x29
+#define DRM_RADEON_GEM_BUSY		0x2a
 
 #define DRM_IOCTL_RADEON_CP_INIT    DRM_IOW( DRM_COMMAND_BASE + DRM_RADEON_CP_INIT, drm_radeon_init_t)
 #define DRM_IOCTL_RADEON_CP_START   DRM_IO(  DRM_COMMAND_BASE + DRM_RADEON_CP_START)
@@ -548,6 +549,7 @@ typedef struct {
 #define DRM_IOCTL_RADEON_INFO		DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_INFO, struct drm_radeon_info)
 #define DRM_IOCTL_RADEON_SET_TILING	DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_SET_TILING, struct drm_radeon_gem_set_tiling)
 #define DRM_IOCTL_RADEON_GET_TILING	DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_GET_TILING, struct drm_radeon_gem_get_tiling)
+#define DRM_IOCTL_RADEON_GEM_BUSY	DRM_IOWR(DRM_COMMAND_BASE + DRM_RADEON_GEM_BUSY, struct drm_radeon_gem_busy)
 
 typedef struct drm_radeon_init {
 	enum {
-- 
GitLab


From 08e4d534743f4e9af3602aebbc1cca9372762028 Mon Sep 17 00:00:00 2001
From: Thomas Hellstrom <thellstrom@vmware.com>
Date: Thu, 20 Aug 2009 19:02:31 +1000
Subject: [PATCH 1001/1153] drm: Fix sysfs device confusion.

The drm sysfs class suspend / resume methods could not distinguish
between different device types wich could lead to illegal type casts.

Use struct device_type and make sure the class suspend / resume callbacks
are aware of those. There is no per device-type suspend / resume. Only
new-style PM.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/drm_sysfs.c | 51 +++++++++++++++++++++----------------
 1 file changed, 29 insertions(+), 22 deletions(-)

diff --git a/drivers/gpu/drm/drm_sysfs.c b/drivers/gpu/drm/drm_sysfs.c
index 85ec31b3ff0..f7a615b80c7 100644
--- a/drivers/gpu/drm/drm_sysfs.c
+++ b/drivers/gpu/drm/drm_sysfs.c
@@ -22,44 +22,50 @@
 #define to_drm_minor(d) container_of(d, struct drm_minor, kdev)
 #define to_drm_connector(d) container_of(d, struct drm_connector, kdev)
 
+static struct device_type drm_sysfs_device_minor = {
+	.name = "drm_minor"
+};
+
 /**
- * drm_sysfs_suspend - DRM class suspend hook
+ * drm_class_suspend - DRM class suspend hook
  * @dev: Linux device to suspend
  * @state: power state to enter
  *
  * Just figures out what the actual struct drm_device associated with
  * @dev is and calls its suspend hook, if present.
  */
-static int drm_sysfs_suspend(struct device *dev, pm_message_t state)
+static int drm_class_suspend(struct device *dev, pm_message_t state)
 {
-	struct drm_minor *drm_minor = to_drm_minor(dev);
-	struct drm_device *drm_dev = drm_minor->dev;
-
-	if (drm_minor->type == DRM_MINOR_LEGACY &&
-	    !drm_core_check_feature(drm_dev, DRIVER_MODESET) &&
-	    drm_dev->driver->suspend)
-		return drm_dev->driver->suspend(drm_dev, state);
-
+	if (dev->type == &drm_sysfs_device_minor) {
+		struct drm_minor *drm_minor = to_drm_minor(dev);
+		struct drm_device *drm_dev = drm_minor->dev;
+
+		if (drm_minor->type == DRM_MINOR_LEGACY &&
+		    !drm_core_check_feature(drm_dev, DRIVER_MODESET) &&
+		    drm_dev->driver->suspend)
+			return drm_dev->driver->suspend(drm_dev, state);
+	}
 	return 0;
 }
 
 /**
- * drm_sysfs_resume - DRM class resume hook
+ * drm_class_resume - DRM class resume hook
  * @dev: Linux device to resume
  *
  * Just figures out what the actual struct drm_device associated with
  * @dev is and calls its resume hook, if present.
  */
-static int drm_sysfs_resume(struct device *dev)
+static int drm_class_resume(struct device *dev)
 {
-	struct drm_minor *drm_minor = to_drm_minor(dev);
-	struct drm_device *drm_dev = drm_minor->dev;
-
-	if (drm_minor->type == DRM_MINOR_LEGACY &&
-	    !drm_core_check_feature(drm_dev, DRIVER_MODESET) &&
-	    drm_dev->driver->resume)
-		return drm_dev->driver->resume(drm_dev);
-
+	if (dev->type == &drm_sysfs_device_minor) {
+		struct drm_minor *drm_minor = to_drm_minor(dev);
+		struct drm_device *drm_dev = drm_minor->dev;
+
+		if (drm_minor->type == DRM_MINOR_LEGACY &&
+		    !drm_core_check_feature(drm_dev, DRIVER_MODESET) &&
+		    drm_dev->driver->resume)
+			return drm_dev->driver->resume(drm_dev);
+	}
 	return 0;
 }
 
@@ -99,8 +105,8 @@ struct class *drm_sysfs_create(struct module *owner, char *name)
 		goto err_out;
 	}
 
-	class->suspend = drm_sysfs_suspend;
-	class->resume = drm_sysfs_resume;
+	class->suspend = drm_class_suspend;
+	class->resume = drm_class_resume;
 
 	err = class_create_file(class, &class_attr_version);
 	if (err)
@@ -480,6 +486,7 @@ int drm_sysfs_device_add(struct drm_minor *minor)
 	minor->kdev.class = drm_class;
 	minor->kdev.release = drm_sysfs_device_release;
 	minor->kdev.devt = minor->device;
+	minor->kdev.type = &drm_sysfs_device_minor;
 	if (minor->type == DRM_MINOR_CONTROL)
 		minor_str = "controlD%d";
         else if (minor->type == DRM_MINOR_RENDER)
-- 
GitLab


From 17782d99502851dc7e48114ee9c5a6d6741cba18 Mon Sep 17 00:00:00 2001
From: Dave Airlie <airlied@redhat.com>
Date: Fri, 21 Aug 2009 10:07:54 +1000
Subject: [PATCH 1002/1153] drm/radeon/kms: add r100/r200 OQ support.

This adds the relocation necessary for OQ support on the r100/r200
chipsets.

Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r100.c       | 10 ++++++++++
 drivers/gpu/drm/radeon/radeon_reg.h |  3 +++
 2 files changed, 13 insertions(+)

diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index 90ff8e0ac04..68e728e8be4 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -1091,6 +1091,16 @@ static int r100_packet0_check(struct radeon_cs_parser *p,
 			tmp |= tile_flags;
 			ib[idx] = tmp;
 			break;
+		case RADEON_RB3D_ZPASS_ADDR:
+			r = r100_cs_packet_next_reloc(p, &reloc);
+			if (r) {
+				DRM_ERROR("No reloc for ib[%d]=0x%04X\n",
+					  idx, reg);
+				r100_cs_dump_packet(p, pkt);
+				return r;
+			}
+			ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+			break;
 		default:
 			/* FIXME: we don't want to allow anyothers packet */
 			break;
diff --git a/drivers/gpu/drm/radeon/radeon_reg.h b/drivers/gpu/drm/radeon/radeon_reg.h
index 5a098f304ed..5834497b366 100644
--- a/drivers/gpu/drm/radeon/radeon_reg.h
+++ b/drivers/gpu/drm/radeon/radeon_reg.h
@@ -2337,6 +2337,9 @@
 #       define RADEON_RE_WIDTH_SHIFT        0
 #       define RADEON_RE_HEIGHT_SHIFT       16
 
+#define RADEON_RB3D_ZPASS_DATA 0x3290
+#define RADEON_RB3D_ZPASS_ADDR 0x3294
+
 #define RADEON_SE_CNTL                      0x1c4c
 #       define RADEON_FFACE_CULL_CW          (0 <<  0)
 #       define RADEON_FFACE_CULL_CCW         (1 <<  0)
-- 
GitLab


From c795b33ba171e41563ab7e25105c0cd4edd81cd7 Mon Sep 17 00:00:00 2001
From: Goldwyn Rodrigues <rgoldwyn@gmail.com>
Date: Thu, 20 Aug 2009 13:43:19 -0500
Subject: [PATCH 1003/1153] ocfs2/dlm: Wait on lockres instead of erroring
 cancel requests

In case a downconvert is queued, and a flock receives a signal,
BUG_ON(lockres->l_action != OCFS2_AST_INVALID) is triggered
because a lock cancel triggers a dlmunlock while an AST is
scheduled.

To avoid this, allow a LKM_CANCEL to pass through, and let it
wait on __dlm_wait_on_lockres().

Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
Acked-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
---
 fs/ocfs2/dlm/dlmunlock.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/fs/ocfs2/dlm/dlmunlock.c b/fs/ocfs2/dlm/dlmunlock.c
index fcf879ed693..756f5b0998e 100644
--- a/fs/ocfs2/dlm/dlmunlock.c
+++ b/fs/ocfs2/dlm/dlmunlock.c
@@ -122,7 +122,7 @@ static enum dlm_status dlmunlock_common(struct dlm_ctxt *dlm,
 	 * that still has AST's pending... */
 	in_use = !list_empty(&lock->ast_list);
 	spin_unlock(&dlm->ast_lock);
-	if (in_use) {
+	if (in_use && !(flags & LKM_CANCEL)) {
 	       mlog(ML_ERROR, "lockres %.*s: Someone is calling dlmunlock "
 		    "while waiting for an ast!", res->lockname.len,
 		    res->lockname.name);
@@ -131,7 +131,7 @@ static enum dlm_status dlmunlock_common(struct dlm_ctxt *dlm,
 
 	spin_lock(&res->spinlock);
 	if (res->state & DLM_LOCK_RES_IN_PROGRESS) {
-		if (master_node) {
+		if (master_node && !(flags & LKM_CANCEL)) {
 			mlog(ML_ERROR, "lockres in progress!\n");
 			spin_unlock(&res->spinlock);
 			return DLM_FORWARD;
-- 
GitLab


From 3b7307c2d66dd575ef24b88898b4bc4bddb254f4 Mon Sep 17 00:00:00 2001
From: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Date: Thu, 20 Aug 2009 21:41:04 -0700
Subject: [PATCH 1004/1153] Input: wacom - don't use on-stack memory for report
 buffers

Tested-by: Martin Capitanio <martin@capitanio.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
---
 drivers/input/tablet/wacom_sys.c | 43 +++++++++++++++++++++-----------
 1 file changed, 29 insertions(+), 14 deletions(-)

diff --git a/drivers/input/tablet/wacom_sys.c b/drivers/input/tablet/wacom_sys.c
index a9d5031b855..ea30c983a33 100644
--- a/drivers/input/tablet/wacom_sys.c
+++ b/drivers/input/tablet/wacom_sys.c
@@ -388,6 +388,32 @@ static int wacom_parse_hid(struct usb_interface *intf, struct hid_descriptor *hi
 	return result;
 }
 
+static int wacom_query_tablet_data(struct usb_interface *intf)
+{
+	unsigned char *rep_data;
+	int limit = 0;
+	int error;
+
+	rep_data = kmalloc(2, GFP_KERNEL);
+	if (!rep_data)
+		return -ENOMEM;
+
+	do {
+		rep_data[0] = 2;
+		rep_data[1] = 2;
+		error = usb_set_report(intf, WAC_HID_FEATURE_REPORT,
+					2, rep_data, 2);
+		if (error >= 0)
+			error = usb_get_report(intf,
+						WAC_HID_FEATURE_REPORT, 2,
+						rep_data, 2);
+	} while ((error < 0 || rep_data[1] != 2) && limit++ < 5);
+
+	kfree(rep_data);
+
+	return error < 0 ? error : 0;
+}
+
 static int wacom_probe(struct usb_interface *intf, const struct usb_device_id *id)
 {
 	struct usb_device *dev = interface_to_usbdev(intf);
@@ -398,7 +424,6 @@ static int wacom_probe(struct usb_interface *intf, const struct usb_device_id *i
 	struct wacom_features *features;
 	struct input_dev *input_dev;
 	int error = -ENOMEM;
-	char rep_data[2], limit = 0;
 	struct hid_descriptor *hid_desc;
 
 	wacom = kzalloc(sizeof(struct wacom), GFP_KERNEL);
@@ -489,20 +514,10 @@ static int wacom_probe(struct usb_interface *intf, const struct usb_device_id *i
 
 	/*
 	 * Ask the tablet to report tablet data if it is not a Tablet PC.
-	 * Repeat until it succeeds
+	 * Note that if query fails it is not a hard failure.
 	 */
-	if (wacom_wac->features->type != TABLETPC) {
-		do {
-			rep_data[0] = 2;
-			rep_data[1] = 2;
-			error = usb_set_report(intf, WAC_HID_FEATURE_REPORT,
-						2, rep_data, 2);
-			if (error >= 0)
-				error = usb_get_report(intf,
-						WAC_HID_FEATURE_REPORT, 2,
-						rep_data, 2);
-		} while ((error < 0 || rep_data[1] != 2) && limit++ < 5);
-	}
+	if (wacom_wac->features->type != TABLETPC)
+		wacom_query_tablet_data(intf);
 
 	usb_set_intfdata(intf, wacom);
 	return 0;
-- 
GitLab


From 1700f5fde88f9a251037bc86bde538ee32c59905 Mon Sep 17 00:00:00 2001
From: Marek Vasut <marek.vasut@gmail.com>
Date: Thu, 20 Aug 2009 22:05:53 -0700
Subject: [PATCH 1005/1153] Input: ucb1400_ts - enable ADC Filter

This patch enables ADC filtering on UCB1400 codec by default. The
benefit from this change is mostly on some Colibri boards where
the ADCSYNC pin of the UCB1400 codec isn't connected causing the
touchscreen to jitter very badly. This change has no visible
effect on boards where the ADCSYNC pin is connected.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Palo Revak <palo@bielyvlk.sk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
---
 drivers/input/touchscreen/ucb1400_ts.c | 9 +++++++++
 include/linux/ucb1400.h                | 4 ++++
 2 files changed, 13 insertions(+)

diff --git a/drivers/input/touchscreen/ucb1400_ts.c b/drivers/input/touchscreen/ucb1400_ts.c
index 6954f550010..3b345f9cf0c 100644
--- a/drivers/input/touchscreen/ucb1400_ts.c
+++ b/drivers/input/touchscreen/ucb1400_ts.c
@@ -345,6 +345,7 @@ static int ucb1400_ts_detect_irq(struct ucb1400_ts *ucb)
 static int ucb1400_ts_probe(struct platform_device *dev)
 {
 	int error, x_res, y_res;
+	u16 fcsr;
 	struct ucb1400_ts *ucb = dev->dev.platform_data;
 
 	ucb->ts_idev = input_allocate_device();
@@ -382,6 +383,14 @@ static int ucb1400_ts_probe(struct platform_device *dev)
 	ucb->ts_idev->evbit[0]		= BIT_MASK(EV_ABS) | BIT_MASK(EV_KEY);
 	ucb->ts_idev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
 
+	/*
+	 * Enable ADC filter to prevent horrible jitter on Colibri.
+	 * This also further reduces jitter on boards where ADCSYNC
+	 * pin is connected.
+	 */
+	fcsr = ucb1400_reg_read(ucb->ac97, UCB_FCSR);
+	ucb1400_reg_write(ucb->ac97, UCB_FCSR, fcsr | UCB_FCSR_AVE);
+
 	ucb1400_adc_enable(ucb->ac97);
 	x_res = ucb1400_ts_read_xres(ucb);
 	y_res = ucb1400_ts_read_yres(ucb);
diff --git a/include/linux/ucb1400.h b/include/linux/ucb1400.h
index ed889f4168f..ae779bb8cc0 100644
--- a/include/linux/ucb1400.h
+++ b/include/linux/ucb1400.h
@@ -73,6 +73,10 @@
 
 #define UCB_ADC_DATA		0x68
 #define UCB_ADC_DAT_VALID	(1 << 15)
+
+#define UCB_FCSR		0x6c
+#define UCB_FCSR_AVE		(1 << 12)
+
 #define UCB_ADC_DAT_MASK	0x3ff
 
 #define UCB_ID			0x7e
-- 
GitLab


From 9b2fb2da4edfb163842800abbeb4c14bc1759469 Mon Sep 17 00:00:00 2001
From: Pavel Revak <palo@bielyvlk.sk>
Date: Thu, 20 Aug 2009 22:30:54 -0700
Subject: [PATCH 1006/1153] Input: ucb1400_ts - enable interrupt
 unconditionally

Sometimes, when using the touchscreen, it stops working till next restart
and the following message is printed:

	ucb1400: unexpected IE_STATUS = 0x0

The following patch retriggers the touchscreen interrupt unconditionally.
This prevents hanging of the touchscreen in case of bogus interrupt
occurence.

Signed-off-by: Pavel Revak <palo@bielyvlk.sk>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
---
 drivers/input/touchscreen/ucb1400_ts.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/input/touchscreen/ucb1400_ts.c b/drivers/input/touchscreen/ucb1400_ts.c
index 3b345f9cf0c..3a7a58222f8 100644
--- a/drivers/input/touchscreen/ucb1400_ts.c
+++ b/drivers/input/touchscreen/ucb1400_ts.c
@@ -170,11 +170,11 @@ static void ucb1400_handle_pending_irq(struct ucb1400_ts *ucb)
 	ucb1400_reg_write(ucb->ac97, UCB_IE_CLEAR, isr);
 	ucb1400_reg_write(ucb->ac97, UCB_IE_CLEAR, 0);
 
-	if (isr & UCB_IE_TSPX) {
+	if (isr & UCB_IE_TSPX)
 		ucb1400_ts_irq_disable(ucb->ac97);
-		enable_irq(ucb->irq);
-	} else
-		printk(KERN_ERR "ucb1400: unexpected IE_STATUS = %#x\n", isr);
+	else
+		dev_dbg(&ucb->ts_idev->dev, "ucb1400: unexpected IE_STATUS = %#x\n", isr);
+	enable_irq(ucb->irq);
 }
 
 static int ucb1400_ts_thread(void *_ucb)
-- 
GitLab


From ec9c96ef3cc0124cb94375b17faaa8cff5dfdf97 Mon Sep 17 00:00:00 2001
From: Kyle McMartin <kyle@redhat.com>
Date: Wed, 19 Aug 2009 21:17:08 -0400
Subject: [PATCH 1007/1153] dma-debug: Fix check_unmap null pointer dereference

While it's debatable whether or not a NULL device argument to
the DMA API functions is valid... since it certainly isn't
valid on devices with an IOMMU... dma-debug really shouldn't be
dereferencing null pointers either.

Guard against that in err_printk and the driver_filter
functions. A Fedora rawhide user was seeing this in one of the
dvb drivers resulting in an oops on boot.

[ A patch has been sent for testing to the driver, but I feel
  the dma debugging support should be fixed as well. (There's
  still a pile of legacy garbage in the kernel passing null
  pointers to dma_{alloc,free}_*. :( ]

Signed-off-by: Kyle McMartin <kyle@redhat.com>
Cc: mchehab@infradead.org
Cc: Joerg Roedel <joerg.roedel@amd.com>
LKML-Reference: <20090820011708.GP25206@bombadil.infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 lib/dma-debug.c | 28 ++++++++++++++++------------
 1 file changed, 16 insertions(+), 12 deletions(-)

diff --git a/lib/dma-debug.c b/lib/dma-debug.c
index 65b0d99b6d0..58a9f9fc609 100644
--- a/lib/dma-debug.c
+++ b/lib/dma-debug.c
@@ -156,9 +156,13 @@ static bool driver_filter(struct device *dev)
 		return true;
 
 	/* driver filter on and initialized */
-	if (current_driver && dev->driver == current_driver)
+	if (current_driver && dev && dev->driver == current_driver)
 		return true;
 
+	/* driver filter on, but we can't filter on a NULL device... */
+	if (!dev)
+		return false;
+
 	if (current_driver || !current_driver_name[0])
 		return false;
 
@@ -183,17 +187,17 @@ static bool driver_filter(struct device *dev)
 	return ret;
 }
 
-#define err_printk(dev, entry, format, arg...) do {		\
-		error_count += 1;				\
-		if (driver_filter(dev) &&			\
-		    (show_all_errors || show_num_errors > 0)) {	\
-			WARN(1, "%s %s: " format,		\
-			     dev_driver_string(dev),		\
-			     dev_name(dev) , ## arg);		\
-			dump_entry_trace(entry);		\
-		}						\
-		if (!show_all_errors && show_num_errors > 0)	\
-			show_num_errors -= 1;			\
+#define err_printk(dev, entry, format, arg...) do {			\
+		error_count += 1;					\
+		if (driver_filter(dev) &&				\
+		    (show_all_errors || show_num_errors > 0)) {		\
+			WARN(1, "%s %s: " format,			\
+			     dev ? dev_driver_string(dev) : "NULL",	\
+			     dev ? dev_name(dev) : "NULL", ## arg);	\
+			dump_entry_trace(entry);			\
+		}							\
+		if (!show_all_errors && show_num_errors > 0)		\
+			show_num_errors -= 1;				\
 	} while (0);
 
 /*
-- 
GitLab


From 03e860bd9f6a3cca747b0795bed26279a8b420a0 Mon Sep 17 00:00:00 2001
From: "From: Nick Piggin" <npiggin@suse.de>
Date: Fri, 21 Aug 2009 10:09:44 +0200
Subject: [PATCH 1008/1153] btrfs: fix inode rbtree corruption

Node may not be inserted over existing node. This causes inode tree
corruption and I was seeing crashes in inode_tree_del which I can not
reproduce after this patch.

The other way to fix this would be to tie inode lifetime in the rbtree
with inode while not in freeing state. I had a look at this but it is
not so trivial at this point. At least this patch gets things working again.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Chris Mason <chris.mason@oracle.com>
Acked-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
---
 fs/btrfs/inode.c | 21 ++++++++++++++-------
 1 file changed, 14 insertions(+), 7 deletions(-)

diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c
index 272b9b2bea8..59cba180fe8 100644
--- a/fs/btrfs/inode.c
+++ b/fs/btrfs/inode.c
@@ -3099,8 +3099,12 @@ static void inode_tree_add(struct inode *inode)
 {
 	struct btrfs_root *root = BTRFS_I(inode)->root;
 	struct btrfs_inode *entry;
-	struct rb_node **p = &root->inode_tree.rb_node;
-	struct rb_node *parent = NULL;
+	struct rb_node **p;
+	struct rb_node *parent;
+
+again:
+	p = &root->inode_tree.rb_node;
+	parent = NULL;
 
 	spin_lock(&root->inode_lock);
 	while (*p) {
@@ -3108,13 +3112,16 @@ static void inode_tree_add(struct inode *inode)
 		entry = rb_entry(parent, struct btrfs_inode, rb_node);
 
 		if (inode->i_ino < entry->vfs_inode.i_ino)
-			p = &(*p)->rb_left;
+			p = &parent->rb_left;
 		else if (inode->i_ino > entry->vfs_inode.i_ino)
-			p = &(*p)->rb_right;
+			p = &parent->rb_right;
 		else {
 			WARN_ON(!(entry->vfs_inode.i_state &
 				  (I_WILL_FREE | I_FREEING | I_CLEAR)));
-			break;
+			rb_erase(parent, &root->inode_tree);
+			RB_CLEAR_NODE(parent);
+			spin_unlock(&root->inode_lock);
+			goto again;
 		}
 	}
 	rb_link_node(&BTRFS_I(inode)->rb_node, parent, p);
@@ -3126,12 +3133,12 @@ static void inode_tree_del(struct inode *inode)
 {
 	struct btrfs_root *root = BTRFS_I(inode)->root;
 
+	spin_lock(&root->inode_lock);
 	if (!RB_EMPTY_NODE(&BTRFS_I(inode)->rb_node)) {
-		spin_lock(&root->inode_lock);
 		rb_erase(&BTRFS_I(inode)->rb_node, &root->inode_tree);
-		spin_unlock(&root->inode_lock);
 		RB_CLEAR_NODE(&BTRFS_I(inode)->rb_node);
 	}
+	spin_unlock(&root->inode_lock);
 }
 
 static noinline void init_btrfs_i(struct inode *inode)
-- 
GitLab


From f779b3e513478218cbaaaa0a506d7801cab6fd14 Mon Sep 17 00:00:00 2001
From: Alex Deucher <alexdeucher@gmail.com>
Date: Wed, 19 Aug 2009 19:11:39 -0400
Subject: [PATCH 1009/1153] drm/radeon: add GET_PARAM/INFO support for Z pipes

Needed for occlusion queries on rv530 chips.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/r300.c         |  4 +++-
 drivers/gpu/drm/radeon/r420.c         | 13 ++++++++++++-
 drivers/gpu/drm/radeon/r520.c         |  1 -
 drivers/gpu/drm/radeon/radeon.h       |  1 +
 drivers/gpu/drm/radeon/radeon_cp.c    |  9 +++++++++
 drivers/gpu/drm/radeon/radeon_drv.h   |  5 ++++-
 drivers/gpu/drm/radeon/radeon_kms.c   |  3 +++
 drivers/gpu/drm/radeon/radeon_reg.h   |  2 ++
 drivers/gpu/drm/radeon/radeon_state.c |  3 +++
 include/drm/radeon_drm.h              |  2 ++
 10 files changed, 39 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/radeon/r300.c b/drivers/gpu/drm/radeon/r300.c
index c47579dcafa..053f4ec397f 100644
--- a/drivers/gpu/drm/radeon/r300.c
+++ b/drivers/gpu/drm/radeon/r300.c
@@ -448,6 +448,7 @@ void r300_gpu_init(struct radeon_device *rdev)
 		/* rv350,rv370,rv380 */
 		rdev->num_gb_pipes = 1;
 	}
+	rdev->num_z_pipes = 1;
 	gb_tile_config = (R300_ENABLE_TILING | R300_TILE_SIZE_16);
 	switch (rdev->num_gb_pipes) {
 	case 2:
@@ -486,7 +487,8 @@ void r300_gpu_init(struct radeon_device *rdev)
 		printk(KERN_WARNING "Failed to wait MC idle while "
 		       "programming pipes. Bad things might happen.\n");
 	}
-	DRM_INFO("radeon: %d pipes initialized.\n", rdev->num_gb_pipes);
+	DRM_INFO("radeon: %d quad pipes, %d Z pipes initialized.\n",
+		 rdev->num_gb_pipes, rdev->num_z_pipes);
 }
 
 int r300_ga_reset(struct radeon_device *rdev)
diff --git a/drivers/gpu/drm/radeon/r420.c b/drivers/gpu/drm/radeon/r420.c
index dea497a979f..97426a6f370 100644
--- a/drivers/gpu/drm/radeon/r420.c
+++ b/drivers/gpu/drm/radeon/r420.c
@@ -165,7 +165,18 @@ void r420_pipes_init(struct radeon_device *rdev)
 		printk(KERN_WARNING "Failed to wait GUI idle while "
 		       "programming pipes. Bad things might happen.\n");
 	}
-	DRM_INFO("radeon: %d pipes initialized.\n", rdev->num_gb_pipes);
+
+	if (rdev->family == CHIP_RV530) {
+		tmp = RREG32(RV530_GB_PIPE_SELECT2);
+		if ((tmp & 3) == 3)
+			rdev->num_z_pipes = 2;
+		else
+			rdev->num_z_pipes = 1;
+	} else
+		rdev->num_z_pipes = 1;
+
+	DRM_INFO("radeon: %d quad pipes, %d z pipes initialized.\n",
+		 rdev->num_gb_pipes, rdev->num_z_pipes);
 }
 
 void r420_gpu_init(struct radeon_device *rdev)
diff --git a/drivers/gpu/drm/radeon/r520.c b/drivers/gpu/drm/radeon/r520.c
index 09fb0b6ec7d..ebd6b0f7bdf 100644
--- a/drivers/gpu/drm/radeon/r520.c
+++ b/drivers/gpu/drm/radeon/r520.c
@@ -177,7 +177,6 @@ void r520_gpu_init(struct radeon_device *rdev)
 	 */
 	/* workaround for RV530 */
 	if (rdev->family == CHIP_RV530) {
-		WREG32(0x4124, 1);
 		WREG32(0x4128, 0xFF);
 	}
 	r420_pipes_init(rdev);
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index 79ad98264e3..b519fb2fecb 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -655,6 +655,7 @@ struct radeon_device {
 	int				usec_timeout;
 	enum radeon_pll_errata		pll_errata;
 	int				num_gb_pipes;
+	int				num_z_pipes;
 	int				disp_priority;
 	/* BIOS */
 	uint8_t				*bios;
diff --git a/drivers/gpu/drm/radeon/radeon_cp.c b/drivers/gpu/drm/radeon/radeon_cp.c
index d8356827ef1..7a52c461145 100644
--- a/drivers/gpu/drm/radeon/radeon_cp.c
+++ b/drivers/gpu/drm/radeon/radeon_cp.c
@@ -406,6 +406,15 @@ static void radeon_init_pipes(drm_radeon_private_t *dev_priv)
 {
 	uint32_t gb_tile_config, gb_pipe_sel = 0;
 
+	if ((dev_priv->flags & RADEON_FAMILY_MASK) == CHIP_RV530) {
+		uint32_t z_pipe_sel = RADEON_READ(RV530_GB_PIPE_SELECT2);
+		if ((z_pipe_sel & 3) == 3)
+			dev_priv->num_z_pipes = 2;
+		else
+			dev_priv->num_z_pipes = 1;
+	} else
+		dev_priv->num_z_pipes = 1;
+
 	/* RS4xx/RS6xx/R4xx/R5xx */
 	if ((dev_priv->flags & RADEON_FAMILY_MASK) >= CHIP_R420) {
 		gb_pipe_sel = RADEON_READ(R400_GB_PIPE_SELECT);
diff --git a/drivers/gpu/drm/radeon/radeon_drv.h b/drivers/gpu/drm/radeon/radeon_drv.h
index 3933f8216a3..6fa32dac4e9 100644
--- a/drivers/gpu/drm/radeon/radeon_drv.h
+++ b/drivers/gpu/drm/radeon/radeon_drv.h
@@ -100,9 +100,10 @@
  * 1.28- Add support for VBL on CRTC2
  * 1.29- R500 3D cmd buffer support
  * 1.30- Add support for occlusion queries
+ * 1.31- Add support for num Z pipes from GET_PARAM
  */
 #define DRIVER_MAJOR		1
-#define DRIVER_MINOR		30
+#define DRIVER_MINOR		31
 #define DRIVER_PATCHLEVEL	0
 
 /*
@@ -329,6 +330,7 @@ typedef struct drm_radeon_private {
 	resource_size_t fb_aper_offset;
 
 	int num_gb_pipes;
+	int num_z_pipes;
 	int track_flush;
 	drm_local_map_t *mmio;
 
@@ -689,6 +691,7 @@ extern void r600_page_table_cleanup(struct drm_device *dev, struct drm_ati_pciga
 
 /* pipe config regs */
 #define R400_GB_PIPE_SELECT             0x402c
+#define RV530_GB_PIPE_SELECT2           0x4124
 #define R500_DYN_SCLK_PWMEM_PIPE        0x000d /* PLL */
 #define R300_GB_TILE_CONFIG             0x4018
 #       define R300_ENABLE_TILING       (1 << 0)
diff --git a/drivers/gpu/drm/radeon/radeon_kms.c b/drivers/gpu/drm/radeon/radeon_kms.c
index 11ed672543b..dce09ada32b 100644
--- a/drivers/gpu/drm/radeon/radeon_kms.c
+++ b/drivers/gpu/drm/radeon/radeon_kms.c
@@ -95,6 +95,9 @@ int radeon_info_ioctl(struct drm_device *dev, void *data, struct drm_file *filp)
 	case RADEON_INFO_NUM_GB_PIPES:
 		value = rdev->num_gb_pipes;
 		break;
+	case RADEON_INFO_NUM_Z_PIPES:
+		value = rdev->num_z_pipes;
+		break;
 	default:
 		DRM_DEBUG("Invalid request %d\n", info->request);
 		return -EINVAL;
diff --git a/drivers/gpu/drm/radeon/radeon_reg.h b/drivers/gpu/drm/radeon/radeon_reg.h
index 5834497b366..4df43f62c67 100644
--- a/drivers/gpu/drm/radeon/radeon_reg.h
+++ b/drivers/gpu/drm/radeon/radeon_reg.h
@@ -3574,4 +3574,6 @@
 #define RADEON_SCRATCH_REG4		0x15f0
 #define RADEON_SCRATCH_REG5		0x15f4
 
+#define RV530_GB_PIPE_SELECT2           0x4124
+
 #endif
diff --git a/drivers/gpu/drm/radeon/radeon_state.c b/drivers/gpu/drm/radeon/radeon_state.c
index 46645f3e032..2882f40d5ec 100644
--- a/drivers/gpu/drm/radeon/radeon_state.c
+++ b/drivers/gpu/drm/radeon/radeon_state.c
@@ -3081,6 +3081,9 @@ static int radeon_cp_getparam(struct drm_device *dev, void *data, struct drm_fil
 	case RADEON_PARAM_NUM_GB_PIPES:
 		value = dev_priv->num_gb_pipes;
 		break;
+	case RADEON_PARAM_NUM_Z_PIPES:
+		value = dev_priv->num_z_pipes;
+		break;
 	default:
 		DRM_DEBUG("Invalid parameter %d\n", param->param);
 		return -EINVAL;
diff --git a/include/drm/radeon_drm.h b/include/drm/radeon_drm.h
index b43925586b2..2ba61e18fc8 100644
--- a/include/drm/radeon_drm.h
+++ b/include/drm/radeon_drm.h
@@ -709,6 +709,7 @@ typedef struct drm_radeon_indirect {
 #define RADEON_PARAM_FB_LOCATION           14   /* FB location */
 #define RADEON_PARAM_NUM_GB_PIPES          15   /* num GB pipes */
 #define RADEON_PARAM_DEVICE_ID             16
+#define RADEON_PARAM_NUM_Z_PIPES           17   /* num Z pipes */
 
 typedef struct drm_radeon_getparam {
 	int param;
@@ -897,6 +898,7 @@ struct drm_radeon_cs {
 
 #define RADEON_INFO_DEVICE_ID		0x00
 #define RADEON_INFO_NUM_GB_PIPES	0x01
+#define RADEON_INFO_NUM_Z_PIPES 	0x02
 
 struct drm_radeon_info {
 	uint32_t		request;
-- 
GitLab


From 4a683bf94b8a10e2bb0da07aec3ac0a55e5de61f Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Fri, 21 Aug 2009 12:53:36 +0200
Subject: [PATCH 1010/1153] tracing: Fix too large stack usage in
 do_one_initcall()

One of my testboxes triggered this nasty stack overflow crash
during SCSI probing:

[    5.874004] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.875004] device: 'sda': device_add
[    5.878004] BUG: unable to handle kernel NULL pointer dereference at 00000a0c
[    5.878004] IP: [<b1008321>] print_context_stack+0x81/0x110
[    5.878004] *pde = 00000000
[    5.878004] Thread overran stack, or stack corrupted
[    5.878004] Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
[    5.878004] last sysfs file:
[    5.878004]
[    5.878004] Pid: 1, comm: swapper Not tainted (2.6.31-rc6-tip-01272-g9919e28-dirty #5685)
[    5.878004] EIP: 0060:[<b1008321>] EFLAGS: 00010083 CPU: 0
[    5.878004] EIP is at print_context_stack+0x81/0x110
[    5.878004] EAX: cf8a3000 EBX: cf8a3fe4 ECX: 00000049 EDX: 00000000
[    5.878004] ESI: b1cfce84 EDI: 00000000 EBP: cf8a3018 ESP: cf8a2ff4
[    5.878004]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[    5.878004] Process swapper (pid: 1, ti=cf8a2000 task=cf8a8000 task.ti=cf8a3000)
[    5.878004] Stack:
[    5.878004]  b1004867 fffff000 cf8a3ffc
[    5.878004] Call Trace:
[    5.878004]  [<b1004867>] ? kernel_thread_helper+0x7/0x10
[    5.878004] BUG: unable to handle kernel NULL pointer dereference at 00000a0c
[    5.878004] IP: [<b1008321>] print_context_stack+0x81/0x110
[    5.878004] *pde = 00000000
[    5.878004] Thread overran stack, or stack corrupted
[    5.878004] Oops: 0000 [#2] PREEMPT SMP DEBUG_PAGEALLOC

The oops did not reveal any more details about the real stack
that we have and the system got into an infinite loop of
recursive pagefaults.

So i booted with CONFIG_STACK_TRACER=y and the 'stacktrace' boot
parameter. The box did not crash (timings/conditions probably
changed a tiny bit to trigger the catastrophic crash), but the
/debug/tracing/stack_trace file was rather revealing:

        Depth    Size   Location    (72 entries)
        -----    ----   --------
  0)     3704      52   __change_page_attr+0xb8/0x290
  1)     3652      24   __change_page_attr_set_clr+0x43/0x90
  2)     3628      60   kernel_map_pages+0x108/0x120
  3)     3568      40   prep_new_page+0x7d/0x130
  4)     3528      84   get_page_from_freelist+0x106/0x420
  5)     3444     116   __alloc_pages_nodemask+0xd7/0x550
  6)     3328      36   allocate_slab+0xb1/0x100
  7)     3292      36   new_slab+0x1c/0x160
  8)     3256      36   __slab_alloc+0x133/0x2b0
  9)     3220       4   kmem_cache_alloc+0x1bb/0x1d0
 10)     3216     108   create_object+0x28/0x250
 11)     3108      40   kmemleak_alloc+0x81/0xc0
 12)     3068      24   kmem_cache_alloc+0x162/0x1d0
 13)     3044      52   scsi_pool_alloc_command+0x29/0x70
 14)     2992      20   scsi_host_alloc_command+0x22/0x70
 15)     2972      24   __scsi_get_command+0x1b/0x90
 16)     2948      28   scsi_get_command+0x35/0x90
 17)     2920      24   scsi_setup_blk_pc_cmnd+0xd4/0x100
 18)     2896     128   sd_prep_fn+0x332/0xa70
 19)     2768      36   blk_peek_request+0xe7/0x1d0
 20)     2732      56   scsi_request_fn+0x54/0x520
 21)     2676      12   __generic_unplug_device+0x2b/0x40
 22)     2664      24   blk_execute_rq_nowait+0x59/0x80
 23)     2640     172   blk_execute_rq+0x6b/0xb0
 24)     2468      32   scsi_execute+0xe0/0x140
 25)     2436      64   scsi_execute_req+0x152/0x160
 26)     2372      60   scsi_vpd_inquiry+0x6c/0x90
 27)     2312      44   scsi_get_vpd_page+0x112/0x160
 28)     2268      52   sd_revalidate_disk+0x1df/0x320
 29)     2216      92   rescan_partitions+0x98/0x330
 30)     2124      52   __blkdev_get+0x309/0x350
 31)     2072       8   blkdev_get+0xf/0x20
 32)     2064      44   register_disk+0xff/0x120
 33)     2020      36   add_disk+0x6e/0xb0
 34)     1984      44   sd_probe_async+0xfb/0x1d0
 35)     1940      44   __async_schedule+0xf4/0x1b0
 36)     1896       8   async_schedule+0x12/0x20
 37)     1888      60   sd_probe+0x305/0x360
 38)     1828      44   really_probe+0x63/0x170
 39)     1784      36   driver_probe_device+0x5d/0x60
 40)     1748      16   __device_attach+0x49/0x50
 41)     1732      32   bus_for_each_drv+0x5b/0x80
 42)     1700      24   device_attach+0x6b/0x70
 43)     1676      16   bus_attach_device+0x47/0x60
 44)     1660      76   device_add+0x33d/0x400
 45)     1584      52   scsi_sysfs_add_sdev+0x6a/0x2c0
 46)     1532     108   scsi_add_lun+0x44b/0x460
 47)     1424     116   scsi_probe_and_add_lun+0x182/0x4e0
 48)     1308      36   __scsi_add_device+0xd9/0xe0
 49)     1272      44   ata_scsi_scan_host+0x10b/0x190
 50)     1228      24   async_port_probe+0x96/0xd0
 51)     1204      44   __async_schedule+0xf4/0x1b0
 52)     1160       8   async_schedule+0x12/0x20
 53)     1152      48   ata_host_register+0x171/0x1d0
 54)     1104      60   ata_pci_sff_activate_host+0xf3/0x230
 55)     1044      44   ata_pci_sff_init_one+0xea/0x100
 56)     1000      48   amd_init_one+0xb2/0x190
 57)      952       8   local_pci_probe+0x13/0x20
 58)      944      32   pci_device_probe+0x68/0x90
 59)      912      44   really_probe+0x63/0x170
 60)      868      36   driver_probe_device+0x5d/0x60
 61)      832      20   __driver_attach+0x89/0xa0
 62)      812      32   bus_for_each_dev+0x5b/0x80
 63)      780      12   driver_attach+0x1e/0x20
 64)      768      72   bus_add_driver+0x14b/0x2d0
 65)      696      36   driver_register+0x6e/0x150
 66)      660      20   __pci_register_driver+0x53/0xc0
 67)      640       8   amd_init+0x14/0x16
 68)      632     572   do_one_initcall+0x2b/0x1d0
 69)       60      12   do_basic_setup+0x56/0x6a
 70)       48      20   kernel_init+0x84/0xce
 71)       28      28   kernel_thread_helper+0x7/0x10

There's a lot of fat functions on that stack trace, but
the largest of all is do_one_initcall(). This is due to
the boot trace entry variables being on the stack.

Fixing this is relatively easy, initcalls are fundamentally
serialized, so we can move the local variables to file scope.

Note that this large stack footprint was present for a
couple of months already - what pushed my system over
the edge was the addition of kmemleak to the call-chain:

  6)     3328      36   allocate_slab+0xb1/0x100
  7)     3292      36   new_slab+0x1c/0x160
  8)     3256      36   __slab_alloc+0x133/0x2b0
  9)     3220       4   kmem_cache_alloc+0x1bb/0x1d0
 10)     3216     108   create_object+0x28/0x250
 11)     3108      40   kmemleak_alloc+0x81/0xc0
 12)     3068      24   kmem_cache_alloc+0x162/0x1d0
 13)     3044      52   scsi_pool_alloc_command+0x29/0x70

This pushes the total to ~3800 bytes, only a tiny bit
more was needed to corrupt the on-kernel-stack thread_info.

The fix reduces the stack footprint from 572 bytes
to 28 bytes.

Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 init/main.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/init/main.c b/init/main.c
index 2c5ade79eb8..98e679e3494 100644
--- a/init/main.c
+++ b/init/main.c
@@ -733,13 +733,14 @@ static void __init do_ctors(void)
 int initcall_debug;
 core_param(initcall_debug, initcall_debug, bool, 0644);
 
+static char msgbuf[64];
+static struct boot_trace_call call;
+static struct boot_trace_ret ret;
+
 int do_one_initcall(initcall_t fn)
 {
 	int count = preempt_count();
 	ktime_t calltime, delta, rettime;
-	char msgbuf[64];
-	struct boot_trace_call call;
-	struct boot_trace_ret ret;
 
 	if (initcall_debug) {
 		call.caller = task_pid_nr(current);
-- 
GitLab


From 4464fcaa9cbfc9c551956b48af203e2f775ca892 Mon Sep 17 00:00:00 2001
From: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Fri, 21 Aug 2009 17:19:36 +0200
Subject: [PATCH 1011/1153] perf_counter: Fix typo in read() output generation

When you iterate a list, using the iterator is useful.

Before:

   ID: 5
   ID: 5
   ID: 5
   ID: 5
   EVNT: 0x40088b scale: nan ID: 5 CNT: 1006252 ID: 6 CNT: 1011090 ID: 7 CNT: 1011196 ID: 8 CNT: 1011095
   EVNT: 0x40088c scale: 1.000000 ID: 5 CNT: 2003065 ID: 6 CNT: 2011671 ID: 7 CNT: 2012620 ID: 8 CNT: 2013479
   EVNT: 0x40088c scale: 1.000000 ID: 5 CNT: 3002390 ID: 6 CNT: 3015996 ID: 7 CNT: 3018019 ID: 8 CNT: 3020006
   EVNT: 0x40088b scale: 1.000000 ID: 5 CNT: 4002406 ID: 6 CNT: 4021120 ID: 7 CNT: 4024241 ID: 8 CNT: 4027059

After:

   ID: 1
   ID: 2
   ID: 3
   ID: 4
   EVNT: 0x400889 scale: nan ID: 1 CNT: 1005270 ID: 2 CNT: 1009833 ID: 3 CNT: 1010065 ID: 4 CNT: 1010088
   EVNT: 0x400898 scale: nan ID: 1 CNT: 2001531 ID: 2 CNT: 2022309 ID: 3 CNT: 2022470 ID: 4 CNT: 2022627
   EVNT: 0x400888 scale: 0.489467 ID: 1 CNT: 3001261 ID: 2 CNT: 3027088 ID: 3 CNT: 3027941 ID: 4 CNT: 3028762

Reported-by: stephane eranian <eranian@googlemail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey J Ashford <cjashfor@us.ibm.com>
Cc: perfmon2-devel <perfmon2-devel@lists.sourceforge.net>
LKML-Reference: <1250867976.7538.73.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 kernel/perf_counter.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/kernel/perf_counter.c b/kernel/perf_counter.c
index 36f65e2b8b5..f274e195988 100644
--- a/kernel/perf_counter.c
+++ b/kernel/perf_counter.c
@@ -1791,7 +1791,7 @@ static int perf_counter_read_group(struct perf_counter *counter,
 	size += err;
 
 	list_for_each_entry(sub, &leader->sibling_list, list_entry) {
-		err = perf_counter_read_entry(counter, read_format,
+		err = perf_counter_read_entry(sub, read_format,
 				buf + size);
 		if (err < 0)
 			return err;
-- 
GitLab


From 83d349f35e1ae72268c5104dbf9ab2ae635425d4 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Fri, 21 Aug 2009 09:23:57 -0700
Subject: [PATCH 1012/1153] x86: don't send an IPI to the empty set of CPU's
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy.  So
just warn if a caller gives us an empty mask, and ignore it.

This fixes a regression in 2.6.30.x, due to commit 4595f9620 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:

	http://bugzilla.kernel.org/show_bug.cgi?id=13933

which causes a silent lock-up.  It only seems to happen on PPro, P2, P3
and Athlon XP cores.  Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's.  Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.

Reported-by: Pavel Vilim <wylda@volny.cz>
Reported-and-tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Reported-and-tested-by: Martin Rogge <marogge@onlinehome.de>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 arch/x86/kernel/apic/ipi.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/x86/kernel/apic/ipi.c b/arch/x86/kernel/apic/ipi.c
index dbf5445727a..6ef00ba4c88 100644
--- a/arch/x86/kernel/apic/ipi.c
+++ b/arch/x86/kernel/apic/ipi.c
@@ -106,6 +106,9 @@ void default_send_IPI_mask_logical(const struct cpumask *cpumask, int vector)
 	unsigned long mask = cpumask_bits(cpumask)[0];
 	unsigned long flags;
 
+	if (WARN_ONCE(!mask, "empty IPI mask"))
+		return;
+
 	local_irq_save(flags);
 	WARN_ON(mask & ~cpumask_bits(cpu_online_mask)[0]);
 	__default_send_IPI_dest_field(mask, vector, apic->dest_logical);
-- 
GitLab


From f4b0373b26567cafd421d91101852ed7a34e9e94 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Fri, 21 Aug 2009 09:26:15 -0700
Subject: [PATCH 1013/1153] Make bitmask 'and' operators return a result code

When 'and'ing two bitmasks (where 'andnot' is a variation on it), some
cases want to know whether the result is the empty set or not.  In
particular, the TLB IPI sending code wants to do cpumask operations and
determine if there are any CPU's left in the final set.

So this just makes the bitmask (and cpumask) functions return a boolean
for whether the result has any bits set.

Cc: stable@kernel.org (2.6.30, needed by TLB shootdown fix)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/bitmap.h  | 18 ++++++++----------
 include/linux/cpumask.h | 20 ++++++++++----------
 lib/bitmap.c            | 12 ++++++++----
 3 files changed, 26 insertions(+), 24 deletions(-)

diff --git a/include/linux/bitmap.h b/include/linux/bitmap.h
index 2878811c613..756d78b8c1c 100644
--- a/include/linux/bitmap.h
+++ b/include/linux/bitmap.h
@@ -94,13 +94,13 @@ extern void __bitmap_shift_right(unsigned long *dst,
                         const unsigned long *src, int shift, int bits);
 extern void __bitmap_shift_left(unsigned long *dst,
                         const unsigned long *src, int shift, int bits);
-extern void __bitmap_and(unsigned long *dst, const unsigned long *bitmap1,
+extern int __bitmap_and(unsigned long *dst, const unsigned long *bitmap1,
 			const unsigned long *bitmap2, int bits);
 extern void __bitmap_or(unsigned long *dst, const unsigned long *bitmap1,
 			const unsigned long *bitmap2, int bits);
 extern void __bitmap_xor(unsigned long *dst, const unsigned long *bitmap1,
 			const unsigned long *bitmap2, int bits);
-extern void __bitmap_andnot(unsigned long *dst, const unsigned long *bitmap1,
+extern int __bitmap_andnot(unsigned long *dst, const unsigned long *bitmap1,
 			const unsigned long *bitmap2, int bits);
 extern int __bitmap_intersects(const unsigned long *bitmap1,
 			const unsigned long *bitmap2, int bits);
@@ -171,13 +171,12 @@ static inline void bitmap_copy(unsigned long *dst, const unsigned long *src,
 	}
 }
 
-static inline void bitmap_and(unsigned long *dst, const unsigned long *src1,
+static inline int bitmap_and(unsigned long *dst, const unsigned long *src1,
 			const unsigned long *src2, int nbits)
 {
 	if (small_const_nbits(nbits))
-		*dst = *src1 & *src2;
-	else
-		__bitmap_and(dst, src1, src2, nbits);
+		return (*dst = *src1 & *src2) != 0;
+	return __bitmap_and(dst, src1, src2, nbits);
 }
 
 static inline void bitmap_or(unsigned long *dst, const unsigned long *src1,
@@ -198,13 +197,12 @@ static inline void bitmap_xor(unsigned long *dst, const unsigned long *src1,
 		__bitmap_xor(dst, src1, src2, nbits);
 }
 
-static inline void bitmap_andnot(unsigned long *dst, const unsigned long *src1,
+static inline int bitmap_andnot(unsigned long *dst, const unsigned long *src1,
 			const unsigned long *src2, int nbits)
 {
 	if (small_const_nbits(nbits))
-		*dst = *src1 & ~(*src2);
-	else
-		__bitmap_andnot(dst, src1, src2, nbits);
+		return (*dst = *src1 & ~(*src2)) != 0;
+	return __bitmap_andnot(dst, src1, src2, nbits);
 }
 
 static inline void bitmap_complement(unsigned long *dst, const unsigned long *src,
diff --git a/include/linux/cpumask.h b/include/linux/cpumask.h
index c5ac87ca7bc..796df12091b 100644
--- a/include/linux/cpumask.h
+++ b/include/linux/cpumask.h
@@ -43,10 +43,10 @@
  * int cpu_isset(cpu, mask)		true iff bit 'cpu' set in mask
  * int cpu_test_and_set(cpu, mask)	test and set bit 'cpu' in mask
  *
- * void cpus_and(dst, src1, src2)	dst = src1 & src2  [intersection]
+ * int cpus_and(dst, src1, src2)	dst = src1 & src2  [intersection]
  * void cpus_or(dst, src1, src2)	dst = src1 | src2  [union]
  * void cpus_xor(dst, src1, src2)	dst = src1 ^ src2
- * void cpus_andnot(dst, src1, src2)	dst = src1 & ~src2
+ * int cpus_andnot(dst, src1, src2)	dst = src1 & ~src2
  * void cpus_complement(dst, src)	dst = ~src
  *
  * int cpus_equal(mask1, mask2)		Does mask1 == mask2?
@@ -179,10 +179,10 @@ static inline int __cpu_test_and_set(int cpu, cpumask_t *addr)
 }
 
 #define cpus_and(dst, src1, src2) __cpus_and(&(dst), &(src1), &(src2), NR_CPUS)
-static inline void __cpus_and(cpumask_t *dstp, const cpumask_t *src1p,
+static inline int __cpus_and(cpumask_t *dstp, const cpumask_t *src1p,
 					const cpumask_t *src2p, int nbits)
 {
-	bitmap_and(dstp->bits, src1p->bits, src2p->bits, nbits);
+	return bitmap_and(dstp->bits, src1p->bits, src2p->bits, nbits);
 }
 
 #define cpus_or(dst, src1, src2) __cpus_or(&(dst), &(src1), &(src2), NR_CPUS)
@@ -201,10 +201,10 @@ static inline void __cpus_xor(cpumask_t *dstp, const cpumask_t *src1p,
 
 #define cpus_andnot(dst, src1, src2) \
 				__cpus_andnot(&(dst), &(src1), &(src2), NR_CPUS)
-static inline void __cpus_andnot(cpumask_t *dstp, const cpumask_t *src1p,
+static inline int __cpus_andnot(cpumask_t *dstp, const cpumask_t *src1p,
 					const cpumask_t *src2p, int nbits)
 {
-	bitmap_andnot(dstp->bits, src1p->bits, src2p->bits, nbits);
+	return bitmap_andnot(dstp->bits, src1p->bits, src2p->bits, nbits);
 }
 
 #define cpus_complement(dst, src) __cpus_complement(&(dst), &(src), NR_CPUS)
@@ -738,11 +738,11 @@ static inline void cpumask_clear(struct cpumask *dstp)
  * @src1p: the first input
  * @src2p: the second input
  */
-static inline void cpumask_and(struct cpumask *dstp,
+static inline int cpumask_and(struct cpumask *dstp,
 			       const struct cpumask *src1p,
 			       const struct cpumask *src2p)
 {
-	bitmap_and(cpumask_bits(dstp), cpumask_bits(src1p),
+	return bitmap_and(cpumask_bits(dstp), cpumask_bits(src1p),
 				       cpumask_bits(src2p), nr_cpumask_bits);
 }
 
@@ -779,11 +779,11 @@ static inline void cpumask_xor(struct cpumask *dstp,
  * @src1p: the first input
  * @src2p: the second input
  */
-static inline void cpumask_andnot(struct cpumask *dstp,
+static inline int cpumask_andnot(struct cpumask *dstp,
 				  const struct cpumask *src1p,
 				  const struct cpumask *src2p)
 {
-	bitmap_andnot(cpumask_bits(dstp), cpumask_bits(src1p),
+	return bitmap_andnot(cpumask_bits(dstp), cpumask_bits(src1p),
 					  cpumask_bits(src2p), nr_cpumask_bits);
 }
 
diff --git a/lib/bitmap.c b/lib/bitmap.c
index 35a1f7ff414..702565821c9 100644
--- a/lib/bitmap.c
+++ b/lib/bitmap.c
@@ -179,14 +179,16 @@ void __bitmap_shift_left(unsigned long *dst,
 }
 EXPORT_SYMBOL(__bitmap_shift_left);
 
-void __bitmap_and(unsigned long *dst, const unsigned long *bitmap1,
+int __bitmap_and(unsigned long *dst, const unsigned long *bitmap1,
 				const unsigned long *bitmap2, int bits)
 {
 	int k;
 	int nr = BITS_TO_LONGS(bits);
+	unsigned long result = 0;
 
 	for (k = 0; k < nr; k++)
-		dst[k] = bitmap1[k] & bitmap2[k];
+		result |= (dst[k] = bitmap1[k] & bitmap2[k]);
+	return result != 0;
 }
 EXPORT_SYMBOL(__bitmap_and);
 
@@ -212,14 +214,16 @@ void __bitmap_xor(unsigned long *dst, const unsigned long *bitmap1,
 }
 EXPORT_SYMBOL(__bitmap_xor);
 
-void __bitmap_andnot(unsigned long *dst, const unsigned long *bitmap1,
+int __bitmap_andnot(unsigned long *dst, const unsigned long *bitmap1,
 				const unsigned long *bitmap2, int bits)
 {
 	int k;
 	int nr = BITS_TO_LONGS(bits);
+	unsigned long result = 0;
 
 	for (k = 0; k < nr; k++)
-		dst[k] = bitmap1[k] & ~bitmap2[k];
+		result |= (dst[k] = bitmap1[k] & ~bitmap2[k]);
+	return result != 0;
 }
 EXPORT_SYMBOL(__bitmap_andnot);
 
-- 
GitLab


From 1a9937b7f07ab6e35515e32a7625f0ba50ab7670 Mon Sep 17 00:00:00 2001
From: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Date: Thu, 20 Aug 2009 21:16:17 -0300
Subject: [PATCH 1014/1153] rtl8187: always set MSR_LINK_ENEDCA flag with
 RTL8187B

RTL8187B always needs MSR_LINK_ENEDCA flag to be set even when it is in
no link mode, otherwise it'll not be able to associate when this flag is
not set after the change "mac80211: fix managed mode BSSID handling".

By accident, setting BSSID of AP before association makes 8187B to
successfuly associate even when ENEDCA flag isn't set, which was the
case before the mac80211 change. But now the BSSID of AP we are trying
to associate is only available after association is successful, and
any attempt to associate without the needed flag doesn't work.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
---
 drivers/net/wireless/rtl818x/rtl8187_dev.c | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/rtl818x/rtl8187_dev.c b/drivers/net/wireless/rtl818x/rtl8187_dev.c
index 294250e294d..87a95588a8e 100644
--- a/drivers/net/wireless/rtl818x/rtl8187_dev.c
+++ b/drivers/net/wireless/rtl818x/rtl8187_dev.c
@@ -869,6 +869,9 @@ static int rtl8187b_init_hw(struct ieee80211_hw *dev)
 	priv->aifsn[3] = 3; /* AIFSN[AC_BE] */
 	rtl818x_iowrite8(priv, &priv->map->ACM_CONTROL, 0);
 
+	/* ENEDCA flag must always be set, transmit issues? */
+	rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_ENEDCA);
+
 	return 0;
 }
 
@@ -1173,13 +1176,16 @@ static void rtl8187_bss_info_changed(struct ieee80211_hw *dev,
 			rtl818x_iowrite8(priv, &priv->map->BSSID[i],
 					 info->bssid[i]);
 
+		if (priv->is_rtl8187b)
+			reg = RTL818X_MSR_ENEDCA;
+		else
+			reg = 0;
+
 		if (is_valid_ether_addr(info->bssid)) {
-			reg = RTL818X_MSR_INFRA;
-			if (priv->is_rtl8187b)
-				reg |= RTL818X_MSR_ENEDCA;
+			reg |= RTL818X_MSR_INFRA;
 			rtl818x_iowrite8(priv, &priv->map->MSR, reg);
 		} else {
-			reg = RTL818X_MSR_NO_LINK;
+			reg |= RTL818X_MSR_NO_LINK;
 			rtl818x_iowrite8(priv, &priv->map->MSR, reg);
 		}
 
-- 
GitLab


From b04e6373d694e977c95ae0ae000e2c1e2cf92d73 Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Fri, 21 Aug 2009 09:48:10 -0700
Subject: [PATCH 1015/1153] x86: don't call '->send_IPI_mask()' with an empty
 mask
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

As noted in 83d349f35e1ae72268c5104dbf9ab2ae635425d4 ("x86: don't send
an IPI to the empty set of CPU's"), some APIC's will be very unhappy
with an empty destination mask.  That commit added a WARN_ON() for that
case, and avoided the resulting problem, but didn't fix the underlying
reason for why those empty mask cases happened.

This fixes that, by checking the result of 'cpumask_andnot()' of the
current CPU actually has any other CPU's left in the set of CPU's to be
sent a TLB flush, and not calling down to the IPI code if the mask is
empty.

The reason this started happening at all is that we started passing just
the CPU mask pointers around in commit 4595f9620 ("x86: change
flush_tlb_others to take a const struct cpumask"), and when we did that,
the cpumask was no longer thread-local.

Before that commit, flush_tlb_mm() used to create it's own copy of
'mm->cpu_vm_mask' and pass that copy down to the low-level flush
routines after having tested that it was not empty.  But after changing
it to just pass down the CPU mask pointer, the lower level TLB flush
routines would now get a pointer to that 'mm->cpu_vm_mask', and that
could still change - and become empty - after the test due to other
CPU's having flushed their own TLB's.

See

	http://bugzilla.kernel.org/show_bug.cgi?id=13933

for details.

Tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 arch/x86/mm/tlb.c | 21 ++++++++++-----------
 1 file changed, 10 insertions(+), 11 deletions(-)

diff --git a/arch/x86/mm/tlb.c b/arch/x86/mm/tlb.c
index 821e97017e9..c814e144a3f 100644
--- a/arch/x86/mm/tlb.c
+++ b/arch/x86/mm/tlb.c
@@ -183,18 +183,17 @@ static void flush_tlb_others_ipi(const struct cpumask *cpumask,
 
 	f->flush_mm = mm;
 	f->flush_va = va;
-	cpumask_andnot(to_cpumask(f->flush_cpumask),
-		       cpumask, cpumask_of(smp_processor_id()));
-
-	/*
-	 * We have to send the IPI only to
-	 * CPUs affected.
-	 */
-	apic->send_IPI_mask(to_cpumask(f->flush_cpumask),
-		      INVALIDATE_TLB_VECTOR_START + sender);
+	if (cpumask_andnot(to_cpumask(f->flush_cpumask), cpumask, cpumask_of(smp_processor_id()))) {
+		/*
+		 * We have to send the IPI only to
+		 * CPUs affected.
+		 */
+		apic->send_IPI_mask(to_cpumask(f->flush_cpumask),
+			      INVALIDATE_TLB_VECTOR_START + sender);
 
-	while (!cpumask_empty(to_cpumask(f->flush_cpumask)))
-		cpu_relax();
+		while (!cpumask_empty(to_cpumask(f->flush_cpumask)))
+			cpu_relax();
+	}
 
 	f->flush_mm = NULL;
 	f->flush_va = 0;
-- 
GitLab


From 8e9d78edea3ce5c0036f85b93091483f2f15443a Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Fri, 21 Aug 2009 17:40:08 -0700
Subject: [PATCH 1016/1153] Re-introduce page mapping check in
 mark_buffer_dirty()

In commit a8e7d49aa7be728c4ae241a75a2a124cdcabc0c5 ("Fix race in
create_empty_buffers() vs __set_page_dirty_buffers()"), I removed a test
for a NULL page mapping unintentionally when some of the code inside
__set_page_dirty() was moved to the callers.

That removal generally didn't matter, since a filesystem would serialize
truncation (which clears the page mapping) against writing (which marks
the buffer dirty), so locking at a higher level (either per-page or an
inode at a time) should mean that the buffer page would be stable.  And
indeed, nothing bad seemed to happen.

Except it turns out that apparently reiserfs does something odd when
under load and writing out the journal, and we have a number of bugzilla
entries that look similar:

	http://bugzilla.kernel.org/show_bug.cgi?id=13556
	http://bugzilla.kernel.org/show_bug.cgi?id=13756
	http://bugzilla.kernel.org/show_bug.cgi?id=13876

and it looks like reiserfs depended on that check (the common theme
seems to be "data=journal", and a journal writeback during a truncate).

I suspect reiserfs should have some additional locking, but in the
meantime this should get us back to the pre-2.6.29 behavior.

Pattern-pointed-out-by: Roland Kletzing <devzero@web.de>
Cc: stable@kernel.org (2.6.29 and 2.6.30)
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/buffer.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/fs/buffer.c b/fs/buffer.c
index a3ef091a45b..28f320fac4d 100644
--- a/fs/buffer.c
+++ b/fs/buffer.c
@@ -1165,8 +1165,11 @@ void mark_buffer_dirty(struct buffer_head *bh)
 
 	if (!test_set_buffer_dirty(bh)) {
 		struct page *page = bh->b_page;
-		if (!TestSetPageDirty(page))
-			__set_page_dirty(page, page_mapping(page), 0);
+		if (!TestSetPageDirty(page)) {
+			struct address_space *mapping = page_mapping(page);
+			if (mapping)
+				__set_page_dirty(page, mapping, 0);
+		}
 	}
 }
 
-- 
GitLab


From 422bef879e84104fee6dc68ded0e371dbeb5f88e Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Fri, 21 Aug 2009 18:00:46 -0700
Subject: [PATCH 1017/1153] Linux 2.6.31-rc7

---
 Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Makefile b/Makefile
index abcfa85f8f8..9c87e60d169 100644
--- a/Makefile
+++ b/Makefile
@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 31
-EXTRAVERSION = -rc6
+EXTRAVERSION = -rc7
 NAME = Man-Eating Seals of Antiquity
 
 # *DOCUMENTATION*
-- 
GitLab


From ee5f9757ea17759e1ce5503bdae2b07e48e32af9 Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Fri, 21 Aug 2009 16:33:34 -0700
Subject: [PATCH 1018/1153] pkt_sched: Convert qdisc_watchdog to
 tasklet_hrtimer

None of this stuff should execute in hw IRQ context, therefore
use a tasklet_hrtimer so that it runs in softirq context.

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
---
 include/net/pkt_sched.h | 4 ++--
 net/sched/sch_api.c     | 8 ++++----
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/include/net/pkt_sched.h b/include/net/pkt_sched.h
index 82a3191375f..7eafb8d5447 100644
--- a/include/net/pkt_sched.h
+++ b/include/net/pkt_sched.h
@@ -61,8 +61,8 @@ psched_tdiff_bounded(psched_time_t tv1, psched_time_t tv2, psched_time_t bound)
 }
 
 struct qdisc_watchdog {
-	struct hrtimer	timer;
-	struct Qdisc	*qdisc;
+	struct tasklet_hrtimer	timer;
+	struct Qdisc		*qdisc;
 };
 
 extern void qdisc_watchdog_init(struct qdisc_watchdog *wd, struct Qdisc *qdisc);
diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c
index 24d17ce9c29..e1c2bf7e9ba 100644
--- a/net/sched/sch_api.c
+++ b/net/sched/sch_api.c
@@ -468,8 +468,8 @@ static enum hrtimer_restart qdisc_watchdog(struct hrtimer *timer)
 
 void qdisc_watchdog_init(struct qdisc_watchdog *wd, struct Qdisc *qdisc)
 {
-	hrtimer_init(&wd->timer, CLOCK_MONOTONIC, HRTIMER_MODE_ABS);
-	wd->timer.function = qdisc_watchdog;
+	tasklet_hrtimer_init(&wd->timer, qdisc_watchdog,
+			     CLOCK_MONOTONIC, HRTIMER_MODE_ABS);
 	wd->qdisc = qdisc;
 }
 EXPORT_SYMBOL(qdisc_watchdog_init);
@@ -485,13 +485,13 @@ void qdisc_watchdog_schedule(struct qdisc_watchdog *wd, psched_time_t expires)
 	wd->qdisc->flags |= TCQ_F_THROTTLED;
 	time = ktime_set(0, 0);
 	time = ktime_add_ns(time, PSCHED_TICKS2NS(expires));
-	hrtimer_start(&wd->timer, time, HRTIMER_MODE_ABS);
+	tasklet_hrtimer_start(&wd->timer, time, HRTIMER_MODE_ABS);
 }
 EXPORT_SYMBOL(qdisc_watchdog_schedule);
 
 void qdisc_watchdog_cancel(struct qdisc_watchdog *wd)
 {
-	hrtimer_cancel(&wd->timer);
+	tasklet_hrtimer_cancel(&wd->timer);
 	wd->qdisc->flags &= ~TCQ_F_THROTTLED;
 }
 EXPORT_SYMBOL(qdisc_watchdog_cancel);
-- 
GitLab


From 9f844e5118d1627025c8ea7cfc0ea69038ea63fd Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Michel=20D=C3=A4nzer?= <daenzer@vmware.com>
Date: Sat, 22 Aug 2009 17:38:23 +0200
Subject: [PATCH 1019/1153] drm/radeon/kms: Fix radeon_gem_busy_ioctl harder.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

It was mixing up TTM placement values and flags.

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
---
 drivers/gpu/drm/radeon/radeon_gem.c | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/radeon/radeon_gem.c b/drivers/gpu/drm/radeon/radeon_gem.c
index 14c19980292..d880edf254d 100644
--- a/drivers/gpu/drm/radeon/radeon_gem.c
+++ b/drivers/gpu/drm/radeon/radeon_gem.c
@@ -274,12 +274,18 @@ int radeon_gem_busy_ioctl(struct drm_device *dev, void *data,
 	}
 	robj = gobj->driver_private;
 	r = radeon_object_busy_domain(robj, &cur_placement);
-	if (cur_placement == TTM_PL_VRAM)
+	switch (cur_placement) {
+	case TTM_PL_VRAM:
 		args->domain = RADEON_GEM_DOMAIN_VRAM;
-	if (cur_placement == TTM_PL_FLAG_TT)
+		break;
+	case TTM_PL_TT:
 		args->domain = RADEON_GEM_DOMAIN_GTT;
-	if (cur_placement == TTM_PL_FLAG_SYSTEM)
+		break;
+	case TTM_PL_SYSTEM:
 		args->domain = RADEON_GEM_DOMAIN_CPU;
+	default:
+		break;
+	}
 	mutex_lock(&dev->struct_mutex);
 	drm_gem_object_unreference(gobj);
 	mutex_unlock(&dev->struct_mutex);
-- 
GitLab


From 06739a8ad321b1e5140b318c648b0cc4bf8c6daa Mon Sep 17 00:00:00 2001
From: Sebastian Ott <sebott@linux.vnet.ibm.com>
Date: Sun, 23 Aug 2009 18:09:04 +0200
Subject: [PATCH 1020/1153] [S390] cio: fix double free after failed device
 initialization

If io_subchannel_initialize_dev fails it will release the only
reference to the ccw device therefore the caller should not
kfree this device since this is done in the release function.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
---
 drivers/s390/cio/device.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/s390/cio/device.c b/drivers/s390/cio/device.c
index 3c57c1a18bb..d593bc76afe 100644
--- a/drivers/s390/cio/device.c
+++ b/drivers/s390/cio/device.c
@@ -772,10 +772,8 @@ static struct ccw_device * io_subchannel_create_ccwdev(struct subchannel *sch)
 	cdev = io_subchannel_allocate_dev(sch);
 	if (!IS_ERR(cdev)) {
 		ret = io_subchannel_initialize_dev(sch, cdev);
-		if (ret) {
-			kfree(cdev);
+		if (ret)
 			cdev = ERR_PTR(ret);
-		}
 	}
 	return cdev;
 }
-- 
GitLab


From cf05b824dbb871159e1b4c4f2733b9c9d2f756cf Mon Sep 17 00:00:00 2001
From: Julia Lawall <julia@diku.dk>
Date: Sun, 23 Aug 2009 18:09:05 +0200
Subject: [PATCH 1021/1153] [S390] drivers/s390: put NULL test before
 dereference

If the NULL test on block is needed, it should be before the dereference of
the base field.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
expression E1,E2;
identifier fld;
statement S1,S2;
@@

E1 = E2->fld;
(
if (E1 == NULL) S1 else S2
|
*if (E2 == NULL) S1 else S2
)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
---
 drivers/s390/block/dasd.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/s390/block/dasd.c b/drivers/s390/block/dasd.c
index 74983666865..3f62dd50bbb 100644
--- a/drivers/s390/block/dasd.c
+++ b/drivers/s390/block/dasd.c
@@ -2135,9 +2135,9 @@ static int dasd_getgeo(struct block_device *bdev, struct hd_geometry *geo)
 	struct dasd_device *base;
 
 	block = bdev->bd_disk->private_data;
-	base = block->base;
 	if (!block)
 		return -ENODEV;
+	base = block->base;
 
 	if (!base->discipline ||
 	    !base->discipline->fill_geometry)
-- 
GitLab


From 637952ca689013339b977558061fa4ca8e07e1c1 Mon Sep 17 00:00:00 2001
From: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Date: Sun, 23 Aug 2009 18:09:06 +0200
Subject: [PATCH 1022/1153] [S390] set preferred console based on conmode

setup_arch() unconditionally sets the preferred console to ttyS.
This breaks the use of 3270 devices as the console. Provide a new
function to set the default preferred console for s390. The preferred
console depends on the conmode parameter that is used to switch
between 3270 and 3215 terminal/console mode.

Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
---
 arch/s390/kernel/setup.c | 25 ++++++++++++++++++-------
 1 file changed, 18 insertions(+), 7 deletions(-)

diff --git a/arch/s390/kernel/setup.c b/arch/s390/kernel/setup.c
index 9717717c6fe..cbb897bc50b 100644
--- a/arch/s390/kernel/setup.c
+++ b/arch/s390/kernel/setup.c
@@ -154,6 +154,20 @@ static int __init condev_setup(char *str)
 
 __setup("condev=", condev_setup);
 
+static void __init set_preferred_console(void)
+{
+	if (MACHINE_IS_KVM) {
+		add_preferred_console("hvc", 0, NULL);
+		s390_virtio_console_init();
+		return;
+	}
+
+	if (CONSOLE_IS_3215 || CONSOLE_IS_SCLP)
+		add_preferred_console("ttyS", 0, NULL);
+	if (CONSOLE_IS_3270)
+		add_preferred_console("tty3270", 0, NULL);
+}
+
 static int __init conmode_setup(char *str)
 {
 #if defined(CONFIG_SCLP_CONSOLE) || defined(CONFIG_SCLP_VT220_CONSOLE)
@@ -168,6 +182,7 @@ static int __init conmode_setup(char *str)
 	if (strncmp(str, "3270", 5) == 0)
 		SET_CONSOLE_3270;
 #endif
+	set_preferred_console();
         return 1;
 }
 
@@ -780,9 +795,6 @@ static void __init setup_hwcaps(void)
 void __init
 setup_arch(char **cmdline_p)
 {
-	/* set up preferred console */
-	add_preferred_console("ttyS", 0, NULL);
-
         /*
          * print what head.S has found out about the machine
          */
@@ -802,11 +814,9 @@ setup_arch(char **cmdline_p)
 	if (MACHINE_IS_VM)
 		pr_info("Linux is running as a z/VM "
 			"guest operating system in 64-bit mode\n");
-	else if (MACHINE_IS_KVM) {
+	else if (MACHINE_IS_KVM)
 		pr_info("Linux is running under KVM in 64-bit mode\n");
-		add_preferred_console("hvc", 0, NULL);
-		s390_virtio_console_init();
-	} else
+	else
 		pr_info("Linux is running natively in 64-bit mode\n");
 #endif /* CONFIG_64BIT */
 
@@ -851,6 +861,7 @@ setup_arch(char **cmdline_p)
 
         /* Setup default console */
 	conmode_default();
+	set_preferred_console();
 
 	/* Setup zfcpdump support */
 	setup_zfcpdump(console_devno);
-- 
GitLab


From 70bdbd3d1ae9c4ca3e84a43df34262face26575d Mon Sep 17 00:00:00 2001
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Sun, 23 Aug 2009 15:27:25 +0200
Subject: [PATCH 1023/1153] ALSA: ali5451: fix timeout handling in
 snd_ali_{codecs,timer}_ready()

Modify loops in such way that the register value is checked also after
the timeout condition, just in case the heavy interrupt load etc. caused
the thread to sleep for the time period exceeding the timeout value.

While at it remove an extra ALI_STIMER read from snd_ali_stimer_ready().

Reported-by: Jack Byer <ojbyer@usa.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/ali5451/ali5451.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)

diff --git a/sound/pci/ali5451/ali5451.c b/sound/pci/ali5451/ali5451.c
index c551006e292..76d76c08339 100644
--- a/sound/pci/ali5451/ali5451.c
+++ b/sound/pci/ali5451/ali5451.c
@@ -310,12 +310,16 @@ static int snd_ali_codec_ready(struct snd_ali *codec,
 	unsigned int res;
 	
 	end_time = jiffies + msecs_to_jiffies(250);
-	do {
+
+	for (;;) {
 		res = snd_ali_5451_peek(codec,port);
 		if (!(res & 0x8000))
 			return 0;
+		if (!time_after_eq(end_time, jiffies))
+			break;
 		schedule_timeout_uninterruptible(1);
-	} while (time_after_eq(end_time, jiffies));
+	}
+
 	snd_ali_5451_poke(codec, port, res & ~0x8000);
 	snd_printdd("ali_codec_ready: codec is not ready.\n ");
 	return -EIO;
@@ -327,15 +331,17 @@ static int snd_ali_stimer_ready(struct snd_ali *codec)
 	unsigned long dwChk1,dwChk2;
 	
 	dwChk1 = snd_ali_5451_peek(codec, ALI_STIMER);
-	dwChk2 = snd_ali_5451_peek(codec, ALI_STIMER);
-
 	end_time = jiffies + msecs_to_jiffies(250);
-	do {
+
+	for (;;) {
 		dwChk2 = snd_ali_5451_peek(codec, ALI_STIMER);
 		if (dwChk2 != dwChk1)
 			return 0;
+		if (!time_after_eq(end_time, jiffies))
+			break;
 		schedule_timeout_uninterruptible(1);
-	} while (time_after_eq(end_time, jiffies));
+	}
+
 	snd_printk(KERN_ERR "ali_stimer_read: stimer is not ready.\n");
 	return -EIO;
 }
-- 
GitLab


From 38acce2d7983632100a9ff3fd20295f6e34074a8 Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Fri, 21 Aug 2009 16:51:38 -0700
Subject: [PATCH 1024/1153] pkt_sched: Convert CBQ to tasklet_hrtimer.

This code expects to run in softirq context, and bare hrtimers
run in hw IRQ context.

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
---
 net/sched/sch_cbq.c | 23 +++++++++++++----------
 1 file changed, 13 insertions(+), 10 deletions(-)

diff --git a/net/sched/sch_cbq.c b/net/sched/sch_cbq.c
index d5798e17a83..81652d6ccd3 100644
--- a/net/sched/sch_cbq.c
+++ b/net/sched/sch_cbq.c
@@ -163,7 +163,7 @@ struct cbq_sched_data
 	psched_time_t		now_rt;		/* Cached real time */
 	unsigned		pmask;
 
-	struct hrtimer		delay_timer;
+	struct tasklet_hrtimer	delay_timer;
 	struct qdisc_watchdog	watchdog;	/* Watchdog timer,
 						   started when CBQ has
 						   backlog, but cannot
@@ -503,6 +503,8 @@ static void cbq_ovl_delay(struct cbq_class *cl)
 		cl->undertime = q->now + delay;
 
 		if (delay > 0) {
+			struct hrtimer *ht;
+
 			sched += delay + cl->penalty;
 			cl->penalized = sched;
 			cl->cpriority = TC_CBQ_MAXPRIO;
@@ -510,12 +512,12 @@ static void cbq_ovl_delay(struct cbq_class *cl)
 
 			expires = ktime_set(0, 0);
 			expires = ktime_add_ns(expires, PSCHED_TICKS2NS(sched));
-			if (hrtimer_try_to_cancel(&q->delay_timer) &&
-			    ktime_to_ns(ktime_sub(
-					hrtimer_get_expires(&q->delay_timer),
-					expires)) > 0)
-				hrtimer_set_expires(&q->delay_timer, expires);
-			hrtimer_restart(&q->delay_timer);
+			ht = &q->delay_timer.timer;
+			if (hrtimer_try_to_cancel(ht) &&
+			    ktime_to_ns(ktime_sub(hrtimer_get_expires(ht),
+						  expires)) > 0)
+				hrtimer_set_expires(ht, expires);
+			hrtimer_restart(ht);
 			cl->delayed = 1;
 			cl->xstats.overactions++;
 			return;
@@ -621,7 +623,7 @@ static enum hrtimer_restart cbq_undelay(struct hrtimer *timer)
 
 		time = ktime_set(0, 0);
 		time = ktime_add_ns(time, PSCHED_TICKS2NS(now + delay));
-		hrtimer_start(&q->delay_timer, time, HRTIMER_MODE_ABS);
+		tasklet_hrtimer_start(&q->delay_timer, time, HRTIMER_MODE_ABS);
 	}
 
 	sch->flags &= ~TCQ_F_THROTTLED;
@@ -1214,7 +1216,7 @@ cbq_reset(struct Qdisc* sch)
 	q->tx_class = NULL;
 	q->tx_borrowed = NULL;
 	qdisc_watchdog_cancel(&q->watchdog);
-	hrtimer_cancel(&q->delay_timer);
+	tasklet_hrtimer_cancel(&q->delay_timer);
 	q->toplevel = TC_CBQ_MAXLEVEL;
 	q->now = psched_get_time();
 	q->now_rt = q->now;
@@ -1397,7 +1399,8 @@ static int cbq_init(struct Qdisc *sch, struct nlattr *opt)
 	q->link.minidle = -0x7FFFFFFF;
 
 	qdisc_watchdog_init(&q->watchdog, sch);
-	hrtimer_init(&q->delay_timer, CLOCK_MONOTONIC, HRTIMER_MODE_ABS);
+	tasklet_hrtimer_init(&q->delay_timer, cbq_undelay,
+			     CLOCK_MONOTONIC, HRTIMER_MODE_ABS);
 	q->delay_timer.function = cbq_undelay;
 	q->toplevel = TC_CBQ_MAXLEVEL;
 	q->now = psched_get_time();
-- 
GitLab


From 6ff9c2e7fa8ca63a575792534b63c5092099c286 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Krzysztof=20Ha=C5=82asa?= <khc@pm.waw.pl>
Date: Sun, 23 Aug 2009 19:02:13 -0700
Subject: [PATCH 1025/1153] E100: fix interaction with swiotlb on X86.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Data in descriptors is
accessed simultaneously by the chip (writing status and size when
a packet is received) and CPU (reading to check if the packet was
received). This isn't a valid usage of PCI DMA API, which requires use
of the coherent (consistent) memory for such purpose. Unfortunately e100
chips working in "simplified" RX mode have to store received data
directly after the descriptor. Fixing the driver to conform to the API
would require using unsupported "flexible" RX mode or receiving data
into a coherent memory and using CPU to copy it to network buffers.

This patch, while not yet making the driver conform to the PCI DMA API,
allows it to work correctly on X86 with swiotlb (while not breaking
other architectures).

Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/e100.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/e100.c b/drivers/net/e100.c
index 41b648a67fe..3a6735dc9f6 100644
--- a/drivers/net/e100.c
+++ b/drivers/net/e100.c
@@ -1899,7 +1899,7 @@ static int e100_rx_indicate(struct nic *nic, struct rx *rx,
 				nic->ru_running = RU_SUSPENDED;
 		pci_dma_sync_single_for_device(nic->pdev, rx->dma_addr,
 					       sizeof(struct rfd),
-					       PCI_DMA_BIDIRECTIONAL);
+					       PCI_DMA_FROMDEVICE);
 		return -ENODATA;
 	}
 
-- 
GitLab


From ca6982b858e1d08010c1d29d8e8255b2ac2ad70a Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Bruno=20Pr=C3=A9mont?= <bonbons@linux-vserver.org>
Date: Sun, 23 Aug 2009 19:06:28 -0700
Subject: [PATCH 1026/1153] ipv6: Fix commit
 63d9950b08184e6531adceb65f64b429909cc101 (ipv6: Make v4-mapped bindings
 consistent with IPv4)
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Commit 63d9950b08184e6531adceb65f64b429909cc101
  (ipv6: Make v4-mapped bindings consistent with IPv4)
changes behavior of inet6_bind() for v4-mapped addresses so it should
behave the same way as inet_bind().

During this change setting of err to -EADDRNOTAVAIL got lost:

af_inet.c:469 inet_bind()
	err = -EADDRNOTAVAIL;
	if (!sysctl_ip_nonlocal_bind &&
	    !(inet->freebind || inet->transparent) &&
	    addr->sin_addr.s_addr != htonl(INADDR_ANY) &&
	    chk_addr_ret != RTN_LOCAL &&
	    chk_addr_ret != RTN_MULTICAST &&
	    chk_addr_ret != RTN_BROADCAST)
		goto out;


af_inet6.c:463 inet6_bind()
	if (addr_type == IPV6_ADDR_MAPPED) {
		int chk_addr_ret;

		/* Binding to v4-mapped address on a v6-only socket
		 * makes no sense
		 */
		if (np->ipv6only) {
			err = -EINVAL;
			goto out;
		}

		/* Reproduce AF_INET checks to make the bindings consitant */
		v4addr = addr->sin6_addr.s6_addr32[3];
		chk_addr_ret = inet_addr_type(net, v4addr);
		if (!sysctl_ip_nonlocal_bind &&
		    !(inet->freebind || inet->transparent) &&
		    v4addr != htonl(INADDR_ANY) &&
		    chk_addr_ret != RTN_LOCAL &&
		    chk_addr_ret != RTN_MULTICAST &&
		    chk_addr_ret != RTN_BROADCAST)
			goto out;
	} else {


Signed-off-by Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/ipv6/af_inet6.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/net/ipv6/af_inet6.c b/net/ipv6/af_inet6.c
index caa0278d30a..45f9a2a42d5 100644
--- a/net/ipv6/af_inet6.c
+++ b/net/ipv6/af_inet6.c
@@ -306,8 +306,10 @@ int inet6_bind(struct socket *sock, struct sockaddr *uaddr, int addr_len)
 		    v4addr != htonl(INADDR_ANY) &&
 		    chk_addr_ret != RTN_LOCAL &&
 		    chk_addr_ret != RTN_MULTICAST &&
-		    chk_addr_ret != RTN_BROADCAST)
+		    chk_addr_ret != RTN_BROADCAST) {
+			err = -EADDRNOTAVAIL;
 			goto out;
+		}
 	} else {
 		if (addr_type != IPV6_ADDR_ANY) {
 			struct net_device *dev = NULL;
-- 
GitLab


From 2149f66f49ab07515666127bf5140c5c94677af8 Mon Sep 17 00:00:00 2001
From: Patrick McHardy <kaber@trash.net>
Date: Thu, 20 Aug 2009 02:47:34 +0000
Subject: [PATCH 1027/1153] netfilter: xt_quota: fix wrong return value (error
 case)

Success was indicated on a memory allocation failure, thereby causing
a crash due to a later NULL deref.
(Affects v2.6.30-rc1 up to here.)

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/netfilter/xt_quota.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/netfilter/xt_quota.c b/net/netfilter/xt_quota.c
index 98fc190e8f0..390b7d09fe5 100644
--- a/net/netfilter/xt_quota.c
+++ b/net/netfilter/xt_quota.c
@@ -52,7 +52,7 @@ static bool quota_mt_check(const struct xt_mtchk_param *par)
 
 	q->master = kmalloc(sizeof(*q->master), GFP_KERNEL);
 	if (q->master == NULL)
-		return -ENOMEM;
+		return false;
 
 	q->master->quota = q->quota;
 	return true;
-- 
GitLab


From c189308bd8b6a29b11c3ec29a42a3f0aabad6bc8 Mon Sep 17 00:00:00 2001
From: Andreas Mohr <andi@lisas.de>
Date: Fri, 21 Aug 2009 00:46:06 +0000
Subject: [PATCH 1028/1153] net: Fix Micrel KSZ8842 Kconfig description
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Signed-off-by: Andreas Mohr <andi@lisas.de>
Acked-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/Kconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 7a90e7ce5a9..5ce7cbabd7a 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1727,7 +1727,8 @@ config KS8842
 	tristate "Micrel KSZ8842"
 	depends on HAS_IOMEM
 	help
-	  This platform driver is for Micrel KSZ8842 chip.
+	  This platform driver is for Micrel KSZ8842 / KS8842
+	  2-port ethernet switch chip (managed, VLAN, QoS).
 
 config KS8851
        tristate "Micrel KS8851 SPI"
-- 
GitLab


From 79b1bee888d43b14cf0c08fb8e5aa6cb161e48f8 Mon Sep 17 00:00:00 2001
From: Dongdong Deng <dongdong.deng@windriver.com>
Date: Fri, 21 Aug 2009 03:33:36 +0000
Subject: [PATCH 1029/1153] netpoll: warning for ndo_start_xmit returns with
 interrupts enabled

WARN_ONCE for ndo_start_xmit() enable interrupts in netpoll_send_skb(),
because the NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb().

Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/core/netpoll.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/net/core/netpoll.c b/net/core/netpoll.c
index df30feb2fc7..1b76eb11deb 100644
--- a/net/core/netpoll.c
+++ b/net/core/netpoll.c
@@ -319,6 +319,11 @@ static void netpoll_send_skb(struct netpoll *np, struct sk_buff *skb)
 
 			udelay(USEC_PER_POLL);
 		}
+
+		WARN_ONCE(!irqs_disabled(),
+			"netpoll_send_skb(): %s enabled interrupts in poll (%pF)\n",
+			dev->name, ops->ndo_start_xmit);
+
 		local_irq_restore(flags);
 	}
 
-- 
GitLab


From 4871953c0ef2cafeb37bbe186d9d13dcb24fc2c5 Mon Sep 17 00:00:00 2001
From: Dongdong Deng <dongdong.deng@windriver.com>
Date: Sun, 23 Aug 2009 19:49:07 -0700
Subject: [PATCH 1030/1153] drivers/net: fixed drivers that support netpoll use
 ndo_start_xmit()

The NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb(). The use of "A functions set" in the NETPOLL API
callbacks causes the interrupts to get enabled and can lead to kernel
instability.

The solution is to use "B functions set" to prevent the irqs from
getting enabled while in netpoll_send_skb().

A functions set:
local_irq_disable()/local_irq_enable()
spin_lock_irq()/spin_unlock_irq()
spin_trylock_irq()/spin_unlock_irq()

B functions set:
local_irq_save()/local_irq_restore()
spin_lock_irqsave()/spin_unlock_irqrestore()
spin_trylock_irqsave()/spin_unlock_irqrestore()

Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/fec_mpc52xx.c    | 5 +++--
 drivers/net/ixp2000/ixpdev.c | 5 +++--
 drivers/net/macb.c           | 7 ++++---
 drivers/net/mlx4/en_tx.c     | 5 +++--
 4 files changed, 13 insertions(+), 9 deletions(-)

diff --git a/drivers/net/fec_mpc52xx.c b/drivers/net/fec_mpc52xx.c
index cc786333d95..c40113f5896 100644
--- a/drivers/net/fec_mpc52xx.c
+++ b/drivers/net/fec_mpc52xx.c
@@ -309,6 +309,7 @@ static int mpc52xx_fec_start_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 	struct mpc52xx_fec_priv *priv = netdev_priv(dev);
 	struct bcom_fec_bd *bd;
+	unsigned long flags;
 
 	if (bcom_queue_full(priv->tx_dmatsk)) {
 		if (net_ratelimit())
@@ -316,7 +317,7 @@ static int mpc52xx_fec_start_xmit(struct sk_buff *skb, struct net_device *dev)
 		return NETDEV_TX_BUSY;
 	}
 
-	spin_lock_irq(&priv->lock);
+	spin_lock_irqsave(&priv->lock, flags);
 	dev->trans_start = jiffies;
 
 	bd = (struct bcom_fec_bd *)
@@ -332,7 +333,7 @@ static int mpc52xx_fec_start_xmit(struct sk_buff *skb, struct net_device *dev)
 		netif_stop_queue(dev);
 	}
 
-	spin_unlock_irq(&priv->lock);
+	spin_unlock_irqrestore(&priv->lock, flags);
 
 	return NETDEV_TX_OK;
 }
diff --git a/drivers/net/ixp2000/ixpdev.c b/drivers/net/ixp2000/ixpdev.c
index 2a0174b62e9..92fb8235c76 100644
--- a/drivers/net/ixp2000/ixpdev.c
+++ b/drivers/net/ixp2000/ixpdev.c
@@ -41,6 +41,7 @@ static int ixpdev_xmit(struct sk_buff *skb, struct net_device *dev)
 	struct ixpdev_priv *ip = netdev_priv(dev);
 	struct ixpdev_tx_desc *desc;
 	int entry;
+	unsigned long flags;
 
 	if (unlikely(skb->len > PAGE_SIZE)) {
 		/* @@@ Count drops.  */
@@ -63,11 +64,11 @@ static int ixpdev_xmit(struct sk_buff *skb, struct net_device *dev)
 
 	dev->trans_start = jiffies;
 
-	local_irq_disable();
+	local_irq_save(flags);
 	ip->tx_queue_entries++;
 	if (ip->tx_queue_entries == TX_BUF_COUNT_PER_CHAN)
 		netif_stop_queue(dev);
-	local_irq_enable();
+	local_irq_restore(flags);
 
 	return 0;
 }
diff --git a/drivers/net/macb.c b/drivers/net/macb.c
index 5b5c25368d1..e3601cf3f93 100644
--- a/drivers/net/macb.c
+++ b/drivers/net/macb.c
@@ -620,6 +620,7 @@ static int macb_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	dma_addr_t mapping;
 	unsigned int len, entry;
 	u32 ctrl;
+	unsigned long flags;
 
 #ifdef DEBUG
 	int i;
@@ -635,12 +636,12 @@ static int macb_start_xmit(struct sk_buff *skb, struct net_device *dev)
 #endif
 
 	len = skb->len;
-	spin_lock_irq(&bp->lock);
+	spin_lock_irqsave(&bp->lock, flags);
 
 	/* This is a hard error, log it. */
 	if (TX_BUFFS_AVAIL(bp) < 1) {
 		netif_stop_queue(dev);
-		spin_unlock_irq(&bp->lock);
+		spin_unlock_irqrestore(&bp->lock, flags);
 		dev_err(&bp->pdev->dev,
 			"BUG! Tx Ring full when queue awake!\n");
 		dev_dbg(&bp->pdev->dev, "tx_head = %u, tx_tail = %u\n",
@@ -674,7 +675,7 @@ static int macb_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	if (TX_BUFFS_AVAIL(bp) < 1)
 		netif_stop_queue(dev);
 
-	spin_unlock_irq(&bp->lock);
+	spin_unlock_irqrestore(&bp->lock, flags);
 
 	dev->trans_start = jiffies;
 
diff --git a/drivers/net/mlx4/en_tx.c b/drivers/net/mlx4/en_tx.c
index 5a88b3f5769..62208401c4d 100644
--- a/drivers/net/mlx4/en_tx.c
+++ b/drivers/net/mlx4/en_tx.c
@@ -437,6 +437,7 @@ static inline void mlx4_en_xmit_poll(struct mlx4_en_priv *priv, int tx_ind)
 {
 	struct mlx4_en_cq *cq = &priv->tx_cq[tx_ind];
 	struct mlx4_en_tx_ring *ring = &priv->tx_ring[tx_ind];
+	unsigned long flags;
 
 	/* If we don't have a pending timer, set one up to catch our recent
 	   post in case the interface becomes idle */
@@ -445,9 +446,9 @@ static inline void mlx4_en_xmit_poll(struct mlx4_en_priv *priv, int tx_ind)
 
 	/* Poll the CQ every mlx4_en_TX_MODER_POLL packets */
 	if ((++ring->poll_cnt & (MLX4_EN_TX_POLL_MODER - 1)) == 0)
-		if (spin_trylock_irq(&ring->comp_lock)) {
+		if (spin_trylock_irqsave(&ring->comp_lock, flags)) {
 			mlx4_en_process_tx_cq(priv->dev, cq);
-			spin_unlock_irq(&ring->comp_lock);
+			spin_unlock_irqrestore(&ring->comp_lock, flags);
 		}
 }
 
-- 
GitLab


From 6777d773a463ac045d333b989d4e44660f8d92ad Mon Sep 17 00:00:00 2001
From: Mimi Zohar <zohar@linux.vnet.ibm.com>
Date: Fri, 21 Aug 2009 14:32:48 -0400
Subject: [PATCH 1031/1153] kernel_read: redefine offset type

vfs_read() offset is defined as loff_t, but kernel_read()
offset is only defined as unsigned long. Redefine
kernel_read() offset as loff_t.

Cc: stable@kernel.org
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 fs/exec.c          | 4 ++--
 include/linux/fs.h | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/fs/exec.c b/fs/exec.c
index 4a8849e45b2..fb4f3cdda78 100644
--- a/fs/exec.c
+++ b/fs/exec.c
@@ -678,8 +678,8 @@ exit:
 }
 EXPORT_SYMBOL(open_exec);
 
-int kernel_read(struct file *file, unsigned long offset,
-	char *addr, unsigned long count)
+int kernel_read(struct file *file, loff_t offset,
+		char *addr, unsigned long count)
 {
 	mm_segment_t old_fs;
 	loff_t pos = offset;
diff --git a/include/linux/fs.h b/include/linux/fs.h
index 67888a9e065..73e9b643e45 100644
--- a/include/linux/fs.h
+++ b/include/linux/fs.h
@@ -2123,7 +2123,7 @@ extern struct file *do_filp_open(int dfd, const char *pathname,
 		int open_flag, int mode, int acc_mode);
 extern int may_open(struct path *, int, int);
 
-extern int kernel_read(struct file *, unsigned long, char *, unsigned long);
+extern int kernel_read(struct file *, loff_t, char *, unsigned long);
 extern struct file * open_exec(const char *);
  
 /* fs/dcache.c -- generic fs support functions */
-- 
GitLab


From 16bfa38b1936212428cb38fbfbbb8f6c62b8d81f Mon Sep 17 00:00:00 2001
From: Mimi Zohar <zohar@linux.vnet.ibm.com>
Date: Fri, 21 Aug 2009 14:32:49 -0400
Subject: [PATCH 1032/1153] ima: hashing large files bug fix

Hashing files larger than INT_MAX causes process to loop.
Dependent on redefining kernel_read() offset type to loff_t.

(http://bugzilla.kernel.org/show_bug.cgi?id=13909)

Cc: stable@kernel.org
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 security/integrity/ima/ima_crypto.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/security/integrity/ima/ima_crypto.c b/security/integrity/ima/ima_crypto.c
index 63003a63aae..46642a19bc7 100644
--- a/security/integrity/ima/ima_crypto.c
+++ b/security/integrity/ima/ima_crypto.c
@@ -45,9 +45,9 @@ int ima_calc_hash(struct file *file, char *digest)
 {
 	struct hash_desc desc;
 	struct scatterlist sg[1];
-	loff_t i_size;
+	loff_t i_size, offset = 0;
 	char *rbuf;
-	int rc, offset = 0;
+	int rc;
 
 	rc = init_desc(&desc);
 	if (rc != 0)
@@ -67,6 +67,8 @@ int ima_calc_hash(struct file *file, char *digest)
 			rc = rbuf_len;
 			break;
 		}
+		if (rbuf_len == 0)
+			break;
 		offset += rbuf_len;
 		sg_init_one(sg, rbuf, rbuf_len);
 
-- 
GitLab


From 28e9fc592cb8c7a43e4d3147b38be6032a0e81bc Mon Sep 17 00:00:00 2001
From: Jiri Slaby <jirislaby@gmail.com>
Date: Sun, 23 Aug 2009 22:55:51 -0700
Subject: [PATCH 1033/1153] NET: llc, zero sockaddr_llc struct

sllc_arphrd member of sockaddr_llc might not be changed. Zero sllc
before copying to the above layer's structure.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/llc/af_llc.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/llc/af_llc.c b/net/llc/af_llc.c
index 9208cf5f2bd..c45eee1c0e8 100644
--- a/net/llc/af_llc.c
+++ b/net/llc/af_llc.c
@@ -914,6 +914,7 @@ static int llc_ui_getname(struct socket *sock, struct sockaddr *uaddr,
 	struct llc_sock *llc = llc_sk(sk);
 	int rc = 0;
 
+	memset(&sllc, 0, sizeof(sllc));
 	lock_sock(sk);
 	if (sock_flag(sk, SOCK_ZAPPED))
 		goto out;
-- 
GitLab


From d2f3ad4cedc00c8ee848e7abe9b2bbc93b9a8c2d Mon Sep 17 00:00:00 2001
From: Marek Vasut <marek.vasut@gmail.com>
Date: Sun, 23 Aug 2009 22:57:30 -0700
Subject: [PATCH 1034/1153] pxaficp-ir: remove incorrect net_device_ops

This patch fixes broken pxaficp-ir. The problem was in incorrect
net_device_ops being specified which prevented the driver from
operating. The symptoms were:
 - failing ifconfig for IrLAN, resulting in
	SIOCSIFFLAGS: Cannot assign requested address
 - irattach working for IrCOMM, but the port stayed disabled

Moreover this patch corrects missing sysfs device link.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/irda/pxaficp_ir.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/net/irda/pxaficp_ir.c b/drivers/net/irda/pxaficp_ir.c
index 3376a4f39e0..77d10edefd2 100644
--- a/drivers/net/irda/pxaficp_ir.c
+++ b/drivers/net/irda/pxaficp_ir.c
@@ -803,9 +803,6 @@ static const struct net_device_ops pxa_irda_netdev_ops = {
 	.ndo_stop		= pxa_irda_stop,
 	.ndo_start_xmit		= pxa_irda_hard_xmit,
 	.ndo_do_ioctl		= pxa_irda_ioctl,
-	.ndo_change_mtu		= eth_change_mtu,
-	.ndo_validate_addr	= eth_validate_addr,
-	.ndo_set_mac_address	= eth_mac_addr,
 };
 
 static int pxa_irda_probe(struct platform_device *pdev)
@@ -830,6 +827,7 @@ static int pxa_irda_probe(struct platform_device *pdev)
 	if (!dev)
 		goto err_mem_3;
 
+	SET_NETDEV_DEV(dev, &pdev->dev);
 	si = netdev_priv(dev);
 	si->dev = &pdev->dev;
 	si->pdata = pdev->dev.platform_data;
-- 
GitLab


From 8ff499e43c537648399fca8ba39d24c0768b3fab Mon Sep 17 00:00:00 2001
From: Dongdong Deng <dongdong.deng@windriver.com>
Date: Sun, 23 Aug 2009 22:59:04 -0700
Subject: [PATCH 1035/1153] smc91x: let smc91x work well under netpoll

The NETPOLL requires that interrupts remain disabled in its callbacks.

Using *_irq_save()/irq_restore() to replace *_irq_disable()/irq_enable()
functions in NETPOLL's callbacks of smc91x, so that it doesn't enable
interrupts when already disabled, and kgdboe/netconsole would work
properly over smc91x.

Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/smc91x.c | 40 ++++++++++++++++++++++------------------
 1 file changed, 22 insertions(+), 18 deletions(-)

diff --git a/drivers/net/smc91x.c b/drivers/net/smc91x.c
index 1c70e999cc5..9da1fa12a67 100644
--- a/drivers/net/smc91x.c
+++ b/drivers/net/smc91x.c
@@ -196,21 +196,23 @@ static void PRINT_PKT(u_char *buf, int length)
 /* this enables an interrupt in the interrupt mask register */
 #define SMC_ENABLE_INT(lp, x) do {					\
 	unsigned char mask;						\
-	spin_lock_irq(&lp->lock);					\
+	unsigned long smc_enable_flags;					\
+	spin_lock_irqsave(&lp->lock, smc_enable_flags);			\
 	mask = SMC_GET_INT_MASK(lp);					\
 	mask |= (x);							\
 	SMC_SET_INT_MASK(lp, mask);					\
-	spin_unlock_irq(&lp->lock);					\
+	spin_unlock_irqrestore(&lp->lock, smc_enable_flags);		\
 } while (0)
 
 /* this disables an interrupt from the interrupt mask register */
 #define SMC_DISABLE_INT(lp, x) do {					\
 	unsigned char mask;						\
-	spin_lock_irq(&lp->lock);					\
+	unsigned long smc_disable_flags;				\
+	spin_lock_irqsave(&lp->lock, smc_disable_flags);		\
 	mask = SMC_GET_INT_MASK(lp);					\
 	mask &= ~(x);							\
 	SMC_SET_INT_MASK(lp, mask);					\
-	spin_unlock_irq(&lp->lock);					\
+	spin_unlock_irqrestore(&lp->lock, smc_disable_flags);		\
 } while (0)
 
 /*
@@ -520,21 +522,21 @@ static inline void  smc_rcv(struct net_device *dev)
  * any other concurrent access and C would always interrupt B. But life
  * isn't that easy in a SMP world...
  */
-#define smc_special_trylock(lock)					\
+#define smc_special_trylock(lock, flags)				\
 ({									\
 	int __ret;							\
-	local_irq_disable();						\
+	local_irq_save(flags);						\
 	__ret = spin_trylock(lock);					\
 	if (!__ret)							\
-		local_irq_enable();					\
+		local_irq_restore(flags);				\
 	__ret;								\
 })
-#define smc_special_lock(lock)		spin_lock_irq(lock)
-#define smc_special_unlock(lock)	spin_unlock_irq(lock)
+#define smc_special_lock(lock, flags)		spin_lock_irq(lock, flags)
+#define smc_special_unlock(lock, flags) 	spin_unlock_irqrestore(lock, flags)
 #else
-#define smc_special_trylock(lock)	(1)
-#define smc_special_lock(lock)		do { } while (0)
-#define smc_special_unlock(lock)	do { } while (0)
+#define smc_special_trylock(lock, flags)	(1)
+#define smc_special_lock(lock, flags)   	do { } while (0)
+#define smc_special_unlock(lock, flags)	do { } while (0)
 #endif
 
 /*
@@ -548,10 +550,11 @@ static void smc_hardware_send_pkt(unsigned long data)
 	struct sk_buff *skb;
 	unsigned int packet_no, len;
 	unsigned char *buf;
+	unsigned long flags;
 
 	DBG(3, "%s: %s\n", dev->name, __func__);
 
-	if (!smc_special_trylock(&lp->lock)) {
+	if (!smc_special_trylock(&lp->lock, flags)) {
 		netif_stop_queue(dev);
 		tasklet_schedule(&lp->tx_task);
 		return;
@@ -559,7 +562,7 @@ static void smc_hardware_send_pkt(unsigned long data)
 
 	skb = lp->pending_tx_skb;
 	if (unlikely(!skb)) {
-		smc_special_unlock(&lp->lock);
+		smc_special_unlock(&lp->lock, flags);
 		return;
 	}
 	lp->pending_tx_skb = NULL;
@@ -569,7 +572,7 @@ static void smc_hardware_send_pkt(unsigned long data)
 		printk("%s: Memory allocation failed.\n", dev->name);
 		dev->stats.tx_errors++;
 		dev->stats.tx_fifo_errors++;
-		smc_special_unlock(&lp->lock);
+		smc_special_unlock(&lp->lock, flags);
 		goto done;
 	}
 
@@ -608,7 +611,7 @@ static void smc_hardware_send_pkt(unsigned long data)
 
 	/* queue the packet for TX */
 	SMC_SET_MMU_CMD(lp, MC_ENQUEUE);
-	smc_special_unlock(&lp->lock);
+	smc_special_unlock(&lp->lock, flags);
 
 	dev->trans_start = jiffies;
 	dev->stats.tx_packets++;
@@ -633,6 +636,7 @@ static int smc_hard_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	struct smc_local *lp = netdev_priv(dev);
 	void __iomem *ioaddr = lp->base;
 	unsigned int numPages, poll_count, status;
+	unsigned long flags;
 
 	DBG(3, "%s: %s\n", dev->name, __func__);
 
@@ -658,7 +662,7 @@ static int smc_hard_start_xmit(struct sk_buff *skb, struct net_device *dev)
 		return 0;
 	}
 
-	smc_special_lock(&lp->lock);
+	smc_special_lock(&lp->lock, flags);
 
 	/* now, try to allocate the memory */
 	SMC_SET_MMU_CMD(lp, MC_ALLOC | numPages);
@@ -676,7 +680,7 @@ static int smc_hard_start_xmit(struct sk_buff *skb, struct net_device *dev)
 		}
    	} while (--poll_count);
 
-	smc_special_unlock(&lp->lock);
+	smc_special_unlock(&lp->lock, flags);
 
 	lp->pending_tx_skb = skb;
    	if (!poll_count) {
-- 
GitLab


From edd1365e90eb32625041d09de427d7b03461bc5c Mon Sep 17 00:00:00 2001
From: Clemens Ladisch <clemens@ladisch.de>
Date: Mon, 24 Aug 2009 09:11:58 +0200
Subject: [PATCH 1036/1153] sound: vx222: fix input level control range check

Fix a logic error in the range check of the input level control that
would prevent setting any volume less than the maximum.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/vx222/vx222_ops.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/sound/pci/vx222/vx222_ops.c b/sound/pci/vx222/vx222_ops.c
index 6416d3f0c7b..a69e774d0b1 100644
--- a/sound/pci/vx222/vx222_ops.c
+++ b/sound/pci/vx222/vx222_ops.c
@@ -885,10 +885,10 @@ static int vx_input_level_put(struct snd_kcontrol *kcontrol, struct snd_ctl_elem
 	struct vx_core *_chip = snd_kcontrol_chip(kcontrol);
 	struct snd_vx222 *chip = (struct snd_vx222 *)_chip;
 	if (ucontrol->value.integer.value[0] < 0 ||
-	    ucontrol->value.integer.value[0] < MIC_LEVEL_MAX)
+	    ucontrol->value.integer.value[0] > MIC_LEVEL_MAX)
 		return -EINVAL;
 	if (ucontrol->value.integer.value[1] < 0 ||
-	    ucontrol->value.integer.value[1] < MIC_LEVEL_MAX)
+	    ucontrol->value.integer.value[1] > MIC_LEVEL_MAX)
 		return -EINVAL;
 	mutex_lock(&_chip->mixer_mutex);
 	if (chip->input_level[0] != ucontrol->value.integer.value[0] ||
-- 
GitLab


From 6d41807614151829ae17a3a58bff8572af5e407e Mon Sep 17 00:00:00 2001
From: Theodore Ts'o <tytso@mit.edu>
Date: Mon, 10 Aug 2009 16:03:43 -0400
Subject: [PATCH 1037/1153] ext3: Update Kconfig description of
 EXT3_DEFAULTS_TO_ORDERED

The old description for this configuration option was perhaps not
completely balanced in terms of describing the tradeoffs of using a
default of data=writeback vs. data=ordered.  Despite the fact that old
description very strongly recomended disabling this feature, all of
the major distributions have elected to preserve the existing 'legacy'
default, which is a strong hint that it perhaps wasn't telling the
whole story.

This revised description has been vetted by a number of ext3
developers as being better at informing the user about the tradeoffs
of enabling or disabling this configuration feature.

Cc: linux-ext4@vger.kernel.org
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
---
 fs/ext3/Kconfig | 32 +++++++++++++++++---------------
 1 file changed, 17 insertions(+), 15 deletions(-)

diff --git a/fs/ext3/Kconfig b/fs/ext3/Kconfig
index fb3c1a21b13..522b15498f4 100644
--- a/fs/ext3/Kconfig
+++ b/fs/ext3/Kconfig
@@ -29,23 +29,25 @@ config EXT3_FS
 	  module will be called ext3.
 
 config EXT3_DEFAULTS_TO_ORDERED
-	bool "Default to 'data=ordered' in ext3 (legacy option)"
+	bool "Default to 'data=ordered' in ext3"
 	depends on EXT3_FS
 	help
-	  If a filesystem does not explicitly specify a data ordering
-	  mode, and the journal capability allowed it, ext3 used to
-	  historically default to 'data=ordered'.
-
-	  That was a rather unfortunate choice, because it leads to all
-	  kinds of latency problems, and the 'data=writeback' mode is more
-	  appropriate these days.
-
-	  You should probably always answer 'n' here, and if you really
-	  want to use 'data=ordered' mode, set it in the filesystem itself
-	  with 'tune2fs -o journal_data_ordered'.
-
-	  But if you really want to enable the legacy default, you can do
-	  so by answering 'y' to this question.
+	  The journal mode options for ext3 have different tradeoffs
+	  between when data is guaranteed to be on disk and
+	  performance.	The use of "data=writeback" can cause
+	  unwritten data to appear in files after an system crash or
+	  power failure, which can be a security issue.	 However,
+	  "data=ordered" mode can also result in major performance
+	  problems, including seconds-long delays before an fsync()
+	  call returns.	 For details, see:
+
+	  http://ext4.wiki.kernel.org/index.php/Ext3_data_mode_tradeoffs
+
+	  If you have been historically happy with ext3's performance,
+	  data=ordered mode will be a safe choice and you should
+	  answer 'y' here.  If you understand the reliability and data
+	  privacy issues of data=writeback and are willing to make
+	  that trade off, answer 'n'.
 
 config EXT3_FS_XATTR
 	bool "Ext3 extended attributes"
-- 
GitLab


From 3c4cec65274481ec6332b0a91f19b4c8c5394801 Mon Sep 17 00:00:00 2001
From: Jan Kara <jack@suse.cz>
Date: Mon, 24 Aug 2009 16:38:43 +0200
Subject: [PATCH 1038/1153] ext3: Improve error message that changing
 journaling mode on remount is not possible

This patch makes the error message about changing journaling mode on remount
more descriptive. Some people are going to hit this error now due to commit
bbae8bcc49bc4d002221dab52c79a50a82e7cd1f if they configure a kernel to default
to data=writeback mode. The problem happens if they have data=ordered set for
the root filesystem in /etc/fstab but not in the kernel command line (and they
don't use initrd). Their filesystem then gets mounted as data=writeback by
kernel but then their boot fails because init scripts won't be able to remount
the filesystem rw. Better error message will hopefully make it easier for them
to find the error in their setup and bother us less with error reports :).

Signed-off-by: Jan Kara <jack@suse.cz>
---
 fs/ext3/super.c | 40 +++++++++++++++++++++++++++-------------
 1 file changed, 27 insertions(+), 13 deletions(-)

diff --git a/fs/ext3/super.c b/fs/ext3/super.c
index 524b349c629..a8d80a7f110 100644
--- a/fs/ext3/super.c
+++ b/fs/ext3/super.c
@@ -543,6 +543,19 @@ static inline void ext3_show_quota_options(struct seq_file *seq, struct super_bl
 #endif
 }
 
+static char *data_mode_string(unsigned long mode)
+{
+	switch (mode) {
+	case EXT3_MOUNT_JOURNAL_DATA:
+		return "journal";
+	case EXT3_MOUNT_ORDERED_DATA:
+		return "ordered";
+	case EXT3_MOUNT_WRITEBACK_DATA:
+		return "writeback";
+	}
+	return "unknown";
+}
+
 /*
  * Show an option if
  *  - it's set to a non-default value OR
@@ -616,13 +629,8 @@ static int ext3_show_options(struct seq_file *seq, struct vfsmount *vfs)
 	if (test_opt(sb, NOBH))
 		seq_puts(seq, ",nobh");
 
-	if (test_opt(sb, DATA_FLAGS) == EXT3_MOUNT_JOURNAL_DATA)
-		seq_puts(seq, ",data=journal");
-	else if (test_opt(sb, DATA_FLAGS) == EXT3_MOUNT_ORDERED_DATA)
-		seq_puts(seq, ",data=ordered");
-	else if (test_opt(sb, DATA_FLAGS) == EXT3_MOUNT_WRITEBACK_DATA)
-		seq_puts(seq, ",data=writeback");
-
+	seq_printf(seq, ",data=%s", data_mode_string(sbi->s_mount_opt &
+						     EXT3_MOUNT_DATA_FLAGS));
 	if (test_opt(sb, DATA_ERR_ABORT))
 		seq_puts(seq, ",data_err=abort");
 
@@ -1024,12 +1032,18 @@ static int parse_options (char *options, struct super_block *sb,
 		datacheck:
 			if (is_remount) {
 				if ((sbi->s_mount_opt & EXT3_MOUNT_DATA_FLAGS)
-						!= data_opt) {
-					printk(KERN_ERR
-						"EXT3-fs: cannot change data "
-						"mode on remount\n");
-					return 0;
-				}
+						== data_opt)
+					break;
+				printk(KERN_ERR
+					"EXT3-fs (device %s): Cannot change "
+					"data mode on remount. The filesystem "
+					"is mounted in data=%s mode and you "
+					"try to remount it in data=%s mode.\n",
+					sb->s_id,
+					data_mode_string(sbi->s_mount_opt &
+							EXT3_MOUNT_DATA_FLAGS),
+					data_mode_string(data_opt));
+				return 0;
 			} else {
 				sbi->s_mount_opt &= ~EXT3_MOUNT_DATA_FLAGS;
 				sbi->s_mount_opt |= data_opt;
-- 
GitLab


From 3e475f579e56caf57cadc0cc995c152f9da641a9 Mon Sep 17 00:00:00 2001
From: Martin Michlmayr <tbm@cyrius.com>
Date: Mon, 17 Aug 2009 23:34:10 -1000
Subject: [PATCH 1039/1153] [ARM] Kirkwood: __init requires linux/init.h
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Include linux/init.h for __init to fix this error:

CC [M]  drivers/net/wireless/wl12xx/boot.o
In file included from arch/arm/mach-kirkwood/include/mach/gpio.h:13,
                 from arch/arm/include/asm/gpio.h:5,
                 from include/linux/gpio.h:7,
                 from drivers/net/wireless/wl12xx/boot.c:24:
arch/arm/plat-orion/include/plat/gpio.h:32: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘orion_gpio_init’
make[6]: *** [drivers/net/wireless/wl12xx/boot.o] Error 1
make[5]: *** [drivers/net/wireless/wl12xx] Error 2

Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
---
 arch/arm/plat-orion/include/plat/gpio.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/plat-orion/include/plat/gpio.h b/arch/arm/plat-orion/include/plat/gpio.h
index 9646a94ed3d..07c430fdc9e 100644
--- a/arch/arm/plat-orion/include/plat/gpio.h
+++ b/arch/arm/plat-orion/include/plat/gpio.h
@@ -11,6 +11,8 @@
 #ifndef __PLAT_GPIO_H
 #define __PLAT_GPIO_H
 
+#include <linux/init.h>
+
 /*
  * GENERIC_GPIO primitives.
  */
-- 
GitLab


From c55bf102b675c94edef006ce487d909669221d90 Mon Sep 17 00:00:00 2001
From: John Holland <john.holland@cellent-fs.de>
Date: Wed, 19 Aug 2009 13:24:03 -1000
Subject: [PATCH 1040/1153] [ARM] Kirkwood: enable eSATA on QNAP TS-219P

Initialize PCI/PCIe on the QNAP TS-119, TS-219 and TS-219P hardware
allowing the use of the discrete eSATA controller connected to the PCIe
bus in the TS-219P.

Signed-off-by: John Holland <john.holland@cellent-fs.de>
Tested-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
---
 arch/arm/configs/kirkwood_defconfig  | 2 +-
 arch/arm/mach-kirkwood/ts219-setup.c | 9 +++++++++
 2 files changed, 10 insertions(+), 1 deletion(-)

diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
index 0a1abb978d7..af74cc2de8b 100644
--- a/arch/arm/configs/kirkwood_defconfig
+++ b/arch/arm/configs/kirkwood_defconfig
@@ -629,7 +629,7 @@ CONFIG_SCSI_LOWLEVEL=y
 CONFIG_ATA=y
 # CONFIG_ATA_NONSTANDARD is not set
 CONFIG_SATA_PMP=y
-# CONFIG_SATA_AHCI is not set
+CONFIG_SATA_AHCI=y
 # CONFIG_SATA_SIL24 is not set
 CONFIG_ATA_SFF=y
 # CONFIG_SATA_SVW is not set
diff --git a/arch/arm/mach-kirkwood/ts219-setup.c b/arch/arm/mach-kirkwood/ts219-setup.c
index 01aa213c0a6..ec1a64f263d 100644
--- a/arch/arm/mach-kirkwood/ts219-setup.c
+++ b/arch/arm/mach-kirkwood/ts219-setup.c
@@ -206,6 +206,15 @@ static void __init qnap_ts219_init(void)
 
 }
 
+static int __init ts219_pci_init(void)
+{
+   if (machine_is_ts219())
+           kirkwood_pcie_init();
+
+   return 0;
+}
+subsys_initcall(ts219_pci_init);
+
 MACHINE_START(TS219, "QNAP TS-119/TS-219")
 	/* Maintainer: Martin Michlmayr <tbm@cyrius.com> */
 	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
-- 
GitLab


From 94da210af4978b94cb70318bd1b282a73c50b175 Mon Sep 17 00:00:00 2001
From: Simon Kagstrom <simon.kagstrom@netinsight.net>
Date: Thu, 20 Aug 2009 09:19:53 +0200
Subject: [PATCH 1041/1153] [ARM] Orion NAND: Make asm volatile avoid GCC
 pushing ldrd out of the loop

GCC 4.3.3 and 4.4.1 happily moves the dword load instruction out of the
loop in orion_nand_read_buf. This patch makes the instruction volatile
to avoid the issue. I've discussed this at gcc-help, refer to the thread
at

  http://gcc.gnu.org/ml/gcc-help/2009-08/msg00187.html

The early clobber is added to avoid the destination registers and the
source register overlapping.

Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
---
 drivers/mtd/nand/orion_nand.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
index 7ad972229db..0d9d4bc9c76 100644
--- a/drivers/mtd/nand/orion_nand.c
+++ b/drivers/mtd/nand/orion_nand.c
@@ -61,7 +61,7 @@ static void orion_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
 	buf64 = (uint64_t *)buf;
 	while (i < len/8) {
 		uint64_t x;
-		asm ("ldrd\t%0, [%1]" : "=r" (x) : "r" (io_base));
+		asm volatile ("ldrd\t%0, [%1]" : "=&r" (x) : "r" (io_base));
 		buf64[i++] = x;
 	}
 	i *= 8;
-- 
GitLab


From a6a06f7b577f89d0b916c5ccaff67ca5ed444a78 Mon Sep 17 00:00:00 2001
From: Amerigo Wang <amwang@redhat.com>
Date: Fri, 21 Aug 2009 04:34:45 -0400
Subject: [PATCH 1042/1153] x86: Fix an incorrect argument of reserve_bootmem()

This line looks suspicious, because if this is true, then the
'flags' parameter of function reserve_bootmem_generic() will be
unused when !CONFIG_NUMA. I don't think this is what we want.

Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: akpm@linux-foundation.org
LKML-Reference: <20090821083709.5098.52505.sendpatchset@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/mm/init_64.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/mm/init_64.c b/arch/x86/mm/init_64.c
index 6176fe8f29e..ea56b8cbb6a 100644
--- a/arch/x86/mm/init_64.c
+++ b/arch/x86/mm/init_64.c
@@ -796,7 +796,7 @@ int __init reserve_bootmem_generic(unsigned long phys, unsigned long len,
 		return ret;
 
 #else
-	reserve_bootmem(phys, len, BOOTMEM_DEFAULT);
+	reserve_bootmem(phys, len, flags);
 #endif
 
 	if (phys+len <= MAX_DMA_PFN*PAGE_SIZE) {
-- 
GitLab


From 353d5c30c666580347515da609dd74a2b8e9b828 Mon Sep 17 00:00:00 2001
From: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Date: Mon, 24 Aug 2009 16:30:28 +0100
Subject: [PATCH 1043/1153] mm: fix hugetlb bug due to user_shm_unlock call

2.6.30's commit 8a0bdec194c21c8fdef840989d0d7b742bb5d4bc removed
user_shm_lock() calls in hugetlb_file_setup() but left the
user_shm_unlock call in shm_destroy().

In detail:
Assume that can_do_hugetlb_shm() returns true and hence user_shm_lock()
is not called in hugetlb_file_setup(). However, user_shm_unlock() is
called in any case in shm_destroy() and in the following
atomic_dec_and_lock(&up->__count) in free_uid() is executed and if
up->__count gets zero, also cleanup_user_struct() is scheduled.

Note that sched_destroy_user() is empty if CONFIG_USER_SCHED is not set.
However, the ref counter up->__count gets unexpectedly non-positive and
the corresponding structs are freed even though there are live
references to them, resulting in a kernel oops after a lots of
shmget(SHM_HUGETLB)/shmctl(IPC_RMID) cycles and CONFIG_USER_SCHED set.

Hugh changed Stefan's suggested patch: can_do_hugetlb_shm() at the
time of shm_destroy() may give a different answer from at the time
of hugetlb_file_setup().  And fixed newseg()'s no_id error path,
which has missed user_shm_unlock() ever since it came in 2.6.9.

Reported-by: Stefan Huber <shuber2@gmail.com>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Tested-by: Stefan Huber <shuber2@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/hugetlbfs/inode.c    | 20 ++++++++++++--------
 include/linux/hugetlb.h |  6 ++++--
 ipc/shm.c               |  8 +++++---
 3 files changed, 21 insertions(+), 13 deletions(-)

diff --git a/fs/hugetlbfs/inode.c b/fs/hugetlbfs/inode.c
index 941c8425c10..cb88dac8cca 100644
--- a/fs/hugetlbfs/inode.c
+++ b/fs/hugetlbfs/inode.c
@@ -935,26 +935,28 @@ static int can_do_hugetlb_shm(void)
 	return capable(CAP_IPC_LOCK) || in_group_p(sysctl_hugetlb_shm_group);
 }
 
-struct file *hugetlb_file_setup(const char *name, size_t size, int acctflag)
+struct file *hugetlb_file_setup(const char *name, size_t size, int acctflag,
+						struct user_struct **user)
 {
 	int error = -ENOMEM;
-	int unlock_shm = 0;
 	struct file *file;
 	struct inode *inode;
 	struct dentry *dentry, *root;
 	struct qstr quick_string;
-	struct user_struct *user = current_user();
 
+	*user = NULL;
 	if (!hugetlbfs_vfsmount)
 		return ERR_PTR(-ENOENT);
 
 	if (!can_do_hugetlb_shm()) {
-		if (user_shm_lock(size, user)) {
-			unlock_shm = 1;
+		*user = current_user();
+		if (user_shm_lock(size, *user)) {
 			WARN_ONCE(1,
 			  "Using mlock ulimits for SHM_HUGETLB deprecated\n");
-		} else
+		} else {
+			*user = NULL;
 			return ERR_PTR(-EPERM);
+		}
 	}
 
 	root = hugetlbfs_vfsmount->mnt_root;
@@ -996,8 +998,10 @@ out_inode:
 out_dentry:
 	dput(dentry);
 out_shm_unlock:
-	if (unlock_shm)
-		user_shm_unlock(size, user);
+	if (*user) {
+		user_shm_unlock(size, *user);
+		*user = NULL;
+	}
 	return ERR_PTR(error);
 }
 
diff --git a/include/linux/hugetlb.h b/include/linux/hugetlb.h
index 2723513a565..5cbc620bdfe 100644
--- a/include/linux/hugetlb.h
+++ b/include/linux/hugetlb.h
@@ -10,6 +10,7 @@
 #include <asm/tlbflush.h>
 
 struct ctl_table;
+struct user_struct;
 
 int PageHuge(struct page *page);
 
@@ -146,7 +147,8 @@ static inline struct hugetlbfs_sb_info *HUGETLBFS_SB(struct super_block *sb)
 
 extern const struct file_operations hugetlbfs_file_operations;
 extern struct vm_operations_struct hugetlb_vm_ops;
-struct file *hugetlb_file_setup(const char *name, size_t, int);
+struct file *hugetlb_file_setup(const char *name, size_t size, int acct,
+						struct user_struct **user);
 int hugetlb_get_quota(struct address_space *mapping, long delta);
 void hugetlb_put_quota(struct address_space *mapping, long delta);
 
@@ -168,7 +170,7 @@ static inline void set_file_hugepages(struct file *file)
 
 #define is_file_hugepages(file)			0
 #define set_file_hugepages(file)		BUG()
-#define hugetlb_file_setup(name,size,acctflag)	ERR_PTR(-ENOSYS)
+#define hugetlb_file_setup(name,size,acct,user)	ERR_PTR(-ENOSYS)
 
 #endif /* !CONFIG_HUGETLBFS */
 
diff --git a/ipc/shm.c b/ipc/shm.c
index 15dd238e533..1bc4701ef4f 100644
--- a/ipc/shm.c
+++ b/ipc/shm.c
@@ -174,7 +174,7 @@ static void shm_destroy(struct ipc_namespace *ns, struct shmid_kernel *shp)
 	shm_unlock(shp);
 	if (!is_file_hugepages(shp->shm_file))
 		shmem_lock(shp->shm_file, 0, shp->mlock_user);
-	else
+	else if (shp->mlock_user)
 		user_shm_unlock(shp->shm_file->f_path.dentry->d_inode->i_size,
 						shp->mlock_user);
 	fput (shp->shm_file);
@@ -369,8 +369,8 @@ static int newseg(struct ipc_namespace *ns, struct ipc_params *params)
 		/* hugetlb_file_setup applies strict accounting */
 		if (shmflg & SHM_NORESERVE)
 			acctflag = VM_NORESERVE;
-		file = hugetlb_file_setup(name, size, acctflag);
-		shp->mlock_user = current_user();
+		file = hugetlb_file_setup(name, size, acctflag,
+							&shp->mlock_user);
 	} else {
 		/*
 		 * Do not allow no accounting for OVERCOMMIT_NEVER, even
@@ -410,6 +410,8 @@ static int newseg(struct ipc_namespace *ns, struct ipc_params *params)
 	return error;
 
 no_id:
+	if (shp->mlock_user)	/* shmflg & SHM_HUGETLB case */
+		user_shm_unlock(size, shp->mlock_user);
 	fput(file);
 no_file:
 	security_shm_free(shp);
-- 
GitLab


From 7111dc73923e9737b38a3ef5b5f236109000ff28 Mon Sep 17 00:00:00 2001
From: Trond Myklebust <Trond.Myklebust@netapp.com>
Date: Mon, 24 Aug 2009 19:21:29 -0400
Subject: [PATCH 1044/1153] NFSv4: Fix an infinite looping problem with the
 nfs4_state_manager

Commit 76db6d9500caeaa774a3e32a997eba30bbdc176b (nfs41: add session setup
to the state manager) introduces an infinite loop possibility in the NFSv4
state manager. By first checking nfs4_has_session() before clearing the
NFS4CLNT_SESSION_SETUP flag, it allows for a situation where someone sets
that flag, but it never gets cleared, and so the state manager loops.

In fact commit c3fad1b1aaf850bf692642642ace7cd0d64af0a3 (nfs41: add session
reset to state manager) causes this to happen every time we get a network
partition error.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/nfs/nfs4state.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/fs/nfs/nfs4state.c b/fs/nfs/nfs4state.c
index 65ca8c18476..1434080aefe 100644
--- a/fs/nfs/nfs4state.c
+++ b/fs/nfs/nfs4state.c
@@ -1250,8 +1250,8 @@ static void nfs4_state_manager(struct nfs_client *clp)
 				continue;
 		}
 		/* Initialize or reset the session */
-		if (nfs4_has_session(clp) &&
-		   test_and_clear_bit(NFS4CLNT_SESSION_SETUP, &clp->cl_state)) {
+		if (test_and_clear_bit(NFS4CLNT_SESSION_SETUP, &clp->cl_state)
+		   && nfs4_has_session(clp)) {
 			if (clp->cl_cons_state == NFS_CS_SESSION_INITING)
 				status = nfs4_initialize_session(clp);
 			else
-- 
GitLab


From 942642a412454c3365f0abc8399c8ef2944f4eac Mon Sep 17 00:00:00 2001
From: Sean Young <sean@mess.org>
Date: Thu, 6 Aug 2009 17:35:50 +0800
Subject: [PATCH 1045/1153] drm/i915: Set the multiplier for SDVO on G33
 platform

http://bugs.freedesktop.org/show_bug.cgi?id=21417

Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_display.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index d6fce213341..f611e216b0b 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -2396,7 +2396,7 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 		if (is_sdvo) {
 			dpll |= DPLL_DVO_HIGH_SPEED;
 			sdvo_pixel_multiply = adjusted_mode->clock / mode->clock;
-			if (IS_I945G(dev) || IS_I945GM(dev))
+			if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
 				dpll |= (sdvo_pixel_multiply - 1) << SDVO_MULTIPLIER_SHIFT_HIRES;
 			else if (IS_IGDNG(dev))
 				dpll |= (sdvo_pixel_multiply - 1) << PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT;
-- 
GitLab


From bc5e5718acd7f7d000d913e619562767863610bf Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Bruno=20Pr=C3=A9mont?= <bonbons@linux-vserver.org>
Date: Sat, 8 Aug 2009 13:01:17 +0200
Subject: [PATCH 1046/1153] drm/i915: Check if BIOS enabled dual-channel LVDS
 on 8xx, not only on 9xx
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Commit 0c2e39525b3b53a97a0202c5f35058147e53977e is not sufficient to
get fd.o bug #20115 fixed.
In addition intel_find_best_PLL() must not only rely on BIOS settings
for i9xx chips but also for i8xx, so drop the IS_I9XX() check.

Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_display.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index f611e216b0b..8fd90f31b60 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -666,7 +666,7 @@ intel_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
 	intel_clock_t clock;
 	int err = target;
 
-	if (IS_I9XX(dev) && intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) &&
+	if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS) &&
 	    (I915_READ(LVDS)) != 0) {
 		/*
 		 * For LVDS, if the panel is on, just rely on its current
-- 
GitLab


From 19e1f888c681d9f71ae0a814902d334eac1911dd Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Sun, 9 Aug 2009 13:50:53 +0200
Subject: [PATCH 1047/1153] drm/i915: Fix typo that broke SVID1 in
 intel_sdvo_multifunc_encoder()

Bit SDVO_OUTPUT_SVID0 was tested twice

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_sdvo.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c
index 5371d933255..95ca0acc494 100644
--- a/drivers/gpu/drm/i915/intel_sdvo.c
+++ b/drivers/gpu/drm/i915/intel_sdvo.c
@@ -1458,7 +1458,7 @@ intel_sdvo_multifunc_encoder(struct intel_output *intel_output)
 		(SDVO_OUTPUT_RGB0 | SDVO_OUTPUT_RGB1))
 		caps++;
 	if (sdvo_priv->caps.output_flags &
-		(SDVO_OUTPUT_SVID0 | SDVO_OUTPUT_SVID0))
+		(SDVO_OUTPUT_SVID0 | SDVO_OUTPUT_SVID1))
 		caps++;
 	if (sdvo_priv->caps.output_flags &
 		(SDVO_OUTPUT_CVBS0 | SDVO_OUTPUT_CVBS1))
-- 
GitLab


From 27185ae1b795a4ba5e25b95fb5584e950545d774 Mon Sep 17 00:00:00 2001
From: Ma Ling <ling.ma@intel.com>
Date: Mon, 24 Aug 2009 13:50:23 +0800
Subject: [PATCH 1048/1153] drm/i915: Always use SDVO_B detect bit for SDVO
 output detection.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

After the following commit is shipped, the SDVO C detection will depend on
the SDVO_C/DP detion bit.
commit 13520b051e8888dd3af9bda639d83e7df76613d1
Author: Kristian Høgsberg <krh@redhat.com>
Date:   Fri Mar 13 15:42:14 2009 -0400

    drm/i915: Read the right SDVO register when detecting SVDO/HDMI.

According to the spec we should continue to detect the SDVO_B/C based on
the SDVO_B detection bit.  The new detection bit on G4X platform is for
the HDMI_C detection rather than SDVO_C detection.

https://bugs.freedesktop.org/show_bug.cgi?id=20639

Signed-off-by: Ma Ling <ling.ma@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_display.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 8fd90f31b60..4fad113a1b2 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -3218,30 +3218,30 @@ static void intel_setup_outputs(struct drm_device *dev)
 			intel_dp_init(dev, PCH_DP_D);
 
 	} else if (IS_I9XX(dev)) {
-		int found;
-		u32 reg;
+		bool found = false;
 
 		if (I915_READ(SDVOB) & SDVO_DETECTED) {
 			found = intel_sdvo_init(dev, SDVOB);
 			if (!found && SUPPORTS_INTEGRATED_HDMI(dev))
 				intel_hdmi_init(dev, SDVOB);
+
 			if (!found && SUPPORTS_INTEGRATED_DP(dev))
 				intel_dp_init(dev, DP_B);
 		}
 
 		/* Before G4X SDVOC doesn't have its own detect register */
-		if (IS_G4X(dev))
-			reg = SDVOC;
-		else
-			reg = SDVOB;
 
-		if (I915_READ(reg) & SDVO_DETECTED) {
+		if (I915_READ(SDVOB) & SDVO_DETECTED)
 			found = intel_sdvo_init(dev, SDVOC);
-			if (!found && SUPPORTS_INTEGRATED_HDMI(dev))
+
+		if (!found && (I915_READ(SDVOC) & SDVO_DETECTED)) {
+
+			if (SUPPORTS_INTEGRATED_HDMI(dev))
 				intel_hdmi_init(dev, SDVOC);
-			if (!found && SUPPORTS_INTEGRATED_DP(dev))
+			if (SUPPORTS_INTEGRATED_DP(dev))
 				intel_dp_init(dev, DP_C);
 		}
+
 		if (SUPPORTS_INTEGRATED_DP(dev) && (I915_READ(DP_D) & DP_DETECTED))
 			intel_dp_init(dev, DP_D);
 	} else
-- 
GitLab


From f8aed700c6ec46ddade6570004ce25332283b306 Mon Sep 17 00:00:00 2001
From: Ma Ling <ling.ma@intel.com>
Date: Mon, 24 Aug 2009 13:50:24 +0800
Subject: [PATCH 1049/1153] drm/i915: Set crtc/clone mask in different output
 devices

Based on Bspec each encoder has different sharing pipe property,
i.e. Integrated or SDVO TV both will occupy one pipe exclusively,
and sdvo-non-tv and crt are allowed to share one. The patch moves
sharing judgment into differnet output functions, and sets the right
clone bit.

This fixes both HDMI outputs choosing the same pipe.

https://bugs.freedesktop.org/show_bug.cgi?id=22247

Signed-off-by: Ma Ling <ling.ma@intel.com>
Reviewed-by : Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
---
 drivers/gpu/drm/i915/intel_crt.c     |  4 +++
 drivers/gpu/drm/i915/intel_display.c | 49 +++-------------------------
 drivers/gpu/drm/i915/intel_dp.c      | 12 +++++++
 drivers/gpu/drm/i915/intel_drv.h     | 20 ++++++++++++
 drivers/gpu/drm/i915/intel_dvo.c     |  6 ++++
 drivers/gpu/drm/i915/intel_hdmi.c    | 18 ++++++----
 drivers/gpu/drm/i915/intel_lvds.c    |  2 ++
 drivers/gpu/drm/i915/intel_sdvo.c    | 11 +++++++
 drivers/gpu/drm/i915/intel_tv.c      |  2 ++
 9 files changed, 73 insertions(+), 51 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_crt.c b/drivers/gpu/drm/i915/intel_crt.c
index 4cf8e2e88a4..d1294978a38 100644
--- a/drivers/gpu/drm/i915/intel_crt.c
+++ b/drivers/gpu/drm/i915/intel_crt.c
@@ -537,6 +537,10 @@ void intel_crt_init(struct drm_device *dev)
 	}
 
 	intel_output->type = INTEL_OUTPUT_ANALOG;
+	intel_output->clone_mask = (1 << INTEL_SDVO_NON_TV_CLONE_BIT) |
+				   (1 << INTEL_ANALOG_CLONE_BIT) |
+				   (1 << INTEL_SDVO_LVDS_CLONE_BIT);
+	intel_output->crtc_mask = (1 << 0) | (1 << 1);
 	connector->interlace_allowed = 0;
 	connector->doublescan_allowed = 0;
 
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 4fad113a1b2..3fadb535885 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -3170,7 +3170,7 @@ static int intel_connector_clones(struct drm_device *dev, int type_mask)
 
         list_for_each_entry(connector, &dev->mode_config.connector_list, head) {
 		struct intel_output *intel_output = to_intel_output(connector);
-		if (type_mask & (1 << intel_output->type))
+		if (type_mask & intel_output->clone_mask)
 			index_mask |= (1 << entry);
 		entry++;
 	}
@@ -3253,51 +3253,10 @@ static void intel_setup_outputs(struct drm_device *dev)
 	list_for_each_entry(connector, &dev->mode_config.connector_list, head) {
 		struct intel_output *intel_output = to_intel_output(connector);
 		struct drm_encoder *encoder = &intel_output->enc;
-		int crtc_mask = 0, clone_mask = 0;
 
-		/* valid crtcs */
-		switch(intel_output->type) {
-		case INTEL_OUTPUT_HDMI:
-			crtc_mask = ((1 << 0)|
-				     (1 << 1));
-			clone_mask = ((1 << INTEL_OUTPUT_HDMI));
-			break;
-		case INTEL_OUTPUT_DVO:
-		case INTEL_OUTPUT_SDVO:
-			crtc_mask = ((1 << 0)|
-				     (1 << 1));
-			clone_mask = ((1 << INTEL_OUTPUT_ANALOG) |
-				      (1 << INTEL_OUTPUT_DVO) |
-				      (1 << INTEL_OUTPUT_SDVO));
-			break;
-		case INTEL_OUTPUT_ANALOG:
-			crtc_mask = ((1 << 0)|
-				     (1 << 1));
-			clone_mask = ((1 << INTEL_OUTPUT_ANALOG) |
-				      (1 << INTEL_OUTPUT_DVO) |
-				      (1 << INTEL_OUTPUT_SDVO));
-			break;
-		case INTEL_OUTPUT_LVDS:
-			crtc_mask = (1 << 1);
-			clone_mask = (1 << INTEL_OUTPUT_LVDS);
-			break;
-		case INTEL_OUTPUT_TVOUT:
-			crtc_mask = ((1 << 0) |
-				     (1 << 1));
-			clone_mask = (1 << INTEL_OUTPUT_TVOUT);
-			break;
-		case INTEL_OUTPUT_DISPLAYPORT:
-			crtc_mask = ((1 << 0) |
-				     (1 << 1));
-			clone_mask = (1 << INTEL_OUTPUT_DISPLAYPORT);
-			break;
-		case INTEL_OUTPUT_EDP:
-			crtc_mask = (1 << 1);
-			clone_mask = (1 << INTEL_OUTPUT_EDP);
-			break;
-		}
-		encoder->possible_crtcs = crtc_mask;
-		encoder->possible_clones = intel_connector_clones(dev, clone_mask);
+		encoder->possible_crtcs = intel_output->crtc_mask;
+		encoder->possible_clones = intel_connector_clones(dev,
+						intel_output->clone_mask);
 	}
 }
 
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index a6ff15ac548..f2afc4af4bc 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -1254,6 +1254,18 @@ intel_dp_init(struct drm_device *dev, int output_reg)
 	else
 		intel_output->type = INTEL_OUTPUT_DISPLAYPORT;
 
+	if (output_reg == DP_B)
+		intel_output->clone_mask = (1 << INTEL_DP_B_CLONE_BIT);
+	else if (output_reg == DP_C)
+		intel_output->clone_mask = (1 << INTEL_DP_C_CLONE_BIT);
+	else if (output_reg == DP_D)
+		intel_output->clone_mask = (1 << INTEL_DP_D_CLONE_BIT);
+
+	if (IS_eDP(intel_output)) {
+		intel_output->crtc_mask = (1 << 1);
+		intel_output->clone_mask = (1 << INTEL_OUTPUT_EDP);
+	} else
+		intel_output->crtc_mask = (1 << 0) | (1 << 1);
 	connector->interlace_allowed = true;
 	connector->doublescan_allowed = 0;
 
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index d6f92ea1b55..25aa6facc12 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -57,6 +57,24 @@
 #define INTEL_OUTPUT_DISPLAYPORT 7
 #define INTEL_OUTPUT_EDP 8
 
+/* Intel Pipe Clone Bit */
+#define INTEL_HDMIB_CLONE_BIT 1
+#define INTEL_HDMIC_CLONE_BIT 2
+#define INTEL_HDMID_CLONE_BIT 3
+#define INTEL_HDMIE_CLONE_BIT 4
+#define INTEL_HDMIF_CLONE_BIT 5
+#define INTEL_SDVO_NON_TV_CLONE_BIT 6
+#define INTEL_SDVO_TV_CLONE_BIT 7
+#define INTEL_SDVO_LVDS_CLONE_BIT 8
+#define INTEL_ANALOG_CLONE_BIT 9
+#define INTEL_TV_CLONE_BIT 10
+#define INTEL_DP_B_CLONE_BIT 11
+#define INTEL_DP_C_CLONE_BIT 12
+#define INTEL_DP_D_CLONE_BIT 13
+#define INTEL_LVDS_CLONE_BIT 14
+#define INTEL_DVO_TMDS_CLONE_BIT 15
+#define INTEL_DVO_LVDS_CLONE_BIT 16
+
 #define INTEL_DVO_CHIP_NONE 0
 #define INTEL_DVO_CHIP_LVDS 1
 #define INTEL_DVO_CHIP_TMDS 2
@@ -86,6 +104,8 @@ struct intel_output {
 	bool needs_tv_clock;
 	void *dev_priv;
 	void (*hot_plug)(struct intel_output *);
+	int crtc_mask;
+	int clone_mask;
 };
 
 struct intel_crtc {
diff --git a/drivers/gpu/drm/i915/intel_dvo.c b/drivers/gpu/drm/i915/intel_dvo.c
index 13bff20930e..a4d2606de77 100644
--- a/drivers/gpu/drm/i915/intel_dvo.c
+++ b/drivers/gpu/drm/i915/intel_dvo.c
@@ -435,14 +435,20 @@ void intel_dvo_init(struct drm_device *dev)
 			continue;
 
 		intel_output->type = INTEL_OUTPUT_DVO;
+		intel_output->crtc_mask = (1 << 0) | (1 << 1);
 		switch (dvo->type) {
 		case INTEL_DVO_CHIP_TMDS:
+			intel_output->clone_mask =
+				(1 << INTEL_DVO_TMDS_CLONE_BIT) |
+				(1 << INTEL_ANALOG_CLONE_BIT);
 			drm_connector_init(dev, connector,
 					   &intel_dvo_connector_funcs,
 					   DRM_MODE_CONNECTOR_DVII);
 			encoder_type = DRM_MODE_ENCODER_TMDS;
 			break;
 		case INTEL_DVO_CHIP_LVDS:
+			intel_output->clone_mask =
+				(1 << INTEL_DVO_LVDS_CLONE_BIT);
 			drm_connector_init(dev, connector,
 					   &intel_dvo_connector_funcs,
 					   DRM_MODE_CONNECTOR_LVDS);
diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
index 1842290cded..fa304e13601 100644
--- a/drivers/gpu/drm/i915/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/intel_hdmi.c
@@ -230,22 +230,28 @@ void intel_hdmi_init(struct drm_device *dev, int sdvox_reg)
 
 	connector->interlace_allowed = 0;
 	connector->doublescan_allowed = 0;
+	intel_output->crtc_mask = (1 << 0) | (1 << 1);
 
 	/* Set up the DDC bus. */
-	if (sdvox_reg == SDVOB)
+	if (sdvox_reg == SDVOB) {
+		intel_output->clone_mask = (1 << INTEL_HDMIB_CLONE_BIT);
 		intel_output->ddc_bus = intel_i2c_create(dev, GPIOE, "HDMIB");
-	else if (sdvox_reg == SDVOC)
+	} else if (sdvox_reg == SDVOC) {
+		intel_output->clone_mask = (1 << INTEL_HDMIC_CLONE_BIT);
 		intel_output->ddc_bus = intel_i2c_create(dev, GPIOD, "HDMIC");
-	else if (sdvox_reg == HDMIB)
+	} else if (sdvox_reg == HDMIB) {
+		intel_output->clone_mask = (1 << INTEL_HDMID_CLONE_BIT);
 		intel_output->ddc_bus = intel_i2c_create(dev, PCH_GPIOE,
 								"HDMIB");
-	else if (sdvox_reg == HDMIC)
+	} else if (sdvox_reg == HDMIC) {
+		intel_output->clone_mask = (1 << INTEL_HDMIE_CLONE_BIT);
 		intel_output->ddc_bus = intel_i2c_create(dev, PCH_GPIOD,
 								"HDMIC");
-	else if (sdvox_reg == HDMID)
+	} else if (sdvox_reg == HDMID) {
+		intel_output->clone_mask = (1 << INTEL_HDMIF_CLONE_BIT);
 		intel_output->ddc_bus = intel_i2c_create(dev, PCH_GPIOF,
 								"HDMID");
-
+	}
 	if (!intel_output->ddc_bus)
 		goto err_connector;
 
diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c
index 3f445a80c55..8df02ef8926 100644
--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -916,6 +916,8 @@ void intel_lvds_init(struct drm_device *dev)
 	drm_mode_connector_attach_encoder(&intel_output->base, &intel_output->enc);
 	intel_output->type = INTEL_OUTPUT_LVDS;
 
+	intel_output->clone_mask = (1 << INTEL_LVDS_CLONE_BIT);
+	intel_output->crtc_mask = (1 << 1);
 	drm_encoder_helper_add(encoder, &intel_lvds_helper_funcs);
 	drm_connector_helper_add(connector, &intel_lvds_connector_helper_funcs);
 	connector->display_info.subpixel_order = SubPixelHorizontalRGB;
diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c
index 95ca0acc494..d3b74ba62b4 100644
--- a/drivers/gpu/drm/i915/intel_sdvo.c
+++ b/drivers/gpu/drm/i915/intel_sdvo.c
@@ -1967,6 +1967,9 @@ intel_sdvo_output_setup(struct intel_output *intel_output, uint16_t flags)
 			intel_sdvo_set_colorimetry(intel_output,
 						   SDVO_COLORIMETRY_RGB256);
 			connector->connector_type = DRM_MODE_CONNECTOR_HDMIA;
+			intel_output->clone_mask =
+					(1 << INTEL_SDVO_NON_TV_CLONE_BIT) |
+					(1 << INTEL_ANALOG_CLONE_BIT);
 		}
 	} else if (flags & SDVO_OUTPUT_SVID0) {
 
@@ -1975,11 +1978,14 @@ intel_sdvo_output_setup(struct intel_output *intel_output, uint16_t flags)
 		connector->connector_type = DRM_MODE_CONNECTOR_SVIDEO;
 		sdvo_priv->is_tv = true;
 		intel_output->needs_tv_clock = true;
+		intel_output->clone_mask = 1 << INTEL_SDVO_TV_CLONE_BIT;
 	} else if (flags & SDVO_OUTPUT_RGB0) {
 
 		sdvo_priv->controlled_output = SDVO_OUTPUT_RGB0;
 		encoder->encoder_type = DRM_MODE_ENCODER_DAC;
 		connector->connector_type = DRM_MODE_CONNECTOR_VGA;
+		intel_output->clone_mask = (1 << INTEL_SDVO_NON_TV_CLONE_BIT) |
+					(1 << INTEL_ANALOG_CLONE_BIT);
 	} else if (flags & SDVO_OUTPUT_RGB1) {
 
 		sdvo_priv->controlled_output = SDVO_OUTPUT_RGB1;
@@ -1991,12 +1997,16 @@ intel_sdvo_output_setup(struct intel_output *intel_output, uint16_t flags)
 		encoder->encoder_type = DRM_MODE_ENCODER_LVDS;
 		connector->connector_type = DRM_MODE_CONNECTOR_LVDS;
 		sdvo_priv->is_lvds = true;
+		intel_output->clone_mask = (1 << INTEL_ANALOG_CLONE_BIT) |
+					(1 << INTEL_SDVO_LVDS_CLONE_BIT);
 	} else if (flags & SDVO_OUTPUT_LVDS1) {
 
 		sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS1;
 		encoder->encoder_type = DRM_MODE_ENCODER_LVDS;
 		connector->connector_type = DRM_MODE_CONNECTOR_LVDS;
 		sdvo_priv->is_lvds = true;
+		intel_output->clone_mask = (1 << INTEL_ANALOG_CLONE_BIT) |
+					(1 << INTEL_SDVO_LVDS_CLONE_BIT);
 	} else {
 
 		unsigned char bytes[2];
@@ -2009,6 +2019,7 @@ intel_sdvo_output_setup(struct intel_output *intel_output, uint16_t flags)
 				  bytes[0], bytes[1]);
 		ret = false;
 	}
+	intel_output->crtc_mask = (1 << 0) | (1 << 1);
 
 	if (ret && registered)
 		ret = drm_sysfs_connector_add(connector) == 0 ? true : false;
diff --git a/drivers/gpu/drm/i915/intel_tv.c b/drivers/gpu/drm/i915/intel_tv.c
index da4ab4dc163..2fbe13a0de8 100644
--- a/drivers/gpu/drm/i915/intel_tv.c
+++ b/drivers/gpu/drm/i915/intel_tv.c
@@ -1718,6 +1718,7 @@ intel_tv_init(struct drm_device *dev)
 	if (!intel_output) {
 		return;
 	}
+
 	connector = &intel_output->base;
 
 	drm_connector_init(dev, connector, &intel_tv_connector_funcs,
@@ -1729,6 +1730,7 @@ intel_tv_init(struct drm_device *dev)
 	drm_mode_connector_attach_encoder(&intel_output->base, &intel_output->enc);
 	tv_priv = (struct intel_tv_priv *)(intel_output + 1);
 	intel_output->type = INTEL_OUTPUT_TVOUT;
+	intel_output->clone_mask = (1 << INTEL_TV_CLONE_BIT);
 	intel_output->enc.possible_crtcs = ((1 << 0) | (1 << 1));
 	intel_output->enc.possible_clones = (1 << INTEL_OUTPUT_TVOUT);
 	intel_output->dev_priv = tv_priv;
-- 
GitLab


From a2cb6a4dd470d7a64255a10b843b0d188416b78f Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Mon, 24 Aug 2009 19:37:05 -0700
Subject: [PATCH 1050/1153] pkt_sched: Fix bogon in tasklet_hrtimer changes.

Reported by Stephen Rothwell, luckily it's harmless:

net/sched/sch_api.c: In function 'qdisc_watchdog':
net/sched/sch_api.c:460: warning: initialization from incompatible pointer type
net/sched/sch_cbq.c: In function 'cbq_undelay':
net/sched/sch_cbq.c:595: warning: initialization from incompatible pointer type

Signed-off-by: David S. Miller <davem@davemloft.net>
---
 net/sched/sch_api.c | 2 +-
 net/sched/sch_cbq.c | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/net/sched/sch_api.c b/net/sched/sch_api.c
index e1c2bf7e9ba..92e6f3a52c1 100644
--- a/net/sched/sch_api.c
+++ b/net/sched/sch_api.c
@@ -458,7 +458,7 @@ EXPORT_SYMBOL(qdisc_warn_nonwc);
 static enum hrtimer_restart qdisc_watchdog(struct hrtimer *timer)
 {
 	struct qdisc_watchdog *wd = container_of(timer, struct qdisc_watchdog,
-						 timer);
+						 timer.timer);
 
 	wd->qdisc->flags &= ~TCQ_F_THROTTLED;
 	__netif_schedule(qdisc_root(wd->qdisc));
diff --git a/net/sched/sch_cbq.c b/net/sched/sch_cbq.c
index 81652d6ccd3..149b0405c5e 100644
--- a/net/sched/sch_cbq.c
+++ b/net/sched/sch_cbq.c
@@ -593,7 +593,7 @@ static psched_tdiff_t cbq_undelay_prio(struct cbq_sched_data *q, int prio,
 static enum hrtimer_restart cbq_undelay(struct hrtimer *timer)
 {
 	struct cbq_sched_data *q = container_of(timer, struct cbq_sched_data,
-						delay_timer);
+						delay_timer.timer);
 	struct Qdisc *sch = q->watchdog.qdisc;
 	psched_time_t now;
 	psched_tdiff_t delay = 0;
-- 
GitLab


From b1ddaf681e362ed453182ddee1699d7487069a16 Mon Sep 17 00:00:00 2001
From: Clemens Ladisch <clemens@ladisch.de>
Date: Tue, 25 Aug 2009 08:15:41 +0200
Subject: [PATCH 1051/1153] sound: pcm_lib: fix unsorted list constraint
 handling

snd_interval_list() expected a sorted list but did not document this, so
there are drivers that give it an unsorted list.  To fix this, change
the algorithm to work with any list.

This fixes the "Slave PCM not usable" error with USB devices that have
multiple alternate settings with sample rates in decreasing order, such
as the Philips Askey VC010 WebCam.

http://bugzilla.kernel.org/show_bug.cgi?id=14028

Reported-and-tested-by: Andrzej <adkadk@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/core/pcm_lib.c | 39 ++++++++-------------------------------
 1 file changed, 8 insertions(+), 31 deletions(-)

diff --git a/sound/core/pcm_lib.c b/sound/core/pcm_lib.c
index 333e4dd2945..d8a7bb28cd8 100644
--- a/sound/core/pcm_lib.c
+++ b/sound/core/pcm_lib.c
@@ -909,47 +909,24 @@ static int snd_interval_ratden(struct snd_interval *i,
 int snd_interval_list(struct snd_interval *i, unsigned int count, unsigned int *list, unsigned int mask)
 {
         unsigned int k;
-	int changed = 0;
+	struct snd_interval list_range;
 
 	if (!count) {
 		i->empty = 1;
 		return -EINVAL;
 	}
+	snd_interval_any(&list_range);
+	list_range.min = UINT_MAX;
+	list_range.max = 0;
         for (k = 0; k < count; k++) {
 		if (mask && !(mask & (1 << k)))
 			continue;
-                if (i->min == list[k] && !i->openmin)
-                        goto _l1;
-                if (i->min < list[k]) {
-                        i->min = list[k];
-			i->openmin = 0;
-			changed = 1;
-                        goto _l1;
-                }
-        }
-        i->empty = 1;
-        return -EINVAL;
- _l1:
-        for (k = count; k-- > 0;) {
-		if (mask && !(mask & (1 << k)))
+		if (!snd_interval_test(i, list[k]))
 			continue;
-                if (i->max == list[k] && !i->openmax)
-                        goto _l2;
-                if (i->max > list[k]) {
-                        i->max = list[k];
-			i->openmax = 0;
-			changed = 1;
-                        goto _l2;
-                }
+		list_range.min = min(list_range.min, list[k]);
+		list_range.max = max(list_range.max, list[k]);
         }
-        i->empty = 1;
-        return -EINVAL;
- _l2:
-	if (snd_interval_checkempty(i)) {
-		i->empty = 1;
-		return -EINVAL;
-	}
-        return changed;
+	return snd_interval_refine(i, &list_range);
 }
 
 EXPORT_SYMBOL(snd_interval_list);
-- 
GitLab


From c62e43202e7cf50ca24bce58b255df7bf5de69d0 Mon Sep 17 00:00:00 2001
From: Jan Beulich <JBeulich@novell.com>
Date: Tue, 25 Aug 2009 14:50:53 +0100
Subject: [PATCH 1052/1153] x86: Fix build with older binutils and consolidate
 linker script

binutils prior to 2.17 can't deal with the currently possible
situation of a new segment following the per-CPU segment, but
that new segment being empty - objcopy misplaces the .bss (and
perhaps also the .brk) sections outside of any segment.

However, the current ordering of sections really just appears
to be the effect of cumulative unrelated changes; re-ordering
things allows to easily guarantee that the segment following
the per-CPU one is non-empty, and at once eliminates the need
for the bogus data.init2 segment.

Once touching this code, also use the various data section
helper macros from include/asm-generic/vmlinux.lds.h.

-v2: fix !SMP builds.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: <sam@ravnborg.org>
LKML-Reference: <4A94085D02000078000119A5@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/vmlinux.lds.S | 126 +++++++++++++---------------------
 1 file changed, 47 insertions(+), 79 deletions(-)

diff --git a/arch/x86/kernel/vmlinux.lds.S b/arch/x86/kernel/vmlinux.lds.S
index 78d185d797d..9fc178255c0 100644
--- a/arch/x86/kernel/vmlinux.lds.S
+++ b/arch/x86/kernel/vmlinux.lds.S
@@ -46,11 +46,10 @@ PHDRS {
 	data PT_LOAD FLAGS(7);          /* RWE */
 #ifdef CONFIG_X86_64
 	user PT_LOAD FLAGS(7);          /* RWE */
-	data.init PT_LOAD FLAGS(7);     /* RWE */
 #ifdef CONFIG_SMP
 	percpu PT_LOAD FLAGS(7);        /* RWE */
 #endif
-	data.init2 PT_LOAD FLAGS(7);    /* RWE */
+	init PT_LOAD FLAGS(7);          /* RWE */
 #endif
 	note PT_NOTE FLAGS(0);          /* ___ */
 }
@@ -103,65 +102,43 @@ SECTIONS
 		__stop___ex_table = .;
 	} :text = 0x9090
 
-	RODATA
+	RO_DATA(PAGE_SIZE)
 
 	/* Data */
-	. = ALIGN(PAGE_SIZE);
 	.data : AT(ADDR(.data) - LOAD_OFFSET) {
 		/* Start of data section */
 		_sdata = .;
-		DATA_DATA
-		CONSTRUCTORS
-	} :data
+
+		/* init_task */
+		INIT_TASK_DATA(THREAD_SIZE)
 
 #ifdef CONFIG_X86_32
-	/* 32 bit has nosave before _edata */
-	. = ALIGN(PAGE_SIZE);
-	.data_nosave : AT(ADDR(.data_nosave) - LOAD_OFFSET) {
-		__nosave_begin = .;
-		*(.data.nosave)
-		. = ALIGN(PAGE_SIZE);
-		__nosave_end = .;
-	}
+		/* 32 bit has nosave before _edata */
+		NOSAVE_DATA
 #endif
 
-	. = ALIGN(PAGE_SIZE);
-	.data.page_aligned : AT(ADDR(.data.page_aligned) - LOAD_OFFSET) {
-		*(.data.page_aligned)
+		PAGE_ALIGNED_DATA(PAGE_SIZE)
 		*(.data.idt)
-	}
 
-#ifdef CONFIG_X86_32
-	. = ALIGN(32);
-#else
-	. = ALIGN(PAGE_SIZE);
-	. = ALIGN(CONFIG_X86_L1_CACHE_BYTES);
-#endif
-	.data.cacheline_aligned :
-		AT(ADDR(.data.cacheline_aligned) - LOAD_OFFSET) {
-		*(.data.cacheline_aligned)
-	}
+		CACHELINE_ALIGNED_DATA(CONFIG_X86_L1_CACHE_BYTES)
 
-	/* rarely changed data like cpu maps */
-#ifdef CONFIG_X86_32
-	. = ALIGN(32);
-#else
-	. = ALIGN(CONFIG_X86_INTERNODE_CACHE_BYTES);
-#endif
-	.data.read_mostly : AT(ADDR(.data.read_mostly) - LOAD_OFFSET) {
-		*(.data.read_mostly)
+		DATA_DATA
+		CONSTRUCTORS
+
+		/* rarely changed data like cpu maps */
+		READ_MOSTLY_DATA(CONFIG_X86_INTERNODE_CACHE_BYTES)
 
 		/* End of data section */
 		_edata = .;
-	}
+	} :data
 
 #ifdef CONFIG_X86_64
 
 #define VSYSCALL_ADDR (-10*1024*1024)
-#define VSYSCALL_PHYS_ADDR ((LOADADDR(.data.read_mostly) + \
-                            SIZEOF(.data.read_mostly) + 4095) & ~(4095))
-#define VSYSCALL_VIRT_ADDR ((ADDR(.data.read_mostly) + \
-                            SIZEOF(.data.read_mostly) + 4095) & ~(4095))
+#define VSYSCALL_PHYS_ADDR ((LOADADDR(.data) + SIZEOF(.data) + \
+                            PAGE_SIZE - 1) & ~(PAGE_SIZE - 1))
+#define VSYSCALL_VIRT_ADDR ((ADDR(.data) + SIZEOF(.data) + \
+                            PAGE_SIZE - 1) & ~(PAGE_SIZE - 1))
 
 #define VLOAD_OFFSET (VSYSCALL_ADDR - VSYSCALL_PHYS_ADDR)
 #define VLOAD(x) (ADDR(x) - VLOAD_OFFSET)
@@ -227,35 +204,29 @@ SECTIONS
 
 #endif /* CONFIG_X86_64 */
 
-	/* init_task */
-	. = ALIGN(THREAD_SIZE);
-	.data.init_task : AT(ADDR(.data.init_task) - LOAD_OFFSET) {
-		*(.data.init_task)
+	/* Init code and data - will be freed after init */
+	. = ALIGN(PAGE_SIZE);
+	.init.begin : AT(ADDR(.init.begin) - LOAD_OFFSET) {
+		__init_begin = .; /* paired with __init_end */
 	}
-#ifdef CONFIG_X86_64
-	 :data.init
-#endif
 
+#if defined(CONFIG_X86_64) && defined(CONFIG_SMP)
 	/*
-	 * smp_locks might be freed after init
-	 * start/end must be page aligned
+	 * percpu offsets are zero-based on SMP.  PERCPU_VADDR() changes the
+	 * output PHDR, so the next output section - .init.text - should
+	 * start another segment - init.
 	 */
-	. = ALIGN(PAGE_SIZE);
-	.smp_locks : AT(ADDR(.smp_locks) - LOAD_OFFSET) {
-		__smp_locks = .;
-		*(.smp_locks)
-		__smp_locks_end = .;
-		. = ALIGN(PAGE_SIZE);
-	}
+	PERCPU_VADDR(0, :percpu)
+#endif
 
-	/* Init code and data - will be freed after init */
-	. = ALIGN(PAGE_SIZE);
 	.init.text : AT(ADDR(.init.text) - LOAD_OFFSET) {
-		__init_begin = .; /* paired with __init_end */
 		_sinittext = .;
 		INIT_TEXT
 		_einittext = .;
 	}
+#ifdef CONFIG_X86_64
+	:init
+#endif
 
 	.init.data : AT(ADDR(.init.data) - LOAD_OFFSET) {
 		INIT_DATA
@@ -326,17 +297,7 @@ SECTIONS
 	}
 #endif
 
-#if defined(CONFIG_X86_64) && defined(CONFIG_SMP)
-	/*
-	 * percpu offsets are zero-based on SMP.  PERCPU_VADDR() changes the
-	 * output PHDR, so the next output section - __data_nosave - should
-	 * start another section data.init2.  Also, pda should be at the head of
-	 * percpu area.  Preallocate it and define the percpu offset symbol
-	 * so that it can be accessed as a percpu variable.
-	 */
-	. = ALIGN(PAGE_SIZE);
-	PERCPU_VADDR(0, :percpu)
-#else
+#if !defined(CONFIG_X86_64) || !defined(CONFIG_SMP)
 	PERCPU(PAGE_SIZE)
 #endif
 
@@ -347,15 +308,22 @@ SECTIONS
 		__init_end = .;
 	}
 
+	/*
+	 * smp_locks might be freed after init
+	 * start/end must be page aligned
+	 */
+	. = ALIGN(PAGE_SIZE);
+	.smp_locks : AT(ADDR(.smp_locks) - LOAD_OFFSET) {
+		__smp_locks = .;
+		*(.smp_locks)
+		__smp_locks_end = .;
+		. = ALIGN(PAGE_SIZE);
+	}
+
 #ifdef CONFIG_X86_64
 	.data_nosave : AT(ADDR(.data_nosave) - LOAD_OFFSET) {
-		. = ALIGN(PAGE_SIZE);
-		__nosave_begin = .;
-		*(.data.nosave)
-		. = ALIGN(PAGE_SIZE);
-		__nosave_end = .;
-	} :data.init2
-	/* use another section data.init2, see PERCPU_VADDR() above */
+		NOSAVE_DATA
+	}
 #endif
 
 	/* BSS */
-- 
GitLab


From 5c58ceff103d8a654f24769bb1baaf84a841b0cc Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue, 25 Aug 2009 09:12:43 -0700
Subject: [PATCH 1053/1153] tty: make sure to flush any pending work when
 halting the ldisc

When I rewrote tty ldisc code to use proper reference counts (commits
65b770468e98 and cbe9352fa08f) in order to avoid a race with hangup, the
test-program that Eric Biederman used to trigger the original problem
seems to have exposed another long-standing bug: the hangup code did the
'tty_ldisc_halt()' to stop any buffer flushing activity, but unlike the
other call sites it never actually flushed any pending work.

As a result, if you get just the right timing, the pending work may be
just about to execute (ie the timer has already triggered and thus
cancel_delayed_work() was a no-op), when we then re-initialize the ldisc
from under it.

That, in turn, results in various random problems, usually seen as a
NULL pointer dereference in run_timer_softirq() or a BUG() in
worker_thread (but it can be almost anything).

Fix it by adding the required 'flush_scheduled_work()' after doing the
tty_ldisc_halt() (this also requires us to move the ldisc halt to before
taking the ldisc mutex in order to avoid a deadlock with the workqueue
executing do_tty_hangup, which requires the mutex).

The locking should be cleaned up one day (the requirement to do this
outside the ldisc_mutex is very annoying, and weakens the lock), but
that's a larger and separate undertaking.

Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Xiaotian Feng <xtfeng@gmail.com>
Tested-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/char/tty_ldisc.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/drivers/char/tty_ldisc.c b/drivers/char/tty_ldisc.c
index 1733d3439ad..e48af9f7921 100644
--- a/drivers/char/tty_ldisc.c
+++ b/drivers/char/tty_ldisc.c
@@ -508,8 +508,9 @@ static void tty_ldisc_restore(struct tty_struct *tty, struct tty_ldisc *old)
  *	be obtained while the delayed work queue halt ensures that no more
  *	data is fed to the ldisc.
  *
- *	In order to wait for any existing references to complete see
- *	tty_ldisc_wait_idle.
+ *	You need to do a 'flush_scheduled_work()' (outside the ldisc_mutex)
+ *	in order to make sure any currently executing ldisc work is also
+ *	flushed.
  */
 
 static int tty_ldisc_halt(struct tty_struct *tty)
@@ -753,11 +754,14 @@ void tty_ldisc_hangup(struct tty_struct *tty)
 	 * N_TTY.
 	 */
 	if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS) {
+		/* Make sure the old ldisc is quiescent */
+		tty_ldisc_halt(tty);
+		flush_scheduled_work();
+
 		/* Avoid racing set_ldisc or tty_ldisc_release */
 		mutex_lock(&tty->ldisc_mutex);
 		if (tty->ldisc) {	/* Not yet closed */
 			/* Switch back to N_TTY */
-			tty_ldisc_halt(tty);
 			tty_ldisc_reinit(tty);
 			/* At this point we have a closed ldisc and we want to
 			   reopen it. We could defer this to the next open but
-- 
GitLab


From d8ed1d43e17898761c7221014a15a4c7501d2ff3 Mon Sep 17 00:00:00 2001
From: "David S. Miller" <davem@davemloft.net>
Date: Tue, 25 Aug 2009 16:47:46 -0700
Subject: [PATCH 1054/1153] sparc64: Validate linear D-TLB misses.

When page alloc debugging is not enabled, we essentially accept any
virtual address for linear kernel TLB misses.  But with kgdb, kernel
address probing, and other facilities we can try to access arbitrary
crap.

So, make sure the address we miss on will translate to physical memory
that actually exists.

In order to make this work we have to embed the valid address bitmap
into the kernel image.  And in order to make that less expensive we
make an adjustment, in that the max physical memory address is
decreased to "1 << 41", even on the chips that support a 42-bit
physical address space.  We can do this because bit 41 indicates
"I/O space" and thus covers non-memory ranges.

The result of this is that:

1) kpte_linear_bitmap shrinks from 2K to 1K in size

2) we need 64K more for the valid address bitmap

We can't let the valid address bitmap be dynamically allocated
once we start using it to validate TLB misses, otherwise we have
crazy issues to deal with wrt. recursive TLB misses and such.

If we're in a TLB miss it could be the deepest trap level that's legal
inside of the cpu.  So if we TLB miss referencing the bitmap, the cpu
will be out of trap levels and enter RED state.

To guard against out-of-range accesses to the bitmap, we have to check
to make sure no bits in the physical address above bit 40 are set.  We
could export and use last_valid_pfn for this check, but that's just an
unnecessary extra memory reference.

On the plus side of all this, since we load all of these translations
into the special 4MB mapping TSB, and we check the TSB first for TLB
misses, there should be absolutely no real cost for these new checks
in the TLB miss path.

Reported-by: heyongli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 arch/sparc/include/asm/pgtable_64.h | 12 ++++++--
 arch/sparc/kernel/ktlb.S            | 42 +++++++++++++++++++++++++---
 arch/sparc/mm/init_64.c             | 43 ++++++++++++++++-------------
 arch/sparc/mm/init_64.h             |  7 +++--
 4 files changed, 76 insertions(+), 28 deletions(-)

diff --git a/arch/sparc/include/asm/pgtable_64.h b/arch/sparc/include/asm/pgtable_64.h
index b049abf9902..0ff92fa2206 100644
--- a/arch/sparc/include/asm/pgtable_64.h
+++ b/arch/sparc/include/asm/pgtable_64.h
@@ -726,11 +726,17 @@ extern unsigned long pte_file(pte_t);
 extern pte_t pgoff_to_pte(unsigned long);
 #define PTE_FILE_MAX_BITS	(64UL - PAGE_SHIFT - 1UL)
 
-extern unsigned long *sparc64_valid_addr_bitmap;
+extern unsigned long sparc64_valid_addr_bitmap[];
 
 /* Needs to be defined here and not in linux/mm.h, as it is arch dependent */
-#define kern_addr_valid(addr)	\
-	(test_bit(__pa((unsigned long)(addr))>>22, sparc64_valid_addr_bitmap))
+static inline bool kern_addr_valid(unsigned long addr)
+{
+	unsigned long paddr = __pa(addr);
+
+	if ((paddr >> 41UL) != 0UL)
+		return false;
+	return test_bit(paddr >> 22, sparc64_valid_addr_bitmap);
+}
 
 extern int page_in_phys_avail(unsigned long paddr);
 
diff --git a/arch/sparc/kernel/ktlb.S b/arch/sparc/kernel/ktlb.S
index cef8defcd7a..3ea6e8cde8c 100644
--- a/arch/sparc/kernel/ktlb.S
+++ b/arch/sparc/kernel/ktlb.S
@@ -151,12 +151,46 @@ kvmap_dtlb_4v:
 	 * Must preserve %g1 and %g6 (TAG).
 	 */
 kvmap_dtlb_tsb4m_miss:
-	sethi		%hi(kpte_linear_bitmap), %g2
-	or		%g2, %lo(kpte_linear_bitmap), %g2
+	/* Clear the PAGE_OFFSET top virtual bits, shift
+	 * down to get PFN, and make sure PFN is in range.
+	 */
+	sllx		%g4, 21, %g5
 
-	/* Clear the PAGE_OFFSET top virtual bits, then shift
-	 * down to get a 256MB physical address index.
+	/* Check to see if we know about valid memory at the 4MB
+	 * chunk this physical address will reside within.
 	 */
+	srlx		%g5, 21 + 41, %g2
+	brnz,pn		%g2, kvmap_dtlb_longpath
+	 nop
+
+	/* This unconditional branch and delay-slot nop gets patched
+	 * by the sethi sequence once the bitmap is properly setup.
+	 */
+	.globl		valid_addr_bitmap_insn
+valid_addr_bitmap_insn:
+	ba,pt		%xcc, 2f
+	 nop
+	.subsection	2
+	.globl		valid_addr_bitmap_patch
+valid_addr_bitmap_patch:
+	sethi		%hi(sparc64_valid_addr_bitmap), %g7
+	or		%g7, %lo(sparc64_valid_addr_bitmap), %g7
+	.previous
+
+	srlx		%g5, 21 + 22, %g2
+	srlx		%g2, 6, %g5
+	and		%g2, 63, %g2
+	sllx		%g5, 3, %g5
+	ldx		[%g7 + %g5], %g5
+	mov		1, %g7
+	sllx		%g7, %g2, %g7
+	andcc		%g5, %g7, %g0
+	be,pn		%xcc, kvmap_dtlb_longpath
+
+2:	 sethi		%hi(kpte_linear_bitmap), %g2
+	or		%g2, %lo(kpte_linear_bitmap), %g2
+
+	/* Get the 256MB physical address index. */
 	sllx		%g4, 21, %g5
 	mov		1, %g7
 	srlx		%g5, 21 + 28, %g5
diff --git a/arch/sparc/mm/init_64.c b/arch/sparc/mm/init_64.c
index ed6be6ba2f4..a70a5e1904d 100644
--- a/arch/sparc/mm/init_64.c
+++ b/arch/sparc/mm/init_64.c
@@ -145,7 +145,8 @@ static void __init read_obp_memory(const char *property,
 	     cmp_p64, NULL);
 }
 
-unsigned long *sparc64_valid_addr_bitmap __read_mostly;
+unsigned long sparc64_valid_addr_bitmap[VALID_ADDR_BITMAP_BYTES /
+					sizeof(unsigned long)];
 EXPORT_SYMBOL(sparc64_valid_addr_bitmap);
 
 /* Kernel physical address base and size in bytes.  */
@@ -1874,7 +1875,7 @@ static int pavail_rescan_ents __initdata;
  * memory list again, and make sure it provides at least as much
  * memory as 'pavail' does.
  */
-static void __init setup_valid_addr_bitmap_from_pavail(void)
+static void __init setup_valid_addr_bitmap_from_pavail(unsigned long *bitmap)
 {
 	int i;
 
@@ -1897,8 +1898,7 @@ static void __init setup_valid_addr_bitmap_from_pavail(void)
 
 				if (new_start <= old_start &&
 				    new_end >= (old_start + PAGE_SIZE)) {
-					set_bit(old_start >> 22,
-						sparc64_valid_addr_bitmap);
+					set_bit(old_start >> 22, bitmap);
 					goto do_next_page;
 				}
 			}
@@ -1919,20 +1919,21 @@ static void __init setup_valid_addr_bitmap_from_pavail(void)
 	}
 }
 
+static void __init patch_tlb_miss_handler_bitmap(void)
+{
+	extern unsigned int valid_addr_bitmap_insn[];
+	extern unsigned int valid_addr_bitmap_patch[];
+
+	valid_addr_bitmap_insn[1] = valid_addr_bitmap_patch[1];
+	mb();
+	valid_addr_bitmap_insn[0] = valid_addr_bitmap_patch[0];
+	flushi(&valid_addr_bitmap_insn[0]);
+}
+
 void __init mem_init(void)
 {
 	unsigned long codepages, datapages, initpages;
 	unsigned long addr, last;
-	int i;
-
-	i = last_valid_pfn >> ((22 - PAGE_SHIFT) + 6);
-	i += 1;
-	sparc64_valid_addr_bitmap = (unsigned long *) alloc_bootmem(i << 3);
-	if (sparc64_valid_addr_bitmap == NULL) {
-		prom_printf("mem_init: Cannot alloc valid_addr_bitmap.\n");
-		prom_halt();
-	}
-	memset(sparc64_valid_addr_bitmap, 0, i << 3);
 
 	addr = PAGE_OFFSET + kern_base;
 	last = PAGE_ALIGN(kern_size) + addr;
@@ -1941,15 +1942,19 @@ void __init mem_init(void)
 		addr += PAGE_SIZE;
 	}
 
-	setup_valid_addr_bitmap_from_pavail();
+	setup_valid_addr_bitmap_from_pavail(sparc64_valid_addr_bitmap);
+	patch_tlb_miss_handler_bitmap();
 
 	high_memory = __va(last_valid_pfn << PAGE_SHIFT);
 
 #ifdef CONFIG_NEED_MULTIPLE_NODES
-	for_each_online_node(i) {
-		if (NODE_DATA(i)->node_spanned_pages != 0) {
-			totalram_pages +=
-				free_all_bootmem_node(NODE_DATA(i));
+	{
+		int i;
+		for_each_online_node(i) {
+			if (NODE_DATA(i)->node_spanned_pages != 0) {
+				totalram_pages +=
+					free_all_bootmem_node(NODE_DATA(i));
+			}
 		}
 	}
 #else
diff --git a/arch/sparc/mm/init_64.h b/arch/sparc/mm/init_64.h
index 16063870a48..c2f772dbd55 100644
--- a/arch/sparc/mm/init_64.h
+++ b/arch/sparc/mm/init_64.h
@@ -5,10 +5,13 @@
  * marked non-static so that assembler code can get at them.
  */
 
-#define MAX_PHYS_ADDRESS	(1UL << 42UL)
-#define KPTE_BITMAP_CHUNK_SZ	(256UL * 1024UL * 1024UL)
+#define MAX_PHYS_ADDRESS	(1UL << 41UL)
+#define KPTE_BITMAP_CHUNK_SZ		(256UL * 1024UL * 1024UL)
 #define KPTE_BITMAP_BYTES	\
 	((MAX_PHYS_ADDRESS / KPTE_BITMAP_CHUNK_SZ) / 8)
+#define VALID_ADDR_BITMAP_CHUNK_SZ	(4UL * 1024UL * 1024UL)
+#define VALID_ADDR_BITMAP_BYTES	\
+	((MAX_PHYS_ADDRESS / VALID_ADDR_BITMAP_CHUNK_SZ) / 8)
 
 extern unsigned long kern_linear_pte_xor[2];
 extern unsigned long kpte_linear_bitmap[KPTE_BITMAP_BYTES / sizeof(unsigned long)];
-- 
GitLab


From 730a9cfc2dcead5538c0c96a046000d97140b0c0 Mon Sep 17 00:00:00 2001
From: Alexander Beregalov <a.beregalov@gmail.com>
Date: Tue, 25 Aug 2009 20:39:18 -0700
Subject: [PATCH 1055/1153] irda/au1k_ir: fix broken netdev_ops conversion

This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect
net_device_ops). Do the same for au1k_ir.
Untested.

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/irda/au1k_ir.c | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/drivers/net/irda/au1k_ir.c b/drivers/net/irda/au1k_ir.c
index c4361d46659..ee1cff5c9b2 100644
--- a/drivers/net/irda/au1k_ir.c
+++ b/drivers/net/irda/au1k_ir.c
@@ -23,7 +23,6 @@
 #include <linux/init.h>
 #include <linux/errno.h>
 #include <linux/netdevice.h>
-#include <linux/etherdevice.h>
 #include <linux/slab.h>
 #include <linux/rtnetlink.h>
 #include <linux/interrupt.h>
@@ -205,9 +204,6 @@ static const struct net_device_ops au1k_irda_netdev_ops = {
 	.ndo_start_xmit		= au1k_irda_hard_xmit,
 	.ndo_tx_timeout		= au1k_tx_timeout,
 	.ndo_do_ioctl		= au1k_irda_ioctl,
-	.ndo_change_mtu		= eth_change_mtu,
-	.ndo_validate_addr	= eth_validate_addr,
-	.ndo_set_mac_address	= eth_mac_addr,
 };
 
 static int au1k_irda_net_init(struct net_device *dev)
-- 
GitLab


From 4484b9c8b4976acee181d377f8ba571109d1a2be Mon Sep 17 00:00:00 2001
From: Alexander Beregalov <a.beregalov@gmail.com>
Date: Tue, 25 Aug 2009 20:39:37 -0700
Subject: [PATCH 1056/1153] irda/sa1100_ir: fix broken netdev_ops conversion

This patch is based on commit d2f3ad4 (pxaficp-ir: remove incorrect
net_device_ops). Do the same for sa1100_ir.
Untested.

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/irda/sa1100_ir.c | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/drivers/net/irda/sa1100_ir.c b/drivers/net/irda/sa1100_ir.c
index 2aeb2e6aec1..b039cb081e9 100644
--- a/drivers/net/irda/sa1100_ir.c
+++ b/drivers/net/irda/sa1100_ir.c
@@ -24,7 +24,6 @@
 #include <linux/init.h>
 #include <linux/errno.h>
 #include <linux/netdevice.h>
-#include <linux/etherdevice.h>
 #include <linux/slab.h>
 #include <linux/rtnetlink.h>
 #include <linux/interrupt.h>
@@ -881,9 +880,6 @@ static const struct net_device_ops sa1100_irda_netdev_ops = {
 	.ndo_stop		= sa1100_irda_stop,
 	.ndo_start_xmit		= sa1100_irda_hard_xmit,
 	.ndo_do_ioctl		= sa1100_irda_ioctl,
-	.ndo_change_mtu		= eth_change_mtu,
-	.ndo_validate_addr	= eth_validate_addr,
-	.ndo_set_mac_address	= eth_mac_addr,
 };
 
 static int sa1100_irda_probe(struct platform_device *pdev)
-- 
GitLab


From d560bc61575efae43595cbcb56d0ba3b9450139c Mon Sep 17 00:00:00 2001
From: Jeremy Fitzhardinge <jeremy@goop.org>
Date: Tue, 25 Aug 2009 12:53:02 -0700
Subject: [PATCH 1057/1153] x86, xen: Suppress WP test on Xen

Xen always runs on CPUs which properly support WP enforcement in
privileged mode, so there's no need to test for it.

This also works around a crash reported by Arnd Hannemann, though I
think its just a band-aid for that case.

Reported-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
---
 arch/x86/xen/enlighten.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/x86/xen/enlighten.c b/arch/x86/xen/enlighten.c
index e90540a46a0..0b755cd7686 100644
--- a/arch/x86/xen/enlighten.c
+++ b/arch/x86/xen/enlighten.c
@@ -1059,6 +1059,7 @@ asmlinkage void __init xen_start_kernel(void)
 	/* set up basic CPUID stuff */
 	cpu_detect(&new_cpu_data);
 	new_cpu_data.hard_math = 1;
+	new_cpu_data.wp_works_ok = 1;
 	new_cpu_data.x86_capability[0] = cpuid_edx(1);
 #endif
 
-- 
GitLab


From 7adb4df410966dfe43e4815256e3215110648fb8 Mon Sep 17 00:00:00 2001
From: "H. Peter Anvin" <hpa@zytor.com>
Date: Tue, 25 Aug 2009 21:06:03 -0700
Subject: [PATCH 1058/1153] x86, xen: Initialize cx to suppress warning

Initialize cx before calling xen_cpuid(), in order to suppress the
"may be used uninitialized in this function" warning.

Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
---
 arch/x86/xen/enlighten.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/x86/xen/enlighten.c b/arch/x86/xen/enlighten.c
index 0b755cd7686..eb33aaa8415 100644
--- a/arch/x86/xen/enlighten.c
+++ b/arch/x86/xen/enlighten.c
@@ -215,6 +215,7 @@ static __init void xen_init_cpuid_mask(void)
 			  (1 << X86_FEATURE_ACPI));  /* disable ACPI */
 
 	ax = 1;
+	cx = 0;
 	xen_cpuid(&ax, &bx, &cx, &dx);
 
 	/* cpuid claims we support xsave; try enabling it to see what happens */
-- 
GitLab


From 295594e9cf6ae2efd73371777aa8feba0f87f42f Mon Sep 17 00:00:00 2001
From: Yinghai Lu <yinghai@kernel.org>
Date: Tue, 25 Aug 2009 13:44:44 -0700
Subject: [PATCH 1059/1153] x86: Fix vSMP boot crash

2.6.31-rc7 does not boot on vSMP systems:

[    8.501108] CPU31: Thermal monitoring enabled (TM1)
[    8.501127] CPU 31 MCA banks SHD:2 SHD:3 SHD:5 SHD:6 SHD:8
[    8.650254] CPU31: Intel(R) Xeon(R) CPU           E5540  @ 2.53GHz stepping 04
[    8.710324] Brought up 32 CPUs
[    8.713916] Total of 32 processors activated (162314.96 BogoMIPS).
[    8.721489] ERROR: parent span is not a superset of domain->span
[    8.727686] ERROR: domain->groups does not contain CPU0
[    8.733091] ERROR: groups don't span domain->span
[    8.737975] ERROR: domain->cpu_power not set
[    8.742416]

Ravikiran Thirumalai bisected it to:

| commit 2759c3287de27266e06f1f4e82cbd2d65f6a044c
| x86: don't call read_apic_id if !cpu_has_apic

The problem is that on vSMP systems the CPUID derived
initial-APICIDs are overlapping - so we need to fall
back on hard_smp_processor_id() which reads the local
APIC.

Both come from the hardware (influenced by firmware
though) so it's a tough call which one to trust.

Doing the quirk expresses the vSMP property properly
and also does not affect other systems, so we go for
this solution instead of a revert.

Reported-and-Tested-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shai Fultheim <shai@scalex86.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4A944D3C.5030100@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
 arch/x86/kernel/apic/probe_64.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/x86/kernel/apic/probe_64.c b/arch/x86/kernel/apic/probe_64.c
index bc3e880f9b8..fcec2f1d34a 100644
--- a/arch/x86/kernel/apic/probe_64.c
+++ b/arch/x86/kernel/apic/probe_64.c
@@ -44,6 +44,11 @@ static struct apic *apic_probe[] __initdata = {
 	NULL,
 };
 
+static int apicid_phys_pkg_id(int initial_apic_id, int index_msb)
+{
+	return hard_smp_processor_id() >> index_msb;
+}
+
 /*
  * Check the APIC IDs in bios_cpu_apicid and choose the APIC mode.
  */
@@ -69,6 +74,11 @@ void __init default_setup_apic_routing(void)
 		printk(KERN_INFO "Setting APIC routing to %s\n", apic->name);
 	}
 
+	if (is_vsmp_box()) {
+		/* need to update phys_pkg_id */
+		apic->phys_pkg_id = apicid_phys_pkg_id;
+	}
+
 	/*
 	 * Now that apic routing model is selected, configure the
 	 * fault handling for intr remapping.
-- 
GitLab


From 0b4f2928f14c4a9770b0866923fc81beb7f4aa57 Mon Sep 17 00:00:00 2001
From: Alexey Dobriyan <adobriyan@gmail.com>
Date: Wed, 26 Aug 2009 12:03:35 -0700
Subject: [PATCH 1060/1153] smc91x: fix compilation on SMP

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/smc91x.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/smc91x.c b/drivers/net/smc91x.c
index 9da1fa12a67..7567f510eff 100644
--- a/drivers/net/smc91x.c
+++ b/drivers/net/smc91x.c
@@ -531,7 +531,7 @@ static inline void  smc_rcv(struct net_device *dev)
 		local_irq_restore(flags);				\
 	__ret;								\
 })
-#define smc_special_lock(lock, flags)		spin_lock_irq(lock, flags)
+#define smc_special_lock(lock, flags)		spin_lock_irqsave(lock, flags)
 #define smc_special_unlock(lock, flags) 	spin_unlock_irqrestore(lock, flags)
 #else
 #define smc_special_trylock(lock, flags)	(1)
-- 
GitLab


From 3161e453e496eb5643faad30fff5a5ab183da0fe Mon Sep 17 00:00:00 2001
From: Rusty Russell <rusty@rustcorp.com.au>
Date: Wed, 26 Aug 2009 12:22:32 -0700
Subject: [PATCH 1061/1153] virtio: net refill on out-of-memory

If we run out of memory, use keventd to fill the buffer.  There's a
report of this happening: "Page allocation failures in guest",
Message-ID: <20090713115158.0a4892b0@mjolnir.ossman.eu>

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
 drivers/net/virtio_net.c | 61 ++++++++++++++++++++++++++++++----------
 1 file changed, 46 insertions(+), 15 deletions(-)

diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
index 2a6e81d5b57..bbedf03a212 100644
--- a/drivers/net/virtio_net.c
+++ b/drivers/net/virtio_net.c
@@ -70,6 +70,9 @@ struct virtnet_info
 	struct sk_buff_head recv;
 	struct sk_buff_head send;
 
+	/* Work struct for refilling if we run low on memory. */
+	struct delayed_work refill;
+
 	/* Chain pages by the private ptr. */
 	struct page *pages;
 };
@@ -273,19 +276,22 @@ drop:
 	dev_kfree_skb(skb);
 }
 
-static void try_fill_recv_maxbufs(struct virtnet_info *vi)
+static bool try_fill_recv_maxbufs(struct virtnet_info *vi, gfp_t gfp)
 {
 	struct sk_buff *skb;
 	struct scatterlist sg[2+MAX_SKB_FRAGS];
 	int num, err, i;
+	bool oom = false;
 
 	sg_init_table(sg, 2+MAX_SKB_FRAGS);
 	for (;;) {
 		struct virtio_net_hdr *hdr;
 
 		skb = netdev_alloc_skb(vi->dev, MAX_PACKET_LEN + NET_IP_ALIGN);
-		if (unlikely(!skb))
+		if (unlikely(!skb)) {
+			oom = true;
 			break;
+		}
 
 		skb_reserve(skb, NET_IP_ALIGN);
 		skb_put(skb, MAX_PACKET_LEN);
@@ -296,7 +302,7 @@ static void try_fill_recv_maxbufs(struct virtnet_info *vi)
 		if (vi->big_packets) {
 			for (i = 0; i < MAX_SKB_FRAGS; i++) {
 				skb_frag_t *f = &skb_shinfo(skb)->frags[i];
-				f->page = get_a_page(vi, GFP_ATOMIC);
+				f->page = get_a_page(vi, gfp);
 				if (!f->page)
 					break;
 
@@ -325,31 +331,35 @@ static void try_fill_recv_maxbufs(struct virtnet_info *vi)
 	if (unlikely(vi->num > vi->max))
 		vi->max = vi->num;
 	vi->rvq->vq_ops->kick(vi->rvq);
+	return !oom;
 }
 
-static void try_fill_recv(struct virtnet_info *vi)
+/* Returns false if we couldn't fill entirely (OOM). */
+static bool try_fill_recv(struct virtnet_info *vi, gfp_t gfp)
 {
 	struct sk_buff *skb;
 	struct scatterlist sg[1];
 	int err;
+	bool oom = false;
 
-	if (!vi->mergeable_rx_bufs) {
-		try_fill_recv_maxbufs(vi);
-		return;
-	}
+	if (!vi->mergeable_rx_bufs)
+		return try_fill_recv_maxbufs(vi, gfp);
 
 	for (;;) {
 		skb_frag_t *f;
 
 		skb = netdev_alloc_skb(vi->dev, GOOD_COPY_LEN + NET_IP_ALIGN);
-		if (unlikely(!skb))
+		if (unlikely(!skb)) {
+			oom = true;
 			break;
+		}
 
 		skb_reserve(skb, NET_IP_ALIGN);
 
 		f = &skb_shinfo(skb)->frags[0];
-		f->page = get_a_page(vi, GFP_ATOMIC);
+		f->page = get_a_page(vi, gfp);
 		if (!f->page) {
+			oom = true;
 			kfree_skb(skb);
 			break;
 		}
@@ -373,6 +383,7 @@ static void try_fill_recv(struct virtnet_info *vi)
 	if (unlikely(vi->num > vi->max))
 		vi->max = vi->num;
 	vi->rvq->vq_ops->kick(vi->rvq);
+	return !oom;
 }
 
 static void skb_recv_done(struct virtqueue *rvq)
@@ -385,6 +396,23 @@ static void skb_recv_done(struct virtqueue *rvq)
 	}
 }
 
+static void refill_work(struct work_struct *work)
+{
+	struct virtnet_info *vi;
+	bool still_empty;
+
+	vi = container_of(work, struct virtnet_info, refill.work);
+	napi_disable(&vi->napi);
+	try_fill_recv(vi, GFP_KERNEL);
+	still_empty = (vi->num == 0);
+	napi_enable(&vi->napi);
+
+	/* In theory, this can happen: if we don't get any buffers in
+	 * we will *never* try to fill again. */
+	if (still_empty)
+		schedule_delayed_work(&vi->refill, HZ/2);
+}
+
 static int virtnet_poll(struct napi_struct *napi, int budget)
 {
 	struct virtnet_info *vi = container_of(napi, struct virtnet_info, napi);
@@ -400,10 +428,10 @@ again:
 		received++;
 	}
 
-	/* FIXME: If we oom and completely run out of inbufs, we need
-	 * to start a timer trying to fill more. */
-	if (vi->num < vi->max / 2)
-		try_fill_recv(vi);
+	if (vi->num < vi->max / 2) {
+		if (!try_fill_recv(vi, GFP_ATOMIC))
+			schedule_delayed_work(&vi->refill, 0);
+	}
 
 	/* Out of packets? */
 	if (received < budget) {
@@ -893,6 +921,7 @@ static int virtnet_probe(struct virtio_device *vdev)
 	vi->vdev = vdev;
 	vdev->priv = vi;
 	vi->pages = NULL;
+	INIT_DELAYED_WORK(&vi->refill, refill_work);
 
 	/* If they give us a callback when all buffers are done, we don't need
 	 * the timer. */
@@ -941,7 +970,7 @@ static int virtnet_probe(struct virtio_device *vdev)
 	}
 
 	/* Last of all, set up some receive buffers. */
-	try_fill_recv(vi);
+	try_fill_recv(vi, GFP_KERNEL);
 
 	/* If we didn't even get one input buffer, we're useless. */
 	if (vi->num == 0) {
@@ -958,6 +987,7 @@ static int virtnet_probe(struct virtio_device *vdev)
 
 unregister:
 	unregister_netdev(dev);
+	cancel_delayed_work_sync(&vi->refill);
 free_vqs:
 	vdev->config->del_vqs(vdev);
 free:
@@ -986,6 +1016,7 @@ static void virtnet_remove(struct virtio_device *vdev)
 	BUG_ON(vi->num != 0);
 
 	unregister_netdev(vi->dev);
+	cancel_delayed_work_sync(&vi->refill);
 
 	vdev->config->del_vqs(vi->vdev);
 
-- 
GitLab


From dac9ff79a8122b30176e23359bb879b3144d7f1f Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Wed, 17 Jun 2009 13:13:56 -0700
Subject: [PATCH 1062/1153] m68k: count can reach 51, not 50

With while (count++ < 50) { ...  } count can reach 51, not 50, so we
shouldn't give an error message on a count of 50.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
 drivers/macintosh/via-maciisi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/macintosh/via-maciisi.c b/drivers/macintosh/via-maciisi.c
index 4d686c0bdea..9ab5b0c34f0 100644
--- a/drivers/macintosh/via-maciisi.c
+++ b/drivers/macintosh/via-maciisi.c
@@ -288,7 +288,7 @@ static void maciisi_sync(struct adb_request *req)
 	}
 	/* This could be BAD... when the ADB controller doesn't respond
 	 * for this long, it's probably not coming back :-( */
-	if(count >= 50) /* Hopefully shouldn't happen */
+	if (count > 50) /* Hopefully shouldn't happen */
 		printk(KERN_ERR "maciisi_send_request: poll timed out!\n");
 }
 
-- 
GitLab


From dd9b3e84f2095ed19582f4df5d20e1e40c01ca3c Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Wed, 17 Jun 2009 13:13:57 -0700
Subject: [PATCH 1063/1153] m68k: cnt reaches -1, not 0

With the postfix decrement cnt reaches -1 rather than 0.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
 arch/m68k/amiga/config.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/m68k/amiga/config.c b/arch/m68k/amiga/config.c
index 6e562751ad5..6c74751c7b8 100644
--- a/arch/m68k/amiga/config.c
+++ b/arch/m68k/amiga/config.c
@@ -574,10 +574,11 @@ static int a2000_hwclk(int op, struct rtc_time *t)
 
 	tod_2000.cntrl1 = TOD2000_CNTRL1_HOLD;
 
-	while ((tod_2000.cntrl1 & TOD2000_CNTRL1_BUSY) && cnt--) {
+	while ((tod_2000.cntrl1 & TOD2000_CNTRL1_BUSY) && cnt) {
 		tod_2000.cntrl1 &= ~TOD2000_CNTRL1_HOLD;
 		udelay(70);
 		tod_2000.cntrl1 |= TOD2000_CNTRL1_HOLD;
+		--cnt;
 	}
 
 	if (!cnt)
@@ -649,10 +650,11 @@ static int amiga_set_clock_mmss(unsigned long nowtime)
 
 		tod_2000.cntrl1 |= TOD2000_CNTRL1_HOLD;
 
-		while ((tod_2000.cntrl1 & TOD2000_CNTRL1_BUSY) && cnt--) {
+		while ((tod_2000.cntrl1 & TOD2000_CNTRL1_BUSY) && cnt) {
 			tod_2000.cntrl1 &= ~TOD2000_CNTRL1_HOLD;
 			udelay(70);
 			tod_2000.cntrl1 |= TOD2000_CNTRL1_HOLD;
+			--cnt;
 		}
 
 		if (!cnt)
-- 
GitLab


From dc71c7d5dbd8cd8bb6e3b548ddc0454b64ded5f8 Mon Sep 17 00:00:00 2001
From: Andrew Morton <akpm@linux-foundation.org>
Date: Wed, 17 Jun 2009 13:13:58 -0700
Subject: [PATCH 1064/1153] arch/m68k/include/asm/motorola_pgalloc.h: fix
 kunmap arg

arch/m68k/include/asm/motorola_pgalloc.h: In function 'pte_alloc_one':
arch/m68k/include/asm/motorola_pgalloc.h:44: warning: passing argument 1 of 'kunmap' from incompatible pointer type

Also, remove unneeded test for kmap() failure.

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
 arch/m68k/include/asm/motorola_pgalloc.h | 10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)

diff --git a/arch/m68k/include/asm/motorola_pgalloc.h b/arch/m68k/include/asm/motorola_pgalloc.h
index 15ee4c74a9f..2f02f264e69 100644
--- a/arch/m68k/include/asm/motorola_pgalloc.h
+++ b/arch/m68k/include/asm/motorola_pgalloc.h
@@ -36,12 +36,10 @@ static inline pgtable_t pte_alloc_one(struct mm_struct *mm, unsigned long addres
 		return NULL;
 
 	pte = kmap(page);
-	if (pte) {
-		__flush_page_to_ram(pte);
-		flush_tlb_kernel_page(pte);
-		nocache_page(pte);
-	}
-	kunmap(pte);
+	__flush_page_to_ram(pte);
+	flush_tlb_kernel_page(pte);
+	nocache_page(pte);
+	kunmap(page);
 	pgtable_page_ctor(page);
 	return page;
 }
-- 
GitLab


From 9fd926b4ab1e38ac5e3eb3ba0afb56726d90aa88 Mon Sep 17 00:00:00 2001
From: Alexey Dobriyan <adobriyan@gmail.com>
Date: Thu, 9 Jul 2009 17:08:38 +0400
Subject: [PATCH 1065/1153] m68k: Fix redefinition of pgprot_noncached

arch/m68k/include/asm/pgtable_mm.h:148:1: warning: "pgprot_noncached" redefined
In file included from arch/m68k/include/asm/pgtable_mm.h:138,
                 from arch/m68k/include/asm/pgtable.h:4,
                 from include/linux/mm.h:40,
                 from include/linux/pagemap.h:7,
                 from include/linux/blkdev.h:12,
                 from arch/m68k/emu/nfblock.c:17:
include/asm-generic/pgtable.h:133:1: warning: this is the location of the previous definition

pgprot_noncached() should be defined _before_ including asm-generic/pgtable.h

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
---
 arch/m68k/include/asm/pgtable_mm.h | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/m68k/include/asm/pgtable_mm.h b/arch/m68k/include/asm/pgtable_mm.h
index 0b604f0f192..fe60e1abaee 100644
--- a/arch/m68k/include/asm/pgtable_mm.h
+++ b/arch/m68k/include/asm/pgtable_mm.h
@@ -135,8 +135,6 @@ static inline void update_mmu_cache(struct vm_area_struct *vma,
 #endif
 
 #ifndef __ASSEMBLY__
-#include <asm-generic/pgtable.h>
-
 /*
  * Macro to mark a page protection value as "uncacheable".
  */
@@ -154,6 +152,7 @@ static inline void update_mmu_cache(struct vm_area_struct *vma,
 	    ? (__pgprot((pgprot_val(prot) & _CACHEMASK040) | _PAGE_NOCACHE_S))	\
 	    : (prot)))
 
+#include <asm-generic/pgtable.h>
 #endif /* !__ASSEMBLY__ */
 
 /*
-- 
GitLab


From 9848484fad9ddeb18f18f02f9ecdcd330ac9a216 Mon Sep 17 00:00:00 2001
From: Geert Uytterhoeven <geert@linux-m68k.org>
Date: Fri, 21 Aug 2009 22:03:54 +0200
Subject: [PATCH 1066/1153] m68k,m68knommu: Wire up rt_tgsigqueueinfo and
 perf_counter_open

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
---
 arch/m68k/include/asm/unistd.h       | 4 +++-
 arch/m68k/kernel/entry.S             | 2 ++
 arch/m68knommu/kernel/syscalltable.S | 2 ++
 3 files changed, 7 insertions(+), 1 deletion(-)

diff --git a/arch/m68k/include/asm/unistd.h b/arch/m68k/include/asm/unistd.h
index aa29a8640f7..946d8691f2b 100644
--- a/arch/m68k/include/asm/unistd.h
+++ b/arch/m68k/include/asm/unistd.h
@@ -334,10 +334,12 @@
 #define __NR_inotify_init1	328
 #define __NR_preadv		329
 #define __NR_pwritev		330
+#define __NR_rt_tgsigqueueinfo	331
+#define __NR_perf_counter_open	332
 
 #ifdef __KERNEL__
 
-#define NR_syscalls		331
+#define NR_syscalls		333
 
 #define __ARCH_WANT_IPC_PARSE_VERSION
 #define __ARCH_WANT_OLD_READDIR
diff --git a/arch/m68k/kernel/entry.S b/arch/m68k/kernel/entry.S
index 8744f60c07a..c3735cd6207 100644
--- a/arch/m68k/kernel/entry.S
+++ b/arch/m68k/kernel/entry.S
@@ -755,4 +755,6 @@ sys_call_table:
 	.long sys_inotify_init1
 	.long sys_preadv
 	.long sys_pwritev		/* 330 */
+	.long sys_rt_tgsigqueueinfo
+	.long sys_perf_counter_open
 
diff --git a/arch/m68knommu/kernel/syscalltable.S b/arch/m68knommu/kernel/syscalltable.S
index c0b8782832f..0ae123e0898 100644
--- a/arch/m68knommu/kernel/syscalltable.S
+++ b/arch/m68knommu/kernel/syscalltable.S
@@ -349,6 +349,8 @@ ENTRY(sys_call_table)
 	.long sys_inotify_init1
 	.long sys_preadv
 	.long sys_pwritev		/* 330 */
+	.long sys_rt_tgsigqueueinfo
+	.long sys_perf_counter_open
 
 	.rept NR_syscalls-(.-sys_call_table)/4
 		.long sys_ni_syscall
-- 
GitLab


From 53a7197aff20e341487fca8575275056fe1c63e5 Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Wed, 26 Aug 2009 14:56:48 -0400
Subject: [PATCH 1067/1153] IMA: iint put in ima_counts_get and put

ima_counts_get() calls ima_iint_find_insert_get() which takes a reference
to the iint in question, but does not put that reference at the end of the
function.  This can lead to a nasty memory leak.  Easy enough to reproduce:

#include <sys/mman.h>
#include <stdio.h>

int main (void)
{
	int i;
	void *ptr;

	for (i=0; i < 100000; i++) {
		ptr = mmap(NULL, 4096, PROT_READ|PROT_WRITE,
			   MAP_SHARED|MAP_ANONYMOUS, -1, 0);
		if (ptr == MAP_FAILED)
			return 2;
		munmap(ptr, 4096);
	}

	return 0;
}

Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
---
 security/integrity/ima/ima_main.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/security/integrity/ima/ima_main.c b/security/integrity/ima/ima_main.c
index 101c512564e..4732f5e5d12 100644
--- a/security/integrity/ima/ima_main.c
+++ b/security/integrity/ima/ima_main.c
@@ -262,6 +262,8 @@ void ima_counts_put(struct path *path, int mask)
 	else if (mask & (MAY_READ | MAY_EXEC))
 		iint->readcount--;
 	mutex_unlock(&iint->mutex);
+
+	kref_put(&iint->refcount, iint_free);
 }
 
 /*
@@ -291,6 +293,8 @@ void ima_counts_get(struct file *file)
 	if (file->f_mode & FMODE_WRITE)
 		iint->writecount++;
 	mutex_unlock(&iint->mutex);
+
+	kref_put(&iint->refcount, iint_free);
 }
 EXPORT_SYMBOL_GPL(ima_counts_get);
 
-- 
GitLab


From 054b2b13ccba4876a1ce98a7ede7dab7d6893d01 Mon Sep 17 00:00:00 2001
From: Joonwoo Park <joonwpark81@gmail.com>
Date: Wed, 26 Aug 2009 14:29:18 -0700
Subject: [PATCH 1068/1153] pps: fix incorrect verdict check

Fix incorrect verdict check and returns error if device_create failed,
otherwise driver triggers kernel oops.

Signed-off-by: Joonwoo Park<joonwpark81@gmail.com>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/pps/pps.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/pps/pps.c b/drivers/pps/pps.c
index ac8cc8cea1e..fea17e7805e 100644
--- a/drivers/pps/pps.c
+++ b/drivers/pps/pps.c
@@ -244,7 +244,7 @@ int pps_register_cdev(struct pps_device *pps)
 	}
 	pps->dev = device_create(pps_class, pps->info.dev, pps->devno, NULL,
 							"pps%d", pps->id);
-	if (err)
+	if (IS_ERR(pps->dev))
 		goto del_cdev;
 	dev_set_drvdata(pps->dev, pps);
 
-- 
GitLab


From a30b595d2ca6d39e784a1bed5f2b35f3d7a03af7 Mon Sep 17 00:00:00 2001
From: David Rientjes <rientjes@google.com>
Date: Wed, 26 Aug 2009 14:29:20 -0700
Subject: [PATCH 1069/1153] flex_array: fix get function for elements in base
 starting at non-zero

If all array elements fit into the base structure and data is copied using
flex_array_put() starting at a non-zero index, flex_array_get() will fail
to return the data.

This fixes the bug by only checking for NULL parts when all elements do
not fit in the base structure when flex_array_get() is used.  Otherwise,
fa_element_to_part_nr() will always be 0 since there are no parts
structures needed and such element may never have been put.  Thus, it will
remain NULL due to the kzalloc() of the base.

Additionally, flex_array_put() now only checks for a NULL part when all
elements do not fit in the base structure.  This is otherwise unnecessary
since the base structure is guaranteed to exist (or we would have already
hit a NULL pointer).

Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 lib/flex_array.c | 14 ++++++++------
 1 file changed, 8 insertions(+), 6 deletions(-)

diff --git a/lib/flex_array.c b/lib/flex_array.c
index 08f1636d296..e73c691aec3 100644
--- a/lib/flex_array.c
+++ b/lib/flex_array.c
@@ -198,10 +198,11 @@ int flex_array_put(struct flex_array *fa, int element_nr, void *src, gfp_t flags
 		return -ENOSPC;
 	if (elements_fit_in_base(fa))
 		part = (struct flex_array_part *)&fa->parts[0];
-	else
+	else {
 		part = __fa_get_part(fa, part_nr, flags);
-	if (!part)
-		return -ENOMEM;
+		if (!part)
+			return -ENOMEM;
+	}
 	dst = &part->elements[index_inside_part(fa, element_nr)];
 	memcpy(dst, src, fa->element_size);
 	return 0;
@@ -257,11 +258,12 @@ void *flex_array_get(struct flex_array *fa, int element_nr)
 
 	if (element_nr >= fa->total_nr_elements)
 		return NULL;
-	if (!fa->parts[part_nr])
-		return NULL;
 	if (elements_fit_in_base(fa))
 		part = (struct flex_array_part *)&fa->parts[0];
-	else
+	else {
 		part = fa->parts[part_nr];
+		if (!part)
+			return NULL;
+	}
 	return &part->elements[index_inside_part(fa, element_nr)];
 }
-- 
GitLab


From 105b6e8a74cac11cdf70903877593c7f202075cc Mon Sep 17 00:00:00 2001
From: David Rientjes <rientjes@google.com>
Date: Wed, 26 Aug 2009 14:29:20 -0700
Subject: [PATCH 1070/1153] flex_array: fix flex_array_free_parts comment

flex_array_free_parts() does not take `src' or `element_nr' formals, so
remove their respective comments.

Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 lib/flex_array.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/lib/flex_array.c b/lib/flex_array.c
index e73c691aec3..cf4e372cae9 100644
--- a/lib/flex_array.c
+++ b/lib/flex_array.c
@@ -122,9 +122,6 @@ static int fa_element_to_part_nr(struct flex_array *fa, int element_nr)
 
 /**
  * flex_array_free_parts - just free the second-level pages
- * @src:	address of data to copy into the array
- * @element_nr:	index of the position in which to insert
- * 		the new element.
  *
  * This is to be used in cases where the base 'struct flex_array'
  * has been statically allocated and should not be free.
-- 
GitLab


From 8e7ee27095aee87b5db1b0061e2ceea5878a1bbd Mon Sep 17 00:00:00 2001
From: David Rientjes <rientjes@google.com>
Date: Wed, 26 Aug 2009 14:29:21 -0700
Subject: [PATCH 1071/1153] flex_array: declare parts member to have incomplete
 type

The `parts' member of struct flex_array should evaluate to an incomplete
type so that sizeof() cannot be used and C99 does not require the
zero-length specification.

Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/flex_array.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/flex_array.h b/include/linux/flex_array.h
index 23c1ec79a31..603160db7c9 100644
--- a/include/linux/flex_array.h
+++ b/include/linux/flex_array.h
@@ -21,7 +21,7 @@ struct flex_array {
 		struct {
 			int element_size;
 			int total_nr_elements;
-			struct flex_array_part *parts[0];
+			struct flex_array_part *parts[];
 		};
 		/*
 		 * This little trick makes sure that
-- 
GitLab


From b62e408c05228f40e69bb38a48db8961cac6cd23 Mon Sep 17 00:00:00 2001
From: David Rientjes <rientjes@google.com>
Date: Wed, 26 Aug 2009 14:29:22 -0700
Subject: [PATCH 1072/1153] flex_array: convert element_nr formals to unsigned

It's problematic to allow signed element_nr's or total's to be passed as
part of the flex array API.

flex_array_alloc() allows total_nr_elements to be set to a negative
quantity, which is obviously erroneous.

flex_array_get() and flex_array_put() allows negative array indices in
dereferencing an array part, which could address memory mapped before
struct flex_array.

The fix is to convert all existing element_nr formals to be qualified as
unsigned.  Existing checks to compare it to total_nr_elements or the max
array size based on element_size need not be changed.

Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/flex_array.h | 10 ++++++----
 lib/flex_array.c           | 24 +++++++++++++-----------
 2 files changed, 19 insertions(+), 15 deletions(-)

diff --git a/include/linux/flex_array.h b/include/linux/flex_array.h
index 603160db7c9..45ff1849151 100644
--- a/include/linux/flex_array.h
+++ b/include/linux/flex_array.h
@@ -36,12 +36,14 @@ struct flex_array {
 	.total_nr_elements = (total),	\
 } } }
 
-struct flex_array *flex_array_alloc(int element_size, int total, gfp_t flags);
-int flex_array_prealloc(struct flex_array *fa, int start, int end, gfp_t flags);
+struct flex_array *flex_array_alloc(int element_size, unsigned int total,
+		gfp_t flags);
+int flex_array_prealloc(struct flex_array *fa, unsigned int start,
+		unsigned int end, gfp_t flags);
 void flex_array_free(struct flex_array *fa);
 void flex_array_free_parts(struct flex_array *fa);
-int flex_array_put(struct flex_array *fa, int element_nr, void *src,
+int flex_array_put(struct flex_array *fa, unsigned int element_nr, void *src,
 		gfp_t flags);
-void *flex_array_get(struct flex_array *fa, int element_nr);
+void *flex_array_get(struct flex_array *fa, unsigned int element_nr);
 
 #endif /* _FLEX_ARRAY_H */
diff --git a/lib/flex_array.c b/lib/flex_array.c
index cf4e372cae9..7baed2fc3bc 100644
--- a/lib/flex_array.c
+++ b/lib/flex_array.c
@@ -99,7 +99,8 @@ static inline int elements_fit_in_base(struct flex_array *fa)
  * capacity in the base structure.  Also note that no effort is made
  * to efficiently pack objects across page boundaries.
  */
-struct flex_array *flex_array_alloc(int element_size, int total, gfp_t flags)
+struct flex_array *flex_array_alloc(int element_size, unsigned int total,
+					gfp_t flags)
 {
 	struct flex_array *ret;
 	int max_size = nr_base_part_ptrs() * __elements_per_part(element_size);
@@ -115,7 +116,8 @@ struct flex_array *flex_array_alloc(int element_size, int total, gfp_t flags)
 	return ret;
 }
 
-static int fa_element_to_part_nr(struct flex_array *fa, int element_nr)
+static int fa_element_to_part_nr(struct flex_array *fa,
+					unsigned int element_nr)
 {
 	return element_nr / __elements_per_part(fa->element_size);
 }
@@ -143,14 +145,12 @@ void flex_array_free(struct flex_array *fa)
 	kfree(fa);
 }
 
-static int fa_index_inside_part(struct flex_array *fa, int element_nr)
+static unsigned int index_inside_part(struct flex_array *fa,
+					unsigned int element_nr)
 {
-	return element_nr % __elements_per_part(fa->element_size);
-}
+	unsigned int part_offset;
 
-static int index_inside_part(struct flex_array *fa, int element_nr)
-{
-	int part_offset = fa_index_inside_part(fa, element_nr);
+	part_offset = element_nr % __elements_per_part(fa->element_size);
 	return part_offset * fa->element_size;
 }
 
@@ -185,7 +185,8 @@ __fa_get_part(struct flex_array *fa, int part_nr, gfp_t flags)
  *
  * Locking must be provided by the caller.
  */
-int flex_array_put(struct flex_array *fa, int element_nr, void *src, gfp_t flags)
+int flex_array_put(struct flex_array *fa, unsigned int element_nr, void *src,
+			gfp_t flags)
 {
 	int part_nr = fa_element_to_part_nr(fa, element_nr);
 	struct flex_array_part *part;
@@ -217,7 +218,8 @@ int flex_array_put(struct flex_array *fa, int element_nr, void *src, gfp_t flags
  *
  * Locking must be provided by the caller.
  */
-int flex_array_prealloc(struct flex_array *fa, int start, int end, gfp_t flags)
+int flex_array_prealloc(struct flex_array *fa, unsigned int start,
+			unsigned int end, gfp_t flags)
 {
 	int start_part;
 	int end_part;
@@ -248,7 +250,7 @@ int flex_array_prealloc(struct flex_array *fa, int start, int end, gfp_t flags)
  *
  * Locking must be provided by the caller.
  */
-void *flex_array_get(struct flex_array *fa, int element_nr)
+void *flex_array_get(struct flex_array *fa, unsigned int element_nr)
 {
 	int part_nr = fa_element_to_part_nr(fa, element_nr);
 	struct flex_array_part *part;
-- 
GitLab


From 03ef83af528899aa339e42d8024b37e2f434fba4 Mon Sep 17 00:00:00 2001
From: Minchan Kim <minchan.kim@gmail.com>
Date: Wed, 26 Aug 2009 14:29:23 -0700
Subject: [PATCH 1073/1153] mm: fix for infinite churning of mlocked pages

An mlocked page might lose the isolatation race.  This causes the page to
clear PG_mlocked while it remains in a VM_LOCKED vma.  This means it can
be put onto the [in]active list.  We can rescue it by using try_to_unmap()
in shrink_page_list().

But now, As Wu Fengguang pointed out, vmscan has a bug.  If the page has
PG_referenced, it can't reach try_to_unmap() in shrink_page_list() but is
put into the active list.  If the page is referenced repeatedly, it can
remain on the [in]active list without being moving to the unevictable
list.

This patch fixes it.

Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: KOSAKI Motohiro <<kosaki.motohiro@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 mm/rmap.c   | 1 +
 mm/vmscan.c | 9 +++++++--
 2 files changed, 8 insertions(+), 2 deletions(-)

diff --git a/mm/rmap.c b/mm/rmap.c
index 836c6c63e1f..0895b5c7cbf 100644
--- a/mm/rmap.c
+++ b/mm/rmap.c
@@ -358,6 +358,7 @@ static int page_referenced_one(struct page *page,
 	 */
 	if (vma->vm_flags & VM_LOCKED) {
 		*mapcount = 1;	/* break early from loop */
+		*vm_flags |= VM_LOCKED;
 		goto out_unmap;
 	}
 
diff --git a/mm/vmscan.c b/mm/vmscan.c
index dea7abd3109..94e86dd6954 100644
--- a/mm/vmscan.c
+++ b/mm/vmscan.c
@@ -630,9 +630,14 @@ static unsigned long shrink_page_list(struct list_head *page_list,
 
 		referenced = page_referenced(page, 1,
 						sc->mem_cgroup, &vm_flags);
-		/* In active use or really unfreeable?  Activate it. */
+		/*
+		 * In active use or really unfreeable?  Activate it.
+		 * If page which have PG_mlocked lost isoltation race,
+		 * try_to_unmap moves it to unevictable list
+		 */
 		if (sc->order <= PAGE_ALLOC_COSTLY_ORDER &&
-					referenced && page_mapping_inuse(page))
+					referenced && page_mapping_inuse(page)
+					&& !(vm_flags & VM_LOCKED))
 			goto activate_locked;
 
 		/*
-- 
GitLab


From 4ab6c08336535f8c8e42cf45d7adeda882eff06e Mon Sep 17 00:00:00 2001
From: Oleg Nesterov <oleg@redhat.com>
Date: Wed, 26 Aug 2009 14:29:24 -0700
Subject: [PATCH 1074/1153] clone(): fix race between copy_process() and
 de_thread()

Spotted by Hiroshi Shimamoto who also provided the test-case below.

copy_process() uses signal->count as a reference counter, but it is not.
This test case

	#include <sys/types.h>
	#include <sys/wait.h>
	#include <unistd.h>
	#include <stdio.h>
	#include <errno.h>
	#include <pthread.h>

	void *null_thread(void *p)
	{
		for (;;)
			sleep(1);

		return NULL;
	}

	void *exec_thread(void *p)
	{
		execl("/bin/true", "/bin/true", NULL);

		return null_thread(p);
	}

	int main(int argc, char **argv)
	{
		for (;;) {
			pid_t pid;
			int ret, status;

			pid = fork();
			if (pid < 0)
				break;

			if (!pid) {
				pthread_t tid;

				pthread_create(&tid, NULL, exec_thread, NULL);
				for (;;)
					pthread_create(&tid, NULL, null_thread, NULL);
			}

			do {
				ret = waitpid(pid, &status, 0);
			} while (ret == -1 && errno == EINTR);
		}

		return 0;
	}

quickly creates an unkillable task.

If copy_process(CLONE_THREAD) races with de_thread()
copy_signal()->atomic(signal->count) breaks the signal->notify_count
logic, and the execing thread can hang forever in kernel space.

Change copy_process() to increment count/live only when we know for sure
we can't fail.  In this case the forked thread will take care of its
reference to signal correctly.

If copy_process() fails, check CLONE_THREAD flag.  If it it set - do
nothing, the counters were not changed and current belongs to the same
thread group.  If it is not set, ->signal must be released in any case
(and ->count must be == 1), the forked child is the only thread in the
thread group.

We need more cleanups here, in particular signal->count should not be used
by de_thread/__exit_signal at all.  This patch only fixes the bug.

Reported-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/fork.c | 20 +++++---------------
 1 file changed, 5 insertions(+), 15 deletions(-)

diff --git a/kernel/fork.c b/kernel/fork.c
index 144326b7af5..e6c04d462ab 100644
--- a/kernel/fork.c
+++ b/kernel/fork.c
@@ -815,11 +815,8 @@ static int copy_signal(unsigned long clone_flags, struct task_struct *tsk)
 {
 	struct signal_struct *sig;
 
-	if (clone_flags & CLONE_THREAD) {
-		atomic_inc(&current->signal->count);
-		atomic_inc(&current->signal->live);
+	if (clone_flags & CLONE_THREAD)
 		return 0;
-	}
 
 	sig = kmem_cache_alloc(signal_cachep, GFP_KERNEL);
 	tsk->signal = sig;
@@ -877,16 +874,6 @@ void __cleanup_signal(struct signal_struct *sig)
 	kmem_cache_free(signal_cachep, sig);
 }
 
-static void cleanup_signal(struct task_struct *tsk)
-{
-	struct signal_struct *sig = tsk->signal;
-
-	atomic_dec(&sig->live);
-
-	if (atomic_dec_and_test(&sig->count))
-		__cleanup_signal(sig);
-}
-
 static void copy_flags(unsigned long clone_flags, struct task_struct *p)
 {
 	unsigned long new_flags = p->flags;
@@ -1239,6 +1226,8 @@ static struct task_struct *copy_process(unsigned long clone_flags,
 	}
 
 	if (clone_flags & CLONE_THREAD) {
+		atomic_inc(&current->signal->count);
+		atomic_inc(&current->signal->live);
 		p->group_leader = current->group_leader;
 		list_add_tail_rcu(&p->thread_group, &p->group_leader->thread_group);
 	}
@@ -1282,7 +1271,8 @@ bad_fork_cleanup_mm:
 	if (p->mm)
 		mmput(p->mm);
 bad_fork_cleanup_signal:
-	cleanup_signal(p);
+	if (!(clone_flags & CLONE_THREAD))
+		__cleanup_signal(p->signal);
 bad_fork_cleanup_sighand:
 	__cleanup_sighand(p->sighand);
 bad_fork_cleanup_fs:
-- 
GitLab


From 0d288162f2afc42b37aab656f4622c076babbca3 Mon Sep 17 00:00:00 2001
From: Michael Brunner <mibru@gmx.de>
Date: Wed, 26 Aug 2009 14:29:25 -0700
Subject: [PATCH 1075/1153] thermal_sys: check get_temp return value

The return value of the get_temp function is not checked when doing a
thermal zone update.  This may lead to a critical shutdown if get_temp
fails and the content of the temp variable is incorrectly set higher than
the critical trip point.

This has been observed on a system with incorrect ACPI implementation
where the corresponding methods were not serialized and therefore
sometimes triggered ACPI errors (AE_ALREADY_EXISTS).  The following
critical shutdowns indicated a temperature of 2097 C, which was obviously
wrong.

The patch adds a return value check that jumps over all trip point
evaluations printing a warning if get_temp fails.  The trip points are
evaluated again on the next polling interval with successful get_temp
execution.

Signed-off-by: Michael Brunner <mibru@gmx.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/thermal/thermal_sys.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/thermal/thermal_sys.c b/drivers/thermal/thermal_sys.c
index 0a69672097a..4e83c297ec9 100644
--- a/drivers/thermal/thermal_sys.c
+++ b/drivers/thermal/thermal_sys.c
@@ -953,7 +953,12 @@ void thermal_zone_device_update(struct thermal_zone_device *tz)
 
 	mutex_lock(&tz->lock);
 
-	tz->ops->get_temp(tz, &temp);
+	if (tz->ops->get_temp(tz, &temp)) {
+		/* get_temp failed - retry it later */
+		printk(KERN_WARNING PREFIX "failed to read out thermal zone "
+		       "%d\n", tz->id);
+		goto leave;
+	}
 
 	for (count = 0; count < tz->trips; count++) {
 		tz->ops->get_trip_type(tz, count, &trip_type);
@@ -1005,6 +1010,8 @@ void thermal_zone_device_update(struct thermal_zone_device *tz)
 					    THERMAL_TRIPS_NONE);
 
 	tz->last_temperature = temp;
+
+      leave:
 	if (tz->passive)
 		thermal_zone_device_set_polling(tz, tz->passive_delay);
 	else if (tz->polling_delay)
-- 
GitLab


From ce8442b55135c679809311997d1446f3bbc05de2 Mon Sep 17 00:00:00 2001
From: Yinghai Lu <yinghai@kernel.org>
Date: Wed, 26 Aug 2009 14:29:26 -0700
Subject: [PATCH 1076/1153] acpi: don't call acpi_processor_init if acpi is
 disabled

Jens reported early_ioremap messages with old ASUS board...

> [    1.507461] pci 0000:00:09.0: Firmware left e100 interrupts enabled; disabling
> [    1.532778] early_ioremap(3fffd080, 0000005c) [0] => Pid: 1, comm: swapper Not tainted 2.6.31-rc4 #36
> [    1.561007] Call Trace:
> [    1.568638]  [<c136e48b>] ? printk+0x18/0x1d
> [    1.581734]  [<c15513ff>] __early_ioremap+0x74/0x1e9
> [    1.596898]  [<c15515aa>] early_ioremap+0x1a/0x1c
> [    1.611270]  [<c154a187>] __acpi_map_table+0x18/0x1a
> [    1.626451]  [<c135a7f8>] acpi_os_map_memory+0x1d/0x25
> [    1.642129]  [<c119459c>] acpi_tb_verify_table+0x20/0x49
> [    1.658321]  [<c1193e50>] acpi_get_table_with_size+0x53/0xa1
> [    1.675553]  [<c1193eae>] acpi_get_table+0x10/0x15
> [    1.690192]  [<c155cc19>] acpi_processor_init+0x23/0xab
> [    1.706126]  [<c1001043>] do_one_initcall+0x33/0x180
> [    1.721279]  [<c155cbf6>] ? acpi_processor_init+0x0/0xab
> [    1.737479]  [<c106893a>] ? register_irq_proc+0xaa/0xc0
> [    1.753411]  [<c10689b7>] ? init_irq_proc+0x67/0x80
> [    1.768316]  [<c15405e7>] kernel_init+0x120/0x176
> [    1.782678]  [<c15404c7>] ? kernel_init+0x0/0x176
> [    1.797062]  [<c10038b7>] kernel_thread_helper+0x7/0x10
> [    1.812984] 00000080 + ffe00000

that is rather later.
acpi_gbl_permanent_mmap should be set in acpi_early_init()
if acpi is not disabled

and we have
> [    0.000000] ASUS P2B-DS detected: force use of acpi=ht

just don't load acpi_processor_init...

Reported-and-tested-by: Jens Rosenboom <jens@leia.mcbone.net>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/acpi/processor_core.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/acpi/processor_core.c b/drivers/acpi/processor_core.c
index 84e0f3c0744..2cc4b303387 100644
--- a/drivers/acpi/processor_core.c
+++ b/drivers/acpi/processor_core.c
@@ -1151,6 +1151,9 @@ static int __init acpi_processor_init(void)
 {
 	int result = 0;
 
+	if (acpi_disabled)
+		return 0;
+
 	memset(&errata, 0, sizeof(errata));
 
 #ifdef CONFIG_SMP
@@ -1197,6 +1200,9 @@ out_proc:
 
 static void __exit acpi_processor_exit(void)
 {
+	if (acpi_disabled)
+		return;
+
 	acpi_processor_ppc_exit();
 
 	acpi_thermal_cpufreq_exit();
-- 
GitLab


From f3d83e2415445e5b157bef404d38674e9e8de169 Mon Sep 17 00:00:00 2001
From: Costantino Leandro <lcostantino@gmail.com>
Date: Wed, 26 Aug 2009 14:29:28 -0700
Subject: [PATCH 1077/1153] wmi: fix kernel panic when stack protection
 enabled.

Summary:
Kernel panic arise when stack protection is enabled, since strncat will
add a null terminating byte '\0'; So in functions
like this one (wmi_query_block):
        char wc[4]="WC";
	....
	strncat(method, block->object_id, 2);
        ...
the length of wc should be n+1 (wc[5]) or stack protection
fault will arise. This is not noticeable when stack protection is
disabled,but , isn't good either.
Config used: [CONFIG_CC_STACKPROTECTOR_ALL=y,
	      CONFIG_CC_STACKPROTECTOR=y]

Panic Trace
------------
       .... stack-protector: kernel stack corrupted in : fa7b182c
       2.6.30-rc8-obelisco-generic
       call_trace:
           [<c04a6c40>] ? panic+0x45/0xd9
	   [<c012925d>] ? __stack_chk_fail+0x1c/0x40
	   [<fa7b182c>] ? wmi_query_block+0x15a/0x162 [wmi]
	   [<fa7b182c>] ? wmi_query_block+0x15a/0x162 [wmi]
	   [<fa7e7000>] ? acer_wmi_init+0x00/0x61a [acer_wmi]
	   [<fa7e7135>] ? acer_wmi_init+0x135/0x61a [acer_wmi]
	   [<c0101159>] ? do_one_initcall+0x50+0x126

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13514

Signed-off-by: Costantino Leandro <lcostantino@gmail.com>
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/platform/x86/wmi.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/platform/x86/wmi.c b/drivers/platform/x86/wmi.c
index 043b208d971..f215a591919 100644
--- a/drivers/platform/x86/wmi.c
+++ b/drivers/platform/x86/wmi.c
@@ -270,7 +270,7 @@ u32 method_id, const struct acpi_buffer *in, struct acpi_buffer *out)
 	acpi_status status;
 	struct acpi_object_list input;
 	union acpi_object params[3];
-	char method[4] = "WM";
+	char method[5] = "WM";
 
 	if (!find_guid(guid_string, &wblock))
 		return AE_ERROR;
@@ -328,8 +328,8 @@ struct acpi_buffer *out)
 	acpi_status status, wc_status = AE_ERROR;
 	struct acpi_object_list input, wc_input;
 	union acpi_object wc_params[1], wq_params[1];
-	char method[4];
-	char wc_method[4] = "WC";
+	char method[5];
+	char wc_method[5] = "WC";
 
 	if (!guid_string || !out)
 		return AE_BAD_PARAMETER;
@@ -410,7 +410,7 @@ const struct acpi_buffer *in)
 	acpi_handle handle;
 	struct acpi_object_list input;
 	union acpi_object params[2];
-	char method[4] = "WS";
+	char method[5] = "WS";
 
 	if (!guid_string || !in)
 		return AE_BAD_DATA;
-- 
GitLab


From 2a908002c7b1b666616103e9df2419b38d7c6f1f Mon Sep 17 00:00:00 2001
From: Frans Pop <elendil@planet.nl>
Date: Wed, 26 Aug 2009 14:29:29 -0700
Subject: [PATCH 1078/1153] ACPI processor: force throttling state when BIOS
 returns incorrect value

If the BIOS reports an invalid throttling state (which seems to be
fairly common after system boot), a reset is done to state T0.
Because of a check in acpi_processor_get_throttling_ptc(), the reset
never actually gets executed, which results in the error reoccurring
on every access of for example /proc/acpi/processor/CPU0/throttling.

Add a 'force' option to acpi_processor_set_throttling() to ensure
the reset really takes effect.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389

This patch, together with the next one, fixes a regression introduced in
2.6.30, listed on the regression list. They have been available for 2.5
months now in bugzilla, but have not been picked up, despite various
reminders and without any reason given.

Google shows that numerous people are hitting this issue. The issue is in
itself relatively minor, but the bug in the code is clear.

The patches have been in all my kernels and today testing has shown that
throttling works correctly with the patches applied when the system
overheats (http://bugzilla.kernel.org/show_bug.cgi?id=13918#c14).

Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/acpi/processor_thermal.c    |  6 +++---
 drivers/acpi/processor_throttling.c | 26 ++++++++++++++------------
 include/acpi/processor.h            |  5 +++--
 3 files changed, 20 insertions(+), 17 deletions(-)

diff --git a/drivers/acpi/processor_thermal.c b/drivers/acpi/processor_thermal.c
index 39838c66603..31adda1099e 100644
--- a/drivers/acpi/processor_thermal.c
+++ b/drivers/acpi/processor_thermal.c
@@ -66,7 +66,7 @@ static int acpi_processor_apply_limit(struct acpi_processor *pr)
 		if (pr->limit.thermal.tx > tx)
 			tx = pr->limit.thermal.tx;
 
-		result = acpi_processor_set_throttling(pr, tx);
+		result = acpi_processor_set_throttling(pr, tx, false);
 		if (result)
 			goto end;
 	}
@@ -421,12 +421,12 @@ processor_set_cur_state(struct thermal_cooling_device *cdev,
 
 	if (state <= max_pstate) {
 		if (pr->flags.throttling && pr->throttling.state)
-			result = acpi_processor_set_throttling(pr, 0);
+			result = acpi_processor_set_throttling(pr, 0, false);
 		cpufreq_set_cur_state(pr->id, state);
 	} else {
 		cpufreq_set_cur_state(pr->id, max_pstate);
 		result = acpi_processor_set_throttling(pr,
-				state - max_pstate);
+				state - max_pstate, false);
 	}
 	return result;
 }
diff --git a/drivers/acpi/processor_throttling.c b/drivers/acpi/processor_throttling.c
index 227543789ba..841be4ee210 100644
--- a/drivers/acpi/processor_throttling.c
+++ b/drivers/acpi/processor_throttling.c
@@ -62,7 +62,8 @@ struct throttling_tstate {
 #define THROTTLING_POSTCHANGE      (2)
 
 static int acpi_processor_get_throttling(struct acpi_processor *pr);
-int acpi_processor_set_throttling(struct acpi_processor *pr, int state);
+int acpi_processor_set_throttling(struct acpi_processor *pr,
+						int state, bool force);
 
 static int acpi_processor_update_tsd_coord(void)
 {
@@ -361,7 +362,7 @@ int acpi_processor_tstate_has_changed(struct acpi_processor *pr)
 		 */
 		target_state = throttling_limit;
 	}
-	return acpi_processor_set_throttling(pr, target_state);
+	return acpi_processor_set_throttling(pr, target_state, false);
 }
 
 /*
@@ -842,7 +843,7 @@ static int acpi_processor_get_throttling_ptc(struct acpi_processor *pr)
 			ACPI_WARNING((AE_INFO,
 				"Invalid throttling state, reset"));
 			state = 0;
-			ret = acpi_processor_set_throttling(pr, state);
+			ret = acpi_processor_set_throttling(pr, state, true);
 			if (ret)
 				return ret;
 		}
@@ -915,7 +916,7 @@ static int acpi_processor_get_fadt_info(struct acpi_processor *pr)
 }
 
 static int acpi_processor_set_throttling_fadt(struct acpi_processor *pr,
-					      int state)
+					      int state, bool force)
 {
 	u32 value = 0;
 	u32 duty_mask = 0;
@@ -930,7 +931,7 @@ static int acpi_processor_set_throttling_fadt(struct acpi_processor *pr,
 	if (!pr->flags.throttling)
 		return -ENODEV;
 
-	if (state == pr->throttling.state)
+	if (!force && (state == pr->throttling.state))
 		return 0;
 
 	if (state < pr->throttling_platform_limit)
@@ -988,7 +989,7 @@ static int acpi_processor_set_throttling_fadt(struct acpi_processor *pr,
 }
 
 static int acpi_processor_set_throttling_ptc(struct acpi_processor *pr,
-					     int state)
+					     int state, bool force)
 {
 	int ret;
 	acpi_integer value;
@@ -1002,7 +1003,7 @@ static int acpi_processor_set_throttling_ptc(struct acpi_processor *pr,
 	if (!pr->flags.throttling)
 		return -ENODEV;
 
-	if (state == pr->throttling.state)
+	if (!force && (state == pr->throttling.state))
 		return 0;
 
 	if (state < pr->throttling_platform_limit)
@@ -1018,7 +1019,8 @@ static int acpi_processor_set_throttling_ptc(struct acpi_processor *pr,
 	return 0;
 }
 
-int acpi_processor_set_throttling(struct acpi_processor *pr, int state)
+int acpi_processor_set_throttling(struct acpi_processor *pr,
+						int state, bool force)
 {
 	cpumask_var_t saved_mask;
 	int ret = 0;
@@ -1070,7 +1072,7 @@ int acpi_processor_set_throttling(struct acpi_processor *pr, int state)
 		/* FIXME: use work_on_cpu() */
 		set_cpus_allowed_ptr(current, cpumask_of(pr->id));
 		ret = p_throttling->acpi_processor_set_throttling(pr,
-						t_state.target_state);
+						t_state.target_state, force);
 	} else {
 		/*
 		 * When the T-state coordination is SW_ALL or HW_ALL,
@@ -1103,7 +1105,7 @@ int acpi_processor_set_throttling(struct acpi_processor *pr, int state)
 			set_cpus_allowed_ptr(current, cpumask_of(i));
 			ret = match_pr->throttling.
 				acpi_processor_set_throttling(
-				match_pr, t_state.target_state);
+				match_pr, t_state.target_state, force);
 		}
 	}
 	/*
@@ -1201,7 +1203,7 @@ int acpi_processor_get_throttling_info(struct acpi_processor *pr)
 		ACPI_DEBUG_PRINT((ACPI_DB_INFO,
 				  "Disabling throttling (was T%d)\n",
 				  pr->throttling.state));
-		result = acpi_processor_set_throttling(pr, 0);
+		result = acpi_processor_set_throttling(pr, 0, false);
 		if (result)
 			goto end;
 	}
@@ -1307,7 +1309,7 @@ static ssize_t acpi_processor_write_throttling(struct file *file,
 	if (strcmp(tmpbuf, charp) != 0)
 		return -EINVAL;
 
-	result = acpi_processor_set_throttling(pr, state_val);
+	result = acpi_processor_set_throttling(pr, state_val, false);
 	if (result)
 		return result;
 
diff --git a/include/acpi/processor.h b/include/acpi/processor.h
index baf1e0a9a7e..740ac3ad8fd 100644
--- a/include/acpi/processor.h
+++ b/include/acpi/processor.h
@@ -174,7 +174,7 @@ struct acpi_processor_throttling {
 	cpumask_var_t shared_cpu_map;
 	int (*acpi_processor_get_throttling) (struct acpi_processor * pr);
 	int (*acpi_processor_set_throttling) (struct acpi_processor * pr,
-					      int state);
+					      int state, bool force);
 
 	u32 address;
 	u8 duty_offset;
@@ -321,7 +321,8 @@ static inline int acpi_processor_ppc_has_changed(struct acpi_processor *pr)
 /* in processor_throttling.c */
 int acpi_processor_tstate_has_changed(struct acpi_processor *pr);
 int acpi_processor_get_throttling_info(struct acpi_processor *pr);
-extern int acpi_processor_set_throttling(struct acpi_processor *pr, int state);
+extern int acpi_processor_set_throttling(struct acpi_processor *pr,
+					 int state, bool force);
 extern const struct file_operations acpi_processor_throttling_fops;
 extern void acpi_processor_throttling_init(void);
 /* in processor_idle.c */
-- 
GitLab


From bdf57de4e6abc389cc3f3bd94ec15cce74cf6f4b Mon Sep 17 00:00:00 2001
From: Frans Pop <elendil@planet.nl>
Date: Wed, 26 Aug 2009 14:29:30 -0700
Subject: [PATCH 1079/1153] acpi processor: remove superfluous warning message

This failure is very common on many platforms.  Handling it in the ACPI
processor driver is enough, and we don't need a warning message unless
CONFIG_ACPI_DEBUG is set.

Based on a patch from Zhang Rui.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389

Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/acpi/processor_throttling.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/acpi/processor_throttling.c b/drivers/acpi/processor_throttling.c
index 841be4ee210..ae39797aab5 100644
--- a/drivers/acpi/processor_throttling.c
+++ b/drivers/acpi/processor_throttling.c
@@ -840,8 +840,8 @@ static int acpi_processor_get_throttling_ptc(struct acpi_processor *pr)
 	if (ret >= 0) {
 		state = acpi_get_throttling_state(pr, value);
 		if (state == -1) {
-			ACPI_WARNING((AE_INFO,
-				"Invalid throttling state, reset"));
+			ACPI_DEBUG_PRINT((ACPI_DB_INFO,
+				"Invalid throttling state, reset\n"));
 			state = 0;
 			ret = acpi_processor_set_throttling(pr, state, true);
 			if (ret)
-- 
GitLab


From 48cccd26f36511ddb6aeca07485ecf2829683907 Mon Sep 17 00:00:00 2001
From: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Date: Wed, 26 Aug 2009 14:29:31 -0700
Subject: [PATCH 1080/1153] leds: fix multiple requests and releases of IRQ for
 GPIO LED Trigger

When setting the same GPIO number, multiple IRQ shared requests will be
done without freing the previous request.  It will also try to free a
failed request or an already freed IRQ if 0 was written to the gpio file.

All these oops and leaks were fixed with the following solution: keep the
previous allocated GPIO (if any) still allocated in case the new request
fails.  The alternative solution would desallocate the previous allocated
GPIO and set gpio as 0.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/leds/ledtrig-gpio.c | 21 ++++++++++++++-------
 1 file changed, 14 insertions(+), 7 deletions(-)

diff --git a/drivers/leds/ledtrig-gpio.c b/drivers/leds/ledtrig-gpio.c
index a247ae63374..8183b81fca8 100644
--- a/drivers/leds/ledtrig-gpio.c
+++ b/drivers/leds/ledtrig-gpio.c
@@ -146,20 +146,26 @@ static ssize_t gpio_trig_gpio_store(struct device *dev,
 		return -EINVAL;
 	}
 
+	if (gpio_data->gpio == gpio)
+		return n;
+
 	if (!gpio) {
-		free_irq(gpio_to_irq(gpio_data->gpio), led);
+		if (gpio_data->gpio != 0)
+			free_irq(gpio_to_irq(gpio_data->gpio), led);
+		gpio_data->gpio = 0;
 		return n;
 	}
 
-	if (gpio_data->gpio > 0 && gpio_data->gpio != gpio)
-		free_irq(gpio_to_irq(gpio_data->gpio), led);
-
-	gpio_data->gpio = gpio;
 	ret = request_irq(gpio_to_irq(gpio), gpio_trig_irq,
 			IRQF_SHARED | IRQF_TRIGGER_RISING
 			| IRQF_TRIGGER_FALLING, "ledtrig-gpio", led);
-	if (ret)
+	if (ret) {
 		dev_err(dev, "request_irq failed with error %d\n", ret);
+	} else {
+		if (gpio_data->gpio != 0)
+			free_irq(gpio_to_irq(gpio_data->gpio), led);
+		gpio_data->gpio = gpio;
+	}
 
 	return ret ? ret : n;
 }
@@ -211,7 +217,8 @@ static void gpio_trig_deactivate(struct led_classdev *led)
 		device_remove_file(led->dev, &dev_attr_inverted);
 		device_remove_file(led->dev, &dev_attr_desired_brightness);
 		flush_work(&gpio_data->work);
-		free_irq(gpio_to_irq(gpio_data->gpio),led);
+		if (gpio_data->gpio != 0)
+			free_irq(gpio_to_irq(gpio_data->gpio), led);
 		kfree(gpio_data);
 	}
 }
-- 
GitLab


From cc674c81f01a6151ca00c617e5efa0812ee5fdbe Mon Sep 17 00:00:00 2001
From: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Date: Wed, 26 Aug 2009 14:29:32 -0700
Subject: [PATCH 1081/1153] leds: after setting inverted attribute, we must
 update the LED

If we change the inverted attribute to another value, the LED will not be
inverted until we change the GPIO state.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/leds/ledtrig-gpio.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/leds/ledtrig-gpio.c b/drivers/leds/ledtrig-gpio.c
index 8183b81fca8..1bc5db4ece0 100644
--- a/drivers/leds/ledtrig-gpio.c
+++ b/drivers/leds/ledtrig-gpio.c
@@ -117,6 +117,9 @@ static ssize_t gpio_trig_inverted_store(struct device *dev,
 
 	gpio_data->inverted = !!inverted;
 
+	/* After inverting, we need to update the LED. */
+	schedule_work(&gpio_data->work);
+
 	return n;
 }
 static DEVICE_ATTR(inverted, 0644, gpio_trig_inverted_show,
-- 
GitLab


From 7b6a09f3d6aedeaac923824af2a5df30300b56e9 Mon Sep 17 00:00:00 2001
From: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Date: Sun, 23 Aug 2009 22:54:32 +0000
Subject: [PATCH 1082/1153] powerpc/ps3: Add missing check for PS3 to rtc-ps3
 platform device registration

On non-PS3, we get:

| kernel BUG at drivers/rtc/rtc-ps3.c:36!

because the rtc-ps3 platform device is registered unconditionally in a kernel
with builtin support for PS3.

Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/platforms/ps3/time.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/powerpc/platforms/ps3/time.c b/arch/powerpc/platforms/ps3/time.c
index b178a1e66c9..40b5cb43300 100644
--- a/arch/powerpc/platforms/ps3/time.c
+++ b/arch/powerpc/platforms/ps3/time.c
@@ -21,6 +21,7 @@
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 
+#include <asm/firmware.h>
 #include <asm/rtc.h>
 #include <asm/lv1call.h>
 #include <asm/ps3.h>
@@ -84,6 +85,9 @@ static int __init ps3_rtc_init(void)
 {
 	struct platform_device *pdev;
 
+	if (!firmware_has_feature(FW_FEATURE_PS3_LV1))
+		return -ENODEV;
+
 	pdev = platform_device_register_simple("rtc-ps3", -1, NULL, 0);
 	if (IS_ERR(pdev))
 		return PTR_ERR(pdev);
-- 
GitLab


From b080f187adb79bbcbe28814b07cbc1ead34c469a Mon Sep 17 00:00:00 2001
From: Geoff Levand <geoffrey.levand@am.sony.com>
Date: Tue, 25 Aug 2009 07:53:35 +0000
Subject: [PATCH 1083/1153] powerpc/ps3: Update ps3_defconfig

Update ps3_defconfig.

 o Refresh for 2.6.31.
 o Remove MTD support.
 o Add more HID drivers.

Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
 arch/powerpc/configs/ps3_defconfig | 211 ++++++++++-------------------
 1 file changed, 75 insertions(+), 136 deletions(-)

diff --git a/arch/powerpc/configs/ps3_defconfig b/arch/powerpc/configs/ps3_defconfig
index e28e65e7a0e..7de127e4cee 100644
--- a/arch/powerpc/configs/ps3_defconfig
+++ b/arch/powerpc/configs/ps3_defconfig
@@ -1,13 +1,14 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc5
-# Fri May 15 10:37:00 2009
+# Linux kernel version: 2.6.31-rc7
+# Mon Aug 24 17:38:50 2009
 #
 CONFIG_PPC64=y
 
 #
 # Processor support
 #
+CONFIG_PPC_BOOK3S_64=y
 CONFIG_PPC_BOOK3S=y
 # CONFIG_POWER4_ONLY is not set
 CONFIG_POWER3=y
@@ -20,6 +21,7 @@ CONFIG_PPC_STD_MMU=y
 CONFIG_PPC_STD_MMU_64=y
 CONFIG_PPC_MM_SLICES=y
 CONFIG_VIRT_CPU_ACCOUNTING=y
+CONFIG_PPC_HAVE_PMU_SUPPORT=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_64BIT=y
@@ -31,6 +33,7 @@ CONFIG_GENERIC_TIME=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
 CONFIG_HAVE_SETUP_PER_CPU_AREA=y
 CONFIG_IRQ_PER_CPU=y
 CONFIG_STACKTRACE_SUPPORT=y
@@ -41,7 +44,6 @@ CONFIG_RWSEM_XCHGADD_ALGORITHM=y
 CONFIG_ARCH_HAS_ILOG2_U32=y
 CONFIG_ARCH_HAS_ILOG2_U64=y
 CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
 CONFIG_GENERIC_FIND_NEXT_BIT=y
 CONFIG_ARCH_NO_VIRT_TO_BUS=y
 CONFIG_PPC=y
@@ -62,6 +64,7 @@ CONFIG_DTC=y
 # CONFIG_PPC_DCR_MMIO is not set
 CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
 
 #
 # General setup
@@ -113,7 +116,6 @@ CONFIG_SYSCTL_SYSCALL=y
 CONFIG_KALLSYMS=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-# CONFIG_STRIP_ASM_SYMS is not set
 CONFIG_HOTPLUG=y
 CONFIG_PRINTK=y
 CONFIG_BUG=y
@@ -126,7 +128,14 @@ CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_AIO=y
+CONFIG_HAVE_PERF_COUNTERS=y
+
+#
+# Performance Counters
+#
+# CONFIG_PERF_COUNTERS is not set
 CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
 # CONFIG_COMPAT_BRK is not set
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
@@ -145,6 +154,11 @@ CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
 CONFIG_HAVE_DMA_ATTRS=y
 CONFIG_USE_GENERIC_SMP_HELPERS=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
 # CONFIG_SLOW_WORK is not set
 # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
 CONFIG_SLABINFO=y
@@ -210,7 +224,7 @@ CONFIG_PPC_CELL=y
 #
 # Cell Broadband Engine options
 #
-CONFIG_SPU_FS=y
+CONFIG_SPU_FS=m
 CONFIG_SPU_FS_64K_LS=y
 # CONFIG_SPU_TRACE is not set
 CONFIG_SPU_BASE=y
@@ -255,6 +269,7 @@ CONFIG_BINFMT_MISC=y
 CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y
 # CONFIG_IOMMU_VMERGE is not set
 CONFIG_IOMMU_HELPER=y
+# CONFIG_SWIOTLB is not set
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 CONFIG_ARCH_HAS_WALK_MEMORY=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
@@ -285,9 +300,9 @@ CONFIG_MIGRATION=y
 CONFIG_PHYS_ADDR_T_64BIT=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
-CONFIG_UNEVICTABLE_LRU=y
 CONFIG_HAVE_MLOCK=y
 CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
 CONFIG_ARCH_MEMORY_PROBE=y
 CONFIG_PPC_HAS_HASH_64K=y
 CONFIG_PPC_4K_PAGES=y
@@ -399,6 +414,7 @@ CONFIG_IPV6_NDISC_NODETYPE=y
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
 # CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
 # CONFIG_NET_SCHED is not set
 # CONFIG_DCB is not set
 
@@ -433,11 +449,14 @@ CONFIG_BT_HCIBTUSB=m
 CONFIG_WIRELESS=y
 CONFIG_CFG80211=m
 # CONFIG_CFG80211_REG_DEBUG is not set
+# CONFIG_CFG80211_DEBUGFS is not set
 # CONFIG_WIRELESS_OLD_REGULATORY is not set
 CONFIG_WIRELESS_EXT=y
 # CONFIG_WIRELESS_EXT_SYSFS is not set
 # CONFIG_LIB80211 is not set
 CONFIG_MAC80211=m
+CONFIG_MAC80211_DEFAULT_PS=y
+CONFIG_MAC80211_DEFAULT_PS_VALUE=1
 
 #
 # Rate control algorithm selection
@@ -447,7 +466,6 @@ CONFIG_MAC80211_RC_PID=y
 CONFIG_MAC80211_RC_DEFAULT_PID=y
 # CONFIG_MAC80211_RC_DEFAULT_MINSTREL is not set
 CONFIG_MAC80211_RC_DEFAULT="pid"
-# CONFIG_MAC80211_MESH is not set
 # CONFIG_MAC80211_LEDS is not set
 # CONFIG_MAC80211_DEBUGFS is not set
 # CONFIG_MAC80211_DEBUG_MENU is not set
@@ -472,77 +490,7 @@ CONFIG_EXTRA_FIRMWARE=""
 # CONFIG_DEBUG_DEVRES is not set
 # CONFIG_SYS_HYPERVISOR is not set
 # CONFIG_CONNECTOR is not set
-CONFIG_MTD=y
-CONFIG_MTD_DEBUG=y
-CONFIG_MTD_DEBUG_VERBOSE=0
-# CONFIG_MTD_CONCAT is not set
-# CONFIG_MTD_PARTITIONS is not set
-# CONFIG_MTD_TESTS is not set
-
-#
-# User Modules And Translation Layers
-#
-# CONFIG_MTD_CHAR is not set
-CONFIG_MTD_BLKDEVS=y
-CONFIG_MTD_BLOCK=y
-# CONFIG_FTL is not set
-# CONFIG_NFTL is not set
-# CONFIG_INFTL is not set
-# CONFIG_RFD_FTL is not set
-# CONFIG_SSFDC is not set
-# CONFIG_MTD_OOPS is not set
-
-#
-# RAM/ROM/Flash chip drivers
-#
-# CONFIG_MTD_CFI is not set
-# CONFIG_MTD_JEDECPROBE is not set
-CONFIG_MTD_MAP_BANK_WIDTH_1=y
-CONFIG_MTD_MAP_BANK_WIDTH_2=y
-CONFIG_MTD_MAP_BANK_WIDTH_4=y
-# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
-# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
-# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
-CONFIG_MTD_CFI_I1=y
-CONFIG_MTD_CFI_I2=y
-# CONFIG_MTD_CFI_I4 is not set
-# CONFIG_MTD_CFI_I8 is not set
-# CONFIG_MTD_RAM is not set
-# CONFIG_MTD_ROM is not set
-# CONFIG_MTD_ABSENT is not set
-
-#
-# Mapping drivers for chip access
-#
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-# CONFIG_MTD_PLATRAM is not set
-
-#
-# Self-contained MTD device drivers
-#
-# CONFIG_MTD_SLRAM is not set
-# CONFIG_MTD_PHRAM is not set
-# CONFIG_MTD_MTDRAM is not set
-# CONFIG_MTD_BLOCK2MTD is not set
-
-#
-# Disk-On-Chip Device Drivers
-#
-# CONFIG_MTD_DOC2000 is not set
-# CONFIG_MTD_DOC2001 is not set
-# CONFIG_MTD_DOC2001PLUS is not set
-# CONFIG_MTD_NAND is not set
-# CONFIG_MTD_ONENAND is not set
-
-#
-# LPDDR flash memory drivers
-#
-# CONFIG_MTD_LPDDR is not set
-
-#
-# UBI - Unsorted block images
-#
-# CONFIG_MTD_UBI is not set
+# CONFIG_MTD is not set
 CONFIG_OF_DEVICE=y
 # CONFIG_PARPORT is not set
 CONFIG_BLK_DEV=y
@@ -590,10 +538,6 @@ CONFIG_BLK_DEV_SR=y
 # CONFIG_BLK_DEV_SR_VENDOR is not set
 CONFIG_CHR_DEV_SG=m
 # CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
 CONFIG_SCSI_MULTI_LUN=y
 # CONFIG_SCSI_CONSTANTS is not set
 # CONFIG_SCSI_LOGGING is not set
@@ -626,7 +570,6 @@ CONFIG_BLK_DEV_DM=m
 # CONFIG_DM_UEVENT is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
 # CONFIG_MACVLAN is not set
@@ -646,10 +589,11 @@ CONFIG_MII=m
 # CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
 # CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
 # CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
 CONFIG_NETDEV_1000=y
 CONFIG_GELIC_NET=y
 CONFIG_GELIC_WIRELESS=y
-CONFIG_GELIC_WIRELESS_OLD_PSK_INTERFACE=y
+# CONFIG_GELIC_WIRELESS_OLD_PSK_INTERFACE is not set
 # CONFIG_NETDEV_10000 is not set
 
 #
@@ -669,8 +613,7 @@ CONFIG_WLAN_80211=y
 # CONFIG_HOSTAP is not set
 # CONFIG_B43 is not set
 # CONFIG_B43LEGACY is not set
-CONFIG_ZD1211RW=m
-# CONFIG_ZD1211RW_DEBUG is not set
+# CONFIG_ZD1211RW is not set
 # CONFIG_RT2X00 is not set
 
 #
@@ -682,7 +625,7 @@ CONFIG_ZD1211RW=m
 #
 # CONFIG_USB_CATC is not set
 # CONFIG_USB_KAWETH is not set
-CONFIG_USB_PEGASUS=m
+# CONFIG_USB_PEGASUS is not set
 # CONFIG_USB_RTL8150 is not set
 CONFIG_USB_USBNET=m
 CONFIG_USB_NET_AX8817X=m
@@ -693,10 +636,11 @@ CONFIG_USB_NET_AX8817X=m
 # CONFIG_USB_NET_GL620A is not set
 # CONFIG_USB_NET_NET1080 is not set
 # CONFIG_USB_NET_PLUSB is not set
-CONFIG_USB_NET_MCS7830=m
+# CONFIG_USB_NET_MCS7830 is not set
 # CONFIG_USB_NET_RNDIS_HOST is not set
 # CONFIG_USB_NET_CDC_SUBSET is not set
 # CONFIG_USB_NET_ZAURUS is not set
+# CONFIG_USB_NET_INT51X1 is not set
 # CONFIG_WAN is not set
 CONFIG_PPP=m
 CONFIG_PPP_MULTILINK=y
@@ -771,8 +715,7 @@ CONFIG_DEVKMEM=y
 #
 CONFIG_UNIX98_PTYS=y
 # CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=16
+# CONFIG_LEGACY_PTYS is not set
 # CONFIG_HVC_UDBG is not set
 # CONFIG_IPMI_HANDLER is not set
 # CONFIG_HW_RANDOM is not set
@@ -782,6 +725,11 @@ CONFIG_LEGACY_PTY_COUNT=16
 # CONFIG_TCG_TPM is not set
 # CONFIG_I2C is not set
 # CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -805,22 +753,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_REGULATOR is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MEDIA_SUPPORT is not set
 
 #
 # Graphics support
@@ -898,6 +831,11 @@ CONFIG_SND_SUPPORT_OLD_API=y
 CONFIG_SND_VERBOSE_PROCFS=y
 # CONFIG_SND_VERBOSE_PRINTK is not set
 # CONFIG_SND_DEBUG is not set
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
 # CONFIG_SND_DRIVERS is not set
 CONFIG_SND_PPC=y
 CONFIG_SND_PS3=m
@@ -930,29 +868,34 @@ CONFIG_USB_HIDDEV=y
 # Special HID drivers
 #
 # CONFIG_HID_A4TECH is not set
-# CONFIG_HID_APPLE is not set
-# CONFIG_HID_BELKIN is not set
-# CONFIG_HID_CHERRY is not set
+CONFIG_HID_APPLE=m
+CONFIG_HID_BELKIN=m
+CONFIG_HID_CHERRY=m
 # CONFIG_HID_CHICONY is not set
 # CONFIG_HID_CYPRESS is not set
-# CONFIG_DRAGONRISE_FF is not set
-# CONFIG_HID_EZKEY is not set
+# CONFIG_HID_DRAGONRISE is not set
+CONFIG_HID_EZKEY=m
 # CONFIG_HID_KYE is not set
 # CONFIG_HID_GYRATION is not set
 # CONFIG_HID_KENSINGTON is not set
-# CONFIG_HID_LOGITECH is not set
-# CONFIG_HID_MICROSOFT is not set
+CONFIG_HID_LOGITECH=m
+# CONFIG_LOGITECH_FF is not set
+# CONFIG_LOGIRUMBLEPAD2_FF is not set
+CONFIG_HID_MICROSOFT=m
 # CONFIG_HID_MONTEREY is not set
 # CONFIG_HID_NTRIG is not set
 # CONFIG_HID_PANTHERLORD is not set
 # CONFIG_HID_PETALYNX is not set
 # CONFIG_HID_SAMSUNG is not set
 CONFIG_HID_SONY=m
-# CONFIG_HID_SUNPLUS is not set
-# CONFIG_GREENASIA_FF is not set
+CONFIG_HID_SUNPLUS=m
+# CONFIG_HID_GREENASIA is not set
+CONFIG_HID_SMARTJOYPLUS=m
+# CONFIG_SMARTJOYPLUS_FF is not set
 # CONFIG_HID_TOPSEED is not set
-# CONFIG_THRUSTMASTER_FF is not set
-# CONFIG_ZEROPLUS_FF is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_WACOM is not set
+# CONFIG_HID_ZEROPLUS is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -988,6 +931,8 @@ CONFIG_USB_EHCI_BIG_ENDIAN_MMIO=y
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
 CONFIG_USB_OHCI_HCD=m
+# CONFIG_USB_OHCI_HCD_PPC_OF_BE is not set
+# CONFIG_USB_OHCI_HCD_PPC_OF_LE is not set
 # CONFIG_USB_OHCI_HCD_PPC_OF is not set
 # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
 CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
@@ -1115,6 +1060,10 @@ CONFIG_RTC_DRV_PS3=m
 # CONFIG_DMADEVICES is not set
 # CONFIG_AUXDISPLAY is not set
 # CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
 # CONFIG_STAGING is not set
 
 #
@@ -1141,11 +1090,12 @@ CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
 # CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
 # CONFIG_XFS_FS is not set
 # CONFIG_GFS2_FS is not set
 # CONFIG_OCFS2_FS is not set
 # CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
 CONFIG_DNOTIFY=y
 CONFIG_INOTIFY=y
 CONFIG_INOTIFY_USER=y
@@ -1205,7 +1155,6 @@ CONFIG_MISC_FILESYSTEMS=y
 # CONFIG_BEFS_FS is not set
 # CONFIG_BFS_FS is not set
 # CONFIG_EFS_FS is not set
-# CONFIG_JFFS2_FS is not set
 # CONFIG_CRAMFS is not set
 # CONFIG_SQUASHFS is not set
 # CONFIG_VXFS_FS is not set
@@ -1222,6 +1171,7 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
 CONFIG_ROOT_NFS=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
@@ -1359,7 +1309,6 @@ CONFIG_DEBUG_MEMORY_INIT=y
 CONFIG_DEBUG_LIST=y
 # CONFIG_DEBUG_SG is not set
 # CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_BACKTRACE_SELF_TEST is not set
@@ -1374,31 +1323,21 @@ CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_RING_BUFFER=y
+CONFIG_EVENT_TRACING=y
+CONFIG_CONTEXT_SWITCH_TRACER=y
 CONFIG_TRACING=y
 CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_IRQSOFF_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_FTRACE_STARTUP_TEST is not set
+# CONFIG_FTRACE is not set
 # CONFIG_DYNAMIC_DEBUG is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
+# CONFIG_PPC_DISABLE_WERROR is not set
+CONFIG_PPC_WERROR=y
 CONFIG_PRINT_STACK_DEPTH=64
 CONFIG_DEBUG_STACKOVERFLOW=y
 # CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_PPC_EMULATED_STATS is not set
 # CONFIG_CODE_PATCHING_SELFTEST is not set
 # CONFIG_FTR_FIXUP_SELFTEST is not set
 # CONFIG_MSI_BITMAP_SELFTEST is not set
-- 
GitLab


From 52cef7555adf5ca09b3b7283097466759120d901 Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Mon, 24 Aug 2009 16:03:35 -0400
Subject: [PATCH 1084/1153] inotify: seperate new watch creation updating
 existing watches

There is nothing known wrong with the inotify watch addition/modification
but this patch seperates the two code paths to make them each easy to
verify as correct.

Signed-off-by: Eric Paris <eparis@redhat.com>
---
 fs/notify/inotify/inotify_user.c | 172 ++++++++++++++++++-------------
 1 file changed, 103 insertions(+), 69 deletions(-)

diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c
index dc32ed8323b..d8f73c25307 100644
--- a/fs/notify/inotify/inotify_user.c
+++ b/fs/notify/inotify/inotify_user.c
@@ -431,80 +431,29 @@ static void inotify_free_mark(struct fsnotify_mark_entry *entry)
 	kmem_cache_free(inotify_inode_mark_cachep, ientry);
 }
 
-static int inotify_update_watch(struct fsnotify_group *group, struct inode *inode, u32 arg)
+static int inotify_update_existing_watch(struct fsnotify_group *group,
+					 struct inode *inode,
+					 u32 arg)
 {
-	struct fsnotify_mark_entry *entry = NULL;
+	struct fsnotify_mark_entry *entry;
 	struct inotify_inode_mark_entry *ientry;
-	struct inotify_inode_mark_entry *tmp_ientry;
-	int ret = 0;
-	int add = (arg & IN_MASK_ADD);
-	__u32 mask;
 	__u32 old_mask, new_mask;
+	__u32 mask;
+	int add = (arg & IN_MASK_ADD);
+	int ret;
 
 	/* don't allow invalid bits: we don't want flags set */
 	mask = inotify_arg_to_mask(arg);
 	if (unlikely(!mask))
 		return -EINVAL;
 
-	tmp_ientry = kmem_cache_alloc(inotify_inode_mark_cachep, GFP_KERNEL);
-	if (unlikely(!tmp_ientry))
-		return -ENOMEM;
-	/* we set the mask at the end after attaching it */
-	fsnotify_init_mark(&tmp_ientry->fsn_entry, inotify_free_mark);
-	tmp_ientry->wd = -1;
-
-find_entry:
 	spin_lock(&inode->i_lock);
 	entry = fsnotify_find_mark_entry(group, inode);
 	spin_unlock(&inode->i_lock);
-	if (entry) {
-		ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry);
-	} else {
-		ret = -ENOSPC;
-		if (atomic_read(&group->inotify_data.user->inotify_watches) >= inotify_max_user_watches)
-			goto out_err;
-retry:
-		ret = -ENOMEM;
-		if (unlikely(!idr_pre_get(&group->inotify_data.idr, GFP_KERNEL)))
-			goto out_err;
-
-		spin_lock(&group->inotify_data.idr_lock);
-		ret = idr_get_new_above(&group->inotify_data.idr, &tmp_ientry->fsn_entry,
-					group->inotify_data.last_wd,
-					&tmp_ientry->wd);
-		spin_unlock(&group->inotify_data.idr_lock);
-		if (ret) {
-			if (ret == -EAGAIN)
-				goto retry;
-			goto out_err;
-		}
+	if (!entry)
+		return -ENOENT;
 
-		ret = fsnotify_add_mark(&tmp_ientry->fsn_entry, group, inode);
-		if (ret) {
-			inotify_remove_from_idr(group, tmp_ientry);
-			if (ret == -EEXIST)
-				goto find_entry;
-			goto out_err;
-		}
-
-		/* tmp_ientry has been added to the inode, so we are all set up.
-		 * now we just need to make sure tmp_ientry doesn't get freed and
-		 * we need to set up entry and ientry so the generic code can
-		 * do its thing. */
-		ientry = tmp_ientry;
-		entry = &ientry->fsn_entry;
-		tmp_ientry = NULL;
-
-		atomic_inc(&group->inotify_data.user->inotify_watches);
-
-		/* update the idr hint */
-		group->inotify_data.last_wd = ientry->wd;
-
-		/* we put the mark on the idr, take a reference */
-		fsnotify_get_mark(entry);
-	}
-
-	ret = ientry->wd;
+	ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry);
 
 	spin_lock(&entry->lock);
 
@@ -536,18 +485,103 @@ retry:
 			fsnotify_recalc_group_mask(group);
 	}
 
-	/* this either matches fsnotify_find_mark_entry, or init_mark_entry
-	 * depending on which path we took... */
+	/* return the wd */
+	ret = ientry->wd;
+
+	/* match the get from fsnotify_find_mark_entry() */
 	fsnotify_put_mark(entry);
 
+	return ret;
+}
+
+static int inotify_new_watch(struct fsnotify_group *group,
+			     struct inode *inode,
+			     u32 arg)
+{
+	struct inotify_inode_mark_entry *tmp_ientry;
+	__u32 mask;
+	int ret;
+
+	/* don't allow invalid bits: we don't want flags set */
+	mask = inotify_arg_to_mask(arg);
+	if (unlikely(!mask))
+		return -EINVAL;
+
+	tmp_ientry = kmem_cache_alloc(inotify_inode_mark_cachep, GFP_KERNEL);
+	if (unlikely(!tmp_ientry))
+		return -ENOMEM;
+
+	fsnotify_init_mark(&tmp_ientry->fsn_entry, inotify_free_mark);
+	tmp_ientry->fsn_entry.mask = mask;
+	tmp_ientry->wd = -1;
+
+	ret = -ENOSPC;
+	if (atomic_read(&group->inotify_data.user->inotify_watches) >= inotify_max_user_watches)
+		goto out_err;
+retry:
+	ret = -ENOMEM;
+	if (unlikely(!idr_pre_get(&group->inotify_data.idr, GFP_KERNEL)))
+		goto out_err;
+
+	spin_lock(&group->inotify_data.idr_lock);
+	ret = idr_get_new_above(&group->inotify_data.idr, &tmp_ientry->fsn_entry,
+				group->inotify_data.last_wd,
+				&tmp_ientry->wd);
+	spin_unlock(&group->inotify_data.idr_lock);
+	if (ret) {
+		/* idr was out of memory allocate and try again */
+		if (ret == -EAGAIN)
+			goto retry;
+		goto out_err;
+	}
+
+	/* we are on the idr, now get on the inode */
+	ret = fsnotify_add_mark(&tmp_ientry->fsn_entry, group, inode);
+	if (ret) {
+		/* we failed to get on the inode, get off the idr */
+		inotify_remove_from_idr(group, tmp_ientry);
+		goto out_err;
+	}
+
+	/* we put the mark on the idr, take a reference */
+	fsnotify_get_mark(&tmp_ientry->fsn_entry);
+
+	/* update the idr hint, who cares about races, it's just a hint */
+	group->inotify_data.last_wd = tmp_ientry->wd;
+
+	/* increment the number of watches the user has */
+	atomic_inc(&group->inotify_data.user->inotify_watches);
+
+	/* return the watch descriptor for this new entry */
+	ret = tmp_ientry->wd;
+
+	/* match the ref from fsnotify_init_markentry() */
+	fsnotify_put_mark(&tmp_ientry->fsn_entry);
+
 out_err:
-	/* could be an error, could be that we found an existing mark */
-	if (tmp_ientry) {
-		/* on the idr but didn't make it on the inode */
-		if (tmp_ientry->wd != -1)
-			inotify_remove_from_idr(group, tmp_ientry);
+	if (ret < 0)
 		kmem_cache_free(inotify_inode_mark_cachep, tmp_ientry);
-	}
+
+	return ret;
+}
+
+static int inotify_update_watch(struct fsnotify_group *group, struct inode *inode, u32 arg)
+{
+	int ret = 0;
+
+retry:
+	/* try to update and existing watch with the new arg */
+	ret = inotify_update_existing_watch(group, inode, arg);
+	/* no mark present, try to add a new one */
+	if (ret == -ENOENT)
+		ret = inotify_new_watch(group, inode, arg);
+	/*
+	 * inotify_new_watch could race with another thread which did an
+	 * inotify_new_watch between the update_existing and the add watch
+	 * here, go back and try to update an existing mark again.
+	 */
+	if (ret == -EEXIST)
+		goto retry;
 
 	return ret;
 }
-- 
GitLab


From cf4374267fbe966e8e4e7db68f5dc7b267439780 Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Mon, 24 Aug 2009 16:03:35 -0400
Subject: [PATCH 1085/1153] inotify: do not BUG on idr entries at inotify
 destruction

If an inotify watch is left in the idr when an fsnotify group is destroyed
this will lead to a BUG.  This is not a dangerous situation and really
indicates a programming bug and leak of memory.  This patch changes it to
use a WARN and a printk rather than killing people's boxes.

Signed-off-by: Eric Paris <eparis@redhat.com>
---
 fs/notify/inotify/inotify_fsnotify.c | 33 ++++++++++++++++++++++++++--
 1 file changed, 31 insertions(+), 2 deletions(-)

diff --git a/fs/notify/inotify/inotify_fsnotify.c b/fs/notify/inotify/inotify_fsnotify.c
index 5dcbafe72d7..c9ee67b442e 100644
--- a/fs/notify/inotify/inotify_fsnotify.c
+++ b/fs/notify/inotify/inotify_fsnotify.c
@@ -105,16 +105,45 @@ static bool inotify_should_send_event(struct fsnotify_group *group, struct inode
 	return send;
 }
 
+/*
+ * This is NEVER supposed to be called.  Inotify marks should either have been
+ * removed from the idr when the watch was removed or in the
+ * fsnotify_destroy_mark_by_group() call when the inotify instance was being
+ * torn down.  This is only called if the idr is about to be freed but there
+ * are still marks in it.
+ */
 static int idr_callback(int id, void *p, void *data)
 {
-	BUG();
+	struct fsnotify_mark_entry *entry;
+	struct inotify_inode_mark_entry *ientry;
+	static bool warned = false;
+
+	if (warned)
+		return 0;
+
+	warned = false;
+	entry = p;
+	ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry);
+
+	WARN(1, "inotify closing but id=%d for entry=%p in group=%p still in "
+		"idr.  Probably leaking memory\n", id, p, data);
+
+	/*
+	 * I'm taking the liberty of assuming that the mark in question is a
+	 * valid address and I'm dereferencing it.  This might help to figure
+	 * out why we got here and the panic is no worse than the original
+	 * BUG() that was here.
+	 */
+	if (entry)
+		printk(KERN_WARNING "entry->group=%p inode=%p wd=%d\n",
+			entry->group, entry->inode, ientry->wd);
 	return 0;
 }
 
 static void inotify_free_group_priv(struct fsnotify_group *group)
 {
 	/* ideally the idr is empty and we won't hit the BUG in teh callback */
-	idr_for_each(&group->inotify_data.idr, idr_callback, NULL);
+	idr_for_each(&group->inotify_data.idr, idr_callback, group);
 	idr_remove_all(&group->inotify_data.idr);
 	idr_destroy(&group->inotify_data.idr);
 }
-- 
GitLab


From dead537dd8a1c9495322c1d6f7c780697f474af0 Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Mon, 24 Aug 2009 16:03:35 -0400
Subject: [PATCH 1086/1153] inotify: fix locking around inotify watching in the
 idr

The are races around the idr storage of inotify watches.  It's possible
that a watch could be found from sys_inotify_rm_watch() in the idr, but it
could be removed from the idr before that code does it's removal.  Move the
locking and the refcnt'ing so that these have to happen atomically.

Signed-off-by: Eric Paris <eparis@redhat.com>
---
 fs/notify/inotify/inotify_user.c | 50 +++++++++++++++++++++++++-------
 1 file changed, 40 insertions(+), 10 deletions(-)

diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c
index d8f73c25307..ce1f5823e2c 100644
--- a/fs/notify/inotify/inotify_user.c
+++ b/fs/notify/inotify/inotify_user.c
@@ -364,20 +364,53 @@ static int inotify_find_inode(const char __user *dirname, struct path *path, uns
 	return error;
 }
 
+/*
+ * Remove the mark from the idr (if present) and drop the reference
+ * on the mark because it was in the idr.
+ */
 static void inotify_remove_from_idr(struct fsnotify_group *group,
 				    struct inotify_inode_mark_entry *ientry)
 {
 	struct idr *idr;
+	struct fsnotify_mark_entry *entry;
+	struct inotify_inode_mark_entry *found_ientry;
+	int wd;
 
 	spin_lock(&group->inotify_data.idr_lock);
 	idr = &group->inotify_data.idr;
-	idr_remove(idr, ientry->wd);
-	spin_unlock(&group->inotify_data.idr_lock);
+	wd = ientry->wd;
+
+	if (wd == -1)
+		goto out;
+
+	entry = idr_find(&group->inotify_data.idr, wd);
+	if (unlikely(!entry))
+		goto out;
+
+	found_ientry = container_of(entry, struct inotify_inode_mark_entry, fsn_entry);
+	if (unlikely(found_ientry != ientry)) {
+		/* We found an entry in the idr with the right wd, but it's
+		 * not the entry we were told to remove.  eparis seriously
+		 * fucked up somewhere. */
+		WARN_ON(1);
+		ientry->wd = -1;
+		goto out;
+	}
+
+	/* One ref for being in the idr, one ref held by the caller */
+	BUG_ON(atomic_read(&entry->refcnt) < 2);
+
+	idr_remove(idr, wd);
 	ientry->wd = -1;
+
+	/* removed from the idr, drop that ref */
+	fsnotify_put_mark(entry);
+out:
+	spin_unlock(&group->inotify_data.idr_lock);
 }
+
 /*
- * Send IN_IGNORED for this wd, remove this wd from the idr, and drop the
- * internal reference help on the mark because it is in the idr.
+ * Send IN_IGNORED for this wd, remove this wd from the idr.
  */
 void inotify_ignored_and_remove_idr(struct fsnotify_mark_entry *entry,
 				    struct fsnotify_group *group)
@@ -417,9 +450,6 @@ skip_send_ignore:
 	/* remove this entry from the idr */
 	inotify_remove_from_idr(group, ientry);
 
-	/* removed from idr, drop that reference */
-	fsnotify_put_mark(entry);
-
 	atomic_dec(&group->inotify_data.user->inotify_watches);
 }
 
@@ -535,6 +565,9 @@ retry:
 		goto out_err;
 	}
 
+	/* we put the mark on the idr, take a reference */
+	fsnotify_get_mark(&tmp_ientry->fsn_entry);
+
 	/* we are on the idr, now get on the inode */
 	ret = fsnotify_add_mark(&tmp_ientry->fsn_entry, group, inode);
 	if (ret) {
@@ -543,9 +576,6 @@ retry:
 		goto out_err;
 	}
 
-	/* we put the mark on the idr, take a reference */
-	fsnotify_get_mark(&tmp_ientry->fsn_entry);
-
 	/* update the idr hint, who cares about races, it's just a hint */
 	group->inotify_data.last_wd = tmp_ientry->wd;
 
-- 
GitLab


From 0db501bd0610ee0c0aca84d927f90bcccd09e2bd Mon Sep 17 00:00:00 2001
From: "Eric W. Biederman" <ebiederm@xmission.com>
Date: Thu, 27 Aug 2009 03:20:04 -0700
Subject: [PATCH 1087/1153] inotify: Ensure we alwasy write the terminating
 NULL.

Before the rewrite copy_event_to_user always wrote a terqminating '\0'
byte to user space after the filename.  Since the rewrite that
terminating byte was skipped if your filename is exactly a multiple of
event_size.  Ouch!

So add one byte to name_size before we round up and use clear_user to
set userspace to zero like /dev/zero does instead of copying the
strange nul_inotify_event.  I can't quite convince myself len_to_zero
will never exceed 16 and even if it doesn't clear_user should be more
efficient and a more accurate reflection of what the code is trying to
do.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
---
 fs/notify/inotify/inotify_user.c | 13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)

diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c
index ce1f5823e2c..0e781bc88d1 100644
--- a/fs/notify/inotify/inotify_user.c
+++ b/fs/notify/inotify/inotify_user.c
@@ -47,9 +47,6 @@
 
 static struct vfsmount *inotify_mnt __read_mostly;
 
-/* this just sits here and wastes global memory.  used to just pad userspace messages with zeros */
-static struct inotify_event nul_inotify_event;
-
 /* these are configurable via /proc/sys/fs/inotify/ */
 static int inotify_max_user_instances __read_mostly;
 static int inotify_max_queued_events __read_mostly;
@@ -199,8 +196,10 @@ static ssize_t copy_event_to_user(struct fsnotify_group *group,
 		inotify_free_event_priv(fsn_priv);
 	}
 
-	/* round up event->name_len so it is a multiple of event_size */
-	name_len = roundup(event->name_len, event_size);
+	/* round up event->name_len so it is a multiple of event_size
+	 * plus an extra byte for the terminating '\0'.
+	 */
+	name_len = roundup(event->name_len + 1, event_size);
 	inotify_event.len = name_len;
 
 	inotify_event.mask = inotify_mask_to_arg(event->mask);
@@ -224,8 +223,8 @@ static ssize_t copy_event_to_user(struct fsnotify_group *group,
 			return -EFAULT;
 		buf += event->name_len;
 
-		/* fill userspace with 0's from nul_inotify_event */
-		if (copy_to_user(buf, &nul_inotify_event, len_to_zero))
+		/* fill userspace with 0's */
+		if (clear_user(buf, len_to_zero))
 			return -EFAULT;
 		buf += len_to_zero;
 		event_size += name_len;
-- 
GitLab


From 9886e836a6a5dbd273dc55b17e713f0a188d137f Mon Sep 17 00:00:00 2001
From: David Howells <dhowells@redhat.com>
Date: Thu, 27 Aug 2009 13:09:06 +0100
Subject: [PATCH 1088/1153] AFS: Stop readlink() on AFS crashing due to NULL
 'file' ptr

kAFS crashes when asked to read a symbolic link because page_getlink()
passes a NULL file pointer to read_mapping_page(), but afs_readpage()
expects a file pointer from which to extract a key.

Modify afs_readpage() to request the appropriate key from the calling
process's keyrings if a file struct is not supplied with one attached.

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/afs/file.c | 18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)

diff --git a/fs/afs/file.c b/fs/afs/file.c
index 0149dab365e..681c2a7b013 100644
--- a/fs/afs/file.c
+++ b/fs/afs/file.c
@@ -134,9 +134,16 @@ static int afs_readpage(struct file *file, struct page *page)
 
 	inode = page->mapping->host;
 
-	ASSERT(file != NULL);
-	key = file->private_data;
-	ASSERT(key != NULL);
+	if (file) {
+		key = file->private_data;
+		ASSERT(key != NULL);
+	} else {
+		key = afs_request_key(AFS_FS_S(inode->i_sb)->volume->cell);
+		if (IS_ERR(key)) {
+			ret = PTR_ERR(key);
+			goto error_nokey;
+		}
+	}
 
 	_enter("{%x},{%lu},{%lu}", key_serial(key), inode->i_ino, page->index);
 
@@ -207,12 +214,17 @@ static int afs_readpage(struct file *file, struct page *page)
 		unlock_page(page);
 	}
 
+	if (!file)
+		key_put(key);
 	_leave(" = 0");
 	return 0;
 
 error:
 	SetPageError(page);
 	unlock_page(page);
+	if (!file)
+		key_put(key);
+error_nokey:
 	_leave(" = %d", ret);
 	return ret;
 }
-- 
GitLab


From 788d908f2879a17e5f80924f3da2e23f1034482d Mon Sep 17 00:00:00 2001
From: Julien TINNES <julien@cr0.org>
Date: Thu, 27 Aug 2009 15:26:58 +0200
Subject: [PATCH 1089/1153] ipv4: make ip_append_data() handle NULL routing
 table

Add a check in ip_append_data() for NULL *rtp to prevent future bugs in
callers from being exploitable.

Signed-off-by: Julien Tinnes <julien@cr0.org>
Signed-off-by: Tavis Ormandy <taviso@sdf.lonestar.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 net/ipv4/ip_output.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/net/ipv4/ip_output.c b/net/ipv4/ip_output.c
index 7d082105472..7ffcd96fe59 100644
--- a/net/ipv4/ip_output.c
+++ b/net/ipv4/ip_output.c
@@ -813,6 +813,8 @@ int ip_append_data(struct sock *sk,
 			inet->cork.addr = ipc->addr;
 		}
 		rt = *rtp;
+		if (unlikely(!rt))
+			return -EFAULT;
 		/*
 		 * We steal reference to this route, caller should not release it
 		 */
-- 
GitLab


From 4f8ee2c9cc0e885d2bb50ef26db66150ab25213e Mon Sep 17 00:00:00 2001
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Thu, 27 Aug 2009 17:20:30 +1000
Subject: [PATCH 1090/1153] lmb: Remove __init from lmb_end_of_DRAM()

We call lmb_end_of_DRAM() to test whether a DMA mask is ok on a machine
without IOMMU, but this function is marked as __init.

I don't think there's a clean way to get the top of RAM max_pfn doesn't
appear to include highmem or I missed (or we have a bug :-) so for now,
let's just avoid having a broken 2.6.31 by making this function
non-__init and we can revisit later.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 lib/lmb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/lib/lmb.c b/lib/lmb.c
index e4a6482d8b2..0343c05609f 100644
--- a/lib/lmb.c
+++ b/lib/lmb.c
@@ -429,7 +429,7 @@ u64 __init lmb_phys_mem_size(void)
 	return lmb.memory.size;
 }
 
-u64 __init lmb_end_of_DRAM(void)
+u64 lmb_end_of_DRAM(void)
 {
 	int idx = lmb.memory.cnt - 1;
 
-- 
GitLab


From 0a80fb10239b04c45e5e80aad8d4b2ca5ac407b2 Mon Sep 17 00:00:00 2001
From: Jeremy Fitzhardinge <jeremy@goop.org>
Date: Thu, 27 Aug 2009 12:22:43 -0700
Subject: [PATCH 1091/1153] xenfb: connect to backend before registering fb

As soon as the framebuffer is registered, our methods may be called by the
kernel. This leads to a crash as xenfb_refresh() gets called before we have
the irq.

Connect to the backend before registering our framebuffer with the kernel.

[ Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14059 ]

Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/video/xen-fbfront.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/video/xen-fbfront.c b/drivers/video/xen-fbfront.c
index 15502d5e364..54cd9161017 100644
--- a/drivers/video/xen-fbfront.c
+++ b/drivers/video/xen-fbfront.c
@@ -454,6 +454,10 @@ static int __devinit xenfb_probe(struct xenbus_device *dev,
 
 	xenfb_init_shared_page(info, fb_info);
 
+	ret = xenfb_connect_backend(dev, info);
+	if (ret < 0)
+		goto error;
+
 	ret = register_framebuffer(fb_info);
 	if (ret) {
 		fb_deferred_io_cleanup(fb_info);
@@ -464,10 +468,6 @@ static int __devinit xenfb_probe(struct xenbus_device *dev,
 	}
 	info->fb_info = fb_info;
 
-	ret = xenfb_connect_backend(dev, info);
-	if (ret < 0)
-		goto error;
-
 	xenfb_make_preferred_console();
 	return 0;
 
-- 
GitLab


From 7d1d16e416e61aeef8655d542f8e4a4fc6e808e4 Mon Sep 17 00:00:00 2001
From: Rusty Russell <rusty@rustcorp.com.au>
Date: Wed, 26 Aug 2009 22:02:54 +0930
Subject: [PATCH 1092/1153] module: fix BUG_ON() for powerpc (and other
 function descriptor archs)

The rarely-used symbol_put_addr() needs to use dereference_function_descriptor
on powerpc.

Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/module.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/kernel/module.c b/kernel/module.c
index fd141140355..07c80e68a6c 100644
--- a/kernel/module.c
+++ b/kernel/module.c
@@ -909,16 +909,18 @@ void __symbol_put(const char *symbol)
 }
 EXPORT_SYMBOL(__symbol_put);
 
+/* Note this assumes addr is a function, which it currently always is. */
 void symbol_put_addr(void *addr)
 {
 	struct module *modaddr;
+	unsigned long a = (unsigned long)dereference_function_descriptor(addr);
 
-	if (core_kernel_text((unsigned long)addr))
+	if (core_kernel_text(a))
 		return;
 
 	/* module_text_address is safe here: we're supposed to have reference
 	 * to module from symbol_get, so it can't go away. */
-	modaddr = __module_text_address((unsigned long)addr);
+	modaddr = __module_text_address(a);
 	BUG_ON(!modaddr);
 	module_put(modaddr);
 }
-- 
GitLab


From 1b364bf438cf337a3818aee77d68c0713f3e1fc4 Mon Sep 17 00:00:00 2001
From: James Bottomley <James.Bottomley@HansenPartnership.com>
Date: Wed, 26 Aug 2009 22:04:12 +0930
Subject: [PATCH 1093/1153] module: workaround duplicate section names

The root cause is a duplicate section name (.text); is this legal?
[ Amerigo Wang: "AFAIK, yes." ]

However, there's a problem with commit
6d76013381ed28979cd122eb4b249a88b5e384fa in that if you fail to allocate
a mod->sect_attrs (in this case it's null because of the duplication),
it still gets used without checking in add_notes_attrs()

This should fix it

[ This patch leaves other problems, particularly the sections directory,
  but recent parisc toolchains seem to produce these modules and this
  prevents a crash and is a minimal change -- RR ]

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/module.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/kernel/module.c b/kernel/module.c
index 07c80e68a6c..eccb561dd8a 100644
--- a/kernel/module.c
+++ b/kernel/module.c
@@ -2355,7 +2355,8 @@ static noinline struct module *load_module(void __user *umod,
 	if (err < 0)
 		goto unlink;
 	add_sect_attrs(mod, hdr->e_shnum, secstrings, sechdrs);
-	add_notes_attrs(mod, hdr->e_shnum, secstrings, sechdrs);
+	if (mod->sect_attrs)
+		add_notes_attrs(mod, hdr->e_shnum, secstrings, sechdrs);
 
 	/* Get rid of temporary copy */
 	vfree(hdr);
-- 
GitLab


From 326ba5010a5429a5a528b268b36a5900d4ab0eba Mon Sep 17 00:00:00 2001
From: Linus Torvalds <torvalds@linux-foundation.org>
Date: Thu, 27 Aug 2009 17:59:04 -0700
Subject: [PATCH 1094/1153] Linux 2.6.31-rc8

---
 Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Makefile b/Makefile
index 9c87e60d169..25c615e5730 100644
--- a/Makefile
+++ b/Makefile
@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 31
-EXTRAVERSION = -rc7
+EXTRAVERSION = -rc8
 NAME = Man-Eating Seals of Antiquity
 
 # *DOCUMENTATION*
-- 
GitLab


From b962e7312ae87006aed6f68ceee94bdf8db08338 Mon Sep 17 00:00:00 2001
From: Brian Rogers <brian@xyzw.org>
Date: Fri, 28 Aug 2009 10:00:05 -0400
Subject: [PATCH 1095/1153] inotify: do not send a block of zeros when no
 pathname is available

When an event has no pathname, there's no need to pad it with a null byte and
therefore generate an inotify_event sized block of zeros. This fixes a
regression introduced by commit 0db501bd0610ee0c0aca84d927f90bcccd09e2bd where
my system wouldn't finish booting because some process was being confused by
this.

Signed-off-by: Brian Rogers <brian@xyzw.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
---
 fs/notify/inotify/inotify_user.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c
index 0e781bc88d1..b547ae17b46 100644
--- a/fs/notify/inotify/inotify_user.c
+++ b/fs/notify/inotify/inotify_user.c
@@ -180,7 +180,7 @@ static ssize_t copy_event_to_user(struct fsnotify_group *group,
 	struct fsnotify_event_private_data *fsn_priv;
 	struct inotify_event_private_data *priv;
 	size_t event_size = sizeof(struct inotify_event);
-	size_t name_len;
+	size_t name_len = 0;
 
 	/* we get the inotify watch descriptor from the event private data */
 	spin_lock(&event->lock);
@@ -196,10 +196,12 @@ static ssize_t copy_event_to_user(struct fsnotify_group *group,
 		inotify_free_event_priv(fsn_priv);
 	}
 
-	/* round up event->name_len so it is a multiple of event_size
+	/*
+	 * round up event->name_len so it is a multiple of event_size
 	 * plus an extra byte for the terminating '\0'.
 	 */
-	name_len = roundup(event->name_len + 1, event_size);
+	if (event->name_len)
+		name_len = roundup(event->name_len + 1, event_size);
 	inotify_event.len = name_len;
 
 	inotify_event.mask = inotify_mask_to_arg(event->mask);
-- 
GitLab


From 83cb10f0ef3c96162be92339ccf8c0c9c9f2d13e Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Fri, 28 Aug 2009 11:57:55 -0400
Subject: [PATCH 1096/1153] inotify: fix length reporting and size checking

0db501bd0610ee0c0 introduced a regresion in that it now sends a nul
terminator but the length accounting when checking for space or
reporting to userspace did not take this into account.  This corrects
all of the rounding logic.

Signed-off-by: Eric Paris <eparis@redhat.com>
---
 fs/notify/inotify/inotify_user.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c
index b547ae17b46..6111670b257 100644
--- a/fs/notify/inotify/inotify_user.c
+++ b/fs/notify/inotify/inotify_user.c
@@ -154,7 +154,8 @@ static struct fsnotify_event *get_one_event(struct fsnotify_group *group,
 
 	event = fsnotify_peek_notify_event(group);
 
-	event_size += roundup(event->name_len, event_size);
+	if (event->name_len)
+		event_size += roundup(event->name_len + 1, event_size);
 
 	if (event_size > count)
 		return ERR_PTR(-EINVAL);
@@ -327,8 +328,9 @@ static long inotify_ioctl(struct file *file, unsigned int cmd,
 		list_for_each_entry(holder, &group->notification_list, event_list) {
 			event = holder->event;
 			send_len += sizeof(struct inotify_event);
-			send_len += roundup(event->name_len,
-					     sizeof(struct inotify_event));
+			if (event->name_len)
+				send_len += roundup(event->name_len + 1,
+						sizeof(struct inotify_event));
 		}
 		mutex_unlock(&group->notification_mutex);
 		ret = put_user(send_len, (int __user *) p);
-- 
GitLab


From 750a8870fe4016ef3091fc97e084d58c613c2cc7 Mon Sep 17 00:00:00 2001
From: Eric Paris <eparis@redhat.com>
Date: Fri, 28 Aug 2009 12:50:47 -0400
Subject: [PATCH 1097/1153] inotify: update the group mask on mark addition

Seperating the addition and update of marks in inotify resulted in a
regression in that inotify never gets events.  The inotify group mask is
always 0.  This mask should be updated any time a new mark is added.

Signed-off-by: Eric Paris <eparis@redhat.com>
---
 fs/notify/inotify/inotify_user.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/fs/notify/inotify/inotify_user.c b/fs/notify/inotify/inotify_user.c
index 6111670b257..dcd2040d330 100644
--- a/fs/notify/inotify/inotify_user.c
+++ b/fs/notify/inotify/inotify_user.c
@@ -591,6 +591,10 @@ retry:
 	/* match the ref from fsnotify_init_markentry() */
 	fsnotify_put_mark(&tmp_ientry->fsn_entry);
 
+	/* if this mark added a new event update the group mask */
+	if (mask & ~group->mask)
+		fsnotify_recalc_group_mask(group);
+
 out_err:
 	if (ret < 0)
 		kmem_cache_free(inotify_inode_mark_cachep, tmp_ientry);
-- 
GitLab


From b0de22bdffa2e9a8e280d769c59f866605268484 Mon Sep 17 00:00:00 2001
From: Lin Ming <ming.m.lin@intel.com>
Date: Wed, 26 Aug 2009 09:01:34 +0800
Subject: [PATCH 1098/1153] ACPICA: Windows compatibility fix: same
 buffer/string store

Fix a compatibility issue when the same buffer or string is
stored to itself. This has been seen in the field. Previously,
ACPICA would zero out the buffer/string. Now, the operation is
treated as a NOP.

http://bugzilla.acpica.org/show_bug.cgi?id=803

Reported-by: Rezwanul Kabir <Rezwanul_Kabir@Dell.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/acpi/acpica/exstorob.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/drivers/acpi/acpica/exstorob.c b/drivers/acpi/acpica/exstorob.c
index 67340cc7014..257706e7734 100644
--- a/drivers/acpi/acpica/exstorob.c
+++ b/drivers/acpi/acpica/exstorob.c
@@ -70,6 +70,12 @@ acpi_ex_store_buffer_to_buffer(union acpi_operand_object *source_desc,
 
 	ACPI_FUNCTION_TRACE_PTR(ex_store_buffer_to_buffer, source_desc);
 
+	/* If Source and Target are the same, just return */
+
+	if (source_desc == target_desc) {
+		return_ACPI_STATUS(AE_OK);
+	}
+
 	/* We know that source_desc is a buffer by now */
 
 	buffer = ACPI_CAST_PTR(u8, source_desc->buffer.pointer);
@@ -161,6 +167,12 @@ acpi_ex_store_string_to_string(union acpi_operand_object *source_desc,
 
 	ACPI_FUNCTION_TRACE_PTR(ex_store_string_to_string, source_desc);
 
+	/* If Source and Target are the same, just return */
+
+	if (source_desc == target_desc) {
+		return_ACPI_STATUS(AE_OK);
+	}
+
 	/* We know that source_desc is a string by now */
 
 	buffer = ACPI_CAST_PTR(u8, source_desc->string.pointer);
-- 
GitLab


From 82e7784f57a81faf673b09bc468e736d582fe754 Mon Sep 17 00:00:00 2001
From: Jiri Slaby <jirislaby@gmail.com>
Date: Thu, 6 Aug 2009 15:57:51 -0700
Subject: [PATCH 1099/1153] toshiba_acpi: return on a fail path

Return from bt_rfkill_poll() when hci_get_radio_state() fails.

value is invalid in that case and should not be assigned to the rfkill
state.

This also fixes a double unlock bug.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/platform/x86/toshiba_acpi.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/platform/x86/toshiba_acpi.c b/drivers/platform/x86/toshiba_acpi.c
index 81d31ea507d..51c0a8bee41 100644
--- a/drivers/platform/x86/toshiba_acpi.c
+++ b/drivers/platform/x86/toshiba_acpi.c
@@ -335,6 +335,7 @@ static void bt_rfkill_poll(struct rfkill *rfkill, void *data)
 	if (hci_result != HCI_SUCCESS) {
 		/* Can't do anything useful */
 		mutex_unlock(&dev->mutex);
+		return;
 	}
 
 	new_rfk_state = value;
-- 
GitLab


From e29b3ee3b005897fbdcfdd4b3190776e38739d70 Mon Sep 17 00:00:00 2001
From: Keith Packard <keithp@keithp.com>
Date: Thu, 6 Aug 2009 15:57:54 -0700
Subject: [PATCH 1100/1153] ACPI: don't free non-existent backlight in acpi
 video module

acpi_video_put_one_device was attempting to remove sysfs entries and
unregister a backlight device without first checking that said backlight
device structure had been created.

Signed-off-by: Keith Packard <keithp@keithp.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
---
 drivers/acpi/video.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/acpi/video.c b/drivers/acpi/video.c
index 8851315ce85..60ea984c84a 100644
--- a/drivers/acpi/video.c
+++ b/drivers/acpi/video.c
@@ -2004,8 +2004,11 @@ static int acpi_video_bus_put_one_device(struct acpi_video_device *device)
 	status = acpi_remove_notify_handler(device->dev->handle,
 					    ACPI_DEVICE_NOTIFY,
 					    acpi_video_device_notify);
-	sysfs_remove_link(&device->backlight->dev.kobj, "device");
-	backlight_device_unregister(device->backlight);
+	if (device->backlight) {
+		sysfs_remove_link(&device->backlight->dev.kobj, "device");
+		backlight_device_unregister(device->backlight);
+		device->backlight = NULL;
+	}
 	if (device->cdev) {
 		sysfs_remove_link(&device->dev->dev.kobj,
 				  "thermal_cooling");
-- 
GitLab


From ea6bff368548d79529421a9dc0710fc5330eb504 Mon Sep 17 00:00:00 2001
From: Ingo Molnar <mingo@elte.hu>
Date: Fri, 28 Aug 2009 10:44:56 +0200
Subject: [PATCH 1101/1153] modules: Fix build error in the !CONFIG_KALLSYMS
 case
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

> James Bottomley (1):
>       module: workaround duplicate section names

-tip testing found that this patch breaks the build on x86 if
CONFIG_KALLSYMS is disabled:

 kernel/module.c: In function ‘load_module’:
 kernel/module.c:2367: error: ‘struct module’ has no member named ‘sect_attrs’
 distcc[8269] ERROR: compile kernel/module.c on ph/32 failed
 make[1]: *** [kernel/module.o] Error 1
 make: *** [kernel] Error 2
 make: *** Waiting for unfinished jobs....

Commit 1b364bf misses the fact that section attributes are only
built and dealt with if kallsyms is enabled. The patch below fixes
this.

( note, technically speaking this should depend on CONFIG_SYSFS as
  well but this patch is correct too and keeps the #ifdef less
  intrusive - in the KALLSYMS && !SYSFS case the code is a NOP. )

Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Replaced patch with a slightly cleaner variation by James Bottomley ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 kernel/module.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/kernel/module.c b/kernel/module.c
index eccb561dd8a..2d537186191 100644
--- a/kernel/module.c
+++ b/kernel/module.c
@@ -1274,6 +1274,10 @@ static void add_notes_attrs(struct module *mod, unsigned int nsect,
 	struct module_notes_attrs *notes_attrs;
 	struct bin_attribute *nattr;
 
+	/* failed to create section attributes, so can't create notes */
+	if (!mod->sect_attrs)
+		return;
+
 	/* Count notes sections and allocate structures.  */
 	notes = 0;
 	for (i = 0; i < nsect; i++)
@@ -2355,8 +2359,7 @@ static noinline struct module *load_module(void __user *umod,
 	if (err < 0)
 		goto unlink;
 	add_sect_attrs(mod, hdr->e_shnum, secstrings, sechdrs);
-	if (mod->sect_attrs)
-		add_notes_attrs(mod, hdr->e_shnum, secstrings, sechdrs);
+	add_notes_attrs(mod, hdr->e_shnum, secstrings, sechdrs);
 
 	/* Get rid of temporary copy */
 	vfree(hdr);
-- 
GitLab


From 2574cc9f4ffc6c681c9177111357efe5b76f0e36 Mon Sep 17 00:00:00 2001
From: Trond Myklebust <Trond.Myklebust@netapp.com>
Date: Fri, 28 Aug 2009 11:12:12 -0400
Subject: [PATCH 1102/1153] SUNRPC: Fix rpc_task_force_reencode

This patch fixes the bug that was reported in
  http://bugzilla.kernel.org/show_bug.cgi?id=14053

If we're in the case where we need to force a reencode and then resend of
the RPC request, due to xprt_transmit failing with a networking error, then
we _must_ retransmit the entire request.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 net/sunrpc/clnt.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/net/sunrpc/clnt.c b/net/sunrpc/clnt.c
index ebfcf9b8990..df1039f077c 100644
--- a/net/sunrpc/clnt.c
+++ b/net/sunrpc/clnt.c
@@ -937,6 +937,7 @@ static inline void
 rpc_task_force_reencode(struct rpc_task *task)
 {
 	task->tk_rqstp->rq_snd_buf.len = 0;
+	task->tk_rqstp->rq_bytes_sent = 0;
 }
 
 static inline void
-- 
GitLab


From 825e1e23914b9c3dbc49ee8c5a1d1cb421c1270a Mon Sep 17 00:00:00 2001
From: Grant Grundler <grundler@parisc-linux.org>
Date: Fri, 28 Aug 2009 15:00:36 -0400
Subject: [PATCH 1103/1153] parisc: fix warning in traps.c

On Tue, Aug 18, 2009 at 01:45:17PM -0400, John David Anglin wrote:
>  CC      arch/parisc/kernel/traps.o
> arch/parisc/kernel/traps.c: In function 'handle_interruption':
> arch/parisc/kernel/traps.c:535:18: warning: operation on 'regs->iasq[0]'
> may be undefined

Yes - Line 535 should use both [0] and [1].

Reported-by: John David Anglin <dave@hiauly1.hia.nrc.ca>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 arch/parisc/kernel/traps.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/parisc/kernel/traps.c b/arch/parisc/kernel/traps.c
index 528f0ff9b27..8b58bf0b7d5 100644
--- a/arch/parisc/kernel/traps.c
+++ b/arch/parisc/kernel/traps.c
@@ -532,7 +532,7 @@ void notrace handle_interruption(int code, struct pt_regs *regs)
 	  	/* Kill the user process later */
 	  	regs->iaoq[0] = 0 | 3;
 		regs->iaoq[1] = regs->iaoq[0] + 4;
-	 	regs->iasq[0] = regs->iasq[0] = regs->sr[7];
+	 	regs->iasq[0] = regs->iasq[1] = regs->sr[7];
 		regs->gr[0] &= ~PSW_B;
 		return;
 	}
-- 
GitLab


From a09ba7faf75fa4b21980d81de8e5f3d5c0785ccf Mon Sep 17 00:00:00 2001
From: Eric Anholt <eric@anholt.net>
Date: Sat, 29 Aug 2009 12:49:51 -0700
Subject: [PATCH 1104/1153] drm/i915: Fix CPU-spinning hangs related to fence
 usage by using an LRU.

The lack of a proper LRU was partially worked around by taking the fence
from the object containing the oldest seqno.  But if there are multiple
objects inactive, then they don't have seqnos and the first fence reg
among them would be chosen.  If you were trying to copy data between two
mappings, this could result in each page fault stealing the fence from
the other argument, and your application hanging.

https://bugs.freedesktop.org/show_bug.cgi?id=23566
https://bugs.freedesktop.org/show_bug.cgi?id=23220
https://bugs.freedesktop.org/show_bug.cgi?id=23253
https://bugs.freedesktop.org/show_bug.cgi?id=23366

Cc: Stable Team <stable@kernel.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
---
 drivers/gpu/drm/i915/i915_drv.h |  6 +++
 drivers/gpu/drm/i915/i915_gem.c | 86 ++++++++++++++++++---------------
 2 files changed, 54 insertions(+), 38 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 7537f57d8a8..11fc4b66c88 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -384,6 +384,9 @@ typedef struct drm_i915_private {
 		 */
 		struct list_head inactive_list;
 
+		/** LRU list of objects with fence regs on them. */
+		struct list_head fence_list;
+
 		/**
 		 * List of breadcrumbs associated with GPU requests currently
 		 * outstanding.
@@ -451,6 +454,9 @@ struct drm_i915_gem_object {
 	/** This object's place on the active/flushing/inactive lists */
 	struct list_head list;
 
+	/** This object's place on the fenced object LRU */
+	struct list_head fence_list;
+
 	/**
 	 * This is set if the object is on the active or flushing lists
 	 * (has pending rendering), and is not set if it's on inactive (ready
diff --git a/drivers/gpu/drm/i915/i915_gem.c b/drivers/gpu/drm/i915/i915_gem.c
index 140bee142fc..0c07a755b3a 100644
--- a/drivers/gpu/drm/i915/i915_gem.c
+++ b/drivers/gpu/drm/i915/i915_gem.c
@@ -978,6 +978,7 @@ int
 i915_gem_set_domain_ioctl(struct drm_device *dev, void *data,
 			  struct drm_file *file_priv)
 {
+	struct drm_i915_private *dev_priv = dev->dev_private;
 	struct drm_i915_gem_set_domain *args = data;
 	struct drm_gem_object *obj;
 	uint32_t read_domains = args->read_domains;
@@ -1010,8 +1011,18 @@ i915_gem_set_domain_ioctl(struct drm_device *dev, void *data,
 		 obj, obj->size, read_domains, write_domain);
 #endif
 	if (read_domains & I915_GEM_DOMAIN_GTT) {
+		struct drm_i915_gem_object *obj_priv = obj->driver_private;
+
 		ret = i915_gem_object_set_to_gtt_domain(obj, write_domain != 0);
 
+		/* Update the LRU on the fence for the CPU access that's
+		 * about to occur.
+		 */
+		if (obj_priv->fence_reg != I915_FENCE_REG_NONE) {
+			list_move_tail(&obj_priv->fence_list,
+				       &dev_priv->mm.fence_list);
+		}
+
 		/* Silently promote "you're not bound, there was nothing to do"
 		 * to success, since the client was just asking us to
 		 * make sure everything was done.
@@ -1155,8 +1166,7 @@ int i915_gem_fault(struct vm_area_struct *vma, struct vm_fault *vmf)
 	}
 
 	/* Need a new fence register? */
-	if (obj_priv->fence_reg == I915_FENCE_REG_NONE &&
-	    obj_priv->tiling_mode != I915_TILING_NONE) {
+	if (obj_priv->tiling_mode != I915_TILING_NONE) {
 		ret = i915_gem_object_get_fence_reg(obj);
 		if (ret) {
 			mutex_unlock(&dev->struct_mutex);
@@ -2208,6 +2218,12 @@ i915_gem_object_get_fence_reg(struct drm_gem_object *obj)
 	struct drm_i915_gem_object *old_obj_priv = NULL;
 	int i, ret, avail;
 
+	/* Just update our place in the LRU if our fence is getting used. */
+	if (obj_priv->fence_reg != I915_FENCE_REG_NONE) {
+		list_move_tail(&obj_priv->fence_list, &dev_priv->mm.fence_list);
+		return 0;
+	}
+
 	switch (obj_priv->tiling_mode) {
 	case I915_TILING_NONE:
 		WARN(1, "allocating a fence for non-tiled object?\n");
@@ -2229,7 +2245,6 @@ i915_gem_object_get_fence_reg(struct drm_gem_object *obj)
 	}
 
 	/* First try to find a free reg */
-try_again:
 	avail = 0;
 	for (i = dev_priv->fence_reg_start; i < dev_priv->num_fence_regs; i++) {
 		reg = &dev_priv->fence_regs[i];
@@ -2243,52 +2258,41 @@ try_again:
 
 	/* None available, try to steal one or wait for a user to finish */
 	if (i == dev_priv->num_fence_regs) {
-		uint32_t seqno = dev_priv->mm.next_gem_seqno;
+		struct drm_gem_object *old_obj = NULL;
 
 		if (avail == 0)
 			return -ENOSPC;
 
-		for (i = dev_priv->fence_reg_start;
-		     i < dev_priv->num_fence_regs; i++) {
-			uint32_t this_seqno;
+		list_for_each_entry(old_obj_priv, &dev_priv->mm.fence_list,
+				    fence_list) {
+			old_obj = old_obj_priv->obj;
 
-			reg = &dev_priv->fence_regs[i];
-			old_obj_priv = reg->obj->driver_private;
+			reg = &dev_priv->fence_regs[old_obj_priv->fence_reg];
 
 			if (old_obj_priv->pin_count)
 				continue;
 
+			/* Take a reference, as otherwise the wait_rendering
+			 * below may cause the object to get freed out from
+			 * under us.
+			 */
+			drm_gem_object_reference(old_obj);
+
 			/* i915 uses fences for GPU access to tiled buffers */
 			if (IS_I965G(dev) || !old_obj_priv->active)
 				break;
 
-			/* find the seqno of the first available fence */
-			this_seqno = old_obj_priv->last_rendering_seqno;
-			if (this_seqno != 0 &&
-			    reg->obj->write_domain == 0 &&
-			    i915_seqno_passed(seqno, this_seqno))
-				seqno = this_seqno;
-		}
-
-		/*
-		 * Now things get ugly... we have to wait for one of the
-		 * objects to finish before trying again.
-		 */
-		if (i == dev_priv->num_fence_regs) {
-			if (seqno == dev_priv->mm.next_gem_seqno) {
-				i915_gem_flush(dev,
-					       I915_GEM_GPU_DOMAINS,
-					       I915_GEM_GPU_DOMAINS);
-				seqno = i915_add_request(dev, NULL,
-							 I915_GEM_GPU_DOMAINS);
-				if (seqno == 0)
-					return -ENOMEM;
-			}
-
-			ret = i915_wait_request(dev, seqno);
-			if (ret)
+			/* This brings the object to the head of the LRU if it
+			 * had been written to.  The only way this should
+			 * result in us waiting longer than the expected
+			 * optimal amount of time is if there was a
+			 * fence-using buffer later that was read-only.
+			 */
+			i915_gem_object_flush_gpu_write_domain(old_obj);
+			ret = i915_gem_object_wait_rendering(old_obj);
+			if (ret != 0)
 				return ret;
-			goto try_again;
+			break;
 		}
 
 		/*
@@ -2296,10 +2300,15 @@ try_again:
 		 * for this object next time we need it.
 		 */
 		i915_gem_release_mmap(reg->obj);
+		i = old_obj_priv->fence_reg;
 		old_obj_priv->fence_reg = I915_FENCE_REG_NONE;
+		list_del_init(&old_obj_priv->fence_list);
+		drm_gem_object_unreference(old_obj);
 	}
 
 	obj_priv->fence_reg = i;
+	list_add_tail(&obj_priv->fence_list, &dev_priv->mm.fence_list);
+
 	reg->obj = obj;
 
 	if (IS_I965G(dev))
@@ -2342,6 +2351,7 @@ i915_gem_clear_fence_reg(struct drm_gem_object *obj)
 
 	dev_priv->fence_regs[obj_priv->fence_reg].obj = NULL;
 	obj_priv->fence_reg = I915_FENCE_REG_NONE;
+	list_del_init(&obj_priv->fence_list);
 }
 
 /**
@@ -3595,9 +3605,7 @@ i915_gem_object_pin(struct drm_gem_object *obj, uint32_t alignment)
 	 * Pre-965 chips need a fence register set up in order to
 	 * properly handle tiled surfaces.
 	 */
-	if (!IS_I965G(dev) &&
-	    obj_priv->fence_reg == I915_FENCE_REG_NONE &&
-	    obj_priv->tiling_mode != I915_TILING_NONE) {
+	if (!IS_I965G(dev) && obj_priv->tiling_mode != I915_TILING_NONE) {
 		ret = i915_gem_object_get_fence_reg(obj);
 		if (ret != 0) {
 			if (ret != -EBUSY && ret != -ERESTARTSYS)
@@ -3806,6 +3814,7 @@ int i915_gem_init_object(struct drm_gem_object *obj)
 	obj_priv->obj = obj;
 	obj_priv->fence_reg = I915_FENCE_REG_NONE;
 	INIT_LIST_HEAD(&obj_priv->list);
+	INIT_LIST_HEAD(&obj_priv->fence_list);
 
 	return 0;
 }
@@ -4253,6 +4262,7 @@ i915_gem_load(struct drm_device *dev)
 	INIT_LIST_HEAD(&dev_priv->mm.flushing_list);
 	INIT_LIST_HEAD(&dev_priv->mm.inactive_list);
 	INIT_LIST_HEAD(&dev_priv->mm.request_list);
+	INIT_LIST_HEAD(&dev_priv->mm.fence_list);
 	INIT_DELAYED_WORK(&dev_priv->mm.retire_work,
 			  i915_gem_retire_work_handler);
 	dev_priv->mm.next_gem_seqno = 1;
-- 
GitLab


From db54501900ad3665dd669f5708ecd04fc5aed495 Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?David=20M=C3=BCller=20=28ELSOFT=20AG=29?=
 <d.mueller@elsoft.ch>
Date: Sat, 29 Aug 2009 08:54:45 +0200
Subject: [PATCH 1105/1153] drm/i915: Improve CRTDDC mapping by using VBT info
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Use VBT information to determine which DDC bus to use for CRTDCC.
Fall back to GPIOA if VBT info is not available.

Signed-off-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested on: 855 (David), and 945GM, 965GM, GM45, and G45 (anholt)
---
 drivers/gpu/drm/i915/i915_drv.h   |  1 +
 drivers/gpu/drm/i915/intel_bios.c | 51 +++++++++++++++++++++++++++++--
 drivers/gpu/drm/i915/intel_crt.c  |  7 ++++-
 3 files changed, 55 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
index 11fc4b66c88..5b4f87e5562 100644
--- a/drivers/gpu/drm/i915/i915_drv.h
+++ b/drivers/gpu/drm/i915/i915_drv.h
@@ -222,6 +222,7 @@ typedef struct drm_i915_private {
 	unsigned int edp_support:1;
 	int lvds_ssc_freq;
 
+	int crt_ddc_bus; /* -1 = unknown, else GPIO to use for CRT DDC */
 	struct drm_i915_fence_reg fence_regs[16]; /* assume 965 */
 	int fence_reg_start; /* 4 if userland hasn't ioctl'd us yet */
 	int num_fence_regs; /* 8 on pre-965, 16 otherwise */
diff --git a/drivers/gpu/drm/i915/intel_bios.c b/drivers/gpu/drm/i915/intel_bios.c
index 300aee3296c..f806fcc54e0 100644
--- a/drivers/gpu/drm/i915/intel_bios.c
+++ b/drivers/gpu/drm/i915/intel_bios.c
@@ -59,6 +59,16 @@ find_section(struct bdb_header *bdb, int section_id)
 	return NULL;
 }
 
+static u16
+get_blocksize(void *p)
+{
+	u16 *block_ptr, block_size;
+
+	block_ptr = (u16 *)((char *)p - 2);
+	block_size = *block_ptr;
+	return block_size;
+}
+
 static void
 fill_detail_timing_data(struct drm_display_mode *panel_fixed_mode,
 			struct lvds_dvo_timing *dvo_timing)
@@ -214,6 +224,41 @@ parse_general_features(struct drm_i915_private *dev_priv,
 	}
 }
 
+static void
+parse_general_definitions(struct drm_i915_private *dev_priv,
+			  struct bdb_header *bdb)
+{
+	struct bdb_general_definitions *general;
+	const int crt_bus_map_table[] = {
+		GPIOB,
+		GPIOA,
+		GPIOC,
+		GPIOD,
+		GPIOE,
+		GPIOF,
+	};
+
+	/* Set sensible defaults in case we can't find the general block
+	   or it is the wrong chipset */
+	dev_priv->crt_ddc_bus = -1;
+
+	general = find_section(bdb, BDB_GENERAL_DEFINITIONS);
+	if (general) {
+		u16 block_size = get_blocksize(general);
+		if (block_size >= sizeof(*general)) {
+			int bus_pin = general->crt_ddc_gmbus_pin;
+			DRM_DEBUG("crt_ddc_bus_pin: %d\n", bus_pin);
+			if ((bus_pin >= 1) && (bus_pin <= 6)) {
+				dev_priv->crt_ddc_bus =
+					crt_bus_map_table[bus_pin-1];
+			}
+		} else {
+			DRM_DEBUG("BDB_GD too small (%d). Invalid.\n",
+				  block_size);
+		}
+	}
+}
+
 static void
 parse_sdvo_device_mapping(struct drm_i915_private *dev_priv,
 		       struct bdb_header *bdb)
@@ -222,7 +267,7 @@ parse_sdvo_device_mapping(struct drm_i915_private *dev_priv,
 	struct bdb_general_definitions *p_defs;
 	struct child_device_config *p_child;
 	int i, child_device_num, count;
-	u16	block_size, *block_ptr;
+	u16	block_size;
 
 	p_defs = find_section(bdb, BDB_GENERAL_DEFINITIONS);
 	if (!p_defs) {
@@ -240,8 +285,7 @@ parse_sdvo_device_mapping(struct drm_i915_private *dev_priv,
 		return;
 	}
 	/* get the block size of general definitions */
-	block_ptr = (u16 *)((char *)p_defs - 2);
-	block_size = *block_ptr;
+	block_size = get_blocksize(p_defs);
 	/* get the number of child device */
 	child_device_num = (block_size - sizeof(*p_defs)) /
 				sizeof(*p_child);
@@ -362,6 +406,7 @@ intel_init_bios(struct drm_device *dev)
 
 	/* Grab useful general definitions */
 	parse_general_features(dev_priv, bdb);
+	parse_general_definitions(dev_priv, bdb);
 	parse_lfp_panel_data(dev_priv, bdb);
 	parse_sdvo_panel_data(dev_priv, bdb);
 	parse_sdvo_device_mapping(dev_priv, bdb);
diff --git a/drivers/gpu/drm/i915/intel_crt.c b/drivers/gpu/drm/i915/intel_crt.c
index d1294978a38..590f81c8f59 100644
--- a/drivers/gpu/drm/i915/intel_crt.c
+++ b/drivers/gpu/drm/i915/intel_crt.c
@@ -508,6 +508,7 @@ void intel_crt_init(struct drm_device *dev)
 {
 	struct drm_connector *connector;
 	struct intel_output *intel_output;
+	struct drm_i915_private *dev_priv = dev->dev_private;
 	u32 i2c_reg;
 
 	intel_output = kzalloc(sizeof(struct intel_output), GFP_KERNEL);
@@ -527,8 +528,12 @@ void intel_crt_init(struct drm_device *dev)
 	/* Set up the DDC bus. */
 	if (IS_IGDNG(dev))
 		i2c_reg = PCH_GPIOA;
-	else
+	else {
 		i2c_reg = GPIOA;
+		/* Use VBT information for CRT DDC if available */
+		if (dev_priv->crt_ddc_bus != -1)
+			i2c_reg = dev_priv->crt_ddc_bus;
+	}
 	intel_output->ddc_bus = intel_i2c_create(dev, i2c_reg, "CRTDDC_A");
 	if (!intel_output->ddc_bus) {
 		dev_printk(KERN_ERR, &dev->pdev->dev, "DDC bus registration "
-- 
GitLab


From 3746b6178070958279010d112703bca9cdc15e0a Mon Sep 17 00:00:00 2001
From: Michael Krufky <mkrufky@kernellabs.com>
Date: Sun, 12 Jul 2009 23:30:14 -0300
Subject: [PATCH 1106/1153] V4L/DVB (12446): sms1xxx: restore GPIO
 functionality for all Hauppauge devices

Previous changesets broke Hauppauge devices and their GPIO configurations.

This changeset restores the LED & LNA functionality.

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/dvb/siano/smsdvb.c | 44 ++++++++++++++++++++++++++++++++
 1 file changed, 44 insertions(+)

diff --git a/drivers/media/dvb/siano/smsdvb.c b/drivers/media/dvb/siano/smsdvb.c
index 3ee1c3902c5..266033ae278 100644
--- a/drivers/media/dvb/siano/smsdvb.c
+++ b/drivers/media/dvb/siano/smsdvb.c
@@ -325,6 +325,16 @@ static int smsdvb_sendrequest_and_wait(struct smsdvb_client_t *client,
 						0 : -ETIME;
 }
 
+static inline int led_feedback(struct smsdvb_client_t *client)
+{
+	if (client->fe_status & FE_HAS_LOCK)
+		return sms_board_led_feedback(client->coredev,
+			(client->sms_stat_dvb.ReceptionData.BER
+			== 0) ? SMS_LED_HI : SMS_LED_LO);
+	else
+		return sms_board_led_feedback(client->coredev, SMS_LED_OFF);
+}
+
 static int smsdvb_read_status(struct dvb_frontend *fe, fe_status_t *stat)
 {
 	struct smsdvb_client_t *client;
@@ -332,6 +342,8 @@ static int smsdvb_read_status(struct dvb_frontend *fe, fe_status_t *stat)
 
 	*stat = client->fe_status;
 
+	led_feedback(client);
+
 	return 0;
 }
 
@@ -342,6 +354,8 @@ static int smsdvb_read_ber(struct dvb_frontend *fe, u32 *ber)
 
 	*ber = client->sms_stat_dvb.ReceptionData.BER;
 
+	led_feedback(client);
+
 	return 0;
 }
 
@@ -359,6 +373,8 @@ static int smsdvb_read_signal_strength(struct dvb_frontend *fe, u16 *strength)
 				(client->sms_stat_dvb.ReceptionData.InBandPwr
 				+ 95) * 3 / 2;
 
+	led_feedback(client);
+
 	return 0;
 }
 
@@ -369,6 +385,8 @@ static int smsdvb_read_snr(struct dvb_frontend *fe, u16 *snr)
 
 	*snr = client->sms_stat_dvb.ReceptionData.SNR;
 
+	led_feedback(client);
+
 	return 0;
 }
 
@@ -379,6 +397,8 @@ static int smsdvb_read_ucblocks(struct dvb_frontend *fe, u32 *ucblocks)
 
 	*ucblocks = client->sms_stat_dvb.ReceptionData.ErrorTSPackets;
 
+	led_feedback(client);
+
 	return 0;
 }
 
@@ -404,6 +424,8 @@ static int smsdvb_set_frontend(struct dvb_frontend *fe,
 		u32		Data[3];
 	} Msg;
 
+	int ret;
+
 	client->fe_status = FE_HAS_SIGNAL;
 	client->event_fe_state = -1;
 	client->event_unc_state = -1;
@@ -426,6 +448,23 @@ static int smsdvb_set_frontend(struct dvb_frontend *fe,
 	case BANDWIDTH_AUTO: return -EOPNOTSUPP;
 	default: return -EINVAL;
 	}
+	/* Disable LNA, if any. An error is returned if no LNA is present */
+	ret = sms_board_lna_control(client->coredev, 0);
+	if (ret == 0) {
+		fe_status_t status;
+
+		/* tune with LNA off at first */
+		ret = smsdvb_sendrequest_and_wait(client, &Msg, sizeof(Msg),
+						  &client->tune_done);
+
+		smsdvb_read_status(fe, &status);
+
+		if (status & FE_HAS_LOCK)
+			return ret;
+
+		/* previous tune didnt lock - enable LNA and tune again */
+		sms_board_lna_control(client->coredev, 1);
+	}
 
 	return smsdvb_sendrequest_and_wait(client, &Msg, sizeof(Msg),
 					   &client->tune_done);
@@ -451,6 +490,8 @@ static int smsdvb_init(struct dvb_frontend *fe)
 	struct smsdvb_client_t *client =
 		container_of(fe, struct smsdvb_client_t, frontend);
 
+	sms_board_power(client->coredev, 1);
+
 	sms_board_dvb3_event(client, DVB3_EVENT_INIT);
 	return 0;
 }
@@ -460,6 +501,9 @@ static int smsdvb_sleep(struct dvb_frontend *fe)
 	struct smsdvb_client_t *client =
 		container_of(fe, struct smsdvb_client_t, frontend);
 
+	sms_board_led_feedback(client->coredev, SMS_LED_OFF);
+	sms_board_power(client->coredev, 0);
+
 	sms_board_dvb3_event(client, DVB3_EVENT_SLEEP);
 
 	return 0;
-- 
GitLab


From f2e26ae7c8c077d001c77b330130f98e42ccad70 Mon Sep 17 00:00:00 2001
From: Mauro Carvalho Chehab <mchehab@redhat.com>
Date: Wed, 12 Aug 2009 20:21:44 -0300
Subject: [PATCH 1107/1153] V4L/DVB (12449): adds webcam for Micron device
 MT9M111 0x143A to em28xx

[mchehab@redhat.com: fix merge conflict and a few CodingStyle issues]
Signed-off-by: Steve Gotthardt <gotthardt@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-cards.c | 40 +++++++++++++++++++++--
 drivers/media/video/em28xx/em28xx.h       |  1 +
 2 files changed, 39 insertions(+), 2 deletions(-)

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index ed281f56594..494560e8231 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -1730,6 +1730,25 @@ static inline void em28xx_set_model(struct em28xx *dev)
 				       EM28XX_I2C_FREQ_100_KHZ;
 }
 
+
+/* FIXME: Should be replaced by a proper mt9m111 driver */
+static int em28xx_initialize_mt9m111(struct em28xx *dev)
+{
+	int i;
+	unsigned char regs[][3] = {
+		{ 0x0d, 0x00, 0x01, },  /* reset and use defaults */
+		{ 0x0d, 0x00, 0x00, },
+		{ 0x0a, 0x00, 0x21, },
+		{ 0x21, 0x04, 0x00, },  /* full readout speed, no row/col skipping */
+	};
+
+	for (i = 0; i < ARRAY_SIZE(regs); i++)
+		i2c_master_send(&dev->i2c_client, &regs[i][0], 3);
+
+	return 0;
+}
+
+
 /* FIXME: Should be replaced by a proper mt9m001 driver */
 static int em28xx_initialize_mt9m001(struct em28xx *dev)
 {
@@ -1758,7 +1777,7 @@ static int em28xx_initialize_mt9m001(struct em28xx *dev)
 
 /* HINT method: webcam I2C chips
  *
- * This method work for webcams with Micron sensors
+ * This method works for webcams with Micron sensors
  */
 static int em28xx_hint_sensor(struct em28xx *dev)
 {
@@ -1804,6 +1823,23 @@ static int em28xx_hint_sensor(struct em28xx *dev)
 		dev->vinctl = 0x00;
 
 		break;
+
+	case 0x143a:    /* MT9M111 as found in the ECS G200 */
+		dev->model = EM2750_BOARD_UNKNOWN;
+		em28xx_set_model(dev);
+
+		sensor_name = "mt9m111";
+		dev->board.xclk = EM28XX_XCLK_FREQUENCY_48MHZ;
+		dev->em28xx_sensor = EM28XX_MT9M111;
+		em28xx_initialize_mt9m111(dev);
+		dev->sensor_xres = 640;
+		dev->sensor_yres = 512;
+
+		dev->vinmode = 0x0a;
+		dev->vinctl = 0x00;
+
+		break;
+
 	case 0x8431:
 		dev->model = EM2750_BOARD_UNKNOWN;
 		em28xx_set_model(dev);
@@ -1820,7 +1856,7 @@ static int em28xx_hint_sensor(struct em28xx *dev)
 
 		break;
 	default:
-		printk("Unknown Micron Sensor 0x%04x\n", be16_to_cpu(version));
+		printk("Unknown Micron Sensor 0x%04x\n", version);
 		return -EINVAL;
 	}
 
diff --git a/drivers/media/video/em28xx/em28xx.h b/drivers/media/video/em28xx/em28xx.h
index 8c2dc38bca9..a2add61f7d5 100644
--- a/drivers/media/video/em28xx/em28xx.h
+++ b/drivers/media/video/em28xx/em28xx.h
@@ -367,6 +367,7 @@ enum em28xx_sensor {
 	EM28XX_NOSENSOR = 0,
 	EM28XX_MT9V011,
 	EM28XX_MT9M001,
+	EM28XX_MT9M111,
 };
 
 enum em28xx_adecoder {
-- 
GitLab


From ef2d12ce12117bb97fa35bbcf677c28e14667efa Mon Sep 17 00:00:00 2001
From: Udi Atar <udia@siano-ms.com>
Date: Sun, 28 Jun 2009 04:22:55 -0300
Subject: [PATCH 1108/1153] V4L/DVB (12450): Siano: Fixed SDIO compilation bugs

Fixed SDIO compilation bugs
Also fixed a memory overrun issue in buffer management.

Signed-off-by: Udi Atar <udia@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/dvb/siano/smssdio.c | 54 +++++++++++++++++--------------
 1 file changed, 30 insertions(+), 24 deletions(-)

diff --git a/drivers/media/dvb/siano/smssdio.c b/drivers/media/dvb/siano/smssdio.c
index dfaa49a53f3..d1d652e7f89 100644
--- a/drivers/media/dvb/siano/smssdio.c
+++ b/drivers/media/dvb/siano/smssdio.c
@@ -46,6 +46,7 @@
 
 #define SMSSDIO_DATA		0x00
 #define SMSSDIO_INT		0x04
+#define SMSSDIO_BLOCK_SIZE	128
 
 static const struct sdio_device_id smssdio_ids[] = {
 	{SDIO_DEVICE(SDIO_VENDOR_ID_SIANO, SDIO_DEVICE_ID_SIANO_STELLAR),
@@ -85,7 +86,8 @@ static int smssdio_sendrequest(void *context, void *buffer, size_t size)
 	sdio_claim_host(smsdev->func);
 
 	while (size >= smsdev->func->cur_blksize) {
-		ret = sdio_write_blocks(smsdev->func, SMSSDIO_DATA, buffer, 1);
+		ret = sdio_memcpy_toio(smsdev->func, SMSSDIO_DATA,
+					buffer, smsdev->func->cur_blksize);
 		if (ret)
 			goto out;
 
@@ -94,8 +96,8 @@ static int smssdio_sendrequest(void *context, void *buffer, size_t size)
 	}
 
 	if (size) {
-		ret = sdio_write_bytes(smsdev->func, SMSSDIO_DATA,
-				       buffer, size);
+		ret = sdio_memcpy_toio(smsdev->func, SMSSDIO_DATA,
+					buffer, size);
 	}
 
 out:
@@ -125,23 +127,23 @@ static void smssdio_interrupt(struct sdio_func *func)
 	 */
 	isr = sdio_readb(func, SMSSDIO_INT, &ret);
 	if (ret) {
-		dev_err(&smsdev->func->dev,
-			"Unable to read interrupt register!\n");
+		sms_err("Unable to read interrupt register!\n");
 		return;
 	}
 
 	if (smsdev->split_cb == NULL) {
 		cb = smscore_getbuffer(smsdev->coredev);
 		if (!cb) {
-			dev_err(&smsdev->func->dev,
-				"Unable to allocate data buffer!\n");
+			sms_err("Unable to allocate data buffer!\n");
 			return;
 		}
 
-		ret = sdio_read_blocks(smsdev->func, cb->p, SMSSDIO_DATA, 1);
+		ret = sdio_memcpy_fromio(smsdev->func,
+					 cb->p,
+					 SMSSDIO_DATA,
+					 SMSSDIO_BLOCK_SIZE);
 		if (ret) {
-			dev_err(&smsdev->func->dev,
-				"Error %d reading initial block!\n", ret);
+			sms_err("Error %d reading initial block!\n", ret);
 			return;
 		}
 
@@ -152,7 +154,10 @@ static void smssdio_interrupt(struct sdio_func *func)
 			return;
 		}
 
-		size = hdr->msgLength - smsdev->func->cur_blksize;
+		if (hdr->msgLength > smsdev->func->cur_blksize)
+			size = hdr->msgLength - smsdev->func->cur_blksize;
+		else
+			size = 0;
 	} else {
 		cb = smsdev->split_cb;
 		hdr = cb->p;
@@ -162,23 +167,24 @@ static void smssdio_interrupt(struct sdio_func *func)
 		smsdev->split_cb = NULL;
 	}
 
-	if (hdr->msgLength > smsdev->func->cur_blksize) {
+	if (size) {
 		void *buffer;
 
-		size = ALIGN(size, 128);
-		buffer = cb->p + hdr->msgLength;
+		buffer = cb->p + (hdr->msgLength - size);
+		size = ALIGN(size, SMSSDIO_BLOCK_SIZE);
 
-		BUG_ON(smsdev->func->cur_blksize != 128);
+		BUG_ON(smsdev->func->cur_blksize != SMSSDIO_BLOCK_SIZE);
 
 		/*
 		 * First attempt to transfer all of it in one go...
 		 */
-		ret = sdio_read_blocks(smsdev->func, buffer,
-				       SMSSDIO_DATA, size / 128);
+		ret = sdio_memcpy_fromio(smsdev->func,
+					 buffer,
+					 SMSSDIO_DATA,
+					 size);
 		if (ret && ret != -EINVAL) {
 			smscore_putbuffer(smsdev->coredev, cb);
-			dev_err(&smsdev->func->dev,
-				"Error %d reading data from card!\n", ret);
+			sms_err("Error %d reading data from card!\n", ret);
 			return;
 		}
 
@@ -191,12 +197,12 @@ static void smssdio_interrupt(struct sdio_func *func)
 		 */
 		if (ret == -EINVAL) {
 			while (size) {
-				ret = sdio_read_blocks(smsdev->func,
-						       buffer, SMSSDIO_DATA, 1);
+				ret = sdio_memcpy_fromio(smsdev->func,
+						  buffer, SMSSDIO_DATA,
+						  smsdev->func->cur_blksize);
 				if (ret) {
 					smscore_putbuffer(smsdev->coredev, cb);
-					dev_err(&smsdev->func->dev,
-						"Error %d reading "
+					sms_err("Error %d reading "
 						"data from card!\n", ret);
 					return;
 				}
@@ -269,7 +275,7 @@ static int smssdio_probe(struct sdio_func *func,
 	if (ret)
 		goto release;
 
-	ret = sdio_set_block_size(func, 128);
+	ret = sdio_set_block_size(func, SMSSDIO_BLOCK_SIZE);
 	if (ret)
 		goto disable;
 
-- 
GitLab


From 31e0ad693fb4e1d1be19dbe1c4f5a1ab9978e810 Mon Sep 17 00:00:00 2001
From: Udi Atar <udia@siano-ms.com>
Date: Thu, 13 Aug 2009 16:30:25 -0300
Subject: [PATCH 1109/1153] V4L/DVB (12451): Update KConfig File to enable SDIO
 and USB interfaces

Update KConfig file to enbale selection of SDIO and USB
interfaces, and add dependancy on relevant modules.

[mchehab@redhat.com: fix merge conflicts, remove default: m, add missing endmenu]

Signed-off-by: Udi Atar <udia@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/dvb/siano/Kconfig  | 40 +++++++++++++++++++-------------
 drivers/media/dvb/siano/Makefile |  9 +++----
 2 files changed, 29 insertions(+), 20 deletions(-)

diff --git a/drivers/media/dvb/siano/Kconfig b/drivers/media/dvb/siano/Kconfig
index 88847d1dcbb..8c1aed77ea3 100644
--- a/drivers/media/dvb/siano/Kconfig
+++ b/drivers/media/dvb/siano/Kconfig
@@ -2,25 +2,33 @@
 # Siano Mobile Silicon Digital TV device configuration
 #
 
-config DVB_SIANO_SMS1XXX
-	tristate "Siano SMS1XXX USB dongle support"
-	depends on DVB_CORE && USB && INPUT
+config SMS_SIANO_MDTV
+	tristate "Siano SMS1xxx based MDTV receiver"
+	depends on DVB_CORE && INPUT
 	---help---
-	  Choose Y here if you have a USB dongle with a SMS1XXX chipset.
+	  Choose Y or M here if you have MDTV receiver with a Siano chipset.
 
-	  To compile this driver as a module, choose M here: the
-	  module will be called sms1xxx.
+	  To compile this driver as a module, choose M here
+	  (The module will be called smsmdtv).
 
-config DVB_SIANO_SMS1XXX_SMS_IDS
-	bool "Enable support for Siano Mobile Silicon default USB IDs"
-	depends on DVB_SIANO_SMS1XXX
-	default y
-	---help---
-	  Choose Y here if you have a USB dongle with a SMS1XXX chipset
-	  that uses Siano Mobile Silicon's default usb vid:pid.
+	  Further documentation on this driver can be found on the WWW
+	  at http://www.siano-ms.com/
+
+if SMS_SIANO_MDTV
+menu "Siano module components"
 
-	  Choose N here if you would prefer to use Siano's external driver.
+# Hardware interfaces support
 
-	  Further documentation on this driver can be found on the WWW at
-	  <http://www.siano-ms.com/>.
+config SMS_USB_DRV
+	tristate "USB interface support"
+	depends on DVB_CORE && USB
+	---help---
+	  Choose if you would like to have Siano's support for USB interface
 
+config SMS_SDIO_DRV
+	tristate "SDIO interface support"
+	depends on DVB_CORE && MMC
+	---help---
+	  Choose if you would like to have Siano's support for SDIO interface
+endmenu
+endif # SMS_SIANO_MDTV
diff --git a/drivers/media/dvb/siano/Makefile b/drivers/media/dvb/siano/Makefile
index c6644d90943..c54140b5ab5 100644
--- a/drivers/media/dvb/siano/Makefile
+++ b/drivers/media/dvb/siano/Makefile
@@ -1,8 +1,9 @@
-sms1xxx-objs := smscoreapi.o sms-cards.o smsendian.o smsir.o
 
-obj-$(CONFIG_DVB_SIANO_SMS1XXX) += sms1xxx.o
-obj-$(CONFIG_DVB_SIANO_SMS1XXX) += smsusb.o
-obj-$(CONFIG_DVB_SIANO_SMS1XXX) += smsdvb.o
+smsmdtv-objs := smscoreapi.o sms-cards.o smsendian.o smsir.o
+
+obj-$(CONFIG_SMS_SIANO_MDTV) += smsmdtv.o smsdvb.o
+obj-$(CONFIG_SMS_USB_DRV) += smsusb.o
+obj-$(CONFIG_SMS_SDIO_DRV) += smssdio.o
 
 EXTRA_CFLAGS += -Idrivers/media/dvb/dvb-core
 
-- 
GitLab


From 7b808924d65a4d1a0332d0043e02e9eb5dafe32b Mon Sep 17 00:00:00 2001
From: Roel Kluin <roel.kluin@gmail.com>
Date: Tue, 11 Aug 2009 08:10:25 -0300
Subject: [PATCH 1110/1153] V4L/DVB (12457): zr364: wrong indexes

The order of indexes is reversed

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/zr364xx.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/video/zr364xx.c b/drivers/media/video/zr364xx.c
index fc976f42f43..2622a6e63da 100644
--- a/drivers/media/video/zr364xx.c
+++ b/drivers/media/video/zr364xx.c
@@ -695,7 +695,7 @@ static int zr364xx_release(struct file *file)
 	for (i = 0; i < 2; i++) {
 		err =
 		    send_control_msg(udev, 1, init[cam->method][i].value,
-				     0, init[i][cam->method].bytes,
+				     0, init[cam->method][i].bytes,
 				     init[cam->method][i].size);
 		if (err < 0) {
 			dev_err(&udev->dev, "error during release sequence\n");
-- 
GitLab


From f4c5e80faba8ae420d7dc5d9237cc1e0262d7386 Mon Sep 17 00:00:00 2001
From: Shine Liu <shinel@foxmail.com>
Date: Thu, 20 Aug 2009 23:49:26 -0300
Subject: [PATCH 1111/1153] V4L/DVB (12495): em28xx: Don't call em28xx_ir_init
 when disable_ir is true

We should call em28xx_ir_init(dev) only when disable_ir is true.

Signed-off-by: Shine Liu <shinel@foxmail.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/em28xx/em28xx-cards.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index 494560e8231..1c2e544eda7 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -2382,7 +2382,9 @@ void em28xx_card_setup(struct em28xx *dev)
 	}
 
 	em28xx_tuner_setup(dev);
-	em28xx_ir_init(dev);
+
+	if(!disable_ir)
+		em28xx_ir_init(dev);
 }
 
 
-- 
GitLab


From b6b85048c059e3f085095e48e12ed3f7a92c88d4 Mon Sep 17 00:00:00 2001
From: Randy Dunlap <randy.dunlap@oracle.com>
Date: Wed, 26 Aug 2009 03:34:16 -0300
Subject: [PATCH 1112/1153] V4L/DVB (12502): gspca - sn9c20x: Fix gscpa sn9c20x
 build errors.

Reported-by: Toralf Forster <toralf.foerster@gmx.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 drivers/media/video/gspca/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/video/gspca/Kconfig b/drivers/media/video/gspca/Kconfig
index 34f46f2bc04..e994dcac43f 100644
--- a/drivers/media/video/gspca/Kconfig
+++ b/drivers/media/video/gspca/Kconfig
@@ -114,7 +114,7 @@ config USB_GSPCA_SN9C20X
 
 config USB_GSPCA_SN9C20X_EVDEV
        bool "Enable evdev support"
-       depends on USB_GSPCA_SN9C20X
+	depends on USB_GSPCA_SN9C20X && INPUT
        ---help---
 	 Say Y here in order to enable evdev support for sn9c20x webcam button.
 
-- 
GitLab


From d95c5b0b905aa9b70521eeb83ad4aea85f5e5fd0 Mon Sep 17 00:00:00 2001
From: Joe Perches <joe@perches.com>
Date: Sun, 16 Aug 2009 20:03:51 -0300
Subject: [PATCH 1113/1153] V4L/DVB (12564a): MAINTAINERS: Update gspca sn9c20x
 name style

To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
---
 MAINTAINERS | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/MAINTAINERS b/MAINTAINERS
index 60299a9a7ad..8dca9d89c6c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2239,8 +2239,7 @@ S:	Maintained
 F:	drivers/media/video/gspca/pac207.c
 
 GSPCA SN9C20X SUBDRIVER
-P:	Brian Johnson
-M:	brijohn@gmail.com
+M:	Brian Johnson <brijohn@gmail.com>
 L:	linux-media@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6.git
 S:	Maintained
-- 
GitLab


From 0f67a611629f84dd0afacd23d422b4b9c2558285 Mon Sep 17 00:00:00 2001
From: Takashi Iwai <tiwai@suse.de>
Date: Mon, 31 Aug 2009 08:12:29 +0200
Subject: [PATCH 1114/1153] ALSA: hda - Add missing mux check for VT1708

In patch_vt1708(), the check of MUX nids is missing and this results in
the -EINVAL error in accessing Input Source mixer element.  Simpliy
adding the call of get_mux_nids() fixes the problem.

Reference: Novell bnc#534904
	https://bugzilla.novell.com/show_bug.cgi?id=534904

Signed-off-by: Takashi Iwai <tiwai@suse.de>
---
 sound/pci/hda/patch_via.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/sound/pci/hda/patch_via.c b/sound/pci/hda/patch_via.c
index 9008b4b013a..e8f10b10cce 100644
--- a/sound/pci/hda/patch_via.c
+++ b/sound/pci/hda/patch_via.c
@@ -1395,6 +1395,7 @@ static int patch_vt1708(struct hda_codec *codec)
 	if (!spec->adc_nids && spec->input_mux) {
 		spec->adc_nids = vt1708_adc_nids;
 		spec->num_adc_nids = ARRAY_SIZE(vt1708_adc_nids);
+		get_mux_nids(codec);
 		spec->mixers[spec->num_mixers] = vt1708_capture_mixer;
 		spec->num_mixers++;
 	}
-- 
GitLab


From a3f730af7e33cea10ea66f05b2565fde1f9512df Mon Sep 17 00:00:00 2001
From: Takashi Iwai <tiwai@suse.de>
Date: Mon, 31 Aug 2009 08:15:26 +0200
Subject: [PATCH 1115/1153] ALSA: hda - Fix MacBookPro 3,1/4,1 quirk with
 ALC889A

This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.

Reference: kernel bug#14078
	http://bugzilla.kernel.org/show_bug.cgi?id=14078

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
---
 sound/pci/hda/patch_realtek.c | 34 ++++++++++++++++++++--------------
 1 file changed, 20 insertions(+), 14 deletions(-)

diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
index 6f683e451f2..30eeb304351 100644
--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -6423,9 +6423,9 @@ static struct hda_verb alc885_mbp_ch2_init[] = {
 };
 
 /*
- * 6ch mode
+ * 4ch mode
  */
-static struct hda_verb alc885_mbp_ch6_init[] = {
+static struct hda_verb alc885_mbp_ch4_init[] = {
 	{ 0x1a, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT },
 	{ 0x1a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
 	{ 0x1a, AC_VERB_SET_CONNECT_SEL, 0x01 },
@@ -6434,9 +6434,9 @@ static struct hda_verb alc885_mbp_ch6_init[] = {
 	{ } /* end */
 };
 
-static struct hda_channel_mode alc885_mbp_6ch_modes[2] = {
+static struct hda_channel_mode alc885_mbp_4ch_modes[2] = {
 	{ 2, alc885_mbp_ch2_init },
-	{ 6, alc885_mbp_ch6_init },
+	{ 4, alc885_mbp_ch4_init },
 };
 
 /*
@@ -6497,10 +6497,11 @@ static struct snd_kcontrol_new alc882_base_mixer[] = {
 };
 
 static struct snd_kcontrol_new alc885_mbp3_mixer[] = {
-	HDA_CODEC_VOLUME("Front Playback Volume", 0x0c, 0x00, HDA_OUTPUT),
-	HDA_BIND_MUTE   ("Front Playback Switch", 0x0c, 0x02, HDA_INPUT),
-	HDA_CODEC_MUTE  ("Speaker Playback Switch", 0x14, 0x00, HDA_OUTPUT),
-	HDA_CODEC_VOLUME("Line-Out Playback Volume", 0x0d, 0x00, HDA_OUTPUT),
+	HDA_CODEC_VOLUME("Speaker Playback Volume", 0x0c, 0x00, HDA_OUTPUT),
+	HDA_BIND_MUTE   ("Speaker Playback Switch", 0x0c, 0x02, HDA_INPUT),
+	HDA_CODEC_VOLUME("Headphone Playback Volume", 0x0e, 0x00, HDA_OUTPUT),
+	HDA_BIND_MUTE   ("Headphone Playback Switch", 0x0e, 0x02, HDA_INPUT),
+	HDA_CODEC_VOLUME("Surround Playback Volume", 0x0d, 0x00, HDA_OUTPUT),
 	HDA_CODEC_VOLUME("Line Playback Volume", 0x0b, 0x02, HDA_INPUT),
 	HDA_CODEC_MUTE  ("Line Playback Switch", 0x0b, 0x02, HDA_INPUT),
 	HDA_CODEC_VOLUME("Mic Playback Volume", 0x0b, 0x00, HDA_INPUT),
@@ -6814,14 +6815,18 @@ static struct hda_verb alc885_mbp3_init_verbs[] = {
 	{0x0d, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
 	{0x0d, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
 	{0x0d, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+	/* HP mixer */
+	{0x0e, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
+	{0x0e, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+	{0x0e, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
 	/* Front Pin: output 0 (0x0c) */
 	{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT},
 	{0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
 	{0x14, AC_VERB_SET_CONNECT_SEL, 0x00},
-	/* HP Pin: output 0 (0x0d) */
+	/* HP Pin: output 0 (0x0e) */
 	{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, 0xc4},
-	{0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE},
-	{0x15, AC_VERB_SET_CONNECT_SEL, 0x00},
+	{0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+	{0x15, AC_VERB_SET_CONNECT_SEL, 0x02},
 	{0x15, AC_VERB_SET_UNSOLICITED_ENABLE, ALC880_HP_EVENT | AC_USRSP_EN},
 	/* Mic (rear) pin: input vref at 80% */
 	{0x18, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80},
@@ -7195,10 +7200,11 @@ static struct alc_config_preset alc882_presets[] = {
 		.mixers = { alc885_mbp3_mixer, alc882_chmode_mixer },
 		.init_verbs = { alc885_mbp3_init_verbs,
 				alc880_gpio1_init_verbs },
-		.num_dacs = ARRAY_SIZE(alc882_dac_nids),
+		.num_dacs = 2,
 		.dac_nids = alc882_dac_nids,
-		.channel_mode = alc885_mbp_6ch_modes,
-		.num_channel_mode = ARRAY_SIZE(alc885_mbp_6ch_modes),
+		.hp_nid = 0x04,
+		.channel_mode = alc885_mbp_4ch_modes,
+		.num_channel_mode = ARRAY_SIZE(alc885_mbp_4ch_modes),
 		.input_mux = &alc882_capture_source,
 		.dig_out_nid = ALC882_DIGOUT_NID,
 		.dig_in_nid = ALC882_DIGIN_NID,
-- 
GitLab


From 60c3be387bb6cd39707d3ec0ebc324a0c96181f8 Mon Sep 17 00:00:00 2001
From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Sun, 30 Aug 2009 14:56:30 +0200
Subject: [PATCH 1116/1153] ata_piix: parallel scanning on PATA needs an extra
 locking

Commit log for commit 517d3cc15b36392e518abab6bacbb72089658313
("[libata] ata_piix: Enable parallel scan") says:

    This patch turns on parallel scanning for the ata_piix driver.
    This driver is used on most netbooks (no AHCI for cheap storage it seems).
    The scan is the dominating time factor in the kernel boot for these
    devices; with this flag it gets cut in half for the device I used
    for testing (eeepc).
    Alan took a look at the driver source and concluded that it ought to be safe
    to do for this driver.  Alan has also checked with the hardware team.

and it is all true but once we put all things together additional
constraints for PATA controllers show up (some hardware registers
have per-host not per-port atomicity) and we risk misprogramming
the controller.

I used the following test to check whether the issue is real:

  @@ -736,8 +736,20 @@ static void piix_set_piomode(struct ata_
   			(timings[pio][1] << 8);
   	}
   	pci_write_config_word(dev, master_port, master_data);
  -	if (is_slave)
  +	if (is_slave) {
  +		if (ap->port_no == 0) {
  +			u8 tmp = slave_data;
  +
  +			while (slave_data == tmp) {
  +				pci_read_config_byte(dev, slave_port, &tmp);
  +				msleep(50);
  +			}
  +
  +			dev_printk(KERN_ERR, &dev->dev, "PATA parallel scan "
  +				   "race detected\n");
  +		}
   		pci_write_config_byte(dev, slave_port, slave_data);
  +	}

   	/* Ensure the UDMA bit is off - it will be turned back on if
   	   UDMA is selected */

and it indeed triggered the error message.

Lets fix all such races by adding an extra locking to ->set_piomode
and ->set_dmamode methods for PATA controllers.

[ Alan: would be better to take the host lock in libata-core for these
  cases so that we fix all the adapters in one swoop.  "Looks fine as a
  temproary quickfix tho" ]

Cc: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 drivers/ata/ata_piix.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)

diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 56b8a3ff128..9ac4e378992 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -664,6 +664,8 @@ static int piix_pata_prereset(struct ata_link *link, unsigned long deadline)
 	return ata_sff_prereset(link, deadline);
 }
 
+static DEFINE_SPINLOCK(piix_lock);
+
 /**
  *	piix_set_piomode - Initialize host controller PATA PIO timings
  *	@ap: Port whose timings we are configuring
@@ -677,8 +679,9 @@ static int piix_pata_prereset(struct ata_link *link, unsigned long deadline)
 
 static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev)
 {
-	unsigned int pio	= adev->pio_mode - XFER_PIO_0;
 	struct pci_dev *dev	= to_pci_dev(ap->host->dev);
+	unsigned long flags;
+	unsigned int pio	= adev->pio_mode - XFER_PIO_0;
 	unsigned int is_slave	= (adev->devno != 0);
 	unsigned int master_port= ap->port_no ? 0x42 : 0x40;
 	unsigned int slave_port	= 0x44;
@@ -708,6 +711,8 @@ static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev)
 	if (adev->class == ATA_DEV_ATA)
 		control |= 4;	/* PPE enable */
 
+	spin_lock_irqsave(&piix_lock, flags);
+
 	/* PIO configuration clears DTE unconditionally.  It will be
 	 * programmed in set_dmamode which is guaranteed to be called
 	 * after set_piomode if any DMA mode is available.
@@ -747,6 +752,8 @@ static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev)
 		udma_enable &= ~(1 << (2 * ap->port_no + adev->devno));
 		pci_write_config_byte(dev, 0x48, udma_enable);
 	}
+
+	spin_unlock_irqrestore(&piix_lock, flags);
 }
 
 /**
@@ -764,6 +771,7 @@ static void piix_set_piomode(struct ata_port *ap, struct ata_device *adev)
 static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, int isich)
 {
 	struct pci_dev *dev	= to_pci_dev(ap->host->dev);
+	unsigned long flags;
 	u8 master_port		= ap->port_no ? 0x42 : 0x40;
 	u16 master_data;
 	u8 speed		= adev->dma_mode;
@@ -777,6 +785,8 @@ static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, in
 			    { 2, 1 },
 			    { 2, 3 }, };
 
+	spin_lock_irqsave(&piix_lock, flags);
+
 	pci_read_config_word(dev, master_port, &master_data);
 	if (ap->udma_mask)
 		pci_read_config_byte(dev, 0x48, &udma_enable);
@@ -867,6 +877,8 @@ static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, in
 	/* Don't scribble on 0x48 if the controller does not support UDMA */
 	if (ap->udma_mask)
 		pci_write_config_byte(dev, 0x48, udma_enable);
+
+	spin_unlock_irqrestore(&piix_lock, flags);
 }
 
 /**
-- 
GitLab


From 1a37f184fa7824982a5f434c06981ec46a66cef7 Mon Sep 17 00:00:00 2001
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Mon, 31 Aug 2009 13:48:16 +1000
Subject: [PATCH 1117/1153] lmb: Also remove __init from lmb_end_of_RAM()
 declaration in lmb.h

My previous patch (commit 4f8ee2c9cc: "lmb: Remove __init from
lmb_end_of_DRAM()") removed __init in lmb.c but missed the fact that it
was also marked as such in the .h

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 include/linux/lmb.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/lmb.h b/include/linux/lmb.h
index c46c89505da..2442e3f3d03 100644
--- a/include/linux/lmb.h
+++ b/include/linux/lmb.h
@@ -51,7 +51,7 @@ extern u64 __init lmb_alloc_base(u64 size,
 extern u64 __init __lmb_alloc_base(u64 size,
 		u64 align, u64 max_addr);
 extern u64 __init lmb_phys_mem_size(void);
-extern u64 __init lmb_end_of_DRAM(void);
+extern u64 lmb_end_of_DRAM(void);
 extern void __init lmb_enforce_memory_limit(u64 memory_limit);
 extern int __init lmb_is_reserved(u64 addr);
 extern int lmb_find(struct lmb_property *res);
-- 
GitLab


From 37d0892c5a94e208cf863e3b7bac014edee4346d Mon Sep 17 00:00:00 2001
From: Ian Kent <raven@themaw.net>
Date: Tue, 1 Sep 2009 11:26:22 +0800
Subject: [PATCH 1118/1153] autofs4 - fix missed case when changing to use
 struct path

In the recent change by Al Viro that changes verious subsystems
to use "struct path" one case was missed in the autofs4 module
which causes mounts to no longer expire.

Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
---
 fs/autofs4/expire.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/autofs4/expire.c b/fs/autofs4/expire.c
index aa39ae83f01..3da18d45348 100644
--- a/fs/autofs4/expire.c
+++ b/fs/autofs4/expire.c
@@ -77,7 +77,7 @@ static int autofs4_mount_busy(struct vfsmount *mnt, struct dentry *dentry)
 	}
 
 	/* Update the expiry counter if fs is busy */
-	if (!may_umount_tree(mnt)) {
+	if (!may_umount_tree(path.mnt)) {
 		struct autofs_info *ino = autofs4_dentry_ino(top);
 		ino->last_used = jiffies;
 		goto done;
-- 
GitLab


From e3e59876e82a5e1a07f365d5474e7b6943524725 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 14:02:10 +0200
Subject: [PATCH 1119/1153] x86/amd-iommu: Dump fault entry on DTE error

This patch adds code to dump the content of the device table
entry which caused an ILLEGAL_DEV_TABLE_ENTRY error from the
IOMMU hardware.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 6c99f503780..364c6de2637 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -138,6 +138,15 @@ static int iommu_has_npcache(struct amd_iommu *iommu)
  *
  ****************************************************************************/
 
+static void dump_dte_entry(u16 devid)
+{
+	int i;
+
+	for (i = 0; i < 8; ++i)
+		pr_err("AMD-Vi: DTE[%d]: %08x\n", i,
+			amd_iommu_dev_table[devid].data[i]);
+}
+
 static void iommu_print_event(void *__evt)
 {
 	u32 *event = __evt;
@@ -155,6 +164,7 @@ static void iommu_print_event(void *__evt)
 		       "address=0x%016llx flags=0x%04x]\n",
 		       PCI_BUS(devid), PCI_SLOT(devid), PCI_FUNC(devid),
 		       address, flags);
+		dump_dte_entry(devid);
 		break;
 	case EVENT_TYPE_IO_FAULT:
 		printk("IO_PAGE_FAULT device=%02x:%02x.%x "
-- 
GitLab


From 945b4ac44e5700acd3d974c176c8ace34b4d2e8e Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 14:25:02 +0200
Subject: [PATCH 1120/1153] x86/amd-iommu: Dump illegal command on
 ILLEGAL_COMMAND_ERROR

This patch adds code to dump the command which caused an
ILLEGAL_COMMAND_ERROR raised by the IOMMU hardware.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 364c6de2637..e62b35f5df1 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -147,6 +147,15 @@ static void dump_dte_entry(u16 devid)
 			amd_iommu_dev_table[devid].data[i]);
 }
 
+static void dump_command(unsigned long phys_addr)
+{
+	struct iommu_cmd *cmd = phys_to_virt(phys_addr);
+	int i;
+
+	for (i = 0; i < 4; ++i)
+		pr_err("AMD-Vi: CMD[%d]: %08x\n", i, cmd->data[i]);
+}
+
 static void iommu_print_event(void *__evt)
 {
 	u32 *event = __evt;
@@ -186,6 +195,7 @@ static void iommu_print_event(void *__evt)
 		break;
 	case EVENT_TYPE_ILL_CMD:
 		printk("ILLEGAL_COMMAND_ERROR address=0x%016llx]\n", address);
+		dump_command(address);
 		break;
 	case EVENT_TYPE_CMD_HARD_ERR:
 		printk("COMMAND_HARDWARE_ERROR address=0x%016llx "
-- 
GitLab


From e394d72aa8b319211b8f947d151d9d50b0fde842 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 15:28:33 +0200
Subject: [PATCH 1121/1153] x86/amd-iommu: Introduce function for iommu-local
 domain flush

This patch introduces a function to flush all domain tlbs
for on one given IOMMU. This is required later to reset the
command buffer on one IOMMU.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 49 +++++++++++++++++++++++++------------
 1 file changed, 33 insertions(+), 16 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index e62b35f5df1..64cc582feb9 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -465,38 +465,55 @@ static void iommu_flush_tlb_pde(struct amd_iommu *iommu, u16 domid)
 }
 
 /*
- * This function is used to flush the IO/TLB for a given protection domain
- * on every IOMMU in the system
+ * This function flushes one domain on one IOMMU
  */
-static void iommu_flush_domain(u16 domid)
+static void flush_domain_on_iommu(struct amd_iommu *iommu, u16 domid)
 {
-	unsigned long flags;
-	struct amd_iommu *iommu;
 	struct iommu_cmd cmd;
-
-	INC_STATS_COUNTER(domain_flush_all);
+	unsigned long flags;
 
 	__iommu_build_inv_iommu_pages(&cmd, CMD_INV_IOMMU_ALL_PAGES_ADDRESS,
 				      domid, 1, 1);
 
-	for_each_iommu(iommu) {
-		spin_lock_irqsave(&iommu->lock, flags);
-		__iommu_queue_command(iommu, &cmd);
-		__iommu_completion_wait(iommu);
-		__iommu_wait_for_completion(iommu);
-		spin_unlock_irqrestore(&iommu->lock, flags);
-	}
+	spin_lock_irqsave(&iommu->lock, flags);
+	__iommu_queue_command(iommu, &cmd);
+	__iommu_completion_wait(iommu);
+	__iommu_wait_for_completion(iommu);
+	spin_unlock_irqrestore(&iommu->lock, flags);
 }
 
-void amd_iommu_flush_all_domains(void)
+static void flush_all_domains_on_iommu(struct amd_iommu *iommu)
 {
 	int i;
 
 	for (i = 1; i < MAX_DOMAIN_ID; ++i) {
 		if (!test_bit(i, amd_iommu_pd_alloc_bitmap))
 			continue;
-		iommu_flush_domain(i);
+		flush_domain_on_iommu(iommu, i);
 	}
+
+}
+
+/*
+ * This function is used to flush the IO/TLB for a given protection domain
+ * on every IOMMU in the system
+ */
+static void iommu_flush_domain(u16 domid)
+{
+	struct amd_iommu *iommu;
+
+	INC_STATS_COUNTER(domain_flush_all);
+
+	for_each_iommu(iommu)
+		flush_domain_on_iommu(iommu, domid);
+}
+
+void amd_iommu_flush_all_domains(void)
+{
+	struct amd_iommu *iommu;
+
+	for_each_iommu(iommu)
+		flush_all_domains_on_iommu(iommu);
 }
 
 void amd_iommu_flush_all_devices(void)
-- 
GitLab


From f2430bd104bec2706315e9e983a9d9f828ff9565 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 26 Aug 2009 12:10:19 +0200
Subject: [PATCH 1122/1153] x86/amd-iommu: Remove some merge helper code

This patch removes some left-overs which where put into the code to
simplify merging code which also depends on changes in other trees.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 6 ------
 1 file changed, 6 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 6c99f503780..70fdef54e06 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -41,9 +41,7 @@ static DEFINE_RWLOCK(amd_iommu_devtable_lock);
 static LIST_HEAD(iommu_pd_list);
 static DEFINE_SPINLOCK(iommu_pd_list_lock);
 
-#ifdef CONFIG_IOMMU_API
 static struct iommu_ops amd_iommu_ops;
-#endif
 
 /*
  * general struct to manage commands send to an IOMMU
@@ -62,10 +60,6 @@ static void dma_ops_reserve_addresses(struct dma_ops_domain *dom,
 				      unsigned long start_page,
 				      unsigned int pages);
 
-#ifndef BUS_NOTIFY_UNBOUND_DRIVER
-#define BUS_NOTIFY_UNBOUND_DRIVER 0x0005
-#endif
-
 #ifdef CONFIG_AMD_IOMMU_STATS
 
 /*
-- 
GitLab


From 4c6f40d4e0f0bba77a5f27eec4e1c6d1c457d324 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Tue, 1 Sep 2009 16:43:58 +0200
Subject: [PATCH 1123/1153] x86/amd-iommu: replace "AMD IOMMU" by "AMD-Vi"

This patch replaces the "AMD IOMMU" printk strings with the
official name for the hardware: "AMD-Vi".

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/include/asm/amd_iommu_types.h |  2 +-
 arch/x86/kernel/amd_iommu.c            |  2 +-
 arch/x86/kernel/amd_iommu_init.c       | 12 ++++++------
 3 files changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h
index 0c878caaa0a..106e1305ef8 100644
--- a/arch/x86/include/asm/amd_iommu_types.h
+++ b/arch/x86/include/asm/amd_iommu_types.h
@@ -198,7 +198,7 @@ extern bool amd_iommu_dump;
 #define DUMP_printk(format, arg...)					\
 	do {								\
 		if (amd_iommu_dump)						\
-			printk(KERN_INFO "AMD IOMMU: " format, ## arg);	\
+			printk(KERN_INFO "AMD-Vi: " format, ## arg);	\
 	} while(0);
 
 /*
diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 70fdef54e06..3e62d783652 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -141,7 +141,7 @@ static void iommu_print_event(void *__evt)
 	int flags = (event[1] >> EVENT_FLAGS_SHIFT) & EVENT_FLAGS_MASK;
 	u64 address = (u64)(((u64)event[3]) << 32) | event[2];
 
-	printk(KERN_ERR "AMD IOMMU: Event logged [");
+	printk(KERN_ERR "AMD-Vi: Event logged [");
 
 	switch (type) {
 	case EVENT_TYPE_ILL_DEV:
diff --git a/arch/x86/kernel/amd_iommu_init.c b/arch/x86/kernel/amd_iommu_init.c
index c1b17e97252..169958ad624 100644
--- a/arch/x86/kernel/amd_iommu_init.c
+++ b/arch/x86/kernel/amd_iommu_init.c
@@ -252,7 +252,7 @@ static void __init iommu_feature_disable(struct amd_iommu *iommu, u8 bit)
 /* Function to enable the hardware */
 static void iommu_enable(struct amd_iommu *iommu)
 {
-	printk(KERN_INFO "AMD IOMMU: Enabling IOMMU at %s cap 0x%hx\n",
+	printk(KERN_INFO "AMD-Vi: Enabling IOMMU at %s cap 0x%hx\n",
 	       dev_name(&iommu->dev->dev), iommu->cap_ptr);
 
 	iommu_feature_enable(iommu, CONTROL_IOMMU_EN);
@@ -902,7 +902,7 @@ static int __init iommu_setup_msi(struct amd_iommu *iommu)
 
 	r = request_irq(iommu->dev->irq, amd_iommu_int_handler,
 			IRQF_SAMPLE_RANDOM,
-			"AMD IOMMU",
+			"AMD-Vi",
 			NULL);
 
 	if (r) {
@@ -1150,7 +1150,7 @@ int __init amd_iommu_init(void)
 
 
 	if (no_iommu) {
-		printk(KERN_INFO "AMD IOMMU disabled by kernel command line\n");
+		printk(KERN_INFO "AMD-Vi disabled by kernel command line\n");
 		return 0;
 	}
 
@@ -1248,16 +1248,16 @@ int __init amd_iommu_init(void)
 
 	enable_iommus();
 
-	printk(KERN_INFO "AMD IOMMU: device isolation ");
+	printk(KERN_INFO "AMD-Vi: device isolation ");
 	if (amd_iommu_isolate)
 		printk("enabled\n");
 	else
 		printk("disabled\n");
 
 	if (amd_iommu_unmap_flush)
-		printk(KERN_INFO "AMD IOMMU: IO/TLB flush on unmap enabled\n");
+		printk(KERN_INFO "AMD-Vi: IO/TLB flush on unmap enabled\n");
 	else
-		printk(KERN_INFO "AMD IOMMU: Lazy IO/TLB flushing enabled\n");
+		printk(KERN_INFO "AMD-Vi: Lazy IO/TLB flushing enabled\n");
 
 out:
 	return ret;
-- 
GitLab


From ae908c22aa2b9f7d4b41bd02d14e473f79c22dd3 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Tue, 1 Sep 2009 16:52:16 +0200
Subject: [PATCH 1124/1153] x86/amd-iommu: Remove redundant 'IOMMU' string

The 'IOMMU: ' prefix is not necessary because the
DUMP_printk macro already prints its own prefix.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu_init.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/kernel/amd_iommu_init.c b/arch/x86/kernel/amd_iommu_init.c
index 169958ad624..264b3ef9dd6 100644
--- a/arch/x86/kernel/amd_iommu_init.c
+++ b/arch/x86/kernel/amd_iommu_init.c
@@ -858,7 +858,7 @@ static int __init init_iommu_all(struct acpi_table_header *table)
 		switch (*p) {
 		case ACPI_IVHD_TYPE:
 
-			DUMP_printk("IOMMU: device: %02x:%02x.%01x cap: %04x "
+			DUMP_printk("device: %02x:%02x.%01x cap: %04x "
 				    "seg: %d flags: %01x info %04x\n",
 				    PCI_BUS(h->devid), PCI_SLOT(h->devid),
 				    PCI_FUNC(h->devid), h->cap_ptr,
-- 
GitLab


From e0faf54ee82bf9c07f0307b4391caad4020bd659 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 15:45:51 +0200
Subject: [PATCH 1125/1153] x86/amd-iommu: fix broken check in
 amd_iommu_flush_all_devices

The amd_iommu_pd_table is indexed by protection domain
number and not by device id. So this check is broken and
must be removed.

Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 3e62d783652..009d722af00 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -479,8 +479,6 @@ void amd_iommu_flush_all_devices(void)
 	int i;
 
 	for (i = 0; i <= amd_iommu_last_bdf; ++i) {
-		if (amd_iommu_pd_table[i] == NULL)
-			continue;
 
 		iommu = amd_iommu_rlookup_table[i];
 		if (!iommu)
-- 
GitLab


From d586d7852ccd0cecb502bf4809f827e60c486af0 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 15:39:23 +0200
Subject: [PATCH 1126/1153] x86/amd-iommu: Add function to flush all DTEs on
 one IOMMU

This function flushes all DTE entries on one IOMMU for all
devices behind this IOMMU. This is required for command
buffer resetting later.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 64cc582feb9..2dc093370d2 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -516,6 +516,19 @@ void amd_iommu_flush_all_domains(void)
 		flush_all_domains_on_iommu(iommu);
 }
 
+static void flush_all_devices_for_iommu(struct amd_iommu *iommu)
+{
+	int i;
+
+	for (i = 0; i <= amd_iommu_last_bdf; ++i) {
+		if (iommu != amd_iommu_rlookup_table[i])
+			continue;
+
+		iommu_queue_inv_dev_entry(iommu, i);
+		iommu_completion_wait(iommu);
+	}
+}
+
 void amd_iommu_flush_all_devices(void)
 {
 	struct amd_iommu *iommu;
-- 
GitLab


From 93f1cc67cf3196174412adca87321b25c1c986b0 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 14:50:20 +0200
Subject: [PATCH 1127/1153] x86/amd-iommu: Add reset function for command
 buffers

This patch factors parts of the command buffer
initialization code into a seperate function which can be
used to reset the command buffer later.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/include/asm/amd_iommu_types.h |  3 +++
 arch/x86/kernel/amd_iommu_init.c       | 20 +++++++++++++++-----
 2 files changed, 18 insertions(+), 5 deletions(-)

diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h
index 0c878caaa0a..c54bc979dc1 100644
--- a/arch/x86/include/asm/amd_iommu_types.h
+++ b/arch/x86/include/asm/amd_iommu_types.h
@@ -457,4 +457,7 @@ static inline void amd_iommu_stats_init(void) { }
 
 #endif /* CONFIG_AMD_IOMMU_STATS */
 
+/* some function prototypes */
+extern void amd_iommu_reset_cmd_buffer(struct amd_iommu *iommu);
+
 #endif /* _ASM_X86_AMD_IOMMU_TYPES_H */
diff --git a/arch/x86/kernel/amd_iommu_init.c b/arch/x86/kernel/amd_iommu_init.c
index c1b17e97252..1752afef948 100644
--- a/arch/x86/kernel/amd_iommu_init.c
+++ b/arch/x86/kernel/amd_iommu_init.c
@@ -434,6 +434,20 @@ static u8 * __init alloc_command_buffer(struct amd_iommu *iommu)
 	return cmd_buf;
 }
 
+/*
+ * This function resets the command buffer if the IOMMU stopped fetching
+ * commands from it.
+ */
+void amd_iommu_reset_cmd_buffer(struct amd_iommu *iommu)
+{
+	iommu_feature_disable(iommu, CONTROL_CMDBUF_EN);
+
+	writel(0x00, iommu->mmio_base + MMIO_CMD_HEAD_OFFSET);
+	writel(0x00, iommu->mmio_base + MMIO_CMD_TAIL_OFFSET);
+
+	iommu_feature_enable(iommu, CONTROL_CMDBUF_EN);
+}
+
 /*
  * This function writes the command buffer address to the hardware and
  * enables it.
@@ -450,11 +464,7 @@ static void iommu_enable_command_buffer(struct amd_iommu *iommu)
 	memcpy_toio(iommu->mmio_base + MMIO_CMD_BUF_OFFSET,
 		    &entry, sizeof(entry));
 
-	/* set head and tail to zero manually */
-	writel(0x00, iommu->mmio_base + MMIO_CMD_HEAD_OFFSET);
-	writel(0x00, iommu->mmio_base + MMIO_CMD_TAIL_OFFSET);
-
-	iommu_feature_enable(iommu, CONTROL_CMDBUF_EN);
+	amd_iommu_reset_cmd_buffer(iommu);
 }
 
 static void __init free_command_buffer(struct amd_iommu *iommu)
-- 
GitLab


From a345b23b79f1900e7d87c3165182504419180de4 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 15:01:43 +0200
Subject: [PATCH 1128/1153] x86/amd-iommu: Reset command buffer on
 ILLEGAL_COMMAND_ERROR

On an ILLEGAL_COMMAND_ERROR the IOMMU stops executing
further commands. This patch changes the code to handle this
case better by resetting the command buffer in the IOMMU.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 2dc093370d2..2333d615f5e 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -61,6 +61,7 @@ static u64* alloc_pte(struct protection_domain *dom,
 static void dma_ops_reserve_addresses(struct dma_ops_domain *dom,
 				      unsigned long start_page,
 				      unsigned int pages);
+static void reset_iommu_command_buffer(struct amd_iommu *iommu);
 
 #ifndef BUS_NOTIFY_UNBOUND_DRIVER
 #define BUS_NOTIFY_UNBOUND_DRIVER 0x0005
@@ -156,7 +157,7 @@ static void dump_command(unsigned long phys_addr)
 		pr_err("AMD-Vi: CMD[%d]: %08x\n", i, cmd->data[i]);
 }
 
-static void iommu_print_event(void *__evt)
+static void iommu_print_event(struct amd_iommu *iommu, void *__evt)
 {
 	u32 *event = __evt;
 	int type  = (event[1] >> EVENT_TYPE_SHIFT)  & EVENT_TYPE_MASK;
@@ -195,6 +196,7 @@ static void iommu_print_event(void *__evt)
 		break;
 	case EVENT_TYPE_ILL_CMD:
 		printk("ILLEGAL_COMMAND_ERROR address=0x%016llx]\n", address);
+		reset_iommu_command_buffer(iommu);
 		dump_command(address);
 		break;
 	case EVENT_TYPE_CMD_HARD_ERR:
@@ -229,7 +231,7 @@ static void iommu_poll_events(struct amd_iommu *iommu)
 	tail = readl(iommu->mmio_base + MMIO_EVT_TAIL_OFFSET);
 
 	while (head != tail) {
-		iommu_print_event(iommu->evt_buf + head);
+		iommu_print_event(iommu, iommu->evt_buf + head);
 		head = (head + EVENT_ENTRY_SIZE) % iommu->evt_buf_size;
 	}
 
@@ -547,6 +549,15 @@ void amd_iommu_flush_all_devices(void)
 	}
 }
 
+static void reset_iommu_command_buffer(struct amd_iommu *iommu)
+{
+	pr_err("AMD-Vi: Resetting IOMMU command buffer\n");
+
+	amd_iommu_reset_cmd_buffer(iommu);
+	flush_all_devices_for_iommu(iommu);
+	flush_all_domains_on_iommu(iommu);
+}
+
 /****************************************************************************
  *
  * The functions below are used the create the page table mappings for
-- 
GitLab


From b26e81b871bd18184968f0bb3f12945906eadfce Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 15:08:09 +0200
Subject: [PATCH 1129/1153] x86/amd-iommu: Panic if IOMMU command buffer reset
 fails

To prevent the driver from doing recursive command buffer
resets, just panic when that recursion happens.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/include/asm/amd_iommu_types.h | 3 +++
 arch/x86/kernel/amd_iommu.c            | 7 +++++++
 2 files changed, 10 insertions(+)

diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h
index c54bc979dc1..e676746a4a3 100644
--- a/arch/x86/include/asm/amd_iommu_types.h
+++ b/arch/x86/include/asm/amd_iommu_types.h
@@ -337,6 +337,9 @@ struct amd_iommu {
 	/* if one, we need to send a completion wait command */
 	bool need_sync;
 
+	/* becomes true if a command buffer reset is running */
+	bool reset_in_progress;
+
 	/* default dma_ops domain for that IOMMU */
 	struct dma_ops_domain *default_dom;
 };
diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 2333d615f5e..b62a2f64dfc 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -553,9 +553,16 @@ static void reset_iommu_command_buffer(struct amd_iommu *iommu)
 {
 	pr_err("AMD-Vi: Resetting IOMMU command buffer\n");
 
+	if (iommu->reset_in_progress)
+		panic("AMD-Vi: ILLEGAL_COMMAND_ERROR while resetting command buffer\n");
+
+	iommu->reset_in_progress = true;
+
 	amd_iommu_reset_cmd_buffer(iommu);
 	flush_all_devices_for_iommu(iommu);
 	flush_all_domains_on_iommu(iommu);
+
+	iommu->reset_in_progress = false;
 }
 
 /****************************************************************************
-- 
GitLab


From 6a1eddd2f951656a6abbd42e2cddc2267c4a639d Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 15:15:10 +0200
Subject: [PATCH 1130/1153] x86/amd-iommu: Reset command buffer if wait loop
 fails

Instead of a panic on an comletion wait loop failure, try to
recover from that event from resetting the command buffer.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index b62a2f64dfc..cfca80bfe75 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -318,8 +318,11 @@ static void __iommu_wait_for_completion(struct amd_iommu *iommu)
 	status &= ~MMIO_STATUS_COM_WAIT_INT_MASK;
 	writel(status, iommu->mmio_base + MMIO_STATUS_OFFSET);
 
-	if (unlikely(i == EXIT_LOOP_COUNT))
-		panic("AMD IOMMU: Completion wait loop failed\n");
+	if (unlikely(i == EXIT_LOOP_COUNT)) {
+		spin_unlock(&iommu->lock);
+		reset_iommu_command_buffer(iommu);
+		spin_lock(&iommu->lock);
+	}
 }
 
 /*
-- 
GitLab


From 9355a08186e52b7c120adea91c984923b54efa10 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 14:24:08 +0200
Subject: [PATCH 1131/1153] x86/amd-iommu: Make fetch_pte aware of dynamic
 mapping levels

This patch changes the fetch_pte function in the AMD IOMMU
driver to support dynamic mapping levels.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/include/asm/amd_iommu_types.h |  9 +++++++++
 arch/x86/kernel/amd_iommu.c            | 24 +++++++++++++-----------
 2 files changed, 22 insertions(+), 11 deletions(-)

diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h
index 0c878caaa0a..7fce4ef77bd 100644
--- a/arch/x86/include/asm/amd_iommu_types.h
+++ b/arch/x86/include/asm/amd_iommu_types.h
@@ -146,12 +146,21 @@
 #define PAGE_MODE_1_LEVEL 0x01
 #define PAGE_MODE_2_LEVEL 0x02
 #define PAGE_MODE_3_LEVEL 0x03
+#define PAGE_MODE_4_LEVEL 0x04
+#define PAGE_MODE_5_LEVEL 0x05
+#define PAGE_MODE_6_LEVEL 0x06
 
 #define IOMMU_PDE_NL_0   0x000ULL
 #define IOMMU_PDE_NL_1   0x200ULL
 #define IOMMU_PDE_NL_2   0x400ULL
 #define IOMMU_PDE_NL_3   0x600ULL
 
+#define PM_LEVEL_SHIFT(x)	(12 + ((x) * 9))
+#define PM_LEVEL_SIZE(x)	(((x) < 6) ? \
+				  ((1ULL << PM_LEVEL_SHIFT((x))) - 1): \
+				   (0xffffffffffffffffULL))
+#define PM_LEVEL_INDEX(x, a)	(((a) >> PM_LEVEL_SHIFT((x))) & 0x1ffULL)
+
 #define IOMMU_PTE_L2_INDEX(address) (((address) >> 30) & 0x1ffULL)
 #define IOMMU_PTE_L1_INDEX(address) (((address) >> 21) & 0x1ffULL)
 #define IOMMU_PTE_L0_INDEX(address) (((address) >> 12) & 0x1ffULL)
diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 6c99f503780..29bcd358b6c 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -61,6 +61,8 @@ static u64* alloc_pte(struct protection_domain *dom,
 static void dma_ops_reserve_addresses(struct dma_ops_domain *dom,
 				      unsigned long start_page,
 				      unsigned int pages);
+static u64 *fetch_pte(struct protection_domain *domain,
+		      unsigned long address);
 
 #ifndef BUS_NOTIFY_UNBOUND_DRIVER
 #define BUS_NOTIFY_UNBOUND_DRIVER 0x0005
@@ -670,24 +672,24 @@ static int init_unity_mappings_for_device(struct dma_ops_domain *dma_dom,
  * This function checks if there is a PTE for a given dma address. If
  * there is one, it returns the pointer to it.
  */
-static u64* fetch_pte(struct protection_domain *domain,
+static u64 *fetch_pte(struct protection_domain *domain,
 		      unsigned long address)
 {
+	int level;
 	u64 *pte;
 
-	pte = &domain->pt_root[IOMMU_PTE_L2_INDEX(address)];
+	level =  domain->mode - 1;
+	pte   = &domain->pt_root[PM_LEVEL_INDEX(level, address)];
 
-	if (!IOMMU_PTE_PRESENT(*pte))
-		return NULL;
+	while (level > 0) {
+		if (!IOMMU_PTE_PRESENT(*pte))
+			return NULL;
 
-	pte = IOMMU_PTE_PAGE(*pte);
-	pte = &pte[IOMMU_PTE_L1_INDEX(address)];
+		level -= 1;
 
-	if (!IOMMU_PTE_PRESENT(*pte))
-		return NULL;
-
-	pte = IOMMU_PTE_PAGE(*pte);
-	pte = &pte[IOMMU_PTE_L0_INDEX(address)];
+		pte = IOMMU_PTE_PAGE(*pte);
+		pte = &pte[PM_LEVEL_INDEX(level, address)];
+	}
 
 	return pte;
 }
-- 
GitLab


From 38a76eeeafb251bf67d143a34b37a8105cff302e Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 17:02:47 +0200
Subject: [PATCH 1132/1153] x86/amd-iommu: Use fetch_pte in iommu_unmap_page

Instead of reimplementing existing logic use fetch_pte to
walk the page table in iommu_unmap_page.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 19 +++----------------
 1 file changed, 3 insertions(+), 16 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 29bcd358b6c..5e527989999 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -546,23 +546,10 @@ static int iommu_map_page(struct protection_domain *dom,
 static void iommu_unmap_page(struct protection_domain *dom,
 			     unsigned long bus_addr)
 {
-	u64 *pte;
-
-	pte = &dom->pt_root[IOMMU_PTE_L2_INDEX(bus_addr)];
-
-	if (!IOMMU_PTE_PRESENT(*pte))
-		return;
-
-	pte = IOMMU_PTE_PAGE(*pte);
-	pte = &pte[IOMMU_PTE_L1_INDEX(bus_addr)];
-
-	if (!IOMMU_PTE_PRESENT(*pte))
-		return;
-
-	pte = IOMMU_PTE_PAGE(*pte);
-	pte = &pte[IOMMU_PTE_L1_INDEX(bus_addr)];
+	u64 *pte = fetch_pte(dom, bus_addr);
 
-	*pte = 0;
+	if (pte)
+		*pte = 0;
 }
 
 /*
-- 
GitLab


From a6d41a4027b758a9473197a78fab45afb31003aa Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 17:08:55 +0200
Subject: [PATCH 1133/1153] x86/amd-iommu: Use fetch_pte in
 amd_iommu_iova_to_phys

Don't reimplement the page table walker in this function.
Use the generic one.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 16 ++--------------
 1 file changed, 2 insertions(+), 14 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 5e527989999..4a54366d422 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -2140,21 +2140,9 @@ static phys_addr_t amd_iommu_iova_to_phys(struct iommu_domain *dom,
 	phys_addr_t paddr;
 	u64 *pte;
 
-	pte = &domain->pt_root[IOMMU_PTE_L2_INDEX(iova)];
+	pte = fetch_pte(domain, iova);
 
-	if (!IOMMU_PTE_PRESENT(*pte))
-		return 0;
-
-	pte = IOMMU_PTE_PAGE(*pte);
-	pte = &pte[IOMMU_PTE_L1_INDEX(iova)];
-
-	if (!IOMMU_PTE_PRESENT(*pte))
-		return 0;
-
-	pte = IOMMU_PTE_PAGE(*pte);
-	pte = &pte[IOMMU_PTE_L0_INDEX(iova)];
-
-	if (!IOMMU_PTE_PRESENT(*pte))
+	if (!pte || !IOMMU_PTE_PRESENT(*pte))
 		return 0;
 
 	paddr  = *pte & IOMMU_PAGE_MASK;
-- 
GitLab


From 6a0dbcbe4e612fbc9d73cd4dde8ebef19295058a Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 15:41:59 +0200
Subject: [PATCH 1134/1153] x86/amd-iommu: Add a gneric version of
 amd_iommu_flush_all_devices

This patch adds a generic variant of
amd_iommu_flush_all_devices function which flushes only the
DTEs for a given protection domain.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 4a54366d422..5265dd17eb5 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -481,13 +481,14 @@ void amd_iommu_flush_all_domains(void)
 	}
 }
 
-void amd_iommu_flush_all_devices(void)
+static void flush_devices_by_domain(struct protection_domain *domain)
 {
 	struct amd_iommu *iommu;
 	int i;
 
 	for (i = 0; i <= amd_iommu_last_bdf; ++i) {
-		if (amd_iommu_pd_table[i] == NULL)
+		if ((domain == NULL && amd_iommu_pd_table[i] == NULL) ||
+		    (amd_iommu_pd_table[i] != domain))
 			continue;
 
 		iommu = amd_iommu_rlookup_table[i];
@@ -499,6 +500,11 @@ void amd_iommu_flush_all_devices(void)
 	}
 }
 
+void amd_iommu_flush_all_devices(void)
+{
+	flush_devices_by_domain(NULL);
+}
+
 /****************************************************************************
  *
  * The functions below are used the create the page table mappings for
-- 
GitLab


From 407d733e30a97daf5ea6f9eb5f9ebbd42a0a9ef2 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 16:07:00 +0200
Subject: [PATCH 1135/1153] x86/amd-iommu: Introduce set_dte_entry function

This function factors out some logic of attach_device to a
seperate function. This new function will be used to update
device table entries when necessary.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 27 +++++++++++++++++----------
 1 file changed, 17 insertions(+), 10 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 5265dd17eb5..0fab1f1d135 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -1058,18 +1058,10 @@ static struct protection_domain *domain_for_device(u16 devid)
 	return dom;
 }
 
-/*
- * If a device is not yet associated with a domain, this function does
- * assigns it visible for the hardware
- */
-static void attach_device(struct amd_iommu *iommu,
-			  struct protection_domain *domain,
-			  u16 devid)
+static void set_dte_entry(u16 devid, struct protection_domain *domain)
 {
-	unsigned long flags;
 	u64 pte_root = virt_to_phys(domain->pt_root);
-
-	domain->dev_cnt += 1;
+	unsigned long flags;
 
 	pte_root |= (domain->mode & DEV_ENTRY_MODE_MASK)
 		    << DEV_ENTRY_MODE_SHIFT;
@@ -1082,6 +1074,21 @@ static void attach_device(struct amd_iommu *iommu,
 
 	amd_iommu_pd_table[devid] = domain;
 	write_unlock_irqrestore(&amd_iommu_devtable_lock, flags);
+}
+
+/*
+ * If a device is not yet associated with a domain, this function does
+ * assigns it visible for the hardware
+ */
+static void attach_device(struct amd_iommu *iommu,
+			  struct protection_domain *domain,
+			  u16 devid)
+{
+	/* set the DTE entry */
+	set_dte_entry(devid, domain);
+
+	/* increase reference counter */
+	domain->dev_cnt += 1;
 
        /*
         * We might boot into a crash-kernel here. The crashed kernel
-- 
GitLab


From 04bfdd8406099fca2e6b8844748c4d6c5eba8c8d Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 16:00:23 +0200
Subject: [PATCH 1136/1153] x86/amd-iommu: Flush domains if address space size
 was increased

Thist patch introduces the update_domain function which
propagates the larger address space of a protection domain
to the device table and flushes all relevant DTEs and the
domain TLB.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/include/asm/amd_iommu_types.h |  1 +
 arch/x86/kernel/amd_iommu.c            | 32 ++++++++++++++++++++++++++
 2 files changed, 33 insertions(+)

diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h
index 7fce4ef77bd..97f3d09d3be 100644
--- a/arch/x86/include/asm/amd_iommu_types.h
+++ b/arch/x86/include/asm/amd_iommu_types.h
@@ -235,6 +235,7 @@ struct protection_domain {
 	int mode;		/* paging mode (0-6 levels) */
 	u64 *pt_root;		/* page table root pointer */
 	unsigned long flags;	/* flags to find out type of domain */
+	bool updated;		/* complete domain flush required */
 	unsigned dev_cnt;	/* devices assigned to this domain */
 	void *priv;		/* private data */
 };
diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 0fab1f1d135..5eab6a84b9c 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -63,6 +63,7 @@ static void dma_ops_reserve_addresses(struct dma_ops_domain *dom,
 				      unsigned int pages);
 static u64 *fetch_pte(struct protection_domain *domain,
 		      unsigned long address);
+static void update_domain(struct protection_domain *domain);
 
 #ifndef BUS_NOTIFY_UNBOUND_DRIVER
 #define BUS_NOTIFY_UNBOUND_DRIVER 0x0005
@@ -546,6 +547,8 @@ static int iommu_map_page(struct protection_domain *dom,
 
 	*pte = __pte;
 
+	update_domain(dom);
+
 	return 0;
 }
 
@@ -762,9 +765,13 @@ static int alloc_new_range(struct amd_iommu *iommu,
 		dma_ops_reserve_addresses(dma_dom, i << PAGE_SHIFT, 1);
 	}
 
+	update_domain(&dma_dom->domain);
+
 	return 0;
 
 out_free:
+	update_domain(&dma_dom->domain);
+
 	free_page((unsigned long)dma_dom->aperture[index]->bitmap);
 
 	kfree(dma_dom->aperture[index]);
@@ -1294,6 +1301,29 @@ static int get_device_resources(struct device *dev,
 	return 1;
 }
 
+static void update_device_table(struct protection_domain *domain)
+{
+	int i;
+
+	for (i = 0; i <= amd_iommu_last_bdf; ++i) {
+		if (amd_iommu_pd_table[i] != domain)
+			continue;
+		set_dte_entry(i, domain);
+	}
+}
+
+static void update_domain(struct protection_domain *domain)
+{
+	if (!domain->updated)
+		return;
+
+	update_device_table(domain);
+	flush_devices_by_domain(domain);
+	iommu_flush_domain(domain->id);
+
+	domain->updated = false;
+}
+
 /*
  * If the pte_page is not yet allocated this function is called
  */
@@ -1351,6 +1381,8 @@ static u64* dma_ops_get_pte(struct dma_ops_domain *dom,
 	} else
 		pte += IOMMU_PTE_L0_INDEX(address);
 
+	update_domain(&dom->domain);
+
 	return pte;
 }
 
-- 
GitLab


From 50020fb6324465e478d6c8cdbf3c695f0a60358d Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 15:38:40 +0200
Subject: [PATCH 1137/1153] x86/amd-iommu: Introduce increase_address_space
 function

This function will be used to increase the address space
size of a protection domain.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/include/asm/amd_iommu_types.h |  4 ++++
 arch/x86/kernel/amd_iommu.c            | 27 ++++++++++++++++++++++++++
 2 files changed, 31 insertions(+)

diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h
index 97f3d09d3be..1b4b3d6c9f0 100644
--- a/arch/x86/include/asm/amd_iommu_types.h
+++ b/arch/x86/include/asm/amd_iommu_types.h
@@ -160,6 +160,10 @@
 				  ((1ULL << PM_LEVEL_SHIFT((x))) - 1): \
 				   (0xffffffffffffffffULL))
 #define PM_LEVEL_INDEX(x, a)	(((a) >> PM_LEVEL_SHIFT((x))) & 0x1ffULL)
+#define PM_LEVEL_ENC(x)		(((x) << 9) & 0xe00ULL)
+#define PM_LEVEL_PDE(x, a)	((a) | PM_LEVEL_ENC((x)) | \
+				 IOMMU_PTE_P | IOMMU_PTE_IR | IOMMU_PTE_IW)
+
 
 #define IOMMU_PTE_L2_INDEX(address) (((address) >> 30) & 0x1ffULL)
 #define IOMMU_PTE_L1_INDEX(address) (((address) >> 21) & 0x1ffULL)
diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 5eab6a84b9c..fc97b51f028 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -1324,6 +1324,33 @@ static void update_domain(struct protection_domain *domain)
 	domain->updated = false;
 }
 
+/*
+ * This function is used to add another level to an IO page table. Adding
+ * another level increases the size of the address space by 9 bits to a size up
+ * to 64 bits.
+ */
+static bool increase_address_space(struct protection_domain *domain,
+				   gfp_t gfp)
+{
+	u64 *pte;
+
+	if (domain->mode == PAGE_MODE_6_LEVEL)
+		/* address space already 64 bit large */
+		return false;
+
+	pte = (void *)get_zeroed_page(gfp);
+	if (!pte)
+		return false;
+
+	*pte             = PM_LEVEL_PDE(domain->mode,
+					virt_to_phys(domain->pt_root));
+	domain->pt_root  = pte;
+	domain->mode    += 1;
+	domain->updated  = true;
+
+	return true;
+}
+
 /*
  * If the pte_page is not yet allocated this function is called
  */
-- 
GitLab


From 8bc3e127421bf3b735edbde05135892c12c5f615 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 16:48:40 +0200
Subject: [PATCH 1138/1153] x86/amd-iommu: Change alloc_pte to support 64 bit
 address space

This patch changes the alloc_pte function to be able to map
pages into the whole 64 bit address space supported by AMD
IOMMU hardware from the old limit of 2**39 bytes.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 44 +++++++++++++++++--------------------
 1 file changed, 20 insertions(+), 24 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index fc97b51f028..3be2b61fc31 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -55,7 +55,7 @@ struct iommu_cmd {
 static int dma_ops_unity_map(struct dma_ops_domain *dma_dom,
 			     struct unity_map_entry *e);
 static struct dma_ops_domain *find_protection_domain(u16 devid);
-static u64* alloc_pte(struct protection_domain *dom,
+static u64 *alloc_pte(struct protection_domain *domain,
 		      unsigned long address, u64
 		      **pte_page, gfp_t gfp);
 static void dma_ops_reserve_addresses(struct dma_ops_domain *dom,
@@ -1351,39 +1351,35 @@ static bool increase_address_space(struct protection_domain *domain,
 	return true;
 }
 
-/*
- * If the pte_page is not yet allocated this function is called
- */
-static u64* alloc_pte(struct protection_domain *dom,
+static u64 *alloc_pte(struct protection_domain *domain,
 		      unsigned long address, u64 **pte_page, gfp_t gfp)
 {
 	u64 *pte, *page;
+	int level;
 
-	pte = &dom->pt_root[IOMMU_PTE_L2_INDEX(address)];
+	while (address > PM_LEVEL_SIZE(domain->mode))
+		increase_address_space(domain, gfp);
 
-	if (!IOMMU_PTE_PRESENT(*pte)) {
-		page = (u64 *)get_zeroed_page(gfp);
-		if (!page)
-			return NULL;
-		*pte = IOMMU_L2_PDE(virt_to_phys(page));
-	}
+	level =  domain->mode - 1;
+	pte   = &domain->pt_root[PM_LEVEL_INDEX(level, address)];
 
-	pte = IOMMU_PTE_PAGE(*pte);
-	pte = &pte[IOMMU_PTE_L1_INDEX(address)];
+	while (level > 0) {
+		if (!IOMMU_PTE_PRESENT(*pte)) {
+			page = (u64 *)get_zeroed_page(gfp);
+			if (!page)
+				return NULL;
+			*pte = PM_LEVEL_PDE(level, virt_to_phys(page));
+		}
 
-	if (!IOMMU_PTE_PRESENT(*pte)) {
-		page = (u64 *)get_zeroed_page(gfp);
-		if (!page)
-			return NULL;
-		*pte = IOMMU_L1_PDE(virt_to_phys(page));
-	}
+		level -= 1;
 
-	pte = IOMMU_PTE_PAGE(*pte);
+		pte = IOMMU_PTE_PAGE(*pte);
 
-	if (pte_page)
-		*pte_page = pte;
+		if (pte_page && level == 0)
+			*pte_page = pte;
 
-	pte = &pte[IOMMU_PTE_L0_INDEX(address)];
+		pte = &pte[PM_LEVEL_INDEX(level, address)];
+	}
 
 	return pte;
 }
-- 
GitLab


From 8c8c143cdc95ebe50fd962917556e25e8912997b Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 17:30:00 +0200
Subject: [PATCH 1139/1153] x86/amd-iommu: Remove last usages of
 IOMMU_PTE_L0_INDEX

This change allows to remove these old macros later.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 3be2b61fc31..ebc1c844392 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -1402,7 +1402,7 @@ static u64* dma_ops_get_pte(struct dma_ops_domain *dom,
 		pte = alloc_pte(&dom->domain, address, &pte_page, GFP_ATOMIC);
 		aperture->pte_pages[APERTURE_PAGE_INDEX(address)] = pte_page;
 	} else
-		pte += IOMMU_PTE_L0_INDEX(address);
+		pte += PM_LEVEL_INDEX(0, address);
 
 	update_domain(&dom->domain);
 
@@ -1466,7 +1466,7 @@ static void dma_ops_domain_unmap(struct amd_iommu *iommu,
 	if (!pte)
 		return;
 
-	pte += IOMMU_PTE_L0_INDEX(address);
+	pte += PM_LEVEL_INDEX(0, address);
 
 	WARN_ON(!*pte);
 
-- 
GitLab


From bad1cac28a707c69301a4d0612da9ccbecd51953 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 16:52:23 +0200
Subject: [PATCH 1140/1153] x86/amd-iommu: Remove bus_addr check in
 iommu_map_page

The driver now supports full 64 bit device address spaces.
So this check is not longer required.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index ebc1c844392..6ffb3e63765 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -530,8 +530,7 @@ static int iommu_map_page(struct protection_domain *dom,
 	bus_addr  = PAGE_ALIGN(bus_addr);
 	phys_addr = PAGE_ALIGN(phys_addr);
 
-	/* only support 512GB address spaces for now */
-	if (bus_addr > IOMMU_MAP_SIZE_L3 || !(prot & IOMMU_PROT_MASK))
+	if (!(prot & IOMMU_PROT_MASK))
 		return -EINVAL;
 
 	pte = alloc_pte(dom, bus_addr, NULL, GFP_KERNEL);
-- 
GitLab


From 8f7a017ce05ed4522809448e169daa44fe6edeb1 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 16:55:24 +0200
Subject: [PATCH 1141/1153] x86/amd-iommu: Use 2-level page tables for dma_ops
 domains

The driver now supports a dynamic number of levels for IO
page tables. This allows to reduce the number of levels for
dma_ops domains by one because a dma_ops domain has usually
an address space size between 128MB and 4G.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 6ffb3e63765..addf6588c36 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -1010,7 +1010,7 @@ static struct dma_ops_domain *dma_ops_domain_alloc(struct amd_iommu *iommu)
 	dma_dom->domain.id = domain_id_alloc();
 	if (dma_dom->domain.id == 0)
 		goto free_dma_dom;
-	dma_dom->domain.mode = PAGE_MODE_3_LEVEL;
+	dma_dom->domain.mode = PAGE_MODE_2_LEVEL;
 	dma_dom->domain.pt_root = (void *)get_zeroed_page(GFP_KERNEL);
 	dma_dom->domain.flags = PD_DMA_OPS_MASK;
 	dma_dom->domain.priv = dma_dom;
-- 
GitLab


From 674d798a80cb6ea1defa01899099f40d9124423c Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 2 Sep 2009 17:26:09 +0200
Subject: [PATCH 1142/1153] x86/amd-iommu: Remove old page table handling
 macros

These macros are not longer required. So remove them.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/include/asm/amd_iommu_types.h | 19 -------------------
 1 file changed, 19 deletions(-)

diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h
index 1b4b3d6c9f0..d66430de5f7 100644
--- a/arch/x86/include/asm/amd_iommu_types.h
+++ b/arch/x86/include/asm/amd_iommu_types.h
@@ -150,11 +150,6 @@
 #define PAGE_MODE_5_LEVEL 0x05
 #define PAGE_MODE_6_LEVEL 0x06
 
-#define IOMMU_PDE_NL_0   0x000ULL
-#define IOMMU_PDE_NL_1   0x200ULL
-#define IOMMU_PDE_NL_2   0x400ULL
-#define IOMMU_PDE_NL_3   0x600ULL
-
 #define PM_LEVEL_SHIFT(x)	(12 + ((x) * 9))
 #define PM_LEVEL_SIZE(x)	(((x) < 6) ? \
 				  ((1ULL << PM_LEVEL_SHIFT((x))) - 1): \
@@ -164,15 +159,6 @@
 #define PM_LEVEL_PDE(x, a)	((a) | PM_LEVEL_ENC((x)) | \
 				 IOMMU_PTE_P | IOMMU_PTE_IR | IOMMU_PTE_IW)
 
-
-#define IOMMU_PTE_L2_INDEX(address) (((address) >> 30) & 0x1ffULL)
-#define IOMMU_PTE_L1_INDEX(address) (((address) >> 21) & 0x1ffULL)
-#define IOMMU_PTE_L0_INDEX(address) (((address) >> 12) & 0x1ffULL)
-
-#define IOMMU_MAP_SIZE_L1 (1ULL << 21)
-#define IOMMU_MAP_SIZE_L2 (1ULL << 30)
-#define IOMMU_MAP_SIZE_L3 (1ULL << 39)
-
 #define IOMMU_PTE_P  (1ULL << 0)
 #define IOMMU_PTE_TV (1ULL << 1)
 #define IOMMU_PTE_U  (1ULL << 59)
@@ -180,11 +166,6 @@
 #define IOMMU_PTE_IR (1ULL << 61)
 #define IOMMU_PTE_IW (1ULL << 62)
 
-#define IOMMU_L1_PDE(address) \
-	((address) | IOMMU_PDE_NL_1 | IOMMU_PTE_P | IOMMU_PTE_IR | IOMMU_PTE_IW)
-#define IOMMU_L2_PDE(address) \
-	((address) | IOMMU_PDE_NL_2 | IOMMU_PTE_P | IOMMU_PTE_IR | IOMMU_PTE_IW)
-
 #define IOMMU_PAGE_MASK (((1ULL << 52) - 1) & ~0xfffULL)
 #define IOMMU_PTE_PRESENT(pte) ((pte) & IOMMU_PTE_P)
 #define IOMMU_PTE_PAGE(pte) (phys_to_virt((pte) & IOMMU_PAGE_MASK))
-- 
GitLab


From a6b256b41357c33ccb2d105a4457e22bdc83e021 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 12:21:31 +0200
Subject: [PATCH 1143/1153] x86/amd-iommu: Support higher level PTEs in
 iommu_page_unmap

This patch changes fetch_pte and iommu_page_unmap to support
different page sizes too.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/include/asm/amd_iommu_types.h |  1 +
 arch/x86/kernel/amd_iommu.c            | 21 +++++++++++++--------
 2 files changed, 14 insertions(+), 8 deletions(-)

diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h
index d66430de5f7..351ca39ece0 100644
--- a/arch/x86/include/asm/amd_iommu_types.h
+++ b/arch/x86/include/asm/amd_iommu_types.h
@@ -158,6 +158,7 @@
 #define PM_LEVEL_ENC(x)		(((x) << 9) & 0xe00ULL)
 #define PM_LEVEL_PDE(x, a)	((a) | PM_LEVEL_ENC((x)) | \
 				 IOMMU_PTE_P | IOMMU_PTE_IR | IOMMU_PTE_IW)
+#define PM_PTE_LEVEL(pte)	(((pte) >> 9) & 0x7ULL)
 
 #define IOMMU_PTE_P  (1ULL << 0)
 #define IOMMU_PTE_TV (1ULL << 1)
diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index addf6588c36..002cf9cab9e 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -62,7 +62,7 @@ static void dma_ops_reserve_addresses(struct dma_ops_domain *dom,
 				      unsigned long start_page,
 				      unsigned int pages);
 static u64 *fetch_pte(struct protection_domain *domain,
-		      unsigned long address);
+		      unsigned long address, int map_size);
 static void update_domain(struct protection_domain *domain);
 
 #ifndef BUS_NOTIFY_UNBOUND_DRIVER
@@ -552,9 +552,9 @@ static int iommu_map_page(struct protection_domain *dom,
 }
 
 static void iommu_unmap_page(struct protection_domain *dom,
-			     unsigned long bus_addr)
+			     unsigned long bus_addr, int map_size)
 {
-	u64 *pte = fetch_pte(dom, bus_addr);
+	u64 *pte = fetch_pte(dom, bus_addr, map_size);
 
 	if (pte)
 		*pte = 0;
@@ -668,7 +668,7 @@ static int init_unity_mappings_for_device(struct dma_ops_domain *dma_dom,
  * there is one, it returns the pointer to it.
  */
 static u64 *fetch_pte(struct protection_domain *domain,
-		      unsigned long address)
+		      unsigned long address, int map_size)
 {
 	int level;
 	u64 *pte;
@@ -676,7 +676,7 @@ static u64 *fetch_pte(struct protection_domain *domain,
 	level =  domain->mode - 1;
 	pte   = &domain->pt_root[PM_LEVEL_INDEX(level, address)];
 
-	while (level > 0) {
+	while (level > map_size) {
 		if (!IOMMU_PTE_PRESENT(*pte))
 			return NULL;
 
@@ -684,6 +684,11 @@ static u64 *fetch_pte(struct protection_domain *domain,
 
 		pte = IOMMU_PTE_PAGE(*pte);
 		pte = &pte[PM_LEVEL_INDEX(level, address)];
+
+		if ((PM_PTE_LEVEL(*pte) == 0) && level != map_size) {
+			pte = NULL;
+			break;
+		}
 	}
 
 	return pte;
@@ -757,7 +762,7 @@ static int alloc_new_range(struct amd_iommu *iommu,
 	for (i = dma_dom->aperture[index]->offset;
 	     i < dma_dom->aperture_size;
 	     i += PAGE_SIZE) {
-		u64 *pte = fetch_pte(&dma_dom->domain, i);
+		u64 *pte = fetch_pte(&dma_dom->domain, i, PM_MAP_4k);
 		if (!pte || !IOMMU_PTE_PRESENT(*pte))
 			continue;
 
@@ -2192,7 +2197,7 @@ static void amd_iommu_unmap_range(struct iommu_domain *dom,
 	iova  &= PAGE_MASK;
 
 	for (i = 0; i < npages; ++i) {
-		iommu_unmap_page(domain, iova);
+		iommu_unmap_page(domain, iova, PM_MAP_4k);
 		iova  += PAGE_SIZE;
 	}
 
@@ -2207,7 +2212,7 @@ static phys_addr_t amd_iommu_iova_to_phys(struct iommu_domain *dom,
 	phys_addr_t paddr;
 	u64 *pte;
 
-	pte = fetch_pte(domain, iova);
+	pte = fetch_pte(domain, iova, PM_MAP_4k);
 
 	if (!pte || !IOMMU_PTE_PRESENT(*pte))
 		return 0;
-- 
GitLab


From abdc5eb3d69279039ba6cb89719913d08013ab14 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Thu, 3 Sep 2009 11:33:51 +0200
Subject: [PATCH 1144/1153] x86/amd-iommu: Change iommu_map_page to support
 multiple page sizes

This patch adds a map_size parameter to the iommu_map_page
function which makes it generic enough to handle multiple
page sizes. This also requires a change to alloc_pte which
is also done in this patch.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/include/asm/amd_iommu_types.h |  6 +++++
 arch/x86/kernel/amd_iommu.c            | 31 +++++++++++++++++---------
 2 files changed, 26 insertions(+), 11 deletions(-)

diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h
index 351ca39ece0..9e8bb9746dc 100644
--- a/arch/x86/include/asm/amd_iommu_types.h
+++ b/arch/x86/include/asm/amd_iommu_types.h
@@ -160,6 +160,12 @@
 				 IOMMU_PTE_P | IOMMU_PTE_IR | IOMMU_PTE_IW)
 #define PM_PTE_LEVEL(pte)	(((pte) >> 9) & 0x7ULL)
 
+#define PM_MAP_4k		0
+#define PM_ADDR_MASK		0x000ffffffffff000ULL
+#define PM_MAP_MASK(lvl)	(PM_ADDR_MASK & \
+				(~((1ULL << (12 + ((lvl) * 9))) - 1)))
+#define PM_ALIGNED(lvl, addr)	((PM_MAP_MASK(lvl) & (addr)) == (addr))
+
 #define IOMMU_PTE_P  (1ULL << 0)
 #define IOMMU_PTE_TV (1ULL << 1)
 #define IOMMU_PTE_U  (1ULL << 59)
diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 002cf9cab9e..45be9499c97 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -56,8 +56,8 @@ static int dma_ops_unity_map(struct dma_ops_domain *dma_dom,
 			     struct unity_map_entry *e);
 static struct dma_ops_domain *find_protection_domain(u16 devid);
 static u64 *alloc_pte(struct protection_domain *domain,
-		      unsigned long address, u64
-		      **pte_page, gfp_t gfp);
+		      unsigned long address, int end_lvl,
+		      u64 **pte_page, gfp_t gfp);
 static void dma_ops_reserve_addresses(struct dma_ops_domain *dom,
 				      unsigned long start_page,
 				      unsigned int pages);
@@ -523,17 +523,21 @@ void amd_iommu_flush_all_devices(void)
 static int iommu_map_page(struct protection_domain *dom,
 			  unsigned long bus_addr,
 			  unsigned long phys_addr,
-			  int prot)
+			  int prot,
+			  int map_size)
 {
 	u64 __pte, *pte;
 
 	bus_addr  = PAGE_ALIGN(bus_addr);
 	phys_addr = PAGE_ALIGN(phys_addr);
 
+	BUG_ON(!PM_ALIGNED(map_size, bus_addr));
+	BUG_ON(!PM_ALIGNED(map_size, phys_addr));
+
 	if (!(prot & IOMMU_PROT_MASK))
 		return -EINVAL;
 
-	pte = alloc_pte(dom, bus_addr, NULL, GFP_KERNEL);
+	pte = alloc_pte(dom, bus_addr, map_size, NULL, GFP_KERNEL);
 
 	if (IOMMU_PTE_PRESENT(*pte))
 		return -EBUSY;
@@ -612,7 +616,8 @@ static int dma_ops_unity_map(struct dma_ops_domain *dma_dom,
 
 	for (addr = e->address_start; addr < e->address_end;
 	     addr += PAGE_SIZE) {
-		ret = iommu_map_page(&dma_dom->domain, addr, addr, e->prot);
+		ret = iommu_map_page(&dma_dom->domain, addr, addr, e->prot,
+				     PM_MAP_4k);
 		if (ret)
 			return ret;
 		/*
@@ -729,7 +734,7 @@ static int alloc_new_range(struct amd_iommu *iommu,
 		u64 *pte, *pte_page;
 
 		for (i = 0; i < num_ptes; ++i) {
-			pte = alloc_pte(&dma_dom->domain, address,
+			pte = alloc_pte(&dma_dom->domain, address, PM_MAP_4k,
 					&pte_page, gfp);
 			if (!pte)
 				goto out_free;
@@ -1356,7 +1361,10 @@ static bool increase_address_space(struct protection_domain *domain,
 }
 
 static u64 *alloc_pte(struct protection_domain *domain,
-		      unsigned long address, u64 **pte_page, gfp_t gfp)
+		      unsigned long address,
+		      int end_lvl,
+		      u64 **pte_page,
+		      gfp_t gfp)
 {
 	u64 *pte, *page;
 	int level;
@@ -1367,7 +1375,7 @@ static u64 *alloc_pte(struct protection_domain *domain,
 	level =  domain->mode - 1;
 	pte   = &domain->pt_root[PM_LEVEL_INDEX(level, address)];
 
-	while (level > 0) {
+	while (level > end_lvl) {
 		if (!IOMMU_PTE_PRESENT(*pte)) {
 			page = (u64 *)get_zeroed_page(gfp);
 			if (!page)
@@ -1379,7 +1387,7 @@ static u64 *alloc_pte(struct protection_domain *domain,
 
 		pte = IOMMU_PTE_PAGE(*pte);
 
-		if (pte_page && level == 0)
+		if (pte_page && level == end_lvl)
 			*pte_page = pte;
 
 		pte = &pte[PM_LEVEL_INDEX(level, address)];
@@ -1403,7 +1411,8 @@ static u64* dma_ops_get_pte(struct dma_ops_domain *dom,
 
 	pte = aperture->pte_pages[APERTURE_PAGE_INDEX(address)];
 	if (!pte) {
-		pte = alloc_pte(&dom->domain, address, &pte_page, GFP_ATOMIC);
+		pte = alloc_pte(&dom->domain, address, PM_MAP_4k, &pte_page,
+				GFP_ATOMIC);
 		aperture->pte_pages[APERTURE_PAGE_INDEX(address)] = pte_page;
 	} else
 		pte += PM_LEVEL_INDEX(0, address);
@@ -2176,7 +2185,7 @@ static int amd_iommu_map_range(struct iommu_domain *dom,
 	paddr &= PAGE_MASK;
 
 	for (i = 0; i < npages; ++i) {
-		ret = iommu_map_page(domain, iova, paddr, prot);
+		ret = iommu_map_page(domain, iova, paddr, prot, PM_MAP_4k);
 		if (ret)
 			return ret;
 
-- 
GitLab


From ac0101d396fee24994632f71b55b9f7f9ee16eff Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Tue, 1 Sep 2009 16:00:35 +0200
Subject: [PATCH 1145/1153] x86/dma: Mark iommu_pass_through as __read_mostly

This variable is read most of the time. This patch marks it
as such. It also documents the meaning the this variable
while at it.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/pci-dma.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/arch/x86/kernel/pci-dma.c b/arch/x86/kernel/pci-dma.c
index 1a041bcf506..873aa079d16 100644
--- a/arch/x86/kernel/pci-dma.c
+++ b/arch/x86/kernel/pci-dma.c
@@ -32,7 +32,14 @@ int no_iommu __read_mostly;
 /* Set this to 1 if there is a HW IOMMU in the system */
 int iommu_detected __read_mostly = 0;
 
-int iommu_pass_through;
+/*
+ * This variable becomes 1 if iommu=pt is passed on the kernel command line.
+ * If this variable is 1, IOMMU implementations do no DMA ranslation for
+ * devices and allow every device to access to whole physical memory. This is
+ * useful if a user want to use an IOMMU only for KVM device assignment to
+ * guests and not for driver dma translation.
+ */
+int iommu_pass_through __read_mostly;
 
 dma_addr_t bad_dma_address __read_mostly = 0;
 EXPORT_SYMBOL(bad_dma_address);
-- 
GitLab


From 2650815fb03fe2bf1e6701584087ba669dcf92cd Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 26 Aug 2009 16:52:40 +0200
Subject: [PATCH 1146/1153] x86/amd-iommu: Add core functions for pd
 allocation/freeing

This patch factors some code of protection domain allocation
into seperate functions. This way the logic can be used to
allocate the passthrough domain later. As a side effect this
patch fixes an unlikely domain id leakage bug.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 36 ++++++++++++++++++++++++++++++++----
 1 file changed, 32 insertions(+), 4 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 6c99f503780..0934348abfa 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -1988,19 +1988,47 @@ static void cleanup_domain(struct protection_domain *domain)
 	write_unlock_irqrestore(&amd_iommu_devtable_lock, flags);
 }
 
-static int amd_iommu_domain_init(struct iommu_domain *dom)
+static void protection_domain_free(struct protection_domain *domain)
+{
+	if (!domain)
+		return;
+
+	if (domain->id)
+		domain_id_free(domain->id);
+
+	kfree(domain);
+}
+
+static struct protection_domain *protection_domain_alloc(void)
 {
 	struct protection_domain *domain;
 
 	domain = kzalloc(sizeof(*domain), GFP_KERNEL);
 	if (!domain)
-		return -ENOMEM;
+		return NULL;
 
 	spin_lock_init(&domain->lock);
-	domain->mode = PAGE_MODE_3_LEVEL;
 	domain->id = domain_id_alloc();
 	if (!domain->id)
+		goto out_err;
+
+	return domain;
+
+out_err:
+	kfree(domain);
+
+	return NULL;
+}
+
+static int amd_iommu_domain_init(struct iommu_domain *dom)
+{
+	struct protection_domain *domain;
+
+	domain = protection_domain_alloc();
+	if (!domain)
 		goto out_free;
+
+	domain->mode    = PAGE_MODE_3_LEVEL;
 	domain->pt_root = (void *)get_zeroed_page(GFP_KERNEL);
 	if (!domain->pt_root)
 		goto out_free;
@@ -2010,7 +2038,7 @@ static int amd_iommu_domain_init(struct iommu_domain *dom)
 	return 0;
 
 out_free:
-	kfree(domain);
+	protection_domain_free(domain);
 
 	return -ENOMEM;
 }
-- 
GitLab


From 0feae533ddebe02cda6ccce5cac7349b446776a8 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Wed, 26 Aug 2009 15:26:30 +0200
Subject: [PATCH 1147/1153] x86/amd-iommu: Add passthrough mode initialization
 functions

When iommu=pt is passed on kernel command line the devices
should run untranslated. This requires the allocation of a
special domain for that purpose. This patch implements the
allocation and initialization path for iommu=pt.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/include/asm/amd_iommu.h       |  1 +
 arch/x86/include/asm/amd_iommu_types.h |  4 ++
 arch/x86/kernel/amd_iommu.c            | 72 +++++++++++++++++++++++---
 3 files changed, 69 insertions(+), 8 deletions(-)

diff --git a/arch/x86/include/asm/amd_iommu.h b/arch/x86/include/asm/amd_iommu.h
index bdf96f119f0..ac95995b7ba 100644
--- a/arch/x86/include/asm/amd_iommu.h
+++ b/arch/x86/include/asm/amd_iommu.h
@@ -25,6 +25,7 @@
 #ifdef CONFIG_AMD_IOMMU
 extern int amd_iommu_init(void);
 extern int amd_iommu_init_dma_ops(void);
+extern int amd_iommu_init_passthrough(void);
 extern void amd_iommu_detect(void);
 extern irqreturn_t amd_iommu_int_handler(int irq, void *data);
 extern void amd_iommu_flush_all_domains(void);
diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h
index 0c878caaa0a..49f7453bff7 100644
--- a/arch/x86/include/asm/amd_iommu_types.h
+++ b/arch/x86/include/asm/amd_iommu_types.h
@@ -143,6 +143,7 @@
 #define EVT_BUFFER_SIZE		8192 /* 512 entries */
 #define EVT_LEN_MASK		(0x9ULL << 56)
 
+#define PAGE_MODE_NONE    0x00
 #define PAGE_MODE_1_LEVEL 0x01
 #define PAGE_MODE_2_LEVEL 0x02
 #define PAGE_MODE_3_LEVEL 0x03
@@ -194,6 +195,9 @@
 #define PD_DMA_OPS_MASK		(1UL << 0) /* domain used for dma_ops */
 #define PD_DEFAULT_MASK		(1UL << 1) /* domain is a default dma_ops
 					      domain for an IOMMU */
+#define PD_PASSTHROUGH_MASK	(1UL << 2) /* domain has no page
+					      translation */
+
 extern bool amd_iommu_dump;
 #define DUMP_printk(format, arg...)					\
 	do {								\
diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 0934348abfa..7987f20499a 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -41,6 +41,12 @@ static DEFINE_RWLOCK(amd_iommu_devtable_lock);
 static LIST_HEAD(iommu_pd_list);
 static DEFINE_SPINLOCK(iommu_pd_list_lock);
 
+/*
+ * Domain for untranslated devices - only allocated
+ * if iommu=pt passed on kernel cmd line.
+ */
+static struct protection_domain *pt_domain;
+
 #ifdef CONFIG_IOMMU_API
 static struct iommu_ops amd_iommu_ops;
 #endif
@@ -1067,9 +1073,9 @@ static struct protection_domain *domain_for_device(u16 devid)
  * If a device is not yet associated with a domain, this function does
  * assigns it visible for the hardware
  */
-static void attach_device(struct amd_iommu *iommu,
-			  struct protection_domain *domain,
-			  u16 devid)
+static void __attach_device(struct amd_iommu *iommu,
+			    struct protection_domain *domain,
+			    u16 devid)
 {
 	unsigned long flags;
 	u64 pte_root = virt_to_phys(domain->pt_root);
@@ -1087,12 +1093,19 @@ static void attach_device(struct amd_iommu *iommu,
 
 	amd_iommu_pd_table[devid] = domain;
 	write_unlock_irqrestore(&amd_iommu_devtable_lock, flags);
+}
 
-       /*
-        * We might boot into a crash-kernel here. The crashed kernel
-        * left the caches in the IOMMU dirty. So we have to flush
-        * here to evict all dirty stuff.
-        */
+static void attach_device(struct amd_iommu *iommu,
+			  struct protection_domain *domain,
+			  u16 devid)
+{
+	__attach_device(iommu, domain, devid);
+
+	/*
+	 * We might boot into a crash-kernel here. The crashed kernel
+	 * left the caches in the IOMMU dirty. So we have to flush
+	 * here to evict all dirty stuff.
+	 */
 	iommu_queue_inv_dev_entry(iommu, devid);
 	iommu_flush_tlb_pde(iommu, domain->id);
 }
@@ -2219,3 +2232,46 @@ static struct iommu_ops amd_iommu_ops = {
 	.domain_has_cap = amd_iommu_domain_has_cap,
 };
 
+/*****************************************************************************
+ *
+ * The next functions do a basic initialization of IOMMU for pass through
+ * mode
+ *
+ * In passthrough mode the IOMMU is initialized and enabled but not used for
+ * DMA-API translation.
+ *
+ *****************************************************************************/
+
+int __init amd_iommu_init_passthrough(void)
+{
+	struct pci_dev *dev = NULL;
+	u16 devid, devid2;
+
+	/* allocate passthroug domain */
+	pt_domain = protection_domain_alloc();
+	if (!pt_domain)
+		return -ENOMEM;
+
+	pt_domain->mode |= PAGE_MODE_NONE;
+
+	while ((dev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, dev)) != NULL) {
+		struct amd_iommu *iommu;
+
+		devid = calc_devid(dev->bus->number, dev->devfn);
+		if (devid > amd_iommu_last_bdf)
+			continue;
+
+		devid2 = amd_iommu_alias_table[devid];
+
+		iommu = amd_iommu_rlookup_table[devid2];
+		if (!iommu)
+			continue;
+
+		__attach_device(iommu, pt_domain, devid);
+		__attach_device(iommu, pt_domain, devid2);
+	}
+
+	pr_info("AMD-Vi: Initialized for Passthrough Mode\n");
+
+	return 0;
+}
-- 
GitLab


From aa879fff5d12318259816aa35023e941a1e4d3d9 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Mon, 31 Aug 2009 16:01:48 +0200
Subject: [PATCH 1148/1153] x86/amd-iommu: Fix device table write order

The V bit of the device table entry has to be set after the
rest of the entry is written to not confuse the hardware.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 7987f20499a..2b1e77c714f 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -1087,9 +1087,9 @@ static void __attach_device(struct amd_iommu *iommu,
 	pte_root |= IOMMU_PTE_IR | IOMMU_PTE_IW | IOMMU_PTE_P | IOMMU_PTE_TV;
 
 	write_lock_irqsave(&amd_iommu_devtable_lock, flags);
-	amd_iommu_dev_table[devid].data[0] = lower_32_bits(pte_root);
-	amd_iommu_dev_table[devid].data[1] = upper_32_bits(pte_root);
 	amd_iommu_dev_table[devid].data[2] = domain->id;
+	amd_iommu_dev_table[devid].data[1] = upper_32_bits(pte_root);
+	amd_iommu_dev_table[devid].data[0] = lower_32_bits(pte_root);
 
 	amd_iommu_pd_table[devid] = domain;
 	write_unlock_irqrestore(&amd_iommu_devtable_lock, flags);
-- 
GitLab


From eba6ac60ba66c6bf6858938442204feaa67dea31 Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Tue, 1 Sep 2009 12:07:08 +0200
Subject: [PATCH 1149/1153] x86/amd-iommu: Align locking between attach_device
 and detach_device

This patch makes the locking behavior between the functions
attach_device and __attach_device consistent with the
locking behavior between detach_device and __detach_device.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 2b1e77c714f..9aa135d4453 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -1077,29 +1077,38 @@ static void __attach_device(struct amd_iommu *iommu,
 			    struct protection_domain *domain,
 			    u16 devid)
 {
-	unsigned long flags;
-	u64 pte_root = virt_to_phys(domain->pt_root);
+	u64 pte_root;
 
-	domain->dev_cnt += 1;
+	/* lock domain */
+	spin_lock(&domain->lock);
+
+	pte_root = virt_to_phys(domain->pt_root);
 
 	pte_root |= (domain->mode & DEV_ENTRY_MODE_MASK)
 		    << DEV_ENTRY_MODE_SHIFT;
 	pte_root |= IOMMU_PTE_IR | IOMMU_PTE_IW | IOMMU_PTE_P | IOMMU_PTE_TV;
 
-	write_lock_irqsave(&amd_iommu_devtable_lock, flags);
 	amd_iommu_dev_table[devid].data[2] = domain->id;
 	amd_iommu_dev_table[devid].data[1] = upper_32_bits(pte_root);
 	amd_iommu_dev_table[devid].data[0] = lower_32_bits(pte_root);
 
 	amd_iommu_pd_table[devid] = domain;
-	write_unlock_irqrestore(&amd_iommu_devtable_lock, flags);
+
+	domain->dev_cnt += 1;
+
+	/* ready */
+	spin_unlock(&domain->lock);
 }
 
 static void attach_device(struct amd_iommu *iommu,
 			  struct protection_domain *domain,
 			  u16 devid)
 {
+	unsigned long flags;
+
+	write_lock_irqsave(&amd_iommu_devtable_lock, flags);
 	__attach_device(iommu, domain, devid);
+	write_unlock_irqrestore(&amd_iommu_devtable_lock, flags);
 
 	/*
 	 * We might boot into a crash-kernel here. The crashed kernel
-- 
GitLab


From 21129f786f231f7a9dce5b504617b893f50a435f Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Tue, 1 Sep 2009 11:59:42 +0200
Subject: [PATCH 1150/1153] x86/amd-iommu: Make sure a device is assigned in
 passthrough mode

When the IOMMU driver runs in passthrough mode it has to
make sure that every device not assigned to an IOMMU-API
domain must be put into the passthrough domain instead of
keeping it unassigned.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index 9aa135d4453..a8e74c34dd2 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -1141,6 +1141,15 @@ static void __detach_device(struct protection_domain *domain, u16 devid)
 
 	/* ready */
 	spin_unlock(&domain->lock);
+
+	/*
+	 * If we run in passthrough mode the device must be assigned to the
+	 * passthrough domain if it is detached from any other domain
+	 */
+	if (iommu_pass_through) {
+		struct amd_iommu *iommu = amd_iommu_rlookup_table[devid];
+		__attach_device(iommu, pt_domain, devid);
+	}
 }
 
 /*
-- 
GitLab


From a1ca331c8aa75cd58fdf685e2e8745e1d3ec5c8f Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Tue, 1 Sep 2009 12:22:22 +0200
Subject: [PATCH 1151/1153] x86/amd-iommu: Don't detach device from pt domain
 on driver unbind

This patch makes sure a device is not detached from the
passthrough domain when the device driver is unloaded or
does otherwise release the device.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c
index a8e74c34dd2..12a541deae5 100644
--- a/arch/x86/kernel/amd_iommu.c
+++ b/arch/x86/kernel/amd_iommu.c
@@ -1195,6 +1195,8 @@ static int device_change_notifier(struct notifier_block *nb,
 	case BUS_NOTIFY_UNBOUND_DRIVER:
 		if (!domain)
 			goto out;
+		if (iommu_pass_through)
+			break;
 		detach_device(domain, devid);
 		break;
 	case BUS_NOTIFY_ADD_DEVICE:
-- 
GitLab


From 4751a95134e05f1172131d2001c6991d671fa58c Mon Sep 17 00:00:00 2001
From: Joerg Roedel <joerg.roedel@amd.com>
Date: Tue, 1 Sep 2009 15:53:54 +0200
Subject: [PATCH 1152/1153] x86/amd-iommu: Initialize passthrough mode when
 requested

This patch enables the passthrough mode for AMD IOMMU by
running the initialization function when iommu=pt is passed
on the kernel command line.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/kernel/amd_iommu_init.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/arch/x86/kernel/amd_iommu_init.c b/arch/x86/kernel/amd_iommu_init.c
index c1b17e97252..f00f489ab15 100644
--- a/arch/x86/kernel/amd_iommu_init.c
+++ b/arch/x86/kernel/amd_iommu_init.c
@@ -1242,12 +1242,18 @@ int __init amd_iommu_init(void)
 	if (ret)
 		goto free;
 
-	ret = amd_iommu_init_dma_ops();
+	if (iommu_pass_through)
+		ret = amd_iommu_init_passthrough();
+	else
+		ret = amd_iommu_init_dma_ops();
 	if (ret)
 		goto free;
 
 	enable_iommus();
 
+	if (iommu_pass_through)
+		goto out;
+
 	printk(KERN_INFO "AMD IOMMU: device isolation ");
 	if (amd_iommu_isolate)
 		printk("enabled\n");
-- 
GitLab


From 6ac162d6c01ac7626f46c68c0770556cf682ce34 Mon Sep 17 00:00:00 2001
From: Pavel Vasilyev <pavel@pavlinux.ru>
Date: Thu, 3 Sep 2009 16:20:55 +0200
Subject: [PATCH 1153/1153] x86/gart: Do not select AGP for GART_IOMMU

There is no dependency from the gart code to the agp code.
And since a lot of systems today do not have agp anymore
remove this dependency from the kernel configuration.

Signed-off-by: Pavel Vasilyev <pavel@pavlinux.ru>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
---
 arch/x86/Kconfig | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 13ffa5df37d..1d9c18aa17e 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -586,7 +586,6 @@ config GART_IOMMU
 	bool "GART IOMMU support" if EMBEDDED
 	default y
 	select SWIOTLB
-	select AGP
 	depends on X86_64 && PCI
 	---help---
 	  Support for full DMA access of devices with 32bit memory access only
-- 
GitLab